hf 200w all mode transceiver mark-v ft-1000mp

HF 200W ALL MODE TRANSCEIVER
MARK-V
FT-1000MP
Building on the tremendous success of the FT-1000D and FT-1000MP
Elite-Class HF Transceivers, the MARK-V brings five exciting new
developments in amateur radio technology.
I. 200 WATTS PEP TRANSMITTER OUTPUT
■
Conservatively-Designed 200 W MOSFET Final Amplifier
The MARK-V utilizes a pair of Philips BLF147 Power
MOSFETs in a 30-Volt, push-pull configuration.
These 300-Watt (150-Watt x 2) transistors are run well
below their maximum ratings, ensuring high reliability
and excellent signal purity. The time-proven Low-Pass
Filter network, adopted from the FT-1000D, effectively
suppresses harmonic energy while efficiently delivering
at least 200 Watts to the antenna jack.
■
High-Speed Automatic Antenna Tuner
The basic circuitry from the widely-acclaimed Automatic
Antenna Tuner of the FT-1000MP has been beefed
up for operation at the 200-Watt level for incorporation
in the MARK-V. Constructed on a glass-epoxy circuit
board for maximum efficiency, the Automatic Antenna
Tuner’ s dedicated microprocessor utilizes a complex
analysis algorithm
which permits lightning
-quick matching of
impedance mismatches.
The result : more
power delivered to
the antenna, and less
time wasted in tuning!
200-Watt Automatic Antenna Tuner
■
Philips MOS FET BLF147 / MOS FET BLF145
Revolutionary Heat Sink Design for Contest
and DX-pedition Environments
Providing 200 Watts of momentary output from a
compact transceiver enclosure is easy; creating an HF
II. CLASS-A PA OPERATION: WORLD PREMIERE BY YAESU!
■
Uniquely-Pure Signal Quality, Only from Yaesu!
The MARK-V is the first commercially-designed
Amateur transceiver to provide Class-A operation for
its power amplifier. When engaged by the front panel’ s
[CLASS A] switch, the PA bias is changed dramatically,
and the MARK-V then puts out a 75-Watt signal envelope
of astounding purity. During Class-A operation, 3rd-
powerhouse that will pump out full power for days at
a time is tough! Yaesu’ s engineers, seeking to fulfill
the needs of both contest and DX-pedition operators,
have crafted an all-new, highly-efficient " T-configuration "
heat sink for the MARK-V, providing double the heatdissipating surface area and 2.5 times the cooling capacity
of the heat sink on the FT-1000D! When the going
gets tough, the thermostatically-controlled cross-flow
fan engages at 40 C
ducting the heat across
the dissipating fins and
away from the case. This
revolutionary new heat
sink design ensures
that the MARK-V will
not let you down, even
under the aggressive
operating circumstances
of an expedition to a
rare tropical island!
order Intermodulation Distortion (IMD) drops from a
typical value of -31 dB to -50 dB or better, and 5thand higher-order IMD (the kind which contributes to
"splatter" reports) will drop to the -80 dB range! No
Amateur transceiver has ever approached this degree
of linearity in its power amplifier circuitry. And while
the MARK-V’ s Class-A feature does not directly
Separate FP-29 Switching-Regulator Power Supply
T-Configuration Heat Sink
affect your linear
amplifier’s performance,
the extremely clean
drive to your linear will
result in dramatically
cleaner overall signal
reproduction. Be ready
for other stations to
say, "Wow! Your rig
sounds great!"
Class A 75W PEP IMD
So as to provide the 30 Volts required by the BLF147 MOSFET PA transistors, as
well as the 13.8 Volts required by other transceiver circuitry, Yaesu’ s engineers
have developed the FP-29 External Power Supply especially for the MARK-V.
The external power supply concept significantly reduces the weight of the transceiver
enclosure itself, providing greater safety when shipping the MARK-V to a DXpedition site. The FP-29 is designed with a total output capability of 450 Watts,
with a switching noise suppression of greater than 100 dB, all from an enclosure
measuring just 4.2" (W) x 5.4" (H) x 13.0" (D) (approx. 106 x 136 x 331 mm ). If
you like, you can place the FP-29 on a shelf under your operating desk, and enjoy
the compact size of the MARK-V even more!
Class AB 200W PEP IMD
III. IDBT: INTERLOCKED DIGITAL BANDWIDTH TRACKING SYSTEM
Interlocked Digital Bandwidth Alignment Technique
■
the IF passband width and center frequency. With
IDBT, the DSP filter is automatically re-programmed
so as to match the custom bandwidth you just set,
and the DSP filter then contributes a filtering slope
which resembles a sheer cliff! The results? The
incredible selectivity of an all-DSP system with the
protection of the DSP afforded by the extensive IF
analog filtering. What’ s more, the potential for AGC
"pumping" caused by different analog and digital
bandwidths is eliminated; thus, the need for separate
analog and DSP AGC systems is also gone, eliminating
The MARK-V introduces a unique and formidable
interference-fighting system with the development of
IDBT, whereby the bandwidth of the Digital Signal
Processing filter is automatically locked to be the
same as the net bandwidth of the analog IF filters.
Engaging the IDBT, the operator experiences a sudden
sharpening of the shape factor of the receiver’ s filter
system. The analog IF, which utilizes cascaded crystal
and/or mechanical filters, includes both IF WIDTH
and IF SHIFT controls, which allow modification of
70.455 MHz
RF AGC
RF
FRONT END
8.215 MHz
1st
MIX
LPF
2nd IF
FILTER
2nd
MIX
M CF
IF
AMP
455 kHz
2.4kHz
1st
LOCAL
2.4kHz
4th
MIX
10.24 kHz
IF
AMP
A/ D
3rd
LOCAL
2nd
LOCAL
EDSP
AGC
DET
3rd IF
FILTER
3rd
MIX
the very real danger of annoying cross-AGC artifacts
which can seriously degrade receiver performance.
New to the 455 kHz analog IF is a 10-Pole Collins Mechanical SSB Filter, providing outstanding voice
signal reproduction along with enhanced skirt selectivity
compared to the FT-1000MP’ s 8-pole filter.
The IDBT function is controlled by an allocation of
up to 60 kbytes of ROM in the Main CPU, while the
DSP performance utilizes 1 Mbyte of EEPROM!
This perfect blending of the analog and digital worlds
brings you, today’ s Elite-Class operator, the most
crunch-proof receiver filtering ever!
EDSP
DET
2.4kHz
D/ A
To
AF AMP
EDSP
BPF
4th
LOCAL
CPU
IDBT: A Breakthrough in Selectivity!
SHIFT
WIDTH
IDBT BLOCK DIAGRAM
■
IV. VARIABLE RF FRONT-END FILTER
VRF Preselector Filtering Protects Receiver Front End (160M ~ 20M)
■
Extending the protection afforded the sensitive frontend components of the receiver, Yaesu’ s engineers
have developed the VRF module: a High-Q input
"Preselector" filter ahead of all active devices in the
front end, including the main bandpass filters! Particularly
in multi-operator contest or DX-pedition environments,
where large low-band antennas may be in close proximity,
a receiver operating (for example) on 20 meters can
suffer intermodulation interference from on-site 40- and
80-meter signals, compounded by extremely strong
7 MHz broadcast signals. The ANT
VRF
ATT
VRF circuit provides narrowband selectivity which prevents
this unwanted signal voltage
from hitting the input side of the
bandpass filter switching diodes,
VRF CONTROL
where 2nd-order IMD is most
often created in an HF receiver. Tuning of the VRF is
incredibly simple: just turn the VRF/MEM CH knob,
and peak the background noise or signal strength!
The VRF is stoutly designed, with large (10 mm x 10
mm) coils yielding high Q, and precision tuning
capacitors ensuring that performance does not degrade
over time. A total of 31 tuning memories per band
allow very quick QSY, and the use of high-quality,
shielded relays for VRF selection ensures that nothing
in the VRF can itself contribute IMD.
0.1~ 1.8MHz
LPF
LPF
1.8~30MHz
HPF
IPO ON
RF AMP
1st
MIX
RF AGC
LPF
1st
LOCAL
BPF
VRF/FRONT END BLOCK DIAGRAM
V. ENHANCED ERGONOMICS: MULTI-FUNCTION SHUTTLE JOG DIAL
Quick Access to VRF and IDBT via Shuttle Jog Tuning Ring
■
The immensely-popular Shuttle Jog tuning ring, which
is concentric with the Main Tuning Knob, has a new
look in the MARK-V: it now includes the activation
switches for the VRF (left side)
Receiver Front End Highlights
The MARK-V adopts the low-noise front end design
of the FT-1000MP. Two low-noise Junction FET
preamplifiers are provided, one in a "tuned" configuration
with optimized gain and noise figure independently
for the high and low bands, with the other "flat"
preamp providing a wide, uniform-gain response. The
first mixer utilizes a quad of SST-310 Junction FETs
in a doubly-balanced circuit, resulting in wide dynamic
range. Eleven bandpass filter networks provide input
protection for the front end, working in concert with
the VRF to provide the best-ever 2nd-order IMD
prevention in an Amateur transceiver.
and IDBT (right side) features, so the operator does
not have to move his hand position to activate these
important circuits during contest or pile-up situations!
Superb Ergonomics Across the Front Panel
■
Both the Main and Sub VFO Tuning Knobs are larger,
allowing silky-smooth tuning even if you have large
fingers! The right side
VRF Features Large, High-Q
Coils and High-Quality Relays
VRF Typical Bandpass Response (3.5 MHz)
of the front panel contains the adjustment controls for
the VRF, IDBT, NOTCH, and CLARIFIER, conveniently
grouped so you can get at them quickly. For contest
or DX-pedition use, you cannot afford to lose even
milliseconds in search of a frequently-used control.
And the most popular
EDSP functions from the
FT-1000MP are now much
easier to use! The CW Audio
Peaking Filter (with
bandwidths of 60, 120,
and 240 Hz) and the fourposition EDSP Noise
Reduction (NR) feature Access VRF and IDBT Features via Shuttle Jog Dial
are conveniently located
just to the left of the Main
Tuning Dial, for quick,
convenient push-button
access. Right next to the
APF and NR controls are
the three EDSP response
Contour selections, which
enhance signal-to-noise ratio
by matching the DSP
frequency response to the
unique
shape of the
incoming signal envelope.
Large-diameter control knobs
make precise adjustments easy!
HF 200W ALL MODE TRANSCEIVER
MARK-V
FT-1000MP
The development of an Elite-Class HF Transceiver is not accomplished in a vacuum.
It is a team effort, drawing on the unique abilities of Yaesu' s Research and Development experts,
our most senior HF Design Engineers, and extensively utilizing the comments
and recommendations of hundreds of DX and contest operators.
Today' s bands demand leading-edge features,
and the MARK-V is without peer when it comes to performance and innovation.
MKR(250):1.555kHz
1500Hz
A : MAG
1400Hz
1710Hz
ENHANCED DIGITAL SIGNAL
PROCESSING
OUTPUT:
0.0dBm
1420Hz
1210Hz
Acclaimed by DX operators worldwide for its wideranging capabilities, Yaesu' s Enhanced Digital
Signal Processing (EDSP) circuitry is a key component
in the system-wide
filtering effort which
stretches from the
antenna ports to the
microphone or speaker.
DATA BPF Performance
SWT:
230s
-6dB
IRG:
0dBm
RBW:
10Hz
FAX
SSTV
PKT
RTTY-LO
RTTY-HI
Speech Processor provides a clean increase in average
power output, through a carefully-designed envelope
compression technique proved so successful in the
FT-1000MP.
Microphone Equalizer Performance
MKR(250):312.53Hz
A : MAG
OUTPUT: 0.0dBm
VBW:
100Hz
SWT:
230s
DRG:
400ms
IRG:
0dBm
TX-EQ3
TX-EQ4
START : 10Hz
RBW:
3Hz
STOP : 3.1kHz
VBW:
10Hz
TX-EQ2
■
EDSP Unit
■
Highly-Effective Digital Noise Reduction Circuit
Utilizing mathematical algorithms developed after
thousands of hours of on-the-air evaluation, the EDSP
Noise Reduction provides four different Noise Reduction
patters, to allow you to cope with changing noise conditions.
The algorithms utilized in the development of the
EDSP Noise Reduction cover the vast majority o f
noise patterns encountered on the HF bands.
Digital Noise Reduction Performance
MKR(250):1.555kHz
A MAG
OUTPUT
Selectable SSB Pattern-Contour Filters
Particularly effective in enhancing signal-to-noise
ratio and intelligence recovery
on SSB signals, the Contour
selections include High-Cut,
Low-Cut, and Mid-Cut responses,
with a color-coded indicator
aiding in filter selection.
Choose the one that causers
the incoming voice to "pop"
out of the background noise!
SWT
230s
MKR(250):312.53Hz
A : MAG
IRG
0dBm
RX-3
OUTPUT: 0.0dBm
SWT:
230s
RX-2
RBW
10Hz
RX-1
VBW
100Hz
STOP : 10kHz
STOP:3.1kHz
Optimized Narrow-Bandwidth Filters for CW
and Data Modes
For razor-sharp selectivity under marginal conditions,
the EDSP CW Audio Peaking Filter provides bandwidths
of 60, 120, or 240 Hz. Filter selection is accomplished
using a convenient pushbutton switch on the left side
of the front panel.
CW APF Performance
PMFIR Log Magnitude
10
0
CWF 240
-10
-20
CWF 120
-30
-40
-50
RBW:
3Hz
DRG:
400ms
START : 10Hz
■
IRG:
-20dBm
VBW:
10Hz
DRG
400ms
START:10Hz
CWF 060
-60
■
Selectable Digital Modulation/Demodulation
Among EDSP’ s more advanced technology are the
digital Modulator and Demodulator circuits. On transmit,
the EDSP Modulator provides improved transmitter
signal-to-noise ratio, very flat frequency response, and
a choice of four cutoff frequencies (100, 150, 200, or
300 Hz) on the low-frequency side (high-frequency
cutoff: 3100 Hz). Whether you’ re rag-chewing or in a
DX contest, the MARK-V provides a frequency
response that’ s ideal for you!
Providing a boundary for the receiver’ s SSB bandwidth
within the EDSP, you can select either 100-3100 Hz
or 300-2800 Hz filters in the EDSP Demodulator circuit,
which provides very low noise with no odd DSP artifacts
or distortion.
■ Digital
STOP : 10kHz
Auto-Notch
The DSP Auto-Notch seeks out and reduces or eliminates
annoying "beat" signals that can ruin reception. Especially
effective when used in a "combined" mode with the
455 kHz IF Notch (which typically provides rejection
in excess of 70 dB!), the Digital Auto-Notch is a tremendous
aid in providing operator comfort during long operating
sessions.
DUAL RECEIVE WITH
INDEPENDENT AGC SYSTEMS
■ Listen
to Two Frequencies Simultaneously
with No AGC Interaction!
On some "Dual Receive" transceivers, the AGC corresponding
to the signals present on the "Main" frequency affect
what’ s happening on the "secondary" frequency (which
can cause a signal to disappear on the 2nd frequency!).
The MARK-V utilizes two completely independent
receivers, each with its own IF filter(s) and AGC loops,
so that you can listen to two frequencies (on the same
band) simultaneously with no interaction.
The audio levels for the two receivers may be adjusted
independently, of course, and you can select either
"Stereo", "Mixed" (partially combined), or "Monaural"
(fully combined) audio for your headphones. And the
AF-REV switch allows the functions of the AF GAIN
(Main) and the SUB AF volume controls to be reversed,
if desired.
Ideal for contest operation (for watching for "multipliers")
or for DX pile-up use (for monitoring both sides of
the pile-up), the MARK-V’s Dual Receive system
ensures that you’ re always on top of the action!
MAIN
RECEIVER
LEVEL
POTENTIOMETER
ANTENNA
-70
-80
■
-90
-100
TX-EQ1
START : 10Hz
0.0dBm
CONTOUR Performance
NR OFF
NR A NR C
NR B NR D
DRG:
400ms
FREQUENCY kHz
Besides the CW Audio Peaking Filter, specially-designed
and optimized digital-mode filters are provided, for
maximum data throughput on RTTY, Packet, SSTV,
PSK31, or FAX.
Digital SSB Microphone Equalizer &
RF Speech Processor
Similar in concept to the "Contour" feature used on
receive, one of the four different microphone equalization
filters may be engaged so as to provide the most effective,
penetrating audio "punch" for your voice and microphone.
Working to enhance "talk power" even more, the RF
ATT
BPF
RF
AMP
HYBRID
TRANSFORMER
MIX
AF
AMP
SUB
RECEIVER
SPEAKER
HEADPHONES
LEVEL
POTENTIOMETER
AF OUT
DUAL RECEIVE BLOCK DIAGRAM
As the world enters a new millennium,
new chapter in the history books, with
Photo shows optional MD-100A8X Deluxe Desk Microphone
■
■ Easy-Acce ss
"SPLIT" Operation
When seconds count in a DX pile-up, the convenience
of the MARK-V’s "SPLIT" operating mode can’t be
beat! The "RX" (green) and "TX" (red) LEDs above the
Main and Sub VFO tuning dials are actually combination
LED/Switches; pressing the Sub VFO’s "TX" LED
automatically shifts the transmitter to control by the
Sub VFO, with receiver control still on the Main
VFO. Pressing the Sub VFO’s "RX" LED activates
Dual Receive, so you’re listening on both VFOs,
while transmitting on the Sub VFO. It’s easy, it’s
intuitive, and it’s quick!
INDUSTRY-LEADING RF FRONT
END DESIGN
DX-pedition and Contest operators alike have
acclaimed the strong-signal performance
and antenna selection convenience of the
FT-1000D/FT-1000MP. This legacy is
renewed in the MARK-V FT-1000MP!
Two TX/RX Antenna Ports plus Receive-only
Antenna Line Jacks
ANTENNA SWITCHING
ANT A ANT B
RX ON
RX OFF
The "A" and "B" antenna jacks allow connection of
different antennas, which may be selected using the
front panel’s A/ B switch. The antenna selected on
a particular VFO/memory and band will be preserved
in that VFO or memory register, and will be automatically
recalled when you return to that VFO or memory. The RX
"In" and "Out" jacks allow connection of a Beverage
or loop receiving antenna, and may also be used to
connect a special receive-line filter, if desired.
■
Three RF Preamplifier Modes plus IPO
(Direct Mixer Feed)
The wide variations in noise and signal levels on the
HF bands demand a customized approach to receiver
front end gain. The MARK-V provides separate, optimized
preamplifiers for the Low (7 MHz and below), Mid
(10 ~ 21 MHz), and High (24.89 MHz and up) HF
bands. If front end preamplification is not needed,
pressing the IPO (Intercept Point Optimization)
button will bypass the RF preamp stage, routing the
RF energy directly to the first mixer, and increasing
the 3rd-order
Intercept Point
accordingly.
TX
RX
RX ONLY ANTENNA
FIX ANT JACK
IN
OUT
EXT RCVR
FILTER OR
PREAMP
■
Four-Level Input RF Attenuator
For fine-tuning the front-end gain, or for comfortable
listening to extremely strong local signals, the Attenuator
circuit provides 6/12/18 dB of gain reduction (plus "Off").
■
RF GAIN Control
For precise setting of the background noise level, or
for modifying the receiver’ s AGC threshold, the front
panel’ s RF GAIN control is conveniently located on
the same shaft as the main receiver’ s AF GAIN control.
■
AUTO-AGC
For ease in operation, the "AUTO" AGC mode provides
mode-specific selection of the receiver recovery time
for the Automatic Gain Control system. Manual selections
of FAST, SLOW, and OFF are also provided.
Yaesu is proud to turn the page to an exciting
the release of the MARK-V FT-1000MP!
HF 200W ALL MODE TRANSCEIVER
MARK-V
FT-1000MP
IF Filter Bandwidth Selections
OUTSTANDING IF FILTER CHAIN
■ Factory-installed IF Filter Selections
Yaesu’s hybrid Analog/DSP IF design reflects
our commitment to bring you the toughest,
most QRM-resistant receiver possible!
■
(NAR1)
NOR
BAND
WIDTH
(NAR2)
3rd IF
(455kHz)
2nd IF
(8.2MHz)
3rd IF
(455kHz)
2nd IF
(8.2MHz)
3rd IF
(455kHz)
MODE
SSB
2.4kHz
2.4kHz
2.4kHz
2.4kHz
-
-
SSB
CW
2.4kHz
2.4kHz
500Hz
2.4kHz
-
-
CW
AM
THRU
6.0kHz
2.4kHz
2.4kHz
-
-
AM
RTTY
PKT
2.4kHz
2.4kHz
-
-
500Hz
2.4kHz
RTTY
PKT
(LSB)
NAR1
(NOR)
2nd IF
(8.2MHz)
MODE
Carefully-Specified 8.2 MHz and 455 kHz IF Filters
■ IF Filter Selections with All Options Installed
NAR2
NAR1
(NOR)
Both 2.4 kHz and 500 Hz 8-pole crystal filters for the
2nd (8.2 MHz) IF are factory installed, and the 455 kHz
(3rd) IF includes a 10-pole Collins Mechanical SSB
Filter. Optional filters are available at bandwidths of
2.0 kHz or 250 Hz (2nd and 3rd IFs), and 500 Hz (3rd IF
and Sub Receiver). The outstanding shape factors of
these filters combine with the IDBT digital filtering
to provide brick-wall selectivity with outstanding
close-in performance.
■
NOR
BAND
WIDTH
(LSB)
2nd IF
(8.2MHz)
3rd IF
(455kHz)
2nd IF
(8.2MHz)
THRU
6.0kHz
2.4kHz
2.0kHz
2.0kHz
(YF-114SN) (YF-110SN)
500Hz
THRU
6.0kHz
2.4kHz
2.0kHz
2.0kHz
500Hz
(YF-114SN) (YF-110SN)
NAR2
(NAR1)
3rd IF
(455kHz)
(NAR2)
2nd IF
(8.2MHz)
3rd IF
(455kHz)
2.0kHz
2.0kHz
(YF-114SN) (YF-110SN)
500Hz
250Hz
250Hz
(YF-115C) (YF-114CN) (YF-110CN)
2.0kHz
2.0kHz
2.4kHz
(YF-114SN) (YF-110SN)
2.4kHz
500Hz
250Hz
250Hz
(YF-115C) (YF-114CN) (YF-110CN)
※On FM, the Bandwidth switches are disabled.
IF Notch Filter Performance
PMFIR Log Magnitude
10
0
-10
-20
-30
-40
455 kHz IF NOTCH features Improved Rejection
-50
-60
The newly-designed 455 kHz IF Notch Filter provides
improved beat rejection, typically 50 dB or more. Use
the front-panel NOTCH control to adjust the exact
position of the Notch.
The MARK-V may be configured (via the convenient
Menu system) to engage both the manual IF Notch Filter
and the DSP Auto-Notch Filter, allowing cascaded
Analog/Digital Notch Filtering. Say "Good-bye" to
irritating beatnotes forever!
New 10-pole Collins Mechanical SSB Filter Passband Response
■
Dual-Mode IF Noise Blanker
The adjustable IF Noise Blanker may be configured
for optimum blanking of (A) narrow-pulse ignition-type
noises, or (B) wide-pulse over-the-horizon radar systems.
■ Synchronous
AM Detection for Reduced Fading
The "Synchronous" detection technique provides improved
AM reception by significantly reducing fading. The
-70
-80
-90
-100
FREQUENCY kHz
incoming signal is removed, reception is converted to
SSB, and a non-fading carrier is re-inserted, thereby
eliminating the chief cause of fading. A Synchronous
Tuning Scale on the display assists in the tuning process.
CW FEATURES FOR OPERATORS
DEMANDING THE BEST
CW Full Break-in and Electronic Keyer
■
The ultra-fast response time of the Direct Digital
Synthesizer (DDS) allows full break-in (QSK) operation,
without perceptible character truncation. The built-in
electronic keyer features separate Dot:Space and
Dash:Space weight settings, and the receiver recovery
time during semi-break-in work may be set optimally
for CW, independently from the SSB "VOX Delay"
setting.
CW Spot
■
Align yourself precisely with the station being worked
by the DX
station in a
pile-up.
CW Pitch
■
Select filter center frequency, TX offset, and
Sidetone pitch over the range 300-1050 Hz, and use
the SPOT switch to zero in on the other station.
■
CW Reverse Tuning
Choose either USB- or LSB-side injection to combat
interference, or to switch a station from SSB to CW
without guesswork as to the operating frequency!
■
CW Tuning Indicator
Provides visual confirmation of precise tuning on receive.
■
Multi-Function Display with Improved Contrast
The MARK-V’ s multi-function display provides a
wealth of transceiver status in a conveniently-arranged
layout, and it boasts improved contrast compared to
previous designs. The area around the Main VFO
frequency display contains the most-often-used
information, such as Clarifier Offset, VRF Tuning
Scale, Antenna
Tuner status, and
VF O / Memory
status.
■
High-Resolution DDS Provides Silky-Smooth Tuning
Yaesu pioneered the use of the DDS (Direct Digital
Synthesizer) in modern HF transceivers, and the MARK-V’ s
DDS system is the latest, greatest evolution of this
design technique. The DDS provides ultra-fine tuning
steps as small as 0.625 Hz,
ideal for the slow tuning
needed for HF digital work.
And the very low noise of
the DDS-based local oscillator
system yields a very low
noise floor during reception
and transmission.
■
Enhanced Shuttle Jog™ Tuning Dial
Instantly popular on the original FT-1000MP, the Shuttle
Jog dial, concentric with the Main VFO tuning dial,
is a spring-loaded center-off tuning aid which allows
the operator to make progressively larger scans up and
down the band by "leaning" on the Shuttle Jog to the
left or right. A slight displacement of the dial causes
tuning in 10 Hz steps, and full rotation of the dial to
the left or right yields steps as large as 100 kHz per
step-you’ ll watch the Megahertz fly by if you need to
QSY quickly! The Shuttle Jog tuning speed may be
adjusted via the Menu system, so you can set it up
just the way you want it! And with the addition of the
VRF and IDBT On/Off switches on the Shuttle Jog
ring, you’ ll find little need for your hand from the
central area of the transceiver during critical moments!
TM
TM
TM
■
Two Key Jacks
Front- and rear-panel paralleled KEY jacks allow easy
connection to paddles, external electronic keyers, or
computer-driven keying interfaces.
■
Electronic Memory Keyer
Use the optional FH-1 Remote Keypad (or build your
own keypad) to activate the onboard electronic message
memory keyer. Four messages of up to 50 characters
each may be programmed, and an incrementing contest
number may also be imbedded into a recorded message.
CONVENIENCE FEATURES FOR
WORLD-CLASS HF OPERATORS
The FT-1000D and FT-1000MP were
universally acclaimed, not only for
their industry-leading RF and IF
innovations, but also for the wealth of
operating conveniences made available to
demanding HF operators. The MARK-V
FT-1000MP builds on this tradition, and
makes it even better!
■ Unmatched
Ergonomic Front Panel Design Concept
Owners of Yaesu’ s FT-1000 family of Elite-Class
transceivers use them under the most stressful conditions.
Over long hours of operation, the carefully designed
front-panel ergonomics are a profound asset for the
operator, whether on a DX-pedition on a faraway island or
at home at 4 o’ clock in the morning. Borrowing extensively
from the FT-1000MP front panel layout, the MARK-V
features larger knobs, reduction in the total knob/button
count, and enhanced ease of operation as a result of
the intensive ergonomic system analysis applied by
Yaesu’ s engineers. This effort, coupled with feedback
from users like you, has resulted in an incredibly
complex transceiver also being incredibly easy to use!
TM
■
Direct Keypad Frequency Entry;
Twin Stacked VFO Registers
The convenient 10-key direct frequency entry keypad
provides instant frequency setting anywhere within the
range of the transceiver. The "Band" keys on the keypad
also provide one-touch band change, and the two VFOs
available per amateur band allow one VFO to be set for the
CW segment, and the other for the phone segment, with the
mode, bandwidth, and antenna selections for each segment
being automatically memorized into each VFO register.
■
Extensive Memory System, including
5-Channel Quick Memory Bank (QMB)
The MARK-V provides 99 regular memory channels,
five QMB memories, and nine "band limit" memories.
The "regular" memories may be assigned into one of
five memory "groups", for
convenience in recalling of the
memories. Besides the operating
frequency, memory channels store
operating mode, antenna selection,
Clarifier offset (if any), IF filter
selection, and repeater shift status
(if applicable).
■
Versatile Scanning Capability
The acclaimed scanning features of the MARK-V
include a number of capabilities which make HF
operation a breeze. These include:
●Memory/VFO Scan: Scan the memories, or scan the
band, with the scanning speed being adjustable, via
Menu, independently for Memory and VFO Scan. An
Auto-Write feature allows "busy" channels to be written
into memory automatically, if desired.
●Memory Channel "Skip" Scanning: You can "flag"
certain memories to be skipped during scanning, so
the transceiver is not constantly halting on constantlybusy frequencies like WWV.
●Programmable Memory Scan (PMS): You may use
and scanning. For example, within the 18.0-18.5 MHz
range, you may limit operation to the range 18.068
to 18.168 MHz, to prevent accidental excursions
outside the amateur band segment.
■
Easy Digital-Mode Interfacing
The exciting world of digital mode operation is more
popular than ever! And the MARK-V is unmatched
in its ease of interfacing, whether you’ re interested in
PSK-31, RTTY, Packet, SSTV, or Fax. Dedicated
rear-panel FSK and AFSK jacks make cabling a
breeze, and customized EDSP and IF filter selections
make sure that you’ re never forced to use a non-optimal
bandwidth during digital operation.
VRF/MEM Channel Selector
The VRF/MEM Channel Selector knob, located in the
upper right-hand corner of the front panel, also functions
as a VFO Channel Selector for quick and easy QSY in
user-programmer steps of 1 to 100 kHz. Use 1 kHz to
5 kHz steps for cruising up and down the band, or 50 kHz
steps for general-coverage frequency hopping. A simple
press on this control restores VRF (Preselector)
operation, and you’ ll be ready for action!
■
■
Feature Customization Menu
For configuration of the MARK-V just the way you want
it, many "set and forget" features and functions may be
customized via the Menu system. The Menu provides
access to the settings for a number of operating parameters
which are not needed during everyday operation; the
use of the Menu technique significantly reduces the
total number of knobs and switches on the front panel,
making long hours of operation even more enjoyable.
■
Built-in Temperature-Compensated
Reference Oscillator
The TCXO-4 Temperature-Compensated Reference
Oscillator, which was an extra-cost option on the
original FT-1000MP, is built into every MARK-V.
The TCXO-4 provides frequency accuracy of 0.5 ppm
at 25 C, and 2.0 ppm over the temperature range -10 C to
+50 C. For ultra-precise
frequency accuracy,
the optional TCXO-6
provides accuracy of
0.25 ppm at 25 C,
and 0.5 ppm at -10 C
to +50 C.
AND SO MUCH MORE
General Coverage Reception: 100 kHz ~ 30 MHz.
Large, high-quality speaker (3-5/8" / 92 mm) for
better receive audio clarity. ●Two headphone jacks:
one each 6 and 3.5 mm. ●Adjustable "Beep" tone for
keypad keys. ●Adjustable torque for tuning knobs. ●
Built-in VOX. ●FAST tuning key for quick
frequency change. ●Built-in RS-232C level converter
for easy computer interfacing.
●
●
SPECIFICATIONS
General
Transmitter
RX Frequency Range : 100 kHz ~ 30 MHz
TX Frequency Ranges : 160 ~10 m (Amateur bands only)
Frequency Stability
: ± 0.5 ppm (after 1 min. @ 25 C)
± 0.25 ppm
(after 1 min. @ 25 C, w/TCXO-6)
Operating Temperature Range: -10 C ~ +50 C
Emission Modes : LSB, USB, CW, FSK, AFSK, AM, FM
Frequency Steps : 0.625/1.25/2.5/5/10 Hz for
SSB,CW, RTTY & Packet
100 Hz for AM and FM
Antenna Impedance : 16.6~150 Ohms, unbalanced
(Tuner ON, TX only)
Power Consumption : 13.8 VDC 30 VDC
RX (no signal) 2.3 A
–
RX (signal)
2.7 A
–
TX (200 W)
2.2 A
14.5 A
Supply Voltage
: 30 VDC and 13.8 VDC (FP-29)
Dimensions (WHD)
: 16 "x 5.3 "x 13.7 "
(410 x 135 x 347 mm)
Weight (approx.)
: 31 lbs. (14 kg.)
Receiver
Power Output
: Adjustable up to 200 watts
(50 watts AM carrier),
Class A mode (SSB) : 75 watts maximum
Duty Cycle : 100% @ 100 watts,
50% @ 200 watts (FM & RTTY, 3-minute TX)
Modulation Types: SSB: J3E Balanced,
AM: A3E Low-level (early stage),
FM: F3E Variable reactance,
AFSK : J1D, J2D Audio frequency shift keying
Maximum FM Deviation: ± 2.5 kHz
FSK Shift Frequencies: 170, 425, and 850 Hz
Packet Shift Frequencies : 200 and 1000 Hz
Harmonic Radiation : Better than -60 dB (Typical)
SSB Carrier Suppression: At least 40 dB below peak output
Undesired Sideband Suppression: At least 55 dB below peak output
Audio Response (SSB): Not more than -6 dB
from 400 to 2600 Hz
3rd-order IMD: - 31 dB @ 200 watts PEP, or better
(Class A mode) - 50 dB @ 75 watts PEP (Typical)
Microphone Impedance: 500 to 600 Ohms
Circuit Type : Quad-conversion superheterodyne
(triple conversion for FM)
Intermediate Frequencies:
Main RX; 70.455 MHz/8.215 MHz/455 kHz,
Sub RX; 47.21 MHz/455 kHz
0.5 - 1.8 MHz 1.8 - 30 MHz
Sensitivity :
Modes
SSB/CW (2.0 kHz)
2 μV
0.16 μV
AM (6 kHz)
13 μV
2 μV
FM
–
0.5 μV
(with preamp on, IDBT on, SSB/CW/AM for 10 dB S/N,
FM for 12 dB SINAD, 0 dBμ = 1 μV)
Selectivity (-6/-60 dB):
BandWidth
Modes
Min. -6 dB BW Max. -60 dB BW
2.4 kHz all except FM
2.2 kHz
4.2 kHz
2.0 kHz all except FM
1.8 kHz
3.6 kHz
500 Hz
1.8 kHz
500 Hz CW/RTTY/Packet
250 Hz
700 Hz
250 Hz CW/RTTY/Packet
AM (Wide)
4 kHz
14 kHz
FM
8 kHz
19 kHz
IF Rejection (1.8 ~ 30 MHz):
80 dB or better (Main RX), 60 dB or better (Sub Rx)
Image Rejection (1.8 ~ 30 MHz):
80 dB or better (Main), 50 dB or better (Sub)
Maximum Audio Output:
2.0 W into 4 Ohms with <10 %
THD
FP-29 Specifications
DC Output Voltage/Current: +30 V: 15 A; +13.8 V: 3 A
Input Voltage
: AC 100-120 V, 50-60 Hz
AC 200-240 V, 50-60 Hz
Current Consumption (Approx.): AC 100-120 V: 9 A, AC 200-240 V: 5 A
Operating Temperature Range: -10 C~ +50 C
Case Size (W x H x D):4.2 "x 5.3 " x 13 " (106 x 135.5 x 331 mm)
Weight (Approx.): 7 lbs.(3.2 kg.)
Specifications are subject to change, in the interest of technical
improvement, without notice or obligation.
OPTIONAL ACCESSORIES
Linear Amplifier/48 Volts DC Power Supply
/
Desktop Microphone
MD-100A8X
Hand Microphone
MH-31B8
Digital Voice Recorder
DVS- 2
Remote Control Keypad
FH-1
2nd IF (8.2 MHz) Filters
3rd IF (455 kHz) Filters
SSB 2.0 kHz X'tal Filter
YF-110SN
SSB 2.0 kHz X'tal Filter
YF-114SN
CW 250 Hz X'tal Filter
YF-110CN
CW 250 Hz X'tal Filter
YF-114CN
Lightweight
Stereo Headphone
YH-77STA
Temperature
Compensated X'tal
TCXO-6
CW 500 Hz Filter
(Collins R Mechanical Filter)
YF-115C
* For Main Rcvr and 2nd IF Sub Rcvr
External Speaker w/Audio Filters
SP-8
LL-7 Phone Patch Option
About this brochure: we have made this brochure as comprehensive and factual as possible. We reserve the right, however, to make changes at any time in equipment, optional accessories,
specifications, model numbers, and availability. Some accessories shown herein may not be available in some countries. Some information may have been updated since the time of printing;
please check with your Authorized Yaesu Dealer for complete details.
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-ku, Tokyo 153-8644, Japan
For the latest Yaesu news,visit us on the Internet:
http://www.vxstdusa.com
http://www.yaesu.co.uk
VERTEX STANDARD
Phone 562/404-2700; Fax 562/404-1210
Email:amateursales@vxstdusa.com
US Headquarters
17210 Edwards Road, Cerritos, CA 90703, U.S.A.
International Division
8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525 1118 ZN, Schiphol The Netherlands
YAESU UK LTD.
Email: sales@yaesu.co.uk
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
2000.06NS
B9200290 Printed in Japan
Unit 5, 20 /F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong