Shure ULX-D_datasheet


Add to my manuals
7 Pages

advertisement

Shure ULX-D_datasheet | Manualzz

Wireless Systems

PGW PGX SLX ® ULX ® ULX-D TM UHF-R ® AXIENT TM

ULX-D

DIGITAL WIRELESS

Shure ULX-D™ Digital Wireless offers uncompromising 24-bit audio clarity and extremely efficient RF performance with single, dual, and quad channel receivers for any size professional sound reinforcement application.

Generations ahead of any other available system in its class,

ULX-D brings a new level of performance to professional sound reinforcement.

Uncompromising Professional Digital Wireless

• 24-bit/48 kHz digital audio that delivers incredibly clear and accurate sound reproduction

• 20 Hz – 20 kHz frequency range with flat response

• Greater than 120 dB dynamic range

• Wide selection of trusted Shure Microphones

Extremely Efficient and Reliable RF Performance

• Up to 64 MHz overall tuning range (region dependent)

• Up to 17 active transmitters in one 6 MHz TV channel (22 on an 8 MHz TV channel)

• High Density mode enables up to 63 active transmitters in one 8 MHz TV channel

• Rock-solid signal stability with no audio artifacts over the entire 100 meter range

• Optimized scanning automatically finds, prioritizes, and selects the cleanest frequencies available

Scalable, Intelligent Hardware

• Single (half-rack), Dual and Quad (full-rack) receiver form factors

• AES 256-bit encryption equipped for secure wireless transmission

• Dante™ digital networked audio over Ethernet

• Wireless Workbench ® 6 software compatible for advanced coordination, monitoring, and control

• Compatible with the Shure SB900 Rechargeable Battery and SBC chargers

APPLIcATIonS

Installed Sound

Critical Audio Performances

High channel counts

Secure Presentation

PRoDUcT HIGHLIGHTS

24-bit/48 kHz Digital

Wireless Audio

High Density Mode

Single, Dual, and Quad

Channel Receivers

Advanced Rechargeability

Dante

TM

Networked

Audio over Ethernet

ULX-D TM System Specifications

RF Carrier Range

Working Range

RF Tuning Step Size

Image Rejection

RF Sensitivity

Latency

Audio Frequency Response

Audio Dynamic Range

System Gain @ +10

Total Harmonic Distortion

−12 dBFS input, System Gain @ +10

System Audio Polarity

Operating Temperature Range

Storage Temperature Range

470–932 MHz, varies by region (See Frequency Range and Ouput Power table)

100 m

Note: Actual range depends on RF signal absorption, reflection and interference.

25 kHz, varies by region

>70 dB, typical

-98 dBm at 10 -5 BER

<2,9 ms

ULXD1: 20 Hz – 20 kHz (±1 dB)

ULXD2: 30 Hz – 20 kHz (±1 dB)

Note: Dependent on microphone type

XLR Analog Output: >120 dB, A-weighted

Dante Digital Output (Dual and Quad receivers): 130 dB (typical), A-weighted

<0,1%

Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin 3 of XLR output) and the tip of the 6,35 mm output.

-18°C to 50°C

Note: Battery characteristics may limit this range.

-29°C to 74°C

Note: Battery characteristics may limit this range.

Frequency Range

Band

G50

G51

G52

H51

H52

J50

K51

L50

Range (MHz)

470 to 534

470 to 534

479 to 534

534 to 598

534 to 565

572 to 636

606 to 670

632 to 696

L51

P51

632 to 696

710 to 782

R51 800 to 810

JB (Tx only) 806 to 810

AB (Rx and Tx) 770 to 810

Q51 794 to 806

X50 925 to 932

* accessible via password

Transmitter Output (mW)

1/10/20

1/10/20

1/10

1/10/20

1/10

1/10/20

1/10/20

1/10/20

1/10/20

1/10/20

1/10/20

1/10

“A” band (770.250-805.750): 1/10/20

“B” band (806.125-809.750): 1/10

1/10/20

1/10

Furnished Accessories

All Systems

PS41US*

95T9279*

95K2035

98A8994

90AZ8100

95A16941

80B8201

Handheld Systems

Power supply

1/2 Wave Receiver Antenna (2)

2‘ BNC Cable (2)

BNC Bulkhead Adapter (2)

Rackmout Hardware kit

5‘ ethernet cable

2 x AA batteries (bodypack systems)

95T9279 Microphone Clip (handheld systems)

95B2313 Handheld Zipper Bag (bodypack systems)

Bodypack Systems

95G9043* Bodypack Antenna

95A2313 Bodypack Zipper Bag (bodypack systems)

* region specific part # (US part listed)

NOTE:

This Radio equipment is intended for use in professional sound reinforcement and similar applications.

This Radio apparatus may be capable of operating on some frequencies not authorized in your region.

Please contact your national authority to obtain information on authorized frequencies and RF power levels for wireless microphone products.

Rechargeable Power Management (sold separately)

SB900 Rechargeable Battery

ULX-D transmitters are compatible with the SB900 lithium-ion rechargeable battery, which provides up to 12 hours of continuous use and precise tracking of remaining life and charge cycle details.

SBC200 Dual Docking Recharging Station

This compact and portable unit charges batteries while in transmitters or out. Up to

4 SBC200‘s can be chained together to run off one power supply.

SBC800 Eight Battery Recharging Station

This compact and portable unit charges up to 8 SB900 batteries to full capacity within 3 hours, with status LEDs to indicate power levels. SB900 batteries fit securely in the charger for easy, efficient storage and transport.

Battery Runtime

Battery Type

SB900

Alkaline

NiMH

Li-primary

1 mW

>11 hours

<11 hours

<11 hours

12,5-18 hours

10 mW

>11 hours

<11 hours

<11 hours

12,5-18 hours

20 mW

>7 hours

<5,5 hours

<8 hours

9,5-12 hours www.shure.com

component Specifications

ULXD4 Digital Wireless Receiver

Overview

The Shure ULXD4 is a half-rack wireless receiver for use with ULX-D TM Digital Wireless Systems. With an expansive set of professional features, including 24-bit/48kHz digital audio quality, efficient and intelligent RF performance, and AES 256-bit encryption, ULX-D offers uncompromising wireless tailored for professional sound reinforcement.

Up to 72 MHz tuning range

Digital predictive switching diversity

Intelligent scanning automatically finds the cleanest frequencies to be manually deployed to transmitters over IR sync

Interference detection and alerts provided on both the receiver and WWB6

Front panel gain adjustment buttons provide up to 60 dB additional gain

AES 256-bit encryption-enabled for applications where secure transmission is needed

Ethernet networking for streamlined setup across multiple receivers, WWB6 integration (coming soon), and AMX and Crestron control

Support for frequency coordination with Axient Spectrum Manager (coming soon)

Rugged metal chassis

Intuitive front panel LCD menu and controls

Easily readable LCD with adjustable contrast and brightness

Audio and RF LED meters with peak indicator

Various options of front panel lockout

XLR and ¼” outputs

Remoteable ½ wave antennas

Furnished rack hardware, antenna front mount cables, and ethernet cable

Product Specifications

Dimensions

Weight

Housing

RF Input

Spurious Rejection

Connector Type

Impedance

Bias Voltage

Audio Output

Gain Adjustment Range

Configuration

Impedance

Full Scale Output

Mic/Line Switch

Phantom Power Protection

Networking

Power Over Ethernet (PoE)

Network Interface

Network Addressing Capability

Maximum Ethernet Cable Length

197 mm x 171 mm x 42 mm, H x W x D

913 g, without antennas

Galvanized Steel

>80 dB, typical

BNC

50 Ω

12 - 13 V DC, 170 mA maximum, per antenna

-18 to +42 dB in 1 dB steps (plus Mute setting)

1/4” (6,35 mm): Impedance balanced (Tip = audio, Ring = no audio, Sleeve = ground)

XLR: Balanced (1 = ground, 2 = audio +, 3 = audio -)

1/4” (6,35 mm): 100 Ω (50 Ω Unbalanced)

XLR: 100 Ω

1/4” (6,35 mm): +12 dBV

XLR: LINE setting = +18 dBV, MIC setting = -12 dBV

30 dB pad

1/4” (6,35 mm): Yes

XLR: Yes

No, protected

Single Port Ethernet 10/100 Mbps

DHCP or Manual IP address

100 m

ULXD4

Digital Wireless Receiver

ULXD4 Front Panel sync

ENTER

EXIT

SCAN control RF

AB audio

OL

OL gain power push

ULXD4 www.shure.com

12V                OUT

150  mA antenna  .  B

ULXD4 Back Panel

15V  0.6A

power line mic mic  /  line inst  /  aux

12V                OUT

150  mA antenna  .  A www.shure.com

component Specifications

ULXD4D Dual Channel Digital Wireless Receiver

Overview

The Shure ULXD4D Dual Channel Digital Wireless Receiver offers two channels of uncompromising audio quality, RF signal stability, and advanced setup features in a space-efficient single rack unit. Digital wireless processing delivers premium 24-bit/48 kHz audio and RF spectrum efficiencies that dramatically increase the number of available compatible channels. With an expansive set of enhanced features including AES 256-bit encryption for security and Dante™ digital networking for audio over Ethernet, the ULXD4D brings a new level of performance to professional sound reinforcement.

Two receivers in a rugged 1RU metal chassis with internal power supply

Up to 72 MHz tuning range (region dependent)

Digital predictive switching diversity

High Density mode optimizes ULX-D systems to simultaneously operate significantly more channels in applications up to 30 meters

RF cascade ports allow distribution of RF signal to another unit

Optimized scanning automatically finds, and prioritizes the cleanest frequencies to be manually deployed to transmitters over IR sync

Bodypack Frequency Diversity ensures uninterrupted audio for mission-critical applications

AES 256-bit encryption-enabled for secure transmission

Audio summing routes both audio channels to each XLR receiver output

Dante™ digital networked audio over Ethernet

Individual gain controls, LED meters, and XLR outputs for each channel

Up to 60 dB independently adjustable gain for each channel

Ethernet networking for streamlined frequency coordination and deployment across multiple receivers

Wireless Workbench ® 6 (WWB6) software integration for advanced coordination, monitoring, and control (coming soon)

AMX and Crestron control

AXT600 Axient™ Spectrum Manager compatible

Interference detection and alerts provided on both the receiver and WWB6

Intuitive front panel LCD menu and controls with various options of lockout

Audio and RF LED meters with peak indicator

XLR connectors with switchable mic/line output level

Remoteable ½ wave antennas

Ethernet cable included

Product Specifications

Dimensions

Weight

Housing

Power Requirements

RF Input

Spurious Rejection

Connector Type

Impedance

Bias Voltage

Audio Output

Gain Adjustment Range

Configuration

Impedance

Full Scale Output

Mic/Line Switch

Phantom Power Protection

Networking

Network Interface

Network Addressing Capability

Maximum Ethernet Cable Length

RF Cascade Output

Connector Type

Configuration

Impedance

Insertion Loss

44 mm x 482 mm x 274 mm, H x W x D

3,36 Kg, without antennas

Steel; Extruded Aluminum

100 to 240 V AC, 50 - 60 Hz, 0,26 A max.

>80 dB, typical

BNC

50 Ω

12 - 13 V DC, 150 mA maximum, per antenna

-18 to +42 dB in 1 dB steps (plus Mute setting)

XLR: Balanced (1 = ground, 2 = audio +, 3 = audio -)

100 Ω

LINE setting = +18 dBV, MIC setting = -12 dBV

30 dB pad

Yes

Dual Port Ethernet 10/100 Mbps, 1 Gbps

DHCP or Manual IP address

100 m

BNC: For connection of 1 additional receiver

Unbalanced, passive

50 Ω

0 dB

ULXD4D

Digital Wireless Receiver

IR control

ENTER

EXIT

SCAN push

RX1

SEL

RF

AB

OL audio

OL gain syn c

RX2

SEL

RF

AB

OL audio

OL gain syn c

ULXD4D Front Panel

B output 2 output 1

Secondary Primary

A power line mic line mic

ULXD4D Back Panel www.shure.com

component Specifications

ULXD4Q Quad Channel Digital Wireless Receiver

Overview

The Shure ULXD4Q Quad Channel Digital Wireless Receiver offers four channels of uncompromising audio quality, RF signal stability, and advanced setup features in a space-efficient single rack unit. Digital wireless processing delivers premium 24-bit/48 kHz audio and RF spectrum efficiencies that dramatically increase the number of available compatible channels. With an expansive set of enhanced features including AES 256-bit encryption for security and Dante™ digital networking for audio over Ethernet, the ULXD4Q delivers the most wireless performance in a single rack space.

Four receivers in a rugged 1RU metal chassis with internal power supply

Up to 72 MHz tuning range (region dependent)

Digital predictive switching diversity

High Density mode optimizes ULX-D systems to simultaneously operate significantly more channels in applications up to 30 meters

RF cascade ports allow distribution of RF signal to another unit

Optimized scanning automatically finds, and prioritizes the cleanest frequencies to be deployed to transmitters over IR sync

Bodypack Frequency Diversity ensures uninterrupted audio for mission-critical applications

AES 256-bit encryption-enabled for secure transmission

Audio summing routes two or more audio channels to combinations of receiver outputs. Use each channel’s gain adjustment to reach the desired mix.

Dante™ digital networked audio over Ethernet

Individual gain controls, LED meters, and XLR outputs for each channel

Up to 60 dB independently adjustable gain for each channel

Ethernet networking for streamlined frequency coordination and deployment across multiple receivers

Wireless Workbench ® 6 software integration for advanced coordination, monitoring, and AMX and Crestron control

Compatible with the AXT600 Axient™ Spectrum Manager

Interference detection and alerts provided on both the receiver and WWB6

Intuitive front panel LCD menu and controls with lockout feature

LCD with adjustable contrast and brightness

Audio and RF LED meters with peak indicator

XLR connects with switchable mic/line output level

Remoteable ½ wave antennas

Ethernet cable included

Product Specifications

Dimensions

Weight

Housing

Power Requirements

RF Input

Spurious Rejection

Connector Type

Impedance

Bias Voltage

Audio Output

Gain Adjustment Range

Configuration

Impedance

Full Scale Output

Mic/Line Switch

Phantom Power Protection

Networking

Network Interface

Network Addressing Capability

Maximum Ethernet Cable Length

RF Cascade Output

Connector Type

Configuration

Impedance

Insertion Loss

44 mm x 482 mm x 274 mm, H x W x D

3,45 Kg, without antennas

Steel; Extruded Aluminum

100 to 240 V AC, 50-60 Hz, 0,32 A max.

>80 dB, typical

BNC

50 Ω

12 - 13 V DC, 150 mA maximum, per antenna

-18 to +42 dB in 1 dB steps (plus Mute setting)

XLR: Balanced (1 = ground, 2 = audio +, 3 = audio -)

100 Ω

LINE setting = +18 dBV, MIC setting = -12 dBV

30 dB pad

Yes

Dual Port Ethernet 10/100 Mbps, 1 Gbps

DHCP or Manual IP address

100 m

BNC: For connection of 1 additional receiver

Unbalanced, passive

50 Ω

0 dB control

ULXD4Q

Digital Wireless Receiver

ENTER

EXIT

SCAN

RX1

SEL

RF

AB

OL audio

OL gain syn c

RX2

SEL

RF

AB

OL audio

OL gain sync

RX3

RF

AB

OL audio

OL gain sync

RX4

RF

AB

OL audio

OL gain power syn c

IR push

ULXD4Q Front Panel

B A output 4 output 3 output 2 output 1

Secondary Primary line mic line mic line mic line mic

ULXD4Q Back Panel www.shure.com

component Specifications

ULXD2 Wireless Handheld Transmitter

Overview

The Shure ULXD2 is a handheld wireless transmitter compatible with ULX-D TM Digital Wireless Systems. Offering premium 30 Hz – 20 kHz audio quality, advanced rechargeability options, and a wide selection of interchangeable Shure microphone heads, the ULXD2 delivers uncompromising wireless performance for professional sound reinforcement applications. The ULXD2 is offered with SM58 ® , SM86, SM87A, Beta 58A ® , Beta 87A, Beta 87C, and KSM9.

• 30 Hz to 20 kHz range with flat frequency response (actual response is microphone dependent)

• Interchangeable Shure microphone cartridges, including the legendary SM58 ®

• >120 dB dynamic range

• 1, 10, and 20 mW selectable RF output power

• 5 segment battery fuel gauge

• Shure lithium-ion rechargeable battery pack provides up to 12 hours of battery life, precision metering in hours and minutes, and zero memory effect

• Up to 11 hours continuous use with 2 x AA batteries

• Backlit LCD with easy to navigate menu and controls

• 100 meter operating range

• Rugged metal construction

• Independent frequency and power lockout

Product Specifications

Gain Offset Range

Battery Type

Battery Runtime

@ 10 mW

Dimensions

Weight

Housing

Audio Input

Configuration

Maximum Input Level

1 kHz at 1% THD

Preamplifier Equivalent Input Noise (EIN)

System Gain Setting ≥ +20

RF Output

Antenna Type

Occupied Bandwidth

Modulation Type

Power

0 to 21 dB (in 3 dB steps)

Shure SB900 Rechargeable Li-Ion or AA/LR6 batteries (1,5 V)

Shure SB900: >11 hours

Alkaline: 11 hours (See Battery Runtime Chart)

256 mm x 51 mm L x Dia.

340 g, with SM58 head, without batteries

Machined aluminum

Unbalanced

145 dB SPL (SM58), typical

Note: Dependent on microphone type

120 dBV, A-weighted, typical

Integrated Single Band Helical

<200 kHz

Shure Proprietary Digital

1 mW, 10 mW, 20 mW

(See Frequency Range and Ouput Power table, varies by region)

Microphone Options

ULXD2/SM58

ULXD2/SM86

ULXD2/SM87A

ULXD2/BETA 58

ULXD2/BETA 87A

ULXD2/BETA 87C

ULXD2/KSM9

ULXD2 Handheld Transmitter with SM58 Cardioid Microphone

ULXD2 Handheld Transmitter with SM86 Cardioid Microphone

ULXD2 Handheld Transmitter with SM87A Supercardioid Microphone

ULXD2 Handheld Transmitter with Beta 58A Supercardioid Microphone

ULXD2 Handheld Transmitter with Beta 87A Supercardioid Microphone

ULXD2 Handheld Transmitter with Beta 87C Cardioid Microphone

ULXD2 Handheld Transmitter with KSM9 Cardioid/Supercardioid Microphone

ULXD2 on

ULXD2

Wireless Handheld Transmitter www.shure.com

component Specifications

ULXD1 Wireless Bodypack Transmitter

Overview

The ULXD1 is a wireless bodypack transmitter compatible with ULX-D TM Digital Systems. With a rugged yet lightweight aluminum case providing threaded 4-pin mini XLR-connector, the ULXD1 delivers uncompromising audio quality and RF performance, and advanced rechargeability options for professional sound reinforcement applications.

20 Hz to 20 kHz range with flat frequency response (actual response is microphone dependent)

AES 256-bit encryption-enabled for applications where secure transmission is needed

>120 dB dynamic range

1, 10, and 20 mW selectable RF output power

5 segment battery fuel gauge

Shure lithium-ion rechargeable battery pack provides up to 12 hours of battery life, precision metering in hours and minutes, and zero memory effect

Up to 11 hours continuous use with 2 x AA batteries

Backlit LCD with easy to navigate menu and controls

100 meter operating range

Rugged metal construction

Independent frequency and power lockout

Product Specifications

Gain Offset Range

Battery Type

Battery Runtime

@ 10 mW

Dimensions

Weight

Housing

Audio Input

Connector

Configuration

Impedance

Maximum Input Level

1 kHz at 1% THD

Preamplifier Equivalent Input Noise (EIN)

System Gain Setting ≥ +20

RF Output

Connector

Antenna Type

Impedance

Occupied Bandwidth

Modulation Type

Power

0 to 21 dB (in 3 dB steps)

Shure SB900 Rechargeable Li-Ion or AA/LR6 batteries (1,5 V)

Shure SB900: >11 hours

Alkaline: 11 hours (see battery runtime chart)

86 mm x 66 mm x 23 mm (H x W x D)

142 g, without batteries

Cast aluminum

4-Pin male mini connector (TA4M) prepared for Shure microphones with threaded connectors

Unbalanced

1 MΩ

Pad Off: 8,5 dBV (7,5 Vpp)

Pad On: 20,5 dBV (30 Vpp)

120 dBV, A-weighted, typical

SMA

1/4 wave

50 Ω

<200 kHz

Shure Proprietary Digital

1 mW, 10 mW, 20 mW

(See Frequency Range and Ouput Power table, varies by region)

Microphone Options (see catalog for more)

WL93

WL183

WL184

WL185

WL50

WL51

WH30

WCM16

WBH53

WBH54

WB98H/C

WL93 condenser capsule, omnidirectional lavalier mic

WL183 condenser capsule, omnidirectional lavalier mic

WL184 condenser capsule, supercardioid lavalier mic

WL185 condenser capsule, cardioid lavalier mic

WL50 condenser capsule, omnidirectional lavalier mic

WL51 condenser capsule, cardioid lavalier mic

WH30 condenser capsule, cardioid headworn mic

WCM16 condenser capsule, hypercardioid headworn mic

WBH53 condenser capsule, omnidirectional headworn mic

WBH54 condenser capsule, supercardioid headworn mic

WB98H/C condenser capsule, cardioid instrument clip mic

ULXD1

ULXD1 Wireless Bodypack Transmitter www.shure.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement