Broan RM60000 SERIES User manual

Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
at
:: rangehoods . com
B
Y
B
R
O
A
N
-
N
U
T
O
N
E
RM60000 SERIES
RANGE HOOD
INSTALLATION INSTRUCTIONS
AND USER MANUAL
HB0026
RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGE 11.
V05527 rev B
Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
!
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
WARNING
!
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSON(S)
OBSERVE THE FOLLOWING:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer at the address or
telephone number listed in the warranty.
Before servicing or cleaning unit, switch
power off at service panel and lock
service disconnecting means to prevent
power from being switched on accidentally.
When the service disconnecting means
cannot be locked, securely fasten a
prominent warning device, such as a tag,
to the service panel.
Installation work and electrical wiring
must be done by qualified personnel in
accordance with all applicable codes and
standards, including fire-rated construction
codes and standards.
Sufficient air is needed for proper combustion
and exhausting of gases through the
flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating
equipment manufacturer’s guidelines
and safety standards such as those
published by the National Fire
Protection Association (NFPA), and the
American
Society
for
Heating,
Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local
code authorities.
When cutting or drilling into wall or ceiling,
do not damage electrical wiring and
other hidden utilities.
Ducted fans must always be vented to
the outdoors.
Do not use this range hood with any
additional solid-state speed control
device.
To reduce the risk of fire, use only steel
ductwork.
This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
Never leave surface units unattended at
high settings. Boilovers cause smoking
and greasy spillovers that may ignite.
Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high
heat or when cooking flaming foods.
c) Clean ventilating fans frequently. Grease
should not be allowed to accumulate on
fan or filter.
d) Use proper pan size. Always use cookware
appropriate for the size of the surface
element.
WARNING
TO REDUCE THE RISK OF INJURY TO
PERSON(S) IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting
lid, cookie sheet, or metal tray, then turn off
the burner. BE CAREFUL TO PREVENT
BURNS. IF THE FLAMES DO NOT GO
OUT IMMEDIATELY, EVACUATE AND
CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN –
You may be burned.
3. DO NOT USE WATER, including wet
dishcloths or towels – This could cause
a violent steam explosion.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC
extinguisher and you know how to
operate it.
B. The fire is small and contained in the
area where it started.
C. The fire department has been called.
D. You can fight the fire with your back
to an exit.
* Based on “Kitchen Fire Safety Tips”
published by NFPA.
CAUTION
1.
2.
3.
4.
5.
6.
a)
7.
8.
For general ventilating use only. Do not
use to exhaust hazardous or explosive
materials and vapors.
To avoid motor bearing damage and noisy
and/or unbalanced impellers, keep drywall
spray, construction dust, etc. off power unit.
Your hood motor has a thermal overload
which will automatically shut off the motor if
it becomes overheated.The motor will restart
when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
For best capture of cooking impurities, the
bottom of the hood should be a minimum
of 24” and a maximum of 30” above the
cooking surface.
Please read specification label on product
for further information and requirements.
To reduce the risk of fire and to properly
exhaust air on a ducted installation, be
sure to duct air outside – Do not exhaust
air into spaces within walls or ceiling or
into attics, crawl spaces, or garage.
This product is equipped with a thermostat
which may start blower automatically. To
reduce the risk of injury and to prevent
power from being switched on accidentally,
switch power off at service panel and
lock or tag service panel.
The RM60000 Series hood must be
installed with blower models RM325H,
RM326H, 331H, 332H, 335 or 336 only.
Other blowers cannot be substituted.
(Blowers sold separately.)
-2Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
TABLE OF CONTENTS
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
12.0
13.0
14.0
15.0
16.0
17.0
SELECT BLOWER OPTION AND INSTALL DUCTWORK . .5
MEASURE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . .6
PREPARE THE INSTALLATION . . . . . . . . . . . . . . . . . . . . . .6
INSTALL BACKSPLASH . . . . . . . . . . . . . . . . . . . . . . . . . . .7
INSTALL WOOD MOUNTING STRIP . . . . . . . . . . . . . . . . . .7
INSTALL THE HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
INSTALL TRANSITION TO ROUGH-IN PLATE . . . . . . . . . .8
INSTALL THE ROUGH-IN PLATE TO THE HOOD . . . . . .8-9
INSTALL THE OPTIONAL SOFFIT CHIMNEY . . . . . . . . . . .9
INSTALL BLOWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
INSTALL LIGHT BULBS AND WARMING LAMPS . . . . . . . .9
INSTALL FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
USE AND CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SERVICE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
-3Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
Wall & Roof
Caps, Ext.
Blowers
MODEL 331H
MODEL 335
MODEL 437 MODEL 441
(600 cfm) OR (1200 cfm) OR (High Capacity
(10” Rd.
332H (900 cfm) 336 (1500 cfm)
Wall Cap)
Roof Cap)
(Exterior Blower) (Exterior Blower)
MODEL 647
(7” Rd.
Wall Cap)
MODEL 634
OR 644
(Roof Cap)
Elbows &
In-Line
Dampers
MODEL 418
(10” Rd. Adjustable Elbow)
MODEL 421
(10” Rd. Vert.
In-Line Damper)
MODEL 415
(7” Rd. Adjustable Elbow)
Ductwork
MODEL 407
(7” Rd. Duct - 2 ft. sections)
MODEL 410
(10” Rd. Duct - 2 ft. sections)
Choose 1 of
5 Discharge
Transitions
MODEL 424
MODEL 454
MODEL 427
MODEL 423
MODEL 453
(41/2” x 181/2” (41/2” x 181/2” to (41/2” x 181/2” to (41/2” x 181/2” to (41/2” x 181/2” to
10” Rd. to 10” Rd., 6” 10” Rd. - vertical) 10” Rd. - horiz.
10” Rd. - horiz. /
horiz. / right)
high - lateral)
front / rear)
left)
OPTIONAL SOFFIT
CHIMNEY
RMN SERIES
ROUGH-IN KIT
MODEL 332KR
(Use with all
Exterior Blower
models: 331H,
332H, 335, 336)
Choose 1 of 3
Blower Systems
B
Y
B
R
O
MODEL RM325H
BLOWER / ROUGH-IN KIT
(600 cfm Interior Blower &
Rough-in Plate)
RM60000
SERIES
HOOD
(Canopy with
OPTIONAL
blower controls
BAFFLE
& lighting.
FILTERS
Required for all
RBF SERIES
installations.)
MODEL RM326H
BLOWER / ROUGH-IN KIT
(1200 cfm Interior Blower &
Rough-in Plate)
A
N
-
N
U
T
O
N
E
RMP SERIES BACKSPLASH
(Stainless Steel wall covering
with warming shelves. Optional)
RM60000 SERIES
RANGE HOOD SYSTEM
-4Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
1. SELECT BLOWER OPTION AND INSTALL DUCTWORK
Either an interior or exterior blower may be used with this hood. The RM60000
Series hood must be installed with blower models RM325H, RM326H, 331H,
332H, 335 or 336 only. Other blowers cannot be substituted. (Blowers sold separately).
NOTES:1. The 331H, 332H, 335 or 336 exterior blower MUST BE installed with the
rough-in kit model 332KR (sold separately).
2. In addition to the blower models listed above, this hood is also compatible
with older internal blower versions 325H ans 326H. However, discard
the installation instructions included with those blowers and and contact
our technical suppport to obtain replacement instruction.
Plan where and how the ductwork will be located.
Install proper-sized ductwork, transition(s), elbow(s), and roof or wall cap for the
type of blower you are using.
ROOF CAP
7" (178 mm)
ROUND DUCT
DECORATIVE
12"
FLUE (305 mm)
or SOFFIT
WALL CAP
HOOD
7" (178 mm)
ROUND
ELBOW
24" TO 30" (609 to 762 mm)
ABOVE COOKING SURFACE
ROOF CAP
HH0024A
MODEL RM325H SINGLE BLOWER
TYPICAL DUCTWORK
10" (254 mm)
ROUND DUCT
WALL CAP
12"
DECORATIVE
FLUE (305 mm)
or SOFFIT
4-1/2" x 18-1/2"
to 10"
(114 x 470 to
254 mm) ROUND
TRANSITION
(see page 4)
HOOD
24" TO 30" (609 to 762 mm)
ABOVE COOKING SURFACE
EXTERIOR BLOWER
HH0025A
MODEL RM326H DUAL BLOWER
TYPICAL DUCTWORK
10" (254 mm)
ROUND DUCT
DECORATIVE
12"
FLUE
or SOFFIT (305 mm)
10" (254 mm)
ROUND ELBOW
EXTERIOR
BLOWER
HOOD
332KR
ROUGH-IN KIT
(see page 4)
24" TO 30" (609 to 762 mm)
ABOVE COOKING SURFACE
HH0026A
MODEL 331H, 332H, 335 OR 336 EXT.
BLOWER TYPICAL DUCTWORK
-5Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
2. MEASURE INSTALLATION
Dimensions for the most common installations are shown below.
Adjust your measurements for various heights of ceilings, soffits, cabinets or
cooktops. For proper operation, the hood must be a minimum of 24" and a
maximum of 30" above the cooktop.
Standard
8 ft. (2.44 m)
ceiling
Standard 18"
(457 mm) H
over-cooktop
cabinet
18"
(457 mm)
19"
(483 mm)
Top of wood
mounting strip
Hood
RMP Series
Backsplash
(optional)
Maximum distance
between the hood and
the cooktop
24"
(610 mm)
Minimum distance
between the hood and
the cooktop
Standard 36"
(914 mm)
H cooktop HH0028A
Cooktop
INSTALLATION WITH 12’’ SOFFIT OR
OPTIONAL SOFFIT CHIMNEY RMN SERIES
INSTALLATION WITH STANDARD 18’’ HIGH
OVER-COOKTOP CABINET
3. PREPARE THE INSTALLATION
Remove the installation kit from inside the hood.
Make sure that the following items are included:
-Wood strip
-Installation manual
-Accessories including:
.Filters (Quantity varies depending on range hood width)
.Bag of parts including:
Screws #10-2" flat head (4),Screws #8-3/4" (8), Nuts #10-32 (4)
Wall anchors (2), Washers 3/16" ID X 3/4" OD (2)
Using a Phillips #2 or a
Robertson #2 screwdriver,
unscrew the hood from the
bottom of crate. Refer to figure
beside to locate all 4 screws.
Discard these screws and
remove hood from wood pallet.
3
4
1
2
HR0002
-6Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
4. INSTALL BACKSPLASH
(OPTIONAL) RMP Series
Backsplash must be installed before the hood shell because the hood shell covers
the backsplash top mounting screws. In order to be able to install the backsplash,
make sure you have at least 18” (457 mm) clearance between bottom of hood and
range control panel or cooktop. (Refer to instructions included with backsplash.)
5. INSTALL WOOD MOUNTING STRIP
Measure and mark a level line on wall above cooktop location for the wood mounting strip
(see illustration below and under step 2). Use #10 - 2” flat head screws to secure the
mounting strip to the drywall. Make sure to hit the wall studs. (See figure below.)
CAUTION
Due to the weight of this hood, ensure that the wood strip is attached to all of
the available wall studs (2 studs minimum for the 30” hood, more as hood
width increases); not into the drywall alone.
1. Drywall
2. Wood Mounting Strip
3. Flat Head Screw
4. Wall Anchor Location
5. Outline of the Back of the Hood
6. Wall Studs
6. INSTALL THE HOOD
Rest the back cavity of the hood on the wood mounting strip.
CAUTION
Hold the hood until it is completely secured to the wood mounting strip.
Secure hood to wood strip
with (4) screws #8 - 3/4” (for
30” and 36” width hoods) or
(6) screws (for 42” width
and wider hoods) provided
at locations shown. Drill (2)
3/16” size holes into the
drywall for wall anchors
through the existing holes in
the inside hood back in the
locations shown. Then install
the two wall anchors and
attach the hood to these
anchors with the remaining
#8 - 3/4” screws and the
(2) washers provided.
Top of hood (inside view)
Mounting Screw Locations
Wall Anchor Locations
HD0064
-7Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
7. INSTALL TRANSITION TO ROUGH-IN PLATE
Model 423, 424, 427, 453, or 454
Attach transition (if required) to blower rough-in plate.
Use duct tape to make all joints secure and air-tight.
NOTE: Model RM325H blower plate connects directly to 7" round ductwork without a
transition.
Exterior blower models utilize a model 332KR rough-in plate which connects
directly to 10” round ductwork without a transition.
HD0049
8. INSTALL THE ROUGH-IN PLATE TO THE HOOD
Run power cable to installation location. Refer to the instructions included with the
selected blower or rough-in kit (sold separately) for details on installing the rough-in
plate. Install the rough-in plate so that the wiring box is located on the right side
as you are facing the hood.
For ducting through back of hood, remove existing plate from inside back of hood
and attach to inside top of hood to cover hole. Secure to threaded studs with same
(4) nuts.
For ducting through top of hood, existing plate remains in place on inside back of
hood.
2
1. Locknuts
2. Plate on top of
hood
3. Rough-in plate on
back of hood
4. Wiring Cover
1
1
4
3
1
1
HD0063
Connect ducting to transition or rough-in plate as you are installing the rough-in
plate. Use duct tape to make all joints secure and air-tight.
-8Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
8. INSTALL THE ROUGH-IN PLATE TO THE HOOD (CONT’D)
Wiring
!
WARNING
Risk of electrical shock. Electrical wiring must be done by qualified
personnel in accordance with all applicable codes and standards. Before
connecting wires, switch power off at service panel and lock service
disconnecting means to prevent power from being switched on accidentally.
Remove wiring cover from rough-in plate and set aside.
Remove appropriate knockout from rough-in plate. As you are installing the
rough-in plate, feed 6” of power cable through knockout opening and attach
cable to wiring box with appropriate connector.
Connect wires as shown in blower instructions.
Reinstall wiring cover.
9. INSTALL THE OPTIONAL SOFFIT CHIMNEY
(OPTIONAL) RMN Series
Refer to the instructions included with the soffit chimney.
10. INSTALL BLOWER
Refer to instructions included with blower.
Once the blower is installed, plug the blower unit into the female receptacle and
the power supply onto the male connector inside the hood. DO NOT plug the two
cords into each other.
HE0003
11. INSTALL LIGHT BULBS AND WARMING LAMPS
Install (2) heat lamp bulbs. Use BR40 size, 250W Max., infrared bulbs only
(purchase separately).
Install (3) halogen light bulbs. Use PAR20 50W Size (purchase separately).
-9Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
12. INSTALL FILTERS
CAUTION
Remove protective plastic film covering filters before installing them.
It is recommended to install side filters first and finish with center one(s).
1. Insert upper end of filter into the hood (finger sized cup side).
2. Raise lower end toward the inside of hood.
3. Position rear part of filter into channel and pull.
4. Using finger sized cup, pull on the upper end of filter and slide it under the
front inner retaining piece.
1
2
4
3
HD0024
HD0065
Replacement filters are available from your dealer. See label inside hood for size
and part number.
Baffle Filters
Baffle filters are available as an option. To order them, refer to the table below to
find the right filter kit number for your hood. To install them, refer to instruction
sheet included with baffle filter kit.
HD0011
KIT #
HOOD WIDTH
RBF6030
RBF6036
RBF6042
RBF6048
RBF6054
RBF6060
RBF6066
RBF6072
30”
36”
42”
48”
54”
60”
66”
72”
BAFFLE FILTER (TYPICAL)
- 10 Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
13. USE AND CARE
Grease Filters
The grease filters should be cleaned frequently. Use a warm detergent solution.
Grease filters are dishwasher safe. Wash more often if our cooking style generates
greater grease - like frying foods or wok cooking.
Remove filters by pushing filters towards the back of hood and rotating filters downward.
Blower Cleaning
Remove the filters in order to access the blower. Vacuum blower to clean. Do not
immerse in water. Refer to blower instruction manual for more details.
Grease Rail
The grease rail should be cleaned
frequently, especially if baffle filters
are used.
Remove filters, then, disassemble the
grease rail from the hood by removing
its 3 retaining screws. See illustration
beside.
HD0069
Refer to stainless steel cleaning in Hood Cleaning section below. Once the grease
rail is clean and dry, reassemble it to the hood and reinstall filters.
Hood Cleaning
Stainless steel cleaning: How to maintain its « BRIGHT LOOK »
Do:
- Regularly wash surfaces with clean cloth or rag soaked with warm water and mild
soap or liquid dish detergent.
- Always clean in the direction of original polish lines.
- Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.
- You may also use a specialized household stainless steel cleaner.
Don’t:
- Do not use any steel or stainless steel wool or any other scrapers to remove
stubborn dirt.
- Do not use any harsh or abrasive cleansers.
- Do not allow dirt to accumulate.
- Do not let plaster dust or any other construction residues reach the hood.
During construction/renovation, cover the hood to make sure no dust sticks to
stainless steel surface.
Avoid: when choosing a detergent
- Any cleaners that contain bleach will attack stainless steel.
- Any products containing : chloride, fluoride, iodide, bromide will deteriorate
surfaces rapidly.
- Any combustible products used for cleaning such as acetone, alcohol, ether,
benzol, etc., are highly explosive and should not be used close to a range.
Enamel finish:
Clean with warm water and mild detergent only. When discoloration occurs, use a
good enamel polish such as automotive polish. (DO NOT use rough abrasive
cleaner or porcelain cleaner.)
- 11 Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
14. OPERATION
Always turn ON your hood before you begin cooking in order to establish an air
flow in the kitchen. Let the blower run for a few minutes to clear the air after you
turn off the range. This will help keep the whole kitchen cleaner and brighter.
4
6
5
3
3
1
3
1
2
1. Warming lamps
2. Warming lamp switches
3. Halogen lights
4. Halogen light switches
5. ON/OFF Blower switch
6. Blower speed control
Warming lamps (Infrared)
Each warming lamp (item 1 in picture above) is controlled with is own ON/OFF
switch (item 2 on picture above).
Use only BR40 Size, 250W Max., Infrared bulbs. (Purchase separately)
!
WARNING
Do not place highly flammable material on warming shelves.
Cooktop Lighting (Halogen)
A double set of ON/OFF switches (item 4 on picture above) control the halogen
lights (item 3 on picture above).
The front rocker controls the center light. The rear rocker controls both side lights.
Select one, two, or three lights for best cooktop lighting.
Use PAR 20, 50W halogen bulbs. (Purchase separately)
Blower
The blower is operated using two (2) controls.
Use the red, lighted ON/OFF switch (item 5 on picture above) to start and stop the
blower. When turned on, the blower will operate at the previous setting of the
speed control (item 6 on picture above).
Turn the speed control knob clockwise to decrease blower speed counterclockwise to increase speed.
HEAT SENTRY™
Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a
device that will turn on or speed up the blower if it senses excessive heat above
the cooking surface.
1) If blower is OFF - it turns blower ON to HIGH speed.
2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed.
When the temperature level drops to normal, the blower will return to its original setting.
!
WARNING
The HEAT SENTRY™ thermostat can start the blower even if the hood is
turned OFF. When this occurs, it is impossible to turn the blower OFF with
the switch. If you must stop the blower, do it from the main electrical panel.
- 12 Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
15. WIRING DIAGRAM
RIGHT HEAT LAMP SWITCH
120V 60HZ
B
IN
TO FAN MOTOR
RIGHT HEAT LAMP SOCKET
W
B
B
B
W
G
HS
B
SPEED
THERMOSTAT
NEMA
5-15P
W
FAN SWITCH
B
CONTROL
RIGHT LIGHT
PLUG
SOCKET
W
B
W
B
LIGHTS SWITCH
B
CENTER LIGHT SOCKET
W
B
LEFT LIGHT SOCKET
B
LEFT
B
W
HEAT LAMP SWITCH
LEFT HEAT LAMP SOCKET
B
W
TERMINAL BLOCK
W
W
W
W
W
W
W
- 13 Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
16. SERVICE PARTS
1
20
21
19
17
11
14
13
12
18
16
20
3
4
6
8
15
7
7
2
HL0031
22
5
9
10
2
- 14 Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
16. SERVICE PARTS (CONT’D)
KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
12
‡
‡
‡
13
14
15
16
17
17
17
17
18
18
18
18
18
18
18
18
19
20
21
22
‡
‡
‡
‡*
PART
NUMBER
V03493
V02264
V02773
V02772
V03435
V03436
V02563
V03502
V03503
V03504
V03501
V03505
V03517
V03519
V03520
V00673
V02512
V01869
V01582
V05522
V05523
V05524
V05525
V14763
V14764
V14765
V14766
V14767
V14768
V14769
V14770
V05528
V05521
V14744
V14745
V05527
V12971
V02544
QTY (HOOD WIDTH)
30” 36” 42” 48” 54” 60” 66” 72”
DESCRIPTION
Rangemaster Logo
Socket Lamp
Male Connector
Female Connector
Thermostat
Thermostat Bracket
SPST Single Switch for Warming Lamps
SPST Double Switch for Halogen Lights
SPST Lighted Single Switch for Blower
Speed Control Button
Speed Controller
Terminal strip
10” Power Cord
10” Control Wire
10” Lighted Switch Wire
Lock-Nut 8-32
Screw 8-32 x 1/2 Quadrex
Machine Screw 8-32 x 1/4
Lock nut 6-32
Sq. Perf. Grille Filter 9.5 x 15.25 x 0.355
Sq. Perf. Grille Filter 11.61 x 15.25 x 0.355
Sq. Perf. Grille Filter 13.61 x 15.25 x 0.355
Sq. Perf. Grille Filt. 17.525 x 15.25 x 0.355
Grease Rail 30”
Grease Rail 36”
Grease Rail 42”
Grease Rail 48”
Grease Rail 54”
Grease Rail 60”
Grease Rail 66”
Grease Rail 72”
Filter Spring 5.265” x 0.350”
Sealing Extrusion 20.625”
Left Side Liner
Right Side Liner
Installation Guide
Parts Bag (Flat head screws #10 x 2” (4),
1
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
3
1
3
2
1
1
1
1
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
3
1
3
2
1
1
1
1
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
3
1
3
2
1
1
1
1
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
4
1
4
2
1
1
1
1
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
3
1
3
2
1
1
1
1
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
5
1
5
2
1
1
1
1
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
2
3
1
5
2
1
1
1
1
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
4
1
4
2
1
1
1
Screws #8 x 3/4” (8), Nuts #10-32 (4).
Wall anchors (2), Washers 3/16” ID x 3/4” OD (2))
1
1
1
1
1
1
1
1
Halogen Lamp PAR20 50W
Warming Lamp BR40, 250W max.
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
‡ Not shown.
* Purchase locally.
- 15 Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D
:: rangehoods . com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
17. WARRANTY
BROAN-NUTONE ONE YEAR LIMITED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products that
such products will be free from defects in materials or workmanship for a period of
one year from the date of original purchase. THERE ARE NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace,
without charge, any product or part which is found to be defective under normal
use and service.
This warranty does not cover (a) normal maintenance and service or (b) any
products or parts which have been subject to misuse, negligence, accident,
improper maintenance or repair (other than by Broan-NuTone), faulty installation
or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified
for the express warranty. Some states and /or provinces do not allow limitation on
how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S
OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY
UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF
OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states
and/or provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state, or province to anoter. This warranty supersedes all
prior warranties.
To qualify for warranty service, you must (a) notify the company at the address
or telephone number below, (b) give the model number and part identification and
(c) describe the nature of any defect in the product or part. At the time of requesting
warranty service, you must present evidence of the original purchase date.
In case of discrepancies between the english version and the french and or spanish
version of this warranty, the english version will prevail.
- 16 Broan at :: rangehoods . com is a division of
kitchen :: accessories
U
N
L
I
M
I
T
E
D