Samsung ML-3471ND Product specifications

LASER PRINTER
ML-347x Series
ML-3471ND/XAX
Basic Model : ML-3471ND
SERVICE
LASER PRINTER
Manual
The keynote of Product
Upgrade to Speed_up model(ML-347x)
of the ML-3050 serie
1. Speed: Up to 33ppm (Ltr. 35ppm),
1200x1200dpi Effective output
2. Paper Path: MPF Type Cassette
3. Emulation: PCL6, PS3
4. CPU: SPGPv3
5. Memory: 16~64MB Standard
6. Cassette: 250 sheet Cassette
7. MP: 50 sheet MP
8. Lan: 10/100 Base TX (ML-3471ND)
9. I/O: USB 2.0, IEEE1284
10. Toner: 10K Toner (4K initial)
11. Option: 802.11b/g Wireless N/W,
250 sheet Opt. SCF
ML-347x Series
12. Duplex: Built in Duplex
Contents
1. Precautions
1.1 Safety Warning
1.2 Caution for safety
1.3 ESD Precautions
1-1
1-2
1-4
2. Product spec and feature
2.1 Product Specifications
2.1.1 Product Overview
2.1.2 Specifications
2.1.3 Model Comparison Table
2.1.4 Accessory List
2.2 System Overview
2.2.1 System Construction
2.2.2 Mechanical Parts Specifications
2.2.3 Engine H/W Specifications
2.2.4 S/W Descriptions
2-1
2-1
2-1
2-6
2-6
2-7
2-7
2-12
2-18
2-28
3. Disassembly and Reassembly
3.1 General Precautions on Disassembly
3.2 Screws used in the Printer
3.3 Front Cover
3.4 MP Tray Ass'y
3.5 Rear Cover
3.6 Fuser Ass'y
3.7 Top Cover
3.8 OPE Unit
3.9 Side Cover (Left, Right)
3.10 Shield Controller Ass'y
3-1
3-2
3-4
3-5
3-6
3-7
3-10
3-11
3-12
3-14
Continued
3.11
3.12
3.13
3.14
3.15
3.16
3.17
3.18
3.19
3.20
3.21
3.22
3.23
3.24
3.25
3.26
3.27
Drive Ass'y
Duplex Drive Ass'y
Shield SMPS Ass'y
Connection PCB
Fuser Drive Ass'y
Fan
Pick Up Roller Ass'y
Duplex Guide Housing (With Feed Roller)
HVPS Housing
Cover Mid Front
MPF Housing
Feed Roller Parts
Pick Up Gear Ass'y & Solenoids
Exit Roller
LSU
TERMINAL
Transfer Roller Parts
3-15
3-16
3-17
3-18
3-19
3-20
3-21
3-22
3-23
3-24
3-24
3-25
3-27
3-27
3-28
3-28
3-29
4. Alignment & Troubleshooting
4.1 Alignment and Adjustments
4.1.1 Sample Pattern
4.1.2 Control Panel
4.1.3 Consumables and Replacement Parts
4.1.4 LED Status Error Message
4.1.5 Abnormal Image Printing and Defective Roller
4.1.6 How to use DCU
4.1.7 Paper Jam
4.1.8 Download & Reset F/W
4.2 Troubleshooting
4.2.1 Procedure of Checking the Symptoms
4.2.2 The cause and solution of Bad image
4-1
4-1
4-2
4-7
4-7
4-10
4-11
4-16
4-22
4-23
4-23
4-24
Continued
4.2.3
4.2.4
4.2.5
4.2.6
The cause and solution of the bad discharge
4-40
4-49
The cause and solution of the malfunction
4-59
Toner Cartridge Service
The cause and solutions of bad environment of the software 4-64
5. Exploded Views & Parts List
5.1 Main
5.2 Cover Ass'y
5.3 Front Cover Ass'y
5.4 Rear Cover Ass'y
5.5 OPE Cover Ass'y
5.6 Frame
5.7 MP Ass'y
5.8 Main Drive Ass'y
5.9 Fuser Drive Ass'y
5.10 Duplex Unit (Optional)
5.11 Fuser Unit
5.12 Cassette Unit
5-2
5-4
5-6
5-8
5-9
5-10
5-14
5-16
5-18
5-19
5-21
5-23
6. System Diagram
6.1 Block Diagram
6.1 Connection Dia ram
6-1
6-2
7. Reference Information
7.1 Troubleshooting Tools
7.2 Acronyms and Abbreviations
7.3 Selecting printer locations
7-1
7-2
7-4
Continued
7.4 LAN (Optional Function)
7.5 Sample Tests Patterns
7.6 Series model solution(ML-3470D and ML-3471ND)
7.6.1 Double Feed Erro
7.6.2 Jam0
7.6.3 Jam1
7.6.4 No Paper/Add Paper" error on the printer and have been unable
to clear it, even when they have verified there is paper in the printer
7.6.5 Open Cover Error
7.6.6 Low Toner
7.6.7 Over Heat Error
7.6.8 Low Heat Error
7.6.9 Fuser Door Open
7.6.10 A noise troubleshooting tree
7.6.11 LSU Error
7.6.12 Scan Lock Error
7.6.13 Nothing Displayed on LCD
7.6.14 All black printing
7.6.15 Blank Copy
7.6.16 Images at 1 Copy
7.6.17 Glass Broken
7.6.18 Document Jam
7.7 Parts Life Cycle Maintenance Table
7.7.1 Parts Life Cycle Maintenance Table
7.7.2 Toner Cartridge Criterion
7.8 Model Information
7.8.1 Model List
7.8.2 Understanding for Model Code
7.8.3 Understanding Material Code & Name
7.8.4 F/W Upgrade Method
7-4
7-5
7-6
7-6
7-7
7-8
7-9
7-10
7-11
7-12
7-13
7-14
7-15
7-16
7-17
7-18
7-19
7-20
7-21
7-22
7-23
7-24
7-24
7-24
7-25
7-25
7-25
7-26
7-26
1
Precautions
1. Precautions
The cautions below are items needed to keep in mind when maintaining and servicing.
Please read carefully and keep the contents in mind to prevent accidents while servicing and to prevent the
machine from getting damaged.
1.1 Safety Warning
(1) Request service by qualified service person.
Service for this machine must be performed by a Qualified service person. It is dangerous if unqualified service personnel or users try to fix the machine.
(2) Do not rebuild.
Do not attach or change parts discretionary. Do not dissemble, fix of rebuilt it. If so, printer will abnormally
work and electric shock or fire may occur.
(3) Laser Safety Statement
The Printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J
for Class 1(1) laser products, and elsewhere, is certified as a Class I laser product conforming to the
requirements of IEC 825.
Class I laser products are not considered to be hazardous. The laser system and printer are designed so
there is never any human access to laser radiation above a Class I level during normal operation, user
maintenance, or prescribed service condition.
Warning >> Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. The reflected
beam, although invisible, can damage your eyes. When using this product, these basic safety precautions should
always be followed to reduce risk of fire, electric shock, and injury to persons.
Service Manual
Samsung Electronics
1-1
Precautions
1.2 Caution for safety
1.2.1 Noxious Material Precaution
The toner in a printer cartridge contains a chemical material, which may harm human body if it is swallowed.
Please keep children out of reach of the toner cartridge.
1.2.2 Electric Shock or fire Precaution
It is possible to get electric shock or burn by fire if you don't fallow the instructions of the manual.
(1) Use exact voltage. Please use an exact voltage and wall socket. If not, a fire or an electric leakage can be
caused.
(2) Use authorized power cord. Do use the power cord supplied with PRINTER. A fire can happen when over current flows in the power cord.
(3) Do not insert many cords in an outlet. A fire can be occurred due to flow over current in an outlet.
(4) Do not put water or extraneous matter in the PRINTER. Please do not put water, other liquid, pin, clip, etc. It
can cause a fire, electric shock, or malfunction. If this occurs, turn off the power and remove the power plug
from outlet immediately.
(5) Do not touch the power plug with wet hand. When servicing, remove the power plug from outlet. Do not insert
or take off it with wet hand. Electric shock can be occurr.
(6) Caution when inserting or taking off the power plug. The power plug has to be inserted completely. If not, a fire
can be caused due to poor contact. When taking off the power plug, grip the plug and take it off. If grip the line
and pull over, it could be damaged. A fire or electric shock could happen.
(7) Management of power cord. Do not bend, twist, or bind it and place other materials on it. Do not fix with staples. If the power cord gets damaged, a fire or electric shock can happen. A damaged power cord must be
replaced immediately. Do not repair the damaged part and reuse it. A repaired part with plastic tape can be
cause a fire or electric shock. Do not spread chemicals on the power cord. Do not spread insecticide on the
power cord. A fire or electric shock can be happen due to thinner(weak) cover of the power cord.
(8) Check whether the power outlet and the power plug are damaged, pressed, chopped, or blazing fire or not.
When such inferiorities are found, repair it immediately. Do not make it pressed or chopped when moving the
machine.
(9) Caution when there is thundering or lightning, and being flash of lightening. It causes a fire or electric shock.
Take the power plug off there is thunder. Do not touch cable and device when thundering and flash of lightening.
(10) Avoid the place where is moisture or has dust. Do not install the printer where lots of dust or around humidifier. A fire can occurred. A plug part need to clean well with dried fabric to remove dust. If water drops are
dripped on the place covered with dust, a fire can occurred.
(11) Avoid direct sunlight. Do not install the printer near window where direct contacts to the sunlight. If the
machine contacts sunlight long time, the machine cannot work properly because inner temperature of the
machine is getting hotter. A fire can occur.
(12) Turn off the power and take off the plug when smoke, strange smell, or sound from the machine. If you keep
using it, a fire can be occurred.
(13) Do not insert steel or metal piece inside/outside of the machine. Do not put steel or metal piece into a ventilator. An electric shock could happened.
1-2
Service Manual
Samsung Electronics
Precautions
1.2.3 Handling Precautions
If you ignore this information, you could harm machine and could be damaged.
(1) Do not install it on different levels, or slanted floor.
Please confirm whether it is balanced or not after installation. If it is unbalanced, an accident can be happened due to the machine falling over.
(2) Be careful not to insert a finger or hair in the rotating unit.
Be careful not to insert a finger of hair in the rotating unit (motor, fan, paper feeding part, etc) while the
machine is operating. Once it happens, you could be harmed.
(3) Do not place a pot containing water/chemical or small metals. If they got caught into the inner side of
machine, a fire or electric shock can be occurred.
(4) Do not install it where lots of moisture or dust exists or where raindrop reaches. A fire or electric shock
can be caused.
(5) Do not place a candlelight, burning cigarette, and etc. on the machine. Do not install it near to heater. A
fire can be occurred.
1.2.4 Assembly/Disassembly precaution
When replacing parts, do it very carefully. Memorize the location of each cable before replace parts for reconnecting it afterwards. Do memorize. Please perform the steps below before replace or disassembly the parts.
(1) Check the contents stored in the memory. All the information will be erased after replacing main board.
The information needed to keep has to be written down.
(2) Before servicing or replacing electric parts, take off a plug.
(3) Take off printer cables and power cord connected to printer.
(4) Do use formal parts and same standardized goods when replacing parts.Must check the product name,
part cord, rated voltage, rated current, operating temperature, etc.
(5) Do not give an over-force when release or tighten up the plastic parts.
(6) Be careful not to drop the small parts such as screws in the printer.
(7) Be careful not to change the location of small parts such as screws when assembling and disassembling.
(8) Do remove dust or foreign matters completely to prevent fire of tracking, short, or etc.
(9) After finished repair, check the assembling state whether it is same as before the repair or not.
Service Manual
Samsung Electronics
1-3
Precautions
1.3 ESD Precautions
Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called
“Electrostatically Sensitive (ES) Devices”, or ESDs. Examples of typical ESDs are: integrated circuits, some field
effect transistors, and semiconductor “chip” components.
The techniques outlined below should be followed to help reduce the incidence of component damage caused by
static electricity.
Caution >>Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such
as aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the
assembly.
3. Use only a grounded tip soldering iron to solder or desolder ESDs.
4. Use only an “anti-static” solder removal device. Some solder removal devices not classified as “anti-static” can
generate electrical charges sufficient to damage ESDs.
5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to damage ESDs.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most
replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable conductive material.
7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the
protective material to the chassis or circuit assembly into which the device will be installed.
8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until
completely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing
together of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electricity sufficient to
damage an ESD.
1-4
Service Manual
Samsung Electronics
Product specification and feature
2
2. Product specification and feature
2.1 Product Specifications
2.1.1 Product Overview
Up to 33ppm (Ltr. 35ppm)
ML-3471ND
USB 2.0, IEEE1284
PCL6, PS3, 1200x1200dpi
10K Toner (4K Standard)
400 MHz, 64MB Standard
Built in Duplex
- 250 sheet Cassette
- 50 sheet MP
- 250 sheet Opt. SCF
- 10/100 Base TX
- Opt. 802.11b/g Wireless N/W
2.1.2 Specifications
Product Specifications are subject to change without notice. See below for product specifications.
2.1.2.1 General Print Engine
ML-347x Series
Engine Speed
ML-3470D
ML-3471ND
Simplex
Up to 33 ppm in A4 (35 ppm in Letter)
Duplex
Up to 17 ipm in A4 (17.5 ipm in Letter)
Warmup time
From Sleep
Less than 15 sec, Cold warm-Up time : 15sec
FPOT
From Ready
Less than 8.5 sec
From Idle
Less than 23.5 sec
From Coldboot
Less than 30 sec
-
Up to 1,200 x 1,200 dpi effective output
Resolution
Service Manual
Samsung Electronics
2-1
Product specification and feature
2.1.2.2 Controller & S/W
ML-347x Series
ML-3470D
Processor
Samsung 400 MHz
Memory
ML-3471ND
Std.
32 MB
64 MB
Max.
288 MB
320 MB
Printer Languages
-
PostScript3, PCL6, SPL, IBM ProPrinter, EPSON
Fonts
-
45 scalable, 1 bitmap, 136 PostScript3 fonts
Driver
Default Driver
SPL
Supporting OS
Windows 2000/XP/2003/Vista
Various Linux OS including Red Hat, Caldera, Debian, Mandrake, Slackware,
SuSE and Turbo Linux
Mac OS 8.6~9.2/10.1~10.4
WHQL
Windows XP/2000/2003
Compatibility
PCL6: Win95/98/NT4.0/2000/Me/XP/2003
PS3: Win9x/NT4.0/2000/Me/XP/2003 PPD, Mac PPD, Linux PPD
KS/KSSM: DOS
Protocol
External : SPX/IPX, TCP/IP, SNMP, HTTP 1.1
Supporting OS
Microsoft Windows 98/ME/2000/XP/2003 Microsoft Windows NT 4.xMac OS
8.6 and aboverVarious Linux OS including Red Hat, Caldera, Debian,
Mandrake, Slackware, SuSE and Turbo LinuxNovell 4.x,5.x,6.x
Protocol
External : SPX/IPX, TCP/IP, SNMP, HTTP 1.1
Supporting OS
Microsoft Windows 98/ME/2000/XP/2003 Microsoft Windows NT 4.xMac OS
8.6 and aboverVarious Linux OS including Red Hat, Caldera, Debian,
Mandrake, Slackware, SuSE and Turbo LinuxNovell 4.x,5.x,6.x
RCP
N/A
Status Monitor
N/A
Smart Panel
YES (RCP,SM)
Network Management
SAS (Samsung Admin Service), SetIP
Parallel
-
IEEE 1284
USB
-
USB 2.0
Wired Network
-
N/A
Ethernet 10/100 Base TX (Internal)
Wireless Network
-
N/A
Optional (Internal) 802.11b/g
Wireless LAN (Internal)
LCD
-
2 x 16 Character without backlit
Key
-
8 Key: Stop, Toner Save, Duplex
< , OK, >, Menu, Back
Wired Network
Wireless Network
Application
Interface
User Interface
2-2
Service Manual
Samsung Electronics
Product specification and feature
2.1.2.3 Paper Handling
ML-347x Series
ML-3470D
ML-3471ND
Standard Capacity
-
250-sheet Cassette Tray, 50-sheet Multi Purpose Tray @ 75g/
Max. Capacity
-
550 sheets @ 75g/
Printing
Max. Size
216 x 356 mm (8.5" x 14")
Min. Size
76 x 127 mm (3.0" x 5.0")
Capacity
-
50 sheets @ 75g/
Media sizes
-
A4, A5, A6, Letter, Legal, Folio, Oficio, Executive,ISO B5, JIS B5,
3"x5",Monarch, No.10, DL, C5, C6
Media type
-
Plain Paper, Transparency, Envelope, Labels, Post Card, Card stock
Media weight
-
16~43lb (60 to 163g/ )
Sensing
-
Paper empty sensor
Capacity
-
250 sheets @ 75g/
Media sizes
-
A4, A5, Letter, Legal, Executive, Folio, Oficio, ISO B5, JIS B5
Media types
-
Plain paper, Thick, Thin, Recycled, Archive
Media weight
-
16~28lb (60 to 105g/ )
Sensing
-
Paper empty sensor
Capacity
-
250 sheets @ 75g/
Media sizes
-
A4, A5, Letter, Legal, Executive, Folio, Oficio, ISO B5, JIS B5
Media types
-
Plain paper, Thick, Thin, Recycled, Archive
Media weight
-
16~28lb (60 to 105g/ )
Sensing
-
Paper empty sensor
Face-Down
150 sheets @ 75g/
Face-Up
1 sheet @ 75g/
-
N/A
Supporting
-
Built-in
Media sizes
-
A4, Letter, Legal, Folio, Oficio
Media types
-
Plain Paper
Media weight
-
20~24lb (75 to 90g/ )
Multi-purpose tray
(20lb bond)
Standard Cassette Tray
Optional Cassette Tray
Output Stacking
Capacity
Output Full sensing
Duplex
Service Manual
Samsung Electronics
2-3
Product specification and feature
2.1.2.4 Consumables
ML-347x Series
Toner
Drum
ML-3470D
ML-3471ND
Black
4,000 pages @ ISO 19752 Coverage(Standard 4,000 pages, High Yield
10,000 pages)
Key
Electronic key(CRUM) Only
Life detect
Toner gauge sensor by dot count
Yield
12,000 Images
2.1.2.5 Reliability & Service
ML-347x Series
ML-3470D
ML-3471ND
Printing Volume
(SET AMPV)
-
9,200 sheets-per year / 767 sheets-per month / 38 sheets-per day
5.2 Max. Monthly Duty
-
35,000 sheets
5.3 MPBF
-
100,000 sheets
5.4 MTTR
-
30 min.
5.5 SET Life Cycle
-
250,000 sheets or 5 years (whichever comes first)
5.6 RDS
Comm. Mode
Yes
Operation
Yes
2.1.2.6 Environment
ML-347x Series
Acoustic Noise Level
(Sound Power/Pressure)
Printing
Less than 52.0 dBA
Standby
Less than 26.0 dBA
Sleep
Back Ground Level
Ready
Less than 130W
AVG.
Less than 400W
Max/Peak
Less than 700W
Sleep/Power Off
Less than 11W / Less than 0.4W
Dimension(W x D x H)
SET
400 x 433.4 x 285 mm
Weight
SET
10.5 kg (23.15 Pounds)
Gross
14.5kg (31.9 Pounds)
Power Consumption
2-4
ML-3470D
ML-3471ND
Service Manual
Samsung Electronics
Product specification and feature
2.1.2.7 Options
ML-347x Series
ML-3470D
ML-3471ND
*Memory
-
16 MB, 32 MB, 64 MB, 128 MB, 256MB
Second Cassette
-
250-sheet Cassette Tray
Wired Network
-
N/A
Ethernet 10/100 Base TX
(External) - ML-00ND
Wireless Network
-
N/A
802.11b/g Wireless LAN (Internal)
Hard Disk
-
N/A
Duplex Unit
-
Default
* Memory : The ML-3470D or ML-3471ND has 64MB of memory which can be expanded to 320MB.
Item
Description
Model Code
(order)
Size
Memory DIMM
Exlends your Printers
memory capacity.
ML-00MA
ML-00MB
ML-00MC
ML-00MD
ML-MEM140
16MB
32MB
64MB
128MB
256MB
* Use only the samsung-approved DIMM.
2.1.2.8 Others
ML-347x Series
Memory
Sensor
Service
ML-3470D
Upgradable Mem. Slot
1 EA
Upgradable Mem. Type
100 Pin SDRAM DIMM
Upgradable Mem. Unit
16MB, 32MB, 64MB, 128MB, 256MB
Paper Empty
YES
Paper Size
NO
Media Type
NO
Paper Full
NO
Service Item & Period
1. Transfer Roller : 70K pages
2. Fuser Unit : 80K pages
3. Pick-up Roller : 150K pages
ML-3471ND
Service Manual
Samsung Electronics
2-5
Product specification and feature
2.1.3 Model Comparison Table
SEC
ML-2550
SEC
ML-3050
SEC
ML-3471ND
SAMSUNG
ML-3560
Engine
SEC
SEC
SEC
SEC
Speed(ppm)
24ppm
28ppm
33ppm
33ppm
Processor
266MHz
400MHz
400MHz
400MHz
Resolution
1,200X1,200 dpi
1,200X1,200 dpi
1,200X1,200 dpi
1,200X1,200 dpi
FPOT
12 sec
8.5 sec
8.5 sec
10 sec
Emulation
PS3, PCL6
PCL6
PS3, PCL6
PS3, PCL6
Ram(Std.)
32MB(Max. 160MB)
16MB(Max. 272MB)
64MB(Max. 320MB)
32MB(Max. 288MB)
Interface
IEEE1284, USB 2.0
IEEE1284, USB 2.0
IEEE1284, USB 2.0
IEEE1284, USB 2.0
Duplex
Yes
Factory Option
Yes
Option
Paper Input
(Capa./Type)
550 Cassette, 100 MP
250 Cassette, 50 MP
250 SCF Opt.
250 Cassette, 50 MP
250 SCF Opt.
500 Cassette, 100 MP
500 SCF Option
Os Compatibility
Win 95/98/NT/2000/
Me/XP, Mac
Win 95/98/NT/2000/
Me/XP, Linux
Win 2000/
Me/XP, Linux
Win 95/98/NT/2000/
Me/XP, Linux
Toner
10K
4K/8K
4K/10K
6K/12 K
Image
2.1.4 Accessory List
JC99-02059A [INA-ACCESSORY]
3903-000085 [CBF-POWER CORD]
6801-00761C [CARD-WARRANTY]
6902-000809 [BAG PE]
JC46-00293A [S/W APPLICATION-CD]
JC46-00354A [S/W APPLICATION-CD]
JC68-00761B [MANUAL-REGISTRATION_FROM]
JC68-01579A [MANUAL-NETWORK GUIDE]
JC68-01584A [LABEL(P)-BLANK 90*25]
JC68-00690A [MANUAL-(CARD)WARRANTY CARD]
JC68-00761D [MANUAL-REGISTRATION]
JC68-01344A [MANUAL-WARRANTY CARD]
JC68-01563A [MANUAL-800 SEC CARD]
2-6
Service Manual
Samsung Electronics
Product specification and feature
2.2 System Overview
2.2.1 System Construction
2.2.1.1 SUMMARY
ML-347x Series is consisted of the Engine parts and F/W, and said engine parts is consisted of the mechanical parts
comprising Frame, Feeding, Developing, Driving, Transferring, Fusing, Cabinet and H/W comprising the main control
board, power board, operation panel, PC Interface.
In ML-347x Series, the main controller is consisted of Asic(SPGPv3) parts, Memory parts, Engine Interface parts and it
functions as Bus Control, I/O Handling, drivers & PC Interface by CPU.
Memory Access supports 16bit Operation, and Program Memory 32MB and Working Memory as well.
In ML-347x Series, the paper path is consisted of 250 sheets Cassette containing friction Pad, pickup-roller,
feed-roller for functioning as registration, Earth-transfer for guiding the transfer inlet, Guide-Tr for guiding sheets
between transferring and fixing, Fuser, Exit Assy.
In ML-347x Series, the driving device is consisted of f55 BLDC motor, OPC, Pick-up, Feed, Gear-Train connected with
Mounting member. - to be changed
2.2.1.2 System Layout
Roller-Exit
Roller-Heat
Duplex
Roller-REGI
Roller-MP
OPC
Roller-Transfer
Roller-Pressure
Roller-Feed
Roller-Pickup
Service Manual
Samsung Electronics
2-7
Product specification and feature
2.2.1.2(a) Feeding Section
Feeding Method : Universal Cassette Type
Feeding Standard : Center Loading
Feeding Capacity : Cassette 250 Sheets (75g/ , 20lb StandardPaper)
2.2.1.2(b) Transfer Ass’y
In Warranty( Life time) : Within 70,000 sheets printing
2-8
Service Manual
Samsung Electronics
Product specification and feature
2.2.1.2(c) Driver Ass’y
MAIN Motor ass’y is for Cassette,MPF and Toner Cartridge
EXIT Motor ass’y is for fuser,exit roller and the initial duplexing feeding
Drive Ass'y
Connection
PCB
Duplex Motor
Duplex Drive Ass'y
2.2.1.2(d) Fuser Ass’y
Fusing Type : Lamp Type
Heat Roller : [ 28.3 with 0.1 Crown ]
Pressure Roller Pressure Roller 2 : [electrically conductive]
Thermistor - Temperature Detecting Sensor
Thermostat - Overheat Protection Device
Service Manual
Samsung Electronics
2-9
Product specification and feature
2.2.1.2(e) LSU
LSU is consist of LD(Laser Diode) and polygon motor control. When the controller generate the printing signal LD will
turn on and Polygon motor starts.If the receiving part in LSU detect the beam and then Hsync is generated. When the
rotation of poygon motor is steady, it is time of LSU ready status for printing. If either of two condition is not satisfied,
LSU error is expected.
Trouble
Polygon Motor Error
Hsync Error
Failure Analysis
No steady rotation of Polygon Motor
In spite of steady rotation of Polygon Motor,
There is no generation of the Hsync signal
2.2.1.2(f) Toner Cartridge
OPC Cleaning :Mechanical Cleaning by the cleaning blade.
The recycled toner : Trash room for the recycled toner
No shutter for protecting the OPC Drum
2 Cleaning Roller
VDC = -460V
VPP = 1520V, f = 2.5KHz, Duty(-) = 32%
4
0.16mW
-
-1.25KV
-650V
-50V
+
200V
1
8 Cleaning Blade
3
6
5
+4.2kV
7
2-10
Service Manual
Samsung Electronics
Product specification and feature
2.2.1.2(g) Duplex Unit
Duplex printing function as factory option
Available Paper : Letter, Legal, Folio, Oficio and A4
2.21.2(h) Optional Tray (SCF)
For customer covenience in managing paper
Capacity : 250 sheets
Service Manual
Samsung Electronics
2-11
Product specification and feature
2.2.2 Mechanical Parts Specifications
2.2.2.1 Frame
Material : PC + ABS V0 NH-1000T(Cheil Industries)
Weight : 1.0kg
2.2.2.2 Feeding Part
Feeding Type : Universal Cassette Type
Feeding Standard : Center Loading
Feeding Qty : Cassette 250 sheets (75g/ , 20Ib paper standard)
MPF 50 sheets (75g/ , 20Ib paper standard)
Special Media 5 sheets in MPF (OHP, Envelope, Label, Post Card, Index Paper etc.)
Separating Type : Cassette-Friction Pad Type
MPF-Friction Pad Type
Driver Type : Driving by Gearing from Main Motor
Pick Up Roller Driver : Solenoid
Pick Up Roller Rubber Material : EPDM + IR = 1.6 or more
Paper detecting Sensor : Photo Sensor
Paper Size Sensor : None
Paper Separating Pad Material : NBB 52 = 0.8~1.2
Separating Pad Pressure : 190gf
Feeding Pressure (Cassette) : 250 gf 10% (SPRING H mm, based on 1 sheet)
320 gf 10% (SPRING H mm, based on 250 sheet)
Paper Exit Type : Face Down
Feed Roller Driver : Solenoid
2.2.2.3 Transfer Ass’y
It is consisted of PTL(pre-transfer lamp) and Transfer Roller. The PTL sends a light to the OPC drum, makes the current
on the drum surface to low, and improve the transfer efficiency.
The transfer roller delivers the toner of the OPC drum to the paper.
TR Voltage : +1.3KV 5% (based on 200 , in accordance with media area, Transfer table)
-1.20KV 10% (In cleaning)
Transfer Trigger Current : 6.5
5%
Transfer Efficiency : 85% or more (All envirmnment : preferable media)
Voltage System : Voltage PWM Control System
Transfer Roller
- Material : NBR FOAM ROLL
- Structure : Mono layer
- Resistance : 3E +07 ~ 8E +07 (N/N)
- Hardness : 40
3% (ASKER-C)
- Validlength : 224.2 +0.5/-0mm
- OD : 15.0 0.5mm
- SHAFT Material : SUM -24L + Non-electrolysis Ni. Coating
Life Span : Print over 70,000 sheets (in 15~30 )
2-12
Service Manual
Samsung Electronics
Product specification and feature
2.2.2.4 Driver Ass’y
2.2.2.4(a) Motor
Spec : BLDC 62 + PM 55 Motor (2-2 Bipolar) + PM 42 Motor (2-2 Bipolar)
Pull-Out Torque:
BLDC 62 : 1500 gf.cm(based on actual value) or more (1342.4rpm, 1.8A)
PM 55 : 1490gf.cm(based on actual value) or more (711pps, 0.9A)
PM 42 : 240gf.cm(based on actual value) or more (1850pps, 0.6A)
TORQUE MARGIN (Tp/o Tsys) : BLDC 62 Motor : 1500/1100 gf.cm=1.36
PM 55 Motor : 1490/1053 gf.cm = 1.41
PM 42 Motor: 240/165 gf.cm = 1.45
Driving Frequency: BLDC 62 Motor : 1342.4 rpm(1006.8 Clock)
PM 55 Motor : 888.75 rpm(711 pps)
PM 42 Motor : 1156 .25rpm(1850 pps)
It is a power delivery unit by gearing: BLDC 62 Motor -> Pickup/Feeder/Developer
PM 55 Motor -> Fuser/Exit
PM 42 Motor -> Duplex
2.2.2.4(b) Process Speed
Print Speed : 33/35 PPM (based on A4/LTR )
Process Speed : 211.78 mm/sec
Jitter
Vertical : 3 0.018 or less in Vision System
Horizontal : within 2% of partial magnificence error
Orthogonality : SPEC :
1.0 mm or less
2.2.2.4(c) Acoustic Noise
Warming Up : 43dB or less
Printing : 52dB or less
Stand-by : 26dB or less
Service Manual
Samsung Electronics
2-13
Product specification and feature
2.2.2.5 Fixing Part (Fuser)
The fuser is consisted of the E-Coil, Heat Roller, Pressure Roller, Thermistor and Themostat.
It adheres the toner to the paper with pressure and a heat to complete the printing job.
2.2.2.5(a) Halogen Lamp
Voltage 120V : 115 5%
220V : 230 5%
Capacity : 800 Watt 25W
Temp. Distribution : 120%
2.2.2.5(b) Temperature-Interception Device (Thermostat)
Thermostat Type : Non-Contact type THERMOSTAT
Control Temperature : 170
5
THERMOSTAT-ROLLER Gap : 1.6 0.2mm
2.2.2.5(c) Temperature Detecting Sensor(Thermistor)
Thermistor Type : HF-R0060 (SEMITEC 364FL Type)
Temperature Resistance : 7 (180 )
SYSTEM Temperature SETTING
- Stand by : 165 5
- Printing : 189 5 (5 minutes before)
184 5 (5 minutes after)
- Overshoot : 200 less
- Overheat : 210 less
2.2.2.5(d) Heat Roller
Length : 247.5mm
Valid length : 224mm
OD : 28.3 + 0.05, -0.03 (Tubing incl., Crown 0.09~-0.15)
Material : AL(AL5052) + PFA Tubing
Thickness : 0.9mm
Coating Material : PFA 100%
Coating Thickness : 20um (Thickness after abrasion)
GND Type : H/R Bearing Grounding type By SECC Fuser lower frame
2-14
Service Manual
Samsung Electronics
Product specification and feature
2.2.2.5(e) Pressure Roller
Shaft
- Length : 251.3mm
- Material : SUM
- Thickness : 6( 14 - RUBBER portion)
Rubber 1
- Material : Silicon Rubber (Tubing Type :
- Length : 226.4mm
- Thickness : 5mm(one-side)
Rubber 2
- Material : Silicon Rubber (Tubing Type :
- Length : 226.4mm
- Thickness : 5mm(one-side)
OD : 1) 20
2) 16
20)
16)
0.2(Center part Crown -0.2)
0.2(Center part Crown -0.15)
2.2.2.5(f) Media Separating System
PI Coating with PPS Claw System
2.2.2.5(g) Safety Relevant Facts
Proteciong device when overheating
- 1st protecting device : H/W cuts off when detecting an overheating
- 2st protecting device : S/W cuts off when detecting overheating
- 3st protecting device : Thermostat cuts off the power
Safety device
- The power of Fuser is cut-off after front cover is open
- The overheating safety device for customer
- The surface temperature of the Fuser Cover is under 80
Service Manual
Samsung Electronics
2-15
Product specification and feature
2.2.2.6 LSU (Laser Scanner Unit)
The LSU unit is controlled by video controller. It scans the video data received from video controller with laser beam by
using the rotation principle of the polygon mirror to create the latent image on the OPC drum. It is the core part of LBP.
The OPC drum rotates as the same speed as the paper feeding speed. It creates the /HSYNC signal and sends it to the
engine when the laser beam of the LSU reaches the end of the polygon mirror, and the engine detects the /HSYNC signal
to arrange the vertical line of the image on the paper. After detecting the /HSYNC signal, the image data is sent to the
LSU to arrange the its margin on the paper.
The one side of the polygon mirror is one line for scanning.
2.2.2.7 Toner Cartridge
In the toner cartridge, the OPC unit and the developer unit are in a body.
The OPC unit has OPC drum and charging roller, and the developer unit has toner, toner cartridge, supply roller,
developing roller, and the blade.
2.2.2.7(a) Summary
Developing Method : Non magnetic 1 element contacting method
Toner : Non magnetic 1 element shatter type toner
Charging capacity : -39.1
Average OD : 8.5
0.5
3
C/g (KAO meas. method)
(Toner)
Toner Qty : 125 gf/250gf (4k / 10k)
The life span of toner: 4k/10k sheets (ISO 19752 Pattern / A4 standard )
Toner Residual Sensor : Dot count with CRUM(CRU Monitor)
OPC Cleaning : Collect the toner by using cleaning blade+ FILM OPC
Handling of wasted toner : Collect the wasted toner in the cleaning frame by using cleaning blade
OPC Drum Protecting Shutter : None
Classifying device for toner cartridge: ID is classified by interruption of the frame channel.
2.2.2.7(b) Developing Roller
Roller type : conductive elastic roller
Rotary Speed : 203.06 mm/sec
Roller Bias : -220V ~ -400
20V
Control Type : Bias PWM Control type
Roller material : Conductive NBR + Surface UV process
- Structure : Mono layer
- Resistance : 1.0E+03~ 1.5E+06
(N/N Condition)
- Hardness : 52 5
- Valid Length : 228 mm
- OD : 14.07 mm 0.05
- Shaft material : SUS 303
- Surface roughness (Ra) : Ra 2.0 ~ 2.5 (Circular-direction)
- Friction coefficient (u) : 0.1 ~ 0.5 (70gf, 50mm/min, OHP (3M,#CG3300))
- Life : 10,000 sheets or more
2-16
Service Manual
Samsung Electronics
Product specification and feature
2.2.2.7(c) Supply Roller
Rotary Speed : 131.98 mm/sec
Roller Bias : -370V ~ -550V
Control Type : Bias
Roller material : Nylon Fur
- Structure : Closed cell
- Resistance : 0.6E+05 ~ 3.0E+06
(N/N cond.)
- Hardness : 16 ~ 25 (Asker "C")
- Valid Length : 218 mm
- OD : 11.2 0.1 mm
- Shaft material : SUM 24L Non-electrolysis Ni. Coating
- Shaft OD : 8.2 mm + 0 / -0.05
- Driver : Gear Driver (in a direction opposed to D/R)
- Sponge Density : 0.45 , 0.1 g/
- Life : 10,000 sheets or more
2.2.2.7(d) REGULATING BLADE
Type : Regulating toner layer by pressure
Material : SUS 301 1/2H CSP t0.08
Valid Length : 228mm
Voltage : -420V ~ -600V
Regulating edge R value : 0.3
0.02mm
Pressure : 42 gf/cm
2.2.2.7(e) CHARGING PORTION
Type : Conductive Roller Contact-Charge
Rotary Velocity : 179.7 mm/sec
Surface potential : -760
70V (based on OPC , N/N cond.)
Residual potential : -130 V or less (initial)
Control Type : Bias PWM Control
Roller material : Conductive elastic roller (Conductive NBR + SBR)
- Structure : Mono layer (Surface UV process)
- Resistance : 0.75E+06 ~ 5.0E+06 ( N/N cond.)
- Hardness : 50 3 (Asker "A")
- Length : 230 mm
- OD : 12.0 0.05 mm
- Shaft Material : SUM-24L + Non-electrolysis Ni Coating
- Shaft OD : 6 + 0 / -0.05 mm
- Driver : Gear Driver
- Pressure : L:300 gf / R:350 gf
- Roller surface roughness : Ra 1.8 um or less (shaft direction)
- Roller life : 10,000 sheets or more
Roller Voltage : -1.25 ~ -1.70 KV
Service Manual
Samsung Electronics
2-17
Product specification and feature
2.2.3 Engine H/W Specifications
2.2.3.1 ML-347x (PCL) Main Board
The Engine Board and the Controller Board are in one united board, and it is consisted of CPU part and print part in
functional aspect. The CPU is functioned as the bus control, I/O handling, drivers, and PC interface. The main board
sends the Current Image of Video data to the LSU and manages the conduct of Electrophotography for printing. It is
consisted of the circuits of the motor (paper feed, pass) driving, clutch driving, pre-transfer lamp driving, current driving,
and fan driving.
The signals from the paper feed jam sensor and paper empty sensor are directly inputted to the main board.
2.2.3.1(a) Asic(SPGPv3)
CPU Core : ARM1020E
- 32KB instruction cache and 32KB data cache
Operating Frequency
- CPU Core : over 300MHz
- System Bus : 100MHz
SDRAMC
- 32Bits Only, 100MHz
- 5 Banks (Up to 128MB per Bank)
ROMC
- 4 Banks (Up to 16MB per Bank)
IOC
- 6 Banks (Up to 16MB per Bank
DMAC
- 4 Channels
HPVC
- Dual/Single Beam
- LVDS Pad(VDO, HSYNC)
UART
- 5 Channels (1 Channels Supports DMA Operation)
PCI Controller
- 32Bits, 33/66MHz
- PCI Local Bus Specification rev2.2 Complaint
- Host / Agent Mode (Support 4 Devices in Host Mode)
NAND Flash Controller
- 8/16Bits, H/W EEC Generation
- Auto Boot Mode (Using Internal SRAM, 4KB)
MAC
- 10M/100Mbps
- Full IEEE 802.3 Compatibility
Engine Controller
- LSU Interface Unit
- Step Motor : 2 Channels
- PWM : 8 Channels
- ADC : 6 Channels
I2C Controller
- I2C(S-BUS) Slave Device Support(I2C Version 2.1)
RTC
- RTC Core Voltage : 3V
PLL
- 3 PLL : MAIN, PCI, PVC
2-18
Service Manual
Samsung Electronics
Product specification and feature
2.2.3.1(b) Memory
Flash Memory : It stores System Program and downloads the System Program through PC Interface, and in case of
model for export it compresses the PCL font, then stores it.
- Capacity : 32M Byte (NAND Flash)
- Random Access Time : 10 us (Max)
- Serial Page Access Time : 50ns (Min)
DRAM : It is used as Swath Buffer, System Working Memory Area, etc. when printing.
It stores Font List, compressed into Flash memory, on DRAM and uses it as PCL font in case of model for export.
- Capacity : 64M Byte(Basic), up to 320Mbyte (User Option)
- Type : SDRAM 100MHz/133MHz , 16bit
2.2.3.1(c) Others
The Option PBA can be mounted for supporting the serial communication.
Main board
Flash ROM
PHY IC
USB IC
SDRAM
SPGPv3
(ASIC)
SRAM
Service Manual
Samsung Electronics
2-19
Product specification and feature
2.2.3.1(d) Flash Memory
It stores the system program and downloads system program through the PC Interface.
Capacity : 16M Byte (NOR Flash)
Access Time : 90ns
Page read Time : 25ns
2.2.3.1(e) SDRAM
It is used as swath buffer, system working memory area, etc. while Printing.
Capacity : The 64M Bytes is for this model (64M : Printing System Working Memory Area)
2.2.3.1(f) Sensor Input Circuit
Paper Empty Sensing
The Paper empty sensor (Photo Interrupter) on the HVPS informs the state of paper to CPU whether it is empty or not
with operation of the actuator.
When cassette is empty, it detects the fact by reading the E20 of CPU, and then informs the fact by displaying the RED.
MP Sensing
By operation of Actuator on the frame, an individual MP Sensor (Photo interrupter) informs the state of paper to CPU
whether it is empty or not. It reads the D17 of CPU for recognizing paper in MP, and paper is fed from MP if there is.
Paper Feeding/With Toner Cartridge Sensing
When paper passes the actuator (feed sensor part), it detects the signal of Photo interrupter, informs the paper feeding
state to CPU, and then sprays the image data after certain time.
If it doesn t detect the feed sensor within 1sec. after paper is fed, paper Jam0 is occurred (LED will be display RED
color). The fact whether the developer is inserted or not is detected by CRUM. After the developer is mounted, the subCRUM can read the information of toner cartridge from contact with CRUM involved in toner cartridge. If the information of
toner cartridge is invalid, it will show invalid sign on a LCD or LED.
Paper Exit Sensing
It detects paper state whether paper gets out from the set with operation of exit sensor on the HVPS and actuator on the
frame. Paper detects the on/off time of exit sensor by reading D22 of CPU, and the normal operation or jam information is
informed to the CPU.
The paper JAM2 is informed. (LED will be display RED color)
Cover Open Sensing
The Cover open sensor is located on the HVPS. After the front cover is opened, +24VS (DC fan, Solenoid, Main Motor,
Polygon motor part of LSU and HVPS), which is supplied to the each unit, is cut off. The cover-open sensing is operated
by the D23 of CPU.
In case, the red will be ON for informing the facts to user.
2-20
Service Manual
Samsung Electronics
Product specification and feature
DC FAN / SOLENOID Driving
It is driven by transistor and controlled by D14(FAN MAIN), E16(FAN DUPLEX), C23(PICK-UP CLUTCH), C18(REGI
CLUTCH), D15(MPF CLUTCH) of CPU.
When it is high, the fan is driving by turning on the TR, and it is off when the sleep mode is selected. There are three
solenoids, and they are driven by paper pick-up, regi and MPF signal. It is turned on or off by C23, C18, D15 of CPU. The
diode protects the driving TR from the noise pulse, which is flown when the solenoid id de-energizing.
FAN Driving Circuit is driven by Transistor, and controlled by D14, E16 of CPU.
Motor Driving
The main motor driving circuits is on the BLDC Motor Ass y Unit. Main Controller has the interfacing circuits. There is
motor driver IC on the motor control board of Motor Ass y Unit.
The exit motor driving circuits is formed when the driver IC is selected. The AN44060A Motor Driver IC is used in this
case. The resistance Rs value for sensing and voltage value for the V reference can be changed by motor driving voltage
value. The motor driving voltage is calculated with the following formula.
IN 0, 2
L
H
L
H
IN 1, 3
L
L
H
H
Output Current
Vref / (10*Rs) = Iout
Vref / (15*Rs) = Iout * 2/3
Vref / (30*Rs) = Iout * 1/3
0
The motor driving circuit is formed when the Driver IC is selected. The A3977 Motor Driver IC is used in this case. The
resistance Rs value for sensing and voltage value for the V reference can be changed by motor driving voltage value. The
motor driving voltage is calculated with the following formula.
I = Vref / Rs, wherein Vref is (R1 5V) / (R1+R2).
Service Manual
Samsung Electronics
2-21
Product specification and feature
2.2.3.2 SMPS & HVPS board
The SMPS supplies DC Power to the System.
It takes 110V/220V and outputs the +5V, +24V to supply the power to the main board. The HVPS board creates the high
voltage of THV/MHV/Supply/Dev and supplies it to the developer part for making best condition to display the image. The
HVPS part takes the 24V and outputs the high voltage for THV/MHV/BIAS, and the outputted high voltage is supplied to
the toner, OPC cartridge, and transfer roller.
2.2.3.2(a) HVPS (High Voltage Power Supply)
Transfer High Voltage (THV+)
- Input Voltage : 24 V DC 15%
- Output Voltage : MAX +5.0KV 5 %,(Duty Variable, no loading )
->1.2KV 15% (when cleaning,200 )
- Output Voltage Trigger : 6.5
- Input contrast of the Voltage stability degree :under 5 % (fluctuating input 21.6V 26.4V)
Loading contrast : 5 % or less
- Output Voltage Rising Time : 100 ms Max
- Output Voltage Falling Time : 100 ms Max
- Fluctuating transfer voltage with environmental various : +650 V(Duty 10%) ~ 5 KV (Duty 90%)
- Environment Recognition Control Method : The THV-PWM ACTIVE is transfer active signal. It detects the resistance
by recognizing the voltage value, F/B, while permits the environmental recognition voltage.
- Output Voltage Control Method : Transfer Output Voltage is outputted and controlled by changing Duty of THVPWM
Signal. 10% Duty : +650V, 90% Duty : +5KV 5%
Charge Voltage (MHV)
- Input Voltage : 24 V DC 15%
- Output Voltage : -1.3KV ~ -1.8KV DC 50V
- Output Voltage Rising Time : 50 ms Max
- Output Voltage Falling Time : 50 ms Max
- Output Loading range : 30 M ~ 1000 M
- Output Control Signal(MHV-PWM) : CPU is HV output when PWM is Low
Cleaning Voltage (THV-)
- The (+) Transfer Voltage is not outputted because the THV PWM is controlled with high.
- The (-) Transfer Voltage is outputted because the THV-Enable Signal is controlled with low
- The output fluctuation range is big because there is no Feedback control.
Developing Voltage (DEV)
- Input Voltage : 24 V DC 15%
- Output Voltage: -200V ~ -600V DC 20 V
- Output Voltage Fluctuation range: PWM Control
- Input contrast of the output stability degree : 5 % or less
Loading contrast : 5 % or less
- Output Voltage Rising Time : 50 ms Max
- Output Voltage Falling Time : 50 ms Max
- Output Loading range : 10M ~ 1000 M
- Output Control Signal (BIAS-PWM) : the CPU output is HV output when PWM is low.
Supply
- Output Voltage : -400 V ~ -800V DC 50 V(ZENER using, DEV )
- Input contrast of the output stability degree : under 5 %
Loading contrast : 5 % or less
- Output Voltage Rising Time : 50 ms Max
- Output Voltage Falling Time : 50 ms Max
- Output Loading range : 10 M ~ 1000 M
- Output Control Signal (BIAS-PWM) : the CPU is HV output when PWM is low.
2-22
Service Manual
Samsung Electronics
Product specification and feature
HVPS PBA
SUPPLY
-630 3%
DEV
-430 3%
THV
+1300 3%
-1200 3%
OPC
-130 15.4%
MHV
-1350¡ 3%
2.2.3.2(b) SMPS (Switching Mode Power Supply)
It is the power source of entire system. It is assembled by an independent module, so it is possible to use for common
use. It is mounted at the side of the set.
It is consisted of the SMPS part, which supplies the DC power for driving the system, and the AC heater control part,
which supplies the power to fuser. SMPS has two output channels. Which are +5V and +24V.
AC Input
- Input Rated Voltage : AC 220V ~ 240V AC 110V ~ 127V
- Input Voltage fluctuating range : AC 198V ~ 264V AC 99V ~ 135V
- Rated Frequency : 50/60 Hz
- Frequency Fluctuating range : 47 ~ 63 Hz
- Input Current : Under 4.0Arms / 2.0Arms (But, the status when e-coil is off or rated voltage is inputted/outputted )
Service Manual
Samsung Electronics
2-23
Product specification and feature
NO
ITEM
CH1
CH2
Remark
1
CHANNEL NAME
+5V
+24.0V
2
CONNECTOR PIN
CON 35V PIN: 11,13,15
GND PIN: 12,14,16
CON 324V PIN:3,5,7,9
GND PIN:4,6,8,10
3
Rated Output
+5V 5%(4.75 5.25V)
+24V 10%(21.6 26.4V)
4
Max. Output Current
3A
4.4 A
5
Peak Loading Current
3.6 A
5.3 A
6
RIPPLE NOISEVoltage
100mVp-p
Under 500mVp-p
7
Maximum output
15W
105.6W
8
Peak output
18W
127.2W
9
Protection for loading
shortage and
overflowing current
Shut down or Fuse
Protection
Shut down or Output
Voltage Drop
NO
ITEM
System
1
Stand-By
Less than 130W
2
PRINTING
Less than 400W
3
Sleep-Mode
Less than 11W
1ms
1ms
Fuse 24V
Fuse 5V
Fuse 5V
2-24
Service Manual
Samsung Electronics
Product specification and feature
Length of Power Cord : 1830 50mm
Power Switch : Use
Feature
- Insulating Resistance : 100 or more (at DC 500V)
- Withstanding Voltage : Must be no problem within 1 min.
(at 1000V-LV model / 1500Vac-HV model,10mA)
- Leaking Current : under 3.5mA
- Running Current : under 40A PEAK (AT 25 , COLD START)
under 60A PEAK (In other conditions)
- Rising Time : within 2Sec
- Falling Time : over 20ms
- Surge : Bi-Wave 3kV - Normal, 6KV - Common
Environment Condition
- Operating temperature range : 0
40
- Maintaining temperature range : -25
85
- Preserving Humidity Condition : 30% 90% RH
- Operating atmospheric pressure range : 1atm
EMI Requirement : CISPR ,FCC, CE, MIC, C-Tick,
Safty Requrement :IEC950 UL1950, CSA950, C-UL,NOM, TUV, Semko, Nemko, iK, CB, CCC(CCIB), GOST, EPA,
Power Save
2.2.3.2(c) FUSER AC POWER CONTROL
Fuser(e-coil) gets heat from AC power. The AV power controls the switch with the Triac, a semiconductor switch. The
ON/OFF control is operated when the gate of the Triac is turned on/off by Phototriac (insulting part).
In other words, the AC control part is passive circuit, so it turns the heater on/off with taking signal from engine control
part.
When the HEATER ON signal is turned on at engine, the LED of PC501 (Photo Triac) takes the voltage and flashes.
From the flashing light, the Triac part (light receiving part) takes the voltage, and the voltage is supplied to the gate of
Triac and flows into the Triac. As a result, the AC current flows in the e-coil, and heat is occurred.
On the other hand, when the signal is off, the PC501 is off, the voltage is cut off at the gate of Triac, the Triac becomes
off, and then the e-coil is turned off.
Triac (Q501) feature : 24A-LV model / 16A-HV model, 600V SWITCHING
Phototriac Coupler (PC501)
- Turn On If Current : 15mA 50mA(Design: 16mA)
- High Repetive Peak Off State Voltage : Min 600V
Service Manual
Samsung Electronics
2-25
Product specification and feature
2.2.3.3 Engine F/W
2.2.3.3(a) Control Algorithm
Feeding
If feeding from a cassette, the drive of the pickup roller is controlled by controlling the solenoid. The on/off of the solenoid
is controlled by controlling the general output port or the external output port. While paper moves, occurrence of Jam is
judged as below.
ITEM
Description
JAM 0
- After picking up, paper cannot be entered due to paper is not fed.
- After picking up, paper entered but it cannot reach to the feed sensor in certain time due to slip, etc.
- After picking up, if the feed sensor is not on, re-pick up. After re-picking up, if the feed sensor is not on
after certain time, it is JAM 0.
*It is a status that the leading edge of the paper doesn t pass the feed sensor.
-Even though the paper reaches to the feed sensor, the feed sensor doesn t be ON.
*It is a status that the leading edge of the paper already passes the feed sensor.
JAM 1
- After the leading edge of the paper passes the feed sensor, the trailing edge of the paper cannot pass
the feed sensor after a certain time. (The feed sensor cannot be OFF)
- After the leading edge of the paper passes the feed sensor, the paper cannot reach the exit sensor after
certain time. (The exit sensor cannot be ON)
*The paper exists between the feed sensor and the exit sensor.
JAM 2
- After the trailing edge of the paper passes the feed sensor, the paper cannot pass the exit sensor after
certain time.
Transfer
The charging voltage, developing voltage and the transfer voltage are controlled by PWM (Pulse Width Modulation). The
each output voltage is changeable due to the PWM duty. The transfer voltage admitted when the paper passes the
transfer roller is decided by environment recognition. The resistance value of the transfer roller is changed due to the
surrounding environment or the environment of the set, and the voltage value, which changes due to the environments, is
changed through AD converter. The voltage value for impressing to the transfer roller is decided by the changed value.
Each voltage value is controlled according to 3.3.3.2 Timing Chart.
Fusing
The temperature change of the heat roller s surface is changed to the resistance value through the thermistor. By
converting the voltage value, which impressed to the resistance, to the digital value through the AD converter, the
temperature is decided. The AC power is controller by comparing the target temperature to the value from the thermistor.
If the value from the thermistor is out of controlling range while controlling the fusing, the error stated in the below table
occurs.
2-26
Service Manual
Samsung Electronics
Product specification and feature
Open Heat Error
When the engine operates the warm-up process, if the temperature of the fixing unit is not higher than a specified
temperature, the engine defines Open Heat Error. When this error is broken out, the engine stops all functions and keeps
the error state. Also, the engine informs the error status of the main system. And then the error message is displayed at
LCD window or LED informing the error status of the user.
Low Heat Error
When the engine is at stand-by, printing or warm-up mode, if the temperature of the fixing unit is lower than the specified
temperature at each state and the lower temperature state is maintained during the specified time, the engine defines
Low Heat Error. When this error is broken out, the engine stops all functions and keeps it at the error state. Also the
engine informs the error status of the main system. And then the error message is displayed at LCD window or LED
informing the error status of the user.
Over Heat Error
For overall engine state, if the temperature of the fixing unit is higher than the specified temperature and the temperature
state is kept during the specified time, the engine defines Over Heat Error. When this error is broken out, the engine stops
all functions and keeps it at the error state. Also, the engine informs the error status of the main system. And then the
error message is displayed at LCD window or LED to inform the error status of the user.
* To recover the heat error: The heat error recovery is operated automatically when the error is only caused by Low Heat
Error, not the Heat Errors in Warm-up state and the Over Heat Error. If an error happens, then the engine memorizes a
present temperature. In case of Low Heat Error, the maximum heat is supplied to the fixing unit. When a specified time
is elapsed, the engine detects the temperature again. If the present temperature is higher than the memorized
temperature, the error is recovered. In case of Over Heat Error, no heat is supplied to the fixing unit. When a specified
time is elapsed, the engine detects a present temperature again. If the present temperature is a specified degree lower
than the memorized temperature, the error is recovered.
LSU
LSU receives the image data from PVC or HPVC and make the latent image on OPC surface.
It uses the dual beam, LD1 and LD2. But the control method of them is the same.
Just in comparison with the single beam, the dual beam has the half of lsu s frequency.
->The frequency of the dual beam = the frequency of the single beam /2.
The errors related to LSU are as follows:
* By LReady: When the printing is started, the engine drives the polygon motor of LSU. After the specified time is elapsed,
if the motor is not in a ready status, the engine detects the error that the polygon motor is not in a ready status. If this
error happens, the engine stops all functions and keeps it at the error state. Also, the engine informs the error status of
the main system and the error message is displayed at LCD window to inform the error status of the user.
* By Hsync: When the polygon motor is ready, the LSU sends out the signal called Hsync and used to synchronize with
each image line. So, if the engine does not detect consecutively the signal for a fixed time, it defines the Hsync Error. If
this error happens, the engine stops all functions and keeps it at the error state. Also, the engine informs the error status
of the main system and then the error message is displayed at LCD window to inform the error status of the user.
LSU Error Recovery: If the LReady or Hsync error happens, the paper exits out beforehand. The engine mode is
changed to recovery mode and the engine informs the main system of the engine mode. And the engine checks the LSU
error. If the error doesn t happen, the printing job will be proceeding.
Service Manual
Samsung Electronics
2-27
Product specification and feature
2.2.4 S/W Descriptions
2.2.4.1 Overview
The software of Cygnus system is constructed with
1) Host Software part that the application software operated in Window and Web Environment, and
2) Firmware parts that is a Embedded software controls printing job.
2.2.4.2 Architecture
Host Software is made up of
1. Graphic User Interface that offers the various editing functions to user in Host,
2. Driver that translates the received document to a Printing Command language which printer can understand and
transfers data to spooler,
3. Stand-alone Application that offers the various printing application, DMS(Document Management System),
RCP(Remote Control Panel), Printer Status Monitor, Network Management in Window system,
4. Web-based-Application that offers the same functions as Stand-alone Application and RDC(Remote Diagnosis
Control) in Web environment.
Firmware is made up of
1. Application (Emulation) that is a interpreter translate data received from Host to a printing language (PCL, PS, GDI,
etc.) to be able to make the user to take same output as originally one what composed in Host.
2. Kernel that control and management the whole procedure include of Control flow and Printing Job before transfer to
Engine system.
2-28
Service Manual
Samsung Electronics
Product specification and feature
2.2.4.3 Data and Control Flow
The above Block Diagram is explained that:
Host Side is made up of
1. Driver that is Windows application software translate printed data to one of printer language and create spooler file,
2. Web-based Application that offer a various printer additional functions, management of printing job, printer
administration, Status monitor to monitoring the printer status by real time in Web, independent environment on OS.
3. Stand-alone Application that is a similar Window software as same as above 2,
4. Port Monitor that manages the network communication between spooler and Network Interface Card, or various
additional application and Network Interface Card,(this is, at first, make communication logical port, manage the data,
transfer them from spooler to network port, and offer the result of printing).
Service Manual
Samsung Electronics
2-29
Product specification and feature
Firmware Side is made up of
1. Network Interface Card is that relay the communication between Host and kernel using various network protocol,
2. Kernel is that manages the flow control of emulation procedure, receiving data from Host or Network card and printing
with engine & rendering job,
3. Emulation is that interprets the various output data from selected emulation,
4. Engine is that prints rendered bit-map data to paper with required size and type by Kernel.
And then, for Job Spooling function for Multi-User, Multi-Printing that is occurred in Network printing and various additional
printing functions, this Kernel use max. 10 Queuing systems in a memory.
In Printing, the two procedures are
(1) Case of using Parallel or USB Port
After user start to print the wanted document to PCL string or compressed GDI bit-map data, Driver translate the all
graphic data of it and send data to host spooler. And then the spooler sends the data stream to the printer via
parallel port or USB port.
Kernel receives this data from Host, and then select emulation fit to data and start selected one. After emulation job
end, Kernel sends the output bit-map data to Engine using Printer Video Controller (by clock type for LSU).
Engine print the received data to required paper with the sequential developing process.
(2) Case of using Network Interface Card
After user start to print the wanted document to PCL string or compressed GDI bit-map data, Driver translate the all
graphic data of it and send data to host spooler.
If so, Port monitor managing network port receives data from spooler and sends a data stream to the Network
Interface Card.
Network interface card receives it and send to Kernel part,
Kernel receives this data from Host, and then select emulation fit to data and start selected one. After emulation job
end, Kernel sends the output bit-map data to Engine using Printer Video Controller (by clock type for LSU).
Engine print the received data to required paper with the sequential developing process.
The additional printing function are realized in
(1) Web environment
(2) Window environment.
On addition, Kernel informs a status of printing status and printer status to user made printing job with the Status Monitor.
2-30
Service Manual
Samsung Electronics
3
Disassembly and Reassembly
3. Disassembly and Reassembly
3.1 General Precautions on Disassembly
When you disassemble and reassemble components, you must use extreme caution. The close proximity of cables
to moving parts makes proper routing a must.
If components are removed, any cables disturbed by the procedure must be restored as close as possible to their
original positions. Before removing any component from the machine, note the cable routing that will be affected.
Whenever servicing the machine, you
must perform as follows:
1. Check to verify that documents are not stored in
memory.
Releasing Plastic Latches
Many of the parts are held in place with plastic latches.
The latches break easily; release them carefully.
To remove such parts, press the hook end of the latch
away from the part to which it is latched.
2. Be sure to remove the toner cartridge before you
disassemble parts.
3. Unplug the power cord.
4. Use a flat and clean surface.
5. Replace only with authorized components.
6. Do not force plastic-material components.
7. Make sure all components are in their proper position.
Service Manual
Samsung Electronics
3-1
Disassembly and Reassembly
3.2 Screws used in the Printer
S1(BH Short)
S2(PH Long)
6001-000568
S3(WH Long)
6002-000440
S4(WH Long)
3-2
6001-000130
6003-000196
SHIELD+PARRALLEL PORT
COVER MIDDLE+FRAME BASE
SCREW-MACHINE;BH,+,M3,L6,ZPC(WHT),SWRCH18A,-,-
3
SCREW-MACHINE;BH,+,M3,L6,ZPC(WHT),SWRCH18A,-,-
2
SCREW-MACHINE;PH,+,M3,L8,NI PLT,SWRCH18A,FP,-
2
SCREW-TAPPING;PWH,+,-,2,M3,L8,ZPC(BLK),SWRCH18A,-
4
SCREW-TAPPING;PWH,+,-,2,M3,L8,ZPC(BLK),SWRCH18A,-
1
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
6
COVER REAR
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
4
COVER SIDE L
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
1
COVER SIDE R
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
1
COVER TOP
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
4
DUP DRIVE ASS'Y+FRAME BASE
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
3
DUP FAN+FRAME BASE
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
1
MAIN DRIVE ASS'Y+FRAME BASE
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
6
SHIELD CONTROLLER+FRAME BASE
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
3
SHIELD SMPS+FRAME BASE
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
3
Frame Base+Fuser
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
4
frame assy
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
33
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
1
FRAME MP+BRACKET FEED
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
2
FRAME MP+HOLDER IDLE FEED
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
2
FRAME MP+SOLENOID
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
1
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
3
Frame Dup+Bracket Align Dup
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
2
Frame Dup+Guide Upper Dup
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
4
COVER FRONT+HOLDER LOCKER
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
2
COVER MIDDLE+CAP SUB ACTUATOR
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
1
PBA+COVER KEY MENU_LCD
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
4
COVER CASSETTE+FRAME CASSETTE
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRCH18A
2
S5(WH Long)
6003-000221
BLDC MOTOR+BRKT MOTOR
SCREW-TAPTITE;PWH,+,-,S,M4,L8,ZPC(WHT),SWRCH18A,-
4
S6(BH Short)
6003-000261
PLATE KNOCKUP+CAM KNOCKUP
SCREW-TAPTITE;BH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,-
1
Service Manual
Samsung Electronics
Disassembly and Reassembly
S7(WH Short)
S8(BH Short)
S9(BH Short)
6003-000264
6003-000269
TRAY ASF INPUT UPPER+GEAR PINION
SCREW-TAPTITE;PWH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,-
1
SCREW-TAPTITE;PWH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,-
2
LCD+COVER KEY MENU_LCD
SCREW-TAPTITE;PWH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,-
2
GEAR PINION+FRAME CASSETTE
SCREW-TAPTITE;PWH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,-
1
BRKT MOTOR+BRKT GEAR
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,-
4
SHIELD CONTROLLER+PBA
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,-
3
SHIELD SMPS+SMPS
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,-
4
HVPS+SHIELD HVPS
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,-
3
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,-
2
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,-
4
SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SWRCH18A,-
8
SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SWRCH18A,-
5
SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SWRCH18A,-
10
6003-000282
S10(BH Long)
6003-000301
SHIELD SMPS+EARTH HARNESS
SCREW-TAPTITE;BH,+,-,S,M4,L6,ZPC(WHT),SWRCH18A,-
1
S11(BH Short)
6003-001256
LSU+FRAME BASE
SCREW-TAPTITE;BH,+,B,M4,L10,NI PLT,SWRCH18A
4
S12(BH Long)
6006-001078
SCREW-TAPTITE;PH,+,WSP,B,M3,L10,ZPC(WHT),SWRCH18A,-
3
Service Manual
Samsung Electronics
3-3
Disassembly and Reassembly
3.3 Front Cover
1. Take out the Cassette.
3. If necessary, remove the Toner Cartridge.
Toner Cartridge
Cassette
2. Open the Cover.
4. To remove the Front Cover, first pull the part below
the both side of the Front Cover with a light pressure to the direction of arrow.
1
2
Front Cover
3-4
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.4 MP Tray Ass'y
1. Open the MP Tray Ass'y
3. Apply light pressure to the both side of the MP Tray
Ass'y and pull it in the direction of arrow, as shown
below.
MP Tray Ass'y
MP Tray Ass'y
2. Pull the Tray Links from the both side of the Front
Cover with a light pressure to the direction of arrow.
Tray Link
Service Manual
Samsung Electronics
3-5
Disassembly and Reassembly
3.5 Rear Cover
1. Take out the Duplex Unit.
3. To remove the Face Up Cover, first release the
Stopper Strap in the direction of arrow.
2
1
Duplex Unit
Stopper Strap
2. Remove the four screws securing the Rear Cover
and then Release the Rear Cover from the Set.
Rear Cover
4. Unlatch the Face Up Cover from the Rear Cover
and then release the Face Up Cover, as shown
below.
Face Up Cover
3-6
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.6 Fuser Ass'y
1. Before you remove the Fuser Ass'y, you should open
the face up cover and open the guide output fuser.
- Rear Cover (Refer to 3.5)
2. Remove the four screws securing the Fuser Ass'y
and then pull the Fuser Ass'y.
4. To remove the Electrodes, first release REC
Harness from the left side of the Electrode and
then release the CON Harness from the right side
of the Electrode, as shown below.
REC Harness
Fuser Ass'y
3. Release the CON Harness and REC Harness from
the Thermostat and then remove the three screws
securing the Thermostat and remove it.
Thermostat
CON Harness
REC Harness
Service Manual
Samsung Electronics
3-7
Disassembly and Reassembly
6. Remove the two screws securing the IInput Guide
and remove it.
8. Remove the three screws securing the Idle Gear
Bracket and remove it.
Idle Gear Bracket
Input Guide
7. Unplug the connector from the Input Guide and
remove the one screw securing the Thermistor and
remove it.
9. Remove the one screw securing the Fuser Cover
and release the Fuser Cover from the Fuser
Frame.
Thermister
Fuser Cover
Fuser Frame
3-8
Service Manual
Samsung Electronics
Disassembly and Reassembly
10. Release the Fuser Gear and HR Bush and then
remove the Heat Roller, as shown below.
11. Remove the Jam Link Lever (L,R) and Jam
Holder (L,R) and then remove the Pressure Roller,
as shown below.
Jam Link Lever
Heat Roller
HR Bush
Jam Holder
HR Bush
Fuser Gear
Jam Link Lever
Jam Holder
Service Manual
Samsung Electronics
3-9
Disassembly and Reassembly
3.7 Top Cover
1. Before you remove the Top Cover, you should
remove:
- Rear Cover (Left, Right) (Refer to 3.5)
2. Remove the four screws securing the Top Cover,
as shown below.
3-10
3. To remove the Top Cover, first lift the Top Cover
with a light pressure to the direction of arrow. Then
unplug the OPE Harness, as shown below.
Top Cover
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.8 OPE Unit
1. To remove the OPE Unit, first lift the OPE Unit with
a light pressure to the direction of arrow, Then
unplug the OPE Harness, as shown below.
3. Release the Lens and Keys from the OPE Cover.
OPE Cover
OPE Unit
Lens
Notice : When reassembly the OPE Unit, hole inside
of figure insert a harness.
2. Remove the six screws securing the OPE PBA and
LCD Panel to the OPE Cover and remove it, as
shown below.
LCD Panel
OPE PBA
Service Manual
Samsung Electronics
3-11
Disassembly and Reassembly
3.9 Side Cover (Left, Right)
1. Before you remove the Side Cover (Left, Right),
you should remove:
- Rear Cover (Refer to 3.5)
- Top Cover (Refer to 3.7)
4. Remove the one screw securing the Left Side
Cover, as shown below.
2. Remove the one screw securing the Right Side
Cover, as shown below.
5. Apply light pressure to the bottom of the Left Side
Cover and pull it to the left side in the direction of
arrows, as shown below.
3. Apply light pressure to the bottom of the Right Side
Cover and pull it to the right side in the direction of
arrows, as shown below.
Left Side Cover
Right Side Cover
3-12
Service Manual
Samsung Electronics
Disassembly and Reassembly
6. If necessary, pull the DIMM Cover in the direction
of arrow and remove it, as shown below.
DIMM Cover
Notice : Be careful not to damage the hooks when
remove the Side Cover (Left, Right).
Service Manual
Samsung Electronics
3-13
Disassembly and Reassembly
3.10 Shield Controller Ass'y
1. Before you remove the Shield Controller Ass'y, you
should remove:
- Side Cover Left (Refer to 3.9)
4. Remove the five screws securing the Main PBA to
the Shield and remove it.
2. Unplug the all connectors from the Main PBA.
Main PBA
Insulator Sheet
Shield
3. Remove the three screws securing the Shield
Controller Ass'y and remove it.
5. The connectors are located, as shown below.
LCD OPE
LED OPE
Cartridge
Shield Controller Ass'y
LSU S/W
LSU
Thermistor
MPF_SEN
MPF
REGI
Pick Up
USB
Line
Duplex
BLDC
Engine
3-14
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.11 Drive Ass'y
1. Before you remove the Drive Ass'y, you should
remove:
- Side Cover Left (Refer to 3.9)
3. If necessary, remove the four screws securing the
BLDC Motor Ass'y and remove it.
2. Remove the six screws securing the Drive Ass'y
and remove it.
Gear Bracket Ass'y
Drive Ass'y
BLDC Motor Ass'y
Harness
Notice : The six screws have numbers stamped into
the Drive Ass'y base plate. When refitting the
Drive Ass'y tighten the screws the order they
are numbered. Only screws numbered 1 to 5
are fitted at this stage. Screw 6 is fitted when
the Shield Controller Ass'y is refitted.
Service Manual
Samsung Electronics
3-15
Disassembly and Reassembly
3.12 Duplex Drive Ass'y
1. Before you remove the Duplex Drive Ass'y, you
should remove:
- Side Cover Right (Refer to 3.9)
3. If necessary, remove the two screws securing the
Duplex Motor and remove it.
2. Unplug the connector from the Connection PCB
and remove the three screws securing the Duplex
Drive Unit and remove it.
Harness
Connection
PCB
Bracket Ass'y
Duplex Motor
Duplex Motor
Duplex Drive Ass'y
3-16
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.13 Shield SMPS Ass'y
1. Before you remove the Shield SMPS Ass'y, you
should remove:
- Side Cover Right (Refer to 3.9)
- Duplex Drive Ass'y (Refer to 3.12)
4. Unplug the connector (AC Inlet) and remove the
four screws securing SMPS and remove it.
Shield SMPS (With AC Inlet)
2. Unplug the two connectors (HVPS, Fuser).
AC Inlet Connector
SMPS
Insulator Sheet
Fuser Connector
HVPS Connector
3. Remove the three screws securing the Shield
SMPS Ass'y and remove it.
Shield SMPS Ass'y
Service Manual
Samsung Electronics
3-17
Disassembly and Reassembly
3.14 Connection PCB
1. Before you remove the Connection PCB, you
should remove:
- Side Cover Right (Refer to 3.9)
4. The connectors are located, as shown below.
FAN Duplex Exit Motor
2. Unplug the all connectors.
Duplex
Motor
Fan Main
Connection
PCB
HVPS
3. Remove the two screws securing the Connection
PCB and remove it.
Connection
PCB
3-18
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.15 Fuser Drive Ass'y
1. Before you remove the Fuser Drive Ass'y, you
should remove:
- Side Cover Right (Refer to 3.9)
4. If necnsary, remove the two screws securing the
Step Motor and remove it.
Fuser Exit Bracket Ass'y
2. Unplug the connector from the Connection PCB.
Step Motor
Connection
PCB
Harness
Fuser Drive
3. Remove the three screws securing the Fuser Drive
Ass'y and remove it.
Fuser Drive Ass'y
Service Manual
Samsung Electronics
3-19
Disassembly and Reassembly
3.16 Fan
1. Before you remove the Fan, you should remove:
- Side Cover Right (Refer to 3.9)
3. Remove the two screws securing the Fans and
then pull the Fans (Main, Duplex).
2. Unplug the two connectors from the Connection
PCB, as shown below.
Duplex Fan
Connection
PCB
Duplex Fan
Main Fan
Main Fan
3-20
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.17 Pick Up Roller Ass'y
1. Take out the Cassette.
2. To remove the Pick Up Roller Ass'y, first lift the
notch attached to the Pick Up Roller Ass'y from the
Shaft, then slide the Pick Up Roller Ass'y from left
to right and it will be released completely, as shown
below.
3. To remove the Shaft, first release the locker and
slide the Shaft from left to right, then lift the notch
attached to the Cam so that it's released from the
Shaft. Then release the Bush from the Shaft and
remove the Shaft from the Duplex Guide Housing,
as shown below.
2
3
Shaft
2
Cam
Bush
4
1
1
Locker
Pick Up Roller Ass'y
Service Manual
Samsung Electronics
3-21
Disassembly and Reassembly
3.18 Duplex Guide Housing (With Feed Roller)
1. Before you remove the Duplex Guide Housing, you
should remove:
- Pick Up Roller Ass'y (Refer to 3.17)
4. Pull the Feed Roller from the Bushing.
2. Remove the two screws securing the Duplex Guide
Housing.
Feed Roller
Bushing
Duplex Guide Housing
3. Unplug the one connector (Photo Interrupter) and
remove the Duplex Guide Housing (with Feed
Roller), as shown below.
Photo Interrupter
Connector
1
Duplex Guide
Housing
2
3-22
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.19 HVPS Housing
1. Before you remove the HVPS Housing, you should
remove:
- Duplex Drive Ass'y (Refer to 3.12)
- Unplug the HVPS Connector (Refer to 3.13)
- Pick Up Roller Ass'y (Refer to 3.17)
- Duplex Guide Housing (Refer to 3.18)
4. If necessary, remove the three screws securing the
HVPS and remove it.
2. Remove the eight screws securing the HVPS
Housing, as shown below.
HVPS
Insulator Sheet
Shield
HVPS Housing
3. Unplug the connector for connector PBA and SMPS
first. Unplug the other Connections.
Duplex Motor
Connection PBA
& SMPS
Engine
Duplex Guide
Housing
Service Manual
Samsung Electronics
3-23
Disassembly and Reassembly
3.20 Cover Mid Front
1. Before you remove the Cover Mid Front, you
should remove:
- Top Cover (Refer to 3.7)
- Side Cover (Refer to 3.9)
2. Remove the six screws securing the Cover Mid
Front and release two hooks in the center.
This cover is fragile take care when removing it.
Hook
Hook
Cover Mid Front
3.21 MPF Housing
1. Before you remove the MPF Housing, you should
remove:
- Cover Mid Front (Refer to 3.20)
2. Remove the four screws securing the MPF
Housing and remove it.
3. To remove the MP Pick Up Ass'y, first lift the notch
attached to the left side Stopper so that it's slide the
right to left from the Shaft, then left side Idle slid the
right to left from the Shaft and take out the MP Pick
Up Ass'y, as shown below.
MPF Housing
Stopper
2
1
MPF Housing
3-24
Idle
MP Pick Up Ass'y
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.22 Feed Roller Parts
1. Before you remove the Feed Roller Parts, you
should remove:
- Pick Up Roller Ass'y (Refer to 3.17)
- Duplex Guide Housing (Refer to 3.18)
- Cover Mid Front (Refer to 3.20)
- MPF Housing (Refer to 3.21)
2. Remove the two screws securing the both side of
the Guide Paper and then remove the Guides.
4. Release the E-Ring securing the Feed2 Gear and
remove it.
E-Ring
Feed2 Gear
Guide Paper
5. Remove the three screws securing the Feed
Bracket Unit and then remove the Feed Bracket
Unit and Feed2 Shaft.
Feed Bracket Unit
3. Pull up the Feed Idle Shaft and the Bushs (with
Spring).
Feed Idle Shaft
Feed2 Shaft
Srring
Bush
Service Manual
Samsung Electronics
3-25
Disassembly and Reassembly
6. If necessary, release the three E-Rings securing
the Gears (T2 Idle, Retard, Idle) and then remove
the Gears from the Feed Bracket, as shown below.
8. Pull up the Feed1 Roller from the Bushing, as
shown below.
Idle Gear
Bracket
Feed1 Roller
E-Ring
Retard Gear
T2 Idle Gear
Notice : Be aware of the E-Rings to ensure they are
not lost.
7. Remove the Clutch Unit, as shown below.
Clutch Unit
Feed1 Gear Ass'y
Feed Shaft
3-26
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.23 Pick Up Gear Ass'y & Solenoids
1. Before you remove the Pick Up Gear Ass'y &
Solenoids, you should remove:
- Duplex Guide Housing (Refer to 3.18)
- Feed Bracket Unit (Refer to 3.22.5)
3. Remove the two screws securing the Manual
Solenoid and Feed Solenoid and then remove the
Solenoids, as shown below.
2. Release the Pick Up Gear Ass'y and Pick Up Gear
Shaft, as shown below.
Feed Solenoid
Pick Up Gear Ass'y
Manual Solenoid
Pick Up Gear Shaft
3.24 Exit Roller
1. Before you remove the Exit Roller, you should
remove:
- Top Cover (Refer to 3.7)
- Side Cover (Refer to 3.9)
- Fuser Drive Ass'y (Refer to 3.15)
2. Remove the Exit Gear, and release the Bearing at
one end then remove the Roller Exit F/Down and
Exit Roller Rack, as shown below.
Bearing
Exit Roller Rack
Roller Exit F/Down
1
1
Exit Gear
2
Service Manual
Samsung Electronics
3-27
Disassembly and Reassembly
3.25 LSU
1. Before you remove the LSU, you should remove:
- Top Cover (Refer to 3.7)
- Side Cover (Refer to 3.9)
2. Remove the four screws securing the LSU and
remove it.
LSU
3.26 TERMINAL
1. Before you remove the CRUM2 PBA, you should
remove:
- Top Cover (Refer to 3.7)
- Side Cover (Refer to 3.9)
- LSU (Refer to 3.25)
2. Remove the one screw securing the CRUM2 PBA
and remove it and then release the four Terminals,
as shown below.
CRUM2 PBA
Terminal
Notice : Be aware of the Terminals to ensure they are
not lost.
3-28
Service Manual
Samsung Electronics
Disassembly and Reassembly
3.27 Transfer Roller Parts
1. Before you remove the Transfer Roller Parts, you
should remove:
- Cover Mid Front (Refer to 3.20)
- LSU (Refer to 3.25)
4. To remove the Transfer Roller, first pull the TR Holder
and then take out the Transfer Roller, as shown
below.
2. Remove the three screws securing the Transfer Earth
and remove it.
Transfer Roller
2
Transfer Earth
1
TR Holder
Notice : Do not grab the rubber part of the Transfer
Roller, it may cause a malfunction due to a
foreigen object. Hole the both side of the
Transfer Roller when replacing it.
3. Release the PTL Holder, as shown below.
PTL Holder
Service Manual
Samsung Electronics
3-29
Adjustment and Troubleshooting
4
4. Adjustment and Troubleshooting
4.1 Alignment and Adjustments
4.1.1 Sample Pattern
This product has the several sample patterns for maintenance. With the sample patterns, check the
existence of the abnormality. The patterns help to regularly maintain the product.
4.1.1.1 Printing a Demo Page
Print a demo page or a configuration sheet to make sure that the printer is operating correctly.
Press the Menu button to selection (In formation -> Demo Page)
Service Manual
Samsung Electronics
4-1
Adjustment and Troubleshooting
4.1.2 Control Panel
4.1.2.1 Control Panel
ML-3470D and ML-3471ND
4-2
1
Menu: Enters Menu mode and scrolls through the available
menus.
2
Scroll buttons: Scroll through the options available in the
selected menu, and increase or decrease values.
3
OK: Confirms the selection on the display.
4
Back: Sends you back to the upper menu level.
5
Toner Save: Allows you to save on toner by using less toner
in printing.
6
ML-347x _Duplex: Allows you to print documents on both
sides of the paper.
7
Stop: Stops an operation at any time.
8
Status: Shows the status of your printer.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.1.2.2 System setup
This chapter provides step by step information on setting up your printer.
This chapter includes:
• Using control panel menus
• Menu overview
• Printing a demo page
• Changing the display language
• Using toner save mode
Using control panel menus
A number of menus are available to make it easy for you to change the printer settings. The diagram on the next column
shows the menus and all of the menu items available in each menu.
Accessing control panel menus
You can control your printer from the printer’s control panel. You can also set the control panel menus while the printer is
in use.
1. Press Menu until the menu you want appears on the bottom line of the display and press OK.
2. Press the Scroll buttons until the desired menu item appears and press OK.
3. If the menu item has sub menus, repeat step 2.
4. Press the Scroll buttons to access the desired setting option or the required value.
5. Press OK to save your selection.
An asterisk (*) appears next to the selection on the display, indicating that it is now the default.
6. Press Stop to return to Standby mode.
After 60 seconds of inactivity (no key being pressed), the printer automatically returns to Standby mode.
Service Manual
Samsung Electronics
4-3
Adjustment and Troubleshooting
4.1.2.3 Menu overview
The control panel menus are used to configure the printer. The control panel provides access to the following menus:
Information
Layout
Menu Map
Configuraton
Demo Page
PCL Font List
PS3 Font List
EPSON Font
Orientation
Simplex Margin
Duplexsa
Duplex Margina
Graphic
Paper
Resolution
Darkness
Image Enhance
Copies
Paper Size
Paper Type
Paper Source
Tray Chaining
System Setup
Emulation
Language
Power Save
Auto Continue
Jam Recovery
Altitude Adj.
Auto CR
Job Timeout
Maintenance
Clear Setting
Emulation Type
Setup
Network
a. Available with the ML-347x.
b. Available with optional wireless network interface.
4-4
TCP/IP
EtherTalk
NetWare
Ethernet Speed
Wirelessb
Clear Setting
Network Info
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.1.2.4 Basic Operation of Panel
ML-3470D
Status” LED
Description
Off
Green
ML-3471ND
Power Off / Sleep Mode (When data receive it’ll Wake-up)
On
Ready status
Blink
Blink Slowly : Data Comm. status
Blink Fast : Printing status
Red
On
Error which needs user action
(Toner Empty, Paper Jam, Paper Empty, Cover Open etc..)
Blink
Recoverable Error
(Paper Mismatching, Manual printing in MP Tray)
Warning status
Warning just like supplies exchange (Toner Low etc.)
Service Manual
Samsung Electronics
4-5
Adjustment and Troubleshooting
Error Type
Legacy models Error
Platform model Error
Recoverable Error
Error which can be recoverable
Ex) Jam, Paper Empty, etc.
Error which doesn’t need any special user
actions
Ex) Paper Mismatching, Manual printing in
MP Tray
Error
Just like hardware error which can not be
fixed even if user does special action
Ex) Hsync Error, LSU Error, etc.
Including provider service error which need
some special user or provider actions
Ex) Toner Empty, Paper Jam, Paper Empty,
Cover Open, etc.
Assert behavior
LCD model
- It shows the task name and the lines in
LCD display
LCD model
- It shows the task name and the lines in LCD
display
Operation Map
4-6
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.1.3 Consumables and Replacement Parts
To avoid print quality and paper feed problems resulting from worn parts and to maintain your printer in top working
condition the following items will need to be replaced at the specified number of pages or when the life span of each
item has expired.
COMPONENT
REPLACEMENT CYCLE
Pick-up Roller
150K Pages
Transfer Roller
70K Pages
Fuser
80K Pages
Toner Cartridge
10K Pages(Sales), 4K Pages(Initial)
4.1.4 LED Status Error Message
4.1.4.1 Status LED
Status
Description
Off
• The printer is off-line and cannot print.
• The printer is in power save mode. When data is received, it switches to on-line
automatically.
Green
On
The printer is on-line and can receive data from the computer.
Blinking
• When the backlight blinks slowly, the printer is receiving data from the computer.
• When the backlight blinks quickly, the printer is receiving and printing data.
Red
On
• The toner cartridge is totally exhausted.
Remove the old toner cartridge and install a new one.
• A paper jam has occurred. To solve the problem.
• The front cover is open. Close the front cover.
• There is no paper in the tray. Load paper in the tray.
• The printer has stopped printing due to a major error. Check the display message.
for details on the meaning of the error message.
Blinking
• A minor error is occurring and the printer is waiting for the error to be cleared. Check
the display message. When the problem is cleared, the printer resumes printing.
• The toner cartridge is low. Order a new toner cartridge. You can temporarily improve
print quality by redistributing the toner.
Service Manual
Samsung Electronics
4-7
Adjustment and Troubleshooting
4.1.4.1 Error Message
4-8
Message
Meaning
Suggested solutions
Door Open
The front cover or rear cover is not
securely latched.
Close the cover until it locks into place.
Duplex Jam 0
Check Inside
Paper has jammed during duplex
printing.
Clear the jam.
Duplex Jam 1
Open/Close Door
Paper has jammed during duplex
printing.
Clear the jam.
Fuser Door Open
The fuser door is not securely latched.
Open the rear cover and close the fuser door until
it locks into place.
For the location of the fuser door.
Install Toner
A toner cartridge is not installed.
Install a toner cartridge.
Invalid Toner
The toner cartridge you have installed is
not for your printer.
Install a Samsung-genuine toner cartridge,
designed for your printer.
Load Manual Press
Stop Key
The multi-purpose tray is empty in
manual feed mode.
Load a sheet of print material and press Stop
You need to press Stop each page to be printed.
Low Heat Error
Cycle Power
There is a problem in the fuser unit.
Replace to Fuser Unit.
LSU Hsync Error
Cycle Power
A problem has occurred in the LSU
(Laser Scanning Unit).
Replace to LSU Unit.
LSU Motor Error
Cycle Power
A problem has occurred in the LSU
(Laser Scanning Unit).
Replace to LSU Unit.
Main Motor Locked
There is a problem in the main motor.
Open and then close the front cover.
Open Heat Error
Cycle Power
There is a problem in the fuser unit.
Unplug the power cord and plug it back in.
If the problem persists, please call for service.
Over Heat Error
Cycle Power
There is a problem in the fuser unit.
Unplug the power cord and plug it back in.
If the problem persists, please call for service.
Paper Jam 0
Open/Close Door
Paper has jammed in the feeding area
of the tray.
Clear the jam.
Paper Jam 1
Open/Close Door
Paper has jammed in the fuser area.
Clear the jam.
Paper Jam 2
Check Inside
Paper has jammed in the paper exit
area.
Clear the jam.
Printing...
The printer is printing jobs using
the displayed language.
Complete your printing.
Ready
The printer is on-line and ready to
printer.
Use your printer.
Replace Toner
This message appears between the
Toner Empty and Toner Low status.
Replace the toner cartridge with a new one.
Self Diagnostic...
The engine in your printer is checking
some problems detected.
Please wait a few minutes.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
Message
Meaning
Suggested solutions
Sleeping...
The printer is on power save mode.
When data is received, it switches to on-line
automatically.
Toner Empty
The toner cartridge has run out.
The printer stops printing.
Replace the toner cartridge with a new one.
Toner Low
The toner cartridge is almost empty.
Take out the toner cartridge and thoroughly
shake it. By doing this, you can temporarily
reestablish printing operations.
Tray 1 Paper Empty
There is no paper in the tray 1.
Load paper in the tray 1.
Tray 2 Paper Empty
There is no paper in the optional tray 2.
Load paper in the optional tray 2.
Service Manual
Samsung Electronics
4-9
Adjustment and Troubleshooting
4.1.5 Abnormal Image Printing and Defective Roller
If abnormal image prints periodically, check the parts shown below.
6
2
3
4
1
7
5
1
2
3
4
4-10
5
6
7
OPC Drum
Charge Roller
Supply Roller
Transfer Roller
Heat Roller
Pressure Roller
Developing Roller
No
Roller
Abnormal image period
Kind of abnormal image
1
OPC Drum
75.5mm
White spot, Block spot
2
Charge Roller
37.7mm
Black spot
3
Supply Roller
44.9mm
Horizontal density band
4
Develop Roller
35.2mm
Horizontal density band
5
Transfer Roller
47.1mm
Black side contamination/transfer fault
6
Heat Roller
77.8mm
Black spot and fuser ghost
7
Pressure Roller
62.8mm / 50.24mm
Black side contamination
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.1.6 How to use DCU
4.1.6.1 DCU Setup
You can examine the malfunction of the printer. To perform DCU, open the front discharge cover and leave the
connect the harness wire(10 pin/4 pin) to the CN1(ML-347x) of the Main control board.
ML SERIES DIAGNOSTIC CONTROL UNIT
04 DEV 300
DEV 350
DEV 350
05 LSU READY
LSU MT & LD
LSU MOTOR
07 PAPER EMPTY
PAPER WIDTH
NEW CRU
08
EXIT SENSOR
FEED SENSOR
SELF
TEST
09 COVER OPEN
STATUS
10 COER HEATING PRINTING TEMP READY HEAT
DIAGNOSTIC
OFF
ON
DIAGNOSTIC CODE
00
01
02
03
04
05
06
07
08
09
10
11
MAIN MOTOR OPERATING SYSTEM
MAIN HIGH-VOLTAGE ON
TRNSFER HIGH-VOLTAGE (-)ON
THV(+) REFERANCE VOLTAGE
DEV/SUPPLY HIGH-VOLTAGE ON/PTL ON
LSU OPERATING SYSTEM
PICKUP CLUTCH ON
PEEMPTY/PWITH/NEW CRU TEST
FEED & EXIT SENSOR TEST
COVER OPEN SENSOR TEST
FUSER TEST
HOT BURN TEST
12
CLEAN MODE PRINT
13
THV(+)TRIGGER, ALL HV & FAN ON
14
THV(+) REFERENCE ON
STATUS CODE
61
WARM UP
00
01
02
03
04
READY
READY
READY
READY
READY
20
30
40
50
PRINT START
FEED SENSOR ON
FEED SENSOR OFF
PAPER OUT
69
SLEEP MODE
(REGAL)
(LETTER)
(A4)
(EXECUTIVE)
(B5)
ERROR STATUS CODE
60
62
68
64
70
71
72
73
95
DIAGNOSTIC
MODE
DOWN
UP
OPEN FUSER ERROR
LOW TEMPERATURE ERROR
OVER HEATING ERROR
COVER OPEN ERROR
NO PAPERR
PAPER JAM 0
PAPER JAM 1
PAPER JAM 2
LSU NOT READY
SHIFT
STOP
ENTER
TO ENTER DIAGNOSTIC MODE, PUSH THREE BUTTONS SIMUL ANEOUSL
AND TURN THE PRINTER POWER ON.
Service Manual
Samsung Electronics
4-11
Adjustment and Troubleshooting
4.1.6.2 Code
Connect DCU to the printer and turn the power on. It show 7 Segment FND on the panel and each code tells the
function of the printer.
1) Normal Code
While printing or warming up, it indicate the position of the paper
Code
State
61
00~05
Warm up
Ready(kind of paper)
20, 21, 22
Print Start
30
40
50
69
Feed Sensor On
Feed Sensor off
Paper Out
Sleep Mode
Description
The printer is on, the cover is open or close.
The printer is ready, the paper is detected when the first paper is printed.
00: Legal ,01: Letter ,02: A4 ,03: EXEC ,04: B5 ,05: Folio, 06: A5/A6
The engine controller received the print order from the video controller.
20: 1st, 21: MP, 22: SCF
The paper is passing out of the Feed Sensor.
The paper has passed out of the Feed Sensor.
The paper has passed out of Exit Sensor.
The fuser power turned off to minimize the power consumption.
2) Error Code
When detecting the malfunction, the printing is stopped to indicate error code.
Code
State
60, 62, 68
Fuser Error
64
65
70
71
72
Cover Open
CRU Error
No Paper
Paper Jam 0
Paper Jam 1
73
Paper Jam 2
76
95
Out Bin Full
LSU Not Ready
4-12
Description
The error in the fuser occurred. There is a short circuit in the thermistor
and the thermostat while printing, Low Temperature Error occurs.
• 60: Open Fuser Error
• 62: Low Heat Error
• 68: Over Heat Error
The Printer Cover is open.
The Toner Cartridge not installed,
No paper in the paper cassette.
The front part of paper is jammed between pickup unit and Feed sensor.
The front part of paper is jammed between the Discharge sensor and Feed
sensor.
The front part of paper is jammed just after passing through the discharge
sensor.
The Out bin is filled with paper.
LSU Scanner Motor not ready or Hsync signal not output.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.1.6.3 Self Diagnostic Mode
If Error code occurs due to malfunction of the printer, perform Self Diagnostic Mode to solve the problem.
The printer works only in the self-test mode to solve the malfunction problem.
To enter the self-test mode, turn the power on pressing the buttons of [Down], [Shift] and [Stop] at the same time.
Release the button within 2 or 3 seconds if 78 shows in the DCU. If 00 shows in the DCU, press the button [Up] or
[Shift] to select the self+test , and press the button of [Enter] to operate. To stop, press the button of [shift] and
[Enter] together.
Code
Description
00
Main Motor Operating System
Only the main motor is in operation.
01
Main High Voltage On(THV-)
-1400 voltage output by MHV terminal.
Caution : High voltage probe should be used.
02
Transfer High Voltage(-)On(THV-)
-1000 voltage output by MHV terminal.
Caution : High voltage probe should be used.
03
Transfer High Voltage (+)Reference on (THV +)
+1300 voltage output by MHV terminal.
Caution : High voltage probe should be used.
04
DEV/supply High Voltage : DEV/Supply High Voltage Test.
The left one of the three LEDs in the self-test panel is on when DEV high voltage Supply
high voltage output by each HV terminal. Press the [Up] button to switch the voltage. The
middle and right one of the three LEDs are on and -350 voltage output by DEV HV
terminal.
Caution : High voltage probe should be used.
05
LSU Operating System
The scanning motor of LSU is in operation, the right LED of the three buttons on. Press
the [Up] button to Check LD. LD is functioning and the middle button is on. If the LD is
normal, all LEDs are on.
06
Pickup clutch on
The Solenoid in the printer is in operation. To stop the operation, Press the button [shift]
and [Enter] together.
Service Manual
Samsung Electronics
4-13
Adjustment and Troubleshooting
Code
4-14
Description
07
Paper Empty Sensor Test :
If activate the Actuator of the PEMPTY Sensor, the left and right of the three LEDs are
on.
Paper Empty Sensor ON/OFF
1st LED ON/OFF
08
Feed & Exit Sensor Test
Test the Feed sensor and Discharge sensor in the same way as '07'.
Feed Sensor ON/OFF
2nd LED ON/OFF
Exit Sensor ON/OFF
3rd LED ON/OFF
09
Cover Open Sensor Test
Test the Cover Open Sensor in th same way as code '07’
Cover Open Sensor ON/OFF1st LED ON/OFF
10
Fuser Test
If the [Enter] button pressed, the right LED is on and temperature of the fuser is up to
READY Mode. If the [Up] button pressed, the middle LED is on and temperature of the
fuser is up to Printing Mode.
If you press the button once more, the left LED is on and temperature of the fuser is up to
overheat Mode.
11
Hot Burn Test
If the [enter] button pressed, the printer is continuously printing without detection.
Turn the power off to stop operation.
12
Cleaning Mode Print Mode
Print the paper to clean the OPC Drum in the Cartridge.
13
THV(+) TRIGGER. ALL HV :
All high voltage output by each HV terminal and LSU and the fan is in operation. In this
mode, electronic resistance of transfer roller and high voltage is detected.
14
PTL Test : (ML-1610 : not design)
Indicates the function of the PTL, same method of the code ‘07’.
15
Fan Test :
Indicates the function of the Fan, same method of the code ‘07’.
16
Manual Pickup Test :
Indicates the function of th Manual Pickup, same method of the code ‘07’.
17
Manual Sensor Test :
Indicates the function of the Manual Sensor, same method of the code ‘07’.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
No.
Function
Enter
00
Motor
Motor Run
Motor Stop
01
MHV
Mhv On
Mhv Off
- 1300V
02
THV(-)
Thv Negative On
Thv Negative Off
-1000V
03
THV(+)
Thv On
Thv Off
+1300V
04
DEV
Dev On
Dev Off
-350V
05
LSU
LSU Run
LSU Stop
020mV
06
PickUp
Pickup On
07
PEmpty
08
Sensor
09
Cover
10
Fuser
Fuser On
11
Hot Burn
Hot Burn On
12
Clean Print
Clean Printing
13
15
16
Stop
Supply
DEV
0 : -550V
0 : -350V
On
Off
Ready
Remark
Pickup Off
Paper Empty
Exit
Feed
Cover Open
Fuser Off
Thv
low
Reference
14
Up/Down
adequate
high
PTL
PTL On
PTL Off
FAN
Fan On
Fan Off
Manual Pickup On
Manual Pickup Off
Manual
PTL No
Pic kUp
Manual
17
Sensor
Manual Sensor
4.1.6.4 Self Test Button
If the Self-Test button pressed, vertical lines are printed.
Turn the power on while pressing this button, '89' shows in the DCU and the printer is warming up. After warmingup the printer is in READY Mode, and '88' shows in the DCU. In this mode, without any detection, the printer begins
printing(trial printing and data from the PC). It is convenient to use this mode when the engine malfunction is
detected in the control board.
Service Manual
Samsung Electronics
4-15
Adjustment and Troubleshooting
4.1.7 Paper Jam
4.1.7.1 Clearing paper jams
Message
Location of Jam
Paper Jam 0
In the paper feed area
Open/Close Door
(tray 1, optional tray 2, multi-purpose tray)
Paper Jam 1
Around the toner cartridge
Open/Close Door
Check Inside In the paper exit area
Paper Jam 2
Duplex Jam 0
In the duplex area
Check Inside a
Duplex Jam 1
Between the duplex unit and fuser area
Open/Close Doora
Roller-Exit
Roller-Heat
Duplex
Roller-REGI
Roller-MP
OPC
Roller-Transfer
Roller-Pressure
Roller-Feed
Roller-Pickup
4-16
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.1.7.2 In the paper feed area
In the tray 1
1. Pull the tray 1 open.
3. Pull the tray 1 half.
4. Pull the paper straight up and out.
2. Remove the jammed paper by gently pulling it
straight out. Make sure that all of the paper is
properly aligned in the tray 1.
5. Insert the trays back into the printer. Printing
automatically resumes.
In the multi-purpose tray
1. If the paper is not feeding properly, pull the paper
out of the printer.
If the paper does not move when you pull, or if you
do not see the paper in this area, check the fuser
area around the toner cartridge.
3. Insert the tray 1 into the printer until it snaps into
place. Printing automatically resumes.
In the optional tray 2
1. Pull the optional tray 2 open.
2. Remove the jammed paper from the printer.
2. Open and close the front cover to resume printing.
If the paper does not move when you pull, or if you
do not see the paper in this area, stop and go to
step 3.
Service Manual
Samsung Electronics
4-17
Adjustment and Troubleshooting
4.1.7.3 Around the toner cartridge
1. Open the front cover and pull the toner cartridge
out.
2. Remove the jammed paper by gently pulling it
straight out.
3. Replace the toner cartridge and close the front
cover. Printing automatically resumes.
4.1.7.4 In the paper exit area
1. Open and close the front cover. The jammed paper
is automatically ejected from the printer.
2. Gently pull the paper out of the output tray.
If you do not see the jammed paper or if there is
any resistance when you pull, stop and go to the
next step.
3. Open the rear cover.
4-18
4. If you see the jammed paper, push the pressure
lever on each side up and remove the paper.
Return the pressure lever to its original position and
skip the step 10.
1
pressure lever
If you still do not see the paper, go to the next step.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
5. Release the blue strap, the rear cover stopper, and
fully open the rear cover, as shown.
1
8. Pull the jammed paper out.
If the jammed paper does not move when you pull,
push the pressure lever on each side up to loose
the paper, and then remove it.
1
2
1
2
rear cover stopper
rear cover
1
6. Unfold the duplex guide fully.
pressure lever
9. Return the lever, door, stopper, and guide to their
original position.
10. Close the rear cover. Printing automatically
resumes.
1
1
duplex guide
7. While pushing the fuser lever to the right, open the
fuser door.
1
2
1
2
fuser lever
fuser door
Service Manual
Samsung Electronics
4-19
Adjustment and Troubleshooting
4.1.7.5 In the duplex unit area
If the duplex unit is not inserted correctly, paper jam may occur. Make sure that the duplex unit is inserted correctly.
Duplex jam 0
1. Pull the duplex unit out of the printer.
Duplex jam 1
1. Open the rear cover.
2 Unfold the duplex guide fully.
1
1
1
duplex unit
1
duplex guide
2. Remove the jammed paper from the duplex unit.
3. Pull the jammed paper out.
If the paper does not come out with the duplex unit,
remove the paper from the bottom of the printer.
4-20
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.1.7.6 TiPs for avoiding paper jams
By selecting the correct media types, most paper jams can be avoided.
• Follow the procedures on page 5.5. Ensure that the adjustable guides are positioned correctly.
• Do not overload the tray. Ensure that the paper level is below the paper capacity mark on the inside wall of the
tray.
• Do not remove paper from the tray while your printer is printing.
• Flex, fan, and straighten paper before loading.
• Do not use creased, damp, or highly curled paper.
• Do not mix paper types in a tray.
• Use only recommended print media.
• Ensure that the recommended print side of print media is facing down in the tray, or facing up in the multi-purpose
tray.
• If paper jams occur frequently when you print on A5-sized paper: Load the paper into the tray with the long edge
facing the front of the tray.
In the printer properties window, set the page orientation to be rotated 90 degrees.
Service Manual
Samsung Electronics
4-21
Adjustment and Troubleshooting
4.1.8 Download & Reset F/W
Firmware download method
1.
Normal
Download
method
LCD Panel
2.
3.
4.
1.
2.
Boot
Download
method
LCD Panel
3.
4.
5.
6.
In Do s Prompt ty pes "Usblist2 [ Rom file name] " and Press
Enter
In LCD "Flash Upgrade..." message will be show up.
In LCD "Update Image Please Wait..." message will be
show up.
When download complet e, set will be automatically p ower
On/O ff and it' ll Warming Up
While Pressing Stop k ey, Power O n t he Print er
After verify the m essage "Downl oad Mode Press Stop key"
Press Stop Key
Verify the m essage "Download Mode Plese Send IMG..."
In Do s Prompt ty pes "Usblist2 [ Rom file name] " and Press
Enter
In LCD "Update Image Please Wait..." message will be
show up.
When download complete, set will be automatically power
On/O ff and it' ll Warming Up
Reset method
1.
LCD Panel
4-22
3.
In LCD "Update Image Please Wait..." message will be
show up.
In LCD message Ready¡ Printing then print out
configuration page
Check th e OS version and total pa ge value is "0"
4.
Please set power On/ Off
2.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.2 Troubleshooting
4.2.1 Procedure of Checking the Symptoms
Before attempting to repair the printer first obtain a detailed description of the problem from the customer.
Power On
OP Panel
ON?
- No Power
- Power Module error
- Main PBA error
- LCD Panel error
Ready or
Power save
Indicate
Error Massage
Refer to
Error Massage
<Chapter 4.1.4>
Test Print
printing
Quality is
Nomal?
Refer to "Solution
of Image Problem"
END
Service Manual
Samsung Electronics
4-23
Adjustment and Troubleshooting
4.2.2 The cause and solution of Bad image
1) Vertical Black Line and Band
Description: 1. Straight thin black vertical line occurs in the printing.
2. Dark black vertical band occur in the printing.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Damaged develop roller in
the Toner cartridge. Deformed Doctor-blade
or cleaning-blade.
2. Scratched surface of
the charge roller in the toner cartridge.
If causes 1 and 2 occur in the
toner cartridge, replace the toner
cartridge and try to print out.
Replace the transfer roller if
occurred as No. 3.
3. Partly depression or
deformation on the surface of
the transfer roller.
4-24
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
2) Vertical White Line
Description: White vertical voids in the image.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Foreign matter stuck onto the
window of internal lenses
of LSU mirror.
2. Foreign matter or
toner particles between the toner
cartridge roller and blade. (In case the life of the
toner cartridge has been expired, white
lines or light image occur in
front of the image.)
Foreign matter stuck onto the
window : Clean the LSU window
with recommended cleaner(IPA)
Clean the window with a clean
cotton swab.
Replace the toner cartridge.
3. It may occur when Burr and
foreign substances are on the window
of the toner cartridge frame.
No 3. : Remove the foreign matter
and burr of the exposure window.
(toner cartridge)
4. If the fuser is defective,
voids occur periodically at the
top of a black image.
No. 4. : Open the front cover and
check ribs that corresponds to the
position of the voids. Remove if
found.
5. It may occur when foreign
substances are on the OPC Drum.
6. Partly depression or
deformation on the surface of the
transfer roller
If the problems are not solved,
replace the toner cartridge.
Replace the transfer roller if
occured as NO.6
Service Manual
Samsung Electronics
4-25
Adjustment and Troubleshooting
3) Horizontal Black Band
Description: Dark or blurry horizontal stripes occur in the printing periodically.
(They may not occur periodically.)
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
4-26
1. Bad contacts of the voltage
terminals to toner cartridge.
Clean each voltage terminal of the
Charge, Supply, Develop and
Transfer roller. (remove the toner
particles and paper particles)
2. The rollers of toner
cartridge may be stained.
Charge roller = 37.7mm
Supply roller = 44.9mm
Develop roller = 35.2mm
Transfer roller = 47.1mm
1. Clean the right Gear that has
relatively small gap of the teeth
in the OPC.
2. If the malfunction persists,
replace the toner cartridge.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4) Black/White Spot
Description: 1. Dark or blurry spots occur periodically in the printing
2. White spots occur periodically in the printing
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. If dark or blurry
black spots occur periodically,
the rollers in the Toner
oner cartridge may
be contaminated with foreign matte or
paper particles.
( Charge roller : 37.7 mm interval
OPC drum : 75.5 mm interval)
2. If faded areas or
voids occur in a black image
at intervals of 95 mm, or black spots
occur elsewhere, the OPC drum
surface is damaged.
3. If a black image is
partially broken, the transfer
voltage is abnormal or the transfer
roller's life has expired.
Run OPC cleaning Mode Print
and run the Self-test 2 or 3 times.
In case of 95 mm interval
unremovable in 1, cleanly remove
foreign substances stuck on the
OPC location equivalent to black
spots and white spots with a dry
duster.
1. The transfer roller guarantees
100,000 sheets printing. If the
roller's life is expired, replace it.
2. In case of 95 mm interval
unremovable in 1, take measures
as to replace the toner cartridge
and try to print out.
3. Clean the inside of the set
against the paper particles and
foreign matter in order not to
cause the trouble.
Service Manual
Samsung Electronics
4-27
Adjustment and Troubleshooting
5) Light Image
Description: The printed image is light, with no ghost.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Develop roller is stained when
the toner of toner cartridge is almost
consumed.
4-28
Check if the Toner Save mode is off.
Check if the density is light.
2. Ambient temperature is below than 10°C.
No 1 : Replace the toner cartridge
and try to print out.
3. Bad contact caused by the toner
stains between the high voltage terminal in
the HVPS and the one in the set.
No 2 : Wait 30 minutes after printer
is powered on before you
start printing.
4. Abnormal output from the HVPS.
(Run self-test and check 1~4)
1. No3 : Clean up the contaminated
area by the toner.
2. Replace the HVPS if the
problems are not solved by the
above four instructions.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
6) Dark Image or a Black Page
Description: The printed image is dark.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. No charge voltage in the engine board.
Check the state of the connector
which connects the engine board
and HVPS.
2. Charge voltage is not turned
on due to the bad contacts between
power supply in the side of the Toner
cartridge and charge terminal
of HVPS.
1. Clean the high voltage charge
terminal.
2. Replace the HVPS if not solved
by the above direction 1 and 2.
3. VD0 signal of the Main PBA is Low state.
Replace the LSU Unit or Main PBA.
Service Manual
Samsung Electronics
4-29
Adjustment and Troubleshooting
7) Uneven Density
Description: Print Density is uneven between left and right.
1. The pressure force
on the left and right springs of the
transfer roller is not even, the springs are
damaged, the transfer roller is improperly
installed, or the transfer roller
bushing or holder is
damaged.
2. The life of the Toner cartridge
has expired.
3. The toner level is not even on
the toner cartridge roller due to the
bad blade.
4-30
Replace both the left and right
Spring Holder.
Occur in the toner cartridge gently
shake the toner cartridge.
Replace the toner cartridge and
try to print out.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
8) Background
Description: Light dark background appears in whole area of the printing.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Does character exist less than
2% per a page, and hasn’t it been
used long time?
The toner cartridge is basically
designed to print 7K sheets with
5% image. If it prints more than
8K sheets with 2% coverage, a
background can occur.
2. Is a recycled toner cartridge be used?
The A/S is not guaranteed if using
a recyled the toner cartridger.
3. Has the life span of the toner
cartridge ended?
Replace the toner cartridge when
the life span of it has been ended.
4. Is the movement(Up and Down)
of the transfer roller smooth?
5. Is the HVPS normal?
Clean the bushing part of the
transfer roller.
1. If the problem is still not solved,
replace the toner cartridge.
2. Gently shake the toner
cartridge.
Service Manual
Samsung Electronics
4-31
Adjustment and Troubleshooting
9) Ghost (1)
Description: Ghost occurs at 95 mm intervals of the OPC drum in the whole printing.
95 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Bad contacts
caused by contamination
from toner particles between high voltage
terminal in the main body and the
electrode of the Toner
cartridge.
Clean the terminals when
contaminated by toner particles.
2. Bad contacts caused
by contamination from toner particles
between high voltage terminal in the main
body and the one in the
HVPS board.
Occur in the toner cartridge,
replace the toner cartridge and
try to print out.
3. The life of toner cartridge is expired.
Replace the engine board if not
solved by the above directions 1-2.
4. Transfer roller lifetime(70K sheets)
has expired.
If not solved by the direction 3,
check the transfer roller lifetime
and replace it.
Continue..
4-32
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
Continue..
5. Abnormal low temperature
(below 10°C).
6. Damaged cleaning blade in the
toner cartridge.
Wait about 1 hour after power on
before using printer.
Occur in the toner cartridge,
replace the toner cartridge and
try to print out.
Service Manual
Samsung Electronics
4-33
Adjustment and Troubleshooting
10) Ghost (2)
Description: Ghost occurs at 95 mm intervals of the OPC drum in the whole printing.
(When printing on card stock or transparencies using manual feeder)
95 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
When printing on card stock
thicker than normal paper or
transparencies such as OHP, higher
transfer voltage is
required.
4-34
Select 'Thick Mode' on paper type
menu from the software application
and after using returning to the
original mode is recommended.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
11) Ghost (3) : Fuser
Description: Ghost occurs at 82 or 92 mm intervals.
82 or 92 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
The temperature of the fuser is
maintained high.
Disassemble the fuser and remove
the contaminated toner particles on
the roller and clean the foreign
matter between Thermistor and
Heat roller.
(Caution: can be deformed)
Service Manual
Samsung Electronics
4-35
Adjustment and Troubleshooting
12) Stains on the Face of Page
Description: The background on the face of the printed page is stained.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
4-36
1. Toner leakage due to improperly
sealed toner cartridge.
Replace the toner cartridge.
2. If the transfer roller is
contaminated, stains on the face of
page will occur.
If the transfer roller is
contaminated, run PC Cleaning
Mode Print 2 or 3 times.
And perform Self-Test 2 or 3 times
to remove contamination.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
13) Stains on Back of Page
Description: The back of the page is stained at 57 or 92 mm intervals.
82 or 92 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. 57mm : Transfer roller is
contaminated.
2. 92mm : Pressure roller is
contaminated.
Perform the OPC Cleaning Mode
Print 2 or 3 times. Run Self-Test to
remove the contamination of the
transfer roller.
1. Replace the transfer roller if
contaminated severely.
2. Disassemble the fuser and clean
the H/R(Heat Roller) and P/R
(Pressure roller). And check the
area between H/R and Thermistor.
If contaminated, clean the area
not to be deformed.
Service Manual
Samsung Electronics
4-37
Adjustment and Troubleshooting
14) Blank Page Print out (1)
Description: Blank page is printed.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Bad ground contacts in OPC and/or
toner cartridge.
4-38
1. Check if the Ground-OPC is
defective(set inside left side).
2. Remove contamination of the
terminals of the toner cartridge
and the unit.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
15) Blank Page Print out (2)
Description: 1. Blank page is printed.
2. One or several blank pages are printed.
3. When the printer turns on, several blank pages print.
1. Bad ground contacts in OPC and/or
toner cartridge.
2. Abnormal solenoid.
Remove contamination of the
terminals of the toner cartridge.
1. Perform the engine self test
using EDC Mode to check if the
Solenoid is normal.
2. If not solved by the above
directions 1-2, Replace the
engine board.
3. Turn the power off, delete the
data of PC and try printing again.
Service Manual
Samsung Electronics
4-39
Adjustment and Troubleshooting
4.2.3 The cause and solution of the bad discharge
1) Wrong Print Position
Description: Printing begins at wrong position on the paper.
Wrong sense time caused by defective
feed sensor actuator.
4-40
Replace the defective actuator
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
2) JAM 0
Description: 1. Paper is not exited from the cassette.
2. Jam-0 occurs when the paper feeds into the printer
1. Check the Solenoid by using
EDC Mode.
Replace the solenoid.
2. Check if the pad is loose due to
bad sealing of the side-pad.
Replace the side-pad Assembly
L or R, if necessary.
3. Check the surface of the roller-pickup
for foreign matter.
Clean with soft cloth dampened
with IPA(Isopropyl Alcohol) or
water.
4. If continuous clusters
occur, check whether the assembly
slot between shaft-pickup and
housing-pickup opens or
is broken away.
Replace the Main PBA and/or
Sensor.
5. If the paper feeds into
the printer and Jam 0 occurs, perform
EDC Mode to check feed-sensor
of the engine board.
BIN PATH
Service Manual
Samsung Electronics
4-41
Adjustment and Troubleshooting
3) JAM 1
Description: 1. Recording paper is jammed in front of or inside the fuser.
2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the
Actuator-Feed.
1. If the recording paper is jammed in
front of or inside the fuser.
Replace the SMPS or Exit-Sensor.
2. If the recording paper is
stuck in the discharge roller and the
fuser just after passing through the
Actuator-Feed, Feed Actuator
may be defective.
1. Replace the Main PBA.
2. Reassemble the Actuator-Feed
and Spring-Actuator if the
movement is bad.
BIN PATH
4-42
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4) JAM 2
Description: 1. Recording paper is jammed in front of or inside the fuser.
2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the
Actuator-Feed.
1. If the paper is
completely fed out of the printer,
but Jam 2 occurs : Exit sensor is defective.
• After the paper is completely discharged, actuator
Exit should return to the original position to shut the
photo-sensor. Sometimes it takes longer
hour than it should and does
not return.
Check if the exit sensor actuator is
defective.
• Check if the actuator exit is
deformed (Check if the lever part
is deformed in shape).
• Check whether burrs occur in the
assembly part of the actuator exit
or not and if the actuator is
smoothly operated.
• Check if foreign matter and wire
get caught in the actuator exit's
operation.
2. If the paper is
rolled in the Fuser Roller:
• This occurs when a Guide claw is broken
away or transformed.
• It occurs when the Spring of a Guide claw is broken
away or transformed.
• It occurs when the Heat-Roller or
Pressure-Roller is seriously
contaminated with
the toner.
3. Paper is accordion in the fuser.
If the paper is stuck in the fuser :
disassemble the fuser and remove
the jammed paper, and clean the
surface of the pressure roller with
dry gauze.
Remove the jammed paper after
disassembling the fuser : Clean
the surface of the pressure roller
with dry gauze.
• Remove the toner particles
stained on the rib.
• Check the assemblage and
performance of the exit.
BIN PATH
Service Manual
Samsung Electronics
4-43
Adjustment and Troubleshooting
5) JAM Duplex 1
Description: A message 'Jam duplex 1' is displayed in a LCD window.
1. It is a case that a paper cannot
pass a duplex sensor.
2. It is a case that a paper cannot
reach to a registration sensor after it is
passed a duplex sensor.
Replace a SMPS or main PBA
1. A case that a paper jam occurs
on (A) after it is reversed:
replace a 2nd exit roller after
checking its operation.
2. A case that a paper jam occurs
on (B) after it is reversed:
replace a duplex roller after
checking its operation
BIN PATH
4-44
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
6) JAM Duplex 2
Description: A message 'Jam duplex 2' is displayed in a LCD window.
1. It is a case that a paper cannot
pass a duplex sensor.
2. It is a case that a paper cannot
reach to a registration sensor after it is
passed a duplex sensor.
Replace a SMPS or main PBA.
1. A case that a leading edge of a
paper is jammed on (A) check
an operation of a guide front.
If it is worn or defective, replace it.
2. Check an operation of a feed
roller and a registration roller.
If they are worn or defective
replace them. 2
BIN PATH
Service Manual
Samsung Electronics
4-45
Adjustment and Troubleshooting
7) Multi-Feeding
Description: Multiple sheets of paper are fed at once.
Check the Guide side L/R or Guide
Rear in the Cassette, if the
position is correct.
2. Solenoid malfunction
(the solenoid does not work properly):
Perform EDC Mode.
4-46
Replace the solenoid if necessary.
Replace the Main PBA.
3. Pad-Friction is contaminated
with foreign matter.(oil...)
Clean the pad friction with soft
cloth dampened with IPA
(Isopropyl Alcohol).
4. The face of paper is blended.
Use the smooth paper.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
8) Paper rolled in the fuser
Description: If contaminated at intervals of 57mm on the back of a paper.
1. Contamination of the
pressure roller or heat roller
(Background, Hot off set).
2. Check the claw of the fuser
whether it is deformed.
After disassembling the fuser,
clean contamination between the
heat roller and the thermostor and
remove the contamination of the
pressure roller.
1. If there is heavy background,
repair it by the background
troubleshooting method.
2. Clean the surface of the heat
roller with IPA or water
3. Check the warp or separation
of the print claw and the holder
plate claw, and then manage it.
Service Manual
Samsung Electronics
4-47
Adjustment and Troubleshooting
9) Paper rolled on the OPC Drum
Description: Paper is rolled up in the OPC.
1. Paper is too much thin.
2. The face of paper is curled.
4-48
Recommend to use normal paper.
How to remove the rolled paper
in the OPC
Remove the paper while turning
the OPC against the ongoing
direction.
Clean fingerprints on the OPC
softly with soft cloth dampened
with tissue.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.2.4 The cause and solution of the malfunction
1) Fuser Error
Description: A message "Open fuser/Over heat/Low heat' is displayed in a LCD panel.
1. Check whether a thermostat,
AC wire, and heat lamp are
open or not.
Replace the fuser if a thermostat
is open.
2. Check whether a
thermistor is open or not.
Replace the fuser if a thermistor
sensor is located deep inside of
a sponge.
3. Heat lamp ON/OFF test
Check whether the overheat
mode circuit operates normally
or not.
4. It could not operate
due to a gear of a fuser is melted.
Replace the fuser.
Service Manual
Samsung Electronics
4-49
Adjustment and Troubleshooting
2) LSU Error
Description: A message "PMOTOR ERROR/HSYNC ERROR' is displayed in a LCD panel.
1. Check whether the LSU
connector is disconnected or not.
2. Check whether the LSU
motor is rotating or not.
Replace a LSU
Replace a main board if the same
error occurs again after replacing
a LSU.
3. Check the HSYNC signal.
4-50
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
3) Not function of the gear of the fuser due to melting away
Description: The motor breaks away from its place due to gear melting away.
1. Check the Heat Lamp.
1. Replace the Fuser.
2. Replace the Main PBA.
3. Replace the SMPS.
Service Manual
Samsung Electronics
4-51
Adjustment and Troubleshooting
4) Paper Empty
Description: The paper lamp on the operator panel is on even when paper is loaded in the cassette.
1. Bending or deformation
of the actuator of the paper sensor.
2. The function of the
engine board is defective
Replace the defective actuator.
Replace the Sensor PBA.
3. Check the Connector.
4-52
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
5) Paper Empty without indication
Description: The paper lamp on the operator panel does not come on when the paper cassette is empty.
1. Bending or deformation
of the actuator of the paper sensor.
2. The function of the
engine board is defective
Replace the defective actuator.
Replace the engine board.
Service Manual
Samsung Electronics
4-53
Adjustment and Troubleshooting
6) Cover Open
Description: The ERROR lamp is on even when the print cover is closed.
1. The hook lever in the
top cover may be defective.
2. Check the connector
and circuit of the cover switch department
in the Main Control board.
4-54
Replace the hook lever,
if defective.
1. Check the insertion of the
Cover Open S/W Connect.
2. Replace the Main Control
board or Cover Open S/W.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
7) No error message when the cover is open
Description: The ERROR message does not come on even when the printer cover is open
1. Check the connector and
circuit of the cover switch department
in the Main Control board.
Perform EDC mode
1. Check the insertion of the
Cover Open S/W Connect.
2. Replace the Main Control
board or Cover Open S/W.
Service Manual
Samsung Electronics
4-55
Adjustment and Troubleshooting
8) Defective motor operation
Description: Main motor is not driving when printing, and paper does not feed into the printer, resulting 'Jam 0'.
1. Contamination of the
pressure roller or heat roller
(Background, Hot off set).
2. Check the claw of the fuser
whether it is deformed.
4-56
After disassembling the fuser,
clean contamination between the
heat roller and the thermostor and
remove the contamination of the
pressure roller.
1. If there is heavy background,
repair it by the background
troubleshooting method.
2. Clean the surface of the heat
roller with IPA or water
3. Check the warp or separation
of the print claw and the holder
plate claw, and then manage it.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
9) No Power
Description: When system power is turned on, all lamps on the operator panel do not come on.
1. Check if the power input
and SMPS output are normal.
2. Check the inferiority
of LED-Panel or LDC window on the
front-cover if the OP panel does not
appear after normal
warming-up.
Replace the power supply cord
or SMPS.
1. Replace the control board.
2. Replace the OP panel.
Service Manual
Samsung Electronics
4-57
Adjustment and Troubleshooting
10) Vertical Line Getting Curved
Description: When printing, vertical line gets curved.
1. If the supply of +24v is
unstable in the Main Control board
linking with LSU, check drive by
EDC Mode:
LSU Check.
2. Chect the Deve PBA
in the Toner Cartridge.
4-58
Replace LSU.
1. Replace theToner Joint PBA.
2. Replace the MainPBA.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.2.5 Toner Cartridge Service
It is not guaranteed for the default caused by using other toner cartridge other than the cartridge supplied by the Samsung
Electronic or caused by non-licensed refill production.
4.2.5.1 Precautions on Safe-keeping of Toner Cartridge
Excessive exposure to direct light more than a few minutes may cause damage to the cartridge.
4.2.5.2 Service for the Life of Toner Cartridge
If the printed image is light due to the life of the toner, you can temporarily improve the print quality by redistributing the
toner(Shake the toner cartridge), however, you should replace the toner cartridge to solve the problem thoroughly.
4.2.5.3 Distinguish function for choice cartridge
• Distinguish function for choice cartridge
An EEP ROM is mounted to a cartridge for distinguishing a choice toner cartridge. Items written in below
are detected by checking up memory information.
If the data of the EEP ROM is broken, it cannot be detected.
1) Detecting existence of a toner cartridge: It detects whether a toner cartridge is mounted or not.
2) Detecting a serial number of a toner cartridge.
3) Detecting a toner cartridge supplying company: If it is not Samsung’s, it is not operated.
4) Detecting an OPC rotating counter: It detects the life span of an OPC drum.
• Distinguish a refilled cartridge. (with eyes)
1) Check whether One-way screw is damaged or not
2) Check the cartridge on configuration sheet(Print out the self-test configuration)
: Manufacture date and serial number of toner cartridge are different(permissible range : +/- 1).
Service Manual
Samsung Electronics
4-59
Adjustment and Troubleshooting
4.2.5.4 Error message (LCD window) related in a toner sensor
It explains a message related in toner sensor in a LCD.
4.2.5.4(a) Invalid Toner
- Contents: It is displayed when a supplier is different between a toner cartridge and a set. If this message is shown up,
a printing process cannot operate.
- Solution: Attach a suitable toner cartridge (the same supplier's) to a set. (A unique key has been applied.)
4.2.5.4(b) Low Toner
- Contents: This message shows up when a message "remaining toner: 10%" is displayed in a cartridge count
information.
- Solution: It means that a toner in the toner cartridge has been almost ended. Repare the new toner cartridge.
4.2.5.4(c) Replace Cartridge
- Contents: It means the life span of a toner cartridge (except a toner part) has been ended. Even though a case that a
toner is refilled, the rest of major parts have been ended, so entire toner cartridge might be replaced.
- Solution: If an Toner Cartridge Life cycle Probreum, in a worst case, a toner overflows and it may cause a system fail.
Therefore, recommend a user to replace a toner cartridge.
4-60
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4.2.5.5 Signs and Measures at Poor toner cartridge
Fault
Light image and
partially blank
image
(The life is ended.)
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
Cause & Check
• The printed image
is light or unclean
and untidy.
1. If the image is light or unclean
and untidy printed image Shake the toner cartridge and
then recheck.
• Some part of the
(1)NG: Check the weight of the
image is not printed.
toner cartridge
(2)OK: Lack of toner, so the life
• Periodically a noise
is nearly closed.
as "tick tick" occurs. 2. Some part of image is not
printed - Shake the toner
cartridge and then recheck.
(1)NG: Check the weight of the
toner cartridge and
clean the LSU window
with a cotton swab,
then recheck.
(2)OK: Lack of toner, so the life
is nearly closed.
3. Periodically a noise as "tick
tick" occurs - Measure the
cycle and the weight of the
toner cartridge.
4. White vertical stripes on the
whole screen or partly :
Check the weight of the toner
cartridge.
Toner
Contamination
• Toner is fallen on
the papers
periodically.
• Contaminated with
toner on prints
partly or over the
whole surface.
Solution
1. All of 1, 2, 3 aboveIf it become better by shaking,
replace with a new toner
cartridge after 50-100 sheets in
the closing state of the life span.
2. In case of 2If it becomes better after
cleaning the LSU window, then
the toner cartridge is normal.
(Because of foreign substance
on the LSU window, the image
has not been printed partly.)
3. In case of 3If the cycle of noise is about 2
seconds, the toner inside the
toner cartridge has been nearly
exhausted.( Purchase and
replace with a new toner
cartridge after using about 200
sheets at the point of
occurrence)
4. In case of 3This is a phenomenon caused
by lack of toner, so replace with
a new toner cartridge.
1. Toner is fallen on the paper
periodically.
(1)Check the cycle of the falling
of the toner.
(2)Check the appearance of
both ends of the toner
cartridge OPC drum.
1. If both ends of the OPC drum
are contaminated with toner:
Check the life of the toner
cartridge.
2.The center of the printed
matter is contaminated with
toner.
(1)Check whether foreign
substances or toner are
stuck to the terminal (contact
point) of the toner cartridge.
(2)Check whether the state of
the terminal assembly is
normal.
2. Check whether it could be
recycled.
3. If it cannot be recycled:
Replace the toner cartridge.
Service Manual
Samsung Electronics
4-61
Adjustment and Troubleshooting
Fault
White Black spot
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
• Light or dark black
dots on the image
occur periodically.
• White spots occur
in the image
periodically.
Cause & Check
Solution
1. If light or dark periodical black
dots occur, this is because the
toner cartridge rollers are
contaminated with foreign
substance or paper particles.
(1)38mm interval : Charged
roller
(2)95mm interval : OPC cycle
1. In case of 1 above Run OPC Cleaning Mode Print
4-5 times repeatedly to remove.
Especially check foreign
substance on the OPC surface,
then remove them with a clean
gauze
moistened
with
IPA(Isopropyl Alcohol) not to
damage OPC if necessary.
Never use usual alcohol.
2. If white spots occur in a black
image at intervals of 95mm,
or black spots occur
elsewhere, the OPC drum is
damaged
or
foreign
substance is stuck to the
surface.
Recycled product
3. If a black and white or graphic
image is partially broken at
irregular intervals, the transfer
roller's life has been expired
or the transfer voltage is
abnormal.
• Poor appearance of 1. Poor appearance of the toner
the toner cartridge.
cartridge.
(1)Check the damage to label
• Unclean and rough
and whether different
printouts.
materials are used.
(2)Check the appearance of
• Bad background in
parts of the toner cartridge,
the image.
such as frame, hopper.
2. Unclean and rough printouts.
(1)Check whether foreign
substance or toner are stuck
to the terminal (contact point)
of the toner cartridge.
(2)Check whether the state of
the terminal assembly is
normal.
4-62
2. In case of 2
If they are not disappeared by
running OPC Cleaning Mode
Print 4-5 times.
: at intervals of 38mm - Replace
the toner cartridge.
: at intervals of 95mm - Remove
foreign substance.
: Broken image - Replace the
toner cartridge according to
carelessness.
3. In case of 3 - Exchange the
transfer roller because the life of
the transfer roller in use has been
expired. (Check the transfer
voltage and readjust if different.)
1. In case of 1 (1)If there is an evidence of
disassembling the toner
cartridge.
(2)If materials other than normal
parts of the toner cartridge are
added or substituted.
2. In case of 2 - If there are any
abnormals in connection with
the situation of 1.
(1)It occurs when the toner
cartridge is recycled over 2
times.
(2)If toner nearly being expired
are collected to use, it is
judged as the recycled toner
cartridge.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
Fault
Ghost & Image
Contamination
Signs
Cause & Check
• The printed image
1. The printed image is too light
is too light or dark,
or dark, or partially
or partially
contaminated black.
contaminated black. (1)Check whether foreign
substance or toner are stuck
• Totally
to the terminal(point of
contaminatedblack.
contact) of the toner
(Black image
cartridge.
printed out)
(2)Check whether the terminal
assembly is normal.
• The density of
printouts is too dark
and ghost occurs.
2. Totally contaminated black.
(Black image printed out)
(1)Check whether foreign
substances are stuck to the
terminal(point of contact) of
the toner cartridge and the
state of assembly.
(Especially check the
charged roller terminal.)
3. The printed image is dark and
ghost occurs.
(1)Check foreign substance
attached to the terminal
(point of contact) of the toner
cartridge and the state of
assembly.
(Especially check the
developing roller terminal.)
Solution
1. All of 1, 2, 3 above
(1)Remove toner and foreign
substances adhered to the
contact point of the toner
cartridge.
(2)The contact point of the unit
facing that of the toner
cartridge also must be
cleaned.
(3)If the terminal assembly is
unsafe:
• Fully stick the terminal to or
reassemble
it
after
disassembling.
• Disassemble the side plate and
push the terminal to be stuck,
then reassemble it.
2. In case of 2
It is a phenomenon when the
OPC drum of the toner cartridge
is not electrically charged. Clean
the terminals of the charged
roller, then recheck it.
3. In case of 3
It is a phenomenon as the
developing bias voltage of the
toner cartridge. Clean the
terminals of the developing roller,
then recheck it.
Service Manual
Samsung Electronics
4-63
Adjustment and Troubleshooting
4.2.6 The cause and solutions of bad environment of the software
1) The printer is not working (1)
Description: While Power turned on, the printer is not working in the printing mode.
1. Run Self-Test Mode:
Turn the power on while pressing
the test printing button for 2 or 3 seconds
before printing works.
2. Check if the PC and the
printer is properly connected and
the toner cartridge installed.
3. Printing is nor working in the Windows.
4. Check if the printer cable is
directly connected to peripheral devices
4-64
Check the power of the printer and perform
the Self-Test. If the test printing works, that
means no problems in the printer itself.
If the test printing does not work, that
means bad functioning of the printer
(not because of software).
Replace the printer cable. If the problems
not solved even after the cable replaced,
check the amount of the remaining tone.
(refer to Toner Cartridge Service 4-5)
Check if the connection between PC and printer
port is proper. If you use windows, check if the
printer driver in the controller is set up. If the printer
driver is properly set up, check in which program
the printing is not working. The best way to find out
is to open the memo pad to check the function of
printing. If it is not working in a certain program,
adjust the setup the program requires. Sometimes,
the printout is normal within the Windows basic
programs, but it's not working in a particular
program. In such case, install the new driver again.
If not working in the Windows basic program,
Check the setup of the port of CMOS is on ECP.
And check the address of IRQ 7 and 378
If the scanner needs to be connected to the
printer, first the remove the scanner from
the PC to see if the printer is properly
working alone.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
2) The printer is not working (2)
Description: After receiving the printing order, no response at all or the low speed of printing occurs due to
wrong setup of the environment rather than malfunction of the printer itself.
1. Secure more space of the hard disk.
Not working with the message 'insufficient
printer memory' means hard disk space
problem rather than the RAM problem.
In this case, provide more space for the
hard disk. Secure more space using the
disk utilities program.
2. Printing error occurs even
if there is enough space in the hard disk.
The connection of the cable and printer
port is not proper. Check if the connection
is properly done and if the parallel port in
CMOS is rightly set up.
3. Check the parallel-port-related
items in the CMOS Setup.
As a printer port, Select ECP or SPP
among SPP(Normal), ECP, and EPP
modes(increase printing speed) SPP
normal mode support 8-bit data transfer,
while ECP Mode transfer the 12-bit data.
4. Reboot the system to print.
If the regular font is not printing, the cable
or the printer driver may be defective.
Turn the PC and printer off, and reboot the
system to print again. If not solved,
double-click the printer in my computer If
the regular fonts are not printed this time
again. the cable must be defective so
replace the cable with new one.
Service Manual
Samsung Electronics
4-65
Adjustment and Troubleshooting
3) Abnormal Printing
Description: The printing is not working properly even when the cable has no problem.
(even after the cable is replaced)
If the printer won't work at all or the strange fonts are repeated, the printer driver may be defective
or wrong setup in the CMOS Setup.
1. Set up the parallel
port in the CMOS SETUP.
2. Printer Driver Error.
3. Error message
from insufficient memory.
(The printing job sometimes stops or due
to insufficient virtual memory, but it actually
comes from the insufficient
space of the hard
disk.)
4-66
Select SPP(Normal) or ECP LPT Port the
among ECP, EPP or SPP in the CMOS
Setup.
Check the printer in My Computer.
(to see if the printer driver is compatible to
the present driver or delete the old driver,
if defective and reinstall the new driver)
Delete the unnecessary files to secure
enough space of the hard disk and start
printing job again.
Service Manual
Samsung Electronics
Adjustment and Troubleshooting
4) SPOOL Error
Description: To spool which stands for "simultaneous peripheral operations online" a computer document or
task list (or "job") is to read it in and store it, usually on a hard disk or larger storage medium so that
it can be printed or otherwise processed at a more convenient time (for example, when a printer is
finished printing its current document).
1. Insufficient space of the
hard disk in the directory assigned
for the basic spool.
2. If the previous printing
error not solved.
3. When expected to collide
with other program.
4. When an application
program or the printer
driver is damaged.
5. When some files related to
OS are damaged or virus infected.
6. Memory is less than
suggested one.
Delete the unnecessary files to provide
more space to start printing job.
If there are some files with the extension
name of ****.jnl, Delete them and Reboot
the Windows to restart printing job.
Shut down all other programs except the
current one, if possible.
Delete the printer driver completely and
reinstall it.
After rebooting the computer, check for
viruses, restore the damaged files and
reinstall the program to do the printing job.
Add up enough memory to the PC.
How to delete the data in the spool manager.
In the spool manager, the installed drivers and the list of the documents waiting to be printed
are shown. Select the document to be deleted and check the delete menu.
If you intend to delete the current document being printed, the data being transferred to the
printer will be put out and then the document is removed. Before choosing the document, the
menu is still inactive.
Or put the document out of the list and repeat the routine as in the above or finish the spool
manager.
Service Manual
Samsung Electronics
4-67
5
Exploded Views & Parts List
5. Exploded Views and Parts List
Contents
5.1 Main
5-2
5.7 MP Ass'y
5-14
5.2 Cover Ass'y
5-4
5.8 Main Drive Ass'y
5-16
5.3 Front Cover Ass'y
5-6
5.9 Fuser Drive Ass'y
5-18
5.4 Rear Cover Ass'y
5-8
5.10 Duplex Unit (Optional)
5-19
5.5 OPE Cover Ass'y
5-9
5.11 Fuser Unit
5-21
5.6 Frame
5-10
5.12 Cassette Unit
5-24
LASER PRINTER
The keynote of Product
- Speed: Up to 33ppm (Ltr. 35ppm),
1200x1200dpi Effective output
- Paper Path: MPF Type Cassette
- Emulation: PCL6, PS3
- CPU: SPGPv3
- Memory: 16~64MB Standard
- Cassette: 250 sheet Cassette
- MP: 50 sheet MP
- Lan: 10/100 Base TX (ML-3471ND)
- I/O: USB 2.0, IEEE1284
- Toner: 10K Toner (4K initial)
- Option: 802.11b/g Wireless N/W,
250 sheet Opt. SCF
- Duplex: Built in Duplex
Service Manual
Samsung Electronics
5-1
Exploded Views & Parts List
30
12
11
0
15
16
10
17
2
33
3
33
33
9
1
25
13
13-1
13-2
14
32
6
8
26
24
27
29
7
(Option)
28
31
5.1 Main
5-2
Service Manual
Samsung Electronics
Exploded Views & Parts List
Main Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
Description
Location
QT'y
Service Remark
5.1-0
-
5.1-1
JC96-04522B
ELA HOU-FRAME 220V
SET
D2103
1
SA
5.1-1
JC96-04522A
ELA HOU-FRAME 110V
D2103
1
SA
5.1-2
JC96-03761A
ELA UNIT-MAIN DRIVE
D2101
1
SA
5.1-3
JC96-04706A
ELA HOU-MPF
D2156
1
SA
5.1-6
JC31-00025A
FAN-DC
F0002
1
SA
5.1-7
JC31-00025B
FAN-DC
D2107
1
SA
5.1-8
JC96-04634A
ELA UNIT-MAIN DRIVE
D2100
1
SA
5.1-9
JC97-02697A
MEA-SHIELD CONTROLLER
D2102
1
SA
5.1-10
JC63-00962A
SHEET-INSULATOR_PBA
B2103
1
SNA
5.1-11
JC92-01898A
PBA MAIN-CONTROLLER
D2104
1
SA
5.1-12
JC39-00532A
CBF HARNESS-LCD_OPE
D2113
1
SA
5.1-13
JC97-02652A
MEA-TRANSFER ROLLER
D2128
1
SA
5.1-13-1
JC66-01181A
ROLLER-TRANSFER
D2146
1
SA
5.1-13-2
JC66-00395A
GEAR-TRANSFER
G0448
1
SA
5.1-14
JC59-00027A
UNIT-LSU
D2115
1
SA
5.1-15
JC97-02924A
MEA-COVER
D2105
1
SNA
5.1-16
JC96-04617A
ELA UNIT-INITIAL DEVE(CARTRIDGE-TONER)
1
SNA
5.1-17
JC97-02415A
MEA UNIT-CASSETTE
D2106
1
SA
5.1-24
JC39-00767A
CBF HARNESS-EXIT MTR
A2107
1
SA
5.1-25
JC39-00527A
CBF HARNESS-MAIN MTR
D2111
1
SA
5.1-26
JC97-02393A
MEA UNIT-DUPLEX
D2105
1
SA
5.1-27
JC63-00913A
SHIELD-P-SMPS
A2108
1
SNA
5.1-28
JC39-00523A
CBF HARNESS-AC INLET
D2110
1
SA
5.1-29
6502-000132
CABLE CLAMP
C0069
3
SA
5.1-30
JC63-00960A
SHEET-INSULATOR_SMPS
A2109
1
SNA
5.1-31
JC44-00090A
SMPS-PSP_TYPE3_V2C
D2114
1
SA
5.1-31
JC44-00097A
SMPS-PSP_TYPE3_V1
D2114
1
SA
5.1-32
3903-000042
CBF-POWER CORD(220V)
K2903
1
SA
5.1-32
3903-000085
CBF-POWER CORD(110V)
K2903
1
SA
5.1-33
6502-000121
CABLE CLAMP
C0069
3
SA
New
Service Manual
Samsung Electronics
5-3
Exploded Views & Parts List
2-1
1-1
3
0
1
2
4-1
4-2
1-2
2-2
1-3
7
5
4
2-3
2-3
6
5.2 Cover Ass'y
5-4
Service Manual
Samsung Electronics
Exploded Views & Parts List
Cover Ass’y Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
5.2-0
JC97-02924B
5.2-0
JC97-02924A
Description
Location
QT'y
Service Remark
MEA-COVER
D2105
1
SNA
MEA-COVER
D2105
1
SNA
5.2-1
JC97-02399A
MEA-COVER MIDDLE
D2126
1
SA
5.2-1-1
JC63-00964A
COVER-M_MIDDLE
A2126
1
SNA
5.2-1-2
JC72-01339A
PMO-M-SUB ACTUATOR
A0004
1
SNA
5.2-1-3
JC67-00068C
CAP-M_SUB ACTUATOR
A2127
1
SNA
5.2-2
JC97-02442A
MEA-COVER TOP
D2127
1
SA
5.2-2-1
JC63-00970A
COVER-M_TOP
D2142
1
SA
5.2-2-2
JC72-01346D
PMO-STACKER RX
D2150
1
SA
5.2-2-3
JC72-01343A
PMO-SUB STACKER
Z4139
2
SA
5.2-3
JC97-02396A
MEA-COVER FRONT
D2123
1
SA
5.2-4
JC97-02397A
MEA-COVER SIDE L
D2124
1
SA
5.2-4-1
JC63-00966A
COVER-M_SIDE L
D2140
1
SA
5.2-4-2
JC63-00967A
COVER-M_DIMM
D2141
1
SA
5.2-5
JC97-02882A
MEA-COVER SIDE R
A2128
1
SA
5.2-6
JC97-02732C
MEA-COVER REAR
D2129
1
SA
5.2-7
JC97-02923A
ELA HOU-COVER OPE
A2130
1
SA
Service Manual
Samsung Electronics
5-5
Exploded Views & Parts List
10
8
6
11
7
6
9
5
0
1
3
4
2
5.3 Front Cover Ass'y
5-6
Service Manual
Samsung Electronics
Exploded Views & Parts List
Front Cover Ass'y Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
5.3-0
JC97-02396A
5.3-1
JC63-00969A
5.3-2
5.3-3
5.3-4
5.3-5
Description
Location
QT'y
Service Remark
MEA-COVER FRONT
D2123
1
SA
COVER-M_FRONT
A2123
1
SNA
JC61-01588A
HOLDER-M_LOCKER
D2136
1
SA
JG61-70549A
SPRING ETC-CIS(C2)
C5029
1
SA
JC64-00233A
KNOB-M_LOCKER
D2143
1
SA
JC63-00971A
TRAY-M-ASF_INPUT
T4137
1
SNA
5.3-6
JC63-00444A
TRAY-M-LINK_MP
T4137
2
SA
5.3-7
JC63-00446E
TRAY-M-ASF_INPUT UPPER
D2137
1
SA
5.3-8
JG66-40003A
GEAR-PINION
G0035
1
SA
5.3-9
JC70-00479D
ADJUST-M_MP R
T4138
1
SNA
5.3-10
JC70-00478D
ADJUST-M_MP L
T4139
1
SNA
5.3-11
JC63-00447E
TRAY-M-ASF_FOLDER
D2138
1
SA
Service Manual
Samsung Electronics
5-7
Exploded Views & Parts List
5.4 Rear Cover Ass'y
2
0
3
6
4
5
1
Rear Cover Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
5-8
Drawer#
SEC_Code
5.4-0
JC97-02398D
5.4-1
JC63-00978C
5.4-2
5.4-3
5.4-4
Description
Location
QT'y
Service Remark
MEA-COVER REAR
D2129
1
SA
COVER-REAR
D2130
1
SA
JC63-00968A
COVER-M_FACE UP
C2131
1
SNA
JC63-00937A
COVER-M STACKER REAR
A2132
1
SNA
JC61-01583A
GUIDE-OUTPUT FUSER
A2133
1
SNA
5.4-5
JC61-01653A
STOPPER-M-STRAP
A2134
1
SNA
5.4-6
JC61-01944A
GUIDE-OUTPUT F UPPER
A2135
1
SNA
Service Manual
Samsung Electronics
Exploded Views & Parts List
5.5 OPE Cover Ass'y
0
1
3
7
2
6
8
4
5
9
OPE Cover Ass'y Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
5.5-0
JC97-02923A
5.5-1
JC63-00972P
5.5-2
5.5-3
Description
Location
QT'y
Service Remark
ELA HOU-COVER OPE
D2130
1
SA
COVER-M_KEY MENU_LCD
D2131
1
SNA
JC72-00672A
PCT-LCD WINDOW
B2132
1
SNA
JC67-00147A
LENS LED-M_STATUS
Z4432
1
SNA
5.5-4
JC64-00234A
KEY-M_MENU
B2133
1
SNA
5.5-5
JC64-00235A
KEY-M_BUTTON
B2134
1
SNA
5.5-6
JC64-00047A
KEY-M-SAVE MODE
K0049
1
SA
5.5-7
JC64-00254A
KEY-M_DEMO
B2135
1
SNA
5.5-8
JC64-00236A
KEY-M_STOP
Z4435
1
SNA
5.5-9
JC92-01750A
PBA SUB-OPE
D2153
1
SA
Service Manual
Samsung Electronics
5-9
5-10
12
13
13
9-4
9-6
9-5
14
9
10
3-11
8-3
10-1
8-4
3-12
10-2
8-5
15
10-3
3-13
9-3
9-2
9-1
3-9
3-10
38
8-2
8
54
53
5
55
11
3-9-3
8-1
23
4
3-9-1
24
3-9-2
3-9-1
3-6
20
19
18
21
57
58
3-7
3-3
17
22
53
5
26
3-2
64
25
56
3-5
3-6
3-1
63
65
66
27
66
3
59
60
67
68
Transfer Roller
17
30
76
31
69
28
32
29
27
76
79
62
47
78
36
35
46
43
36-3
36-4
36-2
43-2 43-1
36-1
45
48
77
33
44
1
32
2
37
41
75
51
61
42
49
50
40
62
39
34
0
76
73
74
70
71
72
Exploded Views & Parts List
5.6 Frame
Service Manual
Samsung Electronics
Exploded Views & Parts List
Frame Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
5.6-0
JC96-04522B
5.6-0
JC96-04522A
5.6-1
5.6-2
Description
Location
QT'y
Service Remark
ELA HOU-FRAME 220V
D2103
1
SA
220V
ELA HOU-FRAME 110V
D2103
1
SA
110V
JC61-01620A
FRAME-M_BASE
A2104
1
SNA
JC61-01941A
FRAME-M_EXIT
A2105
1
SNA
5.6-3
JC96-03829B
ELA HOU-GUIDE DUP F
A2106
1
SNA
5.6-3-1
JC61-01600A
GUIDE-M_FRONT DUPLEX
B2107
1
SNA
5.6-3-2
JC66-01187A
LEVER-ACTUATOR EMPTY
D2171
1
SA
5.6-3-3
0604-001095
PHOTO-INTERRUPTER
P0013
1
SA
5.6-3-5
JC63-00992A
SHEET-GUIDE FRONT DU
B2108
1
SNA
5.6-3-6
JC66-00050A
CAM-CATCH
C0004
2
SA
5.6-3-7
JC72-00382B
PMO-BUSHING FEED
O1102
2
SA
5.6-3-9
JC97-02441A
MEA-ROLLER PICK UP
D2175
1
SA
5.6-3-9-1
JC66-01169A
ROLLER-IDLE PICK UP
D2181
2
SA
5.6-3-9-2
JC61-01601A
HOUSING-M_PICK UP
D2178
1
SA
5.6-3-9-3
JC66-01168A
ROLLER-PICK UP
D2180
1
SA
5.6-3-10
JC66-01171A
SHAFT-PICK UP
B2109
1
SNA
5.6-3-11
JC66-01581A
CAM-SHAFT PICK UP
A2110
1
SNA
5.6-3-12
JC72-41364A
PMO-BUSHING_P/U,MP
P0035
1
SA
5.6-3-13
JC66-01173A
ROLLER-FEED
D2170
1
SA
5.6-4
JC66-00527A
SHAFT-FEED IDLE
F6209
1
SA
5.6-5
JC61-00585A
BUSH-M-FEED IDLE
F6043
2
SA
5.6-8
JC97-01788A
MEA UNIT-CLUTCH
C9040
1
SA
5.6-8-1
JC66-00398A
SHAFT-FEED
F6210
1
SA
5.6-8-2
JC72-00981A
PMO-HUB CLUTCH
A2111
1
SNA
5.6-8-3
6107-001171
SPRING-TS
Z4161
1
SA
5.6-8-4
JC72-00978A
PMO-COLLAR_SPRING
Z4125
1
SA
5.6-8-5
JC66-00393A
GEAR-FEED 1
F6071
1
SA
5.6-9
JC97-02394A
MEA UNIT-BRACKET FEED
D2112
1
SA
5.6-9-1
JC61-01582A
BRACKET-P-FEED
D2113
1
SNA
5.6-9-2
JC66-01166A
GEAR-IDLE Z29 HELICAL
D2114
1
SNA
5.6-9-3
6044-000231
RING-E
R0006
1
SA
5.6-9-4
JC66-01164A
GEAR-RETARD 39/19
D2115
1
SNA
5.6-9-5
JC66-00484A
GEAR-T2 IDEL_Z27
G0432
1
SA
5.6-9-6
6044-000125
RING-E
R0004
2
SA
5.6-10
JC97-02648A
MEA UNIT-GEAR PICK UP
D2157
1
SA
5.6-10-1
JC66-01183A
GEAR-PICK UP_INNER
D2116
1
SNA
5.6-10-2
JC66-01184A
GEAR-PICK UP_OUTER
D2117
1
SNA
5.6-10-3
6107-001167
SPRING-CS
Z4318
1
SA
5.6-11
JC66-01160A
SHAFT-M_FEED2
D2118
1
SNA
5.6-12
JC66-01165A
GEAR-FEED2 Z27
D2119
1
SNA
5.6-13
6044-000125
RING-E
R0004
1
SA
5.6-14
JC72-00382B
PMO-BUSHING FEED
O1102
3
SA
5.6-15
JC66-00526A
ROLLER-FEED ROLLER 1
F6201
1
SA
Service Manual
Samsung Electronics
5-11
Exploded Views & Parts List
Frame Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
5-12
Drawer#
SEC_Code
5.6-17
JC72-00983A
5.6-18
6107-001352
5.6-19
5.6-20
Description
Location
QT'y
Service Remark
PMO-LOCKER CST
L6030
2
SA
SPRING-TS
Z4317
1
SA
JC66-00377A
CAM-M-PICK_UP
P2042
1
SA
6044-000001
RING-CS
Z4513
1
SNA
5.6-21
JC33-00025A
SOLENOID-MANUAL
D2120
1
SNA
New
5.6-22
JC33-00027A
SOLENOID-FEED
D2121
1
SA
New
5.6-23
JC63-00917A
GROUND-P-DRIVE
D2122
1
SNA
5.6-24
JC63-00923A
GROUND-P-PUSH BUSHING
B2123
1
SNA
5.6-25
JC63-00922A
GROUND-P-DRIVE2
A2124
1
SNA
5.6-26
6502-001093
CABLE CLAMP
C0002
1
SA
5.6-27
JC61-70932A
SPRING ETC-GUIDE DEVE
Z4159
2
SA
5.6-28
JC72-00984A
PMO-PLATE GUIDE DEVE_L
G2285
1
SA
5.6-29
JC72-00985A
PMO-PLATE GUIDE DEVE_R
G2286
1
SA
5.6-30
JC63-00926A
GROUND-P-SHIELD
A2125
1
SNA
5.6-31
JC65-00019A
TERMINAL-P_CRUM
D2144
4
SA
5.6-32
JC61-00829A
HOLDER-BEARING EXIT F/DOWN
H4009
2
SA
5.6-33
JC97-01034A
MEA RACK-EXIT ROLLER
E4060
1
SA
5.6-34
JC66-01196A
ROLLER-EXIT F/DOWN
B2126
1
SA
5.6-35
JC92-01829A
PBA SUB-TERMINAL
Z4319
1
SA
5.6-36
JC97-01034A
MEA RACK-EXIT ROLLER
E4060
4
SA
5.6-36-1
JC72-41008A
PMO-ROLLER FD R
P0049
1
SA
5.6-36-2
JC72-41007A
PMO-ROLLER FD F
P0048
1
SA
5.6-36-3
JC72-41006A
PMO-HOLDER EXIT ROLL
E4126
1
SA
5.6-36-4
JC61-70911A
SPRING ETC-EXIT ROLL FD
O1053
1
SA
5.6-39
JC63-00920A
GROUND-P-FUSER
B2127
1
SNA
5.6-40
JC63-00925A
GROUND-P-MOTOR FUSER
B2128
1
SNA
5.6-41
JC63-00924A
GROUND-P-SHIELD SMPS
A2129
1
SNA
5.6-42
JC63-00921A
GROUND-P-GUIDE TR
B2130
1
SNA
5.6-43
JC75-00049A
MEC-TERMINAL
K3739
4
SA
5.6-43-1
JC61-00035A
SPRING ETC-HV APOLLO
A2131
1
SNA
5.6-43-2
JC70-00050A
IPR-TERMINAL
Z4562
1
SNA
5.6-44
JC65-00014A
TERMINAL-P-HV CR
C2132
1
SNA
5.6-45
JC70-00312A
IPR-P-TERMINAL CON
K3385
3
SA
5.6-46
JC61-01584A
HOUSING-M_TERMINAL
C2133
1
SNA
5.6-47
JC92-01944A
PBA-CONNECTOR
C2134
1
SA
5.6-48
JC72-00974A
PMO-ACTUATOR CVR OPEN
O1073
1
SA
5.6-49
JC61-01942A
GUIDE-TR RIB
C2135
1
SNA
5.6-50
JC61-00604B
PLATE-E_SAW
P5152
1
SA
5.6-51
JC61-01943A
GUIDE-P-TR
C2136
1
SNA
5.6-53
JC61-70958A
SPRING ETC-TR
Z4163
2
SA
5.6-54
JC61-00914A
PLATE-P-PUSH BUSHING
K3234
2
SNA
5.6-55
JC61-00907A
HOLDER-M-PTL R2
H4041
1
SA
5.6-56
JC70-00307A
IPR-P-EARTH TRANSFER
O1094
1
SA
New
Service Manual
Samsung Electronics
Exploded Views & Parts List
Frame Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
5.6-57
JC61-00047A
5.6-58
JC61-00588A
Description
Location
QT'y
Service Remark
SPRING ETC-TR L HAWK
O1030
1
SA
BUSH-M-TR L
K2886
1
SA
5.6-59
JC72-00102A
PMO-BUSHING_TR(L)
O1101
1
SA
5.6-60
JC63-00918A
GROUND-P-EARTH TR
C2137
1
SNA
5.6-61
JC96-04535A
ELA UNIT-FUSER(220V)
D2122
1
SA
5.6-61
JC96-04534A
ELA UNIT-FUSER(110V)
D2122
1
SA
5.6-62
JC61-00835A
FOOT-BACK
F1010
2
SA
5.6-63
6107-001164
SPRING-TS
Z4156
3
SA
5.6-64
JC61-01619A
HOLDER-M_ACT REGI
C2123
1
SNA
5.6-65
JC66-01191A
LEVER-M_ACTUATOR REGI
B2124
1
SA
5.6-66
JC66-01190A
LEVER-M_ACT DUP OUT
B2125
1
SA
5.6-67
JC61-01618A
HOLDER-M_ACT FEED
C2126
1
SNA
5.6-68
6107-001164
SPRING-TS
Z4156
3
SA
5.6-69
JC39-00524A
CBF HARNESS-LSU S/W
D2133
1
SA
5.6-70
JC63-00914A
SHIELD-P-HVPS
C2127
1
SNA
5.6-71
JC63-00961A
SHEET-INSULATOR_HVPS
C2128
1
SNA
5.6-72
JC44-00157A
HVPS-CYGNUS
B2129
1
SA
5.6-73
JC39-00519A
CBF HARNESS-SMPS
D2164
1
SA
5.6-74
JC39-00518A
CBF HARNESS-ENGINE
D2163
1
SA
5.6-75
JC39-00528A
CBF HARNESS-PAPER EMP
D2166
1
SA
5.6-76
JC61-02155A
PLATE-LSU SUPPORT
C2130
1
SNA
New
Service Manual
Samsung Electronics
5-13
5-14
18
25
20
19
21
22
23
24
17-3
17-2
17-1
24
0
16
26
17
27
15
14
10
9
12
13
5
11
4
8
6
7
2-2
3
2-3
2-1
2-4
2-6
1
2
2-5
Exploded Views & Parts List
5.7 MP Ass'y
Service Manual
Samsung Electronics
Exploded Views & Parts List
MP Ass’y Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
5.7-0
JC96-04706A
5.7-1
JC61-01603A
Description
Location
QT'y
Service Remark
ELA HOU-MPF
D2156
1
SA
FRAME-M_MP
D2157
1
SNA
5.7-2
JC97-02443A
MEA-IDLE FEED
D2158
1
SNA
5.7-2-1
JC61-01604A
HOLDER-M_IDLE FEED
D2159
1
SNA
5.7-2-2
JC61-00484A
SPRING ETC-EXIT LOWER IDLE
Z4180
2
SA
5.7-2-3
JC61-01605A
HOLDER-M_SHAFT IDLE
D2160
2
SNA
5.7-2-4
JC66-01186A
ROLLER-IDLE FEED
D2161
1
SNA
5.7-2-5
JC66-01172A
SHAFT-IDLE FEED
D2162
1
SNA
5.7-2-6
JC63-00997A
COVER-M_IDLE FEED
D2163
1
SNA
5.7-3
JC63-01094A
SHEET-GUIDE MP
D2169
1
SA
5.7-4
JC66-00396A
GEAR-IDLE 23
G0256
1
SA
5.7-5
JC33-00028A
SOLENOID-MP
D2164
1
SA
5.7-6
JC61-00924A
HOLDER-M-PAD_MP
H4029
1
SA
5.7-7
JC73-00140A
RPR-FRICTION PAD
P0034
1
SA
5.7-8
JC61-70911A
SPRING ETC-EXIT ROLL FD
O1053
1
SA
5.7-9
JC61-00927A
PLATE-P-KNOCK UP_MP
D2165
1
SNA
5.7-10
JC72-00761A
PMO-ROLLER CAM.MP
K4061
1
SA
5.7-11
JC73-00141A
RPR-PAD CASSETTE
R0020
1
SA
5.7-12
6107-001237
SPRING-ES
D2166
2
SA
5.7-13
JC61-00926A
HOLDER-M-SENSOR_MP
H4108
1
SA
5.7-14
0604-001095
PHOTO-INTERRUPTER
P0013
1
SA
5.7-15
JC72-01338A
PMO-M-ACT EMPTY MP
K3119
1
SA
5.7-16
JC39-00365A
CBF HARNESS-MPF SEN
H1168
1
SA
5.7-17
JC97-02034A
MEA-PICK UP_MP
D2174
1
SA
5.7-17-1
JC73-00194A
RUBBER-PICK UP MP
P2148
1
SA
5.7-17-2
JC61-00925A
HOUSING-M_PICK UP_MP
D2177
1
SA
5.7-17-3
JC61-00910A
HOUSING-M-PICK UP2_R2
M2078
1
SA
5.7-18
JC66-00710A
GEAR-M-PICK UP_MP
P2110
1
SA
5.7-19
6107-001167
SPRING-CS
Z4318
1
SA
5.7-20
JC66-00709A
GEAR-M-HOLDER_MP
H4073
1
SA
5.7-21
JC66-01205A
CAM-M_PICK UP MP
D2172
1
SA
5.7-22
JC66-00399A
SHAFT-P-PICK_UP
P2160
1
SA
5.7-23
JC61-00915A
STOPPER-M-PICK UP_R2
K3752
2
SA
5.7-24
JC72-00982A
PMO-IDLE PICK_UP
P2131
2
SA
5.7-25
JC66-00720A
SHAFT-P-CORE
O1068
2
SA
5.7-26
JC61-00587A
BUSH-M-PICK_UP R
P2067
1
SA
5.7-27
JC61-00932A
BRACKET-P-PICKUP_MP
P2122
1
SA
Service Manual
Samsung Electronics
5-15
Exploded Views & Parts List
6
2
7
8
6
7
5
4
0
3
1
5.8 Main Drive Ass'y
5-16
Service Manual
Samsung Electronics
Exploded Views & Parts List
Main Drive Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
Description
Location
QT'y
Service Remark
5.8-0
JC96-03761A
ELA UNIT-MAIN DRIVE
D2101
1
SA
5.8-1
JC31-00047A
MOTOR DC-BLDC MAIN
D2108
1
SA
5.8-2
JC61-01593A
BRACKET-P-GEAR MAIN
D2167
1
SNA
5.8-3
JC61-01597A
BRACKET-P-MOTOR MAIN
D2168
1
SNA
5.8-4
JC66-01156A
GEAR-OPC RDCN 93/61
D2169
1
SNA
5.8-5
JC66-01157A
GEAR-OPC DRV 113/33
D2170
1
SNA
5.8-6
JC66-01162A
GEAR-FEED RDCN 55/18
D2171
2
SNA
5.8-7
6031-000023
WASHER-PLAIN
Z6227
2
SA
5.8-8
6302-001056
GASKET
0.2
SNA
Service Manual
Samsung Electronics
5-17
Exploded Views & Parts List
5.9 Fuser Drive Ass'y
0
5
5
3
7
8
6
1
2
4
9
Fuser Drive Ass'y Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
5-18
Drawer#
SEC_Code
5.9-0
JC96-04634A
5.9-1
JC61-01598A
5.9-2
5.9-3
Description
Location
QT'y
Service Remark
ELA HOU-FUSER DRIVE
D2100
1
SA
BRACKET-P-FUSER EXIT
B2102
1
SNA
JC31-00084A
MOTOR STEP-MAIN
C2103
1
SA
JC66-01158A
GEAR-EXIT RDCN 87/24
B2104
1
SNA
5.9-4
6044-000125
RING-E
R0004
1
SA
5.9-5
6044-000231
RING-E
R0006
2
SA
5.9-6
JC66-01163A
GEAR-FUSER RDCN IN 95
D2105
1
SNA
5.9-7
JC66-00417A
GEAR-RDCN FUSER OUT
F4099
1
SA
5.9-8
JC66-00340A
GEAR-HUB CLUTCH
C9033
1
SA
5.9-9
JC66-01210A
GEAR-FUSER IDLE FR
D2173
1
SA
Service Manual
Samsung Electronics
Exploded Views & Parts List
7
2
7
3
4
5
3
6
4
9
8
5
8
10
0
14
1
12
13
14
15
16
11
5.10 Duplex Unit (Optional)
Service Manual
Samsung Electronics
5-19
Exploded Views & Parts List
Duplex Unit (Optional) Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
5-20
Drawer#
SEC_Code
Description
Location
QT'y
Service Remark
5.10-0
JC97-02393A
MEA UNIT-DUPLEX
D2105
1
SA
5.10-1
JC61-01594A
FRAME-M_DUP
B2106
1
SNA
5.10-2
JC61-01596A
BRACKET-P-ALIGN DUP
D2107
1
SNA
5.10-3
JC61-00665A
BUSH-M-FEED, DUP
F6042
4
SA
5.10-4
JC66-01167A
ROLLER-FEED_DUP2
D2108
1
SNA
5.10-4
JC66-00901A
ROLLER-FEED_DUP
D2145
1
SA
5.10-5
JC66-00899A
PULLEY-18_DUP
D2118
2
SA
5.10-6
JC66-00038A
GEAR-EXIT F/DOWN
E4039
1
SA
5.10-7
6003-000196
SCREW-TAPTITE
Z4397
2
SA
5.10-8
6044-000107
RING-C
Z4396
1
SA
5.10-9
JC66-20901A
BELT-TIMMING
B2018
1
SA
5.10-10
JC65-00017A
TERMINAL-P-GND DUP
D2109
2
SNA
5.10-11
JC61-01595A
GUIDE-M_UPPER DUP
D2110
1
SNA
5.10-12
6107-001156
SPRING-TS
Z4317
2
SA
5.10-13
JK72-00058A
PCT-SILP WASHER
D2111
4
SNA
5.10-14
JC66-00896A
ROLLER-M-IDLE_ DUP
D2117
2
SA
5.10-15
JC66-00444A
SHAFT-IDLE ROLL, DUP
S4108
2
SA
5.10-16
6003-000196
SCREW-TAPTITE
Z4397
4
SA
-
JC96-03662B
ELA UNIT-ROLLER_DUP2
1
SNA
-
JC96-03662A
ELA UNIT-ROLLER_DUP
1
SNA
Service Manual
Samsung Electronics
16
19
Samsung Electronics
12
28
15
30
22
29
27
28
2
5
16
45
4
31
3
32
37
Service Manual
45
11
21
14
35
36
43
24
38
42
34
20
23
9
1
17
36
8
24
6
23
33
9
23
24
23 21
35
24
44
37
38
26
26
20
36
39
40
25
14
25
25
26
6
26
34
44
44
0
26
25
18
8
10
25
37
7
Exploded Views & Parts List
5.11 Fuser Unit
5-21
Exploded Views & Parts List
Fuser Unit Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
5-22
Drawer#
SEC_Code
5.11-0
JC96-04534A
5.11-0
JC96-04535A
5.11-1
5.11-2
Description
Location
QT'y
Service Remark
ELA UNIT-FUSER
D2122
1
SA
110V
ELA UNIT-FUSER
D2122
1
SA
220V
JC63-01347A
COVER-FUSER_UPPER
D2123
1
SNA
JC66-01583A
GEAR-EXIT
D2124
1
SNA
5.11-3
JC66-01453A
ROLLER-PRESSURE
Z4588
1
SNA
5.11-4
JC66-01079A
ROLLER-PRESSURE
Z4588
1
SA
5.11-5
JC66-01593A
ROLLER-HEAT
D2125
1
SNA
5.11-6
JC61-01958A
BUSH-HR_R
D2126
2
SNA
5.11-7
JC66-01588A
GEAR-FUSER
D2127
1
SNA
5.11-8
6601-001479
BEARING-BALL
D2128
2
SNA
5.11-9
6107-001159
SPRING-TS
Z4394
2
SA
5.11-10
JC61-01949A
GUIDE-INPUT
C2129
1
SNA
5.11-11
JC67-00253A
CAP-LAMP_L
D2130
1
SNA
5.11-12
JC61-01948A
FRAME-FUSER
B2131
1
SNA
5.11-13
JC61-01955A
GUIDE-REAR
D2132
1
SNA
5.11-14
JC66-01424A
LEVER-LINK JAM
D2133
2
SNA
5.11-15
6107-001237
SPRING-ES
D2134
1
SA
5.11-16
JC61-01977A
HOLDER-JAM
D2135
2
SNA
5.11-17
JC61-02156A
BRACKET-FUSER
D2136
1
SNA
5.11-18
JC67-00254A
CAP-LAMP_R
D2137
1
SNA
5.11-19
JC61-01625A
HOLDER-M_REAR_LEVER
D2138
1
SA
5.11-20
6107-001267
SPRING-CS
Z4482
2
SA
5.11-21
6107-001246
SPRING-CS
Z4602
2
SNA
5.11-22
JC61-70903A
SPRING ETC-ACTUATOR
Z4132
1
SA
5.11-23
JC61-02154A
GUIDE-CLAW
D2139
4
SNA
5.11-24
JC61-01950A
SPRING ETC-CLAW
D2140
4
SA
5.11-25
JC72-20902A
PEX-ROLLER F/UP(2)
O1106
5
SA
5.11-26
JC70-20901A
IEX-SHAFT IDLE,F/UP
D2149
5
SA
5.11-27
JC66-01584A
SHAFT-EXIT_F/UP
D2141
1
SNA
5.11-28
JC61-02158A
BUSH-TX
D2142
3
SNA
5.11-29
JC73-00259A
RUBBER-EXIT_F/UP
D2143
2
SNA
5.11-30
JC66-01423A
ACTUATOR-EXIT
D2144
1
SNA
5.11-31
JC75-00095A
MEC-BRUSH ANTISTATIC
M0022
1
SA
5.11-32
JC70-00538A
ELECTRODE-EARTH
D2145
1
SNA
5.11-33
JC66-01153A
GEAR-IDLE 23 FUSER
Z6116
2
SA
5.11-34
JC61-01960A
BUSH-PR_1ST
D2146
2
SNA
5.11-35
JC61-01961A
BUSH-PR_2ND
D2147
2
SNA
5.11-36
6003-000269
SCREW-TAPTITE
Z4513
4
SA
5.11-37
6003-000282
SCREW-TAPTITE
Z4517
5
SA
5.11-38
6003-000196
SCREW-TAPTITE
Z4397
3
SA
5.11-39
1404-001364
THERMISTOR-NTC ASSY
D2148
1
SA
5.11-40
4712-001031
THERMOSTAT
D2129
1
SA
5.11-41
4713-001207
LAMP-HALOGEN
D2130
1
SA
110V
Service Manual
Samsung Electronics
Exploded Views & Parts List
Fuser Unit Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
Description
Location
QT'y
Service Remark
5.11-41
4713-001208
LAMP-HALOGEN
D2130
1
SA
220V
5.11-42
JC39-00520A
CBF HARNESS-FUSER CON
D2131
1
SA
New
5.11-43
JC39-00609A
CBF HARNESS-FUSER R_2
D2135
1
SA
220V
5.11-43
JC39-00521A
CBF HARNESS-FUSER REC
D2149
1
SA
110V
5.11-44
6044-000231
RING-E
R0006
2
SA
5.11-45
6044-000125
RING-E
R0004
4
SA
Service Manual
Samsung Electronics
5-23
Exploded Views & Parts List
12
5
4-1
14
4
4-2
13
0
4-3
4-4
8
15
7
7
7
3
6
1
10
11
9
2
5.12 Cassette Unit
5-24
Service Manual
Samsung Electronics
Exploded Views & Parts List
Cassette Unit Parts List
SA : SERVICE AVAILABLE, SNA : SERVICE not AVAILABLE
Drawer#
SEC_Code
Description
Location
QT'y
Service Remark
5.12-0
JC97-02415A
MEA UNIT-CASSETTE
D2106
1
SA
5.12-1
JC70-00300A
ADJUST-M-CASSETTE_L
K2014
1
SA
5.12-2
JC70-00301A
ADJUST-M-CASSETTE_R
K2015
1
SA
5.12-3
JG66-40003A
GEAR-PINION
G0035
1
SA
5.12-4
JC97-01931A
MEA UNIT-HOLDER PAD
1
SA
5.12-4-1
JC61-00580A
HOLDER-M-PAD
1
SA
5.12-4-2
JC63-00407A
SHEET-HOLDER PAD R2
1
SNA
5.12-4-3
JC70-00314A
IPR-PLATE PAD
P0009
1
SA
5.12-4-4
JC73-00140A
RPR-FRICTION PAD
P0034
1
SA
5.12-5
JC61-70911A
SPRING ETC-EXIT ROLL FD
O1053
1
SA
5.12-6
JC61-00603A
PLATE-P-KNOCK_UP
1
SNA
5.12-7
6107-001166
SPRING-CS
Z4199
2
SA
5.12-7
JC73-00141A
RPR-PAD CASSETTE
R0020
1
SA
5.12-8
JC66-00719A
CAM-M-KNOCK UP
1
SA
5.12-9
JC61-00876A
FRAME-M_CASSETTE
1
SNA
5.12-10
JC61-00918B
GUIDE-M-EXTENSION L2
E5013
1
SA
5.12-11
JC72-00971A
PMO-EXTENSION SMALL
E5014
1
SA
5.12-12
JC72-00972A
PMO-PLATE_LOCKER
L6051
1
SA
5.12-13
JG61-70531A
SPRING ETC-LOCKER,PLATE
S0025
1
SA
5.12-14
JC63-00974A
COVER-M_SUB CST
1
SNA
5.12-15
JC64-00253A
INDICATOR-M_CASSETTE
1
SNA
Replacement
JC69-00914B
BOX-MAIN
1
SA
Service Manual
Samsung Electronics
5-25
System Diagram
6
6. System Diagram
6.1 Block Diagram
Service Manual
Samsung Electronics
6-1
System Diagram
6.2 Connection Diagram
6-2
Service Manual
Samsung Electronics
Reference Information
7
7. Reference Information
This chapter describes the reference information for applying this training manual, and it is consist-ed
of the tool list, the abbreviation table, the outline of model, and so on.
7.1 Troubleshooting Tool
The following tools are recommended safe and easy troubleshooting as described in this service manual.
• DVM(Digital Volt Meter)
Standard : Indicates more than 3 digits.
• Driver
Standard : "-" type, "+" type (M3 long, M3 short, M2
long, M2 short).
• Cleaning Equipments
Standard : An IPA(Isopropyl Alcohol)dry wipe tissue or
a gentle neutral detergent and lint-free cloth.
• Vacuum Cleaner
• Spring Hook
Standard : For general use
• Tweezers
Standard : For general home use, small type.
• Cotton Swab
Standard : For general home use, for medical service.
• Software (Driver) installation CD ROM
Service Manual
Samsung Electronics
7-1
Reference Information
7.2 Acronyms and Abbreviations(1)
The table below explains the abbreviations and acronyms used in this service manual. Where abbreviations
or acronyms are used in the text please refer to this table.
Abbreviations
7-2
Explanation
AP
Access Point
AC
Alternating Current
APC
Auto Power Control
ASIC
Application Specific Integrated Circuit
ASSY
assembly
BIOS
Basic Input Output System
BLDC
Brush-less Direct Current
CMOS
Complementary Metal Oxide Semiconductor
CN
connector
CON
connector
CPU
Central Processing Unit
dB
decibel
dbA
decibel A
dBM
decibel milliwatt
DC
direct current
DCU
Diagnostic Control Unit
DPI
Dot Per Inch
DRAM
Dynamic Random Access Memory
DVM
Digital Voltmeter
ECP
Enhanced Capability Port
EDC
Embedded Diagnostic control
EEPROM
Electronically Erasable Programmable Read Only Memory
EMI
Electro Magnetic Interference
EP
electrophotographic
EPP
Enhanced Parallel Port
FPOT
First Printout Time
F/W
firmware
GDI
graphics device interface
GND
ground
HBP
Host Based Printing
HDD
Hard Disk Drive
H/H
High temperature and high marshy place
HV
high voltage
HVPS
High Voltage Power Supply
I/F
interface
I/O
Input and Output
IC
integrated circuit
IDE
Intelligent Drive electronics or Imbedded Drive Electronics
Service Manual
Samsung Electronics
Reference Information
Acronyms and Abbreviations(2)
Abbreviations
Explanation
IEEE
Institute of Electrical and Electronics Engineers. Inc
IPA
Isopropy Alcohol
IPM
Images Per Minute
LAN
local area network
lb
pound(s)
LBP
Laser Beam Printer
LCD
Liquid Crystal Display
LED
Light Emitting Diode
L/L
Low temperature and low marshy place
LSU
Laser Scanning Unit
MB
megabyte
MHz
megahertz
MPF
Multi Purpose Feeder
NIC
Network Interface Card
N/N
Normal temperature and normal marshy place
NVRAM
nonvolatile random access memory
OPC
Organic Photo Conductor
OPE
Operate Panel Equipment
PBA
Printed Board Assembly
PCL
Printer Command Language , Printer Control Language
PDL
Page Discription Language
PPM
Page Per Minute
PPS
Pulse Per Second
PS
Post Script
PTL
Pre-Transfer Lamp
PWM
Pulse Width Modulation
Q-PID
Quick Printer Initiating Device
Q ty
quantity
RAM
Random Access Memory
ROM
Read Only Memory
SCF
Second Cassette Feeder
SMPS
Switching Mode Power Supply
SPGP
Samsung Printer Graphic Processor
SPL
Samsung Printer Language
Spool
Simultaneous Peripheral Operation Online
SW
switch
sync
synchronous or synchronization
USB
Universal Serial Bus
WECA
Wireless Ethernet Compatibility Alliance
Service Manual
Samsung Electronics
7-3
Reference Information
7.3 Selecting printer locations
• Leave enough room to open the printer trays, covers, and allow for proper ventilation. (see diagram
below)
• Provide the proper environment :
- A firm, level surface
- Away from the direct airflow of air conditioners,
heaters, or ventilators
- Free of extreme fluctuations of temperature, sunlight,
or humidity
- Clean, dry, and free of dust
7.4 LAN (Optional Function)
• This product can be used with a wired LAN (Option)
• LED Condition and Status
[LED STATUS]
Antenna connector
RJ-45 Jack
LED Condition
Status
Active LED random blink
Normal NPC &Normal packet receive
Active LED regular blink
Normal NPC &No Packet
Active LED Off/On maintenance NPC Initial inferiority
Link LED On
The link LED On OPC,Normally linked
(Red:Wireless,Green:Wire,Orange:Wire)
Active LED(Green)
Link LED Off
Link LED off NPC,Link Inferiority
Link LED
(Red/Green/Orange)
7-4
Service Manual
Samsung Electronics
Reference Information
7.5 Sample Tests Patterns
The sample patterns shown below are the standard test patterns used in the factory.
The life of the toner cartridge, developer cartridge and printing speed are measured with the pattern shown
below (5%). The A4 ISO 19752 standard pattern samples are reproduced reduced to 70% of the actual A4
size.
A4 ISO 19752 Standard Patterns
Service Manual
Samsung Electronics
7-5
7-6
End
OK
Re- printing OK/NG?
Adjust the holder pad to the regular position
NO
Is there the regular position to the
holder pad in the tray?
Occured the double feed
NG
End
OK
NG
Replace the SET
Replace the roller pick up assy.
YES
Is there any problem in the rollerpick up?
Replace the paper tray assy
YES
Reference Information
7.6 Series model solution(ML-3470D and ML-3471ND)
7.6.1 Double Feed Error
Service Manual
Samsung Electronics
Samsung Electronics
En
΀ͼ
΃ΖΡΝΒΔΖ͑ΥΙΖ͑ΡΒΡΖΣ͑ΥΣΒΪ͑ΠΣ͑ΥΙΖ͑ΡΚΔΜΦΡ͑ΣΠΝΝΖΣ
ΒΤΤΪ͟
ΊͶ΄
͵ΠΖΤ͑ΥΙΖ͑ΡΚΔΜΦΡ
ΣΠΝΝΖΣ͑ΣΠΥΒΥΖͰ
Ϳ΀
ʹΙΖΔΜ͑ΚΗ͑ΥΙΖ͑ΗΖΖΕ͑ΤΖΟΤΠΣ͑ΨΠΣΜ͑ΠΣ͑ΟΠΥ͙͚͛͛͟
͑͞ΊΠΦ͑ΔΒΟ͑ΞΒΜΖ͑ΤΦΣΖ͑ΠΗ͑ΚΥ͑ΓΪ͑ΒΔΥΦΒΥΚΟΘ͑ΥΙΖ
ΗΖΖΕ͑ΒΔΥΦΒΥΠΣ͑͟ͺΗ͑ΚΥ͑ΕΠΖΤ͑ΟΠΥ͑ΨΠΣΜ͑͝ΣΖΡΝΒΔΖ
͹·΁΄͑ΞΠΕΦΝΖ͟
Ϳ΀
ʹΙΖΔΜ͑ΚΗ͑ΒΟΪ͑ΠΓΛΖΔΥ͑ΠΣ͑ΠΓΤΥΣΦΔΥΚΠΟ͑ΚΤ͑ΠΟ͑ΥΙΖ
ΡΒΥΙ͑ΓΖΗΠΣΖ͑ΥΙΖ͑ΗΖΖΕ͑ΣΠΝΝΖΣ͑͟ͺΗ͑ΒΟΪ͑͝ΣΖΞΠΧΖ͑ΚΥ͑ΠΣ
ΥΙΖΞ͟
En
΀ͼ
͛͛͑ʹΙΖΔΜ͑ΥΙΖ͑ΤΥΒΥΦΤ͑ΠΗ͑ΤΠΞΖ͑ΡΒΣΥΤ͑ΥΙΣΠΦΘΙ͑ͶΟΘΚΟΖ͑΅ΖΤΥ͑ΞΠΕΖ
͑͢͟΁ΦΤΙ͑ΌΞΖΟΦΎ͔ͪͥ͑͢͢͝͝͝͝͝ΔΠΟΤΖΔΦΥΚΧΖΝΪ͑ΥΠ͑ΖΟΥΖΣ͑ΥΙΖ͑ͶΟΘΚΟΖ͑ΥΖΤΥ
ΞΠΕΖ
ͣ͑͟΄ΖΝΖΔΥ͑Ό͵ΚΒΘΠΟΠΤΥΚΔΎ͑ΞΠΕΖ
ͤ͑͟ͺΟ͑ΥΙΚΤ͑ΞΠΕΖ͑͝ΥΖΤΥ͑ΔΒΟ͑ΔΙΠΠΤΖ͑ΤΠΞΖ͑ΡΒΣΥΤ͑ΥΠ͑ΔΙΖΔΜ͑ΚΥΤ͑ΨΠΜΚΟΘ
ΤΥΒΥ Τ
ʹΙΖΔΜ͑ΥΙΖ͑ΡΚΔΜΦΡ͑ΤΠΝΖΟΠΚΕ͑ΒΟΕ͑ΞΒΚΟ͑ΞΠΥΠΣ
ΨΠΣΜ͑ΠΣ͑ΟΠΥ͑͟ͺΗ͑ΟΖΖΕΖΕ͑͝ΣΖΡΝΒΔΖ͑ΥΙΖΚΣ͑ΡΒΣΥΤ͟
ͿΠ͑͝ͻΒΞΞΖΕ͑ΡΒΡΖΣ͑ΓΖΪΠΟΕ͑ΙΠΝΕΖΣ͑ΡΒΕ͑ΠΣ͑ΗΖΖΕ͑ΣΠΝΝΖΣ͟
΁ΦΝΝ͑ΠΦΥ͑ΥΙΖ͑΅ΣΒΪ͑ΒΟΕ͑ΤΥΒΣΥ͑ΥΙΖ͑ΡΣΚΟΥΚΟΘ͑ΛΠΓ͑ΨΚΥΙ
ͶΞΡΥΪ͑ΒΔΥΦΒΥΠΣ͑ΠΟ͑ΓΪ͑ΝΚΗΥ͑ΦΡΤΚΕΖ͟
ʹΙΖΔΜ͑ΚΗ͑ΥΙΖ͑ΡΚΔΜΦΡ͑ΣΠΝΝΖΣ͑ΚΤ͑ΣΠΝΝΚΟΘ͑ΠΣ͑ΟΠΥ͟
ΊͶ΄
΁ΒΡΖΣ͑ΤΥΚΝΝ͑ΚΟΤΚΕΖ
΅ΣΒΪͰ
ʹΙΖΔΜ͑ΨΙΖΣΖ͑ΥΙΖ͑ΛΒΞΞΖΕ͑ΡΒΡΖΣ͑ΚΤ͑ΝΠΔΒΥΖΕ͟
΀ͼ
΀ͼ
En
En
Reference Information
7.6.2 Jam0
Service Manual
7-7
7-8
End
΀ͼ
ʹΙΖΔΜ͑ΚΗ͑ΒΟΪ͑ΠΓΛΖΔΥ͑ΠΣ͑ΠΓΤΥΣΦΔΥΚΠΟ͑ΚΤ͑ΠΟ͑ΥΙΖ͑ΡΒΥΙ͑͟ͺΗ͑ΒΟΪ͝
ΣΖΞΠΧΖ͑ΚΥ͑ΠΣ͑ΥΙΖΞ͑͟ͶΤΡΖΔΚΒΝΝΪ͑ΥΙΖ͑ΡΒΡΖΣ
ΊͶ΄
Ϳ΀
Ϳ΀
End
΀ͼ
΃ΖΡΝΒΔΖ͑͹·΁΄
Ϳ͸
ʹΙΖΔΜ͑ΥΙΖ͑ΖΩΚΥ͑ΤΖΟΤΠΣ͑ΨΠΣΜΤ͑ΡΣΠΡΠΖΣΝΪ͑ΠΣ͑ΟΠΥ͟
ΊͶ΄
͛͛͑ʹΙΖΔΜ͑ΥΙΖ͑ΤΥΒΥΦΤ͑ΠΗ͑ΤΠΞΖ͑ΡΒΣΥΤ͑ΥΙΣΠΦΘΙ͑ͶΟΘΚΟΖ͑΅ΖΤΥ͑ΞΠΕΖ
͑͢͟΁ΦΤΙ͑ΌΞΖΟΦΎ͔ͪͥ͑͢͢͝͝͝͝͝ΔΠΟΤΖΔΦΥΚΧΖΝΪ͑ΥΠ͑ΖΟΥΖΣ͑ΥΙΖ͑ͶΟΘΚΟΖ͑ΥΖΤΥ
ΞΠΕΖ
ͣ͑͟΄ΖΝΖΔΥ͑Ό͵ΚΒΘΠΟΠΤΥΚΔΎ͑ΞΠΕΖ
ͤ͑͟ͺΟ͑ΥΙΚΤ͑ΞΠΕΖ͑͝ΥΖΤΥ͑ΔΒΟ͑ΔΙΠΠΤΖ͑ΤΠΞΖ͑ΡΒΣΥΤ͑ΥΠ͑ΔΙΖΔΜ͑ΚΥΤ͑ΨΠΜΚΟΘ
ΤΥΒΥ Τ
͵ΠΖΤ͑ΥΙΖ͑ΗΖΖΕ
ΤΖΟΤΠΣ͑ΨΠΣΜ
ΡΣΠΡΖΣΝΪͰ
ΊΖΤ͑͝ͺΥ͑ΣΖΥΦΣΟΤ͑ΓΒΔΜ͑ΚΞΞΖΕΚΒΥΖΝΪ͟
ʹΙΖΔΜ͑ΚΗ͑ΥΙΖ͑ΒΔΥΦΒΥΠΣ͞ΗΖΖΕ͑ΣΖΥΦΣΟΤ͑ΓΒΔΜ͑΢ΦΚΔΜΝΪ͑ΠΣ͑ΟΠΥ͑ΨΙΖΟ
ΪΠΦ͑ΡΦΤΙ͑ΚΥ͑ΕΠΨΟ͟
΃ΖΡΝΒΔΖ͑͹·΁΄
ͿΠ͑͝ΣΖΤΡΠΟΤΖ͑ΠΗ͑ΥΙΖ
ΒΔΥΦΒΥΠΣ͑ΚΤ͑ΥΠΠ͑ΤΝΠΨ͑ΠΣ͑ΚΥ
ΨΠΦΝΕ͑ΟΠΥ͑ΣΖΥΦΣΟ͑ΓΒΔΜ͑ΒΟΪ
ΞΠΣΖ͟
End
΃ΖΡΝΒΔΖ͑ΥΙΖ
ΒΔΥΦΒΥΠΣ͟
End
7.6.3 Jam1
ʹΙΖΔΜ͑ΥΙΖ͑ΤΥΒΥΦΤ͑ΠΗ͑΄ΖΟΤΠΣ͑ΥΙΣΠΦΘΙ͑ͶΟΘΚΟΖ͑΅ΖΤΥ͑ΞΠΕΖ
͑͢͟΁ΦΤΙ͑ΌΞΖΟΦΎ͔ͪͥ͑͢͢͝͝͝͝͝ΔΠΟΤΖΔΦΥΚΧΖΝΪ͑ΥΠ͑ΖΟΥΖΣ͑ΥΙΖ͑ͶΟΘΚΟΖ͑ΥΖΤΥ
ΞΠΕΖ
ͣ͟΄ΖΝΖΔΥ͑Ό͵ΚΒΘΠΟΠΤΥΚΔΎ͑ΞΠΕΖ
ͤ͟ͶΟΥΖΣ͑Ό΄ͶͿ΄΀΃͑΅Ͷ΄΅Ύ͑ΓΪ͑ΡΦΤΙΚΟΘ͑ΌΞΖΟΦΎ͑ΓΦΥΥΠΟ͑ΤΖΧΖΣΒΝ͑ΥΚΞΖΤ
ͥ͟ͶΟΥΖΣ͑ͶΩΚΥ͑΄ΖΟΤΠΣ͑΅Ͷ΄΅͑ΓΪ͑ΡΦΤΙΚΟΘ͑ΟΦΞΖΣΚΔ͑ΌͣΎ͑ΤΖΧΖΣΒΝ͑ΥΚΞΖΤ
ͦ͟ʹΙΖΔΜ͑ΥΙΖ͑ΤΥΒΥΦΤ͑ΠΗ͑ͶΩΚΥ͑ΤΖΟΤΠΣ͑ΓΪ͑ΡΦΤΙΚΟΘ͑ΡΦΝΝ͑ΚΥ͑ΠΦΥ͑ΤΚΕΖ͑ΠΗ͑ΖΩΚΥ
ΣΠΝΝΖΣ
Service Manual
ͽΖΒΕ͑ΖΕΘΖ͑ΠΗ͑ΡΒΡΖΣ͑ΚΤ͑ΝΠΔΒΥΖΕ
ΓΖΥΨΖΖΟ͑ΥΙΖ͑ΗΖΖΕ͑ΒΔΥΦΒΥΠΣ͑ΒΟΕ
ΖΩΚΥ͑ΒΔΥΦΒΥΠΣͰ
ʹΙΖΔΜ͑ΨΙΖΣΖ͑ΥΙΖ͑ΛΒΞΞΖΕ͑ΡΒΡΖΣ͑ΚΤ͑ΝΠΔΒΥΖΕ͟
Reference Information
Samsung Electronics
Samsung Electronics
΅ΙΖ͑ΡΣΠΓΝΖΞ͑ΚΤ͑ΗΚΩΖΕ
΅ΙΖ͑ͶΣΣΠΣ͑ΞΖΤΤΒΘΖ͑ΕΚΤΒΡΡΖΒΣ
΅ΣΒΪ͑͢ΚΤ͑ΤΖΝΖΔΥΖΕ
΅ΙΖ͑ͶΣΣΠΣ͑ΞΖΤΤΒΘΖ͑ΕΠΖΤ͑ΟΠΥ͑ΕΚΤΒΡΡΖΒΣ
ʹΙΖΔΜ͑ΚΗ͑ΥΙΖ͑ΖΣΣΠΣ
ΞΖΤΤΒΘΖ͑ΚΤ͑ΤΥΚΝΝ͑ΠΟ
ΥΙΖ͑ΡΒΟΟΖΝ
ʹΙΒΟΘΖ͑ΥΠ͑Ό΅ΣΒΪ͢Ύ
΅ΣΒΪ͑͢ΚΤ͑ΟΠΥ͑ΤΖΝΖΔΥΖΕ͑
ͺΤ͑Ό΅ΥΣΒΪ͢Ύ͑ΤΖΝΖΔΥΖΕͰ
ʹΙΖΔΜ͑ΥΙΖ͑ΕΖΗΒΦΝΥ͑ΠΗ͑΅ΣΒΪ͑ΠΟ͑ΥΙΖ͑΁ΒΟΟΖΝ
͑͢͟͸Π͑ΥΠ͑ΔΠΡΪ͑ΗΦΟΔΥΚΠΟ͑ΓΪ͑͑ΡΦΤΙΚΟΘ͑͑ΌΔΠΡΪΎ͑ΓΦΥΥΠΟ͑ΠΟ͑ΥΙΖ͑ΡΒΟΟΖΝ
͑ͣ͟͸Π͑ΥΠ͑Ό΄ΪΤΥΖΞ͑ΤΖΥΦΡΎ͑͑ΓΪ͑͑ΡΦΤΙΚΟΘ͑͑ΌΞΖΟΦΎ͑ΓΦΥΥΠΟ͑ΠΟ͑ΥΙΖ͑ΡΒΟΟΖΝ
͑ͣ͟͸Π͑ΚΟΥΠ͑ΌΡΒΡΖΣ͑ΤΖΥΦΡΎ͑ΨΚΥΙ͑ΤΔΣΠΝΝ͑ΜΖΪ͑ΠΗ͑ΒΣΣΠΨ͑ΤΙΒΡΖΕ͑ΒΟΕ͑΁ΦΤΙ͑Ό΀ͼΎ͑ͳΦΥΥΠΟ
͑ͤ͟ʹΙΖΔΜ͑ΥΙΖ͑ΥΣΒΪ͑ΕΖΗΒΦΝΥ͑͝Ό΅ΣΒΪ͢Ύ͝Ό;΁͑΅ΣΒΪΎ͑ΠΣ͑Ό΅ΣΒΪͣΎ͑ΚΟ͑ΔΒΤΖ͑ΠΗ͑ΠΡΥΚΠΟΒΝ͑΅ΣΒΪ
ΊΖΤ͑͝ͺΥ͑ΙΒΡΡΖΟΤ͑ΨΚΥΙ͑͑͢ΠΣ͑ͣ͑ΡΒΘΖΤ
ͿΠ͑͝ΚΥ͑ΙΒΡΡΖΟΤ͑ΣΖΘΒΣΕΝΖΤΤ͑ΠΗ͑ΧΠΝΦΞΖ͑ΚΟ͑ΥΣΒΪ
ΒΟΕ͑ΚΗ͑ΥΙΖΣΖ͑ΚΤ͑ΤΠΞΖ͑ΕΖΗΖΔΥ͑͑͝ΣΖΡΝΒΔΖ͑͸ΦΚΕΖ͑͵ΦΡΝΖΩ͑ͲΤΤΪ
ʹΙΖΔΜ͑ΥΙΖ͑ΕΒΞΒΘΖ͑ΠΣ͑ΚΟΔΠΞΡΝΖΥΖΕ͑ΤΙΒΡΚΟΘ͑ΠΗ͑ͲΔΥΦΒΥΠΣ͑ͶΞΡΥΪ͑ΚΟ
ͳΒΤΖ͑ͷΣΒΞΖ͑ΒΤΤΖΞΓΝΪ
ʹΙΖΔΜ͑ΚΗ͑ΚΥ͑ΙΒΡΡΖΟ
ΨΚΥΙ͑ΛΦΤΥ͑͢ΠΣ͑ͣ
ΡΒΡΖΣΤ͑ΚΟ͑ΥΣΒΪ
΅ΙΖ͑ΤΖΟΤΚΟΘ͑ΚΤ͑ΨΠΣΜΚΟΘ͑ΨΖΝΝ
΃ΖΡΝΒΔΖ͑͑ͣͦ͑͡ΤΙΖΖΥ͑΅ΣΒΪΌʹͦͣ͢͡Ύ
΃ΖΡΝΒΔΖ͑͑͢͢͡·͑ͶΟΘΚΟΖ͑΁ΠΨΖΣ
ΓΠΒΣΕ͑ͲΤΤΪΌͿͦͧͪͧΎ
΅ΙΖ͑ΤΖΟΤΚΟΘ͑ΚΤ͑Ϳ΀΅͑ΨΠΣΜΚΟΘ͑ΨΖΝΝ
ʹΙΖΔΜ͑ΚΗ͑ΤΖΟΤΚΟΘ͑ΥΙΖ
ΡΒΡΖΣ͑ΚΤ͑ΨΠΣΜΚΟΘ͑ΨΖΝΝ
ʹΙΖΔΜ͑ΥΙΖ͑ΤΥΒΥΦΤ͑ΠΗ͑΄ΖΟΤΠΣ͑ΥΙΣΠΦΘΙ͑ͶΟΘΚΟΖ͑΅ΖΤΥ͑ΞΠΕΖ
͑͢͟΁ΦΤΙ͑ΌΞΖΟΦΎ͔ͪͤ͑͢͢͝͝͝͝͝ΔΠΟΤΖΔΦΥΚΧΖΝΪ͑ΥΠ͑ΖΟΥΖΣ͑ΥΙΖ͑ͶΟΘΚΟΖ͑ΥΖΤΥ
ΞΠΕΖ
ͣ͟΄ΖΝΖΔΥ͑Ό͵ΚΒΘΠΟΠΤΥΚΔΎ͑ΞΠΕΖ
ͤ͟ͶΟΥΖΣ͑Ό΄ͶͿ΄΀΃͑΅Ͷ΄΅Ύ͑ΓΪ͑ΡΦΤΙΚΟΘ͑ΌΞΖΟΦΎ͑ΓΦΥΥΠΟ͑ΤΖΧΖΣΒΝ͑ΥΚΞΖΤ
ͥ͟ͶΟΥΖΣ͑ͶΞΡΥΪ͑΄ΖΟΤΠΣ͑΅Ͷ΄΅͑ΓΪ͑ΡΦΤΙΚΟΘ͑ΟΦΞΖΣΚΔ͑ΌͣΎ͑ΤΖΧΖΣΒΝ͑ΥΚΞΖΤ
ͦ͟ʹΙΖΔΜ͑ΥΙΖ͑ΤΥΒΥΦΤ͑ΠΗ͑ΖΞΡΥΪ͑ΤΖΟΤΠΣ͑ΓΪ͑ΡΦΤΙΚΟΘ͑ΟΦΞΖΣΚΔ͑Ό͢Ύ͑ΨΚΥΙ
ΒΔΥΦΒΥΠΣ͑ΡΦΤΙΖΕ͑ΒΟΕ͑ΣΖΝΖΒΤΖΕ͑ΒΝΥΖΣΟΒΥΚΧΖΝΪ
Reference Information
7.6.4 No Paper/Add Paper" error on the printer and have been unable to
clear it, even when they have verified there is paper in the printer
Service Manual
7-9
7-10
΃ΖΡΝΒΔΖ͑ΥΙΖ͑ͳΒΤΖ͑ͷΣΒΞΖ͑ͲΤΤΖΞΓΝΪ͑ΌͻͦͪͨͥΎ
΄ΥΚΝΝ͑ΡΣΠΓΝΖΞ͑͑ΗΚΩΖΕ͑Ͱ
͢͟΃ΖΡΝΒΔΖ͑͑͢͢͡·͑ͶΟΘΚΟΖ͑΁ΠΨΖΣ͑ΓΠΒΣΕ͑ͲΤΤΪΌͿͦͧͪͧΎ
Reference Information
7.6.5 Open Cover Error
Service Manual
Samsung Electronics
Samsung Electronics
Toner should be shortage, Replace New Toner
No
Is the page printed
clearly?
Try to do print job for checking
Pull out Toner Cartridge from the SET and Shake the Toner
2 or 3 times, Reinstall Toner to the SET
: The solid Orange Error LED is on, which means toner low status.
solid ORANGE Led
Reference Information
7.6.6 Low Toner
Service Manual
7-11
7-12
Turn off the Printer.
Replace Fuser
YES
Is the same LED message
shown again?
Turn on the printer.
Turn off the printer and stay for 5minute.
OVER HEAT ERROR
Check how the LED is diplayed
NO
Try to do print
job
Turn off the Printer.
Replace Fuser
YES
YESLED
Is the same
message shown
NO
OK
Reference Information
7.6.7 Over Heat Error
Service Manual
Samsung Electronics
Samsung Electronics
Turn off the Printer.
Replace Fuser
YES
Is the same LED
message shown again?
No
Try to do print
job
Turn off the Printer.
Replace Fuser
YES
Is the same LED
message shown
NO
OK
7.6.8 Low Heat Error
Try to reboot
LOW HEAT ERROR
Check how the LED is diplayed
Reference Information
Service Manual
7-13
7-14
Turn off the Printer.
Replace Fuser
YES
Is the same LED message
shown again?
No
Try to do print job
Turn off the Printer.
Replace Fuser
YES
Is the same LED message
shown again?
NO
OK
7.6.9 Fuser Door Open
Open the rear cover and fuser door.
Close the fuser door and rear cover.
Fuser Door Open
Check how the LED is diplayed
Reference Information
Service Manual
Samsung Electronics
Samsung Electronics
En
΃ΖΡΝΒΔΖ͑ͽ΄Ά͑ΠΣ͑ΗΒΟ͙Τ͚
Β͑ΜΚΟΕ͑ΠΗ͑ΙΚΘΙ͑ΤΡΖΖΕ
ΟΠΚΤΖ
ΈΙΒΥ͑ΜΚΟΕΤ͑ΠΗ
ΟΠΚΤΖ͑͑ΔΒΟ͑ΪΠΦ
ΙΖΒΣͰ
ΊͶ΄
ͿΠ͑͝ΚΥ͘Τ͑ΗΣΠΞ͑ΤΔΒΟΟΖΣ͟
En
ʹΙΖΔΜ͑ΒΝΝ͑ΜΚΟΕΤ͑ΠΗ͑ΕΣΚΧΚΟΘ͑ΘΖΒΣΤ͝
ΡΚΟΚΠΟΤ͑ΒΟΕ͑ΤΠΝΖΟΠΚΕΤ͑͝ΚΗ͑ΟΖΔΖΤΤΒΣΪ
ΣΖΡΝΒΔΖ͑ΚΥ͙ΥΙΖΞ͚͑ΠΣ͑ΓΒΤΖ͞ΗΣΒΞΖ͟
Β͑ΜΚΟΕ͑ΠΗ͑ΧΚΓΣΒΣΚΠΟ͑ΟΠΚΤΖ͑ΒΟΕ͑ΟΠ
ΗΖΖΕΚΟΘ͑ΡΒΡΖΣ͑ΗΣΠΞ͑΅ΣΒΪ͢
ͺΤ͑ΡΣΚΟΥΖΣ͑ΞΒΜΚΟΘ͑ΟΠΚΤΖ
ΗΣΠΞ͑ΝΠΨΖΣ͑ΖΟΘΚΟΖͰ
ͷΚΟΕ͑Β͑ΤΠΦΣΔΖ͑ΠΗ͑ΟΠΚΤΖ
En
ΔΙΖΔΜ͑ΕΦΡΝΖΩ͑ΒΤΤΪ͑ΚΤ͑ΗΚΥΥΖΕ͑ΔΠΣΣΖΔΥΝΪ
ΠΣ͑ΔΙΖΔΜ͑ΚΗ͑ΕΦΡΝΖΩ͑ΕΣΚΧΚΟΘ͑ΞΠΥΠΣ͑ΚΤ
ΞΒΜΚΟΘ͑ΟΠΚΤΖ͑ΓΪ͑ΚΥΤΖΝΗ͑͟ͺΗ͑ΟΖΔΖΤΤΒΣΪ͝
ΣΖΡΝΒΔΖ͑ΥΙΖ͑ΞΠΥΠΣ͟
Β͑ΜΚΟΕ͑ΠΗ͑ΧΚΓΣΒΣΚΠΟ͑ΟΠΚΤΖ͑ΒΟΕ͑ΟΠ
ΗΖΖΕΚΟΘ͑ΡΒΡΖΣ͑ΗΣΠΞ͑ΕΦΡΝΖΩ
ΞΠΕΦΖ
͵Π͑ΪΠΦ͑ΙΖΒΣ͑Β͑ΜΚΟΕ͑ΠΗ
ΙΚΘΙ͑ΗΣΖ΢ΦΖΟΥ͑ΗΣΚΔΥΚΠΟΒΝ
ΟΠΚΤΖ͑ΨΙΖΟ͑ΕΠΔΦΞΖΟΥ
ΗΖΖΕΚΟΘͰ
Ϳ΀
͵Π͑ΪΠΦ͑ΙΖΒΣ͑Β͑ΜΚΟΕ͑ΠΗ
ΧΚΓΣΒΥΚΠΟ͑ΟΠΚΤΖ͑Γ͠Ψ
ΘΖΒΣΤ͑ΠΣ͑ΞΠΥΠΣͰ
΃ΖΡΝΒΔΖ͑Ͳ͵ͷ͑͹ΠΝΕΖΣ
΁ΒΕ͟
΃ΖΡΝΒΔΖ͑Ͳ͵ͷ͑ΞΠΕΦΝΖ͟
En
΃ΖΡΝΒΔΖ͑;΁ͷ
Β͑ΜΚΟΕ͑ΠΗ͑ΧΚΓΣΒΣΚΠΟ͑ΟΠΚΤΖ͑ΒΟΕ͑ΟΠ
ΗΖΖΕΚΟΘ͑ΡΒΡΖΣ͑ΗΣΠΞ͑;΁ͷ
ΊͶ΄
ΊͶ΄
΀ͼ
΀ͼ
En
En
Reference Information
7.6.10 A noise troubleshooting tree
Service Manual
7-15
Reference Information
7.6.11 LSU Error
: The ERROR and Online LED are blinking together
Check how the LED is diplayed
No
LSU Error on the pannel?
Try to do print job
Is the same error
message on the pannel ?
YES
Try to reboot the printer
Is the same error
message on the pannel?
No
Turn off the Printer.
Replace LSU
YES
Turn off the Printer.
Replace LSU
7-16
Service Manual
Samsung Electronics
Samsung Electronics
Yes
Check t to push
the cancel button
No
No
Replace Scanning Unit Assy
Yes, Still there is unlock error message on the pannel
YES
Are you sure that
swich is pulled out
completedly?
Check if the switch is pulled out
completedly to the unlock mark inside
platen glass
Yes
Still is there unlock
error message on
the pannel?
Push [cancel] button
Pull out the switch with
Ice green color
No
Fix the problem
Reference Information
7.6.12 Scan Lock Error
Service Manual
7-17
7-18
OK
En
d
After connected
well, Try to
reboot the
printer Copying
No
Check if the OPE's
connection cable was
connected well with MainBoardl
Yes
Check if the LCD wasn't
displayed
NG
OK
En
d
Try to reboot
the printer
Replace OPE Unit Assy
Yes
NG
En
d
Try to reboot
the printer
Replace Main-Board
Reference Information
7.6.13 Nothing Displayed on LCD
Service Manual
Samsung Electronics
Samsung Electronics
Replace the HVPS
Yes
Is there still remaing the
problem?
Replace the Frame ass'y
YES
Check if OPC Drum have
all black toners on the
whole surface after
warming up?
All black printing while printing
No
No
End
Replace Toner Cartridge
Reference Information
7.6.14 All black printing
Service Manual
7-19
7-20
En
d
OK
After put the
document, Copying.
No
Check whether
there is document
to copy
NG
Yes
OK
En
d
After put other
document, Copying.
Yes
Check if the
document was
white paper
NG
No
En
d
OK
Copying.
No
Check if the
CCD's flat cable
was connected
well
`
NG
En
d
Copying.
Replace CCD
Check if the
CCD's Lamp
operated well
Yes
En
d
Copying.
Replace Scanning Unit Assy
Reference Information
7.6.15 Blank Copy
Service Manual
Samsung Electronics
Samsung Electronics
Copying.
En
d
En
d
Replace Scanning Unit Assy
Yes
Copying.
No
Check the CCD's
flat cable was
connected well
Reference Information
7.6.16 Images at 1 Copy
Service Manual
7-21
Reference Information
7-22
Re- Copying
Replace Scanning Unit Assy
Check if the Scan Glass
was broken
7.6.17 Glass Broken
Service Manual
Samsung Electronics
Samsung Electronics
Check if rolling
sound can be
heard
When start the
Yes
Because It is accaused by the defects of ADF motor or ADF
board,
Replace ADF Engine Assy
No
Yes
No
Check if ADF is
pulling Document
Replace ADF Rubber Pad
Error Messasge is
disappeared?
Yes
No
Because It is accaused by the defects of ADF Sensor ,
Replace ADF Engine Assy
Yes, still there is Error Message
No, just for copying job with ADF
Check if there is
[Document Jam]
message regardless of
removing the
document from ADF
t
Fix the
problem
Replace Main PCBA Controller Board
Reference Information
7.6.18 Document Jam
Service Manual
7-23
Reference Information
7.7 Parts Life Cycle Maintenance Table
7.7.1 Parts Life Cycle Maintenance Table
Supplies
Life Cycle
Condition
Toner Cartridge
4K : For Product Toner Low
Warning
Ready Low Toner -
10% Remains
10K : For Sale
Warning
Ready Toner
-
Initialized at toner change
Toner Empty
Engine Codition LCD Indication
Custmoer Panel Responding
Manage
Toner uninstalled
Fuser
80K(page) :
Simplex
Exhauseted
No Indication
No Indication
Replaced at
Exhauseted
Transer Roller
70K(page) :
Simplex
Exhauseted
No Indication
No Indication
Replaced at
Exhauseted
PickUP Roller
150K(page) :
Simplex
Exhauseted
No Indication
No Indication
Replaced at
Exhauseted
7.7.2 Toner Cartridge Criterion
1) Supplies Criterion (Toner Cartridge)
1. Cartridge Main Defects
- White Point, Black Point : White or Black point on printing image
- Image contamination : Dirty printing image
- Image Fainted : Entire Image is fainted and vertical white line emerge
- Black Line : Vertical black line emerge on printing image
2) Defect Symptoms
7-24
Symptoms
Criterion
Remarks
White, Black Point
Clean Up OPC (10 times), if disappeared, no failure.
- If continuous, failure
System Setup ->
Maintenance-> Clean Drum
Image contamination
(Toner leakage)
Drity printing image or conteminated reverse side
- Clean up OPC (10 times) and inside of machine with cloth, if disappeared, no failure.
Image Fainted
After shake cartridge right and left 5~6 times, if printing image is not fainted, no failure.
(Toner Exhausted)
Vertical Black Line
Vertical thin line emerge, if cartridge is scratched.
- (Customer fault)
Service Manual
Samsung Electronics
Reference Information
7.8 Model Information
7.8.1 Model List
Model Name
classification
Information
ML-3471NDK
Basic Model (PCL+Duplex+Network)
33PPM Mono Laser Printer, PCL6, PS3
ML-3470DK
Network Eliminated Model(PCL+Duplex)
ML-3471NDKG
Network model for business selling (PCL+Duplex+Network)
ML-3470DKG
Netwrork eliminated model for business selling(PCL+Duplex)
ML-3470A
4K Toner Cartridge
Initially installed
ML-3470B
10K Toner Cartridge
Installed for sales
7.8.2 Understanding for Model Code
Model code is inscribed and managed by product standard operation.
If understand the standard operation. It will help to comprehend basic and derived model.
Classification
Model abbriviation
DIGIT
1
2
Example
M
L
Definition
Product Classification
Color
Product
Code
Description
Printer
Class of
Product
Description
:M
Default =
Omissoin.
Only color
printer
“C” initial
.Engine = E
Laser
Beginning
letter of
printer
Description:
L
3
Feature/Properties
4
5
6
7
8
9
10
-
3
4
7
1
N
D
Division
between
code
1. Speed of Engine
- If same speed models
are released
simultaneously higher
model is added +1 at
speed code.
- If over 10 models with
same speed are brought
into, tenth model is
added +1.
2. Domestic Entry Model
Distribution
- C&C : Engine speed
- Information : The first
number deleted
Description
Alphabet
-
Main feature Space
description (Basic:Omitt
- N : N/W
2.Series
ed)
model divi- - P : PS
sion
- S : N/W+PS
- Below 4th - B : Bluetooth
2.Valuablet
grade
- T : 2nd CST
model division
project
- M : Mac
in market
.PC Bundle
Compatible
despite of not .Domestic
- X : Scanner
over 3rd grade distribution . Beside
- VE model, etc. (Entry model abovefeature
(Valuable model excepted)
description,
is decided
product
byproduct
conception
planning group
to product
with sales
planning
prospect)
group
responsed
1.New model,
series model
division
- Over 3rd grade
project
Digit
1. Basic : 0
Alphabet
Service Manual
Samsung Electronics
7-25
Reference Information
7.8.3 Understanding Material Code & Name
Material code and name is maintained by standard criteria.
If understand the criteria, it will help to order materials.
1. Two different description ways for material code. (
: Digit,
: Letter(Alphabet))
ex) 2007-007961 R-CHIP
- Type 1
- Type 2
ex)JB96-01268A ELA UNIT-COVER TOP
Type 1 : Parts managed by entire divisions : Materials used by all samsung products.
Most electrical parts are under the type 1.
Type 2 : Parts managed by a division : Material used by a certain product
Most mechanical parts are under type 2.
2. A/S Only material : Only for A/S, not related to product manufacturing.
3. Ass'y material : More than two materials are assembled. If the material order is out of service, the order can be
processed by Ass'y material order.
Picture and numbers are also described on Service manual.
Ass'y Material and A/S Only material Code are recognizable by product name.
Those are under type 2 and known by material properties and beginning letters of product name.
Classification
Material Code
Material Name
A/S Only Material
**81-******(JB81-00039A)
AS-*****(AS-FUSE)
A/S Only Material
**75-******(JB75-00068A)
MEC-*****(MEC-CHUTE)
A/S Only Material
**92-******(JB92-01131A)
PBA-*****(PBA MAIN-CONTROLLER)
A/S Only Material
**96-******(JB96-01268A)
ELA-*****(ELA UNIT-COVER TOP)
A/S Only Material
**97-******(JB97-01089A)
MEA-*****(MEA UNIT-PULLEY IDLE)
7.8.4 F/W Upgrade Method
If F/W needs Upgrade, F/W file and usbprn file are requested.
Check "Ready" condition with power ON.
1. Paralle cable case
• Start Download Rom file with "copy/b b255_706.fls lpt1:" commend on Dos Mode.
• Once Download are finished, "Reset Printer" is indicated on LCD window.
• Download finished Power ON/OFF.
2. USB cable case (Save attached file at certain directory)
• Start Download Rom file "usbprbs b255_706.fls" on Dos Mode and push the enter key.
• Once Download are finished, "Reset Printer" is indicated on LCD window.
• Download finished Power ON/OFF.
7-26
Service Manual
Samsung Electronics