Akai PDP4294LV Operating instructions

IBN68-00711A-00esa
E
cover
2004.4.30
2:bl
PM
Page
3
PDP4294£V
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLEPARTSINSIDE. REFERSERVICING TO QUALIFIED SERVICEPERSONNEL.
This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact
with any inside part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been
included with this product.
Note to ¢A'rV system installer:
This reminder is provided to caJJCATV system instaJJer'sattention to Article 820-40 of the Nationai Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as practicak
Caution: FCCiCSA regulations state that any unauthorized changes or modifications to this equipment may
void the user's authority to operate it.
Caution:
To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.
Attention: pour eviter Jes chocs eiectriques, introduire Ja lame Jeplus large de Ja fiche dans Ja borne corre_
spondante de Ja prise et pousser jusqu'au fond.
Important:
One Federal Court has held that unauthorized recording of copyrighted TV programs is an
infringement of U.S. copyright laws.
Certain Canadian programs may also be copyrighted and any unauthorized recording in whole or in part
may be in violation of these rights.
1"0PREVENT
J)AMAGE
WHICHMAYRBULTJNFiREORELECTRJ(
SHO(J{HAZARD,J)ONO'[EXPOSE
THiS
APPUANCE
1"0RAiNORMOISTURE.
BN68-0071 IA-00esa_E
1 (walldel)
2004.4.30
2:52
PM
Page
T
Thank you for choosing ESA! Your new ESA product represents the latest in television technology.
We
designed it with easy-to-use on-screen menus and closed captioning capabilities, making it one of the
best products in its class. We are proud to offer you a product that will provide convenient, dependable service and enjoyment for years to come.
Always be careful when using your PDR To reduce the risk of fire, dectricai shock, and other injuries,
keep these safety precautions in mind when installing, using, and
maintaining your machine.
o Read all safety and operating instructions before operating your PDR
Keep the safety and operating instructions for future reference.
', Heed all warnings on the PDPand in the operating instructions.
Follow all operating and use instructions.
Unplug the PDP from the wall outlet before cleaning. Use a damp cloth; do not use liquid or aerosol
cleaners.
Never add any attachments and/or equipment without approval of the manufacturer. Such additions
can increase the risk of fire, electric shock, or other personal injury.
Do not use the PDPwhere contact with or immersion in water is a possibility, such as near bath tubs,
sinks, washing machines, swimming pods, etc.
Do not place the PDPon an unstable cart, stand, tripod, bracket,
table, or floor where it can faJk A falling PDP can cause serious injury
to a child or adult, and serious damage to the appliance. Use only
with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the PDP_Follow the manufacturer% instructions
when mounting the unit, and use a mounting accessory recommended
by the manufacturer. Move the PDP and cart with care. Quick stops,
excessive force, and uneven surfaces can make the unit and cart
unsteady and likely to overturn.
,, Provide ventilation for the PD£ The unit is designed with slots in the cabinet for ventilation to protect it
from overheating. Do not block these openings with any object, and do not place the PDPon a bed,
sofa, rug, or other similar surface_ Do not place it near a radiator or heat register. If you place the
PDP on a rack or bookcase, ensure that there is adequate ventilation and that you've followed the
manufacturer's instructions for mounting.
', Operate your PDPonly from the type of power source indicated on the marking Iabek If you are not
sure of the type of power supplied to your home, cons@ your appliance dealer or local power company.
Use only a grounded or polarized outJeL For your safety, this PDP is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet
only one way. if you are unable to insert the plug fully into the outlet, try reversing the plug.
if
the plug still does not fit, contact your electrician to replace your outlet.
3
Protect the power cord_ Power supply cords should be routed so that they won't be walked on or pinched
by objects placed on or against them_ Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.
Unplug the PDP from the wall outlet and disconnect the antenna or cable system during a lightning storm
or when left unattended and unused for long periods of time. This wiJJ prevent damage to the unit due to
lightning and power-line surges.
Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead
power lines or other electric light or power circuits or where it can fall into such power lines or circuits_
When installing an outside antenna system, be extremely careful to keep from touching the power lines
or circuits. Contact with such lines can be fatal.
Do not overload the wall outlet or extension cords. Overloading
can result in fire or electric shock.
Do not insert anything through the openings in the unit, where they can touch dangerous voltage points
or damage parts. Never spill liquid of any kind on the PDR
Ground outdoor antennas. If an outside antenna or cable system is connected to the PDP, be sure the
antenna or cable system is grounded so as to provide some protection against voltage surges and builtup static charges. Section 810 of the National Electrical Code, ANS[/NFPA NoJO-1984, provides information about proper grounding of the mast and supporting structure, grounding of the leaddn wire to an
antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
Do not attempt to service the PDPyourself. Refer all servicing to qualified service personnel. Unplug the
unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:
when the power-supply cord or plug is damaged
if liquid has been spilled on the unit or if objects have fallen into the unit
if the PDP has been exposed to rain or water
if the PDPdoes not operate normally by following the operating instructions
if the PDP has been dropped or the cabinet has been damaged
when the PDPexhibits a distinct change in performance
If you make adjustments yourself, adjust only those controls that are covered by the operating instructions_ Adjusting other controls may result in damage and will often require extensive work by a qualified
technician to restore the PDPto normak
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in additional damage to the unit.
Upon completion of any service or repairs to this PDP,ask the service technician to perform safety checks
to determine that the PDPis in a safe operating condition.
The PDPcan properly operate in a temperature range of 32~104°F(0~40°C1
Do not use in a hot and humid place.
and 80% humidity.
Before moving the PDP equipped with speakers, separate the speakers from the PDP.If you move the PDP
with the speakers attached, it may result in damage or injury.
4
BN68-0071 IA-00esa_E
1 (walldel)
2004.4.30
2:52
PM
Page
M
User instructions
Warning
The Federal Communications Commission Radio
Frequency Interference Statement includes the following warning:
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
c_rOtectionagainst harmful interference in a resientiai installation. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications. However, there is no guar_
antee that interference wiJJnot occur in a particular instaiJation.
User must use shielded signal interface cables to
maintain FCC compliance for the producL
Provided with this monitor is a detachable power
supply cord with IEC320 style terminations.
It may be suitable for connection to any UL Listed
personal computer with similar configuration.
Before making the connection, make sure the voltage rating of the computer convenience outlet is
the same as the monitor and that the ampere rating of the computer convenience outlet is equal to
or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed
detachable power cord with NEMA configuration
5_15P type (paraiiei blades) plug cap. For 240
Voit applications use only UL Listed Detachable
power supply cord with NEMA configuration
6015P type (tandem blades) plug cap.
If this equipment does cause harmful interference
to radio or television receptions, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
o Reorient or relocate the receiving antenna.
', Increase the separation between the equipment
and receiver.
', Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
', Consult the dealer or an experienced radio!TV
technician for help.
User Jnfermatien
Changes or modifications not expressly approved
by the part}, responsible for compliance could
void the user's authority to operate the equipment.
If necessary, consult your dealer or an experienced radio/television technician for additional
suggestions. You may find the booklet called How
to Identify and Resolve Radio/TV Interference
Problems heJpfuk This booklet was prepared by
the Federal Communications Commission. It is
available from the U.S. Government Printing
Office, Washington, DC 20402, Stock Number
004_000-00345-4.
I¢ Compliance
Notice
This Class B digital apparatus meets all require_
ments of the Canadian Interference_Causing
Equipment Regulations.
Notice de ¢onformit_
J¢
Cet appareii num@ique de ciasse B respecte
toutes Jesexigences du R&gJementsur Jes
6quipements produisant des interf6rences au
Canada.
VCCJ
This is a Class B product based on the standard
of the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI).
If this is used near a radio or television receiver
in a domestic environment, it may cause radio
interference. Install and use the equipment
according to the instruction manuak
This Class B digital apparatus complies with
Canadian fCES-O03.
Cet apparel! num6ique de la classe Best
conbrme d_la norme NMB-O03 du Canada.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 MicheJson Drive,
Suite #290, Irvine, CA92612 USA
This device complies with part 15 of the FCC Rules.Operation is subiect to the following two conditions:
(1/This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
unesired operation.
This television receiver provides display of television dosed captioning in accordance with
§ 15.119 of the FCC rules.
5
i
T
Wide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily
designed to view wide screen format full-motion video. The images displayed on them should primarily be
in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature, and
constantly moving_ Displaying stationary graphics and images on screen, such as the dark side-bars on
non-expanded standard format television video and programming, should be limited to no more than 5%
of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video game
displays,station Iogos, web sites or computer graphics and patterns, should be limited as described above
for all televisions. Displaying stationary
images that exceed the above guidelines
cart
_:ause uneven aging of PDP Displays that leave subtb, but permanent
burned-in
ghost images in the PDPpictureo
7"0avoid this, vary the programming
and images,
and primarily
display
fuH screen moving
images, not staJ'ionary pa_erns or dark bars°
On PDP models that offer picture sizing features, use these controls to view different formats as a fuji screen
picture.
Be careful in the selection and duration of television formats used for viewing_ Uneven PDPaging as a
result of format selection and use, as well as burned-in images, are not covered by your ESA limited
warranty.
@ Screen image retentbn
Do not display a still image (such as on a video game or when hooking up a PC to this PDP)on the plasma
display panel for more than,several minutes as it can cause screen image retentiom This image retention is
also known as screen burn . To avoid such image retention, refer to page 36 of this manual to reduce the
degree of brightness and contrast of this screen when displaying a still image.
Ddect
@ CeJJ
The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9
percent active cells, there may be some cells that do not produce light or remain lit.
@ Altitude
The PDP wiJJnot operate normally at altitudes above 6500 ft.
@ Warran|y
Warranty does not cover any damage caused by image retention.
BN68-00711A-00esa_E
l(walldel)
2004.4.30
2:52
PM
Page
7_
(hsssd (entrd
Gese[u[
_s£@[mati@s
Your New Plasma Display Panel ....................
10
Fine Tuning Channels ..................................
56
Remote Control Buttons ................................
12
LNA (Low Noise Amplifier)
57
..........................
(@nnectisga P( andO?eratien
Connecting VHF and UHF Antennas .............. 16
Connecting to a PC ....................................
60
Connecting Catole TV ..................................
17
Adjusting the PC Screen ..............................
64
Connecting Speakers ..................................
19
Changing the Position of the Image ................
65
Connecting a VCR ......................................
20
Changing the Size of the Image
66
Connecting a Camcorder
............................
21
Information
Connecting a DVD Hayer ............................
22
Picture Quality Adjustment
Connecting a DTV Receiver ..........................
23
..................
................................................
..........................
67
68
TimeSetting
Setting the Clock
Turning the PDPQn and Off
Memorizing
........................................
72
........................
26
Setting the Sleep Timer ................................
73
the Channels ............................
28
Setting the Timers ........................................
74
33
Setting the PreferredChannel and Volume Level .... 76
Setting Up Your Remote Control ....................
Picture(0strd
Fssdiss Descr@tien
Customizing the Picture
..............................
36
Selecting a Menu Language
........................
78
37
Viewing Closed Captions
............................
79
Sdecfirtg the Color Torte ..............................
38
Digital Noise Reduction
..............................
80
Viewing the Picture-in-Picture ........................
39
Setting Auto Power Off ................................
81
Changing the Screen Size
45
Using the V-Chip ..........................................
82
...................................
46
Selecting the Film Mode
88
Customizing the Sound ................................
48
Troubleshooting
Using Automatic Sound Settings ...................
49
Using Automatic Picture Settings
Freezing the Picture
..................
..........................
..............................
Sosn4(ostrd
Choosinga MuJti-ChanndSound(MTS}Soundtrack...... 50
Using the Auto Volume ................................
51
Using Dolby Virtual ......................................
52
Using a Subwoofer ......................................
53
..........................................
90
Care and Maintenance ................................
91
Specifications ..............................................
92
7
2004.4.30
IBN68-0071
iA-00esa
E 1 (walldel)
2 :52 PM
Page
8_
-/
/
\
_
_i_
BN68-00711A-00esa_E_l(walldel)
2004.4.30
2:52
PM
Page
9_
Your New Plasma Display Panel ....................................................
Remote Control Buttons ................................................................
10
12
Speakers
(optional)
RemeteCentral
Signal Receiver
Aim the remote
control towards
this spot on the PDR
SOURCE
button
Power Jndkat0r
Pressto display all of the available video sources
(ie., Video, S-Video, Component1, Component2, PC ).
Power Off
MENUbutton
: LED Red
Power On (Timer On) : LEDGreen
Power On (Timer Off) : LEDOff
Displays the main on-screen menu.
VOL(+,o)button
Press to increase or decrease the voJume_Also used
to select or adjust items on the on-screen menu.
Press CHA or CH_ to change ChanneJs_ Also
used to move up or down in the On-screen menu.
POWER
button
Press to turn the PDPon and off.
Fit the Stand-Base into the guide hole on the bottom of the monitor and tighten the left and
right sides using four screws for each side.
Two or more peple should carry the PDP.
Never lay the PDPon the floor because of possible damage
to the screen. Always store the PDP upright.
10
@
@
@
@ @
@ Service
jack
@ Cempenent
VideeiAudieinput jacks
(YiPb/P,/Audie LiAudieR)
For service only.
@ DVmmnput
jacks
Receives the digital video!audio
set top box or PC.
signals from a
@ ExternalSpeukerOutjacks
Connect external speakers.
@ PC(R6B)inputjacks(1Spin)
Connect to the video!audio
your PC.
Connect to the audio and component output
jacks of a DVD player or Set-Top Box.
output jacks on
@ Antennajack
Connect to antenna.
@S°VideeInputjacks
@ SuB°w0derspeaker0utputjack
Connect S_Videoiaudio signals from external
sources such VCRs or DVD players.
QVidee input jacks
Connect to the Sub-woofer speaker jack.
@ Pewerinput jack
Connect the supplied power cord.
Connect video/audio signals from external
sources such VCRs or DVD players.
Once you have unpacked your PDP,check to make sure that you have all the parts shown here.
If any piece is missing or broken, call your dealer.
RemoteContrd/AAA Batteries
Power Cord
Antenna Cable
FerriteCores(3EA)
Speaker Cables
Screw(4EA)
Stand-Base(2EA)
Owner's
instructions
11
Q Mute button
Press to mute the PDPsound.
@
0 PiP butten
Activates picture in picture.
@ Aspectbutton
Press to change the screen size.
@ RModebution
Adjust the PDP picture by selecting one of the preset
factory settings or select your personaJ, customized
picture settings.
@ S.Mo@butt0n
@
Adjust the PDP sound by selecting one of the preset
factory settings (or select your personal customized
sound settings.
@ Modebutt0n
Selects a target device to be controlled by the ESA
remote control (ie., VCR, CaNe, or DVD players).
@ Pre°(H ButJ0n
Tunes to the previous channel.
@ Sourcebutton
Press to display all of the available video sources
(ie., Video, s-Video, Component1, Component2, PC, DVI).
@ M/stick butt0n
Use it to move between options, select an option or
adjust the On-screen menu.
@ J)ispJaybutt0n
Press to display information on the PDPscreen.
@ Still J_uit0n
Press to pause the current screen.
@ MTSButt0n
Press to choose stereo, mono or Separate Audio
Program (SAP broadcast).
@ J)dby Virtual butt0n
12
This feature allows the TV's
speakers to provide a
Home Theater-like DoJby _
The center and surround
sounds are mixed into the LiR speakers.
@
@ Sleep butten
Press to select a _reset time interval for automatic
shutoff_
i@ CH°Scanbutton
Press to memorize (scan) the available channels.
@ CaptionButton
@
Controls the caption decoder.
@ PiP€@ntrdButtons
Source : Pressto select one of the available signal
sources for the HP window.
Swap
: Exchanges the video signal that is currently
displayed on the main screen with the signal
in the PIPwindow.
Locate : Pressto move the HP window on the screen.
S.Swap: Pressto select the audio (HP or Main).
Size
: Pressto make the PIPwindow Large, Small
or Double.
CHA,_ : Displays the available channels in sequence.
(These buttons change channels in the PIP
window only).
@ AutoProgram
Button
The TV automatically cycles through aJJof the available
channels and stores them in memory.
@ SETbuit0n
Used during setup of this remote control so that it will
work compatibly with other devices VCR, cane box,
DVD, etc.
@ Add/Erasebutt0n
Press to add or erase channels in the TV's memory.
@V(R, J)VJ)€0.tr0Jbutt0.s
Controls VCR tape or DVD disc functions: Stop, Rewind,
Play!Pause, Fast Forward.
Slide the back cover
to open the battery
compartment of the
remote control.
Install _/o AAA size batteries_Make sure to match
the "+" and "J' ends of the
batteries with the diagram
inside the compartment.
Slide the cover back into
place.
H
RemeteCentral Oper_tie_ R_ge°
You can use your remote control within a distance of 23 feet and an angle of 30 degrees
from the left and right sides of the remote control receiver of the PDR
13
2004.4.30
IBN68-0071
iA-00esa
E 2 (walldel)
2:55
PM
Page
\
_
_i_
BN68-00711A-00esa_E_2(walldel)
2004.4.30
2:55
PM
Page
Connecting VHF and UHF Antennas
..............................................
Connecting Cable TV....................................................................
16
17
Connecting Speakers ....................................................................
19
Connecting a VCR ........................................................................
20
Connecting a Camcorder ..............................................................
21
Connecting a DVD Player ..............................................................
22
Connecting a DTV Receiver ..........................................................
23
If your antenna looks like this:
it has 75-ohm round leads.
Hug
the Ant_"rma
antenna Cabe,
lead into
VHF/UHF
on the PDR
Ue te
anthe
acces
o/y _cterminal
uded
n the p_oduct packa te,
16
BN68-00711A-00esa_E2(walldel)
2004.4.30
2:55
PM
Page
You can connect different cable systems to your PDP, including cable without a cable box,
and cable with a cane box that descrambJes some or aJJchannds.
Hug the
the Anterlna
incoming Ca:>e,
cable on
intoaccess
the VHF/UHF
terminal on the PD£
Use
/y ncuded
n the p/oduct packo ]e,
1
Find the cable connected to the ANTENNA OUT terminal on your cable box. This terminal
might be labeled _ANT OUT _, _VHF OUT _, or simply _QUV.
Connect the cable to the VHF/UHF terminal on the PDP.
Ue the Anter_ o Cabe, an accesso/y nc ud_d
n the p/oduct pocka ]e,
17
To complete this connection you will need a _'o_way splitter, a RF (A/B} switch, and four coaxiai
cables (which you can buy from your ESA dealer or any electronics store).
1
Find and disconnect the cable that is connected to the ANTENNA IN terminal of
your cable box.
This terminal might be labeled "ANT iN",
"VHF IN", or simply, "IN". Connect this
cane to a two_way sphtter.
Cable
Splitter
Connect
a coaxial
PUT terminal
of the cable
splitterbetween
and the an
IN OUTterminal of the cable box.
Incoming
Cable
Splitter
Cable Box
Connect a coaxial
cane between
the box
ANTENNA
OUT terminal
of the cable
and the B-IN terminal of the AiB switch.
Incoming
Cable
Splitter
Cable Box
RF (A/B}
Switch
ANTENNAa coaxial
Connect
OUT terminal
cable between
of the cable
the box
and the B-IN terminal of the A/B switch.
Incoming
Cable
Splitter
Cable Box
RF (A/B)
Switch
Connect
the last
cable switch
between
OUT terminal
of coaxiai
the RF (A/B}
andthe
the VHF!UHF terminal on the PDP.
Incoming
Cable
Spl_tter
Cable
Box
After you've made this connection, set the A/B switch to the "A" position for normat viewing.
Set the A/B switch to the "B" position to view scrambled channels. (When you set the A/B switch
to "B", you win need to tune your Set-Top Box to the cable box's output channd, which is usuaiJy
channel 3 or 4.}
18
BN68-00711A-00esa_E2(walldel)
2004.4.30
2:55
PM
Page
External speakers are sold seperateJy. Check with your dealer.
PoweredSubwoofer
(Optionl
External speakers MUST have a power handling
capability of 10 watts minimum (impedance 8 ohml.
Connect the speaker audio cable to the external speaker output jack on the PDP matching the
"+" and "-" ends of the cable with the diagram on the PDff
Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws.
After removing the three screws on the PDP,clamp the speaker and the PDPtogether and
fasten the screws.
19
L C}iii
¸¸ :
y/
@
tO
O[
PDP
Power Plug
Audio Cable
S-Video CaMe
J
Video Cable
OF
J
Connect the Video/Audio
AUDIO!VIDEO
cables between the AUDIO(LiR)iVIDEO
jacks on the PDP and
OUT jacks on the VCR. (Note: For better video, you can usean S-Videocable.)
VideotapePJayback:
1_ Turn on your PDP,and press the SOURCE button on the remote control.
2. Move the joystick up or down to select "Video" or "S_Video", then press the joystick to enter.
3. Turn on your VCR, insert a videotape and press the play button.
The ferrite cores are used to attenuate undesired signals. When connecting the audio cable (PC,
DVI, S-Video, Video}, attach one of these ferrite cores to the cable near the connector.
When you connect the audio cable (PC, DVI, S-Video, Video} to the
connectors, bind the ferrite core around the cable to secure it.
20
BN68-0071 IA-00esa_E
2 (walldel)
2004.4.30
2:55
PM
Page
PDP
....
J
L
Power Plug
Video Cable
Audio Cable
Connect a Video!Audio
VIDEO!AUDIO
cable between the AUDIO(L/R)/VIDEQ
jacks on the PDPand the
OUTPUT jacks on the camcorder.
Viewing Tupes
1_ Turn on your PDP,and press the SOURCE button on the remote control.
2.
Move the joystick up or down to select the "Video", then press the joystick to enter.
3.
Turn on your camcorder and set it to Video Mode. (For details, refer to your camcorder
owner% instructions.)
4_ Set the IN/OUT
5.
switch on your camcorder to OUT.
Insert the tape into the camcorder and press the Play button.
21
This PDPdisplays the optimum picture in 720p mode.
PDP
DVD PJayer
Power Plug
Video Cable
Audio Cable
1 Connect a Video Cable between the Y, Pb, Pr (COMPONENT1,2)
and Y!PB!PRoutput jacks on the DVD players.
2
Connect a Audio Cable between the AUDIO L/R(CQMPONENT1,2)
and the AUDIO OUT jacks on the DVD player.
input jacks on the PDP
input jacks on the PDP
ToPJayDVD:
1_ Turn on your PDP,and press the SOURCE button on the remote controk
2.
Move the joystick up or down to select the "COMPONENT1
then press the joystick to enten
" or "COMPONENT2",
3. Turn on your DVD player, insert a DVD disc and press the Play buttom
For an explanation of Component video, see your DVD owner's instructions.
BN68-00711A-00esa_E2(walldel)
2004.4.30
2:55
PM
Page
This PDP displays the optimum picture in 720p mode.
DTV Receiver
PDP
Power
Plug
OF
Audio Cable
DVUCable
Use the DVI_Dconnection cable. (sold separately)
1 Connect the cable or antenna to the antenna input jack on the DTV.
2 Connect a Video cable between the Y, Pb, Pr (COMPONENT 1,2) or DVI jack on the PDP
and the Y, PB,PR(VIDEO OUTPUT JACKS) on the DTV receiver.
3 Connect an Audio cable between the COMPONENT
PDP and the AUDIO OUTPUT jacks on the DTV.
1,2 (LiR AUDIO) or DVI jacks on the
ToWatd {)'iV:
1. Turn on your PDP,and press the SOURCE button on the remote controk
2. Move the joystick up or down to select the "COMPONENT1
"DVF, then press the joystick to enter.
", "COMPONENT2"
or
3. Turn on your DTV receiver.
For an explanation of Component video, see your DTV receiver owner's instructions.
23
2004.4.30
IBN68-0071
iA-00esa
E 2 (walldel)
2:55
PM
Page
-/
/
\
_
_i_
BN68-00711A-00esa_E_2(walldel)
2004.4.30
2:55
PM
Page
Turning the PDP On and Off ..........................................................
26
Memorizing
28
the Channels ..............................................................
Setting Up Your Remote Control
....................................................
33
PDP
Off
Press the Power button on the remote controk
The PDPwiJJbe turned on and you wiJJbe ready to use it's
features_
You can also use the Power button on the front of the
PDR
Notes:
"
If your' PDP isn't turned on when the power button is
pressed: Press the MODE button to check if the TV mode
has been chosen (
}.
Your PDPhas a simple, easy-to-use menu system that appears on the PDPscreen. This system makes it con_
venient and fast to use features on the PDP.Your PDPalso Jetsyou display the status of many of your PDP's
features.
Viewing the Menus
With
power The
on, main
press menu
the Menu
button
remotethecontrol
appears
onon
thethe
screen.
The Picture menu is selected.
Mode
4
Custom
Adjust
Cobr Tone
4
Normal
Movo
Enter
i
Use the joystick (up, down} button to move items in the
menu. Use the joystick (left, right} button to display,
change, or use the selected items.
Use the joystick ( C_ ) button to enter items in the menu.
On screen menus disappear from the screen
automaticaJly after about thirty seconds, or you can
press the Menu button on your remote control to exit the
menu.
p.
Menu
DispJeyiegStatusJe[ermetiee
Press the Display button on the remote control. The PDP will
display the Picture mode, Sound mode, MTS, Signal and
Caption.
iI
Sound
MTS
Signal
Caption
i
Custom
: Mono
: Mono
: Off
27
BNb_-00
/llA-00esa
E
Z (wa±±de±)
2004.4.30
Z:bb
PM
Page
Your PDP can memorize and store all of the available channels for both "off-air" (antenna}
and cable channels. After the available channels are memorized, use the CH /", and CH v
buttons to scan through the channels. This eliminates the need to change channels by entering
the channel digits. There are three steps for memorizing channels: selecting a broadcast
source, memorizing the channels (automatic} and adding and deleting channels (manual}.
Before your television can begin memorizing the available channels, you must specify the type of
signal source that is connected to the PDP (i.e., an antenna or a cable system}.
Press the
Menu "Channel",
button. Move
thepress
joystick
up or
down
to select
then
the joystick
to enter.
Ant
Auto Program
Fine Tune
'_
O
LNA
,_
Off
1.
O,Scan
_}
2
Move the joystick left or right to select "Ant",
......
STD , "HRC" or IRC".
o If you are connected to an antenna, leave "Ant"
displayed, if you connected cable, move the
joystick left or right to the display the type of cable
system: "STD", "HRC", or "IRC".
(if you are not sure which type of cable system you
have, contact your cable company}.
; Move
:
Select
:
Menu
STD
Auto Program
Fine Tune
_
O
LNA
_
Off
_"
Ch Scan
!i_:i_£ii!i(ii_iii
¸
Move
Select
Menu
Press the Menu button to exit.
', STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company
to identify the type of cable system that exists in your particular area.
At this point the signal source has been selected. Proceed to "Storing Channels in Memory"
(next page}.
28
1
First, select the correct signal source (Ant, STD, HRC,
IRC}. See steps on previous page.
Press the Menu button. Move the joystick up or down to
select "Channel", then press the joystick to enter.
<
An_
Auto Program
Fine Tune
4
O
LNA
4
Off
P.
Ant / CAW
{
Ant
_"
Fine Tune
_
0
J,
LNA
4
Off
1,
Ch Scan
Move the joystick up or down to select "Auto Program",
then press the joystick to enter.
Ch Scan
.....
3
] Enter
i) Menu
The PDPwill begin memorizing all of the available
channels.
After all the available channels are stored, the
Auto program menu reappears. Move the joystick right
to exit.
"
; Move
Ant s0
Auto Program
: Stop
The PDP automatically cycles through all of the available channels and stores them in memory.
This takes about one to _'o minutes.
29
Use the added
numberorbuttons
wiJJbe
erased.to directly select the channel that
Ant4
Ex) Channel "4"
il
Press the Add/Erase
iii
Sleep
button:
Repeatedly pressing this button wiJJalternate between
"Added" and "Erased."
Ant4
Added
30
iiiiiiiiiiiiiiiiiii
Set
iiiiiiii: !:ii_}_i
_:i___iiii::i_
ili_ii_i
_I_
(PiP
m.
Press
Menu "Channel",
button. Move
thepress
joystick
or
down the
to select
then
the up
joystick
to enter.
An_
Auto Program
FMe "Tune
4
O
_"
LNA
_
Off
_"
Ch Scan
¢ Move
Movepress
the joystick
up ortodown
then
the joystick
enter.to select "Ch. Scan",
Only the memorized channels are chosen.
Move the joystick right to stop.
Ant / CATV
Select
4
[ Menu
Ant
Auto Program
Fine Tune
_
0
LNA
4
Oil
Cii
_'
S__n
: Stop
31
_4x
Press
theCHA or CHv buttons
tochange
channels.
When you press the CHA or CHv
buttons, the PDPchanges channels in sequence. You will see all the
channels that the PDPhas memorized. (The PDPmust have memorized at least three channels.)
You will not see channels that were either erased or not memorized.
ToView Memorized@annd
Pressthe CH.Scan button or the Channel button. Only the memorized channels are chosen.
Pressthe number buttons to go directly to a channel. For example, to select channel 27, press "2" then "7",
The TV wiJJchange channels when you press the second number.
When you usethe numberbuttons,you can directly selectchannelsthat were either erasedor not memorized, To
change to singledigit channels(0o_9)faster;press "0" bebre the singb digit, (Forchannel "4" press "0" then "4",
Pressthe Pre-CH button. The TV will switch to the fast channel viewed.
Toquickly switch between two channels that are far apart, tune to one channel, then use the number button
to select the second channel. Then, use the Pre-CH button to quickly alternate between them.
Pressthe VOL + or VOL - buttons to increase or decrease the volume.
At any time, you can temporarily cut off the sound using the Mute button.
Press
the Mute
button
the in
sound
cuts off.
The word
"Mute"
will and
appear
the Jower-ieft
corner of the screen.
To turn press
mute the
off, VOL
press+the
simply
or Mute
VOL -button
button.again, or
32
Muterq
BN68-00711A-00esa_E2(walldel)
2004.4.30
2:55
PM
Page
This PDP's remote control can operate almost any VCR, cable box, or DVD_ After it has been set up
properly, your remote control can operate in four different modes :TV, VCR, Cable, or DVD_
Pressing the corresponding button on the remote control allows you to switch be_/een these modes,
and control whichever piece of equipment you choose.
N> e: /_e ;<.,n'_
>t_:,co _,__,/real nor J e compa bb w _ha/J DVD P/a/e_s, V(_Rs,a _d Cable boxes
Setting Up the Re_ete te Operate YeurVCR, Cablebex, er DVD player
Turn off your VCR. (or Cable box, DVD player.}
Press the MODE button and make sure that the VCR
(or Cable box, DVD} LED is illuminated.
3
Press the Set button on your TV's remote control.
4
Using the number buttons on your remote control,
enter three digits of the VCR (or CaNe box, DVD)
code listed on page 34 of this manual for your
brand of VCR (or Cable box, DVD player). Make
sure you enter three digits of the code, even if the
first digit is a "0".
(If more than one code is listed, try the first one.}
VCR (i
',
Press the Power button on the remote control.
Your VCR (or Cable box, DVD player} should turn
on if your remote is set up correctly. If your VCR (or
Cable box, DVD player} does not turn on after set
up, repeat steps 2, 3, and 4, but try one of the other
codes listed for your brand of VCR (or Cable box,
DVD player}.
If no other codes are listed, try each code, 000
through 089 (or Cable box: 000 through 077,
DVD player: 000 through 008}.
Note_
o When your remote control is in "VCR" mode, the VCR control buttons (Stop, REW,
Play/Pause, FF} still operate your VCR.
,, When your remote control is in "CaMe box" or "DVD" mode, the VCR control buttons
(Stop, REW, Hay!Pause, FF} still operate your VCR.
33
BN68-00711A-00esaE2(walldel)
2004.4.30
2:55
PM
Page
3(_)
Re_oteControJ(odes
VCR Codes
A&mrai
Aiwa
Akai
00O.079
015
017,022,023,027,030
Audio Dynamics
014,016
Bell &rHowell
002
Broksonk
010
Candle
007,009,013,045.046,052
Cannon
008,053
Clnzen
007,009,013,045,046,052
Co[ortymu
014
Craig
007,012
Curtts-Mathes
000,007,008,014,
013,046,053,064,067
Daewoo
013,045,076
DBX
014,016
Dlmensla
000
KLH
LG
Lloyd
Loglk
LXI
073
009,01a, 046,060
015
031
015
Magnavox
Marantz
008,029,053,056
002,008,014,016,
029,030,046,061
009
008
008,009,012,015
027
032
005,035
003,027,035,040
Marta
MEI
Memorex
MGA
Midland
Minota
Mitsublsht
Montgomeryward
006
MTC
007,015
Mulutech
007,013,031,032
Emerson 008.009,010,013,
0J3,020,023,027, NFC 002,014,016,030.046.061,064
03404],042,047,049,057,062.065,067,0_8,070Opumus
006
Fisher 002, 0/2, 0/8,019,043,048,038
Panasonic
008,053,073,077
Funai
013
Pentax
005,035
Pentex Reserch+
046
GE
000,007,008,032,053
Go Video
007
Phflco
008,029,053,056
IqarmanKardon
014
Phflips
008,029
IfJtach_
005,015,035,036
PLoneer
005,016,033,050
Instanl Replay
008
Portland
044,045,052
ProScan
000
JC Penny
002,005,007,008,014,
Dynatech
F/ectrohome
015
027
0/6,030,035,051,053
JCI.
008,002,0/4,016,030,040
JVC
002,014,088,089
Kenwood
002,0/4,016,030,046
RCA
Samsung
Sansm
Sanyo
Scott
Sears
Sharp
Shmtom
Signature
Sony
Syh,ania
Symphonic
Tandy
Tash_ko
000,005,007,008,028,
035,037,054,069
007,013,022,032,042.077
016
002,012
013,041,049,068
002,005,009,012018,
019,035,043,048
006,027,039.045
017,026, 03!, 055
015
017,026,038
008,015,029,053,056
015
002,015
009
Tatung
030
Teac
015.030,069
Te(hnlcs
008
Termka
008,009,015,021
TMK
067
Toshiba
003,013,019.048.049
Totevls/on
007,009
UnJ/ech
007
Vector Research
014,016
Vtctor
016
Vtdeo Concepts
Valeosomc
Quartz
002
Quasar
008,053
Radio Shack/Reahst
002,006,008,
009,0/2,015,019,027,045,053
Wards
NSC
Oak
Osk Sigma
Panasomc
Signature
Spmcer
Starcom
Yamaha
Zemlh
014, 0/0
007
005,006,007,008,009,
0/2,013, 0/5,027,031,035
002, 0/4, 0/0, 030, 040
O/l, 0/7,020,079
Cable Box Codes
Anwsion
Cablestar
Eagle
Eastern Int
General Instrumem
007, 008
007, 008
007,008
002
046
GI
004, 005,015,023,024,
025,030,036,067,068,069
Itamhn
003,012,013,034,048
Ihta{ht
037,043,046
JerroM
004,005,015,023,024,
025,030, 036,046,002,063
Macom
037,043
Magnavox
007, 008,019, 02l,
026, 028,029,032,033,040,041
DVD Codes
34
Phfllps
Proscan
RCA
Toshiba
Panasona
001
002
002
003
004
Sony
Samsung
008
000
009
010, 038
016
003,027, 039, 061,
073,074
Phthps
007. 008,019,021,026,
028,029,032,033,
040, 041
Pioneer
018,020,044, 074, 077
Randtek
007,008
RCA
000, 027,066
Regal
003, 012,013
Regency
002,033
SA
070, 071,072
Samsung
044,003,022, 063,064
040
027
046
Stargate 2000
058
Sylvama
011,059
Texscan
011,059
Tocom 017,021,049,050,055,073
Unika
031,032, 0dl
Umversal
051,052
Vmwster
007,008,019,021,026,
028,029, 032,033,040,041
Warner Amex
044
Zemth
014, 042,057,001,
075,076
BN68-00711A-00esa_E_2(walldel)
2004.4.30
2:55
PM
Page
3_
Customizing the Picture ................................................................
36
Using Automatic Picture Settings ....................................................
37
Selecting the Color Tone................................................................
38
Viewing the Picture-in-Picture ..........................................................
39
Changing the Screen Size ............................................................
45
Freezing the Picture ......................................................................
46
You can use the omscreen menus to change the Contrast, Brightness, Sharpness, Color,
and Tint settings of your PDP.
Press the Menu button, then press the joystick to
enter.
Custom
Ad}us_
Color Tone
Move
Move the joystick up or down to select "Adjust",
then press the joystick to enter.
You wiJJalso see the items "Contrast", "Brightness",
"Sharpness", "Color" and "Tint".
4
Select
Menu
4
Normal
Brightness
_
50
Sharpness
Color
_
_
50
50
80
s
Tint
Move
the
item.
the joystick left or right to change the value of
Press the Menu button to exit.
', In the PCiDVI mode, you can't adjust the "Sharpness", "Color" and "Tint".
36
J'
Color Tone
Movetothe
joystick up or down to select the item you
wish
change.
', The Tint cannot be adjusted in Component(480p,
Custom
720p, 1080i} mode.
R 50 _
(: }
Your PDPhas automatic picture settings that allow you to adjust the video display easily.
Press the Menu button, then press the joystick to
enter.
Custom
Adjust
ColorTone
Move the joystick left or right to select "Custom",
"Dynamic", "Standard" or "Movie" picture setting.
', You can select "High", "Middie", "Low" or
"Custom" in PC!DVI mode.
_
Custom
I,
Dynamic
X
Adjust
ColorTone
I
Custom
I,
:s
Move
3
Select
Menu
Press the Menu button to exit.
37
Press the Menu button, then press the joystick to
enter.
Ad}ust
Color Tone
....M.....
Move the joystick up or down to select "Color
Tone", then move the joystick left or right to select
"Normal', "Warm1 ", "Warm2", "Cool2" or
"Cool1 "
o You can select "Custom", "Color1 ", "Color2" or
"Color3" in PC mode.
o You can select "Cdorl ", "Cdor2" or "Color3" in
DV[ mode.
Press the Menu button to exit.
38
Mode
Select
_
Menu
Custom
Adjust
Normal[]]
_,
BN68-00711A-00esa_E2(walldel)
2004.4.30
2:55
PM
Page
Press the
Menu "PIP",
button.then
Move
thethe
joystick
up to
or
down
to select
press
joystick
enter.
Off
b_q_ i
i
_s
Select
:si Menu
Move the joystick left or right to select "On".
The PIP image wiJJappear in the corner of the
screen.
3
Press the Menu button to exit.
0 : HP and Swap Operate
X : HP doesn't Operate
PiPSettings
X
....
o
o
o
x
x
x
x
0
0
0
X
X
X
X
0
0
0
X
X
X
X
39
You can use PIPto view a signal from an externai source, such as a VCR.
Press the
Menu "PIP",
button.then
Move
thethe
joystick
up to
or
down
to select
press
joystick
enter.
_
On
TV
Size
4
Large
Locate
_
_
Select
4
On
_"
{
Large
_"
Source
_-
Swap
Move the joystick up or down to select "Source".
Swap
Size
3
Tv
Move the joystick left or right to cycle through
all of the avaiiabie signai sources:
"TV", "Video", "S_Video", "Component 1",
"Component 2", "PC" and "DVF.
The signal from these inputs wiJJnot appear if you
have not connected any equipment to the PDP's
respective input.
Press the Menu button to exit.
Note
PIPfunction operates in Wide screen.
', Using Multi-Screen in the Normat, Zoom 1 or Zoom2 screen wiJJchange the size of the main screen
to Wide screen.
40
PiP
Press the
Menu "PIP",
buttomthen
Move
thethe
joystick
up to
or
down
to select
press
joystick
enter.
Source
_
TV
Size
_i
Large
Select
'_
On
Source
4
TV
Size
_
Large
_
Loca_e
4
_J=
I_
Swap
Move the joystick up or down to select "Swap",
then press the joystick to enter.
The image in the HP window will appear on the
main screen, and vice versa.
3
_'
Press the Menu button to exit.
&Swap
Press the &Swap button to switch between the Main or Sub
(HP} audio source.
Source
Locate
41
Size
Press the Menu button. Move the joystick up or
down to se ecr r_ , then press the joystick to
enter.
Move the joystick up or down to sdect
S'ze'.
Select
_
On
Source
_
TV
Swap
Loca_e
Ant/C/XTV
Channel
S MOVe
Move the joystick Jdt or right to select "Small",
"Double" or "Large".
Press the Menu button to exit.
42
_'
iiiiiiii: !:ii_}_i
_LI
__ijii::i_
ili_ii_i
_I_
PiP
÷
Press the Menu button. Move the joystick up or
down to seJect "PIP", then press the joystick to
enter.
Source
_
TV
Size
_i
Large
Locate
,I
,M,o, v
.........................
:_3Menu
Move the joystick up or down to seJect "Locate".
_i}7
Move
where the
you joystick
want. Jeffor right to move the PIPscreen
/
Swap
Size
_
Large
Press the Menu button to exit.
43
Press the Menu button. Move the joystick up or
down to se ecr. tJnlp_
r_ , then press the joystick to
enter.
/
4
(
On
*_
Large
F
Source
swap
size
Locate
Ant/CAl"V
Channel
$ lv_ove
Move the joystick up or down to select "Ant/CATV".
Move the joystick, left or right to select "Ant", "STD",
"HRC" or "IRC".
Select
_
On
Source
_
TV
Swap
Size
4
Large
Locat_
c, '
'_
,_..................
'
Channel
Move
J'
>
STD 5
_ Selectj
_FMenu
L,-
3
Move the joystick up or down to select "Channel'.
Move the joystick left or right to change the channel
that appears in the PIPwindow_ You can also press
PIPCHA, T buttons on the remote control
:_
Select
Source
S'aap
Size
Locate
AnUCATV
Mov_
Press the Menu Button to exit.
44
On
Large
_"
_ii
I
BN68-00711A-00esa_E2(walldel)
2004.4.30
2:55
PM
Page
When you press the Aspect button on the remote control, the PDP's screen mode should appear in
sequence. The screen displays in this order: Wide, Panorama, Zoom1, Zoom2, Normal.
', If you watch a still image or the Normal (4:3) mode for a long time (over 2 hours), an image may
be burned onto the screen. View the monitor in Wide or Panorama mode as much as possible.
Wide
Sets the picture to 16:9 wide mode.
The screen size when the Zoom 1 screen is
vertically enlarged.
ooo
c::>O
Nermd(4:3)
Converts regular 4:3 aspect ratio screen to
wide screen.
Q
Zoom
Setsthepicture
to4:3 normaJmode
0
'J
The screen size when Wide screen is vertically
enlarged.
Q C)Q
o In TV, VIDEO, S_VIDEO and Component(480i) modes, all screen modes can be selected.
(Wide _ Panorama _ Zoom1 _ Zoom2 _ Normai).
', In PCiDVI mode, only Wide & Normal modes can be selected.
', In Component(480p,
720p.
10800 modes, Panorama mode can't be selected.
In Component(480p, 720p. 1080i} modes, you can move the picture on screen by pressing
the UpA or Downy button. (AJJscreen modes)
Changing the screen size to Normal, Zoom1 or Zoom2 during PIP mode will cause the PIP
window to disappear.
45
BN68-00711A-00esaE2(walldel)
2004.4.30
2:55
PM
Page
4_>
StiJJ
Press the Still huron on rne emote control ro Freeze a
moving olcrure. Press again to cancel.
[_
_PModeS.Mode
_
DdbyVirtua
_/_;_So
/
46
BN68-00711A-00esa_E_2(walldel)
2004.4.30
2:55
PM
Page
Customizing the Sound ................................................................
48
Using Automatic Sound Settings ....................................................
49
Choosing a Multi-Channe! Sound (MTS)Soundtrack ..........................
50
Using the Auto Volume ..................................................................
51
Using Dolby Virtual ......................................................................
52
Using a Subwaofer ......................................................................
53
Press the
Menu "Sound",
button. Move
joystick
up or
down
to select
then the
press
the joystick
to enter.
Mode
MTS
Custom
I.
Mono
_,
Auto Volume
_
Off
_"
Dolby Vfftual
Woofer
_
Off
_"
# Move
Move the joystick up or down to select "Adjust",
then press the joystick to enter.
You wiJJalso see the items "Bass", "Treble" and
"Balance".
_
Adjust
Mode
_
_ Select
{
_ Menu
Custom
J,
Adjust
MTS
Mono
I,
Auto V_lume
4
_t
Off
I,
Dolby Virlu_l
_
Off
_"
Woofer
Move tothe
joystick up or down to select the item you
wish
change.
Bass
_
Treble
_
50
L 50 _
R 50
Balance
50
Move
the
item.
the joystick left or right to change the value of
ii! [Bass
Press the Menu button to exit.
48
821/:
Press the
Menu "Sound",
button. Move
joystick
up or
down
to seJect
then the
press
the joystick
to enter.
Mode
_1
MTS
'I
Auto Valume
4
Custom
_,
Mona
I.
Off
I,
Music
I,
Mona
_"
Woofer
Move the joystick Jeftor right to seJect "Custom",
"Standard", "Music", "Movie" or "Speech" sound
setting.
3
Mode
Adjust
MTS
_1
_
Auto Volume
{
Off
Dolby VMual
Woofer
4!
Off
_"
Press the Menu button to exit.
49
Depending on the particular program being broadcast, you can listen to stereo, mono,
or a Separate Audio Program. (SAP audio is usually a foreign-language translation.
Sometimes SAP has unrelated information like news or weather.)
Press the
Menu "Sound",
button. Move
joystick
up or
down
to select
then the
press
the joystick
to enter.
Move the joystick up or down to select "MTS".
Mode
I
Standard
I,
Mone
I.
Adjust
MTS
'q
Auto Volume
_1
Off
m
Move theorjoystick
"Stereo"
"SAP".left or right to select "Mona",
Mode
Adjust
_
MTS
,I
Standard
Stereo
I,
I,
Auto Volume
_
Off
1"
Dolby
_
Off
I,
Vidual
Woofer
Press the Menu button to exit.
o
Choose Stereo for channels that are broadcasting in stereo.
_,
Choose Meno for channels that are broadcasting in mono, or if you are having difficulty receiving
a stereo signal
Choose SAP to listen to the Separate Audio Program, which is usually a foreign-language translation.
Note
_MTS
50
function operates in TV mode onIy.
BN68-00711A-00esa_E2(walldel)
2004.4.30
2:55
PM
Page
Each broadcasting station has its own signal conditions, which can make it necessary to
adjust the volume every time the channel is changed. "Auto volume" Jetsyou automatically
adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.
Press the
Menu "Sound",
button. Move
joystick
up or
down
to select
then the
press
the joystick
to enter.
Mode
4
Adjust
MTS
'4
Custom
_-
Mono
_'
Auto Volume
4
Off
_'
Dolby Vidual
_1
Off
Woofer
Move the joystick up or down to select "Auto
Volume".
ix l
ii
Mode
4
Adjust
MTS
{
Standard
_.
Mono
_,
Auto Volume
_
Off
I,
Dolby Vidual
_
Off
_"
Woofer
i
3
# Move
4_Select
_ Menu
T_T
Move the joystick right to select "On".
Mode
_1 Standard
Adjust
MTS
4
I,
Mono
Auto Volume
_
On
Dolby Vidual
Woofer
41
Off
_"
Press the Menu button to exit.
51
This feature alJows the PDP's optional L/R speakers to provide a Home Theater-Jike DoJby
effect. The center and surround sounds are mixed into the L/R speakers.
Press the Menu button. Move the ioystick up or
down to select "Sound", then Fess the ioystick
to enter.
Move the ioystick up or down to seJect "DoJby
Virtua{".
Mode
4
Standard
Adjust
MTS
,_
Mono
I_
Auto Volume
_
Off
b"
DOIby Vidual
'_
Off
_"
Woofer
3
Move the joystick left or right to select "On".
"::/!ili¸¸ii
Mode
_
MTS
Auto
Slandard
_
Volume
DoIby Virtual
_'
Press the Menu button to exit.
52
::
Mono
'_
Off
_
:
4
On
I,
:
Woofer
,,€Move
i:
o Select
_ Menu
:
BN68-00711A-00esa_E2(walldel)
2004.4.30
2:55
PM
Page
5_
Press the
Menu "Sound",
button. Move
joystick
up or
down
to select
then the
press
the joystick
to enter.
Mode
_1
Custom
I,
Mono
I.
Off
I,
Adjust
MTS
'q
Auto Volume
4
#_lw
Vid0al _ off
Woofer
Move the joystick up or down to select "Woofer",
then press the joystick to enter.
Mode
4
Adjust
M'[S
_
Standard
Mono
_'
Auto Volume
_
Off
Dolby Vidual
<
Off
Woofer
::
# Move
_ Enter
_ Menu
Move the joystick left or right to seiect "On".
Woofer
Volume
_1
Cutoff Freq
:?
Move
the joystick
up orleft
down
to select
"Volume",
then move
the joystick
or right
to adjust
the
value of the item.
This sets the volume for the subwoofer.
I
-t-Move
Move the joystick up or down to select "Cutoff
Freq.", then move the joystick left or right to adjust
the value of the item.
This sets the cutoff frequency for the subwoofer.
For example, if you set the cutoff frequency at
130Hz, the subwoofer wiJJreproduce frequencies
of 130Hz and lower.
120Hz
_ Select
{
_"
_ Menu
On
_,
_
Cutoff Freq
_M .....
_,
50
<
Woofer
V0Jume
On
_
50
_
120Hz
Adjust
_"
_Menu
_ff
Woofer
Volume
Cut0ff Freq
-t-Move
4
On
_,
4
130Hz
_
50
l_Adjust
_Menu
Press the Menu button to exit.
53
BN68-00711A-00esa_E_3(walldel)
2004.4.30
3:7 PM
Page
54_
-/
/
\
_
_i_
BN68-00711A-00esa_E_3(walldel)
2004.4.30
3:7 PM
ii!
¸¸¸¸¸¸
iill ;i
Page
!
55_
;!!i
ilk
i!!iiili
¸¸
Fine Tuning Channels ....................................................................
56
LNA (Low Noise Amplifier) ............................................................
57
BNb_-00/IIA-00esa
E
3(walldel)
2004.4.30
3: / PM
Page
b_
Use fine tuning to manuaJJy adjust a particuJar channeJ for optimaJ reception.
Press
Menu "ChanneJ",
button. Move
thepress
joystick
or
down the
to seJect
then
the up
joystick
to
enter.
Move
2
Select
Menu
Move the joystick up or down to seiect "Fine Tune".
Ant / C/_TV
4
Ant
_
Off
_
Ant
_
Off
_*
Auto Program
LNA
Ch Scan
Move the joystick Jeftor right to adjust the fine
tuning.
Ant / CATV
Auto Program
LNA
To
store
fine tuning
in the TV's memory,
move
thethe
joystick
up. (Asetting
star icon<*>wiJJ
appear.}
To reset the fine tuning to "0", move the joystick
down.
Press the Menu button to exit.
56
I•
BN68-00711A-00esa_E3(walldel)
2004.4.30
3:7
PM
Page
5:
if the TV is operating in a weak-signal area, sometimes the LNA function can improve
the reception (a low-noise preamplifier boosts the incoming signal).
Press
Menu "Channel",
button. Move
thepress
joystick
or
down the
to select
then
the up
joystick
to
enter.
Move the joystick up or down to select "LNA".
Ant / C_TV
_
Ant
_
0
Off
Ant / CATV
_
An_
Auto Program
FineTune
_
Auto Program
FineTune
Ch Scan
Move
the the
joystick
left or
to select
LNA "On."
',Moving
joystick
Jeffright
or right
wiJJalternate
between "On" and "Off."
0
On
Oh Scan
Move
Select
Menu
Press the Menu button to exit.
57
BN68-00711A-00esa_E_3(walldel)
2004.4.30
3:7 PM
Page
58_
-/
/
\
_
_i_
BN68-00711A-00esa_E_3(walldel)
2004.4.30
P
3:7 PM
L A
S
Page
59_
M
A
D
I
S
P
L A
Y
P
A
N
E
L
Connecting to a PC ......................................................................
60
Adiusting the PC Screen ................................................................
64
Changing the Position of the image ................................................
65
Changing the Size of the Image ....................................................
information ..................................................................................
66
67
Picture Quality Adjustment ............................................................
68
Connection to a Macintosh PC may require an adaptor that fits the PC terminal.
PDP
iii
ii_
_iiii
®iii
_iii
Power Plug
Use the DVI-D
connection cable_
(sold separately}
DVI CaMe
PC CaNe
Audio Cable
DVIiack
(Theactualconfigurationon your PC
may be different,
dependingon the
rnodek)
pc
_
_ _
1 Connect a PC (15pin} cable between the Video Output jack (or DVI jack} on the PC and the
RGB IN (or DVI IN} Input jack (15p D-SUB} on the PDP.
2 Connect a Audio cable be_'een the Audio (RGB or DVI} on the PC and the Audio LiR (RGB
or DVI} input jacks on the PDP.
Tow_td_ the PCs_ree_:
1. Turn on your PDP,and press the Source button on the remote control.
2_ Move the joystick up or down to select "PC", then press the joystick to enter.
3.
Turn on PC and check for PC system requirements. (Refer to pages 62 and 63
for PC system requirements.}
3. Adjust the PC screen. (Refer to pages 64 and 70.}
60
Pin
DoSubCable
DVFD CaBle (Digital-Only
Cennecter)
o 15Pin Signal Cable (based on protruded pin}
PC!UT
PinNo
PC IN
]
Red (R)
Red (R)
1
T,M,D,S,
Data2=
13
T.M.D,S,
2
Green(O)
Green (G)
2
T.M.D.S.
Data2+
14
+SV Power
Pin No
Signal
Assignment
Signal
Assignment
Data3+
3
BUue(B)
BUue(B}
3
T.M.D.S.
Data2/4
15
Ground
4
5
Grounding
Grounding(DDC)
Grounding
4
T.M.D.S.
Data4=
16
Hot Plug Detect
5
T.M.D.S.
Data4+
17
%M.D.S.
Data0_
6
Bed (R)Grounding
Red (R) Grounding
6
DDC
18
T.M.D.S.
Data0+
7
8
9
Green{G) Grounding
Blue (B}Grounding
Reserved
Green (G) Grounding
7
DDC Data
19
T.M.D.S.
Data0/5
8
No Connect
20
T.M.D.S.
DataS=
9
T.M.D.S.
Data1=
21
T.M.D.S.
Data5+
l0
Sync Grounding
Syne Grounding
10
T.M.D.S.
Data1+
22
%M.D.S.
Cloak ShieUd
iI
Grounding
Grounding
11
T.M.D.S.
Data1/3
23
T.M.D.S.
Clock+
12
13
Data (DDC}
HodzontaU
sync,
Data (DDC)
12
T.M.D.S.
Data3=
24
T.M.D.S.
Clock=
Horizontal sync.
14
Verticalsync.
Vertical sync.
i5
Clock (DDC)
Clack (DDC)
gup
Grounding
{DDC)
Blue (B) Grounding
Reserved
Shield
Pin No
Clock
Shield
(for +5V)
Shield
PDP(
Our adoption of the new VESA® Plug and Play solution eliminates complicated and time consuming
setup. It aiiows you to install your monitor in a Plug and Play compatible system, without the usual
setup hassles and confusion. Your PC system can easily identify and configure itself for use with your
display. This monitor automatically tells the PC system its Extended Display Identification data (EDID}
using Display Data Channel (DDC} protocols.
61
to upYour
PC
i}
The Windows display-settings for a b,picai computer are shown below. However, the actual screens
on your PC will probably be different, depending upon your particular version of Windows and your
particular video car& But even if your actual screens look different, the same, basic set-up information
wiJJapply in almost oil cases. (If not, contact your computer manufacturer or ESA DeaJen)
On the windows screen, select in the following
sequence : Start _ Settings _ Control Panek
_coessib@
Option
Date/1
U_e
the Se_dng_
ConU'ol
Psnel
pel _on_F
compute
Select
an
_ae
Display
Add Ne_
Hald_ale
Find
Fas_
Add/R emov_ Adobe Gar_p_
PFo_r_s
Fonts
fn
When the control panel screen appears,
double-click on "Display" and a display
dialog-box vviJJappear.
Gaffe
Co
tTollel
to
ze ,_ouz
tern
to view
it
HP Jet&df_,in
In_eme_
Keyboald
LiveUpdate
Nail
_*d F_
Ne_wolk
Pa
s$_qrU
description
_'4_!:9s 3 t
_: r,-,
Node
r_
Noue
tduRi{_dia
Select the "Settings" tab inthe display diaiogbox.
The _'o key variables that apply to the PDP-PC
interface are "resolution" and "colors".
The correct settings for these two variables are:
', Size (sometimes called "resolution"):
640 x 480 pixeis.
', Color: "24-bit" color (might also be expressed as "16 million cdors'}Shown at left is
a typical screen for "Display" dialog box.
If a vertical-frequency option exists on your
display settings dialog box, the correct value is
"60" or "60 Hz." Otherwise, just click "OK"
and exit the dialog box.
Continued._
62
Notes_
Both screen position and size will vary, depending on the type of PC monitor and its resolution.
The table below shows aJJof the display modes that are supported:
Vertical
Horizontal
Vertical
Horizontal
Frequency(Hz}
Frequency(KHz}
polarity
polarity
70.086
31.469
N
P
85.080
37.861
N
P
640 X 400
85.080
37.861
P
N
720 X 400
70.087
31.469
P
N
85.039
37.927
P
N
59.940
31.469
N
N
72.809
37.861
N
N
BM PC/ AT
75.000
37.500
N
N
Compatible
85.008
43.269
N
N
56.250
35.156
N/P
NiP
60.317
37.879
P
P
72.188
48.077
P
P
75.000
46.875
P
P
85.061
53.674
P
P
60.004
48.363
N
N
70.069
56.476
N
N
75.029
60.023
P
P
84.997
68.677
P
P
Video signal
Dot X Line
640 X 350
640 X 480
800 X 600
1024 X 768
(N: Negative / P: Positive)
"
The interlace mode is not supported.
o The PDPoperates abnormally if a non-standard video format is selected.
Notes:
When this PDP is used as a PC display, 32-bit color is supported.
Depending on the manufacturer, your PC display screen might appear different.
(and depending on your particular version of Windows).
Check your PC instruction book for information about connecting your PC to a PDP.
If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical} and 31 .SkHZ
(horizontal}.
In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power
is turned off (or if the PC is disconnected). If so, press the Source button to enter the VIDEO mode.
Also, make sure that the PC is connected.
', Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise,
random signals might appear).
63
P_ese):
*
Press the Source button, then move the ioystick up or down to select PC. Press the ioysfick to select PC mode
:7:
7:
Press the Menu button, then press the joystick to
enter.
Custom
Adjus_
Cobr
Tone
I
Custom
Color Adius_
Move the joystick up or down to select "Color
Tone", then move the joystick left or right to select
"Custom". When "Custom" is selected, the word
"Color Adjust" wiJJappear on the screen.
Mode
J_
s@
Custom
Adius_
Custom
Color Adiusi
Move
Move
joystick
or joystick
down toto select
Adjust",thethen
pressupthe
enter. "Color
Mode
Select
Ad_ost
_
Menu
Custom
colorT,, ne
Cos om
,
Move
4
Move the joystick up or down to select the item you
want to change, then move the joystick right or left
to change the value of the item, using the on-screen
gauge as your guide.
64
Menu
Green
50
Blue
5O
Move
Press the Menu button to exit.
Enter
Adjust
Menu
BN68-00711A-00esa_E3(walldel)
2004.4.30
3:7
PM
Page
65_
P[eset:
® Press
theSourcebuffon,
thenmove theioysfick
up ordown toselect
PC Press
theioystick
toselect
PC mode
Press
Menu "PC",
button.then
Move
thethe
joystick
up to
or enter.
down the
to select
press
joystick
f
Adjust
Scaling
4
Wide
Informatbn
Auto Adjust
Move
]Enter
:Menu
Press the joystick to enter, then adjust the screen
position by using the joystick button.
Down
Press the Menu button to exit.
65
P£eset:
•
Pressthe Source button, then move the ioystick up or down to select PC. Pressthe ioystick to select PC mode
Press the
Menu "PC",
button.then
Move
thethe
joystick
up to
or enter.
down
to select
press
joystick
Move the joystick up or down to select "Scaling".
::Move
Select
Menu
Move the joystick left or right to select "Wide"
or "Normal".
Position
Adjust
Normal
Information
Auto Adjust
....
Press the Menu button to exit.
66
Select
Menu
P_eset_
Pressthe Source button, then move the ioystick up or down to selectPC. Pressthe ioystick to selectPC mode.
Press
Menu "PC",
button.then
Move
thethe
joystick
up to
or enter.
down the
to select
press
joystick
Adjus_
Scaling
_nformation
4
Wide
_"
Au_o
Adius_
Move
Move the joystick up or down to select 'qnformation", then press the joystick to enter.
The vertical, horizontal frequencies and resolution
appear.
Enter
_::Menu
Position
Adiusi
Scaling
.t_2
_
Wide
_,
AoAd
o os
: Move
Enter
Menu
Resolution
:
1024 * 768
HFrequency
:
4852 KHz
V-Frequency
:
6036
Hz
Menu
Press the Menu button to exit.
67
BNb_-00/llA-00esaE&(wa±±de±)
2004.4.30
&:/
PM
Page
65Q
i
Preset"
*
Press the Source button, then move the ioystick up or down to select PC. Press the ioysfick to select PC mode
Press the
Menu "PC",
button.then
Move
thethe
joystick
up to
or enter.
down
to seiect
press
joystick
Move the joystick up or down to select "Auto
Adjust", then move the joystick left or right to enter.
Position
Adjust
Scaling
4
Wide
information
iiiiiiJl;JiJ!!iii!!i
Move
:Enter
The
Adjust" appears
on the screen
and message
the picture"Auto
adjustments
are automatically
activated.
Auto Adjust
Press the Menu button to exit.
68
:Menu
P_ese_:
*
Press the Source button, then move the ioystick up or down to select PC. Press the ioystick to select PC mode
7
Press
Menu "PC",
button,then
move
the the
joystick
up to
or enter.
down the
to seiect
press
joystick
Adjust
Scaling
I
Wide
Information
Move the joystick up or down to select "Adjust",
then move the joystick left or right to enter.
Position
k st
Scaling
Information
Wide
Auto Adiust
3
Move the joystick up or down to select "Coarse".
Remove picture noise (vertical stripes} on the screen
by moving the joystick left or right. (If Coarse is
not set properly, vertical stripes win appear on the
screen.)
Move the Menu button to exit.
69
P_ese_:
*
Press the Source button, then move the joystick up or down to select PC Press the joystick to select PC mode
k ¸¸
Press the
Menu "PC",
button.then
Move
thethe
joystick
upto
orenter.
down
to select
press
joystick
Adjust
Scaling
I
Wide
I,
Information
Move the joystick up or down to select "Adjust",
then move the joystick left or right to enter.
Move
3
Move the joystick up or down to select "Fine".
Remove picture noise (vertical stripes} on the screen
by moving the joystick left or right. (If Fine is
not set properly, vertical stripes wiJJappear on the
screen.}
Move the Menu button to exit.
7O
Enter
2 Menu
BN68-00711A-00esaE4(walldel)
2004.4.30
3:8 PM
Page
7
iiii!
!!i!i!
!!i_!iiii_i!i!_ii!i_i_!!i!iiieii!ii!_ii!_ii_i!
ii
_¸¸'_¸¸
iii !i!!i
i!!il
!i!i!i!
!i!!i i!iiiiii!ilil
iil
_¸¸_¸¸
i!k ii!i_
il¸¸
Setting the Clock .......................................................................
72
Setting the Sleep Timer ...............................................................
73
Setting the Timers ......................................................................
74
Setting the Preferred Channel and Volume Level ............................
76
BNb_-00/IIA-00esa
E
4(wa±±de±)
2004.4.50
3:_
PM
Page
/2_
o
Press the
Menu "Function",
button. Move
thepress
joystick
or
down
to select
then
the up
joystick
to enter.
English
Time
Caption
NR
_
Off
Auto Power Off
_
Off
_
Off
I,
V-Chip
Film Mode
Move
Sebct
I,
; Menu
Move the joystick up or down to select "Time", then
press the joystick to enter.
Language
4
English
_'
Caption
NR
_
Off
Auto Power Off
_1
Off
_'
vChip
Move the
the joystick
joystick up
left or
or down
right to
then
move
to select
select hour,
the correct
hour.
10 :
- am
-:--
am
Off
am
Off
On Time
Off Time
:
Sleep
Off
On Time Volume
10
On time Channel
3
L
Move
the joystick
joystick up
leftor
or down
right to
minute,
then
move the
to select
select the
correct
minute.
C
;t
10
OnTime
OffTime
-:
: 30
am
- am
: _ am
Off
Off
Sleep
Off
On "TimeVolume
10
On time Channel
SAdjust
/ Move
3
ii Menu
Press the Menu button to exit.
Note
" Time setting will be reset when you pull out the Power cord if the PDP is ON.
(If you want to keep the time setting, turn the PDP off using the Power button on the remote control
or the Front Panek)
72
BN68-0071 IA-00esa_E
4 (walldel)
2004.4.30
3:8
PM
Page
7[
You can set your PDP to automatically turn off after a preset interval.
Press the
Menu 'Fund'on",
button. Move
thepress
joystick
or
down
to select
then
the up
joystick
to enter.
_
Time
English
h(
Caption
NR
Auto Power Off
,I
_
Off
Off
I,
_'
_
Off
I'
VOhip
Film Mode
Move
4 Select
;Menu
Move the joystick up or down to select "Time", then
press the joystick to enter.
Caption
3
JIR
_
Off
Auto Power Off
V-Chip
_
Off
_,
Move the joystick up or down to select "Sleep".
Clock
10:30
OnTime
am
- : - am
of ITime
:
am
Off
Off
(
10
OnTime Volume
OnTime Channel
3
so,oct Menu
.m_
Move
left oron.
right
select the
time from
interval
for the
the joystick
PDPto stay
Thetointervai
ranges
10 to 180 minutes.
Clock
10:30
am
OnTime
:
- am
Off
Off Time
:
am
off
On Time
Volume
10
On Time Channel
iI , Move
3
Seleot _"Menu
Press the Menu button to exit.
73
using the timers, you must set the PDP's clock, as described previously.
Setting the On/Oil 11met
i_::ii
Press the
Menu "Function",
button. Move
thepress
joystick
up or
down
to select
then
the joystick
to enter.
English
it??
Caption
NR
4
Off
Auto Power Off
_i
Off
4
Off
_"
V-Chip
Film Mode
_!
Move the joystick up or down to select "Time", then
press the joystick to enter.
3
Move the joystick up or down to select "On Time".
:
_;Move
Select
[ Menu
Language
i ime
_
English
CloCk
(}
10:30 am
- : - - am
7 ff
Off Time
Sleep
On Time Volume
:
am
Off
Off
Off
10
Ontime Channel
Move
3
Select
: Menu
ii/iiiiii
Move
the joystick
joystick up
leftor
or down
right to
then
move the
to select
seiect hour,
the correct
hour.
Clock
10:30
J
am
7 :--
OffTime
:
-
am
Off
am
Off
s0op
off
OnT,
moVolome
3
lo
On time Channel
Move the joystick left or right to select minute, then
move the joystick up or down to select the correct
minute.
Clock
10 : 30
am
7:30
am
Off
am
Off
(:
Off Time
:
OnTk
voloroe
,o
S,oep
On _imeChannel
Adjust
74
Move
3
Menu
Move
Ieft joystick
or right up
to select
or
"On", the
thenjoystick
move the
down "Off"
to select
"Off" or "On".
Clock
10:30
am
7:30_m On
Off Time
:
am
Off
Sleep
O'f
On Time Volume
10
On time Channel
3
i_i!iiiiiiii!!iii
;_Adjust
Move
_; Menu
to
If you
select
want
the to"Off
set Time".
Off Time, move the joystick down
Set the "Off Time" just as you set "On Time".
Clock
OnTime
(
Sleep
OnTime Channel
8
12:00
7:30
:
am
am
On
am
Off
Off
3
Press the Menu button to exit.
Note
"
If you set to On Time or Off Time, the Power Indicator on the Front Panel is changed to Green.
75
BN68-00711A-00esaE4(walldel)
2004.4.30
3:8
PM
Page
76_>
The oreferred channel ana vowme can De set foi wnen me timer automatical y turns on me TV.
Press tr/e
Menu "Function
button.
Movemen
tr/eoress
ioysrtcK
aown
to select
the
to enter.
up
or
oystick
English
Time
Caution
Nr_
Aulo Power
Off
•
Off
•
Off
•
Off
•
V-Chb
Film Mode
L_
Move
Select
Men[
Move me joystick up or aown to select "Time" men
oress me oystick to enter.
Language
_
English
_H
3aution
Auto Power Off
4
Off
•
Off
V-Chip
Film Mode
_
Move me oystlcK uD or aowr to select "Or Time
Volume
Move me joystick eft or -_gnr to adiust volume evel,
Move
Enter
Monk
]lock
am
On Time
- - am
OffTime
Off
am
Sleep
Off
Off
)n Time Channel
Move
Move
rne joystick JDor aown to select On Time
Channel'
Move me joystick eft or -_g_" to select the channel.
4>
Select
4on[
]lock
m
76
3
am
3n "Time
- - am
Off
3ff Time
-
Off
am
Sleep
Off
)n "[]me Volume
10
Move
Select
Men[
BN68-00711A-00esa_E_4(walldel)
2004.4.30
3:8 PM
Page
77_
Selecting a Menu Language .....................................................
78
Viewing Closed Captions .........................................................
79
Digital Noise Reduction ...........................................................
80
Setting Auto Power Off ...........................................................
81
Using the V-Chip .....................................................................
82
Selecting the Film Mode ...........................................................
88
Press the
Menu "Function",
button. Move
thepress
joystick
or
down
to select
then
the up
joystick
to enter.
!:i
':
English
T_m_
Caption
NR
_
Off
Auto Power Off
'_
Off
_1
Off
J'
V Chip
Film Mode
Move
Select
Move the joystick Ieft or right to select the appropriate language : English, Francais or EspaBoL
;
i_
Menu
iiii _i_I
< Frangais
k
Heure
L6gende
R6cuc, bruit
_
Oft
Eteinte
'_
Off
aklto
_"
V-Chip
i
Press the Menu button to exit.
78
Modo,l,r_, o_ ,
D@U
Choisir
Menu
BN68-00711A-00esa_E4(walldel)
2004.4.30
3:8 PM
Page
7!
Your TV decodes and displays the closed captions that are broadcast with certain
TV shows. These captions are usually subtitles for the hearing impaired or foreigm
language translations. All VCRs record the closed caption signal from television
programs, so home-recorded video tapes also provide closed captions. Most prerecorded commercial video tapes provide dosed captions as well. Check for the
closed caption symbol in your television schedule and on the tape's packaging: IT6q.
Note: The Caption feature does not work with DVD or DTV signals.
Press the
Menu "Function",
button. Move
thepress
joystick
or
down
to select
then
the up
joystick
to enter.
English
Time
Move
the joystick
up ortodown
then press
the joystick
enter.to select "Caption",
;;i;i;})x;
Language
_
English
Time
<
<
NR
_
Off
V-ChipAUto
Power Off
4
Off
_"
Y
Move
the joystick left or right to turn closed captiom
ing on/off.
(a
o
<
On
Mode
_
Caption
Channel
{
2
Move
Select
Menu
Move
the joystick
joystick left
up or
select"Caption"
"Mode", then
move the
or down
right totoselect
or
"Text."
Depending on the particular broadcast, it might be
necessary to make changes to "Channels" and
"Field': Move the joystick up, down, left and right
to make the changes. (Follow the same procedure
as in steps 3~4 above.}
Press the Menu button to exit.
Note
" Different channels and fields display different information: Field 2 carries additional information
that supplements the information in Field 1. (For example, Channel 1 may have subtitles in English,
while Channel 2 has subtitles in Spanish.
79
If the broadcast signal received by your TV is weak, you can activate the Digital Noise
Reduction feature to help reduce any static and ghosting that may appear on the screen.
Press the
Menu "Function",
button. Move
thepress
joystick
or
down
to select
then
the up
joystick
to enter.
_!
;i
,:
English
T_mo
Caption
NR
'_
Off
_*
Auto Power Off
'_
Off
_'
_1
Off
V Chip
Film Mode
Move
2
Select
;
Menu
Move the joystick up or down to select "NR".
Language
Time
_
English
Caption
Off
Auto Power Off
_
Off
_!
Off
V-Chip
Film Mode
Move
3
Move the joystick left or right to select "On".
i_
':Menu
:
Language
Time
Press the Menu button to exit.
8O
:::::7
Select
_
English
BN68-00711A-00esa_E4(walldel)
2004.4.30
3:8 PM
Page
8_
The PDPcan be set to turn off automatically if no buttons are pressed for 3 hours
after the PDPturns on via the On timer.
Press the
Menu "Function",
button. Move
thepress
joystick
or
down
to select
then
the up
joystick
to enter.
English
Time
Cap_ion
NR
_
Off
Auto Power Off
<
Off
'_
Off
J"
VChip
Film Mode
_Move
Select
I,
;Menu
Move the joystick up or down to select "Auto Power
Off".
3
Move the joystick left or right to select "On".
Language
Time
,t
English
Press the Menu button to exit.
NJ__£
'_ If the Off timer is set, Auto Power Off wiJJnot function.
'_ The power will be turned off automatically after 15 minutes if the PDPis ON and there is no input
signal. (For instance, if you select a channel without a signai while in TV mode or when there is no
input signal after selecting an output signal}
81
The V-Chip feature automatically locks out programs that are deemed inappropriate
for children. The user must enter a PIN (personal ID number) before any of the V-Chip
restrictions are set up or changed.
Note : When the V-Chip feature is activated, the HP and auto channel program features
do not function.
Up
1
Press the Menu button. Move the joystick up or
down to select "Function", then press the joystick
to enter.
/
English
_
English
Time
Move the joystick up or down to select "V-Chip",
then press the joystick to enter.
£ iiii ii
Language
Time
Caption
NR
Auto Power Off
_
4
Off
On
The
message
"Enter Pin" wiJJappear. Enter your
4-digit
PIN number.
Note: The default PIN number of a new TV set is
"0-G0-0/'
TTTT TT
The
Move
joystick
up or"V-Chip"
down toscreen
select wiJJappean
"Change Pin,"
thenthe
press
the
joystick to enter.
V-Chip Lock
TV GuideLines
_
No
_"
MPAARating
I;
{
The Change pin screen wiJJ appear. Choose any
4-digits for your PIN and enter them.
As soon as the 4 digits are entered, the "Confirm
New Pin" screen appears. Re-enter the same 4
digits. When the Confirm screen disappears, your
HN has been memorized.
Press the Menu button to exit.
Nof e
"
82
If you forget the HN, press the remote<ontroJ buttons in the following sequence, which resets the pin
to 0-0-G0 : Power Off @ Mute @ 8 @ 2 @ 4 @ Power On.
l0
Press the
Menu "Function",
button. Move
thepress
joystick
up or
down
to select
then
the joystick
to enter.
English
Time
Caption
NR
_
01I
V-ChipAuto
Power Off
_
Off
_"
Move
the joystick
up ortodown
then press
the joystick
enter.to select "V-Chip",
The
message
"Enter Pin" wiJJappear. Enter your
4-digit
PIN number.
Theenable
"V-Chip"
appear.
To
the screen
V-Chip will
feature,
move the joystick to
the right so that the "V-Chip Lock" field is Yes.
(Move the joystick to the Jeffor right wiJJalternate
between Yes and No.}
V {;
_
Yes
TV GuideLines
MPAA Rating
Change Pin
Move
Select
Menu
Press the Menu button to exit.
83
t0Set
up
'
First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.)
Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating.
Press the
Menu "Function",
button. Move
thepress
joystick
or
down
to select
then
the up
joystick
to enter.
English
Time
Caption
NR
AUtO Power
Off
'_
Off
I,
_
Off
_"
'_
Off
V-Chip
Film Mode
Move
Move the joystick up or down to select "V-Chip",
then press the joystick to enter.
Select
;
_"
Menu
w__
Language
_
EngJish
F
Time
Cap_ion
:
NR
_
Off
Auto Power Off
4
On
_
The message
"Enter Pin" wiJJappear. Enter your
4-digit
PiN number.
The
screen
appear.
Move"V-Chip"
the joystick
up will
or down
to select "TV Guidelines", press the joystick to enter.
V-Chip Lock
4
No
V
MPAA Rating
Change Pin
The "TV guideJ'nes' screen wiJJappear. Move the
joystick up or down to select one of the six agebased categories:
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
84
Young children
Children 7 and over
General audience
Parental guidance
Viewers 14 and over
Mature audience
TV-G
U
TV-PG
U
U
U
U
U
TV-14
U
U
U
U
U
TV-MA
U
U
U
U
Move
i Select
i: Menu
6
At this point, one of the TV-Ratings is selected_
Move the joystick to the right: Depending on your existing setup, a letter "U" or "B" wiJJstart
blinking_
(U= UnbJocked, B= Blocked)
While the "U" or "B" is blinking, move the joystick up or down to block or unblock the
category_
Move the joystick to the right to save the TV guidelines. A W-Rating will be seIected,
and no letters wiJJ Mink.
To select a different TV-Rating, move the joystick up or down and then repeat the process.
Note 1: The TV-Y7, TV-PG, TV-14 and TV-MA have additional options. See the next step to
change any of the following sub-ratings:
FV: Fantasy violence
D: Sexually Seggesive Dialog
L: Adult Language
S: Sexual situation
V: Violence
Note 2: The V-Chip wiJJautamaticaJIy Hock certain categories that are "more restrictive".
For example, if you block "TV-Y" category, then TV-Y7 wiJJautomatically be blocked.
Similarly, if you Mock the TV-G category, then all the categories in the "young adult" group
will be blacked (TV-G, TV-PG, TV-14 and TV-MA}. The sub-ratings (DeL, S, V) work together
similarly. (See next section.)
7
How to set the FV, D, L, S and V sub-ratings.
First, select one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4_ on
previous page)_
Next, while the TV-Rating is selected, repeatedly move the joystick to the right.
This will cycle through the available sub-ratings (FV,L, S, D or V)_
A blinking letter ('U" or "B") will be displayed for each sub-rating. While the "U" or "B" is
blinking, move the joystick up or down to change the sub-rating_
Move the joystick to the right to save the TV guidelines. A TV-Rating will be selected and no
letters will select. To select a different TV-Rating_move the joystick up or down and then
repeat the process.
Note: The V-Chip wiJJautomatically block certain categories that are "More restrictive'_
For example, if you block "L" sub-rating in TV-PG, then the "L" sub-ratings in TV-14 and
TV-MA wiJJautomatically be blocked.
Press
the Menu
button based
to clear
screens.
(Or proceed to the next section_ and set up
additional
restrictions
on all
thethe
MPAA
codes).
Note
"
Note: These categories consist of two separate groups: TV-Y and TV-Y7 (young children
through age 7), and TV-G through TV-MA (everybody else). The TV-Yand TV-Y7 categories
are colored bJue_
The restrictions for these two groups work independently: If a household includes very young
children as well as young adults, the TV guidelines must be set up separately for each age
group. (See next step.)
85
gs:
G,PG,
PGo13,
R,N[o17,
×
TheMPAA rating systemusesthe Motion PictureAssociationof America (MPAA)system,and its main application is
for movies.When the V-Chiplock is on, the TVwill automatically block any programsthat are coded with abiection_
able ratings (eitherMPAA or TV-Ratings}.
Press the
Menu "Function",
button. Move
thepress
joystick
up or
down
to select
then
the joystick
to enter.
;
English
Time
Caption
NR
V-ChipAuto
Power
Move the joystick up or down to select "V-Chip",
then press the joystick to enter.
Off
Language
Time
_
Off
_"
_
Off
P"
*l
English
Caption
NR
4
Off
Auto
V : Power Off
4
On
The
message
"Enter Pin" will appear. Enter your
4-digit
PIN number.
The
"V_Chip" screenwill
Move
the to
joystick
to select"MPAA
Rating,"appear.
pressthe
ioystick
enter.down
V-Chip b3ck
TV GuideLines
AA
_
,t
No
:
Change Pin
ii
!iiii_i_iiii_i!i!iiiiiii_
The "MPAA rating" screenwill appear. MPAA category.
Moving the joystick up or down will cycle through the
MPAA categories:
General audience
G
(no restrictions).
PG
....................
_a.:_!_.!
._._!d_t_.g._t_ted:
.................................................................................................................
R
R(Restricted.
Childrenunder 17 shouldbe accompaniedby an adu[t}.
........................
x.!6'J_!t_
_nk):................................................................................................................................................................
NR
Not rated.
While a particular category is seiected, move the joystick to the right ta activate it.
A selected letter ('U" or "B'} v,,'iJJbe displayed. Move the joystick up or down to seiect "U" or"B'.
Move the joystick to the right to save the settings.
Note: The V-Chip wiJJautomatically block any category that is "more restrictive." For example,
if you block the "PG-13" category, then "Ri' "NC_I 7," and "X" wiJJautomatically be blocked also.
86
tO
TV
If the TV is tuned to a restricted channel, the V-Chip wiJJ block it. The screen wiJJgo blank
and the following message will appear: "Excessive rating."
To resume normal viewing, tune to a different channel using the number buttons.
Under certain conditions (depending on the rating of the local TV programs/the V-Chip might
lock out all the channels. In this case, use the V-Chip function for an "emergency escape":
Press the Menu button.
Move the joystick up or down to select "V-Chip", then press the joystick to enter.
Enter
your PIN
the V-Chip
Lock.number, and move the joystick to the right to temporarily disable
87
BN68-00711A-00esa_E_4(walldel)
2004.4.30
3:8
PM
Page
88<_>
Press me
Menu "button.
Move
meoress
]oysNcK
aown
to se.ec.tt
Function"
men
me L-_o.s_c..
iupv or
ti
to enter.
English
Time
Caution
Nr_
Aulo Power
Off
•
Off
•
Off
•
Off
•
V-Chb
Film Mode
z_J
Movemove
me joystick
up oreft
aown
to select
Film'On
Mode"
then
the oystick
or right
to select
or
"Off"
Move
Select
MenL
r_
Language
_b_
_ English p
Time
Ca_tior
oOn: Automatically senses ana processes film
s gnaIs from oil sources ana aa usrs me
oicture for optimum quality.
oOff: Switches off me Film moae.
&uto Power Off
•
Off
b
V-Chit
)r
Move:
_elec
Menu
Press the Menu button to exit.
o Film mode is supported in Video, S_Video, Component 480i.
/
88
BN68-00711A-00esa_E_4(walldel)
2004.4.30
3:8 PM
Page
89_
!¸!ill
iii_iiii!
_;!i_
Troubleshooting ............................................................................
Care and Maintenance ................................................................
90
91
Specifications ..............................................................................
92
T
Before you call a service technician, please scan this list of problems and possible solutions. It may save you
time and money.
P0ssibJeSduti0n
Check all wire connecnons.
m
Press the "Mode"
mode.
button to put your remote co _troJ in the "TV
Replace batteries
Check if the power plug is connected
Check to see that both the PDPand Thesource are plugged Jn
and turned cn.
Adjust the Brightness or Contrast settings.
Adjust the Size setfinc s,
90
BN68-00711A-00esa_E
4(walldel)
2004.4.30
3:8
PM
Page
9[
With proper care, your PDPwill give you many years of service. Please follow these guidelines to get
the maximum performance from your PD£
J4entiJyingPr0BJems
'_
'_
'_
'_
Do not put the PDP near extremely hot, cold, humid or dusty places.
Do not put the PDP near appliances that create magnetic fields.
Keep the ventilation openings clean
Do not place the PDP on a rough and slanted surface, such as cloth or paper.
Liquids
'_ Do not place liquids near or on the PD£
Cabinet
'_ Never open the cabinet or touch the parts inside.
,_ Wipe your PDPwith a clean, dry cJoth_Never use water, cleaning fluids, wax, or chemicals.
'_ Do not put heavy objects on top of the cabinet.
Temperature
,_ If your PDP is suddenly moved from a cold to a warm place, unplug the power cord for at least two
hours so that moisture that may have formed inside the unit can dry completely.
91
Exterior design and product specifications are subject to change without prior notice to improve
the performance of this product.
PDP4294LV
1027 (W} X 79 (D}X 630.5 (HI mm; 40.43 (W) X 3.11 (D}X 24.82(H)inches
54 (W) X 31.5 (D1X220 (H)mm ; 2!3 (W} X 124 (D)X 8.66 (H}inches
31 kg ; 68.34 Ibs {37.6 kg ; 82.89 Ibs (with stand)}
150g (includingbatteries); 0.331bs
120V~, 60Hz
370 Watts
852(H)x 480(V)
]07 Cm/42 inches
VHF,UHF(750 unbalanced}
VIDEO
SNIDEO
COMPONENT1 - 480i / 480p / 720p / 1080i
COMPONENT2- 480i / 480p / 720p / 1080i
RGB: D-SUB15P
DVI
VIDEO/ SNIDEO
COMPONENT 1
COMPONENT2
PC(RGB)
DVI
10W+ 10W (8 c,2)
Subwoofer(500my RMSat 1KHz)
92
BN68-00711A-00esa_E
4(walldel)
2004.4.30
3:8
PM
Page
930
93
94
BN68-00711A-00esa_E
4(walldel)
2004.4.30
3:8
PM
Page
950
95
BN68o00711AoO0