Pyramid Time Systems 5000+ HD User manual

connections
NEW Products & Special Offers
A small selection from the 5000+ AV products
on www.keene.co.uk
Established in 1988
Trading online since 1996
HDMI 1:2 Distribution
Gigavideo 821 Wireless HDMI Sender
The Coosis 2 way HDMI Distribution
amplifier is a compact device that gives
two simultaneous HDMI outputs from
one HDMI input, ideal for viewing on
multiple displays. The Coosis units can
also be cascaded together in a
“pyramid” network to provide a oneto-many solution.
•Replace your HDMI cable wirelessly and locate your HDTV or
projector wherever you want
•Mount the receiver (out of sight) behind your HDTV or
on the ceiling next to your projector. No more visible cables
•Watch up to 2 (HD) devices such as Blu-ray® players,
DVRs, HD set-top boxes, game consoles etc, and
easily switch between the sources connected without
changing plugs
•The built-in HDMI splitter means that you can continue
to watch the connected devices locally
•Operate your A/V sources from anywhere, even through
a wall or cupboard door, using the IR receiver
•The HD signal does not experience any delays and is
therefore perfect for game consoles
•Digitally supports all 480p, 720p, 1080i and 1080p
(Full HD) resolutions from up to 30 metres
Please note: If the max resolutions of
your displays are different, the EDID
functionality will detect all the
connected displays' EDID nformation
and auto-match the output resolution
to the lower one. For example, if one
display supports 720P resolution and
the rests support 1080P, the signal will
be lowered to 720p for all displays.
Digital Audio Lip-Sync Corrector
The quality of an HDMI cable has a
great impact on signal transmission.
For best image quality, we suggest you
use a copper based HDMI cable.
Package contents:
1 X Coosis 2 way HDMI Distribution
amplifier
1 X Power Supply (+5V DC, 1A)
1 X User Manual
Our best selling
HDMI splitter!
Code HDC12
34.99
£
Audio AV Switching & Distribution Conversion & Distribution HDMI Cables CAT5 & Networking Cabling 2-7
8-9
10-11
12
13
HDMI Solutions 14-19
Power Solutions 20
AV Plates & Panels 21
IR Control Solutions 22-28
IR & AV Cables 29
Order Now
01332 830550
Monday to Friday 9.00am and 5.00pm
Code GV821 £265.00
See Page 5
Code DD740 £169.00
Bluetooth In-Wall Stereo Amplifier
•Add music to you kitchen, bedroom, bathroom, study
• Powerful true 20W RMS per channel output
•Fits into a standard UK two gang pattress
• Built In FM Radio with ten station memory
•Front jack input
• Rear line level input
• Bluetooth for easy music streaming from phone or tablet
• Front panel control plus Infra Red remote control
• Smooth tactile moisture resistant front panel switches
• LED's for status and confirmation
• Flush mount or surface mount (25mm depth)
See Page 17
New Low Price!
•
Absolutley the best most definitive answer to lip sync
problems on the market today!
•680ms delay (340ms for 96kHz signals)
•On-the-fly adjustment with no image overlay
•Tweaking in 1ms and 1/3ms steps
•36 preset delays for instant recall
•Discrete input switching, with input's last
delay restored
•Automatic optical-to-coax/coax-to-optical conversion
•4 digital audio inputs, 2 digital audio outputs
(optical and coax)
Max. recommended cable length after
amplifier: 10 metres
New Low Price!
New product!
See Page 2
Code KLAB20DB
£149.99
AV Supports 30
Camera Supports 31
Audio – Microphones 32
D-SLR 34
AV Accessories 36
For more new products and bargains visit
www.keene.co.uk
Audio
KLAB In-Wall Amplifiers
You quite often want to listen to some music in other rooms in your house, such as
kitchens, bedrooms bathrooms & studies. The problem usually is space. You can fit flush
mount loudspeakers into ceilings and walls without much difficulty but that still leaves
the problem of where to put the amplifier. To solve this problem Keene designed the
KLAB series of in-wall audio amplifiers built into a standard two gang pattress. These will
fit flush to the wall (or can be surface mounted if preferred) and deliver 2 x 20W RMS of
amplification. That's a proper, true 20W RMS of power as well unlike most of the
ridiculous "maximum" or PMPO ratings you commonly see quoted, a true 20W RMS
delivers enough power to satisfy even the most party-inclined teenager.
The recommended power supply for the KLAB series is rated at 15v DC a 4.0. The KLAB
amplifiers can also be powered from a 12v DC supply (for easy use in boats, caravans &
motor homes) although the maximum output power will be slightly reduced.
There are three models in the range; Analogue, Digital and Bluetooth.
KLAB Analogue Models
The Analogue models are built into a metal two gang
pattress. The line level audio input connection is direct
to the PCB at the rear, and control is via infra red
remote control.
Features:
KLAB20
analogue
The KLAB & KLABF amplifiers can be configured
via PCB links to operate in fixed gain mode for
commercial and industrial applications. This enables
the amplifier to perform at a predetermined level
(usually 100%) as soon as power is applied.
GREAT
VALUE
Code KLAB20
(Amplifier & Remote)
Code KLABKIT
(Amplifier, PSU & Remote)
Code KLABPSU
(15v DC 4A power supply)
£87.00
£111.00
£29.99
The Keene KLAB can be purchased with either a
white or a translucent frosted style front panel.
KLAB20F
analogue
• 20 RMS per channel output
• Rear line level audio input
• Infra Red remote control
Code KLAB20F
£87.00
£111.00
£29.99
(Amplifier & Remote, frosted)
Code KLABKITF (Amp, PSU & Remote, frosted)
Code KLABPSU
(15v DC 4A power supply)
KLAB Digital Models
The Digital models Class D Amplifiers for maximum
efficiency. This design allows the PCB to be mounted
directly onto the front panel rather than built into the
pattress as with the analogue version. In addition to the
rear line level input this model also incorporates a front
(jack socket) audio input and built in FM radio with a
ten channel memory.
KLAB20D
digital
£125.99
£149.99
£29.99
Code KLAB20D (Amp & Remote, grey)
Code KLABKITD (Amp, PSU & Remote, grey)
Code KLABPSU
(15v DC 4A power supply)
The Keene KLAB20D can be purchased with either a
grey or white fascia surround.
Features:
• 20 RMS per channel output
• Class D digital circuitry
• Built in FM Radio
£125.99
£149.99
£29.99
Code KLAB20DW (Amp & Remote, white)
Code KLABKITDW (Amp, PSU & Remote white)
Code KLABPSU
(15v DC 4A power supply)
• Front 3.5mm input jack for MP3 players
• Rear line level audio input
• Push button or IR remote control
• Smooth tactile moisture resistant front panel
• Flush mount or surface mount (25mm depth)
KLAB20DW
digital white
KLAB Bluetooth Digital Models
These models add Bluetooth capability to the KLAB
Digital Amplifiers so you can stream audio wirelessly
from your phone or tablet.
• Smooth tactile moisture resistant front panel
• Flush mount or surface mount (25mm depth)
Features:
• 20 RMS per channel output
• Bluetooth connectivity
• Class D digital circuitry
• Built in FM Radio
Code KLAB20DB (Bluetooth Amp & Remote, white) Code KLABKITDB (Bluetooth Amp, PSU & Remote white) £149.99
£179.99
KLAB20DB
The Bluetooth KLAB20DB can be purchased with either a
grey or white fascia surround.
• Front 3.5mm input jack for MP3 players
• Rear line level audio input
• Push button or IR remote control
Code KLAB20DBG (Bluetooth Amp & Remote, grey)
bluetooth white
Code KLABKITDBG (Bluetooth Amp, PSU & Remote, grey)
£149.99
£179.99
KLAB20DBG
bluetooth grey
KLABPSU
worldwide input
2
KRC1
remote control
Email your order to us at sales@keene.co.uk
Audio
Architectural Speakers for use
in Walls or Ceilings
Moisture Resistant Speakers
for use in Walls or Ceilings
•Pivotal tweeters allow high frequencies to be
focussed
• Removable mesh grills
• Frame allows for ceiling or wall board mount without
extra brackets
• 8 ohms
High quality moisture resistant speakers suitable for PA
installations in swimming pools, bathrooms, shower
rooms, saunas and tanning rooms etc.
203mm Circular CMS5U
• Frequency response:
80Hz - 20kHz
• Power: 25W RMS
• Overall Diameter:
203mm
• Panel cut out: 165mm
• Sound pressure level:
89dB
£69.99
£89.99
Code CMS5MR (per pair)
Code CMS8MR
(per pair)
254mm Square B414C
• Frequency response:
40Hz - 20kHz
• Power: 90W RMS
• Overall Dimensions:
254x254x87mm
• Cut-Out Dimensions:
219x219mm
• Moisture Resistant Design
Rectangular Subwoofer B415A
Subwoofer B403A
(per pair)
(single speaker)
£34.99
£34.99
Single Speaker with
Dual Coil & Stereo
Connections
Ideal for smaller
installations where you
don't really have the
room or need to fit
two loudspeakers, this
provides both left and
right stereo channels
from a single point,
whilst maintaining
channel separation.
The speaker has twin
connections so you
simply run both left
and right speaker
cables to it.
Code B414C (per pair)
Code B403A
(single speaker)
• 4" Full Range Mini Box
Speaker System
• Dual Cone Full Range Speakers
• 12 Oz Shielded Magnet
• Power 80 W Max
• Quick Connect Speaker Terminals
• Dimensions (mm) 120x120x132
• Impedance 8 Ohms
• Power 40W RMS
• Frequency Response 80Hz-20kHz
£39.99
£27.99
Amplifier kit with
Speakers Special Offer
KLABKITD plus a pair of CMS5U
Code KLAB20DC5 KLABKITD plus a pair of CMS8U
(single speaker)
Bookshelf Speakers
High quality 4" dual cone,
full range mini box speakers.
Solid ABS Construction with
Quick Connect Speaker
Terminals.
PACKAGE DEAL
• Frequency response:
70Hz - 20kHz
• Power: 25W + 25W RMS
• Overall Dimensions: 227x86mm
• Cut-Out Dimensions: 193mm
• Impedance 2 x 8 Ohms
Code CMS65S (15v DC 4A power supply)
£34.99
£39.99
• Frequency response:
30Hz - 4kHz
• Power: 220W (max)
• Overall Diameter: 268mm
• Panel cut out: 232mm x 177mm
deep
• Impedance 8 Ohms
• Moisture Resistant Design
• Frequency response:
30Hz - 3kHz
• Power: 90W RMS
• Overall Dimensions:
367x367x88mm
• Cut-Out Dimensions:
329x329mm
• Impedance 8 Ohms
Code B415A
Code KLABPSU
• Frequency response:
80Hz - 20kHz
• Power: 40W RMS
• Overall Diameter:
180mm
• Panel cut out: 132mm
• IP35 rated
Rectangular B411A
• Directable Titanium dome
tweeter
• Power: 50W RMS
• Overall Dimensions:
305x218x77mm
• Cut-Out Dimensions:
275x185mm
• Frequency response: 80-20kHz
Code B411A £109.99
£129.99
£29.99
Code KLAB20DS (Amplifier only)
180mm Circular CMS8MR
• Frequency response:
60Hz - 20kHz
• Power: 30W RMS
• Overall diameter 273mm
• Panel cut-out 238mm
• Sound pressure level: 90dB
Code CMS8U
• Frequency response:
80Hz - 20kHz
• Power: 35W RMS
• Overall Diameter:
148mm
• Panel cut out: 112mm
• IP35 rated
If you are sending a line level signal to a room then
sometimes you'll have direct control of the source and
just want to amplify the audio signal in the room
without needing any other form of control. The Keene
KLAB20DS slave amplifier will do this job perfectly. It is
designed to be a fit and forget solution to powering
additional and remote pairs of loudspeakers. Once
installed it will automatically switch on whenever audio
is detected and switch back again to an ultra-low
power standby mode when no audio signal is present.
Ideal for feeding line outputs from from say
Squeezebox, Sonos etc.
Code KLABKITDS (Amplifier & PSU)
273mm Circular CMS8U
Code CMS5U
148mm Circular CMS5MR
Digital In-Wall Slave Amplifier
£29.99
Code KLAB20DC8 Code B406A BLACK (per pair)
Code B405A
WHITE (per pair)
£18.99
£18.99
HQ Wall mounted loudspeaker
volume control
Suitable for UK standard electrical double pattresses
(47mm deep). White facia with chrome colour knob.
High efficiency (transformer) design with max power
handling of 60W rms. Will accept cable up to 2.5mm
dia. Connect in-line between amplifier and speaker.
£189.99
£229.99
Find product information and data sheets on www.keene.co.uk
Code BT936
24.99
£
3
Audio
Wireless Audio Sender
Wireless Speakers
A Sender/Receiver pair designed to transmit audio
wirelessly around your house. Take the line (or
headphone) output from your PC, TV or music system
and sonnect it the Sender, then connect the line
output from the receiver back into the remote amplifer
in the room you want to listen in. The sender and
receiver will automatically pair so there's nothing to
configure. Additional receivers can be added for a oneto-many solution.
£51.95
£32.95
Code AA625 (Sender & Receiver Pair) Code AA625R (Additional Receiver) 2-Way Speaker Selector Switch
The B-Tech BT12 Allows a second pair of loudspeakers
to be connected to your amplifier with switch select
for either pair or both. (screw terminal connections
suitable for cable up to 2.5mm diameter.
Features:
• Designed to allow the use of two pairs of speakers
with one amplifier
• Speaker selector switch to play either pair of
speakers or both at the same time
• Suitable for loudspeakers from 4ohms to 16ohms
• Screw terminals for strong connection and
minimal loss
• Strong, stylish metal casing
• Accepts loudspeaker cable up to 2.5mm diameter
• 150 watts RMS per channel rating
Code BT12
• Enjoy your complete music collection anywhere in
and around your home (bath room, kitchen, shed,
etc.) wirelessly
• Garden party, BBQ or a romantic evening with just
the two of you on the balcony? Create the perfect
atmosphere with matching music
• Optimal music perception through high quality, omni
directional two-way audio technology. The sound is
spread 360°
• The speakers are splash-proof and fine for use in
the bathroom
• Because of the wireless technology you can place the
speakers wherever you want. Because of the optional
battery power you don’t even need a socket
• Use your iPod, radio or anything with a headphone
socket as the source
• Easy to install and to use; automatic frequency tuning
and maintenance because of Auto Tuning and PLL
function
13.99
£
8-Way Speaker Selector Switch
This switcher unit allows the distribution of a stereo
amplifier. Simply connect the speaker output of an
amplifier to the box, this output can then be distributed
to up to eight different stereo speaker sets in eight
different locations, each speaker set can be individually
activated via the push buttons on the front of the box.
Ideally suited for buildings where an independent sound
control is required for different rooms or zones. Enables
eight pairs of speakers to be connected to a single stereo
amplifier.
Code SA352U
• Spring clip terminals
• Designed for 4-16 ohms speakers
• Wiring Gauge 14 to 22 gauge
• Input 1 x stereo
• Output 8 x stereo
• Power per channel 100W max
• Dimensions 432 x 125 x 55mm
• Weight 2.08kg
Speaker Outlet Wall Plates
Twin 4mm Binding Posts
Wall outlet plate with 2 pairs of
colour coded gold plated binding
posts. Fits a standard one gang
patress. Solder tag connection
on rear.
Specifications:
• Heavy duty push-buttons
• Built-in overload protection
Code 8WLS
29.00
£
2x4 Speaker Matrix Switch with Volume Control
This matrix switcher for stereo amplifiers has 2 inputs
and 4 outputs. Any of the inputs may be routed to any
of the outputs, or the same input may be routed to all
outputs or any combination. Simply connect the
output of the amplifiers to the inputs, these inputs can
then be routed to four different stereo speaker sets in
four different locations, each speaker set can be
individually activated via the push buttons on the front
of the box and individual volume controls.
Enables four pairs of speakers to be connected to two
separate amplifiers.
• Accepts up to 14 gauge speaker cable
• Individual A/B switch per zone
• Wiring Gauge14 to 22 gauge
Specifications:
•Inputs: 2 x stereo
• Outputs: 4 x stereo @ 4 to 16 ohms
• Power per channel: 100W max
• Dimensions: 432 x 133 x 64mm
• Weight: 3.67kg
Single 4mm Binding Posts
Wall outlet plate with a single pair
of colour coded gold plated
binding posts. Fits a standard one
gang patress. Solder tag
connection on rear.
£9.99
Wall outlet plate with a single pair
of loudspeaker spring clip
terminals. Fits a standard one
gang patress. Solder tag
connection on rear.
Code HCP16
Code 24LMS
£11.99
Single Spring Clip
91.00
£3.99
Twin Spring Clip
£
Wall outlet plate with two pairs of
loudspeaker spring clip terminals.
Fits a standard one gang patress.
Solder tag connection on rear.
Wireless Surround Speaker Connection Kit
Connect your present home cinema rear speakers
wirelessly; no more loose cables in your living room.
Uncompressed digital transfer ensures sound that goes
beyond CD quality, without interference or delay.
The built-in amplifier in the receiver provides more than
enough power for your rear surround speakers. Automatic
ON/OFF function of both transmitter and receiver for
trouble-free use. The volume is adjusted with your own
remote, because the transmitter is directly connected to
the speaker output. Local volume on transmitter and
receiver for the correct balance between front - and
rear speakers.
Code HCP17
£5.99
Twin 4mm Socket
Wall outlet plate with two pairs
of "banana" type 4mm
loudspeaker sockets. Fits a
standard one gang patress.
Solder tag connection on rear.
Code SA220
4
Code HCP20
Code HCP5
Features:
• Heavy-duty push-buttons
• Built-in overload protection
• Designed for 4-16 ohm speakers
• Black aluminium housing
• Individual volume controls with black
aluminium finish
72.00
£
98.96
£
Code HCP18
Email your order to us at sales@keene.co.uk
£4.99
Audio
Bluetooth Audio Adaptor
Digital Audio Lip-Sync Corrector
A fantastic gadget, simply pair it with any Bluetooth
audio source, plug the output into any device with an
auxiliary input and listen to internet radio or the music
stored on your smartphone or tablet PC on your audio
system (wirelessly). Suitable for all Bluetooth® enabled
sound sources such as iPhone, Android phone, iPad,
etc. Works with all audio installations, iPhone dock or
radio/CD player with aux-in, line-in or mp3-link
connection. Supports A2DP Stereo Bluetooth for music
in CD quality. It also works great with the Keene
KLABKITD (previous page).
The definitive answer to lip sync error for up to four
sources! Do you sometimes get frustrated by the lipsynch errors when viewing? It occurs because of a
delay introduced by the processing of the picture. The
audio doesnt go through the same processing hence
the audio appears ahead of the image. If you use an
AV amplifier for your sound then we have a solution the Felston DD740 digital audio delay module. It
allows easy adjustable audio delay allowing you to get
everything back in perfect sync. There are four inputs
and you can switch and adjust from your armchair
with the supplied remote.
Specifications:
680ms delay (340ms for 96kHz signals)
On-the-fly adjustment with no image overlay
• Support multiple pair:
Up to 8 devices
• Range: Up to 10
metres free field
• Interface audio output:
3.5mm male jack
• Power: Mini USB or
battery
• Battery: Li-ion:
140mAh, Stand-by
time up to 140 hours,
Working time up to
6 hours
• Energy Saving:
Automatic switch-off if
no connection within
ten minutes
Code BB75
28.90
Code DD740
£
Sound Level Meter
Digital Display
How well set up is your home cinema system?
How low does your subwoofer go? Find out for
certain with a sound level meter. Great value for
money, this gives you the accuracy you need to
fine tune your system.
• Built in microphone
• Seven selectable frequency
ranges
• Phono output (for
connection to
external equipment).
• FAST & SLOW response
settings
• Weighting selector ‘A’ for
Human ear bias or ‘C’ for
full frequency range
• Peak level hold
• Easy to read 21-bar
graphical display
• Size (approx):
159 x 64 x 48mm
• Power: PP3 type
9v battery
Code SLM2055
(not supplied)
Tweaking in 1ms and 1/3ms steps
36 preset delays for instant recall
Fully featured remote control with numeric keypad for
discrete delay entry
Discrete input switching, with input's last delay
restored
Automatic optical-to-coax/coax-to-optical conversion
4 digital audio inputs, 2 digital audio outputs (optical
and coax)
Adjustable display brightness
Discrete IR commands for integration with learning
remotes
No effect on audio quality thanks to bit-perfect
reproduction
4x1 Digital Audio Switch
Harmony Headphone Amplifier
The AU-D41 Optical Audio Switcher has four optical
inputs and one optical output. This device allows users
with multiple optical sources connection for one output
display. All signal are bypassed without delay. The
device has last memory function and IR remote control
The Harmony Headphone Amplifier takes line level input
and provides stereo headphone amplification. It can be
controlled via IR remote or front panel push buttons. It
can be used for any purpose where line stereo level
audio is required to be amplified to headphone level. It
is particularly suited to TV viewing applications, where
one person listening via headphones can set their own
personal volume without affecting the normal audio
output for anyone viewing normally.
Features:
• 4 input digital optical audio switcher.
• Optical sampling rate supports up to 192 kHz.
• Up to 24bit resolutions.
• Low power consumption.
• PCM2, AC3/5.1, Dolby 5.1 & DTS 5.1 pass through.
•Amplifies Optical (Toslink) output, extending another
5 metres.
• Supplied with IR remote control.
39.99
£
Audio Ground Loop Isolator
A low level filter designed to isolate the ground
between source and amplification to prevent noise or
hum. Can be used for in-car applications to eliminate
alternator and engine noise or any audio installation
that suffers from ground loop (mains) hum. Simple inline connections (phono plugs to phono sockets) make
for easy installation and no external power is required.
Gold plated connections.
169.00
£
Code AUD41
Specifications:
• Audio Input: 2 x RCA phono
• Audio output: 1 x 3.5mm stereo jack socket
• Power: 12V DC 200mA (UK mains adaptor supplied)
• Dimensions: 90 x 76 x 44mm
• Weight: 170g (exc. cables & supply)
61.37
£
Coaxial/Toslink to L/R Stereo
Audio Convertor
This neat audio convertor will convert the selected
switched signal, either coaxial (RCA) or optical (Toslink)
and convert the digital signal to analogue audio with a
left and right output.
Specifications:
• Input: 1 x Toslink (Fibre Optic) & 1 Coaxial (RCA)
• Outputs: 2 x RCA’s (Left and Right)
BULK PRICING (50+) and
OEM AVAILABLE on this product
Code AGLI
6.99
£
Code AUD3192
49.51
£
Find product information and data sheets on www.keene.co.uk
Code HHAMP
54.99
£
5
Audio
HDMI Audio Embedder with
built in Repeater
Analogue Audio Lip Sync Corrector
This analogue stereo Lip Sync Corrector is a small
device for delaying audio signal to overcome audio
sync issues. The AU-D18 Lip Sync corrector is able to
adjust the timing to the display/amplifier so that users
may received both video and audio in sync. No more
annoying sound mismatch. The Lip SyncCorrector is
easy to use with a simple setup and an affordable unit
for sound delaying.
Specifications:
• Inputs 2 x Analogue Audio (L/R stereo)
• Outputs 2 x Analogue Audio (L/R stereo)
• Power 5V/1A DC
• Dimensions 45(D) x 45(W) x 25(H)mm.
The AU-11CA Audio Embedder lets you insert an external
audio signal into any HDMI source. The device allows you to
insert analogue or digital stereo and multi-channel digital
surround sound signals (via Optical) to give users the
capability to overcome audio issues within complex HDMI
installation. The AU-11CA also repeats the HDMI signal to
allow an extended total HDMI cable range.
Features:
Features:
• Compliant with HDMI v1.3 , HDCP 1.2 and DVI 1.0
• Lip Sync corrector with adjustable delay between
0 & 300ms
• Sample Rates 48 kHz
• Analogue to analogue signal bypass
• Low power consumption
• Supports Optical Sample Rate up to 96 kHz
Code AUD18
63.25
£
AU-11SA Audience HDMI Audio De-Embedder Repeater
The AU-11SA is an advanced solution for HDMI to
HDMI repeating with Audio de-embedding. It is
compatible with v1.3 HDMI specifications, a cutting
edge technology which defines the transfer of deep
colour (12 bit) video with a high bandwidth of up to
225Mhz. Connect to source and display (HDMI), select
the required audio format & output your audio format
to your amplifier.
Features:
• Compliant with V1.3 HDMI, HDCP 1.1 and DVI1.1
• Decodes HDMI audio to analogue and digital
• Corrects digital error and automatically provides
equalisation up to 40dB
• Supports high definition input up to 1080p
– output resolution follows input
• Supports HDMI signal amplification and equalisation
output for repeater function – can be used to extend
up to 35m
• Supports up to 24bit resolution digital audio
• HDMI cable distance testing showed that with 1080p
8bit/12bit resolution, the input/output distance is up to
10 meters
• Low power consumption
• Supports HDMI Sample Rates up to 192 kHz
Specification:
• Inputs 1 x HDMI, 1 x Optical, 1 x Analogue Stereo (2 x
RCA)
• Outputs 1 x HDMI
• Power 5V/1A DC (US/EU standards, CE/FCC/UL certified)
• Supports uncompressed digital LPCM 7.1 / 5.1 or
2 channels & compressed digital Bitstream through
HDMI input and output ports
• Supports LPCM 7.1 / 5.1 or 2 channels output
through multi-channel output ports
• Supports digital Dolby 5.1/ 2 and LPCM 2 channel
output through Optical Toslink
Code AU11SA
• Dimensions 85(D) x 85(W) x 35(H)mm
129.41
£
Features
Digital Audio over CAT6
• Supports LPCM Stereo, DTS and Dolby Digital via Optical
input
• Supports Coaxial or Optical digital audio SPDIF signals
The PU-304-KIT is designed to send digital audio signals
• Supports Stereo and Multichannel digital audio (LPCM,
over 150m. This device supports both Coaxial and
DTS, Dolby Digital, Dolby Digital Plus)
Optical signals and can transmit these signals up to
• Supports sample rate up to 96kHz
150m. The PU-304-KIT can be powered using a USB
cable or the supplied PSU adaptor for added flexibility in • Dual transmission 1 x Coaxial and 1 x Optical
a compact design. Digital SPDIF signals are supported • Signals can be extended over single CAT5e/CAT6
up to 150m
up to a sample rate of 96Khz, and support for Stereo
and Multichannel digital audio (LPCM, DTS, Dolby
• Power 5V/1A, DC (US/EU standards, CE/FCC/UL
certified)
Digital, Dolby Digital Plus), also provided.
• Dimension: PU-304RX) 55mm (W) x 85mm
(D) x 22mm (H) (PU-304TX) 55mm (W) x 85mm
(D) x 22mm (H)
122.31
£
Code AU11CA HDMI Audio De-Embedder (5.1)
with built in repeater
The AU-11CD is an advanced solution for repeating HDMI
with integrated Audio de-embedding, up to 5.1. Connect
the AU-11CD between your source and display via HDMI,
and select the audio format required.
Features:
• Compliant with v1.3 HDMI, HDCP 1.2 and DVI 1.0
• Supports HDMI Sample Rates up to 192 kHz
• Supports Optical Sample Rate up to 48 kHz
• Supports TMDS clock frequency rate 225MHz
• Supports high-bit-rate (HBR) audio
• Input and Output HDMI cable length can run up to 10m
at 1080p 8bit resolution
Code PU304
Digital audio convertors
Convert digital optical audio signals (TOSlink) into RCA
coaxial (S/PDIF) and vice versa.
Dimensions: 20mm x 71mm x 46mm
Power supply 6vDC 250mA (included)
115.44
£
DAC Digital to Analogue audio
with USB interface
DAC with USB audio interface and headphone
amplifier. The most affordable and effective way to
upgrade any CD/DVD player, computer, games console
or network device to high-end sound quality. The DAC
has one optical, one coaxial, and one USB inputs for
up to three digital sources.
• Low power consumption
• Support built-in audio EDID switch of LPCM2, 5.1/7.1
or Bitstream
• Supports 3D signals
Specification:
• Inputs 1 x HDMI
• Outputs 1 x HDMI, 1 x Optical (Toslink), 2 x Analogue
Audio L/R (RCA)
• Power 5V/1.2A, DC (US/EU standards, CE/FCC/UL
certified)
• Dimensions 90mm (W) x 85mm (D) x 35mm (H)
DAC is the ideal convertor for music lovers seeking an
excellent value upgrade to 24 bit advanced HD (high
definition) audio.
Code KAOC
optical to coaxial
Code KACO
coaxial to optical
6
£19.99
£19.99
Code DAC £39.00
Email your order to us at sales@keene.co.uk
Code AU11CD 122.31
£
Audio
HDMI Audio Extractor
HDMI Audio Amplifier
The HDMI Audio Extractor is a device that allows you to
extract audio signals from your HDMI source. When
connecting with a TV or display you dont always get great
audio, or in the case of a display, no audio at all, so with
this Audio Extractor you can take your original HDMI audio
signal and convert it to Digital Toslink or analogue L/R
audio. What this means is that you can output your audio
signal to external speakers or extend your audio signal, the
HDMI Audio Extractor is the perfect choice.
This is effectively an HDMI switcher that allow you to
embed or de-embed audio from multiple sources. It
delivers a powerful 30W per channel and has IP
connectivity for easy ipad/tablet control. Well worth a
look for any AV multi-room installation.
Features:
Compliant with HDMI 1.3, HDCP 1.2 and DVI 1.0
• Outputs: 1 x HDMI, 1 x Optical, 1 x Digital Co-Ax,
Features:
• 30W per channel digital stereo Amplifier
• Inputs: HDMI x 2, 1 x L/R Stereo audio, 1 x Optical,
1 x Digital Co-Ax, 1 x 3.5mm Stereo
1 x L/R Stereo (Line Level output), Speaker Terminals
• Control via remote control, RS-232 or IP (Web GUI
Supports HDMI Sample Rates up to 192 kHz
or Telnet)
Supports Optical Sample Rate up to 48 kHz
• Dedicated Microphone input for commercial
Supports TMDS clock frequency rate 225MHz
• Supports Digital to Analogue (DAC) and Analogue
1x 3.5mm Stereo mini-jack [1x Analogue - Stereo(L/R)]
1x RJ45 [1x IP Control]
1x 3.5mm Stereo mini-jack [1x Infra Red Receiver]
1x 9pin Dsub [1x RS-232 Data]
Outputs 1x HDMI [1x HDMI Uncompressed AV and
Data]
1x Toslink [1x Optical - 2 Channel LPCM]
1x RCA [1x Coaxial - 2 Channel LPCM]
2x RCA [1x Analogue - Stereo (L/R)]
4x Speaker Binding Posts [1x Speaker Level Stereo
Output]
PSU: 24V/4.16A
Dimensions 255mm [W] x 170mm [D] x 48mm [H]
application
to Digital (ADC) conversion
Supports high-bit-rate (HBR) audio
HDMI cable distance testing showed that with 1080p 8bit
resolution, the input & output can run up to 15 meters
• Simultaneous audio outputs
• Compact design for remote application
Low power consumption
Specifications:
Supports built-in audio EDID switch of LPCM2,5.1/7.1
or Bit stream
Inputs 2x HDMI [2x HDMI Uncompressed AV and Data]
1x XLR [1x Microphone]
1x Toslink [1x Optical - 2 Channel LPCM]
1x RCA [1x Coaxial - 2 Channel LPCM]
2x RCA [1x Analogue - Stereo (L/R)]
395.03
Code AUA300
£
Code AUA300HBT
£
HDMI Audio Amplifier with HDBaseT
Specifications:
Input Port 1 x HDMI
HDMI Sample Frequency Up to 192 kHz
Optical Sample Frequency Up to 48 kHz
Output Ports: 1 x HDMI, 1 x Optical, 1 x analogue L/R
HDMI Audio Format: PCM2/5.1/7.1, Dolby 5.1, DTS 5.1,
DD+, D-True HD, DTS-HD
All the features of the AUA300 above with the added
benefit of integrated HDBaseT input and output. This
means it can be used for creating additional HDBaseT
zones or used to repeat the signal to further HDBaseT
2-Channel Digital AV Receivers.
Optical Audio Format: PCM2, Dolby 5.1, DTS 5.1
L/R Audio Format: LPCM2
574.61
HDMI Scaler Audio Cross Convertor
Code HDMIAE 59.99
£
Audio Only Source to HDMI
Bridge
The AU-11HB Audio Source to HDMI Bridge is designed
integrate audio only sources into HDMI video distribution
systems. It will accept digital (optical) or analogue (L/R
Stereo) audio signals and output them over HDMI. This
clever device also adds a 'blue-screen' video feed into the
HDMI signal path so that any HDMI AV receiver or display
will accept the audio signal for sound reproduction. It
allows audio from any source to be easily integrated into a
HDMI system, very useful when distributing via an HDMI or
HDBaseT matrix, great for systems such as SONOS etc.
1T-VS-658 Video Scaler is a professional Up and Cross
Convertor with an HDMI output. Fully scaleable video
inputs include HDMI, DVI (via the HDMI connector),
Analog RGB/YPbPr via an HD-15, Analog YPbPr or
480i/576i YUV Component via three RCA, YC and
Composite Video. It handles I/O Resolutions up to
1080p and WUXGA. Both digital and analog audio
processing is supported and audio delays of up to
150ms can be introduced to insure lip sync. Five
Analog Stereo and a SPDIF Coaxial Digital Audio input
can be selected for embedding into the HDMI output.
A separate Coaxial Digital Audio output is also
provided. Advanced features, such as 3D Motion
Adaptive De-Interlacing, 3D Noise Reduction and 8-bit
triple ADC/PLL technology, combine to provide
extremely high quality signal conversion. The HDMI I/O
is HDCP Compliant. An OSD (On Screen Display) menu
makes the 1T-VS-658 easy to set up. Control is via
front panel joystick and buttons, Infrared Remote (via
optional IRC-5) or RS-232 interface.
Features:
Composite Video 1x via RCA Connector
Audio Inputs:
Digital (S/PDIF) 1x via RCA Connector
Analog Stereo 3x via RCA (R/L)
2x via 3.5mm Mini-Stereo
Video Output:
HDMI v1.2 (RGBHV) 1x via HDMI Connector
Audio Outputs:
Embedded into HDMI Digital per HDMI Spec
Digital (S/PDIF) 1x via RCA Coax Connector
Audio Delay Adjustment Off, 40ms, 110ms, 150ms
Input Video Formats Supported
HDMI v1.2 (RGBHV/YPbPr) Up to WUXGA, 1080p
Analog RGBHV Up to WUXGA@60Hz
Analog YPbPr Up to 1080p
Analog Interlace Component 480i, 576i YUV
DVI (via HDMI Connector) Up to WUXGA, 1080p
Composite and YC (S-Video) NTSC or PAL
HDMI Output Resolutions to WUXGA and 1080p
Inputs: HDMI, RGB, YPbPr, YUV, YC (S-Video), CV
Both Analog and Digital Audio Capable
Audio Delay for Lip Sync Corrections
3D Motion Adaptive De-Interlace & Noise Reduction
3:2 Pull-Down w/2:2 Pull-Down Recovery
Infrared Remote Control (optional IRC-5)
Specifications:
Code AU11HB 164.64
£
Video Inputs
HDMI (DVI Compatible) 1x via HDMI Connector
Analog RGBHV/YPbPr 1x via HD-15 Connector
Analog YUV Component 1x via 3x RCA Connectors
YC (S-Video) 1x via 4-pin Mini Din
Code 1TVS658 Find product information and data sheets on www.keene.co.uk
410.11
£
7
AV Switching & Distribution
Keene KPDA 1:5 Component Video & Audio Distribution Amplifier
• One input, five fully buffered outputs
• Wide bandwidth HDTV capable
•Broadcast quality high speed video buffers
•Use for component video, RGBs video, RGsB video
or four x composite video plus stereo audio
•One video channel may be used for digital audio
The KPDA is a high quality audio/video distribution
amplifier, allowing one video and audio source to
simultaneously supply up to five other devices. It uses
very high quality high bandwidth ICs to ensure that
each output is not discernible from the input, making
it ideally suited to driving multiple displays or making
multiple copies from one source. There are two stereo
audio channels and four video channels, making it
suitable for use with component video, RGBs video,
RGsB video or 4 x composite video plus audio. Any of
the video channels can also be used for digital audio
if desired.
• Unity gain
• Dimensions: 220mm x 104mm x 43mm
• Weight: 780g (excluding power supply)
Specifications:
• Power requirements: by external supply to DC input
socket, (2.1mm centre positive) 12-18v DC @
300mA or greater
• Video: 5 buffered video outputs bandwidth 75MHz
(up to 1080p)
• Level - composite / luminance 1v pp, chrominance
0.3v peak to peak
• Distortion components <–50db up to 10MHz
• Open circuit voltage gain is X2 (unity gain when
correctly terminated)
• Back terminated series 75 Ohm outputs for
reflection free performance
• DC coupled on all outputs
• Slew rate up to 500v/uS
• Audio: 5 buffered audio outputs
• Distortion <0.1%
• Bandwidth 20Hz – 30kHz
• Output impedance, <1k ohm each output
• Input impedance >10K ohm
59.99
£
Code KPDA
Keene SDA 1:5 Scart Distribution Amplifier
One input to five outputs, fully buffered using
broadcast grade video amplification ICs. Pin 8 is routed
through (if the input goes high all the outputs go
high) and every pin connection is carried through
making it suitable for composite, S-video, component
or RGB. Supplied in a robust metal case this is ideal for
displaying one signal on multiple TVs or for making up
to five simultaneous copies from one source. Mains
adaptor included.
BULK PRICING (50+) available for
all products on this page
Specifications:
• Power: 12-18v DC @ 300mA
• Video: 5 buffered video outputs
• Video bandwidth: 50MHz
•Video level: Composite / Luminance 1v pp,
Chrominance 0.3v peak to peak.
• Video distortion: < -50db up to 10Mhz
• Back terminated series 75R outputs for reflection
free performance
• DC coupled on all outputs
• Slew rate up to 500v/uS
• Audio: 5 buffered audio outputs
• Audio distortion: <0.1% Bandwidth 20Hz - 30KHz
• Audio output impedance: <1K ohms each output
• Audio input impedance: >10K ohms Unity gain
• Dimensions 219 x 115 x 37mm
• Weight 725g (exc supply & cables)
Code SDA
UK model with UK 3-pin
mains plug order
£99.99
Code SDAE
Euro model with round 2-pin
mains plug order
£99.99
Keene KDA 1:4 AV Distribution Amplifier
The Keene KDA distribution amplifier has one set of inputs for composite video, s-video and stereo audio and four identical sets of outputs, each output being
indistinguishable from the input.
Uniquely, the Keene Distribution Amp also has a switchable line drive feature, giving the ability to send audio and/or video over much longer cable runs than normally
possible (up to 100m dependant on cable). The KDA may be ‘daisy-chained’, that is to say the output of one KDA may be fed into the input of another. Used in such a
configuration, five KDA’s may be used to provide up to 16 AV outlets from one AV input.
This product is ideal for:
Sending an AV signal to multiple displays
Sending an AV signal down a long cable run (up to 100m with the right cable)
Making up to four simultaneous recordings from one source
Sending line level audio to amplifiers in other rooms
Specifications:
• Power: 12-18v DC @ 300mA or greater (mains adaptor included)
• Video bandwidth: 50MHz distortion: <50db up to 10Mhz
• Back terminated series 75ohm outputs for
reflection free performance
• DC coupled on Composite video and Luminance outputs
• AC coupled on Chrominance output
• Slew rate up to 1000v/uS
• Audio distortion: <0.1% bandwidth: 20–30kHz
• Audio output impedance: 1K ohms each output
• Audio input impedance: >10K ohms
• Dimensions 144 x 111 x 64mm
• Weight 680g (exc supply & cables)
Code KDA
8
Email your order to us at sales@keene.co.uk
84.99
£
AV Switching & Distribution
HDMI Distribution Amplifiers
HDMI Distribution Amplifiers
Each product in the Quantum Distribution Amp Series
is compatible to V1.3 specifications. Besides splitting
and distributing, this HDMI V1.3 Distribution Amplifier
also does signal amplification and equalization, so as to
provide high performance for both audio and video.
These Coosis HDMI Distribution amplifiers are compact devices that give multiple simultaneous HDMI outputs from one
HDMI input, ideal for viewing on multiple displays. The units can also be cascaded together in a “pyramid” network to
provide a one-to-many solution.
Features:
P lease note: If the max resolutions of your displays are different, the EDID functionality will detect all the connected
displays’ EDID information and auto-match the output resolution to the lower one. For example, if one display supports
720P resolution and the rest support 1080P, the signal will be lowered to 720p for all displays.
•Compliant with HDMI 1.3, HDCP 1.1 and
DVII.0 standards
•Supports a wide range of PC and HDTV resolutions
from VGA to UXGA and 480i to 1080p
•HDCP keysets allow each output to work
independently when connecting to a HDMI display.
HDMI cable distance test with 1080p resolution at
30 metres for both video and 5.1 audio when using
quality cables
•HDCP Compliant
•Supports DVI source and DVI display by using DVI to/
from HDMI adaptor/cable
Code QU12S 1 input to 2 outputs
Code QU14S 1 input to 4 outputs
Code QU18S 1 input to 8 outputs
Blu-ray
3D
Compatible
£148.04
£287.30
£415.79
CYP HDMI 1 to 8 Distribution
Amplifier with System Reset
Each splitter in the Quantum Distribution Amplifier Series is
compatible to v1.3 HDMI specifications, supporting ‘Deep
Colour’ together with High Definition Audio. Each buffered
output can run 1080p up to 15 metres and can also be
cascaded.
Features:
• v1.3 HDMI, HDCP 1.1 and DVI 1.0 compliant
• HDMI 1 to 8 Splitter with System Reset function
• Resolutions supported: PC - VGA to UXGA; HDTV - 480i
to 1080p plus 1080p24fps
• High Definition Audio supported: Dolby TrueHD, Dolby
Digital Plus and DTS-HD Master Audio plus LPCM
• Auto signal amplification & equalisation improves signal
transmission distances
• Supports CEC bypass
• Supports ‘Deep Colour’ (10, & 12)
• Selectable EDID settings - TV (downstream) and
STD (fixed)
Code HDC12
Code HDC14
Code HDC18
£34.99
£74.99
£114.99
(1 input to 2 outputs)
(1 input to 4 outputs)
(1 input to 8 outputs)
VGA & Audio Cat 5 Extender System
Enables you to transmit VGA signals up to 150M
(500ft.) away with resolution up to 1024 x 768. It
features common mode noise suppression circuit for
superb VGA quality via inexpensive unshielded twisted
pair CAT5 cables. The Local unit duplicates the input
signal for local use and transmits the VGA signal to a
Remote unit. The Remote unit broadcasts the signal to
two VGA outputs. The units also distribute audio
(mono at remote location) Ideal for public
broadcasting, exhibits, retail stores, courtrooms, stock
tickers, bus station and many more applications.
In summary, the local
unit has one input and
two outputs, and the
remote unit has a further
two outputs. Audio is
duplicated in stereo
locally and in mono on
the remote unit.
Specifications:
• Cable between units: CAT5, CAT5e and CAT6
• Max. distance: 50 metres
• VGA input port: HDB15 (female) x 1
• Audio input port Stereo jack (female) x 1
• VGA output port HDB15 (female) x 2
•Audio output ports: Stereo jack (female) for local
unit, x 2 Mono jack (female) for remote unit
• Equalizer selector : 4-position slide switch
• Status indicators: Power (green) x 1,
Active (yellow) x 1
• Operating voltage: 9V DC, 600mA
UK adaptors supplied
99.99
£
Code EVA214
• Power & SYNC LED’s indicator
Component Video Matrix 4:2
• Supports 3D signals
The AVT5842MX is a 4 input by 2 output switcher that
can be used for either YPbPr Progressive Scan Video or
YCbCr Component Video, plus Stereo Audio. It is a
dual output switcher and sends the selected input to
the outputs independently. Since it is a Matrix
Switcher, each of the two outputs can have the same
or a different video signal, selected from the four
inputs. Selection can be made by the front panel push
buttons or by the IR Remote Control.
Specification:
• Input 1 x HDMI female port
• Outputs 8 x HDMI female ports
• Power 5V/5A DC
• Gross Weight 1240g
• Net. Weight 1000g
Code QU8MS
307.65
£
Features and Specs:
• 4 Component Video Inputs via RCA connectors
• 4 Stereo Audio Inputs via RCA connectors
• 2 Individually Selected Component Video Outputs
via RCA connectors
• 2 Individually Selected Stereo Audio Outputs via
RCA connectors
• Works with Progressive Scan YPbPr 480p,
576p, 720p or 1080i Component Video
• IR Remote or Manual Control
• Video Bandwidth: 300MHz
• Size: 1.9" High x 9.3" Wide x 5.7" Deep
(48mm x 230mm x 145mm)
• Weight: 920g
• Power: 12vDC 200mA UK adaptor included
Code AVT5842MX
Find product information and data sheets on www.keene.co.uk
149.99
£
9
RGB Conversion & Distribution
VGA in to HDMI Out
Keene RGB2C RGB/Component
video transcoder
Composite / s-video to
Component or RGB
Another in-house product from Keene Electronics, the
RGB2C can convert an RGB input to a component (Y Pb
Pr) output, and vice versa. It can cater for sync on green
or composite sync input and also provide sync on green
or composite sync output. LED indicators provide useful
information on the type of signals present and which
process is being performed. Designed to be installed inline with the signal path, has SCART input and output
connectors to make connection simple. Supplied
complete with UK mains adaptor and KA150 scart to 3
phono adaptor.
A handy compact unit that will convert either
Composite or S-Video to RGsB or YUV via 3 phono
socket connectors. It automatically recognises any world
standard input: NTSC 3.58/4.43, PAL, PAL M, PAL N &
Secam. The Output format is selectable between RGB
and YCbCr.
Specifications:
• Input: 1 x CV + 1 X SV
• Output: 3 phono - RGsB or YUV
• Power Supply: 5V DC 350mA (adaptor supplied)
• Dimensions: 145 x 90 x 32 mm
The Coosis VGA to HDMI Portable convertor is designed
to be extremely compact in size and ideal for home and
office use or life on the move. Users can plug this
convertor into their desktop, laptop or any device with a
VGA output (must be an RGBHV type signal, not
component or YUV!) and convert easily to HDMI. Great
for watching PC and laptop signals on your big screen TV,
or getting your presentation on to the office projector.
The best thing is that resolutions of less than 1920 x 1200
@ 60Hz don't need any extra power although a USB
power cable is included should you wish to use 1920 x
1200 @ 60Hz. An analogue audio input is included as a
3.5mm stereo socket and this is then output in the HDMI
signal to the display.
* Please be aware that this is only a signal convertor and
not a scaler. The output resolution will be the same as the
input resolution and will not increase the picture quality.
49.99
£
Code VGAHDMIP
HDMI to Composite & S-Video
Down Convertor
Code RGB2C
69.99
£
BULK PRICING (50+) available
Code CPVSRGB
HDMI input to Component (or
RGBHV) & Audio output
This unit will take in HDMI and give out either
Component video (Y, Pb, Pr) or RGBHV (PC signal), plus
spdif or analogue stereo audio. It enables you to
connect your new HDMI sources to older analogue
displays. The convertor is extremely compact in size and
can be plugged directly into a display with VGA
connections or use the supplied cable to connect to a
Ypbpr component video.
74.21
£
RGB to S-Video Convertor
RGB is a great method of sending video, with picture
resolution as good as s-video and vastly superior to a std
composite signal. The problem is not everything can
accept an RGB signal and often composite is your only
option. Well, here’s another problem solved! This Box
can convert an RGB scart output into S-video plus audio.
VS-226 HDMI to CV/SV/Stereo Down convertor changes
digital HDMI signals (or a DVI input signal with S/PDIF
coaxial audio) to NTSC or PAL analogue video signals
and also provides a L/R stereo audio output. Besides
S-Video and Composite Video outputs, it provides a reclocked HDMI signal which delivers a jitter free bypassed
output of the original HDMI signal. In addition, either a
bitstream derived HDMI audio signal or a coaxial input
signal is processed and provided to an external audio
amplifier via a coaxial S/PDIF digital audio connector.
The VS-226 provides a convenient way for the user to
watch a high definition television program while also
recording it in standard resolution via a DVR or VCR.
Specifications:
• Video Input: HDMI connector
• Compliant with HDMI 1.3 and HDCP 1.2
• Output: Analogue HD-15 (RGBHV / YPbPr)
• Operation frequency: up to 165MHz
•Resolution: RGBHV up to UXGA@60Hz, Component
up to 1080i (note this unit will not scale the signal,
the output resolution is determined by the resolution
of the input signal – please check your display is
compatible with the resolution produced)
Code RGB2S
59.99
£
S-video to Composite Video
Bi-directional Convertor
An amazing little gadget with an S-video socket at
one end and a composite (phono) socket at the other.
Containing a special filter network it works fully
bi-directionally. It won’t magically increase picture
resolution, but it will make life easier when wiring
up say an AV amp that supports composite or
S-video connections but doesn’t allow the use of
both simultaneously.
Code HDMIVGAP
• Automatic Signal Conversion
• HDMI 1.2, HDCP1.1 and DVI1.0 compliant
• HDMI or DVI HDTV Signals from 480p to 1080p
• Jitter corrected, Re-Clocked HDMI Bypass signal
• HDMI or DVI HDTV to NTSC or PAL Conversion
• Converts HDMI Bitstream audio to S/PDIF Audio
• Provides analog L/R Stereo Audio Output
• Converts PC signals to UXGA/60Hz to NTSC/PAL
*** Important! Please be aware that this unit will not
output composite video, s-video or stereo audio from
an HDCP protected source. A source such as a Blu-ray
or SkyHD usually uses HDCP and so only the HDMI
loop-through and digital audio ouput will be active. If
you would like any guidance with this please don’t
hesitate to contact us.
59.99
£
Code STOC
10
Features and Specifications:
9.99
£
Email your order to us at sales@keene.co.uk
Code VS226
185.56
£
RGB Conversion & Distribution
RGB SCART & S-video to HDMI 1080p HD Convertor
HD UltraBridge
This device contains a high quality chipset to convert analogue Scart AV signals (RGB or composite, or s-video and
upscale them to a choice of HDMI resolutions, 720p, 1080p, 1680x1050, 1360x768 and a choice of screen
modes (16:9, 16:10, expand & subtitle). Control is by front panel or supplied IR remote. Great for connecting
legacy equipment to an HDMI switchbox and for simplifying your connections.
A powerful multi-format HD video switcher, the UltraBridge
has:
• 1 X Component (YPbPr) video and audio inputs (480i/p,
576i/p, 720p 1080i/p (60Hz/50Hz))
• 1 X VGA video input and stereo audio input: (up to 1920
X 1200 (60Hz)
Inputs:
SCART - CVBS/y/c (PAL, NTSC), RGB (480i, 576i)
s-video PAL (576i) NTSC (480i)
• 1 X S-video video input and L/R audio input
• 1 X Composite video input and L/R audio input
HDMI Output:
• 2 X HDMI input: supports 480i/p, 576i/p, 720p/1080i
and 1080p at 50/60Hz
1920 x 1080, 1680 x 1050, 1360 x 768,
1280 x 720 with digital audio
• 1 X USB 2.0 input supports to read contents of hard disk
or flash drive and files (will read mpeg 1/2/4, rm, rmvb,
mov, jpeg, bmp, png, wma, mp3) All inputs can be
switched to 1 scaleable HDMI output at up to 1080P
Power: 5v DC 2000mA, UK adaptor supplied
Dimensions: 170 x 110 x 32mm
Code HDUSPRO
VGA to HDMI Convertor
Allows you to display the image from your computer to a
monitor or large TV. It will convert your PC’s VGA video and
audio into one complete HDMI signal.
Features:
• Converts VGA video and audio into one HDMI signal
• Signalling rates up to 1.65Gbps
• HDCP Compliant
• Supports up to 1080p resolution
• Supports 480i, 576i & 1080i resolution
• Supports VGA resolutions up to 1280 x 1024 60/75Hz
• Outputs HDMI
59.99
£
Component VGA & Audio to
VGA Convertor Switch
The Coosis HD GAMING PRO (Component to VGA 1080
Convertor, Model: HG.PRO) provides an easy way to convert
analogue component (YPbPr) signal to VGA up to
1920X1200 resolution. It enables you to carry on using
previous models of monitors, CRT projectors, digital
projector, or plasma displays which are not Component
inputs compliant. Easily connect devices such as PS3,
XBOX360, Wii, satellite boxes, or Blue-ray players etc. Being
aware of the stretched image caused by varied screen
aspect ratio (4:3, 16:9 & Full screen), this convertor is
integrated with image aspect ratio correction to recover 1:1
pixel matching. It also provides a VGA input to take the
signals from PC, laptop or other VGA sources, and mirror to
VGA output and audio output when in stand-by for easy
monitoring so you don't need to keep switching cables.
Code UBRIDGE 274.99
£
HDMI Cross Convertor
This HDMI Scaler can accept audio embedded in the
incoming HDMI signal or from the separate Toslink or
analog Stereo inputs. The HDMI output can be the same
resolution or scaled to a different resolution. Output audio
is simultaneously present embedded in the HDMI signal and
separately as Toslink and analog Stereo. This provides
maximum flexibility for systems integration. The unit is ideal
for situations where the HDMI source resolution and/or
frame rate is incompatible with the display device’s
resolution/frame rate. A comprehensive OSD menu and
buttons allows selection of output resolution, adjustments
of picture quality and audio source selection. It’s also
possible to add up to 150ms of audio delay to compensate
for lip sync errors.
Features and Specifications:
• HDMI v1.1, HDCP 1.1 Compliant
• Maximum I/O Resolutions WUXGA and 1080p
• Accepts 480i or 576i SDTV input
• Automatically Detects Input Resolution
• 50/60Hz Frame Rate Conversion
Code VGAHDMI 59.00
£
HDMI to SDI Convertor
Mini Convertor HDMI to SDI is ideal for converting from
HDMI devices to SDI video with the choice to embed SDI
audio from HDMI, AES/EBU or balanced analogue audio
inputs. Now you can add SDI outputs to cameras with
HDMI connections, or add if your computer supports HDMI
compatibility via DVI to HDMI adapters, then you can use
for adding SDI outputs to computers.
Specifications:
• HDMI to SDI Analogue Conversion
• Auto Switching SD and HD
• New 3 Gb/s SDI Technology
Code HDGPRO
69.99
£
Component and Audio input to HDMI output
This unit will take in a Component video signal plus
analogue stereo audio and
convert the output to digital HDMI.
This unit will take in HDMI and give out VGA with analogue
stereo audio.
Supported input resolutions:
4801/P, 576i/P, 720P 1080i/P
Specifications:
• Video Input: HDMI socket
Specifications:
• Video input: 3 x RCA
phono
Also available, an SDI to HDMI Convertor
Code CONVMSH
219.26
£
£219.26
HDMI in to VGA and decoded analogue audio out
HDMI 1.3 compatible
Supported Component
input resolutions:
4801/P, 576i/P, 720P 1080i/P
Code CONVMHS 196.80
£
HDMI to VGA & Audio
Convertor
Component to HDMI Convertor
HDMI 1.3 compatible
• Built in AES/EBU or Analogue Audio
Code 1TVS626 • Audio Output: 3.5mm jack
socket
• Audio input: 2 x RCA phono
• Video Output: 15pinHD
VGA connector
• Video Output: HDMI socket
• Dimensions: (WxHxD): 84 x 28 x 76mm
• Dimensions: (WxHxD): 84 x 28 x 76mm
• Power: 5V 2A (UK mains adaptor supplied)
• Power: 5V 2A (UK mains adaptor supplied)
Code CHUCH 59.99
£
Find product information and data sheets on www.keene.co.uk
Code CHUHV 59.99
£
11
HDMI Cables
Aavara High Definition HDMI Cables
These are top specification Hi-Definition AV Cables fully
supporting all of the latest HDMI specifications, including:
3D, 4K, ARC (Audio Return Channel), HEC (HDMI Ethernet
Channel). The construction features pure gold 24K plated
end shell and connector with a protective braided
cable sheath.
MINI HDMI range
Specifications:
•Works with PS3, XBOX, Blu-Ray/HD/DVD player,
Set Top Box
Cables with a standard type A HDMI plug at one end to the
mini “C” type connector (10.42mm x 2.42mm) at the other,
commonly used on camcorders and other portable AV devices.
• 1.2Gbps Ultra Wide bandwidth enable brilliant 1080p
HD content and 8 channel Audio
Specifications:
•Fully wired 19pin connectors
• Exclusively Superior Diamond cutting design and stylish
yellow webbing lines
•HDCP compliant
• HDMI to DVI interoperability allows easy interconnectivity
• Support Dolby True HD and DTS-HD Master Audio
Transmission
•High Speed rated
•Up to 1080p resolutions
• Support x.v. Colour Wide Gamut and 16bit Deep Colour
Video Transmission
Code HDAV05
Code HDAV1
Code HDAV2
Code HDAV3
0.5m version
1m version
2m version
3m version
£14.99
£17.99
£12.99
£24.99
180 Degree swivel Plug
Bend to shape HDMI cables
High quality ‘High Speed with Ethernet’ HDMI cable. Each
plug has 180 degree swivel to make it easier to connect to
awkward sockets.
From CYP, these “Neat & Tidy” cables provide genuine
innovation for the custom installer. The reinforced structure
allows them to be manipulated into a desired shape which
will be retained for the duration of an install. This new
design allows installers the make tidiest of finishing touches
to an AV installation, while also optimising the connection
between sources in a rack.
NEW
Specifications:
•
Full 1080p and deep
colour resolutions
Code HDHD141S
Code HDHD142S
Code HDHD143S
1m version
2m version
3m version
Code HDHDM3
£9.99
£12.99
length 3.0m
HDMI mini plug to HDMI mini plug
Code HDMHDM2 length 2.0m
Code HDMHDM3
£9.99
£12.99
length 3.0m
MICRO HDMI range
Cables with a standard type A HDMI plug at one end to the
micro type “D” connector (6.4mm x 2.8mm) at the other,
commonly used on mobile phones.
NEW
• 3D Compatible
Specifications:
•Gold plated terminals with moulded strain relief
HDMI plug to HDMI mini plug
Code HDHDM2
length 2.0m
• 99.999% Oxygen Free Copper
£14.99
£19.99
£24.99
Code HDMI030
Code HDMI050
Code HDMI075
30cm version
50cm version
75cm version
£10.67
£11.45
£12.43
Aavara Hi-Definition Pro Install HDMI Cables
These are top specification Hi-Definition AV Cables designed
for Professional and Commercial installations. Designed to
end the uncertainty and erratic behaviour you may have
experienced from some of the other longer length cables on
the market, these deliver reliable results. The construction
features a heavy duty metal-moulded connector housing
with high density triple layer shielding to guard against
electromagnetic interference, high-level OFC copper wire
with 340MHz (10.2Gps) ultra-wide bandwidth for 1080p
3D video format and 7.1 channel audio. Protective braided
outer cable sheath.
Code HDHDMIC1
•24K Gold-plated connector
for anti-corrosive and
distortion-free
HDMI CABLES
High Speed with Ethernet
Code HDHDMIC15 length 1.5m
Code HDHDMIC2
length 2.0m
Cables with High Speed 1080p support plus ethernet
capability.
Code HDPROAV5
5m
Code HDPROAV10 10m
Code HDPROAV15 15m
Code HDPROAV20 20m
£29.99
£59.99
£89.99
£119.99
Code HDHD1405
Code HDHD141
Professional Range Flat Profile
Ultra Slim HDMI Cables
Flat cable manufactured by TTL offering high speed
performance 1440P with Ethernet and Audio return
channel. Manufactured with gold plated contact and shell
including RF Blok which protects against RF interference.
Lightweight flat ribbon cable which is very flexible for
installation especially where there is limited space.
At last, an HDMI cable that doesn’t feel like it’s trying to
escape from the socket you’ve just plugged it into! These
Ultra Slim cables cram everything you need for the full HD
experience into a very slim flexible cable.
Specifications:
•Capable of handling
up to 1440p resolutions
£9.99
£11.99
£13.99
length 1.0m
Specifications:
•HDMI™ 1.4v high speed Cable supporting 3D, 4K, ARC
(Audio Return Channel)
Code HDHD1418
Features:
• HDMI V1.4 compliant
Code HDHD143
Code HDHD145 Code HDHD1410 £3.99
£4.99
£11.99
£14.99
£17.99
£34.99
length 0.5m
length 1m
length 1.8m
length 3.0m
length 5.0m
length 10.0m
HDMI Adaptors
• Audio return Channel
• 3D support
•3D compatable
•4K x 2K ready
• 4K x 2K resolution
•High quality flat cable
ideal for running under
carpet or through
narrow spaces
• Deep colour support
•
Ethernet up to
100Mbps
•
36AWG ultra thin flex cable with gold plated connectors
Code HDHDF1405
length 0.5m
Code HDHDF1415 length 1.5m
Code HDHDF1420 length 2.0m
Code HDHDF1430
12
length 3.0m
£10.80
£12.96
£15.14
£17.36
Code KA191 (270 degree rotation)
£7.99
£7.99
Code KA191F (90 degree flat)
£6.99
£6.99
Code KA191L (90 degree rotation)
Code HDUS05
Code HDUS1 Code HDUS3
length 0.5m
length 1.0m
length 3.0m
£9.99
£11.99
£16.99
Email your order to us at sales@keene.co.uk
Code KA213 (270 degree flat)
CAT5 & Networking Cabling
UTP CAT5E Cable
Coosis Python HDMI Cables
HDMI Outlet Plates
The Coosis Python series of HDMI cables are ultimate
High-Speed with Ethernet cables (Cat 2) for HD signal
transmission. Upto 15.8G bandwidth permits a lossless
transmision of uncompressed 4K × 2K high definition
pictures with maximum 48bit/px colour depth. It also
integrates an HDMI Ethernet Channel (HEC), which
allows for a 100 Mbit/s Ethernet connection between
the two HDMI connected devices so they can share an
Internet connection. Additional Audio Return Channel
enables a TV, via a single HDMI cable, to send audio
data “upstream” to an A/V receiver or surround sound
system, increasing user flexibility and eliminating the
need for any separate S/PDIF audio connection. Each
cable is also supplied complete with an HDMI plug to
socket 180 degree swivel adaptor, allowing it to be
used even in very tight spaces.
From Keene, a wall plate with an HDMI socket at the front
and a PCB mounted rear socket. The rear socket is aligned
such that a side entry HDMI cable should pass through one
of the side knock-outs in a std metal rear pattress.
Depending on the size of plug used some modification to
the pattress may be necessary.
We can supply this item as follows:
Code HCP26
Code HCP26SD
Code HCP26FS
PRG4
PRG8
PRG16
PRG25
PRG35
PRG40
PRG50
PRS4
PRS8
PRS16
PRS25
PRS35
PRS40
PRS50
FLAT GOLD 2.44M
FLAT GOLD 4.88M
FLAT GOLD 7.62M
FLAT GOLD 10.67M
FLAT GOLD 12.2M
FLAT GOLD 15.2M
FLAT SILVER 1.22M
FLAT SILVER 2.44M
FLAT SILVER 4.88M
FLAT SILVER 7.62M
FLAT SILVER 10.67
FLAT SILVER 12.2M
FLAT SILVER 15.2M
ROUND GOLD 1.22M
ROUND GOLD 2.44M
ROUND GOLD 4.88M
ROUND GOLD 7.62M
ROUND GOLD 10.67M
ROUND GOLD 12.2M
ROUND GOLD 15.2M
ROUND SILVER 1.22M
ROUND SILVER 2.44M
ROUND SILVER 4.88M
ROUND SILVER 7.62M
ROUND SILVER 10.67M
ROUND SILVER 12.2M
ROUND SILVER 15.2M
£19.99
£29.99
£39.99
£54.99
single, white
double, white
single, steel
double, steel
Single gang flat brushed steel
FLAT GOLD 1.22M
£39.99
£19.99
£23.99
£40.99
£51.99
£58.99
£70.99
£79.99
£19.99
£23.99
£40.99
£51.99
£58.99
£70.99
£79.99
A wall outlet plate with a HDMI socket at the
front and an angled HDMI socket at the rear. A
deep (47mm) back box is recommended.
Depending on the size of the plug on the
HDMi cable used, some modification to the
pattress may be necessary.
£18.99
£22.99
£38.99
£48.99
£56.99
£67.99
£76.99
£18.99
£22.99
£38.99
£48.99
£56.99
£67.99
£76.99
Code HCP26FC
Code HCP26G
UTP CAT6 Cable
Unshielded 4 pair twisted cable. 24AWG non-plenum
horizontal (solid conductor). Flame retardent grey sheath
with rip cord (305m pack only). Order code [KBL33] loose
by the metre or 305m pack in easy-pull box.
Couplers & Connectors
CAT5E coupler, back to back RJ45 sockets.
Code C5EC
Code C5EC
buy 5
Code C5EC
RJ45 clear plastic crimp-on end connector, suitable for
KBL23xx cable.
Code CAT6C
crimp on connector CAT6
rated for KBL33
Code HDDV10 length 5.0m
length 10.0m
CAT5 Outlet Components
Code KA189
RJ45 fascia plate for network
connections containing IDC
connections for UTP cable
(suitable cable KBL23/KBL33).
A clip-in ID plate allows for
easy labelling.
£6.99
HDMI adaptor type A socket to
type C mini plug
Code KA190
£7.99
Single port version
Code UTPSP
Code UTPTP
Code NPB
Code KA173H
£14.99
Code UTP20
length 3.0m
length 5.0m
Code HDHDE10 length 10.0m
£2.99
Professional HDMI socket coupler in
Black D shaped XLR cutout, ideal for use
in patch panels as well as wall and floor
plates. (Silver finish)
Code KLC123
£1.99
• Colour: Grey
• Connectors: 2 x RJ45
•A
pplications: 10BaseT,
100BaseTX & Gigabit Ethernet
• Crossed connections = NO
£6.99
Code UTP10
Code HDHDE5 £7.99
Product description
Code UTP05
Code HDHDE3
£5.99
CAT5E/6 Patch Leads
Back to back coupler for joining
HDMI cables.
Code KA173
£9.99
£11.99
£14.99
£24.99
£9.99
Surface mount pattress box 25mm deep for use with CAT5
fascia plates
HDMI hinged 90 degree coupler
length 2.0m
£0.99
Pattress box 45mm deep has breakouts for cable entry on
four sides and bottom
HDMI plug to HDMI socket extension cable High Speed.
Code HDHDE2
Twin port version (pictured)
£19.99
HDMI socket to socket coupler
HDMI Extension Cables
Code RJ45T
Code UTPP
Code HDDV5 £0.49
(CAT5)
Code RJ45C
RJ45 crimp tool for easy
fixing of RJ45 end connectors.
Display port male to female HDMI
£7.99
£12.99
£14.99
£19.99
£1.99
£7.50
£12.50
buy 10
HDMI adaptor type C mini socket to
type A plug
Code MDPHDMI
length 3.0m
305m reel
£9.99
HDMI plug to DVI plug
1080p rated.
length 2.0m
10+m
DVI Plug to HDMI socket Adaptor
Code KA170
£0.78/m
£0.68/m
£173.85 (0.57/m)
1-10m
Code KBL33
£29.99
HDMI to DVI Cables
Code HDDV3 305m reel
Code KBL33
A wall plate with a HDMI socket at the
front and a HDMI socket at the rear,
connected via a short (10cm) flexible cable.
Ideal for situations where the rear HDMI
cable is drawn through from unusual
angles. Depending on the size of plug used
some modification to the pattress may be necessary.
white
Code KBL33
£19.99
Mini Display Port to HDMI adaptor
cable 15cm
Code HDDV2
10+m
Code HCP26D
£0.49/m
£0.40/m
£109.80 (0.36/m)
1-10m
Code KBL23
Code HCP26S
PFG4
PFG8
PFG16
PFG25
PFG35
PFG40
PFG50
PFS4
PFS8
PFS16
PFS25
PFS35
PFS40
PFS50
Unshielded 4 pair twisted cable.
24AWG non-plenum horizontal
(solid conductor). Beige sheath
metre marked, with rip cord
(305m pack only). ANSI/EIA/TIA568-A-5, ISO/IEC-11801/BS EN
50173, UL444, UL1581, UL
1666 approved. Order loose by
the metre or by the 305m pack.
Code UTP30
(L) 0.5m grey
(L) 1.0m grey
(L) 2.0m grey
(L) 3.0m grey
Code UTP50 (L) 5.0m grey
Code UTP100 (L) 10.0m grey
£9.99
Code UTP200 (L) 20.0m grey
Code UTP300 (L) 30.0m grey
Find product information and data sheets on www.keene.co.uk
£1.49
£1.49
£1.99
£3.99
£4.99
£8.49
£10.99
£19.99
13
HDMI Switchboxes
CONNECT 420 5:1 HDMI Switch 3D AAVARA 4:1 Switchbox
•Only one cable to your TV screen! Switch between the
HDMI devices connected
•Suitable for connecting 5 HDMI sources to your TV
simultaneously. You just need 1 HDMI input and you
never have to switch cables again
•Suitable for Full HD 1080p and all 3D formats
•With built-in repeater and equalizer for correcting any
possible loss of signal, so you can connect up to 15
metres of HDMI cable to the output
The Aavara SW421 provides easy switching from any of four
HDMI inputs to 1 HDMI output. Featuring CEC (Consumer
Electronic Control) Pass-through for fast switching this is a
very effective and economical solution.
Features:
• Allows access from four HDMI devices to 1 HDMI display
• CEC (Consumer Electronic Control) pass-thru (Output
Channel 1)
•Switches automatically and/or with remote control
• Support 36-bit Deep Color up to 1080p
•Solid metal casing
• Support x.v.YCC wide color gamut
Features:
• No need to make space for another piece of hardware
• Fully HDCP Compliant
• Support 7.1 digital surround & Lip Sync
81.00
The smallest HDMI auto selector on the market! This is a
very neat switchbox, two inputs to one output. They’re
line powered so you don’t need to find room for another
mains adaptor and they automatically switch to whichever
input device was switched on last (with a manual override
should you wish). Brilliant, neat, tidy and very affordable just fit it and forget it!
•Integrated high quality 0.5m HDMI Cable removes need
to purchase additional cable
• Audio support Dolby TrueHD & DTS-HD™
Code C420
HDMI Automatic 2:1
Line Powered Switchboxes
• HDMI firmware upgradable
• Automatically switches to equipment source when
switched on
• Plug-and-play. Installs in seconds
• Manual override switch
• Dimension:245(W) x 107(D) x 27(H) mm
• Self powered. No additional PSU required!
• Package Content:1080p HDMI Switcher 4:1, Remote
Control, 9V DC Adapter, Usermanual
• With plastic end connectors and regular shielded cable
£
CONNECT 310 3:1 HDMI
Switch 3D
•Only one cable to your TV screen! Switch between the
HDMI devices connected
•Suitable for connecting 3 HDMI sources to your TV
simultaneously.
You just need 1 HDMI input and you never have to
switch cables again
Code SW421
•For connecting a game console like PlayStation and
Xbox,
Blu-ray Player, satellite receiver and all other HDMI
devices
• Full HD 1080p
• Switches automatically and/or with remote control
• With separate IR receiver for operating the switcher
when it is placed out of sight
49.99
£
HDMI 3:1 3 in 1 Out
Micro Switchbox
The HDMI Amplifier Switch Splitter is an HDMI splitter with
the ability to switch between 3 inputs to display to 2
outputs. It distributes the input into the two identical
outputs simultaneously. Each output can achieve a long
distance transmission of a HDMI signal of up to 15 metres.
Two or more products may be cascaded to achieve a larger
distribution and longer length. Operation is by front push
button control or by (supplied) IR remote.
This is a really tiny yet fully functional 3 to 1 HDMI
Switchbox. It will switch between 3 HDMI sources
(in multiple resolutions up to 1080p) and route the signal to
an HDMI output. The unit will switch automatically to the
device turned on, and can also be manually switched via the
push button. An LED indicates which input is selected.
The case dimensions are just 52 x 52 x 18mm!
• Support HDMI1.3b
29.95
HDMI Switchboxes Value Range
Compact low cost HDMI switchboxes offering excellent
value for money. Auto source selection (plus IR for SW103).
Features:
• Supports 12-bit deep colour, full 1080p
• Intelligent or manual switching
• Supports HDMI v1.3b
• High performance up to 2.5Gbps
• Support highest video resolution 1080p
£
29.99
£
HDMI 3:2 Switcher Splitter
Value Range
Features:
•Switch easily between any three HDMI sources to
two displays
Code C310
Code 28577H • Support 225MHz/2.25Gbps per channel
(7.5Gbps all channel) bandwidth
•Maintains high resolution video HDTV up to 1080p 2k,
1440p graphics and computer resolutions up to
1920 x 1200
• Support 12bit per channel (36bit all channel)
deep colour
• No power needed
• Support HDCP
Note - Devices with DVI output are not supported due to
the lack of signal control.
Features:
• Easily switch between HDMI sources
•Full HD 1080p supported
•Compatible with HDMI 1.3b and HDCP
Note – not suitable for DVI devices
(no control signal for auto switching)
Code HDMI32S 49.99
£
Code HDMIM3
18.99
£
HDMI four way auto switch
Code SW102
Code SW103
(two inputs to one output)
(three inputs to one output)
£24.99
£29.99
The HD-SW104 is an intelligent HDMI amplified 4 port
switch. It allows four HDMI devices to be switched to one
HD Monitor, Projector or HD TV.
Specifications:
• 4 Port HDMI Switch
The intelligent function will automatically switch between
HDMI sources as and when they are plugged in, removed
or turned off, plus there is also touch button and IR
remote control.
• Supports up to 1080p
• HDMI v1.3b
• Supports 250Mhz/2.5Gbps per channel bandwidth
• Supports 12-bit per channel deep colour
• Supports HDCP pass through
Code SW104 14
Email your order to us at sales@keene.co.uk
39.99
£
HDMI Matrix Switchers
4X1 COMPOSITE OR S-VIDEO &
AUDIO SWITCH
Aavara PM4X2 1080p HDMI
1.3b MATRIX 4X2
MX-3141 series 4x1 Routing Switchers are extremely
wide bandwidth, high performance products that meet
the most demanding requirements for signal routing.
Video as well as Audio are routed. Video Bandwidth is
flat +/- 3db to beyond 300MHz ensuring these
switchers will provide an output identical to the source
signals.
The Aavara PM4X2 1080p HDMI 1.3b MATRIX 4X2 is a
switcher/splitter hub that offers you maximum convenience
in HDMI signal distribution when you have multiple HDMI
sources and displays to connect together. Each of the Four
HDMI sources can be directed to any one of the two HDMI
outputs so two displays/projector can show same source or
two different sources simultaneously. It is compliant with
Blu-ray DVD players and satellite set top boxes to any HDMI
compatible display. Sources are accessible at any time to
any display when operating with the IR remote. PM4X2
4x2 matrix switching allows maximum versatility for
integrated systems.
The MX3141CSVA switches NTSC or PAL Composite or
S-Video plus Stereo Analog Audio. This unit features
RS-232 control capability and is shipped with an IR
remote control, a rack mount kit plus an AC power
adapter
Features and Specifications:
• Professional Grade, High Performance Switcher
• Video Bandwidth: Greater than 300MHz
• NTSC and PAL Television Standards
• Inputs: 4x composite video on RCA, S-Video on mini
4 pin din and Stereo Audio on RCA
• Output: 1 x composite video on RCA, S-Video on
mini 4 pin din and Stereo Audio on RCA
• Push Button and IR Inputs Selection
• Rugged Metal Case
• Locking DC Power Connector for Security
Features:
• Allows you to select same HDMI source or two different
sources output to two displays separately
Specifications:
• HDCP Spec.:1.3b Compliant
• DVI Spec.:1.0 Compliant
• HDCP Spec.:1.2 Compliant
• MATRIX 4X2:Transmit same source or two different
sources simultaneously
• Operation temperature:+5ºC to +35ºC
• Storage temperature:-20ºC to +60ºC
• Humidity Range:5% to90% RH
• Signal Rate:6.75Gbps
• Power Consumption:5W
• Video Bandwidth:225 MHz
• Single Link Range:Supports 480i, 480p, 576i, 576p,
720p, 1080i and 1080p resolution
• Cable Length:5M (In and Out respectively)
• Dimension:245(W) x 107(D) x 27(H) mm
• “Max. Video Output” function for Home Theater
installation, allow to send to TV and Amp with Max.
Video and Audio signal
• HDMI Specification 1.3b Compliant
• Support HDMI 36-bit Deep Color & x.v.Color wide
color gamut
• Supports 480i, 480p, 576i, 576p, 720p, 1080i and
1080p resolution
• Audio support Dolby® TrueHD & DTS-HD™ lossless 7.1
digital surround & Lip Sync
• Plug-and-play. Installs in seconds
• Easy operating with IR Remote
HDMI Matrix Switchers
Value Range
These are true HDMI Matrix switchbox that routes any of
the four HDMI inputs to any or all of the outputs. Input
routing by front panel push button or IR remote control
with LED confirmation. Matrix switching allows for
maximum versatility for integrated systems.
Superb value for money.
92.40
Features:
• Switch easily between any four HDMI sources
• Distributes any of the four inputs to any or any
combination of the two HDMI output displays
• Support HDMI 1.3b
• Support highest video resolution 1080p.
• Support 225MHz/2.25Gbps per channel
(6.75Gbps all channel) bandwidth
• Support HDCP
• External 5V DC@2A Power Supply (included)
AAVARA PS124 HDMI 1080p
Splitter 1 to 4
• Easy operating with IR Remote
*** Note - Devices with DVI output are not supported due
to the lack of signal control ***
The Aavara PS124 is an HDMI v1.3b 1080p distribution hub
that sends the same HDMI video output to four HDMI HDTV
digital screens. It is a flexible solution to integrate multiple
displays in signage, video wall or demo shelf.
Four inputs to two outputs
Code HD42M
Code HD44M
•CEC (Consumer Electronic Control) pass-thru (Output
Channel 1)
•Support 36-bit Deep Color up to 1080p
£299.99
BeOne Media Panel
New from Coosis, a stylish Multimedia AV Wallplate ideal
for Hotels, Apartments, Meeting rooms etc.
The LAN/RJ45 and PHONE/RJ11 two inputs are pass-through.
Cut-out size 376 x 78mm x 76mm deep.
There are front inputs for Composite & Audio, S-video,
HDMI, VGA & 3.5mm stereo audio, and these are all
automatically converted to a single HDMI output. The input
is automatically switched to an active signal and will
automatically revert back to the previous when the current
becomes inactive. Touch sensitive switches in the backlit
panel can be used to override the auto input switching if
required.
•Audio support Dolby® TrueHD & DTS-HD™
•Support 7.1 digital surround & Lip Sync
•Plug-and-play. Installs in seconds
Specification:
•HDMI Spec:1.3b Compliant
•DVI Spec.:1.0 Compliant
• HDCP Spec.:1.2 Compliant
• CEC:Allows 1 TV remote to sync interoperability between
display/projector and HDMI AV devices connected
• Dimension:245(W) x 107(D) x 27(H) mm
NEW
There is a USB port which can operate in one of two modes;
it can be set to work as a charge output (5v 1A) or it can be
routed through to the display USB if this supports media
playback.
Code BEONE Code PS124 £84.99
Four inputs to Four outputs
Features:
•Distribute HDMI signal to 4 HDMI displays
•Daisy Chain up to 3 layers /256 displays (4 x 8 x 8)
193.37
£
• Support 12bit per channel (36bit all channel) deep colour
£
Code MX3141CSVA
Code PM4X2 299.00
£
119.00
£
Find product information and data sheets on www.keene.co.uk
15
HDMI Over Long Distances
HDMI over IP Network
HDMI Analyser
As well as HDMI over (dedicated) Cat5 cable we can now
offer transmitter / receiver systems that will send HDMI
signals via an IP computer network. Amazingly they place
very little load on your network bandwidth and operate as a
true multicast - that is to say one transmitter can drive
multiple receivers with no extra network load! They really
are extremely simple to operate, just plug and play with no
in-depth networking capability required. They also provide
full IR feedback allowing remote control of source
equipment. A flexible, scalable, low cost solution to
distributing HD signals to multiple displays. They can be
used in Extender Mode (connect the Sender to the Receiver
by CAT5e/6/7 cable directly) or Broadcaster
Mode (Sender to Receiver via LAN) for one Sender to
many Receivers.
PB5000P
The XA-1 is the perfect analysis tool for AV installers and
integrators. This device allows the user to analyse AV
sources for resolution and EDID information whilst also
providing pattern generation and test functions for
identifying display capabilities. This small but advanced
HDMI analyser also supports the analysis and pattern
generation of 3D signals. This allows the user to check
compatibility between sources and displays and provides a
means of identifying system problems for troubleshooting.
Features:
• Supports v1.4 HDMI Audio Return Channel
(ARC) function
•Support timings include SD, HD up to 1080p, PC up to
WUXGA and 3D
• Analyse input source info-frame and output sink EDID
• Deep color video support up to 12-bits
• HD resolutions supported - 480i to 1080p + 1080p24fps
• PC resolutions supported - VGA to SXGA + WUXGA
The newly updated PB5000Plus units now provide IR feedback and RS232 control
• 3D modes supported - Frame Packing (720p@50/60,
1080p@24); Side-by-Side (half)(1080p@24/60,
720p@50/60); Top-and-Bottom (1080p@24/60,
720p@50/60)
and deliver stunning Ultra High Quality 1080p HDMI Video broadcast over IP network.
Via an inexpensive Gigabit Ethernet network switch the PB5000P can support Point to Point, Point to
Many Broadcasting, and Multi-Casting which multiple video sources with PB5000+ Senders video streaming to multiple TVs/
Displays/Projectors with PB5000+ Receiver. Multi-casting can be done by Managed Gigabit Switch with 802.1Q VLAN
function which provide control remotely and allows more video source/senders to be integrated.
PB5000P
Features:
• 1080p Ultra High Quality Video transmission and up to
16 Groups Multi-Casting
• IR Pass-Thru on 1 to 1 extender configuration
• Up to 16 Groups Multi-Casting
• IR Control Pass Thru
•Two Way RS-232 Command Unicast Broadcast for
control from remote site
•Easy Dip Switch Matching for Multi-Casting
Group configuration
•New EDID Copy/Video Mode Switching Button for
Optimal Video Performance
•Video Wall function support for up to 8x16 displays
by Easy Web Interface Configuration
•Optional PoE support upon request
• Flexible and scalable HDMI 1080p broadcasting with
Gigabit Ethernet LAN
• 1 to 1, 1 to many & multi-casting broadcasting
architecture, adding more displays without adding
LAN bandwidth loading
• Multi-Casting group with Gigabit Ethernet managed
switch (required 802.11Q VLAN & IGMP function)
support, up to 16 multi-casting group support
• 16 sets C class IP Dip switch configuration on both Sender
& Receiver for easy Multi-Casting group matching
Specifications:
• Video Resolution:480i/p, 576i/p, 720p, 1080i/p
• Sender Connector:Power Adapter in, RJ45,
RS232, IR Emitter Connector, HDMI
• Receiver Connector:Power Adapter in, RJ45,
RS232, IR Receiver Connector, HDMI out
• HDMI Spec.:1.3 Compatible
• DVI Spec.:1.0 Compliant
• HDCP Spec.:1.2 Compliant
• Link Connector:RJ45
• Power Consumption:3.2W
• Audio System:Stereo L/R
• Audio Resolution:16bit 48Khz
• max CAT5 Cable Length:100M
• Power Adapter:DC 5V/2A
• Provides 25 timings and 6 patterns
• OLED show Input / Output timing information
• Support input signal bypass, digital video formats in
Deep Color Mode at up to 36 bits (12bits/color) and new
lossless compressed (Dolby TrueHD, Dolby Digital Plus
and DTS-HD master Audio)
digital audio
• Supports internal
pattern audio LPCM 2CH
48/96/192KHz, LPCM5.1
48/96 kHz, LPCM7.1
48/96KHz
Code XA1 306.44
£
HDMI over CAT5E/5 Extender
One of the Professional series of HDMI Cat5 3D Extenders.
The PE121L features 3D, IR and HDMI Ethernet Channel
Pass-Thru, all via twin CAT5E cable. Fully compatible with
Blu-Ray 3D and featuring IR pass-through this is a great
problem solver and it’s compact size makes it very
unobtrusive.
Features:
• Uncompressed 1080p HDMI over Cat5e/6/7
PB5000P
• Local HDMI output on Sender unit
• Full range IR Pass-Thru (receiver & emitter included)
• CEC Pass-thru allows one remote control to sync TV and
AV devices
Code PB5000P
Code PB5000PR
Sender/Receiver pair
Additional receiver
£524.54
£394.62
• Support HDMI v1.4 3D video format Blu-Ray player
and 3D TV
• Support v1.4 HDMI Ethernet Channel
Specifications:
• HDMI Spec: v1.4 Compliant
HDMI over Single Coaxial Extender
Yet another really useful way to get HDMI from one place
to another, the PCE122 can send ultra high quality HDMI
v1.3 over a single coaxial cable! (RG6 or RG59). It can
send full HD 1080P up to 120M or 720P up to 230M,
both with full 7.1 channel audio. The conversion is fully
digital (HDMI to SDI and back again) with no additional
compression and gives you crystal clear HD at long
distances. The PCE122 also contains a built-in 1 to 2
Coaxial Splitter to drive two separate receivers and each
receiver has a loop-through
to daisy chain
additional receivers as
required. Cables are
connected via BNC for
a secure, vibration
resistant connection.
Specifications:
• 120M HDMI 1080p video and 7.1channel audio one
cable transmission with Ultra High Quality Video
• Features World Leading Single Coaxial Transmission,
designed to simplify Installation
• 1080p 120M / 720p 230M long distance Ultra
High Quality Video with 7.1 channels surround
sound transmission
• Up to 7.1 channels audio, Dolby® Digital / Dolby®
TruHD/DTS®-HD pass-thru
• DVI Spec: v1.0 Compliant
• HDCP Spec: v1.2 Compliant
• Video Format: Up to 1080p 3D Uncompressed Video
• Audio Format: Up to 7.1 Channel, DTS HD Master Audio/
Dolby TrueHD
• HDMI Source Input Port: 1 Port
• HDMI Display Output Port: 1 Port
• LINK Connector: RJ-45 Shielded x2
• HDMI Ethernet Channel: Pass-Thru Supported
• Built-in 1 to 2 Coaxial Splitter in Sender and One
Coaxial Cascade output in Receiver for great extension
flexibility
• Support 5 layers Cascadable for up to 600M 1080p
video transmission and up to 10 TVs/Displays/
Projectors connected
• BNC connector designed for solid coaxial connection
• HDMI v1.3b, HDCP Compliant
PCE122 with IR feedback:
Code PCE122IR
(transmitter & receiver pair with IR) £542.61
Code PCE122RIR (additional receiver with IR)
16
•­Hassle free plug-n-play, install in seconds
£315.70
Email your order to us at sales@keene.co.uk
Code PE121L 154.99
£
HDMI Over Long Distances
HDMI over CAT5
These products make a very affordable method of sending
HDMI over long distances whilst preserving the full HD
capability. The transmitter converts the HDMI signal into a
balanced differential signal and the receiver converts it back
into a conventional HDMI signal again. It uses two runs of
CAT5E (or CAT6) cable and allows for full auto-adjustment of
feedback and equalisation with no user-intervention required.
Long HDMI cables are expensive and unwieldy, whereas
CAT5E cable is cheap and flexible making it much more
suitable for long distance runs. The HDMIC50 can send HDMI
at full 1080p up to 50m (up to 100m at 480p!) They can also
be used for DVI-D signals with a suitable adaptor such as the
KA169. The HDMIC530 is rated at 1080p at 30m and 480p
at 60m.
Code HDMIC530
Code HDMIC550
£39.99
£59.99
HDMI extender over CAT5
with IR control
Specifications:
• Input Video Signal: 0.5 -1.0 volts p-p
This product makes a very affordable method of sending
HDMI over long distances whilst preserving the full HD
capability. The transmitter converts the HDMI signal into a
balanced differential signal and the receiver converts it back
into a conventional HDMI signal again. It uses two runs of
CAT5E (or CAT6) cable and allows for full auto-adjustment
of feedback and equalisation with no user-intervention
required. This model also provides IR feedback along the
same CAT5 cables for control of source equipment from the
viewing area.
• Input DDC Signal: 5 volts p-p (TTL)
• Maximum Single Link Range:
1920X1200, 1080P
• Output Video: HDMI 1.3
• Video format supported:
DTV/HDTV 1080P/1080i/720P/
576P/480P/576i/480i
• Size: 45 x 25 x 81mm
• Power Consumption: 5W (max.)
• Operating Temperature: 0 to +70 C
• External Power Supply: 5V DC@2A
Long HDMI cables are expensive and unwieldy, whereas
CAT5E cable is cheap and flexible making it much more
suitable for long distance runs. This pair of units can send
HDMI at full 1080p up to 50m and can also be used for
DVI-D signals with a suitable adaptor such as the KA169
• HDMI V1.3 compliant
HDMI over Single CAT5
50M System. Some HDMI over CAT5 transmitters require two runs of CAT5 cable. This new item can do the same job with
a single run of CAT5 cable, great for adapting existing installations. The modules are plug and play with full autoadjustment of feedback and equalisation and no user-intervention required.
Specifications:
• Input Video Signal 0.5 -1.0 volts p-p • Video Amplifier Bandwidth 1.65Gpbs/165MHz
• Output Video HDMI 1.2a
• Vertical Frequency Range 50/60Hz
• Video format supported
• Resolutions(HDTV)
• DTV/HDTV 480i/576i/480p/576p/
720p/1080i/1080P
• Interlaced(50&60Hz) 480i,576i,1080i
• Transmission distance
• CAT-6 cable 50M for1080p
• Operating Frequency
• Watch films, look at photographs and listen to music
from, for example, your Media Centre PC, Blu-Ray player,
game console, set top box or hard-disk recorder on a
different TV/projection screen in perfect HD quality
• Operate your connected A/V equipment remotely via the
infrared return signal
• Progressive(50&60Hz) 480p,576p,720p,1080p
Please note, in order to achieve the quoted
transmission distances please use only
CAT-5e or CAT-6 cable.
Code HDEX344 99.00
£
• Wired signal transmission up to 100 metres!
• Optimum price/quality ratio as a result of using CAT5e/
CAT6 cabling
• Retention of Full HD 1080p image and sound quality for
up to 60 metres
HDMI Signal Repeater 1080p Value Range
Use one of these to join two HDMI cables and extend the
maximum cable distance. The repeater contains circuitry to
regenerate the HDMI signal and extend the effective cable
length while maintaining
all signal components
present within the
encoded signal, including
stereo or 5.1 audio and
HDCP encryption. Multiple
devices can also be daisy
chained as required up to
any cable length.
Features:
• Watch and operate your HD Content elsewhere on
your TV
• Free from interruption due to solid metal, interference
free housing
Specifications:
• Extends high definition video and digital audio using a
single box solution
• Up to 30m Max cable length, also cascadable
• HDMI Amplifier Bandwith: 1.65GHz
• Dimensions 5 x 2.8 x 1.8cm
• HDMI V1.3 compliant
• Power: DC 5v 170mA max (In most cases, the repeater
is able to use the power from the appliance, and no
external power adaptor is required)
Code HDMIRV 14.99
£
Code MEG61 82.10
£
Gigavideo 821 Wireless HDMI Sender
At last, a cable free solution for HDMI. The transmitter
has two HDMI inputs and includes a local HDMI passthrough output so you can still view the sources locally.
Switch between any of the two inputs and watch the
output cable free at a distance of up to 30m (clear line
of sight, or typically 15m through walls). The signal is
uncompressed so the output will stay as true HD up to
and including 1080p. Naturally there’s built in IR
feedback so you can control the source from the
viewing area.
Features:
• Replace your HDMI cable wirelessly and locate your
HDTV or projector wherever you want
• Mount the receiver (out of sight) behind your HDTV
or on the ceiling next to your projector. No more
visible cables
• Watch up to 2 (HD) devices such as Blu-ray®
players, digital video recorders (DVRs), HD set-top
boxes, PS3™ or Xbox® game consoles or standard
DVD players/ recorders elsewhere in your home
and easily switch between the sources connected
without changing plugs
• The built-in HDMI splitter means that you can also
connect an HDTV to the Transmitter so that you can
continue to watch the connected devices locally
• Operate your A/V sources from anywhere, even
through a wall or cupboard door, using the IR
receiver
• The HD signal does not experience any delays and is
therefore perfect for game consoles
• Digitally supports all 480p, 720p, 1080i and 1080p
(Full HD) resolutions from up to 30 metres
• 100% HDCP compliant
Sends the HD signal uncompressed.
*Please note that although this wireless kit is capable
of transmitting a full HD signal through walls and
ceilings it does greatly reduce the tranmission distance.
As a general rule a ‘clear line of sight’ transmission is
easily achieved up to 20 metres, but this can be
effected by local sources of interference from mains
points, wireless routers etc. (although a little time repositioning the transmitter and receiver units can
usually get around the problem). For transmissions
where the signal is passing through a wall or ceiling,
please be mindful of the make-up of the wall or
ceiling. Naturally a signal will pass much easier
through plaster board and dry-walling than it will a
steel-reinforced concrete structure or stone walls, and
this will effect the signals transmission greatly. It is also
worth noting that if you wish to send a signal through
more than one wall or ceiling the transmission distance
will be reduced further still and careful consideration
needs to be given to where the units will by
positioned. If you would like any information or advice
to assist you please don’t hesitate to get in touch and
we will do our best to help.
We can also offer a solution with a shorter
transmission range ideal for ‘same room’ applications
GV811.
GV821
NEW
LOW PRICE
GV811
Code GV821
£265.00
Also available - GV811. A compact model for in-room use
in-room (10m range with clear line of sight). Single HDMI
input & without IR feedback. See www.keene.co.uk for
full specification.
Code GV811
Find product information and data sheets on www.keene.co.uk
£249.99
17
HDMI Over Long Distances
HDBaseT HDMI extender System
This is quite a product! The Aavara PE3D4K100A is a
another fantastic tool for installers. Using just a single wire
it can be easily retrofitted within an existing network.
HDBaseT technology allows this system to send HDMI
further and at higher quality than all other conventional
HDMI over CAT5 solutions. With no compression and no
loss of quality you can get crystal clear 3D 1080P with
7.1channel audio, and also have IR control, RS232 and
extend your 100Mbps LAN all over the one cable!
Features:
• Transmit up to 100M Uncompress 1080p HDMI signal
via CAT5e/6/7 Cables
HDBaseT HDMI
Distribution Systems
• 10.2Gbps Ulrat High Performance Transmission
support up to 4Kx2K Resolution
New from CYP, a range of HDMI HDBaseT distribution
amplifiers. Each model will take one HDMI input and send it
uncompressed to two, three or even seven outputs. If you
don’t need the flexibility (and cost) of a full matrix system
but want all the advantages that HDBaseT has to offer then
these are perfect for both residential and commercial
AV installations.
• HDMI V1.4 3D Video Format Support for 3D blu-ray
and TV connection at distance
• 36 bit Deep Color & CEC Pass Thru support
• POC (Power Over CAT5) support, Receiver no Power
Adapter needed
PU1H2HBTE
• Ethernet Extend support, 3 x 100Mbps Ethernet RJ-45
switch at both Sender & Receiver
• Full range 20~60Khz IR Pass-Thru allows to control
Video Source from receiver side
• Two Way RS-232 Control communication for Display
or video Source control at remote site
PU1H3HBTL
• Hassle free plug-n-play, install in sec
Over one single run of CAT5 cable you can:
• send uncompressed full HD 3D HDMI with 7.1ch audio
• HD Audio/ Video/Internet/ IR& RS232/Power, all in
ONE SINGLE Cable Link
• remotely power the receiver
Target Applications:
• IR control the source from the receiver
• HDMI Spec.:1.4 Compatible
• RS232 control the source from the receiver
• DVI Spec.:1.0 Compliant
• use the 3 port hub in the sender & receiver to extend
your LAN
• HDCP Spec.:1.1 Compliant
It also fully supports HDMI v1.4, allowing smooth 3D video
transmission from 3D Blu-ray players to 3DTVs, with fully
HDCP compliance. Built-in 3 x 100Mbps Fast Ethernet RJ-45
ports at both sender and receiver provides internet
connection for TV, Video device and PC. Power Over Cat5
Cable design makes Receiver side powered directly without
extra power adapter to Receiver unit. Convenient IR PassThru function allows video sources to be controlled via IR
remote control from TV/Display which may be located some
distance away.
• Ethernet Network Data: 100/10 Base-TX
538.28
£
Code PE3D4K100A PU1H3HBTE
• Data Speed:Up to 10.2Gbps
PU1H7HBTE
• Ethernet Port: 3x RJ-45 Ports at Sender & Receiver
• RS-232 connector:DB-9 Stanard Female Connector,
Bi-direction transfer & up to 192,000 bps
• IR Pass-Thru:Signal frequency 20-60Khz
• Sender Connector:HDMI Input*1, HD AV Link(RJ-45)
Port*1, Ethernet RJ-45 Port*3, RS232c*1, IR Emiiter
Port*1 DC 24V Input*1
• Receiver Connector:HDMI Onput*1, HD AV Link(RJ-45)
Port*1, Ethernet RJ-45 Port*3, RS232c*1, IR Receiver
Port*1
• Product Dimension:220x83x27mm
Code PU1H2HBTE
Two Way
Code PU1H3HBTL
Three Way (Lite)
Code PU1H3HBTE
Three Way
Code PU1H7HBTL
Seven Way (Lite)
Code PU1H7HBTE
Seven Way
£454.89
£526.71
£790.06
£1053.42
£1699.84
Please note PU514LRX receiver is supplied separately, please see website for details
HDBaseT Lite HDMI Extender
Express Install Multi-room HDMI System
Express Installation Kit - 4 x 4 HDBaseT™ LITE Matrix with PU-514L-RX Receivers. This 4 by 4 HDMI HDBaseT™ Lite Matrix
Express Installation Kit has been developed as a robust and cost effective solution at the heart of any four zone multi-room
environment. Supplied complete with a HDBaseT™ Lite Matrix plus four PU-514L-RX receivers, the kit enables an installer
to easily and confidently configure a 4-zone multi-room AV system using HDBaseT Lite technology and distribute content
throughout the system over a Single CAT5e/6/7 cable infrastructure.
The PU-513/514 systems allow uncompressed HDMI, IR and
RS-232 signals to be transmitted over a Single CAT5e/6
cable to distances of up to 60m.
The Express Install Kit supports the transmission of video (resolutions up to 1080p Full HD and 1920x1200@60Hz), multichannel digital audio, and control via IR, RS-232, or Web GUI/Telnet IP, from four high definition sources to four HDBaseT
outputs over a single CAT5e/6/7 cable (up to 60m) for each output.
Features:
• HDMI 1.4 with 3D, 4K×2K support, HDCP and DVI
compliant
The PU-44XL-KIT is supplied with 4x
PU-514L-RX receivers which utilise the
2-way IR control capabilities of the
matrix.
Use the IP control feature to enable
users to access and control the matrix
remotely and also allow additional
options for integration of third-party
control systems. CYP provide control
drivers for control systems such as
Control 4, RTI, Crestron, AMX, Control
FX, and Demopad. These are available at
no extra cost.
Code PU44XLKIT HDBaseT HDMI over single
CAT6 transmitter and receiver
The PU-107 can send and receive a pure digital HDMI signal
over a single CAT6 cable allowing HD Audio & ‘deep colour’
support.
1768.71
• Supports HDMI 1.4 (including HDCP) over a single
CAT5e/6 up to 60m
• Complies with HDBaseT- Lite specifications
• Full HD resolution support (1080p@60Hz/36-bit), 3D
over 60m, 4Kx2K over 40m and PC resolution support
(VGA to WUXGA) over CAT5e/6 cable
• HDMI input up to 15m with 8-bit deep colour, or 10m
with 12-bit deep colour
• Supports HDMI output up to 15m with 8/12-bit deep
colour
• Supports IR and RS-232 Control
• Supports High Definition LPCM 7.1CH, Dolby TrueHD,
Dolby Digital Plus and DTS-HD Master Audio transmission
£
Features:
• v1.3 HDMI, HDCP 1.1, DVI 1.0 compliant
• v1.3 HDMI over single CAT6 transmitter and receiver set
• Resolution supported: HDTV - 480i to 1080p including
1080p24fps
• High Definition Audio supported: Dolby TrueHD, Dolby
Digital Plus and DTS-HD Master Audio plus LPCM
• Supports CEC bypass
With one-way IR (receiver back to transmitter)
• Supports xvYCC
Code PU513L • Equalises and recovers incoming TMDS data before
re-transmitting to ensure optimum signal quality
With two-way IR control
• Supports Deep Colour (up to 12 bit)
Code PU107 18
165.58
£
Email your order to us at sales@keene.co.uk
Code PE514L £253.78
£255.87
HDMI Over Long Distances
HDMI over CAT5/E Extender
The CYP PU1106 HDMI over CAT6 Extender Set with IR
Pass-through is the perfect solution to extend HDMI signals
via CAT cabling up to 40m. The PU-1106 also allows you to
use your existing Remote Control to control your device
with the included IR Receiver & Blaster.
Features:
• v1.3 HDMI, HDCP 1.1 and DVI 1.1 compliant.
HDMI FAQ
• HDMI over CAT6 Extender Set.
• Resolutions supported: PC - VGA to WXGA; HDTV - 480i
to 1080p plus 1080p24fps.
• High Definition Audio supported: Dolby TrueHD, Dolby
Digital Plus and DTS-HD Master Audio plus LPCM.
• Compatible with CAT-5E and CAT-6 cables. CAT-6 is
recommended for better performance.
• Supports CEC functions & IR blaster.
• Supports ‘Deep Colour’ (10, & 12 bit) - Transmission
distances may be reduced at higher colour depths.
• Equalises and recovers incoming TMDS data before retransmitting to ensure optimum signal quality.
208.43
£
Code PU1106 • Supports xvYCC.
HDMI over CAT5E/5 Multiroom
Distribution System
Features:
• Easy connection and installation
This is a great value HDMI over Cat cable distribution system
that allows you to mix and match between stand-alone and
wall-plate receivers. All types support 3D and provide
IR feedback!
• Supports LPCM/LPCM7.1/DSD/DVD audio Dolby®-AC3/
DTS5.1/DTS-HD/DTS master audio/Dolby® Digital Plus
and Dolby® True-HD audio formats
The sender unit takes a single HDMI
input and transmits it via twin runs
of CAT cable to up to four outputs
up to a distance of 30.0m without
signal loss.
• Supports 24/36bit deep colour video formats
• Can be used with stand alone or wall plate
HDMI receivers
• Requires two Cat5e/6 STP/FTP cables per receiver
(not supplied)
• Power required for the transmitter unit only
This unit receives HDMI signals
sent from the transmitter unit
Specifications:
• HDMI version: High speed with 3D support
This unit is the wall-plate version
which receives HDMI signals sent
from the transmitter unit
• Resolution: 1080P/1080i/720P/576P/576i/480P/480i
• Data transfer rate: Max 6.75Gbps
• Dimensions of transmitter: 111 x 75 x 23.5mm
• Weight of transmitter: 1190g
Code H4T
Code H4SR
Code H4WR
Code H4IRR
Code H4IRE
£229.00
£46.00
£46.00
£8.99
£8.99
4 output transmitter
Stand alone receiver
Wall plate receiver
IR receiver unit
IR emitter
• Weight of power supply: 165g
• Power supply: 9Vdc 4A
• Dimensions of stand alone receiver: 82.4 x 69.5 x 22mm
• IR emitter and receiver lead length: 1.5m
H4KIT2
£399.00
£315.00
£399.00
H4KIT4
You can also use two wall plates as a single room-to-room
option:
Code HWPK
4 output transmitter
£79.99
HDMI 4K Scaler
The SY-4KS HDMI Scaler is designed to upscale 1080p@24 signals to 4K Ultra High Definition (UHD) resolutions, or
downscale a UHD 4K signal to 1080p@24 for integration into any AV system. The ability to downscale 4K signals to
1080p is a crucial function when working with 4K sources in a complex AV system and distributing the HDMI sources to
multiple displays which have varying resolution support. This device allows the user to select the highest commonly
supported resolution between source and display ensuring maximum compatibility in any system. The SY-4KS incorporates
two HDMI outputs, one of which is a bypass (input follows output), and the second is a scaled output. The scaled output
can be set to three modes, upscale to 4K, downscale from 4K, or as a bypass output. Both the bypass output and scaled
output operate simultaneously.
Features
• Supports HDMI upscaling to 4K or downscale to
1080p@24
• Supports HDMI signal bypass
• Simultaneous HDMI outputs
Specifications
• Inputs 1x HDMI [1x HDMI Uncompressed AV and Data]
• 1x USB Mini B [1x Service Port Propriety Data]
• Outputs 2x HDMI [2x HDMI Uncompressed AV and Data]
• PSU: 5V/2.6A
3D from a Blu-ray player will only work via a correctly specified
HDMI cable or an HDBaseT extender. Lower resolution
interlaced 3D from sources such as Sky will work with almost
all of the other extender systems.
I haven’t got enough HDMI sockets on my TV
In this instance you need a switchbox - something that
will take a number of HDMI devices in and let you choose
which one is routed to the output. Switchboxes can be
automatic (switch to last device switched on) or manual (front
pushbutton and/or IR control).
a) A very long HDMI cable
advantages: Preservation of all content. Some of the other
methods will not send multichannel audio for example.
disadvantages: long HDMI cables are usually thicker and
so unwieldy and difficult to route through wall space and
trunking.
Max length usually 20m. Notoriously unpredictable results
depending upon equipment used. IR feedback will require
other equipment.
Code H4KIT1
with 1 x transmitter,
£315.00
I want to go from an HDMI to a scart
This is possible but trickier depending upon what the HDMI
source is. HDMI from a commercial source (such as a DVD
player or set top box) will almost certainly contain HDCP
copy protection (see info panel) and cannot be converted
back to analogue. If the source is non HDCP (eg camcorder)
then there are several boxes to perform this task.
I want to send an HDMI signal to another room
in the house
There are several ways to accomplish this. You can choose
between:
• Dimensions: 33 x 14 x 19mm
Or as complete kits including the IR receivers and emitters:
2 x stand alone receivers,
2 x IR receivers and
1 x IR emitter
Code H4KIT2
with 1 x transmitter,
4 x stand alone receivers,
4 x IR receivers and
1 x IR emitter
Code H4KIT3
with 1 x transmitter,
2 x wall plate receivers,
2 x IR receivers and
1 x IR emitter
Code H4KIT4
with 1 x transmitter,
4 x wall plate receivers,
4 x IR receivers and
1 x IR emitter
I want to go from a scart to HDMI
That’s no problem, but because you are converting an
analogue signal (Scart) to a digital one (HDMI) you need
an electronic box of tricks in the middle. Although we get
asked many times, it is sadly impossible to simply chop an
HDMI plug off and solder on a scart cable in its place. (OK,
it’s not impossible but it definitely wouldn’t work!). There
are plenty of convertors that will perform this task and also
upscale the analogue video signal as well.
Can I send 3D HDMI to other rooms in the house?
• HDCP version: 1.2
You can buy them as individual components:
I want to split my HDMI signal
This requires a Distribution Amplifier - something that takes
one signal in and gives you multiple identical signals out.
You would use one of these where you’d like one source to
be sent to multiple displays.
People also sometimes call these “splitters” as you are in
affect splitting one signal into many. Splitters are more
usually used to refer to analogue audio and video devices
as these can be “split” passively in a crude fashion without
any electronics. A distribution amplifier contains circuitry to
buffer the signal and ensure that each output is the same
as the input. Even if you wanted to you cannot passively
split an HDMI signal (because it is digital) so the correct
terminology is a Distribution Amplifier.
Code SY4KS £167.59
b) HDMI over CAT5/6 (baluns)
advantages: CAT5 cable is cheap by comparison and
flexible so easy to run through wall spaces and trunking.
Max length can be up to 60m.
disadvantages: some models do not provide IR feedback.
some models require two separate runs of CAT5.
c) HDMI over HDBaseT Uses different technology to
other HDMI over CAT5 extenders to give amazing results.
advantages: One single CAT5E cable send crystal clear 3D
HDMI at 1080P with 7.1channel audio and also provides IR
control, RS232 and extend your 100Mbps LAN.
disadvantages: relatively expensive
d) HDMI over IP network
advantages: If the IP network is already installed then no
extra cabling is required. Can also be used with homeplug
ethernet over mains adaptors. IR feedback is built into the
unit. Plug and play with no configuration. Other network
receivers can easily be added in different rooms.
disadvantages: The audio output is stereo not
multichannel. The IP router needs to be compatible with
multicast. The HDMI signal is dynamically compressed
(although in practical terms it’s extremely hard to notice).
e) Wireless HDMI video sender
advantages: neat and tidy - no cables to worry about. IR
feedback built in. Easy to move from room to room. The
HDMI signal is uncompressed.
disadvantages: relatively short range, most suited to
within room or adjacent room use.
Find product information and data sheets on www.keene.co.uk
19
Power Solutions
Internet Controllable Mains Switch
New from Keene, the IPMSW1 is an IP controllable mains power switch. It has two independent mains outlets that
can be controlled in a number of ways.
What is X10?
Features:
• Simple browser button based on / off control.
• Full browser based set-up and timer configuration.
• Adjustable power fail re-start options allow each
switch to delay up to 255 seconds before switching
on. Ideal for remote re-start of systems that require
2 stage start ups.
• 3 timer events per switch with daily weekly or
monthly repeats.
• During each timer event the switch can be set to
either on or off.
• Own IP address, so can be controlled via internet
using port forwarding.
• Support for DDNS.
• Manual override button for each switch.
• Optionally use internet time servers to set
internal clock.
• Internal “Real Time Clock” IC with 5 year
battery backup.
Code IPMSW1
119.99
£
Power Ethernet Sockets
Mains Conditioner For Home
Cinema And Hi Fi
A useful upgrade for any setup, this is an affordable
yet extremely well designed unit that delivers impressive
results. This unit contains a powerful Mains Conditioning
Filter which will reduce or eliminate mains interference
coming through the mains electric supply and help
to enhance your sound and picture quality. It also
incorporates Surge Protection for complete piece of mind.
Specifications:
• Max Current rating 13A
•Max Surge Protection L-N 6500A, L-E 4500A,
N-E 4500A
• Max Voltage Spike Protection 6,000 Volts
Features:
• 2m Screened Mains Lead to prevent RFI
‘What Hi-Fi Magazine gave this a 5 star Award:
“The six-way mains conditioner delivers truly dynamic audio
gains. Comparing it’s performance to the ‘unconditioned’
sound, our reference CD/Amp system enjoys greater separation
and focus of sound, and greater clarity and confidence in the
mid range. Bass is burlier and better integrated, too. In a
nutshell? It really does work.”
Code CS929
29.99
£
The PE200AV Power Ethernet Sockets embed all the
electronics inside a standard wall power socket. The
technology allows the use of the existing mains cables
as a way to transmit high speed data and
environmental services throughout the building
without the cost and disruption of installing
additional cabling.
• No rewiring required
• Simple to install by any electrician – simply replace
a power socket with an Power Ethernet Socket
• Reduces infrastructure costs by using existing mains
cabling throughout the building
• Minimises installation disruption — no need to lift
floor panels and replacing a socket is quick and
easy
• All Ethernet points automatically mesh together
into a secure network without needing a patch
panel and Ethernet switch
• Much cheaper to replace existing power sockets
with PE Sockets than to add additional structured
cables
Code PE200AV
each
for two
for four
£79.00
£156.00
£300.00
X10 Appliance Module
X10 Lamp Module
AM12 Appliance / Switch Module
Gives you instant X10 control of any plug in lamp.
Plugs into a 13 amp socket and will switch on/off lamps
plugged into the module's standard 3 pin socket. In
addition it can dim/brighten (standard tungsten or
halogen filament bulbs only, NOT fluorescent).
Simplicity itself, just unplug the device you want
controlled, plug this into the socket then plug the
device back in. Set the X10 address as needed and you
now have instant X10 control. The module can switch
on or off an appliance of up to 13 amps, ideal for
kettles, fans, heaters, lamps, etc.
For appliances and low energy
lamps
Load 40W (minimum) 300W
(max) incandescent lamps only.
Soft start and smooth dimming
features.
Can be regulated from 0%
lighting to the desired dim
setting.
Code AM12U
20
£22.30
X10 is a communication protocol for remote
control of mains electrical devices. It works by
passing control signals through your existing
mains wiring. There are two essential parts to
an X10 installation; a transmitter and a receiver.
The transmitter generates the control signal
(‘switch on’, ‘switch off’, ‘brighten’ or ‘dim’)
and these signals are acted upon by receiver
modules connected to the mains within the
house. In essence, X10 allows you to assign
a unique "address" to every electrical item you
want controlled. Commands can then be sent
to each particular address, allowing items to
be turned on and off, (or dimmed) as required.
There are a number of different ways to send
a command to an "address", either by a timer,
remote control, computer control, wall switch
or even by telephone. You can have up to 256
unique addresses per house, and of course
some devices can be set to the same address
so that one command can switch them all on or
all off at the same time. You can buy individual
modules to build a system, or buy a starter kit to
get you going. Because X10 uses your existing
house wiring there are no extra cables to run
and the beauty of the system is that you can
expand it almost endlessly. Most of the X10
products require no DIY skills at all, you just plug
the devices in and start using them. A few of the
products (wall switches etc) do require some
basic electrical DIY skills for safe installation
and operation. (As ever, if you're in doubt please
consult a qualified electrician.)
Code LM12U
£22.30
Many more X10 modules and
controllers to choose from on
www.keene.co.uk
X10 Transceiver Module
The transceiver module catches the radio signals
emitted by any X10 compatible transmitter (eg KR22E,
SS13E etc) and converts them into X10
signals for the mains wiring. It simply
plugs into the mains wherever you find
convenient and looks very much like an
appliance module with a small aerial
attached. The transceiver module also has
an outlet socket and can be used like an
appliance module although its address
code cannot be altered from address
code 1. It has an effective reception
range of around 30 metres so normally
one (centrally located) transceiver
module is enough to ensure that an
X10 remote will work more or less
anywhere within the house.
Code TM13U
£19.85
X10 Internet Control
Use your smartphone or tablet to operate your X10
devices. The TIP10RF connects directly to your network
router and sends
commands
wirelessly to
the nearest
transceiver, e.g.
TM13U. No need
to leave your
computer turned
on. Download
the free Android
app from the Play
Store. (iOS app to
follow shortly.
Code TIP10RF
Email your order to us at sales@keene.co.uk
£53.95
AV Plates & Panels
Scart outlet plates
15pin HD outlet plates
19" AV Rack Panels
Scart outlet plate which fits a
standard UK single pattress and
provides a scart socket. The rear
of the sockets have solder type
connections.
Standard size white wall single
outlet plate with a 15pin HD
female connec­tor. The rear of
the plate also has a 15pin
female socket making it easy to
connect to premade 15pin
HD cables.
Rugged 19 inch AV patch panels powder coated black.
Code HCP11
white
Code HCP11S
steel finish
£3.99
£14.99
Code HCP21
white
Code HCP21S
brushed steel
24 x "F" Socket couplers 1U
£9.99
£15.99
15 pin QC plate
Scart outlet plate QC
The HCP21 15 pin HD wall
outlet plate is also now available
in a “quick-connect” solderless
version. This “QC” series plate
has both an internal 15 pin HD
female socket as well as screw
terminals meaning you use premade cables or make solderless connections to bare
wire ends. The terminal blocks are rising clamp style 6A
rated and will accept cables up to 1mm sq.
We’ve enhanced the HCP11
scart wall outlet plate to a
“quick-connect” solderless
version. This “QC” series plate
has handy screw terminals
making installation much easier
than with conventional solder
type connections. The terminal
blocks are rising clamp style 6A
rated and can accept cable up
to 1mm sq.
Code PP1
12 Pairs Speaker Posts 1U
Code PP2
Code HCP21QC
Scart outlet plate QC Steel
15 pin QC plate steel
The Quick Connect Scart plate is
also available in a brushed
stainless steel finish.
The HCP21QC is also available in
a brushed steel finish.
£13.99
£79.00
12 Pairs RCA Phono Sockets 1U
Code PP3
£13.99
Code HCP11QC
£60.26
£80.68
8 Sets Composite & Stereo 1U
Code PP4
£80.68
22 x BNC Couplers 1U
Code HCP11QCS
£22.99
Code HCP21QCS
£22.99
Code PP5
HDMI outlet plates
From Keene, a wall plate with an HDMI socket at the
front and a PCB mounted rear socket. The rear socket is
aligned such that a side entry HDMI cable should pass
through one of the side knock-outs in a std metal rear
pattresses. Depending on the size of plug used some
modification to the pattress may be necessary.
Code PP6
single, white
Code HCP26D
double, white
Code HCP26S
single, steel
Code HCP26SD
double, steel
£19.99
£29.99
£39.99
£54.99
Code HCP26FC
single white with flexible
rear connector
Code HCP26FS
single flat brushed steel finish
Code PP7
£29.99
£39.99
24 x CAT5E 1U
14 x HDMI Couplers 1U
£29.99
24 x CAT6 1U
Code PP12
14 x HDMI Couplers 1U
£99.00
14 x 3 Pin XLR Male 1U
Code PP8
Code PP11
£89.00
14 x 3 Pin XLR Female 1U
We can supply this item as follows:
Code HCP26
£89.00
14 x Speakon Sockets 1U
Code PP14
with tie bar
£199.00
16 Port Switchcraft Blank 1U
£34.99
without tie bar
Code BPP16
£69.00
£99.00
Brush Opening 1U
Code PP9
£14.99
Brush Opening 2U
Code PP10
32 Port Switchcraft Blank 2U
£24.99
Choose from a huge range of
Switchcraft chassis mount AV
sockets and couplers on
www.keene.co.uk
Code PP13
£179.00
Code BPP32
£80.68
Find product information and data sheets on www.keene.co.uk
21
IR Distribution Systems
IRBKIT
IR Signals Explained
I think we are all aware that infrared is just light that we
cannot normally see. It is light at the low (red) end of the
visible spectrum, and shares many of the properties of
visible light. Like visible light infrared travels in straight lines
and will not go around a corner unless there is something
about that will reflect it or refract it. Also like visible light it
is reflected by white surfaces and usually absorbed by dark
surfaces.
It is worth noting that IR emitter LEDs, the sort of thing that
is used in remote controls etc, are like a torch and they have
a narrow beam, and will only “shine” onto a narrow area. A
10 or 15-degree beam width is not unusual.
When you press a button on your remote control a
microcontroller switches the IR emitter on and off very
quickly in a predetermined sequence. This stream or
sequence of IR “data can contain up to as many as 50
digits. The IR receiver on the equipment you are controlling
picks up this IR data, sends it to its microcontroller to be
decoded and responds accordingly - or at least it should do!
Why on earth would I want to get an IR distribution
amplifier?
With an ever increasing number of set top boxes, media
streamers, switchers and recorders etc it is often convenient,
in fact sometimes essential for domestic harmony, to be
able to locate much of the equipment in a small room or
cupboard out of sight. Unless you want to get up and go
to the cupboard / room / loft or wherever every time you
want to change the channel or volume, you will ideally need
some means of controlling all this equipment from your
armchair. This is where an IR distribution system comes in.
An IR distribution system is basically expected to receive the
IR signal and then send it out or “emit it” again in another
location. Over the years they have evolved and improved,
and now the IR receiver, the distribution amplifier and
the emitter are usually separate components. The receiver
can be positioned where you find convenient – usually
somewhere near to the display. The receiver picks up the
signal from your remote and sends this to the distribution
amplifier which in turn sends it back out as IR to one or
more emitters to control the equipment. The net effect is
that you can control your hidden equipment as easily as if
you were pointing the remote directly at it.
There are many ways in which the receiver can be
connected to the distribution amplifier, including dedicated
cable, RF aerial cable, wireless (radio) or even an IP
computer network. We hope that you can use this guide to
see what systems are possible and select the right products
to make your own AV system easy for everyone to control.
The classic in-cabinet solution that puts your remote back
in control and routes IR commands to wherever they are
needed. This unit can be expanded to provide a solution
to almost any IR control problem. Multiple input/output
options are available and you can add extra receivers and
emitters as required (see p28~29 for more details). It is
available ready to use in a number of configurations:
Basic Kit
This kit, comprising the Keene IR Distribution Amplifier,
240V UK mains power adaptor, 2 x universal emitter
wands IRUW and instruction leaflet. Requires input device
or IR receiver (not included).
Keene IR Distribution Amplifier Schematic
IR Input
or
KA109
IRPMR
KIRA
(optional) Panel mount
IR receiver
or
or
IRSR
IRWBR
The standard IR
receiver, supplied
with the IRBKITS
(optional) flush wall mount
standard IR receiver.
Also available in
wideband (IRSPW)
Code IRBKIT (seperate system). Use
IR output from KIRA
family of products via
LAN or internet
or
There are four outputs for driving wands at
low power. Low power wands are usually
placed inside a cabinet and aimed directly
at the AV equipment
or
IRSP
(optional) wideband
IR reciever
A simple splitter such as the
KA109 may be used to combine
two sources of IR input.
PMID
(seperate system). Use
the output direct from a
wireless IR sender such
as the Powermid
RF2IR
(seperate system).
Use the output
direct from the
RF2IR system
Basic Kit plus Standard
Receiver and High Power
Wand
This is a complete kit, comprising the Keene IR
Distribution Amplifier, 240V UK mains power adaptor, 1 x
universal emitter wand, 1 x High Power emitter wand,
1 x Standard IR receiver (IRSR) and instruction leaflet.
The main body of the IR distribution amplifier is usually located out
of sight or within the AV cabinet. It operates from 12v DC allowing
for easy integration in marine or travel installations, a mains to
12v adaptor is supplied.
IRUW
The IR Universal wand is for use in low power output and can
be mounted directly on the equipment fascia or positioned on
the shelf.
39.99
£
There is one output for driving wands to high power.
High power wands can be used to control equipment
located up to 10m away.
IRFSW
(optional). A slim, short range emitter for direct attachment to
the equipment fascia.
IRHPW
(optional). A very directional high power long range emitter
for use where the IRUW has insufficient range
IRDW
A single jack plug drives a pair of wands that affix directly
to the equipment fascia and give a visible flash as the IR
signal is emitted
Basic Kit plus Fascia Mount
Receiver
Basic Kit plus
Panel Mount Receiver
Complete in-cabinet IR Distribution solution with 2 x
Universal Wands and a Fascia Mount IR receiver.
This is a complete kit, comprising the Keene IR Distribution
Amplifier, 240V UK mains power adaptor, 2 x universal
emitter wands (see output component [IRUW] page 28),
1 x Panel Mount IR receiver and instruction leaflet.
Code IRBKITSH 49.99
£
Basic Kit Plus Standard
Receiver
This is a complete kit, comprising the Keene IR
Distribution Amplifier, 240V UK mains power adaptor, 2 x
universal emitter wands IRUW, 1 x Standard IR receiver
IRSR and instruction leaflet. (HINT – This is far and away
our most popular kit so if you’re wondering where to start
this is a really good choice. You can easily add to it and
expand the system later if needed.)
Code IRBKITF
49.99
£
Code IRBKITPB
Code IRBKITPW
(Panel mount receiver in black)
(Panel mount receiver in white)
£65.00
£65.00
Code IRBKITS 22
Email your order to us at sales@keene.co.uk
48.00
£
IR Distribution Systems
IRBKIT MINI
The Keene IRBKIT MINI is a very compact IR Distribution
Amplifier. It allows you to use your remote control on
equipment located in positions where your remote
wouldn’t normally work. For example, equipment placed
inside cabinets with closing doors or located on shelves
behind you or around a corner. Because of the compact
size and light weight the IRBKIT mini can also be
attached to the rear of a wall mounted display, ideal for
use with items such as Apple TV®. It also features an
electronically isolated “Direct” input, allowing direct
connection to the IR Blaster output from any other
manufacturers products, very useful with CAT5
Extenders where the single Blaster output cannot control
all of the source equipment.
IRPRO4 SYSTEM
The IR Pro4 Distribution amplifier has some powerful
features for demanding installations. It has four IR
Receiver inputs, and uniquely all four receivers can be
located in the same room if needed. Normally multiple
IR receivers will cause timing issues and poor
performance but the Pro4 has “BestSelect” technology
which automatically locks on to the strongest IR signal
and shuts down the other inputs within a fraction of a
second, only releasing them again when the code
sequence is complete. It also features a direct cable
input to redistribute other manufacturers IR Blaster
outputs and it can drive up to four dual power IR
emitter outputs. The flexible design allows for a
number of configurations that will solve most IR
control problems.
The IR Pro4 is very flexible, allowing for a number of
configurations that will solve most IR control
problems.
IRPRO4 Basic Kit
IRPRO4 with Standard IR
Receiver
•Four BestSelect IR Receiver inputs
•Direct cabled input that can be used with other
manufacturers IR Blaster outputs
•Four IR Emitter outputs for use with any Keene IR
emitters
•USB power option
The unit is very flexible, allowing for a number of
configurations that will solve most IR control
problems.
• USB Power Connection
• Compact Size (60x35x20mm)
• Dual IR Outputs
• Standard IR Receiver Input
• Direct Universal IR Input
IRBKIT Mini with Fascia Mount
Receiver
IRPKIT4 is the basic kit containing the IRPKIT4
Distribution amplifier, USB Power Cable and a UK
mains adaptor.
IRPKIT4S2 Is the Basic kit plus a Standard IR receiver
and two universal IR emitter wands.
IRBKIT Mini supplied with a Fascia mount receiver and
a single emitter. This is designed to allow IR control of
devices out of sight behind the display or cabinet. An
additional IR emitter may be added later if required.
Supplied complete with a mains to USB power supply.
Code IRBKITMF
£65.17
Also available without the mains to USB power
supply. Choose this option if you have have a nearby
spare USB port that can provide power.
Code IRBKITMFC
£58.19
IRBKITMF
Code IRPKIT4 61.74
IRPRO4 with Fascia Mount
Receiver
IRPKIT4F2 is the Basic kit plus a Fascia Mount IR
receiver and two universal IR emitter wands.
87.01
£
£
Code IRPKIT4S2 IRPRO4 with Panel Mount
Receiver
IRPKIT4B2 Is the Basic kit plus a Panel Mount IR
receiver (black) and two universal IR emitter wands.
IRBKIT Mini with Direct Cable
Input
IRBKIT Mini supplied with 2 x IRDW Dual Blinking
Wands (four emitters) and a direct input cable (no
receiver). This is designed to re-distribute the IR Blaster
output from another device, eg HDMI extender.
Supplied complete with a mains to USB power supply.
Code IRBKITMD
£63.71
Also available without the mains to USB power
supply. Choose this option if you have have a nearby
spare USB port that can provide power.
Code IRBKITMDC
87.50
£
Code IRPKIT4F2 99.17
£
Code IRPKIT4B2 £54.41
Find product information and data sheets on www.keene.co.uk
23
IR Distribution
IR Universal Wand
The Universal wand is ideal for most applications and
can be mounted directly onto the equipment fascia or
placed on the shelf in front. Dimensions of emitter:
L 21mm x W 19mm x D 7mm. Fitted with a 1.2
metre cable.
Keene IR Receiver Adaptor
KRECA
Fascia Mount IR Receiver
This device allows Keene IR receivers to be used with other
manufacturers IR distribution systems, for example Xantech,
Onkyo, Harmon Kardon etc. The design allows a number of
parameters to be changed including:
Data (5v or 12v) and Carrier signal (exclude / include).
Supplied complete with a 3.5mm jack to jack 1.2m link cable.
Code IRUW
5.99
£
This IR receiver is designed to be affixed directly to the
fascia on your display. Super fast electronics and a
semi-wideband capability make it really effective to use
whilst it’s compact size makes it very unobtrusive. The
LED provides visual confirmation that the signal has
been received. Typical IR receivers require a minimum
of 10 cycles before they can “lock” onto the signal.
This receiver will work with just 3 or 4 cycles. This fast
circuitry enables it to work with set top boxes that use
very short bursts of IR code (known as RCMM code), as
used for example by some BT Vision set top boxes.
IR Single Blinking Wand
This is a small discrete emitter that can be mounted
directly onto the device's fascia by means of a small
sticky pad. A small red LED 'blinks' each time an IR
signal is emitted as confirmation that the command
has been sent. Dimensions of emitter: L x 10mm x W
10mm x D 5mm. Fitted with a 3 metre cable.
Code IRBW
9.49
£
IR Dual Blinking Wand
The single jack plug drives two IR emitter wands. The
emitters are extremely tiny (just 9mm across) and are
supplied with double sided adhesive pads to affix
directly to the equipment fascia. The emitters actually
flash red as the IR signal is emitted giving visual
confirmation that the IR signal was received and
transmitted correctly.
9.99
Code KRECA 39.99
£
14.99
£
Standard IR Receiver
Standard IR Receiver 40kHz suitable for most
domestic AV equipment.
Anything To Keene IR
Translator KIRT
The Keene IR Translator is designed to allow you to connect
the IR wand output from any device directly into the IR
receiver input of any
Keene IR equipment, such
as an IRBKIT, IRCM, IR
Anywhere module etc.
This is particularly useful
with HDMI video over
distance systems as the
single IR wand output is
usually insufficient for effective control of multiple sources.
The 3 pole input connector is optically coupled and will work
with any connection as positive or negative. Compatible
with IR frequencies between 10Khz - 200KHz.
Code KIRT
Code IRFMR
Code IRSR
12.99
£
Wideband IR Receiver
Wide Band IR Receiver Up to 100kHz – for more
esoteric equipment.
Code IRWBR
18.99
£
£19.99
Also available KIRT12 for non-keene 12v based IR
systems £19.99
Wall Plate IR Receiver
IR Low Power Wand
IR Emitter Shield
IRSR built into a single gang pattress with translucent
finish flush wall plate
Can be attached directly to the equipment facia or will
work up to 4 metres away. Even when attached
directly the equipment will still respond to external IR
signals. For use with the RBKIT low power output
sockets.
Keene IR Emitter Shield. A
soft flexible rubber cover
that will prevent unwanted
IR cross talk.
Code IRDW
Code IRLPW
£
5.99
£
IR High Power Wand
Only for use with the Keene IRBKIT in the "High Power"
output socket. Provides a very high output IR signal
that will operate equipment up to 10 metres away. If
placed inside a cabinet the signal will usually reflect to
operate several items of equipment without requiring
any other emitters. It can also be used with other
Keene IR Distribution amplifers or the IRBKIT low power
socket but will then only perform as a low power
emitter. Not suitable for one-to-one operation.
Code IRSP
Can be used with all Keene
and most other
manufacturers IR Emitters
Panel Mount IR Receivers
* Improves IR Signal to
noise ratio
* Prevents IR signals from interfering with other
equipment
Overall dimensions 37mm x 29mm
Internal space for emitter 27mm x 14mm (widest) x
7.5mm (deepest)
Single IR Shield
3.49
£
7.99
Pack of Four IR Shields
A short range emitter for direct attachment to the
equipment fascia. Low profile design ideal for use in
tight spaces. Dimensions of emitter: L x 25mm x W
9mm x D 6mm Fitted with a 1.2 metre cable.
Code IRSFW
24
7.99
£
• Requires a 16mm diameter hole
• Overall thread length 44mm
• Maximum material thickness 38mm
• Visible bezel diameter 30mm
• Connection is via a 1m cable to 3.5mm jack plug
Code IRPMRW­ white
£
Side Firing Wand
An Infra Red panel mount receiver designed to be used
with any Keene IR Distribution amplifier. This receiver
can be fitted into the cabinet casing or studded wall.
Code IRPMR­ black
Code IRSHIELD
Code IRHPW
9.99
£
Code IRSHIELD4
Pack of Ten IR Shields
Code IRSHIELD10
24.99
£
19.99
£
Email your order to us at sales@keene.co.uk
Code IRPMRB­ brass
Code IRPMRC­ chrome
£29.99
£29.99
£34.99
£34.99
IR Anywhere / Matrix
SKY Digital Remote Control
Link Magic Eye
Sky digital satellite systems have two RF aerial outputs.
The 2nd RF output can be run to a remote television
(typically a bedroom or kitchen) to allow you to view
Sky. Once you’ve done this you can then easily control
the digibox from your second TV by adding a magic
eye; simply connect it in-line with the aerial by the
remote TV, place the remote “eye” on top of the TV and
you now have infra-red control of your
digibox from the remote TV.
Wired Eye
Global IO-Link RF Adaptor
An ingenious device, this utilises the ability of a Sky receiver
to be controlled via its 2nd RF input and provides a “hardwired” in cabinet control solution. Instead of affixing
an IR emitter directly to the receiver front panel you can
now connect the IR output from the IRBKIT, IRCM or IR
Anywhere module directly to this Wired Eye which in
turn sends the correct signal to the receiver via the coax
connection. Gives 100% reliable results and is invaluable in
preventing cross talk in multi-receiver installations.
This device plugs into the multi-pin socket found on the
back of Sky HD boxes that have no RF2 output. It provides
an RF output for RF based viewing at multiple TV locations.
It also enables Infra Red control via the TV Link Sky Eye /
Magic Eye type IR controllers that use the RF2 socket.
If you want to use this for remote viewing via coax please
be aware that the RF output is an analogue signal not a
digital (Freeview) type.
Code IOLINK
Code SKYLINK
£6.99
Code KWE
19.99
£
IR Over RF Aerial Cable
If you’ve used RF aerial cable to run signals to another
TV in the house you can use the same cable for IR
control. The Keene RF2IR product allows IR control
signals to be distributed via conventional aerial coax
cable. The IR receiver is the same as that used by the
common “sky-eye” type systems although it is not
limited to satellite receivers and may be used with
almost all IR controllable AV equipment. It allows easy IR
control from any remote TV that is connected by aerial
cable to the source equipment.
To use simply connect the “eye” receiver in-line with the
TV aerial on the remote TV and the RF2IR in-line with
the aerial at the source. IR signals picked up by the eye
receiver will be relayed along the aerial cable, decoded
by the RF2IR and output to an emitter wand to control
the source equipment. The output from the RF2IR can
also be fed into an IR distribution amplifier such as the
IRBKIT to control multiple items inside a cabinet.
Very effective where wireless RF type solutions don’t
have enough range or in cases where you want to keep
any extra ‘black boxes’ to a minimum.
Other options are available: RF2IRL – If you already own
an IRBKIT distribution system you could save a little and
share the power supply. If you would like an IRBKIT
distribution system as well, you
can also save some money
by buying the two together.
Code RF2IR
Code RF2IRL
Code RF2KIT
with IRBKIT distribution system
£44.99
£39.99
£69.00
Eye Routing Commander
Analogue RF Modulator
Achieve independent control of multiple SKY Receivers
within the same cabinet!
The Keene wideband modulator enables a camcorder,
security camera, DVD, VCR or any other device with AV
(audio video) output to be connected to the aerial
socket of a TV. It can be left permanently connected
and used to distribute signals to other TV’s via the RF
aerial cable. The AV signal can be positioned on any
vacant RF channel between 21 and 69. This means, for
example, that the signal from a security camera could
be introduced into the aerial lead and viewed in the
same way, and as easily as any normal broadcast signal.
There is a seven segment LED display for clear channel
indication, together with a last channel memory in the
event of a power failure.
The KERC is a sophisticated IR Control Distribution
device, designed primarily for use with UK SKY® satellite
decoders that have the RF2 socket. It is particularly
suited to installations of multiple SKY® receivers as it is
able to overcome the problem of receivers of the same
type all responding to the same IR code. The KERC is
able to decode the different modes of SKY® IR control
signals and route them to specific receiver outputs as
required.
It achieves this by making use of a facility already built-in
to the remote control. The supplied remote control for
each SKY® receiver can be set to one of three different
receiver types (standard, SKY+® & SKYHD®) and also to
one of four different modes, (0,1,2 & 3) giving a total of
12 possible types of IR code. The KERC is able to
distinguish between these different types and route the
IR signal accordingly.
Code KERC
Supplied complete with UK mains adaptor
£23.99
Also available bundled with a SKLYLINK Sky Eye
Code IOLINKDEAL
£31.99
Aerial Splitter with DC PassThrough
Aerial splitter/combiner with DC pass through suitable for
use with Skylink and Triax IR control systems.
Female/Male/Male (socket to 2 x plugs)
Code KA121DC
£4.99
Also available as Male/Female/Female
Code KA121DCF
£5.99
Specifications:
•Power: 12vDC 150mA
•Modulation level: Factory set for 75%.
•Composite video plus audio input
•Scart input (can be used as buffered loop
through output)
•RF Channel: (PLL) channel 21-69
•Compact size (120mm x 85mm x 30mm)
•Weight: 150g
BULK PRICING (50+) and
OEM AVAILABLE on this product
99.00
£
Find product information and data sheets on www.keene.co.uk
Code KRFTW
29.99
£
25
IR Anywhere / Powermind
Infra Red over an IP Network, What! Why?
Keene have designed a range of products that are capable of sending and receiving IR signals across an IP
network. This can be across a LAN, say from one room or office to another or even one from one side of the
world to the other via the internet.
There are several ways to make use of this technology. In its simplest form you can use one module as a real
time IR to IP encoder and another module (or group of modules) as real time decoders to receive the IP signal
and transmit as IR wherever the control is required.
Some of the modules also have on-board memory that alows them to learn and store a number of IR codes.
Once the codes have been stored you can access the modules built in web page via any internet browser and tell
it to emit the desired code(s) as required.
There are also a number of PC programs and "apps" specifically designed to send control signals via IP connected
devices. The Keene modules are compatible with an ever growing number of these, and a list is maintained at
www.keene.co.uk/iranywhere
The modules all feature a built in standard (36 ~ 40 Khz) IR receiver, and the IR inputs and outputs are fully
compatible with all of the existing Keene IR Distribution range so many other styles of receivers and emitter
wands can easily be incorporated. The IR output can also be connected to the input of another Keene IR
Distribution amp if required.
local IR control
infra red
KIRA Modules
These modules will receive an IR command, convert it to
packet data and send that data to a predetermined IP
address (usually another IR Anywhere module). The
receiving module will then decode the data and retransmit the IR as originally received. The IR Anywhere
modules are physically identical and can be software
configured as either a receiver, a target, or stand alone
operation. They will operate via LAN, and also via WAN
assuming firewall and routers are correctly configured.
They are supplied either singly or as a pair of modules.
Once correctly configured, one target can receive signals
from multiple receivers. The target can be either an IR
Anywhere module or the IR Commander Matrix.
• Control IR equipment via local network or anywhere in
the world via internet
• Can be combined with IR distribution system for large
installations
• One-to-one or many-to-one control
• Built in Dynamic DNS support
• DHCP plug and play for LAN
internet capable devices
IP
RS232
Code KIRAM
single module
Code KIRA
pair of modules
£59.99
£108.00
KIRA128
direct IR
control of AV
equipment
feed IR output
into other
IR distribution
systems
Other IP
devices
X10 lighting
and appliances
RS232
matrix
switchers
The KIRA128 is capable of storing up to 128 IR codes in
local memory. These codes can then be accessed and
triggered by any device with web browser capability
from local network or internet. For example the image
opposite shows an iPhone browsing one the IRCM's
internal web pages of stored IR commands
Note, this is a web page and not an "app" and so can
be accessed by any smart phone, PDA or other device
with web browser capability.
The Keene IR Anywhere family of products give you easy
internet control of any Infra Red or RS232 products.
There are many ways to use them, for example;
Use two modules with one set to act as IR receiver and one to act as an IR transmitter and connect them both to your
network. Aim your remote at the receiver and it will convert the signal to packet data, send that data to the other
module which will decode the data and retransmit the IR as originally received. You can do this whether the receiver is
in the next room or on the other side of the world!
The KIRA128 can be software configured as either a
receiver, a target or stand-alone. Once correctly
configured, one target can be used as a local IR emitter
for multiple remote receivers. The target can be another
IR Anywhere (KIRA or KIRA128) or the IR Commander
Matrix (IRCM).
Compatible with a variety of Apps such as Demopad, Mote, TouchSquid, TouchControl, Reymote and many more, you
can use your smartphone or tablet to control your AV equipment from anywhere you have an internet connection. Or
access the device from any browser on any internet capable device using the built-in web pages.
Install the IR Commander Matrix and enjoy selective, routable control of multiple devices.
The possibilities are endless! Please see www.keene-electronics.co.uk for full details
The IR inputs and outputs are fully compatible with the existing Keene IR Distribution range so other styles of receivers
and emitter wands can easily be incorporated.
• Control IR equipment via local network or anywhere in the world via internet
• Can be combined with IR distribution system for large installations
• One-to-one or many-to-one control
Code KIRA128
Product code
IR over IP
KIRA
y
y
KIRA128
y
y
KIRARS232
y
IRCM
y
26
Web Browser Control
Code Storage
4
RS232
Routable Outputs
n
n
128
n
n
y
128
y
n
y
128
y
y
Email your order to us at sales@keene.co.uk
74.99
£
IP Control
KIRA RS232
For extended integration options the KIRA RS232
provides IP control for both Infra Red and RS232
signals. This model has no option for an external IR
receiver although its still has an on-board IR receiver
should you need it. In addition to the ability to send
stored IR codes when triggered by IP commands it will
also send stored IR codes when triggered by Keene
defined ASCII commands via RS232.
The KIRARS232 can function as:
• IR to TCP/IP bridge
• RS232 to TCP/IP bridge
• TCP/IP to RS232 (for the CTX35 X10 bridge)
• RS232 to IR (stored codes)
• RS232 disabled (function as KIRA128)
• Supports baud 2400, 9600, 19200, 57600, 115200
DemoControl
The app gives you a graphical front end with
which to access the 128 stored IR codes
within the memory locations of a KIRA128,
IRCM or KIRARS232. The codes are assigned
to three devices (Display, Set-top box & DVD)
and the app can be used on iPhone or iPad.
The app is available on iTunes for free
(search “DemoControl”).
A FREE app now available for the
iPod and iPad from the iTunes store
http://www.demopad.com/democontrollite.html
There is also a full
professional version of the
program available directly
from DemoPad (www.
demopad.com) that allows
you to build custom screens
and control a virtually
limitless amount of devices.
Available at
iTunes
IR Commander Matrix
The most advanced and the most capable IR
distribution system we’ve ever produced!
Code KIRARS232
84.99
£
•Full Matrix Signal Routing - Each IR input can be
routed to any combination of IR outputs. This means
for example an equipment cabinet could house say
three identical Sky receivers, and each one can be
controlled independently from different rooms
•Four IR output channels - each IR output
channel can drive IR emitter wands or slave IR
distribution amplifiers
•Six local IR input channels - Four IR receivers, one onboard IR receiver and one wand input for taking the
output directly from another IR distribution system or
video sender
•IP addressable - Will accept IR over IP inputs from
Keene IR Anywhere modules or from PC’s or
handheld devices, up to 253 different IP addresses
•Internal IR command store - Can store up to 64 IR
codes in local memory, these can then be triggered
by IP command from local network or internet
•Network inputs can be routed based on IP address Maximum flexibility for LAN devices
• Built in wideband IR receiver - May be disabled
if required
•Local inputs are “one way IRDA” compatible - Will
route signals to control all popular set top boxes
•Will act as Dynamic DNS update client - Built in
support for non-static WAN IP addresses
•LEDs indicate which input is active - When IR
activity is detected on one input all other inputs are
momentarily blanked to ensure the signal remains
pure and is cleanly transmitted. (the LEDs may be
disabled if required)
•Expansion module sockets for inputs and outputs Allows an additional 4 input or output module to be
connected via CAT5 cable at a distance of up
to 50m
Broswer Control
The image above shows an iPhone browsing one of
the KIRA128's internal web pages of stored IR
commands
Note, this is a web page and not an "app" and so can
be accessed by any smart phone, PDA or other device
with web browser capability.
Code IRCM
CTX35 RS232 to X10 Bridge
The Marmitek CTX35 communication transceiver can
receive and transmit standard X10 control signals via
the RS232 port. Transmit commands and received data
are in ASCII format and it is directly compatible with
the KIRARS232 giving you the ability to TCP/IP control
your X10 products from anywhere in the world.
Code CTX35
199.99
£
IP Controllable Mains Switch
The IPMSW1 is an IP controllable mains power switch. It
has two independent mains outlets that can be
controlled in a number of ways.
Features:
• Simple browser button based on / off control.
• Full browser based set-up and timer configuration
• Adjustable power fail re-start options allow each
switch to delay up to 255 seconds before switching
on. Ideal for remote re-start of systems that require
2 stage start ups
• 3 timer events per switch with daily weekly or
monthly repeats
• During each timer event the switch can be set to
either on or off.
• Own IP address, so can be controlled via internet
using port forwarding.
• Support for DDNS
• Manual override button for each switch
• Optionally use internet time servers to set
internal clock
• Internal “Real Time Clock” IC with 5 year
battery backup
169.99
£
Find product information and data sheets on www.keene.co.uk
Code IPMSW1
119.99
£
27
IR Distribution
POWERMID KIT DEALS
Devices that give you wireless
control of your AV devices from
another room
This is a Powermid XL kit
that includes one extra IR
receiver so you can control
your equipment from two
different rooms.
POWERMID
The Powermid remote extender system allows remote
control of IR operated equipment from anywhere in
the house. It comprises a pair of small pyramid shaped
devices. The transmitter picks up the IR from your remote,
converts it to a radio signal and beams it to the receiver. The
receiver then converts the radio signal back into IR to control
your devices. Quick and easy to install, and ultra reliable.
Can be used in-room or even through walls and floors. It can
also be used as a wireless room extension for any of the Keene
IR Distribution amplifiers by simply cabling the IR wand output
from the Powermid into the IR receiver input on the Keene
unit using a KLDE6M cable.
Powermid XL kit including a
Powermid Eye twin IR
emitter wand to control two
extra devices.
Code PMIDKIT2 Additional transmitters & Receivers are available:
POWERMID RF Receiver IR Transmitter unit.
This unit receives the RF signal from a Powermid transmitter
and gives out Infra Red.
Code PMIDR
£18.99
24.99
POWERMID IR Receiver RF Transmitter unit.
This unit receives IR from your remote control and gives out
the RF signal to send to a Powermid receiver.
Code PMIDT
£18.99
POWERMID Dual Output Wand
Additional 2 way IR wand for use with the Powermid units.
These wands are designed to take the IR output direct to
the IR receiving eye on your DVD etc. Universal IR Extender
Cable - Works with Marmitek, Speakercraft etc. 2 IR LED’s
(blinking), 3m cable length, 3.5 mm jackplug.
Code PMID A very clever universal remote from Marmitek. It can control
X10 equipment via RF and up to 10 AV devices by infra red
control. It features assignable icons for favourite channels
making it very easy to use, and it can even be personalised
for different members of the family.
• In addition to 10 A/V devices (TV, decoder,
DVD, set-top box etc.), you can also operate
the Marmitek X-10 modules used for
operating lighting and electrical appliances.
8.99
POWERMID 300 Xtra
The Powermid 300X is another wireless IR extender system.
For this one the receiver can be powered by 2 AAA batteries
(with surprisingly long battery life) or via USB if you have a
spare USB port on your display or STB. A mains to USB
power adaptor is also included just in case.
Transmitter & receiver pair
Additional IR Receiver
£
Code PMID300XR £
Additional IR Transmitter
Code PMID300XT 28
35.95
Code PMID300X 23.95
Code PMIDKIT3 48.99
£
MARMITEK Easy Icon Universal
Remote Control
• Guaranteed to work with all your current
and any other A/V equipment you purchase in
the future (extremely comprehensive preprogramming with learning facility).
£
29.99
£
Powermid XL kit including
one extra IR receiver / RF
transmitter unit to allow
control from an extra room,
and a Powermid Eye twin IR
emitter wand to control two
extra devices.
£
• Personalise the remote control for each
member of the family - favourite channels for
you, your partner, children and up to 10
others
Code PMIDEYE 39.99
£
Code PMIDKIT1 • With handy home theatre macro function:
with 1 press of a button you can switch all
your equipment and X-10 lighting to the
correct setting.
Code EZICON Additional
Remotes for Sky
Satellite Systems
64.99
IR Tip
Other sources of infrared include
sunlight, fluorescent lights and
LCD and plasma displays. Keene
IR receivers are carefully filtered
to minimise any interference
that might be caused by these
sources, but it always makes
sense to try and position your
IR receivers carefully. Ideally try
to position the receiver directly
beneath or to one side of the
screen and slightly behind the
face of the screen, do not have
something reflective directly
opposite and try to find a spot
that will not be in direct sunlight.
£
Standard
Sky Digital
Remote
Why would you want
another? Well, if you had
extended control of your
Sky system from other
rooms then you might not
want to or remember to
carry your single remote
controller from room to
room. Solution: have a
remote wherever you
might want to use one.
Simple as that!
12.99
£
Code SKYREM
23.95
£
Email your order to us at sales@keene.co.uk
SKY HD
Remote
SKY Plus
Remote
Code SKYPREM
21.99
£
24.99
£
Code SKY120 IR & AV Cables
IR Link Cables
CAT5 Cable Economisers
For direct connection of the IR Wand output to the IR
receiver input on a Keene IR Distribution Amplifier.
Although CAT5 cables have four pairs of conductors, 10base
and 100base systems only use two of these pairs so half of
the cable is redundant. These cable economisers allow you to
route two IP signals down a single Cat5 cable. Ideal for use
with the IR Anywhere modules as it allows you to add remote
control without having to utilise an extra remote network
hub or switch. Supplied in pairs.(Note: CANNOT be used with
Gigabit networks or anything using POE!)
Code KLDE10M
2.5mm to 3.5mm tip & ring
connected only
£5.99
Code KLDE6M
3.5mm to 3.5mm tip and ring
connected only £5.99
Code KA201 16.99
£
Jack Extension Cables
Kramer BNC Cables HD SDI
Extension leads, 3.5mm stereo jack plug to 3.5mm
stereo socket to be used on input or output as
required. We’ve tested the input up to 10m and the
output to 20m.
These cables are constructed of high performance RG-6 cable
with 75 ohm BNC connectors at each end. They offer
outstanding quality, durability, and high performance for any
video signal application including HD-SDI signals. High
quality connectors - True 75 ohm BNC connectors maintain
correct impedance .
Code KLD40
3M
Code KLD405
5M
Code KLD4010
10M
£4.49
£4.99
£8.99
CAT5 Cable Receiver Extenders
If the Jack cable extenders aren't long enough or you
already have some installed CAT5 cable you'd like to use
then these will solve the problem. This kit consists of a pair
of short (25cm) line adaptors, one with an RJ45 line socket
to a 3.5mm stereo jack plug, and the other with an RJ45
line socket to a 3.5mm stereo jack socket. To use simply
plug the IR receiver in to the 3.5mm jack socket of one
adaptor and the 3.5mm plug of the other adaptor goes
into the IR receiver input of your IRBKIT or IR Commander.
Connect your Cat5/6 (standard wired network cable) in
between the adaptors and that is it. Using this method it
is possible to remote mount IR receivers at distances of up
to 100m.
3 BNC TO 3 BNC RGB
COMPONENT CABLE
High quality three BNC plugs to three BNC plugs.
Gold plated connections.
Application: RGsB or component video
Code SBB301
1.0M
Code SBB302
2.0M
Code SBB304
5.0M
Code SBB305
10.0M
£28.59
£29.99
£39.99
£49.99
3 PHONO TO 3 PHONO RGB
COMPONENT CABLE
High quality three RCA phono plugs to three RCA phono
plugs.
Gold plated connections.
Application: RGsB or component video
Specifications
• Conductor: 18 AWG solid bare copper.
• Dielectric: Skin Foam.
• Outside Jacket Color: Dark gray w/white lettering.
• Outside Jacket: PVC.
• Shield: (A) 61% braid aluminium wire 34 AWG.
Code SBB101
1.0M
• (B) dual-foil/mylar 25% overlap rate.
Code SBB102
2.0M
• Center Conductor: 0.0403 inches, 1.02mm.
Code SBB104
5.0M
Code SBB105
10.0M
• Dielectric: 0.179 inches, 4.57mm.
£29.99
£34.99
£39.99
£49.99
• Outside Diameter: 0.391 inches, 6.95mm.
This is just a tiny fraction of the
many analogue and digital cables we
are able to supply. Please call or visit
www.keene.co.uk for more details
3 BNC TO 3 PHONO RGB
COMPONENT CABLE
High quality three BNC plugs to three RCA phono plugs.
5.99
£
Code KA175 Gold plated connections.
Extra Long CAT5 Cable Receiver
Extenders
If you need to extend even further then the new KA175XLE
uses a line driver meaning you can extend by up to a full
305m reel of CAT5 cable!
Code KA175XLE 19.99
£
Application: RGsB or component video
Code SBB801
0.5M
Code SBB802
0.9M
Code SBB803
1.8M
Code SBB804
3.0M
Code SBB805
4.6M
Code SBB806
7.6M
Code SBB807
10.6M
Code SBB808
15.2M
Code SBB808
15.2M
Code SBB809
22.9M
Code SBB810
30.5M
Code SBB811
45.7M
£2.73
£3.12
£3.90
£4.68
£5.45
£7.79
£9.74
£12.47
£12.47
£17.14
£21.82
£30.39
Code SBB201
1.0M
Code SBB202
2.0M
Code SBB204
5.0M
Code SBB205
10.0M
Find product information and data sheets on www.keene.co.uk
£29.999
£34.99
£39.99
£49.99
29
AV Supports
Centre Speaker Mount
Centre Speaker Wall Mount with Adjustable Arms
Designed for loudspeakers up to 15kg (33lbs)
• Ideal for centre channel speakers, DVD players and
other AV equipment
• Allows speaker to be positioned for optimum esoteric
performance
• Easy adjustment of arm depth
• Simple installation with all mounting hardware
included
Specifications
• Maximum Weight: 15kg (33lbs)
Code BT15 (black)
£12.99
BT77 – Ultragrip Clamping
Speaker Mount
BT8505 Flat Screen Display
Trolley
The BT77 “Ultragrip Pro” Side-Clamp Loudspeaker Wall
Mount is ideal for loudspeakers with curved fronts and
suitable for all types of small to medium loudspeakers.
The BT77 clamps loudspeakers at the side using
“Ultragrip” high friction pads - eliminating the need to
screw into the loudspeaker.
Designed for flat screens 30" to 50" (127cm) / 40kg
• M
odern aesthetic design with coverplate - hides
fixing screws
• Slim line wall bracket ideal for stud (partition) walls
• Simple adjustment - one 13mm locking nut secures
tilt and swivel
• Complete fixings kit for wall mounting included
• Available in Black or Silver
• Speaker Width 135 - 280mm
• Speaker Weight Max 25 Kg
• Tilt 7 degrees (Up or Down)
• Swivel 180 (Left or Right)
• Supplied in pairs
Code BT77
black
Code BT77S
silver
Code BT77W
white
£34.99
£34.99
£34.99
Atlas Loudspeaker Floor Stands LCD Wall Mount with tilt &
• Designed for loudspeakers up to 50kg (110lbs)
swivel up to 23"
• Sound isolating loudspeaker floor stands
• Fillable columns for superior dampening
• Top and bottom isolation spikes provided
• Supplied in Pairs
• Available in different heights
Specification
• Max. Weight: 50kg (110lbs)
• Top plate dimensions: 190mm (7.5”) x 190mm (7.5”)
• Base plate dimensions: 240mm (9.5”) x 240mm (9.5)
• Max weight of speaker: 50kg (110lbs)
Code BT604
40cm height
Code BT606
60cm height
Code BT608
80cm height
Suitable for Non-VESA patterns up to 755 (29.7") x
410mm (16.1")
VESA Compatibility: 300 x 200,
300 x 300, 400 x 200, 400 x
400, 600 x 400
integrated cable management
Product dimensions: Height:
1910mm (75.2") Width:
1000mm (39.4") Depth: 500mm
(19.7") (including wheel castors)
10mm (0.4") tempered piano
black safety glass base (BS6206)
Graphite Black finish
Max Weight: 70kg (154lbs)
Max Dist between Fixings: H:
280mm – 755mm V: 410mm
Code BT8505B
£389.99
black
LCD Wall Mount with tilt &
swivel up to 42"
• Designed for screens up to 23” (58cm) / 15kg (33lbs)
• Full motion mount - ideal for corner mounting
• Fits screens with VESA mounting patterns: 75mm x
75mm and 100mm x 100mm
• Easy tilt adjustment +17°/ -10°
• CLIPLOGIC cable management included
• Simple ‘hook-on’ installation with all mounting
hardware included
• Features 3 swivel points: 180° at wall, 360° at central
pivot point, 240° at interface
• Screen size: 10” - 23”
• Max Weight: 15kg (33lbs)
• 360° rotation for easy screen levelling and to allow
screen to be mounted in landscape or portrait style
• Security locking screws & Allen key provided for
secure installation
• Features ‘OWLS’™ On Wall Levelling System
• Designed for screens up to 42” (107cm) / 25kg
(55lbs)
• Full motion mount - ideal for corner mounting
• Fits screens with VESA mounting patterns: 75mm x
75mm, 100mm x 100mm, 200mm x 100mm and
200mm x 200mm
• Easy tilt adjustment +/-40°
• Features three swivel points: 180° at wall, 360°
central pivot and 240° interface
• CLIPLOGIC cable management included
• Simple ‘hook-on’ installation with all mounting
hardware included
• Screen size: 15” - 42”
• Max. Weight: 25kg (55lbs)
• Security locking screws and Allen key provided for
secure installation
• Features ‘OWLS’ On Wall Levelling System
Colour: Black
Colour: Black
£49.99
£54.99
£59.99
Code BT7513B
27.84
£
Code BT7515B
54.84
£
Universal Soundbar Mount
Projector Trolley
Stealth Onyx Speakers Stands
The ideal solution for mounting a Soundbar Speaker to
your Flat Screen TV
Designed for use with projectors but may also be used
as a portable lectern
Supplied with braked castors and optional levelling feet
for extra stability
Supplied with safety rails and safety strap for secure
installation
• Stealth Onyx AV Speaker Stands with Glass Base.
• Designed for home cinema speakers up to 2kg (4.4lbs)
• Adjustable height: 685mm (27") - 1060mm (42")
•
Includes adaptors for single point, dual point and
keyhole fixings
•
Suitable for speakers using M5, M6 and UNC 1/4" screws
•
Distance between dual point fixings: Min: 45mm
(1.8”) - Max: 67mm (2.6”)
•
Alternative mounting platform supplied for speakers
without fixing holes
• Supplied in pairs
• Maximum Weight: 2Kg (4.4lbs)
• Minimum Height: 685mm (27")
• Maximum Height: 1060mm (42")
• Mounts a Soundbar above or below the screen
•Universal mount suitable for most soundbars and
flat screens
• Use with or without a flat screen wall mount
• Ideal for corner installations with an articulated mount
• Low profile steel brackets
• Max weight of Soundbar: 10kg (22lbs)
• Easy installation - All mounting hardware included
• Adjustable height (with castors):
785mm - 1265mm (30.9” – 49.8”)
• Adjustable height (with feet):
730mm - 1230mm (29.7” – 48.4”)
• Platform dimensions: 290mm x
360mm (11.4” – 14.2”)
• Adjustable tilt: +/-20 degrees
• Inner pole diameter: 35mm (1.4”)
• Outer pole diameter: 42mm 1.6”)
• Easy to assemble
• Max Weight: 25kg (55lbs)
Code BTV914
30
£24.79
Code BT890B
black
Code BT890
silver
£79.99
£79.99
Email your order to us at sales@keene.co.uk
Code BT114B
30.95
£
Camera Suppports
LIBEC TH-650 Tripod & Head
TPV1 Video Tripod
Tracking Dolly with Track
An extremely high quality tripod at a great price, the
fluid head has a counterbalanced mechanism which
compensates for the camcorders weight and holds it
steady at any tilt angle. The head also has a 65mm claw
ball which allows for quick and easy head levelling
regardless of leg position. The legs are made from three
section oval pipe which gives good rigidity and also
have a transport lock to hold them in place when on
the move.
High quality Camlink TP Video Professional Tri Leg
tripod including soft carry case. Ideal for both amateur
and semi-pro applications where a good quality, stable
tripod is required.
Enables you to create super smooth tracking shots with
your own tripod! The dolly has two sets of locating
holes for the tripod legs, which means the tripod can
be used in both high and low positions. It has eight
radial ball bearing wheels which set the track width to
the correct positions as the dolly moves down the track.
The Tracking Dolly is ideal for use on location or in the
studio, all you need is a reasonably flat surface. The
dollies width has been set to allow it to go through
doorways, it has its own levelling system which prevents
any rocking should the track be on uneven ground. It
runs on inexpensive 40mm dia. PVC pipe which can be
supplied or is available from DIY stores. The dolly will
accept all tripods that have feet smaller than 45mm in
diameter or with a base spreader, 3 straps are supplied
for securing your tripod to the dolly and also supplied
are 2 track
connectors for
joining your track.
Specifications:
•
Height, fully
extended
150cm,
Specifications:
•
3 Section Tri Legs (Removes whip at the start
of a pan)
•
Friction (Fluid
effect) Damping
Head
• With 2 Handles
•
With Quick
Release Plate
•Hieght, folded
75cm
• Ball Leveling
• Weight 3.2kg
• Spirit Level
•
Camera load
capacity : up to
4kg
•
Size:- L770mm.
xW620mm.
xH70mm.
• Rubber Feet
•
Tilt Range
–85 / +85
•
Tripod section :
Single stage
• Weight:- 3kg.
• Pan Range 360
•
Supplied with
carrybag
Code TH650 £169.00
•
Transit size:770mm.
x180mm.x180mm.
•
Max. Operating
Height 137cm
• Folded Length 73cm
Spare quick release plate
Code TH650PL £24.99
LIBEC TH-950 Tripod & Head
Due to smaller and higher performance hand held
camcorders constantly entering the market, the industry
enjoys an increasing demand for tripods and heads for
such camcorders. Ever since it was introduced, the
competitively priced high performance TH-950DV has
been one of the world's most popular tripods in its
class.
The removable camera quick release plate is fitted with
a sliding screw for fine adjustment and is made from
extraordinarily strong magnesium alloy. A disc calliper is
used for the tilt brake to hold the head rock steady and
a 75mm ball head makes levelling smooth and steady.
Code TPV1 £125.95
TPV1 Video Tripod Kit Deal
Kit price includes:- Tracking Dolly, 3 straps, 6 Track
Connectors & 12 metres of Track.
(8 x1.5m = 6 metre run)
£329.99
Code D5T Headrest Mount
The headrest mount enables the camcorder to be
mounted onto a car's headrest. It is fully adjustable for
the different widths of headrest. The camcorder
attaches to a ball mount, so the camera can be set to
the required position. You get a great view from the
drivers prospective or it can be used to video inside the
vehicle. (Only suitable for headrests with twin posts)
A complete kit
containing the
Konig branded
version of the
excellent TVP1
Tripod above
together with a
Konig tripod
Dolly.
Ideal forMini DV cams & all types of handheld
Camcorders up to 2kg.
Specifications:
•
Height, fully
extended
155cm,
Code TPV1KIT •Height, folded
75cm
£169.00
Code CHM £58.29
Libec Tripod Dolly
Mini Motion Cam
•
Camera load
capacity: 4Kg
Designed for use with the TH650 tripod, but also works
well with the TH950.
•
Ball base:
75mm
It is foldable for easy carrying and locks into the open
position by a quick release latch.
The Hague Mini Motion-Cam is a handheld stabilizing
system which is ideal for small lightweight camcorders
or cameras between 0.3kg. and 0.8kg. in weight.
• Weight: 3.75Kg
It also has a braking device on each wheel to avoid
accidental movement when filming.
•
Supplied with
padded carry
case
Sliding screws lock the tripod feet into position to avoid
unwanted movement between the tripod and dolly.
• Supports up to 1.25kg. with additional weights.
• Ideal camera weight 0.3kg. to 0.8kg.
• Quick & simple to set up
• Smooth camera movement
• Eliminates camera shake
The camcorder fits directly onto the stabilizer with
adjustment for moving the camera forward and back
for balancing.
Code TH950 £279.00
Spare quick release plate
Code TH650PL £49.99
Code TL2 £95.00
Find product information and data sheets on www.keene.co.uk
Code MMC £75.00
31
Audio
Rode Podcaster Broadcast USB
Microphone
Seamless integration was the idea, and it was obtained
by creating a studio dynamic microphone with
unparalleled A/D convertors, so that the microphone
can be plugged into any computer with no in/out
boxes, no expensive computer pre-amps, just a USB
cable. The Podcaster offers an end-address
configuration, the clarity of RODE’s tailored-for-voice
frequency response, an ‘ON’ L.E.D, a direct headphone
amp, and of course very low self noise. The mic opens
up possibilities for anyone who records audio - from
podcasters, journalists and students to business people
adding audio files to websites and multimedia
presentations.
• High quality broadcast
sound.
• Dynamic capsule
(neodymium) 28 mm.
• 18-Bit Resolution, 8KHz
to 48KHz sampling.
• Windows and Mac
Rode Smart Lavalier
Microphone
Rode IXY iOS Microphone
The smartLav is a
professional-grade
wearable microphone
designed for use
in a wide range of
film, television and
broadcast scenarios,
or wherever
professional quality
audio is required in
a discreet, portable
format without the
complication and
expense of additional wireless equipment. With the
smartLav the user simply mounts the microphone
on the talent, connects it to a smartphone or tablet
headset jack and records via the RODE Rec app for iOS,
or any other audio app of their choice. By employing
a high quality omni-directional condenser capsule the
smartLav picks up sound equally from all around the
microphone, allowing for versatility when mounting
and ensuring a high degree of user-friendly operation.
compatible.
• Tight Cardioid pattern for superior off axis sound
rejection.
• Powered from USB Bus.
• Includes Microphone Stand Mount and a 3m (40”)
USB cable.
• Internal capsule shock mounting.
• 3.5mm stereo headphone jack output with volume
control.
Power Requirements: Power supplied from USB port.
Weight (mic only):
610g (21.5 oz)
Dimensions:
Length: 215mm (8 ”)
Height: 56mm (2 ”)
Width:
52mm (2 ”)
A foam pop shield is supplied to minimise wind noise
and vocal plosives (hard ‘b’, ‘t’ and ‘p’ sounds), as
well as a durable mounting clip with in-built cable
management. The smartLav is compatible with
any audio app that accepts input from the headset
connection, however it has been designed to pair
perfectly with RODE’s RODE Rec app for Apple iOS
devices. RODE Rec turns the user’s iOS device into
a fully-featured field recorder, with a wide range of
equalisation presets to suit various recording situations,
in addition to professional editing functions and the
ability to publish to SoundCloud and Dropbox direct
from the app.
Code SMARTLAV
£149.00
We also offer the Podcaster in money saving kits:
Podcaster plus PSM1 shockmount
Code RPC1KIT1
£185.00
At the heart of the
iXY is a matched
pair of ½” cardioid
condenser capsules,
fixed in a perfect 90 degree ‘near-coincident’
alignment. This results in immersive and true-to-life
stereo recordings, captured in incredibly high detail.
The iXY is supplied
with a foam
windshield for
outdoor recording as
well as a reinforced
protective zip case
to ensure your iXY is
available whenever
you need it.
For more information
and to hear audio
samples visit
www.ixymic.com.
The iXY is compatible
with iPhone® 4S, iPhone® 4, iPad® (3rd generation),
iPad® 2, iPad® & iPod touch® (4th generation). (NOT
lightning connector)
£36.00
Code IXY
£135.00
Rode NT1A Vocal Pack
Rode VideoMic Go
The World's Quietest Studio Condenser Microphone
Clear, directional audio on the GO! Compact and light
weight by design, the VideoMic GO delivers clear,
crisp, directional audio with incredible ease of use.
Its tight pickup area focuses directly in front of the
microphone and
reduces other
surrounding
sounds,
ensuring that
your subject is
isolated from
distracting
background noise.
The RODE NT1-A has become
an industry standard; delivering
the warmth, extended dynamic
range, clarity and high SPL
capability usually only featured
by some of the most expensive
microphones.
Code RPC1
The RODE iXY is the ultimate recording microphone for
iPhone®, iPad® or
iPod® touch. With
up to 24-bit/96k*
recording and onboard high-fidelity
A/D conversion, your
iXY recordings are
rich, smooth and
accurate.
Now available as the ‘Complete
Vocal Recording Solution’ this
NT1-A package now includes
everything you need to get truly
professional vocal recordings
- the world’s quietest studio
microphone, a studio grade pop
shield and shock mount, a premium 20’ cable, dust
cover, an instructional DVD with recording tips, and of
course RODE’s industry leading ten year warranty.
The integrated Rycote® Lyre® shock mount isolates
your microphone from bumps and vibrations that
could otherwise interfere with your sound.
The VideoMic GO has no complicated switches or
settings and is powered by your camera's external
microphone input, requiring no batteries to operate,
ensuring you never miss a great shot.
Podcaster plus PSA1 angle-poise stand
& PSM1 shockmount
Specifications:
Code RPC1KIT2
£259.00
Large 1" (25mm) capsule with gold plated diaphragm
Cardioid polar pattern, Self noise of only 5dB (A)
Ultra low noise, transformerless surface mount circuitry
Keene are major RODE stockists and
this is just a fraction of the range we
can supply. Please call or check
www.keene.co.uk for more details
32
Wide dynamic range, Gold plated output contacts
True condenser (externally biased), Internal capsule
shock mounting
Code NT1APACK
£139.99
Email your order to us at sales@keene.co.uk
Acoustic Principle
Line Gradient
Capsule
0.50"
Polar Pattern
Supercardioid
Frequency Range 100Hz - 16kHz
Maximum SPL
120dB SPL (@
Output
Minijack Output
Code RVMGO
£62.00
Audio – Microphones
Rode VideoMic Microphone
Rode NGT1 & NTG2 Shotgun
Rode Boom Poles
The RODE VideoMic exhibits low noise and an unusually
wide bandwidth for its size. It is ultra lightweight and
incorporates a shock mount to isolate camera body
noise. Its powered by a standard 9V PP3 type battery
and complete with a low battery LED indicator and a
switchable high pass filter to reduce unwanted low
frequency rumble. It has a standard hot-shoe mount
and can also be attached to a boom arm or tripod. The
connection is via a 3.5mm stereo mini jack.
The RODE NTG1 and NGT2 are lightweight condenser
shotgun microphones, designed for professional
applications within the film, video, television and
production industries.
Designed to be used with directional microphones held
just out of shot, a boom pole allows a subject freedom
of movement and means you don’t need to worry
about visible cables or microphones (as long as you
have a good boom operator that is!) These boom poles
from Rode are precision machined from high grade
aluminium and are lightweight yet easy to adjust to the
desired length with a secure twist locking action. The
poles have Velcro straps to externally secure a mic cable,
or the end caps can be removed and an XLR cable
threaded internally through the tube.
Studio recording quality
Rugged fibre-reinforced ABS construction.
9 V battery operation (not included).
Custom designed integral wind shield.
Condenser Microphone.
Low noise circuitry.
Low handling noise.
Integral hot shoe mount.
Full 10 year warranty (registration required)
The 48V phantom powered NTG1 (phantom operating
power only, NTG2 has additional battery power option)
and NTG2 provides a balanced low impedance output
stage. Wide bandwidth and controlled polar response
coupled with low noise SMT electronics, make the
NTG1 the perfect choice for film, video engineering and
voice-over work. Its light weight making it ideal for
mounting directly to video cameras or on boom poles.
The NTG1 & 2 come
complete with mount and
windshield. The windscreen
effectively suppresses wind
noise when recording
outdoors in moderate
conditions.
They have std 3/8 threads for attaching the mic
or shockmount. Three models are available:
GREAT
VALUE
Standard Boom Pole length (retracted) 0.84m
(extended) 3.0m
£75.00
Code RBP £79.00
£92.00
Code RVM Code RVMDEAL
Mini Boom Pole length (retracted) 0.82m (extended)
2.0m
mic plus Pro windshield
Code RMBP
Rode VideoMic Pro compact
Shotgun Microphone
The RØDE VideoMic Pro raises the bar set by the
original RØDE VideoMic, by combining broadcast
quality audio with an ultra compact and lightweight
ergonomic design.
Incorporating new features specific to high end video,
the VMP also evolves many of the features that have
made the VideoMic so successful. Noise transference
has been significantly reduced using both a revised,
more elegant shock mounting system and a lightweight
premium cable.
• Broadcast recording quality condenser microphone
• Compact design (only 150mm/6" length)
• Ultra lightweight (only 85g/3oz)
• 9V battery powered, with up to 70 hours battery life
(alkaline)
• Integrated shock mounting
• Integrated foam windshield
• 3.5mm stereo mini-jack output (dual mono)
• Two step High Pass Filter (flat, 80Hz)
• Three position
level control
(-10dB, 0,
+20dB)
• Camera shoe
mount with
3/8" thread for
easy boompole
mounting
£139.00
£149.99
Code RVMPRO Code RVMPROKIT
mic plus furry windshield
Tie clip windgag
A furry windjammer
designed for lavalier (tie-clip)
mics to be worn on the
outside of the body.
Supplied with removable
foam inserts that can be
combined with the supplied
foam windgag to ensure a
good fit.
Code WGTC
15.73
£
£69.00
Padded Case, will fit all models complete with mic
attached!
Code RBPBAG
£29.00
Micro Boom Pole lightweight 2.0m (extended)
Code MICROBP
Specifications:
• Output impedance: 250ohm (phantom NTG1)
350ohm battery (NTG2)
• SN ratio: 76 dB (1kHz)
• Maximum SPL: 131dB
(@ 1% THD in 1KOhm)
• Dynamic range: 113 dB
• Power (Supply voltage):
1.5 V AA (NTG2) or Phantom (NTG1/2)
• Current consumption:
2.0 mA
Rode NTG1 (phantom power only)
Code RNTG1 Rode NTG2 (phantom or battery)
Code RNTG2
£149.00
Boundary microphone ATR97
This is a low profile compact omni-directional boundary
microphone from Audio Technica designed for tabletop
use. Ideal for conferences, meetings and placing on the
head table at weddings.
Specifications:
• Size: 58mm Diameter x 15mm high
•Frequency response 50-15000Hz;
Impedance 1000 ohms
•Cable length 1.5m
•3.5mm mono jack plus 6.25mm adaptor
• Power 1 x LR44 battery (included)
• Best suited to camcorders with mini-jack mic sockets
£159.00
Optional “Dead Cat” furry windjammer
is available for this mic
Code DEADCAT
£35.00
£24.99
Rode RNGT2 Kits
Money saving kits:
NTG2 plus RBP Boompole, RSM3 suspension
shockmount & Deadcat Windgag
Code RNTG2BK £279.00
NTG2 plus an RSM3 suspension shockmount
& Deadcat Windgag
Code RNTG2CK
Code ATBM
£209.99
25.99
£
Rode Lavalier Microphone
Whether you’re presenting for television or live on-stage, in a 20,000 seat auditorium or in a house of worship,
The RODE Lavalier microphone has your needs covered. Featuring the pure, clear audio and low handling noise that
RØDE is celebrated for, the LAVALIER is built to deliver and to last. The included water resistant pop filter and minifurry for high wind protection ensure quality recordings in adverse environments, while the anti-trauma water
resistant case provides rugged and secure protection for the microphone, cable and accessories.
Features:
• Ultra discreet appearance
• Incorporated cable
management system
• Ø4.5 mm (Ø0.177")
miniature microphone
• Corrosion resistant stainless steel
• Low handling noise
• RØDE MiCon connector system provides seamless
integration with a wide range of wireless systems
while maintaining discreet and unobtrusive
appearance*
• Gold plated connections
*micon connectors sold separately,
see www.keene.co.uk for details.
Code LAVALIER
Find product information and data sheets on www.keene.co.uk
165.00
£
33
D-SLR
LCD Viewfinder for DSLR HD
Video
The SEAGULL DSLR-LCD FINDER is an essential tool for
any serious film maker. Without it, that grouping of a
small LCD screen, manual focus, razor thin shallow
depth-of-field, camera shake, sunlight and glare makes
shooting a video an hit-and miss affair...........with it,
the control is all yours!
The DSLR LCD Viewfinder is a great accessory for
anyone using a DSLR to shoot video. It solves the 3
major problems:
1. The necessity to view images continuously on the
LCD screen which, in turn, effects stability and thus
focus where the camera has to be handheld away
from the body.
Specifications:
2. The inability to actually ‘see’ any image on that same
screen when working in any bright lighting
conditions.
Magnification - 3x
Optic Glass - 3E3G
Dimensions – 84.5 x 70 x 77mm
Diopter - +/-4
Will fit LCD Size up to 3 inch
3. Trying to ascertain the depth-of-field, even if you can
discern that image.
Comes complete with hand strap
LED Light Ring and Flash unit
New from Seagull, a compact and nicely made LED
light ring with flash function. The power pack and
control unit fits onto the hot-shoe on top of your DSLR
whilst the LED light ring is mounted around the lens via
an adaptor ring screwed direct into the camera's filter
thread.
The light head carries 126 super-bright LED bulbs to
give plenty of illumination. These are controled by the
on-board on / off slider switch and a rotary dimmer
gives you control over the amount of light to be used.
Rather than use the traditional choice of AA or AAA
batteries, the LED126T uses a Sony type lithium-ion
camcorder battery with a hefty 4600mAh capacity
(included) to give plenty of shooting time.
Included in the package is a mains charger for the
battery pack with a choice of three plug adaptors (UK,
Euro, US) so that it can be used in many countries
throughout the world.
The DSLR-LCD Viewfinder solves these problems by
providing a finder that gives you a nice, large 3-inch LCD
image to work with, and then adds a 3x magnification for
extra clarity. What’s more, it features quality optics
consisting of three elements arranged in 3 groups.
Clipping onto the rear of your DSLR finder it provides the
perfect environment for comfortable viewing
incorporating, as it does, a soft motion-picture type
moulded eyecup to block out extraneous light - thus
letting you view a perfect image. It also offers an
excellent range of continuous dioptre variations
between + 4 and -4 to accommodate glass wearers.
The combination of these features allows you to bring
the camera in close to your body for increased stability
and secure viewing and filming.
LED Light Panels
LED126T
Two filters are also included with the light, a frossed
diffusser, and a yellow 'warm' filter. These simply slot
into place on the front.
The LED126T can be either stand or camera mounted
and comes complete with a standard sized cold-shoe
adaptor with locking thumb wheel (this also has a 1/4"
tripod thread in it's base), and a mini-shoe adaptor to
enable the light to be used on the Sony / Canon
cameras with the smaller sized shoe fitting..
Code LCDVF
74.99
£
Specifications:
LED light: Power output 5w
Colour temperature: 5800k
Brightness: 480 lumens
Flash Index: 8.5ft. (ISO100, 1/60s)
Powered by 4pcs. AA batteries (not included)
The control unit has a three position slider switch on
the back for off, light (only) on, and light plus flash on.
The brightness is controllable via a rotating wheel and
so you can tailor your light output to your situation.
The flash function is four times brighter than the
output of the constant light to give you plenty of
oomph for the shot. There is also a test button so you
can experiment before shooting begins.
99.99
£
Code LED126T
LED256T
Also available, a 256 LED version.
Light including battery
Weight: 486gms
Dimensions: 29 x 9 x Depth 3 ins.
It comes complete with six adaptor rings to fit it to 52,
55, 58, 62, 67 and 72mm camera threads, and it can
be adapted easily to other sizes by using additional
stepping rings (please just give us a call as we can
supply most sizes from stock at reasonable prices).
Code MRC80
PROFESSIONAL D-SLR TWIN
BATTERY CHARGER
The Hanel ProCube is a high quality metal bodied
charger for use with Canon (E6) and Nikon (EL14/EL15)
batteries. It will also charge 4 x AA batteries and
provides a high current USB charge outlet making it the
ideal one-charger-does-all companion for pro
photographers on the move. Supplied with UK/Euro/US
mains plugs and as well as a 12v car cigar lead
79.99
£
Compatible with the Canon E6 & HL-E6 / E8 & HL-E8
series and the Nikon EL14 & HL-EL14 / EL15 & HL-EL15
series batteries.
Code LED256T
129.99
£
Black Magic Intensity Pro
Working in HDTV is exciting, however HDV's heavy
compression and limited 1440 x 1080 resolution can
cause problems with video quality and editing. Intensity
Pro eliminates these problems by using direct capture
from the camera image sensor at full 1920 x 1080
HDTV resolution and uncompressed video quality.
Both HDMI and Analogue Connections
Intensity Pro enables you to capture directly from the
HD cameras CCD, bypassing the video compression chip
for true uncompressed video quality. Featuring both
HDMI and analogue video connections means Intensity
Pro works with a massive range of cameras, televisions
and video projectors.
Features:
* Charges 1 or 2 DSLR batteries simultaneously
* Intelligent fast IC charge control with LCD Display
* Integrated 2.1A USB charger.
* Detects & charges most USB devices (iPad & iPhone /
Samsung Note / Tab / all Samsung Smartphones)*
* Includes an AA battery tray for charging of an
additional 4 x AA
* Supplied with interchangeable UK, Euro and US plugs
* 12V Car Lead included
Code PROCUBE
34
57.88
£
Email your order to us at sales@keene.co.uk
Code BINTSPRO
148.15
£
D-SLR
D-SLR Shoulder Rig
Black Widow Spider
Black Widow Belt
This is a lightweight compact rig ideal for DSLR's and
camcorders. It has a gadget bag friendly size when
folded and extends out to provide a variety of different
support options.
Spider Holster for lightweight DSLRs and point-andshoot cameras.
Don’t get us
wrong, the Spider
Holster Black
Widow is
designed to be
very comfortable
when worn on
your own belt. But
our adjustable belt
will make your camera feel like a feather so you can
stay comfortably holstered all day long. One size fits
most, adjustable from 23 - 48 inches.
Features:
• Small (folded) design for easy gadget bag carrying
• Versatile design for many different shooting styles
• Extendable rear arm
• several threaded holes for mounting monitors, lights
& microphones
• All hand grips and joint are rotatable and adjustable
• Non-slip foam hand grips
• No more dangling cameras from your neck
and shoulders
• Both hands and upper body free
• Securely locks your camera in each time it’s placed
into the holster
• Works with your tripod quick-release plate
• Use with your belt or the special Black Widow Belt
(optional)
Code BWB
Specifications:
Got two cameras?
• Weight: 1.1Kg
• Dimensions: 30 x 17 x 8.5cm (folded)
The Spider Holster
Black Widow
includes one Pin,
but you may
purchase an extra
Pin for your second
camera, video
camera or any
device with a
tripod mount.
Code BWS
39.99
£
Spider Pro Single
Camera System
Code BWPIN
The SpiderPro Dual Camera System extends our alreadypopular 1-Camera System, giving you a comfortable
and secure way to carry two cameras while on the job,
or on the go.
•Stainless
steel and
hardened
aluminium,
durable
for active
shooting
situations
•Secure
with a twoposition
lock
59.00
£
Code SPDCS
Code SPSCS
6.99
£
Spider Pro Dual Camera System
Shoot from the hip. The SpiderPro single camera system
contains everything that you need to carry one camera,
including SpiderPro Belt, SpiderPro Holster which
securely attaches to the Belt, SpiderPro Plate which
easily attaches directly to your camera’s tripod mount,
and a SpiderPin which attaches to the Plate and slides
into the Holster to give your camera freedom of
movement at your hip.
Code SCSS
19.99
£
109.94
189.99
£
See www.keene.co.uk
for the full range of
Spider Holsters & accessories
£
Black Magic Intensity Extreme
Professional Performance
Incredible 10 bit HDMI and Analogue video editing with Thunderbolt™
Go beyond the limits of your AVCHD or HDV camera! Simply plug using HDMI or
analogue and capture direct from your camera's CCD! You get incredible quality
that completely bypasses the camera's video compression. Use Intensity for
monitoring from your edit software for maximum real time effects! Intensity
connects direct to your editing software's real time effects processing!
Intensity Extreme, the world’s first 10 bit HD/SD editing solution to feature lightning
fast Thunderbolt™ technology.
The perfect solution for videographers, Intensity Extreme includes SD/HD capture
and playback in compressed and uncompressed video quality. Better still, this
revolutionary new device is compatible with Final Cut Pro 7™, Adobe Premiere
Pro™, Adobe After Effects™, Nuke™, DaVinci Resolve and more.
Machined from a solid piece of aluminum, Intensity Extreme gives you incredible
quality HDMI, component video, s-video and composite 10 bit capture and
playback. Better still, this super-sleek, high-speed data transfer system offers an
incredible 10 Gb/s connection that’s up to 20 times faster than USB 2.0 and up to
11.5 times faster than FireWire 800.
Use Popular Video Software
Intensity works with the software you love to use! Use DirectShow™ and
QuickTime™ software, or the world's most popular editing software such as Final
Cut Pro™ and Premiere Pro™!
Incredible quality HDMI capture and playback!
Intensity lets you capture and playback in the most incredible quality of HDMI and
component analogue video in both SD and HD. Smash the quality barrier for your
video work because Intensity is not only the highest quality, but also affordable!
Code BINTSTBEXT
Find product information and data sheets on www.keene.co.uk
224.00
£
35
A small selection from the AV accessories on www.keene.co.uk
Internet Controllable Mains Switch
Digital TV Anywhere
New from Keene, the IPMSW1 is an IP controllable mains power switch. It has two independent mains outlets
that can be controlled in a number of ways.
Digital wireless sender for all your Digital TV Channels.
Features:
• Watch digital TV far away from the decoder
• Watch and operate the digital TV channels from your
decoder anywhere
• Extra functionality such as Video on Demand, Pay TV,
Electronic Programme Guide, Time Shift and Digital
Video Recorder (DVR) also remain available and
usable
• Place your TV wherever you want,
without having to consider the
location of the aerial or satellite
connection and without laying
cables or drilling holes
• Retain original sound and
picture quality as a result of
digital transmission
• Simple browser button based on / off control.
• Full browser based set-up and timer configuration
• Adjustable power fail re-start options allow each
switch to delay up to 255 seconds before switching
on. Ideal for remote re-start of systems that require
2 stage start ups
• 3 timer events per switch with daily weekly or
monthly repeats
• During each timer event the switch can be set to
either on or off.
• Own IP address, so can be controlled via internet
using port forwarding.
• Support for DDNS
• Manual override button for each switch
• Optionally use internet time servers to set
internal clock
• Internal “Real Time Clock” IC with 5 year
battery backup
Set Contents:
Code IPMSW1
119.99
£
Mighty Brighty Projector Screen Paint & Border
Mighty Brighty turns a wall into a projection screen!
Mighty Brighty is a new and unique concept for
creating a perfect projection screen right on your wall
or any other smooth surface. Just paint it on, sit back
and enjoy. An image projected on Mighty Brighty
Projection Screen Paint has much better contrast and
brightness than that of a plain white wall. It has the
same quality as a professional projection screen. On top
of that you always have exactly the right screen format
for your specific situation. No more struggling to set up
a conventional projector screen. No more bulky ceiling
or wall fixture. Invisible when you are not using it.
How it works
BaseCoat + ContrastBooster
The foundation of the screen is the BaseCoat, which
also determines the contrast level. Based on an easyto-use checklist you determine the right amount of
ContrastBooster to be used. This ContrastBooster sets
the grey level of the BaseCoat for the screen area.
This kit is the MPW 20 Tailor-made Screen & Border Kit
for 6 m2 (64 sq.ft.) of projection screen. The MPW 20
kit includes BaseCoat with ContrastBooster, TopCoat
with BrightnessBooster and MagneCoat with
MagneBorder. All the required tools are included
as well.
• 1.4 litre BaseCoat
• 0.1 litre ContrastBooster for BaseCoat
• 0.9 litre TopCoat
• 0.1 litre BrightnessBooster for TopCoat
• 0.4 litre MagneCoat
• 10 metres / 32.8 ft. of MagneBorder
(width 5.5cm / 2.2") includes all necessary tools.
(other Mighty Brighty kits and accessories are available
– please see keene.co.uk for details.
After applying the BaseCoat, a TopCoat is required.
Using the same handy checklist, you determine the
amount of BrightnessBooster, which sets the gain value
for the TopCoat. Mighty Brighty offers a gain range
from 0,9 up to 1,4, depending on the amount of light
the projector emits and some other criteria.
Code MPW20 Paint & Border Kit
£169.00
Also available MPW10 Standard Kit, contains
Contains 1 BaseCoat (Light Grey) & 1 TopCoat
(Brightness / Gain 1.1) £84.00
Remote Control Mains Socket Set
• Up to 30m range
•Remote control push buttons and sockets are
numbered eg. Button 1 operates socket 1 only
• Manual On/Off switch with LED indicator
• Remote battery (A23A) supplied
• Mains power LED indicator
36
119.70
£
The set comprises a transmitter and a receiver. Connect the
transmitter to the SCART output on your decoder that is connected
to the aerial or satellite connection. Then connect the receiver to the
TV. The set sends on the picture, sound and commands from your
remote control wirelessly.
CELESTRON DIGITAL
MICROSCOPE
The microscope is ideally suited for examining objects
such as coins, stamps, rocks, relics, insects, plants,
gems, circuit boards, various materials, skin, and many
other objects. Also, you can examine specimen slides at
low and high powers.
MagneBorder
The set contains one remote control and three plug in
switches. The plug in switches also have a manual on/off
button and LED status indication.
Code DTVA
A great product for education, discovery, work and fun.
This innovative microscope design allows you to view
specimens or objects on a computer screen and allows
you to take snapshot images or short videos. A rugged,
metal stand is included for holding the microscope
steady at various positions for viewing and/or imaging.
TopCoat + BrightnessBooster
A really easy way to automate your home, use for table
lamps, fans, heaters, anything you like really!
• 1 A/V Transmitter
• 1 A/V Receiver
• 2 Power adapters
• 1 IR Extender cable
• 2 SCART cables
• 2 Stands
• 1 User manual
Contains:
Mighty Brighty offers a range from matt white to ultra
grey (high contrast). All in the same package.
The unique MagneBorder is optionally available.
This border greatly heightens the contrast perception of
images on the screen. A magnetic paint must be
applied prior to the BaseCoat and TopCoat. The
magnetic borders can be easily placed and removed
from the projection area. When the MagneBorder is
removed, all you see is a clear white or light grey wall.
Features:
Specifications:
• Power supply: 230Vac, 50Hz
• Power (max):
13A/2990W
• Dimensions (per
plug in module): 46
x 72 x 140mm
Code RCS3
3 way
Code RCS5
5 way
Specifications:
• Handheld Digital
Microscope Powered
by a 2.0 USB Cable
• Digital Camera - built-in
2MP for Snapshot
Images
and Videos
• Power - 10x to
40x and 150x
• LED Illumination
£14.99
£24.99
Email your order to us at sales@keene.co.uk
Code CDM
45.00
£