advertisement
Electric Single Wall Oven
E30EW75GPS professional series
Wave-Touch ® Controls
Sleek control panel illuminates with just a touch – giving you more control over your cooking – and fades away to an uncluttered display after an option is selected.
Smooth-Glide ® Oven Racks
Ball bearing oven racks glide with unparalled ease and extend fully for effortless access.
CustomConvect
3
™
Technology
Convection
Distributes heat evenly throughout the oven by adding a third cooking element plus a variable speed fan.
Cool-Touch ™ Oven Door
Beautiful all-glass door allows you to see what’s inside and is cool to the touch and easy to clean.
30" ELECTRIC SINGLE WALL OVEN
OVEN FEATURES
Oven Cavity
Cobalt Blue Interior
CustomConvect
3
™ Convection System
Hidden Bake Element
Convection Conversion
Preheat Control
Keep Warm
Light Clean / Heavy Clean
Self-Cleaning with Auto-Safety Latch ™
Self-Cleaning Cycle
Self-Cleaning Rack Removal Alert
Dual Radiant ™ Baking System
Eight-Pass Broil & Radiant Bake Element
Smooth-Glide ® Oven Racks
Standard Racks
Theatre Lighting
Porcelain Broiler Pan with Grill
Yes
3
1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
4.2 Cu. Ft.
Yes
Yes
Yes
CONTROL PANEL FEATURES
Electronic Oven Control
Electronic Clock / Timer
Electronic Temperature Display
Glass Wave-Touch ® Control with Blue LED Display
Automatic Oven – Delay, Cook & Off
Electronic Lockout
“My Favorite” Settings
Custom-Set ™ Options with Temperature Probe
Automatic Oven Shutoff – 12 Hour
Auto Set ™ Control – Convection
Programmable for °F or °C
Integrated Halogen Oven Light – Touch Pad
DOOR STYLE
Cool-Touch ™ Oven Door
Removable Door
Extra-Large Window
Stainless Door Handle / Towel Bar
ADDITIONAL FEATURES
Sabbath Mode (Star-K ® Certified)
A.D.A. Compliant*
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
SPECIFICATIONS
Oven Cavity Dimensions –
Height
Width
Depth
Overall Exterior Dimensions –
Height
Width
Depth (Including Door)
(with 90° Door Open)
Power Supply Location
Approved for Under-Counter Installation**
Amps @ 240 / 208 Volts
Connected Load (kW Rating) @ 240 / 208 Volts
Bake Element (Watts @ 240 / 208 Volts)
Broil Element (Watts @ 240 / 208 Volts)
Armored Electrical Cable
Shipping Weight (Approx.)
16-1/2"
24-1/8"
18-1/32"
29-1/4"
30"
24-5/8"
47-7/8"
Left Bottom Rear
Yes
16.6 / 14.4
4.0 / 3.0
2200
4000
Included
196 Lbs.
* When properly installed, meets the appliance standards in the Americans with Disabilities
Act and the Architectural Barriers Act Accessibility Guidelines as published by the United
States Access Board on June 23, 2004, as amended August 5, 2005.
**Single Wall Oven is approved to be used beneath Electrolux ICON ® gas cooktop models
E36GC70FSS and E30GC70FSS; and Electrolux ICON ® electric cooktop models
E36IC75FSS, E30IC75FSS, E36IC80ISS, E30IC80ISS, E36EC70FSS and E30EC70FSS.
Gas and electric cooktop models NOT approved for use in this installation are
E36GC75GSS, E36EC75ESS, E36EC75HSS, E36GC76GPS, E30GC74GPS, E48GC76EPS,
E30EC65ESS and E36EC65ESS.
NOTE: Always consult local and national electric codes. Refer to Product Installation Guide for detailed installation instructions on the web at electroluxicon.com.
Specifications subject to change.
electroluxicon.com
Electric Single Wall Oven
E30EW75GPS professional series
7 /
8
"
29
1
/
4
"
30"
Allow at least
23 1 /
4
" clearance for door depth when open
30" min.
1 1 /
2
" min.
28 1 /
4
"
Spacer
27
7
/
8
"
28 1 /
2
" min.
28
7
/
8
" max.
28 1 /
2
" min.
29" max.
24" min.*
(critical
dimension)
4" x 4" opening to route armoured cable
Full base required to support
200 lbs.
24 5 /
8
"
4
31" suggested distance
1 /
2
" min.
required
3"
2" min.
Bottom cutout edge must be finish cut
Electrical junction box location
*Critical dimension –
MUST be applied
30" Electric Single Wall Oven Specifications
•
Product Weight – 178 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt,
60 Hertz AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
Always consult local and national electric codes.
•
Minimum 23-1/4" clearance for oven door depth when open.
•
Suggested distance from floor is 31". Minimum required distance is 4-1/2".
•
Minimum 24" deep cutout dimension is critical for proper installation, to ensure that oven’s faceplate will fit flush against cabinet front.
•
Full oven base of solid plywood or similar material required, capable of supporting 200 Lbs.
•
Base must be level and cabinet front must be square with finish-cut bottom edge.
•
Single Wall Oven is NOT approved to be used in stackable or side-by-side installation.
•
Single Wall Oven is approved to be used alone in under-counter installation or beneath Electrolux ICON ® gas cooktop models
E36GC70FSS and E30GC70FSS; and Electrolux ICON ® electric cooktop models E36IC75FSS, E30IC75FSS, E36IC80ISS, E30IC80ISS,
E36EC70FSS and E30EC70FSS. (Refer to Gas or Electric Cooktop
Installation Over 30" Electric Single Wall Oven Specifications pages on web.)
Gas and electric cooktop models NOT approved for use in this installation are E36GC75GSS, E36EC75ESS, E36EC75HSS, E48GC76EPS,
E36GC76GPS, E30GC74GPS, E30EC65ESS and E36EC65ESS.
•
Single Wall Oven is approved to be used in combination with any
Electrolux ICON ® Warmer Drawer. (Refer to model-specific Warmer
Drawer product page for Combination Installation Specifications.)
•
Single Wall Oven is approved to be used in combination with any
Electrolux ICON ® High-Speed Oven or Built-In Microwave. (Refer
to model-specific Combination Installation Specifications pages on web.)
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
E30EW75GPS 04/11 © 2011 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
General Installation Guidelines
with Counter-Depth French Door Refrigerator
Use these dimensions and clearance instructions for planning purposes only. For detailed installation instructions, refer to installation guide, packed with product, or on the web at electroluxicon.com.
Front
Top
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
INSTGDLNS_FDR EI 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
General Installation Guidelines
with Counter-Depth Side-by-Side Refrigerator
Use these dimensions and clearance instructions for planning purposes only. For detailed installation instructions, refer to installation guide, packed with product, or on the web at electroluxicon.com.
Front
Top
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
INSTGDLNS_SSR EI 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
30" Combination Installation –
Built-In Microwave/Single Wall Oven
For detailed product dimensions and installation specifications, refer to model-specific product page and installation guide on web
24" min.
30" Built-In
Microwave Cutout
For models:
E30MO75HPS
E30MO75HSS
2"
(visible
gap)*
21" min.
21 1 /
2
" max.
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
28
28
7
1
/
2
" min.
/
8
" max.
* Minimum 2
1
/
8
" clearance required from bottom of
Built-In Microwave cutout to top edge of
Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates.
** Critical dimension –
MUST be applied
4
31" suggested distance
1
/
2
" min.
required
28 1 /
2
" min.
29" max.
28 1 /
2
" min.
29" max.
4"
30 1 /
8
" min.
6"
18"
120V/60 Hz grounded electrical outlet should NOT be located within shaded area
Full plywood base required to support
150 lbs.
CL
24" min.**
(critical
dimension)
4"x 4" opening to route armored cable
Full base required to support 200 lbs.
2" min.
Bottom cutout edge must be finish cut
3" max.
Electrical junction box location
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
•
Minimum 24" deep cutout dimension is critical for proper combination installation, to ensure that each built-in product’s faceplate will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of Wall Oven cutout to floor, 31" suggested.
•
Respect critical dimensions as noted for proper installation of built-In products.
•
Minimum 23-1/4" clearance needed for Wall Oven door depth when open.
30" Built-In Convection Microwave Specifications
•
Product Weight – (E30MO75HPS / E30MO75HSS) 84 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.6 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120 Volts = 13.7 Amps
•
Full oven base of solid plywood or similar material required, capable of supporting 150 Lbs.
•
Minimum 2-1/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
Full oven base of solid plywood or similar material required, capable of supporting 200 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
MODD_EW INST 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
Gas Cooktop Installation
Over 30"Electric Single Wall Oven
For all approved gas cooktop models, a minimum height opening of 6-1/2" (from top of counter) required in right cabinet side panel and/or filler panel, to route gas and electric hookups. (Refer to Gas Cooktop
Utility Hookup Diagram)
Side filler panels necessary to isolate oven from adjoining cabinets. Panel height may need to be modified to accommodate the depth of approved gas cooktop models
Electric Single Wall Oven Cutout
For models: E30EW75GPS
& E30EW75GSS
Cooktop
cutout**
120V/60Hz grounded outlet, for gas cooktop
Approx. 3"
240 /208V
Junction box for wall oven
24" min.*
28 1 /
2
" min.
29" max.
Cooktop
18" max.
Countertop
Manifold pipe
Flare union
Flexible connector
6 1 /
2
" min.
Pressure regulator
Cabinet sides and/or filler panel
5"
4"
Gas
Cooktop
Utility
Hookup
Flare union
120V/60Hz grounded outlet
Manual shutoff valve
(Must be accessible)
Side View
Cooktop
Oven cutout
36" min.
28
28
1 /
2
" min.
7 /
8
" max.
Wall Oven
24" min.
cutout depth
4-1/2" maximum height allowed from oven base to floor if cooktop is installed directly over wall oven.
(5" maximum height allowed with no cooktop.)
Install 3 /
4
" full plywood base on 2 runners, flush with toe plate, capable of supporting 200 lbs.
Unit will overlap cutout (minimum) edges by 1"
To route armored cable to junction box through left cabinet side panel and/or filler panel, cut minimum 4" x 4" opening in wood base and runner
*Critical dimension – MUST be applied
**For cooktop cutout dimensions refer to model-specific product page or installation guide on web
30" Electric Single Wall Oven Under-Counter
Installation Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
Always consult local and national electric and gas codes.
•
Minimum 23-1/4" clearance for oven door depth when open.
•
Minimum 24" deep cutout dimension is critical for proper installation, to ensure that oven’s faceplate will fit flush against cabinet front.
•
Full oven base of solid plywood or similar material required, capable of supporting 200 Lbs. Install over two runners and flush with toe plate.
•
Base must be level and cabinet front must be square with finish-cut bottom edge.
•
Side filler panels necessary to isolate oven from adjoining cabinets.
•
Allow 5" maximum height from oven base to floor, if NO cooktop is installed directly over wall oven.
Gas Cooktop Installation
Over 30" Electric Single Wall Oven Specifications
Electrolux ICON ® Single Wall Oven models E30EW75GPS and
E30EW75GSS are approved to be used beneath Electrolux ICON ® gas cooktop models E36GC70FSS and E30GC70FSS (gas cooktop
models NOT approved for use in this installation are E36GC75GSS,
E48GC76EPS, E36GC76GPS and E30GC74GPS).
For detailed Gas Cooktop installation, refer to model-specific product page and installation guide on web.
•
Side filler panels necessary to isolate oven from adjoining cabinets.
Panel height may need to be modified to accommodate the depth of approved gas cooktop models.
•
•
Minimum height opening of 6-1/2" (from top of counter) required in right cabinet side panel and/or filler panel, to route gas and electric hookups.
Allow 4-1/2" maximum height from oven base to floor, if cooktop is installed directly over wall oven.
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
GC_EW INST 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
30" Combination Installation –
Built-In Microwave/Single Wall Oven
For detailed product dimensions and installation specifications, refer to model-specific product page and installation guide on web
24" min.
30" min.
30" Built-In
Microwave Cutout
For model:
E30MO65GSS
2"
(visible
gap)*
19 7
20 3
/
8
" min.
/
8
" max.
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
28
28 7
1 /
2
" min.
/
8
" max.
26 1 /
2
" min.
27" max.
28 1 /
2
" min.
29" max.
5"
11
1
24" min.**
(critical
dimension)
/
2
"
* Minimum 3
1
/
8
" clearance required from bottom of
Built-In Microwave cutout to top edge of
Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates
** Critical dimension –
MUST be applied
31" suggested distance
4 1 /
2
" min.
required
2" min.
Bottom cutout edge must be finish cut
120V/60 Hz grounded electrical outlet should NOT be located within shaded area
Full plywood base required to support
100 lbs.
4"x 4" opening to route armored cable
Full base required to support 200 lbs.
3" max.
Electrical junction box location
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
•
Minimum 24" deep cutout dimension is critical for proper combination installation, to ensure that each built-in product’s faceplate will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of Wall Oven cutout to floor, 31" suggested.
•
Respect critical dimensions as noted for proper installation of built-In products.
•
Minimum 23-1/4" clearance needed for Wall Oven door depth when open.
30" Built-In Convection Microwave Specifications
•
Product Weight – 60 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.55 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120 Volts = 13 Amps
•
Consult local building code in the event that cutout opening may be required to be enclosed with sides, ceiling and rear partition.
•
Full oven base of solid plywood or similar material required, capable of supporting 100 Lbs.
•
Minimum 3-1/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
Full oven base of solid plywood or similar material required, capable of supporting 200 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
MO_EW INST 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
Electric Cooktop Installation
Over 30"Electric Single Wall Oven
For all approved electric cooktop models, cut minimum
4" x 4" opening in right cabinet side panel and/or filler panel, to route armoured cable to junction box
Side filler panels necessary to isolate oven from adjoining cabinets. Panel height may need to be modified to accommodate the depth of approved electric cooktop models
For models: E30EW75GPS
& E30EW75GSS
Cooktop
cutout**
Approx. 3"
240 /208V
Junction box for electric cooktop
Approx. 3"
240 /208V
Junction box for wall oven
24" min.*
Oven cutout
36" min.
28
28 7
1 /
2
" min.
/
8
" max.
28 1 /
2
" min.
29" max.
24" min.
cutout depth
4-1/2" maximum height allowed from oven base to floor if cooktop is installed directly over wall oven.
(5" maximum height allowed with no cooktop.)
Install 3 /
4
" full plywood base on 2 runners, flush with toe plate, capable of supporting 200 lbs.
Unit will overlap cutout (minimum) edges by 1"
To route armored cable to junction box through left cabinet side panel and/or filler panel, cut minimum 4" x 4" opening in wood base and runner
*Critical dimension – MUST be applied
**For cooktop cutout dimensions refer to model-specific product page or installation guide on web
30" Electric Single Wall Oven Under-Counter
Installation Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
Always consult local and national electric codes.
•
Minimum 23-1/4" clearance for oven door depth when open.
•
Minimum 24" deep cutout dimension is critical for proper installation, to ensure that oven’s faceplate will fit flush against cabinet front.
•
Full oven base of solid plywood or similar material required, capable of supporting 200 Lbs. Install over two runners and flush with toe plate.
•
Base must be level and cabinet front must be square with finish-cut bottom edge.
•
Side filler panels necessary to isolate oven from adjoining cabinets.
•
Allow 5" maximum height from oven base to floor, if NO cooktop is installed directly over wall oven.
Electric Cooktop Installation Over
30" Electric Single Wall Oven Specifications
Electrolux ICON ® Single Wall Oven models E30EW75GPS and
E30EW75GSS are approved to be used beneath Electrolux ICON ® electric cooktop models E36IC80ISS, E30IC80ISS, E36EC70FSS and
E30EC70FSS (electric cooktop models NOT approved for use in this
installation are E36EC75HSS, E30EC65ESS and E36EC65ESS).
For detailed Electric Cooktop installation, refer to model-specific product page and installation guide on web.
•
Side filler panels necessary to isolate oven from adjoining cabinets.
Panel height may need to be modified to accommodate the depth of approved electric cooktop models.
•
To route armored cable to junction box, cut minimum 4" x 4" opening in right cabinet side panel.
•
Allow 4-1/2" maximum height from oven base to floor, if cooktop is installed directly over wall oven.
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
EC_EW INST 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
30" Combination Installation –
High-Speed Oven/Single Wall Oven
For detailed product dimensions and installation specifications, refer to model-specific product page and installation guide on web
24" min.
30" High-Speed
Oven Cutout
For models:
E30SO75FPS
E30SO75ESS
2"
(visible
gap)*
21
22 3
11 /
16
" min.
/
16
" max.
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
28
28 7
1 /
2
" min.
/
8
" max.
22
22
3 /
8
" min.
7 /
8
" max.
28 1 /
2
" min.
29" max.
* Minimum 2
5
/
8
" clearance required from bottom of
Built-In High-Speed
Oven cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates
** Critical dimension –
MUST be applied
31" suggested distance
4 1 /
2
" min.
required
2" min.
Bottom cutout edge must be finish cut
30" min.
20 1 /
4
"
16 3 /
4
"
240V/60 Hz grounded electrical outlet should NOT be located within shaded area
Full plywood base required to support
150 lbs.
CL
4"x 4" opening to route armored cable
24" min.**
(critical
dimension)
Full base required to support 200 lbs.
3" max.
Electrical junction box location
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
•
Minimum 24" deep cutout dimension is critical for proper combination installation, to ensure that each built-in product’s faceplate will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of Wall Oven cutout to floor, 31" suggested.
•
Respect critical dimensions as noted for proper installation of built-In products.
•
Minimum 23-1/4" clearance needed for Wall Oven door depth when open.
30" High-Speed Oven Specifications
•
Product Weight – (E30SO75FPS / E30SO75ESS) 115 Lbs.
•
Voltage Rating – 240V / 60 Hz / 15 or 20 Amps
•
Single phase 3- or 4-wire cable, 240 Volt, 60 Hertz AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 Volts = 3.3 kW
•
Amps @ 240 Volts = 13.2 Amps
•
Full oven base of solid plywood or similar material required, capable of supporting 150 Lbs.
•
Minimum 2-5/8" clearance required from bottom of High-Speed Oven cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
Full oven base of solid plywood or similar material required, capable of supporting 200 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
SO_EW INST 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
30" Combination Installation –
Built-In Microwave/Single Wall Oven/Warmer Drawer
For detailed product dimensions and installation specifications, refer to model-specific product page and installation guide on web
24" min.
30" Built-In
Microwave Cutout
For models:
E30MO75HPS
E30MO75HSS
2"
(visible
gap)*
21" min.
21 1 /
2
" max.
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
28
28 7
1 /
2
" min.
/
8
" max.
30" Warmer
Drawer Cutout
For models:
E30WD75GPS
E30WD75GSS
E30WD75GTT
1 3 /
4
" min.
†
9
10
7 /
8
" min.
1 /
4
" max.
4 1 /
2
" min.
required
28
28
28
28
1
3
3
1
/
2
" min.
/
4
" max.
/
2
" min.
/
4
" max.
28
28
1
/
2
" min.
3
/
4
" max.
30 1 /
8
" min.
4"
CL
24" min.**
(critical
dimension)
6"
18"
120V/60 Hz grounded electrical outlet should NOT be located within shaded area
Full plywood base required to support
150 lbs.
Two 3" wide by 3 /
4
" thick planks must be installed, capable of supporting
200 lbs.
Bottom of oven cutout
11 5 /
8
" min.**
(critical dimension)
* Minimum 2 1 /
8
" clearance required from bottom of
Built-In Microwave cutout to top edge of
Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates.
** Critical dimension –
MUST be applied
†
Maximum height depends on critical dimension (11 5 /
8
")
††
Electrical junction box for Wall Oven must be lower than the Warmer Drawer cutout
Full plywood base required to support
100 lbs.
3" max.
††
Electrical junction box location
4"x 4" opening to route armored cable
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
•
Minimum 24" deep cutout dimension is critical for proper combination installation, to ensure that each built-in product’s faceplate will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of Warmer Drawer cutout to floor.
•
Respect critical dimensions as noted for proper installation of built-In products.
•
Minimum 23-1/4" clearance needed for Wall Oven door depth when open.
30" Built-In Convection Microwave Specifications
•
Product Weight – (E30MO75HPS / E30MO75HSS) 84 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.6 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120 Volts = 13.7 Amps
•
Full oven base of solid plywood or similar material required, capable of supporting 150 Lbs.
•
Minimum 2-1/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
To support Wall Oven, two 3"-wide x 3/4"-thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement.
30" Warmer Drawer Specifications
•
Product Weights – (E30WD75GPS / E30WD75GSS) 49 Lbs. /
(E30WD75GTT) 41 Lbs.
•
Voltage Rating – 120V / 450W / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 0.45 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120V = 3.75 Amps
•
Full base of solid plywood or similar material required, capable of supporting 100 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
MODD_EW_WD INST 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
30" Combination Installation –
Built-In Microwave /Single Wall Oven/Warmer Drawer
For detailed product dimensions and installation specifications, refer to model-specific product page and installation guide on web
24" min.
30" min.
30" Built-In
Microwave Cutout
For model:
E30MO65GSS
2"
(visible
gap)*
19
20
7 /
8
" min.
3 /
8
" max.
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
28
28 7
1 /
2
" min.
/
8
" max.
26
1
/
2
" min.
27" max.
28
28
1 /
2
" min.
3 /
4
" max.
30" Warmer
Drawer Cutout
For models:
E30WD75GPS
E30WD75GSS
E30WD75GTT
1 3 /
4
" min.
†
9
10 1
7 /
8
" min.
/
4
" max.
4 1 /
2
" min.
required
28
28
1
/
2
" min.
3
/
4
" max.
5"
11 1
24" min.**
(critical
dimension)
/
2
"
Full plywood base required to support
100 lbs.
3" max.
††
Electrical junction box location
4"x 4" opening to route armored cable
120V/60 Hz grounded electrical outlet should NOT be located within shaded area
Full plywood base required to support
100 lbs.
Two 3" wide by 3 /
4
" thick planks must be installed, capable of supporting
200 lbs.
Bottom of oven cutout
11 5 /
8
" min.**
(critical dimension)
* Minimum 3 1 /
8
" clearance required from bottom of
Built-In Microwave cutout to top edge of
Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates
** Critical dimension –
MUST be applied
†
Maximum height depends on critical dimension (11 5 /
8
")
††
Electrical junction box for Wall Oven must be lower than the Warmer Drawer cutout
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
•
Minimum 24" deep cutout dimension is critical for proper combination installation, to ensure that each built-in product’s faceplate will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of Warmer Drawer cutout to floor.
•
Respect critical dimensions as noted for proper installation of built-In products.
•
Minimum 23-1/4" clearance needed for Wall Oven door depth when open.
30" Built-In Convection Microwave Specifications
•
Product Weight – 60 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.55 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)
•
•
Amps @ 120 Volts = 13 Amps
Consult local building code in the event that cutout opening may be required to be enclosed with sides, ceiling and rear partition.
•
Full oven base of solid plywood or similar material required, capable of supporting 100 Lbs.
•
Minimum 3-1/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
To support Wall Oven, two 3"-wide x 3/4" thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement.
30" Warmer Drawer Specifications
•
Product Weights – (E30WD75GPS / E30WD75GSS) 49 Lbs. /
(E30WD75GTT) 41 Lbs.
•
Voltage Rating – 120V / 450W / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 0.45 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120V = 3.75 Amps
•
Full base of solid plywood or similar material required, capable of supporting 100 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
MO_EW_WD INST 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
30" Combination Installation –
High-Speed Oven/Single Wall Oven/Warmer Drawer
For detailed product dimensions and installation specifications, refer to model-specific product page and installation guide on web
24" min.
30" High-Speed
Oven Cutout
For Models:
E30SO75FPS
E30SO75ESS
2"
(visible
gap)*
21
22
3
11
/
16
" min.
/
16
" max.
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
28
28 7
1 /
/
8
2
" min.
" max.
30" Warmer
Drawer Cutout
For models:
E30WD75GPS
E30WD75GSS
E30WD75GTT
1 3 /
4
" min.
†
9
10
1
7
/
8
" min.
/
4
" max.
4
1
/
2
" min.
required
22
22
3 /
8
" min.
7 /
8
" max.
28
28
28
28
1
3
1
3
/
2
" min.
/
4
" max.
/
2
" min.
/
4
" max.
Full plywood base required to support
100 lbs.
30" min.
20
CL
1 /
4
"
24" min.**
(critical
dimension)
16 3 /
4
"
240V/60 Hz grounded electrical outlet should NOT be located within shaded area
Full plywood base required to support
150 lbs.
Two 3" wide by
3
/
4
" thick planks must be installed, capable of supporting
200 lbs.
Bottom of oven cutout
11 5 /
8
" min.**
(critical dimension)
* Minimum 2 5 /
8
" clearance required from bottom of
Built-In High-Speed
Oven cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates
** Critical dimension –
MUST be applied
†
Maximum height depends on critical dimension (11 5 /
8
")
††
Electrical junction box for Wall Oven must be lower than the Warmer Drawer cutout
3" max.
††
Electrical junction box location
4"x 4" opening to route armored cable
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
•
Minimum 24" deep cutout dimension is critical for proper combination installation, to ensure that each built-in product’s faceplate will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of Warmer Drawer cutout to floor.
•
Respect critical dimensions as noted for proper installation of built-In products.
•
Minimum 23-1/4" clearance needed for Wall Oven door depth when open.
30" High-Speed Oven Specifications
•
Product Weight – (E30SO75FPS / E30SO75ESS) 115 Lbs.
•
Voltage Rating – 240V / 60 Hz / 15 or 20 Amps
•
Single phase 3- or 4-wire cable, 240 Volt, 60 Hertz AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 Volts = 3.3 kW
•
Amps @ 240 Volts = 13.2 Amps
•
Full oven base of solid plywood or similar material required, capable of supporting 150 Lbs.
•
Minimum 2-5/8" clearance required from bottom of High-Speed Oven cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
To support Wall Oven, two 3"-wide x 3/4"-thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement.
30" Warmer Drawer Specifications
•
Product Weights – (E30WD75GPS / E30WD75GSS) 49 Lbs. /
(E30WD75GTT) 41 Lbs.
•
Voltage Rating – 120V / 450W / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 0.45 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120V = 3.75 Amps
•
Full base of solid plywood or similar material required, capable of supporting 100 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
SO_EW_WD INST 10/10 © 2010 Electrolux Home Products, Inc.
High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.
Printed in the U.S.A.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project