Konica Minolta Kit ~ Bizhub ~ 132312 2.2.30 - Print Version

Konica Minolta Kit ~
Bizhub ~ 132312
Installation Manual | Konica Minolta Kit ~ Bizhub ~
132312
Product Version: Colour V5
Version of this manual: 2.2.30
Inepro Kit number: 132312
Konica Kit number: 9967000949
© 2014 Inepro B.V. All rights reserved
Table of Contents
Introduction
Check Kit Content
Hardware Setup
2
4
10
1 Attach
........................................................................................................................................................
the PayCon to the bracket
10
2 Attach
........................................................................................................................................................
the bracket to the copier
11
Set up the copier
24
1 Konica
........................................................................................................................................................
Minolta Bizhub Colour V5
24
Set up the PayCon
28
1 Behaviour
........................................................................................................................................................ 28
2 Network
........................................................................................................................................................ 29
3 General
........................................................................................................................................................
Settings
30
Version 2.2.30 Inepro B.V.
http://www.inepro.com
Introduction
I
Part
Introduction
Introduction
This kit is meant for the following Konica Minolta Bizhub copiers:
Konica Minolta
-
Bizhub C203
Bizhub C220
Bizhub C280
Bizhub C360
Bizhub C451
Bizhub C550
Bizhub C650
Bizhub C452
Bizhub C552
Bizhub C652
To install this kit we shall:
1. Check the content of kit, read more on page
4
2. Prepare and construct the hardware. To read more go to page
3. Set up the copier, read more on page
4
4. Set up the PayCon, you will find more information on page
2
-
Konica Minolta Kit ~ Bizhub ~ 132312
4
4
Check Kit Content
II
Part
Check Kit Content
Check Kit Content
Before you start installing the kit, you should check if you have received all the packages you need.
KM Mounting kit for Bizhub colour V5
Please check the content of the box and make sure all kits are complete.
KM Mounting kit for Bizhub Colour V5
In the "KM Mounting kit for Bizhub Colour V5" you should find:
· 1x
PayCon copier mounting bracket
· 1x
KM cableset Minolta Serial I/F - V3
· 1x
KM screwset Bizhub V3 C550
· 1x
KM Mounting plate Bizhub Colour - V5
· 1x
This manual
· 1x
150cm Black cat 5 network cable
4
-
Konica Minolta Kit ~ Bizhub ~ 132312
KM Screwset Bizhub Colour V3
KM Screwset Bizhub Colour V3
In the "KM Screwset Bizhub Colour V3" you should find:
· 3x
M4 x 5mm Dome shaped, cross head screws
· 1x
M4 x 12mm Dome shaped, cross head screw
· 1x
M4 x 16mm Dome shaped, cross head screw
· 2x
M3 x 12mm Dome shaped, cross head screws
· 1x
M3 x 16mm Dome shaped, cross head screw
· 1x
M3 x 16mm Dome shaped, countersunk cross head screw
· 2x
M3 x 20mm Dome shaped, cross head screws
· 1x
M3 Star lock washer
· 4x
M4 Star lock washers
· 2x
M3 x 5mm spacer
· 1x
M3 x 15mm spacer
· 1x
M4 x 5mm spacer
· 1x
M4 x 12mm spacer
· 4x
M3 Black nylon cable guiders
· 1x
M4 Black nylon cable guider
· 5x
Rip Ties
· 1x
84cm x 15mm Black slit wrap harness (the black hose)
Version 2.2.30
-
5
Check Kit Content
KM Mounting plate Bizhub Colour V5
KM Mounting plate Bizhub Colour V5
1x KM mounting plate Bizhub Colour V5
6
-
Konica Minolta Kit ~ Bizhub ~ 132312
KM Cableset Minolta serial I/F V3
KM Cableset Minolta serial I/F V3
In the "KM Cableset Minolta serial I/F V3" you should find:
· 3x
Rip ties
· 1x
Ferrite core
· 1x
Connection cable
· 1x
Double sided adhesive tape 25mm x 30mm
· 1x
Connector block male/male
Version 2.2.30
-
7
Check Kit Content
PayCon copier mounting bracket
PayCon copier mounting bracket
In the "PayCon copier mounting bracket" you should find:
· 1x
PayCon copier mounting bracket
· 4x
Dome shaped, cross head screws
· 3x
Dome shaped, cross head screws (not needed for this installation)
Additional requirements for installation
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)
8
-
Konica Minolta Kit ~ Bizhub ~ 132312
Hardware Setup
III
Part
Hardware Setup
Hardware Setup
Additional requirements:
· Pair of wire cutters
· No. 2 cross head screwdriver
· No. 1 PosiDriv head screwdriver
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)
Attach the PayCon to the PayCon bracket
1. Break out the appropriate gaps in the flaps
2. Close the two left flaps and fasten the middle one with it's screw. Feed the wires through the bracket and connect the power supply to
the socket bottom-left to the 'Opto COM 12' and the copier cable to 'Opto COM 12' as shown in the picture
10
-
Konica Minolta Kit ~ Bizhub ~ 132312
Attach the PayCon to the bracket
3. Use the rip tie to attach the power cable and connection cable to the flap, thus creating a cable relief, and clip the rip tie using the wire
cutter
4. Close and gently screw down the last flap and place the PayCon bracket on the PayCon with the screws from the bracket kit
5. Place the ferrite cores and loop the network cables through them once
Attach the PayCon bracket to the copier
The mounting instructions differ for the different type of copiers its supports. The instructions for each part will start with
the list of copiers that the instructions are meant for.
- Bizhub C203
- Bizhub C253
- Bizhub C353
Version 2.2.30
-
11
Hardware Setup
1. Screw off the copier flap and open the scanner top to lift the flap out, and remove the backside flap as well.
2. Attach the cable with the 2 rip ties to the existing cable , as shown above. Make sure you do not allow the cable to be too long because
then it will hinder the door. Feed the cable to the backside of the copier through the inside.
3. Screw on the mounting plate. Screw on the two cable guiders with the spacers and screws. Screw down the rest of the cover with the
original cover screws.
12
-
Konica Minolta Kit ~ Bizhub ~ 132312
Attach the bracket to the copier
4. Screw on the PayCon with the 3 screws.
5. Loop the wire trough the ferrite core you will attach the the top, and use the existing cable guiders to guide the wire trough
6. Connect the copy cable and close the back and side flap. Guide the cables in the slit wrap harnas and attach it to the cable guide with
the rip ties. Connect the network cable to the socket hidden behind the corner flap
7. Remove the transport foils to finish the installation
Version 2.2.30
-
13
Hardware Setup
8. Finished
14
-
Konica Minolta Kit ~ Bizhub ~ 132312
Attach the bracket to the copier
-
Bizhub C451
Bizhub C550
Bizhub C650
Bizhub C452
Bizhub C552
Bizhub C652
1. Remove air cover, filter and back cover (2 pieces) connected with 12 screws
2. Remove 2 screws (because we need to place the mounting bracket) and cut out the hole for the cable. Place the mounting bracket and
the cable guiders.
3. Attach the PayCon. Shorten the cable to approximately 55 centimeters (21 segments should be cut off). Feed the cable through the slit
wrap harness. Feed the cable inside the copier. Attach the slit wrap harness to the cable guides with the rip ties.
Version 2.2.30
-
15
Hardware Setup
Photo for Bizhub C451, C550, C650
Photo for Bizhub C452, C552, C652
4. Place the ferrite core with the adhesive tape. Loop the cable in the ferrite core and run it through the original cable guiders. Connect the
cable to the connector inside the copier.
5. Replace the covers, filter and air cover.
6. Remove the transport foils to finish the installation
16
-
Konica Minolta Kit ~ Bizhub ~ 132312
Attach the bracket to the copier
7. Finished
Version 2.2.30
-
17
Hardware Setup
You will not need these items!
1. from the screwset
- 4x M3 black cable guider
- 2x M3 12mm screws
- 1x M3 16mm screw
- 1x M3 20mm screw
- 2x M3 x 5mm spacers
- 1x M3 x 12mm spacer
- 4x Black rip ties
2. from the cableset
- 2x White rip ties
18
-
Konica Minolta Kit ~ Bizhub ~ 132312
Attach the bracket to the copier
- Bizhub C220
- Bizhub C280
- Bizhub C360
1. Unscrew the white rim (3 screws) and the plastic cover (6 screws).
2. Remove protection cap
3. Open left protection cap and remove the 2 upper left screws
Version 2.2.30
-
19
Hardware Setup
4. Mount copy plate and the cable guide, you will need:
5. Mount the PayCon on the bracket.
6. Break open the break-out hole in the cover. Put the copy cable through the hole, connect the network cable behind the door and put the
rest of the cables in the cable hose.
20
-
Konica Minolta Kit ~ Bizhub ~ 132312
Attach the bracket to the copier
7. The cable should enter here.
8. Place the ferrite core on the plastic and loop the cable trough. Connect the cable to male connector.
9. Overview copy cable.
Version 2.2.30
-
21
Hardware Setup
10. Place the panels back on the copier. Unscrew the screw from the lower left panel, place the cable guide and ty rip the hose with the
cable to the guide.
11. Total overview.
1x
2x
1x
1x
3x
22
-
You will not need these items!
M3 x 20mm Dome shaped, cross head screws
M3 x 12mm Dome shaped, cross head screws
M3 x 15mm spacer
M4 x 12mm spacer
M3 Black nylon cable guiders
Konica Minolta Kit ~ Bizhub ~ 132312
Set up the copier
IV
Part
Set up the copier
Set up the copier
Turn on the copier. In this chapter you will set up the copier for use with the PayCon system. Examine the exact settings
below.
Konica Minolta Bizhub Colour V5
·
·
·
·
·
·
·
·
·
·
·
·
Konica Minolta Bizhub C203
Konica Minolta Bizhub C220
Konica Minolta Bizhub C253
Konica Minolta Bizhub C280
Konica Minolta Bizhub C353
Konica Minolta Bizhub C360
Konica Minolta Bizhub C451
Konica Minolta Bizhub C550
Konica Minolta Bizhub C452
Konica Minolta Bizhub C552
Konica Minolta Bizhub C652
Konica Minolta Bizhub C650
The PayCon Interface setting should be 'KoMi Serial'. (See chapter: 'Set up the PayCon' on page
24
-
Konica Minolta Kit ~ Bizhub ~ 132312
28
).
Konica Minolta Bizhub Colour V5
Activating the payment system:
Press <Utility/Counter>
Press <Meter Count>
Press <Check Details>
Press <stop> <0> <0> <stop> <0> <1> SERVICE MODE
Press <stop> <9>
Select <Management Function Choice>
Select <Vendor 2>
Select <Message>
Select <Type1> (for coins only) or
Select <Type2> (for cards only) or
Select <Type3> (for coin & card)
Leave the menu
Version 2.2.30
-
25
Set up the copier
Setting / unsetting restrictions of the MFP (default is all functionality maximum restricted!):
Press <Utility/Counter>
Select <Administrator Setting3> (or press <3>)
Press <1> <2> <3> <4> <5> <6> <7> <8> <OK>
Select <Security Settings> (or press <9>)
Select <Function Management Settings> (or press <7>)
Select <Usage Settings for Each Function> (or press <1>)
Set <ON>, <OFF> or <Restrict> for each individual function (Copy, Print and Send Scan/Fax)
- ON:
functionality only allowed when enough credit available from PayCon / PayMatic
- OFF: functionality available without any restrictions
- Restrict: functionality complete switched off for every usage
Leave the menu
Note: When "Print Function Setting" is set to "ON", all printjobs need a job log code. Printjobs without this code will be
automatically deleted at the MFP.
Note: when using central server software for controlling printjobs (like DocuPro or Pcounter) "Print Function Setting"
should be set to "OFF" (otherwise you have to pay twice).
26
-
Konica Minolta Kit ~ Bizhub ~ 132312
Set up the PayCon
V
Part
Set up the PayCon
Set up the PayCon
Turn on the PayCon. Refer to the technical PayCon Copy manual for handling the PayCon menu and changing settings.
The settings in the PayCon can be find in the tree-top menu structure of the PayCon. To simplify thing, we will use a
graphic representation of this menu to show you where the setting can be found.
The steps are represented by icons:
Insert your service card and enter the menu
Optional ECOS module
Press 1
Press Dot
Press 2
Press 0
Press 3
Press #
Press 4
Press +
Press 5
Press -
Press 6
Press F
Press 7
Press Stop
Press 8
Press ?
Press 9
Press the Flag
Press OK
Press Correction
Use the
The
,
and
,
and
to navigate, the
buttons can also be used as the
to edit the value, the
and
to confirm and the
to cancel.
buttons to navigate.
Look for all the actions of the buttons in the PayCon technical manual.
Behaviour
1. Where is the credit value kept?
a. On the card (SVC), you will need to use cards of the chipcard or Mifare card type and the
Payment Option', continue with step 2.
b. On the server (SVS), go to step 3.
c. On the PayCon terminal, you will need ECOS 'KM - I - Local Accounts', go to step 4.
2. Stored Value on Card:
a. If you use Mifare continue with 2b, if you use chipcards go to step 2d
b. , Go to 'Main Menu' => 'Card / ID' => 'ID Tags' => 'Mifare' => 'Mode'.
and go to step 2f.
c. Select 'Disabled', press
d. , Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => 'Inepro SLE'.
e. Select 'Disabled' and press .
f. Do you use Pcounter? if you do, continue with step 3, if you don't, go to step 8.
3. Do you use Cost Centres (Client Codes) in the PayCon System*?
* Sub Client Codes are not supported.
28
-
Konica Minolta Kit ~ Bizhub ~ 132312
ECOS 'KM - PayCon
Behaviour
a. , Go to 'Main Menu' => 'Card / ID' => 'General Settings' => 'Cost Centre Selection'.
b. If everybody is required to use a Cost Centre (Client Code), choose 'Required' and confirm with
not be able to use budget purses if there is no server connection.
c. If you don't use Cost Centres, choose 'Never' and confirm with .
d. If you only want to use it if the server is online, choose 'If online' and confirm with .
e. Go to step 5.
. The users will
4. Store Value on Terminal:
a. Set the account mode. , Go to 'Main Menu' => 'Card/ID' => 'Terminal Accounts' => 'Account Mode'.
and go to step 4e.
b. If you want all tags to be accepted select 'Allow all ID's' and confirm with
c. If you want to accept only tags that are registered in your PayCon select 'Allow accounts' and confirm with .
d. Setting up the accounts:
, Go to 'Main Menu' => 'Card/ID' => 'Terminal Accounts' => 'Add'.
·
to add an account.
· Type a card or account number and confirm with
· Repeat this until all accounts are set.
e. Setting the tags:
, Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => <Tag Type>.
·
· Select 'Disabled' and press .
, Go to 'Main Menu' => 'Card / ID' => 'Terminal Accounts' => 'Tags' => <Tag Type>.
·
· There are two ways to present a tag to the PayCon, you can swipe it past the reader or hold it in place on the
reader.
· Select 'Hold' or 'Swipe' and confirm with .
f. Go to Step 8
Network
5. Network Settings:
a. , Go to 'Main Menu' => 'Terminal' => 'Network'
b. Set the 'host name' to an identifiable name.
c. Confirm with .
d. If DHCP is used and go to step 7.
e. If DHCP isn't used, set it to 'disabled' and confirm with
.
6. Fixed IP addresses:
a. Set 'IP-address' to an IP-address in your network range and confirm with .
b. Set the subnet mask ('netmask') to '255.255.255.0' or to the subnet mask needed in your network and confirm with
.
c. Set the 'default gateway' to the IP-address of the default gateway in your network and confirm with .
7. DB Settings:
a. , Go to 'Main Menu' => 'DB Connectivity' => 'Server'
b. Set the IP-address of the PCounter server in 'Sever Address' and confirm with
c. , Go to 'Main Menu' => 'DB Connectivity' => 'Transaction log'
d. Select 'Enabled' and confirm with .
e. , Go to 'Main Menu' => 'DB Connectivity' => 'Printjob client'
f. Select 'Enabled' and confirm with .
.
Version 2.2.30
-
29
Set up the PayCon
General Settings
8. Copier Interface:
a. , Go to 'Main Menu' => 'Copier' => 'Interface'
b. Select the Interface setting for your machine and press
the copier', on page 24 .
. The correct settings can be found in the chapter: 'Set up
9. Products. The copy/print/scan products in the PayCon have a fixed order and number. They are used to connect the
paper signals form the copier to prices in the PayCon. These products and their names can also be set with PCounter.
a. , Go to 'Main Menu' => 'Products' => 'Product List'
b. Check if the default product list is complete, if so go to step 11, if not continue with step 10.
PayCon
product
number
0
1
2
3
4
5
6
7
1000
1001
1002
1003
1004
1005
1006
1007
2000
2001
2002
2003
3000
3001
3008
PayCon product
display name
A4 b/w
A3 b/w
A4 colour
A3 colour
A4 b/w dpx
A3 b/w dpx
A4C dpx
A3C dpx
Print A4 b/w
Print A3 b/w
Print A4C
Print A3C
Print A4 b/w dpx
Print A3 b/w dpx
Print A4 colour dpx
Print A3 colour dpx
Scan A4 b/w
Scan A3 b/w
Scan A4C
Scan A3C
Fax A4
Fax A3
Fax Start
PayCon
default
price
€ 0,05
€ 0,10
€ 0,50
€ 1,00
€ 0,05
€ 0,10
€ 0,50
€ 1,00
€ 0,05
€ 1,00
€ 0,50
€ 1,00
€ 0,05
€ 0,10
€ 0,50
€ 1,00
€ 0,01
€ 0,02
€ 0,03
€ 0,06
€ 0,05
€ 0,10
€ 0,25
Supported by
Corresponds with photocopier product
A4 black and white
A4 black and white
A4 colour (single until full)
A3 colour (single until full)
Backside of duplex A4 black copy
Backside of duplex A3 black copy
Backside of duplex A4 colour copy
Backside of duplex A3 colour copy
A4 black and white print
A3 black and white print
A4 colour print
A3 colour print
A4 black and white duplex print
A3 black and white duplex print
A4 colour duplex print
A3 colour duplex print
A4 black and white scan
A3 black and white scan
A4 colour scan
A3 colour scan
A4 black and white fax
A3 black and white fax
Start tariff for fax
All copiers
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Note that not every product is supported by each interface!
X
= Supported
= Not supported
10. Edit Product:
a. To add a product, go to 'Add product', enter a number and press .
b. To edit it's properties, go to 'Main Menu' => 'Products' => 'Product List', select it and press .
c. Check the price and if the index number corresponds with the copy product index number in the table.
11. Purse Selection, manage the way the purse is selected.
a. , Go to 'Main Menu' => 'Card/ID' => 'Generic Settings' => 'Purse Selection'.
b. Select the selection behaviour in the list (look for a description in the table) confirm with
30
-
Konica Minolta Kit ~ Bizhub ~ 132312
.
General Settings
Purse Selection
All Purses
Personal Only
Budget Only
Prefer Personal
Prefer Budget
Personal + Ask
Budget + Ask
Description
Accept all purses
Only accept personal credit
Only accept non-personal budget
If the card has a personal credit, pay out of that credit
If the card has a non-personal budget, pay out of that budget
Ask which budget and select personal credit as default
Ask which budget and select non-personal budget as default
12. Maximum Balance, the Maximum Balance allowed on a card or account.
a. , Go to 'Main Menu' => 'Card/ID' => 'Generic Settings' => 'Maximum Balance'.
b. Type in the maximum balance and confirm with .
13.Project ID, the unique number for all PayCon's on this project or site.
a. , Go to 'Main Menu' => 'Terminal' => 'Project ID'
b. Press , type the Project ID and confirm with .
14. Date and Time, the time and date that are used for the timestamp on the transactions. Remember if the timezone is
changed the time will change accordingly.
a. So first set the timezone by , go to 'Main Menu' => 'Terminal' => 'Date/Time' => 'Timezone'.
b. Select the timezone and confirm with .
c. Check the time (go to 'Main Menu' => 'Terminal' => 'Date/Time' => 'Time') and change it if needed.
d. In the same manner check the date.
15. Currency, the currency used in the PayCon
a. , Go to 'Main Menu' => 'Terminal' => 'Currency' => 'Accepted Currency'.
b. Select the currency and confirm with .
c. Go to 'Main Menu' => 'Terminal' => 'Currency' => 'Old Currency'.
d. Select the currency and confirm with .
16. Default language, the language the PayCon uses to communicate with the user. A second and third language can
also be set. When the user presses , the next available language will be used.
a. , Go to 'Main Menu' => 'Terminal' => 'Default Language'.
b. Select a language from the list and confirm with .
c. Go to 'Main Menu' => 'Terminal' => '<Nth> Language' to add extra languages in the same way.
Version 2.2.30
-
31