ENGLISH
This instruction manual is used to describe models listed below.
• Region 1 (DVD Region Code 1 area)/Region 4 (DVD Region Code 4 area)
En este manual de instrucciones se describen los modelos listados a continuación.
• Región 1 (DVD Código de región Área 1)/Región 4 (DVD Código de región Área 4)
Ce mode d’emploi est utilisé pour décrire les modèles de la liste ci-dessous.
• Région 1 (zone de code de région DVD 1)/Région 4 (zone de code de région DVD 4)
For canceling the display demonstration, see page 7.
Para cancelar la demonstración en pantalla, consulte la página 7.
Pour annuler la démonstration des affichages, référez-vous à la page 7.
For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.
For customer Use:
Enter below the Model No. and
Serial No. which are located on
the top or bottom of the cabinet.
Retain this information for future
reference.
Model No.
Serial No.
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
MODE D’EMPLOI
GET0884-001A
[J/JW]
ESPAÑOL
KW-ADV65BT/KW-AV61BT/
KW-AV61
FRANÇAIS
MONITOR WITH DVD RECEIVER
MONITOR CON RECEPTOR DE DVD
MONITEUR AVEC RÉCEPTEUR DVD
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
For KW-ADV65BT/KW-AV61BT Region 1/KW-AV61
WARNINGS: (To prevent accidents and
Region 1:
damage)
• DO NOT install any unit or wire any cable in a location FCC WARNING
This equipment may generate or use radio frequency
where;
energy. Changes or modifications to this equipment may
– it may obstruct the steering wheel and gearshift
cause harmful interference unless the modifications are
lever operations.
expressly approved in the instruction manual. The user
– it may obstruct the operation of safety devices
could lose the authority to operate this equipment if an
such as air bags.
unauthorized change or modification is made.
– it may obstruct visibility.
FCC NOTE
• DO NOT operate the unit while driving.
This equipment has been tested and found to
If you need to operate the unit while driving, be sure
comply with the limits for a Class B digital device,
to look around carefully.
pursuant to Part 15 of the FCC Rules. These limits are
• The driver must not watch the monitor while driving.
designed to provide reasonable protection against
• The driver must not put on the headphones while
harmful interference in a residential installation. This
driving.
equipment may cause harmful interference to radio
CAUTION
communications, if it is not installed and used in
Use of controls or adjustments or performance of
accordance with the instructions. However, there is no
procedures other than those specified herein may result in guarantee that interference will not occur in a particular
hazardous radiation exposure. In compliance with Federal installation. If this equipment does cause harmful
Regulations, following are reproductions of labels on, or
interference to radio or television reception, which can
inside the product relating to laser product safety.
be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference
JVC KENWOOD Corporation
by one or more of the following measures:
2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN
• Reorient or relocate the receiving antenna.
THIS PRODUCT COMPLIES WITH DHHS RULES
• Increase the separation between the equipment and
21CFR SUBCHAPTER J IN EFFECT AT DATE OF
receiver.
MANUFACTURE.
• Connect the equipment into an outlet on a circuit
Location : Top plate
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
For KW-AV61BT Region 4/KW-AV61 Region 4:
technician for help.
The marking of products using lasers
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
2
Cautions on the monitor:
How to reset your unit
ENGLISH
• The monitor built in this unit has been produced with
high precision, but it may have some ineffective dots.
This is inevitable and is not considered defective.
• Do not expose the monitor to direct sunlight.
• Do not operate the touch panel using a ball-point
pen or similar tool with the sharp tip.
Touch the buttons on the touch panel with your
finger directly (if you are wearing a glove, take it off).
• When the temperature is very cold or very hot...
– Chemical changes occur inside, causing malfunction.
– Pictures may not appear clearly or may move
slowly. Pictures may not be synchronized with
the sound or picture quality may decline in such
environments.
• Your preset adjustments will also be erased (except
the registered Bluetooth devices).
How to forcibly eject a disc
Press SRC/
time.
For safety...
and 0 on the monitor panel at the same
+
• Do not raise the volume level too much, as this will
make driving dangerous by blocking outside sounds,
and may cause hearing loss.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit. ( above)
How to read this manual:
• Illustrations of KW-ADV65BT are mainly used for explanation.
• This manual mainly explains operations using the buttons on the monitor panel and touch panel. For
operations using the remote controller (RM-RK256: supplied only for KW-ADV65BT/KW-AV61BT Region 4/
KW-AV61 Region 4), page 62.
• < > indicates the variable screens/menus/operations/settings that appear on the touch panel.
• [ ] indicates the buttons on the touch panel.
• Indication language: English indications are used for the purpose of explanation. You can select the
indication language from the <Settings> menu. ( page 48)
3
ENGLISH
Contents
How to reset your unit ........................................... 3
How to forcibly eject a disc .................................... 3
Listening to the SiriusXM™ Radio for
KW-ADV65BT/KW-AV61BT Region 1/
KW-AV61 Region 1 .........................35
INTRODUCTIONS
Activating subscription........................................ 35
Tuning in to a channel ......................................... 35
Setting the reception restrictions ........................ 37
Detaching/attaching the monitor panel...5
Component names and functions ............6
Initial settings .......................................7
Setting the clock ....................................8
Common operations ...............................9
Sound adjustment ................................39
Using the sound equalization .............................. 39
Adjusting the crossover frequency....................... 40
Turning on the power ........................................... 9
Turning off the power ............................................ 9
Adjusting the volume ........................................... 9
Turning off the screen ........................................... 9
Turning on/off the AV source .............................. 10
Touch screen operation........................................ 10
Changing display design .......................41
Setting for video playback ....................43
Adjusting the picture........................................... 43
Changing the aspect ratio ................................... 44
Zooming the picture ............................................ 44
Using a rear view camera ......................45
Setting menu items ..............................46
Switching screens ................................11
AV SOURCE OPERATIONS
Memorizing/recalling the settings ..................... 49
Updating the system ........................................... 50
Adjusting the touch position .............................. 50
Selecting the playback source ...............12
Listening to the radio ...........................13
Disc operations.....................................17
BLUETOOTH OPERATIONS
Playing a disc....................................................... 17
Playable disc types .............................................. 18
Playback operations ............................................ 19
Settings for disc playback .................................... 23
Information for using Bluetooth®
devices..........................................51
Bluetooth operations for KW-ADV65BT/
KW-AV61BT ...................................51
USB operations.....................................24
Connecting Bluetooth devices ............................. 52
Setting up Bluetooth ........................................... 54
Using the Bluetooth mobile phone...................... 55
Settings for Bluetooth mobile phones ................. 59
Using the Bluetooth audio player ........................ 60
Playing a USB device ........................................... 24
Listening to the iPod/iPhone device ......26
Preparation ......................................................... 26
Setting iPod control mode ................................... 27
Selecting preference settings for iPod/iPhone
playback .............................................................. 27
iPod/iPhone playback operations for <Head>
mode ................................................................... 28
iPod/iPhone playback operations for <iPod Out>
mode ................................................................... 29
Using an App of iPod touch/iPhone ..................... 30
Bluetooth operations for KW-AV61 ........61
Using the Bluetooth mobile phone ..................... 61
Using the Bluetooth audio player ....................... 61
REFERENCE
Using the remote controller ..................62
Operations using the remote controller
(RM-RK256) ........................................................ 62
Pandora® operations for KW-ADV65BT/
KW-AV61BT Region 1/
KW-AV61 Region 1 .........................32
Using other external components..........34
Maintenance .......................................65
More about this unit .............................66
Troubleshooting ...................................69
Specifications.......................................74
Front AUX ............................................................ 34
AV-IN ................................................................... 34
4
Detaching/attaching the monitor panel
Cautions
• Hold the monitor panel securely so as not to drop it accidentally.
• Fit the monitor panel onto the attaching plate until it is firmly locked.
Detaching
Attaching
Turn off the power before detaching the monitor panel.
( page 9)
1
2
5
ENGLISH
INTRODUCTIONS
ENGLISH
Component names and functions
Screen (touch panel)
Monitor panel
1 Loading slot
2 0 (Eject) button
Ejects the disc.
3 HOME/DISP OFF button
• Displays the <HOME> screen. (Press)
( page 12)
• Turns off/on the screen. (Hold) ( page 9)
4 SRC / button
• Turns off the power. (Hold) ( page 9)
• Turns on the power. (Press) ( page 9)
• Selects the AV source. (Press) ( page 12)
5 VOLUME/ATT knob. ( page 9)
• Attenuates the sound. (Press)
• Adjusts the audio volume. (Turn)
6 Remote sensor
7 Reset button
Resets the unit. ( page 3)
8 AUX input jack
9
(Detach) button
Detaches the monitor panel. ( page 5)
Caution on the volume setting:
Digital devices produce very little noise compared
with other sources. Lower the volume before
playing these digital sources to avoid damaging
the speakers by sudden increase of the output
level.
You can change the color of the buttons on the
monitor panel. ( page 41)
6
When you power on the unit for the first time or reset
the unit, the initial setting screen appears.
• You can also change the settings on the <Settings>
screen. ( page 46)
1
Language
Select the text language used
for on-screen information.
( page 48)
• Set <GUI Language>
to display the operation
buttons and menu items
in the selected language
([Local]: initially selected)
or English ([English]).
AV Input
Select an external component
to play. ( page 47)
For KW-ADV65BT/KW-AV61BT
Camera Input Select [On] when connecting
the rear view camera.
( page 48)
Display
Design
For KW-AV61
Select the background
and the colors of the text,
touch panel buttons and
the monitor panel buttons.
( page 41)
Demonstration Activate or deactivate the
display demonstration.
( page 47)
2 Finish the procedure.
The <HOME> screen is displayed.
• [AV Off] is selected initially. Select the playback
source. ( page 12)
7
ENGLISH
Initial settings
ENGLISH
Setting the clock
1 Display the <HOME> screen.
4 Set the clock time.
On the source control screen:
To synchronize the clock time with
FM RBDS
2 Display the <Settings> screen.
To set the clock manually
3 Display the <Time Set> screen.
1 Select the time display format
2 Adjust the hour
3 Adjust the minute
5 Finish the procedure.
8
Turning on the power
Turning off the screen
(Hold)
The screen is turned off.
• You can also turn off the screen on the <HOME>
screen.
Turning off the power
(Hold)
Adjusting the volume
To adjust the volume (00 to 50)
Decrease
Increase
To turn on the screen
• On the source control screen, you can also adjust the
volume by moving your finger on the touch panel
as illustrated. (Not available depending on the AV
source.)
Decrease
or
Touch the screen to display the <HOME> screen.
Increase
To attenuate the sound
The ATT indicator lights up.
To cancel the attenuation, press the VOLUME/ATT
knob.
9
ENGLISH
Common operations
ENGLISH
Turning on/off the AV source
Touch screen operation
You can activate the AV function by selecting source on
<HOME> screen.
A Displays the video control menu while
playing a video.
B Displays the source control
screen while playing a video.
Goes to the previous
chapter/track.*
To turn off the AV source
Goes to the next
chapter/track.*
A Video control menu
The AV source is turned off.
B Source control screen for video playback
• The operation buttons disappear by touching the
screen or when no operation is done for about 10
seconds.
* Not available for video from an external component.
Dragging your finger to left or right functions in the
same way as touching.
10
Source control screen
Common operating buttons
*1
*2*3
TP
Displays the screen of App from the
connected iPod touch/iPhone. ( page 30)
Displays the phone control screen.
( page 56)
Displays the sound adjustment screen.
( page 39)
Activates/deactivates TA standby reception
mode. ( page 16)
• Pressing HOME on the monitor panel also
displays the <HOME> screen.
<HOME> screen
Displays the source control screen/settings screen
and changes the picture source.
page 12
<Settings> screen
Changes the detailed settings. ( page 46)
Displays the phone
control screen *2
Changes the page
*1 Appears when <Input> in <Navigation Input> is
set to [iPhone]. ( page 30)
2
* Only for KW-ADV65BT/KW-AV61BT.
*3 The icon varies depending on the connection status of
the Bluetooth device ( page 51).
Select an item to display on the screen.
AV
Displays the source control
screen. ( above)
Camera
Displays the picture from the rear
view camera. ( page 45)
1
Apps*
Displays the screen of App from
connected iPod touch/iPhone.
( page 30)
Off
Turns off the screen. ( page 9)
• Press [
] to return to the previous screen.
• Press [ ] to display the current source control
screen.
11
ENGLISH
Switching screens
ENGLISH
AV SOURCE OPERATIONS
Selecting the playback source
KW-ADV65BT/KW-AV61BT Region 1
KW-AV61 Region 1
KW-AV61BT Region 4
KW-AV61 Region 4
• Pressing SRC on the monitor panel repeatedly also selects the playback source.
TUNER ( page 13)
Satellite*1 ( page 35)
DISC ( page 17)
USB ( page 24)
iPod ( page 26)
Pandora*1 ( page 32)
Switches to the radio broadcast.
Switches to the SiriusXM™ radio broadcast.
Plays a disc.
Plays files on a USB device.
Plays an iPod/iPhone.
Switches to the Pandora.
Bluetooth*2 (KW-ADV65BT/KW-AV61BT: • KW-ADV65BT/KW-AV61BT: Plays a Bluetooth audio player.
page 60/KW-AV61: page 61)
• KW-AV61: Selects a Bluetooth device.
AV-IN*3 ( page 34)
Apps*4 ( page 30)
Front AUX ( page 34)
AV Off ( page 10)
*1
*2
*3
*4
Switches to an external component connected to LINE IN/VIDEO IN
jacks on the rear panel.
Switches to the screen of App from the connected iPod touch/iPhone.
Switches to an external component connected to AUX input terminal
on the monitor panel.
Turns off the AV source.
Only for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1.
For KW-AV61: Appears only when <AV Input> is set to [BT]. ( page 47)
Appears only when <AV Input> is set to [AV-IN]. ( page 47)
Appears only when <AV Input> is set to [iPod]. ( page 26)
12
Preparation: Select the appropriate tuner channel interval for <Area Setting>. ( page 15)
DX/LO indicator
ST/MO indicator
Standby reception indicator
Preset no.
Band
The station frequency currently
tuned in/PS (station name) for FM
RBDS when PS signal is coming in
PTY code for FM RBDS
Preset list
page 16
• The ST indicator lights up when receiving an FM stereo broadcast with sufficient signal strength.
[P1] – [P6]
[TP]*
[3]
[PTY
]*
• Selects a stored station. (Press)
• Stores the current station. (Hold)
Activates/deactivates TA standby
reception mode. ( page 16)
Displays/hides the information on
the current station ( below).
Enters PTY search mode. ( page 16)
[BAND]
Selects the band.
[4] [¢] Searches for a station.
• Auto search (Press)
• Manual search (Hold)
Selects a stored station.
[ ][ ]
[Mode]
Changes the settings for tuner
reception. ( pages 14 – 15)
[HOME]
Displays the <HOME> screen.
* Appears only when FM is selected as the source.
Displaying the information on the current station
Hides the text
information
Text information (only for
Radio Text Plus)
Scrolls the text information
13
ENGLISH
Listening to the radio
ENGLISH
When an FM stereo broadcast is hard to
receive...
When the FM reception is interfered...
1
Activate monaural mode for better reception.
1
2
2
Auto
On
Off
Activate monaural mode to improve FM
reception, but the stereo effect will be
lost. The MO indicator lights up.
Wide Subject to the interference from
adjacent stations, but sound quality
will not be degraded and the stereo
effect will remain.
Restore the stereo effect.
Tuning in FM stations only with strong
signals—LO/DX (Local/Distance-extreme)
1
2
Local Select this to tune in only to stations
with sufficient signal strength. The LO
indicator lights up.
DX
Increases the tuner selectivity to reduce
interference noises between adjacent
stations. (Stereo effect may be lost.)
Deactivate the function. The DX
indicator lights up.
14
Changing the tuner channel
interval
Storing stations in memory
Tuner channel interval changes depending on the area
you use this unit.
Automatic presetting—SSM (Strongstation Sequential Memory) (For FM only)
1
1
2
2
(Hold)
US
Local stations with the strongest signals are searched
and stored automatically.
Select this when using in North/
Central/South America. FM/AM
intervals are set to 200 kHz/10 kHz.
Manual presetting
1 Tune in to a station you want to preset.
Europe Select this when using in any other
areas. FM/AM intervals are set to 50
kHz/9 kHz.
SA
( page 13)
2 Select a preset number.
Select this when using in South
American countries where FM interval
is 50 kHz. AM interval is set to 10 kHz.
• The initial setting is <US> for KW-ADV65BT/
KW-AV61BT Region 1/KW-AV61 Region 1, and
<SA> for KW-AV61BT Region 4/KW-AV61
Region 4.
(Hold)
The station selected in step 1 is stored.
15
ENGLISH
You can preset six stations for each band.
Activating/deactivating TA Standby
Reception
ENGLISH
Selecting a preset station
TP indicator
Also changes preset stations
The following features are available only for FM
RBDS stations.
Searching for FM RBDS program—
PTY Search
You can search for your favorite programs being
broadcast by selecting the PTY code for your favorite
programs.
1
TP indicator
TA Standby Reception
Lights up
The unit will temporarily switch
to Traffic Announcement (TA) if
available.
Flashes
Not yet activated. Tune in to another
station providing the RBDS signals.
Goes off
Deactivated.
• The volume adjustment for Traffic Announcement
is automatically memorized. The next time the unit
switches to Traffic Announcement, the volume is set
to the previous level.
2 Select a PTY code.
(Hold)
Changes the page
PTY Search starts.
If there is a station broadcasting a program of the
same PTY code as you have selected, that station
is tuned in.
16
Playing a disc
• If a disc does not have any disc menu, all tracks on it will be played repeatedly until you change the source or eject
the disc.
Inserting a disc
Ejecting a disc
Label side
• You can eject a disc when playing another AV source.
• If the ejected disc is not removed within 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust.
• If the disc cannot be ejected, page 3.
The source changes to “DISC” and playback starts.
• The DISC IN (
) indicator lights up while a
disc is inserted.
When removing a disc, pull it horizontally.
Prohibiting disc ejection
Press SRC/
time.
• If “ ” appears on the screen, the unit cannot
accept the operation you have tried to do.
– In some cases, without showing “ ,”
operations will not be accepted.
• When playing back a multi-channel encoded
disc, the multi-channel signals are downmixed
to stereo.
and 0 on the monitor panel at the same
+
To cancel the prohibition, repeat the same procedure
to select [Eject OK?].
17
ENGLISH
Disc operations
ENGLISH
Playable disc types
Disc type
Recording format, file type, etc.
DVD
• DTS sound cannot be
reproduced or emitted from
this unit.
DVD-Video *1
Region Code:
• KW-ADV65BT: 1
• KW-AV61BT/KW-AV61:
1/4 (depending on the
country and sales area)
Playable
DVD-Audio/DVD-ROM
DVD Recordable/Rewritable
(DVD-R/-RW *2, +R/+RW *3)
• DVD Video: UDF bridge
• DVD-VR
• DivX *4/MPEG1/MPEG2/JPEG/
MP3/WMA/WAV: ISO 9660 level
1, level 2, Romeo, Joliet
DVD-Video
DVD-VR *5
DivX *4/MPEG1/MPEG2
JPEG
MP3/WMA/WAV
MPEG4/AAC/DVD+VR/DVD-RAM
Dual Disc
DVD side
Non-DVD side
CD/VCD
Audio CD/CD Text (CD-DA)
VCD (Video CD)
DTS-CD/SVCD (Super Video CD)/CD-ROM/CD-I (CD-I Ready)
CD Recordable/Rewritable
(CD-R/-RW)
• ISO 9660 level 1, level 2,
Romeo, Joliet
CD-DA
VCD (Video CD)
DivX *4/MPEG1/MPEG2
JPEG
MP3/WMA/WAV
MPEG4/AAC
*1 If you insert a DVD Video disc of an incorrect Region Code, “Region Code Error” appears on the screen.
*2 DVD-R recorded in multi-border format is also playable (except for dual layer discs). DVD-RW dual layer discs are not
playable.
3
* It is possible to play back finalized +R/+RW (Video format only) discs. “DVD” is selected as its disc type when a
+R/+RW disc is loaded. +RW double layer discs are not playable.
4
* Playable only for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1.
*5 This unit cannot play back contents protected with CPRM (Content Protection for Recordable Media).
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use
of Non-DVD side of a DualDisc on this product may not be recommended.
18
• When the operation buttons are not displayed on the screen, touch the area shown on
the illustration.
For DVD/DVD-VR/VCD/DivX/MPEG1/MPEG2/JPEG
Audio format Playback mode
( page 22)
Media type
Playing time
DISC IN indicator
Video format/
video playback
mode—VIDEO/
VR-PRG (program)/
VR-PLAY (playlist)/
DivX/MPEG/PBC
[7]*2
[
[
]*3
][
[6]
*1
*2
*3
*4
*5
*6
*7
]*4
Playback status
(3: play / 8: pause / 7: stop)
• DVD Video: Title no./
Chapter no.
• DVD-VR: Program no. (or
Playlist no.)/Chapter no.*1
• DivX/MPEG1/MPEG2:
Folder no./Track no.
• JPEG: Folder no./File no.
• VCD: Track no.
[4] [¢]*5 • Selects a chapter/track.
(Press)
• Reverse/forward search.*6
(Hold)
5 7
Selects title (DVD)/program or
[ ] [ ]* *
playlist (DVD-VR)/folder(DivX/
MPEG1/MPEG2/JPEG). *1
[Mode]*7
Changes the settings for disc
playback. ( page 23)
[HOME]
Displays the <HOME> screen.
Stops playback.
Displays the folder/track list.
( page 20)
Selects playback mode. (
page 22)
Starts/pauses playback.
To display the Original Program/Playlist screen, page 21.
Appears only for DVD/DVD-VR/VCD.
Does not appear for DVD/DVD-VR/VCD.
Does not appear for DVD/DVD-VR/JPEG.
The icon displayed between the buttons varies depending on the type of disc or file.
Search speed varies depending on the type of disc or file.
Does not appear for VCD.
19
ENGLISH
Playback operations
ENGLISH
For CD/MP3/WMA/WAV
Playback mode ( page 22)
Audio format
Playing time
DISC IN indicator
Media type
• MP3/WMA/WAV: Folder
no./Track no.
• CD: Track no.
While playing, the jacket picture is
shown if the file has the tag data
including the jacket picture.
[
[
]*1
][
]
[6]
Playback status
(3: play / 8: pause )
Track/file information
• Touching the information bar scrolls the text if not all of the
text is shown.
[4] [¢]
Displays the folder/track list.
( below)
Selects playback mode.
( page 22)
Starts/pauses playback.
[ ] [ ]*1
[Mode]*1
[HOME]
• Selects a track. (Press)
• Reverse/forward search.*2
(Hold)
Selects a folder.
Changes the settings for disc
playback. ( page 23)
Displays the <HOME> screen.
*1 Does not appear for CD.
*2 Search speed varies depending on the type of disc or file.
Selecting a folder/track on the list
Changes the page
Plays tracks/files in the folder
Playing Recordable/Rewritable discs
• This unit can recognize a total of 5 000 files and
250 folders (a maximum of 999 files per folder).
• Use only “finalized” discs.
• This unit can play back multi-session discs;
however, unclosed sessions will be skipped
while playing.
• Some discs or files may not be played back due
to their characteristics or recording conditions.
Returns to the root folder
Returns to the upper layer
20
[Top Menu] Displays the disc menu (DVD)/original
program (DVD-VR).
Displays the menu/playlist/original
[ ]
program/scene selecting screen.
( below)
Switches to the direct disc menu
[ ]
mode. Touch the target item to select.
• To exit from the menu selecting
screen, press [
].
You can display the video menu screen during video
playback.
• Available items on the screen differ depending on the
types of the loaded disc and playback files.
• The operation buttons disappear by touching the
screen or when no operation is done for about 10
seconds.
• Touching any position other than operation buttons
displays the source control screen.
Using the menu/playlist/original
program/scene selecting screen
[5] [∞]
Selects an item.
[2] [3]
[Enter] Confirms the selection.
[Return] Returns to the menu screen of the
previous layer.
Displays the menu screen of the top
[
]
layer when several menu screens exist
on the disc.
• The screen for MPEG1/MPEG2 differs from the above.
[Zoom]
[Aspect]
[Adjust]
[
]
[ ]
[ ]
[Menu]
• For DivX only
[2] [3] Skips back or forward by about 5
minutes.
[Enter] Confirms the selection.
Exits from the scene selecting screen.
[
]
Displays the picture size selecting
screen. ( page 44)
Selects the aspect ratio. ( page 44)
Displays the picture adjustment
screen. ( page 43)
Selects the audio type.
• For DVD-VR: Selects the audio
channel (ST: stereo, L: left, R: right).
Selects the subtitle type.
Selects the view angle.
Displays the disc menu (DVD)/playlist
(DVD-VR).
• For DVD-VR only
[5] [∞] Selects an item.
[Enter] Confirms the selection.
Displays the menu screen of the top
]
[
layer when several menu screens exist
on the disc.
21
ENGLISH
Video menu operations
ENGLISH
Only for VCD
Selecting playback mode
1
For DVD/DVD-VR
Selects Repeat playback mode
2
For VCD (without PBC)/CD/DivX/MPEG1/MPEG2/MP3/
WMA/WAV
Selects Random
playback mode*
Direct selecting buttons ( below)
[Zoom]
[Aspect]
[Adjust]
[
]
[Return]
[Menu]
[
]
Selects Repeat
playback mode*
* You cannot activate the repeat mode and the random
mode at the same time.
Displays the picture size selecting
screen. ( page 44)
Selects the aspect ratio. ( page 44)
Displays the picture adjustment
screen. ( page 43)
Selects the audio channel (ST: stereo,
L: left, R: right).
Displays the previous screen or the
menu.
Displays the disc menu.
Displays/hides the direct selecting
buttons. ( below)
• Each time you press the button, the playback mode
changes. (The corresponding indicator lights up.)
– Available items differ depending on the types of
loaded disc and playback file.
Indicator
Playback mode
CHAPTER Repeats current chapter.
TITLE
PROGRAM
• To select a track directly
Repeats current title.
Repeats current program (not
available for Playlist playback).
SONGS
Repeats current track.
FOLDER
Repeats all tracks of the current
folder.
FOLDER
Randomly plays all tracks of
current folder, then tracks of next
folders.
ALL
Randomly plays all tracks.
To cancel, press the button repeatedly until the
indicator disappears.
– When you enter a wrong number, press [Direct/
CLR] to delete the last entry.
• To deactivate the PBC function, press [7] then the
direct selecting buttons to select a track number.
22
ENGLISH
Settings for disc playback
Disc Setup items
Selectable setting/item
Initial: Underlined
Menu Language Select the initial disc menu language; Initial English ( page 67).
For DVD/DVD-VR
Audio Language Select the initial audio language; Initial English ( page 67).
Subtitle
Select the initial subtitle language or erase the subtitle (Off).
• Initial for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1: Off, for KWAV61BT Region 4/KW-AV61 Region 4: English ( page 67)
Down Mix
When playing back a multi-channel disc, this setting affects the signals reproduced
through the FRONT OUT/REAR OUT jacks.
z Dolby Surround : Select this to enjoy multi-channel surround audio by
connecting an amplifier compatible with Dolby Surround.
z Stereo
: Normally select this.
For discs except
VCD/CD
Monitor Type
Select the monitor type to watch a wide screen picture on the external monitor.
z 16:9
z 4:3 LB (Letterbox) z 4:3 PS (PanScan)
For discs containing audio/
video/picture files
You can change the dynamic range while playing Dolby Digital software.
D. (Dynamic)
: Select this to enjoy a powerful sound at a low volume
Range Compres. z Off
level with its full dynamic range.
(Compression)
z On
: Select this to reduce the dynamic range a little.
z Dialog
: Select this to reproduce the movie dialog more clearly.
File Type
Select the playback file type when a disc contains different types of files.
: Plays back audio files.
z Audio
: Plays back JPEG files.
z Still Picture
: Plays back DivX/MPEG1/MPEG2 files.
z Video
: Plays back audio files and DivX/MPEG1/MPEG2 files.
z Audio&Video
• For playable file types, page 18.
• If the disc contains no files of the selected type, the existing files are played in the
following priority: audio, video, then still picture.
23
ENGLISH
USB operations
Playing a USB device
• This unit can play JPEG/MPEG1/MPEG2 */MP3/WMA/
WAV files stored in a USB mass storage class device.
• This unit can recognize a total of 5 000 files and 250
folders (a maximum of 999 files per folder).
• Make sure all important data has been backed up to
avoid losing the data.
Cautions:
• This unit may not play back files in a USB device
properly when using a USB extension cable.
• USB devices equipped with special functions such as
data security functions cannot be used with the unit.
• Do not use a USB device with 2 or more partitions.
• Depending on the shape of the USB devices and
connection ports, some USB devices may not be
attached properly or the connection might be loose.
• This unit cannot recognize a USB device whose rating
is other than 5 V and exceeds 1 A.
• This unit may not recognize a memory card inserted
into the USB card reader.
• Connect only one USB device to the unit at a time. Do
not use a USB hub.
• When connecting with a USB cable, use the USB 2.0
cable.
• The maximum number of characters (when the
characters are 1 byte):
– Folder names: 50 characters
– File names: 50 characters
• Avoid using the USB device if it might effect driving
safety.
• Do not pull out and connect the USB device
repeatedly while “Now Reading” is shown on the
screen.
• Electrostatic shock at connecting a USB device may
cause abnormal playback of the device. In this case,
disconnect the USB device then reset this unit and
the USB device.
• Operation and power supply may not work as
intended for some USB devices.
• Do not leave a USB device in the car, or expose
to direct sunlight or high temperature to avoid
deformation or damage to the device.
* Except for MPEG2 files recorded by JVC Everio
camcorder (extension code <.mod>).
Connecting a USB device
You can connect a USB mass storage class device such as
a USB memory, Digital Audio Player etc. to the unit.
USB cable from the
rear of the unit
The source changes to “USB” and playback starts.
• All tracks in the USB device will be played repeatedly
until you change the source.
24
Playback mode ( below)
Audio format
Playing time
Video format—
MPEG/JPEG
• MPEG1/MPEG2/MP3/WMA/
WAV: Folder no./Track no.
• JPEG: Folder no./File no.
Only for MP3/WMA/WAV: While playing, the jacket picture is
shown if the file has the tag data including the jacket picture.
[
]
[
[
]
]
Playback status
(3: play / 8: pause)
Track/file information (for MP3/
WMA/WAV)
• Touching the information bar
scrolls the text if not all of the
text is shown.
] Switches between the internal and
external memory source of the
connected device (such as mobile
phone).
[6]
Starts/pauses playback.
[4] [¢]*3 • Selects a track. (Press)
• Reverse/forward search.*4 (Hold)
Selects a folder.
[ ][ ]
[Mode]
Changes the settings for <File Type>
and <Monitor Type>. ( below)
[HOME]
Displays the <HOME> screen.
Displays the folder/track list. (
page 20)
Selects repeat playback mode. *1 *2
•
SONGS: Repeats the current
track.
FOLDER: Repeats all tracks in
•
the current folder.
Selects random playback mode. *1 *2
•
FOLDER: Randomly plays all
tracks in the folder.
ALL: Randomly plays all tracks.
•
[
• Available items differ depending on the types of playback file.
*1
*2
*3
*4
To cancel random or repeat mode, press the button repeatedly until the indicator disappears.
You cannot activate the repeat mode and the random mode at the same time.
The icon displayed between the buttons varies depending on the file type.
Search speed varies depending on the file type.
Setting <File Type>
Setting <Monitor Type>
Audio
Still Picture
Video
Audio&Video
Select the monitor type to watch a wide screen picture
on the external monitor.
16:9
4:3 LB
4:3 PS
(Letterbox)
(PanScan)
Plays back audio files.
Plays back JPEG files.
Plays back MPEG1/MPEG2 files.
Plays back audio files and MPEG1/
MPEG2 files.
• If the USB device contains no files of the selected
type, the existing files are played in the following
priority: audio, video, then still picture.
25
ENGLISH
• When the operation buttons are not displayed on the screen, touch the area shown on
the illustration.
• To change settings for video playback, page 43.
ENGLISH
Listening to the iPod/iPhone device
• To use App of iPod touch/iPhone (such as MotionX-GPS Drive), page 30.
• To listen to Pandora, page 32.
Preparation
Setting <AV Input> for iPod/iPhone
playback
iPod/iPhone that can be connected to this unit:
Made for
– iPod with video
– iPod classic
– iPod nano (6th Generation)
– iPod nano (5th Generation)
– iPod nano (4th Generation)
– iPod nano (3rd Generation)
– iPod touch (4th Generation)
– iPod touch (3rd Generation)
– iPod touch (2nd Generation)
– iPod touch (1st Generation)
– iPhone 4S
– iPhone 4
– iPhone 3GS
– iPhone 3G
– iPhone
Select an appropriate input setting for <AV Input>
according to the connection method of the iPod/iPhone.
1 Turn off the AV source.
On <HOME> screen:
2 Display the <Input> screen.
Connecting iPod/iPhone
Connect your iPod/iPhone using the appropriate cable
according to your purpose.
• To listen to music: USB 2.0 cable (accessory of the
iPod/iPhone)
To iPod/iPhone
3
USB cable from the
rear of the unit
• To watch video and listen to music: USB
Audio and Video cable for iPod/iPhone—KS-U30
(separately purchased) ( Installation/Connection
Manual)
AV-IN Select this when the iPod/iPhone is
connected using the USB 2.0 cable
(accessory of the iPod/iPhone).
iPod
Caution:
• Video is not displayed on the screen if connected with
any cable other than KS-U30.
26
Select this when the iPod/iPhone is
connected using KS-U30 (separately
purchased).
Select the unit controlling iPod/iPhone playback.
Selecting preference settings
for iPod/iPhone playback
When the source is “iPod”...
When the source is “iPod”...
1
1
2
2
Head
iPod
iPod
Out *
Controls playback from this unit.
( page 28)
Audiobooks Select the speed of audio books.
Controls audio/video playback from
the iPod/iPhone.
• Playback information is shown.
Artwork
Shows/hides the iPod artwork.
• You can change the settings when <iPod
Control> is set to [Head].
Displays the menu and playback
screen output from iPod/iPhone.
( page 29)
• You can control playback from
this unit in the same way as on
the iPod/iPhone.
• When using iPod with video with [iPod] selected
for <iPod Control>, select [iPod] for <AV
Input> and connect iPod using KS-U30 (separately
purchased). ( page 26)
Notice:
* <iPod Out> is available when <AV Input> is set to
[iPod] ( page 26) only for the following iPod/iPhone
models:
– iPod nano (6th Generation)
– iPod touch (4th Generation)
– iPod touch (3rd Generation)
– iPod touch (2nd Generation)
– iPhone 4S
– iPhone 4
– iPhone 3GS
– iPhone 3G
When operating an iPod/iPhone, some operations
may not be performed correctly or as intended. In
this case, visit the following JVC web site: <http://
www3.jvckenwood.com/english/car/> (English
website only)
For some iPod/iPhone models, the performance
may be abnormal or unstable during operation. In
this case, disconnect the iPod/iPhone device, then
check its condition.
If the performance is not improved or slow, reset
your iPod/iPhone.
27
ENGLISH
Setting iPod control mode
ENGLISH
iPod/iPhone playback operations for <Head> mode
• When the operation buttons are not displayed on the screen, touch the area shown on
the illustration.
• To change settings for video playback, page 43.
• Select “iPod” as the source. ( page 12)
• Make sure to select [Head] for <iPod Control>. ( page 27)
• When you turn on this unit, the iPod/iPhone is charged through the unit.
Track no./Total track number/
Playing time
iPod control mode
( page 27)
Playback mode ( below)
Playback status
( 3: play/8: pause)
Song/video information
• Touching the information
bar scrolls the text if not all
of the text is shown.
While playing, Artwork (the picture displayed on the screen of iPod/iPhone) is shown if the song
contains the Artwork ( page 27).
[
]
[
[
]
]
[6]
Starts/pauses playback.
[4] [¢] • Selects an audio/video file. *2
(Press)
• Reverse/forward search. (Hold)
[Mode]
Changes the settings for iPod
playback. ( page 27)
[HOME]
Displays the <HOME> screen.
Displays the audio/video file list.
( page 29)
Selects Repeat playback mode. *1
•
SONGS: Functions the
same as “Repeat One.”
Selects Random playback mode. *1
•
SONGS: Functions the same
as “Shuffle Songs.”
•
ALBUMS: Functions the
same as “Shuffle Albums.”
• To watch the video, select an item on the list of the Video menu. ( page 29)
*1 To cancel random and repeat mode, press the button repeatedly until the indicator disappears.
*2 Resume playback is unavailable for video files.
When you use an App of the connected iPod touch/iPhone, <iPod Control> may be set to [iPod]
unintentionally. To change the setting, page 27.
28
iPod/iPhone playback
operations for <iPod Out>
mode
1
• Connect the iPod/iPhone using KS-U30 (separately
purchased). ( Installation/Connection Manual)
• Select [iPod] for <AV Input>. ( page 26)
• Make sure to select [iPod Out] for <iPod Control>.
( page 27)
• Select “iPod” as the source. ( page 12)
2 Select the menu (audio or video) (1), a
category (2), then a desired item (3).
• Select the item in the selected layer until a
desired file starts playing.
Audio menu:
Switches between audio (
)
(
Selecting a track from the menu on
the iPod/iPhone
) and video
*
[5] [∞]
Selects a category.
[Select/6] Confirms the selection.
[iPod Menu] Returns to the previous layer.
Returns to the top layer Returns to the
previous layer
Plays all items in the layer
Operations during playback
Video menu:
Switches between audio (
(
)
) and video
[2] [3]
Skips to the previous/next track.
[Select/6] Starts/pauses playback.
[iPod Menu] Displays the menu.
• Available categories differ depending on the type of
your iPod/iPhone.
* You can switch to the top of the category by pressing
the corresponding tab: Playlist ( ), Artist ( ),
Albums ( ) or Songs( ).
29
ENGLISH
Selecting an audio/video file from
the menu
ENGLISH
Using an App of iPod touch/iPhone
You can use an App of the connected iPod touch/iPhone on this unit.
• You can operate some functions of an App on the touch panel.
Preparation
• Connect the iPod touch/iPhone using KS-U30 (separately purchased). ( Installation/Connection Manual)
• Select [iPod] for <AV Input>. ( page 26)
• For Apps you can use on this unit, visit <http://mobile.jvc.com>.
1 Start App on your iPod touch/iPhone.
2 Select “Apps” as the source.
• When you use an App of the iPod touch or iPhone,
see also page 31 for safety instructions.
On <HOME> screen:
Displaying the screen of App while
listening to another source
You can switch to the screen of App (such as MotionXGPS Drive) from the connected iPod touch/iPhone while
listening to another source.
You can operate for basic playback on the touch
panel.
Displaying the Apps switch button on the
source control screen and <HOME> screen
Audio
• Select [AV] for <Display> on the <HOME> screen
beforehand. ( page 11)
1 Turn off the AV source.
On <HOME> screen:
2 Display the <Input> screen.
Video
• For some applications such as MotionX-GPS Drive, the
operating buttons and information are not shown.
You can perform the operations on the touch panel,
such as scrolling the map.
• You can also play back the audio/video using iPod/
iPhone itself instead of the unit.
30
3 Select [iPhone] for <Input> on the
To view the screen of App
On <HOME> screen:
ENGLISH
<Navigation Input> screen.
or
On source control screen:
• When <Input> is set to [iPhone], the [Apps]
button is shown on the <HOME> screen, and the
[ ] button is shown on the source control screen.
You can display the screen of App by pressing either
button. ( the right column)
• When <Input> is set to [iPhone], the <AV Input>
setting is automatically changed and fixed to [iPod].
To erase the screen of App
To deactivate, select [Off] for <Input>.
SAFETY INSTRUCTIONS
Use of the iPhone Navigation App is only permitted if the traffic conditions are suitable and you are absolutely
sure that no risk, obstruction or injury will be incurred to you, your passengers or other road users. The
requirements of the Road Traffic Regulations must always be followed and may vary by state. The destination
must not be entered while the vehicle is in motion.
iPhone Navigation guidance may not be applicable to the current situation because of changes in traffic
conditions (e.g. changes in tollroads, principal roads, one-way traffic, or other traffic regulations). In this case,
observe the current traffic signs or regulations.
• Traffic signs should be observed carefully while driving using the iPhone Navigation App. iPhone Navigation
App is only an aid. Driver must always decide whether or not to heed the information provided. We do not
accept liability for erroneous data provided by the iPhone Navigation App.
• Do not operate the unit while driving.
31
ENGLISH
Pandora® operations for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1
Preparation
Install the latest version of the Pandora application on your iPhone/iPod touch/Android/BlackBerry.
• You can operate Pandora using the remote controller. Only playing, pausing, and skipping are available.
Station name/Playing time
Playback status ( 3: play/8: pause)
Track information
• Touching the information
bar scrolls the text if not all
of the text is shown.
The picture data is displayed if available from the current content and when iPhone/iPod touch is connected via USB.
[
]
[Genre]
[ ]
[ ]
[
]
Displays the <Station List>.
( page 33)
Displays the <Genre List>.
( page 33)
Registers the current track as
favorite.
Thumbs down to the current track
and skips to the next track.
Adds the current artist to the
<Station List>.
[
]
[6]
[¢]
[Mode]
[HOME]
Adds the current track to the
<Station List>.
Starts/pauses playback.
Skips the current track.
• Not available when the Pandora
skip reaches its limit.
Displays the connection mode switch
screen. ( below)
Displays the <HOME> screen.
Selecting the connection method for
Pandora
You can stream Pandora from iPhone/IPod touch via a
wired connection or from Android or BlackBerry devices
through Bluetooth.
• For Bluetooth connection, page 52.
• For wired connection, Installation/Connection
Manual.
Wired
Select this to connect iPhone/iPod
touch via USB.
Bluetooth Select this to connect Android/
BlackBerry via Bluetooth.
32
Requirements for Pandora®
iPhone or iPod touch
• Use an Apple iPhone or iPod touch running under
iOS3 or later.
• Install the latest version of the Pandora application
on your iPhone or iPod touch. (Search for “Pandora”
in the Apple iTunes App Store to find and install the
most current version.)
Android™
• Visit the Google play and search for Pandora to
install.
• Bluetooth must be built in and the following profiles
must be supported.
– SPP (Serial Port Profile)
– A2DP (Advanced Audio Distribution Profile)
BlackBerry®
• Visit www.pandora.com from the built in browser to
download the Pandora application.
• Bluetooth must be built in and the following profiles
must be supported.
– SPP (Serial Port Profile)
– A2DP (Advanced Audio Distribution Profile)
NOTE
• Ensure you are logged in to your smartphone
application. If you do not have a Pandora account,
you can create one for free from your smartphone or
at www.pandora.com.
• Pandora is available only in the U.S./Australia/New
Zealand.
• Because Pandora is a third-party service, the
specifications are subject to change without prior
notice. Accordingly, compatibility may be impaired or
some or all of the services may become unavailable.
• Some functions of Pandora cannot be operated from
this unit.
• For issues using the application, contact Pandora at
pandora-support@pandora.com
• Establish an Internet connection by LTE, 3G, EDGE, or
WiFi.
The screen shows the genres sent by the connected
device. Select a genre and station to add to the Station
List.
1 Select a genre.
Changes the page
2 Select a station.
Changes the page
The selected station is added to the Station List.
Selecting a station from the <Station
List>
Appears when Shuffle is activated (All songs in the
registered stations are played randomly)
Appears when the station is shared
Changes the page
To sort the <Station List>
By Date Sorts the list in reverse chronological
order.
A−Z
Sorts the list in alphabetical order.
33
ENGLISH
Adding a station from the <Genre List> to
the <Station list>
ENGLISH
Using other external components
• When the operation buttons are not displayed on the screen, touch the area shown on
the illustration.
• To change settings for video playback, page 43.
AV-IN name* ( below)
Source type (“AV-IN” or
“Front AUX”)
*
[Mode]*
Changes the AV-IN name.
• Press [2] or [3] to select an AV-IN name.
Displays the <HOME> screen.
[HOME]
* Appears when “AV-IN” is selected as the source.
Front AUX
AV-IN
1 Connect an external component.
You can connect external components to the LINE IN/
VIDEO IN jacks. ( Installation/Connection Manual)
Preparation:
Select [AV-IN] for <AV Input>. ( page 47)
• <AV Input> can be changed only when <Input>
in <Navigation Input> is set to [Off].
1 Select “AV-IN” as the source. ( page 12)
2 Turn on the connected component and
3.5 mm stereo mini plug
(not supplied)
start playing the source.
2 Select “Front AUX” as the source.
( page 12)
3 Turn on the connected component and
start playing the source.
34
Before operating, connect the SiriusXM Connect Vehicle Tuner (not supplied) to the expansion port on the rear of the
unit. ( Installation/Connection Manual)
Everything worth listening to is on SiriusXM, getting over 130 channels, including the most commercial-free music,
plus the best sports, news, talk and entertainment. To start listening to the SiriusXM™ Satellite Radio, a SiriusXM
Connect Vehicle Tuner (separately purchased) and subscription are required. For more information, visits www.
siriusxm.com.
Activating subscription
1 Check your Radio ID.
Radio ID is labeled on the casing of the SiriusXM Connect Vehicle Tuner or the bottom of the SiriusXM Connect
Vehicle Tuner unit.
• You can also display the Radio ID on the screen by tuning in to Channel 0.
2 To listen to SiriusXM Satellite Radio, a subscription is required. Activate the SiriusXM
Connect Vehicle Tuner using one of the two methods below:
• Online: Go to www.siriusxm.com/activatenow
• Phone: Call 1-866-635-2349
3 Select “Satellite” as the source. ( page 12)
SiriusXM Connect Vehicle Tuner starts updating all the SiriusXM channels.
Tuning in to a channel
Preset no.
Signal reception indicator
Channel no./Channel name
Band
Category name
Preset list
[P1] – [P6]
• Selects a stored channel. (Press)
• Stores the current channel. (Hold)
[3]
Displays/hides the information on the
current channel. ( page 36)
[
]
[CH Direct]
[BAND]
Selects the band.
[4] [¢]• Selects a channel. (Press)
• Changes the channel rapidly. (Hold)
– While searching, invalid, skipped
and unsubscribed channels are
skipped.
Selects a stored channel.
[ ][ ]
[Mode]
Changes the settings for restrictions.
( page 37)
[HOME]
Displays the <HOME> screen.
Displays the Category/Channel List.
( page 36)
Displays the <Direct Channel
Number> screen. ( page 36)
35
ENGLISH
Listening to the SiriusXM™ Radio for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1
Selecting a preset channel
ENGLISH
Displaying the information on the
current channel
Also changes preset channels
Selecting a channel on the list
1
2 Select a category (1), and then select a
channel (2).
Hides the text information
Current category
Text information
Scrolls the text information
Current channel no./
channel name
Storing channels in memory
You can preset six channels for each band.
1 Tune in to a channel you want to preset.
( page 35)
Changes the page
2 Select a preset number.
Selecting a channel directly
1
2 Enter a channel no. (1), and then
(Hold)
confirm (2).
The channel selected in step 1 is stored.
• To clear the entry, press [Clear].
36
Activating the parental lock
Setting the parental lock
1
You can set the parental lock in order to, for example,
restrict children from receiving adult channels.
On <Mode> screen:
Setting the parental code
• The initial setting is “0000.”
• Changing the code does not change the <P.Lock
Channel Select> and <Skip Channel Select>
settings.
1 Display the <Parental Code> screen.
2 Enter your parental code number (1),
then confirm the entry (2).
2 Enter the current code in <Current
Deletes last entry
Code>, a new code in <New Code>,
and then the new code again for
confirmation the entry in <Confirm
Code>.
3 Select a category (1), and then a
channel you want to activate the
parental lock for (2).
1 Enter a code.
2 Confirm the entry.
The icon appears beside the channel with the
parental lock activated.
Deletes last entry
• To change the parental code, press [Change] on
step 1, enter current code, then new code on step 2
above.
37
ENGLISH
Setting the reception restrictions
ENGLISH
• To cancel the selection, select the locked channel
again in Step 3. The icon disappears and the
selection is canceled.
• When you try to receive a channel with the parental
lock activated, the parental code input screen
appears and you cannot receive the channel until you
enter the correct code.
Skipping unwanted channels
If you do not want to receive some channels, you can
skip them.
Setting the channel skipping
1 Activate the channel skip.
0n <Mode> screen:
Clearing the parental lock for all locked
channel
1
0n <Mode> screen:
2 Select a category (1), and then select a
channel you want to skip (2)
2 Enter your parental code number (1),
and then confirm the entry (2).
Changes the page
The icon appears beside the selected channels.
• Repeat this step if you want to skip more
channels.
Deletes last entry
Clearing the channel skipping for all
skipped channels
0n <Mode> screen:
(Hold)
38
Using the sound equalization
• The adjustment is memorized for each source until you adjust the sound again. If the source is a disc, the
adjustment is stored for each of the following categories.
– DVD/DVD-VR/ VCD
– CD
– DivX/MPEG1/MPEG2/MP3/WMA/WAV
• You cannot adjust the sound when the AV source is turned off.
Selecting a preset sound mode
1
Storing your own adjustment
On <HOME> screen:
Customizing preset sound mode
1 Select a sound mode. ( “Selecting a preset
sound mode”)
2 Adjust the level of each band (1), then
select the subwoofer level (2).
or
On the source control screen:
The adjustments are stored and <User> is
activated.
• To finish the procedure, press [ ].
• To make precise adjustments, page 40.
2 Select a sound mode.
Changes the page
39
ENGLISH
Sound adjustment
ENGLISH
Adjusting the sound precisely
1 Perform steps 1 and 2 of “Selecting a
preset sound mode,” then...
Adjusting the crossover
frequency
1
2 Select a band.
On <HOME> screen:
2
3 Adjust the sound.
3 Select the item to adjust, then make
adjustments.
Adjusts the crossover for front or rear speakers
(high pass filter).
Reset
Freq
Q
Bass
SW Level
Changes level of Low/Mid/
High to 0.
Selects frequency.
Adjusts the width of the
frequency.*1
Activates/deactivates bass.*2
Adjusts subwoofer level.
Adjusts the crossover for subwoofer (low pass filter).
The adjustments are overwritten if the <User>
setting has been made ( page 39), and <User>
is activated.
• The adjustments are memorized until you
adjust sound again.
• To make adjustment for other bands, repeat
steps 2 and 3.
*1 Fixed for “High” band.
*2 Only for “Low” band.
Adjusts the crossover frequency.
Selects the phase for the subwoofer.*
Adjusts the subwoofer level.
* Not selectable when <Freq> is set to <Through>.
40
You can change the background, the color of text, touch panel buttons, and monitor panel buttons.
1
On <HOME> screen:
2 Select/adjust the color
2
Color palette
Dimmer setting: You can make selections for each
dimmer setting—[ ] (Dimmer On) or [ ]
(Dimmer Off).
User color adjuster: You can make your own
color adjustment and store it to <User>.
Text/Buttons
Select/adjust the color. (For details, above.)
3 Select an item ([Backgrnd], [Text] or
[Buttons]), then change the setting.
Variable color illumination*
• Illumination color changes gradually.
Background
1 Select a background
Basic image (default)
* Appears only for button color selecting screen.
When variable color illumination is selected, you
cannot adjust the color.
You can select a color on the color
palette or adjust the color on the user
color adjuster. ( the right column)
For setting your favorite scene as the background,
page 42
41
ENGLISH
Changing display design
5 Capture the image displayed on the
ENGLISH
Using your favorite scene as the
background
screen.
While playing a video or JPEG, you can capture an image
and use the captured image as a background.
• You cannot capture copyrighted content and image
from iPod/iPhone.
• When using a JPEG file as the background, make sure
that the resolution is 800 x 600 pixels.
• The color of the captured image may look different
from that of the actual scene.
1 Play a video or JPEG.
2 Display the <Display Design> screen.
A confirmation message appears. Press [Yes] to
store the newly captured image. (The existing
image is replaced with the new one.)
• Press [No] to return to the previous screen.
( page 41)
3
4 Adjust the image.
[6] *1
[E] *1
[3]
Starts/pauses playback.
Advances scenes frame-by-frame.
Magnifies the scene. (<Full>,
<Zoom1> – <Zoom3>)
[5] [∞]
Moves the zooming frame.
[2] [3] *2
• To cancel the capture, press [
].
*1 Not displayed when playing an external
component connected to LINE IN/VIDEO IN jacks.
2
* Not displayed when <Full> is selected.
42
You can change the setting for video playback.
3 Adjust the picture (–15 to +15).
Adjusting the picture
You can adjust the picture quality.
1 Display the adjustment menu.
Adjusts the brightness
Adjusts the contrast
Adjusts the blackness
Adjusts the color
Adjusts the tint *
Adjusts the detail
* Adjustable only when the incoming signal is
NTSC.
2 Select [ ] (dimmer on) or [ ]
(dimmer off).
43
ENGLISH
Setting for video playback
ENGLISH
Changing the aspect ratio
Zooming the picture
You can change the aspect ratio for video playback.
You can zoom the picture (<Full>, <Zoom1> to
<Zoom3>).
• When <Aspect> is set to <Panorama> or
<Auto> ( the left column), the picture is zoomed
with the aspect ratio of the <Full> setting.
1
1
2
4:3 signal
2
16:9 signal
Full*:
For 16:9 original
pictures
Panorama:
For viewing 4:3
pictures naturally
on the wide screen
[5] [∞] [2] [3]* : Moves the zooming frame.
Regular*:
For 4:3 original
pictures
Auto:
* Not displayed when <Full> is selected.
• The zoom function cannot be used for some video
sources.
• For “DISC”/ “USB”
only: The aspect ratio is
automatically selected
to match the incoming
signals.
* While DivX is played back with <Monitor Type>
set to [16:9] ( page 23), the aspect ratio is not set
correctly.
44
• To use a rear view camera, the REVERSE GEAR SIGNAL lead connection is required. For connecting a rear view
camera, Installation/Connection Manual.
To display the picture from the rear view
camera manually
Activating the rear view camera
1
On <HOME> screen:
On <HOME> screen:
2
To deactivate, select [Off].
When displaying the picture from the rear view
camera manually, you can change the setting of the
picture. ( pages 43 and 44)
Displaying the picture from the rear
view camera
The rear view screen is displayed when you shift the
gear to the reverse (R) position.
To erase the rear view screen
• For KW-ADV65BT/KW-AV61BT Region 1/KW-AV61
Region 1: To erase the caution message, touch the
screen.
45
ENGLISH
Using a rear view camera
ENGLISH
Setting menu items
• When changing settings for <Amplifier Gain>, <AV Input>, and <Input> in <Navigation Input>, turn off
the AV source. Other settings can be changed when the AV source is turned on.
Menu item
Selectable setting/item
Initial: Underlined
Fader : Adjust the front and rear speaker output balance.
z F6 to R6; Initial 0
• When using a two-speaker system, set the fader to the center (0).
Balance : Adjust the left and right speaker output balance.
z L6 to R6; Initial 0
Press [ 5/∞/2/3 ] or drag [ ] to adjust.
• To clear the adjustment, press [Center].
Equalizer
Change the sound mode or adjust and store the equalization for each source.
( page 39)
z Flat/Natural/Dynamic/Vocal Boost/Bass Boost/Vibrant/User
Loudness
You can activate/deactivate loudness.
: Boost low and high frequencies to produce a wellz On
balanced sound at a low volume level.
: Cancels.
z Off
Crossover
Adjust the crossover frequency. ( page 40)
Volume Adjust
Adjust and store the auto-adjustment volume level for each source. (For
discs, the adjustment is stored for each of the following categories: DVD/
DVD-VR/VCD, CD, and DivX/MPEG1/MPEG2/MP3/WMA/WAV.) The volume
level will automatically increase or decrease when you change the source.
z –15 to +6; Initial 0
Amplifier Gain *
z On
z Off
Speaker Select
Select the size of the connected speaker.
z Standard/Narrow/Middle/Wide
Audio
Fader/Balance
: Activates the built-in amplifier.
: Deactivates the built-in amplifier.
* To change the setting, turn off the AV source by pressing [AV Off] on the <HOME> screen beforehand.
46
Dimmer
Selectable setting/item
z Auto
z On
z Off
z Dimmer
Input
Display
Time Set
Initial: Underlined
: Dims the screen and button illumination when you turn on the headlights.
• The ILLUMI lead connection is required. ( Installation/
Connection Manual)
: Activates dimmer.
: Cancels.
: Sets the Dimmer On ( )/Off ( ) times.
• Press [5] or [∞] to set the time.
Display Design
Change the display design (background, the color of text, touch panel buttons, and
monitor panel buttons). ( page 41)
OSD Clock
z On
z Off
Demonstration z On
z Off
: Displays the clock while a video source is played back.
: Cancels.
: Activates the demonstration on the screen.
: Cancels.
Scroll
: Repeats scrolling.
: Scrolls the displayed information once.
: Cancels.
• Touching the information bar scrolls the text regardless of this setting.
GUI Adjust
Adjust the brightness and blackness of the screen.
Press [Enter] to display the setting screen, select [ ] (dimmer on)/[ ] (dimmer off),
then change the following settings:
z Brightness : Adjusts brightness (–15 to +15; Initial 00 for Dimmer On/+15 for
Dimmer Off).
z Black
: Adjusts blackness (–15 to +15; Initial 00).
NTSC/PAL*1
Select the color system of the external monitor.
zNTSC, PAL
AV Input *2*3
You can determine the use of LINE IN/VIDEO IN jacks.
z AV-IN*4
: Select to use the external component connected to LINE IN/VIDEO
IN jacks or the iPod/iPhone connected by using USB 2.0 cable. (
pages 26 and 34)
z iPod
: Select to use the iPod/iPhone connected by using JVC KS-U30. (
page 26)
4 5
z BT* *
: Select when playing back the Bluetooth audio player using the
Bluetooth adapter (KS-BTA100). ( page 61)
z Auto
z Once
z Off
*1 “Please Power Off” appears when the setting is changed. Turn off the power, then turn on to enable the change.
*2 To change the setting, turn off the AV source by pressing [AV Off] on the <HOME> screen beforehand. <AV Input>
can be changed only when <Input> in <Navigation Input> is set to [Off].
3
* The initial setting is [iPod] for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1, and [AV-IN] for KW-AV61BT
Region 4/KW-AV61 Region 4.
4
* When <AV Input> is set to [AV-IN] or [BT], the video from iPod/iPhone is not displayed on the screen.
*5 Only for KW-AV61.
47
ENGLISH
Menu item
Input
Camera Input
System
ENGLISH
Menu item
Selectable setting/item
z On
z Off
Initial: Underlined
: Displays the picture from the rear view camera when
you shift the gear to the reverse (R) position.
: Select this when no camera is connected.
Navigation Input
Change the settings for displaying the screen of App from the connected
iPod touch/iPhone. ( page 30)
• <Navigation Mute> is not used for this unit.
Language
Select the text language used for on-screen information.
z English/Español/Français/Deutsch/Italiano/Nederlands/Svenska/
Dansk/Руccĸий/Português
• “Please Power Off” appears when the setting is changed. Turn off the
power, then turn on to enable the change.
z GUI
: Select a language (<English> or <Local>: the
Language
language selected above) used for displaying operation
buttons and menu items.
Time Set
Adjust the clock time. ( page 8)
Beep
z On
z Off
User Profile
You can memorize, recall, or clear the settings you have made. ( page 49)
Touch Panel Adjust
Adjust the touch position of the buttons on the screen. ( page 50)
Initialize
Initialize all settings you have made. Hold [Enter] to initialize the settings.
• After initializing the settings, adjust the settings on the <Initial
Settings> screen. ( page 7)
Bluetooth Setup*1
Configure settings for using a Bluetooth device, such as connection and
other general operations. ( page 54)
DivX® VOD*2
This unit has its own Registration Code. Once you have played back a
file with the Registration Code recorded, this unit’s Registration Code is
overwritten for copyright protection.
• Press [Enter] to display the information.
• To return to the previous screen, press [OK].
System Information
Displays the version information on the software. You can update the
software. ( page 50)
: Activates the key-touch tone.
: Cancels.
*1 Only for KW-ADV65BT/KW-AV61BT.
*2 Only for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1.
48
You can memorize the following settings:
• Settings on the <Settings> screen: Fader/Balance, Equalizer, Loudness, Crossover (HPF/LPF/SW Level
settings), Volume Adjust, Speaker Select, Dimmer, Display Design, AV Input, Camera Input
• Settings for “AV-IN”: AV-IN Name
Memorizing your settings
Recalling your settings
1
• Turn off the AV source by pressing [AV Off] on the
<HOME> screen beforehand.
On <Settings> screen:
1
On <User Profile> screen ( step 2 on the left
column):
A confirmation message appears. Press [Yes].
2 Finish the procedure.
2
Clearing your settings
1
3 Select an item ([User1], [User2] or
2
[User3]) to memorize the settings.
On <User Profile> screen ( step 2 on the left
column):
Clears all settings memorized in
[User1], [User2] and [ User3]
A confirmation message appears. Press [Yes].
4 Finish the procedure.
A confirmation message appears. Press [Yes].
3 Finish the procedure.
49
ENGLISH
Memorizing/recalling the settings
ENGLISH
Updating the system
Adjusting the touch position
You can update the system by connecting a USB device
containing an update file.
You can adjust the touch position on the touch panel if
the position touched and the operation performed do
not match.
1 Create an update file, copy it to a USB
1
device, and connect it to the unit.
On <Settings> screen:
• To connect a USB device, page 24.
2
On <Settings> screen:
2 Touch the center of the marks at the
lower left and at the upper right as
instructed.
3
APP Version Updates the system application.
DVD Version Updates the DVD system
application.
• To reset the touch position, press [Reset].
• To cancel the current operation, press [Cancel].
It may take a while.
If the update has been completed successfully,
“Update Completed” appears. Reset the unit.
• If the update has failed, turn the power off and then
on, and retry the update.
• Even if you have turned off the power during the
update, you can restart the update after the power
is turned on. The update will be performed from the
beginning.
50
Information for using Bluetooth® devices
• Some Bluetooth devices may not be connected to
this unit depending on the Bluetooth version of the
device.
• This unit may not work for some Bluetooth devices.
• Connecting condition may vary depending on
circumstances around you.
• For some Bluetooth devices, the device is
disconnected when the unit is turned off.
Bluetooth Information: If you wish to
receive more information about Bluetooth, visit
the following JVC web site: <http://www3.
jvckenwood.com/english/car/> (English website
only)
Bluetooth operations for KW-ADV65BT/KW-AV61BT
Bluetooth is a short-range wireless radio communication technology for the mobile device such as mobile phones,
portable PCs, and other devices. The Bluetooth devices can be connected without cables and communicate with each
other.
• Refer to pages i and ii at the end of manual to check the countries where you may use the Bluetooth® function.
Bluetooth profile
Icons for Bluetooth button
This unit supports the following Bluetooth profiles;
• HFP (Hands-Free Profile) 1.5
• OPP (Object Push Profile) 1.1
• A2DP (Advanced Audio Distribution Profile) 1.2
• AVRCP (Audio/Video Remote Control Profile) 1.3
• PBAP (Phone Book Access Profile) 1.0
• SPP (Serial Port Profile)
: No device is connected.
: A Bluetooth audio player is
connected.
: A Bluetooth mobile phone is
connected.
: Both a Bluetooth mobile phone and
audio player are connected.
When shipped from the factory, the Bluetooth
adapter (KS-UBT1) is attached.
• Keep the Bluetooth adapter attached when using
the Bluetooth function.
• This port is designed for the use with KS-UBT1
only. Other Bluetooth adapters or USB devices
cannot be used.
Bluetooth adapter
(KS-UBT1)
51
ENGLISH
BLUETOOTH OPERATIONS
ENGLISH
Connecting Bluetooth devices
Pairing a Bluetooth device using SSP (for
Bluetooth 2.1)
Registering a new Bluetooth device
When you connect a Bluetooth device to the unit
for the first time, make pairing between the unit
and the device. Pairing allows Bluetooth devices to
communicate each other.
• The pairing method differs depending on the
Bluetooth version of the device.
– For the device with Bluetooth 2.1: You can pair
the device and the unit using SSP (Secure Simple
Pairing) which only requires confirmation.
– For the device with Bluetooth 2.0: You need to
enter a PIN code both on the device and unit for
pairing.
• Once the connection is established, it is registered in
the unit even if you reset the unit. Up to 5 devices can
be registered in total.
• Only one device for Bluetooth phone and one for
Bluetooth audio can be connected at a time.
• To use the Bluetooth function, you need to turn on
Bluetooth function of the device.
• To use the registered device, you need to connect the
device to the unit. ( page 53)
When the Bluetooth device is compatible with
Bluetooth 2.1, pairing request is sent from an available
device. Confirm the request both on the device and
the unit.
Rejects the request
Pairing a Bluetooth device using a PIN
code (for Bluetooth 2.0)
1
On <Settings> screen:
The <Bluetooth Setup> screen is displayed.
52
2 Change the PIN code.
• You can skip changing the PIN code.
• The maximum digit of the PIN code that can be
set is 16.
1 Display the <Bluetooth Setup> screen.
( page 52)
2
To connect
Select [Connect] for the target device, and then
select the device you want to connect.
PIN code (initial: 0000)
“Connected” appears. Press [OK] to confirm the
operation.
• All registered devices (mobile phone and audio
player) are listed on <Connect Device>.
– Selectable items depend on the device you
are operating.
Deletes last entry
To disconnect
Select [Disconnect] for the target device.
A confirmation message appears. Press [Yes].
• The Bluetooth connection by <Audio
Connection> is only available when
“Pandora”* or “BT Audio” is selected as the
source.
• The Bluetooth connection by <Pandora
Connection> is only available when
“Pandora” is selected as the source.*
Deleting a registered Bluetooth
device
1
3 Operate the Bluetooth device to
On <Connect Device> screen ( Step 2 above)
2 Select a device to delete.
complete pairing.
When pairing is complete, the device is listed on
<Connect Device>. To use the paired device,
connect the device on <Connect Device>
( the right column).
* Only for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61
Region 1.
A confirmation message appears. Press [Yes].
53
ENGLISH
Connecting/disconnecting a
registered Bluetooth device
ENGLISH
To detach the Bluetooth adapter
• Store the Bluetooth adapter in the supplied bag.
• When inserting the Bluetooth adapter again,
attach it firmly with the JVC logo facing up.
“JVC”
Setting up Bluetooth
To display the <Bluetooth Setup> screen, page 52.
Menu items
Selectable setting/item
Phone Connection
z Connect
z Disconnect
Phone Device
Shows the phone device name.
Audio Connection
z Connect
z Disconnect
Audio Device
Shows the audio device name.
Pandora Connection* z Connect
z Disconnect
Initial: Underlined
: page 53
: page 53
: page 53
: page 53
: page 53
: page 53
Pandora Device*
Shows the Pandora device name.
PIN Code
Changes the PIN code of the unit. ( page 52)
• Touch the current PIN code, enter a new PIN code, then press [Save].
Device Name
Shows the device name to be shown on the Bluetooth device—JVC Unit.
Device Address
Shows the MAC address of the unit.
Auto Connect
z On
z Off
: The connection is automatically established with the last
connected Bluetooth device when the unit is turned on.
: Cancels.
HF/Audio Output
Select the speakers used for Bluetooth (both phone and audio player).
z Front
: From front speakers only.
z All
: From all speakers.
Initialize
Hold [Enter] to clear the registration of Bluetooth devices and memory of the preset list
and call lists.
* Only for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1.
54
Receiving a call
Adjusting the volume of
microphone
When a call comes in...
Status of the device/Battery
reminder (only when the
information comes from the device)
While talking...
Call information
(if acquired)
• This adjustment does not affect the volume level of
the other sources.
• To adjust the volume of calls/earpiece, turn the
volume adjustment knob.
Rejects the call
Switching between handsfree mode
and phone mode
• Phone operation is not available while the picture
from the rear view camera is displayed. ( page 45)
While talking...
When <Auto Answer> is set to [On]
The unit answers the incoming call automatically.
( page 59)
Ending a call
Each time you press the button, the talking method is
switched (
: handsfree mode /
: phone
mode).
While talking...
Notifying SMS reception
If the mobile phone is compatible with SMS (Short
Message Service), the unit tells you a message has been
received. ( page 59)
To read a received message, operate the mobile
phone after stopping the car in a safe place.
• You cannot read, edit, or send a message through
the unit.
• For some mobile phones, the notification message
may not be shown even if the SMS function is
supported.
55
ENGLISH
Using the Bluetooth mobile phone
Direct number entry
ENGLISH
Making a call
1
Deletes last entry
On the source control screen:
Hold: Adds “+”
Presets the entered phone number on
the preset list ( page 58)
• You can also display the phone control screen by
pressing [ Phone] on the <HOME> screen.
• You can enter up to 32 numbers.
Voice dialing
2 Select a method to make a call.
Direct number entry
( the right column)
• Available only when the connected mobile phone has
the voice recognition system.
Preset list/phone book/call
lists ( page 57)
Speak the name you want to call.
Preset list (For presetting, page 58)
Voice dialing ( the right column)
To cancel, press [Cancel].
To reduce echo/noise while talking
Make sure that the NR/EC (Noise reduction/Echo cancel)
function is activated on the screen while talking.
Select [On] to reduce the noise and cancel the echo
while talking. To adjust the echo volume, press [EC –]/
[EC +].
56
2 Select the initial.
Using the preset list/phone book/call lists
Preset
ENGLISH
1
From preset list
From dialled call list.
From received call list.
Displays the other letters
From missed call list.
3 Select a phone number from the list.
From phone book.
• For copying the phone book,
page 58.
To display the details of an entry
When phone book list screen is displayed, you can
display the details of an entry and select a phone
number if several phone numbers are registered.
2
1 Display the details of the desired entry.
2 Select a phone number to call.
To use the A to Z search on phone book
When phone book list screen is displayed, you can
search by initial.
1
57
Presetting the phone numbers
Copying the phone book
ENGLISH
You can preset up to 6 phone numbers.
1
You can copy the phone book memory of a mobile
phone into the unit (up to 400 entries).
On the source control screen:
1
2 Select an item from phone book/call
On the source control screen:
2
lists.
3 Select a phone number.
(Hold)
4 Select a preset number to store into.
PIN code (initial: 0000)
Numbers of the phone book entries copied
3 Operate the target mobile phone.
• You can also preset a phone number entered on the
direct number entry screen by pressing [Save]. (
page 56)
• Refer to the instruction manual supplied with
your mobile phone.
• To cancel the transfer, press [Finish].
4 Finish the procedure.
The phone book memory is copied from the
mobile phone.
58
About mobile phones compatible with
Phone Book Access Profile (PBAP)
1 Display the preset list/phone book/call
If your mobile phone supports PBAP, you can
display the phone book and call lists on the touch
panel screen when the mobile phone is connected.
• Phone book: up to 5 000 entries
• Dialed calls, received calls, and missed calls: up
to 50 entries each
list you want to delete. ( page 57)
2
To display the phone book/call lists of
the mobile phone or the unit
• You cannot delete data when [Phone] is
selected.
Connected mobile phone
3 Select the item you want to delete.
Deletes all the numbers/names in the selected list
This unit
A confirmation message appears. Press [Yes].
Settings for Bluetooth mobile phones
or
Menu items Selectable setting/item
Auto
Answer
z On
z Off
SMS Notify z On
z Off
Initial: Underlined
: The unit answers the incoming calls automatically.
: The unit does not answer the calls automatically. Answer the calls manually.
: The unit informs you of the arrival of a message by ringing and displaying
“Receiving Message.”
: The unit does not inform you of the arrival of a message.
Ring Mode
z System
z Phone
Ring Tone
Change
When <Ring Mode> is set to <System>, press [Enter], then select the ring tone for received
calls and SMS from <Tone1>, <Tone2>, <Tone3>.
z Call Tone
: Selects the ring tone for phone calls.
z Message Tone : Selects the ring tone for SMS.
: The ring tone set on the unit is used.
: The ring tone set on the mobile phone is used. (This function may not work
depending on the mobile phone.)
59
ENGLISH
Deleting the phone number entries
in the unit
ENGLISH
Using the Bluetooth audio player
• To register a new device, page 52.
• To connect/disconnect a device, page 53.
Status of the device/Battery reminder
(only when the information comes Playback mode *1 ( below)
Track no./Playing time *1
from the device)
Playback status
(3: play / 8: pause) *1
page 51
Tag data (current track title/artist
name/album title) *1
• Touching the information bar
scrolls the text if not all of the
text is shown.
• The operation buttons, indications and information displayed on the screen differ depending on the
connected device.
[8]
[
]
[ ]
[3]
Pauses playback.
Selects Repeat playback mode. *1 *2
Selects Random playback
mode. *1 *2
Starts playback.
[4] [¢] • Selects a track. (Press)
• Reverse/forward search. (Hold)
[HOME]
Displays the <HOME> screen.
*1 Available only for the devices compatible with AVRCP 1.3.
*2 To cancel random and repeat mode, press the button repeatedly until the indicator disappears.
60
For Bluetooth operations, it is required to connect the Bluetooth adapter, KS-BTA100 (separately purchased) to the
LINE IN terminals on the rear of the unit. ( Installation/Connection Manual)
• KS-BTA100 is not available in some countries. Please contact your dealer where you purchased this unit.
• For details, refer also to the instructions supplied with the Bluetooth adapter and the Bluetooth device.
• Operations may be different according to the connected device.
Preparation
1 Register (pair) a Bluetooth device with KS-BTA100.
• Refer to the instructions manual supplied with KS-BTA100.
2 Select [BT] for <AV Input>. ( page 47)
Using the Bluetooth mobile phone
KS-BTA100
(Low)
(High)
(Press)
Microphone
(Hold)
Adjusting the microphone volume
Volume level: High/Normal (initial)/Low
• Receiving a call
When a call comes in...
• Making a call
Making a call to the last connected number from your phone.
• Switching between handsfree and phone
While talking...
• Ends/rejects call
• Voice dialing
Voice dialing is available only when the connected mobile phone
has the voice recognition system.
About microphone volume:
• When you turn off the power of the unit, the volume level changes to Normal.
Using the Bluetooth audio player
1 Select “Bluetooth” as the source. ( page 12)
KS-BTA100
Starts/pauses playback.
• If playback does not start, operate the Bluetooth audio player to
start playback.
• Selects a track. (Press)
• Fast-forwards or reverses the track. (Hold)
61
ENGLISH
Bluetooth operations for KW-AV61
ENGLISH
REFERENCE
Using the remote controller
For KW-AV61BT Region 1/KW-AV61 Region 1: To use the remote controller, purchase RM-RK252P separately.
If the effectiveness of the remote controller
decreases, replace the batteries.
Installing the batteries
R03/LR03/AAA
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the unit.
• DO NOT expose the remote sensor to bright light
(direct sunlight or artificial lighting).
Insert the batteries into the remote controller by
matching the polarity (+ and –) correctly.
The unit is equipped with the steering wheel
remote control function.
• See the Installation/Connection Manual
(separate volume) for connection.
• Operations may differ depending on the types of
the steering wheel remote control.
Caution:
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
Operations using the remote controller (RM-RK256)
Button
Operations
ATT
Attenuates/restores the sound.
DISP
Does not function for this unit.
5/∞
• Tuner/SiriusXM radio *1: Selects
the preset stations.
• Selects a title/item/folder.
Button
/
1/¡
62
Operations
• Tuner:
– Searches for stations
automatically.
– Searches for stations manually.
(Hold)
• SiriusXM radio*1 :
– Selects a channel.
– Selects a channel rapidly. (Hold)
• Selects a track.
• Reverse search/forward search.
(Hold)
• Reverse search/forward search.
• DVD-Video/DVD-VR/VCD: Slow
motion playback (during pause).
– DVD-VR/VCD: Reverse slow
motion does not work.
Operations
VOL +/VOL –
• Adjusts the volume level.
• “2nd VOL” function does not
work for this unit.
SOURCE
Selects the source.
6
Starts/pauses*2 playback.
PHONE /
Answers incoming calls.*2
BAND / 7/
•
•
•
•
0–9
( page 64)
• Enters a number while holding
SHIFT.
• The “SETUP” function does not
work for this unit.
1–6
Enters preset station number while
holding SHIFT.
ASPECT
Changes the aspect ratio.
• To check the current aspect ratio
setting, operate on the touch
panel. ( page 44)
RETURN
Returns to the previous screen.
TOP M
( page 64)
• DVD-Video: Shows the disc
menu.
• DVD-VR: Shows the Original
Program screen.
• VCD: Resumes PBC playback.
MENU
( page 64)
• DVD-Video: Shows the disc
menu.
• DVD-VR: Shows the Playlist
screen.
• VCD: Resumes PBC playback.
% /fi/@ / #
• DVD-Video: Makes selection/
settings.
• DivX*1: Skips back or forward by
about 5 minutes.
Button
Selects the bands.
Stops playback.
Ends the call.
Pauses playback of Bluetooth
audio.*3
Operations
ENT
Confirms selection.
OSD/
Does not function for this unit.
DUAL/
Does not function for this unit.
SHIFT
Functions with other buttons.
DIRECT/CLR
• Enters direct search mode when
pressed with SHIFT button.
( page 64)
• Erases the misentry when
pressed with SHIFT button.
• “SURROUND” function does not
work for this unit.
*1 Only for KW-ADV65BT/KW-AV61BT Region 1/KWAV61 Region 1.
2
* Does not work while listening to Bluetooth audio.
*3 Only for KW-ADV65BT/KW-AV61BT.
63
ENGLISH
Button
ENGLISH
Searching for an item directly
Various disc operations
Tuner frequency
1 Press DIRECT while holding SHIFT to enter the
search mode.
2 Press number buttons while holding SHIFT to enter
a frequency.
• To erase a misentry, press CLR (clear) while
holding SHIFT.
3 Press ENT to confirm the entry.
Using the disc menu
• DVD-Video/DVD-VR
1 For DVD Video, press TOP M or MENU.
For DVD-VR, press...
TOP M: To display Original Program
MENU: To display Playlist
2 Press % / fi/@ / # to select an item you want to
play.
3 Press ENT to confirm the selection.
DVD-Video/DVD-VR/DivX/MPEG1/MPEG2/JPEG/
MP3/WMA/WAV/VCD/CD
1 Press DIRECT while holding SHIFT to enter the
search mode.
• Each time you press DIRECT, the item to search
for changes.
2 Press a number button while holding SHIFT to
select a desired item.
• To erase a misentry, press CLR (clear) while
holding SHIFT.
3 Press ENT to confirm the selection.
• VCD
During PBC playback...
1 Press DIRECT while holding SHIFT to enter the
search mode.
2 Press a number button while holding SHIFT to
select the item you want to play.
3 Press ENT to confirm the selection.
• To return to the previous screen, press RETURN.
To cancel PBC playback
1 Press 7 to stop PBC playback.
2 Press DIRECT while holding SHIFT.
3 Press a number button while holding SHIFT to
select a desired track.
4 Press ENT to confirm the selection.
• To resume PBC, press TOP M or MENU.
64
Caution on cleaning the unit
To keep discs clean
Do not use any
solvent (for
example, thinner,
benzine, etc.),
detergent, or
insecticide. This may damage the monitor or the unit.
Recommended cleaning method:
Gently wipe the panel with a soft, dry cloth.
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with a
soft cloth in a straight line from center to
edge.
• Do not use any solvents (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs.
To play new discs
How to clean the connector
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
Connectors
Frequent detachment
will deteriorate the
connectors.
To minimize this
possibility, periodically
wipe the connectors
with a cotton swab or cloth moistened with alcohol,
being careful not to damage the connectors.
Do not use the following discs:
3 inch disc
Warped disc
Sticker and sticker
residue
Stick-on label
Unusual shape
C-thru Disc (semitransparent disc)
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture evaporates.
How to handle discs
When removing a disc from
Center holder
its case, press down the center
holder of the case and lift the
disc out, holding it by the edges.
• Always hold the disc by the
edges. Do not touch its recording surface.
When storing a disc in its case, gently insert the
disc around the center holder (with the printed surface
facing up).
• Make sure to store discs in their cases after use.
Transparent or semitransparent parts on its
recording area
65
ENGLISH
Maintenance
ENGLISH
More about this unit
Playing MP3/WMA/WAV files
File playback
• This unit can play back files with the extension code
<.mp3>, <.wma>, or <.wav> (regardless of the
letter case—upper/lower).
• This unit can play back the files meeting the
conditions below:
– Bit rate:
MP3/WMA: 32 kbps — 320 kbps
– Sampling frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG2)
48 kHz, 44.1 kHz, 32 kHz, 22.05 kHz (for WMA)
44.1 kHz (for WAV)
• This unit can show ID3 Tag Version
1.0/1.1/2.2/2.3/2.4 (for MP3).
• This unit can also show WAV/WMA Tag.
• This unit can play back files recorded in VBR (variable
bit rate).
• Files recorded in VBR have a discrepancy in elapsed
time indication.
• This unit cannot play back the following files:
– MP3 files encoded with MP3i and MP3 PRO
format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded with lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA files copy-protected with DRM.
• This unit can display the jacket picture meeting the
conditions below:
– Picture size: 32 x 32 to 1 232 x 672 resolution
– Data size: less than 650 KB.
− File type: JPEG
Playing DivX files (for discs only/for KWADV65BT/KW-AV61BT Region 1/KW-AV61
Region 1 only)
• This unit can play back DivX files with the extension
code <.divx>, <.div>, or <.avi> (regardless of the
letter case—upper/lower).
• Audio stream should conform to MP3 or Dolby
Digital.
• The file encoded in the interlaced scanning mode
may not be played back correctly.
• The maximum bit rate for video signals (average) is
4 Mbps.
Playing MPEG1/MPEG2 files
• This unit can play back MPEG1/MPEG2 files with the
extension code <.mpg>, <.mpeg>, or <.mod>.
• The stream format should conform to MPEG system/
program stream.
The file format should be MP@ML (Main Profile at
Main Level)/SP@ML (Simple Profile at Main Level)/
MP@LL (Main Profile at Low Level).
• Audio streams should conform to MPEG1 Audio
Layer-2 or Dolby Digital.
• The maximum bit rate for video signals (average) is
4 Mbps.
Playing JPEG files
• This unit can play back JPEG files with the extension
code <.jpg> or <.jpeg>.
• This unit can play back JPEG files that are at 32 x 32 to
8 192 x 7 680 resolution.
It may take time to display the file depending on its
resolution.
• This unit can play back baseline JPEG files.
Progressive JPEG files or lossless JPEG files cannot be
played.
We bear no responsibility for any loss of data
in an iPod/iPhone and USB mass storage
class device while using this unit.
66
Through the analog terminals (Speaker out/REAR OUT/FRONT OUT )
2-channel signal is emitted. When playing multi-channel encoded disc, multi-channel signals are downmixed.
Language codes (for DVD/DVD-VR language selection)
Code
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
Language
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scots Gaelic
Code
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JA
JI
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
LV
MG
Language
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Code
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
QU
RM
RN
RO
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
67
Language
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Code
SO
SQ
SR
SS
ST
SU
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Language
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
ENGLISH
Sound signals emitted through the rear terminals
ENGLISH
• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
• “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other
countries.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically
to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, or iPhone may affect wireless performance. iPhone, iPod, iPod
classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
• This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property
rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
• Font for this product is designed by Ricoh.
Only for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1
• DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used
under license.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is
an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to
convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX
Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device
setup menu. Go to vod.divx.com for more information on how to complete your registration.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora
Media, Inc., used with permission.
• Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.
• Android is a trademark of Google Inc.
• BlackBerry®, RIM®, Research In Motion® and related trademarks, names and logos are the property of Research
In Motion Limited and are registered and/or used in the U.S. and countries around the world. Used under license
from Research In Motion Limited.
Only for KW-ADV65BT/KW-AV61BT
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective
owners.
68
What appears to be trouble is not always serious. Check the following points before calling a service center.
• For operations with the external components, refer also to the instructions supplied with the adapters used for the
connections (as well as the instructions supplied with the external components).
If the following messages appear
Message
“No Signal”
“MISWIRING Check wiring
connection then reset unit”
“WARNING Check wiring
connection then reset unit”
“Parking Brake”
“Eject Error” / “Loading Error”
“Restricted Device”
“USB Device Error”
“No BT Dongle”*1
“Connection Error”*1
“Please Wait...”*1
“No Voice Device”*1
“No Data”*1
“Initialize Error”*1
“Dial Error”*1
“Hung Up Error”*1
“Pick Up Error”*1
“Pairing Error”*1
“Pandora upgrade required”*2
Remedy/Cause
• Start the playback on the external component connected to VIDEO IN jack.
• Check the cords and connections.
• Signal input is too weak.
A speaker cord has shorted or it has come in to contact with the car chassis.
Wire or insulate the speaker cord as appropriate, then reset the unit
( page 3). See also the Installation/Connection Manual.
No playback picture is shown when the parking brake is not engaged.
Eject the disc forcibly. ( page 3)
Check whether the connected iPod/iPhone is compatible with this unit. (
page 26)
• The USB power voltage is abnormal.
• Turn off and turn on the unit.
• Connect another USB device.
The Bluetooth adapter (KS-UBT1) is removed.
The device is registered but the connection has failed. Connect the registered
device. ( page 53)
The unit is preparing to use the Bluetooth function. If the message does not
disappear, turn off and turn on the unit, then connect the device again (or reset
the unit).
The connected mobile phone does not have the voice recognition system.
No phone book data is contained in the connected Bluetooth phone.
The unit has failed to initialize the Bluetooth module. Try the operation again.
Dialing has failed. Try the operation again.
The call has not ended yet. Park your car, and use the connected mobile phone
to end the call.
The unit has failed to receive a call.
Pairing between the unit and Bluetooth device has failed. Register the device
again. ( page 52)
The Pandora application on your iPhone/iPod touch/Android/BlackBerry is not
the latest version. Update the application.
*1 Only for KW-ADV65BT/KW-AV61BT.
*2 Only for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1.
69
ENGLISH
Troubleshooting
If there seems to be a problem
General
ENGLISH
Symptom
Remedy/Cause
No sound comes out of the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
No picture is displayed on the screen.
Turn on the screen. ( page 9)
The unit does not work at all.
Reset the unit. ( page 3)
The remote controller*1 does not work.
Replace the battery.
The desired source button ([Bluetooth]*2,
[AV-IN], or [Apps]) is not displayed on the
<HOME> screen.
Select an appropriate setting for <AV Input>. ( page
47)
DivX/MPEG1/MPEG2/
JPEG/MP3/WMA/WAV
Disc in general
TUNER
The Apps switch button ([ ]) on the source Select an appropriate setting for <Navigation Input>.
( page 48)
control screen or [Apps] button on the
<HOME> screen is not displayed.
SSM automatic presetting does not work.
Store stations manually. ( page 15)
Static noise while listening to the radio.
Connect the antenna firmly.
Disc can be neither recognized nor played
back.
Eject the disc forcibly. ( page 3)
Disc cannot be ejected.
Unlock the disc. ( page 17)
• Insert a finalized disc.
• Recordable/Rewritable discs cannot be
• Finalize the discs with the component which you used
played back.
for recording.
• Tracks on the Recordable/Rewritable discs
cannot be skipped.
Playback does not start.
The format of files is not supported by the unit.
No picture appears on the external monitor.
• Connect the video cord correctly.
• Select the correct input on the external monitor.
Disc cannot be played back.
• Record the tracks using a compliant application on the
appropriate discs. ( page 18)
• Add appropriate extension codes to the file names.
Tracks are not played back as you have
intended them to play.
Playback order may differ from the one played back using
other players.
*1 For KW-AV61BT Region 1/KW-AV61 Region 1: Purchase RM-RK252P separately.
*2 Only for KW-AV61.
70
While playing a track, sound is sometimes
interrupted.
The tracks are not properly copied into the USB device.
Copy tracks again, and try again.
No sound comes out of the speakers.
• Disconnect the iPod, then connect it again.
• Select another source, then reselect “iPod”.
The iPod/iPhone does not turn on or does
not work.
•
•
•
•
Sound is distorted.
Deactivate the equalizer either on this unit or the iPod/
iPhone.
A lot of noise is generated.
Turn off (uncheck) “VoiceOver” of the iPod. For details, visit
<http://www.apple.com>.
No operations are available when playing
back a track containing Artwork.
Operate the unit after the Artwork is loaded.
Sound does not synchronize with the video.
Select [iPod] for <AV Input>. ( page 47)
• Videos cannot be played.
• No sound of videos come out.
• Connect with USB Audio and Video cable JVC KS-U30.
Other cables cannot be used.
• Select [iPod] for <AV Input>. ( page 47)
No picture appears on the screen.
• Turn on the video component if it is not on.
• Connect the video component correctly.
The Pandora application does not work.
The Pandora application on your iPhone/iPod touch/
Android/BlackBerry is not the latest version. Update the
application.
iPod/iPhone
Check the connecting cable and its connection.
Update the firmware version.
Charge the battery.
Check whether the iPod control mode is correctly
selected. ( page 27)
• Reset the iPod/iPhone.
71
ENGLISH
Turn off the power and on again.
USB
“Now Reading...” does not disappear from
the screen.
AV-IN
Remedy/Cause
Pandora
Symptom
SiriusXM™ radio (only for KW-ADV65BT/KW-AV61BT Region 1/KW-AV61 Region 1)
ENGLISH
Symptom
Remedy/Cause
“No Signal” appears on the screen.
Make sure the SiriusXM radio antenna is mounted outside
the vehicle. Move vehicle to an area with a clear view of
the sky.
“Check Antenna” appears on the screen.
• Check the SiriusXM radio antenna connection, and make
sure the antenna is firmly attached to the tuner.
• Check whether the SiriusXM radio antenna cable is bent
or broken. If it is damaged, replace the whole antenna
unit.
“Check Tuner” appears on the screen.
Make sure the SiriusXM tuner is connected to the unit.
“Chan Unavailable” appears on the screen
for about 2 seconds, then returns to the
previous channel.
Selected channel is no longer available or is unauthorized.
Select another channel or continue listening to the
previous channel.
"Ch Unsubscribed" appears on the screen.
Selected channel is not part of your current subscription
plan. Call 1-866-635-2349 to subscribe.
“Subscription Updated – Press Enter to
Continue” appears on the screen.
Your subscription is updated. Press the appropriate button
to continue.
“Channel Locked” appears on the screen.
The selected channel has been locked by the parental
controls. Enter unlock code after you are asked. ( page 38)
“Incorrect Lock Code” appears on the screen. The selected channel is a mature or parental lock channel,
and locked by parental lock or user lock code. Enter the
correct lock code.
72
Bluetooth (only for KW-ADV65BT/KW-AV61BT)
Remedy/Cause
Phone sound quality is poor.
• Reduce the distance between the unit and the
Bluetooth mobile phone.
• Move the car to place where you can get a better signal
reception.
The sound is interrupted or skipped while
using a Bluetooth audio player.
• Reduce the distance between the unit and the
Bluetooth audio player.
• Disconnect the device connected for Bluetooth phone.
• Turn off, then turn on the unit.
• (When the sound is not yet restored) connect the player
again.
The connected audio player cannot be
controlled.
Check whether the connected audio player supports AVRCP
(Audio Video Remote Control Profile).
Bluetooth device does not detect the unit.
• Check whether the Bluetooth adapter (KS-UBT1) is
inserted correctly.
• Search from the Bluetooth device again.
The unit does not make pairing with the
Bluetooth device.
• For devices compatible with Bluetooth 2.1: Register the
device using a PIN code. ( page 52)
• For devices compatible with Bluetooth 2.0: Enter the
same PIN code for both the unit and target device.
If the PIN code of the device is not indicated on its
instructions, try “0000” or “1234.”
Echo or noise occurs.
• Adjust the microphone unit position.
• Make sure that the NR/EC (Noise reduction/Echo cancel)
function is activated. Adjust the echo level if necessary
( page 56)
The unit does not respond when you try to
copy the phone book to the unit.
You may have tried to copy the same entries (as stored)
to the unit.
73
ENGLISH
Symptom
AMPLIFIER
ENGLISH
Specifications
Power Output
20 W RMS × 4 Channels at 4 Ω and ≤ 1% THD+N
Signal-to-Noise Ratio
80 dBA (reference: 1 W into 4 Ω)
Load Impedance
4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control Range
Frequencies
Audio Output Level
LINE OUT (FRONT/REAR),
SUBWOOFER
Other Terminals
FM/AM TUNER
Frequency Range
FM Tuner
DVD/CD
AM Tuner
Signal Detection System
Frequency Response
Dynamic Range
Signal-to-Noise Ratio
Wow and Flutter
Color System
Video-Out (composite)
Level
Low: 60 Hz, 80 Hz, 100 Hz, 150 Hz
Mid: 500 Hz, 1 kHz, 1.5 kHz, 2 kHz
High: 10 kHz, 12.5 kHz, 15 kHz, 17.5 kHz
±10 dB
Line-Out Level/Impedance
4 V/20 kΩ load (full scale)
Output Impedance
1 kΩ
Input
LINE IN, VIDEO IN, CAMERA IN, USB input, MIC
IN*1, AUX, Antenna input
Expansion port (SXi*2), OE REMOTE
87.9 MHz to 107.9 MHz
Others
FM with channel interval set
to 200 kHz
with channel interval set 87.5 MHz to 108.0 MHz
to 50 kHz
AM
530 kHz to 1 700 kHz
Usable Sensitivity
9.3 dBf (0.8 μV/75 Ω)
50 dB Quieting Sensitivity
16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity
65 dB
(400 kHz)
Frequency Response
40 Hz to 15 000 Hz
Stereo Separation
40 dB
Sensitivity/Selectivity
20 μV/40 dB
Non-contact optical pickup (semiconductor laser)
DVD, fs=48 kHz/96 kHz
16 Hz to 22 000 Hz
VCD/CD
16 Hz to 20 000 Hz
93 dB
95 dB
Less than measurable limit
NTSC/PAL
1 Vp-p/75 Ω
*1 Only for KW-ADV65BT/KW-AV61BT.
*2 Only for Region 1 models.
74
GENERAL
MONITOR
BLUETOOTH*
Compatible Device
Compatible File System
Max. Current
USB 2.0 Full Speed
Full Speed
Low Speed
Mass storage class
FAT 32/16/12
DC 5 V 1 A
Version
Bluetooth 2.1+EDR certified
Output Power
+4 dBm Max. (Power class 2)
Service Area
Within 10 m (10.9 yd)
Profile
HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1
A2DP (Advanced Audio Distribution Profile) 1.2
AVRCP (Audio/Video Remote Control Profile) 1.3
PBAP (Phone Book Access Profile) 1.0
SPP (Serial Port Profile)
Screen Size
6.1 inch wide liquid crystal display
Maximum 12 Mbps
Maximum 1.5 Mbps
Number of Pixel
1 152 000 pixels: 800 (horizontal) × 3 (RGB) × 480 (vertical)
Drive Method
TFT (Thin Film Transistor) active matrix format
Color System
NTSC/PAL
Aspect Ratio
16:9 (wide)
Power Requirement
Operating Voltage
DC 14.4 V (11 V to 16 V allowance)
Grounding System
Negative ground
Allowable Storage Temperature
–10°C to +60°C (14°F to 140°F)
Allowable Operating Temperature
0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D) Installation Size (approx.)
182 mm × 111 mm × 160 mm
(7-3/16” ×4-3/8” × 6-5/16”)
Panel Size (approx.)
188 mm × 117 mm × 10 mm
(7-7/16” × 4-5/8” × 7/16”)
Mass (approx.)
2.3 kg (5.1 lbs) (including the Trim plate and
Mounting sleeve)
* Only for KW-ADV65BT/KW-AV61BT.
Design and specifications are subject to change without notice.
If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality shop.
75
ENGLISH
USB
USB Standards
Data Transfer Rate
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
The countries where you may use the
Bluetooth® function (For KS-UBT1)
Die Länder, in denen Sie die Bluetooth® Funktion verwenden können
Pays où vous pouvez utiliser la fonction Bluetooth®
De landen waar u de Bluetooth®-functie mag gebruiken
Países en los que se puede utilizar la función Bluetooth®
Paesi nei quali è possibile utilizzare la funzione Bluetooth®
Länder där du kan använda Bluetooth®-funktionen
Lande, hvor du kan bruge Bluetooth®-funktionen
Land hvor du kan bruke Bluetooth®-funksjonen
Maat, joissa voi käyttää Bluetooth®-toimintoa
Países onde pode usar a função Bluetooth®
Países onde você pode usar a função Bluetooth®
Οι χώρες όπου μπορείτε να χρησιμοποιήσετε τη λειτουργία Bluetooth®
Страны, где можно воспользоваться функцией Bluetooth®
Země, ve kterých můžete využívat funkci Bluetooth®
Azok az országok, amelyekben használhatjuk a Bluetooth®-funkciót
Kraje, w których można używać funkcji Bluetooth®
Države, kjer lahko uporabljate funkcijo Bluetooth®
Krajiny, v ktorých môžete využívať funkciu Bluetooth®
Valstis, kur jūs varat izmantot Bluetooth® funkciju
Šalys, kuriose galite naudotis „Bluetooth®“ funkcija
Il-pajjiżi fejn tista’ tuża l-funzjoni Bluetooth®
Lönd þar sem hægt er að nota Bluetooth®
Riigid, kus on võimalik kasutada Bluetooth® funktsiooni
Bluetooth® fonksiyonunu kullanabileceğiniz ülkeler
7
7
7
Na tíortha inar féidir leat feidhmiú Bluetooth® a úsáid
Länner an denen der d’Bluetooth® Funktioun benotze kënnt.
7
ͪ nhͻng qu͝c gia mà b̭n có th͏ s͹ dͱng ch͵c nćng Bluetooth®
7
Els països on podrà fer servir la funció Bluetooth®
Zemlje u kojima je dozvoljena upotreba Bluetooth® funkcije.
Zemlje u kojima možete koristiti Bluetooth® funkciju
Zemlje u kojima je dopušteno koristiti Bluetooth®.
Земји каде можете да ја користите функцијата Bluetooth®
Страните, в които можете да ползвате функцията Bluetooth®
Ţările în care puteţi utiliza funcţia Bluetooth®
Die lande waar u die Bluetooth®-funksie kan gebruik
Amazwe lapho ungasebenzisa khona uhlelo lwe-Bluetooth®
Ang mga bansa kung saan maaari kang gumamit ng Bluetooth® function
Negara-negara yang memperbolehkan penggunaan fungsi Bluetooth®
Negara-negara yang anda boleh menggunakan fungsi Bluetooth®
ȯ ‘ȯ ž ‡¡ȡȱ ]” %OXHWRRWKp €ȡ™[-¢˜ȡ €ȡ `”™Ȫ‚ €š €ȯ ¡ɇ
您能够使用 Bluetooth® 功能的国家
您能夠使用 Bluetooth® 功能的國家
Bluetooth® 기능을 사용할 수 있는 국가
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
i
Country
Andorra
Australia
Österreich
Bosna i Hercegovina
Belgien
Belgique
България
Brasil
Canada
Schweiz
Suisse
Chile
Κύπρος
Kıbrıs
Česká republika
Deutschland
Danmark
Eesti
España
Suomi
Finland
France
United Kingdom
Ελλάδα
Hong Kong
香港
香港
Hrvatska
Magyarország
Indonesia
Country
Country
Ireland
Sverige
Éire‘ȯ ž ‡¡ȡȱ ]” %OXHWRRWKp €ȡ™[
Singapore
ȯ
-¢˜ȡ €ȡ `”™Ȫ‚ €š €ȯ ¡ɇ
India
新加坡
—ȡš
Singapura
Ísland
Slovenija
Slovensko
Italia
대한민국
Lichtenstein
Türkiye
Lietuva
台湾
Luxemburg
United States of America
Luxembourg
Venezuela
Lëtzebuerg
Vietnam
Latvija
Vi͓t Nam
Monaco
South Africa
Crna Gora
ENingizimu Afrika
Македонија
Suid-Afrika
Malta
Malaysia
Nederland
Norge
New Zealand
Perú
Philippines
Pilipinas
Polska
Portugal
República Oriental del
Uruguay
România
Srbija
Россия
11-1672-007
ii
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Still having trouble??
USA ONLY
Call 1-800-252-5722
http://www.jvc.com
We can help you!
EN, SP, FR
© 2012 JVC KENWOOD Corporation
1112EHHMDWJEIN
KW-ADV65BT/KW-AV61BT/KW-AV61
Installation/Connection Manual
Manual de instalación/conexión
Manuel d’installation/raccordement
GET0884-003A
[J/JW]
1112EHHMDWJEIN
EN, SP, FR
© 2012 JVC KENWOOD Corporation
ENGLISH
ESPAÑOL
This installation/connection manual is used to describe models
listed below.
• Region 1 (DVD Region Code 1 area)
• Region 4 (DVD Region Code 4 area)
FRANÇAIS
Este manual de instalación/conexión proporciona instrucciones
para los modelos indicados a continuación.
• Región 1 (Área del Código de Región 1 de DVD)
• Región 4 (Área del Código de Región 4 de DVD)
Ce manuel d'installation/connexion est utilisé pour décrire les
modèles de la liste ci-dessous.
• Région 1 (DVD, code de région 1)
• Région 4 (DVD, code de région 4)
This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems. If your vehicle does not have this system, a
voltage inverter is required, which can be purchased at JVC car audio
dealers.
Esta unidad está diseñada para funcionar con 12 V de CC, con
sistemas eléctricos de masa NEGATIVA. Si su vehículo no posee
este sistema, será necesario un inversor de tensión, que puede ser
adquirido en los concesionarios de JVC de equipos de audio para
automóviles.
Cet appareil est conçu pour fonctionner sur des sources de courant
continu de 12 V à masse NEGATIVE. Si votre véhicule n’offre pas ce
type d’alimentation, il vous faut un convertisseur de tension, que vous
pouvez acheter chez un revendeur d’autoradios JVC.
WARNINGS
ADVERTENCIAS
AVERTISSEMENTS
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations,
as this may result in a traffic accident.
– it may obstruct the operation of safety devices such as air bags, as
this may result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as
this may result in a traffic accident.
• The driver must not watch the monitor while driving. It may lead to
carelessness and cause an accident.
• If you need to operate the unit while driving, be sure to look around
carefully or you may be involved in a traffic accident.
• If the parking brake is not engaged, “Parking Brake” appears on the
monitor, and no playback picture will be shown.
• NO instale ningún receptor o tienda ningún cable en una
ubicación donde;
– donde pueda obstruir la maniobra del volante de dirección
y del cambio de engranajes, con el consiguiente riesgo de
accidentes de tráfico.
– donde pueda obstruir el funcionamiento de dispositivos de
seguridad tales como bolsas de aire, pues podría resultar en un
accidente fatal.
– donde pueda obstruir la visibilidad.
• NO opere la unidad mientras está maniobrando el volante de
dirección, pues podría producirse un accidente de tráfico.
• El conductor no debe mirar el monitor mientras conduce. Podría
producirse un descuido, y causar un accidente.
• Si necesita operar la unidad mientras conduce, asegúrese de
mirar atentamente a su alrededor pues de lo contrario, se podría
producir un accidente de tráfico.
• Si el freno de mano no está en uso, aparecerá “Parking Brake
(Freno de Mano)” en la pantalla y no se mostrará ninguna
secuencia de imagen.
• N’INSTALLEZ aucun appareil ni aucun câble dans un endroit où:
– où il peut gêner l’accès au volant ou au levier de vitesse car cela
peut entraîner un accident de la circulation.
– où il peut gêner la manipulation de dispositifs de sécurité tels que
les airbags car cela peut entraîner un accident fatal.
– où il peut gêner la visibilité.
• NE COMMANDEZ PAS l’appareil lors de la manipulation du volant
car cela peut entraîner un accident de la circulation.
• Le conducteur ne doit pas regarder le moniteur lorsqu’il conduit. Cela
peut lui faire perdre sa concentration et causer un accident.
• Si vous souhaitez opérer l’appareil pendant que vous conduisez,
assurez-vous de bien regarder autour de vous afin de ne pas causer un
accident de la circulation.
• Si le frein à main n’est pas engagé, “Parking Brake (Frein à Main)”
s’affiche sur le moniteur et aucune image de lecture n’apparaît.
To prevent short circuits, disconnect the battery’s negative terminal
and make all electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after
installation.
• Be sure any cable is not caught on the car’s chassis or under seats.
Notes on electrical connections:
• Replace the fuse with one of the specified rating. If the fuse blows
frequently, consult your JVC car audio dealer.
• It is recommended to connect speakers with maximum power
of more than 50 W (both at the rear and at the front, with an
impedance of 4 Ω to 8 Ω).
• To prevent short circuits, cover the terminals of the UNUSED leads
with insulating tape.
• At the time of installation, be sure to fix all wires (wires both from
this unit and from the car itself) in a way that no wires can come
into contact with heat sinks on the rear and side of the unit.
CAUTION: Install this unit in the console of your vehicle. Do not
touch the metal parts of this unit during and shortly after the use
of the unit. Metal parts such as the heat sink and enclosure become
hot.
Heat sink
Sumidero térmico
Dissipateur de chaleur
Notas sobre las conexiones eléctricas:
• Reemplace el fusible por otro del régimen especificado. Si el
fusible se funde frecuentemente, consulte con su concesionario
de JVC de equipos de audio para automóviles.
• Se recomienda conectar los altavoces con una potencia máxima
de más de 50 W (tanto atrás como adelante, con una impedancia
de 4 Ω a 8 Ω).
• Para evitar cortocircuitos, cubra los cables NO UTILIZADOS con
cinta aislante.
• Al realizar la instalación, asegúrese de fijar todos los cables (tanto
los que proceden de esta unidad como los del vehículo en sí) de
manera tal que ninguno quede en contacto con los disipadores
térmicos de las partes traseras y laterales de la unidad.
PRECAUCIÓN: Instale esta unidad en la consola de su vehículo.
No toque las partes metálicas de esta unidad durante e
inmediatamente después de usar la unidad. Las partes metálicas,
tales como el disipador de calor y la carcasa estarán calientes.
Parts list for installation and connection
Main unit/Mounting sleeve/Trim plate
Unidad principal/Cubierta de montaje /Placa de guarnición
Appareil principal/Manchon de montage/Plaque d’assemblage
Extension wire
Cable prolongador
Fil d'extension
Antes de instalar la unidad, desconecte el terminal negativo de
la batería y realice todas las conexiones eléctricas para evitar
cortocircuitos.
• Asegúrese de volver a conectar a masa esta unidad al chasis
del automóvil después de la instalación.
• Asegúrese de que ningún cable quede atrapado en el chasis del
automóvil o debajo de los asientos.
Wiring harness
Mazo de cables
Câblage électrique
Lista de piezas para instalación y conexión
Monitor panel
Panel del monitor
Panneau du moniteur
Pour éviter tout court-circuit, débranchez la borne négative de la
batterie et effectuez tous les raccordements électriques avant d’installer
l’appareil.
• Assurez-vous de raccorder de nouveau la mise à la masse de
cet appareil au châssis de la voiture après l’installation.
• Assurez-vous qu’aucun câble n’est coincé sur châssis de la voiture ou
sous les sièges.
Remarques sur les connexions électriques:
• Remplacer le fusible par un de la valeur précisée. Si le fusible saute
souvent, consulter votre revendeur d’autoradios JVC.
• Il est recommandé de connecter des enceintes avec une puissance de
plus de 50 W (les enceintes arrière et les enceintes avant, avec une
impédance comprise entre 4 Ω et 8 Ω).
• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont
PAS UTILISÉS avec de la bande isolante.
• Au moment de l’installation, assurez-vous de fixer tous les fils (les fils
de cet appareil et aussi de la voiture elle-même) de façon qu’aucun
fil ne puisse entrer en contact avec les dissipateurs de chaleur situés à
l’arrière et sur le côté de l’appareil.
ATTENTION : Installez cet appareil dans la console de votre
véhicule. Ne touchez pas les parties métalliques de cet appareil
pendant ou juste après son utilisation. Les parties métalliques,
comme le dissipateur de chaleur et le boîtier, deviennent
chaudes.
Liste des pièces pour l’installation et
raccordement
Washer (ø5)
Arandela (ø5)
Rondelle (ø5)
Mounting bolt—M4 x 20 mm/M4 x 13/16”
Perno de montaje—M4 x 20 mm/M4 x 13/16 pulgada
Boulon de montage—M4 x 20 mm/M4 x 13/16 pouces
Extraction keys
Llaves de extracción
Clés d'extraction
Lock nut (M5)
Tuerca de seguridad (M5)
Ecrou d’arrêt (M5)
Rubber cushion
Cojín de goma
Amortisseur en caoutchouc
Only for KW-ADV65BT/KW-AV61BT
Sólo para KW-ADV65BT/KW-AV61BT
Uniquement pour le KW-ADV65BT/KW-AV61BT
Flat head screws (M5 x 8 mm/M5 x 3/8”)
Round head screws (M5 x 8 mm/M5 x 3/8”)
Tornillos de cabeza plana
(M5 x 8 mm/M5 x 3/8 pulgada)
Tornillos de cabeza esférica
(M5 x 8 mm/M5 x 3/8 pulgada)
Vis à tête plate (M5 x 8 mm/M5 x 3/8 pouces)
Vis à tête ronde (M5 x 8 mm/M5 x 3/8 pouces)
Use these screws when installing the unit
without the supplied sleeve. (See page 2.)
Utilice estos tornillos cuando instale la unidad
sin la cubierta suministrada.
(Consulte la página 2.)
Utilisez ces vis lors de l’installation de l’appareil
sans le manchon fourni. (Voir page 2.)
1
Microphone
Micrófono
Microphone
Bluetooth adapter (attached)
Adaptador Bluetooth (insertado)
Adaptateur Bluetooth (inséré)
Bag for storing the adapter
Funda para guardar el adaptador
Sac pour ranger l’adaptateur
INSTALLATION
(IN-DASH MOUNTING)
INSTALACIÓN
INSTALLATION
(MONTAJE EN EL TABLERO DE INSTRUMENTOS) (MONTAGE DANS LE TABLEAU DE BORD)
The following illustration shows a typical installation. However, you
should make adjustments corresponding to your specific car. If you
have any questions or require information regarding installation kits,
consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed
by a qualified technician.
La siguiente ilustración muestra una instalación típica. Sin embargo
usted deberá efectuar los ajustes correspondientes a su automóvil.
Si tiene alguna pregunta o necesita información acerca de las
herramientas para instalación, consulte con su concesionario de
JVC de equipos de audio para automóviles o a una compañía que
suministra tales herramientas.
• Si no está seguro de poder instalar la unidad correctamente, déjela
en manos de un técnico cualificado.
Before installing the unit
• Remove the audio system originally installed in the car, together
with its mounting brackets. Be sure to keep all the screws and parts
removed from your car for future use.
• When mounting the unit, be sure to use the screws provided, as
instructed. If other screws are used, parts could become loose or
damaged.
• When tightening screws or bolts, be careful not to pinch any
connection cord.
• Make sure not to block the fan on the rear to maintain proper
ventilation when installing the unit.
When installing the unit without using the mounting
sleeve
• Use flat head screws or round head screws, depending on
installation location. When you use flat head screws to install the
unit, use the screws removed in step 1 below. When you use screws
other than those supplied, use 8 mm (3/8”)-long screws. If longer
screws are used, they could damage the unit.
• Tighten the screws firmly to prevent the unit from falling off.
1
2
3
4
5
6
Detach the trim plate and remove the screws.
Detach the mounting sleeve using the extraction keys then slide
off the mounting sleeve.
Install the mounting sleeve in the dashboard of the car.
Do the required electrical connections.
• See pages 3 – 6.
Attach the trim plate to the main unit, then install the main unit
in to the mounting sleeve.
Attach the monitor panel.
Avant d’installer l’appareil
Antes de instalar la unidad
• Retirez le système audio d’origine installé dans la voiture en même
• Desmonte el sistema de audio instalado originalmente en el coche,
temps que les supports de montage. Assurez-vous de conserver toutes
junto con los ménsulas de montaje. Asegúrese de guardar todos los
les vis et pièces détachées de votre voiture pour une utilisation dans le
tornillos y piezas quitados de su vehículo para poderlos usar en el
future.
futuro.
• Lors du montage de l’appareil, assurez-vous d’utiliser les vis fournies,
• Al instalar la unidad, asegúrese de usar los tornillos suministrados,
de la façon indiquée. Si vous utilisez d’autres vis, certaines pièces
de acuerdo con las instrucciones. El uso de otros tornillos podrá
peuvent être perdues ou endommagées.
provocar flojedad de o daños a las piezas.
• Lorsque vous serrez des vis ou des boulons, faites attention de ne pas
• Al apretar los tornillos o los pernos, asegúrese de que ningún
pincer un cordon de connexion.
cable de conexión quede pillado.
• Assurez-vous de ne pas bloquer le ventilateur sur le panneau arrière
• Al efectuar la instalación, asegúrese de no bloquear el ventilador
lors de l’installation afin de permettre une ventilation correcte.
del panel trasero a fin de mantener una ventilación correcta.
Instalación de la unidad sin utilizar la cubierta de
montaje
Lors de l’installation de l’appareil sans utiliser de
manchon de montage
• Utilice tornillos de cabeza plana o esférica, dependiendo del lugar • Utilisez des vis à tête plate ou des vis à tête ronde, en fonction de
de instalación. Si decide utilizar tornillos de cabeza plana para
l’emplacement de l’installation. Quand vous utilisez des vis à tête
instalar la unidad, utilice los extraídos en el paso 1, más abajo.
plage pour installer l’appareil, utilisez les vis retirées à l’étape 1 ciSi decide utilizar tornillos distintos de los suministrados, escoja
dessous. Quand vous utilisez d’autres vis que les vis fournies, utilisez
tornillos de 8 mm (3/8”) de largo. El uso de tornillos más largos
des vis d’une longueur de 8 mm (3/8”). Vous risquez d’endommager
producir daños a la unidad.
l’appareil si vous utilisez des vis plus longues.
• Apriete los tornillos firmemente para evitar que la unidad se
• Serrez les vis solidement pour éviter que l’appareil tombe.
caiga.
1
2
3
4
5
6
Desmonte la placa de guarnición y extraiga los tornillos.
Con las llaves de extracción, desmonte la cubierta de montaje
deslizándola.
Instale la cubierta de montaje en el tablero de instrumentos del vehículo.
Realice todas las conexiones eléctricas necesarias.
• Consulte las páginas 3 – 6.
Fije la placa de guarnición a la unidad principal y luego inserte la
unidad principal dentro de la cubierta de montaje.
Fije el panel del monitor.
1
2
Mounting sleeve
Cubierta de montaje
Manchon de montage
1
2
3
4
5
6
Détachez la plaque d’assemblage et retirez les vis.
Détachez le manchon de montage en utilisant les clés d'extraction
puis faites le glisser vers l'extérieur pour le retirer.
Installez le manchon de montage dans le tableau de bord de la voiture.
Réalisez les connexions électriques.
• Voir pages 3 – 6.
Attachez la plaque de garniture sur l'appareil principale, puis
installez l'appareil dans le manchon de montage.
Attachez le panneau du moniteur.
When you stand the unit, be careful
not to damage the fuse on the rear.
Extraction key
Llaves de extracción
Clés d'extraction
Flat head screws (M5 x 8 mm/M5 x 3/8”)
Tornillos de cabeza plana
(M5 x 8 mm/M5 x 3/8 pulgada)
Vis à tête plate (M5 x 8 mm/M5 x 3/8 pouces)
3
L’illustration suivante est un exemple d’installation typique.
Cependant, vous devez faire les ajustements correspondant à votre
voiture. Si vous avez des questions ou avez besoin d’information sur des
kits d’installation, consulter votre revendeur d’autoradios JVC ou une
compagnie d’approvisionnement.
• Si vous n’êtes pas sûr de pouvoir installer l’appareil correctement,
faite-le installer par un technicien qualifié.
Al poner la unidad vertical, tenga
cuidado de no dañar el fusible
provisto en la parte posterior.
Trim plate
Placa de guarnición
Plaque d’assemblage
Mounting sleeve
Cubierta de montaje
Manchon de montage
Lorsque vous mettez l’appareil à la
verticale, faire attention de ne pas
endommager le fusible situé sur
l’arrière.
Mounting sleeve
Cubierta de montaje
Manchon de montage
4
For more stable attachment
Para una fijación más estable
Pour que la fixation soit plus stable
A Stay (option) / Soporte (opción) / Hauban (en option)
B Screw (option) / Tornillo (opción) / Vis (en option)
C Lock nut / Tuerca de seguridad / Ecrou d’arrêt
D Washer / Arandela / Rondelle
E Mounting bolt / Perno de montaje / Boulon de montage
A
Bend the appropriate tabs to hold the mounting sleeve firmly in place.
B
Doble las lengüetas apropiadas para retener firmemente la cubierta de
montaje en su lugar.
C
D E
To the rear panel
Al panel trasero
Sur le panneau arrière
Tordez les languettes appropriées pour maintenir le manchon de montage en place.
5
6
Trim plate
Placa de guarnición
Plaque d’assemblage
Mounting sleeve
Cubierta de montaje
Manchon de montage
Do not block the fan.
No tape las rejillas de ventilación.
Ne bloquez pas le ventilateur.
Slide the unit in until you hear a clicking sound.
Deslice la unidad hasta escuchar un chasquido.
Monitor panel
Panel del monitor
Panneau du moniteur
Faites glisser l’appareil jusqu’à ce que vous entendiez un clic.
OK
DO NOT press the panel (shaded in the illustration).
NO presione el panel (sombreado en la ilustración).
NE POUSSEZ PAS sur le panneau (en gris sur l’illustration).
2
Install the unit at an angle of less
than 30˚.
Instale la unidad a un ángulo de
menos de 30˚.
Installez l’appareil avec un angle de
moins de 30°.
30˚
Removing the unit
Extracción de la unidad
Retrait de l’appareil
Before removing the unit, release the rear section.
Antes de extraer la unidad, libere la sección trasera.
Avant de retirer l’appareil, libérer la section arrière.
1
Detach the monitor panel (see
page 5 of the INSTRUCTION
MANUAL).
Desmonte el panel del monitor
(consulte la página 5 del
MANUAL DE INSTRUCCIONES).
Détachez le panneau du moniteur
(voir la page 5 du MODE
D’EMPLOI).
2
3
Detach the trim plate.
Desmonte la placa de
guarnición.
Détachez la plaque
d’assemblage.
Trim plate
Placa de guarnición
Plaque d’assemblage
ELECTRICAL CONNECTIONS
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the wiring harness
to the car battery; otherwise, the unit will be seriously
damaged.
• BEFORE connecting the speaker leads of the wiring harness to the
speakers, check the speaker wiring in your car.
Insert the two extraction keys, then pull
them as illustrated so that the unit can be
removed.
Inserte las dos llaves de extracción y, a
continuación, extráigalas de la manera
indicada en la ilustración para que la
unidad pueda desmontarse.
Insérez les deux clés d'extraction, puis tirez de
la façon illustrée de façon à retirer l’appareil.
Extraction key
Llaves de extracción
Clés d'extraction
CONEXIONES ELECTRICAS
RACCORDEMENTS ELECTRIQUES
PRECAUCIONES sobre las conexiones de la fuente de
alimentación y de los altavoces:
• NO conecte los cables de los altavoces del mazo de cables a la
batería del coche, de lo contrario, la unidad quedará seriamente
dañada.
• ANTES de conectar los cables de los altavoces del mazo de cables
a los altavoces, revise el cableado de los altavoces de su coche.
PRECAUTIONS sur l’alimentation et la connexion des
enceintes:
• NE CONNECTEZ PAS les fils d’enceintes du câblage
électrique à la batterie; sinon, l’appareil serait
sérieusement endommagé.
• AVANT de connecter les fils d’enceintes du câblage électrique aux
enceintes, vérifiez le câblage des enceintes de votre voiture.
Connecting the parking brake lead / Conexión del cable del freno de estacionamiento / Connexion du fil de frein de stationnement
Parking brake lead (light green)
Cable del freno de estacionamiento (verde claro)
Fil du frein de stationnement (vert clair)
Extension wire (supplied)
Cable prolongador (suministrado)
Fil d'extension (fourni)
Parking brake
Freno de estacionamiento
Frein de stationnement
KW-ADV65BT
KW-AV61BT/KW-AV61
To metallic body or chassis of the car
A un cuerpo metálico o chasis del automóvil
Vers corps métallique ou châssis de la voiture
Parking brake switch (inside the car)
Interruptor del freno de estacionamiento (dentro del automóvil)
Commutateur de frein de stationnement (intérieur de la voiture)
Connecting the reverse gear signal lead (for rear view camera) / Conexión del cable de señal del engranaje de marcha atrás (para cámara de retrovisión) /
Connexion du fil de signal de marche arrière (pour la caméra de recul)
Locate the reverse lamp lead in the trunk.
Purple with white stripe
Púrpura con rayas blancas
Violet avec bande blanche
KW-ADV65BT
KW-AV61BT/KW-AV61
Localisez le fil des feux de recul dans le coffre.
Localice el conductor de la luz de marcha atrás en el
portaequipajes.
Extension wire (not supplied for this unit)
Cable prolongador (no suministrado con esta unidad)
Fil d'extension (non fourni avec cet autoradio)
To reverse lamp
A la luz de marcha atrás
Aux feux de recul
Reverse lamp lead
Conductor de la luz de
marcha atrás
Fil des feux de recul
3
Reverse lamps
Luz de marcha atrás
Feux de recul
ENGLISH
ESPAÑOL
Before connecting: Check the wiring in the vehicle carefully.
Incorrect connection may cause serious damage to this unit.
The leads of the wiring harness and those of the connector from the
car body may be different in color.
1
Connect the colored leads of the wiring harness in the order
specified in the illustration below.
2
3
Connect the antenna cord.
Antes de la conexión: Verifique atentamente el conexionado del
vehículo. Una conexión incorrecta podría producir daños graves en
la unidad.
Los colores de los cables del mazo de cables y los del conector de la
carrocería del coche pueden ser diferentes.
1
2
3
Finally connect the wiring harness to the unit.
FRANÇAIS
Avant de commencer la connexion: Vérifiez attentivement le
câblage du véhicule. Une connexion incorrecte peut endommager
sérieusement l’appareil.
Les fils du câblage électrique et ceux des connecteurs du châssis de la
voiture peuvent être différents en couleur.
Conecte los cables de colores del mazo de cables en el orden
especificado en la siguiente ilustración.
1
Conecte el cable de antena.
2
3
Por último, conecte el cable de alimentación a la unidad.
Connectez le cordon d’antenne.
Finalement, connectez le faisceau de fils à l’appareil.
• Les prises et les câbles de tous les modèles sont montrés sur les
illustrations dans un but explicatif.
• The terminals and cables of all models are shown in the illustration • Los terminales y cables de todos los modelos se muestran en la
ilustración con fines explicativos.
for the purpose of explanation.
Light green
Verde claro
Vert clair
Connectez les fils colorés du câblage électrique dans l’ordre spécifié
sur l’illustration ci-dessous.
To parking brake (see page 3)
Al freno de estacionamiento (consulte la página 3)
Au frein de stationnement (voir page 3)
Extension wire (supplied) / Cable prolongador (suministrado) / Fil d'extension (fourni)
(see page 3 / consulte la página 3 / voir page 3)
See each diagram on pages 4 – 6.
Vea cada uno de los diagramas en las páginas 4 – 6.
Référez-vous à chaque diagramme des pages 4 – 6.
Fan
Ventilador
Ventilateur
*1
10 A fuse / Fusible de 10 A / Fusible 10 A
Antenna
terminal
Terminal de
la antena
Borne de
l’antenne
*2
Black
Negro
Noir
Rear ground terminal
Terminal de tierra posterior
Borne arrière de masse
*3
To metallic body or chassis of the car
A un cuerpo metálico o chasis del automóvil
Vers corps métallique ou châssis de la voiture
Yellow *4
Amarillo *4
Jaune *4
To an accessory terminal in the fuse block
A un terminal accesorio del bloque de fusibles
Vers borne accessoire du porte-fusible
Blue
Azul
Bleu
To automatic antenna if any (250 mA max.)
A la antena automática, si hubiere (250 mA máx.)
À l’antenne automatique s’il y en a une (250 mA max.)
Blue with white stripe
Azul con rayas blancas
Bleu avec bande blanche
To car light control switch
Al interruptor de control de las luces del automóvil
À l’interrupteur d’éclairage de la voiture
Brown
Marrón
Marron
Connecting the Bluetooth adapter (Only for KW-AV61)
Conexión del adaptador Bluetooth (Sólo para KW-AV61)
Connexion de l’adaptateur Bluetooth (Uniquement pour le KW-AV61)
Light blue with yellow stripe
Azul claro con rayas amarillas
Bleu clair avec bande jaune
Gray with black stripe
Gris con rayas negras
Gris avec bande noire
Left speaker (front)
Altavoz izquierdo (delantero)
Enceinte gauche (avant)
A
Gray
Gris
Gris
Fuse block
Bloque de
fusibles
Porte-fusible
To the remote lead of other equipment (200 mA max.)
Al conductor remoto del otro equipo (200 mA máx.)
Au fil de télécommande d’un autre appareil (200 mA max.)
Orange with white stripe
Naranja con rayas blancas
Orange avec bande blanche
White
Blanco
Blanc
*3
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
A un terminal activo del bloque de fusibles conectado a la batería del
automóvil (desviando el interruptor de encendido) (12 V constantes)
A une borne sous tension du porte-fusible connectée à la batterie de la voiture (en
dérivant l’interrupteur d’allumage) (12 V constant)
Red
Rojo
Rouge
White with black stripe
Blanco con rayas negras
Blanc avec bande noire
Ignition switch
Interruptor de encendido
Interrupteur d’allumage
To the OE remote adapter *5
Al adaptador para control remoto OE *5
Au adaptateur pour télécommande au volant *5
Green
Verde
Vert
Green with black stripe
Verde con rayas negras
Vert avec bande noire
Right speaker (front)
Altavoz derecho (delantero)
Enceinte droit (avant)
Purple with black stripe
Púrpura con rayas negras
Violet avec bande noire
Left speaker (rear)
Altavoz izquierdo (trasero)
Enceinte gauche (arrière)
Purple
Púrpura
Violet
Right speaker (rear)
Altavoz derecho (trasero)
Enceinte droit (arrière)
Connecting to the steering wheel remote controller / Conexión al control remoto del volante de dirección / Connexion de la télécommande
de volant
OE remote adapter *3 *6
Adaptador remoto OE *3 *6
Adaptateur pour télécommande au volant *3 *6
If your car is equipped with the steering wheel remote controller, you can operate this unit using the
controller. For connection, an exclusive remote adapter (not supplied) which matches your car is
required. For details, consult the same car audio dealer as where the unit is purchased.
Si su vehículo está equipado con control remoto en el volante de dirección, podrá hacer funcionar este receptor
utilizando dicho control. Para la conexión, se requiere un adaptador remoto exclusivo (no suministrado) que sea
adecuado para su automóvil. Para los detalles, consulte con el concesionario car audio donde compró el receptor.
Si votre voiture est munie d’une télécommande de volant, vous pouvez commander cet autoradio en utilisant la
télécommande. Pour la connexion, un adaptateur de télécommande exclusif (non fourni) correspondant à votre voiture
est requis. Pour en savoir plus, consultez le revendeur autoradio auprès duquel vous avez acheté cet autoradio.
*1 Only for KW-ADV65BT/KW-AV61BT.
*2 Only for KW-ADV65BT Region 1/KW-AV61BT Region1/
KW-AV61 Region 1.
*3 Not supplied for this unit.
4
* Before checking the operation of this unit prior to installation, this lead
must be connected, otherwise power cannot be turned on.
Do not connect the lead directly to the battery.
5
* Do not connect the lead to any device other than the OE remote
adapter. Doing so may cause malfunction.
*6 Alter the wire of the OE remote adapter to connect to the steering wheel
remote lead.
KW-ADV65BT
KW-AV61BT/KW-AV61
*1 Sólo para KW-ADV65BT/KW-AV61BT.
*2 Solo para KW-ADV65BT Región 1/KW-AV61BT Región1/KW-AV61
Región 1.
*3 No suministrado con esta unidad.
*4 Antes de comprobar el funcionamiento de esta unidad previa a de la
instalación, es necesario conectar este cable, de lo contrario no se podrá
conectar la alimentación. No conecte el conductor directamente a la batería.
*5 No conecte el cable a ningún otro dispositivo que no sea el adaptador para
control remoto OE. De lo contrario podría provocar un mal funcionamiento.
*6 Altere el cableado del adaptador para control remoto OE para
conectar al conductor remoto del volante de dirección.
4
Steering wheel remote controller (equipped in the car)
Control remoto del volante de dirección (equipado
en el vehículo)
Télécommande de volant (installée dans la voiture)
*1 Uniquement pour le KW-ADV65BT/KW-AV61BT.
*2 Uniquement pour le KW-ADV65BT Région 1/KW-AV61BT Région1/
KW-AV61 Région 1.
*3 Non fourni avec cet appareil.
*4 Pour vérifier le fonctionnement de cet appareil avant installation, ce fil
doit être raccordé, sinon l’appareil ne peut pas être mis sous tension.
Ne connectez pas le fil directement à la batterie.
*5 Ne connectez pas ce fil à aucun autre appareil que l’adaptateur de
télécommande au volant. Cela pourrait causer un mauvais fonctionnement.
*6 Modifiez le fil de l’adaptateur de télécommande au volant pour le
connecté au fil de télécommande de volant.
B
Connecting the external amplifiers and subwoofer / Conexión de los amplificadores y subwoofer / Connexion d’amplificateurs extérieurs et
d’un caisson de grave
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote
lead of the other equipment so that it can be controlled through
this unit.
• Disconnect the speakers from this unit, and connect
them to the amplifier. Leave the speaker leads of this unit
unused.
• You can switch off the built-in amplifier and send the audio
signals only to the external amplifier(s) to get clear sounds and to
prevent internal heat built-up inside the unit. See page 46 of the
INSTRUCTION MANUAL.
Remote lead *7
Cable remoto *7
Fil d’alimentation à distance *7
Puede conectar amplificadores para mejorar su sistema car estéreo.
• Conecte el conductor remoto (azul con rayas blancas) al
conductor remoto del otro equipo para poderlo controlar a través
de esta unidad.
• Desconecte los altavoces de esta unidad y conéctelos al
amplificador. Los cables de los altavoces de esta unidad quedan
sin usar.
• Podrá desconectar el amplificador incorporado y enviar las
señales de audio solamente al(los) amplificador(es) externo(s)
para obtener sonidos nítidos y evitar que se caliente el interior de
la unidad. Consulte la página 46 del MANUAL DE INSTRUCCIONES.
Y-connector *7 / Conector en Y *7 / Connecteur Y *7
To the remote lead of other equipment
Al conductor remoto del otro equipo
Au fil de télécommande d’un autre appareil
*8
Remote lead (blue with white stripe)
Cable remoto (azul con rayas blancas)
Fil d’alimentation à distance (bleu avec
bande blanche)
Front speakers
Altavoces delanteros
Enceintes avant
JVC Amplifier
Amplificador de JVC
JVC Amplificateur
Rear speakers
Altavoces traseros
Enceintes arrière
KW-ADV65BT
KW-AV61BT/KW-AV61
*8
*8
JVC Amplifier
Amplificador de JVC
JVC Amplificateur
*9
JVC Amplifier
Amplificador de JVC
JVC Amplificateur
*9
C
Vous pouvez connecter un amplificateur pour améliorer votre système
autoradio.
• Connectez le fil de commande à distance (bleu avec bande blanche)
au fil de commande à distance de l’autre appareil de façon qu’il
puisse être commandé via cet appareil.
• Déconnectez les enceintes de cet appareil et connectez-les à
l’amplificateur. Laissez les fils d’enceintes de cet appareil inutilisés.
• Vous pouvez mettre hors service l’amplificateur intégré et envoyer les
signaux audio uniquement sur un ou plusieurs amplificateurs extérieurs
afin d’obtenir un son clair et d’éviter tout échauffement interne de
l’autoradio. Voir page 46 du MODE D’EMPLOI.
Subwoofer
Subwoofer
Caisson de grave
*9
Connecting the external components / Conectando los componentes externos / Connexion des appareils extérieurs
KV-CM10 / KV-CM20 *7
Rear view camera
Cámara de reprovisión
Caméra de recul
KW-ADV65BT
KW-AV61BT/KW-AV61
10
Camcorder etc.
Videocámara etc.
Caméscope etc.
10
External monitor
Monitor externo
Moniteur extérieur
8
Connecting the iPod or the iPhone / Conexión del iPod o iPhone / Connexion d’un iPod ou d’un iPhone
• To watch video, connect the iPod/iPhone using JVC KS-U30 *11 (separately purchased), otherwise,
video is not displayed on the screen.
• To listen to music, connect the iPod/iPhone using a USB 2.0 cable (accessory of the iPod/iPhone).
USB 2.0 cable (accessory of the iPod/iPhone) /
Cable USB 2.0 (accesorio del iPod/iPhone) /
Câble USB 2.0 (accessoire du iPod/iPhone)
• Para ver video, conecte el iPod/iPhone mediante el JVC KS-U30 *11 (en venta por separado); de lo
contrario, no aparecerá video en la pantalla.
• Para escuchar música, conecte el iPod/iPhone mediante un cable USB 2.0 (accesorio del iPod/
iPhone).
• Pour voir une séquence vidéo, connectez l’iPod/iPhone en utilisant le JVC KS-U30 *11 (vendu
séparément), sinon, l’image vidéo n’apparaît pas sur l’écran.
• Pour écouter la musique, connectez l’iPod/iPhone en utilisant le câble USB 2.0 (accessoire du iPod/
iPhone).
KS-U30
KW-ADV65BT
KW-AV61BT/KW-AV61
(not supplied / no suministrado /
non fourni)
USB devices / Dispositivos USB / Périphériques USB
USB cable (approx. 1 m / 3.3 feet)
Cable USB (aprox. 1 m / 3.3 pies)
Câble USB (environ 1 m / 3.3 pieds)
USB device
Dispositivo USB
Périphérique USB
KW-ADV65BT
KW-AV61BT
KW-AV61
*7 Not supplied for this unit.
*8 Audio cord (not supplied for this unit).
*9 Firmly attach the ground wire to the metallic body or to the chassis of
the car—to the place uncoated with paint (if coated with paint, remove
the paint before attaching the wire). Failure to do so may cause damage
to the unit.
*10 Video cord (not supplied for this unit).
*11 When using the cable, you need to change the setting on the unit (see
page 26 of the INSTRUCTION MANUAL).
*7 No suministrado con esta unidad.
*8 Cable de audio (no suministrado con esta unidad).
*9 Fije firmemente el cable de tierra a la carrocería metálica o al chasis—a
un lugar no cubierto con pintura (si está cubierto con pintura, quítela
antes de fijar el cable). De lo contrario, se podrían producir daños en la
unidad.
*10 Cordón de video (no suministrado con esta unidad).
*11 Cuando utilice el cable, deberá cambiar el ajuste en la unidad (consulte la
página 26 del MANUAL DE INSTRUCCIONES).
5
*7 Non fourni avec cet appareil.
*8 Cordon audio (non fourni avec cet appareil).
*9 Attachez solidement le fil de mise à la masse au châssis métallique de la
voiture—à un endroit qui n’est pas recouvert de peinture (s’il est recouvert
de peinture, enlevez d’abord la peinture avant d’attacher le fil). L’appareil
peut être endommagé si cela n’est pas fait correctement.
*10 Cordon vidéo (non fourni avec cet appareil).
*11 Lors de l’utilisation du câble, vous devez changer le réglage sur l’appareil
(voir page 26 du MODE D’EMPLOI).
D
Connecting the microphone (Only for KW-ADV65BT/KW-AV61BT) / Conexión de la unidad de micrófono (Sólo para KW-ADV65BT/KWAV61BT) / Connexion du microphone (Uniquement pour le KW-ADV65BT/KW-AV61BT)
3
2
1
Microphone
Micrófono
Microphone
Secure the microphone cord using cord clamps
(not supplied) if necessary.
Adhesive tape
Cinta adhesiva
Ruban adhésif
Si es necesario, asegure el cable del micrófono
por medio de abrazaderas (no suministradas).
Fixez si nécessaire le cordon du microphone en
utilisant des serre-fils (non fournis).
KW-ADV65BT
KW-AV61BT
E
Connecting the Bluetooth adapter (Only for KW-AV61) / Conexión del adaptador Bluetooth (Sólo para KW-AV61) /
Connexion de l’adaptateur Bluetooth (Uniquement pour le KW-AV61)
KS-BTA100 *12
KW-AV61
To the blue with white stripe lead of the supplied wiring harness 5
Blue with white stripe / Azul con rayas blancas / Al cable azul con rayas blancas del mazo de cables suministrado 5
Bleu avec bande blanche
Au fil bleu avec une bande blanche du câblage élecrique 5 fourni
*12
Ground / Tierra / Masse
Black / Negro / Noir
To the brown lead of the supplied wiring harness 7
Al cable marrón del mazo de cables suministrado 7
Au fil marron du câblage élecrique 7 fourni
Brown / Marrón / Marron
See page 61 of the INSTRUCTION MANUAL. / Consulte la página 61 del MANUAL DE INSTRUCCIONES. / Voir page 61 du MODE D’EMPLOI.
F
Connecting the SiriusXM tuner (Only for KW-ADV65BT Region 1/KW-AV61BT Region1/KW-AV61 Region 1) /
Conexión del sintonizador SiriusXM (Solo para KW-ADV65BT Región 1/KW-AV61BT Región1/KW-AV61 Región 1) /
Connexion du tuner SiriusXM (Uniquement pour le KW-ADV65BT Région 1/KW-AV61BT Région1/ KW-AV61 Région 1.)
When connecting the SiriusXM tuner, refer also to the manual
supplied for it.
CAUTION: Before connecting the SiriusXM tuner, make sure that
the unit is turned off.
Cuando conecte el sintonizador SiriusXM, consulte también el
manual suministrado con el mismo.
PRECAUCIÓN: Antes de conectar el sintonizador SiriusXM,
asegúrese de que la unidad esté apagada.
KW-ADV65BT
KW-AV61BT
KW-AV61
SiriusXM tuner
Sintonizador SiriusXM
Tuner SiriusXM
PRECAUTION: Avant de connecter le tuner SiriusXM, assurez-vous
que l’appareil est hors tension.
To disconnect the connector
Para desconectar el conector
Pour déconnecter le connecteur
Grip the connector top tightly ( 1 ).
Sostenga el conector con firmeza (1).
Tenez fermement le haut de l’adaptateur ( 1 ).
Expansion port
Puerto de extensión
Port d’extension
*12 Not supplied for this unit.
Lors de la connexion du tuner SiriusXM tuner, reportez-vous aussi au
mode d’emploi qui l’accompagne.
*12 No suministrado con esta unidad.
*12 Non fourni avec cet appareil.
TROUBLESHOOTING
LOCALIZACIÓN DE AVERIAS
EN CAS DE DIFFICULTES
•
*
•
*
•
*
•
*
*
•
*
•
*
•
*
•
*
•
*
*
•
*
•
*
•
*
•
*
*
•
*
*
•
*
The fuse blows.
Are the red and black leads connected correctly?
Power cannot be turned on.
Is the yellow lead connected?
No sound from the speakers.
Is the speaker output lead short-circuited?
Sound is distorted.
Is the speaker output lead grounded?
Are the “–” terminals of L and R speakers grounded in common?
Noise interfere with sounds.
Is the rear ground terminal connected to the car’s chassis using
shorter and thicker cords?
This unit becomes hot.
Is the speaker output lead grounded?
Are the “–” terminals of L and R speakers grounded in common?
This unit does not work at all.
Have you reset your unit?
•
*
•
*
*
•
*
El fusible se quema.
¿Están los conductores rojo y negro correctamente conectados?
No es posible conectar la alimentación.
¿Está el cable amarillo conectado?
No sale sonido de los altavoces.
¿Está el cable de salida del altavoz cortocircuitado?
El sonido presenta distorsión.
¿Está el cable de salida del altavoz conectado a masa?
¿Están los terminales “–” de los altavoces L y R conectados a una
masa común?
Perturbación de ruido.
¿El terminal de tierra trasero está conectado al chasis del
automóvil utilizando los cordones más corto y más grueso?
La unidad se calienta.
¿Está el cable de salida del altavoz conectado a masa?
¿Están los terminales “–” de los altavoces L y R conectados a una
masa común?
Este receptor no funciona en absoluto.
¿Reinicializó el receptor?
6
Pull out ( 2 ).
Extráigalo ( 2 ).
Tirez ( 2 ).
•
*
•
*
*
•
*
Le fusible saute.
Les fils rouge et noir sont-ils racordés correctement?
L’appareil ne peut pas être mise sous tension.
Le fil jaune est-elle raccordée?
Pas de son des enceintes.
Le fil de sortie d’enceinte est-il court-circuité?
Le son est déformé.
Le fil de sortie d’enceinte est-il à la masse?
Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble
à la masse?
Interférence avec les sons.
La prise arrière de mise à la terre est-elle connectée au châssis de la
voiture avec un cordon court et épais?
L’appareil devient chaud.
Le fil de sortie d’enceinte est-il à la masse?
Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble
à la masse?
Cet appareil ne fonctionne pas du tout.
Avez-vous réinitialisé votre appareil?
KW-AV61BT/KW-AV61/KW-ADV65BT
iPhone/iPod users:
PLEASE READ THIS BEFORE USING YOUR NEW UNIT
You have two options when connecting an
iPhone or an iPod to your new unit:
■ Option 1 (Default Setting):
Using the optional JVC KS-U30
Your unit is pre-set from the factory to allow
audio and video playback when you connect
your iPhone or iPod using the optional JVC KS-U30
cable (Sold Separately). If you purchased the KSU30, simply connect your iPhone or iPod using
this optional cable.
Setting <AV Input> for iPod/iPhone playback
Configuración de <AV Input> para la reproducción
de iPod/iPhone
Réglage <AV Input> pour la lecture du iPod/iPhone
1
2
■ Option 2 :
If you wish to connect your iPhone or iPod with
white 30-Pin iPod USB Cable (this is the white
cable that is supplied with your iPhone or iPod),
you will need to follow the simple steps below to
assure audio playback:
Please go to [HOME] > > Select [AV Off] >>
Select [HOME] >> Select [Settings] >> [Input],
then select [AV-IN] at “AV Input” Menu.
3
1
Important Notice:
When you using your white 30-Pin iPod USB
Cable, audio signal does not come through via
USB if you select “iPod”. You must select “AV-IN”
when using your white 30-Pin iPod USB Cable.
2
GET0884-005A
Usuarios de iPhone o iPod:
Por favor lea esto antes de usar su nueva unidad
Utilisateurs d’iPhone et d’iPod:
Veuillez lire ceci avant d’employer votre nouvelle unité
Usted tiene dos opciones cuando usted que
conecta un iPhone o un iPod con su nueva unidad:
Vous avez deux options quand vous reliant
un iPhone ou un iPod a votre nouvelle unite:
■ Opción 1 (Ajuste Predeterminado): ■ Option 1 (Arrangement de defaut):
Usando el accesorio opcional
Utilisant le JVC KS-U30 en option
Votre unité est préréglée de l’usine pour
JVC modelo KS-U30
Su unidad viene pre-ajustada de fabrica
para permitir la reproducción de audio y
video cuando Ud. Conecte su iPhone o iPod
utilizando el cable opcional JVC modelo
KS-U30 (vendido por separado). Si usted
compró el ks-u30, conecte simplemente su
iPhone o iPod usando este cable opcional.
permettre le lecture audio et vidéo quand vous
reliez votre iPhone ou iPod en utilisant le câble
JVC KS-U30 en option (vendu séparément).
Si vous avez achetez le KS-U30, reliez
simplement votre iPhone ou iPod en utilisant
ce câble en option.
■ Opción 2 :
■ Option 2 :
Si usted desea conectar su iPhone o iPod
con el cable USB de 30-Pines iPod (éste es el
cable blanco que se suministra su iPhone o
iPod), usted necesitará seguir los siguientes
pasos para la reproducción de audio :
Si vous voulez relier votre iPhone ou iPod
au câble blanc d’USB de 30-Pin iPod (c’est le
câble blanc qui est fourni avec votre iPhone
ou iPod), vous devrez suivre l’étape ci-dessous
pour assurer le lecture audio:
Presione [HOME] >>
Seleccione [AV Off] >>
Seleccione [HOME] >>
Seleccione [Settings] >>[Input], Entonces,
seleccione [AV-IN] en el Menú “AV Input”.
Veuillez aller à [HOME] > >
Choisissez [AV Off] >>
Choisissez [HOME] >>
Choisissez [Settings] >>[Input], Puis,
sélectionner [AV-IN] au Menu “AV Input”.
Aviso importante:
Si al usar el cable USB de iPod de 30 pines
blanco, la señal de audio no llega vía USB al
seleccionar iPod. Usted deberá seleccionar
“AV-IN” al usar su cable USB de iPod de 30
pines.
Notification importante:
En utilisant le câble USB pour iPod à 30-Pin
blanc, le signal audio n’apparaît pas par USB
si vous choisissez “iPod”. Vous devez choisir
“AV-IN” quand vous utilisez votre câble USB
pour iPod blanc à 30-Pin.
When it is. not required to detach
the front control panel from
the main unit, use the
provided screws to
attach the control
panel to the
mai·n unit.
LV45426- 001 A
0
~!
Do not~ use any solve~t (fq_~,· , exarbple, thi*p.er, ben~!le, ~tc.), ~
the monTtor orlthe anit.
detergent, or"fri.seoticide. J;ji'j$.::W~y damage
,
..·i\..-·.-- ··=·. · ,;:.
~--
-c- - - , .. - ~ · -~·~·-, '«HIP£'Pilil&¥YN¥'ttsrr;rr~r
~
- 1 ·~.~ 1x
~ ~~-
::;, :::. -c.
~
~
0
en~
~
0
~
10
·· ·
~· ··:-.:' u· r
-A
. _·
\·~-.~.
i , -- -:
~-·
-- · ·
-
L
~.-
N~ CONNECTBLACKWIRE((i)GND)TOGROUNDFIRST.
_OTHERWISE,
I
DAMAGE TO YOUR UNIT MAY OCCUR.
5 1:. CDl'
. ND FIRST
CONNECT GROU
~ ~--~--------------------~------------------------~
~
i6
~ ~t:
_.
!a8~
i!= ffi li:i
w ~ (.)
~ w [ij
:E 0:: 0::
ffi
ffi 0::
0::
y
I=
"'~~~
:E w u
a::
c··
;_ 1 •
INCORRECT CONNECnON CAUSES SERIOUS DAMAGE TO THIS UNIT
PLEASE READ INSTALLAnON/CONNECTION MANUAL CAREFULLY.
[; ....
w
~
! .
i!cC
--'
~ · · :-- ~· ~ .--~ ··'~--~,.sr
.G)
/
, =~~YORCHASSIS
.
~-
\6)
CONNECT OTHER WIRES
~~
~
CANADA
ONLY
JVC
CANADA
SEULEMENT
WARRANTY
GAlANTII
OWNER'S COPY OF WARRANTY CARD
COPIE D'ENREGISTREMENT DE LA GARANTIE
DU PROPRIETAIRE
(Save sales docket together with this warranty card, as a proof of date of purchase.
La facture et cette garantie sont vos preuves de Ia date d'achat; rangez-les.)
MODEL .
SERIAL NO.
MODELE . ........................................................ NO DE SERlE
Purchase from.
Achete chez ·
Dealer's Address
.
Adresse du Vendeu(
No.
No
Rue
City or Town
Prov.
Ville
Prov.
Owner's Name
.
Nom du Proprietaire :... .. ........... ..... .
Owner's Address
.
Adresse du Proprietaire·........ ..
No.
No
.... .................. •...••••.• •••••.•• .•
City or Town
Ville
Prov.
Prov.
.
·
Date purchased .
·
Date achete
JVC CANADA INC.
6070 kestrel Road, Missisauga, Ontario, LST 1S8 Canada
TEL: (905) 670-3381 FAX: (905)670-7244
Postal Code
Code Postal
Street
Apt.
Rue
App.
................................................... .........................
Postal Code
Code Postal
http://www.jvc.ca
JVC CANADA INC. (hereafter called "JVC") gives
the following express warranty for each new JVC
product distributed in Canada by JVC and sold
by an authorized JVC dealer.
JVC warrants that this JVC product is free, under
normal use and maintenance, from any defects in
material and workmanship subject to the following
terms and conditions:
JVC CANADA INC. ( ci-apres appele "JVC")
enonce Ia garantie expresse suivante pour tout
nouveau produit JVC distribue au Canada par JVC
et vendu par un detaillant JVC autorise.
JVC vous garantit que ce produit est degage, sous
utilisation et entretien normal, de tout defaut
materiel et de fabrication sous reserve des
modalites et conditions suivantes :
1. To Obtain Warranty Service:
1. Pour obtenir un service de garantie :
(a) JVC Product requiring service must be
Presented together with Proof of purchase.
BT-52009-1
(0912)
Printed in Indonesia
Product Registration/Enregistrement du produit
We suggest that you register your product since it will enable us
to contact you directly if it is ever necessary to correct a safety related
condition in your product.
(b) The JVC product must be brought in for
service to an authorized JVC Service Centre.
2. Limitation :
This Warranty shall not apply to:
(a) Repair or replacement of any cabinets,
batteries, plates, connection cords, antennas, dust covers, knobs, speaker grills,
speaker cones, projection screens, projection
screen savers, and all accessories.
You can register at http://www.jvc.ca/www/Support/Warranty.aspx
(b) Any defects caused or repairs required as a
result of misuse, abusive operation, negligence, improper use and/or insufficient care.
Nous vous conseillons d'enregistrer votre produit, car il nous permettra de vous
(c) Any defect caused or repairs required as
a result of not following the instructions in
the operation manual.
contacter directement
si jamais elle est necessaire pour corriger un probleme lie a Ia securite de votre
produit.
Vous pouvez vous inscrire a http://www.jvc.ca/www/Support/Warranty.aspx
(d) Any JVC product tampered with, adjusted
or repaired by any party other than JVC or
authorized JVC Service Centre personnel.
(a) Les produits jvc necessitant un service doit
etre presentee avec Ia prenve d'achat
(b) Le produit JVC doit etre apports pour
service chez un centre de service JVC
autorise.
2. Restrictions :
Cette garantie ne s'applique pas aux :
(a) Reparation ou remplacement de tout
cabinet, batteries, panneau avant, cordons
de raccord, antennas, housses de
protection, boutons, couverts de hautparleur, cones de haut-parleur, ecrans de
projection, protecteurs d'ecran de projection
et tous les accessoires.
(b) Tous defauts occasionnes ou reparations
requises suite a une utilisation abusive,
mauvaise, negligente eUou une utilisation
incorrecte.
(c) Tous defauts occasionnes ou reparations
requises suite a !'omission de suivre les
recommandations du manuel d'instruction.
(d) Tout produit JVC altere, ajuste ou repare par
tout autre entreprise que JVC ou un centre
de service d'entretien ou de service
autorise JVC.
(e) Any JVC products on which the serial
num-ber has been defaced, modified or
removed.
(f) Maintenance, cleaning or periodic check-up
(g) Conversion to foreign or domestic voltage or
frequency.
(h) Any JVC product without the Canadian
Electrical Safety Regulations ID.
( i ) Any JVC products used for commercial or
institutional, rental, or display purposes.
Parts .. . ... 1 year (except video head - 90
days)
Labour .. . 90 days
(j) Any JVC product which has been resold and
no longer owned by the original purchaser.
(k) Product purchased from "outside Canada",
"bankruptcy" or "liquidator".
(e) Tout produit JVC doni le numero de serie a
ete altere, modifie ou enleve.
(f) L'entretien, les verifications periodiques et
nettoyage.
(g) La conversion
une frequence ou une
tension etrangere ou domestique.
(h) Tout produit JVC n'ayant pas le sigle
d'identification conforme aux normes
electriques Canadiennes (CSA).
(i) Pour tout p roduit utilise
des fins
commerciales, institutionnelles, de location
ou utilise des fins d'etalage.
Pieces...... .. .. .. 1 An (Excepte les tiHes
video- 90 jours)
Main d'ceuvre . .. 90 Jours
U) Tout produit JVC ayant ete revendu et qui
n'est plus Ia propriete de l'acheteur original.
(k) Produit achete
"l'exterieur du Canada",
provenant d'une "faillite" ou d'un "liquidateur".
a
a
a
a
WARRANTYTERM (VALID FROM THE DATE OF PURCHASE)
CONDITIONS DE GARANTIE (VALABLE a PARTIR DE LA DATE D'ACHAT)
PRODUCT
PRODUIT
Projection TV In-Home Service
Colour TV In-Home (25" and above)
D-ILA Rear Projection In-Home Service
LCD TV In-Home Service (25" and above)
Ecrans de projection Service a Domicile
Ecrans de TV Couleur Service a Domicile (25" et plus)
~V projection arriere D-ILA Service a Domicile
Ecrans de LCD Service a Domicile (25" et plus)
PARTS (Years)
Labour (Years)
PIECES (annees) MAIN-D'OEUVER (annees)1
1
1
j
2
2
90 DAYS
90 DAYS
90 JOURS
90JOURS
Wood Cone Speakers
Enceinte a Cone en Bois
5
5
All Other Categories
Toutes les autres categories
1
1
AC Adapters, Remote Controls, Headphones, Microphones and
Projector Lamps
Adaptateurs AC, Telecommande, Casque D'ecoute, Microphones
et Lampe de Projecteur
(I) Tout dommage cause par le feu , une
inondation, un eclair, une surtension ou tout
autre evenement hors du controle de JVC.
(m) POUR LES PRODUITS D'AUTOMOBILE
La garantie ne couvre pas !'elimination
d'interferences statiques ou electriques de
Ia voiture, le nettoyage de tete, les
ajustements et les coOts de main d 'ceuvre
associes
l'enlevement ou
Ia
reinstallation de !'unite pour reparation.
3. Standards:
If any defects should be found in a JVC product
within the applicable terms, necessary repairs
shall be made at no cost to the purchaser for
parts or labour when JVC acknowledges that
such defects are due to faulty material or workmanship.
3 . Criteres:
Si un produit JVC s'averait defectueux, seton les
conditions
applicables,
les
reparations
necessaires seront effectues sans coOts
additionnels
l'acheteur pour les pieces et Ia
main d'ceuvre lorsque JVC reconnait que de telles
defectuosites son! causees par une defectuosite
de materiel ou de fabrication.
4. Exclusion of All Other Express Warranties:
This warranty constitutes the entire express
warranty given by JVC for JVC products and
no dealer or service centre personnel or his,
its or their agent or employee is, or are authorized to extend or enlarge this warranty on behalf of JVC.
4 . Exclusion de toutes autres garanties expresses:
Celie garantie constitue l'entiere garantie express
donnee par JVC pour les produits JVC. Nul
representant ou employe d'un detaillant ou d'un
service d'entretien n'est autorise prolonger cette
garantie au nom de JVC.
5. Disclaimer of Consequent ial Damage:
5 . Denegation des dommages indirects :
Dans Ia mesure penmise par Ia loi, JVC nie toute
responsabilite pour perle de temps ou d'usage de
ses produits, des coOts de transport ou tout autre
dommage ou inconvenient indirect, accidentel et
consequent.
a
a
a
a
1
* In-home service to be provided where available
Where it is not available, the Purchaser must assume the responsibility and expense for the proper
packing, shipment and all costs associated with the delivery of the equipment to and from the closest
JVC Authorized Service Centre.
*Service a domicile fourni par un detaillant disponible.
S'il n'y a pas de service JVC disponible a proximite, l'acheteur doit assumer Ia responsabilite et les
coOts pour un emballage adequat, !'expedition, ainsi que tous les coOts associes a Ia livraison de
l'equipement chez et depuis le detaillant JVC autorise le plus pres pour un service d'entretien.
Receivers and Home Speakers purchased separately, Front
Projection and Car Audio "ARSENAL" Series
Recepteurs et Hauts-Parleurs achetes separement, Projecteur
Avant et Audio d'Auto de Serie " ARSENAL "
(I ) Any defects caused by fire, flood, lightning,
power surge, or other events beyond the
control of JVC.
(m) FOR AUTO PRODUCTS
Warranty does not cover elimination of car
static or electrical interferences, cleaning
of head, adjustments, or labour cost for the
removal or reinstallation of the unit for
repair.
I
To the extent the law permits JVC disclaims
any responsibility for loss of time or use of its
product, transportation costs, or any other
indirect, incidental or consequential damage or
inconvenience.
JVC CANADA INC.
Service toll free # : 1-800-964-2650
E-mail :service@jvc.c a
TO OUR VALUED CUSTOMER-THANK YOU FOR PURCHASING THIS JVC PRODUCT.
WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.
NEED HELP ON HOW TO HOOK UP?
NEED ASSISTANCE ON HOW TO OPERATE?
NEED TO LOCATE A JVC SERVICE CENTER?
LIKE TO PURCHASE ACCESSORIES?
JVC IS HERE TO HELP!
TOLL FREE: 1(800)252-5722
http://www.jvc.com
Remember to retain your Bill of Sale for Warranty Service.
Do not attempt to service the product yourself
Caution
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
PRODUCT REGISTRATION
We suggest that you register your product since it will enable us
to contact you directly if it is ever necessary to correct a safety related
condition in your product.
You can register at www.register.jvc.com
Please note that failure to register does not diminish any of your rights
during the warranty period.
BT-51018-7
(0812)
Printed in Indonesia
***************************************** *************************************
*
i! JVC
LIMITED WARRANTY
IONLY FOR PRODUCT PURCHASED IN U.S.A.!
1-1
i*
I USA ONLY I
!
* JVC Americas Corp. (JVC) warrants this product and all parts thereof, except as set forth below ONLY TO THE *
! ORIGINAL RETAIL PURCHASER to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of !
* original purchase for the period shown below. ("The Warranty Period")
*
*
I PARTS
!
*
*!*
1
I LABOR
YR
*
1
!
YR
*
*!*
*THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND *
IN THE COMMONWEALTH OF PUERTO RICO.
!
!
*
!
*
*
!
WHAT WE WILL DO:
If this product is found to be defective within the warranty period, JVC will repair or replace defective parts with new or
rebuilt equivalents at no charge to the original owner. Such repair and replacement services shall be rendered by JVC
during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the
remainder of the Warranty Period. All products may be brought to a JVC authorized service center on a carry-in basis.
Color televisions with a screen size of 37"class or greater qualify for in-home service. In such cases, a technician will
come to your home and either repair the TV there or remove and return it if it cannot be repaired in your home.
::WHAT YOU MUST DO FOR WARRANTY SERVICE:
Please do not return your product to the retailer
Instead, return your product to the JVC authorized service center nearest you. If shipping the product to the service
* center, please be sure to package it carefully, preferably in the original packaging, and include a brief description of
the problem(s). Please call 1-800-252-5722 to locate the nearest JVC authorized service center. Service locations
* can also be obtained from our website http://www.jvc.com. If your product qualifies for in-home service, the service
* representative will require clear access to the product.
*
!
!
*
** WHAT IS NOT COVERED:
!
:Z
*
*
!
*
!
::
*
:Z
*
:Z
*
*
*
**
:Z If you have any questions concerning your JVC Product, please contact our Customer Care Center at 800-252-5722 !
! This limited warranty provided by JVC does not cover:
!
*
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty*
!
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by:Z
*
JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial *
*
number has been altered, tampered with, defaced or removed;
*
!
2. Initial installation, installation and removal from cabinets or mounting systems.
:Z
*
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning; *
!
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
!
*
5. Signal reception problems and failures due to line power surge;
*
6. User Rem~>Val Memory DevicesNideo Pick-up Tubes/CCD Image Sensors are covered for 90 days from the date of purchase;!
*
7. Accessones;
*
*
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
*
:Z 9. Products used for commercial purposes, including, but not limited to rental.
!
* 10. Loss of data resultant from malfunction of hard drive or other data storage device;
*
!
*
*
:Z There are no express warranties except as listed above.
:Z
::THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS !
* LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
*
*
* JVC SHALL NOT BE LIABLE FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE, OR ANY OTHER
::DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION,
*DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
* OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
::WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE
:: WARRANTY PERIOD SET FORTH ABOVE.
*
*
!
*
*
!
!
:Z Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an !
* implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific *
:Z legal rights and you may also have other rights which vary from state to state.
!
*
*
!
*
JVC AMERICAS CORP.
1700 Valley Road, Wayn~, New Jersey 07470
http://www.Jvc.com
*
:Z
*
****************************************** **************************************
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAIL
OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY
INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet.
Retain this information for future reference.
Model No.:
Serial No.:
Purchase date :
Name of dealer :