Electrolux EFP 60310 User manual

User manual
EFP 60310
EFP 60520
electrolux
3
Welcome to the world of Electr
olux
Electrolux
Thank you for choosing a first class
product from Electrolux, which
hopefully will provide you with lots of
pleasure in the future. The Electrolux
ambition is to offer a wide variety of
quality products that make your life
more comfortable. You find some
examples on the cover in this manual.
Please take a few minutes to study this
manual so that you can take advantage
of the benefits of your new machine.
We promise that it will provide a
superior user experience delivering
ease of mind.
Good luck!
GB
4
electr
olux contents
electrolux
Contents
Safety warnings ..............................
Description of the Appliance ...........
Control Panel .................................
Maintenance and Care ...................
Special accessories ........................
Something Not Working .................
Installation ......................................
GB
57
59
60
62
66
66
67
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips.
Environmental information.
electrolux safety warnings
5
Safety warnings
• Any installation work must be undertaken by a qualified electrician or a
competent person.
• This hood must be installed in
accordance with the installation
instructions and all measurements
must be adhered to.
• When used as an extractor unit, the
hood must be fitted with a hose
having preferably the same diameter
as the outlet hole.
Attention: The hose is not supplied
and must be pur
chased separately
purchased
separately..
• The minimum distance between the
supporting surface for the cooking
vessels on the hob and the lowest
part of the range hood must be not
less than 65cm from electric cookers
and from gas or mixed cookers.
If the instructions for installation for
the gas hob specify a greater distance, this must be adhered to.
• Before any cleaning or maintenance
operation, disconnect hood from the
mains by removing the plug or
disconnecting the mains electrical
supply.
Always wear work gloves for all
installation and maintenance operations.
• The appliance is not intended for use
by children or persons with impaired
physical, sensorial or mental faculties,
or if lacking in experience or knowledge, unless they are under supervision or have been trained in the use
•
•
•
•
•
•
•
•
•
•
•
of the appliance by a person responsible for their safety.
This appliance is designed to be
operated by adults, children should
be monitored to ensure that they do
not play with the appliance.
This appliance is designed to be
operated by adults. Children should
not be allowed to tamper with the
controls or play with the appliance.
Never use the hood without effectively mounted grating!
The hood must NEVER be used as a
support surface unless specifically
indicated.
The premises where the appliance is
installed must be sufficiently ventilated, when the kitchen hood is used
together with other gas combustion
devices or other fuels.
The ducting system for this appliance
must not be connected to any
existing ventilation system which is
being used for any other purpose
such as discharging exhaust fumes
from appliances burning gas or other
fuels.
The flaming of foods beneath the
hood itself is severely prohibited.
The use of exposed flames is detrimental to the filters and may cause a
fire risk, and must therefore be
avoided in all circumstances.
Any frying must be done with care in
order to make sure that the oil does
not overheat and ignite.
Accessible parts may become hot
when used with cooking appliances.
With regards to the technical and
GB
6
•
•
•
•
GB
electr
olux safety warnings
electrolux
safety measures to be adopted for
fume discharging it is important to
closely follow the regulations provided by the authorised authorities.
The hood must be regularly cleaned
on both the inside and outside (AT
LEAST ONCE A MONTH).
This must be completed in accordance with the maintenance instructions provided in this manual). Failure
to follow the instructions provided in
this user guide regarding the cleaning
of the hood and filters will lead to the
risk of fires.
Do not use or leave the hood without
the lamp correctly mounted due to
the possible risk of electric shocks.
We will not accept any responsibility
for any faults, damage or fires caused
to the appliance as a result of the
non-observance of the instructions
included in this manual.
This appliance is marked according to
the European directive 2002/96/EC on
Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate
waste handling of this product.
The symbol
on the product, or on
the documents accompanying the
product, indicates that this appliance
may not be treated as household
waste. Instead it should be taken to the
appropriate collection point for the
recycling of electrical and electronic
equipment.
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about
treatment, recovery and recycling of
this product, please contact your local
authority.
electrolux description of the appliance
7
Description of the Appliance
• The cooker hood is designed to
extract unpleasant odours fr
om the
from
kitchen, it will not extract steam.
• The hood is supplied as an extractor
unit and can also be used with a
recirculation mode by fitting a charcoal filter.
• You will need an original charcoal
filter for the recirculation mode. (See
Special Accessories).
Extraction mode
• In this mode fumes are extracted to
the outside via a hose connected to
the coupling ring
ring.
• In order to obtain the best performance the hose should have a diameter equal to the outlet hole.
Extraction mode
Recir
culation mode
Recirculation
coal
• The air is filtered through a char
charcoal
filter and returned to the kitchen.
• You will need an original charcoal
filter for the recirculation mode. (See
Special Accessories).
GB
Recir
culation mode
Recirculation
8
electr
olux control panel
electrolux
Control Panel
• Best results are obtained by using a
low speed for normal conditions and
a high speed when odours are more
concentrated.
Turn the hood on a few minutes
before you start cooking.
The hood should be left on after
cooking for about 15 minutes or until
all the odours have disappeared.
• The controls are positioned near the
lights:
• the light switch switches the hood
lamp on and off
• the motor switch switches the motor
on and off, enabling you to select one
of the three different speeds.
The pull-out tray must be opened for
cooker hood operation (suction) to
begin.
Opening the pull-out tray
• Pull the tray downwards.
• Slide it out until it reaches its stop
limit.
GB
Light switch
Motor switch
sklok!
electrolux maintenance and care
9
Maintenance and Care
• Befor
e performing any maintenance operation, isolate the hood fr
om the
Before
from
electrical supply by switching of
emoving the connector
offf at the connector and rremoving
fuse.
Or if the appliance has been connected thr
ough a plug and socket, then the
through
plug must be rremoved
emoved fr
om the socket.
from
Metal gr
ease filter
grease
• The purpose of the grease filters is to
absorb grease particles which form
during cooking and it must always be
used, either in the external extraction
or internal re-circulation function.
Attention: the metal grease filters
must be removed and washed, either
by hand or in the dishwasher, every
four weeks.
Removing the metal gr
ease filter
grease
• Use the spring handle and remove
the filter downward.
Hand washing
Soak grease filters for about one hour
in hot water with a grease-loosening
cleaner, then rinse off thoroughly with
hot water. Repeat the process if
necessary. Refit the grease filters
when they are dry.
Dishwasher
Place grease filters in the dishwasher.
Select most powerful washing
programme and highest temperature,
at least 65°C. Repeat the process.
Refit the grease filters when they are
dry.
When washing the metal grease filter
in the dishwasher a slight
discolouration of the filter can occur,
this does not have any impact on its
performance.
• Never use corrosive, abrasive or
flammable cleaning products or
products containing bleach.
GB
10
electr
olux maintenance and care
electrolux
Char
coal filter
Charcoal
• The charcoal filter should only be
used if you want to use the hood in
recirculation mode.
• To do this you will need an original
charcoal filter (available from your
local Service Force Centre).
coal filter
• Replacing the char
charcoal
The charcoal filter cannot be washed
nor regenerated.
The charcoal filter should be replaced
every 4 months under normal use.
Replacement filters are available from
your local Service Force Centre.
• Fitting
Pull out the drawer (see paragraph
“Contr
ol Panel - Opening the pull-out
Control
tray
”)
tray”)
”), remove the grease filter (see
paragraph “Maintenance and Care ”)
Metal grease filter”)
”).
Fit the charcoal filter so that it covers
the grilles protecting the hood motor
and fan, turn the carbon filter handle
in a clockwise direction.
Note: T
wo char
coal filters ar
e
Two
charcoal
are
requir
ed for cooker hoods with two
equired
motors and one char
coal filter for
charcoal
cooker hoods with one motor
motor..
Refit the grease filters.
emove proceed in the reverse
• To rremove
order.
GB
• Always specify the hood model
number, serial number and product
number code when ordering replacement filters. This information is shown
on the rating plate located on the
inside of the unit.
• The charcoal filter can be ordered
from your local Service Force Centre.
electrolux maintenance and care
11
War
ning
arning
• Failure to observe the instructions on
cleaning the unit and changing the
filters will cause a fire hazard. You are
therefore strongly recommended to
follow these instructions.
• The manufacturer declines all responsibility for any damage to the motor
or any fire damage linked to inappropriate maintenance or failure to
observe the above safety recommendations.
Changing the light bulb(s)
om
• Disconnect the cooker hood fr
from
the mains supply
supply..
• Prior to touching the light bulbs
ensur
e they have cooled down.
ensure
• Press and release the light cover to
open.
• Replace the damaged light bulb.
Only use max. 20W halogen light
bulbs (G4-12V), and make sure you
do not touch them with your bare
hands.
• Close the light cover (push-fit) again.
In case of accidental opening of the
light cover, it should first be opened
completely before closing.
• If the light does not come on, make
sure the bulb has been inserted in
correctly before contacting your local
Service Force Centre.
1
20W max G4
2
3 CLICK!
GB
12
electr
olux maintenance and care
electrolux
Cleaning the hood
• Clean the outside of the hood using a
damp cloth and a solution of water
and mild washing up liquid.
• Never use corrosive, abrasive or
flammable cleaning products or
products containing bleach.
• Never insert pointed objects in the
motor’s protective grid.
• Only ever clean the switch panel and
filter grill using a damp cloth and mild
washing up liquid.
• Clean all the plastic parts with a soft
cloth soaked in warm water and
neutral soap.
• It is extremely important to clean the
unit and change the filters at the
recommended intervals. Failure to do
so will cause grease deposits to build
up that could constitute a fire hazard.
GB
electrolux special accessories
13
Special accessories
Char
coal filter Type 303
Charcoal
Model EFP 60520 :
2 charcoal filters are necessary
Something Not Working
If your appliance fails to work properly please carry out the following checks.
Symptom
Solution
The cooker hood will not start...
Check that: The hood is connected
to the electricity supply.
Check that a fan speed has been
selected.
The cooker hood is not working
Check that: The fan speed is set high
enough for the task.
The grease filters are clean.
The kitchen is adequately vented to
allow the entry of fresh air.
If set up for recirculation, check that
the charcoal filter is still effective.
If set up for extraction, check that the
ducting and outlets are not blocked.
The cooker hood has switched off
during operation...
The safety cut-out device has been
tripped. Turn off the hob and then
wait for the device to reset. If the
hood has been installed below the
heights indicated in the installation
instructions the motor will cut-out
frequently which will damage the
hood.
If after all these checks, the problem persists, contact your local Service Centre,
quoting the model number, serial number and product number code.
Please note that it will be necessary to provide proof of purchase for any inguarantee service calls.
In-guarantee customers should ensure that the above checks have been made as
the engineer will make a charge if the fault is not a mechanical or electrical breakdown.
GB
14
electr
olux installation
electrolux
Installation
Technical Details
EFP 60310
EFP 60520
Height:
20,8
20,8
Height (with opened drawer)
24
24
Width:
55,8
55,8
Depth:
27,6
27,6
Max. absorb. power:
165 W
290 W
Motor:
125 W
2 x 125 W
Lighting:
2 x 20 W (12V-G4)
2 x 20 W (12V-G4)
Length of the cable:
150 cm
150 cm
Electrical connection:
220-230 V
220-230 V
Fuse rating:
5At
5At
Dimensions (in cm):
Mounting accessories included
1 coupling ring
4 brackets
2 screwdriver inserts (to tighten torx screws)
1 spacer
1 Aesthetic cover
2 screws 4 x 8 mm
GB
4 screws 4,5 x 16
3 screws 3,5 x 9,5
2 screws 3 x 9
electrolux installation
15
Electrical connection
Safety war
nings for the electrician
warnings
The mains power supply must correspond to the rating indicated on the
plate situated inside the hood. If
provided with a plug connect the hood
to a socket in compliance with current
regulations and positioned in an
accessible area. If it not fitted with a
plug (direct mains connection) or if the
plug is not located in an accessible
area apply a double pole switch in
accordance with standards which
assures the complete disconnection of
the mains under conditions relating to
over-current category III, in accordance
with installation instructions.
War
ning! Before re-connecting the
arning!
hood circuit to the mains supply and
checking the efficient function, always
check that the mains cable is correctly
assembled.
GB
16
electr
olux installation
electrolux
Installation
War
ning! Do not connect the appliance to the mains until the installation is fully
arning!
complete.
Pr
eparing the cabinet
Preparing
Ø 130mm
Ø 130mm
189mm
Ø 130mm
min. 200mm
189mm
Ø 130mm
min. 276
max. 325
GB
First, check the dimensions given in the
diagrams to make sure the cabinet is
suitable for the cooker hood.
Make the holes required for the power
supply cable and the exhaust hose.
Make the same type of holes in the top
of the cabinet.
min. 200mm
min. 276
max. 325
The cooker hood may be installed in a
wider cabinet if the special Installation
KIT is used (see "Special accessories"
chapter).
Contact your nearest Authorised
Assistance Centre to confirm the
necessary details.
electrolux installation
Fixing the brackets to the cabinet
• Apply the template to the inner righthand side of the cabinet.
• The lower edge at the front of the
template should be aligned with the
lower edge at the front of the cabinet
(without taking any doors into
account).
• Mark the two fixing points.
• Fix bracket R to the cabinet using 2
screws.
Note! To achieve the correct position,
fasten the screws through the
smallest holes in the bracket.
R
200
17
69,1
46
Ø 4,5 x 16
• Repeat this procedure on the inner
left-hand side of the cabinet (Bracket
L).
69,1
46
200
GB
Ø 4,5 x 16
18
electr
olux installation
electrolux
Before installing the hood
• When using cabinets with a greater
depth measurement than the cooker
hood, a spacer may be installed.
• The spacer can compensate for
differences in depth measurement of
up to 5 cm.
• Measure the difference between the
cabinet depth and the hood depth
(see chapter "Technical details") and
use a cutter to remove any excess.
• Fix the spacer to the back of the
hood using 3 snap-fastening clips.
max 5cm
Ø 3,5 x 9,5
GB
electrolux installation
Fitting the hood inside the cabinet
• Position the hood inside the cabinet,
by sliding its brackets over the
brackets fixed to the cabinet until the
stop limit is reached.
• Run the power supply cable through
the special slots in the cabinet.
• Secure the hood, using 2 screws
(one per side) to fix the brackets
together.
• If the hood is not perfectly in line with
the lower edge of the cabinets at the
side, its position can be adjusted by
means of the internal fixing screws
Fixing the brackets to
(see chapter "Fixing
the cooker hood"
hood on the previous
page).
• Fit the connection flange to the
exhaust hose, which should have a
suitable length and diameter for
channelling fumes outside (Ducted
version), or to the top of the cabinet
(Filter version).
• Fix the connection flange to the
exhaust outlet of the hood (snapfastening).
When fastened correctly, the
indicator on the flange should be
aligned with the corresponding notch
in the exhaust outlet.
• Complete the connection at the other
end of the exhaust hose.
• Filter version only: Fit the charcoal
Maintenance
filter(s) (see chapter "Maintenance
and Car
e
Char
coal
Care Charcoal filter
filter").
• Fit the grease filter(s) (see chapter
Maintenance and Car
e - Metal
"Maintenance
Care
gr
ease
filter
grease filter").
• Connect the hood to the electricity
supply.
19
2x Ø 4 x 8
GB
20
electr
olux installation
electrolux
Adjusting the cooker hood
The position of the cooker hood may
be adjusted.
Once the installation procedure is
complete, you will find it useful to
perform small adjustments with regard
to the position of the hood inside the
cabinet.
• Open the pull-out tray (see chapter
Contr
ol Panel - Opening the pull-out
"Contr
Control
tray
tray").
• Remove the grease filter (see chapter
Maintenance and Car
e - Metal
"Maintenance
Care
gr
ease
filter
grease
").
Y
• Loosen BUT DO NOT COMPLETEL
COMPLETELY
REMOVE the internal screws fixing
the right and left-hand adjustment
brackets in place.
• Adjust the position of the hood and
re-tighten the screws.
GB
Ø4x8
electrolux installation
21
Installing the buffer strip
Apply the buffer strip above the cooker
hood and fix it in place using 2 screws,
working from inside the hood.
Ø3x9
GB
LIB0006370 Ed. 11/09