Mayones Electric Guitar User`s manual

Thank you for purchasing an electric bass of our production. We are convinced that you have made
a good choice and that your new instrument will help you in developing your musical talent. We would
like to help you in achieving this goal. This is why we would like you to familiarise yourself with a number
of maintenance rules.
Maintenance and operation.
Use only good quality strings, preferably from a single set. For bass guitar strings, it is especially
important to choose the correct scale length. Only the sets of strings with the scale length
corresponding to your instrument should be bought.
The way you wind the strings around the tuning keys is crucial for the instrument to stay in tune.
Remember to read the chapter explaining this procedure.
In order to work correctly, the bridge has to be correctly adjusted . It is the bridge that determines
if the instrument is tuned well. It also determines the overall comfort of playing.
Setting up the proper neck relief and the action of the strings is very important to achieve good
comfort of playing. These procedures need to be performed each time the gauge of the strings
is changed.
In order for a string to hold its pitch well, its intonation has to be adjusted. A separate chapter
is devoted to this procedure.
It is recommended to change the strings after 50-70 hours of operation. After this period most
strings tend to lose their bright sound and stop holding their pitch.
It is advised to clean the instrument, particularly the strings, after each period of playing it. Suitable
products are available in good music shops.
When transporting the instrument, a gig bag or a hardshell case should be used in order to
prevent damage caused by mechanical shock or the temperature change.
A guitar is a delicate instrument. The finish is vulnerable to scratches, fractures and even chipping.
Take good care of your instrument and use it according to the goal it was built for.
Protect your instrument from low and high temperature, and also from humidity.
Do not expose the instrument to direct sunlight for long periods of time. Do not leave your instrument
close to heating devices, nor in a car on a hot day.
Avoid sudden changes of temperature or humidity. In winter, after bringing a chilled instrument
into a heated room, leave it for a few hours in its case, until it has returned to room temperature.
Clean the strings and lacquer surfaces with a dry, delicate cotton cloth. For thorough cleaning, use
only specialized products (Guitar Polish and String Cleaner). Instruments with natural finish should
be conserved with special products based on natural oils.
Make sure all parts of the instrument are cleaned regularly.
Attention: Disregard of the above rules may result in loss of warranty.
Electric Bass Guitar User’s Manual
Main parts
of the bass guitar
1. headstock
2. logo
3. tuning mechanics
4. truss rod adjustment screw (plate)
5. nut
6. strings
7. fingerboard
8. frets
9. markers
10. neck joint
11. bolt
12. volume knob
13. balance knob
14. active EQ - bass knob
15. active EQ - treble knob
16. output jack
17. front strap button
18. neck pickup
19. pickup height adjustment screws
20. bridge pickup
21. bridge
22. bridge saddles
23. string
24. rear strap button
25. electronic compartment plate
26. battery compartment
Electric Bass Guitar User’s Manual
Winding the strings on tuning keys
Depending on the construction of the bridge, install the ball
in the slot of the bridge, pull the string through the hole in
the body, or install the ball in its proper place in the bridge.
The ball should hold tightly to the slot in the bridge, and its
axis should be perpendicular to the axis of the slot. If the
string fails to completely go through the slot (if it is blocked
by the thick part of the winding by the ball), check the size
of the slot and the quality of the winding. If the winding is
too thick, it is possible to slightly unwind it. Another solution is using strings that are unwound next
to the ball.
Next, stretch the string and cut it more or less 10cm behind the tuning key’s post. The headstock side
of the string is often finished with loosened winding and a plastic thread, which ensures the string’s
stability on the tuning key. One should not cut this part of the string off entirely, except for situations
when the string is obviously too long (e.g. When the tuning keys are in a 2+2 or 3+1 combination.)
Insert the end of the string
in the opening in the slot of
the tuning key (older type) or
simply in the slot (newer
type). You can bend the last
1-2 cm of the string by 90 degrees. Next, paying attention
for the string to cling tightly
to the edge of the slot, wind
the string on the key in the way that it clings to the key’s surface. The following windings should be
placed lower than the original. They should cling to each other, but the string should not cross itself.
All the strings should be wound in the same way (on single-sided headstocks) which facilitates tuning
the instrument.
The table below shows the commonly used scale types. Simply put, the scale of a string is the part
of the string between the nut and the bridge saddle.
The scale
Extra Long Scale
Long Scale Plus
Long Scale (Standard)
Medium Scale
Short Scale
35 ~ 36”
34 ~ 35”
32 ~ 33”
30 ~ 31”
The length of the wound string
(889 ~ 915 mm)
(864 ~ 889 mm)
(864 mm)
(813 ~ 838 mm)
(762 ~ 787 mm)
(~965 mm)
(~965 mm)
(~927 mm)
(~876 mm)
(~826 mm)
Electric Bass Guitar User’s Manual
Buying a set of strings of shorter scale may result in the plastic thread going beyond the nut, or in
strings being too short to install in the tuning key. Buying a set which is too long may result in a lot of
trouble with installing them, because the string may still be too thick at the key.
Attention: the best tone will be achieved by exchanging the whole set of strings. It is recommended
to change the strings after 50-70 hours of operation. After this period most strings tend to lose their
bright sound and stop to hold the pitch well.
Neck relief
Setting up a proper neck relief is achieved by loosening or tightening the truss rod which is built in
the axis of the neck. The truss rod adjustment screw is placed either in an opening next to the nut or at
the heel of the neck. We check the neck relief by fretting the string on the first and last fret simultaneously.
With the relief set up correctly, the height of the string above the 8th fret should measure about 0,5 mm.
If the string is higher (concave neck), one should tighten the adjustment screw.
If the string is lower (convex neck), one should loosen the adjustment screw.
last fret
first fret
8 fret
The Allen wrench’s movement should be gradual and delicate. After each turn of the key, never
greater than 90 degrees, check the height of the string above the 8th fret and the string fretted at the
first and last fret.
The 5- and 6-string basses’ necks often have two independent truss rods. They help in precisely
setting up the relief, however the procedure should be performed very carefully. It is important to pay
attention on gradual tightening and loosening both truss rods in order to achieve the same relief for all
the strings.
Attention: this procedure needs to be performed each time the strings are changed.
Electric Bass Guitar User’s Manual
Adjusting the bridge - string action
After installing the strings, tuning the instrument initially,
and setting up the neck relief, we can adjust their strings’
height over the frets.
The height of each saddle is usually set up by adjusting
two, three or four screws at the sides of the saddle (A). Many
saddles are equipped with a screw (B) which locks their
position and prevents them from falling off during string
change or in case of a string breaking. This screw should be
loosened before changing the position of such a saddle (this
is also important when adjusting intonation).
The saddles should be positioned in a slight curve - the
difference between the inner and outer saddles should be
close to 1 mm. This is caused by the necessity of the saddles
to follow the radius of the fingerboard.
The height of the string over the 12th fret depends on
personal preferences of the musician. A standard string
action for a 4-string bass is: 2.5 mm for the G1 string and 3.5
mm for the E4 string.
Setting the action too low results in strings buzzing against
the frets and shorter sustain. Setting the action too high
results in a decrease in comfort of playing. It also causes
strings not to intonate properly because of the added tension
during fretting.
The suggested height of the strings over the frets
highest string
lowest string
4-string basses
2.0 mm (5/64")
2.8 mm (7/64")
5- and 6-string basses
2.0 mm (5/64")
3.2 mm (1/8")
Some bridges also allow to adjust the distance between
adjacent strings. This distance should be identical between
each string and the outer strings should be set far enough
from the edges of the fingerboard not to slip away from it
during playing.
Before changing the string spacing, loosen the screw (C)
locking the upper piece of the saddle. In some types of
bridges, the string spacing adjustment is achieved by moving
the entire saddle (e.g. Schaller 2000).
Electric Bass Guitar User’s Manual
Stabilising the tuning
After each string has been changed, after tuning it to the desired pitch,
hold it with your fingers above the 12th fret and pull it 1cm away from the
fretboard for around 10 seconds. Retune the string and repeat this procedure
until the last stretching will not cause a change in the pitch. After stabilising
the tuning, adjust the intonation.
Attention: an electronic chromatic tuner will greatly facilitate all the
procedures connected with tuning the instrument.
Adjusting intonation
Adjusting the intonation is crucial to eliminating the error in
the string pitch on certain frets. It consists of tuning the string
exactly to the desired pitch and then fine tuning its bridge saddle
to make the pitch at the 12th fret exactly an octave higher. If after
tuning a string the pitch on the 12th fret is too low, the saddle of
the bridge should be moved toward the front edge of the bridge
(the scale should be shortened). If after tuning a string the pitch
on the 12th fret is too high, the saddle of the bridge should be
moved toward the rear edge of the bridge (the scale should be
This action is usually repeated a few times in order to achieve
precise intonation. Retune the string after each repositioning of
its saddle. When the intonation is set up properly, the saddles
are usually positioned in a diagonal line. If they do not, or if the
range of regulation appears too small, the problem is the strings
being either too worn out or of bad quality. Because of different
types of bridges and saddles, the saddle adjustment is achieved
by different means.
Attention: retune the string after each repositioning of its
A - LOCK - an Allen screw locking the saddle’s position (when
the string’s intonation is set up correctly) Before changing the
saddle’s position, loosen the screw a bit to enable the saddle to
move freely.
Electric Bass Guitar User’s Manual
The height of the strings over the pickups
The distance between the pickups and the strings is an
important factor of the instrument’s sound. This distance
depends on the type of pickups and the type of strings used.
It is checked by fretting the string on the last fret and
measuring the distance between the surface of the pickup
and the surface of the string. A standard height of the string
over the bridge pickup for a 4-string bass is: 2.0 mm for the
G1 string and 2.2 mm for the E4 string. For the neck pickup:
2.4 for the G1 string and 3.2 for the E4 string. When adjusting
a 5- or 6-string bass - these heights should refer to the outer
strings. The height of the pickups is usually regulated by
adjusting the screws that attach them to the body of the
instrument. When the pickups are installed in the pickguard,
turning the screws clockwise will decrease the height and
turning them counter-clockwise will increase the height. When
the pickups are installed directly into the instrument’s body,
turning the screws clockwise will increase the height and turning them counter-clockwise will decrease
the height. If the distance between the pickups and strings is to small, it may cause the strings to hit the
pickups generating knocking or distorted sound. Pickups equipped with strong magnets may pull the
string and cause difficulties in tuning. On the other hand, if the distance is too big, the instrument’s
signal will be weak and lacking in character. The noise level will also increase. If a pickup is equipped
with adjustable pole pieces, it is possible to adjust the differences in volume between strings by
determining the height of each pole piece. Setting up the distance between strings and pickups is
a matter of personal preference and each musician should spend some time on finding the preferred
Battery replacement
If a bass is equipped with active electronics, a preamp, a piezo system, or LED
fret markers, they are usually powered by one or two 9V batteries. The
battery compartment (or compartments) are located on the back of
the instrument's body. Opening them does not require tools, however
caution is advised in order not to break the delicate lid. The compartment's construction prevents putting the battery in the wrong way. The
compartment is locked by gently pushing the lid back, which produces
a distinct click. An alkaline battery life is estimated for between 300 and 1000 hours
of usage. It is however advised to change it as soon as a considerable drop in output or distortion are
experienced. This will be noticeable at first when playing harder, or with boosted EQ knobs.
To prolong battery life, remove the cable from the output jack when not using your instrument.
Electric Bass Guitar User’s Manual
The Piezo System
Some bass guitars are equipped with Graph Tech saddles with built in piezo pickups. The pickup
signal is led to the instrument’s output jack after it has been amplified by a preamp powered by a single
9V battery. The preamp is located in the guitar’s control cavity and attached to the piezo/magnetic
signal mixing knob (Blender). The preamp enables adjusting the piezo pickup’s output level to the
output level of magnetic pickups (for the Blender’s centre setting).
It is achieved by adjusting a small PR-type control located on the
piezo system’s plate. Adjustment should be performed carefully, using
a small screwdriver or a similar tool. When shipped from the factory,
the piezo volume is set up to match the magnetic pickup’s volume.
It may require adjustment after changing strings or after changing
the height of the magnetic pickups under the strings.
Piezo pickups tend to carry much more high frequencies compared to magnetic pickups. In some
instances, this may lead to signal distortion. In order to rectify the problem, it is advised to either:
– decrease the piezo system’s output volume
– decrease the amplifier’s input gain or
– adjust its EQ.
Signal distortion may be also caused by an empty battery. In this case, the battery should be replaced
immediately, with attention to correct polarisation. The piezo system’s battery is located in a special
compartment placed at the back of the body, next to the control cavity. No tools are needed to open the
compartment. The guitar’s output jack also functions as a power switch. To prolong battery life, remove
the plug from the output jack when not using your instrument.
Given the fragility of the saddles’ construction and the fact
that they are linked to the electronics with thin wires, it is
advisable to use special caution while replacing strings and
intonation and action adjustments. Use of superfluous force
may cause damage to the piezo system.
Depending on pickup and electronics’ configuration, there
are a few different ways of controlling both piezo and magnetic
The piezo system is usually turned on by raising one of
the knobs (push-pull) or with the help of an extra mini-switch.
To prolong battery life, remove the cable from the output
jack when not using your instrument.
Electric Bass Guitar User’s Manual
Apart from traditional bass guitar electronics system – passive pickups and tone knobs, Mayones
bass guitars may be equipped with active pickups and/or a preamp with an active tone control. Depending
on the solution used, active tone control enables the player to independently cut or boost low, mid and
high frequencies of the sound. There are numerous options for the pickups and electronics’ package.
An extra piezo pickup may result in the instrument’s tone to be shaped by a series of knobs and miniswitches. Some of the most common solutions for passive and active systems are presented below.
passive control
Aguilar OBP-1
Bartolini HR-3.4
Bartolini HR-4.6
Aguilar OBP-3SK
Aguilar OBP-3TK
Aguilar OBP-3SK/PP
Aguilar OBP-3SK + Coils Spliting
Aguilar OBP-3SK + Piezo
- 10 -
volume knob
blend knob
passive tone knob
active EQ - bass knob
active EQ - mid knob
active EQ - treble knob
bridge pickup
neck pickup
- a knob that can be raised and lowered
thus activating a DPDT type switch. It can act as an
active/passive switch, midrange bandwidth selector, coil
splitter etc.
Active/Passive - an extra option enabling the player to turn
the active preamp on or off.
Piezo Blender - piezo/magnetic signal blend knob.
Coil splitter
- turns one of the pickup’s coils off.
Electric Bass Guitar User’s Manual
In order to preserve the aesthetic look and good technical shape,
the instrument should be regularly cleaned and maintained.
An instrument should be thoroughly cleaned after each playing
session - especially the neck, strings and body. Attention should
be given to wiping all sweat residue, which is the main cause of
string and metal parts’ corrosion. It also decreases the gloss of the
finish. The best tool for wiping the sweat residue is a soft, dry cloth.
As an option, some types of specifically formulated polish can be
used, respectably for finished, not finished and metal parts. These
products should be handled with caution and their usefulness should
be first checked on a small, less visible piece of surface. Products
based on acids, alkalis, benzene, gasoline, alcohols, solvents and
strong detergents, should not be used. We advise thorough cleaning
and maintenance during each string change.
Natural (wax and oil) finishes require different kinds of attention. Delicate cloths can be used for
cleaning, but maintaining the the finish is achieved by using a specifically formulated polish based on
natural oils. When using them, be sure to act according to the instructions on their containers.
Rosewood, ebony and other types of exotic wood occasionally require impregnating. The need for
such an operation may be indicated by the wood looking more pale and mat. In order to facilitate
impregnating, it is recommended to remove the strings and to wipe the fretboard with a soft brush.
Next, after soaking a cloth with Lemon Oil (Fretboard Conditioner) rub it in the fretboard. This procedure
should be repeated a few times with hour-long intervals. In the end, wipe the residue off with a dry
Other options
Due to the restricted volume of this User’s Manual, an array of other options and technical solutions
was not mentioned here. Among these are: Hipshot D-tuners, different bridge constructions, LED fret
markers, or sophisticated electronics packages. If you encounter problems with your instrument, visit
our technical support page at, or contact us via email.
Electric Bass Guitar User’s Manual
- 11 -
You will find more information on guitar operation and maintenance and solving basic problems on our website
Mayones Guitars and Basses care constantly about the quality of their instruments and release their newer and
upgraded versions, as well as search for the best possible building materials.
All parts of the instruments are RoHS compliant.
The company reserves the right to make changes without prior notice.
Mayones and the Mayones logo are registered trade-marks of Gitary Mayones s.c.
Gitary Mayones s.c.
ul. Narwicka 10
80-557 Gdansk, Poland
tel. +48 58 343 07 83
fax +48 58 343 04 35
© Gitary Mayones 2008