BWC600SS 60 cm 46
Bottle dual
temperature wine
cooler
User manual for your Baumatic
BWC600SS
60 cm 46 Bottle dual
temperature wine cooler
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference, for
you or any person not familiar with the operation of the appliance.
GS 19/11/10
2
Contents
Environmental note
4
Important safety information
5–6
Specifications of your wine cooler
Specifications
Dimensions
Description of the appliance
Control panel
Description of the product features
7-10
7
7
8
9
9-10
Using your Baumatic wine cooler
Before switching on
During first use
Switching on the appliance and setting the temperature
Changing between Fahrenheit and Celsius
The humidity control box
Loading the wine cooler
10-16
10
10-11
11-12
12
12
12-13
Storing your wines
Wine storage problems
13-15
15-16
Cleaning and maintenance
Defrosting
Removing the shelves for cleaning
Moving your wine cooler
Power failure
Vacation time
16-18
16-17
17
17
18
18
Installation
Electrical connection
Positioning
Built-in installation
Installing the handle
Reversing the door of your wine cooler
18-24
19
20
21
22
22-24
Troubleshooting
24-25
Contact details
26
3
Environmental note
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Advice Line.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
Use of the appliance
o Your appliance is only designed to be used in the
home. It is suitable for storing and chilling wine.
NO food stuffs must be stored in the appliance. If it
is used for any other purpose or it is not used
correctly, then Baumatic Ltd. will accept no liability
for any damage that is caused.
o Altering the specification of the appliance must not be attempted
for reasons of safety.
Before using your appliance
o Check the appliance for any signs of transport damage. If you
notice any damage, then you should not connect your appliance
to your mains supply and should contact your retailer.
Refrigerant
o Your appliance contains R600a refrigerant, which is a natural gas
that does not contain CFCs that can damage the environment.
However it is a flammable substance, therefore care should be
taken:
ƒ During the transportation and installation of the
appliance, make sure that the refrigeration pipework
does not get damaged.
ƒ If it does become damaged then sources of ignition
and open flames should be avoided. Also the room
that the appliance is situated in should be thoroughly
ventilated.
o Do not place any objects on top of the appliance,
as this may damage the table top.
5
Child safety
o Packaging material should be kept away from
children.
o Children should not be allowed to touch the
controls or play with the appliance.
General safety
o Do not pull on the power supply cable to remove the plug from
your mains supply socket.
o Do not pull out or insert the plug with wet hands.
o Do not attempt to use your appliance outdoors or
any place where it is likely to come into contact
with the elements.
o Before cleaning the appliance or performing
maintenance work, ensure that the appliance
disconnected from your mains supply.
has
been
o Never allow the back coils of the appliance to come into contact
with the wall surface.
o Always ensure that the location where you are installing your
appliance is free of stored items such as papers and other
flammable materials.
o Never block the ventilation openings of the appliance, either on
the inside or its exterior.
o It is vital to keep your appliance well ventilated,
so that there is proper air flow between the
bottom of the unit and the plinth/kick plate
which it is sitting on.
o Do not place electrical devices inside of the appliance, such as
mixers or ice cream makers.
Service
You should not attempt to repair the appliance
yourself, as this could cause injury or a more serious
malfunction. If you require a service call then please
contact the Customer Care Department.
6
Specifications of your wine cooler
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
Gross capacity: 145 litres
Net capacity:
138 litres
Bottle capacity: 46 x 0.75 litre Bordeaux style wine bottles
Electronic push button control operation
LED display
Celsius and Fahrenheit button
6 Adjustable wooden shelves
Adjustable temperature
Digital thermometer
Humidity control box
Internal light
Black exterior
Stainless steel door frame and handle
Reversible door
Adjustable feet
Tempered door glass
Designed to store wine at its optimum temperature between +
5°C - 22°C
Dimensions of appliance**
Height:
Width:
Depth:
865 - 890 mm
595 mm
570 mm
** Please refer to the installation instructions for more specific
information on the size of aperture that you will require.
IMPORTANT: When you install your appliance it is important to bear
in mind its climatic rating.
In order to find out the climatic rating of your appliance, you should
check the rating plate. The rating plate is located on the front left edge
of appliance. The rating plate will indicate the ambient temperature
range that your appliance will function correctly within.
Model number ………………………………………………
Serial number
………………………………………………
Date of purchase
……………………………………………..
7
Description of the appliance
1)
2)
3)
4)
5)
Stainless steel door
Stainless steel handle
Digital control panel
Adjustable shelves
Adjustable foot
8
Control panel
The control panel is located in the middle of the appliance.
1)
2)
3)
4)
5)
6)
Light control button
Temperature control button
Upper zone display
Lower zone display
Temperature plus button
Temperature minus button
This icon indicates that the control panel is for the upper cooling
zone.
This icon indicates that the control panel is for the lower cooling
zone.
Description of the product features
1) Control panel
o The control panel is located in the middle of the appliance,
behind the glass door. This means it is easy to set the
temperature of the appliance and see what temperature the
appliance is set to.
2) Two cooling zones
o There are two cooling zones inside of your wine cooler; they are
separated by a partition that holds the control panel.
o Each cooling zone has an independent temperature control and
temperature display.
9
3) Interior light
o The wine cooler has an interior light. The light can be switched
on and off by using the light control button (1).
4) The wine cooler shelves
o The wooden shelves are fully adjustable to suit various wine
bottle shapes and sizes.
o To prevent damaging the door gasket, make sure the door is
fully open when pulling shelves out of the rail compartment.
o For easy access to the bottles stored, pull the shelves out
approximately 1/3.
Using your Baumatic wine cooler
Before switching on
o Make sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
o After delivery, wait for eight hours before connecting the
appliance to your mains supply. This will allow any refrigerant
gasses that may have been disturbed during the transportation
process to settle.
o The outside of the appliance and the removable accessories
contained within it, should be cleaned with a solution of liquid
detergent and water.
o The interior of the appliance should be cleaned
with a solution of sodium bicarbonate dissolved in
lukewarm water. The interior and accessories
should be thoroughly dried, after the cleaning
process has been completed.
o There can be an odour when you first switch on the appliance. It
will lessen as the appliance starts to cool.
During first use
IMPORTANT: When you use the wine cooler for the first time or
restart the appliance after it has been turned off for a long
time, there could be a few degrees variance between the
temperature you select and the one indicated on the LED
display. This is normal and it is due to the length of activation
10
time. Once the wine cooler has been running for a few hours
everything will be back to normal.
o When you first switch on the appliance, the compressor will run
continuously until the wine cooler reaches a cool enough
temperature.
o During this period of time, you should try not to open the door
frequently or place bottles inside of the appliance.
o If the unit is switched off or unplugged, you must allow at least 5
minutes before restarting the appliance or reconnecting it to
your mains supply.
Switching on the appliance and setting the temperature
o To switch the appliance on, press the light control button (1)
and the temperature control button (2) simultaneously for 5
seconds.
o The temperature for each zone will need to be set individually.
The temperature settings for both zones are adjustable within
the range of 5°C - 22°C / 40°F - 71°F.
o The temperature set for the lower zone must always be
the same or higher than that in the upper zone.
o When you press the temperature control button (2) for the first
time, the LED display will show the factory default temperature
setting of 12°C / 54°F for both zones.
o Press the temperature control button (2) again and the left LED
indicator for the upper zone will flash. Use the plus (5) and
minus (6) buttons to set the desired temperature for the upper
zone.
o Press the temperature control button (2) yet again and the right
LED indicator for the lower zone will flash. Use the plus (5) and
minus (6) buttons to set the desired temperature for the lower
zone.
o The temperature will increase by 1°C or 1°F if you touch the plus
button once and will decrease by the same amount of you press
the minus button once.
o When you set a new temperature for either of the zones, the
display will show this temperature for 5 minutes before showing
the actual zone temperature. During this time, the zone
temperature will adjust accordingly.
11
o To view the set temperature in both zones at any time, press the
plus or minus button. The display will flash the temperature for 5
seconds.
IMPORTANT: When the temperature of a zone is changed, the
compressor works harder to reach the required temperature.
During this time, the side panels of the wine cooler can reach
up to 45°C however they will cool down when the set
temperature is reached.
Changing between Fahrenheit and Celsius
o You can select whether the temperature displays show Celsius or
Fahrenheit.
o To alter what the temperature displays are showing, press the
plus (5) and minus (6) buttons at the same time for 5 seconds.
o You cannot change the display if you are in the process of
adjusting the temperature of a cooling zone.
The humidity control box (optional)
The wine cooler is equipped with a system for maintaining the correct
level of humidity for wine storage.
o Fill the small plastic reservoir (humidity box) ¾ full with water
and replace. The humidity box is located on the top shelf
and secured by runners.
o Check the water level regularly and refill as necessary.
o IMPORTANT: Please ensure the reservoir is positioned
correctly on the runners to avoid the possibility of water
spillage.
Loading the wine cooler
o IMPORTANT: Your appliance is ideally suited to store
0.75 litre Bordeaux style wine bottles. Whilst it can
store larger bottles, you must make sure that they do
not prevent the door from shutting properly.
o Always check that you can close the door without it fouling
on a wine bottle, before shutting it.
o When loading several bottles of wine at once, it will take
longer for the appliance to cool the individual bottles.
12
o As many bottles may differ in size and dimensions, the
actual number of bottles you are able to store may vary.
The maximum storage number is based on standard 0.75
litre Bordeaux style wine bottles.
o You can place 16 standard bottles in the upper zone with 8
bottles on each shelf.
o You can store 30 standard bottles in the lower zone with 8
bottles on each full size shelf and 6 bottles on each half
size shelf.
Storing your wines
The chart below indicates the ideal storage temperatures for different
types of wine:Type of wine
Red wine (*)
White wine (**)
Sparkling
wines/champagne
Rose wine
Vintage wine
Temperature
(Celsius)
15.5 – 18.5°C
10 - 15°C
7.2 – 9.5°C
Temperature
(Fahrenheit)
59.9 – 65.3°F
50 – 59°F
45 – 49.1°F
9.5 – 10.5°C
13°C
49.1 – 50.9°F
55°F
* Light red wines, such as Beaujolais, Pinot Noir and Cabernet Franc
benefit from being served slightly cooler than full-bodied reds.
13
** Chardonnay is often served too cold. You should chill it at a warmer
temperature inside of your wine cooler. Or leave it to warm slightly
when you remove it from your wine cooler.
o Temperature stability is the most important factor when it comes
to storing wine.
o Exposure to light, vibrations or fluctuations in temperature and
humidity can all cause wine to spoil. When properly stored,
wines not only maintain their quality but many will actually
improve in aroma, flavour and complexity as they mature.
o Wines kept at a higher temperature will age faster. Wine that is
exposed to temperatures that are greater than 21°C (70°F) will
suffer from poorer flavour and aroma.
o If wine is kept at too low a temperature, this can result in the
development of harmful deposits. A humidity of 70% is ideal for
keeping corks from shrinking.
o After a bottle of wine has been opened, the wine comes into
contact with air. So it is best to store the remainder of the bottle
upright, to minimize the surface area of the wine that is coming
into contact with the air.
o Once opened, wine will remain in a drinkable condition for two
days for delicate whites or three days for rich reds, as long as
the bottle as been resealed. You should make sure that the seal
is firm by checking the stopper.
o Special stoppers that keep wine sparking and Champagne
bubbling for one or two days after opening, can be bought at
most good wine shops.
o When stored correctly, white wines can keep well for up to two
years. Full bodied reds will age well for ten years and dessert
wines will age well for up to twenty years.
o When you buy a bottle of wine, you should transfer it to a
suitable storage location immediately (if you are not going to
store it in your wine cooler).
o Cheaper bottles of wine will not age as well as more expensive
ones.
o To make the most of the bouquet and taste of your wine, never
fill more than half a glass at a time. It will also help if the shape
of your wine glass is appropriate for your wine. The size and
shape of your wine glass’s bowl will determine the intensity and
14
complexity of the bouquet. The stem should be long enough to
allow you to avoid hand contact with the bowl of the glass and
should be tulip-shaped or tapered at the top.
Wine storage problems
Corking- a tiny percentage of bottled wine (about 1%) will suffer from
this. The cork reacts with the wine and gives it a musty, unpleasant
taste. It is the most common wine storage problem and is caused by
harmless bacteria growing on the cork. As unfortunate as this is, there
is nothing to do but to discard all of the wine in the affected bottle.
This is not to be confused with small fragments of cork floating in the
wine itself, which will not impair the flavour.
Oxidisation- when wine has been opened and left for longer than a
day; it tends to lose its aroma and colour, giving an overall flat taste.
The only way to avoid this, it to either drink the wine on the same day
it was opened or to use a vacuum device specially designed for
removing oxygen from opened wine bottles. If you use such a device,
the wine should still be consumed shortly afterwards.
Ullage- this is loss of wine from the bottle by evaporation or leakage.
Signs of ullage include wine seeping around the cork, a protruding cork
or a stained label. It can happen if the bottle has been allowed to get
too warm. The wine may still be drinkable, if the leakage was recent;
however, you should be aware that if the wine cools down again,
contraction can cause more air to be sucked into the bottle and result
in further deterioration.
Slight effervescence in still wine- this isn’t really a problem with
the way the wine has been stored, but as a result of incomplete
malolactic fermentation before the wine was bottled. A good way to
get rid of the effervescence is to let the wine breathe. Alternatively
you can use a bottle vacuum device, after about five minutes the
effervescence will vanish.
Sediment- this is not normally a problem, however both red and
white wines can produce sediment after a number of months in a
bottle. The sediment consists of tartrate crystals and is totally
harmless. If anything the building of sediment can be considered a
good sign because it means that the wine was not subjected to much
(if any) filtering, meaning that the flavours and aromas should be
preserved better.
A good way to get around sediment (if it is a problem) is to stand the
bottle upright, the day before opening, so that the sediment can settle
to the bottom of the bottle.
15
You can also decant your wine; decanting will “open up” the flavour of
both young and old wines, but younger wines in particular. To decant,
pour the wine slowly and evenly into your decanter.
Cleaning and maintenance
WARNING: PLEASE ENSURE THAT YOUR
APPLIANCE IS DISCONNECTED FROM
YOUR
MAINS
SUPPLY
BEFORE
ATTEMPTING TO CLEAN IT.
o Do not clean the appliance by pouring water onto
it or spraying water over it.
o The interior of the wine cooler should be cleaned
periodically, using a solution of bicarbonate of soda
and lukewarm water.
o Clean the accessories separately with soap and water.
Do not clean them in a dishwasher.
o Do not use abrasive products, detergents or soaps.
o After washing the appliance, wipe over the area
that you have cleaned with a damp cloth and then
dry it thoroughly.
o When cleaning is complete, dry your hands and then reconnect
the plug to your mains supply.
Defrosting
o Defrosting occurs automatically inside of the wine cooler during
operation. The defrost water is collected by the evaporating tray
and evaporates automatically.
o The evaporating tray and defrost water drain hole should be
cleaned periodically. This will prevent water from collecting in
the bottom of the wine cooler, instead of flowing down the
defrost drainage channel and drain hole.
16
o You can also pour a small amount of water down the drain hole
to clean inside of it.
o You should be careful to make sure that wine bottles do not
touch the rear wall of the appliance, as this can interrupt the
automatic defrosting process and deflect water into the base of
your wine cooler.
Removing the shelves for cleaning
o To remove any of the shelves from the rail compartment, move
the shelf to the position where the notch of wooden shelf is
exactly under the plastic post and lift the wooden shelf. Please
ensure these are replaced when the shelf is put back.
o Make sure the shelves are fully engaged before loading any
bottle into the cooler. Pull the shelves out all the way to the
STOP position and push them back in several times to make sure
the shelves are properly engaged.
Moving your wine cooler
If you need to move your wine cooler to another location you should
follow the steps outlined below.
o Remove all items from the wine cooler.
o Securely tape down all loose items such as the shelves inside the
appliance.
o Turn the adjustable foot up to the base to avoid damage.
o Tape the door closed.
o Be sure the appliance stays secure in the upright position during
transportation. Also protect the outside of the appliance with a
blanket or similar item.
17
Power failure
o Most power failures are corrected within a few hours and should
not affect the temperature of your appliance if you minimize the
number of times the door is opened.
o If the power is going to be off for a longer period of time, you
need to take the proper steps to protect the contents.
IMPORTANT: If the appliance is unplugged, the power is lost or
turned off you must wait 3 to 5 minutes before restarting the
wine cooler. If you attempt to restart before this time delay,
the wine cooler will not turn on.
Vacation time
Short holidays: Leave the wine cooler in operation for holidays of less
than three weeks.
Long absences: If the appliance will not be used for several months,
remove all items, turn off the appliance and unplug the electricity
cable. Clean and dry the interior thoroughly. To prevent odour and
mould growth, leave the door open slightly by blocking it open if
necessary.
Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found on the front left edge of the
inside of the wine cooler.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
18
Electrical connection
YOUR WINE COOLER IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations.
o Your wine cooler comes supplied with a 13 amp plug fitted. If in
future you need to change the fuse in this plug, then a 13 amp
ASTA approved (BS 1362) fuse must be used.
o The wiring in the mains lead is coloured as follows:
Brown
Blue
Green and yellow
Live
Neutral
Earth
o As the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:
The brown wire must be connected to the terminal marked “L”
(live), or coloured red.
The blue wire must be connected to the terminal marked “N”
(neutral), or coloured black.
The green and yellow wire must be connected to the terminal
marked “E” (earth), or by the earth symbol, or coloured green
and yellow.
o When the connection is completed, no stray strands or cut wire
should be present. The cord clamp must be secured over the
outer sheath.
19
Positioning
o It is advisable that your appliance is only installed in a location
where the ambient temperature of the room, corresponds with
the climate classification that is stated on the rating plate of your
appliance. Your appliance may not function correctly if the
ambient temperature falls outside of the following ranges.
Climate classification
SN
N
ST
T
Appropriate ambient temperature
+10 to +32 degrees centigrade
+16 to +32 degrees centigrade
+18 to +38 degrees centigrade
+18 to +43 degrees centigrade
o Positioning the appliance requires two people in order to avoid
injuries or damage to the appliance.
o Your appliance should not be located in direct sunlight or
exposed to continuous heat or extremes of temperature (e.g.
next to a radiator or boiler). If this is not feasible, then you
should install an insulation plate between the appliance and the
adjacent heat source.
o You should check whether there is an electrical socket available,
which will be accessible after your appliance is installed.
o Place the appliance flatly and firmly on a solid base. The
appliance is fitted with adjustable feet on the front side, which
can be used to level the appliance.
o When the wine cooler is being used as a freestanding unit,
anything positioned above the appliance must be at least 10 cm
away to allow sufficient cooling of the condenser. You must allow
a 5 cm gap to the rear and either side of the appliance.
o Be sure to leave enough space for the opening of the door, to
avoid damage to the appliance or personal injury.
o IMPORTANT: The vent at the base of the appliance is for
ventilation. Nothing should be placed in front of this vent;
otherwise your wine cooler may not operate properly.
20
Built-in installation
o Your wine cooler can be used as a freestanding or a built in unit.
If you are going to use it as a built in unit, then the dimensions
shown in the diagram above will need to be followed.
o In particular the depth dimension must be observed.
o IMPORTANT: The vent at the base of the appliance is for
ventilation. Nothing should be placed in front of this vent;
otherwise your wine cooler may not operate properly.
o A decorative plinth can be fitted to the front of the base vent as
long as the cut out shown in the diagram on the next page is
made in the plinth. This cut out is required whether the vent is
removed or not.
21
Installing the handle
o Remove the door gasket on the side you wish to install the
handle. You can see two designated holes for handle installation.
o Install the handle tightly as shown in the diagram above with the
two screws, lock washers and flat washers provided.
o Replace the door gasket.
Reversing the door of your wine cooler
This appliance has the capability of the door opening from either the
left or right hand side.
Any parts that you remove from the appliance whilst
reversing the door, should be retained for later use.
o Open the glass door and remove
the two screws, under the right
bottom corner of the glass door,
that are used to hold the right
lower hinge to the door shaft
assembly.
o Be careful to support the glass
door with both hands to prevent it
dropping
after
removing
the
screws.
22
o Pull down to remove the glass door
and place it on a padded surface to
prevent scratching it.
o Remove the right top hinge and
right lower hinge.
o Take the left top hinge and left
lower hinge from the plastic bag
that contained this manual then
install them in the designated
positions on the left side of the
cabinet.
o Turn the glass door around 180°
and reinstall it.
IMPORTANT: Check that the door opens and shuts correctly,
without fouling, after you have completed the door reversal
process.
After the door has been reversed, you should check
the door seal of the wine cooler. The seal should not
23
be creased or crushed; otherwise there will be a gap between it
and the inside of the door.
o The seal must adhere properly all the way around the door.
o If the seal is not adhering to the cabinet properly, then you
should either:a) Use a warm damp cloth and manipulate the seal until it does
adhere to the cabinet properly, all the way around the door.
or
b) Use a hair dryer on its lowest heat setting and lightly heat the
areas of the door seal that are not adhering correctly. The heat
will make the seal more pliable and this will allow you to
manipulate the seal into the correct position.
IMPORTANT: DO NOT HEAT THE DOOR SEAL ON ANYTHING BUT
THE LOWEST HEAT SETTING, OR HEAT THE SEAL FOR A LONG
PERIOD OF TIME. OTHERWISE DAMAGE MAY BE CAUSED TO
THE DOOR SEAL, WHICH WOULD NOT BE RECTIFIED UNDER
THE GUARANTEE FREE OF CHARGE.
IMPORTANT: WHEN YOU HAVE REVERSED THE DOOR OF THE
APPLIANCE, IF YOU HAVE PLACED THE APPLIANCE ON ITS
BACK, YOU MUST WAIT FOR 8 HOURS BEFORE SWITCHING THE
APPLIANCE BACK ON.
Troubleshooting
IMPORTANT: If your wine cooler appears not to be
operating properly, before contacting the Customer
Care Department, please refer to the checklist
below.
PROBLEM
Appliance does not operate
Temperature inside the appliance is too
warm.
POSSIBLE CAUSE
Not plugged in.
The circuit breaker has tripped or the
fuse has blown.
The temperature controls are set too
warm. Set the temperature controls to a
cooler setting and allow several hours for
the temperature to stabilise.
The door is being kept open too long or is
being opened too frequently, which is
allowing warm air to enter the appliance.
The door is not closed completely.
The door gasket is not sealing correctly.
The
appliance
has
recently
been
disconnected from the mains supply; it
24
Temperature inside the appliance is too
cold
Vibration
Moisture is forming on the inside of the
appliance.
Moisture is forming on the outside of the
appliance.
will take at least four hours for it to get
down to temperature again.
The temperature controls are set too
cold. Set the temperature controls to a
warmer setting and allow several hours
for the temperature to stabilise.
Check to ensure that the appliance is on
a level surface.
The appliance is touching the back wall
behind it. Reposition the appliance and
move it from the wall.
If vibration continues to occur, then turn
off the appliance and unplug it from your
mains supply. Then contact the Customer
Care Department for assistance.
The door is slightly open.
The door is being kept open too long or is
being opened too frequently. Open the
door less often.
The door is not sealed properly.
The door is slightly open, causing cold air
from inside the appliance to meet warm,
moist air from the outside.
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact the
Customer Care Department on telephone number
(0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
25
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Czech Republic
Baumatic CR spol s.r.o.
Průmyslová zóna Sever 696
460 11 Liberec 11
Czech Republic
+420 483 577 200
www.baumatic.cz
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
Slovakia
Baumatic Slovakia, s.r.o.
Galvániho 7/D
Slovakia
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
+49 5221 694 99-0
+421 255 640 618
Germany
Baumatic Gmbh
Lilienthalstrasse 1
320 52 Herford
Deutschland
www.baumatic.de
Website:
www.baumatic.co.uk
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
Republic of Ireland
+3904 9920 2297
Service Telephone
1-890 812 724
www.baumatic.it
Spares Telephone
091 756 771
Holland
Baumatic Benelux B.V.
Grindzuigerstraat 22
1333 MS ALMERE
Nederland
+3136 549 1555
www.baumatic.nl
26
27