Emerson CF654OB00 Owner`s manual

Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
READ AND SAVE THESE INSTRUCTIONS
WET LOCATION
52” Ceiling Fan
Owner's Manual
Model No.
CF654AW00
CF654OB00
CF654ORB00
CF654WB00
CF654WW00
Net Weight:
18.7 Lbs.
ENERGY STAR
Part No. F40BP73360000
Form No. BP7336
U.L. Model No.: CF653
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means
to prevent power from being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to
the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan
without blades.
2. All wiring must be in accordance with the National Electrical Codes “ANSI/NFPA 70-1999” and Local Electrical
Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be grounded as a
precaution against possible electrical shock. Electrical installation should be made or approved by a licensed
electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds. Use
only U.L. outlet boxes listed as “Acceptable for Fan Support”, and use the mounting screws provided with the
outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and
may need to be replaced. Consult a qualified electrician if in doubt.
4. The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance for an
8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the
fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not specifically
approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson Electric Co. could result in personal injury or property
damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
NOTE: This product is suitable for use in wet locations when installed in a GFCI protected branch circuit.
DATE CODE:
The date code of this fan may be found on
the box, stamped in ink on a white label.
You should record this data above and keep
it in a safe place for future use.
2
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
THIS FAN IS SUITABLE FOR WET LOCATIONS SUCH AS
PORCHES, PATIOS, AND DECKS.
This Manual is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Up to 50 ft.
50 - 100 ft.
One Phillips head screwdriver
One stepladder
One wire stripper
Three wire connectors (supplied).
!
MATERIALS
Wire Size A.W.G.
14
12
WARNING
Before assembly your ceiling fan, refer to section on
proper method of wiring your fan (page 7). If you feel
you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.
Wiring, electrical box and box connectors must be of
type required by the local code. The minimum wiring
would be a 3-conductor (2-wire with ground) of following sizes:
Unpacking Instructions
For your convenience, check-off boxes are provided next to each assembly step. As each step is completed, place a check mark in the box. This will insure that all steps have been completed and will be helpful
in finding your place should you be interrupted.
!
G. One loose parts bag containing:
1. Sixteen M5 x 6 washer head blade screws
2. One M6 x 14 flange screw with lockwasher
3. One wood ball
4. Three wire connectors
5. One clevis pin
6. One hairpin clip
7. Two threaded studs
8. Two lockwashers
9. Two knurled knobs
10. One chain coupling
NOTE: Place the parts from the loose parts bag in
a small container to keep them from being lost.
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by
Emerson Electric Co. could result in personal injury
or property damage.
A
B
Check to see that you have received the following
parts:
A.
B.
C.
D.
E.
F.
C
Fan motor assembly
One ceiling cover
Five blade flanges
Five fan blades
One hanger ball/downrod assembly
One hanger bracket.
D
G
E
F
3
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
How to Put Your Ceiling Fan Together
1. Remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the pin from the
downrod, then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in step 5.
3. Tighten the two upper setscrews (Figure 2)
securely while pulling up on the downrod.
NOTE: The setscrews must be properly installed
as described above, or fan wobble could result.
4. Place the ceiling cover over the downrod, making
sure that the large opening faces upward
(Figure 3).
PIN
HANGER
BALL
DOWNROD
DOWNROD
SETSCREW
CEILING
COVER
Figure 1
RETIGHTEN
UPPER
SETSCREW
2. Unscrew the two upper setscrews (Figure 2) until
they clear the inside of the motor coupling. Then
separate, untwist and unkink the three 80” motor
leads. Route the motor lead wires through the
downrod. Align the clevis pin holes in the downrod
with the holes in the motor coupling. Install the
clevis pin and secure with the hairpin clip (Figure
2). The clevis pin must go through the holes in the
motor coupling and the holes in the downrod. Be
sure to push the straight leg of the hairpin clip
through the hole near the end of the clevis pin until
the curved portion of the hairpin clip snaps around
the clevis pin. The hairpin clip must be properly
installed to prevent the clevis pin from working
loose. Pull on the downrod to make sure the clevis
pin is properly installed.
5. Reinstall the hanger ball on the downrod as
follows (Figure 4) . Route the three 80” motor
leads through the hanger ball. Position the pin
through the two holes in the downrod and align the
hanger ball so the pin is captured in the groove in
the top of the hanger ball. Pull the hanger ball up
tight against the pin and securely tighten the
setscrew in the hanger ball. A loose setscrew
could create fan wobble.
!
WARNING
!
RETIGHTEN
UPPER
SETSCREW
Figure 3
WARNING
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are properly installed could result in the fan falling.
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrews are securely
tightened. Failure to verify that the pin and setscrews
are properly installed (as shown in Figures 2 & 3)
could result in the fan falling.
PIN
DOWNROD
UPPER
SETSCREW (2)
CLEVIS PIN
MOTOR
COUPLING
HANGER BALL
DOWNROD
HAIRPIN
CLIP
CEILING
COVER
SETSCREW
DOWNROD
Figure 4
6. The fan comes with blue, black and white leads
that are 80-inches long. Before installing the fan,
measure up approximately 6 to 9-inches above top
of hanger ball/downrod assembly. Cut off excess
leads and strip back insulation 1/2-inch from end of
leads.
CLEVIS
PIN
CLEVIS PIN
UNTIGHTEN
UPPER
SETSCREW
Figure 2
HAIRPIN
CLIP
UNTIGHTEN
UPPER
SETSCREW
4
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
6. Turn fan assembly upside down in preparation for
mounting fan blade assemblies.
Electrical Requirements
IMPORTANT: THE SIDE OF THE FAN BLADE
HAVING THE RIB LINE MUST BE FACING
UPWARDS AS SHOWN IN FIGURE 5.
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds.
7. Mount blade flanges to fan blades using three
M5 x 6 washer head screws per blade (Figure 5).
!
RIB LINE
(THIS SIDE UP)
M5 x 6 WASHER HEAD
BLADE SCREW (3)
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time
and remove the existing light fixture.
BLADE FLANGE
Figure 5
FAN BLADE
!
WARNING
!
WARNING
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
NOTE: Remove and discard the five shipping
spacers and screws from the motor hub.
!
8. Attach blade assembly to motor using two
M6 x 14 flange screws with lockwasher preassembled in flange. Make sure the screws are tightened
securely (Figure 6). Repeat this procedure for other
four blade assemblies.
NOTE: Take care not to scratch fan housing when
installing blades.
WARNING
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these instructions should be done or approved by a licensed electrician.
SWITCH HOUSING
M6 x 14 FLANGE SCREWS
WITH LOCKWASHERS (2)
MOTOR
HUB
Figure 6
9. You have now completed the assembly of your
new ceiling fan. You can now proceed with hanging
and the electrical wiring of your fan.
5
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
How to Hang Your Ceiling Fan
!
WARNING
!
WARNING
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 7).
CEILING
2.Carefully lift the fan from the foam pad and seat the
hanger ball/downrod assembly on the hanger
bracket that was just attached to the outlet box
(Figure 9). Be sure the groove in the ball engages
with the tab on the hanger bracket (Figure 8).
AT LEAST
7'
Figure 7
FLOOR
!
!
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
The outlet box and joist must be securely mounted
and capable of supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable for Fan
Support”.
!
WARNING
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
OUTLET
BOX
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
Figure 9
!
1. Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box
(Figure 8).
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
Figure 8
HANGER
BRACKET
TAB
6
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
!
!
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it
must be grounded for safe operation.
3. Screw the two threaded studs (supplied) into the
tapped holes in the hanger bracket.
4. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 11).
1.Connect the green grounding lead from the hanger
ball and the green grounding lead from the hanger
bracket to the grounding conductor of supply (this may
be a bare wire or wire with green colored insulation).
GROUND
WIRE
WIRE
CONNECTORS (3)
BLACK AND BLUE
FAN WIRES
WARNING
5. Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two
knurled knobs (supplied). (Figure 11). Tighten the
knurled knobs securely until the ceiling cover fits
snugly against the ceiling and the hole in the ceiling
cover is clear of the downrod. Your fan is now wired to
be turned on and off from the fan switch.
NOTE: CEILING COVER
OMITTED FOR CLARITY.
WHITE SUPPLY
(NEUTRAL)
CEILING COVER
GREEN WIRE
(GROUND)
FROM FAN
WHITE FAN
WIRE
LOCKWASHERS (2)
THREADED STUD
BLACK SUPPLY
(HOT)
KNURLED KNOB
Figure 11
Figure 10
NOTE: If you are using an Emerson light fixture
with your fan, remove the three screws securing
the switch housing cover to the switch housing
and remove the cover. Remove the screw plug
from the bottom of the switch housing cover and
install the light in accordance with the light kit
Owner's Manual.
2.Connect the fan motor white wire to the supply
white (neutral) wire using a wire connector
(supplied) (Figure 10). Connect the fan motor black
wire and blue wire to the supply black (hot) wire
using a wire connector (supplied) (Figure 10). Your
fan is now wired to be turned on and off from the
fan switch. After connections have been made, turn
leads upward and carefully push leads into the outlet box, with the white and green leads on one side
of the outlet box and the black and blue leads on
the other side of the outlet box.
!
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
6.Cut the 3-speed switch pull chain to a desired length
(optional). Connect the wood pendant (supplied) to
the 3-speed switch pull chain by sliding the wooden
pendant (small hole first) onto the pull chain. Attach
the chain coupler to the end of the chain and allow the
wooden pendant to fall down over the coupling.
7
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
Using Your Ceiling Fan
!
Energy Efficient
Use of Ceiling Fans
WARNING
Ceiling fan performance and energy savings rely heavily
on the proper installation and use of the ceiling fan.
Here are a few tips to ensure quality and product
performance.
To reduce the risk of fire or electrical shock, do not
use this fan with any solid-state speed control
device.
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box.
2. Check the operation of the fan by gently pulling on
the pull chain switch.
3. All fans are shipped from the factory with the
reversing switch positioned “down” to circulate air
downward.
4. If airflow is desired in opposite direction, turn your
fan OFF and wait for the blades to stop turning,
then slide the reversing switch to the “up” position,
and turn fan on again. The fan blades will turn in
the opposite direction and reverse the airflow.
Your fan model is equipped with a 4-position,
3-speed pull chain switch. The operating sequence
is as follows:
Three-Speed
1st Pull—HIGH
2nd Pull—Medium
3rd Pull—Low
4th Pull—OFF
Season
Summer
Winter
Choosing the Appropriate Mounting Location.
Ceiling fans should be installed, or mounted, in the
middle of the room and at least 7 feet above the floor
and 18 inches from the walls. If ceiling height allows,
install the fan 8 - 9 feet above the floor for optimal
airflow. Consult your Emerson Retailer for optional
mounting accessories.
Using the Ceiling Fan Year Round. In the summer,
use the ceiling fan in the counter-clockwise direction.
The airflow produced by the ceiling fan creates a windchill effect, making you "feel" cooler. Select a fan speed
that provides a comfortable breeze, lower speeds consume less energy. In the winter, reverse the motor and
operate the ceiling fan at low speed in the clockwise
direction. This produces a gentle updraft, which forces
warm air near the ceiling down into the occupied space.
Remember to adjust your thermostat when using your
ceiling fan - additional energy and dollar savings could
be realized with this simple step!
Turn Off When Not in the Room. Ceiling fans cool
people, not rooms. If the room is unoccupied, turn off
the ceiling fan to save energy.
REVERSING
SWITCH
SPEED
CONTROL
SWITCH
Reverse Switch Information
Rotation Direction
Switch Position
Counter-Clockwise
Down
Clockwise
Up
NOTE: The reversing switch is covered by a soft
vinyl rubber seal to prevent entry of water into the
switch cup assembly.
8
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
Maintenance
Accessories
1. Ceiling Fan Light Kits (see store or catalog).
2. Ceiling Fan/Light Controls (see store or catalog).
3. Downrod Extension Kits (see store or catalog).
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
!
!
WARNING
To reduce the risk of fire or electrical shock, do not
use this fan with any solid-state speed control
device.
WARNING
!
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by
Emerson Electric Co. could result in personal injury
or property damage.
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT
BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.
!
Trouble Shooting
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
SUGGESTED REMEDY
1. Reversing switch in neutral position.
2. Fuse or circuit breaker blown.
3. Loose power line connections to the fan, or loose
switch wire connections in the switch housing.
2. Fan sounds
noisy.
1. Blades not attached to fan.
2. Screws securing fan blade flanges to motor
are loose.
3. Wire connectors inside switch housing rattling.
4. Screws holding flanges to blades are loose.
3. Fan wobbles
or shakes
excessively.
1. Setscrew in motor coupling is loose.
2. Setscrew in hanger ball/downrod assembly is
loose.
3. Screws securing fan blade flanges to motor
are loose.
4. Fan blade flanges not seated properly.
5. Hanger bracket and/or ceiling outlet box is not
securely fastened.
6. Fan blades out of balance.
1. Make sure reversing switch position is all the way to one
side.
2. Check main and branch circuit fuses or circuit breakers.
3. Check line wire connections to fan and switch wire
connections in switch housing.
1. Attach blades to fan before operating.
2. Check to make sure the screws which attach the fan blade
flanges to the motor are tight.
3. Check to make sure wire connectors in switch housing
are not rattling against each other or against the interior
wall of the switch housing.
4. Tighten screws securely.
1. Tighten the setscrew securely in the motor coupling.
2. Tighten the setscrew in the hanger ball/downrod
assembly.
3. Check to be sure screws which attach the fan blade
flanges to the motor are tight.
4. Check to be sure the fan blade flanges seat firmly and
uniformly to the surface of the motor. If flanges are
seated incorrectly, loosen the flange screws and retighten
according to the procedure in the section on "How to Put
Your Ceiling Fan Together".
5. Tighten the hanger bracket screws to the outlet box,
and/or secure outlet box.
6. Interchanging an adjacent (side-by-side) blade pair can
redistribute the weight and result in smoother operation.
9
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
Repair Parts
1
1
9
2
9
9
9
9
9
9
3
9
4
8
7
9
6
5
9
Before discarding packaging material, be certain all parts
have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING
INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the
top housing.
For repair parts, phone 1-800-654-3545.
10
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
Repair Parts Listing
Key
No.
Service Part No.
Description
CF654WW01
CF654OB00
CF654WB00
CF654AW00
CF654ORB00
1
Hanger Assembly
761655
761655-9
761655-20
761655-21
761655-32
2
Ceiling Cover
760169
760169-24
760169-30
760169-32
760169-41
3
Blade Set (5)
762004
762004-1
762004-5
762004-4
762004-6
4
Flange Set (5)
763116-WW
763116-OB
763116-WB
763116-AW
763116-ORB
5
Switch Housing Cover
763117-WW
763117-OB
763117-WB
763117-AW
763117-ORB
6
Capacitor
763123
763123
763123
763123
763123
7
Speed Control Switch
763122
763122-1
763122-1
763122
763122-1
8
Reversing Switch
760360
760360-1
760360-1
760360
760360-1
9
Loose Parts Bag
Containing:
Threaded Stud (2)
Lockwasher (2)
Knurled Knob (2)
Screw, M5 x 6 Washer
Head Blade (16)
Screw, M6 x 14
Flange (1)
Lockwasher,
M6 x 14 (1)
Wire Connector (3)
Clevis Pin (1)
Hairpin Clip (1)
Pull Chain Wood Ball (1)
Pull Chain Coupling (1)
763118-1
763118
763118
763118-2
763118
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
BP7336
BP7336
BP7336
BP7336
BP7336
–
Owners Manual
11
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207
Authorized Emerson Fan Dealer www.NovaLightingStore.com 800-860-1207
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in
workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for thirty years from the date you purchased your ceiling fan. All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at
no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement
can be provided, Emerson will refund the actual purchase price of your fan. We will ship the repaired product or replacement
to you at no charge, but you are responsible for all costs or removal, reinstallation and shipping of the product to Emerson
Electric Co.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP
YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized
service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort
Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers
shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center.
Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible
for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and
tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL
DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential
damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product
does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Air Comfort Products
Part No. F40BP73360000
DIVISION OF Emerson Electric Co.
8100 W. Florissant ¥ St. Louis, MO 63136
Printed in China 11/06
Form No. BP7336
Emerson Fans Available at www.NovaLightingStore.com 800-860-1207