Samsung AD24B1(B2)(C1)(C2)E12 Installation guide

Indoor Unit
Outdoor Unit
AD18B1(B2)(C1)(C2)E09
AD19B1(B2)(C1)(C2)E07
AD19B1(B2)(C1)(C2)E12
AD24B1(B2)(C1)(C2)E12
AD26B1(B2)(C1)(C2)E07
AD26B1(B2)(C1)(C2)E12
MH18ZA1(A2)(C1)(C2)-09
MH19ZA1(A2)(C1)(C2)-07
MH19ZA1(A2)(C1)(C2)-12
MH24ZA1(A2)(C1)(C2)-12
MH26ZA1(A2)(C1)(C2)-07
MH26ZA1(A2)(C1)(C2)-12
UD18B1(B2)(C1)(C2)E2
UD19B1(B2)(C1)(C2)E2
UD24B1(B2)(C1)(C2)E2
ENGLISH
ESPAÑOL
ITALIANO
OWNER’S INSTRUCTIONS
MANUAL DE INSTRUCCIONES
ISTRUZIONI PER L’USO
MANUAL DE INSTRUÇÕES
MANUEL D’UTILISATION
GEBRAUCHSANWEISUNG
O¢H°IE™
MH18ZA1(A2)(C1)(C2)X
MH19ZA1(A2)(C1)(C2)X
MH24ZA1(A2)(C1)(C2)X
PORTUGUÊS
UD26B1(B2)(C1)(C2)E3
DEUTSCH
E§§HNIKA
MULTI-SPLIT TYPE ROOM AIR CONDITIONER ( Cool and Heat )
ACONDICIONADOR DE AIRE DOMÉSTICO SISTEMA MULTI SPLIT ( Refrigeración y Calefacción )
CONDIZIONATORE D’ARIA PER PIÙ AMBIENTI AD UNITÀ SEPARATE ( Raffreddamento e Riscaldamento )
AR CONDICIONADO MULTI SPLIT ( Refrigeração e Aquecimento )
CLIMATISEUR DE TYPE MULTIPLE ( Refroidissement et Chauffage )
RAUMKLIMAGERÄT IN MEHRFACH GETEILTER AUSFÜHRUNG ( Kühlen und Wärmen )
¶O§Y¢IAIPOYMENO K§IMATI™TIKO ¢øMATIOY(æ‡Í˘ Î·È £¤ÚÌ·ÓÛ˘)
FRANÇAIS
MH26ZA1(A2)(C1)(C2)X
E S I P F D G DB68-01282A(5)
Safety Precautions
The following safety precautions must be taken when using your air conditioner.
1
Make sure that the indoor unit is correctly ventilated at all times; do NOT place clothing or other materials
over it.
2
NEVER spill liquid of any kind into the indoor unit. Should this happen, switch off the breaker used for your
air conditioner and contact your installation specialist.
3
Do NOT insert anything between the air flow blades, as the inner fan may become damaged and you may be
hurt. Keep children away from the indoor unit.
4
Do NOT place any obstacles in front of the outdoor unit.
5
If the remote control will not be used for a long time, remove the batteries.
6
Users of this product are cautioned not to attempt repair of this product at their own discretion.
Instead, they are requested to directly contact a designated service center or the outlet at which the
product was purchased.
7
If the supply cord is damaged, it must be replaced by a special cord or assembly available from the
manufacturer or its service centre.
8
This device must be installed according to the national electrical rules.
9
Before disposing of the remote control it is necessary to remove batteries.
10 The appliance is not intended for use by young children or infirm person without supervision;
young children should be supervised to ensure that they do not play with the appliance.
CAUTION
The manufacturer does not take any responsibility for any accidents that
occur because the air conditioner is not fixed firmly or installed securely,
during installing or using the product. In case you experience difficulty in
installation, you must use an installation specialist. An accident will occur
if the installation is not done as recommends in the installation guide.
E-2
ENGLISH
Contents
◆ PREPARING YOUR AIR CONDITIONER
■ Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
■ View of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
■ Remote Control-Buttons and Display . . . . . . . . . . . . . . . . . . . . .6
■ Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
■ Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . .8
◆ OPERATING YOUR AIR CONDITIONER
■ 5 Way Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
■ Selecting the Automatic Operating Mode . . . . . . . . . . . . . . . . .10
■ Cooling Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
■ Heating Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
■ Changing the Room Temperature Quickly . . . . . . . . . . . . . . . .13
■ Removing Excess Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . .14
■ Airing Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
■ Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . .16
■ Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . .17
◆ PROGRAMMING YOUR AIR CONDITIONER
■ Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
■ Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
■ Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
◆ RECOMMENDATIONS FOR USE
■ Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . .21
■ Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . .22
■ Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . .22
■ Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . .23
■ Installing a Filter (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
■ Operation Function Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
◆ TECHNICAL SPECIFICATIONS
E-3
View of the Unit
The design and shape are subject to change according to the model.
Indoor Unit
Air filter
(under the grille)
Air flow blades (outlet)
Air Inlet
Timer indicator
Remote Control Sensor
STANDARD indicator
SAVING indicator
SILENCE indicator
NATURE indicator
POWER indicator
On/Off & 5 Way
selection button
Note
E-4
◆ For details on the 5 Way, refer to page 9.
ENGLISH
Indoor Unit
✴✴✴✴C1(C2)✴✴✴✴
Air filter
(under the grille)
Air Inlet
Air flow blades (outlet)
On/Off & 5 Way
selection button/
Remote Control Sensor
TIMER indicator
STANDARD indicator
SILENCE indicator
NATURE indicator
SAVING indicator
POWER indicator
Note
◆ For details on the 5 Way, refer to page 9.
Outdoor Unit The design and shape are subject to change according to the model.
Air Inlet(Rear)
Air Inlet(Rear)
Air Outlet
Air Outlet
Connection
Valve
Connection
Valve
E-5
Remote Control - Buttons and Display
Remote control
transmission indicator
Operating mode
(
AUTO,
COOL,
DRY,
FAN,
HEAT)
Temperature setting
Turbo mode
Sleep mode
Fan speed
Mode selection button
(AUTO, COOL, DRY, FAN, HEAT)
Temperature adjustment
buttons
Turbo/Sleep mode
selection button
Air flow direction
Fan speed adjustment
button
Swing button
On Timer setting
On Timer button
Off Timer setting
Off Timer button
Battery discharge indicator
5 Way selection button
E-6
On/Off &
Timer Set/Cancel button
ENGLISH
Getting Started
You have just purchased a split type air conditioner and it has been
installed by your installation specialist.
Your Owner’s Instructions contains valuable information on using your
air conditioner. Please take the time to read it as it will help you take full
advantage of the unit’s features.
The booklet is organized as follows.
◆ The following figures are shown on pages from 4 to 6 :
- Indoor and outdoor units
- Remote control(buttons and display)
They will help you find the buttons and understand the symbols displayed.
◆ In the main part of the installation book, you will find a series of
step-by-step procedures for each function available.
The illustrations in the step-by-step procedures use three different symbols:
PRESS
PUSH
HOLD DOWN
E-7
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when :
◆ You purchase the air conditioner
◆ The remote control does not work correctly
Note
E-8
◆
◆
◆
◆
Use two AAA, LR03 1.5V batteries.
Do not use old batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months, even
if they have not actually been used.
1
Push the battery cover on the rear of the remote control with your thumb
in the direction of the arrow and remove it.
2
Insert the two batteries, taking care to respect the polarities :
◆ + on the battery with + on the remote control.
◆ - on the battery with - on the remote control.
3
Close the cover by sliding it back until it clicks into place.
ENGLISH
5 Way Function
You can select the 5 Way function with operating mode of the air conditioner for
more comfortable circumstances. You can use the 5 Way function with the indoor
unit as well as the remote control. Thus, you can use this function
even though you have lost your remote control.
Using with the indoor unit
1
Press the
mode.
(ON/OFF) button one time and then select the desired
To obtain a(n)...
Then select...
Normal operating
(STANDARD) mode
Reducing the uncomfortable
temperature gradually
(NATURE) mode
High fan speed
(POWER) mode
Compressor run time reduced
(SAVING) mode
Fan speed reduces as the temperature
decreases
(SILENCE) mode
✴✴✴✴C1(C2)✴✴✴✴
To obtain a(n)...
Then select...
Normal operating
(STANDARD) mode
Reducing the uncomfortable
temperature gradually
(NATURE) mode
High fan speed
(POWER) mode
Compressor run time reduced
(SAVING) mode
Fan speed reduces as the temperature
decreases
2
To stop the operating, press the
turn off.
Note
(SILENCE) mode
(ON/OFF) button until all indicators
Even if the air conditioner has been turned on via the ON/OFF
button on the unit, operations can still be controlled using the
remote control as usual.
Selecting with the Remote Control
To select the 5 Way function with the remote control, press the 5 Way
button one or more times until the desired mode is selected.
◆ Each time you press the 5 Way button:
✴✴✴✴C1(C2)✴✴✴✴
Each 5 Way indicator on the indoor unit lights up in order.
E-9
Selecting the Automatic Operating Mode
You can start the air conditioner in Automatic mode from your remote
control. In the Automatic mode, the standard temperature and the
optimum fan speed is selected automatically. You can adjust the
standard temperature but not the fan speed.
1
If necessary, press the
Result:
IMPORTANT
(On/Off) button.
◆ The 5 Way indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
lt will start up normally after three minutes.
2 If the
is not displayed at the top of the remote control,
press the MODE button on the remote control one or more times until it
appears.
3
Result:
◆ The indoor unit beeps each time you press the MODE button.
◆ The air conditioner runs in AUTO mode.
Note
You can change modes at any time.
To adjust the standard temperature (The air conditioner automatically
set the standard temperature by the current room temperature.),
press the TEMPERATURE buttons one or more times.
SET TEMP. SET TEMP.
-2°C
-1°C
< When you feel hot >
E-10
Standard temperature
SET TEMP. SET TEMP.
+1°C
+2°C
< When you feel chilly >
ENGLISH
Cooling Your Room
You must select the Cool mode if you wish to adjust the:
◆ Cooling temperature
◆ Fan speed when cooling
1
If necessary, press the
Result:
IMPORTANT
(On/Off) button.
◆ The 5 Way indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
lt will start up normally after three minutes.
2 If the
is not displayed at the top of the remote control,
press the MODE button on the remote control one or more times until it
appears.
3
Result:
◆ The indoor unit beeps each time you press the MODE button.
◆ The air conditioner runs in COOL mode.
Note
You can change modes at any time.
To adjust the temperature, press the TEMPERATURE buttons one or
more times until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result:
4
◆ Each time you press the TEMPERATURE buttons:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts cooling, provided that the room
temperature is higher than the selected temperature;
the fan will, however, operate.
Select the fan speed by pressing the FAN button one or more times
until the required setting is displayed:
Automatic (rotated :
)
Low
Medium
High
Result:
5
Each time you press the FAN button, the indoor unit beeps.
To control the direction of the air flow, refer to page 16 and 17.
E-11
Heating Your Room
You must select the Heat mode if you wish to adjust the:
◆ Heating temperature
◆ Fan speed when heating
1
If necessary, press the
Result:
IMPORTANT
2
(On/Off) button.
◆ The 5 Way indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected when
the unit was last used.
◆ The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
It will start up normally after three minutes.
If the
is not displayed at the top of the remote control, press the
MODE button on the remote control one or more times until it appears.
◆ The indoor unit beeps each time you press the MODE button.
◆ The air conditioner runs in HEAT mode.
N o t e You can change modes at any time.
Result:
3
To adjust the temperature, press the TEMPERATURE buttons one or
more times until the required temperature is displayed.
Possible temperatures are between 16°C and 30°C inclusive.
Result:
4
◆ Each time you press the TEMPERATURE buttons:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts heating, provided that the room
temperature is lower than the desired temperature
(selected temperature+3°C); the fan will, however, operate.
Select the fan speed by pressing the FAN button one or more times
until the required setting is displayed:
Automatic (rotated :
)
Low
Medium
High
Result:
5
E-12
◆ Each time you press the FAN button, the indoor unit beeps.
◆ For the first three to five minutes, the fan operates very
slowly until the air has been sufficiently warmed. Once the
correct temperature has been reached, the fan is automatically
set to the required speed.
To control the direction of the air flow, refer to page 16 and 17.
ENGLISH
Changing the Room Temperature Quickly
The Turbo cooling/heating function is used to cool or heat your room as
quickly as possible.
Example :
You have just come home and find that the room is very
hot. You wish to cool it down as quickly as possible.
The Turbo function operates for 30 minutes with the maximum settings before
returning automatically to the mode and temperature previously selected.
1
If necessary, press the
Result:
2
Press the
Result:
3
button.
◆ The temperature and fan settings are adjusted automatically.
◆ The air conditioner cools or heats the room as quickly as possible.
◆ After 30 minutes, the air conditioner is reset automatically to the
previous mode, temperature and fan settings.
But, if you press the
button in DRY or FAN mode,
it will change to AUTO mode automatically.
If you wish to stop the Turbo function before the end of the 30-minute period,
press the
button one or more times until
or
disappears.
Result:
4
(On/Off) button.
◆ The 5 Way indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected when the unit
was last used.
◆ The indoor unit beeps.
The air conditioner is reset automatically to the previous mode,
temperature and fan settings.
To control the direction of the air flow, refer to page 16 and 17.
E-13
Removing Excess Humidity
If the atmosphere in your room is very humid or damp, you can
remove excess humidity without lowering the room temperature too
much.
1
If necessary, press the
Result:
◆ The 5 Way indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected when
the unit was last used.
◆ The indoor unit beeps.
IMPORTANT
2
(On/Off) button.
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
It will start up normally after three minutes.
If the
is not displayed at the top of the remote control, press the
MODE button on the remote control one or more times until it appears.
◆ The indoor unit beeps each time you press the MODE button.
◆ The air conditioner runs in DRY mode.
N o t e You can change modes at any time.
Result:
3
To adjust the temperature, press the TEMPERATURE buttons one or
more times until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result:
4
E-14
◆ Each time you press the TEMPERATURE buttons:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts removing the excess humidity;
the quantity of air is adjusted automatically.
To control the direction of the air flow, refer to page 16 and 17.
ENGLISH
Airing Your Room
If the atmosphere in your room is stale, you can air the room using
the Fan feature.
1
If necessary, press the
Result:
2
◆ The 5 Way indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected when
the unit was last used.
◆ The indoor unit beeps.
If the
is not displayed at the top of the remote control,
press the MODE button on the remote control one or more times until it
appears.
Result:
Note
3
(On/Off) button.
◆ The indoor unit beeps each time you press the MODE button.
◆ The air conditioner runs in FAN mode.
◆ The temperature is set automatically.
You can change modes at any time.
Select the fan speed by pressing the FAN button one or more times
until the required setting is displayed:
Low
Medium
High
Result:
4
Each time you press the FAN button, the indoor unit beeps.
To control the direction of the air flow, refer to page 16 and 17.
E-15
Adjusting the Air Flow Direction Vertically
Depending on the position of the indoor unit on the wall of your
room, you can adjust the position of the outer air flow blade on the
bottom of the unit, thus increasing the efficiency of the air
conditioner.
1
Press the SWING button one or more times as required.
Result: The outer blade is adjusted vertically.
RECOMMENDATION
2
Upwards.
Downwards.
The blade move up and down, around the base position set.
To stop the blade moving up and down, press the SWING button again.
Note
E-16
Adjust the blade to face...
Cooling
Heating
If you want the blade to move up and down automatically when the air
conditioner is operating, press the SWING button.
Result:
3
When...
If you switch the air conditioner... Then the blade is...
Off
Closed completely.
On again
Reset to the position that you
previously selected.
ENGLISH
Adjusting the Air Flow Direction Horizontally
There are two sets of inner air flow blades. Just as the outer air flow
blade can be adjusted vertically, the inner blades can be adjusted
horizontally.
1
Adjust each set of inner blades to the required position, by pushing or
pulling them sideways.
❄ The design and shape are subject
to change according to the model.
E-17
Setting the On Timer
The On Timer enables you to switch on the air conditioner automatically
after a given period of time. You can set the period of time from
30 minutes to 24 hours.
1
To set the operating time, press the ON TIMER button one or more times
until the required time is displayed. Possible time is between 0.5 hour and
24 hour inclusive.
2
Press the
Result:
3
(Set/Cancel) button to complete the setting.
◆ The remaining time is displayed.
◆ Blinking of the timer indicator stops.
◆ The selected mode and the temperature on the display
disappear after 10 seconds.
◆ The air conditioner will switch on automatically when the
counter displayed on the remote control reaches the set time
and disappears the On timer setting.
To select an operating mode in advance, press the
button until the
desired mode is displayed at the top of the remote control.
Result:
◆ The air conditioner will run in the selected mode when it is
turned on.
To Cancel the On Timer
1
To cancel the On Timer, press the ON TIMER button one or more times
until the timer setting disappears.
2
Press the
Note
E-18
(Set/Cancel) button.
If you want to turn on the air conditioner before the timer reaches
the setting time, press the (ON/OFF) button.
ENGLISH
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner automatically
after a given period of time. You can set the period of time from
30 minutes to 24 hours.
1
To set the operating time, press the OFF TIMER button one or more times
until the required time is displayed. Possible time is between 0.5 hour and
24 hour inclusive.
2
Press the
Result:
(Set/Cancel) button to complete the setting.
◆ The remaining time is displayed.
◆ Blinking of the timer indicator stops.
◆ The air conditioner will switch off automatically when the
counter displayed on the remote control reaches the set time
and disappears the Off timer setting.
Example If you would like to turn the air conditioner on after 2 hours
and to operate it for 2 hours:
1. Press the ON TIMER button until ‘2.0 Hr’ is displayed.
2. Press the (Set/Cancel) button.
3. Press the OFF TIMER button until ‘4.0 Hr’ is displayed.
4. Press the (Set/Cancel) button.
Note
You can see or change the setting mode and/or the temperature
by pressing the MODE button or the TEMPERATURE buttons
after setting the Off timer.
To Cancel the Off Timer
1
To cancel the Off Timer, press the OFF TIMER button one or more times
until the timer setting disappears.
2
Press the
Note
(Set/Cancel) button.
If you want to turn off the air conditioner before the timer reaches
the setting time, press the
(ON/OFF) button.
E-19
Setting the Sleep Timer
The Sleep Timer can be used when you are cooling or heating your
room to switch the air conditioner off automatically after a period of
six hours.
Note
If you wish to switch the unit off at a specific time, refer to
page 19.
1
Make sure that you have selected either COOL or HEAT mode.
2
Press the
button one or more times until
remote control.
◆ The indoor unit beeps.
◆ The air conditioner will be controlled as indicated in the
illustrations below.
Result:
Cooling
Heating
appears on the
The desired temperature is
increased by 1°C every hour.
When it has been increased
by 2°C (after two hours), the
temperature is maintained for
four hours.
The desired temperature is
decreased by 1°C every hour.
When it has been decreased
by 2°C (after two hours), the
temperature is maintained for
four hours.
2°C
1°C
Set
TEMP.
1hr 2hr
Start
time
Stop
time
1hr 2hr
Set
TEMP.
6hr
Stop
time
Start
time
6hr
-1°C
-2°C
To Cancel the Sleep Timer
If you no longer wish to use the Sleep Timer that you have set, you
can cancel it at any time.
Press the
Result:
E-20
button.
◆
◆
◆
The indoor unit beeps.
The
is no longer displayed.
The air conditioner operates normally.
ENGLISH
Operating Recommendations
Here are a few recommendations that you should follow when using
your air conditioner.
Topic
Recommendation
Heating performances
The heat pump inside the air conditioner
absorbs heat from outside air and brings it
indoors. If the temperature of the outside air
drops, the air conditioner will heat less. If you
find that the room is not warm enough, use an
additional heating appliance.
Warm air circulation
The air conditioner circulates warm air to heat
your room; as a result, some time will be
required after starting the air conditioner to
warm the entire room. If necessary, set the air
conditioner on before you wish to use the
room.
Frost
When outside temperatures are low and
humidity is high, frost may form in the outdoor
unit when heating is selected.
If this happens:
◆ The heating operation is stopped.
◆ The Deice mode is triggered automatically
for about seven minutes.
No intervention is required from you; after
about seven minutes, the air conditioner starts
operating again normally.
High indoor and outdoor
temperatures
If both the indoor and outdoor temperatures
are high and you select the Heat mode, the
outdoor unit’s fan and compressor may stop at
times. This is normal; simply wait until the air
conditioner switches on again.
Power failure
If a power failure occurs when the air
conditioner is operating, the unit is switched off.
When the power returns,
Note
✴✴A1✴✴
✴✴B1✴✴
✴✴C1✴✴
you must press the
button to restart it.
✴✴A2✴✴
✴✴B2✴✴
✴✴C2✴✴
the air conditioner starts up
again automatically
(ON/OFF)
Be sure which model you have purchased because some
air conditioners do not restart automatically.
E-21
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges
within which the air conditioner can be used.
If the air conditioner is used at...
Then...
High temperatures
The automatic protection feature may
be triggered and the air conditioner
stopped.
Low temperatures
A water leak or some other malfunction
may occur if the heat exchanger
freezes.
High humidity levels
Water may condense on and drip
from the surface of the indoor unit if it
is used for long periods.
Mode
Outdoor Temperature
Heating
0°C to 24°C approx.
Cooling
Drying
❇
Indoor Temperature
Indoor Humidity
27°C or less
-
21°C to 43°C approx.
18°C to 32°C approx.
80% or less
18°C to 43°C approx.
18°C to 32°C approx.
-
If the heating operation is used at below 0°C(outdoor
temperature) then, it does not heat at its full capacity.
If the cooling operation is used at over 33°C(indoor temperature)
then, it does not cool at its full capacity.
Cleaning Your Air Conditioner
To get the best possible use out of your air conditioner, you must
clean it regularly to remove the dust that accumulates on the air filter.
IMPORTANT
yy
;;
y
;
;
y
;
y
;;
yy
;
y
yy
;;
y
;
y
;
yy;;
;;
;yy;
yy
1
Open the front grille by lifting the tabs on the lower right and left sides of
the indoor unit.
2
Disassemble the front grille by pulling it forwards.
3
Hold the edge of the air filter under the front grille and pull to release them.
4
Remove all dust on the air filters with a vacuum cleaner or brush.
5
Clean the front panel with a damp cloth and mild detergent (do NOT use
benzene, solvents or other chemicals).
6
Reassemble the air filters and the front grille.
Note
E-22
Before cleaning your air conditioner, ensure that you
have switched off the breaker used for the unit.
◆ If you have not used the air conditioner for a long period
of time, set the fan going for three to four hours to dry the
inside of the air conditioner thoroughly.
ENGLISH
Solving Common Problems
Before contacting the after-sales service, perform the following simple checks.
They may save you the time and expense of an unnecessary call.
Problem
Explanation/Solution
The air conditioner does not
operate at all
◆ Check that the breaker used for the air conditioner is switched on.
◆ Check that the 5 Way indicator on the indoor unit is on;
if necessary press the
(On/Off) button on the remote control.
◆ Check whether the TIMER indicator on the indoor unit is switched on.
If so:
- Wait until the switch-on time is reached and the air conditioner starts
up automatically
- Cancel the timer (see pages 18 and 19 for further details)
The air conditioner does not
operate with the remote control
◆ Check that there are no obstacles between you and the indoor unit.
◆ Check the remote control batteries.
◆ Check that you are close enough to the indoor unit (seven metres/
yards or less).
No beep is heard when you press
the
(On/Off) on the remote
control
◆ Check that you are pointing the remote control at the remote control
sensor in the right of the indoor unit.
◆ Replace the remote control batteries if necessary.
The air conditioner does not cool
or heat
◆ Check that the correct operating mode has been selected (AUTO,
COOL, HEAT).
◆ The room temperature may be too low or too high.
◆ Dust may be blocking the air filter guard; refer to page 22 for cleaning
instructions.
◆ Check that there is no obstacle in front of the outdoor unit.
When heating, the required room
temperature is never reached and
the air conditioner frequently stops
◆ Check that the required temperature has been set correctly.
◆ Increase the fan speed.
◆ If the air flow is directed downwards, use the remote control to direct it
upwards.
The fan speed does not change
when you press the FAN button
◆ Check that the operating mode is set to COOL, HEAT or FAN ; in the
AUTO mode, the fan speed changes automatically and in the
DRY mode, it is set to AUTO.
The air flow direction does not
change when you press the
SWING button
◆ Check that the air conditioner has been switched on; if necessary,
press the
(On/Off) button on the remote control.
The timer is not correctly triggered
◆ Check that the timer has been programmed correctly; see pages 18
and 19.
Odours are permeated in the room
during air conditioning
◆ Air the room.
E-23
Installing a Filter (Option)
The air conditioner can be fitted with a deodorizing and Bio-Pure
filter to remove minute dust particles or odours. The service life of
the filter is approximately three months depending on the time
during which the air conditioner is used.
1
Note
Deodorizing
filter
Bio-Pure Filter
Remove the vinyl packing from the filter.
Do not remove the packing from a deodorizing filter until you
wish to use the filter, as it will lose its properties.
2
Insert the filter in the filter holder and press the three insert tabs until
you hear a click.
3
Open the front grille by pulling on the tabs on the lower right and left
sides of the indoor unit.
4
Take out the existing filter and replace it with the new one.
Operating Function Chart
◆ A unit and B(C) unit are operated in a different operation mode.
◆ If the mixing operation of A unit (cooling) and B(C) unit (heating) is
selected, the outdoor fan operates in the low speed.
◆ The operation mode of each unit is shown in the following table.
A-unit
AUTO (COOL)
AUTO (COOL)
AUTO (HEAT)
AUTO (HEAT)
COOL
COOL
HEAT
HEAT
FAN
FAN
DRY
E-24
B(C)-unit
DRY
ENGLISH
Technical Specifications
Model Indoor unit
Power Supply
AD18B1(B2)(C1)(C2)E09
AD19B1(B2)(C1)(C2)E07
AD19B1(B2)(C1)(C2)E12
AD24B1(B2)(C1)(C2)E12
AD26B1(B2)(C1)(C2)E07
AD26B1(B2)(C1)(C2)E12
220-240V~, 50Hz
MH18ZA1(A2)(C1)(C2)-09
MH19ZA1(A2)(C1)(C2)-07
MH19ZA1(A2)(C1)(C2)-12
MH24ZA1(A2)(C1)(C2)-12
MH26ZA1(A2)(C1)(C2)-07
MH26ZA1(A2)(C1)(C2)-12
◆ Package Weight
Model
Paper
Plastic
Wood
AD18B1(B2)(C1)(C2)E09
AD19B1(B2)(C1)(C2)E07
AD19B1(B2)(C1)(C2)E12
MH18ZA1(A2)(C1)(C2)-09
MH19ZA1(A2)(C1)(C2)-07
MH19ZA1(A2)(C1)(C2)-12
3.99kg
0.99kg
-
AD24B1(B2)(C1)(C2)E12
MH24ZA1(A2)(C1)(C2)-12
5.40kg
1.52kg
-
AD26B1(B2)(C1)(C2)E07
AD26B1(B2)(C1)(C2)E12
MH26ZA1(A2)(C1)(C2)-07
MH26ZA1(A2)(C1)(C2)-12
6.38kg
1.66kg
-
E-25
THIS AIR CONDITIONER IS MANUFACTURED BY:
ESTE AIRE ACONDICIONADO HA SIDO FABRICADO POR:
QUESTO CONDIZIONATORE D’ARIA È PRODOTTO DA:
ESTE APARELHO DE AR CONDICIONADO É FABRICADO POR:
CE CLIMATISEUR EST FABRIQUE PAR:
DIESE KLIMAANLAGE IST FABRIZIERT VON:
AYTH H ™Y™KEYH KATA™KEYA™THKE A¶O:
ELECTRONICS
Printed in Korea