Craftsman 139.53800SRT Operating instructions

Model No.
139.53800SRT
For Residential
OPENER
Use
Only
Caution:
Read and follow all
safety rules and
operating instructions
before first use of this
a Safety Precautions
a Assembly
a _nstallation
a Adjustment
a Care and Maintenance
product.
a Operation
Fasten the manual
w Troubleshooting
a Parts List
near the garage door
after installation.
Complieswith UL 325
regulationseffective
January 1, 1993
Sears, Roebuck
and Co., Hoffman
Estates,
IL 60179 U.S.A°
Contents
Page
Contents
Page
Install the lights and lenses ........................................19
Safety information regarding garage door
locks and ropes .................................................................
3
Electrical requirements .................................................
20
Testing your garage door for sticking,
binding and balance ......................................................
3
Illustration of sectional door installation ..........................
4
Install the safety reversing sensor ........................
22, 23
illustration of one-piece door installation .....................5
Connect door arm to trolley (sectional door) ............26
....................................................................
A review of safety alert symbols...o................................2
You eII need tools
3
Carton inventory ................................................................
6
Hardware inventory ..........................................................
7
Assembly section - pages 8 - 11
Assemble T-rait .................................................................
8
Attach belt pulley bracket ......................................................
8
Attach emergency release rope and handle .............19
Safety reversing sensor information .........................21
Fasten door bracket (sectional door) ........................24
Fasten door bracket (one-piece door) ..........................
25
Connect door arm to trolley (one-piece door) ..........27
Adjustment section - pages 28 - 30
Travel limit adjustments .................................................
28
Force adjustments ..............................................................
29
Test the safety reversing sensor ...............................30
Install trolley ...........................................................................
9
Test the safety reverse system ..................................30
Fasten T-rail to opener .................................................
9
Operation safety instructions ...........................................
3t
Install belt ................................................................................
10
Care of your opener ............................................................
31
Set the belt tension ...........................................................
t0
Maintenance schedule .........................................................
3I
Attach belt cap retainer ...................................................
1t
Operation of your opener ...................................................
32
installation section -.pages 11 -27
Receiver and remote control programming ..................
33
installation safety instructions ..................................11
Having a problem? .......................................................
34, 35
Determine header bracket location
Repair parts, rail assembly ................................................
36
Sectional door ................................................................
12
Repair parts, installation .....................................................
36
One-piece door ...................................................................
13
Repair parts, opener assembly ........................................
37
Install the header bracket ................................................
14
Accessories ..........................................................................
38
Attach the T-rail to header bracket ..............................
15
...................................................
Index ................................................................................................
39
Position the opener ................................................................
16
How to order repair parts ....................................................
40
Hang the opener ................................................................
17
Maintenance agreement ....................................................
40
Install the door control
t8
Warranty .....................................................................................
40
Start by Reviewing these important
,=,,,,=,
,,
iii i,,=,,,=,,
,,=
= ==,1=
=r_,,,i
.... =,,_lr
,i,m,
Safety Alert Symbols
i...............................
When you see these Safety Symbols on the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the corresponding instructions. The hazard may
come from something mechanical or from electric shock. Read the instructions carefully.
Mechanical
Electrical
When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage
to your garage door and/or the garage door opener if you do not comply with the corresponding
instructions.
Read the instructions carefully.
This garage door opener is designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the safety instructions contained in this manual.
i
;::............................
= ',
H=,
i
'"'=,'=......
,
......................
You'gW
Need Tools
Dudng assembly, instalfation and adjustment of the opener, instructions will call for hand tools shown below.
.... , ...........
,........
'
,,,=1
.......
Pencil
Hack Saw
Tape Measure
Wire Cutters
C{aw Hammer
3/16", 5/16" and
5t32" Dri!l Bits
ts
Stepladder
Screwdriver
Adjustable
An unbalanced garage door might not reverse
when required and someone under the door
could be seriously injured or killed.
If your garage door binds, sticks or is out of
balance, call for professional
garage door
service. Garage doors, door springs, cables,
pulleys, brackets and their hardware are under
extreme tension and can cause serious injury
or death. Do not try to loosen, move or adjust
them yourself!
Ropes left on a garage door could cause
someone to become entangled and killed.
Remove all ropes connected to the door before
installing and operating the opener.
Identify the type and height of your door and any
special conditions that exist and any additional
materials that may be required by referring to the lists
on page 4 or page 5,
SECTIONAL
DOOR
End Wrench
To avoid damage to the garage door and
opener, disable locks before installing and
operating the opener. Use a wood screw or nail
to hold locks in the "open"
(unlocked)
position.
Operation at other than 120V 60 Hz will cause
opener malfunction and damage.
Before you begin, complete the following test to
make sure your door is balanced, and is not
sticking or binding:
o Lift the door about halfway as shown° Release the
door. It should stay in place, supported entirely by
its springs°
• Raise and lower the door to see if there is any
binding or sticking,
ONE-PIECE DOOR
Before you begin, survey your garage area to
see whether any of the conditions below apply
to your installation.
Horizontal and ve_cal reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door
with glass panels, etc)
See page 24 for details
FINISHED CEIUNG
Supper1 bracket &
fastening hardware
is required.
See page 17
Slack in Belt Tensten
is Non'nat When
Garage Door t$ Closed
Header Walt
Access Door
Sp_ng
0
Safety
Sensor
Floor must be level
edross width of doer
Safety Reversing
Sensor
Header
Bracket
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton,
7'°,
._. Garaga_
ty-&'_y
Door //
spring//
/o/
[_/ Stratghl
= Step 5, page 17 - Do you have a finished ceiling in
your garage? If so, a support bracket and
additional fastening hardware may be required°
. Safety reversing sensor, page 21 - Depending
upon garage construction, wood blocks may need
to be fastened to mounting locations before
sensors are installed.
I
Batl
--
Emergency Release
Rope & Handle
H
%oer!- racke,
= Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor wilt require hardware not
provided_
• The opener can be installed within 2 feet to the left
or right of the door center if there is a torsion spring
or center beadng plate in the way of the header
bracket or door bracket area. ffyour door has
extension springs, the opener must be installed
in the center of the door. See pages t2 and 24.
• Step 11, page 24 - Do you have a steel, aluminum,
fiberglass or glass panel door? If so, horizontal
and vertical reinforcement is required.
• Look at the garage door where it meets the floor.
It must close on the floor all the way across.
Otherwise, the safety reverse system may not
work properly. See page 30. Floor or door should
be repaired.
• Do you have an access door in addition to the
garage door?. If not, Model 53702 Emergency
Key Release is required. See page 38.
You may find it helpful to refer back to this page as
you proceed with the installation of your opener.
• If your door is more than 7 feet high, see the
longer rails available on page 38.
,,,,1111,1,,
Closed Position
Belt Pulley
Bracket
/J
• Step 1, page 12 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
i
/
4
,,,i ...............................
One-Piece Door without Track
Before you begin, survey your garage area to
see whether any of the conditions below apply
to your installation.
FINISHED CEILING
Supportbracket
& fastening
hardwareis required,
Sea page 17,
Slack in belttension
is normal when
garage dooris dosed
Closed Position
Belt
Pulley Bracket
Belt
Trolley
Access Door
O
Emergency
-- Release
Rope & Handie
between floor and bottom
Safety
of door must no1 exceed 1/4",,
Reversing Sensor
Reversing
Sensor
One-Piece Door with Track
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton°
= Step 1, page 13 - Look at the wall or ceiling above
the garage door° The header bracket must be
securely fastened to structural supports.
. Step 5, page t7 - Do you have a finished ceiling in
your garage? If so, a support bracket and
additional fastening hardware (not supplied) may
be required,.
• Safety reversing sensor, page 21 - Depending on
garage construction, wood blocks may need to be
securely fastened to mounting locations before
sensors are installed°
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware that
is not provided.
. Step 11, page 25 - Generally, a one-piece door
does not require reinforcement° If your door is
lightweight, you can refer to the information
relating to sectional doors on page 24°
• Step 11, page 25 - Depending on your door's
construction, you might need additional mounting
hardware for the door bracket.
• Do you have an access door in addition to the
garage door?. If not, Model 53702 Emergency Key
Release is required. See page 38.
• The gap between the bottom of the garage
door and the floor cannot exceed 1/4".
Otherwise, the safety reverse system may not
work properly. See page 30. The floor or the door
should be repaired.
ii
i
Sensor
Closed Position
Belt
Belt
Trolley
Pu{[ey Bracket
I
I
\,eade,
c_,ed %_
I
I
! EmergencyRelease
Garage -Door
y/i_J
Afro
You may find it helpful to refer back to this page
as you proceed with the installation of your
opener.
Opener Carton Inventory
Your garage door opener is packaged in two cartons which contain all parts illustrated below_ If anything is
missing, carefully check the packing material Parts may be "stuck" in the foam. Hardware for assembly and
installation is shown on page 7o
Three-Function Remote Control
with Visor Clip (2)
Premium
Conlrel Consols
Light Lens (2}
_
Belt Cap Retaloer
2-Conductor
Bell Wire
_
Door Bracket Ptate
Header Bracket
Hanging Brackets
Bait
Door Bracket
Safety Reversing Sensor
Mounting Bracket
With Square Holes (2)
"C" Wrap (2)
Curved Door
Am_Section
Safety Reversing Sensor
Mounting Bracket
With Slot (2)
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with
2-Conductor White & WbftetBlack Bell WEre
attached
Straight Door
Arm Section
Safety Labels
and
Literature
Separate all hardware from the packages in the rail carton and the opener carton, as
shown below, for the assembly
and installation procedures.
Assembly
Washered Screw
5/16"-1Bxl/2" (2)
(mounted in opener)
Hex Screw
5/16=-1Bx7/8" (3)
Hardware
Nut
5/16"-18 (5)
Carriage Bolt
114'-20xl/2'
(4)
Spring/Trolley Nut (1)
Master Link (2)
©©
Lock Washer
5/16" (4)
Trolley
Threaded Shaft (1)
....
Installation
Lock Nat
1/4"-20x7/16" (4)
Troltey Clip (1)
I,,I,,,,n,,,=H,In
Hardware
Hex Screw
5/16"ol 8xTtB" (4)
Rail Grease
Handle
_S_rew
5/16"-18xl
-7/8" (4}
Nut 5/16"-18 (6)
Lock Washer 5/16" (6)
Rope
Carriage Bolt
5/16"-!8x2-1t2"
(2)
6ABxl ' (2)
Dry Wall Anchors (2)
fil
Clevis Pin
5/16"x2-3/4" (1)
Insulated
Staples (10)
Clevis Pin
5/16"x1" (2)
Ring
Fastener (3)
Safety Reversing Sensor installation Hardware
Carriage Bob
1/4"-20xl/2'
(4)
Hex Screw
114-20x1-1/2" (2)
Screw
#10-32x318"
(4)
Lock Nut
114"-20 (4)
Wing Nut (2)
o
Lock Nut
#10x32 (4)
InsUlated
Staples (20)
Assembly Section: Pages 8 - 11
To avoid
installation
difficulties,
..................
do not run the garage door opener
until instructed
to do so.
i
Assembly
Make sure bolt necks are
seated in the square
holes and rails are
aligned before you
tighten lock nuts. (See
right and wrong views).
Improper assembly can
cause jerky trolley
operation, noise and/or
nuisance door reversals.
Step 1
Assemble the T-rail &
Attach the Belt Pulley Bracket
- Place the 3 T-rail sections on a flat surface for
assembly. The end sections are identical. Make
sure the "arrow label" on the center section is
pointing toward the door.
• Insert the carriage
seat in the square
and pass through
section. Assemble
Right
bolts so the square bolt necks
holes in the T-rail end sections
the round holes in T-rail center
lock nuts, ensure alignment and
Wrong
T-RAIL BACK
(TO OPENER)
T-rait
tighten.
(End Sec_on)
1/4 _'Lock Nut
\
Q
' tf T-ratl is not assembled
EXACTLY as shown,
trolley will not travel
Jsmoothly along length of
Jrail or it wilt hit against
T-raB
(Center Section)
•
,
Caniage Bott
_,_
t/4"-20x!12'
t the nuts.
T-tall
(End Section)
Belt pulley bracke!
attaches to FRONT
END of T-rail
Square Carriage
Bolt Holes
T-RAIL FRONT
(TODOOR)
• Pos_ion the belt pulley bracket on the front end of the
T-rail as shown. Fasten securely with the hardware
shown.
Hardware Shown Actual Size
©
Lock Nut
1t4"-20x71!6
When
=
O
_
Right
Hex Screw
5/16"-18x7/8'
screws, be
sure to keep
bracket parallel
to
the rail.
tighteningthe
Otherwise, the
rail may bow
Carriage Bolls
1/4"-20xlt2"
Nut
5/16"-18
Lock Washer
5/16"
Wrong
when opener ts
operated.
,,,i,,i
i,,,i,,i
Assembly Step 2
Install
I
!
the Trolley on the T-rail
...........
Ill ......
Trell_
_v
• As a temporary stop, insert a screwdriver into the
hole in the front end of the T-railo
Slide the trolley assembly along the rail to the
s
.,,.
_,,_
._,_._
_'..-'"
screwd,ver
stop
.,.o,,°...°
".°'n°'
°".n°'s
°""°"°",'"°
bolts and nuts were attached from the
wronch g
side and must be repositioned.
._
.,,"-_Y/
Review Step 1,
JJ/_i
f
/,_
5
-,_
_/5t16"-1B
• Insert a 5/16"-t8x7/8" hex screw into the trolley
stop hole in the T-rail as shown° 'Tighten securely
with a 5/16" lock washer and nut, This screw limits
trolley travel in the DOWN direction,
ii
,i
i
HI,I
i
i,,
Assembly Step 3
Fasten the T-rail to the Opener
o Place the opener on packing material to protect
the cover. For convenience, put a support under
the belt pulley bracket.
• Remove the (2) 5/16"-I 8xl/2" washered screws
mounted in the top of the opener°
Washered Screw
5/16"-18xli2"
• Align the holes in the back section of the T-rail with
the holes in the opener.
• Fasten the rail with the (2) washered screws
previously removed. Tighten securely°
Trolley
Remember to use only these screws! Any other
screws will cause serious damage to the opener.
• Insert a 5116"-18x7/8" hex screw into the trolley
stop hole in the T-rail as shown. Tighten securely
with a 5/16" lock washer and nut. This screw limits
trolley travel in the UP direction,
5116"
51t 6"-18
Hardware Shown Actual Size
Hex Screw
5116"- 18x718"
Nut
5116"
i
Lock Washer
5/1 6'
iiii ¸ IIII/II/HN'IHNH'
9
I
' "1 'I'III'IH
_11',
AssombRYJstoP4
fingers
entangled in moving opener sprocket. Attach
belt cap retainer securely.
Never operate
opener while your hand is near the opener
Serious injury can result if
become
sPr°cke.t,_....................
1. Drop the notched side of the trolley clip into the
retaining slot on top of the trolley (see Figure 1).
2. Grasp the clip connector at the end of the belt and
slip it through the belt pulley bracket from behind,
around the pulley and toward the trolley.
3. Fasten the belt clip connector to the trolley clip
with a master link:
Figure 2
op_.er
Sprocket
o Push pins of master link bar through holes in
trolley clip and belt clip connector.
• Push master link cap over pins and onto pin
notches,
o Slide clip-on spring over cap and onto pin
notches until both pins are securely locked in
place.
4. With the trolley against the screwdriver, dispense
the belt along the rail and around the opener
sprocket. The sprocket teeth must engage the
belt (Figure 2).
5. Use the second master link to connect the belt to
the flat end of the trolley threaded shaft (Figure 1)o
Check to make sure the belt is not twisted.
MasterLink
Clip-On Spring
6. Remove the screwclriver.
Master
Unk Cap
MasterLink
Figure I
c,p-o,sp,og
Trolley
Pin Notch
Trolley
Threaded Shaft
Slip Belt Clip Connector
through Pulley Bracket
from thts direction
attach to troflo
Belt
CItpConnector
Belt
Pulley
Belt Clip Connector
7. Insert the trolley threaded shaft through the hole
in the trolley.
8. Hold the belt at the trolley shaft to avoid twisting
as you thread the spring/trolley nut by hand on
the shaft until finger tight against the trolley
(Figure 3). Do not use any tools to tighten belt,
9. Insert a screwdriver tip into one of the slots of the
nut ring, and hold firmly as you release the spring
by turning the nut clockwise with a 7/16" open end
wrench. Turn until the spring snaps open,
Figure 3
When installation is complete, you may notice some
belt droop with the door closed. This is normal, tf the
belt returns to the position shown when the door is
open, do not re-adjust the belt.
10
Nut
H'H'=
'"
I' =1 ''= ....
Assembly Step 5
Attach
the Belt
Cap Retainer
To attach the belt cap retainer:
• Position the belt cap retainer over the opener
sprocket so the two holes in cap align with the two
hoIes in mounting plate. Attach with 8x3/8" hex
screws provided.
Hardware Shown
Actual Size
Belt
Hex Screw
#8x318"
You have now finished assembling your garage door opener. Please read the following
warnings before proceeding to the installation section:
iMPORTANT iNSTALLATiON iNSTRUCTiONS
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW ALL INSTALLATION
INSTRUCTIONS.
2. Install only on a properly balanced and lubricated garage door. An improperly balanced door
may not reverse and could result in severe injury or death. Repairs to cables, spring assemblies
and other hardware must be made by a professional service person before installing opener.
3. Disable all locks and remove all ropes connected to the garage door before installing the opener.
Ropes connected to a garage door can cause entanglement and death.
4. If possible, install door opener 7 feet or more above floor with the emergency release handle
mounted 6 feet above the floor.
5. Do not connect the opener to power source until instructed to do so.
6. Locate the Door Control within sight of the door at a minimum height of 5 feet where small
children cannot reach and away from all moving parts of the door.
7. Install the User Safety Instruction Label on the wall adjacent to the door control and the
Maintenance Instruction Label in a prominent location on the inside of the garage door.
8. Upon completion of the installation, the door must reverse when it comes in contact with a
one-inch high object or a 2x4 laid flat on the floor.
9. Do not wear watches, rings or loose clothing while installing or servicing an opener. Jewelry or
loose clothing can be caught in the mechanism of the garage door or the opener.
11
Rnstallatien
Section:
Pages 12-
27
Installation Step 1
Determine
Header
Bracket
Location
If the header bracket is not rigidly fastened to
a structural support on the header wall or
ceiling, the safety reverse system may not
work properly (see page 30). The door might
not reverse when required, and could cause
serious injury or death.
Installation procedures vary according to
garage door types. Follow the instructions
which apply to your door.
....
H=,
,=
..................
The garage door springs, cables, pulleys,
brackets and their hardware are under extreme
tension. Do not attempt to loosen, move or
adjust them yourself. Serious personal injury
or death could result. Call for professional
garage door service.
Finished
Ceiling
VedicaJ
Guideline
• Close the door and mark the inside
vertical centerline of the garage door.
Structural
° Extend the line onto the header wall
above the door.
Remember, you can fasten the
header bracket within 2 feet of the
left or right of the door center only if
a torsion spring or center bearing
plate is in the way; or you can attach
it to the ceiling (refer to page 14)
when clearance is minimal. (It may
be mounted on the wall upside down
if necessary, to gain approximately
1/2".)
If,you need to install the header bracket
on a 2x4 (on wall or ceiling), use lag
screws (not suppfied) to securely fasten
the 2x4 to structural supports as shown
here and on page 1&
Ceiling
t
Header
• Open your door to the highest
point of travel as shown, Draw
an intersecUng horizontal line
on the header wall 2" above
the high point. This height will
provide travel clearance for the
top edge of the door,
Door clearance brackets are
available for sectional doors
when headroom clearance is
less than 2". See accessory
page 38.
_
Wail
2"
Track
Header
Track
Highest Point
of Travst
Highest Point
of Travel
DOOr
Sectional door
with curved track
Proceed to Step 2, page 14.
12
One-piece door
with horizontal track
Read the Safety instructions
on page 12. They also apply to doors without
tracks.
Header Wail
__Verlical
enter,line
- Close the door and mark the
inside vertical centerline of
your garage door. Extend the
line onto the header wall
H
fl
l!
I[
above
door.
Ill
I;_
I{
1t
I1H
If headroom clearance is
minimal, you can install the
header bracket on the ceiling,
1! [_"
H I_
tl ]H/
See page 14.
• If you need to install the
header bracket on a 2x4 (on
wall or ceiling), use lag screws
(not supplied) to securely
fasten the 2x4 to structural
supports as shown_
11 II_'
]! I11
II I_
]1 IN
H I_
t]
I] _It
fl
lli Conte_Ineef
llr
!
OPTIONAL CEILING MOUNT
FOR HEADER BRACKET
_JuL
Header Wall
Header
HighestPoint
of Travel
Highest Point
of Travel
Doer
2x4
I
',10
Jamb
Ha_ware
o
iT
One-piece door without track
jamb hardware
One-piece door without track
pivot hardware
EXAMPLE
• Open your door to the highest point of travel as
shown. Measure the distance from the top of the
door to the floor, Subtract the actual height of the
door, Add 8" to the remainder. (See Example).
Distance from top of door
(at highest point of travel) to floor ........................... 92"
Actual height of door ............................................. -88"
Remainder ..................................................................
4"
- Close the door and draw an intersecting horizontal
line on the header wall at the determined height.
If the total number of inches exceeds the height
available in your garage, use the maximum
height possible, or refer to page 14 for ceiling
installation.
Proceed
Add .........................................................................
+8"
Bracket height on header wall ...............................
12"
(Measure UP from top of CLOSED door.)
to Step 2, page 14.
13
u ii ir_11_
!
...........
installation Step 2
Install
the Header
Bracket
You can attach the header bracket either to the
wall above the garage door, or to the ceiling.
Follow the instructions which will work best for
your particular requirements.
Fasten the Header Bracket to the Wall
• Center the bracket on the vertical guideline with
the bottom edge of the bracket on the horizontal
line as shown (with the arrow pointing toward the
ceiling).
=Mark either set of bracket holes (do not use the
holes designated for ceiling mount) Odll 3/16" pilot
holes and fasten the bracket securely to a structural
support with the hardware provided
Wall
Mounting Holes
i"
Header
W_l
Lag Screws
5/16"xl 8xl=7/8"
Door
Spring
4
The nail hole ts for positioning
only.You must use lag screws to
mount the header bracket
Optioned
Wall Mounting
Holes
2"
Garage _
Door
"_" "T
Highest
Point or Travel
Hardware Shown Actual Size
Vertical
Center
Line
(of Garage Door)
IiIl1Iit It)
Lag
sa;ew
_16.-,8,,-71_.
Fasten the Header Bracket to the Ceiling
• Extend the vertical guideline onto the ceiling as
shown.
- Center the bracket on the vertical mark, no more
than 6" from the wall Make sure the arrow is
pointing toward the wall. The bracket can be
mounted flush against the ceiling when clearance
is minimal
• Mark holes designated for ceiling mount only Drill
3/16" pilot holes and fasten bracket securely to a
structural support with the hardware provided
Ceiling Mounting Holes
/%
Header
Wall
The r,aJl ho_ ts for positioning only
You must use lag screws to mount
Me header bracket.,
14
Wnsta nation
Step3
--
I
° Position the opener on the garage floor below the
header bracket. Use packing material as a
protective base.
Header Wall
If the door spring is in the way you'll need help.
Have someone hold the opener securely on a
temporary support to allow the T-rail to clear the
spring.
Header
Bracket
Bell Pulley
Brecket
- Position the belt pulley bracket against the header
bracket°
, Align the bracket holes and join with a clevis pin as
shown.
. Insert a ring fastener to secure°
Ring Fastener
Header Bracket
Bracket
Tempora_
Support
Hardware Shown Actual Size
@
Clevis Pln
5116"x2-374"
Ring Fastener
15
nstaUBation Step 4
Position
the Opener
Follow instructions
type as illustrated.
To prevent
damage to steel, aluminum,
fiberglass or glass panel doors, do not rest the
opener on the door without using a 2x4°
which apply to your door
A 2x4 laid flat is convenient for setting an ideal
door-to-T-rail distance.
• Raise the opener onto a stepladder.
You will need help at this point ff the ladder is
not taft enough.
, Open the door all the way and place a 2x4 laid fiat
on the top section beneath the T-rail.
If the top panel hits the trolley when you raise
the door, pull down on the trolley release arm to
disconnect the inner and outer sections. The
trolley can remain disconnected until Step 12 is
completed.
o With the door fully open and parallel to the floor,
measure the distance from the floor to the top of
the door.
= Using a stepladder as a support, raise the opener
to the same distance as the door from the floor (it
wifl be at a slight angle as shown).
• The top of the door should be level with the top of
the opener. Do not position the opener more than
2" above this point.
16
nstaHation
Step 5
Hang the Opener
Two representative installations are shown.
Yours may be different. Hanging brackets should
be angled, Figure 1, to provide rigid support. On
finished ceilings, Figure 2, attach a sturdy metal
bracket to structural supports before installing the
opener. The bracket and fastening hardware are not
supplied. See accessory page 38.
Figure I
o Measure the distance from each side of the opener
to the structural support.
• Cut both pieces of the hanging bracket to required
lengths.
- Drill 3/16" pilot holes in the structural supports.
• Attach one end of each bracket to a support with
5/16"xt-7/8" lag screws°
° Fasten the opener to the hanging brackets with
5/16"-t8x7/8" screws, lock washers and nuts_
• Check to make sure the T-rail is centered over the
door (or in line with the header bracket if the
bracket is not centered above the door).
o Remove the 2x4o Operate the door manually° If the
door hits the rail, raise the header bracket.
Hardware Shown Actual Size
L gSc,e'
5/16"- 18xl -7,t8"
,,,,D
© ©
Hex Screw
5/16"- 18x7t8"
Nut 5./16"-18
Lock Washer 5/16"
17
nstalwatn0n
Step6
lnstafl
_he Premium
I
Control Consoie_
Do not connect
to live electrical
wiring.
Connect only to 24 Volt low voltage wires.
Connection to live wires or higher voltage may
cause serious injury from shock, burn or
electrocution.
Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from al! moving
parts of the door and door hardware.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
The door control is typically attached directly to the
wall. If installing into drywall, drill 5/32" holes and
use the anchors provided° Forpre-wired installations
(as in new home construction), Console models
may be mounted to a standard single gang box
(Figure 2),
t_ Strip t/4"
wire and
the back
white/red
Install the door control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control(s).
of insulation from one end of the bell
connect it to the two screw terminals on
of the door control: white to 2, and
to 1.
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it clearly,
and there are no obstructions to door travel.
2. Pry off cover along one side with a screwdriver
blade (see Figure 1). Fasten with 6ABx1-1/4" selftapping screws (standard installation) or 6-32xl"
machine screws (pre-wired installation) as
follows:
Hardware Shown Actual Size
• Install bottom screw, allowing 1/8" to protrude
above walt surface.
_] Imlmlitiiiiiiiiiiq_
6ABX1-114"
S_w
° Position bottom of door control on screw head
and slide down to secure° Adjust screw for snug
rrL
6-32x _"s_rsw
Control Consote (pre-wired)
• Insert top tabs and snap on cover,
Figure
3, (For standard installation only) Run the bell wire
up the wall and across the ceiling to the opener.
Use insulated staples to secure the wire in
several places. Be careful not to pierce the wire
with a staple, creating a short.
4, Connect the bell wire to the terminal screws on
the opener panel: white to 2; white/red to 1.
5. Position the antenna wire as shown.
To Replace,
Insert
Top Tabs
/
_--.._.T{ Remove,
._
.. "'_
PRE-WtRED
INSTALLATION
Twist
Here
0
BACK VIEW
Lock
PREMIUM
Figure 2
COVER
Opener
Terminal :
Sodom
Moun_ng
- Hole
Light
Dry WNI Anshors
24 Volt
2-Condu_.lor
Bell Wire
Terminat
>Screws
Ltghtecl
1
REMOVE & REPLACE
Top
Mounting
-- Hole
Push Bullon
Staples
iiiLiUiiiiiitili
Drill and install top screw with care to avoid
cracking plastic housing. Do not overtighten.
2-Conductor
Belt Wire
Insulated
Control Console (std installation)
CONTROLCONSOLE
18
6o Attach the User Safety instnJction label to the wall
near the door control, and the Maintenance
Instruction label in a prominent location on the
inside of the garage door,
Do NOT connect the power and operate the
opener at this time. The trolley will travel to the
fut! open position but will not return to the
close position
until the sensor beam is
connected and properly aligned.
See Safety Reversing
Sensor instructions
beginning on page 21,
Page 32 explains how to use the door control.
Install
the Lights and the Lenses
I
install the lights:
o Install a 75 watt maximum light bulb in each
socket. The lights will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the lights wil! turn OFF°
Lens
Tab
_
75 Watt Max
Ught Bulb
Lens
Guide
• If the bulbs burn out prematurely due to vibration,
replace them with standard neck "Garage Door
Opener" bulbs.
Lens
Lens
Tab
install the lenses:
. Apply slight presstire on the sides of each lens
and slide the tabs into the slots in the side panels.
Lens
Tab
• For convenience, the lenses may be installed
after Adjustment Step 4 on page 30.
• Reverse the procedure to remove the lenses,
lnstaiaation
Step 8
Attach the Emergency
Release Rope and Handle
Do not use the red handle to pull the door
open or closed. The rope knot could become
untied and you could fall. Use the emergency
release only to disengage the trolley and, if
possible, only when the door is closed.
* Thread one end of the rope through the hole in
the top of the red handle so "NOTICE" reads dght
side up as shown. Secure with an overhand knot.
The knot should be at least 1" from the end of
the rope to prevent slipping,
Garage doors are heavy. If the door is open
when the handle is pulled, the door could
close inadvertently
if it is not properly
balanced. Serious injury may result to persons
under the door. Make sure the doorway is clear
of persons and obstructions
before pulling
handle when door is open.
oThread the other end of the rope through the hole
in the release arm of the outer trolley.
- Adjust rope length so the handle is 6 feet above
the floor. Secure with an overhand knot.
If it is necessary to cut the rope, heat seal the
cut end with a match or lighter to prevent
unraveling.
Overt_nd
Knot
,
19
iii
Electrical
Requirements
j
To prevent electrocution
or fire, installation
and wiring must be in compliance with local
electrical and building codes.
To reduce the risk of electric shock, your garage
door opener has a grounding type plug with a third
grounding pin. This plug will only fit into a grounding
type outlet.
Do NOT use an extension cord, 2-wire adapter,
or change the plug in any way to make it fit
your outlet.
If the plug doesn't fit into the outlet you have,
contact a qualified electrician to install the proper
outlet.
t
Q
To avoid installation difficulties,
do not run the opener at this time.
Wrong
Right
If permanent wiring is required by your local code, refer to the following
Permanent
Wiring
Connections
To make a permanent connection through the
7/8" diameter hole in the top of the opener
(according to local code):
• Remove the opener cover screws and set the
cover aside.
Ground Tab
Green
Ground
Screw
= Remove the attached 3-prong cord.
= Connect the black (line) wire to the screw on the
brass terminal; the white (neutral) wire to the
screw on the silver terminal; and the ground wire
to the green ground screw_ The opener must be
grounded.
• Reinstall the cover_
Black
- Wire
Wire
WhiteWim
I
do
Tonot
avoid
run installation
the opener difficulties,
at this time.
i I"HH H,,='=',,'=
procedure:
1
'I
2O
The Safety Reversing
Information
you'll
need before
System
you begin the installation
The safety reversing sensor must be connected
and aligned correctly before the garage door
opener wilt move in the down direction. This is a
required safety device and cannot be disabled.
of the safety
reversing
sensor.
Without a properly working safety reversing
sensor, persons (particularly children.) could
be injured or killed by a closing garage door.
Read and follow all instructions.
installation procedures are the same for sectional
and one-piece doors_
To protect small children, install the safety
reversing sensor so that the beam will be no
higher than 4"-6" above the garage floor.
Disconnect power to the garage door opener
before installing the safety reversing sensor.
The brackets must be securely fastened to a solid
surface such as the studs on either side of the door,
or add a piece of wood at each location if installing in
masonry construction.
Be sure power to the opener is disconnected.
The sending eye transmits an invisible light beam to
the receiving eye.. The units can be installed on
either side of the garage door as long as the sun
never shines directly into the receiving eye lens.
Look at the label on the connector end of each case
to identify the sensors.
The brackets must be connected and fastened so
that the sending and receiving eyes face each other
as shown in Figure '1.
The invisible light beam path must be unobstructed_
No part of the garage door (or door tracks, springs,
hinges, rollers or other hardware) can interrupt the
beam white the door is closing, if it does, use a piece
of wood to build out each sensor mounting location to
the minimum depth required for light beam clearance.
If an obstruction breaks the light beam while the
garage door is closing, the door will stop and
reverse to ful! open position and the opener lights
will flash for 5 seconds.
Sensor Beam
4-6" max.
above floor
Figure
•
..__
1:
Facing the door from inside the garage
......
2t
nnsta. tuo
stop1o
!
Install the Sa!ety Reversing Sensor
........
I
Figure 2
Figures 2 and 3 show assembly of brackets and
"C" wrap based on the recommended installation of
the sensors as shown on page 21.,
Mounting Bracket
With Square HoIes
However, Figures 4 and 5 are variations which may
fit your installation requirements better. Make sure
the wraps and brackets are aligned so the
sensors will face each other across the garage
door.
//_._,..,_j
= Fasten the "C" wraps to the mounting brackets
having square holes, using the hardware shown
in Figure 2_
• Connect each assembly to a slotted bracket, using
the hardware shown in Figure 3o
_
"c"Wry
Screws
Figure 3
Note the alignment of the brackets for left and
right sides of the door.
1/4x1_t/2"
Lag Screws
o Finger tighten the lock nuts.
114-20xii2" CarriageBO_ts
(with square shoulder)
o Use bracket mounting holes as a template to
locate and drill (2) 3/16" diameter pilot holes on
both sides of the garage door, 4"-6" above the
floor but not exceeding 6" (See waming on
page 21 .)
• Attach bracket assemblies with 1/4"x1-1/2" lag
screws as shown in Figure 3o
"C" Wrap
• Adjust right and left side bracket assemblies to the
same distance out from the mounting surface.
Make sure all door hardware obstructions are
cleared Tighten the nuts securely.
Mounting Bracket
with Square Holes
1t4"-20
Lock Nuts
Hardware Shown Actual Size
©
#10-32x3/B =
#10x32
Screw
Lock Nut
114x1-1f2'
Lag Screw
Staples
114"-20xlt2"
Carriage Bolts
1/4"-20
Lack Nut
Figure 5
Figure 4
Alternate Floor Mount
Alternate Wall Mount
Wat_
::_i
_;:?i
Sensor with wire
Me°erie0
Braokot
indicator Light
with
Sto,
_-'_
Mounting Bracket
with Square Holes
MountingBracket
with Slot
with Square Holes
_._'C
rap
Attach with
concreteenchors
(notprovided)
O
f,
22
oCentereachsensorunitin a "C"wrapwithlenses
pointingtowardeach other across the door (see
Figure 6
Figure 6).
• Secure sensors with the hardware shown. Finger
tighten the wing nut on the receiving eye to allow
for final adjustment. Securely tighten the sending
eye wing nut.,
• Run the wires from both sensors to the opener.
Use insulated staples to secure wire to wall and
ceiling,,
Indicator
Hex Bolt
- Strip 1/4" of insulation from each set of wires°
Separate white and white!black wires sufficiently to
connect to the opener terminal screws: white to 2
and white/black to 3.
_
Trouble Shooting
1o If the sending eye indicator light does not glow
steadily after installation, check for:
o Plug in the opener. Make sure the Lock Feature is
off. Green indicator lights in both the sending and
receiving eyes wilt glow steadily if wiring
connections and alignment are correct.
o Electric power to the opener°
o A short in the white or white/black wires, These
can occur under staples or at screw terminal
connections,
f the indicator light is offin the receiving eye (and
the invisible light beam path is not obstructed),
alignment is required°
= Incorrect wiring between sensors and opener.
. Loosen the receiving eye wing nut to allow slight
rotation of unit° Adjust sensor vertically and/or
horizontally until the green indicator light glows
with a steady light,.
° An open wire (wire break).
2, If the sending eye indicator light glows steadily but
the receiving eye indicator light doesn't:
- Check alignment.
. When indicator lights are glowing steadily in both
units, tighten the wing nut in the receiving eye unit.
o Check for an open wire to the receiving eye.
Hardware Shown Actual Size
114-20xl _112"
Figure 7
Connect Wire to_
OpenerTerminals
__
Finished
Ceiling
__
Door Control
!
C on r}e_lo n s...,...._.....,.=
Sensor
Cennecltons
/
(doffed line) _
OPENER
/
invisible Light Beam
Sensor
ii
ii,
iii
,111111111
Sensor
ProtectionArea
ii,
23
TERMINAL
SCREWS
0nstaU ation Step 11
Fasten Door
Bracket
Follow instructions which apply to your door
type as illustrated below or on page 25.
A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical
cover the height of the top panel.
brace should
The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of
angle iron are used to create a "U"-shaped support. The best solution is to check with your garage door
manufacturer for an opener installation door reinforcement kit.
| and vertical reinforcement
is needed for lightweight garage doors
(liberglass, aluminum, steel,
doors with gTass panel, etc}
Figure I
ire
Door
Bracket
Location
Look Washer
5/16"
Carriage Bott
5/16"-18x2-1t2'
Door
Bracket
Vertical
/
N16"-18
Guideline
Figure 2
Inside
of Door or
Reinforcement Board
Door
o Center the door bracket on the previously marked
vertical guideline used for the header bracket
installation°
Plate
• Position the bracket on the face of the door within
the following limits:
A) The top edge of the bracket 2"-4" below the top
edge of the door.
Hardware Shown Actual Size
©
B) The top edge of the bracket directly below any
structural support across the top of the door,
• Mark and ddll 5/16" left and right fastening holes.
Secure the bracket as shown in Figure 1 if there is
vertical reinforcement,,
Nut 5/16-18
If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes
for the door bracket, position the door plate over the
door bracket as shown in Figure 2o Fasten securely
with hardware shown in Figure 1o
'
24
Lock Washer 5/16"
Please read and compty with the warnings
They apply to one-piece doors also.
and reinforcement
nnstructions
on page 24.
2x4 Suppo_
Header
Bracket
Horizontal and verlical
reinforcement is needed for
[{ghtwetght garage doors
(fiberglass, aluminum, steel,
door with glass panel, etc,)
Bracket
Vertical
Garage Door
Door
Bracket .,._
Top ofGarage)
Door
(inside
of Doer
PJacement
!
oradoorwIth
no
j
n :
exposed framing or for
{ "
H
,
/
,
Carnage Bolt
/
I
use 5116"x1-1_" lag
screw (not supplied) to
fasten door bracket,
,_
_,'
_
='="
......
../
_J'_
, Center the bracket on the top of the door, in line
with the header bracket as shown° Mark holes°
Hardware Shown Actual Size
° Drill 5/16" pilot holes and fasten the door bracket
with hardware supplied.
© ©
If the door has no exposed framing, drill 3/16" pilot
holes and fasten the bracket with 5/16"x1-1/2" lag
screws (not supplied) to the top of the door°
Nut 5/16"-18
The door bracket may be installed on the top
edge of the door if required for your installation.
(Refer to the dotted line optional placement
drawing.) Drill 3116" pilot holes and substitute
5/16"x1-1/2" lag screws (not supplied)to fasten
the bracket to the door.
25
Lock Washer 5116_
_"
Installation
Connect
Step 12
Door Arm
to Trolley
Follow instructions which apply to your door
type as illustrated below and on page 27.
, =,,=,= ,,=,,,,,=
=,1
Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in
Figures 1, 2 and 3.
Figure 1:
Figure 2:
• Fasten straight door arm section to outer trolley
with a clevis pin° Secure the connection with a ring
fastener.
* Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far
apart as possible to increase door arm rigidity.
o Fasten curved door arm to the door bracket in the
same way as shown.
Inner Trolley
Ring
Fastener
/
O
,,
"_JL
Door
|OI---U
/_"/
_?ol
Straight
/_K Emergency
,crews
DoorArm
Curved
Clevis Pin -_
_
Door Arm
Figure
Figure
I
Hole Alignment
2
Alternative
Figure 3:
, If holes in curved arm are above holes in straight
arm, disconnect straight arm, Cut about 6" from
the solid end° Reconnect to trolley with cut end
down as shown°
° Bring arm sections together.
* Find two pairs of holes that line up and join with
screws, lock washers and nuts,
Lock
_,Io"
/_?/
Hardware Shown Actual Size
ol lq
©
:-----,,
© o
Nut 5116"-18
Lock Washer 5116"
II
\o.w¢
Ring Fastener
O_
" Cut This End
Figure
Hex Screw
5/t 6"-18x7/8"
3
Clevis Pin
5]16"xl"
Proceed to Adjustment Step 1, page 28. Trolley will re-engage automatically when the opener is operated.
=,,==,=,=
H ,=
,
,=,
_
26
l,,,,,,t_
=
Door
Assemble the Door Arm:
Bracket
• Fasten the straight and curved door arm sections
together to the longest possible length, with a 2 or
3 hole overlap,
0--
Ring
Fastener
__,.=_--_
Washers
Cl_StAra_h
• With the door closed, connect the straight door
arm section to the door bracket with a clevis pin.
Nuts
t
° Secure with a ring fastener.
I
5116"
5/16"-18x7/8
Curved
Door Arm
On one-piece doors, before connecting the door arm to the trolley the travel limits must be adjusted, Limit adjustment screws are located on the left side panel as shown on page 28. Follow adjustment procedures below.
1
j_,,,_
!I
I
Closed
Door
Open Door
Adjustment
Door Arm
Doer wilh
Backward Slant
Procedures for One-Piece
Doors
Closed Door Adjustment:
Decrease DOWN limit
Open Door Adjustment:
Decrease UP limit
-'rum the UP limit adjustment screw counterclockwise 5-1/2 turns.
• Turn the DOWN limit adjustment screw clockwise
5 complete turns.
- Press the Wall Control push bar. The trolley will
travel to the fully open position.
oPress the Walt Control push bar. The trolley will
travel to the fully closed position.
• Manually raise the door to the open position
(parallel to the floor), and lift the door arm to the
trolley. The arm should touch the trolley just in
back of the door arm connector hole. Refer to the
fully open trolley/door arm positions in the
illustration. If the arm does not extend far enough,
adjust the limit further_ One full turn equals 2" of
trolley travel.
, Manually close the door and lift the door arm to the
trolley. The arm should touch the trolley just ahead
of the door arm connector holeo Refer to the fully
closed trolley/door arm positions in the illustrationoIf
the arm is behind the connector hole, adjust the limit
fudher. One full turn equals 2" of trolley travel°
Connect the door arm to the trolley.
• Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may
be necessary to lift the door slightly to make the connection.
• Secure with a ring fastener,
• Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position
as shown in the illustration, decrease the UP limit until the door is parallel to the floor.
27
Adjustment
Section:
Pages 28 - 30
Adjustment Step 1
Adjust
the UP and DOWN
Limits
Do not make any limit adjustments until the
safety reversing sensors are completely
installed.
,
IH .....
Improper adjustment of the travel limits will
interfere
with the proper operation
of the
safety reverse system. The door might not
reverse properly when required and could
seriously injure or kill someone under it. Test
the safety
reverse
system
following
all
adjustments to the travel limits. See page 30.
==,1=
......................
Limit adjustment settings regulate the points at
which the door will stop when moving up or down.
The door will stop in the up direction if anything
interferes with door travel. The door will reverse in
the down direction if anything interferes with the
door travel (including binding or unbalanced doors).
To operate the opener, press the Door Control push
button. Run the opener through a complete travel
cycle.
Left Side Panel
• Does the door open and close completely?
• Does the door stay closed and not reverse
unintentionally when fully closed?
tf your door passes both of these tests, no limit
adjustments are necessary unless the reversing test
fails (See page 30).
Adjustment procedures are outlined below. Run
the opener through a complete travel cycle after
each adjustment.
Limit A_ustment
S_ews
Repeated operation of the opener during
adjustment procedures may cause the motor to
overheat and shut off. Simply wait 15 minutes
and try again.
(®
'IL ®)I
"
It-- TRAVm.
Adjustment L.t_o!
Read the procedures carefully before proceeding to
Adjustment Step 2. Use a screwdriver to make limit
adjustments.
How and When to Adjust the Limits
If the door does not open completely
but opens at least five feet
If the opener reverses in fully closed position
Decrease down travel. Turn the DOWN limit
adjustment screw clockwise. One turn equals 2" of
travel
Increase up travel Turn the UP limit adjustment
screw clockwise. One turn equals 2" of travel.
If door does not open at least 5 feet: Adjust the
UP (open) force as explained in Adjustment Step 2.
If the door reverses when closing and
there is no visible interference to travel cycle
If the door does not close completely
Increase down travel. Turn the DOWN limit
adjustment screw counterclockwise. One turn
equals 2" of travel.
If the opener lights are flashing, the Safety Reversing
Sensor is obstructed° Remove the obstruction.
Test the door for binding: Pull the emergency release
handle_ Manually open and close the door. If the door
is binding, call for garage door service, tf the door is
not binding or unbalanced, adjust the DOWN (close)
force. See Adjustment Step 2o
If door still won't close completely, try lengthening
the door arm. (See Page 26°)
If you have adjusted the door arm to the maximum
length and the door still wilt not close completely,
lower the header bracket. See Installation Step t,
pages 12 and 13.
28
.,
'
' i,,= ...........
Adjustment
Adjust
,....................;.......
Step 2
the Force
Too much force on the door will interfere with
the proper operation of the safety reverse
system. The door might not reverse properly
when required and could seriously injure or
kill someone under it. Do not increase the
force beyond the minimum amount required
to close the door. Do not use the force
adjustments to compensate for a binding or
sticking garage door. Test the safety reverse
system following all adjustments
to force
levels. See page 30.
Force adjustment controls are located on the right
side panel of the opener° Force adjustment settings
regulate the amount of power required to open and
close the door.
The door will stop in the up direction if anything
interferes with its travel The door will reverse in the
down direction if anything interferes with its travel
(including binding or unbalanced doors)°
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down
direction and stops in the up direction° Weather
conditions can affect the door movement, so
occasional adjustment may be needed.
ForceA_ustment
Controts
The maximum force adjustment range is 260 degrees,
about 3/4 of a complete tum. Do not force controls
beyond that point. Turn force adjustment controls
with a screwdriver,
Fight Side Panel
Adjustmen!
Label
How and When to Adjust the Forces
Test the DOWN (close) force
Make 10 degree turn adjustments until the door stops
easily. After each adjustment, run the opener through
a complete travel cycle.
Grasp the door bottom when the door is about
halfway through DOWN (dose) travel° The door
should reverse. Reversal halfway through clown
travel does not guarantee reversal on a two-inch
obstruction. See page 30. If the door is hard to
hold or doesn't reverse, decrease the DOWN (close)
force by turning the control counterclockwise.
If the door doesn't open at least 5 feet
Increase UP (Open) force by tuming the control
clockwise. Make 10 degree tum adjustments until
door opens completely. Re-adjust the UP limit if
necessary. After each adjustment, run the opener
through a complete travel cycle.
Make 10 degree turn adjustments until the door
reverses normally° After each adjustment, run the
opener through a complete cycle.
If the door reverses during the down (close) cycle
and the opener lights aren't flashing
Test the UP (open) force
Increase DOWN (close) force by turning the control
clockwise° Make 10 degree tum adjustments until the
door completes a close cycle° After each adjustment,
run the opener through a complete travel cycle° Do
not increase the force beyond the minimum
amount required to close the door.
Grasp the door bottom when the door is about
halfway through UP (open) travel° The door should
stop, If the door is hard to hold or doesn't stop,
decrease UP (open) force by turning the control
counterclockwise.
29
I
, ,,=
Adjustment
Step 3
Test The Safety Reversing
Sensor
° Press the remote control push button to open the
door.
• Place the opener carton in the path of the door.
%
° Press the remote control push button to close the
door. The door will not move more than an inch,
and the opener light(s) will flash°
r
Professional service is required if the opener
closes the door when the safety reversing
sensor is obstructed.
The garage door opener will not close from a
remote control if the indicator light in either
sensor is off (alerting you to the fact that the
sensor is misaligned or obstructed).
The garage door can be closed by pressing and
holding the Door Control push button until down
travel is completed.
i= =,=
i ........
=
,=,
i H,I
Safer,ReversingSensor_
Safety RBversi_Sensor
H=,
,,IHir
i '='HM
H
Test the Safety Reverse
Adjustment
Step 4System
I
= ,,,H,
system may result in serious injury or death to R
persons trapped by a closing garage door. |
Repeat this test once a month and adjust as
I Failure to test and adjust the safety reverse I
needed. ........
Test:
GARAGE DOOR
. Place a one-inch board (or a 2x4 laid flat) on the
floor, centered under the garage door.
l
• Operate the door in the down direction° The door
must reverse on striking the obstruction,
Adjustment:
If the door stops on the obstruction, it is not traveling
far enough in the down direction°
• Increase the DOWN limit by turning the DOWN
limit adjustment screw counterclockwise 1/4 tum_
• Repeat the tesL
On a sectional door, make sure limit
adjustments
do not force the door arm beyond a
straight up and down position. See the
illustration on page 26.
• When the door reverses on the one-inch board,
remove the obstruction and run the opener through
3 or 4 complete travel cycles to test adjustment.
If the door will not reverse after repeated
adjustment attempts, call for professional
garage door service.
Important
safety check
Repeat Adjustment
Steps 1, 2 and 4 after:
• Each adjustment of door arm length, force controls
or limit controls.
° Any repair to or adjustment of the garage door
(including springs and hardware)°
° Any repair to or buckling of the garage floor
• Any repair to or adjustment of the opener.
" i,=
3O
' '=.....
T=I=
IMPORTANT
SAFETY iNSTRUCTiONS
To reduce the risk of severe injury or death to persons:
t. READ AND FOLLOW ALL INSTRUCTIONS.
5. if possible, use the emergency release only
when the door is in a closed position. Caution
should be taken whenever the disconnect cord
is actuated with the door open. Weak or broken
springs may cause the door to fail rapidly,
causing injury or death to persons.
6. KEEP GARAGE DOORS PROPERLY
BALANCED. See page 3. An improperly
balanced door may not reverse when required
and could result in severe injury or death.
Repairs to cables, spring assemblies and other
hardware must be made by a professional
garage door person.
2. Do not permit children either to operate or to
playwith the opener. Keep remote control in a
location inaccessible to children.
3. Operate opener only when the door is in full
view and free from any obstruction. Keep the
door in sight until it is completely closed. NO
ONE SHOULD CROSS THE PATH OF THE
MOVING DOOR.
4. Check safety reversal system monthly. See
page 30. The garage door MUSTreverse on
contact with a one-inch (or a 2x4 board laid
flat) object placed on the floor. If an adjustment
is made to either the force or the limit of travel,
both adjustments may be needed and the
safety reversal system must be checked.
Failure to properly adjust the opener may
result in severe injury or death.
7. Disconnect the electric power to the garage
door opener before making any repairs or
removing the covers.
8.SAVE THESE
NSTRUCTUONS.
Care of Your Opener
The remote control
Limit and force adjustment controls
3-FUNCTtON
Open thisend
Limit Controls
Force Controls
Adjuslment Label
Adjustment L_bel
(Located on the dght side pane|)
(Located on the left side panel}
The lithium batteries should
_ toavold/.___
produce power for up to
heu"
5 years. To replace batteries,
s.___
k_-_-'-_ _J._
use the visor clip or screwdriver
blade to pry open the case as
COMPAO_
shown_ ("Open" location is
Twist hem___
stamped on back of transmitter
toopen '_
case.) Insert batteries positive side down°
Weather conditions may cause some minor
changes in door operation requiring some readjustments, particularly during the first year of
operation.
Replace cover as follows. 3-Function remote: Insert
the 3 tabs at the opposite end and snap shut°
Compact 3-Function remote: Snap shut along both
sides.
Pages 28 and 29 refer to the limit and force
adjustments. Only a screwdriver is required. Follow
the instructions carefully°
Dispose of old batteries properly.
Repeat the safety reverse test (page 30) after any
adjustment of limits or force.
,,,,,,,,,,,,,
Maintenance
Once a Month
,
........................
Schedule
Manually operate door. If it is unbalanced or
binding, call for professional garage door service_
Repeat the safety reverse test. Make any
necessary adjustments (See page 30),,
Once a Year
Check to be sure door opens & closes fully.
Adjust limits and/or force if necessary.
(See pages 28 and 29r,)
Oil door rollers, bearings and hinges. The opener
does not require additional lubrication Do not
grease the door tracks.
iiii
31
ii ii ,1111111
......................
Operation of Your Opener
Activate the opener with any of the following:
• The Remote Control: Hold push button down
until the door starts to move.
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible,
use the emergency
release rope and handle only when the door is
fully closed.
= The Door Control: Hold push button down until
the door starts to move.
° The Outdoor Key Switch or Keyless Entry:
(See Accessories)
When the opener is activated with the safety
reversing sensor installed and correctly aligned:
=1
H=,,,
1_ If open, the door will close. If closed, the door will
open,
2. ff closing, the door will reverse,
ase Arm
3o tf opening, the door wilt stop (allowing space for
entry and exit of pets and for fresh air),
4. If the door has been stopped in a partially open
position, it will close°
5. If obstructed while closing, the door wil! reverse.
Emergent]
_._
Relaase Handle _-----'_,,_
(Putt Down}
i
T
6. If obstructed while opening, the door will stop.
Manual disconnect
position
7. The garage door will reverse in the closing cycle
when the invisible beam is broken. If fully open,
the door will not close when the beam is broken.
The sensor has no effect in the opening cycle.
The lockout feature
prevents the trolley from
reconnecting automatically.
Pull the emergency handle
down and back (toward the
opener). The door can then
be raised and lowered
manually as often as
necessary. To disengage
the Lockout Feature, pull
the emergency handle
straight down° The trolley
will reconnect on the next
UP or Down operation°
if the sensor is not installed, or is not aligned
correctly, the door won't close from any remote
transmitter. You can close the door with the Door
Control, the Outdoor Key Switch, or Keytess Entry,
however, if you activate them until down travel is
complete. If you release them too soon, the door will
reverse.
The opener lights will blink for 5 seconds when the
safety reversing sensor causes the door to reverse.
Opener Lights will turn on under the following
conditions: When the opener is initially plugged in;
when the power is interrupted; when the opener is
activated. They will turn off automatically after 4-1/2
minutes or provide constant light when the Light
feature is activated° Bulb size is 75 watts maximum.
To open the door
manually:
The door should be
fully closed if possible.
Pul! down on the red
emergency release
handle and lift the door
manually. To
reconnect the door to
the opener, press the
Door Control push
button..
[,
o"-] Trolley
se Arm
FlalBaseHandle _
(Pull Down & Back
Towards Opener) --
Lockout position
Operation of the Door Controls (seepage18)
Press the lighted push button to open or close the
door.
Press again to reverse the door during the closing
cycle or to stop the door while it's opening.
Premium Console:
Premium Console (cont.):
Lock Feature - The Lock feature is designed to
prevent operation of the door from remote controls.
However, the door will open and close from the Door
Control, the Outdoor Key Switch and the Keyless Entry
Accessories.
Ligl_t Feature- Press the large round Light button_ If
the opener lights are off, they will turn on. If the
opener lights are on, (even in the 4-1/2 minute
automatic cycle) they will turn off..
To Activate: Press and hold the small round Lock
button for 2 seconds. The push button light will flash
as tong as the Lock feature is on.
To turn off: Press and hold the Lock button again
for 2 seconds.The push button light will stop
flashing. The Lock feature wil! also turn off whenever
the "SRT" button on the opener panel is activated.
But if you use the Light button to tum the lights on
and then activate the opener, the lights will tum off
after 4-t/2 minutes.
The Light button will not contro_ the opener lights
when the door is in motion,
32
Receive
and Remote ControR Programming
To cornply v;ilh FCC rules, ad{uS{meni or modi_oa{ions Of i_
andior transmitter are prohibited, except for changing the code setting or 1
replacing the batlery THERE ARE NO OTHER USER SERVICEABLE
I
PARTS
J
Children operating or playing with a garage
door opener can injure themselves or others,
The garage door could close and cause
serious injury or death. Do not allow children
to operate the door push button(s) or remote
control(s).
Models with 3-function remote controls: The
remote controls have been factory set to operate
with the large push button on the remote control.
However, you can use either of the two small
buttons, if you prefer. And, the 3-function remote
control can also activate additional garage door
openers and/or light controls..
A moving
garage door could injure or kill
someone under it. Activate the opener only
when you can see the door clearly, it is free of
obstructions,
and is properly adjusted.
Below are instructions for programming your opener
to match the other buttons on your remote controls
and any additional remote controls you may
purchase. See available accessories on page 38_.
Figure I
53000SRT Series Garage Door Openers
(With "SRT" Button)
Select a remole control push
button !o operate opener
Your "SRT" garage door opener will operate with as
many as four "SRT" portable remote controls and
one Multi-Function Key]ess Entry,
To Add A Remote Control
1, Press and holdthe seiected remote control push
button, see Figure 1..
3-Function
Remote Control
2..Then press and release the "SRT" button on the
right side panel of the opener, Figure 2. The
opener lights will flash once..
3. Release the remote push button.
Now the opener will operate when the remote
control push button is pressed.
Figure 2
Garage Door Opener
If you release the remote control push button
before the opener lights flash, the opener will
not accept the code.
(With "SRT" Button)
©
To Change the Selected Push Button
On the Same Remote control
©
k
If you decide to use a different remote control button
than originally programmed into the opener, you
must erase all the learned codes and reprogram
each remote control used to operate the garage
door opener..
To Erase All Remote control Codes
- Press and hold the "8RT" button on the opener
panel until the indicator light turns off (about 6
seconds). A//the codes the opener has learned
will be erased.
"SRT"
Butlon
Indicator
Ugh!
=To reprogram, repeat Steps 1,2 and 3 for each
remote control in use..
END PANEL
Code programming instructions
on the opener panel.
are also located
33
Having a ProbUem?
Situation
Probable
Cause and Solution
The opener doesn't
operate from either
the Door Control or
the remote control:
1. Does the opener have electric power?. Plug a lamp into the outlet. If it doesn't light,
check the fuse box or the circuit breaker. (Some outlets are controlled by a door switch.)
2. Have you disabled all door locks? Review instaltation instruction wamings on Page 11.
& Is there a build-up of ice or snow under the door? The door may be frozen to the
ground° Remove any restriction,.
4o The garage door spring may be broken° Have it replaced°
5o Repeated operation may have tripped the overload protector in the motor. Wait
15 minutes. Try again.
Opener operates
from the remote
control, but not from
the Door Control:
I. Is the Door Control lit? if not, remove the bell wire from the opener terminal screws.
Short the red and white terminals by touching both terminals at the same time with a
piece of wire. If the opener runs, check for a faulty wire connection at the Door
Control, a short under the staples, or a broken wire._
2. Are the wiring connections correct? Review Step 6, page 18.
i
,m
i,
,n
, ,,n,n,,,,=-,,=......
="'"u"
The door operates
from the Door
Control, but not from
1. If your model has the Lock feature, make sure the lock is Off.
2o Is any door push button flashing? Your opener needs to re-learn a remote control
code. Refer to Instructions on the opener panel.
the remote control:
3. Program the receiver to match the remote control code.
4o Repeat the receiver programming procedure with all remote controls,
.....
= =,=,,n,
The remote control
has short range:
=='''"'""n'="nHH'
="
!. Change the location of the remote controt in your car°
2, Check to be sure the antenna on the side or back panel of opener extends fully
downward°
3. Some installations may have shorter range due to a metal door, foil backed
insulation, or metal garage siding.
Opener noise is
disturbing in living
quarters of home:
If operational noise is a problem because of proximity of the opener to the living
quarters, the Vibration Isolator Kit 4tA3263 can be installed° This kit was designed to
minimize vibration to the house and is easy to install,
The garage door
opens and closes
by itself:
1. Be sure that all remote control push buttons are off,
2. Remove the bell wire from the Door Control terminals and operate from the remote
control only if this solves the problem, the Door Control is faulty (replace), or there is
an intermittent short on the wire between the Door Control and the opener,
, =,=,,,,,=......................
i1,=,,,
The door doesn't
open completely:
1. tf the door has been working properly but now doesn't open all the way, increase the
up force See page 29.
2. ts something obstructing the door?. Remove the obstruction or repair the door.
3,, If door opens at least 5 feet, the travel limits may need to be increased° One turn
equals 2 inches of travel. See page 28.
Repeat the safety reverse test after the adjustment
i
,=, =,,u,
,'
The door stops but
doesn°t close
completely:
is complete.
" ,i i= ,,=,,,=
Review the travel limits adjustment procedures on page 28,
Repeat the safety reverse test after any adjustment of door arm length, close
force or down limiL
34
Having a Probaem? (continued)
Situation
Probable
Cause & Solution
The door opens but
won't close:
1. If the opener lights blink, check the safety reversing sensor., See page 23.
...........
M,,
' "1I'"'_
.....
"
I'1'11'11
....
I'_
....
2.. If the opener lights do not blink and it is a new installation, check the down force°
See Adjustment Step 2, page 29. For an existing installation, see below.
Repeat the safety reverse test after the adjustment
,,,i, ,,,i,i....
The door reverses for
no apparent reason
and opener lights
don't blink:
' ........
is complete.
, ,,,,i ...............
1o Is something obstructing the door? Pull the red emergency release handle, Operate
the door manually° If it is unbalanced or binding, call for professional garage door
service.
2o Clear any ice or snow from the garage floor area where the door closes.
3. Review the force adjustment procedures on page 29°
4. If door reverses in the fully closed position decrease the travel limits (page 28)°
Repeat safety reverse test after adjustments to force or travel limits. The need
for occasional adjustment of the force and limit settings is normal Weather
conditions in particular can affect door travel
i
...... i,,,.,_,_,
.......
The door reverses for
no apparent reason
and opener lights
blink for 5 seconds
after reversing:
i
ii, , ,,i,,,llr
i,,11
.......
i, i.......
, ,,i
Check the safety reversing sensor. Remove any obstruction or align the receiving eye°
See page 23.
i ...........
i
The opener lights:
,i,11,
,
, ,,,,,11,,,,,,,i
..........
_'_"
•.. don't turn on:
Replace the light bulbs (75 watts maximum), Use a standard neck garage door opener
bulb if regular bulb burns out°
•.. don't turn off:
ts the Light feature on? Turn it off.
i,
,,
The door may be out of balance or the springs are broken. Close the door and use the
emergency release to disconnect the trolley, Open and close the door manually. A propedy
balanced door will stay in any point of travel while being supported entirely by its springs. If it
does not, disconnect the opener and call a professional garage door serviceman. Do not
increase the force to operate the opener.
The opener strains or
maximum force is
needed to operate
door:
.,
,
i,
i
..... iii,
1. The garage door springs are broken_ See above.
2. If the problem occurs on the f_rstoperation of the opener, door may be locked. Disable
the door lock. If the belt was removed and reinstalled, the motor may be out of phase.
Remove the belt; cycle the motor to the down position.. Observe the drive sprocket.
When itturns in a clockwise direction and stops in the down position, reinstall the belt.
The opener motor
hums briefly, then
won't work:
Repeat the safety reverse test after the adjustment
,
,
The opener won't
operate due to
power failure:
,
is complete.
ii1,,i,
1. Use the emergency release to disconnect the trolley_The door can be opened and closed
manually. When the power is restored, press the Door Control push button and troIley will
automatically reconnect (unless troIley is in lockout position.) See page 32.
2. The Emergency Key Release accessory (for use on garages with no service door)
disconnects the trolley from outside the garage in case of power failure.
35
Repair Parts
Rail Assembly
3
Parts
=,1=,,=
KEY
NO.
PART
NO.
4
i =
DESCRIPTION
,, ,i,i1,,11,,i,
1
2
3
4
5
6
7
8
9
1A995
41B3869-1
1B3117
183Bl10
41A35B8
41A3589-3
83A4
41 B4103
109B33
41A3534
i ,
....
=
i
Master link kit
Complete trolley assembly
T-rail - center section
T-rail - end section
Belt pulley bracket
Full belt assembly
Rail grease
Tension assembly (Spring/Trolley Nut)
Trolley Clip
NOT SHOWN
Rail assembly hardware kit (includes
hardware illustrated on page 7).
F
i
Installation
Parts
_6
4
K'I=Y PART
NO.
NO.
DESCRIPTION
iii
1
2
41A4884
41A4873
3
4
5
6
7
8
9
I0
11
10A19
29Bt34
4"1A2828
41A4353
217A238
12B380
178B35
12B374
41A4373A
13
14
15
16
12B483
12B484
12B485
12B350
178B34
41A4437-1
41A4116
114A1983
7
iii
Premium control console
3-function remote control housing
(no circuit board)
3V 2016 Uthium battery (2 required)
Visor clip for Part No. 41A4873
Emergency rope & handle assembly
Header bracket w/clevis pin & fastener
2-conductor bell wire - white & whitelred
Door bracket plate
Curved door arm section
Door bracket
Safety sensor kit (receiving and sending eyes)
with 3' 2*conductor bell wire attached
=C"Wrap Bracket
Square Hole Bracket
Slotted Bracket
Hanging brackets
Straight door arm section
NOT SHOWN
Installation hardware bag (includes hardware
illustrated on page "f),
Safety sensor hardware
Owner's manual
36
11
10
15
\
12
13
16--
Repair Parts
,,
....
,,,
Opener Assembly
,i
......
i,,,
Parts
20-
15
13
\/
5
17
.................
14
(Down)
Brown
Contact
UMIT SWITCH ASSY,
Drive_
Center Limit
Contact
(Up)
Contact
,, i ..........
KEY
NO.
PART
NO.
1
2
41 A4371
4t A4885
KEY
NO.
DESCRIPTION
9
Belt cap retainer
PART
NO.
DESCRIPTION
L'_dJ Yei!ow
Wire
,....
108D46
Lens
t0
30B363
Capacitor - 1/2HP
1t
12
t2A373
41 D3150
Capacitor bracket
Terminal biock w/screws
13
41C4842
Universal replacement motor &
bracket assembly
Complete with: Motor, worm,
bracket, bearing assembly,
RPM sensor
14
41 R396-1
Cover
15
16
41A2818
41 D3452
Helical gear & retainer w/grease
Limit switch assembly
4
41 B4245
Gear and sprocket assembly
Complete with:
Spring washer
Thrust washer
Retaining ring
Beadng plate
Roll pins (2)
Drive gear and worm gear
Helical gear w/retainer and grease
Drive/worm gear kit w/grease
Roll pins (2)
Line cord
5
41 CA876
Wire harness assembly w/plug
17
41C4398A
RPM sensor assembly
Receiver logic board assembly
Complete with:
Logic board
End panel w/all labels
18
19
41A2826
41A2822A
Shaft bearing kit
Interrupter cup assembly
20
41A4923
End panel
NOT SHOWN
Opener assembly hardware kit
(includes screws not designated by
a number in illustration).
41 A2817
6
41 A4315-6C
7
8
4IA4924
175B88M
41A2825
Light socket
37
Accessories
,,,,,,,,,
,,,
..............
,
,,
,i.................i,
,,,,
:
_
Sears offers many useful accessories for your garage door opener. They are illustrated below with
Sears model numbers and descriptions.
........
139.53702
I I
Emergency Key Release:
f
_*ii.
I ..........
I
139.53879
i
I I
IIIIII=III
i ........
III
3-Function Remote Control:
Includes visor clipo
Required for a garage with NO
access door. Enables homeowner
i to open garage door manually from
outside by disengaging trolley.
.......... i,i .......
139.53703
Outdoor Key Switch:
139.53859
Operates the garage door
automatically from outside when
remote control is not handy.
With loop for attaching key ring.
i,,,i.......
..... i, ,,i,=,,
8 Foot Rail Extension
139.53_04
Compact 3-Function
Remote Control:
t39.53876
Multi-Function
,.................... '.....
Keyless Entry:
Enables homeowner to operate
garage door opener from outside
by entering a 4 digit code on
specially designed keypad.
To allow an 8 foot door to open flJlty.
............ ,.,,,........
139.5 05
10 Foot Rail Extension:
139.53774
Plug-in Light Control:
Enables homeowner to turn on a
lamp, television or other appliance
from car, bedside, or anywhere in
the home with a remote.
139.53773
Wire-in Light Control:
To allow a t0 foot door toopen fully.
.,,,,
53885
Support Brackets:
For finished ceilings or where
additional support is required,
based on garage construction.
Includes brackets and fastening
hardware.
..... ,i,,,
13933709
@
Wires into light switch box to enable
homeowner to control outside or
inside lights with remote. (Can also
be operated manually.)
i
Door Clearance Brackets:
(For Sectional Doors Only)
Replaces top brackets and rollers on door to reduce height of door travel For use when
installing opener in garage with low headroom clearance°
ii1,,i,
i1,11,
38
index
Manual (Emergency) Release Rope & Handle
Lockout feature .................................................................................................................................................................................
32
Manual disconnect .........................................................................................................................................................................
32
Safety warnings ......................................................................................................................................................
11, 19, 31, 32
Opener Terminals
Door contro_ connections ...........................................................................................................................................................
18
Safety reversing sensor connections ..................................................:............................................................................. 23
Outdoor key switch accessory connections ..........................................................................................................................
18
Safety Reverse Test Procedure ...................................................................................................................................... 30
Testing required ........................................................................................................................................... 11, 30, 34, 35
Safety reverse system problems
Secudng header bracket to wall .................................................................................................................................... 12
Adjusting travel limits ..............................................................................................................................................
28
Applying excessive force on the door .....................................................................................................................
29
Buckling or uneven floor .....................................................................................................................................
4, 5
Safety Warnings ............................................................ 2, 3, 9, 11, 12, 16, 18, 19, 20, 21, 24, 28, 29, 30, 31, 32, 33
User Instruction Label for garage wall ...........................................................................................................
39
11, 18
For the repair or replacement parts you need
Call 7 am - 7 pm, 7 days a week
t -8OO=366=PART
Model No.
139.53800SRT
(1-800-366-7278)
For in-home major brand repair service
Call 24 hours a day, 7 days a week
1 -SOO-4=REPAIR
(1-800-473-7247)
For the location of a
Sears Repair Service Center in your area
Ca}l 24 hours a day, 7 days a week
t =8OO=488=1222
The model number
label is located under
For information on purchasing a Sears
Maintenance Agreement or to inquire
about an existing Agreement
Call 9 am - 5 pro, Monday-Saturday
t =S00=827=6655
the light lens on the
left side panel of your
America's
Repair Specialists
opener.
SEARS WARRANTY
When requesting
service or ordering
parts, always provide
the following
information:
FULL 90-DAY WARRANTY
ON GARAGE DOOR OPENER
For 90 days from the date of purchase, Sears wiII repair this Garage Door Opener,
free of charge, if defective in material or workmanship,,
LIMITED WARRANTY
From the 9let day until one year from the date of purchase, Sears wiil furnish
replacement parts for any defective parts, free of charge You pay for labor.
LIMITED WARRANTY
ON MOTOR
After t year and through 5 years, if the motor on this Garage Door Opener is
defective, Sears wiil furnish replacement motor, free of charge You pay for labor_
LIMITAI"tON ON LIABILITY
® Product Type
•, Model Number
,. Part Number
SEARS WILL NOT BE LIABLE FOR LOSS OR DAMAGE TO PROPERTY OR ANY
INCIDENTAL OR CONSEQUENTIAL LOSS OR EXPENSE FROM PROPERTY
DAMAGE DUE DIRECTLY OR INDIRECTLY FROM THE USE OFTHIS
PRODUCT. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you,
,, Part Description
This warranty does not cover light bulbs or repair parts necessary because of
operator abuse or negligence, including the failure to instal, adjust and operate this
garage door opener according to instructions contained in the owner's manual.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING
SEARS CENTER/DEPARTMENT
IN THE UNITED STATES.
THE NEAREST
This warranty applies only whi_ethis product is in use in the United States.
This warranty gives you specific iegal rights, and you may a}so have other rights
which vary from state to state.
SEARS, ROEBUCK AND CO., DepL 817WA, Hoffmen Estates,
114A1983,,,
Sears, Roebuck and Co,, Hoffman Estates, IL 60179 USoA=
©1995, All Rights Reserved
IL 60179
Printed in Mexico