Zibro SRE 130 TC Specifications

SRE 130 TC
3
MANUEL D'UTILISATION
2
2
GEBRAUCHSANWEISUNG
12
6
BRUGSANVISNING
22
5
INSTRUCCIONES DE USO
32
4
OPERATING MANUAL
42
>
ISTRUZIONI D’USO
52
1
GEBRUIKSAANWIJZING
62
Dear Sir, Madam,
Congratulations with your purchase of a portable domestic heater. You have
purchased a quality product, which will serve you for many years to come. This,
of course, provided you use the heater correctly. Please read these Directions
for Use first, to ensure maximum lifetime for your heater.
Your heater comes with a 24-month manufacturer’s warranty on all defects in
materials or workmanship.
We wish you a warm and comfortable time with your heater.
Yours sincerely,
PVG International b.v.
Customer Service Department
1 READ THE DIRECTIONS FOR USE FIRST.
2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.
3 BEFORE YOU START READING, FOLD OUT THE LAST PAGE.
4
42
E
E
E
E
E
E
E
E
E
E
GENERAL DIRECTIONS FOR USE
MAIN COMPONENTS
Below you will find the main steps to be taken for
using your heater. For more details, please refer to
A
Front plate
B
Grid
C
Base plate
4
Lid for removable
the MANUAL (pages 45 ff.).
1
2
3
4
Remove all packaging materials (refer to Section A, Fig. A).
tank
Fill the removable tank 7 (refer to Section B, Fig. C).
Insert the plug into the wall-socket.
Ignite the heater using the
E
Operation panel
F
Handle
G
Removable tank
H
Fuel gauge
key N (refer to Section D).
removable tank
5
If required, change the temperature using the adjustment keys
(refer to Section E).
6
Switch off the heater by pressing the
I
Air filter
J
Vent filter
K
Thermostat
L
Plug + cord
M
Information display
key N.
N
•
The first time you ignite your heater it will smell
key
O
Childproof lock
P
Adjustment keys
like ’new’ for a short time.
•
•
•
Store your fuel in a cool and dark place.
Fuel has a limited shelf life. Start every heating
(time and
season with renewed fuel.
temperature)
The right quality of fuel will be assured, when
you use Zibro Extra or Zibro Kristal for your
Q
Timer
R
SAVE key
heater.
•
If you change to another brand and/or type of
parrafin oil, you must first finish up all the
remaining fuel in the heater.
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
4
43
E
E
E
WHAT YOU NEED TO KNOW IN ADVANCE
ALWAYS MAKE SURE THAT THERE IS SUFFICIENT VENTILATION
For each model the minimum size of space is specified in which you can use the
heater safely, without additional ventilation (refer to Section P). If a particular
room is smaller than the specified space, always put a window or door slightly ajar
(± 2.5 cm). We also recommend doing this in highly insulated or draught-free
rooms and/or at altitudes above 1,500 metres. However, if there is insufficient
ventilation (i.e. oxygen), the heater will automatically switch off. Do not use your
heater in cellars or other underground areas.
THE RIGHT FUEL
Only use Class C1 paraffin fuel in accordance with BS2869; Part 2, or equivalent.
Only the use of the
correct fuel will ensure
safe, efficient, and
comfortable use of your
heater.
Your heater has been designed for use with high-quality water-free pure paraffin
oil, such as Zibro Extra or Zibro Kristal. Only fuels of this kind will ensure clean and
proper burning. Lower quality fuel may result in:
E
increased possibility of malfunctioning
E
incomplete burning
E
reduced heater lifetime
E
smoke and/or smells
E
deposits on the grid or mantle
Using the right fuel is therefore essential for safe, efficient, and comfortable use
of your heater.
Always refer to your local dealer for the right fuel for your heater.
A
This transportation cap
is packed separately in
the box. Only this cap
ensures trouble-free
transportation of the
heater after use.
Store it well!
4
44
MANUAL
A
E
E
E
E
INSTALLING THE HEATER
1 Carefully remove your heater from the box and check the contents.
In addition to the heater you also need to have:
E a transportation cap
E these directions for use
Keep the box and the packaging materials (Fig. A) for storage and/or
transportation.
2 Open the lid of the removable tank D and remove the piece of cardboard.
3 Fill the removable tank as indicated in Section B.
4
The floor should be firm and completely level. Reposition the heater, when it
is not level. Do not try to correct the situation by placing books or other
goods under the heater.
5
Insert the plug L into the wall-socket (230 Volts - AC / 50 Hz) and set the
correct time using the adjustment keys P (refer to Section C).
6 Your heater is now ready for use.
B
FILLING FUEL
Do not fill the removable tank in the living room, but in a more suitable place
(there can always be some spillage). Follow the procedure below:
1 Make sure that the heater is switched off.
B
2 Open the lid 4 and lift the removable tank 7 out of the heater (Fig. B).
Note: Some drops may leak from the tank. Put down the removable tank
(cap pointing upwards) and screw off the fuel cap.
3 Take the manual fuel pump and insert the smooth, most rigid tube into the
jerrycan. Make sure that it is in a higher position than the removable tank
C
(Fig. C). Insert the ribbed hose into the opening of the removable tank.
4 Lock the switch button on top of the pump (turn clockwise).
5 Squeeze the pump a few times, until fuel starts flowing into the removable
tank. As soon as this happens, there is no need to press any longer.
4
45
E
E
6 Check the removable tank fuel gauge H while filling the tank (Fig. D). Stop
D
filling by loosening the switch button on top of the pump (turn anti-clockwise), once the gauge indicates that the tank is full. Never overfill the tank,
especially not when the fuel is very cold (fuel expands when it heats up).
empty
full
7 Let the remaining fuel in the pump flow back into the jerrycan and carefully
remove the pump. Carefully screw the fuel cap back on the tank. Clean off
any spilled fuel.
8 Check whether the fuel cap is straight and tightened properly. Reinstall the
removable tank in the heater (cap down). Close the lid.
C
SETTING THE CLOCK
It is only possible to set the correct time, when the heater is connected to the
mains and not burning. Use the adjustment keys P to set the time. First press
either of the two keys to switch on the function (the 4-digit M will start blinking).
Next, set the hours using the key on the left (
key on the right (
Nhour) and the minutes using the
Mmin.). Press once to increase the value by one step. When you
hold down the key, the value will continue going up, until you release the key
again. After approximately 10 seconds the 4-digit will stop blinking and the
E: When the 4-digit stops
blinking, the setting has
been locked to the
indicated value.
setting will be locked. 5 minutes after switching off the heater, the information on
the display will disappear and the heater will automatically switch into the standby position.
☞
D
When the heater has been unplugged (or after a power failure), the time needs
to be set again.
IGNITING THE HEATER
When used for the first time, a new heater may give out a smell for a short while.
You should therefore provide extra ventilation. Always ignite the heater with the
button N. Never use matches or a cigarette lighter.
Just press the
button N to ignite the heater. The button will start blinking,
indicating that the ignition procedure has started. This will take a short while. Once
the heater is burning, the
button N will remain lit (red). The information display
M will show two numbers. The light next to them indicates that these numbers
refer to the temperatures (Fig. F). The actual room temperature is indicated below
ROOM, while the temperature setting is indicated below SET. The latter can be
F: The required
temperature on the left,
the measured
temperature on the
right.
changed with the adjustment keys (refer to Section E).
Prior to igniting the heater, always check for sufficient fuel in the removable tank.
E
SETTING THE REQUIRED TEMPERATURE
The temperature setting can only be adjusted, when the heater is burning. Use the
adjustment keys P to adjust the temperature. First press either of the two keys to
switch on the function (the °C mark and 4-digit M will start blinking). Next, adjust
the temperature using the key on the right (
higher setting and the key on the left (
Mmin.) to set the temperature to a
Nhour) to lower the temperature. Press
once to increase the value one step. After approximately 10 seconds the °C mark
4
46
and 4-digit will stop blinking and the setting will be locked (Fig. F).
The available temperature settings range from 6°C minimum to 28°C maximum.
When the heater has been unplugged (or after a power failure), the temperature
will reset to the factory setting of 20°C.
F
USING THE TIMER
The timer allows you to switch on the heater automatically at a preset time.
In order to switch on the timer, the correct time must have been set (refer to
Section C) and the heater should be off. Follow the procedure below:
1 Press the
button N and then the TIMER key Q immediately after that.
The TIMER light and the 4-digit M will start blinking.
2 Use the adjustment keys P to set the time at which the heater must ignite.
Use the key on the left (
M
Nhour) to set the hours and the key on the right
( min.) to set the minutes (interval of 5 minutes).
3 After approximately 10 seconds the 4-digit will show CLOCK again and the
TIMER indicator light will light up, indicating that the timer function has been
activated (Fig. G).
4
The timer will ensure that the room will have been heated to approximately
the required temperature at the set time.
☞
G: The TIMER indicator
light indicates that the
timer function has been
switched on.
When you want to switch off the heater and ignite it again with the timer, all
you have to do is press the TIMER key (refer to Section G).
Press the
G
button N once to clear the timer setting.
SWITCHING OFF THE HEATER
There are two ways to switch off the heater.
1 Press the
button N. The information display will show the CLOCK
signal. Within approximately one minute the flame will have extinguished.
2 Press the TIMER key Q, when you want to switch off the heater and ignite it
again with the timer the next time. This not only switches off the heater, but
it also activates the timer function. You can change the required time with
the adjustment keys P (refer to Section F).
H
THE INFORMATION DISPLAY
The information display M not only serves as an indicator of the (set) time and
temperature (sections C, E, and F), it also indicates any malfunctioning of the
heater. The code on the information display tells you what is the matter:
In case of any
malfunctioning the
information display will
tell you what is the
matter.
CODE
INFORMATION
WHAT TO DO
e- 0
f- 0
e- 1
Temperature within the heater too high.
Cool-down and re-ignite.
Power interrupted.
Re-ignite the heater.
Faulty thermostat.
Contact your dealer.
4
47
feeee-
1
2
5
6
7
e- 8
e- 9
Faulty burner thermistor.
Contact your dealer.
Starting problems.
Contact your dealer.
Tipping-over protection.
Re-ignite the heater.
Poor burning.
Contact your dealer.
Room temperature
If necessary,
above 32°C.
re-ignite the heater.
Defective booster.
Contact your dealer.
Air filter dirty; or
Clean filter.
Fuel pump dirty.
Contact your dealer.
The heater has been in operation
continuously for a period of 48 hours
-- : -- +
-- : -- +
and has turned itself off automatically.
Switch the heater back on.
Out of fuel.
Refill removable tank.
Too little ventilation.
Ventilate better.
Always contact your dealer for any malfunctioning not listed above.
AUTOMATIC DEACTIVATION
This heater is fitted with a safety system that ensures that it switches off
automatically after 48 hours continuous operation. The following will then appear
in the display:
the
. If desired, you can switch the heater on again by pressing
button N (see section D).
AUTOMATIC CLEANING MODE
When the heater has been burning continuously for two hours at its highest
setting, the burner will automatically start an autoclean procedure. The display
will show the autocleaningcode cl:05 running back to cl:01. The procedure takes 5
minutes, during which the heater will burn at its lowest setting, while the burner
autocleans. When the burner is clean again, the heater will automatically switch
back to the highest setting again.
I
CHILDPROOF LOCK
The childproof lock can be used to prevent children accidentally changing the
heater settings. When the heater is burning and the childproof lock is on, the heater
can only be switched off. Other functions are blocked then. If the heater has already
been switched off, the childproof lock also prevents accidental ignition of the
heater. Activate the childproof lock by pressing the appropriate key O and holding it
down for more than 3 seconds. The KEY-LOCK indicator (
H: When the
mark
appears, the childproof
lock has been activated.
) will appear on the
information display (Fig. H), indicating that the childproof lock has been activated.
Switch off the childproof lock by pressing the key O and holding it down for more
than 3 seconds once again.
J
THE CORRECT USE OF 'SAVE'
The 'SAVE' function allows you to limit the temperature. When this function is
I: When the SAVE
function is activated, the
heater will automatically
switch on or off in order
to remain within a
specified temperature
range.
4
48
activated, the heater will automatically switch off, when the room temperature
exceeds the set temperature by 3°C. Subsequently, when the room temperature has
dropped again to the set temperature, the heater will automatically switch on again.
Activate the 'SAVE' setting by pressing the appropriate R key.
will display 3
seconds on the information display (Fig. I). Switch off the function by pressing the
SAVE key once again. OFF will display 3 seconds on the information display.
☞
Without the 'SAVE' setting your heater will maintain the set temperature by
approximation as well, by adjusting its heating capacity. 'SAVE' is an economy
setting, which you can use when, for instance, you are not present in the room
or to keep it frost-free.
K
THE 'FUEL' INDICATOR
When the FUEL indicator appears, there is enough fuel left for another 10 minutes
of heater use. The count-down of the remaining heating time can be seen in the
information display M (Fig. J). Every two minutes an alarm signal is sounded,
warning you to refill the removable tank. If you do not react, the heater will
J: When the FUEL
indicator has appeard,
the information display
will show the number of
minutes of fuel left in
the tank.
extinguish by itself. The heater will also sound a warning signal, when it switches
off. The FUEL indicator will blink, while four lines are blinking in the information
display. You can stop this by pressing the
button N once.
Once the heater has used up all its fuel and is extinguished it will take some time,
after the refill, before the heater is completely ready for use again.
L
THE 'VENT' INDICATOR
When the VENT indicator starts blinking, this is a sign that the room is not vented
sufficiently (Fig. K). The heater will switch off automatically. If the indicator
continues blinking after extra ventilation, please contact your dealer.
K: A blinking VENT
indicator is a sign that
you need extra
ventilation.
M
MAINTENANCE
Switch off the heater and let it cool down, before you start any maintenance
work. Also disconnect the plug from the mains. Your heater needs hardly any
maintenance. It is, however, important that you clean the air filter I and the vent
filter J with a vacuum cleaner and the grid 2 with a damp cloth, both on a
L
weekly basis. Remove the air filter occasionally (Fig. L) and clean it with soapy
water. Prior to reinstallation, make sure that the air filter cap has fully been dried.
Regularly inspect the fuel filter as well:
1 Remove the removable tank 7 from the heater and remove the fuel filter
(Fig. M). Some drops may leak from the filter; keep a cloth at hand.
Fuel filter
M
2 Remove the dirt by tapping the fuel filter upside-down against a hard surface.
(Never clean it with water!)
3 Reinstall the fuel filter into the heater.
We recommend that you remove dust and stains from time to time with a damp
cloth, because otherwise these may cause stains that are hard to remove.
☞
Do not remove any heater components yourself. Always contact your dealer for
repairs. When the power cord is damaged, it may only be replaced by an
authorised fitter. Use a new cord of the type H05 VV-F.
4
49
N
STORAGE (END OF THE HEATING SEASON)
At the end of the heating season, you must store the heater in a dust-free place, if
possible in its original packaging. Unused fuel cannot be used in the next heating
season. We therefore recommend that you burn up all fuel. If there is still some
fuel left, do not throw it away, but dispose of it in accordance with the local
regulations for the disposal of domestic chemical waste.
Always start the new heating season with fresh fuel. When you start re-using the
heater follow the instructions again (starting from section A and as specified).
O
TRANSPORTATION
Take the following measures to avoid fuel leakage during the transportation of
the heater:
1 Let the heater cool down.
N
2 Remove the removable tank G from the heater and remove the fuel filter
(refer to Section M, Fig. M). Some drops may leak from the filter; keep a cloth
at hand. Store the fuel filter and the removable tank outside the heater.
3 Place the transportation cap into the position of the fuel filter (Fig. N).
Press it tight.
4 Always move the heater in an upright position.
transportation cap
P
SPECIFICATIONS
Ignition
electrical
Dimensions (mm)
width
374
Fuel
paraffin
(including base plate) depth
280
height
435
Capacity (kW) max.
3.00
Capacity (kW) min.
0.80
Suitable space (m )
40-120
3 **
Accessories
Mains
0.313
Fuel consumption (l/hr)*
250
Fuel consumption (g/hr)*
Burning time per tank (hr)
*
Weight (kg)
230V
-- AC/50 Hz
Electrical consumption
12.8
Capacity removable tank (litres) 4.0
transportation cap
igniter
320 W
continuous 28 W
Fuse rating
250V, 5A
9.5
* At maximum setting ** Specified values are indicative
Q
WARRANTY PROVISIONS
Your heater comes with a 24-month warranty starting on the date of purchase.
Within this period all defects in material or workmanship will be repaired without
any charge. The following provisions shall apply regarding this warranty:
1 We expressly dismiss all other claims for damages, including consequential
damages.
2 Any repairs or replacements of components within the term of warranty will
not result in an extension of the term of warranty.
4
50
3 The warranty shall no longer apply, when the heater has been modified,
non-original parts have been used, or when it is repaired by third parties.
4 The warranty shall not apply to parts that are subject to normal wear, such as
the burner mat and the manual fuel pump.
5 The warranty shall only apply, when you present the original, dated proof of
purchase, provided no changes have been made to it.
6 The warranty shall not apply to damages caused by actions not in compliance
with the Directions for Use, neglect, and the use of an incorrect type of fuel,
or fuel past its use-by date. The use of incorrect fuel can even be dangerous*.
7 Transportation costs and the risks involved during the transportation of the
heater or heater components shall always be at the expense of the purchaser.
In order to avoid unnecessary costs, we recommend that you always read the
’Directions for Use’ carefully first. In case they offer no solution, please take the
heater to your dealer for repair.
* Highly inflammable substances may induce uncontrollable burning, causing flames to break out. Should this
happen, never try to move the heater, but always switch off the heater immediately. In case of emergency you
may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher.
10 TIPS FOR SAFE USE
1
2
150 cm
20 cm
3
50 cm
4
50 cm
150 cm
5
6
7
8
9
10
Make sure that children are always aware of the presence of a burning
heater.
Do not move the heater when it is burning or still hot. Do not refill nor
service the heater when it is burning or still hot.
Position the front of the heater at a distance of minimum 1.5 metres
from walls, curtains, and furniture.
Do not use the heater in dusty rooms or places with strong draughts. In
either situation you will not have optimum burning. Do not use the
heater in the immediate surrounding of a bath, a shower or a
swimmingpool.
Switch off the heater, before you leave or go to sleep. Unplug the
heater as well, when you go away for a longer period of time
(e.g. holidays).
Store and move fuel only in suitable tanks and jerrycans.
Make sure that the fuel is not exposed to heat or extreme temperature
changes. Always store the fuel in a cool, dry and dark place (sunlight
will affect the quality).
Never use the heater in places where harmful gasses or fumes may be
present (e.g. exhaust gasses or paint fumes).
Beware that the grid of the heater becomes hot. If the appliance is
covered there is a risk of fire.
Always make sure that there is sufficient ventilation.
Defective electrical devices and batteries must be kept separate from household
waste. Ensure that there is effective recycling where possible. Ask you local council
or dealer for expert advice on recycling.
4
51
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
G
D
H
E
F
A
J
B
K
I
C
L
M
O
Q
P
P
R
E
N
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
DISTRIBUTED IN EUROPE BY PVG INTERNATIONAL b.v.
i ÖSTERREICH
PVG Austria VertriebsgmbH
Salaberg 49
3350 HAAG
tel:
+43 7434 44867
fax:
+43 7434 44868
email: pvgaustria@zibro.com
4 UNITED KINGDOM
Scott Brothers Ltd.
The Old Barn, Holly House Estate
Cranage, Middlewich, CW10 9LT UK
tel.:
+44 1606 837787
fax:
+44 1606 837757
email: sales@scottmail.co.uk
e BELGIË
PVG Belgium NV/SA
Industrielaan 55
2900 SCHOTEN
tel:
+32 3 326 39 39
fax:
+32 3 326 26 39
email: pvgbelgium@zibro.com
> ITALIA
PVG Italy SRL
Via Niccolò Copernico 5
50051 CASTELFIORENTINO (FI)
+39 571 628 500
tel:
fax:
+39 571 628 504
email: pvgitaly@zibro.com
q SCHWEIZ
PVG Schweiz AG
Salinenstrasse 63
4133 PRATTELN
tel:
+41 61 337 26 51
fax:
+41 61 337 26 78
email: pvgint@zibro.com
u NORGE
Appliance Norge AS
Vogellunden 31
1394 NESBRU
tel:
+47 667 76 200
fax:
+47 667 76 201
email: appliance@appliance-group.com
2 DEUTSCHLAND
PVG Deutschland GmbH
Siemensstrasse 31
47533 KLEVE
tel:
0800 - 9427646
fax:
+31 (0)412 648 385
email: pvgdeutschland@zibro.com
1 NEDERLAND
PVG International B.V.
P.O. Box 96
5340 AB OSS
tel:
+31 412 694 694
fax:
+31 412 622 893
email: pvgnl@zibro.com
6 DANMARK
Appliance A/S
Blovstroed Teglvaerksvej 3
DK-3450 ALLEROED
tel:
+45 70 205 701
fax:
+45 70 208 701
email: appliance@appliance-group.com
9 PORTUGAL
Gardena, Lda
Recta da Granja do Marquês
ALGUEIRÃO
2725-596 MEM MARTINS
tel:
+ 35 21 92 28 530
fax:
+ 35 21 92 28 536
email: pvgint@zibro.com
5 ESPAÑA
PVG España S.A.
Pol. Ind. San José de Valderas II
Comunidad ”La Alameda”
C/ Aurora Boreal, 19
28918 LEGANÉS (Madrid)
tel:
+34 91 611 31 13
fax:
+34 91 612 73 04
email: pvgspain@zibro.com
: POLSKA
PVG Polska Sp. z. o. o.
ul. Kościelna 110
26-800 Białobrzegi
tel:
+48 48 613 00 70
+48 48 613 00 70
fax:
email: pvgpoland@zibro.com
Rev. 8/08
T R TURKEY
PVG Is›tma Klima So¤utma Ltd.fiti.
Tepekule is merkezi
Anadolu Cad. No: 40 K:3 D:306
35010 BAYRAKLI/IZMIR
tel:
+ 90 232 461 51 01
+ 90 232 461 51 85
fax:
email: pvgturkey@zibro.com
man_SRE130TC
y SLOVENIJA
Monteko d.o.o.
Neubergerjeva 4
1000 Ljubljana
+386 (0)1 437 1273
tel:
fax:
+386 (0)1 437 1273
email: info@zibro.si
avg c 080716
F I N SUOMI
Appliance Finland Oy
Piispantilankuja 6C
02240 ESPOO
+358 9 4390 030
tel:
fax:
+358 9 4390 0320
email: appliance@appliance-group.com
= SVERIGE
Appliance Sweden AB
Sjögatan 6
25225 HELSINGBORG
tel:
+46 42 287 830
+46 42 145 890
fax:
email: appliance@appliance-group.com
PVG Traffic
3 FRANCE
PVG France SARL
4, Rue Jean Sibélius
B.P. 185
76410 SOTTEVILLE SOUS LE VAL
+33 2 32 96 07 47
tel:
fax:
+33 0 820 34 64 84
email: pvgfrance@zibro.com
Printed in Japan
7882001921