VTC-IRE24F
Day/Night 960H Infrared
Bullet Camera
VITEK
• 1/3” High Resolution CCD
• 700 TV Lines of Resolution (960H)
• E-WDR by Adaptive Tone Reproduction
• 24 Dynamic Infrared LEDs with up to 65’ Range
• 0.003 Lux / 0 Lux with IR LEDs On
• IR Corrected 3.6mm Fixed Iris Lens
• 2DNR Noise Reduction
• Motion Detection, Privacy Masking & Highlight Masking
• OSD (On Screen Display) menu and Camera ID
• IP-67 Rated Water Resistance
• Cable Feed Through Mount for tamper resistance
• 12 VDC Operation
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
CAUTION:
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we
have been advised of the possibility of such damages.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
PACKAGE CONTENTS
1 x VTC-IRE24F Camera
1 x Mounting Bracket
1 x User Manual
1 x Hex Wrench
1 x Mounting Screws/Anchors Pack
1 x Mounting Template
CONNECTION
1. Connect the camera video output to the monitor video input with a 75Ω coaxial
cable.
2. DC12V Input Terminal
Connect the power connector of the camera to a 12V DC regulated power supply.
NOTE: Please use the correct power adaptor, DC12V (regulated), to operate this
unit. The tolerance of this unit is DC12V ± 10%. Over the maximum DC12V power
input will damage the video output connector (VIDEO OUT).
VTC-BRE24F / VTC-IRE24F
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of non-insulated
dangerous voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
This installation should be made by a qualified service person and should conform to all local codes.
1
VTC-BRE24F / VTC-IRE24F
Contents
1.
EXPOSURE
2.
DAY & NIGHT
3.
WHITE BAL
4.
MONITOR
5.
IMAGE
6.
DNR
7.
MOTION
8.
SYSTEM
9.
EXIT
2
VTC-BRE24F / VTC-IRE24F
Warning
Contact an authorized technician for inspection.
If you use your camera around smoke or unusual heat for a long time, fire may
be caused.
Unless the surface is suitable, it could cause falling or other hazards.
It may result in fire, electric shock or other hazards.
It could cause an electric shock.
It
may result in fire or other hazards.
3
VTC-BRE24F / VTC-IRE24F
[OSD Menu]
EXPOSURE
DAY / NIGHT
WHITE BAL
MONITOR
IMAGE
DNR
MOTION
SYSTEM
EXIT
ALC / ELC
DAY / NIGHT / AUTO / EXTERNAL / CDS
MANUAL / PUSH / ATW
GAMMA / CHROMA / SHARPNESS / SHADING / PED.LV
BACK LIGHT / CONTRAST / POSI/NEGA / H-MIRROR /
PRIVACY
LOW / MIDDLE / HIGH / OFF
ON / OFF
CAM TITLE / CAM ID / ID DISP / SYNC / BAUDRATE /
LANGUAGE / SPECIAL
SAVE / MANUAL / INITIAL / RESTORE
How to use OSD button(Tact Switch) in OSD control board or OSD cable
Press : enter into OSD menu and save settings at EXIT.
Push UP / DOWN : select function wish to activate.
Push LEFT / RIGHT : adjust level / value and mode of sub-menu
OSD Main Menu
4
VTC-BRE24F / VTC-IRE24F
MAIN MENU
DEFAULT
EXPOSURE
DAY&NIGHT
WHITE BAL
ATW
MONITOR
IMAGE
DNR
MOTION
SYSTEM
EXIT
OFF
OFF
DESCRIPTION
Select Lens type according to mounted
/ built-in lens.
* ELC : Electronical Iris Lens
(Manual Iris Lens / Fixed Focal Lens).
* ALC: Auto Iris Lens(DC)
* AUTO: DAY or NIGHT is decided
automatically by light level coming through
lens.
* DAY: Color video output
* NIGHT: B/W video output regardless of
light level
* EXT: Day(Color) or Night(B/W) is decided by
external light sensor or LED control board
All IR LED cameras should set EXT.
* CDS: Not used
* ATW (Auto Tracking White Balance)
* MANUAL: Adjust White Balance with
fixed values of BLUE and RED
* PUSH: White Balance is performed when
enter button of OSD is pressed
* Set GAMMA, CHROMA, SHARPNESS,
SHADING & PED. LEVEL of Monitor
* BACK LIGH: Select HLC or BLC and adjust it.
* Select CONTRAST ON or OFF
* POSI / NEGA: Select Posi or Nega image.
* H-MIRROR: Select MIRROR ON or OFF
* PRIVACY: Set PRIVACY ON or OFF
Set DNR level, LOW or MIDDLE or HIGH
Select MOTION ON or OFF
Set CAM TITLE, CAM ID, ID DISP, SYNC,
BAUDRATE, LANGUAGE and SPECIAL
SAVE, MANUAL, INITIAL, RESTORE
5
VTC-BRE24F / VTC-IRE24F
1. EXPOSURE
Select lens type in accordance with mounted/built-in lens.
* ALC : Auto Iris Lens
* ELC : Electronic Iris Lens
(Fixed Focal Lens / Manual Iris Vari-focal Lens)
EXPOSURE
(ALC / ELC)
DEFAULT
BRIGHTNESS
SHUTTER
AUTO
FLK
OFF
AGC
20
DESCRIPTION
Adjust the brightness level of screen when the
environment is extremely bright or dark.
Adjustable shutter speed. This is useful when
the light condition is changing quickly
* Set AUTO, 1/50 ~ 1/120K
Select FLICKERLESS ON or OFF. In the FLK
ON, sensitivity will be reduced under low light
Setting AGC level, 0 ~ 20. The higher gain
level, brighter picture with more noise.
2. DAY & NIGHT
DAY &
NIGHT
DAY &
NIGHT
DEFAULT
IR LED
CAMERA : EXT
NONE IR
CAMERA :
AUTO
DESCRIPTION
* AUTO: Camera decide DAY or NIGHT by
himself through incoming light level.
ICR is also moving DAY or NIGHT (ICR
Version).
* DAY: Camera works as a regular color
camera.
ICR is inserted to cut IR spectrum from light
(ICR built-in Camera)
6
VTC-BRE24F / VTC-IRE24F
DAY &
NIGHT
DEFAULT
DESCRIPTION
* NIGHT: Camera works as a regular B/W camera.
ICR move to pass IR spectrum.
* CDS : Not used
* EXT : DAY or NIGHT is decided by external
signal(included CDS sensor) built in camera.
All of IR LED Cameras must be set to EXT.
DAY &
NIGHT
2-1. AUTO
Usually cameras with no IR LED is set AUTO. But IR LED cameras should set
EXT.
AUTO
AGC THRS
DEFAULT
11
AGC
MARGIN
D/N DELAY
3SEC
B/W BURST
OFF
SMART IR
DESCRIPTION
* Setting threshold level to switch from to DAY <-->
NIGHT.
* Setting threshold margin to switch from to DAY
<--> NIGHT.
* If AGC margin is too small, may occur switching
D <--> N repeatly. Recommend more than 10
* Dwell time before switch D <--> N after check
light level. * DELAY can avoid unnecessary
switching by short term light.
* To make right switch D <--> N, camera should
retain the present environment for longer than
DELAY(DWELL TIME).
* Select BURST ON or OFF
* Not used (Camera with no IR LED set Auto and
no need SMART IR)
7
VTC-BRE24F / VTC-IRE24F
8
VTC-BRE24F / VTC-IRE24F
2-2. NIGHT
NIGHT
BURST
DEFAULT
OFF
SMART IR
OFF
DESCRIPTION
* Select BURST ON or OFF
* Set LED POWER, ANTI-SAT & SAT AREA.
Can set SAT AREA when use ANTI-SAT.
Note: If set D&N at Night, White Balance is not activated.
2-3. EXT
EXT
EXTERN
S/W
DEFAULT
D/N
DELAY
3SEC
B/W
BURST
OFF
DESCRIPTION
* Must keep HIGH (IR LED Cameras only).
If use LOW, picture changes to B/W.
* Dwell time before switch D <--> N after check
light level.
* DELAY can avoid unnecessary switching by
short term light.
* To make right switch D <--> N, camera should
retain the present environment for longer than
DELAY(DWELL TIME).
* Select BURST ON or OFF
* Set LED POWER, ANTI-SAT & SAT AREA.
Can set SAT AREA when use ANTI-SAT.
SMART IR
3. WHITE BAL
WHITE BAL
WHITE BAL
DEFAULT
DESCRIPTION
ATW
* ATW(Auto Tracking White Balance)
* MANUAL: Adjust White Balance with fixed values
of BLUE and RED. User can adjust the color and
temperature by controlling RED and BLUE gain
Recommend to use when the light temperature is
fixed all the time.
* PUSH: Use when White Balance is deviated.
Press Enter(Set) button. White Balance is
performed whenever the enter(set) button is
pressed
9
VTC-BRE24F / VTC-IRE24F
4. MONITOR
* Set GAMMA, CHROMA, SHARPNESS, SHADING & PED. LEVEL of Monitor
5. IMAGE
5-1. BACK LIGHT
5-1-1 BLC
10
VTC-BRE24F / VTC-IRE24F
BLC
LEVEL
DEFAULT
MIDDLE
DESCRIPTION
DISPLAY
* Set up BLC LEVEL, MIDDLE, HIGH or OFF
* Select ON or OFF of BLC area.
BLC area appear in blue square frame.
TOP/BOT
TOM
* Adjust size of BLC area by moving
TOP / BOTTOM / LEFT / RIGHT menu.
BLC is useful function to see outside from inside under the environment bright
background of the object
BLC ON
BLC OFF
5-1-2 HLC : HLC cut out highlighted area then mask it with black color. Can
set HLC level
HSBLC ON
HSBLC OFF
5-2. CONTRAST
Set D-WDR & DEFOG or OFF
5-2-1 D-WDR
D-WDR
DEFAULT
DESCRIPTION
D-WDR
* Selectable AUTO or MANUAL
LEVEL
* Set D-WDR level, LOW / MIDDLE / HIGH
11
VTC-BRE24F / VTC-IRE24F
5-2-2 DEFOG
5-2-3 POSI / NEGA
Selectable POSI or NEGA image.
5-2-4 H-MIRROR
Selectable MIRROR ON or OFF
5-2-5 PRIVACY
This helps you can mask areas you not want to see but want to hide on
the screen, offering total 8 masking zones.
PRIVACY
DEFAULT
DESCRIPTION
MASK LV
* Can select a masking color for each masking
area out of the 12 colors
AREA NO
* Selectable up to 8 area
DISPLAY
* Select ON or Off. ON --> Display the selected
masking area
TOP/
BOTTOM
* Adjust size of selected masking area
12
VTC-BRE24F / VTC-IRE24F
6. DNR
DNR(Digital Noise Reduction) is technology useful at low light.
But too strong reduction may occur tail effect and loss sharpness.
* Can choose DNR level, LOW / MIDDLE / HIGH
7. MOTION
Motion Detection allows to observe moving object in 4 different areas on the
screen. Programmable Area No, Size, position, sensitivity and display ON or
OFF
Note : When detect something, display “MOTION ! ! !” on the monitor.
MOTION
SENSITIVITY
AREA NO
DEFAULT
DESCRIPTION
* Set sensitivity of detection
* Selectable detection area up to 4 ares.
AREA USE
* Determines whether use the selected area or not
TOP /
BOTTOM..
* Adjust size of selected area.
13
VTC-BRE24F / VTC-IRE24F
8. SYSTEM
SPECIAL
CAM TITLE
DEFAULT
OFF
DESCRIPTION
* Can make camera name up to 8 letters by
using UP / DOWN button
Can use 0~9 & A~Z
* LEFT / RIGHT button : choose lettering posion
* ON: Camera name(camera title) is displayed
on left top of the screen
CAM ID
* Set camera ID No. up to 256 from 0 to 255
ID DISP.
* On : Camera ID No. is displayed on right top
of the screen
* Fixed INT(Internal Sync)
SYNC
BAUDRATE
* Set Baud Rate, 2400 / 4800 / 9600 / 57600
/ 115200
LANGUAGE
* Available ENGLISH / CHINESE
SPECIAL
* Detect and compansate defective pixel.
* Selectable Font color of OSD Menu
(support total 8 colors)
14
VTC-BRE24F / VTC-IRE24F
8-1. CAM TITLE
*Can input max. 8 letters with A~Z & 0~9 by using UP / DOWN button.
*LEFT / RIGHT: move CAM TITLE input position
Note) If ‘OFF’ is selected, the CAM TITLE does not appear on the
monitor even if it has been inputted.
9. EXIT
SAVE: Save all of adjusted(changed) value
RESTORE: Return to before setting
INITIAL: Return to factory default
MANUAL: Keep changed data & value but not saved. After turn off then turn
on, return to before setting value.
15
Detailed Specifications
Image Device
Resolution
Effective Pixels
Minimum illumination
Infrared LEDs
IR Distance
Day/Night
Built-In Lens
Light Compensation
Noise Reduction
White Balance
E-WDR
Motion Detection
Privacy Mask
Water Resistance
Power Source
Operating Conditions
Dimensions
VTC-IRE24F
1/3” High-Resolution Inter-Line CCD (960H)
700 TVL (960H)
976(H) x 494(V)
0.003 Lux (0 Lux with LED ON)
24 Dynamic IR LEDs
65’ (20m)
Auto
3.6mm IR Corrected Lens
HLC (Highlight Compensation) / BLC (Backlight Compensation)
2DNR
ATW / AWB / Push
YES by ATR (Adaptive Tone Reproduction)
YES
Up to 8 Programmable Mask Areas
IP67
DC12V (±10%)
14°F to +140°F (-10°C to +60°C) @ 85% RH
2.80” x 7.09” x 2.58” (71 x 180 x 65.5mm)
VITEK LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants
to the purchaser that products manufactured by VITEK are free of
any rightful claim of infringement or the like, and when used in the
manner intended, will be free of defects in materials and workmanship
for a period of three (3) years, or as otherwise stated above, from the
date of purchase by the end user. This warranty is non-transferable
and extends only to the original buyer or end user customer of a Vitek
Authorized Reseller.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.
The product must not have been tampered with in any way then the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
Vitek makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a Vitek
Authorized Reseller.
28492 Constellation Road Valencia, ca 91355
WWW.VITEKCCTV.COM | 888-VITEK-70