York 036-048 Installation manual

INSTALLATION
MANUAL
CONTENTS
SUNLINE MAGNUM™
GAS/ELECTRIC SINGLE PACKAGE
AIR CONDITIONERS
DJ 036, 048 & 060
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . 4
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
RENEWAL PARTS. . . . . . . . . . . . . . . . . . . . . . . . . 5
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PRODUCT NOMENCLATURE. . . . . . . . . . . . . . . . 6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
START-UP (COOLING) . . . . . . . . . . . . . . . . . . . . 49
START-UP (GAS HEAT) . . . . . . . . . . . . . . . . . . . 50
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . 53
SEE THE FOLLOWING PAGE FOR A COMPLETE TABLE OF CONTENTS.
NOTES, CAUTIONS AND WARNINGS
The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. Notes are intended to
clarify or make the installation easier. Cautions are given
to prevent equipment damage. Warnings are given to alert
installer that personal injury and/or equipment damage
may result if installation procedure is not handled properly.
CAUTION:
READ ALL SAFETY GUIDES BEFORE YOU
BEGIN TO INSTALL YOUR UNIT.
SAVE THIS MANUAL
362246-YIM-C-0109
362246-YIM-C-0109
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . 4
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
RENEWAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PRODUCT NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INSTALLATION SAFETY INFORMATION: . . . . . . . . . . . 7
LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
RIGGING AND HANDLING . . . . . . . . . . . . . . . . . . . . . . . 8
CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CONDENSATE DRAIN . . . . . . . . . . . . . . . . . . . . . . . . . . 9
COMPRESSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SERVICE ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
POWER AND CONTROL WIRING . . . . . . . . . . . . . . . . 12
OPTIONS/ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . 12
ELECTRIC HEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
GAS HEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
GAS PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
GAS CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
L.P. UNITS, TANKS AND PIPING . . . . . . . . . . . . . . . . . . 15
VENT AND COMBUSTION AIR HOODS . . . . . . . . . . . . 16
ECONOMIZER/MOTORIZED DAMPER AND
RAIN HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
POWER EXHAUST/BAROMETRIC RELIEF DAMPER
AND RAIN HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ECONOMIZER AND POWER EXHAUST DAMPER SET
POINT ADJUSTMENTS AND INFORMATION . . . . . . . 17
MINIMUM POSITION ADJUSTMENT . . . . . . . . . . . . . . . 17
ENTHALPY SET POINT ADJUSTMENT . . . . . . . . . . . . 17
POWER EXHAUST DAMPER SETPOINT (WITH OR
WITHOUT POWER EXHAUST) . . . . . . . . . . . . . . . . . . . 17
INDOOR AIR QUALITY . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LOW AMBIENT COOLING . . . . . . . . . . . . . . . . . . . . . . . 45
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . .
COMPRESSOR PROTECTION . . . . . . . . . . . . . . . . . .
FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRIC HEATING SEQUENCE OF
OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . .
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HEAT ANTICIPATOR SETPOINTS . . . . . . . . . . . . . . .
GAS HEATING SEQUENCE OF OPERATION . . . . . .
45
45
45
45
46
46
46
46
47
TWO STAGE FURNACE ONLY . . . . . . . . . . . . . . . . . . . 47
GAS HEAT OPERATION ERRORS . . . . . . . . . . . . . . . 47
TEMPERATURE LIMITS . . . . . . . . . . . . . . . . . . . . . . . .
GAS VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CENTRIFUGAL SWITCH . . . . . . . . . . . . . . . . . . . . . . . .
ROLLOUT SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FLAME SENSE CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . .
48
48
48
48
48
FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HEAT ANTICIPATOR SETPOINTS . . . . . . . . . . . . . . .
START-UP (COOLING) . . . . . . . . . . . . . . . . . . . . . . . . . .
PRESTART CHECK LIST . . . . . . . . . . . . . . . . . . . . . . .
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . .
POST START CHECK LIST . . . . . . . . . . . . . . . . . . . . .
SHUT DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
START-UP (GAS HEAT) . . . . . . . . . . . . . . . . . . . . . . . . .
PRE-START CHECK LIST . . . . . . . . . . . . . . . . . . . . . .
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . .
49
49
49
49
49
49
49
49
50
50
50
TO LIGHT PILOT AND MAIN BURNERS: . . . . . . . . . . . 50
TO SHUT DOWN: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
POST-START CHECK LIST (GAS) . . . . . . . . . . . . . . . 50
MANIFOLD GAS PRESSURE ADJUSTMENT . . . . . . . 51
PILOT CHECKOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
BURNER INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . 51
BURNER AIR SHUTTER ADJUSTMENT . . . . . . . . . . . 52
CHECKING GAS INPUT . . . . . . . . . . . . . . . . . . . . . . . . 52
NATURAL GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
PHASING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
SUPPLY AIR BLOWERS . . . . . . . . . . . . . . . . . . . . . . . . 42
CHECKING SUPPLY AIR CFM . . . . . . . . . . . . . . . . . . . 42
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
SEQUENCE OF OPERATIONS OVERVIEW . . . . . . . . 43
COOLING SEQUENCE OF OPERATION . . . . . . . . . . . 44
ADJUSTMENT OF TEMPERATURE RISE . . . . . . . . . .
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING TROUBLESHOOTING GUIDE . . . . . . . . . .
CHARGING THE UNIT . . . . . . . . . . . . . . . . . . . . . . . . .
NORMAL OPERATING PRESSURES . . . . . . . . . . . . .
GAS HEAT TROUBLESHOOTING GUIDE . . . . . . . . . .
FLASH CODE TROUBLESHOOTING . . . . . . . . . . . . .
52
53
53
55
56
57
58
CONTINUOUS BLOWER . . . . . . . . . . . . . . . . . . . . . . . . 44
INTERMITTENT BLOWER . . . . . . . . . . . . . . . . . . . . . . . 44
NO OUTDOOR AIR OPTIONS . . . . . . . . . . . . . . . . . . . . 44
ECONOMIZER WITH SINGLE ENTHALPY SENSOR . . 44
ECONOMIZER WITH DUAL ENTHALPY SENSORS . . . 44
ECONOMIZER (SINGLE OR DUAL) WITH POWER
EXHAUST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
MOTORIZED OUTDOOR AIR DAMPERS . . . . . . . . . . . 44
IGNITION CONTROL BOARD . . . . . . . . . . . . . . . . . . . .
CENTRIFUGAL SWITCH . . . . . . . . . . . . . . . . . . . . . . . .
PILOT FLAME LOCKOUT . . . . . . . . . . . . . . . . . . . . . . .
PRIMARY OR AUX TEMPERATURE LIMIT . . . . . . . . . .
ROLLOUT SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNEXPECTED FLAME PRESENCE . . . . . . . . . . . . . . .
GAS VALVE STUCK OFF OR ON . . . . . . . . . . . . . . . . .
FLAME SENSE CIRCUIT FAILURE . . . . . . . . . . . . . . . .
58
58
59
59
59
60
60
60
COOLING OPERATION ERRORS . . . . . . . . . . . . . . . . 44
HIGH-PRESSURE LIMIT SWITCH . . . . . . . . . . . . . . . . . 44
LOW-PRESSURE LIMIT SWITCH . . . . . . . . . . . . . . . . . 44
FREEZESTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2
SYMPTOMATIC TROUBLESHOOTING . . . . . . . . . . . . 60
UNIT FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . 62
FAN ON AND OFF DELAYS . . . . . . . . . . . . . . . . . . . . . 62
Johnson Controls Unitary Products
362246-YIM-C-0109
LIST OF FIGURES
Fig. #
1
2
3
4
5
6
7
8
9
10
11
12
Pg. #
RECOMMENDED DRAIN PIPING . . . . . . . . . . . . . . . 9
COMPRESSOR RESTRAINING BRACKET . . . . . . . 9
TYPICAL FIELD POWER & CONTROL WIRING . . . 11
EXTERNAL SUPPLY CONNECTION EXTERNAL
SHUT-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
BOTTOM SUPPLY CONNECTION EXTERNAL
SHUT-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VENT AND COMBUSTION AIR HOOD . . . . . . . . . . 16
ENTHALPY SETPOINT ADJUSTMENT . . . . . . . . . . 18
HONEYWELL ECONOMIZER CONTROL W7212 . . 18
FOUR AND SIX POINT LOADING . . . . . . . . . . . . . . 19
UNIT DIMENSIONS (3 - 5 TON COOLING ONLY/
ELECTRIC HEAT) FRONT VIEW . . . . . . . . . . . . . . . 33
UNIT DIMENSIONS (3 - 5 TON COOLING/GAS HEAT)
FRONT VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
UNIT WITH ECONOMIZER RAINHOOD . . . . . . . . . 34
Fig. #
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Pg. #
UNIT WITH FIXED OUTDOOR AIR/MOTORIZED
DAMPER RAINHOOD . . . . . . . . . . . . . . . . . . . . . . .
UNIT DIMENSIONS (REAR VIEW) . . . . . . . . . . . . .
DISCONNECT/BLOWER ACCESS LOCATION . . .
BELT ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . .
PRESSURE DROP ACROSS COIL . . . . . . . . . . . . .
GAS VALVE PIPING . . . . . . . . . . . . . . . . . . . . . . . .
TYPICAL SINGLE STAGE GAS VALVES . . . . . . . .
TYPICAL 2 STAGE GAS VALVES . . . . . . . . . . . . . .
PROPER FLAME ADJUSTMENT . . . . . . . . . . . . . .
TYPICAL FLAME APPEARANCE . . . . . . . . . . . . . .
DJ036 OPERATING PRESSURES . . . . . . . . . . . . .
DJ048 OPERATING PRESSURES . . . . . . . . . . . . .
DJ060 OPERATING PRESSURES . . . . . . . . . . . . .
UNIT CONTROL BOARD . . . . . . . . . . . . . . . . . . . . .
35
35
36
42
43
47
50
51
51
52
56
56
57
62
LIST OF TABLES
Tbl. #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Pg. #
UNIT APPLICATION DATA (DJ) . . . . . . . . . . . . . . . . 8
CONTROL WIRE SIZES . . . . . . . . . . . . . . . . . . . . . . 12
ELECTRIC HEATER CFM LIMITATIONS . . . . . . . . 13
GAS HEAT APPLICATION DATA . . . . . . . . . . . . . . 13
GAS PIPE SIZING . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CENTER OF GRAVITY (ALL MODELS) . . . . . . . . . 19
DJ 4 AND 6 POINT LOADS WEIGHT
DISTRIBUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DJ PHYSICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . 20
DJ OPERATING WEIGHTS (LBS.) . . . . . . . . . . . . . 20
ELECTRICAL DATA - DJ036, 048 & 060 DIRECT
DRIVE W/O POWERED CONVENIENCE
OUTLET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE
W/O POWERED CONVENIENCE OUTLET . . . . . . . 23
ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE
HIGH STATIC W/O POWERED CONVENIENCE
OUTLET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ELECTRICAL DATA - DJ036, 048 & 060 DIRECT
DRIVE W/POWERED CONVENIENCE OUTLET . . 27
ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE
WITH POWERED CONVENIENCE OUTLET . . . . . . 29
ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE
HIGH STATIC WITH POWERED CONVENIENCE
OUTLET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ELECTRIC HEAT CORRECTION FACTORS . . . . . 33
VOLTAGE LIMITATIONS . . . . . . . . . . . . . . . . . . . . . 33
UTILITIES ENTRY . . . . . . . . . . . . . . . . . . . . . . . . . . 36
MINIMUM CLEARANCES . . . . . . . . . . . . . . . . . . . . 36
SUPPLY AIR BLOWER PERFORMANCE (DJ036 BELT
DRIVE) - SIDE DUCT APPLICATION . . . . . . . . . . . 37
SUPPLY AIR BLOWER PERFORMANCE (DJ036 BELT
DRIVE) - BOTTOM DUCT APPLICATION . . . . . . . . 37
Johnson Controls Unitary Products
Tbl. #
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Pg. #
SUPPLY AIR BLOWER PERFORMANCE (DJ048 BELT
DRIVE) - SIDE DUCT APPLICATION . . . . . . . . . . . 37
SUPPLY AIR BLOWER PERFORMANCE (DJ048 BELT
DRIVE) - BOTTOM DUCT APPLICATION . . . . . . . . 38
SUPPLY AIR BLOWER PERFORMANCE (DJ060 BELT
DRIVE) - SIDE DUCT APPLICATION . . . . . . . . . . . 38
SUPPLY AIR BLOWER PERFORMANCE (DJ060 BELT
DRIVE) - BOTTOM DUCT APPLICATION . . . . . . . . 38
SUPPLY AIR BLOWER PERFORMANCE (DJ036,
048, & 060 DIRECT DRIVE) SIDE DUCT
APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
SUPPLY AIR BLOWER PERFORMANCE (DJ036,
048, & 060 DIRECT DRIVE) BOTTOM DUCT
APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
BELT DRIVE RPM SELECTION . . . . . . . . . . . . . . . 39
BELT DRIVE BLOWER MOTOR AND DRIVE
DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
STATIC RESISTANCES . . . . . . . . . . . . . . . . . . . . . 40
ELECTRIC HEAT LIMIT CONTROL SETTING . . . . 46
ELECTRIC HEAT ANTICIPATOR SETPOINTS . . . . 47
SINGLE STAGE GAS HEAT LIMIT CONTROL
SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
2 STAGE GAS HEAT LIMIT CONTROL SETTING. . 49
GAS HEAT ANTICIPATOR SETPOINTS . . . . . . . . . 49
GAS RATE - CUBIC FEET PER HOUR . . . . . . . . . . 52
DJ036 COOLING SUPERHEAT CHARGING
TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
DJ048 COOLING SUPERHEAT CHARGING
TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
UNIT CONTROL BOARD FLASH CODES . . . . . . . 63
IGNITION CONTROL BOARD FLASH CODES . . . . 63
3
362246-YIM-C-0109
GENERAL
YORK Model DJ units are either single package cooling units equipped with optional factory installed electric heaters, or single package gas-fired central heating
furnaces with cooling unit. Both are designed for outdoor installation on a rooftop or slab.
The units are completely assembled on rigid, permanently attached base rails. All piping, refrigerant
charge, and electrical wiring is factory installed and
tested. The units require electric power, gas connection, duct connections, installation of combustion air
inlet hood, flue gas outlet hoods and fixed outdoor air
intake damper (units without economizer or motorized
damper option only) at the point of installation.
The supplemental electric heaters have nickel-chrome
elements and utilize single point power connection.
The gas-fired heaters have aluminized-steel (or
optional stainless steel) tubular heat exchangers. The
units have spark ignition with proven pilot. All gas heaters are shipped from the factory equipped for natural
gas use, but can be field converted to L.P./ Propane
with Kit Model # 1NP0440 for single stage and Kit
Model # 1NP0485 for 2 stage.
SAFETY CONSIDERATIONS
Due to system pressure, moving parts and electrical
components, installation and servicing of air conditioning equipment can be hazardous. Only qualified,
trained, service personnel should install, repair, maintain or service this equipment.
Observe all precautions in the literature, on labels and
tags accompanying the equipment whenever working
on air conditioning equipment. Be sure to follow all
other safety precautions that apply.
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury, death, or property damage.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach the gas supplier, call
the fire department.
- Installation and service must be performed by
a qualified installer, service agency or the
gas supplier.
INSPECTION
As soon as a unit is received, it should be inspected for
possible damage during transit. If damage is evident,
the extent of the damage should be noted on the carrier's freight bill. A separate request for inspection by
the carrier's agent should be made in writing.
Wear safety glasses and work gloves, and follow all
safety codes. Use a quenching cloth and have a fire
extinguisher available for all brazing operations.
4
Johnson Controls Unitary Products
362246-YIM-C-0109
REFERENCE
Additional information is available in the following reference forms:
•
Technical Guide - DJ036-060, 282262
•
General Installation - DJ036-060, 362246
This product must be installed in strict compliance with the enclosed installation instructions
and any applicable local, state, and national
codes including, but not limited to, building,
electrical, and mechanical codes.
RENEWAL PARTS
Contact your local York® parts distribution center for
authorized replacement parts.
APPROVALS
Design listed by CSA as follows:
•
For use as a cooling unit only with or without
optional electric heat.
•
For use as a forced air furnace with cooling
unit
•
For outdoor installation only.
•
For installation on combustible material.
•
For use with natural gas or propane gas.
Johnson Controls Unitary Products
Improper installation may create a condition
where the operation of the product could cause
personal injury or property damage.
The installer should pay particular attention to the
words: NOTE, CAUTION and WARNING. Notes are
intended to clarify or make the installation easier. Cautions are given to prevent equipment damage. Warnings are given to alert installer that personal injury and/
or equipment damage may result if installation procedure is not handled properly.
5
362246-YIM-C-0109
PRODUCT NOMENCLATURE
3-5 Ton Sunline Magnum™ Model Number Nomenclature
D J 048 N04 A 2 A AA 2 0 1 2 4 A
Product Category
Product Style
D = A/C, Single Pkg., R-22
A = Style A
Product Identifier
Configuration Options (not required for all units)
These four digits will not be assigned until a quote is requested, or an order placed.
J = 13.0 SEER A/C
SS Drain Pan
CPC Controller, DFS, APS
Johnson Controller UNT 1126 (N2 protocol), DFS, APS
Nominal Cooling Capacity
Honeywell Controller, DFS, APS
036 = 3.0 Ton
048 = 4.0 Ton
060 = 5.0 Ton
Novar Controller, DFS, APS
Simplicity IntelliComfort Controller
Simplicity IntelliComfort Controller w/ModLinc
York Commercial Comfort System (YCCS) Rtu Controller
Heat Type and Nominal Heat Capacity
2" Pleated filters
BAS Ready Economizer (2-10 V.D.C. Actuator without a Controller)
C00 = Cooling Only. Suitable for Field
Installed Electric Heat
Any Combination of Additional Options that Don’t Have an Option Code Pre-assigned
Gas Heat Options
Product Generation
N04 = 40 MBH Output Aluminized Steel, 1 Stage (036)
N06 = 60 MBH Output Aluminized Steel, 1 Stage (048)
N08 = 80 MBH Output Aluminized Steel, 1 Stage
(036, 060)
N10 = 100 MBH Output Aluminized Steel, 1 Stage
(048, 060)
D06 = 60 MBH Output Aluminized Steel, 2 Stage
(036, 048, 060)
D10 = 100 MBH Output Aluminized Steel, 2 Stage
(036*, 048, 060)
S04 = 40 MBH Output Stainless Steel, 1 Stage (036)
S06 = 60 MBH Output Stainless Steel, 1 Stage (048)
S08 = 80 MBH Output Stainless Steel, 1 Stage
(036, 060)
S10 = 100 MBH Output Stainless Steel, 1 Stage
(048, 060)
T06 = 60 MBH Output Stainless Steel, 2 Stage
(036, 048, 060)
T10 = 100 MBH Output Stainless Steel, 2 Stage
(036*, 048, 060)
2 = Second Generation
Additional Options
Standard Cabinet
Hinged Filter Door & Toolless Access Cabinet
AA = None
AB = Phase Monitor
AC = Coil Guard
AD = Dirty Filter Switch
AE = Phase Monitor & Coil Guard
AF = Phase Monitor & Dirty Filter Switch
AG = Coil Guard & Dirty Filter Switch
AH = Phase Monitor, Coil Guard & Dirty Filter Switch
AS = Bottom Drain Connection
RC = Coil Guard & American Flag
TA = Technicoat Condenser Coil
TJ = Technicoat Evaporator Coil
TS = Technicoat Evaporator and Condenser Coil
BA = Hinged Filter Door & Toolless Access Panels
BB = Phase Monitor, Hinged Filter Door & Toolless
Access Panels
BC = Coil Guard, Hinged Filter Door & Toolless
Access Panels
BD = Dirty Filter Switch, Hinged Filter Door &
Toolless Access Panels
BE = Phase Monitor & Coil Guard, Hinged Filter
Door & Toolless Access Panels
BF = Phase Monitor & Dirty Filter Switch, Hinged
Filter Door & Toolless Access Panels
BG = Coil Guard & Dirty Filter Switch, Hinged Filter
Door & Toolless Access Panels
BH = Phase Monitor, Coil Guard & Dirty Filter Switch,
Hinged Filter Door & Toolless Access Panels
Electric Heat Options
E05 = 5 KW
E07 = 7 KW
E10 = 10 KW
E15 = 15 KW
E20 = 20 KW
E30 = 30 KW
ZZ = If desired option combination is not listed above, ZZ will be assigned and configuration options will be
located in digits 15-18.
Installation Options
*(D, T)10 = 92 MBH Output on 036 Models
Airflow
A = Direct Drive
B = Direct Drive/Economizer
D = Direct Drive/Motorized Damper
N = Belt Drive
P = Belt Drive/Economizer
R = Belt Drive/Motorized Damper
T = Belt Drive High Static
U = Belt Drive High Static/Economizer
V = Belt Drive High Static/Motorized Damper
Voltage
1 = 208/230-1-60
2 = 208/230-3-60
4 = 460-3-60
5 = 575-3-60
A = No Options Installed
B = Option 1
C = Option 2
D = Options 1 & 2
E = Option 3
F = Option 4
G = Options 1 & 3
H = Options 1 & 4
J = Options 1, 2 & 3
K = Options 1, 2, & 4
L = Options 1,3 & 4
M = Options 1, 2, 3, & 4
N = Options 2 & 3
P = Options 2 & 4
Q = Options 2, 3, & 4
R = Options 3 & 4
S = Option 5
T = Options 1 & 5
U = Options 1, 3, & 5
V = Options 1, 4, & 5
W = Options 1, 3, 4, & 5
X = Options 3 & 5
Y = Options 4 & 5
Z = Options 3, 4 & 5
Options
1 = Disconnect
2 = Non-Pwr'd Conv. Outlet
3 = Smoke Detector S.A.
4 = Smoke Detector R.A.
5 = Pwr'd Conv. Outlet
6
Johnson Controls Unitary Products
362246-YIM-C-0109
INSTALLATION
In U.S.A.:
INSTALLATION SAFETY INFORMATION:
•
National Electrical Code ANSI/NFPA No. 70.
•
National Fuel Gas Code Z223.1.
•
Gas-Fired Central Furnace Standard ANSI
Z21.47a.
•
Local gas utility requirements.
Read these instructions before continuing this appliance installation. This is an outdoor combination heating and cooling unit. The installer must assure that
these instructions are made available to the consumer
and with instructions to retain them for future reference.
1. Refer to the furnace rating plate for the approved
type of gas for this furnace.
In Canada:
•
Current Canadian Electrical Code C22.1.
2. Install this furnace only in a location and position
as specified on page 8 of these instructions.
•
Current Gas Installation Codes CSA-B149.1.
•
Local plumbing and waste water codes.
3. Never test for gas leaks with an open flame. Use
commercially available soap solution made specifically for the detection of leaks when checking all
connections.
•
Other applicable local codes.
4. Always install furnace to operate within the furnace's
intended temperature-rise range with the duct system and within the allowable external static pressure
range, as specified on the unit name/rating plate.
If components are to be added to a unit to meet local
codes, they are to be installed at the dealer's and/or
the customer's expense.
5. This equipment is not to be used for temporary
heating or cooling of buildings or structures under
construction.
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly
could result in serious injury, death or property
damage.
Never test for gas leaks with an open flame.
use a commercially available soap solution
made specifically for the detection of leaks to
check all connections. A fire or explosion may
result causing property damage, personal
injury or loss of life.
LIMITATIONS
Refer to the Unit Application Data Table 1 and to the
Gas Heat Application Data Table 4.
Size of unit for proposed installation should be based
on heat loss/heat gain calculation made according to
the methods of the Air Conditioning Contractors of
America (ACCA).
The Simplicity® control board used in this
product will effectively operate the cooling system down to 0°F when this product is applied in
a comfort cooling application for people. An
economizer is typically included in this type of
application. When applying this product for process cooling applications (computer rooms,
switchgear, etc.), please reference applications
bulletin AE-011-07 or call the applications
department for Unitary Products @ 1-877UPG-SERV for guidance. Additional accessories may be needed for stable operation at
temperatures below 30° F.
These units must be installed in accordance with the
following national and local safety codes:
Johnson Controls Unitary Products
7
362246-YIM-C-0109
TABLE 1: UNIT APPLICATION DATA (DJ)
UNIT MODEL NUMBER
Voltage Variation,
Min. / Max.1
036
048
187 / 252
432 / 504
540 / 630
060
1200
1600
2000
208/230
460
575
Supply Air CFM, Nom.
Wet Bulb Temperature (ºF) of Air on Evaporator Coil,
Min. / Max
Dry Bulb Temperature (ºF) of Air on Condenser Coil,
Min. / Max.
57 / 72
0 / 125
1. Utilization range “A” in accordance with ARI Standard 110.
Use the following guidelines to select a suitable location for these units.
If a unit is to be installed on a roof curb or special frame
other than a YORK roof curb, gasketing must be
applied to all surfaces that come in contact with the unit
underside.
1. Unit is designed for outdoor installation only.
RIGGING AND HANDLING
LOCATION
2. Condenser coils must have an unlimited supply of air.
3. Where a choice of location is possible, position the
unit on either north or east side of building.
4. For ground level installation, use a level concrete
slab with a minimum thickness of 4 inches. The
length and width should be at least 6 inches
greater than the unit base rails. Do not tie slab to
the building foundation.
5. Roof structures must be able to support the weight
of the unit and its options and/or accessories. Unit
must be installed on a solid level roof curb or
appropriate angle iron frame.
6. Maintain level tolerance to 1/2 inch maximum
across the entire length or width of the unit.
Excessive exposure of this furnace to contaminated combustion air may result in equipment
damage or personal injury. Typical contaminates include: permanent wave solutions, chlorinated waxes and cleaners, chlorine based
swimming pool chemicals, water softening
chemicals, carbon tetrachloride, Halogen type
refrigerants, cleaning solvents (e.g. perchloroethylene), printing inks, paint removers, varnishes, hydrochloric acid, cements and glues,
antistatic fabric softeners for clothes dryers,
masonry acid washing materials.
8
Exercise care when moving the unit. Do not remove
any packaging until the unit is near the place of installation. Rig the unit by attaching chain or cable slings to
the lifting holes provided in the base rails. Spreader
bars, whose length exceeds the largest dimension
across the unit, MUST BE USED.
Units may also be moved or lifted with a forklift. Slotted
openings in the base rails are provided for this purpose. Fork lengths must be a minimum of 42 inches.
Remove the nesting brackets from the four corners on
the top of the unit. All screws that are removed when
removing the brackets must be replaced on the unit.
Refer to Table 9 for unit weights and to the Figure 9 for
approximate center of gravity.
Before lifting a unit, make sure that all panels
are in place and that its weight is distributed
equally on all cables so it will lift evenly.
CLEARANCES
All units require certain clearances for proper operation
and service. Installer must make provisions for adequate combustion and ventilation air in accordance with
Section 5.3, Air for Combustion and Ventilation of the
National Fuel Gas Code, ANSI Z223.1 (in U.S.A.) or
Sections 7.2, 7.3 or 7.4 of Gas Installation Codes CSAB149.1 (in Canada) and/or applicable provisions of the
local building codes. Refer to Dimensions and Clearances shown in Figures 10 through 13 and Tables 18
Johnson Controls Unitary Products
362246-YIM-C-0109
and 19 for the clearances required for combustible construction, servicing, and proper unit operation.
line MUST be trapped to provide proper drainage. See Figure 1.
Do not permit overhanging structures or shrubs
to obstruct outdoor air discharge outlet, combustion air inlet or vent outlets.
DUCTWORK
Ductwork should be designed and sized according to
the methods in Manual Q of the Air Conditioning Contractors of America (ACCA).
A closed return duct system shall be used. This shall
not preclude use of economizers or outdoor fresh air
intake. The supply and return air duct connections at
the unit should be made with flexible joints to minimize
noise.
The supply and return air duct systems should be
designed for the CFM and static requirements of the
job. They should NOT be sized to match the dimensions of the duct connections on the unit.
FIGURE 1 - RECOMMENDED DRAIN PIPING
COMPRESSORS
Units are shipped with compressor mountings factoryadjusted and ready for operation.
Units with scroll compressors have a shipping bracket
which must be removed after the unit is set in place.
See Figure 2.
COMPRESSOR
MOUNTING
BRACKET BASE
When fastening ductwork to side duct flanges
on unit, insert screws through duct flanges only.
DO NOT insert screws through casing. Outdoor
ductwork must be insulated and waterproofed.
REMOVE THESE
SCREWS (2)
MOUNTING
BRACKET TOP
(REMOVE)
Refer to Figures 10 through 14 for information concerning side and bottom supply and return air duct openings.
NOTE: It is recommended that, in Canada, the outlet
duct be provided with a removable access
panel. It is recommended that this opening be
accessible when the unit is installed in service,
and of a size such that smoke or reflected light
may be observed inside the casing to indicate
the presence of leaks in the heat exchanger.
The cover should be attached in a manner
adequate to prevent leakage.
WIRE TIE
(CUT AND
REMOVE)
FIGURE 2 - COMPRESSOR RESTRAINING BRACKET
Do not loosen compressor mounting bolts.
CONDENSATE DRAIN
FILTERS
Plumbing must conform to local codes. Use a sealing
compound on male pipe threads. Install a condensate
drain line from the 3/4” NPT female connection on the
unit to an open drain.
One-inch or two-inch filters can be supplied with each
unit. Filters must always be installed ahead of the
evaporator coil and must be kept clean or replaced with
same size and type. Dirty filters will reduce the capacity
of the unit and will result in frosted coils or safety shutdown. Minimum filter area and required sizes are
shown in Physical Data Table 8.
NOTE: The condensate drain operates in a negative
pressure in the cabinet. The condensate drain
Johnson Controls Unitary Products
9
362246-YIM-C-0109
SERVICE ACCESS
The following removable panels provide access to all
serviceable components:
•
Compressor compartment
•
Electric Heat compartment
•
Gas Heat compartment
•
Blower compartment
•
Main control box
•
Filter compartment
10
Refer to the Dimensions and Clearances shown in Figures 10, 11, 13 and 14 for location of these access
panels.
Make sure that all screws and panel latches
are replaced and properly positioned on the
unit to maintain an airtight seal.
Johnson Controls Unitary Products
362246-YIM-C-0109
TYPICAL POWER WIRING
REFER TO THE ELECTRICAL DATA
TABLES TO SIZE THE DISCONNECT
SWITCH, OVERCURRENT PROTECTION AND WIRING.
TYPICAL CONTROL WIRING
COOLING / HEATING (24 VOLT THERMOSTAT)
COOLING / HEATING (24 VOLT THERMOSTAT)
THERMOSTAT 1
TERMINALS
ADD
JUMPER
THERMOSTAT 1
TERMINALS
RH
UNIT TERMINAL
STRIP TB1
RC
R
Y
Y1
ADD
JUMPER
RH
UNIT TERMINAL
STRIP TB1
RC
R
Y
Y1
24 VOLT
TRANSFORMER
Y2
W
Y2
W1
W
W2
G
C
1
W1
W2
G
G
24 VOLT
TRANSFORMER
G
C
24 VOLT THERMOSTAT 2ET07701024. TO CONTROL THE ECONOMIZER ON THE SECOND
STAGE COOLING OR TO HAVE AN ELECTRIC HEAT ACCESSORY WITH TWO STAGES OF
HEAT, USE THERMOSTAT 2TH0471024.
1
24 VOLT THERMOSTAT 2ET07701024. TO CONTROL THE ECONOMIZER ON THE SECOND
STAGE COOLING OR TO HAVE AN ELECTRIC HEAT ACCESSORY WITH TWO STAGES OF
HEAT, USE THERMOSTAT 2TH0471024.
COOLING / HEATING (ELECTRONIC THERMOSTAT)
MULTI STAGE
THERMOSTAT1
TERMINALS
UNIT TERMINAL
STRIP TB1
RC
ADD
JUMPER
RH
R
Y1
Y1
2
Y2
3
G
B
C
COM
X
NOT
USED
ADD
JUMPER
OCC
4
T
TO REMOTE SENSOR
2TH040702224 IF USED
ELECTRONIC PROGRAMMABLE THERMOSTAT 2ET04700224 (INCLUDES SUBBASE).
2
SECOND STAGE COOLING IS NOT REQUIRED ON UNITS LESS ECONOMIZER.
3
SECOND STAGE HEATING IS ONLY REQUIRED ON UNITS WITH A TWO STAGE
ELECTRIC HEATER OR TWO STAGE GAS HEAT.
RC
R
Y
Y1
W
W1
G
G
24 VOLT
TRANSFORMER
A2
1
UNIT TERMINAL
STRIP TB1
C
A1
T
4
RH
W2
G
LED 1
ADD
JUMPER
THERMOSTAT1
TERMINALS
W1
W2
LED 2
COOLING / HEATING (ELECTRONIC THERMOSTAT)
SINGLE STAGE
Y2
W1
4
24 VOLT
TRANSFORMER
1 ELECTRONIC
PROGRAMMABLE THERMOSTAT 2ET07701024 (INCLUDES SUBBASE).
TO CONTROL THE ECONOMIZER ON SECOND STAGE COOLING, USE THERMOSTAT
2TH04700224.
REMOVE JUMPER J2 FROM TERMINALS 4 AND 9 ON JUMPER PLUG CONNECTOR
P6 ON UNITS WITH ECONOMIZER. TERMINALS A1 AND A2 PROVIDE A RELAY
OUT-PUT TO CLOSE THE OUTDOOR ECONOMIZER DAMPERS WHEN THE
THERMOSTAT SWITCHES TO THE SET-BACK POSITION.
FIGURE 3 - TYPICAL FIELD POWER & CONTROL WIRING
Johnson Controls Unitary Products
11
362246-YIM-C-0109
THERMOSTAT
The room thermostat should be located on an inside
wall approximately 56 inches above the floor where it
will not be subject to drafts, sun exposure or heat from
electrical fixtures or appliances. Follow the manufacturer's instructions enclosed with the thermostat for
general installation procedure. A minimum of seven
color-coded insulated wires (#18 AWG) should be used
to connect the thermostat to the unit.
POWER AND CONTROL WIRING
Field wiring to the unit must conform to provisions of
the National Electrical Code, ANSI / NFPA No. 70 (in
U.S.A.), current Canadian Electrical Code C22.1 (in
Canada) and/or local ordinances. The unit must be
electrically grounded in accordance with NEC and CEC
(as specified above) and/or local codes. Voltage tolerances, which must be maintained at the compressor
terminals, during starting and running conditions, are
indicated on the unit Rating Plate and the Unit Application Data table.
The internal wiring harness furnished with this unit is
an integral part of a CSA design certified unit. Field
alteration to comply with electrical codes should not be
required.
Use copper conductors properly sized to carry the load.
Each unit must be wired with a separate branch circuit
fed directly from the meter panel and properly fused.
When connecting electrical power and control
wiring to the unit, waterproof type connectors
MUST BE USED so that water or moisture
cannot be drawn into the unit during normal
operation. The above waterproofing conditions
will also apply when installing a field-supplied
disconnect switch.
Refer to the Typical Field Wiring Figure 3 and to the
appropriate unit wiring diagram for control circuit and
power wiring information.
TABLE 2: CONTROL WIRE SIZES
Wire Size
Maximum Length1
18 AWG
150 Feet
1. From the unit to the thermostat and back to the unit.
OPTIONS/ACCESSORIES
ELECTRIC HEAT
208/230-3-60 and 380/415-3-50 units control
transformers are factory wired for 230v and
415v power supply respectively. Change tap
on transformer for 208-3-60 or 380-3-50 operation. See unit wiring diagram.
A fused disconnect switch should be field provided for
the unit. The switch must be separate from all other circuits. Wire entry at knockout openings require conduit
fittings to comply with NEC (in U.S.A.), CEC (in Canada) and/or local codes. If any of the wire supplied with
the unit must be replaced, replacement wire must be of
the type shown on the wiring diagram and the same
minimum gauge as the replaced wire.
12
The factory- or field-installed heaters are wired for single point power supply. Power supply need only be
brought into the single point terminal block and thermostat wiring to the low voltage terminal strip located in
the upper portion of the unit control box.
These CSA approved heaters are located within the
central compartment of the unit with the heater elements extending into the supply air chamber. Refer to
Figure 10 for access panel location.
Fuses are supplied, where required, by the factory.
Some KW sizes require fuses and others do not. Refer
to Table 3 for minimum CFM limitations and to Tables
10 and 17 for electrical data.
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 3: ELECTRIC HEATER CFM LIMITATIONS
Minimum Supply Air (CFM)
Size
(Tons)
Voltage
3
4
5
Heater kW
5
7
10
15
20
30
208/230-1-60
900
900
900
900
900
-
208/230-3-60
900
900
900
900
900
-
460-3-60
-
900
900
900
900
-
600-3-60
-
-
900
900
900
-
208/230-1-60
1200
1200
1200
1200
1200
-
208/230-3-60
1200
1200
1200
1200
1200
-
460-3-60
-
1200
1200
1200
1200
-
600-3-60
-
-
1200
1200
1200
-
208/230-1-60
1500
1500
1500
1500
1500
1500
208/230-3-60
1500
1500
1500
1500
1500
1500
460-3-60
-
1500
1500
1500
1500
1500
600-3-60
-
-
1500
1500
1500
1500
GAS HEAT
These gas-fired heaters have aluminized-steel or
optional stainless steel, tubular heat exchangers with
spark ignition with proven pilot.
All gas heaters are shipped from the factory equipped
for natural gas use. See Gas Heat Application Data
Table.
For natural gas heating installations in locations requiring low NOx emissions, Accessory model 1LN0406
must be used.
TABLE 4: GAS HEAT APPLICATION DATA
TEMPERATURE RISE °F AT FULL INPUT2
GAS HEAT
OPTION
INPUT
CAPACITY
(MBH)
OUTPUT
CAPACITY
(MBH)
N04
50
40
3 TON
47
15
45
N06
75
60
4 TON
70
25
70
N08
100
80
3/5/6 TON
93
45/25/25
75/55/55
N10
125
100
4/5/6 TON
116
45/35/30
75/75/75
AVAILABLE
ON MODELS
GAS RATE1
(FT3/HR)
MIN.
MAX.
D06
75
61
3/4/5/6 TON
70
35/25/20/15
70/70/55/45
D10
115
92
3 TON
107
55
90
D10
125
101
4/5/6 TON
116
45/35/30
75/75/75
NOTE: Gas Heaters are shipped available for natural gas, but can be converted to L.P. with Kit Model No. 1NP0440 or 1NP0485 (2
Stage). All furnaces meet the latest California seasonal efficiency requirements.
1. Based on 1075 Btu/Ft3.
2. The air flow must be adjusted to obtain a temperature rise within the range shown.
Johnson Controls Unitary Products
13
362246-YIM-C-0109
GAS PIPING
Proper sizing of gas piping depends on the cubic feet
per hour of gas flow required, specific gravity of the gas
and the length of run. “National Fuel Gas Code” Z223.1
(in U.S.A.) or the current Gas Installation Codes CSAB149.1 (in Canada) should be followed in all cases
unless superseded by local codes or gas utility requirements. Refer to the Pipe Sizing Table 5.
Two grommets are shipped in the blower compartment
(in parts bag taped to the blower housing) of every unit
with gas heat and should be used in the knockouts
when the gas piping penetrates the front of the unit.
After the gas supply piping has been installed, the bottom opening in the unit should be sealed to prevent
water from leaking into the building.
Gas piping recommendations:
The heating value of the gas may differ with locality.
The value should be checked with the local gas utility.
1. A drip leg and a ground joint union must be
installed in the gas piping.
NOTE: There may be a local gas utility requirement
specifying a minimum diameter for gas piping.
All units require a 1/2” pipe connection at the
entrance fitting.
3. Use wrought iron or steel pipe for all gas lines. Pipe
compound should be applied sparingly to male
threads only.
TABLE 5: GAS PIPE SIZING
NOMINAL IRON PIPE SIZE
LENGTH IN
FEET
1/2 in.
3/4 in.
1 in.
1-1/4 in.
10
132
278
520
1,050
20
92
190
350
730
30
73
152
285
590
40
63
130
245
500
50
56
115
215
440
60
50
105
195
400
70
46
96
180
370
80
43
90
170
350
90
40
84
160
320
100
38
79
150
305
Maximum capacity of pipe in cubic feet of gas per hour. (Based upon
a pressure drop of 0.3 inch water column and 0.6 specific gravity gas).
GAS CONNECTION
The gas supply line can be routed through the knockouts located on the front of the unit or through the
opening provided in the unit's base. Refer to Figure 11
to locate these access openings. Typical supply piping
arrangements are shown in Figures 4 and 5. All
shaded items are field-supplied.
If gas supply line is routed through the unit's base
ensure that the burner assembly can be removed for
maintenance without disturbing the supply line. The supply piping and fittings must lie below the bottom gas
manifold to avoid interference with the burner assembly.
14
2. When required by local codes, a manual shut-off
valve may have to be installed outside of the unit.
Natural gas may contain some propane. Propane, being an excellent solvent, will quickly
dissolve white lead or most standard commercial compounds. Therefore, a special pipe
compound must be applied when wrought iron
or steel pipe is used. Shellac base compounds
such as Gaskolac or Stalastic, and compounds
such as Rectorseal #5, Clyde's or John Crane
may be used.
4. All piping should be cleaned of dirt and scale by
hammering on the outside of the pipe and blowing
out the loose dirt and scale. Before initial start-up,
be sure that all of the gas lines external to the unit
have been purged of air.
5. The gas supply should be a separate line and
installed in accordance with all safety codes as
prescribed under “Limitations”. After the gas connections have been completed, open the main
shut-off valve admitting normal gas pressure to the
mains. Check all joints for leaks with soap solution
or other material suitable for the purpose. NEVER
USE A FLAME.
Johnson Controls Unitary Products
362246-YIM-C-0109
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly
could result in serious injury, death or property
damage.
Never test for gas leaks with an open flame.
use a commercially available soap solution
made specifically for the detection of leaks to
check all connections. A fire or explosion may
result causing property damage, personal
injury or loss of life.
6. The furnace and its individual manual shut-off
valve must be disconnected from the gas supply
piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig
(3.48kPa).
The furnace must be isolated from the gas supply
piping system by closing its individual manual shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than 1/2 psig (3.48kPa).
7. A 1/8 inch NPT plugged tap, accessible for test
gage connection, must be installed immediately
upstream of the gas supply connection to the furnace.
FIGURE 5 - BOTTOM SUPPLY CONNECTION
EXTERNAL SHUT-OFF
L.P. UNITS, TANKS AND PIPING
All gas heat units are shipped from the factory
equipped for natural gas use only. The unit may be
converted in the field for use with L.P./propane gas
with accessory kit model number 1NP0440 or
1NP0485 (2 Stage).
All L.P./propane gas equipment must conform to the
safety standards of the National Fire Protection Association.
For satisfactory operation, adequate L.P./propane gas
pressure must be provided at the unit manifold under
full load. Maintaining proper gas pressure depends on
three main factors:
1. The vaporization rate depends on (a) the temperature of the liquid and (b) the “wetted surface” area
of the container or containers.
2. The proper pressure regulation. (Two-stage regulation is recommended from the standpoint of both
cost and efficiency.)
3. The pressure drop in the lines between regulators
and between the second stage regulator and the
appliance. Pipe size required will depend on the
length of the pipe run and the total load of all appliances.
FIGURE 4 - EXTERNAL SUPPLY CONNECTION
EXTERNAL SHUT-OFF
Complete information regarding tank sizing for vaporization, recommended regulator settings, and pipe sizing is available from most regulator manufacturers and
L.P./propane gas suppliers.
L.P./propane gas is an excellent solvent and special
pipe compound must be used when assembling piping
Johnson Controls Unitary Products
15
362246-YIM-C-0109
for this gas as it will quickly dissolve white lead or most
standard commercial compounds. Shellac base compounds such as Rectorseal #5 are satisfactory for this
type of gas.
Check all connections for leaks when piping is completed, using a soap solution. NEVER USE A FLAME.
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly
could result in serious injury, death or property
damage.
Never test for gas leaks with an open flame.
use a commercially available soap solution
made specifically for the detection of leaks to
check all connections. A fire or explosion may
result causing property damage, personal
injury or loss of life.
VENT AND COMBUSTION AIR HOODS
The vent hood and combustion air hood (with screens)
are shipped attached to the blower housing in the
blower compartment. These hoods must be installed to
assure proper unit function. All hoods must be fastened
to the outside of the gas heat access panel with the
screws provided in the bag also attached to the blower
housing.
The screen for the combustion air intake hood is
secured to the inside of the access panel opening with
three fasteners and the screws used for mounting the
hood to the panel. The top flange of this hood slips in
under the top of the access panel opening when installing. Refer to Vent and Combustion Air Hood Figure 6.
The vent hood is installed by inserting the top flange of
the hood into the slotted opening in the access panel
and securing in place.
The products of combustion are discharged horizontally through this screened, hooded vent opening on
the gas heat access panel.
16
FIGURE 6 - VENT AND COMBUSTION AIR HOOD
An adhesive backed label is provided over the
outside of the combustion air inlet opening to
prevent moisture from entering the unit, which
could cause damage to electrical components.
Allow this closure label to remain in place until
the combustion air hood is to be installed.
ECONOMIZER/MOTORIZED DAMPER AND RAIN
HOOD
The instruction for the optional economizer/motorized
damper and rain hood can be found in form 03507364-000. Use these instructions when field assembling an economizer rain hood onto a unit. The outdoor
and return air dampers, the damper actuator, the
damper linkage, the outdoor and return air divider baffles, and all the control sensors are factory mounted as
part of the “Factory installed” economizer/motorized
damper options.
POWER EXHAUST/BAROMETRIC RELIEF DAMPER
AND RAIN HOOD
The instructions for the power exhaust/barometric relief
damper and rain hood can be found in form 530.18N1.10V.
All of the components, including the dampers, hardware, and mounting instructions are shipped in a single
package external from the unit and must be field
assembled and installed.
Johnson Controls Unitary Products
362246-YIM-C-0109
Power exhaust is only available as a field installed
accessory.
ECONOMIZER AND POWER EXHAUST DAMPER
SET POINT ADJUSTMENTS AND INFORMATION
Remove the economizer access panel from the unit.
Loosen but do not remove the two panel latches.
Locate the economizer control module, where the following adjustments will be made.
Extreme care must be excercised in turning all
setpoint, maximium, and minimum damper
positioning adjustment screws to prevent twisting them off.
Check that the damper blades move smoothly without
binding; carefully turn the Minimum Position Adjusting
screw (found on the damper control module) fully
clockwise and then set the thermostat indoor fan switch
to the on position and then off, or energize and deenergize terminals “R” to “G”.
MINIMUM POSITION ADJUSTMENT
With thermostat set to indoor fan on position, or terminals “R” to “G” energized, turn the Minimum Position
Adjusting screw (located on the damper control module) counterclockwise until the desired minimum
damper position has been attained.
ENTHALPY SET POINT ADJUSTMENT
The enthalpy set point may now be set by selecting the
desired setpoint shown in the Enthalpy Setpoint Adjustment Figure 7. Adjust as follows:
•
For a single enthalpy operation carefully turn
the set point adjusting screw (found on the
damper control module) to the “A”, “B”, “C” or
“D” setting corresponding to the lettered curve
of the Enthalpy Setpoint Adjustment Figure 7.
Johnson Controls Unitary Products
•
For a dual enthalpy operation, carefully turn
the set point adjusting screw fully clockwise
past the “D” setting.
POWER EXHAUST DAMPER SETPOINT (WITH OR WITHOUT POWER EXHAUST)
•
With no power exhaust option, adjust the
Exhaust Air Adjustment Screw fully clockwise.
•
With power exhaust option, each building pressurization requirement will be different. The
point at which the power exhaust comes on is
determined by the economizer damper position
(Percent Open). The Exhaust Air Adjustment
Screw should be set at the Percent Open of
the economizer damper at which the power
exhaust is needed. It can be set from 0 to
100% damper open.
INDOOR AIR QUALITY
Indoor Air quality (indoor sensor input): Terminal AQ
accepts a +2 to +10 Vdc signal with respect to the
(AQ1) terminal. When the signal is below it's setpoint,
the actuator is allowed to modulate normally in accordance with the enthalpy and mixed air sensor inputs.
When the AQ signal exceeds it's setpoint setting and
there is no call for free cooling, the actuator is proportionately modulated from the 2 to 10 Vdc signal, with 2
Vdc corresponding to full closed and 10 Vdc corresponding to full open. When there is no call for free
cooling, the damper position is limited by the IAQ Max
damper position setting. When the signal exceeds it's
setpoint (Demand Control Ventilation Setpoint) setting
and there is a call for free cooling, the actuator modulates from the minimum position to the full open position based on the highest call from either the mixed air
sensor input or the AQ voltage input.
•
Optional CO2 Space Sensor Kit Part #
2AQ04700324
•
Optional CO2 Unit Sensor Kit Part #
2AQ04700424
Replace the economizer access panel.
17
362246-YIM-C-0109
CONTROL
CURVE
CONTROL POINT
APPROX. 0F (0C)
AT 50% RH
A
73 (23)
B
C
70 (21)
67 (19)
D
63 (17)
85 90 95 100 105 110
(29) (32) (35) (38) (41) (43)
80
(27)
75
(24)
70
(21)
65
(18)
60
(16)
55
(13)
50
(10)
45
(7)
35
(2)
A
B
C
D
40
(4)
B
D C
35
(2)
40 45
(4) (7)
A
50 55 60 65 70 75 80 85 90 95 100 105 110
(10) (13) (16) (18) (21) (24) (27) (29) (32) (35) (38) (41) (43)
APPROXIMATE DRY BULB TEMPERATURE - 0F (0C)
FIGURE 7 - ENTHALPY SETPOINT ADJUSTMENT
Exhaust Air
Adjustment
Screw
Exhaust Air LED
Damper Min.
Position
Screw
Indoor Air Quality
Max. Adjustment
Screw
N1
N
EXH
Set
TR
P1
P
EXH
24
Vac
HOT
T1
T
Min
Pos
IAQ
Max
Indoor Air Quality
LED
AQ1
AQ
IAQ
SO
IAQ
Min
TR1
24
Vac
COM
+
1
2
5
Indoor Air Quality
Min. Adjustment
Screw
Free Cooling LED
SO+
3
4
EF
EF1
Free
Cool
SR+
SR
B
A
C
D
Economizer Enthalpy
Set Point Adjustment
Screw
FIGURE 8 - HONEYWELL ECONOMIZER CONTROL W7212
18
Johnson Controls Unitary Products
362246-YIM-C-0109
BACK OF UNIT
A
447/8
BACK OF UNIT
A
447/8
821/4
821/4
D
B
F
X
X
B
APPROXIMATE
CENTER OF GRAVITY
CONDENSER COIL
END OF UNIT
C
Y
FRONT OF UNIT
C
E
APPROXIMATE
CENTER OF GRAVITY
CONDENSER COIL
END OF UNIT
D
Y
FRONT OF UNIT
FIGURE 9 - FOUR AND SIX POINT LOADING
TABLE 6: CENTER OF GRAVITY (ALL MODELS)
DIMENSION
DJ 036-060
X
40
Y
20
TABLE 7: DJ 4 AND 6 POINT LOADS WEIGHT DISTRIBUTION
UNIT
TOTAL
4-Point Loading (lb)
6-Point Loading (lb)
A
B
C
D
A
B
C
D
E
F
DJ036 Cooling/ Electric
575
132
125
155
164
89
85
82
102
106
110
DJ036N04
615
141
133
166
175
95
91
88
110
114
118
DJ036D06
625
143
135
168
178
96
93
89
111
115
120
DJ036N08
635
145
138
171
181
98
94
91
113
117
122
DJ036D10
645
148
140
174
184
99
96
92
115
119
124
DJ048 Cooling/ Electric
585
134
127
158
167
90
87
84
104
108
112
DJ048(D,N)06
635
145
138
171
181
98
94
91
113
117
122
DJ048(D,N)10
655
150
142
177
187
101
97
94
117
121
125
DJ060 Cooling/ Electric
590
135
128
159
168
91
88
84
105
109
113
DJ060D06
640
147
139
173
182
99
95
92
114
118
123
DJ060N08
650
149
141
175
185
100
97
93
116
120
125
DJ060(D,N)10
660
151
143
178
188
102
98
95
118
122
126
Johnson Controls Unitary Products
19
362246-YIM-C-0109
TABLE 8: DJ PHYSICAL DATA
DJ
MODELS
Centrifugal Blower (Dia. x Wd. in.)
048
060
12 X 10
12 X 10
12 X 10
Fan Motor HP (Direct Drive)
3/4
1
1
Fan Motor HP (Belt Drive)
1 1/2
1 1/2
1 1/2
Fan Motor HP (Belt Drive High Static)
1 1/2
1 1/2
2
Rows Deep
3
4
4
Fins Per Inch
13
13
13
Face Area (Ft.2)
5.1
5.1
5.1
Propeller Dia. (in.)
24
24
24
Fan Motor HP
1/2
1/2
1/2
4200
EVAPORATOR
BLOWER
EVAPORATOR
COIL
CONDENSER
FANS
Nom. CFM
4200
4200
Rows Deep
2
2
2
Fins Per Inch
18
18
18
Face Area (Ft.2)
17.1
17.1
17.1
Quantity
1
1
1
Type
Recip.
Recip.
Scroll
Quantity Per Unit (15” X 20” X 1” or 2“)
2
2
2
Quantity Per Unit (14” X 25” X 1” or 2“)
1
1
1
Total Face Area (Ft.2)
6.3
6.3
6.3
Refrigerant 22 (lbs./oz.)
9/4
9/8
11/8
CONDENSER
COILS
COMPRESSOR
AIR
FILTERS
036
CHARGE
TABLE 9: DJ OPERATING WEIGHTS (LBS.)
MODEL SIZE
3 TON
4 TON
5 TON
575
585
590
N04
615
-
-
N06
-
635
-
N08
635
-
650
N10
-
655
660
D06
625
635
640
D10
645
655
660
DJ (Cooling Only)
BASIC
UNIT
DJ
(Gas/Electric)
Economizer
50
Motorized Damper
OPTIONS
Electric Heater
ACCY.
20
26
5 - 7 kW
18
10 - 15 kW
23
20 - 30 kW
28
Roof Curb
92
Barometric Relief / Fixed Air Damper
10
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 10:ELECTRICAL DATA - DJ036, 048 & 060 DIRECT DRIVE W/O POWERED CONVENIENCE OUTLET
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 11.3
68.0
17.5
2.3
6.0
0.0
230-1-60 11.3
68.0
17.5
2.3
6.0
0.0
208-3-60 8.3
68.0
13.0
2.3
6.0
0.0
230-3-60 8.3
68.0
13.0
2.3
6.0
0.0
208-1-60 15.4
86.0
24.0
2.3
7.6
0.0
230-1-60 15.4
86.0
24.0
2.3
7.6
0.0
208-3-60 11.5
84.0
18.0
2.3
7.6
0.0
230-3-60 11.5
84.0
18.0
2.3
7.6
0.0
036
(3.0)
048
(4.0)
Johnson Controls Unitary Products
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
22.4
31.5
41.2
55.6
79.0
103.1
22.4
35.1
46.6
62.7
90.3
117.9
18.7
21.4
26.9
35.3
48.8
62.7
18.7
23.4
30.1
39.4
55.3
71.2
29.1
33.5
43.2
57.6
81.0
105.1
29.1
37.1
48.6
64.7
92.3
119.9
24.3
24.3
28.9
37.3
50.8
64.7
24.3
25.4
32.1
41.4
57.3
73.2
Max
Fuse2/
Breaker3
Size
(Amps)
30
35
45
60
80
110
30
40
50
70
100
125
25
25
30
40
50
70
25
25
35
40
60
80
35
40
45
60
90
110
35
40
50
70
100
125
30
30
35
40
60
70
30
35
35
45
60
80
21
362246-YIM-C-0109
TABLE 10:ELECTRICAL DATA - DJ036, 048 & 060 DIRECT DRIVE W/O POWERED CONVENIENCE OUTLET (CONT)
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 28.8 145.0 45.0
2.3
7.6
0.0
230-1-60 28.8 145.0 45.0
2.3
7.6
0.0
208-3-60 17.3 123.0 27.0
2.3
7.6
0.0
230-3-60 17.3 123.0 27.5
2.3
7.6
0.0
060
(5.0)
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
19.2
26.9
38.5
57.2
76.4
106.7
23.0
32.6
46.1
69.1
92.2
128.7
11.1
15.5
22.2
33.0
44.1
61.6
13.3
18.8
26.6
39.9
53.2
74.3
45.9
45.9
45.9
57.6
81.0
105.1
142.9
45.9
45.9
48.6
64.7
92.3
119.9
163.7
31.5
31.5
31.5
37.3
50.8
64.7
86.5
31.5
31.5
32.1
41.4
57.3
73.2
98.5
Max
Fuse2/
Breaker3
Size
(Amps)
50
50
50
60
90
110
150
50
50
50
70
100
125
175
35
35
35
40
60
70
90
35
35
35
45
60
80
100
1. Minimum Circuit Ampacity.
2. Dual Element, Time Delay Type.
3. HACR type per NEC.
22
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 11: ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE W/O POWERED CONVENIENCE OUTLET
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 11.3
68.0
17.5
2.3
7.6
0.0
230-1-60 11.3
68.0
17.5
2.3
7.6
0.0
208-3-60 8.3
68.0
13.0
2.3
5.2
0.0
230-3-60 8.3
68.0
13.0
2.3
5.2
0.0
460-3-60 5.1
34.0
8.0
1.3
2.6
0.0
575-3-60 3.2
26.0
5.0
1.3
2.0
0.0
208-1-60 15.4
86.0
24.0
2.3
7.6
0.0
230-1-60 15.4
86.0
24.0
2.3
7.6
0.0
208-3-60 11.5
84.0
18.0
2.3
5.2
0.0
230-3-60 11.5
84.0
18.0
2.3
5.2
0.0
460-3-60 5.8
42.0
9.0
1.3
2.6
0.0
575-3-60 5.1
34.0
8.0
1.3
2.0
0.0
036
(3.0)
048
(4.0)
Johnson Controls Unitary Products
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E07
E10
E15
E20
None
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E07
E10
E15
E20
None
E10
E15
E20
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
6.8
10.1
13.6
19.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
6.8
10.1
13.6
19.5
10.6
15.9
21.2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
2
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
8.5
12.7
17.1
24.5
10.6
16.0
21.3
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
8.5
12.7
17.1
24.5
10.6
16.0
21.3
24.0
33.5
43.2
57.6
81.0
105.1
24.0
37.1
48.6
64.7
92.3
119.9
17.9
20.4
25.9
34.3
47.8
61.7
17.9
22.4
29.1
38.4
54.3
70.2
10.3
13.5
18.4
23.7
32.6
7.0
15.2
21.6
28.0
29.1
33.5
43.2
57.6
81.0
105.1
29.1
37.1
48.6
64.7
92.3
119.9
21.9
21.9
25.9
34.3
47.8
61.7
21.9
22.4
29.1
38.4
54.3
70.2
11.1
13.5
18.4
23.7
32.6
9.4
15.2
21.6
28.0
Max
Fuse2/
Breaker3
Size
(Amps)
30
35
45
60
90
110
30
40
50
70
100
125
25
25
30
35
50
70
25
25
30
40
60
80
15
15
20
25
35
15
20
25
30
35
40
45
60
90
110
35
40
50
70
100
125
30
30
30
35
50
70
30
30
30
40
60
80
15
15
20
25
35
15
20
25
30
23
362246-YIM-C-0109
TABLE 11: ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE W/O POWERED CONVENIENCE OUTLET (CONT)
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 28.8 145.0 45.0
2.3
7.6
0.0
230-1-60 28.8 145.0 45.0
2.3
7.6
0.0
208-3-60 17.3 123.0 27.0
2.3
5.2
0.0
230-3-60 17.3 123.0 27.0
2.3
5.2
0.0
460-3-60 9.6
70.0
15.0
1.3
2.6
0.0
575-3-60 7.4
53.0
11.5
1.3
2.0
0.0
060
(5.0)
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E07
E10
E15
E20
E30
None
E10
E15
E20
E30
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
6.8
10.1
13.6
19.5
28.8
10.6
15.9
21.2
30.4
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
1
1
2
2
2
1
1
2
2
19.2
26.9
38.5
57.2
76.4
106.7
23.0
32.6
46.1
69.1
92.2
128.7
11.1
15.5
22.2
33.0
44.1
61.6
13.3
18.8
26.6
39.9
53.2
74.3
8.5
12.7
17.1
24.5
36.1
10.6
16.0
21.3
30.5
45.9
45.9
45.9
57.6
81.0
105.1
142.9
45.9
45.9
48.6
64.7
92.3
119.9
163.7
29.1
29.1
29.1
34.3
47.8
61.7
83.5
29.1
29.1
29.1
38.4
54.3
70.2
95.5
15.9
15.9
18.4
23.7
32.6
46.6
12.3
15.2
21.6
28.0
39.1
Max
Fuse2/
Breaker3
Size
(Amps)
50
50
50
60
90
110
150
50
50
50
70
100
125
175
30
30
30
35
50
70
90
30
30
30
40
60
80
100
20
20
20
25
35
50
15
20
25
30
40
1. Minimum Circuit Ampacity.
2. Dual Element, Time Delay Type.
3. HACR type per NEC.
24
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 12:ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE HIGH STATIC W/O POWERED CONVENIENCE
OUTLET
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 11.3
68.0
17.5
2.3
7.6
0.0
230-1-60 11.3
68.0
17.5
2.3
7.6
0.0
208-3-60 8.3
68.0
13.0
2.3
5.2
0.0
230-3-60 8.3
68.0
13.0
2.3
5.2
0.0
460-3-60 5.1
34.0
8.0
1.3
2.6
0.0
575-3-60 3.2
26.0
5.0
1.3
2.0
0.0
208-1-60 15.4
86.0
24.0
2.3
7.6
0.0
230-1-60 15.4
86.0
24.0
2.3
7.6
0.0
208-3-60 11.5
84.0
18.0
2.3
5.2
0.0
230-3-60 11.5
84.0
18.0
2.3
5.2
0.0
460-3-60 5.8
42.0
9.0
1.3
2.6
0.0
575-3-60 5.1
34.0
8.0
1.3
2.0
0.0
036
(3.0)
048
(4.0)
Johnson Controls Unitary Products
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E07
E10
E15
E20
None
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E07
E10
E15
E20
None
E10
E15
E20
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
6.8
10.1
13.6
19.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
6.8
10.1
13.6
19.5
10.6
15.9
21.2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
2
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
8.5
12.7
17.1
24.5
10.6
16.0
21.3
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
8.5
12.7
17.1
24.5
10.6
16.0
21.3
24.0
33.5
43.2
57.6
81.0
105.1
24.0
37.1
48.6
64.7
92.3
119.9
17.9
20.4
25.9
34.3
47.8
61.7
17.9
22.4
29.1
38.4
54.3
70.2
10.3
13.5
18.4
23.7
32.6
7.0
15.2
21.6
28.0
29.1
33.5
43.2
57.6
81.0
105.1
29.1
37.1
48.6
64.7
92.3
119.9
21.9
21.9
25.9
34.3
47.8
61.7
21.9
22.4
29.1
38.4
54.3
70.2
11.1
13.5
18.4
23.7
32.6
9.4
15.2
21.6
28.0
Max
Fuse2/
Breaker3
Size
(Amps)
30
35
45
60
90
110
30
40
50
70
100
125
25
25
30
35
50
70
25
25
30
40
60
80
15
15
20
25
35
15
20
25
30
35
40
45
60
90
110
35
40
50
70
100
125
30
30
30
35
50
70
30
30
30
40
60
80
15
15
20
25
35
15
20
25
30
25
362246-YIM-C-0109
TABLE 12:ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE HIGH STATIC W/O POWERED CONVENIENCE
OUTLET (CONT)
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-3-60 17.3 123.0 27.0
2.3
8.2
0.0
230-3-60 17.3 123.0 27.0
2.3
8.2
0.0
460-3-60 9.6
70.0
15.0
1.3
4.1
0.0
575-3-60 7.4
53.0
11.5
1.3
3.6
0.0
060
(5.0)
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E07
E10
E15
E20
E30
None
E10
E15
E20
E30
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
6.8
10.1
13.6
19.5
28.8
10.6
15.9
21.2
30.4
1
1
1
2
2
2
1
1
1
2
2
2
1
1
2
2
2
1
1
2
2
11.1
15.5
22.2
33.0
44.1
61.6
13.3
18.8
26.6
39.9
53.2
74.3
8.5
12.7
17.1
24.5
36.1
10.6
16.0
21.3
30.5
32.1
32.1
32.1
38.0
51.5
65.4
87.3
32.1
32.1
32.8
42.1
58.1
74.0
99.3
17.4
17.4
20.3
25.6
34.4
48.4
13.9
17.2
23.6
30.0
41.1
Max
Fuse2/
Breaker3
Size
(Amps)
35
35
35
40
60
70
90
35
35
35
45
60
80
100
20
20
25
30
35
50
15
20
25
30
45
1. Minimum Circuit Ampacity.
2. Dual Element, Time Delay Type.
3. HACR type per NEC.
26
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 13:ELECTRICAL DATA - DJ036, 048 & 060 DIRECT DRIVE W/POWERED CONVENIENCE OUTLET
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 11.3
68.0
17.5
2.3
6.0
10.0
230-1-60 11.3
68.0
17.5
2.3
6.0
10.0
208-3-60 8.3
68.0
13.0
2.3
6.0
10.0
230-3-60 8.3
68.0
13.0
2.3
6.0
10.0
208-1-60 15.4
86.0
24.0
2.3
7.6
10.0
230-1-60 15.4
86.0
24.0
2.3
7.6
10.0
208-3-60 11.5
84.0
18.0
2.3
7.6
10.0
230-3-60 11.5
84.0
18.0
2.3
7.6
10.0
036
(3.0)
048
(4.0)
Johnson Controls Unitary Products
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
32.4
44.0
53.7
68.1
91.5
115.6
32.4
47.6
59.1
75.2
102.8
130.4
29.1
33.9
39.4
47.8
61.3
75.2
29.1
35.9
42.6
51.9
67.8
83.7
39.1
46.0
55.7
70.1
93.5
117.6
39.1
49.6
61.1
77.2
104.8
132.4
34.3
35.9
41.4
49.8
63.3
77.2
34.3
37.9
44.6
53.9
69.8
85.7
Max
Fuse2/
Breaker3
Size
(Amps)
40
45
60
70
100
125
40
50
60
80
110
150
35
35
40
50
70
80
35
40
45
60
70
90
50
50
60
80
100
125
50
50
70
80
110
150
45
45
45
50
70
80
45
45
45
60
70
90
27
362246-YIM-C-0109
TABLE 13:ELECTRICAL DATA - DJ036, 048 & 060 DIRECT DRIVE W/POWERED CONVENIENCE OUTLET (CONT)
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 28.8 145.0 45.0
2.3
7.6
10.0
230-1-60 28.8 145.0 45.0
2.3
7.6
10.0
208-3-60 17.3 123.0 27.0
2.3
7.6
10.0
230-3-60 17.3 123.0 27.0
2.3
7.6
10.0
060
(5.0)
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
19.2
26.9
38.5
57.2
76.4
106.7
23.0
32.6
46.1
69.1
92.2
128.7
11.1
15.5
22.2
33.0
44.1
61.6
13.3
18.8
26.6
39.9
53.2
74.3
55.9
55.9
55.9
70.1
93.5
117.6
155.4
55.9
55.9
61.1
77.2
104.8
132.4
176.2
41.5
41.5
41.5
49.8
63.3
77.2
99.0
41.5
41.5
44.6
53.9
69.8
85.7
111.0
Max
Fuse2/
Breaker3
Size
(Amps)
60
60
60
80
100
125
175
60
60
70
80
110
150
200
45
45
45
50
70
80
100
45
45
45
60
70
90
125
1. Minimum Circuit Ampacity.
2. Dual Element, Time Delay Type.
3. HACR type per NEC.
28
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 14:ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE WITH POWERED CONVENIENCE OUTLET
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 11.3
68.0
17.5
2.3
7.6
10.0
230-1-60 11.3
68.0
17.5
2.3
7.6
10.0
208-3-60 8.3
68.0
13.0
2.3
5.2
10.0
230-3-60 8.3
68.0
13.0
2.3
5.2
10.0
460-3-60 5.1
34.0
8.0
1.3
2.6
5.0
575-3-60 3.2
26.0
5.0
1.3
2.0
4.0
208-1-60 15.4
86.0
24.0
2.3
7.6
10.0
230-1-60 15.4
86.0
24.0
2.3
7.6
10.0
208-3-60 11.5
84.0
18.0
2.3
5.2
10.0
230-3-60 11.5
84.0
18.0
2.3
5.2
10.0
460-3-60 5.8
42.0
9.0
1.3
2.6
5.0
575-3-60 5.1
34.0
8.0
1.3
2.0
4.0
036
(3.0)
048
(4.0)
Johnson Controls Unitary Products
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E07
E10
E15
E20
None
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E07
E10
E15
E20
None
E10
E15
E20
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
6.8
10.1
13.6
19.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
6.8
10.1
13.6
19.5
10.6
15.9
21.2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
2
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
8.5
12.7
17.1
24.5
10.6
16.0
21.3
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
8.5
12.7
17.1
24.5
10.6
16.0
21.3
34.0
46.0
55.7
70.1
93.5
117.6
34.0
49.6
61.1
77.2
104.8
132.4
28.3
32.9
38.4
46.8
60.3
74.2
28.3
34.9
41.6
50.9
66.8
82.7
15.3
19.7
24.7
29.9
38.8
11.2
20.2
26.6
33.0
39.1
46.0
55.7
70.1
93.5
117.6
39.1
49.6
61.1
77.2
104.8
132.4
31.9
32.9
38.4
46.8
60.3
74.2
31.9
34.9
41.6
50.9
66.8
82.7
16.1
19.7
24.7
29.9
38.8
13.4
20.2
26.6
33.0
Max
Fuse2/
Breaker3
Size
(Amps)
45
50
60
80
100
125
45
50
70
80
110
150
35
35
40
50
70
80
35
40
45
60
70
90
20
20
25
30
40
15
25
30
35
50
50
60
80
100
125
50
50
70
80
110
150
40
40
40
50
70
80
40
40
45
60
70
90
20
20
25
30
40
15
25
30
35
29
362246-YIM-C-0109
TABLE 14:ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE WITH POWERED CONVENIENCE OUTLET (CONT)
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 28.8 145.0 45.0
2.3
7.6
10.0
230-1-60 28.8 145.0 45.0
2.3
7.6
10.0
208-3-60 17.3 123.0 27.0
2.3
5.2
10.0
230-3-60 17.3 123.0 27.0
2.3
5.2
10.0
460-3-60 9.6
70.0
15.0
1.3
2.6
5.0
575-3-60 7.4
53.0
11.5
1.3
2.0
4.0
060
(5.0)
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E07
E10
E15
E20
E30
None
E10
E15
E20
E30
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
6.8
10.1
13.6
19.5
28.8
10.6
15.9
21.2
30.4
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
1
1
2
2
2
1
1
2
2
19.2
26.9
38.5
57.2
76.4
106.7
23.0
32.6
46.1
69.1
92.2
128.7
11.1
15.5
22.2
33.0
44.1
61.6
13.3
18.8
26.6
39.9
53.2
74.3
8.5
12.7
17.1
24.5
36.1
10.6
16.0
21.3
30.5
55.9
55.9
55.9
70.1
93.5
117.6
155.4
55.9
55.9
61.1
77.2
104.8
132.4
176.2
39.1
39.1
39.1
46.8
60.3
74.2
96.0
39.1
39.1
41.6
50.9
66.8
82.7
108.0
20.9
20.9
24.7
29.9
38.8
52.8
16.3
20.2
26.6
33.0
44.1
Max
Fuse2/
Breaker3
Size
(Amps)
60
60
60
80
100
125
175
60
60
70
80
110
150
200
40
40
40
50
70
80
100
40
40
45
60
70
90
110
25
25
25
30
40
60
20
25
30
35
45
1. Minimum Circuit Ampacity.
2. Dual Element, Time Delay Type.
3. HACR type per NEC.
30
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 15:ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE HIGH STATIC WITH POWERED CONVENIENCE
OUTLET
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-1-60 11.3
68.0
17.5
2.3
7.6
10.0
230-1-60 11.3
68.0
17.5
2.3
7.6
10.0
208-3-60 8.3
68.0
13.0
2.3
5.2
10.0
230-3-60 8.3
68.0
13.0
2.3
5.2
10.0
460-3-60 5.1
34.0
8.0
1.3
2.6
5.0
575-3-60 3.2
26.0
5.0
1.3
2.0
4.0
208-1-60 15.4
86.0
24.0
2.3
7.6
10.0
230-1-60 15.4
86.0
24.0
2.3
7.6
10.0
208-3-60 11.5
84.0
18.0
2.3
5.2
10.0
230-3-60 11.5
84.0
18.0
2.3
5.2
10.0
460-3-60 5.8
42.0
9.0
1.3
2.6
5.0
575-3-60 5.1
34.0
8.0
1.3
2.0
4.0
036
(3.0)
048
(4.0)
Johnson Controls Unitary Products
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E07
E10
E15
E20
None
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E05
E07
E10
E15
E20
None
E07
E10
E15
E20
None
E10
E15
E20
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
6.8
10.1
13.6
19.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
4.0
5.6
8.0
11.9
15.9
5.3
7.5
10.6
15.9
21.2
6.8
10.1
13.6
19.5
10.6
15.9
21.2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
2
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
8.5
12.7
17.1
24.5
10.6
16.0
21.3
19.2
26.9
38.5
57.2
76.4
23.0
32.6
46.1
69.1
92.2
11.1
15.5
22.2
33.0
44.1
13.3
18.8
26.6
39.9
53.2
8.5
12.7
17.1
24.5
10.6
16.0
21.3
34.0
46.0
55.7
70.1
93.5
117.6
34.0
49.6
61.1
77.2
104.8
132.4
28.3
32.9
38.4
46.8
60.3
74.2
28.3
34.9
41.6
50.9
66.8
82.7
15.3
19.7
24.7
29.9
38.8
11.2
20.2
26.6
33.0
39.1
46.0
55.7
70.1
93.5
117.6
39.1
49.6
61.1
77.2
104.8
132.4
31.9
32.9
38.4
46.8
60.3
74.2
31.9
34.9
41.6
50.9
66.8
82.7
16.1
19.7
24.7
29.9
38.8
13.4
20.2
26.6
33.0
Max
Fuse2/
Breaker3
Size
(Amps)
45
50
60
80
100
125
45
50
70
80
110
150
35
35
40
50
70
80
35
40
45
60
70
90
20
20
25
30
40
15
25
30
35
50
50
60
80
100
125
50
50
70
80
110
150
40
40
40
50
70
80
40
40
45
60
70
90
20
20
25
30
40
15
25
30
35
31
362246-YIM-C-0109
TABLE 15:ELECTRICAL DATA - DJ036, 048 & 060 BELT DRIVE HIGH STATIC WITH POWERED CONVENIENCE
OUTLET (CONT)
Size
(Tons)
Volt
Compressors
(each)
RLA LRA
MCC
OD Fan
Motors
(each)
Supply
Blower
Motor
Pwr
Conv
Outlet
FLA
FLA
FLA
208-3-60 17.3 123.0 27.0
2.3
8.2
10.0
230-3-60 17.3 123.0 27.0
2.3
8.2
10.0
460-3-60 9.6
70.0
15.0
1.3
4.1
5.0
575-3-60 7.4
53.0
11.5
1.3
3.6
4.0
060
(5.0)
Electric Heat Option
MCA1
(Amps)
Model
kW
Stages
Amps
None
E05
E07
E10
E15
E20
E30
None
E05
E07
E10
E15
E20
E30
None
E07
E10
E15
E20
E30
None
E10
E15
E20
E30
4.0
5.6
8.0
11.9
15.9
22.2
5.3
7.5
10.6
15.9
21.2
29.6
6.8
10.1
13.6
19.5
28.8
10.6
15.9
21.2
30.4
1
1
1
2
2
2
1
1
1
2
2
2
1
1
2
2
2
1
1
2
2
11.1
15.5
22.2
33.0
44.1
61.6
13.3
18.8
26.6
39.9
53.2
74.3
8.5
12.7
17.1
24.5
36.1
10.6
16.0
21.3
30.5
42.1
42.1
42.2
50.5
64.0
77.9
99.8
42.1
42.1
45.3
54.6
70.6
86.5
111.8
22.4
22.4
26.6
31.8
40.7
54.7
17.9
22.2
28.6
35.0
46.1
Max
Fuse2/
Breaker3
Size
(Amps)
45
45
45
60
70
80
100
45
45
50
60
80
90
125
25
25
30
35
45
60
20
25
30
35
50
1. Minimum Circuit Ampacity.
2. Dual Element, Time Delay Type.
3. HACR type per NEC.
32
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 16:ELECTRIC HEAT CORRECTION FACTORS
NOMINAL VOLTAGE
VOLTAGE
kW CAP. MULTIPLIER
208
208
1.00
240
230
0.92
480
460
0.92
600
575
0.92
TABLE 17:VOLTAGE LIMITATIONS1
VOLTAGE
POWER SUPPLY
MIN.
MAX.
208/230-1-60
187
252
208/230-3-60
187
252
460-3-60
432
504
575-3-60
540
630
1. Utilization Range “A” in accordance with ARI Standard
110.
FIGURE 10 - UNIT DIMENSIONS (3 - 5 TON COOLING ONLY/ELECTRIC HEAT) FRONT VIEW
Johnson Controls Unitary Products
33
362246-YIM-C-0109
FIGURE 11 - UNIT DIMENSIONS (3 - 5 TON COOLING/GAS HEAT) FRONT VIEW
DETAIL “A”
FIGURE 12 - UNIT WITH ECONOMIZER RAINHOOD
34
Johnson Controls Unitary Products
362246-YIM-C-0109
DETAIL “B”
FIGURE 13 - UNIT WITH FIXED OUTDOOR AIR/MOTORIZED DAMPER RAINHOOD
FIGURE 14 - UNIT DIMENSIONS (REAR VIEW)
Johnson Controls Unitary Products
35
362246-YIM-C-0109
Filter Access
Blower Motor Access
Dot Plugs
Field-Supplied Disconnect
Switch Location
Mounting Bracket for
Disconnect Switch
A,B
(Field Supplied)
Wiring Entry
(See Detail “B”)
Control Box Access
Disconnect Switch Location
and Motor Access Panel for
Unit with “Belt-Drive” Option
FIGURE 15 - DISCONNECT/BLOWER ACCESS LOCATION
TABLE 18:UTILITIES ENTRY
TABLE 19:MINIMUM CLEARANCES
HOLE
OPENING SIZE (DIA.)
USED FOR
A
7/8” KO1
Control Wiring2
B
2” KO1
Power Wiring
C
1-5/8” KO
Gas Piping (Front)
D
1-1/2” KO
Gas Piping (Bottom)
Side
Bottom
Side
Bottom
1. Opening in the bottom to the unit can be located by the
side in the insulation.
2. Do not remove the 2” knockout ring.
LOCATION
CLEARANCE
Front
24” (Cooling/Electric Heat)
32” (Gas Heat)
Rear
12” (Less Economizer)
36” (With Economizer or Fixed
Air/Motorized Damper)
Left Side (Filter Access)
24” (Less Economizer)
36” (With Economizer)
Right Side (Cond. Coil)
24”
Below Unit1
0”
Above Unit2
72” (For
Condenser Air Discharge)
1. Units may be installed on combustible floors made
from wood or class A, B, or C roof covering material.
2. Units must be installed outdoors. Overhanging structures or shrubs should not obstruct condenser air discharge outlet.
36
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 20:SUPPLY AIR BLOWER PERFORMANCE (DJ036 BELT DRIVE) - SIDE DUCT APPLICATION
Available External Static Pressure - IWG1
Air
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Flow
(CFM) RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
800
1000
1200
1400
1600
1.
2.
3.
4.
Field Supplied Drive
634
0.34
735
0.39
659
0.39
760
0.45
685
0.47
786
0.52
716
0.57
816
0.62
752
0.69
852
0.75
828
853
879
909
945
0.45
0.51
0.58
0.68
0.81
Standard Drive Option
914
0.52
995
0.59
939
0.57 1019 0.65
965
0.65 1045 0.72
995
0.75 1076 0.82
1032 0.88 1112 0.95
1070
1094
1120
1151
1187
0.67
0.72
0.80
0.90
1.03
1140
1165
1191
1221
1258
0.75
0.80
0.88
0.98
1.11
HIgh Static Drive Option
1207 0.83 1270 0.92
1232 0.89 1295 0.97
1258 0.96 1321 1.05
1288 1.06 1352 1.15
1324 1.19 1388 1.27
1332 1.00
1356 1.06
1382 1.13
1413 1.23
1449 1.36
FS4
Blower performance includes gas heat exchangers and 1” filters. See STATIC RESISTANCE table for additional applications.
See RPM SELECTION table to determine desired motor sheave setting and to determine the maximum continuous BHP.
kW = BHP x 0.932.
Field Supplied Drive.
TABLE 21:SUPPLY AIR BLOWER PERFORMANCE (DJ036 BELT DRIVE) - BOTTOM DUCT APPLICATION
Available External Static Pressure - IWG1
Air
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Flow
(CFM) RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
800
1000
1200
1400
1600
Field Supplied Drive
613
0.35
724
0.40
640
0.40
751
0.46
669
0.48
779
0.53
702
0.57
812
0.63
741
0.70
852
0.75
826
853
881
914
954
0.46
0.52
0.59
0.69
0.81
Standard Drive Option
920
0.53 1007 0.60
947
0.58 1034 0.65
975
0.65 1063 0.73
1009 0.75 1096 0.82
1048 0.88 1135 0.95
1089
1116
1144
1177
1217
0.67
0.73
0.80
0.90
1.02
1165
1192
1220
1254
1293
0.75
0.80
0.88
0.98
1.10
HIgh Static Drive Option
1237 0.83 1306 0.91 1372 1.00
1264 0.89 1333 0.97 1399 1.05
1293 0.96 1361 1.04 1427 1.13
1326 1.06 1394 1.14 1460 1.22
1365 1.18 1434 1.26 1500 1.35
Field Supplied Drive
1. Blower performance includes gas heat exchangers and 1” filters. See STATIC RESISTANCE table for additional applications.
2. See RPM SELECTION table to determine desired motor sheave setting and to determine the maximum continuous BHP.
3. kW = BHP x 0.932.
TABLE 22:SUPPLY AIR BLOWER PERFORMANCE (DJ048 BELT DRIVE) - SIDE DUCT APPLICATION
Available External Static Pressure - IWG1
Air
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Flow
(CFM) RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
1000
1200
1400
1600
1800
2000
1.
2.
3.
4.
703
733
770
811
857
907
Field Supplied Drive
0.39
786
0.47
866
0.44
817
0.52
896
0.52
853
0.60
933
0.64
895
0.71
974
0.80
940
0.87 1020
1.00
990
1.07 1070
0.54
0.60
0.67
0.79
0.95
1.15
942
973
1010
1051
1097
1146
0.62
0.68
0.76
0.87
1.03
1.23
1016
1047
1083
1125
1171
1220
Standard Drive Option
0.71 1087 0.79 1155
0.76 1118 0.85 1186
0.84 1154 0.93 1222
0.96 1196 1.04 1264
1.11 1242 1.20 1310
1.31 1291 1.40 1359
0.88
0.94
1.02
1.13
1.29
1.49
1221
1252
1288
1330
1375
1425
0.98
1.03
1.11
1.23
1.38
1.58
HIgh Static Drive Option
1284 1.07 1345 1.17
1315 1.12 1376 1.22
1352 1.20 1413 1.30
1393 1.32 1454 1.42
1439 1.48 1500 1.58
1488 1.68 1550 1.77
FS4
Blower performance includes gas heat exchangers and 1” filters. See STATIC RESISTANCE table for additional applications.
See RPM SELECTION table to determine desired motor sheave setting and to determine the maximum continuous BHP.
kW = BHP x 0.932.
Field Supplied Drive.
Johnson Controls Unitary Products
37
362246-YIM-C-0109
TABLE 23:SUPPLY AIR BLOWER PERFORMANCE (DJ048 BELT DRIVE) - BOTTOM DUCT APPLICATION
Available External Static Pressure - IWG1
Air
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Flow
(CFM) RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
1000
1200
1400
1600
1800
2000
688
722
761
807
856
910
Field Supplied Drive
0.40
779
0.47
866
0.45
812
0.53
899
0.53
852
0.60
939
0.65
897
0.72
984
0.80
947
0.87 1034
0.99 1001 1.06 1088
0.55
0.60
0.68
0.79
0.95
1.14
949
983
1022
1068
1118
1172
0.63
0.68
0.76
0.87
1.02
1.22
1029
1063
1103
1148
1198
1252
Standard Drive Option
0.71 1107 0.80 1181
0.76 1140 0.85 1215
0.84 1180 0.92 1254
0.95 1225 1.04 1300
1.11 1275 1.19 1349
1.30 1329 1.39 1403
0.88
0.93
1.01
1.13
1.28
1.47
1253
1286
1326
1371
1421
1475
0.97
1.03
1.10
1.22
1.37
1.56
HIgh Static Drive Option
1322 1.07 1388 1.16
1355 1.12 1422 1.21
1395 1.20 1462 1.29
1440 1.31 1507 1.40
1490 1.46 1557 1.56
1544 1.66 1611 1.75
Field Supplied Drive
1. Blower performance includes gas heat exchangers and 1” filters. See STATIC RESISTANCE table for additional applications.
2. See RPM SELECTION table to determine desired motor sheave setting and to determine the maximum continuous BHP.
3. kW = BHP x 0.932.
TABLE 24:SUPPLY AIR BLOWER PERFORMANCE (DJ060 BELT DRIVE) - SIDE DUCT APPLICATION
Available External Static Pressure - IWG1
Air
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Flow
(CFM) RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
1200
1400
1600
1800
2000
2200
2400
2600
733
770
811
857
907
960
1015
1074
Field Supplied Drive
0.44
817
0.52
896
0.52
853
0.60
933
0.64
895
0.71
974
0.80
940
0.87 1020
1.00
990
1.07 1070
1.24 1043 1.31 1123
1.51 1099 1.59 1178
1.83 1157 1.90 1237
0.60
0.67
0.79
0.95
1.15
1.39
1.66
1.98
973
1010
1051
1097
1146
1199
1255
1314
0.68
0.76
0.87
1.03
1.23
1.47
1.74
2.06
Standard Drive Option
1047 0.76 1118 0.85
1083 0.84 1154 0.93
1125 0.96 1196 1.04
1171 1.11 1242 1.20
1220 1.31 1291 1.40
1273 1.55 1344 1.64
1329 1.83 1400 1.92
1387 2.14 1458 2.23
1186
1222
1264
1310
1359
1412
1468
-
0.94
1.02
1.13
1.29
1.49
1.73
2.01
-
1252
1288
1330
1375
1425
1478
1534
-
HIgh Static Drive Option
1.03 1315 1.12 1376
1.11 1352 1.20 1413
1.23 1393 1.32 1454
1.38 1439 1.48 1500
1.58 1488 1.68 1550
1.82 1541 1.92 1602
2.10 1597 2.19 1658
-
1.22
1.30
1.42
1.58
1.77
2.01
2.29
-
1. Blower performance includes gas heat exchangers and 1” filters. See STATIC RESISTANCE table for additional applications.
2. See RPM SELECTION table to determine desired motor sheave setting and to determine the maximum continuous BHP.
3. kW = BHP x 0.932.
TABLE 25:SUPPLY AIR BLOWER PERFORMANCE (DJ060 BELT DRIVE) - BOTTOM DUCT APPLICATION
Available External Static Pressure - IWG1
Air
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Flow
(CFM) RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
1200
1400
1600
1800
2000
2200
2400
2600
722
761
807
856
910
968
1029
1093
Field Supplied Drive
0.45
812
0.53
899
0.53
852
0.60
939
0.65
897
0.72
984
0.80
947
0.87 1034
0.99 1001 1.06 1088
1.23 1059 1.30 1146
1.50 1119 1.57 1206
1.81 1183 1.88 1270
0.60
0.68
0.79
0.95
1.14
1.37
1.65
1.95
983
1022
1068
1118
1172
1229
1290
1354
0.68
0.76
0.87
1.02
1.22
1.45
1.72
2.03
Standard Drive Option
1063 0.76 1140 0.85
1103 0.84 1180 0.92
1148 0.95 1225 1.04
1198 1.11 1275 1.19
1252 1.30 1329 1.39
1309 1.53 1387 1.62
1370 1.81 1448 1.89
1434 2.11 1511 2.20
1215
1254
1300
1349
1403
1461
1522
1586
0.93
1.01
1.13
1.28
1.47
1.71
1.98
2.29
1286
1326
1371
1421
1475
1533
1593
-
HIgh Static Drive Option
1.03 1355 1.12 1422 1.21
1.10 1395 1.20 1462 1.29
1.22 1440 1.31 1507 1.40
1.37 1490 1.46 1557 1.56
1.56 1544 1.66 1611 1.75
1.80 1602 1.89 1668 1.99
2.07 1663 2.16 1729 2.26
Field Supplied Drive
1. Blower performance includes gas heat exchangers and 1” filters. See STATIC RESISTANCE table for additional applications.
2. See RPM SELECTION table to determine desired motor sheave setting and to determine the maximum continuous BHP.
3. kW = BHP x 0.932.
38
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 26:SUPPLY AIR BLOWER PERFORMANCE (DJ036, 048, & 060 DIRECT DRIVE) SIDE DUCT APPLICATION
CFM
WATTS
CFM
WATTS
CFM
WATTS
CFM
WATTS
CFM
WATTS
CFM
WATTS
CFM
WATTS
1.0
WATTS
53
0.9
CFM
43
0.3
WATTS
33
HI
MED/HI
MED
MED/LOW
LOW
HI
MED/HI
MED
MED/LOW
LOW
HI
MED/HI
MED
MED/LOW
LOW
0.2
CFM
UNIT
MOTOR1
TONNAGE SPEED
AVAILABLE EXTERNAL STATIC PRESSURE - IWG2
0.4
0.5
0.6
0.7
0.8
1582
1488
1339
1233
1081
2056
1866
1680
1582
1300
2256
2145
2020
1757
1570
320
263
208
171
130
636
539
408
362
223
883
771
637
413
327
1538
1440
1292
1184
997
2017
1832
1641
1541
1258
2258
2127
1999
1713
1536
335
276
221
183
134
696
557
426
380
237
931
784
656
432
339
1496
1396
1247
1135
935
1978
1795
1594
1495
1202
2247
2119
1985
1677
1499
349
290
234
195
145
714
571
438
391
247
950
808
675
451
356
1458
1354
1201
1082
863
1942
1754
1558
1465
2223
2089
1947
1639
-
363
303
246
207
158
734
585
455
406
964
826
696
468
-
1418
1309
1152
1026
1906
1722
1517
1426
2182
2051
1910
1597
-
376
316
258
220
749
602
472
423
979
844
715
479
-
1381
1263
1102
957
1864
1679
1469
1377
2125
2014
1876
1559
-
390
329
272
235
764
619
490
440
971
859
730
497
-
1338
1214
1036
895
1815
1636
1415
1326
2044
1965
1832
1521
-
403
343
288
248
769
638
505
455
940
861
740
513
-
1298
1158
967
1728
1582
1370
1292
1958
1896
1793
1472
-
417
358
303
743
653
521
469
898
843
756
523
-
1255
1085
924
1582
1508
1337
1247
1864
1801
1725
-
430
374
313
685
639
536
485
854
806
748
-
1. Factory set on medium speed tap.
2. Includes allowances for a wet evaporator coil, 1” filters, and the heat exchangers. Refer to STATIC RESISTANCES Table for resistance values.
3. Side Duct application (230 Volts)
TABLE 27:SUPPLY AIR BLOWER PERFORMANCE (DJ036, 048, & 060 DIRECT DRIVE) BOTTOM DUCT APPLICATION
WATTS
CFM
WATTS
CFM
WATTS
CFM
WATTS
CFM
WATTS
CFM
WATTS
CFM
WATTS
1.0
CFM
0.9
WATTS
53
AVAILABLE EXTERNAL STATIC PRESSURE - IWG2
0.5
0.6
0.7
0.8
CFM
43
0.4
WATTS
33
HI
MED/HI
MED
MED/LOW
LOW
HI
MED/HI
MED
MED/LOW
LOW
HI
MED/HI
MED
MED/LOW
LOW
0.3
CFM
UNIT
MOTOR1
TONNAGE SPEED
0.2
1527
1437
1293
1191
1045
1985
1802
1622
1528
1256
2177
2071
1950
1697
1516
320
263
208
171
130
636
539
408
362
223
883
771
637
413
327
1485
1391
1248
1144
964
1947
1768
1585
1489
1216
2179
2053
1929
1654
1484
335
276
221
183
134
696
557
426
380
237
931
784
656
432
339
1445
1349
1205
1097
904
1909
1733
1539
1444
1161
2169
2045
1916
1619
1448
349
290
234
195
145
714
571
438
391
247
950
808
675
451
356
1408
1308
1161
1046
1875
1694
1505
1415
2145
2016
1880
1583
-
363
303
246
207
734
585
455
406
964
826
696
468
-
1370
1265
1114
992
1840
1662
1465
1377
2106
1980
1844
1542
-
376
316
258
220
749
602
472
423
979
844
715
479
-
1334
1221
1065
926
1800
1621
1419
1330
2051
1944
1811
1506
-
390
329
272
235
764
619
490
440
971
859
730
497
-
1292
1174
1002
866
1752
1580
1367
1281
1973
1897
1768
1469
-
403
343
288
248
769
638
505
455
940
861
740
513
-
1254
1120
935
1668
1528
1324
1248
1890
1830
1731
-
417
358
303
743
653
521
469
898
843
756
-
1213
1049
894
1528
1456
1291
1205
1800
1739
1665
-
430
374
313
685
639
536
485
854
806
748
-
1. Factory set on medium speed tap.
2. Includes allowances for a wet evaporator coil, 1” filters, and the heat exchangers. Refer to STATIC RESISTANCES Table for resistance values.
3. Bottom Duct application (230 Volts)
TABLE 28:BELT DRIVE RPM SELECTION
Size
(Tons)
036
(3)
048
(4)
060
(5)
HP
1.5
1.5
1.5
1.5
1.5
2
Max
BHP
1.73
1.73
1.73
1.73
1.73
2.3
Motor
Sheave
1VL44
1VP56
1VL44
1VP56
1VL44
1VP56
Johnson Controls Unitary Products
Blower
Sheave
AK64
AK66
AK56
AK61
AK56
AK56
5 Turns
Open
805
1115
930
1210
930
1325
4 Turns
Open
865
1170
995
1270
995
1395
3 Turns
Open
920
1225
1060
1330
1060
1460
2 Turns
Open
980
1280
1130
1390
1130
1525
1 Turn
Open
1035
1335
1195
1455
1195
1590
Fully
Closed
1095
1390
1260
1515
1260
1660
39
362246-YIM-C-0109
TABLE 29:BELT DRIVE BLOWER MOTOR AND DRIVE DATA
Motor
Size
(Tons)
DJ036
DJ048
DJ060
HP
RPM
Eff.
SF
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
2
1725
1725
1725
1725
1725
1725
0.8
0.8
0.8
0.8
0.8
0.8
1.15
1.15
1.15
1.15
1.15
1.15
Motor Sheave
Blower Sheave
Datum Dia.
Datum Dia.
Bore (in.) Model
Bore (in.) Model
Frame
(in.)
(in.)
56
2.8 - 3.8
7/8
1VL44
6.0
1
AK64
56
4.0 - 5.0
7/8
1VP56
6.2
1
AK66
56
2.8 - 3.8
7/8
1VL44
5.2
1
AK56
56
4.0 - 5.0
7/8
1VP56
5.7
1
AK61
56
2.8 - 3.8
7/8
1VL44
5.2
1
AK56
56
4.0 - 5.0
7/8
1VP56
5.2
1
AK56
Belt
A37
A39
A36
A38
A36
A38
TABLE 30:STATIC RESISTANCES
RESISTANCE, IWG
CFM
1800
2000
2200
0.13
0.15
0.17
0.08
0.10
0.12
0.11
0.13
0.15
0.16
0.18
0.20
DESCRIPTION
ECONOMIZER1,3
ELECTRIC
HEATERS1
7-15KW
20-30KW
COOLING ONLY2
1000
0.07
0.04
0.06
0.08
1200
0.08
0.05
0.07
0.10
1400
0.09
0.06
0.08
0.12
1600
0.11
0.07
0.09
0.14
2400
0.20
0.14
0.17
0.23
2600
0.23
0.16
0.20
0.26
2800
0.26
0.19
0.23
0.29
3000
0.30
0.22
0.26
0.32
1. Deduct these resistance values from the available external static pressure shown in SUPPLY AIR BLOWER PERFORMANCE Tables.
2. Add these resistance values to the available static resistance values on SUPPLY AIR BLOWER PERFORMANCE Tables.
3. The pressure through the economizer is greater for 100% outdoor air than for 100% return air. If the resistance of the return air duct system is less than
0.25 IWG, the unit will deliver less CFM during full economizer operation.
Drive Selection
1.
Determine side or bottom supply air duct application.
2.
Determine desired airflow.
3.
Calculate or measure the amount of external static pressure.
4.
Using the operating point determined from steps 1, 2 & 3, locate this point on the appropriate supply air blower performance table. (Linear
interpolation may be necessary.)
5.
Noting the RPM and BHP from step 4, locate the appropriate motor and/or drive on the RPM selection table.
6.
Review the BHP compared to the motor options available. Select the appropriate motor and/or drive.
7.
Review the RPM range for the motor options available. Select the appropriate drive if multiple drives are available for the chosen motor.
8.
Determine turns open to obtain the desired operation point.
Example
1.
2200 CFM
2.
1.6 iwg
3.
Using the supply air blower performance table below, the following data point was located: 1478 RPM & 1.82 BHP.
4.
Using the RPM selection table below, Size X and Model Y is found.
5.
1.82 BHP exceeds the maximum continuous BHP rating of the 1.5 HP motor. The 2 HP motor is required.
6.
1478 RPM is within the range of the 2 HP drive.
7.
Using the 2 HP motor and drive, 2.5 turns open will achieve 1478 RPM.
Example Supply Air Blower Performance
Air Flow
(CFM)
2000
2200
2400
2600
Available External Static Pressure - IWG
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
Field Supplied
Drive
907
1.00
990
960
1.24 1043
1015 1.51 1099
1074 1.83 1157
Standard Drive Option
1.07
1.31
1.59
1.90
1070
1123
1178
1237
1.15
1.39
1.66
1.98
1146
1199
1255
1314
HIgh Static Drive Option
1.23
1.47
1.74
2.06
1220
1273
1329
1387
1.31
1.55
1.83
2.14
1291
1344
1400
1458
1.40
1.64
1.92
2.23
1359
1412
1468
-
1.49
1.73
2.01
-
1425
1478
1534
-
1.58
1.82
2.10
-
1488
1541
1597
-
1.68
1.92
2.19
-
1550
1602
1658
-
1.77
2.01
2.29
-
Table X: RPM Selection
Size
(Tons)
Model
HP
Max
BHP
Motor
Sheave
Blower
Sheave
5 Turns
Open
4 Turns
Open
3 Turns
Open
2 Turns
Open
1 Turn
Open
Fully
Closed
X
Y
1.5
2
1.73
2.3
1VL44
1VP56
AK56
AK56
930
1325
995
1395
1060
1460
1130
1525
1195
1590
1260
1660
40
Johnson Controls Unitary Products
362246-YIM-C-0109
Altitude/Temperature Correction Factors
Air
Temp.
40
50
60
70
80
90
100
0
1.060
1.039
1.019
1.000
0.982
0.964
0.946
1000
1.022
1.002
0.982
0.964
0.947
0.929
0.912
2000
0.986
0.966
0.948
0.930
0.913
0.897
0.880
3000
0.950
0.931
0.913
0.896
0.880
0.864
0.848
4000
0.916
0.898
0.880
0.864
0.848
0.833
0.817
Altitude (Ft.)
5000
0.882
0.864
0.848
0.832
0.817
0.802
0.787
6000
0.849
0.832
0.816
0.801
0.787
0.772
0.758
7000
0.818
0.802
0.787
0.772
0.758
0.744
0.730
8000
0.788
0.772
0.757
0.743
0.730
0.716
0.703
9000
0.758
0.743
0.729
0.715
0.702
0.689
0.676
10000
0.729
0.715
0.701
0.688
0.676
0.663
0.651
1.100
1.050
Correction Factor
1.000
Sea Level
0.950
1000 ft
0.900
2000 ft
0.850
3000 ft
0.800
5000 ft
0.750
6000 ft
7000 ft
4000 ft
8000 ft
0.700
9000 ft
10000 ft
0.650
0.600
40
50
60
70
80
90
100
Air Temperature (ºF)
Johnson Controls Unitary Products
41
362246-YIM-C-0109
PHASING
Check for proper compressor rotation. If the blower or
compressors rotate in the wrong direction at start-up,
the electrical connection to the unit is misphased.
Change the incoming line connection phasing to obtain
proper rotation. (Scroll compressors operate in only
one direction. If the scroll is drawing low amperage,
has similar suction and discharge pressures, or producing a high noise level, the scroll is misphased).
Scroll compressors require proper rotation to
operate correctly. Do not change the internal
wiring to make the blower, condenser fans, or
compressor rotate correctly. Change the
incoming power to the main terminal block to
obtain proper rotation.
SUPPLY AIR BLOWERS
These blowers have either multi-speed direct drive
motors or single speed motors equipped with a belt
drive. Belt drive units have a variable pitch pulley that
allows the blower speed to be adjusted.
CHECKING SUPPLY AIR CFM
The RPM of the supply air blower will depend on the
required CFM, the unit accessories or options and the
static resistances of both the supply and the return air
duct systems. With this information, the motor speed
tap (direct drive) or the motor pulley number of turns
open (belt drive) can be determined from the Blower
Performance Data Tables.
PROCEDURE FOR ADJUSTING BELT TENSION:
1. Loosen nuts (A) (top and bottom).
2. Adjust the tension by turning bolt (B).
3. Never loosen nuts (C) from each other.
4. Use a belt tension checker to apply a perpendicular force to be one belt at the
midpoint of the span as shown. The deflection force should be applied
until a specific deflection distance of 4mm (5/32") is obtained. To determine
the deflection distance from normal position, use a straight edge from
sheave to sheave as a reference line. The recommended deflection force
is as follows:
SPAN LENGTH
DEFL FORCE
(B)
*Never Loosen
(A)
(C)*
Tension new belts at the max. deflection force recommended for the belt
section. Check the belt tension at least two times during the first 24 hours of
operation. Any re-tensioning should fall between the min. and max.
deflection force values.
5. After adjusting, re-tighten nuts (A).
FIGURE 16 - BELT ADJUSTMENT
Note the following:
1. The supply air CFM must be within the limitations
shown in the Unit Application Data Table 1.
2. Pulleys can be adjusted in half turn increments.
3. The tension on the belt should be adjusted as
shown in the Belt Adjustment Figure 16.
4. Tighten blower pulley and motor sheave set screws
after any adjustments. Re-check set screws after
10-12 hrs. run time is recommended.
Belt drive blower systems MUST be adjusted
to the specific static and CFM requirements for
the application. The belt drive blowers are NOT
set at the factory for any specific static or CFM.
Adjustments of the blower speed and belt tension are REQUIRED. Tighten blower pulley
and motor sheave set screws after these
adjustments. Re-checking set screws after 1012 hrs. run time is recommended.
42
Johnson Controls Unitary Products
362246-YIM-C-0109
To check the supply air CFM after the initial balancing
has been completed:
1. Remove the two 5/16” dot plugs from the blower
motor and the filter access panels shown in
Figure 15.
2. Insert at least 8" of 1/4 inch tubing into each of
these holes for sufficient penetration into the air
flow on both sides of the indoor coil.
NOTE: The tubes must be inserted and held in a posi-
tion perpendicular to the air flow so that velocity pressure will not affect the static pressure
readings.
0.9
048
060
0.8
PRESSURE DROP (IWG)
Start the supply air blower motor. Adjust the resistances in both the supply and the return air duct systems to balance the air distribution throughout the
conditioned space. The job specifications may require
that this balancing be done by someone other than the
equipment installer.
0.7
0.6
036
0.5
0.4
0.3
0.2
0.1
0
0
500
1000 1500 2000 2500 3000 3500
NOMINAL CFM
FIGURE 17 - PRESSURE DROP ACROSS COIL
OPERATION
SEQUENCE OF OPERATIONS OVERVIEW
3. Using an inclined manometer, determine the pressure drop across a dry evaporator coil. Since the
moisture on an evaporator coil may vary greatly,
measuring the pressure drop across a wet coil
under field conditions would be inaccurate. To
assure a dry coil, the compressors should be deactivated while the test is being run.
4. Knowing the pressure drop across a dry coil, the
actual CFM through the unit can be determined
from the curve in Pressure Drop vs. Supply Air
CFM (Figure 17).
For these units, the thermostat makes a circuit
between “R” and “Y1” for the cooling cycle.
The call is passed to the unit control board (UCB),
which then determines whether the requested operation is available and, if so, which components to energize.
For gas heating, the UCB monitors the “W1” call but
does not handle the operation of the gas furnace. An
ignition control board controls the gas heater operation.
For electric heat units, the UCB passes the call to the
electric heater.
Failure to properly adjust the total system air
quantity and static pressure can result in
extensive system damage.
After readings have been obtained, remove the tubes
and reinstall the two 5/16” dot plugs that were removed
in Step 1.
In both cases, when the “W1” call is sensed, the indoor
air blower is energized following a specified heating
delay.
If at any time a call for both heating and cooling are
present, the heating operation will be performed. If operating, the cooling system is halted as with a completion
of a call for cooling. Heating always takes priority.
NOTE: De-energize the compressors before taking any
test measurements to assure a dry indoor coil.
Johnson Controls Unitary Products
43
362246-YIM-C-0109
COOLING SEQUENCE OF OPERATION
CONTINUOUS BLOWER
By setting the room thermostat fan switch to “ON,” the
supply air blower will operate continuously.
INTERMITTENT BLOWER
With the room thermostat fan switch set to “AUTO” and
the system switch set to either the “AUTO” or “HEAT”
settings, the blower is energized whenever a cooling or
heating operation is requested. The blower is energized
after any specified delay associated with the operation.
When energized, the indoor blower has a minimum run
time of 30 seconds. Additionally, the indoor blower has
a delay of 10 seconds between operations.
NO OUTDOOR AIR OPTIONS
When the thermostat calls for cooling, the low-voltage
control circuit from “R” to “Y1” and “G” is completed.
The compressor and condenser fan motor are energized. After completing the specified fan on delay for
cooling, the UCB will energize the blower motor.
Once the thermostat has been satisfied, it will de-energize Y1. If the compressor has satisfied its minimum
run time, the compressor and condenser fan de-energize. Otherwise, the unit operates the cooling system
until the minimum run time for the compressor has
been completed. After the compressor de-energizes,
the blower is stopped following the elapse of the fan off
delay for cooling.
To be available, a compressor must not be locked-out
due to a high or low-pressure switch or freezestat trip and
the anti-short cycle delay (ASCD) must have elapsed.
ECONOMIZER WITH SINGLE ENTHALPY SENSOR
When the room thermostat calls for cooling, the low
voltage control circuit from “R” to “G” and “Y1” is completed. The UCB energizes the blower motor (if the fan
switch on the room thermostat is set in the “AUTO”
position) and drives the economizer dampers from fully
closed to their minimum position. If the enthalpy of the
outdoor air is below the setpoint of the enthalpy controller (previously determined), “Y1” energizes the
economizer. The dampers will modulate to maintain a
constant supply air temperature as monitored by the
discharge air sensor. If the outdoor air enthalpy is
above the setpoint, “Y1” energizes the compressor and
condenser fan motor only.
Once the thermostat has been satisfied, it will de-energize “Y1”. If the compressor has satisfied its minimum
run time, the compressor and condenser fan are deenergized. Otherwise, the unit operates the cooling sys-
44
tem until the minimum run times for the compressor has
been completed. After the compressor de-energizes, the
blower is stopped following the elapse of the fan off
delay for cooling, and the economizer damper goes to
the closed position. If the unit is in continues fan operation the economizer damper goes to the min. position.
ECONOMIZER WITH DUAL ENTHALPY SENSORS
The operation with the dual enthalpy sensors is identical to the single sensor except that a second enthalpy
sensor is mounted in the return air. This return air sensor allows the economizer to choose between outdoor
air and return air, whichever has the lowest enthalpy
value, to provide maximum operating efficiency.
ECONOMIZER (SINGLE OR DUAL) WITH POWER
EXHAUST
This system operates as specified above with one
addition. The power exhaust motor is energized 45
seconds after the actuator position exceeds the
exhaust fan setpoint on the economizer control. When
the power exhaust is operating, the second stage of
mechanical cooling will not operate. As always, the “R”
to “G” connection provides minimum position but does
not provide power exhaust operation.
MOTORIZED OUTDOOR AIR DAMPERS
This system operation is the same as the units with no
outdoor air options with one exception. When the “R” to
“G” circuit is complete, the motorized damper drives
open to a position set by the thumbnail on the damper
motor. When the “R” to “G” circuit is opened, the
damper spring returns fully closed.
COOLING OPERATION ERRORS
Each cooling system is monitored for operation outside
of the intended parameters. Errors are handled as
described below. All system errors override minimum
run times for compressors.
HIGH-PRESSURE LIMIT SWITCH
During cooling operation, if a high-pressure limit switch
opens, the UCB will de-energize the compressor, initiate the ASCD (Anti-short cycle delay), and, stop the
condenser fan. If the call for cooling is still present at
the conclusion of the ASCD, the UCB will re-energize
the compressor.
Should a high-pressure switch open three times within
two hours of operation, the UCB will lock-out the compressor and flash a code (see Table 39).
LOW-PRESSURE LIMIT SWITCH
The low-pressure limit switch is not monitored during
the initial 30 seconds of a cooling system's operation.
Johnson Controls Unitary Products
362246-YIM-C-0109
For the following 30 seconds, the UCB will monitor the
low-pressure switch to ensure it closes. If the low-pressure switch fails to close after the 30-second monitoring phase, the UCB will de-energize the compressor,
initiate the ASCD, and stop the condenser fan.
Once the low-pressure switch has been proven (closed
during the 30-second monitor period described above),
the UCB will monitor the low-pressure limit switch for any
openings. If the low-pressure switch opens for greater
than 5 seconds, the UCB will de-energize the compressor, initiate the ASCD, and stop the condenser fan.
If the call for cooling is still present at the conclusion of
the ASCD, the UCB will re-energize the compressor.
Should a low-pressure switch open three times within
one hour of operation, the UCB will lock-out the compressor and flash a code (Table 39).
FREEZESTAT
During cooling operation, if a freezestat opens, the
UCB will de-energize the compressor, initiate the
ASCD, and stop the condenser fan. If the call for cooling is still present at the conclusion of the ASCD, the
UCB will re-energize the compressor.
Should a freezestat open three times within two hours
of operation, the UCB will lock-out the compressor and
flash a code (Table 39).
LOW AMBIENT COOLING
To determine when to operate in low ambient mode,
the UCB has a pair of terminals connected to a temperature-activated switch set at 45ºF. When the low ambient switch is closed and the thermostat is calling for
cooling, the UCB will operate in the low ambient mode.
Low ambient mode operates the compressors in this
manner: 10 minutes on, 5 minutes off. The indoor
blower is operated throughout the cycle. The 5-minute
off period is necessary to defrost the indoor coil.
Low ambient mode always begins with compressor
operation. Compressor minimum run time may extend
the minutes of compressor operation. The defrost cycle
will begin immediately following the elapse of the minimum run time.
When operating in low ambient mode, the UCB will not
lockout the compressor due to a freezestat trip. However, a freezestat trip will de-energize the compressor.
If the call for cooling is still present at the end of the
ASCD and the freezestat has closed, the unit will
resume operation.
Johnson Controls Unitary Products
SAFETY CONTROLS
The unit control board monitors the following inputs for
the cooling system:
1. A suction line freezestat to protect against low
evaporator temperatures due to a low airflow or a
low return air temperature, (opens at 26 ± 5 °F and
resets at 38 ± 5°F).
2. A high-pressure switch to protect against excessive discharge pressures due to a blocked condenser coil or a condenser motor failure, (opens at
380 ± 10 psig and resets at 300 ± 10 psig).
3. A low-pressure switch to protect against loss of
refrigerant charge, (opens at 22 ± 5 psig and resets
at 45 ± 5 psig).
The above pressure switches are hard-soldered to the
unit. The refrigeration system is monitored and controlled. On any fault, the system will be affected by any
safety/preventive action.
The unit control board monitors the temperature limit
switch of electric heat units and the temperature limit
switch and the gas valve of gas furnace units.
COMPRESSOR PROTECTION
The compressor also has inherent (internal) protection.
If there is an abnormal temperature rise in a compressor, the protector will open to shut down the compressor. The UCB incorporates features to minimize
compressor wear and damage. An anti-short cycle
delay (ASCD) is utilized to prevent operation of a compressor too soon after its previous run. Additionally, a
minimum run time is imposed any time a compressor is
energized.
The ASCD is initiated on unit start-up and on any compressor reset or lock-out.
FLASH CODES
The UCB will initiate a flash code associated with
errors within the system. Refer to UNIT CONTROL
BOARD FLASH CODES Table 39.
RESET
Remove the call for cooling, by raising thermostat setting higher than the conditioned space temperature.
This resets any pressure or freezestat flash codes.
45
362246-YIM-C-0109
ELECTRIC HEATING SEQUENCE OF OPERATIONS
The following sequence describes the operation of the
electric heat section.
Single-stage heating (applies only to 5, 7 & 10 kW
230V heaters and to 7, 10, & 15 kW 460V and 575V
heaters. All other heaters MUST use a two-stage thermostat):
a.
TABLE 31:ELECTRIC HEAT LIMIT CONTROL SETTING
VOLTAGE
230-1-60
Upon a call for heat by the thermostat, the heater
sequencer (1S) will be energized. After completing
the specified fan on delay for heating, the UCB will
energize the blower motor.
The thermostat will cycle the electric heat to satisfy
the heating requirements of the conditioned space.
1
140
7
1,3
140
10
1,2,3
140
15
2,4,6
140
1,2,3,4,5
140
6
150
30
1,2,3,4,5,6
150
5
1,2,3
140
7
1,2,3
140
10
1,2,3
150
15
2,4,6
140
20
1,2,3,4,5,6
150
1,3,5
160
30
Two-stage heating (applies only to 15, 20 and 30 kW
230V heaters and 20 and 30 kW heater 460V and
575V heaters.):
a.
Upon a call for first-stage heat by the thermostat, the
heater sequencer (1S) (15, 20, 30 kW 230 volt) and
contactor (2M) (20, 30 kW 460 and 575 volt) will be
energized. After completing the specified fan on
delay for heating, the UCB will energize the blower
motor.
If the second stage of heat is required, heater
sequencer (2S) (12, 20, 30 kW 230 volt) or contactor (3M) (20, 30 kW 460 and 575 volt) will be energized. After completing the specified fan on delay for
heating, the UCB will energize the blower motor.
b.
The thermostat will cycle the electric heat to satisfy
the heating requirements of the conditioned space.
460-3-60
575-3-60
º
TEMPERATURE LIMIT SWITCH Open Temp F
5
20
230-3-60
b.
kW
2,4,6
150
7
2,4,6
140
10
2,4,6
140
15
2,4,6
140
20
3
160
30
3
150
10
2,4,6
140
15
2,4,6
140
20
5
160
30
5
150
RESET
Remove the call for heating by lowering the thermostat
setting lower than the conditioned space temperature.
This resets any flash codes.
HEAT ANTICIPATOR SETPOINTS
SAFETY CONTROLS
The control circuit includes the following safety controls:
1. Temperature Limit Switch (TLS) - This control is
located inside the heater compartment and is set to
open at the temperature indicated in the Electric
Heat Limit Control Setting Table 31. It resets automatically. The limit switch operates when a high
temperature condition, caused by inadequate supply air flow occurs, thus shutting down the heater
and energizing the blower.
46
It is important that the anticipator setpoint be correct.
Too high of a setting will result in longer heat cycles and
a greater temperature swing in the conditioned space.
Reducing the value below the correct setpoint will give
shorter “ON” cycles and may result in the lowering of
the temperature within the conditioned space. Refer to
Table 32 for the required heat anticipator setting.
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 32:ELECTRIC HEAT ANTICIPATOR SETPOINTS
HEATER
KW
5
7
10
15
20
30
7
10
15
20
30
10
15
20
30
VOLTAGE
230-3-60
460-3-60
575-3-60
SETTING, AMPS
TH1
TH2
0.35
0.35
0.35
0.35
0.19
0.35
0.38
0.35
0.38
0.35
0.35
0.35
0.37
0.29
0.37
0.29
0.35
0.35
0.37
0.29
0.37
0.29
GAS HEATING SEQUENCE OF OPERATION
When there is a W1 call for heat, the heat relay (RW1)
is energized by the unit control board (UCB). The
RW1-1 contacts immediately close energizing the ignition control board (ICB). The ICB checks the state of
the flame sense circuit, the roll out switch, the centrifugal switch and the primary / auxiliary temperature limit
switch circuit. If they are in the expected state, then the
ICB energizes the draft motor and verifies that the centrifugal switch located on the end of the draft motor
closes. After the centrifugal switch closes, a 15 second
heat exchanger purging period is completed. After this
purging period, the ICB will simultaneously energize
the pilot gas valve and the ignition coil. Once the flame
sensor senses a pilot flame is present, the ignition coil
is de-energized. The ICB checks for pilot flame stability
and once the ICB is satisfied that the pilot flame is stable, the main gas valve is energized by the ICB. The
UCB will energize the indoor blower after a 45 second
delay from the call for heat. The ICB and UCB both
monitor the furnace safety devices during the furnace
operation. When the call for heat is satisfied, the ICB
closes the pilot and main gas valves and performs a 30
second purging of the heat exchanger by continuing
the operation of the draft motor. The UCB continues
the operation of the indoor blower for a configurable
amount of time after the call for heat is satisfied.
Johnson Controls Unitary Products
REDUNDANT
VALVE
MAIN VALVE
GAS MAIN
GAS
VALVE
TO PILOT BURNER
TO MAIN
BURNER
FIGURE 18 - GAS VALVE PIPING
TWO STAGE FURNACE ONLY
If a W1 only call for heat from a two stage thermostat is
present, then a two stage furnace will start on high fire
for 1 minute and then reduce to low fire until the call for
heat is satisfied or a W2 call for heat is received. If a
W2 call for heat is received while in low fire operation,
then the ICB will immediately move to high fire operation. If a W1 and W2 call for heat is present, then the
furnace will remain on high fire operation until the W2
call for heat is satisfied.
Automatic staging of a two stage furnace using a single
stage thermostat is possible. To achieve automatic
staging of a two stage furnace using a single stage
thermostat, cut the 440/GY wire that runs from pin 2 of
the S3 connector on the (UCB) unit control board to P24 on the ignition control board. Cut the wire 1/2” from
the S3 mate-n-lock connector. Wire nut or tape off the
1/2” wire. Attach the other end of the 440/GY wire to
the R terminal on the UCB, or to the TB1 power strip.
The unit will operate the same as a W1 only call for
heat for 10 minutes. If the call for heat is not satisfied in
the 10 minutes, then the ICB will move to high fire
operation until the W1 call for heat has been satisfied.
GAS HEAT OPERATION ERRORS
During furnace operation, the ICB monitors the flame
sense circuit, the centrifugal switch, the primary limit
switch and the roll out switch. If a signal from any of the
inputs moves to a fault state, then the ICB immediately
closes the pilot and main gas valves. The ICB will
determine the device that is signaling a fault and flash
a code for that device. A primary limit trip, centrifugal
switch trip or flame sense fault triggers a temporary
lock out. An auxiliary limit or a roll out switch trip
requires intervention to reset the ICB. The UCB also
monitors the primary limit and gas valve.
47
362246-YIM-C-0109
TEMPERATURE LIMITS
The primary limit is located such that the temperature
sensitive switch can sense the temperature of the heat
exchanger tubes. On single stage models the limit is
mounted to the condenser partition panel. On two
stage models the limit is mounted just above the inlet of
the heat exchanger tubes on the right side. If a primary
limit (LS) fault occurs (the primary limit opens due to
excessive heat exchanger temperature), then the ICB
will flash the appropriate code (Table 37) and monitor
the primary limit. The UCB will energize the indoor
blower and the ICB will energize the draft motor while
the primary limit is open. When the primary limit closes
and the call for heat still exists, the ICB will start the
ignition sequence over and the UCB will de-energize
the blower for 45 seconds. However, the auxiliary limit
is in series with the primary limit and it takes first control. If the excessive heat has been high enough to
cause the auxiliary limit (AUX) to open, then the ICB
will flash the primary limit code but the furnace will not
retry ignition during the same call for heat. The auxiliary limit is of the manual reset type and is mounted in
the upper right hand corner of the panel between the
burner manifold and the flue gas collector box just
behind the draft motor. If the auxiliary switch has
opened, then special attention should be paid to the
primary limit as it may be faulty as well. However, the
auxiliary switch is sized such that multiple trips of the
primary limit due to complete blower failure will cause
enough heat to build up and trip the auxiliary.
forces the indoor blower on for the indoor blower heating off delay.
The gas valve is of the redundant type. If for any reason the main gas valve fails in the open position, then
the redundant valve ahead of the main gas valve will
shut off the flow of gas to both the pilot and main gas
valves.
CENTRIFUGAL SWITCH
The centrifugal switch is mounted on the end of the
draft motor and it is an integral part of the motor
assembly. On a call for heat, the ICB checks the centrifugal switch (CS) for open state before it energizes
the draft motor. If it is closed, then the ICB will lock out
the furnace and flash a code (Table 37). If open, then
the ICB will energize the draft motor and verify that the
switch closes before initiating the purging and ignition
sequence. If at any time during furnace operation the
centrifugal switch opens, then the ICB will de-energize
the pilot and main gas valves and monitor the centrifugal switch. If the centrifugal switch closes and the call
for heat still exists, then the ICB will retry the purging
and ignition sequence.
ROLLOUT SWITCH
If the primary limit opens three times within one hour,
then the UCB will lock on the indoor blower and flash a
fault code (Table 36).
This temperature sensitive switch is located in the
burner vestibule just above the right hand side of the
burner assembly. In the event of the flame spilling out
into the burner manifold area the rollout switch will
open, the ICB will close both the main and pilot gas
valves and flash a code (Table 37). The ICB will not
retry the ignition sequence during the same call for
heat.
GAS VALVE
FLAME SENSE CIRCUIT
The UCB monitors the gas valve (GV). Any time the
UCB senses voltage at the GV without a call for heat
for a continuous five-minute period, the UCB will lock
on the indoor blower and a flash code on the UCB is
initiated (Table 36). When the UCB no longer senses
voltage at the GV the UCB will de-energize the indoor
blower after the expiration of the indoor blower heating
off delay.
The flame sensor is mounted on the left hand side of
the burner assembly and is positioned such that the
pilot flame surrounds the tip of the sensor. On a call for
heat the ICB checks for the flame sense circuit to be
open. If open, then the ICB initiates the purging and
ignition sequence. Once the pilot flame is present, the
ICB monitors the flame sense circuit for pilot flame stability. If the pilot flame is unstable or lost completely,
then the ICB will immediately close both the pilot and
main gas valves. The ICB will retry the purging and
ignition sequence. If the flame is unstable or lost more
than 16 times during the same call for heat, then the
ICB will lock out furnace operation for 5 minutes.
If the voltage has been sensed at the GV for at least 15
seconds during the fan on delay for heating and the
UCB no longer senses voltage at the GV (W1 call for
heat removed or an ICB fault exists), then the UCB
48
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 33:SINGLE STAGE GAS HEAT LIMIT CONTROL
SETTING
Unit
(Tons)
3
3
4
4
5
5
Capacity, MBH
Input
Output
50
40
100
80
75
60
125
100
100
80
125
100
Limit Control Opens, °F
Direct Drive
Belt Drive
240
240
170
210
210
240
165
210
170
210
165
210
TABLE 34:2 STAGE GAS HEAT LIMIT CONTROL SETTING
1st Stage
2nd Stage
Capacity
Capacity
Unit
(Tons) Input Output Input Output
(MBH) (MBH) (MBH) (MBH)
3
45
36
75
61
3
69
55
115
92
4
45
36
75
61
4
75
60
125
101
5
45
36
75
61
5
75
60
125
101
Limit Control Opens,
°F
Direct
Belt
Drive
Drive
210
240
200
200
210
240
165
210
210
210
165
210
START-UP (COOLING)
PRESTART CHECK LIST
After installation has been completed:
1. Check the electrical supply voltage being supplied.
Be sure that it is the same as listed on the unit
nameplate.
2. Set the room thermostat to the off position.
3. Turn unit electrical power on.
4. Set the room thermostat fan switch to on.
5. Check indoor blower rotation.
•
If blower rotation is in the wrong direction.
Refer to Phasing Section in general information section.
•
Check blower drive belt tension.
6. Check the unit supply air (CFM). See “CHECKING
SUPPLY AIR CFM” on page 42.
7. Measure evaporator fan motor's amp draw.
FLASH CODES
8. Set the room thermostat fan switch to off.
The UCB will initiate a flash code associated with
errors within the system. Refer to UNIT CONTROL
BOARD FLASH CODES Table 39.
9. Turn unit electrical power off.
1. Turn unit electrical power on.
RESETS
Remove the call for heating by lowering the thermostat
setting lower than the conditioned space temperature.
This resets any flash codes.
HEAT ANTICIPATOR SETPOINTS
It is important that the anticipator setpoint be correct.
Too high of a setting will result in longer heat cycles
and a greater temperature swing in the conditioned
space. Reducing the value below the correct setpoint
will give shorter “ON” cycles and may result in the lowering of the temperature within the conditioned space.
TABLE 35:GAS HEAT ANTICIPATOR SETPOINTS
Gas Valve
Honeywell VR8204M
White-Rodgers 36E36
OPERATING INSTRUCTIONS
Anticipator Setpoint
0.60 amp
0.54 amp
2. Set the room thermostat setting to lower than the
room temperature.
3. Compressor will energize after the built-in time
delay (five minutes).
POST START CHECK LIST
1. Verify proper system pressures.
2. Measure the temperature drop across the evaporator coil.
3. Measure the system Amperage draw across all
legs of 3 phase power wires.
4. Measure the condenser fan amp draw.
SHUT DOWN
1. Set the thermostat to highest temperature setting.
2. Turn off the electrical power to the unit.
Johnson Controls Unitary Products
49
362246-YIM-C-0109
START-UP (GAS HEAT)
1. Check for gas leaks in the unit piping as well as the
supply piping.
PRE-START CHECK LIST
Complete the following checks before starting the unit.
1. Check the type of gas being supplied. Be sure that
it is the same as listed on the unit nameplate.
FIRE OR EXPLOSION HAZARD
2. Make sure that the vent and combustion air hoods
have been properly installed.
Failure to follow the safety warning exactly
could result in serious injury, death or property
damage.
OPERATING INSTRUCTIONS
This furnace is equipped with an intermittent
pilot and automatic re-ignition system. DO
NOT attempt to manually light the pilot.
TO LIGHT PILOT AND MAIN BURNERS:
1. Turn “off” electric power to unit.
2. Turn room thermostat to lowest setting.
3. Turn gas valve knob or switch to “on” position.
4. Turn “on” electric power to unit.
Never test for gas leaks with an open flame.
use a commercially available soap solution
made specifically for the detection of leaks to
check all connections. A fire or explosion may
result causing property damage, personal
injury or loss of life.
2. Check for correct manifold gas pressures. See
“Checking Gas Input” on page 52.
3. Check the supply gas pressure. It must be within the
limits shown on rating nameplate. Supply pressure
should be checked with all gas appliances in the
building at full fire. At no time should the standby
gas line pressure exceed 13", nor the operating
pressure drop below 5.0" for natural gas units. If gas
pressure is outside these limits, contact the local
gas utility for corrective action.
5. Set room thermostat to desired temperature. (If
thermostat “set” temperature is above room temperature, pilot burner ignition will occur and, after
an interval to prove pilot flame, main burners will
ignite).
TO SHUT DOWN:
1. Turn “off” electric power to unit.
2. Depress knob of gas valve while turning to “off”
position or position the switch to the “off” position.
POST-START CHECK LIST (GAS)
FIGURE 19 - TYPICAL SINGLE STAGE GAS VALVES
After the entire control circuit has been energized and
the heating section is operating, make the following
checks:
50
Johnson Controls Unitary Products
362246-YIM-C-0109
B U R N E R A S S E M B L Y B R A C K E T
REGULATOR ADJ. “HI”
(UNDER SCREW)
REGULATOR ADJ. “LO”
(UNDER SCREW)
F L A M E S E N S O R B U L B
“ON” - “OFF” CONTROL
1 /8 " G A P B E T W E E N C A R R Y -O V E R
T U B E A N D F L A M E S E N S O R B U L B
C A R R Y -O V E R T U B E
FIGURE 21 - PROPER FLAME ADJUSTMENT
PILOT CHECKOUT
HONEYWELL
VR820RQ
PILOT ADJ.
(UNDER SCREW)
FIGURE 20 - TYPICAL 2 STAGE GAS VALVES
MANIFOLD GAS PRESSURE ADJUSTMENT
Adjustments to the high-fire and low-fire (2 stage) gas
flow may be made by turning the pressure regulator
adjusting screws on the automatic gas valve.
Adjust as follows:
1. Remove the adjustment screw cap(s) on the regulator.
2. To decrease the gas pressure, turn the adjusting
screw counterclockwise.
The pilot flame should envelope the end of the flame
sensor. To adjust pilot flame, (1) remove pilot adjustment cover screw, (2) increase or decrease the clearance for air to the desired level, (3) be sure to replace
cover screw after adjustment to prevent possible gas
leakage.
Put the system into operation and observe through
complete cycle to be sure all controls function properly.
BURNER INSTRUCTIONS
To check or change burners, pilot or orifices, CLOSE
MAIN MANUAL SHUT-OFF VALVE AND SHUT OFF
ALL ELECTRIC POWER TO THE UNIT.
1. Remove the screws holding either end of the manifold to the burner supports.
3. To increase the gas pressure, turn the adjusting
screw clockwise.
2. Open the union fitting in the gas supply line just
upstream of the unit gas valve and downstream
from the main manual shut-off valve.
4. Replace adjustment screw caps.
3. Remove the gas piping closure panel.
NOTE: The factory set high-fire manifold pressure for
4. Disconnect wiring to the gas valves and spark ignitors. Remove the manifold-burner gas valve
assembly by lifting up and pulling back.
these furnaces is 3.50 IWG. The actual manifold pressure depends on the local fuel heating
value.
Johnson Controls Unitary Products
51
362246-YIM-C-0109
TABLE 36:GAS RATE - CUBIC FEET PER HOUR1
FIGURE 22 - TYPICAL FLAME APPEARANCE
Burners are now accessible for service.
Reverse the above procedure to replace the assemblies. Make sure that burners are level and seat at the
rear of the heat exchanger.
BURNER AIR SHUTTER ADJUSTMENT
Adjust burner shutters so no yellow flame is observed
in the heat exchanger tubes.
CHECKING GAS INPUT
NATURAL GAS
1. Turn off all other gas appliances connected to the
gas meter.
2. With the furnace turned on, measure the time
needed for one revolution of the hand on the smallest dial on the meter. A typical gas meter usually
has a 1/2 or a 1 cubic foot test dial.
3. Using the number of seconds for each revolution
and the size of the test dial increment, find the
cubic feet of gas consumed per hour from the Gas
Rate - Cubic Feet Per Hour (Table 36).
If the actual input is not within 5% of the furnace rating
(with allowance being made for the permissible range
of the regulator setting), replace the orifice spuds with
spuds of the proper size.
NOTE: To find the Btu input, multiply the number of
cubic feet of gas consumed per hour by the
Btu content of the gas in your particular locality
(contact your gas company for this information
- it varies widely from city to city.)
52
Size of Test Dial
Seconds for one
rev.
1/2 cu. ft.
1 cu. ft.
10
180
360
12
150
300
14
129
257
16
113
225
18
100
200
20
90
180
22
82
164
24
75
150
26
69
138
28
64
129
30
60
120
32
56
113
34
53
106
36
50
100
38
47
95
40
45
90
42
43
86
44
41
82
46
39
78
48
37
75
50
36
72
52
35
69
54
34
67
56
32
64
58
31
62
60
30
60
1. By actual measurement, it takes 38 seconds for the hand on
the 1-cubic foot dial to make a revolution with a 100,000
Btuh furnace running. Using this information, located 38
seconds in the first column in the table above. Read across
to the column headed “1 Cubic Foot”, where you will see
that 95 cubic feet of gas per hour are consumed by the furnace at that rate. Multiply 95 X 1050 (the Btu rating of the
gas obtained from the local gas company). The result is
99,750 Btuh, which is close to the 100,000 Btuh rating of the
furnace.
ADJUSTMENT OF TEMPERATURE RISE
The temperature rise (or temperature difference
between the return air and the heated air from the furnace) must lie within the range shown on the rating
plate and the data in the Gas Heat Application Table 4.
Johnson Controls Unitary Products
362246-YIM-C-0109
CFM =
Btuh Input x 0.8
108
. x oF Temp. Rise
After the temperature rise has been determined, the
cfm can be calculated as follows:
After about 20 minutes of operation, determine the furnace temperature rise. Take readings of both the return
air and the heated air in the ducts (about six feet from
the furnace) where they will not be affected by radiant
heat. Increase the blower cfm to decrease the temperature rise; decrease the blower cfm to increase the
rise. Refer to the Blower Motor and Drive Data
Table 29.
TROUBLESHOOTING
COOLING TROUBLESHOOTING GUIDE
2. If the blower motor runs with the fan switch in the
ON position but will not run after the compressor
has energized when the fan switch is in the AUTO
position, check the room thermostat for contact
between R and G in the AUTO position during calls
for cooling.
3. If the supply air blower motor does not energize
when the fan switch is set to ON, check that line
voltage is being supplied to the contacts of the M2,
contactor, and that the contactor is pulled in. Check
for loose wiring between the contactor and the supply air blower motor.
4. If M2 is pulled in and voltage is supplied to M2,
lightly touch the supply air blower motor housing. If
it is hot, the motor may be off on internal protection. Cancel any thermostat calls and set the fan
switch to AUTO. Wait for the internal overload to
reset. Test again when cool.
5. If M2 is not pulled in, check for 24 volts at the M2
coil. If 24 volts are present at M2 but M2 is not
pulled in, replace the contactor.
Troubleshooting of components may require
opening the electrical control box with the power
connected to the unit. Use extreme care when
working with live circuits! Check the unit
nameplate for the correct line voltage and set
the voltmeter to the correct range before making
any connections with line terminals.
Shut off all electric power to the unit prior to
any of the following maintenance procedures
to prevent personal injury.
Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation, which
could cause injury to person and/or damage
unit components. Verify proper operation after
servicing.
6. Failing the above, if there is line voltage supplied at
M2, M2 is pulled in, and the supply air blower
motor still does not operate, replace the motor.
7. If 24 volts is not present at M2, check that 24 volts
is present at the UCB supply air blower motor terminal, “FAN”. If 24 volts is present at the FAN,
check for loose wiring between the UCB and M2.
8. If 24 volts is not present at the “FAN” terminal,
check for 24 volts from the room thermostat. If 24
volts are not present from the room thermostat,
check for the following:
a.
Proper operation of the room thermostat (contact
between R and G with the fan switch in the ON position and in the AUTO position during operation calls).
b.
Proper wiring between the room thermostat and the
UCB.
c.
Loose wiring from the room thermostat to the UCB.
On calls for cooling, if the compressors are operating
but the supply air blower motor does not energize after
a short delay (the room thermostat fan switch is in the
“AUTO” position).
9. If 24 volts is present at the room thermostat but not
at the UCB, check for proper wiring between the
thermostat and the UCB, i.e. that the thermostat G
terminal is connected to the G terminal of the UCB,
and for loose wiring.
1. Turn the thermostat fan switch to the ON position.
If the supply air blower motor does not energize, go
to Step 3.
10. If the thermostat and UCB are properly wired,
replace the UCB.
Johnson Controls Unitary Products
53
362246-YIM-C-0109
On a call for cooling, the supply air blower motor is
operating but the compressor is not (the room thermostat fan switch is in the “AUTO” position).
1. If installed, check the position of the economizer
blades. If the blades are open, the economizer is
providing free cooling and the compressors will not
immediately operate. If both stages of cooling are
requested simultaneously and the economizer provides free cooling, following a short delay the compressor will be energized unless it is locked out,
unless this option has been disabled through computer communications.
2. If no economizer is installed or the economizer is
not opening to provide free cooling and the compressor does not energize on a call for cooling,
check for line voltage at the compressor contactor,
M1, and that the contactor is pulled in. Check for
loose wiring between the contactor and the compressor.
3. If M1 is pulled in and voltage is supplied at M1,
lightly touch the compressor housing. If it is hot, the
compressor may be off on inherent protection.
Cancel any calls for cooling and wait for the internal overload to reset. Test again when cool.
4. If M1 is not pulled in, check for 24 volts at the M1
coil. If 24 volts are present and M1 is not pulled in,
replace the contactor.
5. Failing the above, if voltage is supplied at M1, M1
is pulled in, and the compressor still does not operate, replace the compressor.
6. If 24 volts is not present at M1, check for 24 volts at
the UCB terminal, C1. If 24 volts is present, check
for loose wiring between C1 and the compressor
contactor.
7. If 24 volts is not present at the C1 terminal, check
for 24 volts from the room thermostat at the UCB
Y1 terminal. If 24 volts is not present from the room
thermostat, check for the following:
a.
24 volts at the thermostat Y1 terminal
b.
Proper wiring between the room thermostat and the
UCB, i.e. Y1 to Y1, Y2 to Y2
c.
Loose wiring from the room thermostat to the UCB.
8. If 24 volts is present at the UCB Y1 terminal, the
compressor may be out due to an open high-pressure switch, low-pressure switch, or freezestat.
Check for 24 volts at the HPS1, LPS1, and FS1
54
terminals of the UCB. If a switch has opened, there
should be a voltage potential between the UCB terminals, e.g. if LPS1 has opened, there will be a 24volt potential between the LPS1 terminals.
9. If 24 volts is present at the UCB Y1 terminal and
none of the protection switches have opened, the
UCB may have locked out the compressor for
repeat trips. The UCB should be flashing an alarm
code. If not, press and release the ALARMS button
on the UCB. The UCB will flash the last five alarms
on the LED. If the compressor is locked out, cancel
any call for cooling. This will reset any compressor
lock outs.
NOTE: While the above step will reset any lockouts,
the compressor may be held off for the ASCD.
See the next step.
10. If 24 volts is present at the UCB Y1 terminal and
none of the switches are open and the compressor
is not locked out, the UCB may have the compressor in an ASCD. Check the LED for an indication of
an ASCD cycle. The ASCD should time out within
5 minutes. Press and release the TEST button to
reset all ASCDs.
11. If 24 volts is present at the UCB Y1 terminal and
the compressor is not out due to a protective
switch trip, repeat trip lock out, or ASCD, the economizer terminals of the UCB may be improperly
wired. Check for 24 volts at the Y1 “OUT” terminal
of the UCB. If 24 volts is present, trace the wiring
from Y1 “OUT” for incorrect wiring. If 24 volts is not
present at the Y1 “OUT” terminal, the UCB must be
replaced.
12. For units without economizers: If 24 volts is present at the Y1 OUT terminal, check for 24 volts at
the Y1 “ECON” terminal. If 24 volts is not present,
check for loose wiring from the Y1 “OUT” terminal
to the Mate-N-Lock plug, the jumper in the Mate-NLock plug, and in the wiring from the Mate-N-Lock
plug to the Y1 “ECON” terminal.
13. For units with economizers: If 24 volts is present at
the Y1 “OUT” terminal, check for 24 volts at the Y1
“ECON” terminal. If 24 volts is not present, check
for loose wiring from the Y1 “OUT” terminal to the
Mate-N-Lock plug, a poor connection between the
UCB and economizer Mate-N-Lock plugs, loose
wiring from the Mate-N-Lock plug to the economizer, back to the Mate-N-Lock plug, and from the
Mate-N-Lock plug to the Y1 “ECON” terminal. If
Johnson Controls Unitary Products
362246-YIM-C-0109
nothing is found, the economizer actuator may
have faulted and is failing to return the 24-volt “call”
to the Y1 “ECON” terminal even though the economizer is not providing free cooling. To test, disconnect the Mate-N-Locks and jumper between the
WHITE and YELLOW wires of the UCB’s Mate-NLock plug. If the compressor energizes, there is a
fault in the economizer wiring or actuator.
For units without factory installed or with field
installed economizers, the UCB allows compressor
operation all the time. This programming can be
checked or changed by the local distributor.
15. If none of the above correct the error, replace the
UCB.
CHARGING THE UNIT
14. The UCB can be programmed to lock out compressor operation during free cooling and in low ambient conditions. These options are not enabled by
default. Local distributors can test the UCB for this
programming.
These units will be charged using the superheat
method. Superheat charging data is shown in Tables
37 and 38. When charging each system, superheat
data should be taken at the compressor inlet.
For units with factory installed economizers, the
UCB is programmed to lock out compressor operation when the LAS set point is reached.
TABLE 37:DJ036 COOLING SUPERHEAT CHARGING TABLE
SUPERHEAT AT COMPRESSOR SUCTION (°F)
AIRFLOW=1200 CFM
OUTDOOR TEMP
(°F)
INDOOR WET BULB TEMPERATURE (°F)
55
57
59
61
63
65
67
69
71
73
75
65
32.2
32.6
33.0
33.4
33.8
34.2
34.6
35.4
36.3
36.7
37.1
70
23.3
24.7
26.1
27.5
28.9
30.3
31.7
32.8
33.9
34.5
35.0
75
14.3
16.8
19.2
21.6
24.0
26.4
28.8
30.2
31.6
32.3
32.9
80
5.4
8.8
12.2
15.7
19.1
22.5
25.9
27.6
29.2
30.0
30.9
85
-
-
5.3
9.7
14.2
18.6
23.0
24.9
26.8
27.8
28.8
90
-
-
-
7.6
11.2
14.7
18.3
21.1
23.9
25.4
26.8
95
-
-
-
5.5
8.1
10.8
13.5
17.3
21.0
22.9
24.8
100
-
-
-
-
6.3
8.3
10.3
14.0
17.8
19.7
21.6
105
-
-
-
-
-
5.7
7.0
10.8
14.6
16.5
18.4
110
-
-
-
-
-
-
-
7.6
11.4
13.3
15.2
115
-
-
-
-
-
-
-
-
8.2
10.1
12.0
TABLE 38:DJ048 COOLING SUPERHEAT CHARGING TABLE
SUPERHEAT AT COMPRESSOR SUCTION (°F)
AIRFLOW=1600 CFM
OUTDOOR TEMP
(°F)
INDOOR WET BULB TEMPERATURE (°F)
55
57
59
61
63
65
67
69
71
73
75
65
36.9
37.0
37.1
37.2
37.3
37.4
37.5
37.7
37.8
37.9
38.0
70
31.1
31.8
32.5
33.1
33.8
34.5
35.1
35.5
35.9
36.1
36.3
75
25.4
26.6
27.8
29.1
30.3
31.5
32.8
33.4
34.0
34.3
34.6
80
19.6
21.4
23.2
25.0
26.8
28.6
30.4
31.2
32.1
32.5
32.9
85
13.8
16.2
18.6
20.9
23.3
25.6
28.0
29.1
30.2
30.7
31.2
90
6.9
9.5
12.1
14.7
17.3
19.9
22.6
25.1
27.6
28.8
30.1
95
-
-
5.7
8.5
11.4
14.2
17.1
21.0
24.9
26.9
28.9
100
-
-
5.0
7.1
9.3
11.4
13.5
16.6
19.6
21.2
22.7
105
-
-
-
5.8
7.1
8.5
9.9
12.1
14.3
15.4
16.5
110
-
-
-
-
5.0
5.7
6.3
7.6
9.0
9.7
10.3
115
-
-
-
-
-
-
-
-
-
-
-
The DJ060 uses a TXV. Charge the unit to 12°F subcooling.
Johnson Controls Unitary Products
55
362246-YIM-C-0109
NORMAL OPERATING PRESSURES
290
115°F Outdoor
Discharge Pressure (psig)
270
105°F Outdoor
250
230
95°F Outdoor
210
190
85°F Outdoor
170
75°F Outdoor
150
65°F Outdoor
130
60
65
70
75
80
85
90
95
100
105
Suction Pressure (psig)
FIGURE 23 - DJ036 OPERATING PRESSURES
310
115°F Outdoor
Discharge Pressure (psig)
290
270
105°F Outdoor
250
230
95°F Outdoor
210
85°F Outdoor
190
170
75°F Outdoor
150
65°F Outdoor
130
65
70
75
80
85
90
95
100
Suction Pressure (psig)
FIGURE 24 - DJ048 OPERATING PRESSURES
56
Johnson Controls Unitary Products
362246-YIM-C-0109
330
115°F Outdoor
Discharge Pressure (psig)
310
290
105°F Outdoor
270
250
95°F Outdoor
230
85°F Outdoor
210
190
75°F Outdoor
170
65°F Outdoor
150
65
70
75
80
85
90
95
100
Suction Pressure (psig)
FIGURE 25 - DJ060 OPERATING PRESSURES
GAS HEAT TROUBLESHOOTING GUIDE
Troubleshooting of components may require
opening the electrical control box with the power
connected to the unit. Use extreme care when
working with live circuits! Check the unit
nameplate for the correct line voltage and set
the voltmeter to the correct range before making
any connections with line terminals.
When not necessary, shut off all electric power
to the unit prior to any of the following maintenance procedures so as to prevent personal
injury.
Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation, which
could cause injury to person and/or damage
unit components. Verify proper operation after
servicing.
Johnson Controls Unitary Products
The furnace may shut down on a high temperature condition during the procedure. If this
occurs, the UCB energize the supply air blower
motor until the high temperature limit has
reset. Caution should be used at all times as
the supply air blower may energize regardless
of the room thermostat fan switch position.
Before beginning symptomatic troubleshooting activities read the flash code LEDs on the unit control board
(UCB) and the ignition control board (ICB). Fault codes
have a quick sequence of flashes indicating the flash
code number followed by a pause with the LED off. The
ICB flash codes are repeated until the fault is cleared.
The ICB monitors itself, the centrifugal switch, lockout
due to > 16 pilot flame losses, primary limit, rollout and
a flame present when the ICB expects no flame.
With power applied to the unit, if the LED on the ICB is
flashing the heartbeat and the furnace will not operate,
then proceed to the symptomatic troubleshooting section. If the ICB LED is not flashing, then perform the ICB
troubleshooting procedures. If the ICB has a flash code
other than the heartbeat, then determine the flash code
and locate its troubleshooting procedures in the flash
code troubleshooting section. Refer to Table 37 for flash
code identification and component causing fault.
57
362246-YIM-C-0109
FLASH CODE TROUBLESHOOTING
Power to the unit should be interrupted during the troubleshooting of individual components unless otherwise
indicated. All troubleshooting procedures assume the
unit is wired per the wiring diagram. If there is any indication the unit has been previously repaired, then the
first priority is to verify that the furnace is wired per the
wiring diagram. Miss-wired units will give false flash
codes.
IGNITION CONTROL BOARD
The ICB controls the ignition of the pilot, the opening
and closing of the gas valves and the operation of the
draft (inducer) motor. It also monitors all the furnace
safety components.
If the ICB LED is on steady, then verify the wiring of the
unit to the wiring diagram and if ok, then replace the
ICB. If the unit has power and the ICB LED is not flashing, then remove the 3 pin connector (single stage gas
heat) or 4 pin connector (2 stage gas heat) from the
ICB. Measure the control voltage between terminals 1
and 2 of the wiring harness connector. The control voltage must be between 18 and 30 volts. If control voltage
is not present, then check the 3.2A circuit breaker to
verify that the circuit breaker has control voltage on
both input and output terminals. If control voltage is
present on the input and not the output of the circuit
breaker, then reset or replace the circuit breaker as
necessary. If control voltage is present on both sides of
the circuit breaker, then check the power and common
wires between the unit control box and the ICB and
repair as necessary. If the control voltage is present,
then verify the cleanliness of the harness and the ICB
connector, clean if necessary and reconnect the wiring
harness to the ICB and observe ICB LED. If it now
flashes the heartbeat, then the fault was a bad connection between the harness connector and the ICB connector or a broken wire exists in the harness. With the
harness connected to the ICB, gently move the wires in
the harness while observing the ICB LED. If heartbeat
is steady, then verify proper operation of the furnace. If
the ICB does not flash the heartbeat, then gently move
the wires in the harness connector while observing the
ICB LED. If you get any flashes of the ICB LED, then
there is still a bad connection or a broken wire. If no
flashes are seen while gently moving the wires with the
harness connected to the ICB, then replace the ICB
and verify proper operation of the furnace.
58
CENTRIFUGAL SWITCH
The centrifugal switch is an integral part of the draft
motor. The centrifugal switch closes when the motor
speed increases to ~2500 rpm and opens when the
motor speed descends to ~2000 rpm.
If a flash code indicates the centrifugal switch is causing a fault, then
1. If the flash code indicates the switch is open with
the draft (inducer) motor on (flash code 2), then
a. Disconnect power to the unit. Using a screw
driver, spin the draft motor blower wheel. If
bound or dragging, then visually inspect the draft
motor blower wheel area for debris. If debris is
present, then clear debris and verify proper furnace operation. If clear, then replace the draft
motor and verify proper furnace operation.
b. Restore power to unit and induce a call for heat.
Measure the voltage across the two draft motor
leads (white and red on single stage models and
white and black on two stage models). If it is less
than 177 volts, then check and repair the power
circuit to the draft motor. If the voltage is greater
than 176 volts and the draft motor is not turning,
then disconnect power and draft motor power
leads. Measure the resistance of the draft motor
windings. If an open circuit exists in the motor,
then replace the draft motor. If the voltage is
greater than 176 volts and the motor is turning,
then check the centrifugal switch wiring between
the ICB and the draft motor. If ok, then disconnect power to the unit and place the gas valve in
the off position. Prepare to temporarily jumper
the wires connected to terminals 3 and 8 of the
ICB 9 pin harness connector by disconnecting
the draft motor leads from the 9 pin harness.
Restore the power to the unit and induce a call
for heat. Jumper wires 3 and 8. If the ignition
sequence is started after 15 seconds (audible
sparking of the igniter), then replace the draft
motor reconnecting the centrifugal switch wiring
per the wiring diagram. If not, then replace the
ICB, remove the jumper and reconnect the centrifugal switch wiring per the wiring diagram.
Place the gas valve in the on position and verify
proper furnace operation.
2. If the flash code indicates the switch is closed with
the draft (inducer) motor off (flash code 3), then
disconnect the 9 pin connector from the ICB and
measure the continuity of the centrifugal switch
with a battery powered test light or an ohm meter
between terminals 3 and 8 of the harness connec-
Johnson Controls Unitary Products
362246-YIM-C-0109
tor. If a closed circuit is indicated, then check the
wiring between the ICB and the draft motor. If the
wiring is not shorted together, then replace the
draft motor. If an open circuit is indicated, then
reconnect the 9 pin wiring harness to the ICB and
remove power to the unit for at least 20 seconds.
Restore power to the unit. If the ICB continues to
flash a code 3, then replace the ICB.
PILOT FLAME LOCKOUT
The ICB counts the number of flame losses during the
same call for heat. If more than 16 flame losses occur
within the same call for heat, then the control temporarily locks out furnace operation for 5 minutes (flash code
5). If the call for heat remains after the 5 minutes, then
the ICB will retry the ignition sequence. The flame
losses can be due to low inlet pressure, debris around
flame sensor, plugged pilot burner, soot on the surface
of the flame sensor or misadjusted pilot pressure.
Remove the power to the unit for 20 seconds and then
restore power to the unit. Induce a call for heat and
observe the pilot flame in the flame sensor area to
determine the best course of action.
1. If the flame is strong and stable in the flame sensor
area, then verify the position of the flame sensor
per the start up procedures. If ok, then remove the
flame sensor and check the cleanliness of the electrode. If clean, then replace the flame sensor and
adjust pilot per the start up procedures. If not
clean, then clean, reinstall and adjust pilot per the
start up procedures.
2. If the flame is weak or unstable in the flame sensor
area, then verify the gas inlet pressure. If gas inlet
pressure is above the minimum inlet pressure stated
on unit data label, then adjust the pilot pressure per
the start up procedures. If the pilot cannot be
adjusted to obtain a strong and stable flame in the
flame sensor area, then remove the burner assembly and verify the pilot burner assembly is open
internally and the holes in the burner are clean.
Check the pilot orifice size to the unit data plate and
the cleanliness of the pilot orifice. Verify that the
flame sensor electrode is clean and is adjusted
properly. After cleaning or replacement of the pilot
assembly components, reinstall the burner assembly and adjust pilot per the start up procedure.
PRIMARY OR AUX TEMPERATURE LIMIT
The temperature limits limit the temperature in the furnace to a safe level. If a temperature higher than the
Johnson Controls Unitary Products
preset limit is achieved due to low or no air flow
through the furnace, then the temperature limits opens
and the ICB closes the gas valve and flashes code 6.
The primary limit is automatic reset type while the auxiliary limit is manual reset type. If either one opens,
then the ICB removes power to the gas valve and the
UCB energizes the indoor blower until the primary limit
automatically resets or the auxiliary limit is manually
reset. Verify adequate air flow through the furnace. If
air flow is nonexistent or weak, then troubleshoot and
repair the conditioned space air circulation system as
necessary. Reset the auxiliary limit and verify proper
operation of the furnace. If airflow is normal, then verify
the gas input rate to the furnace following the start up
procedures (auxiliary limit must be reset before the furnace will operate). If after verifying the circulating air
system, the input rate to the furnace and that the air
temperature rise through the furnace is within the rise
range on the unit data plate the flash code still exists,
then set the gas valve to the off position and temporarily apply control voltage (~24 volts) to pin 9 of the 9 pin
ICB connector. With power applied to the unit, if the
ICB LED continues to flash a code 6, then replace the
ICB and return unit to operation (you must remove the
temporary voltage to pin 9 before the gas valve is
turned on). If the ICB LED flashes a heartbeat, then
replace the limit that is opening, remove the temporary
voltage applied to pin 9, turn on the gas valve, restart
the furnace and verify proper operation of the furnace.
ROLLOUT SWITCH
The rollout switch is installed to protect the furnace
from damage due to excessive heat in the burner area.
There are 4 main reasons the rollout switch will open
(flash code 7) due to excessive heat in the burner area.
You must remove power to the unit for 20 seconds to
reset the ICB.
1. A blocked flue outlet is the most common cause for
the rollout switch to open. Check the flue outlet for
debris and clear if necessary.
2. Loose blower wheel on draft motor. Verify that the
blower wheel is securely fastened to the draft
motor shaft.
3. Unit operating outside the air temperature rise
range stated on the unit data plate. Either the air
flow through the furnace is not sufficient or the gas
input rate to the furnace exceeds the recommended rate. Verify both conditions are within the
published ranges.
59
362246-YIM-C-0109
4. Cracked heat exchanger tube(s). If a heat
exchanger tube or tubes is cracked, then the flow
through the heat exchanger is restricted and the
flame will either roll out of the tube inlet or heat will
build to an abnormal level in the burner area. This
can usually be determined by observing burner
flame with and without indoor blower operation. If
the flame changes when the blower is running
compared to when it is not, then visually inspect
the heat exchanger tubes.
If all of the above are found to be in good condition or
within the operating ranges, then set the gas valve to
the off position and temporarily apply control voltage
(~24 volts) to pin 6 of the 9 pin ICB connector. With
power applied to the unit, if the ICB LED continues to
flash a code 7, then replace the ICB and return unit to
operation (you must remove the temporary voltage to
pin 6 before the gas valve is turned on). If the ICB LED
flashes a heartbeat, then replace the rollout switch,
remove the temporary voltage applied to pin 6, turn on
the gas valve, restart the furnace and verify proper
operation of the furnace.
UNEXPECTED FLAME PRESENCE
If a flame is present without a call for heat (flash code
8), then the ICB will continue operation of the draft
motor and the UCB will call for indoor operation when
either of the temperature limit opens. If the unit is correctly wired and there is not a call for heat, then check
for control voltage to the gas valve. If control voltage
exists at the gas valve, then replace the ICB. If voltage
is not present at the gas valve, then replace the gas
valve.
GAS VALVE STUCK OFF OR ON
If the pilot and/or the main valves are sensed to be off
more than 1 second when commanded to be on, the
control will shut off all outputs and enter a hard lockout
(flash code 9). Likewise, if the pilot and/or the main
valves are sensed to be on more than 1 second when
commanded to be off, the control will shut off all outputs and enter a hard lockout (flash code 9). The control will not respond to thermostat demands during a
hard lockout. The only way to recover from a hard lockout is to remove and reapply 24VAC power to the control.
hard lockout (flash code 10). The control will not
respond to thermostat demands during a hard lockout.
The only way to recover from a hard lockout is to
remove and reapply 24VAC power to the control. If
problem persists after removal and reapplication of
24VAC power, the board may need to be replaced.
SYMPTOMATIC TROUBLESHOOTING
On calls for heating, the draft motor operates and the
furnace lights but the supply air blower motor does not
energize after a short delay (the room thermostat fan
switch is in “AUTO” position).
1. Place the thermostat fan switch in the “ON” position. If the supply air blower motor energizes, go to
Step 10.
2. If the supply air blower motor does not energize
when the fan switch is set to “ON,” check that line
voltage is being supplied to the contacts of the M2
contactor, and that the contactor is pulled in. Check
for loose wiring between the contactor and the supply air blower motor.
3. If M2 is pulled in and voltage is supplied at M2,
lightly touch the supply air blower motor housing. If
it is hot, the motor may be off on inherent protection. Cancel any thermostat calls and set the fan
switch to “AUTO”, wait for the internal overload to
reset. Test again when cool.
4. If M2 is not pulled in, check for 24 volts at the M2
coil. If 24 volts is present at M2 but M2 is not pulled
in, replace the contactor.
5. Failing the above, if there is line voltage supplied at
M2, M2 is pulled in, and the supply air blower
motor still does not operate, replace the motor.
6. If 24 volts is not present at M2, check that 24 volts is
present at the supply air blower motor terminal on
the UCB. If 24 volts is present at the UCB terminal,
check for loose wiring between the UCB and M2.
7. If 24 volts is not present at the UCB supply air
blower motor terminal, check for 24 volts from the
room thermostat. If 24 volts is not present from the
room thermostat, check for the following:
a.
Proper operation of the room thermostat (contact
between R and G with the fan switch in the “ON”
position and in the “AUTO” position during operation
calls).
b.
Proper wiring between the room thermostat and the
UCB.
c.
Loose wiring from the room thermostat to the UCB.
FLAME SENSE CIRCUIT FAILURE
If the control detects an internal hardware failure in the
flame sense circuit, it shuts off all outputs and enters a
60
Johnson Controls Unitary Products
362246-YIM-C-0109
8. If 24 volts is present at the room thermostat but not
at the UCB, check for proper wiring between the
thermostat and the UCB, i.e. that the thermostat G
terminal is connected to the G terminal of the UCB,
and for loose wiring.
9. If the thermostat and UCB are properly wired,
replace the UCB.
10. If the blower motor runs with the fan switch in the
“ON” position but does not run shortly after the furnace has ignited when the fan switch is in the
“AUTO” position, check the room thermostat for
contact between R and G during “W1” calls.
On calls for heating, the supply air blower operates but
the draft motor does not (the room thermostat fan
switch is in the “AUTO” position).
1. The draft motor has inherent protection. If the
motor shell is hot to the touch, wait for the internal
overload to reset.
2. If the motor shell is cold with the room thermostat
calling for heat, check if 24 volts is present at the
room thermostat but not at the UCB, check for
proper wiring between the thermostat and the
UCB, i.e. that the thermostat “W1” terminal is connected to the “W1” terminal of the UCB, and for
loose wiring.
3. The draft motor is a 230 volt draft motor on all models regardless of unit supply voltage. If the ICB is
flashing a code other than the heartbeat, then troubleshoot the device indicated by the fault code. If
not, then remove power to the unit for more than
20 seconds. If upon restoring the power to the unit
the draft motor does not start with a call for heat,
then verify that terminal “L1” of the ICB has a minimum of 120 volts to ground on 230 and 460 volt
models or a minimum of 18 volts to ground on 575
volt models. If terminal “L1” does not have the minimum voltage, then check the wiring between the
unit control box and the ICB on all models and on
460 volt models, the transformer in the gas heat
compartment and its wiring. If terminal “L1” does
have the minimum voltage, then check for the minimum voltage on terminal “IND” of the ICB on single stage models and terminal “IND HIGH” of the
ICB on two stage models. If voltage is not present
at the terminal, then verify wiring between the control box and the ICB. If all wiring is intact, then ICB
is at fault. If voltage is present at the terminal on
230 and 460 volt models, then the draft motor is at
fault. On 575 volt models, if voltage is present at
the terminal, then check the draft motor relay
(DMR on single stage gas heat and DMR-2 on two
Johnson Controls Unitary Products
stage gas heat) mounted above the ICB. First verify that the relay is pulled in by visual inspection. If
not, then verify the minimum voltage is present
between terminals “A” and “B” of the relay. If the
minimum voltage is not present, then check the
wiring. If it is present, then verify that a minimum of
150 volts is present at terminals “5” and “7” of the
draft motor relay. If not present at terminal “7” of
the draft motor relay, then troubleshoot the transformer in blower section and its wiring. If present at
terminal “7” and not at terminal “5” of the draft
motor relay, then the relay is at fault. If the minimum voltage is present at terminal 5 of the draft
motor relay, then the draft motor is at fault.
The ignitor sparks at the pilot burner but the pilot does
not ignite and a gas odor is detected at the draft motor
outlet.
1. Adjust the pilot adjust screw on the gas valve as
described in “PILOT CHECKOUT” on page 51.
2. Check the supply pressure as described in “POST
START CHECK LIST” on page 50. Make adjustments as necessary.
3. Check the pilot orifice and pilot burner for obstruction as described in paragraph above. Clean as
needed but the problem should not be the gas
valve.
The pilot burner ignites but the ignitor continues to
spark and the main burners do not ignite.
1. Make the same checks and adjustment as
described in “PILOT CHECKOUT” on page 51.
2. Check the supply pressure as described in “POST
START CHECK LIST” on page 50. Make adjustments as necessary.
3. Make sure that the pilot burner is not bent or damaged.
4. Make sure that the ground connections at the pilot
burner, gas valve and ignition control are intact.
Check the ignitor wire for good electrical connection. If all are intact, replace the ignition control.
The pilot burner lights and the spark stops but the main
burners do not light.
1. Check electrical connections between the ignition
control and the gas valve. If intact, check for 24
61
362246-YIM-C-0109
Pressing the button two times within five seconds causes the control to flash its address.
volts across terminals “MV” and “GROUND” terminals. If no voltage detected, replace ignition control. If voltage is present, replace gas valve.
Pressing the button three times within five seconds forces the control to reset its address to
1, which is the factory default.
Main burners light but exhibit erratic flame characteristics.
1. Adjust air shutters as described in “BURNER AIR
SHUTTER ADJUSTMENT” on page 52.
2. Check the main burner orifices for obstruction and
alignment. Removal procedure is described in
BURNER INSTRUCTIONS on page 51. Clean or
replace burner orifices and burners as needed.
Current alarms or active restrictions are flashed on the
ICB LED. No history is stored on the ICB.
FAN ON AND OFF DELAYS
The fan ON and OFF delays can be field adjusted by
pressing a combination of buttons on the UCB.
UNIT FLASH CODES
•
Various flash codes are utilized by the unit control
board (UCB) and the ignition control board (ICB) to aid
in troubleshooting. Flash codes are distinguished by
the short on and off cycle used (approximately 200ms
on and 200ms off). To show normal operation, the control boards flashes a 1 second on, 1 second off “heartbeat” during normal operation. This is to verify that the
UCB and the ICB are functioning correctly. Do not confuse this with an error flash code. To prevent confusion, a 1-flash, flash code is not used.
Current alarms or active restrictions are flashed on the
UCB LED.
•
LAST ERROR - When this button is pressed
and released one time within five seconds, it
flashes the last five flash codes on the board’s
LED. The most recent alarm is shown first and
the oldest alarm is shown last.
When pressed and released twice within a five
second span, the fault history is cleared.
•
When this button is pressed twice within five
seconds, any active lockouts are reset.
62
then release. The control flashes three times
as it writes a 30 second delay ON and a 90
second delay OFF to the program.
•
Gas Heat Option #2 - Press the COMM SETUP
and TEST RESET buttons simultaneously and
then release. The control flashes four times as
it writes a 30 second delay ON and a 180 second delay OFF to the program.
•
Electric Heat - Press and release the COMM
SETUP and LAST ERROR buttons at the same
time. The control flashes twice on the LED as
the control writes a 0 second ON and a 30 second OFF fan delay to the control’s program
memory.
Comm Setup
Button
TEST RESET - When this button is pressed and
released one time within five seconds, any
anti-short cycle delays (ASCD) is by-passed
for one cycle.
•
Gas Heat Option #1 - Press the LAST ERROR
and TEST RESET buttons simultaneously and
Last Error
Button
Test Reset
Button
COMM SET UP - If the board is to be networked
with other units, this button is used to set the
network address.
Control Board
LED
The first time the button is pressed within five
seconds, it scans the bus, then assigns itself
the first available address {starts at 2}. It then
flashes that address one time.
FIGURE 26 - UNIT CONTROL BOARD
Johnson Controls Unitary Products
362246-YIM-C-0109
TABLE 39:UNIT CONTROL BOARD FLASH CODES
Flash Code
Description
On Steady
Control Failure - Replace Control
Heart Beat
Normal Operation
1 Flash
Not Applicable
ASCD1
TABLE 40:IGNITION CONTROL BOARD FLASH CODES
Flash Code
Heart Beat
1 Flash
Description
Normal Operation
Not Applicable
2 Flashes
Pressure / Centrifugal Switch Open with Inducer On
3 Flashes
Pressure / Centrifugal Switch Closed with Inducer Off
2 Flashes
Control waiting
3 Flashes
HPS1 - Compressor Lock out
4 Flashes
Not Applicable
5 Flashes
LPS1 - Compressor Lock out
5 Flashes
Lock Out From Too Many Flame Losses
7 Flashes
FS1 - Compressor Lock out
6 Flashes
High Temperature Switch Open (Primary or Aux.)
Ignition Control Locked Out/
Ignition Control Failure / Limit Switch Trip / No
Jumper Plug in Heat Section
7 Flashes
Rollout Switch Open
9 Flashes
8 Flashes
Flame Present With Gas Off
9 Flashes
Gas Valve Stuck Off or On
10 Flashes
Flame Sense Circuit Failure
10 Flashes
Compressors Locked Out On Low
Outdoor Air Temperature1
11 Flashes
Compressors Locked Out Because The
Economizer Is Using Free Cooling1
13 Flashes
Compressor Held Off Due To Low Voltage1
14 Flashes
EEPROM Storage Failure (Control Failure)
OFF
No Power or Control Failure
1. These flash codes do not represent alarms.
Johnson Controls Unitary Products
63
Subject to change without notice. Printed in U.S.A.
Copyright © 2009 by Johnson Controls, Inc. All rights reserved.
Johnson Controls Unitary Products
5005 York Drive
Norman, OK 73069
362246-YIM-C-0109
Supersedes: 362246-YIM-B-0708