MI-110
Mini-ITX Embedded Motherboard with Intel® Atom™
Processor N270 and Intel® 945GSE/ICH7M Chipset
User’s Manual
Manual Rev.:
2.00
Revision Date:
October 2, 2009
Part No:
50-1Z012-1000
Advance Technologies; Automate the World.
Revision History
Revision
Release Date
2.00
2009/10/02
Description of Change(s)
Initial Release
MI-110
Preface
Copyright 2009 ADLINK Technology Inc.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks
of their respective companies.
Preface
iii
Using this Manual
Audience and Scope
The MI-110 User’s Manual is intended for hardware technicians
and systems operators with knowledge of installing, configuring
and operating industrial grade computers.
Manual Organization
This manual is organized as follows:
Preface: Presents copyright notifications, disclaimers, trademarks, and associated information on the proper usage of this
document and its associated product(s).
Chapter 1, Introduction: Introduces the MI-110, its features,
applications, and specifications, including functional descriptions
and board layout.
Chapter 2, Connectors & Jumpers: Provides technical information on connectors, jumpers and pin assignments for configuring
the MI-110.
Chapter 3, Getting Started: Describes how to install components
and drivers on the MI-110.
Chapter 4, BIOS Setup: Presents information and illustrations to
help understand and configure the system BIOS.
Appendix A, Watchdog Timer: Presents information on understanding and configuring the watchdog timer.
Appendix B, System Resources: Presents information on I/O
mapping, IRQ routing, and resource allocation.
Important Safety Instructions: Presents safety instructions all
users must follow for the proper setup, installation and usage of
equipment and/or software.
Getting Service: Contact information for ADLINK’s worldwide
offices.
iv
Preface
MI-110
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
Additional information, aids, and tips that help users perform
tasks.
NOTE:
CAUTION:
WARNING:
Preface
Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.
v
This page intentionally left blank.
vi
Preface
MI-110
Table of Contents
Revision History...................................................................... ii
Preface .................................................................................... iii
Table of Contents.................................................................. vii
List of Figures ........................................................................ ix
List of Tables.......................................................................... xi
1 Introduction ........................................................................ 1
1.1
Package Contents ............................................................... 1
1.2
Overview.............................................................................. 2
1.3
Features............................................................................... 2
1.4
Specifications....................................................................... 3
1.5
Block Diagram ..................................................................... 5
1.6
Functional Description ......................................................... 6
1.7
Power Consumption ............................................................ 9
1.8
Board Layout ..................................................................... 10
1.9
Mechanical Dimensions..................................................... 12
2 Connectors & Jumpers.................................................... 15
2.1
Rear I/O Connectors.......................................................... 15
2.2
Onboard Connectors ......................................................... 19
2.3
Jumper Settings................................................................. 27
3 Getting Started ................................................................. 31
3.1
System Memory................................................................. 31
3.2
Driver Installation ............................................................... 32
4 BIOS Setup........................................................................ 33
4.1
Starting the BIOS............................................................... 33
Table of Contents
vii
4.2
Standard CMOS Features ................................................. 35
4.3
Advanced BIOS Features .................................................. 37
4.4
Advanced Chipset Features............................................... 42
4.5
Integrated Peripherals........................................................ 44
4.6
Power Management Setup ................................................ 51
4.7
PnP/PCI Configurations ..................................................... 54
4.8
PC Health Status ............................................................... 56
4.9
Frequency/Voltage Control ................................................ 57
4.10 Load Optimized Defaults.................................................... 58
4.11 Set Supervisor & User Password....................................... 59
4.12 Save & Exit Setup .............................................................. 60
4.13 Exit Without Saving............................................................ 61
A Appendix: Watchdog Timer ..............................................63
A.1
WDT Programming Instructions......................................... 63
B Appendix: System Resources ..........................................65
B.1
System Memory Map ......................................................... 65
B.2
Direct Memory Access Channels....................................... 66
B.3
Fixed I/O Map .................................................................... 67
B.4
Variable I/O Map ................................................................ 68
B.5
Interrupt Request (IRQ) Lines............................................ 69
B.6
PCI Configuration Space Map ........................................... 71
B.7
PCI Interrupt Routing Map ................................................. 72
Important Safety Instructions............................................... 73
Getting Service ...................................................................... 75
viii
Table of Contents
MI-110
List of Figures
Figure 1-1:
Figure 1-2:
Figure 1-3:
Figure 1-4:
Figure 1-5:
MI-110 Block Diagram ..................................................... 5
MI-110 Board Layout ..................................................... 10
MI-110 Rear I/O Layout ................................................. 11
MI-110 Board Dimensions ............................................. 12
Rear I/O Faceplate Dimensions..................................... 13
List of Figures
ix
This page intentionally left blank.
x
List of Figures
MI-110
List of Tables
Table
Table
Table
Table
Table
Table
Table
Table
Table
Table
Table
1-1:
1-2:
1-3:
B-1:
B-2:
B-3:
B-4:
B-5:
B-6:
B-7:
B-8:
List of Tables
MI-110 General Specifications......................................... 4
Intel® Atom™ N270 processor Power Consumption ...... 9
MI-110 Board Layout Legend ........................................ 11
System Memory Map..................................................... 65
Direct Memory Access Channels................................... 66
Fixed I/O Map ................................................................ 67
Variable I/O Map............................................................ 68
IRQ Lines PIC Mode...................................................... 69
IRQ Lines APIC Mode ................................................... 70
PCI Configuration Space Map ....................................... 71
PCI Interrupt Routing Map ............................................. 72
xi
This page intentionally left blank.
xii
List of Tables
MI-110
1
Introduction
This chapter will introduce the MI-110, its features, specifications,
functional description, and mechanical layout.
1.1 Package Contents
Please check that your package contains the items below. If
you discover damaged or missing items, please contact your
vendor.
X
MI-110 Mini-ITX Embedded Motherboard
X
I/O shield
X
1x IDE cable
X
2x SATA cable
X
2x SATA power cable
X
2x COM port cable with bracket
X
Driver CD
X
User’s Manual
WARNING:
Introduction
DO NOT install or apply power to equipment that is damaged
or if there is missing/incomplete equipment. Retain the shipping carton and packing materials for inspection. Please contact your ADLINK dealer/vendor immediately for assistance.
Obtain authorization from your dealer before returning any
product to ADLINK.
1
1.2 Overview
The ADLINK MI-110 is a Mini-ITX embedded motherboard based
on the Intel® Atom™ processor N270 built on 45-nm process
technology in Micro-FCBGA8 package and the Mobile Intel®
945GSE + ICH7M Express Chipset. The MI-110 is ideal for
embedded applications requiring fanless operation and ultra-low
power consumption in a standard small form factor motherboard
with a complete set of I/O functions and high-bandwidth network
connectivity. These features, combined with an SO-DIMM socket
supporting DDR2-533 SDRAM up to 2 GB, IDE/SATA/CF storage
interfaces, PCI and Mini PCIe expansion slots, VGA, DVI-I, dualchannel 18-bit LVDS, and audio interfaces make the MI-110 suitable for medical, transportation, and other applications requiring a
low noise/power, space-saving, multiple display platform.
1.3 Features
2
X
Mini-ITX form factor (170 mm x 170 mm)
X
Intel® Atom™ processor N270:
Z
1.6 GHz core frequency
Z
533MHz FSB
Z
512KB L2 cache
Z
Micro-FCBGA8 package
X
DDR2-533 up to 2GB max. (1x 200-pin SODIMM socket)
X
Intel® GMA950 integrated in 945GSE supporting dual independent display
Z
Dsub-15 connector up to 2048x1536 @ 75Hz (QXGA)
Z
DVI-I via Chrontel 7307C, up to 1600x1200 (UXGA)
Z
Dual-channel 18-bit LVDS up to 1600x1200 (UXGA)
X
PCI and Mini PCIe expansion slots
X
2x SATA ports 1.5Gb/s, 4x RS-232 serial ports
X
2x GbE, 6x USB 2.0 (4 ext., 2 int.)
X
2x Mini-DIN for PS/2 keyboard/mouse
X
RoHS compliant
Introduction
MI-110
1.4 Specifications
System
CPU
Intel® Atom™ processor N270
• 1.6 GHz core frequency
• 512KB L2 cache
• Micro-FCBGA8 package
FSB
• 533 MHz
Chipset
• Mobile Intel® 945GSE + ICH7M Express Chipset
Memory
• DDR2 533 SDRAM (2GB max.)
• 1x 200-pin SO-DIMM slot
BIOS
• Award BIOS with 16 Mb Flash ROM
TPM
• TPM 1.2 via Infineon SLB 9635 TT 1.2
Audio
• Realtek ALC888 HD Audio
• Line-in, line-out and mic-in
Watchdog Timer
• 1-255 second/minute programmable
Hardware Monitor • CPU/System temperature, fan speed and onboard DC
voltage
Operating System • Microsoft® Windows® XP/Vista
I/O Interfaces
Serial ATA
• 2x Serial ATA ports with 1.5 Gb/s data transfer
Parallel ATA
• 1x 40-pin ATA-66/100 IDE port
CompactFlash
• 1x Type-II CF socket, shared with IDE port
Onboard I/O
• 6x USB 2.0 (4x external, 2x by pin header)
• 4x RS-232 serial ports (2x external, 2x by pin header)
Rear I/O
•
•
•
•
•
•
•
Expansion Slots
• 1x Mini PCIe slot
• 1x PCI slot
Introduction
2x RJ-45 LAN ports
4x USB 2.0 ports
2x RS-232 serial ports
1x D-Sub VGA connector
1x DVI-I connector
2x PS2 keyboard/mouse ports
3x audio jacks (line-in, line-out and mic-in)
3
Display
Graphics
Processor
• Intel® GMA950 integrated in 945GSE supporting dual
independent display
VRAM
• Shared system memory up to 224 MB
CRT
• Dsub-15 connector up to 2048x1536 @ 75Hz (QXGA)
DVI
• DVI-I via Chrontel 7307C, up to 1600x1200 (UXGA)
LVDS
• Dual-channel 18-bit LVDS up to 1600x1200 (UXGA)
Controller
• Realtek 8111C GbE controller
Ports
• 2x RJ-45 Ethernet port
Ethernet
Mechanical and Environment
Form Factor
• Mini-ITX Embedded Motherboard
Dimensions
• 170 mm x 170 mm (L x W)
Operating Temp.
• 0°C to 60°C
Storage Temp.
• -40ºC to 80ºC
Rel. Humidity
• 10 - 90% RH
Safety
• CE, FCC Class A
Table 1-1: MI-110 General Specifications
4
Introduction
MI-110
1.5 Block Diagram
CPU
Intel® Atom™
N270
1.6GHz 533 MHz FSB
512K L2 Cache
437-pin Micro-FCBGA8
533 MHz FSB
CRT
SO-DIMM up to 2GB
Northbridge
DB-15
Intel® 945GSE GMCH
Dual Channel
18-bit LVDS
DDRII 533MHz
Chrontel 7307C
DVI Transmitter
DVI
DMI
Interface
2 GB/s
Southbridge
PCIe x1
PCIe Mini slot
PCIe x1
RTL8111C
RJ-45
PCIe x1
RTL8111C
RJ-45
PCI Bus
PCI 32-bit/
33MHz bus
®
Intel ICH7M
IDE / CF
SATA ports x2
USB 2.0
(Bracket x4, Internal x2)
IDE
PCIe
Controller
SATA
USB 2.0
AC97
LPC
PCI
Controller
SPI
Realtek ALC888
Audio Codec
Audio Jacks
Line-in, Line-out, Mic-in
KB/Mouse
KB/Mouse
RS-232x4
Winbond
W83627DHG-A
LPC Super I/O
SPI BIOS
Hardware
Monitor
Figure 1-1: MI-110 Block Diagram
Introduction
5
1.6 Functional Description
Processor Support
The MI-110 embedded motherboard is equpped with the Intel®
Atom™ N270 processor in Micro-FCBGA8 package. Implemented
in 45nm process technology, the Intel® Atom™ N270 is poweroptimized to deliver robust performance per watt for cost-effective
embedded applications. Features include:
X
1.6 GHz core speed with 533 MHz FSB and 2.5 watts TDP
X
Hyper-Threading Technology
X
Enhanced Intel SpeedStep® Technology
X
Enhanced low-power sleep states (C1E, C2E, C4E)
X
Dynamic L2 cache sizing
Mobile Intel® 945GSE Express Chipset
The MI-110 is based on the Mobile Intel® 945GSE Express
Chipset, consisting of the Intel® 82945GSE Graphics Memory
Controller Hub and Intel® I/O Controller Hub 7-M. The chipset features power-efficient graphics with an integrated 32-bit 3D graphics engine based on Intel® Graphics Media Accelerator 950
architecture with SDVO, LVDS, and CRT display ports. It provides
rich I/O capabilities and flexibility via high-bandwidth interfaces
such as PCI Express, PCI, Serial ATA, and Hi-Speed USB 2.0
connectivity. It also includes a single channel for 400/533 MHz
DDR2 system memory, and Intel® High Definition Audio interface.
DDR2 memory
To meet the requirements of memory-intensive applications, the
MI-110 has a single-channel memory architecture supporting a
DDR2 400/533 MHz SO-DIMM. The high-bandwidth memory
specification, meets the requirements of the latest 3D graphics,
multimedia, and network application, and boosts system performance by eliminating bottlenecks.
6
Introduction
MI-110
Intel® Graphics Media Accelerator GMA 950
The Intel® Graphics Media Accelerator (GMA) 950 provides an
integrated 3D graphics engine delivering sophisticated graphics
for large display applications. With support for DirectX 9 hardware
acceleration, 400 MHz display clock, and up to 224 MB of video
memory, the Intel GMA 950 provides a cost-effective and high-performance graphics solution. The MI-110 supports dual independent display technology, enabling different content to be displayed
on two separate display terminals or a single workspace to be
stretched across two display devices.
Gigabit Ethernet
The MI-110 is equipped with the PCI Express Realtek 8111C GbE
controller.
Serial ATA
Storage is efficient and secure with the Serial ATA interface. Utilizing the Intel® ICH7M, the MI-110 supports two Serial ATA devices
capable of reading/writing data at up to 1.5 Gb/s. The SATA specification improves chassis airflow via thinner and more flexible
cables with lower pin count.
USB 2.0
The MI-110 incorporates the Universal Serial Bus (USB) 2.0 specification that increases peripheral connection speed from 12 Mbps
(USB 1.1) to 480 Mbps. USB 2.0 is backward compatible with
USB 1.1.
Hardware Monitoring
A built-in, proactive hardware monitoring system monitors the
CPU temperature, system fan speeds, and voltage levels to prevent overheating and/or component damage, effect timely failure
detection, and ensure stable supply of current for critical motherboard components.
Introduction
7
Watchdog Timer
The watchdog timer (WDT) monitors system operations based on
user-defined configurations. The WDT can be programmed for different time-out periods, such as from 1 to 255 seconds or from 1 to
255 minutes. The WDT generates a reset signal, then a reset
request, after failure to strobe it within the programmed time
period. A register bit may be enabled to indicate if the watchdog
timer caused the reset event. The WDT register is cleared during
the power-on sequence to enable the operating system to take
appropriate action when the watchdog generates a reboot.
8
Introduction
MI-110
1.7 Power Consumption
Intel® Atom™ N270 processor, 1.6GHz, 512KB L2 cache, 533MHz FSB
Test Configuration
Memory
Elpida DDR2 667MHz, 2GB
Graphics
Intel® Graphics Media Accelerator 950
SATA HD
WD Caviar SE, WD1600JS-60NCB1, 160GB
Power Supply
Sunpower SPX-5600P1 500W
DOS (idle)
Power Req.
+5VSB
+12V
Total
Current (mA)
–
719.4
–
Watts (W)
–
–
8.633
Windows XP, Idle
Power Req.
+5V
+12V
Total
Current (mA)
–
695.8
–
Watts (W)
–
–
8.350
Windows XP, CPU Stress (Kpower)
Power Req.
+5V
+12V
Total
Current (mA)
–
890.0
–
Watts (W)
–
–
10.68
Windows XP, Total System Stress (Burnin)
Power Req.
+5V
+12V
Total
Current (mA)
–
860.5
–
Watts (W)
–
–
10.326
S4 Mode (Windows hibernate)
Power Req.
+5V
+12V
Total
Current (mA)
162.8
–
–
Watts (W)
–
–
0.814
S3 Mode
Power Req.
+5V
+12V
Total
Current (mA)
252.2
–
–
Watts (W)
–
–
1.261
Table 1-2: Intel® Atom™ N270 processor Power Consumption
Introduction
9
1.8 Board Layout
Figure 1-2: MI-110 Board Layout
10
Introduction
MI-110
AAFP1
Front Panel Audio pin
header
JCOMPWR1/2 COM1/2 RI, +12V and
+5V power select jumper
ATXPWR1
ATX Power connector
JCOMPWR3/4
COM3/4 RI, +12V and
+5V power select jumper
CHA_FAN
System Fan connector
JDIO
Digital IO pin header
CLRTC
Clear CMOS jumper
JLVDS1
LVDS connector
COM3/4
Serial Port pin headers
SATA1/2
SATA1/2 connectors
F_PANEL1
System Panel pin header SODIMMA1
SO-DIMM socket
IDE1
IDE connector
S/PDIF pin header
JAMP1
Audio Amplifier connector SPI_JP1
SPI pin header
JBLK1
LCD Inverter pin header
USB4/5 pin header
SPDIF_OUT
USB45
Table 1-3: MI-110 Board Layout Legend
PS/2
KB/MS
COM
DVI
COM
VGA
RJ-45 + USB
Audio
Figure 1-3: MI-110 Rear I/O Layout
Introduction
11
1.9 Mechanical Dimensions
Dimensions in mm
Figure 1-4: MI-110 Board Dimensions
12
Introduction
MI-110
Dimensions in mm
Figure 1-5: Rear I/O Faceplate Dimensions
Introduction
13
This page intentionally left blank.
14
Introduction
MI-110
2
Connectors & Jumpers
The connectors and jumpers on the MI-110 allow you to connect
and configure external devices. The following specify the pin
assignments for connectors and jumper on the MI-110. Refer to
Figure 1-2: MI-110 Board Layout and Figure 1-3: MI-110 Rear
I/O Layout for connector and jumper locations.
2.1 Rear I/O Connectors
PS/2 Mouse Port (green)
Pin #
Signal
Function
1
MSDATA
Mouse Data
2
NC
not connected
3
GND
Ground
4
+5V
Power
5
CLK
Clock
6
NC
not connected
PS/2 Keyboard Port (purple)
Pin #
Signal
Function
1
KBDATA
Keyboard Data
2
NC
not connected
3
GND
Ground
4
+5V
Power
5
CLK
Clock
6
NC
not connected
Connectors & Jumpers
15
Serial Port Connectors (COM1/2)
Pin #
RS-232
1
DCD, Data Carrier Detect
2
RXD, Receive Data
3
TXD, Transmit Data
4
DTR, Data Terminal Ready
5
GND, ground
6
DSR, Data Set Ready
7
RTS, Request to Send
8
CTS, Clear to Send
9
RI_Power,
Ring Indicator / Power*
*Note: See “Jumper Settings” on page 27 for RI/+5V/+12V selection.
VGA Connector.
Signal Name Pin # Pin # Signal Name
16
Red
1
2
Green
Blue
3
4
VCC pull-up
GND
5
6
GND
GND
7
8
GND
VCC
9
10
GND
VCC pull-up
11
12
DDC2B DATA
HSYNC
13
14
VSYNC
DDC2B CLK
15
Connectors & Jumpers
MI-110
DVI-I Connector (CN2)
Pin #
Signal
Pin #
Signal
1
TMDS Data2-
16
Hot Plug Detect
2
TMDS Data2+
17
TMDS Data0-
3
TMDS Data2/4 Shield
18
TMDS Data0+
4
TMDS Data4-
19
TMDS Data0/5 Shield
5
TMDS Data4+
20
TMDS Data5-
6
DDC Clock
21
TMDS Data5+
7
DDC Data
22
TMDS Clock Shield
8
Analog Vertical Sync
23
TMDS Clock +
9
TMDS Data1-
24
TMDS Clock -
10
TMDS Data1+
C1
Analog Red
11
TMDS Data1/3 Shield
C2
Analog Green
12
TMDS Data3-
C3
Analog Blue
13
TMDS Data3+
C4
Analog Horizontal Sync
14
+5 V Power
C5
Analog GND Return
15
GND
Connectors & Jumpers
17
USB Connectors
Pin # Signal Name
1
Vcc
2
USB-
3
USB+
4
GND
LAN Port (RJ-45)
This port allows gigabit connection to a Local Area Network (LAN)
using a network hub. The LAN port comes with two LEDs to indicate link, activity and speed. Refer to the tables below for the LAN
port pin and LED definitions ..
Pin #
10BASET/100BASE-TX
1000BASE-T
1
TX+
BI_DA+
2
TX-
BI_DA-
3
RX+
BI_DB+
4
--
BI_DC+
5
--
BI_DC-
6
RX-
BI_DB-
7
--
BI_DD+
8
--
BI_DD-
ACT/LINK
1
8
SPEED
Status
Description
Status
Description
Off
No Link
Off
10 Mb connection
Orange
Linked
Orange
100 Mb connection
Blinking
Data Activity
Green
1 Gb connection
Audio I/O port
The three-jack audio I/O supports Line-In, Line-Out, and Mic-In
functions. The blue Line-In jack onnects to an audio source such
as a CD player. The green Line-Out port connects to a speaker or
headphone, while the pink Mic-In jack connects to a microphone.
18
Connectors & Jumpers
MI-110
2.2 Onboard Connectors
Front Panel Audio Pin Header (AAFP1)
Pin #
Signal
Pin #
Signal
1
MIC2_L
6
AGND
2
MIC2_R
7
FP_PRES#
3
MIC2_R
8
SRTN1
4
SENSE A
9
Key
5
LIN2_L
10
SRTN2
1
2
ATX Power Connector (ATXPWR1)
Pin #
Signal
Pin #
Signal
1
+3.3V
11
+3.3V
2
+3.3V
12
-12V
3
GND
13
GND
4
+5V
14
PS-ON#
5
GND
15
GND
6
+5V
16
GND
7
GND
17
GND
8
PWRGD
18
NC
9
+5VSB
19
+5V
10
+12V
20
+5V
System Fan Connector (CHA_FAN)
Pin #
Signal
1
GND
2
Fan Power (+12V)
3
Fan Tachometer
Connectors & Jumpers
3
1
19
Serial Port Connectors (COM3/4)
Pin #
Signal
Functions
1
DCD
Data Carrier Detect
2
TXD
Transmit Data
3
GND
Ground
4
RTS
Request to Send
5
RI_Power
6
RXD
Receive Data
7
DTR
Data Terminal Ready
8
DSR
Data Set Ready
9
CTS
Clear to Send
10
NC
Key
1
6
Ring Indicate, Power *
5
*Note: See “Jumper Settings” on page 27 for RI/+5V/+12V selection.
20
Connectors & Jumpers
MI-110
System Panel Connector (F_PANEL1)
Pin #
Signal
1
HD_LED+
2
HD_LED-
3
GND
4
RESET
5
NC
6
PWR_LED+
7
PWR_LED-
8
PWR
9
GND
10
NC
Connectors & Jumpers
Pin Group
Hard Disk LED
Reset Button
1
Power LED
5
6
Power Switch
21
IDE Connector (IDE1)
Pin #
Signal
Pin #
Signal
1
Reset
2
Ground
3
Data 7
4
Data 8
5
Data 6
6
Data 9
7
Data 5
8
Data 10
9
Data 4
10
Data 11
11
Data 3
12
Data 12
13
Data 2
14
Data 13
15
Data 1
16
Data 14
17
Data 0
18
Data 15
19
Ground
20
-
21
Request
22
Ground
23
I/O Write
24
Ground
25
I/O Read
26
Ground
27
I/O Ready
28
Cable Select
29
DMA Ack
30
Ground
31
Interrupt Request
32
No Connect
33
Device Address 1
34
ATA 66/100 Detect
35
Device Address 0
36
Device Address 2
37
Chip Select 1
38
Chip Select 3
39
Device Active
40
Ground
Audio Amplifier connector (JAMP1)
22
Pin #
Signal
1
AMP_L-
2
AMP_L+
3
AMP_R-
4
AMP_R+
1
Connectors & Jumpers
MI-110
LCD Inverter pin header (JBLK1)
Pin #
Signal
1
+12V
2
GND
3
ENBKL
4
VR
5
+5V
1
Digital IO pin header (JDIO)
Pin #
Signal
Pin #
Signal
1
DIO GP20
2
DIO GP10
3
DIO GP21
4
DIO GP11
5
DIO GP22
6
DIO GP12
7
DIO GP23
8
DIO GP13
9
DIO GP24
10
DIO GP14
11
DIO GP25
12
DIO GP15
13
DIO GP26
14
DIO GP16
15
DIO GP27
16
DIO GP17
17
SMBCLK
18
SMBDATA
19
Ground
20
VCC
Connectors & Jumpers
1
2
23
LVDS Flat Panel Connector (JLVDS1)
24
Pin #
Signal
Pin #
Signal
2
+5V
1
+3.3V
4
+5V
3
+3.3V
6
SD_DDC
5
SC_DDC
8
GND
7
GND
10
LVDS0_P0
9
LVDS0_P1
12
LVDS0_N0
11
LVDS0_N1
14
GND
13
GND
16
LVDS0_P2
15
LVDS0_P3
18
LVDS0_N2
17
LVDS0_N3
20
GND
19
GND
22
LVDS1_P0
21
LVDS1_P1
24
LVDS1_N0
23
LVDS1_N1
26
GND
25
GND
28
LVDS1_P2
27
LVDS1_P3
30
LVDS1_N2
29
LVDS1_N3
32
GND
31
GND
34
LVDS0_CLKP
33
LVDS1_CLKP
36
LVDS0_CLKN
35
LVDS1_CLKN
38
GND
37
GND
40
+12V
39
+12V
Connectors & Jumpers
MI-110
SATA Connectors (SATA1-6)
Pin #
Signal
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
1
7
S/PDIF Pin Header (SPDIF_OUT)
Pin #
Signal
1
+5V
2
NC
3
SPDIF0
4
GND
Connectors & Jumpers
1
25
SPI pin header (SPI_JP1)
Pin #
Signal
Pin #
Signal
1
+3V ROM
2
GND
3
F_SPI_CS#
4
F_SPI_CLK
5
F_SPI_MISO
6
F_SPI_MOSI
7
SPI_HOLD#
8
NC
1
USB 2.0 Connector (USB45)
26
Pin #
Signal
Pin #
Signal
1
+5V
2
+5V
3
USB4-
4
USB5-
5
USB4+
6
USB5+
7
GND
8
GND
9
Key
10
NC
Connectors & Jumpers
MI-110
2.3 Jumper Settings
Clear CMOS Jumper (CLRTC)
The CMOS RAM data contains the date / time and BIOS setting
information. CMOS is powered by the onboard button cell battery.
To erase the CMOS RAM data:
1. Unplug the MI-110.
2. Short the CLRTC pins 2-3.
3. Remove the jumper cap from pins 2-3 and reinstall it to
pins 1-2. Power up the system.
Connectors & Jumpers
27
COM1 RI, +12V and +5V Function Select (JCOMPWR1/2)
These jumpers allows you to select COM1 RI, +5V and +12V functions. Set JCOMPWR1 to pins 1-3 and JCOMPWR2 to pins 1-3 to
select +5V power. Set JCOMPWR1 to pins 3-5 and JCOMPWR2
to pins 1-3 to select +12V power. Set JCOMPWR2 to pins 3-5 and
JCOMPWR1 to open for RI selection.
COM2 RI, +12V and +5V Function Select (JCOMPWR1/2)
These jumpers allow you to select COM2 RI, +5V and +12V
power. Set JCOMPWR1 to pins 2-4 and JCOMPWR2 to pins 2-4
to select +5V power. Set JCOMPWR1 to pins 4-6 and
JCOMPWR2 to pins 2-4 to select +12V power. Set JCOMPWR2 to
pins 4-6 and JCOMPWR1 to open for RI selection.
28
Connectors & Jumpers
MI-110
COM3 RI, +12V and +5V Function Select (JCOMPWR3/4)
These jumpers allow you to select COM3 RI, +5V and +12V
power. Set JCOMPWR3 to pins 1-3 and JCOMPWR4 to pins 1-3
to select +5V power. Set JCOMPWR3 to pins 3-5 and
JCOMPWR4 to pins 1-3 to select +12V power. Set JCOMPWR4 to
pins 3-5 and JCOMPWR3 to open for RI selection.
COM4 RI, +12V and +5V Function Select (JCOMPWR3/4)
These jumpers allow you to select COM4 RI, +5V and +12V
power. Set JCOMPWR3 to pins 2-4 and JCOMPWR4 to pins 2-4
to select +5V power. Set JCOMPWR3 to pins 4-6 and
JCOMPWR4 to pins 2-4 to select +12V power. Set JCOMPWR4 to
pins 4-6 and JCOMPWR3 to open for RI selection.
Connectors & Jumpers
29
This page intentionally left blank.
30
Connectors & Jumpers
MI-110
3
Getting Started
This chapter provides information on how to install components to
the MI-110 SBC.
3.1 System Memory
The MI-110 supports up to 2 GB of DDR2 400/533 SDRAM in one
200-pin SO-DIMM socket. See Figure 1-2 on page 10 for the
SO-DIMM socket location.
Memory Module Installation
The DDR2 memory modules are notched to facilitate correct
installation in the DIMM sockets.
WARNING:
Disconnect all power supply to the board before installing a
memory module to prevent damaging the board and memory module .
To install a memory module:
1. Locate the SO-DIMM slot on the motherboard.
2. Align the memory module on the socket, making sure
that the notch matches the break on the socket.
3. Insert the module firmly into the slot until the retaining clips
snap back inwards and the module is securely seated.
Getting Started
31
3.2 Driver Installation
The MI-110 drivers for Windows XP 32-bit are located in the following directories on the Driver CD, or can be downloaded from
the ADLINK website (http://www.adlinktech.com):
Chipset
X:\MI-110\CHIP\setup.exe
Display
X:\MI-110\VGA\Win2KXP\win2k_xp14311.exe
LAN
X:\MI-110\LAN\Win2KXP\setup.exe
Audio
X:\MI-110\Audio\Windows 32_64\WDM_R182.exe
TPM
X:\MI-110\TPM\setup.exe
Follow the instructions below to install the required MI-110 drivers:
1. Install the Windows operating system before installing any
driver. Most standard I/O device drivers are installed during
Windows installation.
2. Install the Chipset driver by running the program
X:\MI-110\CHIP\setup.exe. Follow the instructions given and
reboot when instructed.
3. Install the Display driver and utilities by running the program
X:\MI-110\VGA\Win2KXP\win2k_xp14311.exe. Follow the
instructions given and reboot when instructed.
4. Install the LAN driver by running the program
X:\MI-110\LAN\Win2KXP\setup.exe. Follow the instructions
given and reboot if required.
5. Install the Audio driver by running the program
X:\MI-110\Audio\Windows 32_64\WDM_R182.exe. Follow the
instructions given and reboot if required.
6. Install the TPM driver by running the program
X:\MI-110\TPM\setup.exe. Follow the instructions given and
reboot if required.
32
Getting Started
MI-110
4
BIOS Setup
The following chapter describes basic navigation for the Phoenix
AwardBIOS Setup Utility.
4.1 Starting the BIOS
To enter the setup screen, follow these steps:
1. Power on the motherboard
2. Press the <Delete> key on your keyboard during the
Power-On-Self-Test (POST) to enter the Setup utility.
3. After you press the < Delete > key, the main BIOS Setup
Menu will be displayed.
BIOS Setup
33
Navigation
Use the keys described below to navigate through the BIOS Setup
Utility
Key(s)
Function Description
F1
General help, only for Status Page Setup Menu and
Option Page Setup Menu
Esc
Return to the main menu from a sub-menu or prompts
you to quit the setup program.
←,→
Move to the item on the left or right
↑,↓
Move to previous or next item
Enter
Brings up a selection menu for the highlighted field.
+ or PgUp
Moves the cursor to the first field
- or PgDn
Moves the cursor to the last field
F5
F6, F7
F10
Loads the previous values
Loads the fail-safe / optimized defaults
Saves changes and exits Setup
Submenus
Note that a right pointer symbol (X) appears to the left of certain
fields. This pointer indicates that you can display a submenu from
this field. A sub-menu contains additional options for a field parameter. To display a sub-menu, move the highlight to the field and
press <Enter>. The sub-menu appears. Use the legend keys to
enter values and move from field to field within a sub-menu as you
would within a menu. Use the <Esc> key to return to the main
menu.
34
BIOS Setup
MI-110
4.2 Standard CMOS Features
The main menu includes the following setup categories. Recall
that some systems may not include all entries.
Date/Time
Use this option to change the system time and date. The date
must be entered in MM/DD/YY format. The time is entered in
HH:MM:SS format.
Note:
The time is in 24-hour format. For example, 5:30 A.M. appears as
05:30:00, and 5:30 P.M. as 17:30:00.
IDE Channel 0/1 Master/Slave
This selection brings up the configuration submenu of the designated device.
IDE HDD Auto-detection: Press Enter to auto-detect the HDD on
the selected channel.
IDE Device Setup: None/Auto/Manual. Selecting 'manual' allows
the user to set the remaining fields on the submenu.
BIOS Setup
35
Capacity: Auto display disk size Disk drive capacity (approximated).
Access Mode: CHS/LBA/Large/Auto Selects the access mode
for a hard disk The following options are selectable only if the
'IDE Primary Master' item is set to 'Manual'
Cylinder: Min = 0 Max = 65535 Sets the number of cylinders
for a hard disk.
Head: Min = 0 Max = 255 Sets the number of read/write heads
Precomp: Min = 0 Max = 65535
Landing zone: Min = 0 Max = 65535
Sector: Min = 0 Max = 255 Number of sectors per track
Video
This category detects the type of adapter used for the primary
monitor that matches your video display card and monitor.
X
EGA / VGA: Enhanced Graphics Adapter/Video Graphics
Array. For EGA, VGA, SVGA, or PGA monitor adapters
X
CGA 40: Color Graphics Adapter, power up in 40 column
mode
X
CGA 80: Color Graphics Adapter, power up in 80 column
mode
X
MONO: Monochrome adapter, includes high resolution
monochrome adapters
Halt On
Sets the system to halt on errors according to the system functions
specified in each option. Configuration options: [All Errors] [No
Errors] [All, But Keyboard]
Memory
This category displays base memory, extended memory, and total
memory detected during POST (Power On Self Test).
36
BIOS Setup
MI-110
4.3 Advanced BIOS Features
This section allows users to configure the Advanced BIOS Features of the system.
BIOS Setup
37
CPU Features
Delay Prior to Thermal
The Delay Prior To Thermal BIOS feature controls the activation of
the Thermal Monitor's automatic mode. It allows you to determine
when the Pentium 4's Thermal Monitor should be activated in automatic mode after the system boots. For example, with the default
value of 16 Minutes, the BIOS activates the Thermal Monitor in
automatic mode 16 minutes after the system starts booting up.
Limit CPUID MaxVal
Set Limit CPUID MaxVa1 to 3. This should be disabled for WinXP
C1E Function
CPU C1E function select
Execute Disable Bit
When disabled, forces the XD feature flag to always return 0
38
BIOS Setup
MI-110
Hard Disk Boot Priority
Sets hard disk boot device priority.
CH0 S.
Primary SATA channel with Master Device. It will show the device
model / type when SATA HDD or CD ROM connected.
Bootable Add-in Cards
"Bootable add-in cards" is an item on the HDD boot priority list.
Virus Warning
Enables or disables the virus warning.
CPU L1 & L2 Cache
Enables or disables the CPU L1 & L2 Cache. Enabling this feature
speeds up memory access.
Hyper-Threading Technology
BIOS Setup
39
Enables or disables the Hyper-Threading function of the CPU.
Quick Power On Self Test
Speeds up the Power On Self Test (POST). If enabled, the BIOS
will shorten the test time or skip some check items during POST.
First/Second/Third Boot Device
Pressing <Enter> displays the Boot Device Menu. The BIOS will
attempt to load the operating system from the selected devices in
sequence.
Boot Other Device
Enables the BIOS to boot from a second or third device if booting
from the first device fails. When disabled the BIOS will not attempt
to boot from alternative devices.
Boot-Up NumLock Status
Selects the power on state for system NumLock. Options: On/Off
Gate A20 Option
Gate A20 is a device used to address memory above 1 MB. The
options are Fast and Normal. The Fast setting is controlled by a
chipset specific method. Normal setting is controlled by keyboard
controller or chipset hardware.
Security Option
Selects whether a password is required every time the system
boots or only when setup is entered. Options include:
X
System: The system will not boot without password access
and access to Setup will be denied if an incorrect password
is entered at the prompt.
X
Setup: The system will boot, but access to Setup will be
restricted without password access.
To disable security, select PASSWORD SETTINGS in the Main
Menu. The user will then be prompted to enter a password. To disable security, DO NOT type anything, only press <Enter>. Once
security is disabled, the system will boot and setup can be
accessed.
APIC Mode
Enables or disables the APIC Mode.
40
BIOS Setup
MI-110
MPS Version Control for OS
This option is only valid for multiprocessor motherboards as it
specifies the version of the Multiprocessor Specification (MPS)
that the motherboard will use. The MPS is a specification by which
PC manufacturers design and build Intel architecture systems with
two or more processors.
MPS 1.1 was the original specification. MPS version 1.4 adds
extended configuration tables for improved support of multiple PCI
bus configurations and greater expandability in the future. In addition, MPS 1.4 introduces support for a secondary PCI bus without
requiring a PCI bridge.
Small Logo (EPA) Show
This item allows you enabled/disabled display of the small EPA
logo during POST.
BIOS Setup
41
4.4 Advanced Chipset Features
DRAM Clock/Drive Control
When set to “BySPD”, the DRAM timing parameters are set
according to DRAM SPD (Serial Presence Detect). When disabled, one can manually set the DRAM timing parameters using
the sub items below. Set to “BySPD” if not sure.
CAS Latency Time
Controls the latency between the SDRAM Read command and the
time data actually becomes available.
DRAM RAS# to CAS# Delay
Controls the latency between the DDR SDRAM active command
and the read/write command.
DRAM RAS# Precharge
Controls the idle clocks after issuing a precharge command to the
DDR SDRAM.
Precharge delay (tRAS)
This setting controls the precharge delay, which determines the
timing delay for DRAM precharge.
System Memory Frequency
Allow to choose different frequency of memory module.
42
BIOS Setup
MI-110
System BIOS Cacheable
Selecting “Enabled” allows caching of the system BIOS ROM at
F0000h- FFFFFh, resulting in better system performance. However, if any pro-gram writes data to this memory area, a system
error may occur.
Video BIOS Cacheable
Selecting Enabled allows caching of the video BIOS ROM at
F0000h-FFFFFh, resulting in better video performance. However, if
any program writes to this memory area, a system error may result.
Memory Hole At 15M-16M
Enabling this feature reserves 15 MB to 16 MB memory address
space for ISA expansion cards that specifically require this setting.
This makes memory from 15 MB and up unavailable to the system. Expansion cards can only access memory up to 16 MB. The
default setting is “Disabled”.
On-Chip Frame Buffer Size
The On-Chip Frame Buffer Size can be set as 1MB or 8MB. This
memory is shared with the system memory.
DVMT Mode
Use this field to select the memory to allocate for video memory.
The choices are “Fixed”, “DVMT” and “BOTH”.
DVMT/FIXED Memory Size
Specify the size of DVMT/system memory to allocate for video
memory.
Boot Display
Options: VBIOS Default, CRT, LFP, CRT+LFP, EFP(DVI),
CRT+EFP(DVI). (VBIOS Default: CRT, LFP: LVDS Flat Panel,
EFP(DVI): DVI)
Panel Number (LVDS panel resolution)
Options: 640x480 18bit, 800x600
1024x768 18bit/2 (dual channel).
BIOS Setup
18bit,
1024x768
18bit,
43
4.5 Integrated Peripherals
44
BIOS Setup
MI-110
On Chip IDE Device
IDE HDD Block Mode
If your IDE hard drive supports block mode select Enabled for
automatic detection of the optimal number of block read/writes
per sector the drive can support.
IDE DMA Transfer Access
Use this field to enable or disable IDE DMA transfer access.
OnChip Primary/Seondary PCI IDE
The integrated peripheral controller contains an IDE interface
with support for two IDE channels. Select Enabled to activate
each channel separately.
IDE Primary/Secondary Master/Slave PIO/UDMA Mode
Two IDE devices may have a different Mode timing (0, 1, 2, 3,
4), which need to be independent. The default setting “Auto”
will allow auto detection to ensure optimal performance.
On-Chip SerialATA
Options: Disabled, Auto, Combined Mode, Enhanced Mode,
SATA only
BIOS Setup
45
Onboard Device
Azalia Audio Select
Select [Disabled] if you do not want to use Azalia audio. Configuration options: [Enabled] [Disabled]
46
BIOS Setup
MI-110
Super I/O Device
Power ON Function
This feature allows you to wake up the system using any of the
listed options. The selections are “Hot KEY”, “Mouse Left”,
“Mouse Right”, “Any KEY” and “BUTTON ONLY” (default).
KB Power ON Password
The system will ask for a password, after entering the correct
password the keyboard can then be used.
Hot Key Power ON
Awaken the system by pressing the hot key button. The options
are “Ctrl-F1”, “Ctrl-F2”, “Ctrl-F3” to “Ctrl-F8”.
Onboard Serial Port 1/2
The settings are “3F8/IRQ4”, “2F8/IRQ3”, “3E8/IRQ4”,
“2E8/IRQ3”, and “Disabled” for the on-board serial connector.
Onboard Parallel Port
BIOS Setup
47
This field sets the address of the on-board parallel port connector. You can select “378/IRQ7”, “278/IRQ5”, “3BC/IRQ7”, or
“Disabled”. If you install an I/O card with a parallel port, make
sure there is no conflict in the address assignments. The single
board computer can support up to three parallel ports.
PWRON After PWR-Fail
Determines which state the computer enters when AC power is
restored after a power loss. The options for this value are On,
Off, and Former-Sts.
Onboard LAN1/2 Boot ROM
Options: Enable, Disable.
Watchdog Timer Select
This option will determine watch dog timer. Options: Disabled, 10,
20, 30, 40 Sec. 1, 2, 4 Min.
Onboard Serial Port 3/4
Options: Disable, 3F8, 2F8, 3E8, 2E8
Serial Port 3/4 Use IRQ
Options: IRQ3, IRQ4, IRQ10, IRQ11
48
BIOS Setup
MI-110
USB Device Setting
USB Controller
The options: Disabled, Enabled.
USB 2.0 Controller
The options: Disabled, Enabled.
USB Operation Mode
Allows you to configure the USB 2.0 controller in HiSpeed (480
Mbps) or Full Speed (12 Mbps). Configuration options: [Full/Low
Speed] [HiSpeed]
USB Keyboard Function
The options: Disabled, Enabled.
USB Mouse Function
The options: Disabled, Enabled.
USB Storage Function
The options: Disabled, Enabled.
BIOS Setup
49
Security Chip Configuration
TPM Support
The choices are “Enabled” and “Disabled”.
TPM Current Status
This item shows you the current TPM status.
TPM Status
The options are “No Change” / “Clear” / “Enable & Activate” /
“Deactivate & Disable”.
50
BIOS Setup
MI-110
4.6 Power Management Setup
ACPI Function
The options are “Enabled” and “Disabled”.
ACPI Suspend Type
This item allows you to set ACPI suspend type to S1/POS (Power
On Suspend) or S3/STR (Suspend To RAM).
Run VGABIOS if S3 Resume
Select “Auto” to run VGA BIOS if S3 resume automatically. The
“Yes” enables running VGA BIOS if S3 resume. The “No” disables
this function.
Power Management
There are three selections for Power Management, and each of
them has fixed mode settings.
X
Min. Power Saving: Minimum power management, HDD
Power Down = 15 Min,
BIOS Setup
51
X
Max. Power Saving: Maximum power management, HDD
Power Down =1 Min
X
User Defined: Allows you to set each mode individually.
When not disabled, each of the ranges are from 1 min. to 1
hr. except for HDD Power Down which ranges from 1 min.
to 15 min. and disable.
Video Off Method
Use this to select the method to turn off the video. The options are
“Blank Screen”, “V/H SYNC+ Blank”, and “DPMS”.
Video Off In Suspend
When the system is in suspend mode, the video will turn off. The
options are “No” and “Yes”.
Suspend Type
Select the suspend type. The choice: Stop Grant, Pwron suspend.
MODEM Use IRQ
This determines the IRQ in which the MODEM can use. The
options: NA, 3, 4, 5, 7, 9, 10, 11.
Suspend Mode
Enable/disable system suspend.
HDD Power Down
Select “1-15 mins” to enable HDD Power Down mode between 1
to 15 mins. Select “Disabled” to disable HDD Power Down function.
Soft-Off by PWR-BTTN: Configures the power button:
X
Instant-Off: The power button functions as a normal poweron/-off button.
X
Delay 4 Sec: The system is turned off if the power button is
pressed for more than four seconds. Pressing the button
momentarily (for less than 4 seconds) will switch the system
to “suspend” mode.
Wake-Up by PCI card
The options are “Enabled” and “Disabled”.
52
BIOS Setup
MI-110
Power On by Ring
Select “Enabled” to power on the system from a soft off state by an
input signal on the serial Ring Indicator (RI) line. The options are
“Enabled” and “Disabled”.
USB KB Wake-Up from S3
When “Enabled”, enter any key to wake up the system from S3
state. The options are “Enabled” and “Disabled”.
Resume by Alarm
When “Enabled”, set the date and time at which the RTC (realtime clock) alarm awakens the system from suspend mode. The
options are “Enabled” and “Disabled”.
BIOS Setup
53
4.7 PnP/PCI Configurations
This section describes configuring the PCI (Personal Computer
Interconnect) bus system. PCI is a system which allows I/O
devices to operate at speeds nearing the speed the CPU itself
uses when communicating with its own components.
Init Display First
This item allows you to choose the first display interface to initiate
while booting. The choice is “PCI Slot” or “Onboard”.
Reset Configuration Data
The default is “Disabled”. Select Enabled to reset Extended System Configuration Data (ESCD) if you have installed a new add-on
card, and system configuration is in such a state that the OS cannot boot.
Resource Controlled By
The commands here are “Auto (ESCD)” or “Manual”. Choosing
“Manual” requires you to choose resources from the following submenu. “Auto(ESCD)” automatically configures all of the boot and
Plug and Play devices, but you must be using Windows 95 or
above.
54
BIOS Setup
MI-110
PCI/VGA Palette Snoop
This is set to “Disabled” by default.
INT Pin 1/2/3/4/5/6/7/8 Assignment
The options: Auto, 3, 4, 5, 7, 9, 10, 11
Maximum Payload Size
This allows you to set the maximum TLP payload size for PCI
Express devices. The options are [128 bytes], [256 bytes], [512
bytes], [1024 bytes], [2048 bytes], and [4096 bytes].
BIOS Setup
55
4.8 PC Health Status
Shutdown Temperature
Options: 60 °C/140 °F, 65 °C/149 °F, 70 °C/158 °F, Disabled
CPU Warning Temperature
Options: Disabled, 50 °C/122 °F, 53 °C/127 °F, 56 °C/133 °F,
60 °C/140 °F, 63 °C/145 °F, 66 °C/151 °F, 70 °C/158 °F
56
BIOS Setup
MI-110
4.9 Frequency/Voltage Control
Auto Detect PCI Clk
This allows you to enable or disable auto detect PCI clock.
Options: Enabled, Disabled.
Spread Spectrum
This setting allows you to reduce EMI by modulating the signals
the CPU generates so that the spikes are reduced to flatter
curves. This is achieved by varying the frequency slightly so that
the signal does not use any particular frequency for more than a
moment. Options: Enabled, Disabled.
CPU/Host/SRC/PCI Clock
Options: Default, 133/100/33
BIOS Setup
57
4.10 Load Optimized Defaults
Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. Press “Y” to load
the default values setting for optimal performance system operations.
58
BIOS Setup
MI-110
4.11 Set Supervisor & User Password
These two options set the system password. Supervisor Password
sets a password that will be used to protect the system and Setup
utility. User Password sets a password that will be used exclusively on the system. To specify a password, highlight the type you
want and press < Enter >. The “Enter Password:” message
prompts you on the screen. Type the password, up to eight characters in length, and press < Enter >. The system confirms your
password by asking you to type it again. After setting a password,
the screen automatically returns to the main screen.
BIOS Setup
59
4.12 Save & Exit Setup
This option allows you to determine whether to accept any modifications or not. Typing Y will quit the setup utility and save all
changes into the CMOS memory. Typing “N” will return to the
Setup Utility Main Screen.
60
BIOS Setup
MI-110
4.13 Exit Without Saving
Select this option to exit the Setup utility without saving the
changes you have made in this session. Typing “Y” will quit the
Setup utility without saving any modifications. Typing “N” will
return to the Setup utility.
BIOS Setup
61
This page intentionally left blank.
62
BIOS Setup
MI-110
Appendix A - Watchdog Timer
The programming instructions for the MI-110’s Watchdog Timer
are as follows.
A.1 WDT Programming Instructions
Unlock W83627DHG-A:
outportb(0x2E, 0x87)
;Unlock Super I/O
Select Logical Device:
outportb(0x2E, 0x07)
outportb(0x2F, 0x08)
;Select device number register
;Set to Logical Device 8
Activate WDT:
outportb(0x2E, 0x30)
outportb(0x2F, 0x01)
;Select WDTO# activate register
;Enable watchdog
Set Seconds or Minutes:
outportb(0x2E, 0xF5)
outportb(0x2F, mode)
;Select WDTO# control register
;where mode=0x00(Sec) or 0x08(Min)
Set base timer:
outportb(0x2E, 0xF6)
;Select WDTO# counter register
outportb(0x2F, timeout) ;where timeout=0x00~0xFF
Reset timeout counter:
outportb(0x2E, 0xF6)
;Select WDTO# counter register
outportb(0x2F, timeout) ;where timeout=0x00~0xFF}
Watchdog Timer
63
This page intentionally left blank.
64
Watchdog Timer
MI-110
Appendix B - System Resources
B.1 System Memory Map
Address Range Address Range
(decimal)
(hex)
Size
Description
(4GB-2MB)
FFE00000 –
FFFFFFFF
2 MB
High BIOS Area
(4GB-18MB) –
(4GB-17MB-1)
FEE00000 –
FEEFFFFF
1 MB
FSB Interrupt Memory Space
(4GB-20MB) –
(4GB-19MB-1)
FEC00000 –
FECFFFFF
1 MB
APIC Configuration Space
15MB – 16MB
F00000 –
FFFFFF
1 MB
ISA Hole
960 K – 1024 K
F0000 – FFFFF
64 KB
System BIOS Area
896 K – 960 K
E0000 – EFFFF
64 KB
Extended System BIOS Area
768 K – 896 K
C0000 – DFFFF
PCI expansion ROM area
C0000 – CBFFF: Onboard VGA BIOS
128 KB CC000 – CCFFF: Intel 82566DM PXE
option ROM when onboard LAN boot
ROM is enabled.
640 K – 768 K
A0000 – BFFFF
128 KB Video Buffer & SMM space
0 K – 640 K
00000 – 9FFFF
640 KB DOS Area
Table B-1: System Memory Map
Note: Whole D0000H segment except PXE occupied area can be forwarded to ISA bus.
System Resources
65
B.2 Direct Memory Access Channels
Channel Number
Data Width
System Resource
0
8-bits
1
8-bits
Parallel port(1)
2
8-bits
Diskette drive(1)
3
8-bits
Parallel port(1)
4
8-bits
Direct memory access controller
5
16-bits
Open
6
16-bits
Open
7
16-bits
Open
Table B-2: Direct Memory Access Channels
Note(1): DMA channel 1/3 is selected when using parallel port. Floppy
(Winbond default uses DMA 02) and parallel port cannot be used at the
same time.
66
System Resources
MI-110
B.3 Fixed I/O Map
Hex Range
000-01F
020-02D and
030-03F
02E-02F
040-042-043
4E-4F
061
60,62,64,66
Device
DMA controller 1, 82C37 equivalent
Interrupt controller 1, 8259 equivalent
LPC SIO (W83627) configuration index/data registers
Timer/Counter
N/A
NMI controller
N/A (MicroController)
070-077
Real Time Clock Controller
080-9F
DMA Controller, or LPC or PCI
0A0-0AD and
0B4-0BD
Interrupt controller
0B2 and 0B3
Power Management
0C0-0DF
0F0
DMA controller
Read PCI and Master Abord, Write FERR#/IGNNE#/
Interrupt Controller
0170-177
SATA Controller, or PCI
01F0-1F7
SATA Controller, or PCI
0376
SATA Controller, or PCI
03F6
SATA Controller, or PCI
04D0-4D1
0CF9
Interupt Controller
Reset Generator
Table B-3: Fixed I/O Map
System Resources
67
B.4 Variable I/O Map
Hex Range
Device
400
ACPI
Anywhere in 64KB I/O Space
USB UHCI Controller #1
Anywhere in 64KB I/O Space
USB UHCI Controller #2
Anywhere in 64KB I/O Space
USB UHCI Controller #3
Anywhere in 64KB I/O Space
USB UHCI Controller #4
Anywhere in 64KB I/O Space
USB UHCI Controller #5
500
SMBUS
460
TCO
480
378-37F
GPIO
Parallel Port
3F8/2F8/3E8/2E8
Serial Port 1 Serial Port 2
3E8/2E8
Serial Port 3, Serial Port 4
290
Hardware Monitor
Table B-4: Variable I/O Map
68
System Resources
MI-110
B.5 Interrupt Request (IRQ) Lines
IRQ Lines PIC Mode
IRQ#
Typical Interrupt
Resource
Connected to Pin
Note
0
System timer
N/A
No
3
Communications port
(COM2)
IRQ3 via SERIRQ,
IRQ3 at ISA bus
Note (1)
4
Communications port
(COM1)
IRQ4 via SERIRQ,
IRQ4 at ISA bus
Note (1)
5
Intel® 82801G (ICH7)
SMBus controller - 27DA
8
System CMOS /
Real-time clock
9
Microsoft ACPI-compliant
system
10
Communications port
(COM3)
IRQ10 via SERIRQ,
IRQ10 at ISA bus
Note (1)
11
Communications port
(COM4)
IRQ11 via SERIRQ,
IRQ11 at ISA bus
Note (1)
13
Numeric data processor
14
Primary IDE controller
Table B-5: IRQ Lines PIC Mode
Note(1): These IRQs can be used for PCI devices when onboard
device is disabled. If IRQ is from ISA, user must reserve IRQ for ISA in
BIOS setup menu.
System Resources
69
IRQ Lines APIC Mode
IRQ#
Typical Interrupt Resource
Connected to Pin
Note
0
System Timer
3
Communications port (COM2)
IRQ3 via SERIRQ,
IRQ3 at ISA bus
Note (1)
4
Communications port (COM1)
IRQ4 via SERIRQ,
IRQ4 at ISA bus
Note (1)
5
Intel® 82801G (ICH7) SMBus
controller - 27DA
8
System CMOS /
Real-time clock
9
Microsoft ACPI-compliant system
10
Communications port (COM3)
IRQ10 via SERIRQ,
IRQ10 at ISA bus
Note (1)
11
Communications port (COM4)
IRQ11 via SERIRQ,
IRQ11 at ISA bus
Note (1)
13
Numeric data processor
14
Primary IDE controller
16
PCI standard PCI-to-PCI bridge
16
Standard Universal PCI to USB Host
Controller
18
PCI standard PCI-to-PCI bridge
18
Realtek RTL8168C/8111C PCI-E
Gigabit Ethernet NIC
18
Standard Universal PCI to USB Host
Controller
19
PCI standard PCI-to-PCI bridge
19
Realtek RTL8168C/8111C PCI-E
Gigabit Ethernet NIC #2
19
Standard Universal PCI to USB Host
Controller
23
Standard Universal PCI to USB Host
Controller
23
Standard Universal PCI to USB Host
Controller
Table B-6: IRQ Lines APIC Mode
Note (1): These IRQs can be used for PCI devices when onboard
device is disabled. If IRQ is from ISA, user must reserve IRQ for ISA in
BIOS setup menu.
70
System Resources
MI-110
B.6 PCI Configuration Space Map
Bus #
Device # Function # Routing
Description
00
00
00
Internal
Intel Host Bridge
00
02
00
Internal
Intel VGA-compatible Controller
00
02
01
Internal
Intel Other Display Controller
00
1B
00
Internal
Unknown Device
00
1C
00
Internal
Intel PCI-to-PCI Bridge
00
1C
02
Internal
Intel PCI-to-PCI Bridge
00
1C
03
Internal
Intel PCI-to-PCI Bridge
00
1D
00
Internal
Intel UHCI USB Controller
00
1D
01
Internal
Intel UHCI USB Controller
00
1D
02
Internal
Intel UHCI USB Controller
00
1D
03
Internal
Intel UHCI USB Controller
00
1D
07
Internal
Intel USB v2.0 Controller
00
1E
00
Internal
Intel Subtractive Decode P2P Bridge
00
1F
00
Internal
Intel ISA Bridge
00
1F
02
Internal
Intel IDE Controller
00
1F
03
Internal
Intel SMBus Device
02
00
00
Internal
Realtek Ethernet Controller
03
00
00
Internal
Realtek Ethernet Controller
Table B-7: PCI Configuration Space Map
System Resources
71
B.7 PCI Interrupt Routing Map
INT Line
INT1
Intel VGA compatible Controller
X
Intel Multimedia device
X
Intel PCI-to-PCI Bridge
X
INT2
Intel PCI-to-PCI Bridge
INT3
X
Intel PCI-to-PCI Bridge
Intel UHCI USB Controller
X
X
Intel UHCI USB Controller
X
Intel UHCI USB Controller
X
Intel UHCI USB Controller
Intel USB v2.0 Controller
INT4
X
X
Intel IDE Controller
X
Intel SMBus Device
X
Realtek Ethernet Controller
X
Realtek Ethernet Controller
X
Table B-8: PCI Interrupt Routing Map
72
System Resources
MI-110
Important Safety Instructions
For user safety, please read and follow all instructions,
WARNINGS, CAUTIONS, and NOTES marked in this manual
and on the associated equipment before handling/operating the
equipment.
X
Read these safety instructions carefully.
X
Keep this user’s manual for future reference.
X
Read the specifications section of this manual for detailed
information on the operating environment of this equipment.
X
When installing/mounting or uninstalling/removing
equipment:
Z
X
Turn off power and unplug any power cords/cables.
To avoid electrical shock and/or damage to equipment:
Z
Keep equipment away from water or liquid sources;
Z
Keep equipment away from high heat or high humidity;
Z
Keep equipment properly ventilated (do not block or
cover ventilation openings);
Z
Make sure to use recommended voltage and power
source settings;
Z
Always install and operate equipment near an easily
accessible electrical socket-outlet;
Z
Secure the power cord (do not place any object on/over
the power cord);
Z
Only install/attach and operate equipment on stable
surfaces and/or recommended mountings; and,
Z
If the equipment will not be used for long periods of time,
turn off and unplug the equipment from its power source.
Important Safety Instructions
73
X
Never attempt to fix the equipment. Equipment should only
be serviced by qualified personnel.
A Lithium-type battery may be provided for uninterrupted, backup
or emergency power.
WARNING:
X
74
Risk of explosion if battery is replaced with one of an incorrect
type. Dispose of used batteries appropriately.
Equipment must be serviced by authorized technicians
when:
Z
The power cord or plug is damaged;
Z
Liquid has penetrated the equipment;
Z
It has been exposed to high humidity/moisture;
Z
It is not functioning or does not function according to the
user’s manual;
Z
It has been dropped and/or damaged; and/or,
Z
It has an obvious sign of breakage.
Important Safety Instructions
MI-110
Getting Service
Contact us should you require any service or assistance.
ADLINK Technology Inc.
Address: 9F, No.166 Jian Yi Road, Chungho City,
Taipei County 235, Taiwan
‫ק؀‬ᗼխࡉؑ৬ԫሁ 166 ᇆ 9 ᑔ
Tel:
+886-2-8226-5877
Fax:
+886-2-8226-5717
Email:
service@adlinktech.com
Ampro ADLINK Technology Inc.
Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA
Tel:
+1-408-360-0200
Toll Free: +1-800-966-5200 (USA only)
Fax:
+1-408-360-0222
Email:
info@adlinktech.com
ADLINK Technology Beijing
Address: ࣫ҀᏖ⍋⎔ऎϞഄϰ䏃 1 োⲜ߯ࡼ࡯໻ॺ E ᑻ 801 ᅸ
(100085)
Rm. 801, Power Creative E, No. 1, B/D
Shang Di East Rd., Beijing 100085, China
Tel:
+86-10-5885-8666
Fax:
+86-10-5885-8625
Email:
market@adlinktech.com
ADLINK Technology Shanghai
Address: Ϟ⍋Ꮦⓩ⊇⋒催⾥ᡔᓔথऎ䩺∳䏃 333 ো 39 ᐶ 4 ሖ
(200233)
Tel:
+86-21-6495-5210
Fax:
+86-21-5450-0414
Email:
market@adlinktech.com
ADLINK Technology Shenzhen
Address: ⏅ഇᏖफቅऎ⾥ᡔುफऎ催ᮄफϗ䘧᭄ᄫᡔᴃು
A1 ᷟ 2 ὐ C ऎ (518057)
2F, C Block, Bld. A1, Cyber-Tech Zone,
Gao Xin Ave. Sec 7, High-Tech Industrial Park S.,
Shenzhen, 518054 China
Tel:
+86-755-2643-4858
Fax:
+86-755-2664-6353
Email:
market@adlinktech.com
Getting Service
75
ADLINK Technology Inc. (German Liaison Office)
Address: Nord Carree 3, 40477 Duesseldorf, Germany
Tel:
+49-211-495-5552
Fax:
+49-211-495-5557
Email:
emea@adlinktech.com
ADLINK (French Liaison Office)
Address: 15 rue Emile Baudot, 91300 MASSY Cedex, France
Tel:
+33 (0) 1 60 12 35 66
Fax:
+33 (0) 1 60 12 35 66
Email:
france@adlinktech.com
ADLINK Technology Japan Corporation
Address: 151-0072 ᧲੩ㇺᷦ⼱඙ᐈ䊱⼱㩷
1-1-2 ᦺᣣ↢๮ᐈ䊱⼱䊎䊦 8F
Asahiseimei Hatagaya Bldg. 8F
1-1-2 Hatagaya, Shibuya-ku, Tokyo 151-0072, Japan
Tel:
+81-3-4455-3722
Fax:
+81-3-5333-6040
Email:
japan@adlinktech.com
ADLINK Technology Inc. (Korean Liaison Office)
Address: 昢殾柢 昢爎割 昢爎壟 1506-25 穢壊 B/D 2 猻
2F, Hando B/D, 1506-25, Seocho-Dong,
Seocho-Gu, Seoul, 137-070, Korea
Tel:
+82-2-2057-0565
Fax:
+82-2-2057-0563
Email:
korea@adlinktech.com
ADLINK Technology Singapore Pte Ltd.
Address: 84 Genting Lane #07-02A, Cityneon Design Centre,
Singapore 349584
Tel:
+65-6844-2261
Fax:
+65-6844-2263
Email:
singapore@adlinktech.com
ADLINK Technology Singapore Pte Ltd. (Indian Liaison Office)
Address: No. 1357, "Anupama", Sri Aurobindo Marg, 9th Cross,
JP Nagar Phase I, Bangalore - 560078, India
Tel:
+91-80-65605817
Fax:
+91-80-22443548
Email:
india@adlinktech.com
76
Getting Service