KEEX-6100
Industrial ECX Embedded SBC with 2nd generation
Intel® core i3/i5/i7 processor
User’s Guide
KEEX-6100 User’s Manual
I
Contact Info:
Quanmax Inc.
4F, No. 415, Ti-Ding Blvd. Sec. 2NeiHu District,
Taipei 114Taiwan
Tel: +886-2-2799-2789
Fax: +886-2-2799-7399
Visit our site at:
www.quanmax.com
© 2011 Quanmax Inc. All rights reserved.
The information in this user’s guide is provided for reference only. Quanmax does not assume any
liability arising out of the application or use of the information or products described herein. This user’s
guide may contain or reference information and products protected by copyrights or patents and does
not convey any license under the patent rights of Quanmax, nor the rights of others.
Quanmax is a registered trademark of Quanmax. All trademarks, registered trademarks, and trade
names used in this user’s guide are the property of their respective owners. All rights reserved. This
user’s guide contains information proprietary to Quanmax. Customers may reprint and use this user’s
guide in other publications. Customers may alter this user’s guide and publish it only after they remove
the Quanmax name, cover, and logo.
Quanmax reserves the right to make changes without notice in product or component design as
warranted by evolution in user needs or progress in engineering or manufacturing technology.
Changes which affect the operation of the unit will be documented in the next revision of this user’s
guide.
KEEX-6100 User’s Manual
II
Content
Content
Content....................................................................................................................... 3
Figures ....................................................................................................................... 5
Tables ......................................................................................................................... 6
Safety Instructions ...................................................................................................... 8
Before You Begin ......................................................................................... 8
When Working Inside a Computer ............................................................... 8
Preventing Electrostatic Discharge .............................................................. 9
Preface ..................................................................................................................... 11
How to Use This Guide .............................................................................. 11
Unpacking.................................................................................................. 11
Regulatory Compliance Statements .......................................................... 11
Warranty Policy ......................................................................................... 12
Maintaining Your Computer ....................................................................... 13
Chapter 1 Introduction ........................................................................................... 16
Overview ................................................................................................... 16
Product Specifications ............................................................................... 17
System Block Diagram .............................................................................. 19
Mechanical Dimensions ............................................................................. 20
Chapter 2 Hardware Settings ................................................................................ 22
Overview ................................................................................................... 22
Jumper Settings and Pin Definitions .......................................................... 23
Jumper Settings ...................................................................................... 24
Rear Panel Pin Assignments ................................................................... 26
Main Board Pin Assignments................................................................... 28
Chapter 3 System Installation ................................................................................ 37
Expansion Interfaces ................................................................................. 37
Memory Module Installation ....................................................................... 37
Chapter 4 AMI BIOS Setup.................................................................................... 39
Overview ................................................................................................... 39
Main Menu ................................................................................................. 40
Advanced Menu......................................................................................... 41
Boot Menu ................................................................................................. 52
Security Menu............................................................................................ 53
Save & Exit Menu ...................................................................................... 53
KEEX-6100 User’s Manual
3
Content
Chapter 5
Driver Installation................................................................................. 55
Appendix A DIO (Digital I/O) Sample Code ............................................................ 56
Appendix B WatchDog Timer Sample Code .......................................................... 58
KEEX-6100 User’s Manual
4
Figures
Figures
Figure 1 Block Diagram ............................................................................. 19
Figure 2 Mechanical Dimensions ............................................................... 21
Figure 3 Jumper Connector ....................................................................... 22
Figure 4 Jumper and Connector Locations ................................................ 23
Figure 5 Rear Panel IO .............................................................................. 26
Figure 6 Align the SO-DIMM Memory Module with the onboard socket ..... 37
Figure 7 Press down on the SO-DIMM Memory Module to lock it in place 38
KEEX-6100 User’s Manual
5
Tables
Tables
Table 1 KEEX-6100 Specification............................................................... 18
Table 2 Jumper List .................................................................................... 24
Table 3 JP1 ME F/W Selection................................................................... 24
Table 4 JP2 Panel & Backlight Power Selection for LVDS2 ....................... 24
Table 5 JP3 Panel Backlight Power Selection for LVDS1........................... 25
Table 6 JP4 Backlight Power Enable Selection for LVDS1 ........................ 25
Table 7 JP5 Backlight Power Enable Selection for LVDS2......................... 25
Table 8 JP6 AT/ATX Mode Selection .......................................................... 25
Table 9 JP7 SRTC Reset Selection ........................................................... 25
Table 10 JP8 RTC Reset Selection ............................................................ 25
Table 11 Rear Panel Connector List........................................................... 26
Table 12 CN9 LAN1 & USB 2.0 Port 0, 1 Connector.................................. 26
Table 13 CN10 LAN2 & USB 2.0 Port 8, 9 Connector................................ 26
Table 14 DP1 Display Port Connector........................................................ 27
Table 15 HDMI1 HDMI Connector.............................................................. 27
Table 16 VGA1 DB-15 VGA Connector ...................................................... 27
Table 17 Internal Connector List ................................................................ 28
Table 18 ATX2 +12V Power Input Connector ............................................. 28
Table 19 CR2032 Battery Power Input Wafer ............................................ 28
Table 20 CFD1 CF Type II Connector ........................................................ 29
Table 21 COM1 RS-232/422/485 Port 1 Wafer .......................................... 30
Table 22 COM2 RS-232 Port 2 Wafer ........................................................ 30
Table 23 CN1 Digital Input / Output Pin Header ......................................... 30
Table 24 CN2 SATA HDD Power Output Wafer.......................................... 30
Table 25 CN3 Backlight Power Output Wafer for LVDS1 ........................... 31
Table 26 CN4 SIM Interface Wafer for MPCIE1 ......................................... 31
Table 27 CN5 USB 2.0 Port 2, 3 Pin Header.............................................. 31
Table 28 CN6 USB 2.0 Port 10, 11 Pin Header .......................................... 31
Table 29 CN7 S/PDIF Pin Header .............................................................. 32
Table 30 CN8 Audio Pin Header ................................................................ 32
Table 31 CN12 Left Channel 2W Audio AMP Output Wafer ....................... 32
Table 32 CN13 Right Channel 2W Audio AMP Output Wafer ..................... 32
Table 33 CN14 Backlight Power Output Wafer for LVDS2 ......................... 32
Table 34 CN20 Keyboard & Mouse Wafer ................................................. 33
KEEX-6100 User’s Manual
6
Tables
Table 35 DIMM1 DDR3 Memory SO-DIMM Socket ................................... 33
Table 36 FAN1 CPU FAN Wafer................................................................. 33
Table 37 FP1 Front Panel 1 Pin Header .................................................... 33
Table 38 FP2 Front Panel 2 Pin Header .................................................... 33
Table 39 IR1 IrDA Pin Header .................................................................... 33
Table 40 LVDS1 Primary 24-bit, 2-channel LVDS Panel Connector ........... 34
Table 41 LVDS2 Secondary 24-bit, 2-channel LVDS Panel Connector ...... 34
Table 42 MPCIE1 Mini-PCIE Express v 1.2 Socket ................................... 35
Table 43 SATA1 Serial ATA Port 0 Connector ............................................ 36
Table 44 SATA2 Serial ATA Port 1 Connector ............................................ 36
Table 45 BIOS Main Menu ......................................................................... 40
Table 46 Advanced Menu ........................................................................... 41
Table 47 Advanced Menu – Display Configuration ..................................... 42
Table 48 Advanced Menu – Super IO Configuration.................................. 43
Table 49 Advanced Menu – Super IO Configuration – Serial Port 1
Configuration ............................................................................... 44
Table 50 Advanced Menu – Super IO Configuration – Serial Port 2
Configuration ............................................................................... 44
Table 51 Advanced Menu –Power Management Configuration.................. 45
Table 52 Advanced Menu –CPU Advanced Configuration ......................... 46
Table 53 Advanced Menu –Trusted Computing ......................................... 47
Table 54 Advanced Menu –SATA Configuration ......................................... 47
Table 55 Advanced Menu –Intel TXT(LT) Configuration ............................. 48
Table 56 Advanced Menu – AMT Configuration ......................................... 48
Table 57 Advanced Menu –USB Configuration .......................................... 50
Table 58 Advanced Menu –H/W Monitor .................................................... 51
Table 59 Boot Menu ................................................................................... 52
Table 60 Security Menu ............................................................................. 53
Table 61 Save & Exit Menu ........................................................................ 53
KEEX-6100 User’s Manual
7
Safety Instructions
Safety Instructions
 Before You Begin
Before handling the product, read the instructions and safety guidelines on the
following pages to prevent damage to the product and to ensure your own personal
safety. Refer to the “Advisories” section in the Preface for advisory conventions used
in this user’s guide, including the distinction between Warnings, Cautions, Important
Notes, and Notes.


Always use caution when handling/operating a computer. Only qualified,
experienced, authorized electronics service personnel should access the
interior of a computer. The power supplies produce high voltages and
energy hazards, which can cause bodily harm.
Use extreme caution when installing or removing components. Refer to the
installation instructions in this user’s guide for precautions and procedures.
If you have any questions, please contact Quanmax Post-Sales Technical
Support.
WARNING
High voltages are present inside the chassis when the unit’s power cord is
plugged into an electrical outlet. Turn off system power, turn off the power
supply, and then disconnect the power cord from its source before
removing the chassis cover. Turning off the system power switch does not
remove power to components.
 When Working Inside a Computer
Before taking covers off a computer, perform the following steps:
1. Turn off the computer and any peripherals.
2. Disconnect the computer and peripherals from their power sources or
subsystems to prevent electric shock or system board damage. This does not
apply when hot swapping parts.
KEEX-6100 User’s Manual
8
Safety Instructions
3.
4.
Follow the guidelines provided in “Preventing Electrostatic Discharge” on the
following page.
Disconnect any telephone or telecommunications lines from the computer.
In addition, take note of these safety guidelines when appropriate:


To help avoid possible damage to system boards, wait five seconds after
turning off the computer before removing a component, removing a system
board, or disconnecting a peripheral device from the computer.
When you disconnect a cable, pull on its connector or on its strain-relief loop,
not on the cable itself. Some cables have a connector with locking tabs. If you
are disconnecting this type of cable, press in on the locking tabs before
disconnecting the cable. As you pull connectors apart, keep them evenly
aligned to avoid bending any connector pins. Also, before connecting a cable,
make sure both connectors are correctly oriented and aligned.
CAUTION
Do not attempt to service the system yourself except as explained in this
user’s guide. Follow installation and troubleshooting instructions closely.
 Preventing Electrostatic Discharge
Static electricity can harm system boards. Perform service at an ESD workstation
and follow proper ESD procedure to reduce the risk of damage to components.
Quanmax strongly encourages you to follow proper ESD procedure, which can
include wrist straps and smocks, when servicing equipment.
You can also take the following steps to prevent damage from electrostatic
discharge (ESD):

When unpacking a static-sensitive component from its shipping carton, do not
remove the component’s antistatic packing material until you are ready to install
the component in a computer. Just before unwrapping the antistatic packaging,
be sure you are at an ESD workstation or grounded. This will discharge any
static electricity that may have built up in your body.
KEEX-6100 User’s Manual
9
Safety Instructions




When transporting a sensitive component, first place it in an antistatic container
or packaging.
Handle all sensitive components at an ESD workstation. If possible, use
antistatic floor pads and workbench pads.
Handle components and boards with care. Don’t touch the components or
contacts on a board. Hold a board by its edges or by its metal mounting bracket.
Do not handle or store system boards near strong electrostatic, electromagnetic,
magnetic, or radioactive fields.
KEEX-6100 User’s Manual
10
Preface
Preface
 How to Use This Guide
This guide is designed to be used as step-by-step instructions for installation, and as
a reference for operation, troubleshooting, and upgrades.
NOTE
Driver downloads and additional information are available under
Downloads on our web site: www.quanmax.com.
 Unpacking
When unpacking, follow these steps:
1. After opening the box, save it and the packing material for possible future
shipment.
2. Remove all items from the box. If any items listed on the purchase order
are missing, notify Quanmax customer service immediately.
3. Inspect the product for damage. If there is damage, notify Quanmax
customer service immediately. Refer to “Warranty Policy” for the return
procedure.
 Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices.
FCC Compliance Statement for Class A Devices
The product(s) described in this user’s guide has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the user’s guide, may cause harmful
interference to radio communications. Operation of this equipment in a residential
KEEX-6100 User’s Manual
11
Preface
area (domestic environment) is likely to cause harmful interference, in which case
the user will be required to correct the interference (take adequate measures) at
their own expense.
Changes or modifications not expressly approved by Quanmax could void the user's
authority to operate the equipment.
NOTE
The assembler of a personal computer system may be required to test
the system and/or make necessary modifications if a system is found to
cause harmful interference or to be noncompliant with the appropriate
standards for its intended use.
 Warranty Policy
Limited Warranty
Quanmax Inc.’s detailed Limited Warranty policy can be found under Support at
www.quanmax.com. Please consult your distributor for warranty verification.
The limited warranty is void if the product has been subjected to alteration, neglect,
misuse, or abuse; if any repairs have been attempted by anyone other than
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God,
or other causes beyond the control of Quanmax or the manufacturer. Neglect,
misuse, and abuse shall include any installation, operation, or maintenance of the
product other than in accordance with the user’s guide.
No agent, dealer, distributor, service company, or other party is authorized to change,
modify, or extend the terms of this Limited Warranty in any manner whatsoever.
Quanmax reserves the right to make changes or improvements in any product
without incurring any obligation to similarly alter products previously purchased.
Return Procedure
For any Limited Warranty return, please contact Support at www.quanmax.com and
login to obtain a Return Material Authorization (RMA) Number. If you do not have an
account, send an email to support@quanmax.com to apply for one.
All product(s) returned to Quanmax for service or credit must be accompanied by a
Return Material Authorization (RMA) Number. Freight on all returned items must be
prepaid by the customer who is responsible for any loss or damage caused by
common carrier in transit. Returns for Warranty must include a Failure Report for
each unit, by serial number(s), as well as a copy of the original invoice showing the
KEEX-6100 User’s Manual
12
Preface
date of purchase.
To reduce risk of damage, returns of product must be in a Quanmax shipping
container. If the original container has been lost or damaged, new shipping
containers may be obtained from Quanmax Customer Service at a nominal cost.
Quanmax owns all parts removed from repaired products. Quanmax uses new and
reconditioned parts made by various manufacturers in performing warranty repairs
and building replacement products. If Quanmax repairs or replaces a product, its
warranty term is not extended.
Shipments not in compliance with this Limited Warranty Return Policy will not be
accepted by Quanmax.
Limitation of Liability
In no event shall Quanmax be liable for any defect in hardware, software, loss, or
inadequacy of data of any kind, or for any direct, indirect, incidental, or
consequential damages in connection with or arising out of the performance or use
of any product furnished hereunder. Quanmax’s liability shall in no event exceed the
purchase price of the product purchased hereunder. The foregoing limitation of
liability shall be equally applicable to any service provided by Quanmax or its
authorized agent.
 Maintaining Your Computer
Environmental Factors

Temperature
The ambient temperature within an enclosure may be greater than room
ambient temperature. Installation in an enclosure should be such that the
amount of air flow required for safe operation is not compromised.
Consideration should be given to the maximum rated ambient temperature.
Overheating can cause a variety of problems, including premature aging and
failure of chips or mechanical failure of devices.
If the system has been exposed to abnormally cold temperatures, allow a
two-hour warm-up period to bring it up to normal operating temperature before
turning it on. Failure to do so may cause damage to internal components,
particularly the hard disk drive.

Humidity
High-humidity can cause moisture to enter and accumulate in the system. This
moisture can cause corrosion of internal components and degrade such
KEEX-6100 User’s Manual
13
Preface
properties as electrical resistance and thermal conductivity. Extreme moisture
buildup inside the system can result in electrical shorts, which can cause
serious damage to the system.
Buildings in which climate is controlled usually maintain an acceptable level of
humidity for system equipment. However, if a system is located in an unusually
humid location, a dehumidifier can be used to maintain the humidity within an
acceptable range. Refer to the “Specifications” section of this user’s guide for
the operating and storage humidity specifications.

Altitude
Operating a system at a high altitude (low pressure) reduces the efficiency of
the cooling fans to cool the system. This can cause electrical problems related
to arcing and corona effects. This condition can also cause sealed components
with internal pressure, such as electrolytic capacitors, to fail or perform at
reduced efficiency.
Power Protection
The greatest threats to a system’s supply of power are power loss, power spikes,
and power surges caused by electrical storms, which interrupt system operation
and/or damage system components. To protect your system, always properly
ground power cables and one of the following devices.

Surge Protector
Surge protectors are available in a variety of types and usually provide a level
of protection proportional with the cost of the device. Surge protectors prevent
voltage spikes from entering a system through the AC power cord. Surge
protectors, however, do not offer protection against brownouts, which occur
when the voltage drops more than 20 percent below the normal AC line voltage
level.

Line Conditioner
Line conditioners go beyond the over voltage protection of surge protectors.
Line conditioners keep a system’s AC power source voltage at a fairly constant
level and, therefore, can handle brownouts. Because of this added protection,
line conditioners cost more than surge protectors. However, line conditioners
cannot protect against a complete loss of power.
KEEX-6100 User’s Manual
14
Preface

Uninterruptible Power Supply
Uninterruptible power supply (UPS) systems offer the most complete protection
against variations on power because they use battery power to keep the server
running when AC power is lost. The battery is charged by the AC power while it
is available, so when AC power is lost, the battery can provide power to the
system for a limited amount of time, depending on the UPS system.
UPS systems range in price from a few hundred dollars to several thousand
dollars, with the more expensive unit s allowing you to run larger systems for a
longer period of time when AC power is lost. UPS systems that provide only 5
minutes of battery power let you conduct an orderly shutdown of the system,
but are not intended to provide continued operation. Surge protectors should be
used with all UPS systems, and the UPS system should be Underwriters
Laboratories (UL) safety approved.
KEEX-6100 User’s Manual
15
Chapter 1
Chapter 1
Introduction
 Overview
The KEEX-6100 is an ECX Form Factor embedded single board computer (SBC) that
equips the latest 2nd generation Intel® Core™ i3/i5/i7 processors with the high
integration of the Intel® QM67/ HM65 chipset. Featured are DDR3 1066/1333
SO-DIMM up to 8GB, 2x 24-bit LVDS, HDMI, DP, VGA, 2x Gigabit Ethernet, 2x SATA,
mini PCIe slot, 8x USB 2.0, 2x COM ports with Power Selection, HD audio and
CompactFlash.
Checklist




Driver/ Manual CD
Quick Installation Guide
SATA Cable
KEEX-6100 main board
Features










®
2nd Generation Intel Core™ i3/i5/i7 Processors
®
Intel QM67 / HM65 Express Chipset
1x DDR3 SO-DIMM Socket
2x LVDS, HDMI, VGA, DP supported
1x mini PCIe
2x GbE
2x COM ports, 8x USB 2.0
2x 7-pin SATA connectors supported
1x CompactFlash socket onboard
Watchdog Timer, Hardware Monitor
KEEX-6100 User’s Manual
16
Chapter 1
 Product Specifications
Model Name
 KEEX-6100
Form Factor
 ECX (146mm x 105mm)
Processor
 2nd Generation Intel core i3/i5/i7 Processors with rPGA988B package
Memory
 1x SO-DIMM, dual channel DDR3, non-ECC supported, up to 8GB
®
Chipset
Graphics
Ethernet
Audio
Peripheral Support
 KEEX-6100---Intel QM67 Express Chipset
®
 KEEX-6101---Intel HM65 Express Chipset
 Intel HD Graphics 3000 rocessor graphics

1x VGA with DB-15 female connector

1x HDMI connector

1x DP Connector

2x 1x 30-pin SPWG connectors for 2x dual channel 24-bit LVDS

2x 1x 7-pin pitch 1.25 mm wafer connector for LVDS1 and LVDS2
backlight control
 2x Ethernet ports supported

1x Intel 82579LM Gb/s Ethernet PHY onboard as LAN1

1x Realtek RTL8111C Gb/s Ethernet controller onboard as LAN2

2x RJ-45 w/z Gb/s transformer connector on rear I/O

LAN1 with iAMT supported

Both LAN1 & LAN2 with WOL/PXE supported
 Realtek ALC662-VC HD codec onboard

1x 2W audio amplifier onboard

1x 2x 6-pins pitch 2.54mm header for Line-Out, Line-In and Mic-In;
Pin definition is as shown below:
Pin Description
Pin #
Pin #
Pin Description
Mic-In_L
1
2
Mic-In_R
Mic-In Jack Detect
3
4
Audio_GND
Line-In 1_L
5
6
Line-In 1_R
Line-In Jack 1 Detect
7
8
Audio_GND
Line-Out_L
9
10
Line-Out_R
Line-Out Jack Detect
11
12
Audio_GND

2x 2-pins pitch 2.0 mm wafer connector for Right/Left speaker out

1x 1x 4-pin pitch 2.54 mm header for S/PDIF
 Storage supported

2x 7-pin SATA connectors supported on top side of the board

1x 4-pin connector onboard with +5V and +12V supported for SATA
device.

1x CF socket
 8x USB2.0 ports supported

4x USB 2.0 ports offer on front I/O, stack with RJ-45.

2x 2x5-in pitch 2.54 mm headers for 4x USB 2.0 ports onboard for
internal use.
 2x COM ports supported

2x 1x10-pin pitch 1.27 mm wafer connectors onboard for COM1 and
COM2

COM1 with RS-232/422/485 supported.

COM2 with RS-232 only.
KEEX-6100 User’s Manual
17
Chapter 1




Expansion Slot
1x 1x6-pin pitch 2.00 mm wafer connector for PS/2 keyboard and mouse.
1x 1x5-pin pitch 2.54mm header for IrDA supported.
1x 1x3-pin fan connector onboard with smart fan supported.
1x 2x 5-pin pitch 2.54 mm header onboard for 8-bit DIO.

4-bit input and 4-bit output.

DIO default setting is “H”.
 1x full size mini-PCIe X8 slot supported
 1x connector onboard for SIM card signals supported
Super I/O chip
 Fintek F71869ED
RTC








Battery
 1x 2-pin wafer connector onboard for fly-wire CR2032 battery supported
Hardware Monitor
TPM
BIOS
Voltage monitoring
CPU and system temperatures detection
Fan detection
TPM 1.2 supported
AMI uEFI Plug & Play SPI BIOS
iAMT 7.0 supported
Watchdog Timer supported, 1-255 step offered
Chipset internal RTC
OS Supported




Operation Temp.
 0ºC – 60ºC
Storage Temp.
 -20ºC – 80ºC
Humidity
 0% – 95% RH
Certifications
 CE, FCC Class A
Power
1x +12VDC Power Input
1x +12VDC & +5VDC HDD Power output
ATX/ AT Mode Supported
Windows XP/XPe/Windows 7
Table 1 KEEX-6100 Specification
KEEX-6100 User’s Manual
18
Chapter 1
 System Block Diagram
Figure 1 Block Diagram
KEEX-6100 User’s Manual
19
Chapter 1
 Mechanical Dimensions
KEEX-6100 User’s Manual
20
Chapter 1
Figure 2 Mechanical Dimensions
KEEX-6100 User’s Manual
21
Chapter 2
Chapter 2
Hardware Settings
 Overview
This chapter provides the definitions and locations of jumpers, headers, and
connectors.
Jumpers
The product has several jumpers which must be properly configured to ensure
correct operation.
Figure 3 Jumper Connector
For a three-pin jumper (see Figure 3), the jumper setting is designated “1-2” when
the jumper connects pins 1 and 2. The jumper setting is designated “2-3” when pins
2 and 3 are connected and so on. You will see that one of the lines surrounding a
jumper pin is thick, which indicates pin No.1.
To move a jumper from one position to another, use needle-nose pliers or tweezers
to pull the pin cap off the pins and move it to the desired position.
KEEX-6100 User’s Manual
22
Chapter 2
 Jumper Settings and Pin Definitions
For jumper and connector locations, please refer to the diagrams below.
Figure 4 Jumper and Connector Locations
KEEX-6100 User’s Manual
23
Chapter 2
Jumper Settings
To ensure correct system configuration, the following section describes how to set
the jumpers to enable/disable or change functions. For jumper descriptions, please
refer to the table below.
Table 2 Jumper List
Label
JP1
JP2
JP3
JP4
JP5
JP6
JP7
JP8
Function
ME F/W Selection
Panel & Backlight Power Selection for LVDS2
Panel & Backlight Power Selection for LVDS1
Backlight Power Enable Selection for LVDS1
Backlight Power Enable Selection for LVDS2
AT / ATX Mode Selection
SRTC Reset Selection
RTC Reset Selection
Table 3 JP1 ME F/W Selection
1
2
Jumper
1-2 Open
Status
Normal Operation.
1-2 Short
ME F/W Disabled.
Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)]
Table 4 JP2 Panel & Backlight Power Selection for LVDS2
Jumper
1
2
1
5
6
2
Setting
1-3
Function
Backlight Power = +12V
3-5
Backlight Power = +5V
2-4
4-6
Panel Power = +3.3V
Panel Power = +5V
Pitch:2.54mm [YIMTEX 3362*03SAGR]
KEEX-6100 User’s Manual
24
Chapter 2
Table 5 JP3 Panel Backlight Power Selection for LVDS1
1
2
5
6
Jumper
1
Setting
1-3
3-5
2-4
4-6
2
Status
Backlight Power = +12V
Backlight Power = +5V
Panel Power = +3.3V
Panel Power = +5V
Pitch:2.54mm [YIMTEX 3362*03SAGR]
Table 6 JP4 Backlight Power Enable Selection for LVDS1
Jumper
1
2
5
Setting
1-3
1
2
6
Status
Backlight Enable Voltage = +3.3V
3-5
2-4
Backlight Enable Voltage = +5V
Active High
4-6
Active Low
Pitch:2.0mm[PINREX 222-97-03GBB1]
Table 7 JP5 Backlight Power Enable Selection for LVDS2
Jumper
1
2
5
6
1
2
Setting
1-3
3-5
2-4
Status
Backlight Enable Voltage = +3.3V
Backlight Enable Voltage = +5V
Active High
4-6
Active Low
Pitch:2.0mm[PINREX 222-97-03GBB1]
Table 8 JP6 AT/ATX Mode Selection
1
2
3
Jumper
1-2 Short
2-3 Short
Status
ATX Mode
AT Mode
Pitch: Pitch:2.0mm [YIMTEX 3291*03SAGR(6T)]
Table 9 JP7 SRTC Reset Selection
1
2
Jumper
Status
1-2 Open
Normal Operation
1-2 Short
Clear ME Registers
Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)]
Table 10 JP8 RTC Reset Selection
1
Jumper
1-2 Open
Status
Normal Operation
2
1-2 Short
Clear RTC CMOS
Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)]
KEEX-6100 User’s Manual
25
Chapter 2
Rear Panel Pin Assignments
Figure 5 Rear Panel IO
Table 11 Rear Panel Connector List
Label
CN9
CN10
DP1
HDMI1
VGA1
Function
LAN1 & USB2.0 Port 0,1 Connector
LAN2 & USB2.0 Port 8,9 Connector
Display Port Connector
HDMI Connector
DB-15 VGA Connector
Table 12 CN9 LAN1 & USB 2.0 Port 0, 1 Connector
Pin
1
2
3
4
5
6
7
8
Signal
MDI[0]+
MDI[0]MDI[1]+
MDI[1]MDI[2]+
MDI[2]MDI[3]+
MDI[3]-
Pin
9
10
11
12
13
14
15
16
Signal
+USBVCC
USB_AUSB_A+
GND
+USBVCC
USB_BUSB_B+
GND
[UDE RU1-161F9WGF(XB)]
Table 13 CN10 LAN2 & USB 2.0 Port 8, 9 Connector
Pin
1
2
3
4
5
6
7
8
Signal
MDI[0]+
MDI[0]MDI[1]+
MDI[1]MDI[2]+
MDI[2]MDI[3]+
MDI[3]-
[UDE RU1-161F9WGF(XB)]
KEEX-6100 User’s Manual
26
Pin
9
10
11
12
13
14
15
16
Signal
+USBVCC
USB_AUSB_A+
GND
+USBVCC
USB_BUSB_B+
GND
Chapter 2
Table 14 DP1 Display Port Connector
Pin
1
2
3
4
5
6
7
8
9
10
Signal
TX0+
GND
TX0TX1+
GND
TX1TX2+
GND
TX2TX3+
Pin
11
12
13
14
15
16
17
18
19
20
Signal
GND
TX3GND
GND
AUX+
GND
AUXHPD
GND
PWR
[WIN WIN WDPE-20F3L1BU3]
Table 15 HDMI1 HDMI Connector
Pin
Signal
1
TMDS Data2+
2
Ground
3
TMDS Data2–
4
TMDS Data1+
5
Ground
6
TMDS Data1–
7
TMDS Data0+
8
Ground
9
TMDS Data0–
10
TMDS Clock+
11
Ground
12
TMDS Clock–
13
Reserved
14
Reserved
15
DDC_CLK
16
DDC_DATA
17
Ground
18
+5 V Power
19
Hot Plug Detect
[Foxconn QJ51193-HEB4-4F]
Table 16 VGA1 DB-15 VGA Connector
Signal Name
Red
Blue
GND
GND
VCC
NC
HSYNC
DDC clock
Pin
1
3
5
7
9
11
13
15
Pin
2
4
6
8
10
12
14
[ FEN YING SM1003S01012PN]
KEEX-6100 User’s Manual
27
Signal Name
Green
NC
GND
GND
GND
DDC data
VSYNC
Chapter 2
Main Board Pin Assignments
Table 17 Internal Connector List
Label
ATX1
BAT1
BZ1
CFD1
COM1
COM2
CN1
CN2
CN3
CN4
CN5
CN6
CN7
CN8
CN12
CN13
CN14
CN20
DIMM1
FAN1
FP1
FP2
IR1
LVDS1
LVDS2
MPCIE1
SATA1
SATA2
Function
+12V Power Input Connector
CR2032 Battery Power Input Wafer
Onboard Buzzer
CF Type II Connector
RS-232/422/485 Port 1 Wafer
RS-232 Port 2 Wafer
Digital Input / Output Pin Header
SATA HDD Power Output Wafer
Backlight Power Output Wafer for LVDS1
SIM Interface Wafer for MPCIE1
USB2.0 Port 2, 3 Pin Header
USB2.0 Port 10, 11 Pin Header
S/PDIF Pin Header
Audio Pin Header
Left Channel 2W Audio AMP Output Wafer
Right Channel 2W Audio AMP Output Wafer
Backlight Power Output Wafer for LVDS2
Keyboard & Mouse Wafer
DDR3 Memory SO-DIMM Socket
CPU FAN Wafer
Front Panel 1 Pin Header
Front Panel 2 Pin Header
IrDA Pin Header
Primary 24-bit, 2-channel LVDS Panel Connector
Secondary 24-bit, 2-channel LVDS Panel Connector
Mini-PCIE Express v1.2 Socket
Serial ATA Port 0 Connector
Serial ATA Port 1 Connector
Table 18 ATX2 +12V Power Input Connector
Pin
1
2
3
4
Signal Name
GND
GND
+12V
+12V
Pitch:4.2mm [YIMTEX 576MWA2*02STR]
Table 19 CR2032 Battery Power Input Wafer
Pin
1
2
Signal Name
+VBAT
GND
Pitch:1.25mm [Pinrex 712-73-02TWR0]
KEEX-6100 User’s Manual
28
Chapter 2
Table 20 CFD1 CF Type II Connector
Signal Name
GND
IDE Data 3
IDE Data 4
IDE Data 5
IDE Data 6
IDE Data 7
IDE Chip select 1#
GND
GND
GND
GND
GND
+5V
GND
GND
GND
GND
SDA2
IDE Address 1
IDE Address 0
IDE Data 0
IDE Data 1
IDE Data 2
IOIS16#
GND
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Pin
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Signal Name
GND
IDE Data 11
IDE Data 12
IDE Data 13
IDE Data 14
IDE Data 15
IDE Chip select 3#
GND
IDEIOR#
IDEIOW#
+5V
IDEIRQ
+5V
PCSEL
NC
Reset IDE
IDEIORDY
DREQ
DACK#
IDE activity
PDIAG#
IDE Data 8
IDE Data 9
IDE Data 10
GND
[KINGFON CFCMD-45T15W100]
KEEX-6100 User’s Manual
29
Chapter 2
Table 21 COM1 RS-232/422/485 Port 1 Wafer
Pin
RS-232
RS-422
1
DCD
TX2
DSR
N/A
3
RXD
RX+
4
RTS
N/A
5
TXD
TX+
6
CTS
N/A
7
DTR
RX8
RI
N/A
9
GND
GND
10
+5V
+5V
Pitch:1.25mm [Pinrex 712-73-10TWB0]
Half Duplex
RS-485
Full Duplex
RS-485
DATAN/A
N/A
N/A
DATA+
N/A
N/A
N/A
GND
+5V
TXN/A
RX+
N/A
TX+
N/A
RXN/A
GND
+5V
Table 22 COM2 RS-232 Port 2 Wafer
Pin
1
2
3
4
5
6
7
8
9
10
Signal Name
DCD
DSR
RXD
RTS
TXD
CTS
DTR
RI
GND
+5V
Pitch:1.25mm [Pinrex 712-73-10TWB0]
Table 23 CN1 Digital Input / Output Pin Header
1
2
9
10
Pin
1
3
5
7
9
Signal
Digital Output 0
Digital Output 1
Digital Output 2
Digital Output 3
+5V
Pin
2
4
6
8
10
Signal
Digital Input 0
Digital Input 1
Digital Input 2
Digital Input 3
GND
Pitch:2.54mm [YIMTEX 3362*05SANGR]
Table 24 CN2 SATA HDD Power Output Wafer
1
2
3
4
Pin
1
2
3
4
Signal Name
+12V
GND
GND
+5V
Pitch:2.5mm [YIMTEX 512CW4ST-2R]
KEEX-6100 User’s Manual
30
Chapter 2
Table 25 CN3 Backlight Power Output Wafer for LVDS1
Pin
1
2
3
4
5
6
7
Signal Name
BL_ADJ_PWM *
BL_ADJ_VOL *
GND
+5V / +12V **
+5V / +12V **
GND
BL_EN***
Pitch:1.25mm [YIMTEX 501MW1X07MTR-1R]
*:BL_ADJ can be setting in BIOS setup.
**:Backlight Power can be selected by JP3.
***:BL_EN can be selected by JP4.
Table 26 CN4 SIM Interface Wafer for MPCIE1
Pin
1
2
3
4
5
6
Signal Name
UIM_PWR
UIM_DATA
UIM_RESET
UIM_VPP
UIM_CLK
GND
Pitch:1.25mm [Pinrex 712-73-06TWB0]
Table 27 CN5 USB 2.0 Port 2, 3 Pin Header
1
2
3
4
5
6
7
8
10
Pin
Signal Name
Pin
Signal Name
1
+USBVCC
2
+USBVCC
3
USB_A4
USB_B5
USB_A+
6
USB_B+
7
GND
8
GND
9
KEY
10
GND
Pitch:2.54mm [YIMTEX 3362*05SANGR-09]
Table 28 CN6 USB 2.0 Port 10, 11 Pin Header
1
2
3
4
5
6
7
8
10
Pin
1
3
5
7
9
Signal Name
+USBVCC
USB_AUSB_A+
GND
KEY
Pin
2
4
6
8
10
Signal Name
+USBVCC
USB_BUSB_B+
GND
GND
Pitch:2.54mm [YIMTEX 3362*05SANGR-09]
KEEX-6100 User’s Manual
31
Chapter 2
Table 29 CN7 S/PDIF Pin Header
Pin
1
2
3
4
1
4
Signal Name
S/PDIF Input
GND
S/PDIF Output
GND
Pitch:2.54mm [YIMTEX 3321*04SAGR(6T)]
Table 30 CN8 Audio Pin Header
1
2
11
12
Pin
1
3
5
7
9
11
Signal Name
MIC_IN_L
MIC_IN_JD
LINE_IN_L
LINE_IN_JD
LINE_OUT_L
LINE_OUT_JD
Pin
2
4
6
8
10
12
Signal Name
MIC_IN_R
GND
LINE_IN_R
GND
LINE_OUT_R
GND
Pitch:2.54mm [PINREX 212-92-06GB01]
Table 31 CN12 Left Channel 2W Audio AMP Output Wafer
Pin
1
Signal Name
Speaker+
2
Speaker-
Pitch:2.0mm [YIMTEX 503PW1*02STR]
Table 32 CN13 Right Channel 2W Audio AMP Output Wafer
Pin
1
Signal Name
Speaker+
2
SpeakerPitch:2.0mm [YIMTEX 503PW1*02STR]
Table 33 CN14 Backlight Power Output Wafer for LVDS2
Pin
1
2
3
4
5
6
7
Signal Name
BL_EN***
GND
+5V / +12V **
+5V / +12V **
GND
BL_ADJ_VOL *
BL_ADJ_PWM *
Pitch:1.25mm [YIMTEX 501MW1X07MTR-1R]
*:BL_ADJ can be setting in BIOS setup.
**:Backlight Power can be selected by JP2.
***:BL_EN can be selected by JP5
KEEX-6100 User’s Manual
32
Chapter 2
Table 34 CN20 Keyboard & Mouse Wafer
Pin
1
2
3
4
5
6
Signal Name
MSCLK
VCC
MSDAT*
KBDAT
GND
KBCLK
Pitch:2.0mm [YIMTEX 503PW1*06STR]
Table 35 DIMM1 DDR3 Memory SO-DIMM Socket
Height: 7.0mm [LINKTEK DDRRK-20401-TP7B]
Table 36 FAN1 CPU FAN Wafer
Pin
1
2
3
1
2
Signal
GND
+12V*
FAN_RPM
3
*: PWM Fan control supported.
Table 37 FP1 Front Panel 1 Pin Header
RSTBTN
HLED
+ 1
2 +
-
SPKR
+
-
8
7
-
Pin
1
3
5
7
Signal
Reset Button +
Reset Button HDD LED +
HDD LED -
Pin
2
4
6
8
Signal
Speaker +
NC
Internal SpeakerSpeaker -
Pitch:2.54mm [YIMTEX 3362*04SANGR]
Note: Internal Buzzer is enabled when Pin6-8 is shorted.
Table 38 FP2 Front Panel 2 Pin Header
2 +
+ 1
PLED
-
PWRBTN
KLOCK
SMD
+
-
10 SMC
9
Pin
1
3
5
7
9
Signal
Power LED +
NC
Power LED Keyboard Lock
GND
Pin
2
4
6
8
10
Signal
Power Button +
Power Button NC
SMBus Data
SMBus Clock
Pitch:2.54mm [YIMTEX 3362*05SANGR]
Table 39 IR1 IrDA Pin Header
1
5
KEEX-6100 User’s Manual
Pin
Signal Name
1
+5V
2
Key
3
IR_Rx
4
GND
5
IR_Tx
Pitch:2.54mm [YIMTEX 3321*05SAGR(6T)-02]
33
Chapter 2
Table 40 LVDS1 Primary 24-bit, 2-channel LVDS Panel Connector
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal Name
LVDS_A0LVDS_A0+
LVDS_A1LVDS_A1+
LVDS_A2LVDS_A2+
GND
LVDS_ACLKLVDS_ACLK+
LVDS_A3-/NC
LVDS_A3+/NC
LVDS_B0LVDS_B0+
GND
LVDS_B1-
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal Name
LVDS_B1+
GND
LVDS_B2LVDS_B2+
LVDSBCLKLVDS_BCLK+
LVDS_B3-/NC
LVDS_B3+/NC
GND
DDC_DATA
VDDEN
DDC_CLK
+3.3V / +5V *
+3.3V / +5V *
+3.3V / +5V *
Pitch:1.0mm [JAE FI-X30SSL-HF]
*: Panel Power can be selected by JP3.
Table 41 LVDS2 Secondary 24-bit, 2-channel LVDS Panel Connector
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal Name
LVDS_A0LVDS_A0+
LVDS_A1LVDS_A1+
LVDS_A2LVDS_A2+
GND
LVDS_ACLKLVDS_ACLK+
LVDS_A3-/NC
LVDS_A3+/NC
LVDS_B0LVDS_B0+
GND
LVDS_B1-
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal Name
LVDS_B1+
GND
LVDS_B2LVDS_B2+
LVDSBCLKLVDS_BCLK+
LVDS_B3-/NC
LVDS_B3+/NC
GND
DDC_DATA
VDDEN
DDC_CLK
+3.3V / +5V *
+3.3V / +5V *
+3.3V / +5V *
Pitch:1.0mm [JAE FI-X30SSL-HF]
*: Panel Power can be selected by JP2.
KEEX-6100 User’s Manual
34
Chapter 2
Table 42 MPCIE1 Mini-PCIE Express v 1.2 Socket
Signal
WAKE#
Reserved
Reserved
CLKREQ#
Ground
REFCLKREFCLK+
Ground
Reserved
Reserved
Ground
PERn0
PERp0
Ground
Ground
PETn0
PETp0
Ground
Ground
+3.3VSB
+3.3VSB
Ground
Reserved
Reserved
Reserved
Reserved
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
Signal
+3.3VSB
Ground
+1.5V
UIM_PWR*
UIM_DATA*
UIM_CLK*
UIM_RESET*
UIM_VPP*
Ground
W_Disable#
PERST#
+3.3VSB
Ground
+1.5V
SMB_CLK
SMB_DATA
Ground
USB_DUSB_D+
Ground
LED_WWAN#
LED_WLAN#
LED_WPAN#
+1.5V
Ground
+3.3VSB
Height:9.9mm [FOXCONN AS0B226-S99Q-7H]
*: These pins are connected to CN4 directly.
KEEX-6100 User’s Manual
35
Chapter 2
Table 43 SATA1 Serial ATA Port 0 Connector
Pin
1
2
3
4
5
6
7
Signal Name
GND
TX+
TXGND
RXRX+
GND
[FOXCONN LD1807V-S52U]
Table 44 SATA2 Serial ATA Port 1 Connector
Pin
Signal Name
1
GND
2
TX+
3
TX4
GND
5
RX6
RX+
7
GND
[FOXCONN LD1807V-S52U]
KEEX-6100 User’s Manual
36
Chapter 3
Chapter 3
System Installation
 Expansion Interfaces


1x full size mini-PCIe slot supported
1x connector onboard for SIM card signals supported
NOTE
When adding or removing expansion cards, make sure that you unplug the
power supply first. Meanwhile, read the documentation for the expansion card
to configure any necessary hardware or software settings for the expansion
card, such as jumpers, switches or BIOS configuration.
 Memory Module Installation
Carefully follow the steps below in order to install the DIMMs:
1.
2.
3.
To avoid generating static electricity and damaging the SO-DIMM, ground
yourself by touching a grounded metal surface or use a ground strap before you
touch the SO-DIMM.
Do not touch the connectors of the SO-DIMM. Dirt or other residue may cause a
malfunction.
Hold the SO-DIMM with its notch aligned with the memory socket of the board
and insert it at a 30-degree angle into the socket.
Figure 6 Align the SO-DIMM Memory Module with the onboard socket
KEEX-6100 User’s Manual
37
Chapter 3
4.
5.
Fully insert the module into the socket until a “click” is heard.
Press down on the SO-DIMM so that the tabs of the socket lock on both sides
of the module
Figure 7 Press down on the SO-DIMM Memory Module to lock it in place
Removing a DIMM:
To remove the SO-DIMM, use your fingers or a small screwdriver to carefully push
away the tabs that secure either side of the SO-DIMM. Lift it out of the socket.
Make sure you store the SO-DIMM in an anti-static bag. The socket must be
populated with memory modules of the same size and manufacturer.
KEEX-6100 User’s Manual
38
Chapter 4
Chapter 4
AMI BIOS Setup
 Overview
This chapter provides a description of the AMI BIOS. The BIOS setup menus and
available selections may vary from those of your product. For specific information on
the BIOS for your product, please contact Quanmax.
NOTE: The BIOS menus and selections for your product may vary from
those in this chapter. For the BIOS manual specific to your product, please
contact Quanmax
AMI's ROM BIOS provides a built-in Setup program, which allows the user to modify
the basic system configuration and hardware parameters. The modified data will be
stored in a battery-backed CMOS, so that data will be retained even when the power
is turned off. In general, the information saved in the CMOS RAM will not need to be
changed unless there is a configuration change in the system, such as a hard drive
replacement or when a device is added.
It is possible for the CMOS battery to fail, which will cause data loss in the CMOS
only. If this happens you will need to reconfigure your BIOS settings.
KEEX-6100 User’s Manual
39
Chapter 4
 Main Menu
The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test
(POST) memory test begins and before the operating system boot begins. Once you
enter the BIOS Setup Utility, the Main Menu will appear on the screen. The Main
Menu provides System Overview information and allows you to set the System Time
and Date. Use the “<” and “>” cursor keys to navigate between menu screens.
Table 45 BIOS Main Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
BIOS Information
Version
Build Date
0.04
06/14/2011
CPU Information
Intel® Core ™ i5-2540M CPU @ 2.60GHz
Microcode Revision
Processor Cores
14
2
Memory Information
Total Size
Frequency
2048 MB (DDR3)
1067 MHz
System date
System time
[Wed 07/06/2011]
[17:21:40]
Save
40
Exit
Set the Date. Use Tab to
switch between Data
elements.
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
KEEX-6100 User’s Manual
&
Chapter 4
 Advanced Menu
Table 46 Advanced Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Onboard LAN1 Controller
Onboard LAN1 Boot
Onboard LAN2 Controller
Onboard LAN2 Boot
Audio Controller
Security
[Enabled]
[Disabled]
[Enabled]
[Disabled]
[Enabled]
>Display Configuration
>Super IO Configuration
>Power Management Configuration
>CPU Advanced Configuration
>Trusted Computing
>SATA Configuration
>Intel TXT(LT) Configuration
>AMT Configuration
>USB Configuration
>H/W Monitor
Server
Mgmt
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Onboard LAN Controller
Options: Disabled, Enabled
Onboard LAN Boot
Options: Disabled, Enabled
Audio Controller
Options: Disabled, Enabled, Auto
41
Exit
Enable or Disable Onboard
LAN1.
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
KEEX-6100 User’s Manual
Save &
Chapter 4
Table 47 Advanced Menu – Display Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
Server
Mgmt
Display Configuration
Primary Display
Internal Graphics
Aperture Size
DVMT Pre-Allocated
DVMT Total Gfx Mem
[Auto]
[Auto]
[256 MB]
[64M]
[256 M]
IGFX – Boot Type
IGFX – 2nd Boot Type
Active LVDS1
LVDS1 Panel Type
LVDS1 Panel Color Depth
LVDS2 Panel Type
LVDS1 Backlight Control – Voltage
LVDS2 Backlight Control – Voltage
[VBIOS Default]
[Disabled]
[Disabled]
[VBIOS Default]
[18 bit]
[1024 x 768 18 Bit 1CH]
[2.5V]
[2.5V]
Save &
Exit
Select which of IGFX/PEG/PCI
Graphics device should be
Primary Display or Select SG
for Switchable Gfx.
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
Primary Display
Options: Auto, IGFX, PEG, PCI
Internal Graphics
Options: Auto, Disabled, Enabled
Aperture Size
Options: 128MB, 256MB, 512MB
DVMT Pre-Allocated
Options: 0M, 32M, 64M, 96M, 128M, 160M, 192M, 224M, 256M, 288M, 320M,
352M, 384M, 416M, 448M, 480M, 512M
DVMT Total Gfx Mem
Options: 128M, 256M, MAX
IGFX – Boot Type
Options: VBIOS Default, CRT, LVDS1, HDMI, DP, LVDS2
IGFX – 2nd Boot Type
Options: Disabled, CRT, LVDS1, HDMI, DP, LVDS2
Active LVDS1
Options: Disabled, Enabled
LVDS1 Panel Type
Options: VBIOS Default, 1024x768 LVDS, 1280x1024 LVDS, 1366x768 LVDS,
1920x1080 LVDS
LVDS1 Panel Color Depth
Options: 18 Bit, 24 Bit
KEEX-6100 User’s Manual
42
Chapter 4
LVDS2 Panel Type
Options: 640x480 18Bit 1CH, 800x480 18Bit 1CH, 800x600 18Bit 1CH, 1024x768
18Bit 1CH, 1440x900 18Bit 2CH, 1600x900 18Bit 2CH, 800x480 24Bit 1CH,
800x600 24Bit 1CH, 1024x768 24Bit 1CH, 1280x1024 24Bit 2CH, 1366x768 24Bit
1CH, 1366x768 24Bit 2CH, 1440x900 24Bit 2CH, 1600x1200 24Bit 2CH,
1920x1080 24Bit 2CH, 1920x1200 24Bit 2CH
LVDS1 Backlight Control – Voltage
Options: 0.0V, 0.5V, 1.0V, 1.5V, 2.0V, 2.5V, 3.0V, 3.5V, 4.0V, 4.5V, 5.0V
LVDS2 Backlight Control – Voltage
Options: 0.0V, 0.5V, 1.0V, 1.5V, 2.0V, 2.5V, 3.0V, 3.5V, 4.0V, 4.5V, 5.0V
Table 48 Advanced Menu – Super IO Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Super IO Configuration
Security
Save
&
Set Parameters of Serial Port 1
(COM1)
>Serial Port 1 Configuration
>Serial Port 2 Configuration
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
KEEX-6100 User’s Manual
Exit
43
Chapter 4
Table 49 Advanced Menu – Super IO Configuration – Serial Port 1 Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
Serial Port 1 Configuration
Save
&
Exit
Enable or Disable Serial Port
(COM)
Serial Port
Device Settings
[Enabled]
IO=3F8h; IRQ=4;
Change Settings
Serial Port 1 Type
[Auto]
[RS232]
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
Serial Port
Options: Disabled, Enabled
Change Settings
Options: Auto, IO=3F8h; IRQ=4; IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; IO=2F8h;
IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; IO=2E8h;
IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;
Serial Port Type
Options: RS232, RS422, RS485
Table 50 Advanced Menu – Super IO Configuration – Serial Port 2 Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
Serial Port 2 Configuration
Save
Exit
Enable or Disable Serial Port
(COM)
Serial Port
Device Settings
[Enabled]
IO=2F8h; IRQ=3;
Change Settings
Device Mode
[Auto]
[Standard Serial Po…]
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
Serial Port
Options: Disabled, Enabled
KEEX-6100 User’s Manual
&
44
Chapter 4
Change Settings
Options: Auto, IO=2F8h; IRQ=3; IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; IO=2F8h;
IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; IO=2E8h;
IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;
Device Mode
Options: Standard Serial Port Mode, IrDA function, active pulse is 1.6us, IrDA
function, active pulse is 3/16 bit time.
Table 51 Advanced Menu –Power Management Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
Server
Power Management Configuration
ACPI Sleep State
Restore AC Power Loss
Resume from S3 By PS/2 keyboard
Resume from S3 By PS/2 mouse
Resume By PCIE Device
Resume By RTC Alarm
EUP Power Saving Mode
>Watchdog Timer Configuration
[S3 (Suspend to…)
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
Mgmt
Save &
Select the highest ACPI sleep
state the system will enter,
when the SUSPEND button is
pressed.
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
ACPI Sleep State
Options: Suspend Disabled, S1 (CPU Stop Clock), S3 (Suspend to RAM)
Restore AC Power Loss
Options: Power Off, Power On, Last State
Resume From S By PS/2 keyboard
Options: Disabled, Enabled
Resume From S By PS/2 mouse
Options: Disabled, Enabled
Resume By PCIE Device
Options: Disabled, Enabled
Resume By RTC Alarm
Options: Disabled, Enabled
EUP Power Saving Mode
Options: Disabled, Enabled
Watchdog Timer Configuration
KEEX-6100 User’s Manual
45
Exit
Chapter 4
Options: Disabled, Enabled
Table 52 Advanced Menu –CPU Advanced Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
CPU Advanced Configuration
EIST
Turbo Mode
Intel ® Virtualization Tech
VT-d
Intel ® Hyper Treading Tech
Active Processor Cores
Limit CPUID Maximum
Execute Disable Bit
Save
Exit
Enable/Disable Intel ® Speed
Step ™ Tech.
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[All]
[Disabled]
[Enabled]
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
EIST
Options: Disabled, Enabled
Turbo Mode
Options: Disabled, Enabled
Intel ® Virtualization Tech
Options: Disabled, Enabled
VT-d
Options: Disabled, Enabled
Intel ® Hyper Threading Tech
Options: Disabled, Enabled
Active Processor Cores
Options: All, 1
Limit CPUID Maximum
Options: Disabled, Enabled
Execute Disable Bit
Options: Disabled, Enabled
KEEX-6100 User’s Manual
&
46
Chapter 4
Table 53 Advanced Menu –Trusted Computing
BIOS SETUP UTILITY
Main
Advanced
Boot
TPM Configuration
TPM SUPPORT
Security
Save
&
Exit
Enable/Disable TPM support.
O.S. will not show TPM. Reset of
platform is required.
[Disable]
Current TPM Status Information
TPM SUPPORT OFF
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
TPM
Options: Disabled, Enabled
Table 54 Advanced Menu –SATA Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
SATA Controller(s)
SATA Mode Selection
[Enabled]
[IDE]
Serial ATA Port 1
Software Preserve
Serial ATA Port 2
Software Preserve
WDC WD6402AAEX (640.1
SUPPORTED
Empty
Unknown
Save
&
Enable or Disable SATA Device.
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
SATA Controller(s)
Options: Disabled, Enabled
SATA Mode Selection
Options: IDE, AHCI, RAID
KEEX-6100 User’s Manual
47
Exit
Chapter 4
Table 55 Advanced Menu –Intel TXT(LT) Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
Save
&
Exit
Intel Trusted Execution technology Configuration
Intel TXT support only can be enabled / disabled if SMX enabled. And must
enables the VT support prior to TXT.
Secure Mode Extensions (SMX)
Intel TXT(LT) Support
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
[Enabled]
[Disabled]
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
Table 56 Advanced Menu – AMT Configuration
BIOS SETUP UTILITY
Main
Advanced
Intel AMT
Intel AMT Setup Prompt
BIOS Hotkey Pressed
MEBx Selection Screen
Verbose MEBx Output
Hide Un-Configure ME Confirmation
MEBx Debug Message Output
Un-Configure ME
Intel AMT Password Write Enabled
AMT Wait Timer
ASF
Activate Remote Assistance Process
USB Configure
PET Progress
Intel AMT SPI Protected
AMT CIRA Timeout
Watchdog
OS Timer
BIOS Timer
Boot
Security
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
0
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[Disabled]
0
[Disabled]
0
0
Save
Intel AMT Setup Prompt
Options: Disabled, Enabled
BIOS Hotkey Pressed
Options: Disabled, Enabled
KEEX-6100 User’s Manual
48
Exit
Enable/Disable Intel ® Active
Management Technology BIOS
Extension.
Note: iAMT H/W is always
enabled.
This option just controls the BIOS
extension execution.
If enabled, this requires additional
firmware in the SPI device
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
Intel AMT
Options: Disabled, Enabled
&
Chapter 4
MEBx Selection Screen
Options: Disabled, Enabled
Verbose MEBx Output
Options: Disabled, Enabled
Hide Un-Configure ME Confirmation
Options: Disabled, Enabled
MEBx Debug Message Output
Un-Configure ME
Options: Disabled, Enabled
Intel AMT Password Write Enabled
Options: Disabled, Enabled
AMT Wait Timer
Options: 0 only
ASF
Options: Disabled, Enabled
Activate Remote Assistance Process
Options: Disabled, Enabled
USB Configure
Options: Disabled, Enabled
PET Progress
Options: Disabled, Enabled
Intel AMT SPI Protected
Options: Disabled, Enabled
Watchdog
Options: Disabled, Enabled
KEEX-6100 User’s Manual
49
Chapter 4
Table 57 Advanced Menu –USB Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
USB Configuration
USB Devices:
2 Hubs
Legacy USB Support
EHCI Hand-off
[Enabled]
[Disabled]
USB hardware delays and time-out:
USB transfer time-out
Device reset time-out
Device power-up delay
[20 sec]
[20 sec]
[Auto]
Save
EHCI hand-off
Options: Disabled, Enabled
USB Transfer Time-Out
Options: 1, 5, 10, 20 sec.
Device Transfer Time-Out
Options: 10, 20, 30, 40 sec.
Device Power-Up Delay
Options: Auto, Manual
KEEX-6100 User’s Manual
50
Exit
Enables Legacy USB support.
AUTO option disables legacy
support if no USB devices are
connected. DISABLE option will
keep USB devices available only
for EFI applications.
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
Legacy USB Support
Options: Disabled, Enabled, Auto
&
Chapter 4
Table 58 Advanced Menu –H/W Monitor
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
Save
&
PC Health Status
CPU Warning Temperature
CPU Shutdown Temperature
CPU Smart FAN
SYS Manual PWM
[Disabled]
[Disabled]
[Disabled]
255
CPU Temperature
Top Side System Temperature
Bottom Side System Temperature
: +99 C
: +48 C
: +48 C
CPU Fan Speed
: 5050 RPM
+3.3V
+VCORE
+VGFX
+1.05V
+1.5V
+5VDUAL
+12V
+3.3VSB
: +3.296 V
: +1.080 V
: +0.440 V
: +1.048 V
: +1.493 V
: +5.120 V
: +11.792 V
: +3.328 V
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
CPU Warning Temperature
Options: Disabled, 80 C, 85 C, 90 C, 95 C
CPU Shutdown Temperature
Options: Disabled, 80 C, 85 C, 90 C, 95 C
CPU Smart Fan
Options: Disabled, Enabled
KEEX-6100 User’s Manual
51
Exit
Chapter 4
 Boot Menu
Table 59 Boot Menu
BIOS SETUP UTILITY
Main
Advanced
Boot Configuration
Full Screen LOGO Display
Setup Prompt Timeout
Bootup NumLock State
Boot Option Priorities
Boot Option #1
Boot
Security
[Disabled]
1
[On]
[SATA: WDC WD6402AA…]
Hard Drive BBS Priorities
Bootup Numlock State
Options: On, Off
Boot Option #1
Options: SATA: WDC WD6402AAEX-00Z3A0, Disabled
Hard Drive BBS Priorities
Boot Option #1: SATA: Maxtor 6L120M0, Disabled
KEEX-6100 User’s Manual
52
&
Exit
Enables or Disables Quiet Boot
option
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
Full Screen LOGO Display
Options: Disabled, Enabled
Save
Chapter 4
 Security Menu
Table 60 Security Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
Password Description
Save
&
Exit
Set Setup Administrator
Password
If ONLY the Administrator’s password is set, then this only limits access to
Setup and is only asked for when entering Setup
If ONLY the User’s password is set, then this is a power on password and
must be entered to boot or enter Setup. In Setup the User will have
Administrator rights
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
Administrator Password
F1: General Help
User Password
F2: Previous Values
F3: Optimized Defaults
HDD Security Configuration:
F4 Save & Exit
HDD 0: WDC WD6402AA
ESC Exit
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
 Save & Exit Menu
Table 61 Save & Exit Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Save Changes and Exit
Discard Changes and Reset
Save Changes and Reset
Discard Changes and Reset
Security
Save
&
Exit
Exit system setup after saving
the changes.
Save Options
Save Changes
Discard Changes
  Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4 Save & Exit
ESC Exit
Restore Defaults
Save as User Defaults
Restore User Defaults
Boot Override
SATA: WDC WD6402AAEX-00Z3A0
Version 2.10.1208. Copyright (C) 2010, American Megatrends, Inc.
KEEX-6100 User’s Manual
53
Chapter 4
Save Changes and Exit
Exit system setup after saving the changes. Once you are finished making your
selections, choose this option from the Exit menu to ensure the values you selected
are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup
battery and stays on even when the PC is turned off. When you select this option, a
confirmation window appears. Select [Yes] to save changes and exit.
Discard Changes and Exit
Exit system setup without saving any changes. Select this option only if you do not
want to save the changes that you made to the Setup program. If you made changes
to fields other than system date, system time, and password, the BIOS asks for a
confirmation before exiting.
Discard Changes
Discards changes done so far to any of the setup values. This option allows you to
discard the selections you made and restore the previously saved values. After
selecting this option, a confirmation appears. Select [Yes] to discard any changes and
load the previously saved values.
Load Optimal Defaults
Load Optimal Default values for all the setup values. This option allows you to load
optimal default values for each of the parameters on the Setup menus, which will
provide the best performance settings for your system. The F9 key can be used for
this operation.
Load Failsafe Defaults
Load Optimal Default values for all the setup values. This option allows you to load
failsafe default values for each of the parameters on the Setup menus, which will
provide the most stable performance settings. The F8 key can be used for this
operation.
KEEX-6100 User’s Manual
54
Chapter 5
Chapter 5
Driver Installation
If your KEMX-6000 does not come with an operating system pre-installed, you will
need to install an operating system and the necessary drivers to operate it. After you
have finished assembling your system and connected the appropriate power source,
power it up using the power supply and install the desired operating system.
You can download the drivers for the KEEX-6100 from the Quanmax website
at www.quanmax.com and install as instructed there. For other operating systems,
please contact Quanmax.
NOTE
When the system reboots without connecting the CRT, there might be no
image on screen when you insert the CRT/VGA cable. Please
pressing <Ctrl>+<Alt>+<F1> simultaneously to show the image on screen.
KEEX-6100 User’s Manual
55
Appendix A
Appendix A
DIO (Digital I/O) Sample Code
//***************************************************************
//KEEX-6100 DOS DIO sample program
//Please compile with Turbo C 3.0 to utilized the program
//0:Low 1:High
//DI_1: IOport 0x50C bit2 DO_1: IOport 0x539 bit4
//DI_2: IOport 0x50C bit3 DO_2: IOport 0x539 bit5
//DI_3: IOport 0x50C bit4 DO_3: IOport 0x539 bit6
//DI_4: IOport 0x50C bit5 DO_4: IOport 0x53B bit0
//***************************************************************
int main()
{
int RetVal;
//Clear DO_1~4
RetVal=inp(0x539);//IO Port: 0x539
RetVal=(RetVal&0x8F);//DO_1 is bit 4
//DO_2 is bit 5
//DO_3 is bit 6
outp(0x539,RetVal);
RetVal=inp(0x53B);//IO Port: 0x53B
RetVal=(RetVal&0xFE);//DO_4 is bit 0
outp(0x53B,RetVal);
system("pause");
//Setting DO_1~4
RetVal=inp(0x539);//IO Port: 0x539
RetVal=(RetVal|0x70);//DO_1 is bit 4
KEEX-6100 User’s Manual
56
Appendix A
//DO_2 is bit 5
//DO_3 is bit 6
outp(0x539,RetVal);
RetVal=inp(0x53B);//IO Port: 0x53B
RetVal=(RetVal|0x01);//DO_4 is bit 0
outp(0x53B,RetVal);
system("pause");
//Reading DI_1~4
RetVal=inp(0x50C);//IO Port: 0x50C
RetVal=(RetVal&0x3C);//DI_1 is bit 2
//DI_2 is bit 3
//DI_3 is bit 4
//DI_4 is bit 5
printf("DI_= %d\n",RetVal);
system("pause");
return 0;
}
KEEX-6100 User’s Manual
57
Appendix B
Appendix B
WatchDog Timer Sample Code
//============================================
//KEEX-6100 DOS Watchdog sample program
//Please compile with Turbo C 3.0 to utilized the program
//============================================
#include<stdio.h>
int main()
{
int value;
//Initialized the WDT program
outp(0x2E,0x87);
outp(0x2E,0x87);
//Setting Logical Device Number to 0x07
outp(0x2E,0x07);
outp(0x2F,0x07);
//0xF5 bit6
//If watchdog timeout event occurs, this bit will be set to 1.
//Write a 1 to this bit will clear it to 0.
outp(0x2F,0xF5);
value=inp(0x2F);
outp(0x2F,(value | 0x40));
//Set Timer unit
//(0xF5 bit3(0: 1sec, 1: 60 sec) of watchdog timer by setting this bit)
outp(0x2E,0xF5);
value=inp(0x2F);
outp(0x2F,(value & 0xF7));//set unit sec.
//Set Timer Value(0xF6 Time of watchdog timer)
outp(0x2E,0xF6);
outp(0x2F,0x14);//set to 20 sec (0x14)
//Enable WDT
outp(0x2E,0xF5);
value=inp(0x2F);
outp(0x2F,(value | 0x30));//
KEEX-6100 User’s Manual
58
Appendix B
outp(0x2E,0xF0);
outp(0x2F,0x81);//bit7 WDTRST# output is enabled
return 0;
}
KEEX-6100 User’s Manual
59