INTERNATIONAL DESIGN GUIDE
CONTENTS
Wolf Built-In Ovens
4
Wolf Electric Cooktops
9
Wolf Gas Cooktops
14
Wolf Integrated Modules
19
Wolf Warming Drawers
30
Wolf Dual Fuel Ranges
34
Wolf Sealed Burner Rangetops 40
Wolf Gas Ranges
46
Wolf Gas Rangetops
53
Wolf Cooktop Ventilation
57
Wolf Ventilation
Recommendations
67
Features and specifications indicated
herein and on our website are subject
to change at any time without notice.
Check our website, wolfappliance.com
for the most up-to-date specifications.
IMPORTANT NOTE
As you follow these instructions, you
will notice warning and caution symbols.
This blocked information is important
for the safe and efficient installation of
Wolf equipment. There are two types of
potential hazards that may occur during
installation.
signals a situation where minor
injury or product damage may occur
if you do not follow instructions.
states a hazard that may cause
serious injury or death if precautions
are not followed.
WOLF ® is a registered trademark of Wolf Appliance, Inc.
Another footnote we would like to
identify is IMPORTANT NOTE: This
highlights information that is especially
relevant to a problem-free installation.
WELCOME TO WOLF APPLIANCE
In this Design Guide, you’ll find all the necessary
information for specifying a Wolf oven, cooktop,
range, rangetop or ventilation equipment into the
next kitchen or home you design.
Each unit is handcrafted with the knowledge and
experience gleaned from being the premier
supplier of cooking equipment to professional
chefs and their restaurants for nearly 75 years.
Sub-Zero, a corporate companion and kitchen
soul mate, shares the identical values and pride
we take in providing the best cooking equipment.
A Wolf is beautiful and will complement any
design you use, whether it be contemporary or
traditional.
But that’s not why many customers turn to us.
We have a passion for cooking and it shows in
our work. Consumers appreciate the unique
features we have built in to our many different
models. You can refer to specifics as you page
through this guide.
The features are as numerous as the various
units you have to choose from. But one of the
more prominent highlights is the Wolf Dual
Convection System that is in all our built-in
ovens and dual fuel ranges. It delivers even
temperature and airflow throughout the oven.
Its combination of fans and heating elements
operate either simultaneously or in sequence,
depending on which of the ten different cooking
modes your client chooses.
Our electric cooktops are unique to the industry
with their capabilities of providing simmer on
all elements and the melt feature on one of the
elements. The triple element on the 914 mm
cooktop can generate up to 2,700 watts for
those large pots that need fast boiling.
If you are looking for cooking performance,
but don’t want to shout it out in your kitchen
design, one of our unframed electric cooktops
may be your choice. There’s no stainless steel
trim, just the sophisticated black ceramic glass
top that can be mounted flush with the top of
the countertop or as a frameless installation
sitting on top of the countertop surface.
The sizes, alternative tops, and selection of the
standard classic stainless steel and the premium
finishes of carbon or platinum stainless steel
make your decision-making process much more
fun for you and your clients. Now you can give
them exactly what they want without sacrificing
the quality they demand.
In all your applications you can depend on Wolf.
That reputation is even stronger because it is
backed by Sub-Zero. The combination of the two
is really greater than their sum.
Review this Design Guide in greater detail
when you get a chance and keep it as a handy
reference. We are confident you will like what
you see.
In addition, our dual-stacked burners on the gas
cooktops, dual fuel ranges and sealed burner
rangetops are all sealed and offer you the capability of simmering foods.
3
B U I LT- I N O V E N S
Model ISO30U/S
Model ISO36U/S
W O L F L S E R I E S B U I LT- I N O V E N S
FEATURES
It’s hard to put into a few words the differences
you will see in the Wolf L Series ovens compared
to others on the market. Some of those differences are very dramatic. Did you notice that the
control panel closes? It’s an attractive feature
and will enable you to hide that control panel
that many of us have labored to make functional
and tried to make beautiful.
Dual convection logic control system
Inside, the beauty, design and functionality
continue. Brilliant halogen lights illuminate the
beautiful blue interior. As you open the oven
door, feel the smoothness of the door damper
system. Pull that bottom oven rack all the way
out and notice how it is nestled on the door
rails. With the dual convection fans, all models
offer ten different cooking modes.
Three removable racks, six-level rack guide and
full-extension bottom rack—five-level rack guide
for 914 mm oven
Ten cooking modes—bake, roast, broil, convection bake, convection roast, convection broil,
convection, bake stone (accessory required),
proof and dehydrate (accessory required)
Rotating glass touch control panel
Cobalt blue porcelain oven interior
Large viewing triple-pane window
Dual interior halogen lighting
Hidden bake element and recessed broil element
Temperature probe and receptacle
Self-clean, delayed start and Sabbath features
Door hinge with hydraulic damper assures
smooth opening and closing of the door
Model IDO30U/S
Factory-installed trim
This appliance is certified by Star-K
to meet strict religious regulations in
conjunction with specific instructions
found on www.star-k.org.
L S E R I E S O V E N F E AT U R E S
Model ISO30U/S shown
Electronics and
door cooling vents
Rotating electronic
control panel
Recessed broil
element
Oven door light
switch
Thermostat
Location of rating
plate
Three removable
racks
Probe receptacle
Hidden bake
element
Halogen lights
Door hinge with
hydraulic damper
Exhaust vent
Removable
six-level rack guide
4
Triple-pane window
Gasket
B U I LT- I N O V E N S
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
There are only three different sizes to consider
when planning for your layout. You can choose
either a 762 mm or 914 mm built-in single oven
or a 762 mm double oven.
International (I) models come with a factory
installed transformer and require a 220-240
V AC, 50/60 Hz electrical supply, fused at the
correct rating for the unit. The appropriate electrical connection must be provided in accordance
with local requirements.
For ease of installation, Wolf recommends using
838 mm wide cabinets with 762 mm ovens and
991 mm wide cabinets with the 914 mm oven.
You will need a minimum 610 mm of usable
cabinet depth. The cabinet must be able to
support 113 kg for a single oven and 181 kg for
a double oven.
Wolf built-in ovens have a face trim on all four
sides and will overlap stiles and rails. The trim
overlaps 3 mm on the bottom, 5 mm on the top
and 19 mm on each side.
Specifications on the following pages provide
overall dimensions, rough openings and installation specifics for the three different oven sizes.
We have minimized the information contained
in the illustrations, concentrating on the critical
information you need to plan your installation.
IMPORTANT NOTE: Unless you are using
cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in an
adjacent cabinet within reach of the conduit. A
51 mm diameter hole to route the conduit
through cabinetry will be required. Refer to the
Installation Specifications illustrations on the
following pages for location of the electrical
supply.
You must follow all local codes and ordinances
when installing your service.
A Wolf single oven may be installed below an
electric or gas cooktop. Wolf built-in ovens are
designed and agency approved for installation
with Wolf cooktops only. Refer to the electric
and gas cooktops sections for additional
specifications. A built-in oven cannot be installed
below a Wolf rangetop.
MODEL OPTIONS
Built-In Ovens
762 mm Single Oven – Unframed
Classic Stainless
ISO30U/S
This appliance must be installed in accordance with
local codes. The correct voltage, frequency and
amperage must be supplied to the appliance from a
dedicated, grounded circuit that is protected by a
properly sized circuit breaker or time delay fuse.
The proper voltage, frequency and amperage ratings
are listed on the product rating plate.
914 mm Single Oven – Unframed
Classic Stainless
ISO36U/S
762 mm Double Oven – Unframed
Classic Stainless
IDO30U/S
ACCESSORIES
Built-In Ovens
Bake stone accessory, includes
stone, rack and peel
Additional oven racks
Two-piece broiler pan and
temperature probe
Dehydration racks with door
stop
Accessories are available through
your Wolf dealer.
5
B U I LT- I N O V E N S
OVERALL DIMENSIONS
762 mm Built-In Single Oven
MODEL OPTIONS
Unframed / Classic
32 mm
TOP VIEW
RIGHT SIDE VIEW
762 mm Built-In Single Oven
48 mm
CONDUIT
CHANNEL
ISO30U/S
662 mm
699 mm
610 mm
INSIDE
SIDE TRIM
S P E C I F I C AT I O N S
716 mm
48 mm
762 mm Built-In Single Oven
759 mm
Overall Dimensions
(W x H x D)
759 mm x 699 mm
x 610 mm
Door Clearance
527 mm
Overall Oven
Interior Capacity
127 L
Overall Interior Dim
(W x H x D)
635 mm x 419 mm
x 483 mm
Usable Interior Dim
(W x H x D)
546 mm x 419 mm
x 416 mm
Cabinet Width
838 mm rec
762 mm min
Cabinet Depth
610 mm min
Min Base Support
113 kg
Opening Width
724 mm
Opening Height
691 mm
Trim Overlaps
5 mm top
3 mm bottom
19 mm each side
Electrical Supply
1.2 m flexible 4-wire
Electrical Rating
5.1 kW at 240 V
Total Amps
21
Shipping Weight
124 kg
610 mm
BEHIND FRAME
OPEN OVEN DOOR
Unit dimensions may vary to ± 3 mm.
527 mm
711 mm
I N S TA L L AT I O N S P E C I F I C AT I O N S
762 mm Built-In Single Oven
Wall Application
838 mm
RECOMMENDED CABINET WIDTH
762 mm min
610 mm min
OPENING DEPTH
220-240 V AC, 50/60 Hz
30 amp dedicated circuit
Conduit
76 mm
E
724 mm
691 mm
OPENING
HEIGHT
OPENING WIDTH
ELECTRICAL LOCATION
WITHIN OPENING
APPLIES ONLY TO
CABINETS DEEPER
127
THAN 610 mm
mm
102
mm
E
E
E
I N S TA L L AT I O N O P T I O N S
The Wolf 762 mm single oven may be
installed below a Wolf 762 mm electric or
gas cooktop. Unless you are using cabinets
deeper than 610 mm, it is recommended that
the electrical supply be placed in the base
cabinet to the right of the oven within reach
of the conduit. The Wolf 762 mm single oven
may also be installed below a Wolf 914 mm
electric or gas cooktop.
Undercounter Installation
838 mm
RECOMMENDED CABINET WIDTH
762 mm min
The Wolf 762 mm single oven may be
installed in combination with a Wolf warming
drawer.
A Wolf 762 mm single oven may be installed
next to another 762 mm single oven. You
must allow for a 64 mm space between the
oven rough openings. Also, a separate inner
wall is required for each oven between
openings.
Refer to installation instructions shipped with
each Wolf product for detailed specifications.
6
95 mm min
691 mm
OPENING
HEIGHT
127
ELECTRICAL
LOCATION WITHIN mm
OPENING APPLIES
ONLY TO CABINETS
DEEPER THAN 610 mm
E
E
102
mm
914 mm
610 mm min
OPENING DEPTH
STANDARD
FLOOR TO
COUNTER
HEIGHT
724 mm
OPENING WIDTH
121 mm min
IMPORTANT NOTE: Unless you are using cabinets
deeper than 610 mm, it is recommended that the
electrical supply be placed in an adjacent cabinet within
reach of the conduit. Choose the location shown in the
illustrations that best suits your installation.
B U I LT- I N O V E N S
OVERALL DIMENSIONS
914 mm Built-In Single Oven
RIGHT SIDE VIEW
32 mm
TOP VIEW
MODEL OPTIONS
914 mm Built-In Single Oven
48 mm
CONDUIT
CHANNEL
619
mm
Unframed / Classic
584 mm
ISO36U/S
610 mm
INSIDE
SIDE TRIM
48 mm
867 mm
S P E C I F I C AT I O N S
914 mm Built-In Single Oven
905 mm
76
mm
610 mm
BEHIND FRAME
OPEN OVEN DOOR
Unit dimensions may vary to ± 3 mm.
870 mm
I N S TA L L AT I O N S P E C I F I C AT I O N S
914 mm Built-In Single Oven
Wall Application
991 mm
RECOMMENDED CABINET WIDTH
914 mm min
E
451 mm
Overall Dimensions
(W x H x D)
905 mm x 619 mm
x 610 mm
Door Clearance
451 mm
Overall Oven
Interior Capacity
125 L
Overall Interior Dim
(W x H x D)
762 mm x 337 mm
x 483 mm
Usable Interior Dim
(W x H x D)
673 mm x 337 mm
x 416 mm
Cabinet Width
991 mm rec
914 mm min
Cabinet Depth
610 mm min
Min Base Support
113 kg
Opening Width
876 mm
Opening Height
611 mm
Trim Overlaps
5 mm top
3 mm bottom
19 mm each side
Electrical Supply
220-240 V AC, 50/60 Hz
30 amp dedicated circuit
Conduit
.9 m flexible 4-wire
Electrical Rating
5.1 kW at 240 V
Total Amps
21
Shipping Weight
131 kg
876 mm
610 mm min
OPENING DEPTH
611 mm
OPENING
HEIGHT
OPENING WIDTH
ELECTRICAL LOCATION
WITHIN OPENING APPLIES
ONLY TO CABINETS
DEEPER THAN 610 mm
102
mm
127 E
mm
E
E
I N S TA L L AT I O N O P T I O N S
Undercounter Installation
991 mm
RECOMMENDED CABINET WIDTH
914 mm min
95 mm min
611 mm
OPENING
HEIGHT
610 mm min
OPENING DEPTH
ELECTRICAL LOCATION
WITHIN OPENING APPLIES
ONLY TO CABINETS
DEEPER THAN 610 mm
914 mm
STANDARD
FLOOR TO
COUNTER
HEIGHT
127
mm
E
102
mm
E
The Wolf 914 mm single oven may be installed
below a Wolf 914 mm electric or gas cooktop.
Unless you are using cabinets deeper than 610
mm, it is recommended that the electrical
supply be placed in the base cabinet to the
right of the oven within reach of the conduit.
The 914 mm single oven may also be installed
below a Wolf 762 mm framed electric cooktop,
but not below a 762 mm unframed electric
cooktop or 762 mm gas cooktop. When
installed below a cooktop, it is recommended
that the opening for the oven be 197 mm from
the floor to ease the use of the oven door.
The Wolf 914 mm single oven may be installed
above or below a Wolf warming drawer with
integrated drawer front.
876 mm
OPENING WIDTH
197 mm rec
121 mm min
IMPORTANT NOTE: Unless you are using cabinets
deeper than 610 mm, it is recommended that the
electrical supply be placed in an adjacent cabinet within
reach of the conduit. Choose the location shown in the
illustrations that best suits your installation.
A Wolf 914 mm single oven may be installed
directly above another 914 mm oven. You must
allow enough space between the oven rough
openings to accommodate a base support for
the top oven. A 914 mm single oven may be
installed next to another 914 mm oven. You
must allow for a 64 mm space between the
oven rough openings. Also, a separate inner
wall is required for each oven between
openings. Each base cabinet support must be
able to support 113 kg.
7
B U I LT- I N O V E N S
OVERALL DIMENSIONS
762 mm Built-In Double Oven
MODEL OPTIONS
32 mm
TOP VIEW
RIGHT SIDE VIEW
762 mm Built-In Double Oven
48 mm
Unframed / Classic
CONDUIT
CHANNEL
IDO30U/S
610 mm
48 mm
S P E C I F I C AT I O N S
762 mm Built-In Double Oven
Overall Width
759 mm
Overall Height
1270 mm
Overall Depth
610 mm
Door Clearance
527 mm
Overall Oven Interior
Capacity (per oven) 127 L
INSIDE
SIDE TRIM
OPEN OVEN DOOR
711 mm
759 mm
610 mm
76 mm
BEHIND FRAME
Overall Interior Dim
(W x H x D)
635 mm x 419 mm
x 483 mm each
Usable Interior Dim
(W x H x D)
546 mm x 419 mm
x 416 mm each
Cabinet Width
838 mm rec
762 mm min
Cabinet Depth
610 mm min
I N S TA L L AT I O N S P E C I F I C AT I O N S
Min Base Support
181 kg
Opening Width
724 mm
762 mm Built-In Double Oven
Wall Application
Opening Height
1260 mm
Trim Overlaps
5 mm top
3 mm bottom
19 mm each side
Electrical Supply
220-240 V AC, 50/60 Hz
50 amp dedicated circuit
Conduit
1.5 m flexible 4-wire
Electrical Rating
8.9 kW at 240 V
Total Amps
37
Shipping Weight
211 kg
I N S TA L L AT I O N
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
716 mm
1232 mm
1270 mm
Unit dimensions may vary to ± 3 mm.
838 mm
RECOMMENDED CABINET WIDTH
762 mm min
610 mm min
OPENING DEPTH
E
724 mm
1260 mm
OPENING WIDTH
OPENING
HEIGHT
1702 mm
typical
ELECTRICAL LOCATION
WITHIN OPENING
APPLIES ONLY TO
CABINETS DEEPER
127
THAN 610 mm
mm
102
mm
E
E
IMPORTANT NOTE: Unless you are using cabinets
deeper than 610 mm, it is recommended that the
electrical supply be placed in an adjacent cabinet within
reach of the conduit. Choose the location shown in the
illustrations that best suits your installation.
8
E
527 mm
WOLF ELECTRIC COOKTOPS
WOLF FRAMED ELECTRIC COOKTOPS
FEATURES
Behind the sophisticated, minimalist exterior,
beneath that perfectly smooth, subtly patterned
glass that cleverly reduces scratches, there is a
high-performance cooking tool.
Classic stainless steel trim finish
The black ceramic glass top is beautifully
complemented by the classic stainless steel trim.
Multiple cooking elements with different zones
allow your customer a variety of different applications. The 914 mm cooktop features a 305
mm diameter triple heating element—concentric
rings that give you exceptional control of
temperature for pans and pots of every size.
All of the heating elements offer True Simmer,
and with each cooktop there is one element that
enables you to set a temperature for melting.
Easy-to-clean black ceramic glass surface is
resistant to scratching, staining, impact and
heat—translucent surface allows you to see the
glow of hot elements
Illuminated electronic touch controls with
graduated control lighting
Model ICT15E/S
381 mm Framed
Electric Cooktop
Ribbon-type radiant heating elements—some
elements with multiple temperature zones
True Simmer setting on all elements
Melt setting on one element
Hot surface indicators on all elements
High frequency pulsation elements improve
cooking performance and control
Model ICT30E/S
762 mm Framed
Electric Cooktop
Temperature limiter to ensure that safe
operating temperature of ceramic glass is never
exceeded
Child safety lock key and universal off
Model ICT36E/S
914 mm Framed
Electric Cooktop
This appliance is certified by
Star-K to meet strict religious
regulations in conjunction with
specific instructions found on
www.star-k.org.
F R A M E D E L E C T R I C C O O K T O P F E AT U R E S
Model ICT36E/S shown
Triple-zone
element
Illuminated electronic
touch controls
Dual-zone
element
OFF
SIM
SIM
MODEL OPTIONS
H
HIG
ON
E2 3
ZON
E
ZON
OFF
O
H
HIG
OFF
ON
SIM
Framed Electric Cooktops
H
HIG
H
HIG
OFF
ON
OFF
ON
E2
ZON
SIM
H
HIG
ON
OFF
MELT
381 mm Framed Electric Cooktop
Lock key and
universal off
Classic Trim
ICT15E/S
762 mm Framed Electric Cooktop
True Simmer on
all elements
Classic Trim
914 mm Framed Electric Cooktop
Classic Trim
Framed edge
ICT30E/S
ICT36E/S
Location of
rating plate
Hot surface
indicators
9
WOLF ELECTRIC COOKTOPS
ACCESSORIES
Optional accessories
are available
through your Wolf
dealer.
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
From a planning perspective, your selection
process is made easier by the three different
sizes you have to choose from. For ease of
installation, Wolf recommends using 838 mm
cabinets with the 762 mm cooktop and 991 mm
cabinets with the 914 mm cooktop.
Electric cooktops require a separate, grounded
220-240 V AC, 50/60 Hz electrical supply with
its own circuit breaker. Locate electrical supply
within the shaded area shown in the Installation
Specifications illustration for your model.
Specifications on the following pages provide
overall dimensions, countertop cut-out dimensions and installation specifics for the three
different-sized cooktops. We have minimized
the information contained in the illustrations,
concentrating on the critical information you
need to plan your installation.
A Wolf single built-in oven may be installed
below these cooktops. Wolf framed electric
cooktops are designed and agency approved for
installation with Wolf built-in ovens only. Also,
be aware of the depth of the cooktop when
planning for this installation.
IMPORTANT NOTE: When an oven is installed
below the cooktop, it is recommended that the
electrical supply be placed in the base cabinet to
the right of the oven, unless you are using
cabinets deeper than 610 mm. Refer to pages
6–7 for additional specifications for built-in
ovens.
You must follow all local codes and ordinances
when installing your service.
These cooktops are intended for indoor use.
Multiple cooktops and/or integrated modules
can be installed side by side. Refer to the countertop cut-out dimensions on page 19 when
planning for this installation.
These cooktops can accommodate a Wolf
cooktop hood or downdraft system. When
installing a ventilation hood, refer to the specific
requirements of the hood for the minimum
dimension to the countertop. Refer to pages
57–66 for ventilation specifications.
ACCESSORIES
Electric Cooktops
Filler strip
Bracket supports for installation
of two integrated modules with
downdraft (Model DD30 only)
Accessories are available through
your Wolf dealer.
10
This appliance must be installed in accordance with
local codes. The correct voltage, frequency and
amperage must be supplied to the appliance from a
dedicated, grounded circuit that is protected by a
properly sized circuit breaker or time delay fuse.
The proper voltage, frequency and amperage ratings
are listed on the product rating plate.
WOLF ELECTRIC COOKTOPS
OVERALL DIMENSIONS
Model ICT15E/S
MODEL OPTIONS
381 mm Framed Electric Cooktop
Classic Trim Finish
533 mm
ICT15E/S
OVERALL
DEPTH
S P E C I F I C AT I O N S
381 mm Framed Electric Cooktop
381 mm
OVERALL WIDTH
89 mm
Overall Width
381 mm
Overall Height
89 mm
Overall Depth
533 mm
Heating Elements
Two
Temperature Zones
Three
Max Element Power 750 W / 2200 W
(dual)
Unit dimensions may vary to ± 3 mm.
Max Element Power 1200 W
(single)
Cabinet Depth
578 mm min
I N S TA L L AT I O N S P E C I F I C AT I O N S
Height Clearance
102 mm min
Model ICT15E/S
Cut-Out Width*
340 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Conduit
1.2 m flexible 3-wire
Electrical Rating
3.4 kW at 240 V
Shipping Weight
14 kg
838 mm RECOMMENDED
330 mm
max
CABINET WIDTH
457 mm
51**
489 mm
mm COOKTOP CUT-OUT
DEPTH
64 mm
min
51 mm min*
762 mm
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
340 mm
CUT-OUT TO
COMBUSTIBLE COOKTOP CUT-OUT
WIDTH
MATERIALS
(BOTH SIDES)
102 mm
E
914 mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
381
mm
381 mm
*If the 381 mm cooktop is to be used with
any combination of additional cooktop units or
modules with a filler strip, the cut-out width
increases to 356 mm.
The outer diameter of the heating elements are
229 mm and 165 mm.
I N S TA L L AT I O N
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm
recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out
to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up
to 457 mm above countertop.
340 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT
WIDTH
489 mm
64 mm
min
COOKTOP
CUT-OUT DEPTH
FRONT OF COUNTERTOP
11
WOLF ELECTRIC COOKTOPS
OVERALL DIMENSIONS
762 mm Framed Electric Cooktop
MODEL OPTIONS
762 mm Framed Electric Cooktop
Classic Trim Finish
ICT30E/S
533 mm
OVERALL
DEPTH
S P E C I F I C AT I O N S
762 mm Framed Electric Cooktop
Overall Width
762 mm
Overall Height
89 mm
Overall Depth
533 mm
Heating Elements
Four
Temperature Zones
Six
762 mm
OVERALL WIDTH
89 mm
Max Element Power 750 W / 2200 W and
(two dual)
950 W / 1900 W
Max Element Power 1200 W and 1500 W
(two single)
Unit dimensions may vary to ± 3 mm.
Cabinet Width
838 mm rec
762 mm min
I N S TA L L AT I O N S P E C I F I C AT I O N S
Cabinet Depth
578 mm min
762 mm Framed Electric Cooktop
Height Clearance
102 mm min
Cut-Out Width*
721 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
40 amp dedicated circuit
Conduit
1.2 m flexible 3-wire
Electrical Rating
6.8 kW at 240 V
Shipping Weight
20 kg
*If the 762 mm cooktop is to be used with
any combination of additional cooktop units or
modules with a filler strip, the cut-out width
increases to 737 mm.
838 mm RECOMMENDED
330 mm
max
51**
457
mm
489 mm
mm COOKTOP CUT-OUT
DEPTH
64 mm
min
51 mm min*
CUT-OUT TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
The outer diameter of the heating elements are
229 mm, 216 mm, 179 mm and 165 mm.
A Wolf 762 mm single oven may be installed
below the Wolf 762 mm framed electric
cooktop. For this installation, unless you are
using cabinets deeper than 610 mm, it is
recommended that the electrical supply be
placed in the base cabinet to the right of the
oven. A Wolf 914 mm single oven may also
be installed below the Wolf 762 mm framed
electric cooktop. Refer to pages 6 and 7 for
additional specifications.
762 mm
762 mm min
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
721 mm COOKTOP
CUT-OUT WIDTH
102 mm
E
89 mm
610 mm min
I N S TA L L AT I O N O P T I O N S
CABINET WIDTH
95 mm
min
914 mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
254
mm
762 mm OVEN OPENING
*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.
**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.
721 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT WIDTH
Refer to installation instructions shipped with
each Wolf product for detailed specifications.
489 mm
COOKTOP
CUT-OUT DEPTH
64 mm
min
FRONT OF COUNTERTOP
12
WOLF ELECTRIC COOKTOPS
OVERALL DIMENSIONS
914 mm Framed Electric Cooktop
MODEL OPTIONS
914 mm Framed Electric Cooktop
Classic Trim Finish
533 mm
ICT36E/S
OVERALL
DEPTH
S P E C I F I C AT I O N S
914 mm Framed Electric Cooktop
914 mm
OVERALL WIDTH
89 mm
Overall Width
914 mm
Overall Height
89 mm
Overall Depth
533 mm
Heating Elements
Five
Temperature Zones
Eight
Max Element Power 1050 W / 2200 W /
(triple)
2700 W
Unit dimensions may vary to ± 3 mm.
Max Element Power 750 W / 2200 W
(dual)
Max Element Power 1200 W, 1500 W
(three single)
and 1800 W
I N S TA L L AT I O N S P E C I F I C AT I O N S
914 mm Framed Electric Cooktop
991 mm
330 mm
max
51**
457
mm
489 mm
mm COOKTOP CUT-OUT
DEPTH
64 mm
min
51 mm min*
CUT-OUT TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
RECOMMENDED CABINET WIDTH
762 mm
914 mm min
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
873 mm
COOKTOP CUT-OUT WIDTH
102 mm
89 mm
610 mm min
95 mm
min
914 mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
Cabinet Width
991 mm rec
914 mm min
Cabinet Depth
578 mm min
Height Clearance
102 mm min
Cut-Out Width*
873 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
50 amp dedicated circuit
Conduit
1.2 m flexible 3-wire
Electrical Rating
9.4 kW at 240 V
Shipping Weight
27 kg
*If the 914 mm cooktop is to be used with
any combination of additional cooktop units or
modules with a filler strip, the cut-out width
increases to 889 mm.
E
The outer diameter of the heating elements
are 302 mm, 232 mm, 200 mm, 181 mm and
165 mm.
254
mm
914 mm OVEN OPENING
I N S TA L L AT I O N O P T I O N S
A Wolf 914 mm single oven may be installed
below the Wolf 914 mm framed electric
cooktop. For this installation, unless you are
using cabinets deeper than 610 mm, it is
recommended that the electrical supply be
placed in the base cabinet to the right of the
oven. A Wolf 762 mm single oven may also
be installed below the Wolf 914 mm framed
electric cooktop. Refer to pages 6 and 7 for
additional specifications.
*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.
**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.
873 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT WIDTH
489 mm
COOKTOP
CUT-OUT DEPTH
64 mm
min
When a 914 mm oven is installed below a
cooktop, it is recommended that the rough
opening for the oven be 197 mm from the
floor to ease the use of the oven door.
FRONT OF COUNTERTOP
13
WOLF GAS COOKTOPS
Model ICBCT15G/S
381 mm
Gas Cooktop
Model ICBCT30G/S
762 mm
Gas Cooktop
WOLF GAS COOKTOPS
FEATURES
New features make cooking a greater pleasure
than ever. For instance, at higher settings the
dual-stacked burner design uses its upper-level
burner for maximum heat transfer. Merely turn
down the illuminated knob and the lower-tier
burners deliver fine-tuning control and True
Simmer. You’ll see why we patented this
concept when you can have the slightest of
flame and enjoy a simmer with no boiling or
scorching. This is heat tailored for every cooking
vessel you’re using—from the largest stockpot to
the smallest melting pan.
Available in natural and LP gas
A more powerful 5.0 kW burner is standard on
the 762 mm and 914 mm gas cooktops.
The dual-stacked sealed burners and deep
recess of the seamless drawn pan area make
cleanup of any of those previously unsightly
spills a snap.
Stainless steel top construction, available in
classic stainless steel finish
Dual-stacked, sealed burners with automatic
reignition on all settings
Large 5.0 kW burner with .2 kW delivered at
simmer—Models ICBCT30G/S and ICBCT36G/S
only
Medium 4.0 kW burner with .2 kW delivered at
simmer
Small 3.2 kW burners with .1 kW delivered at
simmer
Electronic spark ignition system
True Simmer setting on all burners
Illuminated control panel with two-tiered control
knobs
Low-profile, cast iron continuous burner grates
with matte porcelain finish
Seamless drawn burner pan
Model ICBCT36G/S
914 mm
Gas Cooktop
CE certified
This appliance is certified by
Star-K to meet strict religious
regulations in conjunction with
specific instructions found on
www.star-k.org.
G A S C O O K T O P F E AT U R E S
Model ICBCT36G/S shown
Small 3.2 kW
burners
Low-profile
continuous grates
Two-tiered
control knobs
MODEL OPTIONS
Gas Cooktops
381 mm Gas Cooktop
Illuminated
control panel
Classic Stainless
762 mm Gas Cooktop
Classic Stainless
Medium 4.0 kW
burner
Large 5.0 kW
burner
14
ICBCT30G/S
914 mm Gas Cooktop
Classic Stainless
Location of rating
plate
Seamless
drawn pan
ICBCT15G/S
ICBCT36G/S
WOLF GAS COOKTOPS
PLANNING INFORMATION
ELECTRICAL | GAS REQUIREMENTS
Wolf recommends using 838 mm cabinets with
the 762 mm cooktop and 991 mm cabinets with
the 914 mm cooktop.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
Specifications on the following pages provide
overall dimensions, countertop cut-out dimensions and installation specifics for the three
different-sized cooktops. We have minimized
the information contained in the illustrations,
concentrating on the critical information you
need to plan your installation.
Wolf gas cooktops are designed to operate on
natural gas, I2H, I2E, and I2E+ at 20 mb pressure
or LP (propane) gas at 37 mb WC pressure. They
are supplied with an ISO 14 male gas connection
at the right rear corner on the bottom of the
cooktop. The male connector exits the unit
straight down.
A Wolf single built-in oven may be installed
below these cooktops. Wolf gas cooktops are
designed and agency approved for installation
with Wolf built-in ovens only. Also, be aware of
the depth of the cooktop when planning for this
installation.
Locate electrical and gas supply within the
shaded area shown in the Installation Specifications illustration for your model.
Multiple cooktops and/or integrated modules
can be installed side by side. Refer to the countertop cut-out dimensions on page 19 when
planning for this installation.
These cooktops can accommodate a Wolf
cooktop hood or downdraft system. When
installing a ventilation hood, refer to the specific
requirements of the hood for the minimum
dimension to the countertop. Refer to pages
57–66 for ventilation specifications.
IMPORTANT NOTE: When an oven is installed
below the cooktop, it is recommended that the
electrical supply be placed in the base cabinet to
the right of the oven, unless you are using
cabinets deeper than 610 mm. Refer to pages
6–7 for additional specifications for built-in
ovens.
When a gas cooktop is installed above cabinets,
the gas and electrical placement is not critical.
A grounded outlet needs to be placed within
1.2 m of the right rear of the cooktop.
You must follow all local codes and ordinances
when installing your services.
These cooktops are intended for indoor use.
ACCESSORIES
Gas Cooktops
One-piece wok and single burner
grate (Models ICBCT30G/S and
ICBCT36G/S)
Filler strip
Bracket supports for installation
of two integrated modules with
downdraft (Model DD30 only)
Accessories are available through
your Wolf dealer.
15
WOLF GAS COOKTOPS
OVERALL DIMENSIONS
381 mm Gas Cooktop
MODEL OPTIONS
381 mm Gas Cooktop
Classic / Natural Gas ICBCT15G/S
533 mm
Classic / LP Gas
OVERALL
DEPTH
ICBCT15G/S-LP
S P E C I F I C AT I O N S
381 mm Gas Cooktop
381 mm
OVERALL WIDTH
Overall Width
381 mm
Overall Height
102 mm
Overall Depth
533 mm
Burner Rating
(1) 4.0 kW with .2 kW
delivered at simmer
(1) 3.2 kW with .1 kW
delivered at simmer
102 mm
Unit dimensions may vary to ± 3 mm.
Cabinet Depth
578 mm min
Height Clearance
102 mm min
Cut-Out Width
356 mm
I N S TA L L AT I O N S P E C I F I C AT I O N S
Cut-Out Depth
489 mm
381 mm Gas Cooktop
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Gas Rating
7.2 kW
Shipping Weight
14 kg
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N O P T I O N S
838 mm RECOMMENDED
330 mm
max
For the 381 mm gas cooktop, the gas service
may be supplied through the floor if the
cooktop is not installed above an oven. Refer
to the illustration for specifics on placement
of gas and electrical.
64**
mm
CABINET WIDTH
457
mm
489 mm
COOKTOP CUT-OUT
DEPTH
64 mm
min
178 mm min*
762 mm
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
356 mm
CUT-OUT TO
COMBUSTIBLE COOKTOP CUT-OUT
WIDTH
MATERIALS
(BOTH SIDES)
102 mm
Refer to installation instructions shipped with
each Wolf product for detailed specifications.
E
914 mm
LOCATION OF GAS
SUPPLY MAY ALSO
EXTEND 127 mm
ON FLOOR
FROM BACK WALL
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
G
381
mm
381 mm
LOCATION OF GAS SUPPLY
MAY ALSO EXTEND 127 mm ON
FLOOR FROM BACK WALL
127
mm
381 mm
NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 33" (838) recommended cabinet width. 457 mm
recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out
to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up
to 457 mm above countertop.
356 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT
WIDTH
489 mm
64 mm
min
COOKTOP
CUT-OUT DEPTH
FRONT OF COUNTERTOP
16
WOLF GAS COOKTOPS
OVERALL DIMENSIONS
762 mm Gas Cooktop
MODEL OPTIONS
762 mm Gas Cooktop
533 mm
Classic / Natural Gas ICBCT30G/S
OVERALL
DEPTH
Classic / LP Gas
ICBCT30G/S-LP
S P E C I F I C AT I O N S
762 mm Gas Cooktop
762 mm
OVERALL WIDTH
102 mm
Overall Width
762 mm
Overall Height
102 mm
Overall Depth
533 mm
Burner Rating
(1) 5.0 kW with .2 kW
delivered at simmer
(1) 4.0 kW with .2 kW
delivered at simmer
Unit dimensions may vary to ± 3 mm.
(2) 3.2 kW with .1 kW
delivered at simmer
I N S TA L L AT I O N S P E C I F I C AT I O N S
762 mm Gas Cooktop
838 mm RECOMMENDED
330 mm
max
64**
mm
457
mm
489 mm
COOKTOP CUT-OUT
DEPTH
610 mm min
64 mm
min
229 mm min*
CUT-OUT TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
CABINET WIDTH
762 mm
762 mm min
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
737 mm COOKTOP
CUT-OUT WIDTH
102 mm
89 mm
95 mm
min
914 mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
E
Cabinet Width
838 mm rec
762 mm min
Cabinet Depth
578 mm min
Height Clearance
102 mm min
Cut-Out Width
737 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Gas Rating
15.4 kW
Shipping Weight
23 kg
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N O P T I O N S
A Wolf 762 mm single oven may be installed
below the Wolf 762 mm gas cooktop. For this
installation, unless you are using cabinets
deeper than 610 mm, it is recommended that
the electrical and gas supply be placed in the
base cabinet to the right of the oven. Refer
to page 6 for additional specifications.
G
254
mm
762 mm OVEN OPENING
*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.
**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.
737 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT WIDTH
489 mm
COOKTOP
CUT-OUT DEPTH
64 mm
min
FRONT OF COUNTERTOP
17
WOLF GAS COOKTOPS
OVERALL DIMENSIONS
914 mm Gas Cooktop
MODEL OPTIONS
914 mm Gas Cooktop
Classic / Natural Gas ICBCT36G/S
533 mm
Classic / LP Gas
OVERALL
DEPTH
ICBCT36G/S-LP
S P E C I F I C AT I O N S
914 mm Gas Cooktop
914 mm
Overall Width
914 mm
Overall Height
102 mm
Overall Depth
533 mm
Burner Rating
(1) 5.0 kW with .2 kW
delivered at simmer
(1) 4.0 kW with .2 kW
delivered at simmer
OVERALL WIDTH
102 mm
Unit dimensions may vary to ± 3 mm.
(3) 3.2 kW with .1 kW
delivered at simmer
Cabinet Width
991 mm rec
914 mm min
Cabinet Depth
578 mm min
Height Clearance
102 mm min
Cut-Out Width
889 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Gas Rating
18.6 kW
Shipping Weight
30 kg
I N S TA L L AT I O N O P T I O N S
I N S TA L L AT I O N S P E C I F I C AT I O N S
914 mm Gas Cooktop
64**
mm
A Wolf 914 mm single oven may be installed
below the Wolf 914 mm gas cooktop. For this
installation, unless you are using cabinets
deeper than 610 mm, it is recommended that
the electrical and gas supply be placed in the
base cabinet to the right of the oven. A Wolf
762 mm single oven may also be installed
below the Wolf 914 mm gas cooktop. Refer
to pages 6 and 7 for additional specifications.
991 mm
330 mm
max
457
mm
489 mm
COOKTOP CUT-OUT
DEPTH
64 mm
min
229 mm min*
CUT-OUT TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
RECOMMENDED CABINET WIDTH
762 mm
914 mm min
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
889 mm
COOKTOP CUT-OUT WIDTH
102 mm
89 mm
610 mm min
95 mm
min
914 mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
E
G
254
mm
914 mm OVEN OPENING
When a 914 mm oven is installed below a
cooktop, it is recommended that the rough
opening for the oven be 197 mm from the
floor to ease the use of the oven door.
Refer to installation instructions shipped with
each Wolf product for detailed specifications.
*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.
**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.
889 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT WIDTH
489 mm
COOKTOP
CUT-OUT DEPTH
64 mm
min
FRONT OF COUNTERTOP
18
WOLF INTEGRATED MODULES
WOLF INTEGRATED MODULES
With Wolf‘s integrated modules, you have the
ultimate in customization. You can create your
own design by mixing and matching the various
components within this system. And when you
couple these modules with other cooktops
within the Wolf inventory, you and your client
will truly understand freedom of choice.
IMPORTANT NOTE: Refer to specifications on
the following pages for specific installation
requirements and limitations for each integrated
module. Review specific installation instructions
for product-to-product capabilities. Additional
information is provided in the specifications pdf
files on our website, wolfappliance.com
Some modules integrate with their larger
counterparts, right down to their low-profile
grates, dual-stacked gas burners, deep spill pan
and illuminated controls. The two-element
electric and dual-stacked sealed burner gas
cooktop modules deliver the same performance
and appearance as the larger electric and gas
cooktops.
Refer to the following illustration for countertop
cut-out dimensions for the installation of
multiple cooktops or modules.
Some integrated modules can be installed
together or with a 762 mm or 914 mm cooktop.
When multiple cooktops or modules are installed
side by side, the cut-out dimensions shown in
the illustration below are derived by adding
32 mm additional space for each additional unit,
to give you your total cut-out width.
IMPORTANT NOTE: When multiple cooktops or
modules are installed side by side, each unit
must have its own separate recommended
electrical circuit. When multiple gas cooktops or
modules are installed next to one another, they
can receive their gas supply from a common line.
However, each unit must have its own regulator
installed between the mainline and the cooktop
or module.
Model CT15I/S
Induction Cooktop
Model ICT15E/S
Electric Cooktop
Model ICBIG15/S
Electric Grill
These integrated modules are intended for
indoor use.
Model ICBIS15/S
Electric Steamer
C O U N T E R T O P C U T- O U T D I M E N S I O N S
Installation of Multiple Cooktops or Modules
1518 mm – FOUR MODULES WIDTH OR
1511 mm – 762 mm COOKTOP AND TWO MODULES OR
1276 mm – 914 mm COOKTOP AND ONE MODULE
1130 mm – THREE MODULES WIDTH OR
1124 mm – 762 mm COOKTOP AND ONE MODULE
743 mm
Model ICBIF15/S
Electric Fryer
I N T E G R AT E D M O D U L E S
381 mm Width
TWO MODULES WIDTH
356 mm
64 mm
min
CUT-OUT
WIDTH
489 mm
CUT-OUT
DEPTH
Induction Cooktop
CT15I/S
Electric Cooktop
ICT15E/S
Electric Grill
ICBIG15/S
Electric Steamer
ICBIS15/S
Electric Fryer
ICBIF15/S
Gas Cooktop
ICBCT15G/S
Gas Multi-Function
Cooktop
IIM15/S
Model ICBCT15G/S
Gas Cooktop
FRONT OF COUNTERTOP
All integrated modules are available in
the classic stainless steel finish.
IMPORTANT NOTE: When two or more modules are
installed together, an integrated module filler strip is
recommended. If a Model DD30 downdraft system is
also installed, an integrated module support for downdraft ventilation is required. Contact your Wolf dealer
for information on these accessory components.
IMPORTANT NOTE: Refer to specifications on the following pages for specific
installation requirements and limitations
for each integrated module. Specifications for Model ICT15E/S are found on
page 11 and Model ICBCT15G/S specifications are on page 16.
Model IIM15/S
Gas Multi-Function
Cooktop
19
WOLF INTEGRATED MODULES
Model CT15I/S
Induction Cooktop
INDUCTION COOKTOP
FEATURES
While induction cooking is new to North
America, it has been used in Europe for decades
by professionals and homeowners demanding
the best in performance.
Integrated design allows for installation of
multiple cooktops or modules
Cooking with this sleek 15-inch powerhouse is
simply the best way to cook. Electricity flows
through a coil to produce a magnetic field under
the sleek black ceramic top. When an iron or
magnetic stainless steel pan is placed on the
surface, the magnetic field creates a current in
the pan, exciting the molecules and heating the
pan and not the cooktop. That‘s why the
cooktop stays cool to the touch and the food
cooks efficiently.
In fact, this unit is so efficient that it outperforms gas and electric cooktops. There is no
wasted heat because energy is supplied directly
to the cooking vessel, so nearly 90 percent of
the energy gets used to cook.
You can keep sauces and chocolates melted at
50 watts of power, or with the touch of a finger,
activate the hi-power boost feature and boil
water in nearly half the time you normally do.
Classic stainless steel trim finish
Easy-to-clean black ceramic glass surface is
resistant to scratching, staining, impact and heat
Induction elements heat cookware not the glass,
for a cooler and safer cooking surface
Cookware sensing—elements will not be
energized without an iron or magnetic stainless
steel pan on the cooktop surface
Illuminated electronic touch controls with
graduated control lighting
High-efficiency elements deliver power and
control
Hi-Power mode boosts power on rear element
to 2200 W maximum power output by diverting
power from front element
Simultaneous operation of both elements at
1800 W each
True Simmer setting on both elements
Melt setting on both elements
Temperature limiter to ensure that safe operating temperature of ceramic glass is never
exceeded
The Wolf induction cooktop has it all.
Child safety lock key and universal off
I N D U C T I O N C O O K T O P F E AT U R E S
OVERALL DIMENSIONS
Model CT15I/S
Model CT15I/S
Two induction
elements
Illuminated electronic
touch controls
533 mm
OVERALL
DEPTH
Lock key and
universal off
H
HIG
LT
ME
ON
OFF
WER
HI-PO
HIGH
ON
OFF
SIM
O
OFF
381 mm
OVERALL WIDTH
64 mm
Classic stainless
steel trim finish
True Simmer and melt
on both elements
Location of
rating plate
ACCESSORIES
Induction Cooktop
Filler strip
Bracket supports for installation
of two integrated modules with
762 mm downdraft
Accessories are available through
your Wolf dealer.
20
WOLF INTEGRATED MODULES
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
The illustrations provide the overall dimensions
and finished cut-out dimensions that you need
to plan for in your installation. We have minimized the information contained in the illustrations, concentrating on the critical information
you must plan into your installation.
The Wolf induction cooktop requires a separate,
grounded 3-wire 220-240 V AC, 50/60 Hz, 20
amp service with its own circuit breaker. Locate
electrical within the shaded area shown in the
illustration.
You must follow all local codes and ordinances
when installing your service.
IMPORTANT NOTE: When multiple cooktops or
modules are installed side by side, refer to page
19 for countertop cut-out dimensions.
I N S TA L L AT I O N
The induction cooktop can accommodate a
Wolf cooktop hood or downdraft system. When
installing a ventilation hood, refer to the specific
requirements of the hood for the minimum
dimension to the countertop. Refer to pages
57–66 for ventilation specifications.
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
I N S TA L L AT I O N S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Model CT15I/S
Model CT15I/S
Induction Cooktop
838 mm RECOMMENDED
330 mm
max
51**
CABINET WIDTH
457
mm
489 mm
mm COOKTOP CUT-OUT
DEPTH
64 mm
min
51 mm min*
762 mm
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
340 mm
CUT-OUT TO
COMBUSTIBLE COOKTOP CUT-OUT
WIDTH
MATERIALS
(BOTH SIDES)
114 mm
E
914 mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
381
mm
381 mm
NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm
recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out
to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up
to 457 mm above countertop.
Trim Finish
Classic
Overall Width
381 mm
Overall Height
64 mm
Overall Depth
533 mm
Induction Elements
Two
Max Element Power 1800 W
(front)
Max Element Power 2200 W
(rear)
Cabinet Depth
578 mm min
Height Clearance
152 mm min
Cut-Out Width*
340 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
20 amp dedicated circuit
Conduit
1.2 m flexible 3-wire
Electrical Rating
3.4 kW
Shipping Weight
14 kg
*If the induction cooktop is to be used with
any combination of additional cooktop units or
modules with a filler strip, the cut-out width
increases to 356 mm.
340 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT
WIDTH
489 mm
64 mm
min
COOKTOP
CUT-OUT DEPTH
IMPORTANT NOTE: A minimum height clearance
of 152 mm is required. If a shelf is installed
below the unit, a 25 mm gap at the rear of the
cabinet shelf is necessary to allow for proper
ventilation. Failure to do so could result in
decreased performance or product damage.
Unit dimensions may vary to ± 3 mm.
FRONT OF COUNTERTOP
21
WOLF INTEGRATED MODULES
Model ICBIG15/S
Electric Grill Module
ELECTRIC GRILL MODULE
FEATURES
Who says you have to sacrifice the fun of grilling
when the weather changes and you cannot take
advantage of the outdoors? With this grill
cooktop you can easily handle steaks and all
sorts of food without the hassle of lava rocks
or briquettes.
Integrated design allows for installation of
multiple cooktops or modules
There are two individual heating elements—front
and back—on this module that enable you to
cook on one side while keeping other items at
serving temperature.
For ease of cleaning, there are porcelainized
plates below two 1400-watt heating elements
that accumulate any unwanted grease and drain
it away.
The Wolf electric grill module is available in
classic stainless steel.
Stainless steel top construction with classic
stainless steel finish
Two 1400-watt, individually controlled heating
elements—front and back—for even grilling
Illuminated electronic touch controls with
graduated control lighting
Low-profile, one-piece cast iron grilling grate
with matte porcelain finish
Black porcelain-coated grease deflection plates
Easy-to-clean, removable porcelain collection
pan
Independent digital timer
CE certified
This appliance is certified by Star-K
to meet strict religious regulations in
conjunction with specific instructions
found on www.star-k.org.
E L E C T R I C G R I L L F E AT U R E S
OVERALL DIMENSIONS
Model ICBIG15/S
Model ICBIG15/S
Low-profile, one-piece
grilling grate
Two 1400-watt
heating elements
533 mm
OVERALL
DEPTH
Illuminated electronic
touch controls
381 mm
OVERALL WIDTH
159 mm
Removable
collection pan
Graduated
control lighting
Location of
rating plate
ACCESSORIES
Electric Grill Module
Filler strip
Accessories are available through
your Wolf dealer.
22
WOLF INTEGRATED MODULES
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
The illustrations provide the overall dimensions
and finished cut-out dimensions that you need
to plan for in your installation. We have minimized the information contained in the illustrations, concentrating on the critical information
you need to plan your installation.
The Wolf International electric grill module is CB
approved and and is manufactured for a 220-240
V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown in the illustration.
You must follow all local codes and ordinances
when installing your service.
IMPORTANT NOTE: When multiple cooktops or
modules are installed side by side, refer to page
19 for countertop cut-out dimensions.
I N S TA L L AT I O N
The grill module can accommodate a Wolf
cooktop hood. When installing a ventilation
hood, refer to the specific requirements of the
hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications.
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
IMPORTANT NOTE: Wolf does not recommend
the use of downdraft ventilation with the grill
module.
I N S TA L L AT I O N S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Model ICBIG15/S
Model ICBIG15/S
Electric Grill Module
838 mm RECOMMENDED
330 mm
max
51**
CABINET WIDTH
457
mm
489 mm
mm COOKTOP CUT-OUT
DEPTH
64 mm
min
178 mm min*
762 mm
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
356 mm
CUT-OUT TO
COMBUSTIBLE COOKTOP CUT-OUT
WIDTH
MATERIALS
(BOTH SIDES)
159 mm
914 mm
E
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
381
mm
Exterior Finish
Classic
Overall Width
381 mm
Overall Height
159 mm
Overall Depth
533 mm
Temperature Zones
Two
Heating Element
Zone (front)
1400 W
Heating Element
Zone (rear)
1400 W
Total Element Power 2800 W
Cabinet Depth
578 mm min
Height Clearance
159 mm min
Cut-Out Width
356 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Electrical Rating
2.8 kW
Shipping Weight
28 kg
381 mm
Unit dimensions may vary to ± 3 mm.
NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm
recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out
to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up
to 457 mm above countertop.
356 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT
WIDTH
489 mm
64 mm
min
COOKTOP
CUT-OUT DEPTH
FRONT OF COUNTERTOP
23
WOLF INTEGRATED MODULES
Model ICBIS15/S
Electric Steamer
Module
ELECTRIC STEAMER MODULE
FEATURES
From a temperature of 60˚C to boil, you can keep
food hot for long periods of time or defrost
easily without drying out or losing flavor.
Integrated design allows for installation of
multiple cooktops or modules
The beauty of this steamer module is accented
by the sculptured glass domed lid, which is
easily inverted for storage to keep a low profile.
The deep, large vessel with a 7.6 L capacity can
hold up to 3.3 L of cooked pasta. Includes one
solid and one perforated stackable insert pan.
The diversity of our electric steamer includes
slow cooking, double boiling, steaming eggs,
steaming custard, proofing bread dough,
warming food and melting chocolate as well
as steaming vegetables.
The Wolf electric steamer module is available
in classic stainless steel.
Stainless steel top construction with classic
stainless steel finish
Hidden 2600-watt heating element
Illuminated electronic touch controls with
graduated control lighting
Large 7.6 L maximum capacity tub—2.4 L
capacity for steaming
Two stackable stainless steel steamer insert
pans—one solid and one perforated
Uses include steaming vegetables, eggs and
custard, double boiling, proofing bread dough,
warming food and melting chocolate
Can function as a slow cooker for 8–10 hours
Reversible domed glass lid for easy storage
Independent digital timer
This steamer module must be installed at
least 381 mm away from a Wolf fryer
module, as contact between water and hot
oil may cause burns from steam and hot oil.
Digital temperature readout and preheat indicator
Electronic drain
CE certified
This appliance is certified by Star-K
to meet strict religious regulations in
conjunction with specific instructions
found on www.star-k.org.
E L E C T R I C S T E A M E R F E AT U R E S
OVERALL DIMENSIONS
Model ICBIS15/S
Model ICBIS15/S
Reversible
domed glass lid
Hidden 2600-watt
heating element
533 mm
OVERALL
DEPTH
Illuminated electronic
touch controls
381 mm
OVERALL WIDTH
Graduated
control lighting
Deep drawn pan
191 mm
343 mm
TO DRAIN
OUTLET
Location of
rating plate
Digital temperature
readout
ACCESSORIES
Electric Steamer Module
Filler strip
Accessories are available through
your Wolf dealer.
24
WOLF INTEGRATED MODULES
PLANNING INFORMATION
The illustrations provide the overall dimensions
and finished cut-out dimensions that you need
to plan for in your installation.
The steamer module can accommodate a Wolf
cooktop hood. When installing a ventilation
hood, refer to the specific requirements of the
hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications.
IMPORTANT NOTE: When multiple cooktops or
modules are installed side by side, refer to page
19 for countertop cut-out dimensions.
IMPORTANT NOTE: Wolf does not recommend
the use of downdraft ventilation with the
steamer module.
For the drain connection, the 16 mm outlet from
the valve will accept a drain hose that must flow
downward to, and tie into, an existing sink drain.
A separate drain with a freefall may also be
installed. (Following local building codes, your
plumber will dictate how to plumb the unit.) As a
third option, the consumer will supply a heat
resistant bucket for drainage in the location of
the drain outlet. Refer to the illustration for
location of the drain outlet.
ELECTRICAL REQUIREMENTS
The Wolf International electric steamer module is
CB approved and and is manufactured for a
220-240 V AC, 50/60 Hz electrical supply. Locate
electrical within the shaded area shown.
I N S TA L L AT I O N
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
You must follow all local codes and ordinances
when installing your service.
I N S TA L L AT I O N S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Model ICBIS15/S
Model ICBIS15/S
Electric Steamer Module
838 mm RECOMMENDED
330 mm
max
51**
CABINET WIDTH
457
mm
489 mm
mm COOKTOP CUT-OUT
DEPTH
64 mm
min
178 mm min*
343
mm
314 mm
194
mm
DRAIN OUTLET
LOCATION
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
356 mm
CUT-OUT TO
COMBUSTIBLE COOKTOP CUT-OUT
WIDTH
MATERIALS
(BOTH SIDES)
314 mm
152
mm
914 mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
E
762 mm
DRAIN
OUTLET
LOCATION
Exterior Finish
Classic
Overall Width
381 mm
Overall Height
343 mm
Overall Depth
533 mm
Heating Element
2600 W
Cabinet Depth
578 mm min
Height Clearance
343 mm min
Cut-Out Width
356 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Electrical Rating
2.6 kW
Shipping Weight
18 kg
Unit dimensions may vary to ± 3 mm.
381
mm
381 mm
NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm
recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out
to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up
to 457 mm above countertop.
356 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT
WIDTH
This steamer module must be installed
at least 381 mm away from a Wolf
fryer module, as contact between
water and hot oil may cause burns
from steam and hot oil.
489 mm
64 mm
min
COOKTOP
CUT-OUT DEPTH
FRONT OF COUNTERTOP
25
WOLF INTEGRATED MODULES
Model ICBIF15/S
Electric Fryer Module
ELECTRIC FRYER MODULE
FEATURES
To round out your options for the ideal kitchen,
you can choose a fryer, and Wolf offers a great
option that the market has never seen. When
your clients use this module, they‘ll be able to
create dinner specialties never tried before.
Integrated design allows for installation of
multiple cooktops or modules
The accurate temperature control will enable
your customer to seal in that great flavor of the
food without absorbing any unnecessary grease.
The fryer can handle a variety of foods at a wide
range of oil temperatures.
The Wolf fryer module is available in classic
stainless steel. In addition, there is a metal
storage lid to keep the grease area free from
particles falling into the fryer.
Stainless steel top construction with classic
stainless steel finish
Hidden 2600-watt heating element
Illuminated electronic touch controls with
graduated control lighting
Large 3.8 L capacity tub
Three baskets included—one large and two small
side by side, each with wire basket hanger
Low-profile lid
Melt feature for shortening or lard
Independent digital timer
Digital temperature readout and preheat indicator
This fryer module must be installed at least
381 mm away from any open flame cooking
device. The open flame may cause ignition
of oil.
Easy manual locking drain capability
Recommended for installation with any Wolf
framed electric cooktop or the Wolf electric grill
module
CE certified
This fryer module must be installed at least
381 mm away from a Wolf steamer module,
as contact between water and hot oil may
cause burns from steam and hot oil.
E L E C T R I C F R Y E R F E AT U R E S
OVERALL DIMENSIONS
Model ICBIF15/S
Model ICBIF15/S
Low-profile lid
Hidden 2600-watt
heating element
533 mm
OVERALL
DEPTH
Illuminated electronic
touch controls
381 mm
OVERALL WIDTH
Graduated
control lighting
Deep drawn pan
191 mm
343 mm
TO DRAIN
OUTLET
Location of
rating plate
Digital temperature
readout
ACCESSORIES
Electric Fryer Module
Filler strip
Accessories are available through
your Wolf dealer.
26
WOLF INTEGRATED MODULES
PLANNING INFORMATION
The illustrations provide the overall dimensions
and finished cut-out dimensions that you need
to plan for in your installation.
IMPORTANT NOTE: Wolf does not recommend
the use of downdraft ventilation with the fryer
module.
IMPORTANT NOTE: When multiple cooktops or
modules are installed side by side, refer to page
19 for countertop cut-out dimensions.
ELECTRICAL REQUIREMENTS
The Wolf International electric fryer module is CB
approved and and is manufactured for a 220-240
V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown in the illustration.
The electric fryer module must be installed in a
base cabinet with access to the bottom of the
unit to drain the oil through a manual valve. The
consumer must supply a heat resistant bucket
to accept the drained oil. Refer to the illustration
for location of the drain outlet.
You must follow all local codes and ordinances
when installing your service.
The fryer module can accommodate a Wolf
cooktop hood. When installing a ventilation
hood, refer to the specific requirements of the
hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications.
I N S TA L L AT I O N S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Model ICBIF15/S
Model ICBIF15/S
Electric Fryer Module
838 mm RECOMMENDED
330 mm
max
51**
CABINET WIDTH
457
mm
489 mm
mm COOKTOP CUT-OUT
DEPTH
64 mm
min
178 mm min*
314 mm
194
mm
DRAIN OUTLET
LOCATION
914 mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
356 mm
CUT-OUT TO
COMBUSTIBLE COOKTOP CUT-OUT
WIDTH
MATERIALS
(BOTH SIDES)
314 mm
152
mm
DRAIN OUTLET
LOCATION
762 mm
343
mm
I N S TA L L AT I O N
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
Exterior Finish
Classic
Overall Width
381 mm
Overall Height
343 mm
Overall Depth
533 mm
Heating Element
2600 W
Cabinet Depth
578 mm min
Height Clearance
343 mm min
Cut-Out Width
356 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Electrical Rating
2.6 kW
Shipping Weight
14 kg
Unit dimensions may vary to ± 3 mm.
E
381
mm
381 mm
NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm
recommended cabinet width for installation of single 381 mm cooktop or module. NOTE: Fryer module must be installed in a base cabinet with
access to manual valve at base of unit to drain oil into heat resistant receptacle. *Minimum clearance from both side edges of cooktop cut-out
to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up
to 457 mm above countertop.
This fryer module must be installed at
least 381 mm away from any open
flame cooking device. The open flame
may cause ignition of oil.
356 mm
Countertop Cut-Out Dimensions
COOKTOP CUT-OUT
WIDTH
489 mm
64 mm
min
COOKTOP
CUT-OUT DEPTH
This fryer module must be installed at
least 381 mm away from a Wolf
steamer module, as contact between
water and hot oil may cause burns
from steam and hot oil.
FRONT OF COUNTERTOP
27
WOLF INTEGRATED MODULES
Model IIM15/S
Gas Multi-Function
Cooktop
G A S M U LT I - F U N C T I O N C O O K T O P
FEATURES
It’s really a misnomer to describe this wonderful
cooktop module as a wok instrument because it
is much more than that. The large, low-profile
grate will fit in nicely with any Wolf gas cooktop.
Integrated design allows for installation of
multiple cooktops or modules
For true wok cooking, the burner sculpts the gas
flame into a plume, focusing heat in the center
of the wok, then dispersing it outward for
precisely controlled cooking. The larger grate will
handle your wok perfectly but will also accommodate your largest stockpots and Dutch ovens.
The powerful burner exceeds 5.3 kW.
The Wolf multi-function cooktop is available
in classic stainless steel.
Available in natural and LP gas
Stainless steel top construction with classic
stainless steel finish
High output 5.3 kW burner
Automatic electronic reignition system
Illuminated control panel
Individual spark ignition system
Two interchangeable cast iron burner grates
with matte porcelain finish—wok grate and lowprofile continuous grate
Deep drawn burner pan
G A S M U LT I - F U N C T I O N C O O K T O P F E AT U R E S
OVERALL DIMENSIONS
Model IIM15/S
Gas Multi-Function Cooktop
High-output
5.3 kW burner
Wok grate
shown
533 mm
OVERALL
DEPTH
381 mm
OVERALL WIDTH
Illuminated
control panel
Deep drawn pan
127 mm
Continuous
control knob
ACCESSORIES
Location of
rating plate
Gas Multi-Function Cooktop
Filler strip
Bracket supports for installation
of two integrated modules with
762 mm downdraft
Accessories are available through
your Wolf dealer.
28
WOLF INTEGRATED MODULES
PLANNING INFORMATION
ELECTRICAL | GAS REQUIREMENTS
The illustrations provide the overall dimensions
and finished cut-out dimensions that you need
to plan for in your installation.
The Wolf International gas multifunction cooktop
is CB approved and and is manufactured for a
220-240 V AC, 50/60 Hz electrical supply. Locate
electrical within the shaded area shown. You
must follow all local codes and ordinances when
installing your service.
IMPORTANT NOTE: When multiple cooktops or
modules are installed side by side, refer to page
19 for countertop cut-out dimensions.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
This cooktop can accommodate a Wolf cooktop
hood or downdraft system. When installing a
ventilation hood, refer to the specific requirements of the hood for the minimum dimension to
the countertop. Refer to pages 57–66 for ventilation specifications.
The gas multi-function cooktop is designed to
operate on natural gas at 12.5 mb or LP (propane)
gas at 25 mb. The minimum line pressure for
natural gas is 17.5 mb and 27.4 mb for LP gas.
The maximum gas supply pressure to the regulator should never exceed 34.9 mb. It is supplied
with an ISO 14 male gas connection at the right
rear corner of the module. The male connector
exits the unit straight down, and you are supplied
with a regulator with two female connectors.
I N S TA L L AT I O N S P E C I F I C AT I O N S
MODEL OPTIONS
Gas Multi-Function Cooktop
Gas Multi-Function Cooktop
Classic / Natural Gas IIM15/S
Classic / LP Gas
IIM15/S-LP
S P E C I F I C AT I O N S
Gas Multi-Function Cooktop
838 mm RECOMMENDED
330 mm
max
64**
mm
CABINET WIDTH
457
mm
489 mm
COOKTOP CUT-OUT
DEPTH
64 mm
min
178 mm min*
762 mm
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
356 mm
CUT-OUT TO
COMBUSTIBLE COOKTOP CUT-OUT
WIDTH
MATERIALS
(BOTH SIDES)
127 mm
E
914 mm
LOCATION OF GAS
SUPPLY MAY ALSO
EXTEND 127 mm
ON FLOOR
FROM BACK WALL
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
G
381
mm
381 mm
Overall Height
127 mm
Overall Depth
533 mm
Burner Rating
5.3 kW
Cabinet Depth
578 mm min
Height Clearance*
127 mm min
Cut-Out Width
356 mm
Cut-Out Depth
489 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Gas Rating
5.3 kW
Shipping Weight
14 kg
381 mm
LOCATION OF GAS SUPPLY
MAY ALSO EXTEND 127 mm ON
FLOOR FROM BACK WALL
127
mm
381 mm
NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm
recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out
to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up
to 457 mm above countertop.
356 mm
Countertop Cut-Out Dimensions
Overall Width
*A minimum height clearance of 140 mm is
required between countertop and any combustible
surface directly below the cooktop.
Unit dimensions may vary to ± 3 mm.
COOKTOP CUT-OUT
WIDTH
I N S TA L L AT I O N
489 mm
64 mm
min
COOKTOP
CUT-OUT DEPTH
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
FRONT OF COUNTERTOP
29
WOLF WARMING DRAWERS
Model ICBWWD30
with Stainless Steel
Drawer Front
Model ICBWWD30
with Integrated
Drawer Front
WOLF WARMING DRAWER
FEATURES
Warming drawers have a clear mission in life—
to take good care of good food until it’s time for
you to eat. Our superior air control helps keep
moist foods moist and crisp foods crisp. In
addition, Wolf warming drawers are among the
most spacious on the market, so you will have
little problem storing items.
Stainless steel drawer front and tubular handle
There is a rack for stacking food plus an optional
set of six stainless steel containers with lids that
divide the drawer into sections, keeping different
dishes warm at the same time.
Preset automatic shut-off or extended operation
in Sabbath Mode
Electronic controls are hidden regardless of your
panel selection. Choose from the classic stainless steel look or the integrated drawer front,
which allows for a custom wood panel. Wolf
offers optional decorative handles for the integrated drawer front. Keep in mind, there are
significant changes to the installation procedure
if you plan on using the integrated drawer front.
Integrated drawer front allows for custom wood
panel application
850-watt heating element
Hidden electronic touch control panel
Preset and variable temperature control
Stainless steel interior
Rack for stacking food
Removable stainless steel drawer pan
Full-extension, ball bearing drawer glides
CE certified
This appliance is certified by Star-K
to meet strict religious regulations in
conjunction with specific instructions
found on www.star-k.org.
W A R M I N G D R A W E R F E AT U R E S
Model ICBWWD30
(stainless steel drawer front shown)
Removable stainless
steel drawer pan
Galvanized exterior
Rack for stacking
food
Stainless steel
interior
Hidden electronic
touch control panel
ACCESSORIES
Warming Drawer
Ball bearing
drawer glides
Location of
rating plate
Stainless steel
drawer front shown
(sold as an accessory)
Six-piece container set—includes
six stainless steel pans with
lids; one 6.3 L pan, one
3.9 L pan, two 2.8 L pans, two
1.7 L pans and pan rack
Accessories are available through
your Wolf dealer.
30
WOLF WARMING DRAWERS
PLANNING INFORMATION
INTEGRATED DRAWER FRONT
The Wolf 762 mm warming drawer is shipped
without any decorative drawer front. You must
order a stainless steel drawer front (tubular
handle included) or the integrated front (no
handle) for a custom wood application.
IMPORTANT NOTE: A minimum 838 mm wide
cabinet is required for the warming drawer with
integrated drawer front. A minimum 610 mm
deep cabinet is required for an overlay application and 635 mm deep cabinet for a flush inset
application.
Specifications on the following pages provide
overall dimensions, rough openings and installation options for Model ICBWWD30 with stainless
steel and integrated drawer fronts. Note that
there are significant differences to the installation requirements for the integrated drawer front.
An anti-tip block or platform must be installed to
prevent the unit from tipping forward when the
drawer is opened.
The base platform must be able to support
91 kg. This platform must be a minimum of
25 mm above the toe kick to allow for the
16 mm overlap of the warming drawer trim.
Model ICBWWD30 may be installed below a
Wolf built-in oven or an electric or gas cooktop,
provided the warming drawer is fully enclosed,
top and bottom. It may also be installed next to
or above another Model ICBWWD30. Dimensions
will vary according to the specific installation.
STAINLESS STEEL DRAWER FRONT
Wolf recommends using a 838 mm wide cabinet
for the warming drawer with stainless steel
drawer front. A minimum 762 mm wide by
610 mm deep cabinet is required.
Model ICBWWD30 with integrated drawer front
can accommodate installations with a 762 mm
or 914 mm cooktop. It may also be installed in
combination with a 762 mm single or double
oven or a 914 mm single oven. Dimensions will
vary according to the specific installation.
Keep in mind that the width of the custom panel
for the warming drawer with integrated drawer
front will vary according to the specific installation. The opening width will remain 749 mm
whether installed in combination with a 762 mm
or 914 mm cooktop or oven.
ACCESSORIES
Optional accessories
are available
through your Wolf
dealer.
The decorative wood drawer front panel must
be a minimum of 16 mm thick.
ELECTRICAL REQUIREMENTS
Model ICBWWD30 is CB approved and manufactured for a 220-240 V AC, 50/60 Hz electrical
supply. The service should have its own 15 or
20 amp circuit breaker, and a grounded 3-prong
receptacle should be located within reach of the
power cord and flush with the back wall. Locate
electrical within the shaded area shown in the
installation illustrations on the following pages.
OVERALL DIMENSIONS
Model ICBWWD30 with Stainless Steel Drawer Front
689 mm
OVERALL DEPTH
260 mm
229 mm
FRONT PANEL OPTIONS
Model ICBWWD30
759 mm
597 mm
OVERALL WIDTH
BEHIND FRAME
Classic Stainless
Model ICBWWD30 with Integrated Drawer Front
257 mm
229 mm
746 mm
597 mm
OVERALL WIDTH
BEHIND FRAME
WWDFRONT/S
Integrated
WWDFRONT/I
(accepts wood panel)
Optional drawer front panels are
ordered and shipped as sales
accessories. Stainless steel drawer
front panels include matching tubular
handle.
31
WOLF WARMING DRAWERS
I N S TA L L AT I O N S P E C I F I C AT I O N S
Model ICBWWD30 with Stainless Steel Drawer Front
Undercounter Installation
S P E C I F I C AT I O N S
Model ICBWWD30 with
Stainless Steel Drawer Front
838 mm
RECOMMENDED CABINET WIDTH
51 mm x 51 mm
Overall Width
759 mm
Overall Height
260 mm
Overall Depth
(behind frame)
597 mm
ANTI-TIP BLOCK
762 mm min
DIMENSION
WILL VARY*
127
mm
232 mm
OPENING
HEIGHT
Interior Capacity
45 L
Cabinet Width
838 mm rec
762 mm min
914 mm
606 mm min
OPENING DEPTH
Cabinet Depth
610 mm min
Min Base Support
91 kg
Opening Width
727 mm
Opening Height
232 mm
Opening Depth
606 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 or 20 amp circuit
Heating Element
850 W
Shipping Weight
45 kg
610 mm min
STANDARD
FLOOR TO
COUNTER
HEIGHT
ALLOW FOR
16 mm
OVERLAP OF
DRAWER FACE
ON ALL SIDES
E
102 mm
727 mm
127 mm min
OPENING WIDTH
BOTTOM
OF OPENING
TO FLOOR
CABINET DEPTH
*Allow enough room for placement of anti-tip block and drawer face overlap.
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N
OPTIONS
Model ICBWWD30 with
stainless steel drawer front
may be installed above or
below a Wolf 762 mm single
or double oven, or below an
electric or gas cooktop,
provided the warming
drawer is fully enclosed,
top and bottom, with a
minimum base support of
91 kg. Refer to the built-in
oven and cooktop sections
for additional specifications.
It may also be installed next
to or above another Model
ICBWWD30.
Model ICBWWD30 with
stainless steel drawer front
may be installed in combination with a 762 mm single
oven.
Refer to the installation
instructions provided with
the stainless steel drawer
front for detailed specifications. These instructions
can also be found on our
website, wolfappliance.com.
Dimensions will vary
according to the specific
installation.
32
Installation below 762 mm Built-In Single Oven
610 mm min
610 mm min
CABINET DEPTH
CABINET DEPTH
838 mm
RECOMMENDED CABINET WIDTH
762 mm min
724 mm
610 mm min
691 mm
610 mm min
691 mm
762 mm OVEN
ROUGH OPENING
22 mm
51 mm x 51 mm
PLATFORM
ANTI-TIP BLOCK
232 mm
OPENING
HEIGHT
OPENING
HEIGHT
606 mm min
606 mm min
OPENING DEPTH
OPENING DEPTH
PLATFORM APPLICATION
127 E
mm
232 mm
22
mm
ANTI-TIP BLOCK APPLICATION
60
mm
ALLOW FOR
16 mm
OVERLAP OF
DRAWER FACE
ON ALL SIDES
102 mm
727 mm
WARMING DRAWER
OPENING WIDTH
NOTE: Refer to the built-in 762 mm single oven specifications for electrical location.
WOLF WARMING DRAWERS
I N S TA L L AT I O N S P E C I F I C AT I O N S
Model ICBWWD30 with Integrated Drawer Front
Undercounter Installation
S P E C I F I C AT I O N S
Model ICBWWD30 with
Integrated Drawer Front
Overlay Application
838 mm
51 mm x 51 mm
ANTI-TIP BLOCK
DIMENSION
WILL VARY*
RECOMMENDED CABINET WIDTH
762 mm min
127 E
mm
260 mm
251 mm
OPENING
HEIGHT
914 mm
STANDARD
FLOOR TO
COUNTER
HEIGHT
610 mm min
OPENING DEPTH
610 mm min
102 mm
ALLOW FOR
OVERLAP OF
DECORATIVE
DRAWER FACE
ON ALL SIDES**
749 mm
OPENING WIDTH
127 mm min
BOTTOM
OF OPENING
TO FLOOR
CABINET DEPTH
*Allow enough room for placement of anti-tip block and drawer face overlap.
**Overlap of decorative drawer face will vary depending on the size of the custom panel.
Flush Inset Application
ANTI-TIP BLOCK
DIMENSION
WILL VARY*
746 mm
Overall Height
257 mm
Overall Depth
(behind frame)
597 mm
Interior Capacity
45 L
Min Cabinet Width
838 mm
Min Cabinet Depth
Overlay
Flush Inset
610 mm
635 mm
Min Base Support
91 kg
Opening Width
749 mm
Opening Height
260 mm
Opening Depth*
610 mm
Min Panel Size (W x H)
Overlay
762 mm x 264 mm
Flush Inset
746 mm x 257 mm
838 mm
51 mm x 51 mm
Overall Width
MINIMUM CABINET WIDTH
Min Panel Thickness 16 mm
127 E
mm
260 mm
251 mm
OPENING
HEIGHT
102 mm
914 mm
610 mm + THICKNESS
OF DRAWER FACE
FOR OPENING DEPTH
Electrical Supply
220-240 V AC, 50/60 Hz
15 or 20 amp circuit
Heating Element
850 W
Shipping Weight
45 kg
749 mm
STANDARD
FLOOR TO
COUNTER
HEIGHT
OPENING WIDTH
127 mm min
BOTTOM
OF OPENING
TO FLOOR
635 mm min
*For flush inset application, add thickness of
drawer face to opening depth.
CABINET DEPTH
Unit dimensions may vary to ± 3 mm.
*Allow enough room for placement of anti-tip block.
I N S TA L L AT I O N
OPTIONS
Installation below 762 mm Built-In Single Oven
610 mm min
635 mm min
838 mm
CABINET DEPTH
CABINET DEPTH
CABINET WIDTH
610 mm min
691 mm
610 mm min
691 mm
724 mm
762 mm OVEN
OPENING WIDTH
51 mm x 51 mm
51 mm x 51 mm
ANTI-TIP BLOCK
ANTI-TIP BLOCK
251 mm
OPENING
HEIGHT
610 mm min
OPENING DEPTH
OVERLAY APPLICATION
127 E
mm
260 mm
260 mm
251 mm
38 mm
min*
OPENING
HEIGHT
610 mm + THICKNESS
OF DRAWER FACE
FOR OPENING DEPTH
FLUSH INSET APPLICATION
102 mm
38 mm
min*
749 mm
WARMING DRAWER
OPENING WIDTH
NOTE: Refer to the built-in 762 mm single oven specifications for electrical location.
Model ICBWWD30 with
integrated drawer front
may be installed above or
below any Wolf built-in
oven, or below an electric
or gas cooktop, provided
the warming drawer is fully
enclosed, top and bottom,
with a minimum base
support of 91 kg. Refer to
the cooktop and oven
sections for additional specifications. It may also be
installed next to or above
another Model ICBWWD30.
Model ICBWWD30 with
integrated drawer front
may be installed in combination with a 762 mm or 914
mm single oven.
Refer to the installation
instructions provided for
detailed specifications.
These instructions can also
be found on our website,
wolfappliance.com.
*Dimension may increase depending on the size of the drawer front panel.
33
WOLF DUAL FUEL RANGES
WOLF DUAL FUEL RANGES
With Wolf‘s dual fuel ranges you have state-ofthe-art cooking expertise in any number of sizes
to meet the discriminating consumer’s precise
needs. Patented features ensure this range
stands out from the rest in performance and
also beauty.
T O P C O N F I G U R AT I O N S
Dual Fuel Ranges
IDF364C
IDF486C
IDF606CG
IDF364G
IDF486G
IDF604CF
IDF484CG
IDF484F
This appliance is certified by
Star-K to meet strict religious
regulations in conjunction with
specific instructions found on
www.star-k.org.
Wolf dual fuel ranges come in 914 mm,
1219 mm and 1524 mm widths. Combined with
the top configuration options, the different
configurations you can choose from are
numerous. Model numbers indicate the top
configurations: (C) charbroiler, (G) griddle and
(F) French Top. All Wolf dual fuel ranges come
in the classic stainless steel finish.
The electric oven(s) feature the Wolf exclusive
dual convection system that delivers even
temperature and airflow throughout. Its combination of convection fans and heating elements
give the user convenience and superior control
over ten different cooking modes.
Advanced standard features such as dualstacked sealed burners, dual convection fans,
cobalt blue porcelain oven interior, pivoting
control panel, along with the Wolf exclusive
infrared charbroiler, infrared griddle and French
Top are all yours for the asking. The freedom to
customize your dual fuel range will make you
and your client look great.
COOKING MODES
Bake
Roast
Broil
Convection Bake
Convection Roast
Convection Broil
Convection
Bake Stone*
Dehydrate*
Proof
* Accessory required.
34
WOLF DUAL FUEL RANGES
FEATURES
Natural or LP gas rangetop with dual convection
electric oven(s)
Pivoting hidden touch control panel
457 mm oven on 1219 mm range is single
convection
Self-cleaning oven(s) with cobalt blue porcelain
oven interior
Optional infrared charbroiler, infrared griddle
and French Top configurations
Coaxial temperature-displaying oven selector
knob
Classic stainless steel exterior finish with island
trim included
Proof mode for 457 mm oven on 1219 mm
range
Distinctive red or black control knobs
Temperature probe
Platinum bezels surround all knobs—chrome or
brass bezels optional
Three removable oven racks, six-level rack guide
and full-extension bottom rack
Dual-stacked, sealed surface burners, all with
simmer capabilities and automatic reignition at
all settings
Hidden bake element and recessed broil element
4.4 kW burners with .3 kW delivered at simmer
2.7 kW burner with .1 kW delivered at simmer
and melt feature
Ten cooking modes
Triple-pane oven door window(s) and dual
halogen lighting
Spring/Damper door system on oven door(s)
Adjustable stainless steel legs in front and
adjustable rear casters
Porcelain-coated cast iron continuous top grates
D U A L F U E L R A N G E F E AT U R E S
Model IDF484CG shown
Infrared griddle
(optional)
Infrared charbroiler
(optional)
Continuous cast
iron top grates
ACCESSORIES
Dual Fuel Ranges
127 mm and 254 mm classic
stainless steel risers
Stainless steel
island trim
Pivoting hidden
control panel
Dual-stacked,
sealed burners
Control knobs with
platinum bezels
Griddle
indicator light
Location of rating
plate
Chrome or brass bezels
Coaxial oven
selector knob
Coaxial oven
selector knob
Porcelain-cast two-burner
S-grate
Stainless steel
exterior finish
Dual halogen
oven lighting
Single convection
oven— 1219 mm
range only
Spring/Damper
door system
508 mm classic stainless steel
riser with shelf
Red or black control knobs—
must be ordered with the range
One-piece wok grate and single
burner grate
Two-piece broiler pan and
temperature probe
Additional oven racks
Hardwood cutting board—
griddle models only
Bake stone accessory
Dehydration accessory
Spring/Damper
door system
Front leg extension covers and
rear leg caster covers
Adjustable front legs
and rear casters
Blue porcelain oven
interiors
Dual convection
oven
Accessories are available through
your Wolf dealer.
35
WOLF DUAL FUEL RANGES
PLANNING INFORMATION
ELECTRICAL | GAS REQUIREMENTS
Wolf dual fuel ranges come in 914 mm,
1219 mm and 1524 mm widths. Specifications
on the following pages provide overall dimensions, finished rough opening dimensions and
installation specifics for each size of dual fuel
range. We have minimized the information
contained in the illustrations, concentrating on
the critical information you need to plan your
installation.
Specifications on the following pages provide
electrical and gas requirements for each size
of dual fuel range.
IMPORTANT NOTE: Caution must be used in
planning the proper installation of the Wolf dual
fuel range to avoid fires or damage to adjacent
cabinetry or kitchen equipment. Please follow
the minimum clearances established in the
finished rough opening dimensions. Refer to
specifications on the following pages for your
model.
Locate electrical and gas supply within the
shaded area shown in the Installation Specifications illustration for your model.
International (I) models come with a factory
installed transformer and require a 220-240 V
AC, 50/60 Hz electrical supply, fused at the
correct rating for the unit. The appropriate electrical connection must be provided in accordance
with local requirements.
Wolf dual fuel ranges are designed to operate on
natural gas at 12.5 mb WC (water column)
pressure or LP (propane) gas at 25 mb WC
pressure. The minimum line pressure for natural
gas is 17.5 mb WC and 27.4 mb WC for LP gas.
The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa.
Wolf recommends the use of a 13 mm I.D.
commercial-type flex hose; this is the minimum
size that may be used. All plumbing to the flex
hose must be 19 mm minimum I.D. pipe.
IMPORTANT NOTE: A separate external gas
shut-off valve must be located near the range
in an accessible location.
You must follow all local codes and ordinances
when installing your services.
B U R N E R R AT I N G
Dual Fuel Ranges
Surface Burners
4.4 kW with .3 kW
delivered at simmer
(1) 2.7 kW with .1 kW
delivered at simmer
Infrared Charbroiler
4.7 kW
Infrared Griddle
Natural Gas
LP Gas
4.4 kW
3.8 kW
French Top
4.4 kW
Refer to the specific model requirements
for risers in non-island installations.
36
WOLF DUAL FUEL RANGES
OVERALL DIMENSIONS
914 mm Dual Fuel Range
S P E C I F I C AT I O N S
749 mm
OVERALL DEPTH
914 mm Dual Fuel Range
699 mm
Overall Width
235
mm
1445
mm
WITH
508 mm
RISER
616 mm
1191
mm
937 mm
OVERALL
HEIGHT TO
COOKING
SURFACE
WITH
254 mm
RISER
911 mm
1064
mm
WITH
127 mm
RISER
911 mm
1194 mm
OVERALL WIDTH
LEGS AND CASTERS ALLOW
54 mm HEIGHT ADJUSTMENT
911 mm
Overall Height
(to cooking surface) 937 mm
Overall Depth
749 mm
Overall Oven
Interior Capacity
153 L
Overall Interior Dim
(W x H x D)
762 mm x 419 mm
x 483 mm
Usable Interior Dim
(W x H x D)
673 mm x 419 mm
x 416 mm
Opening Width
914 mm
Electrical Supply
220-240 V AC, 50/60 Hz
30 amp dedicated
circuit
Electrical Rating
5.2 kW at 240 V
Total Amps
21.7
Shipping Weight
202–213 kg
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S
MODEL OPTIONS
914 mm Dual Fuel Range
914 mm Dual Fuel Range
Four Surface Burners
914 mm min
152 mm min
762 mm min TO
914 mm max
1118 mm min
FOR CHARBROILER
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
TO BOTTOM OF
VENTILATION HOOD
330 mm
max
457 mm min
IMPORTANT NOTE: A
minimum 254 mm riser is
required when installing a
914 mm dual fuel range
with a charbroiler or griddle
against a combustible
surface.
TO COUNTERTOP
914 mm
914 mm
937 mm
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
TO
COOKING
SURFACE
381 mm
LOCATION
OF GAS
SUPPLY
IDF364G
I N S TA L L AT I O N
FINISHED ROUGH OPENING WIDTH
216
mm
IDF364C
Griddle
Natural gas models listed;
for LP gas add (-LP) to the
model number.
VENTILATION HOOD
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
Charbroiler
83 mm
483 mm
LOCATION OF GAS AND
ELECTRICAL EXTENDS 76 mm
ON FLOOR FROM BACK WALL
LOCATION OF
ELECTRICAL
ISLAND INSTALLATIONS: 305 mm MINIMUM
CLEARANCE FROM BACK OF RANGE TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0 mm TO NON-COMBUSTIBLE MATERIALS
37
WOLF DUAL FUEL RANGES
OVERALL DIMENSIONS
1219 mm Dual Fuel Range
S P E C I F I C AT I O N S
749 mm
OVERALL DEPTH
1219 mm Dual Fuel Range
Overall Width
699 mm
1216 mm
235
mm
Overall Height
(to cooking surface) 937 mm
1445
mm
Overall Depth
749 mm
Large Oven —
Overall Interior Cap
127 L
Overall Interior Dim
(W x H x D)
635 mm x 419 mm
x 483 mm
Usable Interior Dim
(W x H x D)
546 mm x 419 mm
x 416 mm
Small Oven —
Overall Interior Cap
71 L
Overall Interior Dim
(W x H x D)
356 mm x 419 mm
x 483 mm
Usable Interior Dim
(W x H x D)
295 mm x 419 mm
x 416 mm
Opening Width
1219 mm
Electrical Supply
220-240 V AC, 50/60 Hz
50 amp dedicated
circuit
Electrical Rating
10.2 kW at 240 V
Total Amps
42.5
Shipping Weight
302–340 kg
WITH
508 mm
RISER
616 mm
1191
mm
937 mm
OVERALL
HEIGHT TO
COOKING
SURFACE
WITH
254 mm
RISER
911 mm
1064
mm
WITH
127 mm
RISER
1194 mm
1216 mm
OVERALL WIDTH
LEGS AND CASTERS ALLOW
54 mm HEIGHT ADJUSTMENT
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S
1219 mm Dual Fuel Range
MODEL OPTIONS
1219 mm Dual Fuel Range
Six Surface Burners
Charbroiler
IDF486C
Griddle
IDF486G
VENTILATION HOOD
Four Surface Burners
Charbroiler and
Griddle
IDF484CG
French Top
IDF484F
914 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
152 mm min
Natural gas models listed;
for LP gas add (-LP) to the
model number.
IMPORTANT NOTE: A
minimum 254 mm riser is
required for all 1219 mm dual
fuel range models installed
against a combustible surface.
762 mm min TO
914 mm max
1118 mm min
FOR CHARBROILER
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
TO BOTTOM OF
VENTILATION HOOD
330 mm
max
457 mm min
TO COUNTERTOP
1219 mm
FINISHED ROUGH OPENING WIDTH
914 mm
937 mm
TO
COOKING
SURFACE
254 mm
610 mm
LOCATION
OF GAS
SUPPLY
83 mm
330 mm
LOCATION OF GAS AND
ELECTRICAL EXTENDS 76 mm
ON FLOOR FROM BACK WALL
38
LOCATION OF
ELECTRICAL
ISLAND INSTALLATIONS: 305 mm MINIMUM
CLEARANCE FROM BACK OF RANGE TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0 mm TO NON-COMBUSTIBLE MATERIALS
WOLF DUAL FUEL RANGES
OVERALL DIMENSIONS
1524 mm Dual Fuel Range
S P E C I F I C AT I O N S
749 mm
OVERALL DEPTH
1524 mm Dual Fuel Range
699 mm
Overall Width
235
mm
1445
mm
WITH
508 mm
RISER
616 mm
1191
mm
937 mm
OVERALL
HEIGHT TO
COOKING
SURFACE
WITH
254 mm
RISER
911 mm
1064
mm
WITH
127 mm
RISER
1527 mm
1194 mm
OVERALL WIDTH
LEGS AND CASTERS ALLOW
54 mm HEIGHT ADJUSTMENT
1527 mm
Overall Height
(to cooking surface) 937 mm
Overall Depth
749 mm
Overall Oven Interior
Capacity (per oven) 127 L
Overall Interior Dim
(W x H x D)
635 mm x 419 mm
x 483 mm each
Usable Interior Dim
(W x H x D)
546 mm x 419 mm
x 416 mm each
Opening Width
1530 mm
Electrical Supply
220-240 V AC, 50/60 Hz
50 amp dedicated
circuit
Electrical Rating
10.2 kW at 240 V
Total Amps
42.5
Shipping Weight
397–431 kg
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S
MODEL OPTIONS
1524 mm Dual Fuel Range
1524 mm Dual Fuel Range
Six Surface Burners
914 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
762 mm min TO
914 mm max
1118 mm min
FOR CHARBROILER
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
IDF606F
Charbroiler and
Griddle
IDF606CG
Natural gas models listed;
for LP gas add (-LP) to the
model number.
VENTILATION HOOD
152 mm min
French Top
TO BOTTOM OF
VENTILATION HOOD
330 mm
max
IMPORTANT NOTE: A
minimum 254 mm riser is
required for all 1524 mm dual
fuel range models installed
against a combustible surface.
457 mm min
TO COUNTERTOP
I N S TA L L AT I O N
1530 mm
FINISHED ROUGH OPENING WIDTH
914 mm
937 mm
TO
COOKING
SURFACE
254 mm
787 mm
LOCATION
OF GAS
SUPPLY
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
83 mm
330 mm
LOCATION OF GAS AND
ELECTRICAL EXTENDS 76 mm
ON FLOOR FROM BACK WALL
LOCATION OF
ELECTRICAL
ISLAND INSTALLATIONS: 305 mm MINIMUM
CLEARANCE FROM BACK OF RANGE TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0 mm TO NON-COMBUSTIBLE MATERIALS
39
WOLF SEALED BURNER RANGETOPS
WOLF SEALED BURNER RANGETOPS
T O P C O N F I G U R AT I O N S
Sealed Burner Rangetops
ICBSRT304
ICBSRT364C
ICBSRT364G
ICBSRT486C
ICBSRT486G
ICBSRT484CG
ICBSRT484F
This appliance is certified by
Star-K to meet strict religious
regulations in conjunction with
specific instructions found on
www.star-k.org.
40
There’s a good reason why professional chefs
choose gas cooking: control. The patented,
dual-stacked sealed gas burners of our new
sealed burner rangetop take control to a new
level. Two levels, really. The upper-tier burner
delivers maximum heat transfer at higher
settings; the lower-tier continuous flame ably
handles the subtleties of simmering and
melting.
Patented features along with the Wolf exclusive
infrared charbroiler, infrared griddle and French
Top ensure this rangetop stands out from the
rest in performance as well as beauty.
Wolf sealed burner rangetops come in 762 mm,
914 mm and 1219 mm widths and are available
in natural or LP gas, with your choice of several
top configurations. Model numbers indicate the
top configurations; (C) charbroiler, (G) griddle
and (F) French Top. The model number followed
by (-LP) denotes an LP gas model. All Wolf
sealed burner rangetops come in the classic
stainless steel finish.
WOLF SEALED BURNER RANGETOPS
FEATURES
Natural or LP gas models
5.0 kW burners with .3 kW delivered at simmer
Classic stainless steel exterior finish with
island trim
3.2 kW burner with .1 kW delivered at simmer
and melt feature
Optional infrared charbroiler, infrared griddle and
French Top configurations
Porcelain-coated cast iron continuous top grates
Distinctive red control knobs—optional black
knobs available at no cost
Platinum bezels surround all knobs—chrome or
brass bezels optional
Dual-stacked, sealed surface burners, all with
simmer capabilities and electronic reignition at all
settings
S E A L E D B U R N E R R A N G E T O P F E AT U R E S
Model ICBSRT484CG shown
Infrared griddle
(optional)
Infrared charbroiler
(optional)
Low-profile
island trim
Continuous,
cast iron top grates
Dual-stacked,
sealed burners
ACCESSORIES
Sealed Burner Rangetops
127 mm and 254 mm classic
stainless steel risers
508 mm classic stainless steel
riser with shelf
Stainless steel
exterior finish
Black control knobs—one set
available at no cost
Griddle indicator
light
Control knobs with
platinum bezels
Location of rating
plate
Chrome or brass bezels
One-piece wok grate and single
burner grate
Porcelain-cast two-burner
S-grate
SRT/Downdraft trim kit—Model
ICBSRT304 only
Hardwood cutting board—griddle
models only
Accessories are available through
your Wolf dealer.
41
WOLF SEALED BURNER RANGETOPS
PLANNING INFORMATION
ELECTRICAL | GAS REQUIREMENTS
Wolf sealed burner rangetops come in 762 mm,
914 mm and 1219 mm widths. Specifications on
the following pages provide overall dimensions,
finished rough opening dimensions and installation specifics for each size of sealed burner
rangetop. We have minimized the information
contained in the illustrations, concentrating on
the critical information you need to plan your
installation.
Specifications on the following pages provide
electrical and gas requirements for each size
of sealed burner rangetop.
IMPORTANT NOTE: Caution must be used in
planning the proper installation of the Wolf
sealed burner rangetop to avoid fires or damage
to adjacent cabinetry or kitchen equipment.
Please follow the minimum clearances established in the finished rough opening dimensions.
Refer to specifications on the following pages
for your model.
A downdraft can be used with Model
ICBSRT304. An accessory trim kit is necessary
for this installation. Contact your Wolf dealer for
details.
The Wolf sealed burner rangetop is CB approved
and manufactured for a 220-240 V AC, 50/60 Hz
electrical supply to operate the electronic ignition
system. The service should have its own 15 amp
circuit breaker.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
Wolf sealed burner rangetops are designed to
operate without a regulator on natural gas at
17-25 mb pressure or LP (propane) gas at 25-45
mb.
If local codes permit, a certified, .9 m long,
13 mm or 19 mm I.D. flexible metal appliance
connector is recommended for connecting the
rangetop to the gas supply line.
The platform for the rangetop must be 19 mm
thick and include a cut-out at the right rear for
gas supply and electrical connections.
Locate electrical and gas supply within the
shaded area shown in the Installation Specifications illustration for your model.
You must follow all local codes and ordinances
when installing your services.
B U R N E R R AT I N G
Sealed Burner Rangetops
Surface Burners
5.0 kW with .3 kW
delivered at simmer
(1) 3.2 kW with .1 kW
delivered at simmer
Infrared Charbroiler
Natural Gas
LP Gas
6.2 kW
5.4 kW
Infrared Griddle
Natural Gas
LP Gas
5.5 kW
5.5 kW
French Top
5.0 kW
Refer to the specific model requirements
for risers in non-island installations.
42
WOLF SEALED BURNER RANGETOPS
OVERALL DIMENSIONS
762 mm Sealed Burner Rangetop
S P E C I F I C AT I O N S
762 mm Sealed Burner Rangetop
724 mm
OVERALL DEPTH
Overall Width
699 mm
235
mm
COOKING
SURFACE
WITH 508 mm
RISER
318
mm
216 mm
OVERALL
HEIGHT
WITH
WITH 254 mm
RISER
127 mm
RISER
191
mm
759 mm
445
mm
759 mm
Overall Height
(to cooking surface) 216 mm
Overall Depth
724 mm
Opening Width
762 mm
Opening Height
191 mm
(platform to countertop)
616 mm
Opening Depth
1219 mm
Electrical Supply
220-240 V AC
50/60 Hz, 15 amp
dedicated circuit
Shipping Weight
73 kg
OVERALL WIDTH
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S
MODEL OPTIONS
762 mm Sealed Burner Rangetop
762 mm Sealed Burner
Rangetops
Four Surface
Burners
ICBSRT304
Natural gas model listed;
for LP gas add (-LP) to the
model number.
VENTILATION
HOOD
I N S TA L L AT I O N
762 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
330 mm
max
762 mm min
TO 914 mm max
TO BOTTOM OF
VENTILATION HOOD
152 mm min
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
457 mm min
TO COUNTERTOP
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
COOKING
SURFACE
216
mm
762 mm
OPENING WIDTH
19 mm
19 mm
406 mm
PLATFORM
PLATFORM
LOCATION OF GAS AND
ELECTRICAL SUPPLY CUT-OUT
WITHIN SHADED AREA
THROUGH BOTTOM OF
PLATFORM
TOP VIEW
OF PLATFORM
102 mm
E
191 mm
914 mm
610 mm
BACK
WALL
G
406 mm
ISLAND INSTALLATIONS: 305 mm MINIMUM
CLEARANCE FROM BACK OF RANGETOP TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0 mm TO NON-COMBUSTIBLE MATERIALS
43
WOLF SEALED BURNER RANGETOPS
OVERALL DIMENSIONS
914 mm Sealed Burner Rangetop
S P E C I F I C AT I O N S
914 mm Sealed Burner Rangetop
724 mm
OVERALL DEPTH
Overall Width
911 mm
Overall Height
(to cooking surface) 216 mm
Overall Depth
724 mm
Opening Width
914 mm
COOKING
SURFACE
Opening Height
191 mm
(platform to countertop)
Opening Depth
1219 mm
Electrical Supply
220-240 V AC
50/60 Hz, 15 amp
dedicated circuit
Shipping Weight
699 mm
235
mm
WITH 508 mm
RISER
318
mm
216 mm
191
mm
OVERALL
HEIGHT
911 mm
445
mm
WITH
WITH 254 mm
127 mm RISER
RISER
616 mm
OVERALL WIDTH
86–100 kg
Unit dimensions may vary to ± 3 mm.
MODEL OPTIONS
I N S TA L L AT I O N S P E C I F I C AT I O N S
914 mm Sealed Burner
Rangetops
914 mm Sealed Burner Rangetop
Four Surface Burners
Charbroiler
ICBSRT364C
Griddle
ICBSRT364G
Natural gas models listed;
for LP gas add (-LP) to the
model number.
VENTILATION HOOD
IMPORTANT NOTE: A minimum
254 mm riser is required for
charbroiler (C) or griddle (G)
models installed against a
combustible surface.
914 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
152 mm min
1118 mm min
FOR CHARBROILER
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
762 mm min TO
914 mm min
TO BOTTOM OF
VENTILATION HOOD
330 mm
max
457 mm min
TO COUNTERTOP
COOKING
SURFACE
216
mm
914 mm
FINISHED ROUGH OPENING WIDTH
19 mm
19 mm
406 mm
PLATFORM
PLATFORM
LOCATION OF GAS AND
ELECTRICAL SUPPLY CUT-OUT
WITHIN SHADED AREA
THROUGH BOTTOM OF
PLATFORM
TOP VIEW
OF PLATFORM
102 mm
E
191 mm
914 mm
610 mm
BACK
WALL
G
406 mm
ISLAND INSTALLATIONS: 305 mm MINIMUM
CLEARANCE FROM BACK OF RANGETOP TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0 mm TO NON-COMBUSTIBLE MATERIALS
44
WOLF SEALED BURNER RANGETOPS
OVERALL DIMENSIONS
1219 mm Sealed Burner Rangetop
S P E C I F I C AT I O N S
1219 mm Sealed Burner Rangetop
724 mm
OVERALL DEPTH
Overall Width
699 mm
235
mm
COOKING
SURFACE
WITH 508 mm
RISER
318
mm
216 mm
WITH
WITH 254 mm
127 mm RISER
RISER
191
mm
OVERALL
HEIGHT
1216 mm
445
mm
616 mm
1216 mm
Overall Height
(to cooking surface) 216 mm
Overall Depth
724 mm
Opening Width
1219 mm
Opening Height
191 mm
(platform to countertop)
Opening Depth
1219 mm
Electrical Supply
220-240 V AC
50/60 Hz, 15 amp
dedicated circuit
Shipping Weight
109–127 kg
OVERALL WIDTH
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S
MODEL OPTIONS
1219 mm Sealed Burner Rangetop
1219 mm Sealed Burner
Rangetops
Six Surface Burners
Charbroiler
ICBSRT486C
Griddle
ICBSRT486G
Four Surface Burners
VENTILATION HOOD
914 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
152 mm min
762 mm min TO
914 mm max
1118 mm min
FOR CHARBROILER
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
TO BOTTOM OF
VENTILATION HOOD
330 mm
max
457 mm min
COOKING
SURFACE
216
mm
1219 mm
19 mm
PLATFORM
LOCATION OF GAS AND
ELECTRICAL SUPPLY CUT-OUT
WITHIN SHADED AREA
THROUGH BOTTOM OF
PLATFORM
TOP VIEW
OF PLATFORM
102 mm
E
PLATFORM
914 mm
ICBSRT484F
Natural gas models listed;
for LP gas add (-LP) to the
model number.
191 mm
19 mm
406 mm
ICBSRT484CG
French Top
IMPORTANT NOTE: A minimum
254 mm riser is required for
charbroiler (C) or griddle (G)
models installed against a
combustible surface.
TO COUNTERTOP
FINISHED ROUGH OPENING WIDTH
Charbroiler
and Griddle
I N S TA L L AT I O N
610 mm
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
BACK
WALL
G
406 mm
ISLAND INSTALLATIONS: 305 mm MINIMUM
CLEARANCE FROM BACK OF RANGETOP TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0 mm TO NON-COMBUSTIBLE MATERIALS
45
WOLF GAS RANGES
WOLF GAS RANGES
If it looks as if it could be in a restaurant
kitchen, well, that’s natural. That’s precisely
where Wolf has spent the past seven decades,
perfecting the form, function and sheer durability of our stainless steel gas ranges.
T O P C O N F I G U R AT I O N S
Gas Ranges
IR304
IR364C
IR486C
IR364G
IR486G
IR484CG
This appliance is certified by
Star-K to meet strict religious
regulations in conjunction with
specific instructions found on
www.star-k.org.
46
IR606CG
Wolf gas ranges come in 762 mm, 914 mm,
1219 mm and 1524 mm widths, and
combined with the top configuration options,
the different configurations you can choose
from are numerous. Model numbers indicate
the top configurations: (C) charbroiler, (G)
griddle and (F) French Top.
Advanced standard features such as an
infrared oven broiler, convection baking and
dual burners along with the Wolf exclusive
infrared charbroiler, infrared griddle and French
Top are all yours for the asking. The freedom
to customize your gas range will make you
and your client look great.
All Wolf gas ranges come in the classic stainless steel finish and are shipped with the
distinctive red control knobs. Contact your
Wolf dealer for optional black knobs available
at no cost.
WOLF GAS RANGES
FEATURES
Natural or LP gas models
Large-capacity convection oven(s) with infrared
broiler, porcelain interior, three adjustable racks,
lights and door window
Fits standard 610 mm deep cabinets with zero
clearance for easy installation
Optional infrared charbroiler, infrared griddle and
French Top configurations
Classic stainless steel exterior finish
Dual brass burners with automatic reignition at
all settings, .1 kW simmer to 4.7 kW high
Porcelain-coated cast iron top grates
Large red control knobs with four position
settings and chrome bezels—optional black
knobs available
457 mm oven with porcelain interior, two
adjustable racks, lights and door window on
1219 mm range
Spring/Damper door system on oven door(s)
Stainless steel drip tray on ball bearing slides
Adjustable 76 mm stainless steel legs in front
and rear casters
Full side panels and skirt
G A S R A N G E F E AT U R E S
Model IR484CG shown with 127 mm riser
Porcelain-coated,
cast iron top grates
Infrared charbroiler
(optional)
Infrared griddle
(optional)
127 mm riser
(optional)
Large red
control knobs
Dual brass
burners
Location of
rating plate
Burner drip pan
Oven light
switch
Oven light switch
Stainless steel
exterior finish
Pull-out drip tray
Full side panels
and skirt
Convection fan
switch
Spring/Damper
door system
Oven indicator
light
ACCESSORIES
Gas Ranges
457 mm oven—
1219 mm range only
Large capacity
convection oven
Griddle indicator
light
127 mm and 254 mm classic
stainless steel risers
508 mm classic stainless steel
riser with shelf
Classic stainless steel island
trim
Black control knobs—available
at no cost
Porcelain-coated, cast iron wok
grate
Porcelain-coated, cast iron
two-burner S-grate
Hardwood cutting board—griddle
models only
Additional oven racks
Accessories are available through
your Wolf dealer.
47
WOLF GAS RANGES
PLANNING INFORMATION
ELECTRICAL | GAS REQUIREMENTS
Wolf gas ranges come in 762 mm, 914 mm,
1219 mm and 1524 mm widths. Specifications
on the following pages provide overall dimensions, finished rough opening dimensions and
installation specifics for each size of gas range.
We have minimized the information contained
in the illustrations, concentrating on the critical
information you need to plan your installation.
International (I) models come with a factory
installed transformer and require a 220-240
V AC, 50/60 Hz electrical supply, fused at the
correct rating for the unit. The appropriate electrical connection must be provided in accordance
with local requirements. The service should have
its own 15 amp circuit breaker.
IMPORTANT NOTE: Caution must be used in
planning the proper installation of the Wolf gas
range to avoid fires or damage to adjacent
cabinetry or kitchen equipment. Please follow
the minimum clearances established in the
finished rough opening dimensions. Refer to
specifications on the following pages for your
model.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
Locate electrical and gas supply within the
shaded area shown in the Installation Specifications illustration for your model.
Wolf gas ranges are designed to operate on
natural gas at 12.5 mb WC (water column)
pressure or LP (propane) gas at 25 mb WC
pressure. The minimum line pressure for natural
gas is 17.5 mb WC and 27.4 mb WC for LP gas.
The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa.
Wolf recommends the use of a 13 mm I.D.
commercial-type flex hose; this is the minimum
size that may be used. All plumbing to the flex
hose must be 19 mm minimum I.D. pipe.
IMPORTANT NOTE: A separate external gas
shut-off valve must be located near the range
in an accessible location.
You must follow all local codes and ordinances
when installing your services.
B U R N E R R AT I N G
Gas Ranges
Surface Burners
4.7 kW with .1 kW
delivered at simmer
Infrared Charbroiler
4.7 kW
Infrared Griddle
5.3 kW
French Top
4.4 kW
Oven Burner (Bake)
8.8 kW
Infrared Oven Broiler 5.3 kW
Refer to the specific model requirements
for risers in non-island installations.
48
WOLF GAS RANGES
OVERALL DIMENSIONS
762 mm Gas Range
721 mm
S P E C I F I C AT I O N S
OVERALL DEPTH
762 mm Gas Range
692 mm
Overall Width
235
mm
1441
mm
WITH
508 mm
RISER
622 mm
1187
mm
940 mm
WITH
254 mm
RISER
914 mm
OVERALL
HEIGHT TO
COOKING
SURFACE
1060
mm
WITH
127 mm
RISER
64 mm
762 mm
641 mm
OVERALL WIDTH
762 mm
Overall Height
(to cooking surface) 940 mm
Overall Depth
721 mm
Overall Oven
Interior Capacity
125 L
Overall Interior Dim
(W x H x D)
610 mm x 473 mm
x 432 mm
Usable Interior Dim
(W x H x D)
610 mm x 419 mm
x 432 mm
Opening Width
768 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Power Cord
1.8 m 3-prong
Shipping Weight
147 kg
1102 mm
LEGS AND CASTERS ALLOW
25 mm HEIGHT ADJUSTMENT
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S
MODEL OPTIONS
762 mm Gas Range
762 mm Gas Range
Four Surface
Burners
IR304
Natural gas model listed;
for LP gas add (-LP) to the
model number.
VENTILATION
HOOD
IMPORTANT NOTE: A
minimum 127 mm riser is
required when installing a
762 mm gas range against
a combustible surface.
762 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
330 mm
max
762 mm TO 914 mm
152 mm min
457 mm min
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
I N S TA L L AT I O N
TO COUNTERTOP
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
768 mm
FINISHED ROUGH
OPENING WIDTH
254
mm
203
mm
140 mm
914 mm
940 mm
305
mm
E
TO
COOKING
SURFACE
51
mm
G
305
mm
127 mm
76
LOCATION OF GAS SUPPLY EXTENDS
76 mm ON FLOOR FROM BACK WALL
mm
ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK
OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP –
0 mm TO NON-COMBUSTIBLE MATERIALS
49
WOLF GAS RANGES
OVERALL DIMENSIONS
914 mm Gas Range
S P E C I F I C AT I O N S
721 mm
OVERALL DEPTH
914 mm Gas Range
Overall Width
692 mm
914 mm
235
mm
Overall Height
(to cooking surface) 940 mm
Overall Depth
1441
mm
721 mm
Overall Oven
Interior Capacity
156 L
Overall Interior Dim
(W x H x D)
762 mm x 473 mm
x 432 mm
Usable Interior Dim
(W x H x D)
762 mm x 419 mm
x 432 mm
Opening Width
921 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated
circuit
Power Cord
1.8 m 3-prong
Shipping Weight
202–213 kg
WITH
508 mm
RISER
622 mm
1187
mm
940 mm
WITH
254 mm
RISER
914 mm
OVERALL
HEIGHT TO
COOKING
SURFACE
1060
mm
WITH
127 mm
RISER
64 mm
914 mm
641 mm
OVERALL WIDTH
1102 mm
LEGS AND CASTERS ALLOW
25 mm HEIGHT ADJUSTMENT
Unit dimensions may vary to ± 3 mm.
MODEL OPTIONS
I N S TA L L AT I O N S P E C I F I C AT I O N S
914 mm Gas Range
914 mm Gas Range
Four Surface Burners
Charbroiler
IR364C
Griddle
IR364G
Natural gas models listed;
for LP gas add (-LP) to the
model number.
VENTILATION
HOOD
IMPORTANT NOTE: A
minimum 254 mm riser is
required when installing a gas
range with a charbroiler or
griddle against a combustible
surface.
762 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
152 mm min
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
914 mm
min FOR
330 mm
max
762 mm TO 914 mm
CHARBROILER
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
457 mm min
TO COUNTERTOP
921 mm
FINISHED ROUGH OPENING WIDTH
254
mm
203
mm
140 mm
940 mm
305
mm
TO
COOKING
SURFACE
E
51
mm
G
305
mm
ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK
OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP –
0 mm TO NON-COMBUSTIBLE MATERIALS
50
914 mm
127 mm
76
LOCATION OF GAS SUPPLY EXTENDS
76 mm ON FLOOR FROM BACK WALL
mm
WOLF GAS RANGES
OVERALL DIMENSIONS
1219 mm Gas Range
S P E C I F I C AT I O N S
721 mm
OVERALL DEPTH
1219 mm Gas Range
692 mm
Overall Width
235
mm
1441
mm
WITH
508 mm
RISER
622 mm
1187
mm
940 mm
WITH
254 mm
RISER
914 mm
OVERALL
HEIGHT TO
COOKING
SURFACE
1060
mm
WITH
127 mm
RISER
64 mm
1219 mm
641 mm
OVERALL WIDTH
1219 mm
Overall Height
(to cooking surface) 940 mm
1102 mm
LEGS AND CASTERS ALLOW
25 mm HEIGHT ADJUSTMENT
Overall Depth
721 mm
Large Oven —
Overall Interior Cap
125 L
Overall Interior Dim
(W x H x D)
610 mm x 473 mm
x 432 mm
Usable Interior Dim
(W x H x D)
610 mm x 419 mm
x 432 mm
Small Oven —
Overall Interior Cap
71 L
Overall Interior Dim
(W x H x D)
343 mm x 473 mm
x 432 mm
Usable Interior Dim
(W x H x D)
343 mm x 419 mm
x 432 mm
Opening Width
1226 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated
circuit
Power Cord
1.8 m 3-prong
Shipping Weight
295–340 kg
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S
1219 mm Gas Range
MODEL OPTIONS
1219 mm Gas Range
Six Surface Burners
Charbroiler
IR486C
Griddle
IR486G
VENTILATION HOOD
Four Surface Burners
Charbroiler and
Griddle
IR484CG
762 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
152 mm min
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
762 mm TO 914 mm
COUNTERTOP TO
BOTTOM OF
VENTILATION HOOD
914 mm min
FOR CHARBROILER
330 mm
max
457 mm min
TO COUNTERTOP
IMPORTANT NOTE: A
minimum 254 mm riser is
required when installing a gas
range with a charbroiler or
griddle against a combustible
surface.
1226 mm
FINISHED ROUGH OPENING WIDTH
914 mm
940 mm
305
mm
660 mm
203
mm
140 mm
Natural gas models listed;
for LP gas add (-LP) to the
model number.
TO
COOKING
SURFACE
E
51
mm
G
305
mm
127 mm
76
LOCATION OF GAS SUPPLY EXTENDS
76 mm ON FLOOR FROM BACK WALL
mm
ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK
OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP –
0 mm TO NON-COMBUSTIBLE MATERIALS
51
WOLF GAS RANGES
OVERALL DIMENSIONS
1524 mm Gas Range
S P E C I F I C AT I O N S
721 mm
OVERALL DEPTH
1524 mm Gas Range
Overall Width
692 mm
1524 mm
235
mm
Overall Height
(to cooking surface) 940 mm
Overall Depth
1441
mm
721 mm
Overall Oven Interior
Capacity (per oven) 125 L
WITH
508 mm
RISER
622 mm
Overall Interior Dim
(W x H x D)
610 mm x 473 mm
x 432 mm each
Usable Interior Dim
(W x H x D)
610 mm x 419 mm
x 432 mm each
Opening Width
1530 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated
circuit
Power Cord
1.8 m 3-prong
Shipping Weight
397–431 kg
1187
mm
WITH
254 mm
RISER
940 mm 914 mm
OVERALL
HEIGHT TO
COOKING
SURFACE
1060
mm
WITH
127 mm
RISER
64 mm
1524 mm
641 mm
OVERALL WIDTH
1102 mm
LEGS AND CASTERS ALLOW
25 mm HEIGHT ADJUSTMENT
Unit dimensions may vary to ± 3 mm.
MODEL OPTIONS
I N S TA L L AT I O N S P E C I F I C AT I O N S
1524 mm Gas Range
1524 mm Gas Range
Four Surface Burners
Charbroiler and
Griddle
IR606CG
Natural gas models listed;
for LP gas add (-LP) to the
model number.
VENTILATION HOOD
IMPORTANT NOTE: A
minimum 254 mm riser is
required when installing a gas
range with a charbroiler or
griddle against a combustible
surface.
152 mm min
I N S TA L L AT I O N
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
1118 mm min
762 mm TO 914 mm
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
TO COUNTERTOP
1530 mm
FINISHED ROUGH OPENING WIDTH
914 mm
254
mm
203
mm
940 mm
305
mm
TO
COOKING
SURFACE
E
140 mm
ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK
OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP –
0 mm TO NON-COMBUSTIBLE MATERIALS
52
330 mm
max
457 mm min
51
mm
G
305
mm
127 mm
76
LOCATION OF GAS SUPPLY EXTENDS
76 mm ON FLOOR FROM BACK WALL
mm
WOLF GAS RANGETOPS
WOLF GAS RANGETOPS
If you want to offer a more professional look to
your client’s kitchen and still use a cooktop, look
to the rangetops from Wolf. They offer you that
commercial look but give you flexibility to use
the ovens in other locations in the kitchen. In
fact, the Wolf framed ovens would be a beautiful
complement to these cooking instruments.
Choose from four or six dual burners or consider
the Wolf exclusive infrared charbroiler, infrared
griddle or French Top for the ultimate in restaurant cooking in the home.
Wolf gas rangetops come in 914 mm and 1219
mm widths and are available in natural or LP
gas, with your choice of several top configurations. Model numbers indicate the top configurations: (C) charbroiler, (G) griddle and (F) French
Top.
All Wolf gas rangetops come in the classic
stainless steel finish and are shipped with the
distinctive red control knobs. Contact your Wolf
dealer for optional black knobs available at no
cost.
The dual burners can produce 4.7 kW for professional cooking heat or as little as .1 kW for
those delicate sauces.
G A S R A N G E T O P F E AT U R E S
T O P C O N F I G U R AT I O N S
Model IRT484CG shown with island trim
Gas Rangetops
Infrared charbroiler
(optional)
Infrared griddle
(optional)
Porcelain-coated
cast iron top grates
Low-profile
island trim
Dual brass
burners
IRT364C
IRT486C
IRT364G
IRT486G
Stainless steel
exterior finish
Location of
rating plate
Pull-out drip tray
Large red
control knobs
Griddle indicator
light
IRT484CG
ACCESSORIES
Gas Rangetops
267 mm classic stainless steel
riser
Classic stainless steel island trim
Black control knobs—available
at no cost
IRT484F
This appliance is certified by
Star-K to meet strict religious
regulations in conjunction with
specific instructions found on
www.star-k.org.
Porcelain-coated, cast iron wok
grate
Porcelain-coated, cast iron
two-burner S-grate
Hardwood cutting board—griddle
models only
Accessories are available through
your Wolf dealer.
53
WOLF GAS RANGETOPS
FEATURES
ELECTRICAL | GAS REQUIREMENTS
Natural or LP gas models
Specifications on the following pages provide
electrical and gas requirements for each size
of gas rangetop.
Fits standard 610 mm deep cabinets with zero
clearance for easy installation
Porcelain-coated cast iron top grates
International (I) models come with a factory
installed transformer and require a 220-240
V AC, 50/60 Hz electrical supply, fused at the
correct rating for the unit. The appropriate electrical connection must be provided in accordance
with local requirements. The service should have
its own 15 amp circuit breaker.
Large red control knobs with four position
settings and chrome bezels—optional black
knobs available
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
Stainless steel drip tray on ball bearing slides
Wolf gas rangetops are designed to operate on
natural gas at 12.5 mb WC (water column)
pressure or LP (propane) gas at 25 mb WC
pressure. The minimum line pressure for natural
gas is 17.5 mb WC and 27.4 mb WC for LP gas.
The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa.
Optional infrared charbroiler, infrared griddle
and French Top configurations
Classic stainless steel exterior finish
Dual brass burners with automatic reignition at
all settings, .1 kW simmer to 4.7 kW high
PLANNING INFORMATION
Wolf gas rangetops come in 914 mm and 1219
mm widths. Specifications on the following
pages provide overall dimensions, finished rough
opening dimensions and installation specifics for
each size of gas rangetop. We have minimized
the information contained in the illustrations,
concentrating on the critical information you
need to plan your installation.
IMPORTANT NOTE: Caution must be used in
planning the proper installation of the Wolf gas
rangetop to avoid fires or damage to adjacent
cabinetry or kitchen equipment. Follow the
minimum clearances established in the finished
rough opening dimensions. Refer to specifications on the following pages for your model.
Wolf recommends the use of a 13 mm I.D.
commercial-type flex hose; this is the minimum
size that may be used. All plumbing to the flex
hose must be 19 mm minimum I.D. pipe.
IMPORTANT NOTE: A separate external gas
shut-off valve must be located near the range
in an accessible location.
The platform for the rangetop must be 19 mm
thick and include a cut-out at the right rear for
gas supply and electrical connections.
Locate electrical and gas supply within the
shaded area shown in the Installation Specifications illustration for your model.
You must follow all local codes and ordinances
when installing your services.
B U R N E R R AT I N G
Gas Rangetops
Surface Burners
4.7 kW with .1 kW
delivered at simmer
Infrared Charbroiler
4.7 kW
Infrared Griddle
5.3 kW
French Top
4.4 kW
Refer to the specific model requirements
for risers in non-island installations.
54
WOLF GAS RANGETOPS
OVERALL DIMENSIONS
914 mm Gas Rangetop
S P E C I F I C AT I O N S
914 mm Gas Rangetop
692 mm
OVERALL DEPTH
TO KNOBS
COOKING
SURFACE
508 mm
WITH
267 mm
RISER
267 mm
241 mm
914 mm
Overall Width
914 mm
Overall Height
(to cooking surface) 267 mm
70 mm
OVERALL
HEIGHT
51 mm
Overall Depth
692 mm
Opening Width
921 mm
Opening Height
241 mm
(platform to countertop)
610 mm
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated
circuit
Power Cord
1.8 m 3-prong
Shipping Weight
86–100 kg
OVERALL WIDTH
Unit dimensions may vary to ± 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S
MODEL OPTIONS
914 mm Gas Rangetop
914 mm Gas Rangetop
Four Surface Burners
762 mm min
152 mm min
762 mm min
914 mm min
FOR CHARBROILER
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
TO 914 mm max
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
I N S TA L L AT I O N
241 mm
13 mm
E G
203
mm
203
mm
356 mm
LOCATION OF
GAS AND ELECTRICAL
SUPPLY CUT-OUT
WITHIN SHADED AREA
THROUGH BOTTOM OF
PLATFORM
IMPORTANT NOTE: In nonisland applications, a riser is
required when installing a
914 mm gas rangetop against
a combustible surface.
TO COUNTERTOP
OPENING
HEIGHT
BACK WALL
76 mm
330 mm
max
921 mm
TOP VIEW
OF PLATFORM
IRT364G
457 mm min
FINISHED ROUGH OPENING WIDTH
19 mm PLATFORM
IRT364C
Griddle
Natural gas models listed;
for LP gas add (-LP) to the
model number.
VENTILATION HOOD
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
Charbroiler
914
mm
19 mm PLATFORM
70
mm
Refer to installation
instructions shipped with
each Wolf product for
detailed specifications.
610 mm
ISLAND INSTALLATIONS: 305 mm MINIMUM
CLEARANCE FROM BACK OF RANGETOP TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0 mm TO NON-COMBUSTIBLE MATERIALS
55
WOLF GAS RANGETOPS
OVERALL DIMENSIONS
1219 mm Gas Rangetop
S P E C I F I C AT I O N S
1219 mm Gas Rangetop
692 mm
Overall Width
OVERALL DEPTH
TO KNOBS
1219 mm
Overall Height
(to cooking surface) 267 mm
Overall Depth
692 mm
Opening Width
1226 mm
COOKING
SURFACE
OVERALL
HEIGHT
220-240 V AC, 50/60 Hz
15 amp dedicated
circuit
Power Cord
1.8 m 3-prong
Shipping Weight
100–127 kg
70 mm
508 mm
WITH
267 mm
RISER
267 mm
Opening Height
241 mm
(platform to countertop)
Electrical Supply
51 mm
241 mm
1219 mm
610 mm
OVERALL WIDTH
Unit dimensions may vary to ± 3 mm.
MODEL OPTIONS
I N S TA L L AT I O N S P E C I F I C AT I O N S
1219 mm Gas Rangetop
1219 mm Gas Rangetop
Six Surface Burners
Charbroiler
IRT486C
Griddle
IRT486G
Four Surface Burners
Charbroiler and
Griddle
IRT484CG
French Top
VENTILATION HOOD
IRT484F
Natural gas models listed;
for LP gas add (-LP) to the
model number.
IMPORTANT NOTE: In nonisland applications, a riser is
required when installing a
1219 mm gas rangetop
against a combustible
surface.
762 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
762 mm min
TO 914 mm max
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
914 mm min
152 mm min
FOR CHARBROILER
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
1226 mm
241 mm
OPENING
HEIGHT
TOP VIEW
OF PLATFORM
13 mm
BACK WALL
E
TO COUNTERTOP
FINISHED ROUGH OPENING WIDTH
19 mm PLATFORM
76 mm
330 mm
max
457 mm min
G
406 mm
406 mm
356 mm
LOCATION OF GAS AND
ELECTRICAL SUPPLY CUT-OUT
WITHIN SHADED AREA
THROUGH BOTTOM OF
PLATFORM
914
mm
19 mm PLATFORM
70
mm
610 mm
ISLAND INSTALLATIONS: 305 mm MINIMUM
CLEARANCE FROM BACK OF RANGETOP TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0 mm TO NON-COMBUSTIBLE MATERIALS
56
WOLF COOKTOP VENTILATION
WOLF E SERIES COOKTOP HOODS
FEATURES
Behind the contemporary lines of the Wolf
E Series cooktop hoods, there's a lot of hardnosed functional thinking. Brilliant halogen
lighting illuminates your cooking surface.
Powerful multi-speed blowers whisk away
smoke and odors. Wall-mount hoods in three
widths and island hood are available in classic
stainless steel.
Classic stainless steel finish
E Series cooktop wall and island hoods are
recommended for use with Wolf electric and gas
cooktops and integrated modules.
Internal and remote blower options
Front-mounted electronic controls with digital
indicator
Heavy-duty stainless steel construction
Four-speed blower control
Model ICTEWH30I
Filter clean indicator lets you know when the
filter needs cleaning
Delay-off feature automatically turns unit off
Sealed halogen lighting with three settings
Stainless steel filter cover with dishwasher-safe
aluminum mesh filter
Heat sentry feature automatically turns unit on
when heat is sensed and automatically adjusts
blower speed
Model ICTEWH36I
Hood can be ducted to the outside or nonducted using a charcoal filter (internal blower
(I) models only)
Transition with back draft damper included
Fits 2.4 m to 2.7 m ceilings
Model ICTEWH45I
W O L F E S E R I E S C O O K T O P H O O D F E AT U R E S
Model ICTEWH36I shown
Model ICTEIH42I
Classic stainless
steel finish
Telescopic flue
Transition with
backdraft damper
(I) Models include 500
CFM Internal blower
Dishwasher-safe
filter
Filter clean
indicator
MODEL OPTIONS
E Series Cooktop Hoods
Wall Hoods
Four-speed
blower control
Location of
rating plate
Halogen lighting
Electronic controls
with digital indicator
762 mm Width
ICTEWH30I*
914 mm Width
ICTEWH36I
ICTEWH36I*
1143 mm Width
ICTEWH45I*
Island Hood
ICTEIH42I*
*500 CFM internal blower
included.
57
WOLF COOKTOP VENTILATION
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
Wolf E Series cooktop wall hoods are 450 mm
deep and come in 762 mm, 914 mm and 1143
mm widths. The island hood is 1067 mm wide
by 550 mm deep. (I) models include a 500 CFM
internal blower.
Wolf E Series cooktop wall and island hoods
require a separate, grounded 220-240 V AC,
50/60 Hz power supply with a dedicated 15 amp
circuit. Placement of the electrical supply is not
critical, as long as it is accessible
IMPORTANT NOTE: E Series cooktop wall and
island hoods are recommended for use with
Wolf electric and gas cooktops along with integrated modules, and should be at least as wide
as the cooking surface.
Locate electrical within the shaded area shown
in the Installation Specifications illustration for
your model.
Wolf E Series cooktop wall and island hoods
come with a telescopic flue that allows you to
reach a ceiling height of 2.4 m to 2.7 m with a
finished look.
Specifications on the following pages provide
overall dimensions, blower and ducting considerations, and installation specifics for cooktop
wall and island hoods. We have minimized the
information contained in the illustrations,
concentrating on the critical information you
must plan into your installation.
Installation of the cooktop wall or island hood
should be 650 mm to 760 mm from the bottom
of the hood to the countertop.
ACCESSORIES
E Series Cooktop Hoods
Internal and remote blower
assemblies
Charcoal filters for non-ducted
applications (internal blower
(I) models only)
Accessories are available through
your Wolf dealer.
58
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
You must follow all local codes and ordinances
when installing your service.
WOLF COOKTOP VENTILATION
OVERALL DIMENSIONS
E Series Cooktop Wall Hoods
Model ICTEWH30I
S P E C I F I C AT I O N S
250 mm
Model ICTEWH30I
274 mm
200 mm
TO
620 mm
Hood Type
Wall Hood
Overall Width
762 mm
Overall Height
80 mm
(excluding chimney)
790 mm
TO
1210 mm
510 mm
OVERALL
HEIGHT
80 mm
762 mm
450 mm
OVERALL WIDTH
OVERALL DEPTH
Models ICTEWH36 and ICTEWH36I
250 mm
274 mm
200 mm
TO
620 mm
790 mm
Overall Height
(including chimney)
790 mm
Maximum Height
(full extension)
1210 mm
Overall Depth
450 mm
Bottom of Hood
to Countertop
650 mm to 760 mm
Duct Size
150 mm Round
Discharge
Vertical
Internal Blower
500 CFM included
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Shipping Weight
(shell only)
18 kg
TO
1210 mm
510 mm
OVERALL
HEIGHT
S P E C I F I C AT I O N S
80 mm
914 mm
OVERALL WIDTH
450 mm
OVERALL DEPTH
Models ICTEWH36 and ICTEWH36I
Hood Type
Wall Hood
Overall Width
914 mm
Overall Height
80 mm
(excluding chimney)
Model ICTEWH45
250 mm
274 mm
200 mm
TO
620 mm
790 mm
TO
1210 mm
510 mm
OVERALL
HEIGHT
80 mm
1143 mm
OVERALL WIDTH
450 mm
OVERALL DEPTH
OVERALL DIMENSIONS
E Series Cooktop Island Hood — Model ICTEIH42
297 mm
Overall Height
(including chimney)
790 mm
Maximum Height
(full extension)
1210 mm
Overall Depth
450 mm
Bottom of Hood
to Countertop
650 mm to 760 mm
Duct Size
150 mm Round
Discharge
Vertical
Internal Blower
500 CFM included with
Model ICTEWH36I
Blower Options
Contact your
Wolf dealer
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Shipping Weight
(shell only)
21 kg
251 mm
222 mm
TO
*Blower options vary with the cooking
surface. Refer to the cooktop ventilation
recommendations on pages 68–69.
642 mm
790 mm
TO
1210 mm
488 mm
OVERALL
HEIGHT
80 mm
1067 mm
OVERALL WIDTH
550 mm
OVERALL DEPTH
59
WOLF COOKTOP VENTILATION
I N S TA L L AT I O N S P E C I F I C AT I O N S
E Series Cooktop Wall Hoods
S P E C I F I C AT I O N S
Model ICTEWH45I
Hood Type
Wall Hood
Overall Width
1143 mm
1210 mm
MAXIMUM
HEIGHT
OF HOOD
Overall Height
80 mm
(excluding chimney)
Overall Height
(including chimney)
790 mm
Maximum Height
(full extension)
1210 mm
Overall Depth
450 mm
Bottom of Hood
to Countertop
650 mm to 760 mm
Duct Size
150 mm Round
Discharge
Vertical
Internal Blower
500 CFM included
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Shipping Weight
(shell only)
26 kg
790 mm
MINIMUM
HEIGHT
OF HOOD
762 mm, 914 mm
OR 1143 mm
450 mm
OVERALL DEPTH
OVERALL WIDTH
2.4 m TO 2.7 m
650 mm
FLOOR TO
CEILING HEIGHT
TO
760 mm
TO COUNTERTOP
S P E C I F I C AT I O N S
Model ICTEIH42I
Hood Type
Island Hood
Overall Width
1067 mm
Overall Height
80 mm
(excluding chimney)
Overall Height
(including chimney)
790 mm
Maximum Height
(full extension)
1210 mm
Overall Depth
550 mm
Bottom of Hood
to Countertop
650 mm to 760 mm
Duct Size
150 mm Round
Discharge
Vertical
Internal Blower
500 CFM included
Electrical Supply
220-240 V AC, 50/60 Hz
15 amp dedicated circuit
Shipping Weight
(shell only)
32 kg
I N S TA L L AT I O N S P E C I F I C AT I O N S
E Series Cooktop Island Hood
1210 mm
MAXIMUM
HEIGHT
OF HOOD
790 mm
MINIMUM
HEIGHT
OF HOOD
550 mm
OVERALL DEPTH
1067 mm
OVERALL WIDTH
2.4 m TO 2.7 m
FLOOR TO
CEILING HEIGHT
650 mm
TO
760 mm
TO COUNTERTOP
60
WOLF COOKTOP VENTILATION
BLOWER CONSIDERATIONS
DUCTING CONSIDERATIONS
Except for Model ICTEWH36, which is shipped
without a blower assembly, E Series cooktop
hoods include a 500 CFM internal blower. Wolf
internal and remote blowers are available for
Model ICTEWH36. Models with an internal
blower can also use the charcoal filter if the
hood will not be ducted to the outside. Charcoal
filters are available as a sales accessory. Contact
your local Wolf dealer for more information on
remote blowers and charcoal filters.
IMPORTANT NOTE: E Series cooktop hoods can
be ducted to the outside or using a sales accessory charcoal filter, in a non-ducting installation
(internal blower (I) models only).
For Model ICTEWH36, the blower will vary in
size when ducted to the outside. Blower size is
dictated by the cooking surface, the volume of
air to be moved and the length of the duct run.
A straight, short duct run with a limited number
of elbows and transitions will allow the ventilation hood to perform most efficiently.
Wolf cooktop wall and island hoods have an
150 mm round vertical discharge. Ducting can
run through the roof, external wall or eave.
Ducting through an eave requires an internal
blower. Refer to the illustrations below.
E Series cooktop wall and island hoods will
operate most efficiently when ductwork does
not exceed 15 m in length.
Local building codes may require the use of
make-up air. Consult your local HVAC professional for specific requirements in your area.
A remote-mounted blower will minimize the
amount of blower noise, but will not eliminate
the noise completely. All remote blowers will
require a transition to a 254 mm duct.
D U C T I N G C O N S I D E R AT I O N S
E Series Cooktop Wall Hoods
E Series Cooktop Island Hood
DUCTWORK INSTALLATION
THROUGH ROOF
DUCTWORK INSTALLATION
THROUGH ROOF
ROOF CAP OR REMOTE BLOWER
ROOF CAP OR REMOTE BLOWER
150 mm ROUND DUCT
150 mm ROUND DUCT
WALL CAP
OR REMOTE BLOWER
790 mm
TELESCOPIC
CHIMNEY FLUE
TO
1210 mm
HEIGHT
OF HOOD
150 mm ROUND
ELBOW
150 mm ROUND
ELBOW
TELESCOPIC
CHIMNEY FLUE
790 mm
DUCTWORK INSTALLATION
THROUGH WALL
EAVE VENT
TO
1210 mm
HEIGHT
OF HOOD
150 mm ROUND
VERTICAL
DISCHARGE
150 mm ROUND
VERTICAL DISCHARGE
DUCTWORK
INSTALLATION
THROUGH
EAVE –
INTERNAL
BLOWER ONLY
80 mm
80 mm
450 mm
HOOD DEPTH
550 mm
OVERALL DEPTH
650 mm
650 mm
TO
760 mm
COUNTERTOP
TO BOTTOM
OF HOOD
TO
760 mm
COUNTERTOP
TO BOTTOM
OF HOOD
61
WOLF COOKTOP VENTILATION
Model DD30
Model DD36
WOLF DOWNDRAFT SYSTEMS
FEATURES
The cooktop downdraft unit rises from the countertop to whisk away odors and smoke into the
easy-to-clean, five-layer mesh filter. The control
module and top cover are available in classic
stainless steel.
Classic stainless steel control module and top
cover
Wolf downdraft systems come in 762 mm,
914 mm and 1143 mm widths and are recommended for use with Wolf framed electric
cooktops, gas cooktops and integrated modules.
IMPORTANT NOTE: Wolf downdraft ventilation
systems are not recommended for use with the
electric grill, steamer and fryer modules.
Model DD45
A downdraft can be used with sealed burner
rangetop Model ICBSRT304. An accessory trim
kit is necessary for this installation. Contact your
Wolf dealer for details.
Remote-mounted control module
Internal, in-line and remote blower options
Three-speed blower control
Filter clean timer lets you know when the filter
needs cleaning
Delay-off feature automatically turns unit off
after five minutes, chimney remains up
Stainless steel filter cover with dishwasher-safe
aluminum mesh filter
LED indicators
Downdraft control kit, available as a sales
accessory for Models DD30 and DD36 (included
with Model DD45)—includes control module, top
cover, mounting brackets, RJ45 connector and
mounting hardware
D O W N D R A F T S Y S T E M F E AT U R E S
Model DD36 shown
MODEL OPTIONS
Downdraft Systems
229 mm chimney
elevation
Top cover
(I) Models
500 CFM internal blower included
Three-speed
blower control
762 mm Width
DD30I
914 mm Width
DD36I
1143 mm Width
DD45I
(R) Models
Remote blower required
Remote-mounted
control module
Aluminum mesh
filters
Stainless steel
filter covers
762 mm Width
DD30R
914 mm Width
DD36R
1143 mm Width
DD45R
Location of
rating plate
CONTROL KIT OPTIONS
Downdraft Systems
ACCESSORIES
Downdraft Systems
Model DD30I / DD30R
Classic
Bracket supports for installation
of two integrated modules with
762 mm downdraft
SRT/Downdraft trim kit for
sealed burner rangetop Model
ICBSRT304
Transitions in various sizes
Accessories are available through your
Wolf dealer.
62
DD30CONTROL/S
Model DD36I / DD36R
Classic
DD36CONTROL/S
Control module and top cover have the
stainless steel finish. Control kits also
include mounting brackets, RJ45 connector and hardware and are ordered and
shipped as sales accessories for Models
DD30 and DD36. Control kit components
are included with Model DD45.
WOLF COOKTOP VENTILATION
PLANNING INFORMATION
Wolf downdraft ventilation systems are available
in 762 mm, 914 mm and 1143 mm widths. The
downdraft should be at least as wide as the
cooking surface.
Downdraft Model DD30 will fit most 762 mm
wide cabinets, Model DD36 will fit most 914 mm
wide cabinets and Model DD45 will fit most
1156 mm wide cabinets. It is recommended that
oversized cabinets be used for easier installation.
Cabinet backs may need to be removed.
Specifications on the following pages provide
overall dimensions, blower and ducting considerations, and installation specifics for downdraft
ventilation systems. Also refer to the cooktop
ventilation recommendations on pages 68–69.
If a Model DD30 is installed in combination with
two integrated modules, an integrated module
support for downdraft ventilation is required.
Contact your Wolf dealer for information on
accessory components.
IMPORTANT NOTE: To install a downdraft
system and a Wolf cooktop, you must allow for
a minimum 638 mm flat counter space from
front to back. A countertop with a raised lip
and/or backsplash may not allow enough space
for proper installation. 60 mm of flat countertop
is required behind the cooktop and 44 mm is
necessary between the back edge of the
cooktop and inside of cabinet back.
I N S TA L L AT I O N
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
IMPORTANT NOTE: This appliance must be
used with a Wolf-approved control module and
top cover.
The remote-mounted control module is available
as a sales accessory for Models DD30 and DD36
and is included with Model DD45. Installation of
the control module must be within 3 m of the
downdraft assembly and a minimum of 102 mm
from the outer edge of cooktop element or
burner. You will be required to drill three holes
and connect the downdraft to the control
module with the provided wire.
OVERALL DIMENSIONS
Downdraft Systems
Models DD30I / DD30R
762 mm
Models DD36I / DD36R
230 mm
230 mm
819 mm
667 mm
1156 mm
60 mm
914 mm
60 mm
Models DD45I / DD45R
38 mm
38 mm
DEPTH OF
DOWNDRAFT CHIMNEY
DEPTH OF
DOWNDRAFT CHIMNEY
230 mm
60 mm
1048 mm
38 mm
DEPTH OF
DOWNDRAFT CHIMNEY
63
WOLF COOKTOP VENTILATION
I N S TA L L AT I O N S P E C I F I C AT I O N S
Downdraft Systems
S P E C I F I C AT I O N S
Models DD30I / DD30R
Overall Width
762 mm
Overall Height
(above countertop)
230 mm
Overall Depth
60 mm
Duct Size (DD30I)
83 mm x 254 mm
Duct Size (DD30R)
83 mm x 356 mm
Discharge
Adjustable
Blower (DD30I)
500 CFM Internal
Blower Options*
(DD30R)
1100 CFM In-Line,
900, 1200 or 1500 CFM
Remote
Electrical Supply
220-240 V AC, 60 Hz
15 amp dedicated circuit
Power Cord
.8 m 3-prong
Shipping Weight
34 kg
638 mm min
44 mm min
BACK EDGE
OF COOKTOP
TO INSIDE OF
CABINET BACK*
OF FLAT COUNTERTOP*
16 mm
8.7 mm
489 mm
64 mm min
COOKTOP CUT-OUT
DEPTH
WITH NO
RAISED LIP*
60 mm
197 mm
54 mm
83 mm
745 mm
COUNTERTOP
TO BOTTOM OF
AIR BOX
92
mm
127
mm
914 mm
457
mm
S P E C I F I C AT I O N S
Models DD36I / DD36R
Overall Width
914 mm
Overall Height
(above countertop)
230 mm
Overall Depth
60 mm
Duct Size (DD36I)
83 mm x 254 mm
Duct Size (DD36R)
83 mm x 356 mm
Discharge
Adjustable
181 mm
610 mm min
CABINET DEPTH
*AREAS OF POTENTIAL INTERFERENCE
Blower (DD36I)
500 CFM Internal
Blower Options*
(DD36R)
1100 CFM In-Line,
900, 1200 or 1500 CFM
Remote
Electrical Supply
220-240 V AC, 60 Hz
15 amp dedicated circuit
Power Cord
.8 m 3-prong
Shipping Weight
36 kg
70 mm
686 mm
FOR MODEL DD30
838 mm
638 mm min
FOR MODEL DD36
FLAT
COUNTERTOP
SPACE
FOR MODEL DD45
1067 mm
489 mm
COOKTOP CUT-OUT
WIDTH
64 mm min
COUNTERTOP TOP VIEW
S P E C I F I C AT I O N S
Models DD45I / DD45R
Overall Width
1156 mm
Overall Height
(above countertop)
230 mm
Overall Depth
60 mm
Duct Size (DD45I)
83 mm x 254 mm
Duct Size (DD45R)
83 mm x 356 mm
Discharge
Adjustable
Blower (DD45I)
500 CFM Internal
Blower Options*
(DD45R)
1100 CFM In-Line,
900, 1200 or 1500 CFM
Remote
Electrical Supply
220-240 V AC, 60 Hz
15 amp dedicated circuit
Power Cord
.8 m 3-prong
Shipping Weight
39 kg
*Refer to the cooktop ventilation
recommendations on pages 68–69.
64
WOLF COOKTOP VENTILATION
ELECTRICAL REQUIREMENTS
BLOWER CONSIDERATIONS
Wolf downdraft ventilation systems require a
separate, grounded 120 V AC, 60 Hz power
supply. The service should have its own 15 amp
circuit breaker, and a grounded 3-prong receptacle should be located within the reach of the
.8 m power cord. The specific location of the
outlet is not critical as long as it is within reach
of the power cord that is located midway, top
and bottom, on the right side of the downdraft.
Except for Models DD30I, DD36I and DD45I,
which include a 500 CFM internal blower, Wolf
downdrafts are shipped without the blower
assembly. In-line and remote blower assemblies
are available. The blower will vary in size and is
dictated by the cooking surface, the volume of
air that needs to be moved and the length of the
duct run. A straight, short duct run with a
limited number of elbows and transitions will
allow the ventilation hood to perform most efficiently.
IMPORTANT NOTE: If Model DD30 is to be
installed in a 762 mm wide cabinet, Model DD36
in a 914 mm wide cabinet or Model DD45 in a
1156 mm wide cabinet, the electrical outlet
cannot be located on the back wall of the
cabinet. The outlet may be placed in adjacent
cabinetry.
Locate electrical within the shaded area shown
in the Installation Specifications illustrations.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
You must follow all local codes and ordinances
when installing your service.
Wolf downdraft ventilation systems are designed
for use with 83 mm x 254 mm ductwork for
Models DD30I, DD36I and DD45I and 83 mm x
356 mm ductwork for Models DD30R, DD36R
and DD45R. Each can be transitioned to 203 mm
or 254 mm round ductwork.
I N S TA L L AT I O N
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
A remote-mounted blower will minimize the
amount of blower noise, but will not eliminate
the noise completely.
IMPORTANT NOTE: Install this downdraft
system only with a Wolf blower.
Refer to the cooktop ventilation recommendations on pages 68–69.
I N S TA L L AT I O N S P E C I F I C AT I O N S
Location of Electrical Supply
610 mm min
102 mm min
89 mm
E
E
254 mm
CABINET DEPTH
762 mm min
FOR MODEL DD30
914 mm min
FOR MODEL DD36
1156 mm min
FOR MODEL DD45
OPTIONAL
ELECTRICAL
LOCATION IN
ADJACENT RIGHT
SIDE CABINET
IMPORTANT NOTE:
Certain installations
may require that the
electrical supply be
placed in an adjacent
cabinet within reach of
the power cord.
Choose the location
shown in the illustration that best suits
your installation.
65
WOLF COOKTOP VENTILATION
DUCTING CONSIDERATIONS
Wolf downdraft systems have an adjustable
discharge that will allow you to negotiate
ducting around floor joists and other obstacles.
Three different discharge locations are available
with side-to-side adjustment for accurate alignment of ductwork. Refer to the illustration below
for discharge location and adjustment.
Choose the ducting option that allows the
shortest length of ductwork and a minimum
number of elbows and transitions. Refer to the
illustration below for ducting options.
IMPORTANT NOTE: All Wolf downdraft systems
must be vented to the outside. Use only metal
ductwork.
For best performance, 254 mm round ductwork
is recommended. The downdraft will operate
most efficiently when ductwork does not exceed
12 m in length.
D I S C H A R G E L O C AT I O N
DUCTING OPTIONS
Downdraft Systems
Downdraft Systems
416 mm
CENTERLINE OF COUNTERTOP CUT-OUT
INTERNAL BLOWER
546 mm
IN-LINE OR
REMOTE BLOWER
CL
254 mm
ROUND
REMOTE
BLOWER
RIGHT
DISCHARGE
LOCATION
562 mm
INTERNAL BLOWER
483 mm
IN-LINE OR
REMOTE BLOWER
140 mm
INTERNAL BLOWER
WALL CAP
108 mm
LEFT
DISCHARGE
LOCATION
IN-LINE OR
REMOTE BLOWER
305 mm
DISCHARGE CUT-OUT
DIMENSIONS:
MIN TO
GROUND
260 mm x 89 mm
INTERNAL BLOWER
INTERNAL BLOWER
INSTALLATION THROUGH WALL
362 mm x 89 mm
REMOTE BLOWER
ROOF MOUNT INSTALLATION
IN-LINE OR
REMOTE BLOWER
CENTERLINE OF COUNTERTOP CUT-OUT
REMOTE
BLOWER
CL
ADJUSTMENT:
254 mm
ROUND
25 mm – 178 mm
INTERNAL BLOWER
165 mm MAX
IN-LINE OR
REMOTE BLOWER
305 mm
ADJUSTMENT:
140 mm
127 mm MAX
INTERNAL BLOWER
IN-LINE OR
REMOTE BLOWER
BOTTOM
DISCHARGE
LOCATION
305 mm
MIN TO
GROUND
108 mm
IN-LINE OR
REMOTE BLOWER
NOTE: Measurements are to centerline of duct cut-outs
66
MIN TO
GROUND
INTERNAL BLOWER
INSTALLATION THROUGH WALL
REMOTE BLOWER
INSTALLATION THROUGH WALL
WOLF VENTILATION RECOMMENDATIONS
WOLF BLOWER ASSEMBLIES
A ventilation system must include a blower
assembly. An internal, in-line or remote blower
assembly must be selected to accommodate the
cooking appliance, CFM requirements and homeowner preferences. Internal, in-line and remote
blower assemblies are available as sales accessories through your Wolf dealer.
Remote blowers can be mounted on the roof or,
in some cases, on an exterior wall. A remotemounted blower will minimize the amount of
blower noise but will not eliminate the noise
completely.
Internal blowers are mounted inside the hood
canopy or downdraft blower box.
Cooktop ventilation recommendation charts on
pages 68–69 provide minimum CFM recommendations according to the cooking appliance and
ventilation system used and blower options for
each specific downdraft.
Wolf internal, in-line and remote blowers are for
use with Wolf downdraft systems.
Wolf in-line blowers are mounted between the
downdraft and the exterior of the home. Ducting
runs from the downdraft and connects to the
blower. More ducting is attached to the other
side of the blower and runs to the exterior of the
home. An in-line blower is a good option for
those who do not want the blower mounted
inside the downdraft but cannot, or prefer not
to, mount a remote blower on the exterior of the
home.
Refer to the illustrations below for dimensions of
Wolf in-line and remote blowers. Installation
instructions shipped with each Wolf ventilation
product provide detailed specifications. These
instructions can also be found on our website,
wolfappliance.com.
IN-LINE BLOWER
ACCESSORIES
Blower assemblies
are available
through your Wolf
dealer.
REMOTE BLOWERS
533 mm
632 mm
718
mm
457
mm
305
mm
203
mm
749
mm
254 mm
Diameter
394
mm
559 mm
254
mm
527 mm
375
mm
622
mm
121
mm
629 mm
BLOWER-110IL
749
mm
264
mm
356
mm
457 mm
254 mm
Diameter
BLOWER-60REM and
BLOWER-90REM
635 mm
184
mm
BLOWER-150REM
457 mm
254
mm
749
mm
254 mm
Diameter
375
mm
749
mm
257
mm
559 mm
184
mm
BLOWER-120REM
67
WOLF VENTILATION RECOMMENDATIONS
COOKTOP VENTILATION CFM RECOMMENDATIONS
DOWNDRAFTS
DD30
DD36
DD45
Electric Cooktops
Model ICT15E
215*
Model ICT30E
500
Model ICT36E
150*
350
500
CFM
DD30
Recommendations
are based on total
kW output. Wolf
recommends 1 CFM
per .03 kW.
Additional CFM may
be required for charbroilers, griddles and
long duct runs.
DD36
Model ICBCT15G
215*
150*
Model ICBCT30G
500
350
Model ICBCT36G
500
DD30
DD36
DD45
Integrated Modules
Model CT15I
215*
150*
Model IIM15
215*
150*
DD30
DD36
Sealed Burner Rangetops
Model ICBSRT304
600
*Use these recommendations to determine total CFM when installing multiple cooktops or modules.
68
DD45
Gas Cooktops
DD45
WOLF VENTILATION RECOMMENDATIONS
COOKTOP VENTILATION BLOWER OPTIONS
DOWNDRAFT SYSTEMS
Blower Description
500 CFM Internal
Blower Number
Downdraft Models
Included with (I) Models
DD30I / DD36I / DD45I
BLOWER-110IL (808332)
DD30R / DD36R / DD45R
BLOWER-90REM (801641)
DD30R / DD36R / DD45R
1200 CFM Remote
BLOWER-120REM (801642)
DD30R / DD36R / DD45R
1500 CFM Remote
BLOWER-150REM (804701)
DD30R / DD36R / DD45R
1100 CFM In-Line
900 CFM Remote
Adjustable discharge. 83 mm x 254 mm duct for internal blower, no transition required. 83 mm x 356 mm duct for
in-line and remote blowers. TRANS-14-10 required for remote blowers.
IMPORTANT
NOTE
Blower configurations
are for reference
only. Refer to the
minimum CFM recommendations for your
specific cooking
appliance. Consult a
qualified HVAC
engineer for specific
installation and
ducting applications.
69
The information and images in this guide are the
copyright property of Wolf Appliance, Inc., an
affiliate of Sub-Zero, Inc. Neither this book nor any
information or images contained herein may be
copied or used in whole or in part without the
express written permission of Wolf Appliance, Inc.,
an affiliate of Sub-Zero, Inc.
70
©Wolf Appliance, Inc. all rights reserved.
71
WOLF APPLIANCE, INC.
P O BOX 44848
MADISON, WI 53744 USA
WOLFAPPLIANCE.COM
810295
8/ 2007