advertisement
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v3.7.0 (2014/9/09)
Modules:
Device Pack v 3.7.0
Supported Systems:
Mainconsole v 4.1.12 and above*
NVRmini 2 v 1.7.1 and above**
NVRsolo
Titan NVR
NUUO Crystal™ v 1.6.2 and above v 2.0.3 and above
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
**For NVRmini 2 and NVRsolo multi stream setting function, please upgrade to NVRmini 2/NVRsolo v2.0.0 and above first.
New Camera Supported:
ACTi E97
Arecont Vision
Axis
AV12186DN
M1025, P3384
Bosch
Brickcom
D-Link
Fine
LG
Lilin
VIP X16 XF E
PH-100ah, VS-04A v2
DCS-2310LB1, DCS-6116, DCS-6915B1
ACM-V3002, ACM-R3002, ACM-PT500, CDV-3F828, CDV-5VM501Z3,
TCP-VM559Z3
LND7210, LND7210R, LNV7210, LNV7210R, LNU7210R
IPD2322, LD2222
FW upgrade:
D-Link
Fine
Sony
Vitek
DCS-3010(FW: v1.12.07)
EP-Q2036HW-IP(FW: V1.0.46)
SNC-CH160 (FW 1.82), SNC-DH110 (FW 1.82),
SNC-DH220 (FW1.82), SNC-RH124 (FW 1.84)
VT-20VN-M(FW: v4.24-B3), VTC-IR402(FW: v4.24-B3)
1 / 142
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 1
NVR Device Pack Release Note
NUUO version 3.7.0
Zavio B8210( FW: M201.0_M2.8.8)
Multiple Stream Setting Supported:
Sony SNC-ER580, SNC-CH160, SNC-DH110, SNC-DH220
Notice:
1. ACTi a. E97 i. ii. iii.
The actual framerate may not reach the setting value under high resolution and quality configuration. (Camera performance limitation)
The 2 nd stream’s actual bitrate is higher than settings.(Camera firmware issue)
The function “send mail by event” might fail to attach snapshot under high resolution
(NUUO server limitation) iv. The motion signal would not stop when disabling motion event if the motion has been triggered. (NUUO server limitation)
2. Bosch (Mainconsole IP+) a. VIP X16 XF E i. ii. iii.
Only support G.711 audio codec. (Camera performance limitation)
Snapshot resolution is not correspond to existing profile. (Camera firmware issue)
Multi stream setting might fail due to the limitation of inter-streaming dependency.
(NUUO Server limitation)
3. BrainChild a. CAM-335E i. Camera is unable to achieve maximum FPS under main or 2 nd stream with high bitrate. ii. iii. iv. v. vi.
(Camera performance limitation)
High resolution and bitrate would cause stream latency. (Camera performance limitation)
After setting camera parameters , NUUO server cannot get video parameters and connect camera immediately (Camera performance limitation)
If setting video and audio at the same time, the changed configuration wouldn’t apply to stream (Camera firmware issue)
MJPEG quality value on camera web is different from the value NUUO server display
(Camera firmware issue)
Motion detection does not work when main stream’s format is MJPEG (Camera Issue)
2 / 142
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 2
NVR Device Pack Release Note
NUUO version 3.7.0
4. Dlink a. DCS-6116 i. ii.
Some resolution are not synchronized with camera web. (Camera firmware issue)
Cannot setup from 13fps to 25fps. (Camera firmware issue) iii. Cannot setup resolution under 720x480. (Camera firmware issue) b. DCS-3010 i. Stream would disconnect and motion would not be triggered due to camera limited performance. (Camera firmware issue) c. DCS-2310LB1 i. Control mode of resolution, framerate, bitrate cannot be changed under H.264 format. ii.
(Camera firmware issue).
The name of this camera in search window will show as DCS-2310L. (Camera firmware issue)
5. Fine a. ACM-PT500 i. Camera is unable to achieve maximum FPS. (Camera performance limitation) b. CDV-3F828 i. Camera is unable to achieve maximum FPS. (Camera performance limitation) c. ACM-V3002 i.
6. Lilin
Both camera web and NUUO server have audio noise issue. (Camera firmware issue) a. IPD2322 i. Due to Onvif restriction, some frame rate and bit rates cannot be set. (ONVIF ii. limitation)
Due to Onvif restriction, dependency between framerate and bitrate cannot be iii. showed. (ONVIF limitation)
Audio G.711 mu-law in with 16/32/44.1 KHz sampling rate is not supported. (NUUO server limitation)
Camera may respond and show invalid value from current setting. (Camera firmware iv. issue) b. LD2222 i. Due to Onvif restriction, some frame rate and bit rates cannot be set. (ONVIF limitation) ii. iii.
Due to Onvif restriction, dependency between framerate and bitrate cannot be showed. (ONVIF limitation)
Audio G.711 mu-law in with 16/32/44.1 KHz sampling rate is not supported. (NUUO server limitation)
3 / 142
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 3
NVR Device Pack Release Note
NUUO version 3.7.0
7. Vitek a. VT-20VM-M i. The function that send snapshot to FTP is only supported by MJPEG format. (Camera firmware issue) ii. iii.
Only support rtsp port 554.(Camera firmware issue)
The actual framerate may not reach the setting value under high resolution and iv. v. quality configuration.(Camera performance limitation)
Brightness, contrast and saturation are not supported.(Camera firmware issue)
UPnP search are not supported.(Camera firmware issue) b. VTC-IR402 i. The function that send snapshot to FTP is only supported by MJPEG format. (Camera firmware issue) ii. iii. iv. v. vi.
8. Zavio
Only support rtsp port 554.(Camera firmware issue)
The actual framerate may not reach the setting value under high resolution and quality configuration.(Camera performance limitation)
Brightness, contrast and saturation are not supported. (Camera firmware issue)
The talk function is invalid.(Camera firmware issue)
UPnP search are not supported.(Camera firmware issue) a. B8210 i. Resolution 1920x1080 and 1280x720 cannot be set because 2 nd stream (Low) ii. resolution list is not synchronized with camera web. (Camera performance limitation)
Multi-stream setting for 2 nd stream is limited by 3 rd stream's video parameter. If resolution for 3 rd stream is higher than 640x480, 2 nd stream video parameter setting would be failed. (Camera firmware issue)
9. Brickcom a. ph-100Ah i. ii.
Audio function is not supported.
Resolution and bitrate list is not synchronized with the camera webpage. iii. The video does not play smoothly when the frame rate set to 1. b. VS-04A i. ii.
PTZ doesn’t work
Audio doesn’t work iii.
10. Sony
Resolution and bitrate list is not synchronized with the camera web. a. SNC-RH124
4 / 142
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 4
NVR Device Pack Release Note
NUUO version 3.7.0 i. ii. iii.
When camera’s format is MJPEG and resolution is larger than 640x480, the connection is unstable.
The camera is unable to achieve 30fps with MJPEG format.
Camera must reconnect when change the audio codec in web site. b. SNC-CH160 i. Camera is unable to achieve 30 fps with resolution 1280x1024. c. SNC-DH110 i. It would take 30~50 seconds to reconnect after changing video format.
Bug Fixed the bug thated:
[MainConsole]
1. [Sunell] – Fixed the bug that the motion issue of Sunell generic models in the multiple network interface controller.
2. [ONVIF] - Fixed the bug that getting video parameter fail when Profile do not contain any
VideoEncoderConfiguration
3. [Hikvision Generic] - Disable the option of "Enable Talk" when the audio is turned off
4. [Zavio F3210/F1100] - Fixed the bug that camera would crash when connecting
5. [Hikvision DS-2CD7253F-EIZ] - Fixed the bug that camera’s zoom and focus function doesn’t work.
6. [Zavio] - Fixed camera unstable connection.
7. [Guardeon D13000V] - Fixed the crash issue
[NVRMini2]
1. [Sunell] - Fixed the bug that camera would randomly crash when re-connecting.
2. [ONVIF] - Disable the options of "Enable dual stream" of ONVIF/ONVIF models in the Titan
NVR and the Crystal.
3. [IQeye] - Fixed the bug that motion detection does not work.
4. [ONVIF/ONVIF] - Fixed the bug that getting video parameter fail when Profile do not contain any VideoEncoderConfiguration.
5. [LILIN IPD2322] - Fixed the bug that the minimum profile cannot be displayed.
6. [Hikvision DS-2CD7253F-EIZ] - Fixed the bug that zoom and focus function does not work.
7. [Santec SNC-6323IRH] - Fixed the bug that the minimum profile cannot be displayed in auto mode.
8. [CNB] – Fixed disconnection issues.
[NVRSolo]
1. [Sunell] - Fixed the bug that the camera would randomly crash when re-connecting.
2. [ONVIF] - Disable the options of "Enable dual stream" of ONVIF/ONVIF models in the Titan
NVR and the Crystal.
5 / 142
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 5
NVR Device Pack Release Note
NUUO version 3.7.0
3. [IQeye] - Fixed the bug that motion detection does not work.
4. [ONVIF/ONVIF] - Fixed the bug that get video parameter fail when Profile do not contain any VideoEncoderConfiguration.
5. [LILIN IPD2322] - Fixed the bug that the minimum profile cannot be displayed.
6. [Hikvision DS-2CD7253F-EIZ] - Fixed the bug that zoom and focus function does not work.
7. [Santec SNC-6323IRH] - Fixed the bug that the minimum profile cannot be displayed in auto mode.
8. [CNB] – Fixed disconnection issues.
[NVRTitan]
1. [Sunell] - Fixed the bug that the camera would randomly crash when re-connecting.
2. [ONVIF] - Disable the options of "Enable dual stream" of ONVIF/ONVIF models in the Titan
NVR and the Crystal.
3. [IQeye] - Fixed the bug that motion detection does not work.
4. [ONVIF/ONVIF] - Fixed the bug that get video parameter fail when Profile do not contain any VideoEncoderConfiguration.
5. [LILIN IPD2322] - Fixed the bug that the minimum profile cannot be displayed.
6. [Hikvision DS-2CD7253F-EIZ] - Fixed the bug that zoom and focus function does not work.
7. [Santec SNC-6323IRH] - Fixed the bug that the minimum profile cannot be displayed in auto mode.
8. [CNB] – Fixed disconnection issues.
[Crystal]
1. [Sunell] - Fixed the bug that the camera would randomly crash when re-connecting.
2. [ONVIF] - Disable the options of "Enable dual stream" of ONVIF/ONVIF models in the Titan
NVR and the Crystal.
3. [IQeye] - Fixed the bug that motion detection does not work.
4. [ONVIF/ONVIF] - Fixed the bug that get video parameter fail when Profile do not contain any VideoEncoderConfiguration.
5. [LILIN IPD2322] - Fixed the bug that the minimum profile cannot be displayed.
6. [Hikvision DS-2CD7253F-EIZ] - Fixed the bug that zoom and focus function does not work.
7. [Santec SNC-6323IRH] - Fixed the bug that the minimum profile cannot be displayed in auto mode.
8. [CNB] – Fixed disconnection issues.
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 6
6 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v3.6.0 (2014/8/05)
Modules:
Device Pack v 3.6.0
Dlink
Dlink-CN
Everfocus
Fine
Grundig
Sony
Trendnet
Vivotek
FW upgrade:
D-Link
Everfocus
Fine
Supported Systems:
Mainconsole v 4.1.12 and above*
NVRmini 2 v 1.7.1 and above**
NVRsolo
Titan NVR
NUUO Crystal™ v 1.6.2 and above v 2.0.3 and above
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
**For NVRmini 2 and NVRsolo multi stream setting function, please upgrade to NVRmini 2/NVRsolo v2.0.0 and above first.
New Camera Supported:
Arecont AV5245DN, AV20175DN
Axis
Bosch
M3025, M3027
Generic, NBN-40012, NDN-40012, NIN-40012, NUC-50022, NUC-51022,
NDN-50022, NDI-50022, NBN-50022
DCS-6517,DCS-7517,DCS-6112,DCS-6113,
DCS-H_Series, DCS-V_Series
ETN2260, EZN3361, EHN3361, EAN3300, EDN3340, EPN4220P, EPN4230
CDV-MV1080F-H, CDB-MD602
GCI-G1536F
SNC-EB632R
TV-IP262P, TV-IP262PI, TV-IP310PI, TV-IP311PI, TV-IP572P, TV-IP572PI,
TV-IP572W, TV-IP572WI, TV-IP672P, TV-IP672PI, TV-IP672W, TV-IP672WI
FD8168, SD8364E, IP8165HP, IP8155HP
DCS-7010L
EZN3340
CDV-5VM501
7 / 142
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 7
NVR Device Pack Release Note
NUUO version 3.7.0
Forenix
Sony
Zavio
Notice:
11. Bosch
IPB-1080BM, IPB-1080BL, IPV-1080CD, IPD-1080CD, IPX-1080DN
SNC-ER580 (FW 1.82.01)
D5210 a. Generic i. H.264 only support IP mode of GOP structure. (Camera→Encoder Profile→Profile N→ ii. iii.
Expert Settings→GOP structure→IP) (NUUO Server limitation)
Only support G.711 audio codec. (Camera performance limitation)
After changing MJPEG resolution on web and getting camera setting on NUUO, resolution will return to previous setting. (Camera firmware issue) iv. v. vi.
Snapshot resolution is not correspond to existing profile. (Camera firmware issue)
Can't set quality value of 3 rd stream. (Camera firmware issue)
Some resolution can't set framerate (NIN-733 Stream2 only support fps 7.5 under
1280x720 )(Camera performance limitation) vii. viii.
MJPEG framerate can't synchronize to web setting. (Camera performance limitation)
Can't set framerate 1 under base frame rate 50/60 ips mode. (Camera performance limitation)
NUUO does not test PTZ function. ix.
12. Zavio a. D5210 i. Due to camera restriction, some video setting will fail. This situation will be same as camera web. (Camera performance limitation)
13. Trandnet a. TV-IP262P i. FPS cannot be set to over 15 fps by cgi when it is 720P, but it can be set on web.(Camera Firmware Issue) ii. Sometimes setting by server is different with camera web. In fact, it already has been set successfully.(Camera Firmware Issue) b. TV-IP310PI i. Second stream is unable to change bitrate. (Camera firmware issue) ii. Frame rate list will be out of range when the resolution is 2048x1536.
fimware issue)
(Camera iii. Second stream is unable to achieve maximun FPS when resolution of main stream is
2048x1536. (Camera performance limitation)
8 / 142
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 8
NVR Device Pack Release Note
NUUO version 3.7.0 c. TV-IP672W i. Camera response slowly due to digest authentication.(Camera Performance Issue) ii. Image setting only can set with specific value. Otherwise, it will set fail. (Server
Limitation)
Ex. Specific values:
0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,100.
14. EverFocus a. ETN2260 i. ii. iii. iv. v. vi.
Not support CBR mode.(Camera firmware issue)
The quality value can't be sync with camera web.(Camera firmware issue)
Not support zoom and focus.(Camera firmware issue)
The resolution of snapshot always be 640x480.(Camera firmware issue)
The quality value can't be setup to 0, and the quality value can't be setup to 10 under
MJPEG.(Camera firmware issue)
If there are duplicate name of preset point, the function of GoTo preset point and
Clear All preset point will fail.(Camera firmware issue) b. EZN3340 i. The parameters of the camera are not configurable with MPEG4 format.(Camera ii. iii. iv. firmware issue)
Not support CBR mode.(Camera firmware issue)
Not support zoom and focus.(Camera firmware issue)
It will lose parameters of stream2 and stream3 if you disable stream2 and stream3 on camera web.(Camera firmware issue)
15. Fine a. CDV-5VM501 i. ii.
Bit rate list is incorrect. (Camera firmware issue)
Resolution of video stream might not change when configuration is changed to
2048x1536. (Camera firmware issue)
Camera is unable to achieve maximum FPS, when Quality set to the best. (Camera iii. iv. performance limitation)
Palyback is not smooth. (NUUO server limitation) b. TCP-HDVB800-H i. ii.
Camera is unable to achieve maximum FPS.(Camera performance limitation)
Audio has noise.(Camera firmware issue)
16. Sony a. SNC-EB632R i. PTZ only support zoom and focus.
9 / 142
Copyright © 2014 NUUO Inc. All rights reserved. www.nuuo.com 9
NVR Device Pack Release Note
NUUO version 3.7.0
Bug Fixed the bug thated:
Crystal:
1. [Sunell] – Fixed the bug that the issue that server sometimes can’t receive DI and MD event.
2. [Zavio] - Fixed the bug that the frame dropping issue when using H264 high profile
3. [Vista VK2-2MPVRD] - Fixed the bug that connection issue
4. [Arecont] – Fixed the bug that the bug of Arecone cameras can’t not load original video parameter value after upgrade DevicePack version from 3.1
Titan NVR:
1. [Sunell] – Fixed the bug that the issue that server sometimes can’t receive DI and MD event.
2. [Zavio] - Fixed the bug that the frame dropping issue when using H264 high profile
3. [Vista VK2-2MPVRD] - Fixed the bug that connection issue
4. [Arecont] – Fixed the bug that the bug of Arecone cameras can’t not load original video parameter value after upgrade DevicePack version from 3.1
Mainconsole:
1. [Onvif] - Fixed the bug that the issue that Mainconsole will crash after operating preset.
2. [Onvif] - Fixed the bug that the issue that Mainconsole will crash after operating preset functions.
3. [Sunell] – Fixed the bug that the issue that Mainconsole sometimes can’t receive DI and MD event.
4. [Zavio] - Fixed the bug that the frame dropping issue when using H264 high profile
5. [LG] – Fixed the bug that that Version 5.0.22 Crash all the time
NVRmini 2:
1. [Sunell] – Fixed the bug that the issue that server sometimes can’t receive DI and MD event.
2. [Zavio] - Fixed the bug that the frame dropping issue when using H264 high profile
3. [Vista VK2-2MPVRD] - Fixed the bug that connection issue
4. [Arecont] – Fixed the bug that the bug of Arecone cameras can’t not load original video parameter value after upgrade DevicePack version from 3.1
NVRsolo
10 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
1. [Sunell] – Fixed the bug that the issue that server sometimes can’t receive DI and MD event.
2. [Zavio] - Fixed the bug that the frame dropping issue when using H264 high profile
3. [Vista VK2-2MPVRD] - Fixed the bug that connection issue
4. [Arecont] – Fixed the bug that the bug of Arecone cameras can’t not load original video parameter value after upgrade DevicePack version from 3.1
Copyright © 2014 NUUO Inc. All rights reserved.
11 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v3.5.0 (2014/6/30)
Modules:
Device Pack v 3.5.0
Supported Systems:
Mainconsole v 4.1.12 and above*
NVRmini 2 v 1.7.1 and above**
NVRsolo
Titan NVR
NUUO Crystal™ v 1.6.2 and above v 2.0.3 and above
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
**For NVRmini 2 and NVRsolo multi stream setting function, please upgrade to NVRmini 2/NVRsolo v2.0.0 and above first.
New Camera Supported:
3S N5013, N9018
ACTi
Arecont
B53, B67, B94, I94
AV10255PMTIR, AV10256PMTIR, AV40185
Bosch
Dahua
Dlink
Dlink-CN
Everfocus
Fine
Forenix
IP Power
Samsung
NBN-498, NDN-498, NBC-455, NDC-455, NTI-40012, NTI-50022
HFW5200, SD6A230
DCS-935L
DCS-H30-51D/S, DCS-H41-11D/SI, DCS-H41-11D/SO, DCS-H42-21D/SA
DCS-H42-21D/SM, DCS-H70-21D/SA1, DCS-H70-21D/SM1
EHN3340, EPN4220
CDB-HFD728, CDB-HFD828, CDV-3VM800Z3, CDV-MFB2000D,
SP-HP2020C-IP, SP-HP2320C-IP, TCP-BF728IR, TCP-BF828IR,
TCP-HDVB800Z3
FBS-1300BX, FBS-1300ID, FBS-1300IDR, FBS-1300VD, FBS-1300VDR,
FBS-1300MID, FBS-1300MVD, FBS-1300BL
NCOA22F, NCOA32FD, NCOA52F, NDOA22F-W, NDOA32FD-W, NIAA202F
NIDA212F-W, NIDA312FD-W, NIDA512F-W, NIPA2H22-C, NIPA2H22-W
NIRA222F, NIRA232F, NIRA332FD, NITA212F, NITA312FD
SNO-6011R
12 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Vivotek FD8154
FW upgrade:
3S
Arecont
Everfocus
Fine
Vitek
Vivotek
N3072
AV12366DN
EAN3300, EDN3340, EHN3340, EPN4220
CDV-3VM501,TCP-MH802, TCP-IRH5030C, CDV-P360, TCP-VM501,
SP-HP2020Q-IP, TCP-IRH5040C
VTC-IR401
FD8363
New Feature:
1. Support Onvif DI/DO/Motion Detection notification via pull point subscription, audio output(talk)
2. Support multiple stream on Hikvision Generic
Notice:
17. 3SVision: a. N9018 ii. Audio choppy with G.726/32.(Camera firmware issue) iii.
18. Bosch:
The image of snapshot to FTP is from MJPEG stream. (camera firmware issue) a. NTI-40012, NTI-50022 i. H.264 only support IP mode of Bosch GOP structure. (NUUO Server limitation) ii. iii.
Only support G.711 audio codec. (Camera performance limitation)
After changing MJPEG resolution on web and getting camera setting on NUUO, iv. resolution will return to previous setting. (Camera firmware issue)
Snapshot resolution is not correspond to existing profile. (Camera firmware issue) b. NBN-498, NBC-455 i. ii.
H.264 only support IP mode of Bosch GOP structure. (NUUO Server limitation)
Only support G.711 audio codec. (Camera performance limitation) iii.
19. IPPower
It can't set up 3rd stream quality value. (Camera firmware issue) a. NCOA52F i. Camera with high resolution and quality is unable to achieve max fps. (Camera performance limitation)
13 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 ii. iii.
The range of bitrate isn’t synchronized with the one on camera’s web due to Onvif restriction. (Camera performance limitation)
The list of framerate isn’t synchronized with the one on camera’s web due to Onvif restriction. (Camera performance limitation)
Don’t support autodetect and search. (Camera firmware limitation) iv.
20. ACTi a. B57, B67, B94, I67 i. The camera with highest quality and resolution is unable to achieve 30 fps and audio
21. Everfocus stutter.(Camera performance limitation) a. EPN4220 i. The Audio-In status can't synchronize to web client. (ONVIF limitation) ii. iii.
Cannot change the rate control mode. (ONVIF limitation)
Cannot get snapshot by CGI(404). (Camera firmware issue) b. EHN3340 i. Onvif test tool get "No MPEG4 support" but actually it supports. (Camera firmware ii. iii. iv. v. issue)
The Audio-In status can't synchronize to web client. (O NVIF limitation)
Cannot change the rate control mode. (ONVIF limitation)
Cannot get snapshot by CGI(404). (Camera firmware issue)
The brightness only change when the value is 50 (Camera firmware issue)
22. FINE a. TCP-HDVB800Z3 i. The info. of stream profile display failure. b. CDV-MFB2000D i. ii. ii.
23. Vitek
Camera is unable to achieve maximum FPS. (Camera performance limitation)
The info. of stream profile display failure. (NUUO server limitation) c. TCP-MH802 i. Framerate may display incorrectly with MJPEG format. (Canera firmware issue)
Camera is unable to achieve maximum FPS. (Camera performance limitation) a. VTC-IR401 i. Disable talk function.(Camera firmware issue) ii. The camera with highest quality and resolution is unable to achieve 30 fps.(Camera performance limitation) iii. iv.
Sometimes UPNP search failed.(Camera firmware issue)
Motion detection may not trigger when closing audio function(Camera firmware issue)
14 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
24. Arecont a. AV10255PMTIR, AV12366DN i.
25. Dahua
Camera is unable to achieve maximum FPS. (camera performance limitation) a. IPC-HFW5200 i. Sometimes parameter dialog will fail to get codec parameter with high bitrate. ii.
(Camera performance limitation)
The configuration of parameter on camera will be changed by other parameter, our iii. iv. parameter dialog can't synchronize with camera. (Camera firmware issue)
Slow reaction when motion detection is triggered. (Camera performance limitation)
Polling the DI/Motion status will make audio stutter. (Camera performance limitation) b. SD6A230 i. The permitted parameter list on camera will be changed by other parameters, our parameter dialog can't synchronize with camera. (Camera firmware issue) ii. iii. iv. v.
The camera can't be searched by UPnP tools. (Camera firmware issue)
Slow reaction when motion detection is triggered. (Camera performance limitation)
Big audio noise with PCM. (Camera firmware issue)
CGI response "support flip/mirror", but actually not. (Camera firmware issue) vi. Polling the DI/Motion status will make audio stutter. (Camera performance limitation)
Bug Fixed the bug thated:
Crystal:
5. [Axis] - Fixed the bug that high bitrate when P7214 reset.
6. [Fine 5MP] - Fixed the bug that Camera parameters not synchronize with web.
7. [ACTi] - Fixed the bug that ACTi ACM3701 that won’t seem to go to the full resolution.
Titan NVR:
5. [Axis] - Fixed the bug that high bitrate when P7214 reset.
6. [Fine 5MP] - Fixed the bug that Camera parameters not synchronize with web.
7. [ACTi] - Fixed the bug that ACTi ACM3701 that won’t seem to go to the full resolution.
Mainconsole:
6. [DLink] i. Fixed the bug thated the issue that DCS-6513 cannot stop auto pan.
7. [Messoa] i. Fixed the bug thated the issue that NCR870 and NDF820 doesn’t enable multiple streams setting.
8. [HDPRO]
15 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 i. Fixed the bug thated the issue that HD-IC221STH211P doesn’t enable multiple streams setting.
9. [MegaIP] i. Fixed the bug thated the issue that NCD-2003PR doesn’t enable multiple streams setting.
NVRmini 2:
1. [Axis] - Fixed the bug that high bitrate when P7214 reset.
2. [Fine 5MP] - Fixed the bug that Camera parameters not synchronize with web.
3. [ACTi] - Fixed the bug that ACTi ACM3701 that won’t seem to go to the full resolution.
NVRsolo
5. [Axis] - Fixed the bug that high bitrate when P7214 reset.
6. [Fine 5MP] - Fixed the bug that Camera parameters not synchronize with web.
7. [ACTi] - Fixed the bug that ACTi ACM3701 that won’t seem to go to the full resolution.
16 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v3.4.0 (2014/6/5)
Modules:
Device Pack v 3.4.0
Supported Systems:
Mainconsole v 4.1.12 and above*
NVRmini 2 v 1.7.1 and above**
NVRsolo
Titan NVR
NUUO Crystal™ v 1.6.2 and above v 2.0.3 and above
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
**For NVRmini 2 and NVRsolo multi stream setting function, please upgrade to NVRmini 2/NVRsolo v2.0.0 and above first.
New Camera Supported:
ACTi B97 and E95
AXIS
CNB
M1004-W
MPC1070PN (fisheye camera)
Dahua
Dlink
Dlink-CN
Everfocus
Fine
Forenix
LG
Mobotix
TriCorps
Vista
Vitek
Vivotek
HCVR5104H
DCS-942LB1, DCS-6513
DCS-H50-21D/S
EDN2260
CDV-3VM800-H, TCP-2200AM-H, TCP-2700AM-W and TCP-HDVB800-H
ISPD II-1312WD and ISPD II-3018WD
LNP3020P and LNV7210R
Q25M-Secure(fisheye camera) and T25M-Secure(fisheye camera)
TCS-33B002-IRFH and TCS-36B002
VK2-1080BIR35V16e, VK2-1080BIR37e, VK2-1080VFD3V9F,
VK2-1080VFDIR37e, VK2-1080VRD3V9, VK2-1080VRDIR35V16e and
VK2-1080VRDIR37e
VTD-13VN, VTD-20VN-M, VTD-MV20VRN and VT-13FN-M
MD8531H, SD8363E and SF8174 (SD8363E and SF8174 are PPTZ)
17 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
FW upgrade:
AXIS M3007 (5.55.1.1)
Brickcom
Vivotek
Multiple Stream Setting:
30xN (3.2.2.8) and OSD-200A (gk20140422NSA)
VS8801 (VS8801-VVTK-0202a3.flash.pkg)
1. Support multiple stream setting function on ACTi E95, ACTi Generic, Mobotix Q25M-Secure,
T25M-Secure and ONVIF 2.0 Profile S with test tool v12.06 (test model see http://www.nuuo.com//mktmaterials/NVS/ONVIF.pdf
).
New Feature:
1. Arecont on DP v3.4.0 support bandwidth limitation function.
2. Vivotek on DP v3.4.0 support smart stream function* with Mainconsole, NVRmini 2, NVRsolo, and NUUO Crystal™ (v2.2).
* Smart stream function support only if Vivotek camera supports this function.
3. Centrix Generic and Dynacolor Generic on DP v3.4.0 support NUUO Dewarp function.
Notice:
1. Brickcom: b. OSD-200A(20xP) iv. v.
Digital input reaction is slow. (Camera performance limitation)
Snapshot is supported when the codec is MJPEG. (Camera performance limitation) c. FB-300Np(30xN) i. The Motion Detection may trigger continuously when the frame rate is 1. (Camera ii. firmware issue)
It will show error message when setup camera parameter to higher resolution.
(NUUO Crystal™ limitation)
2. CNB: a. MPC1070PN i. ii. iii.
Camera is unable to achieve maximum FPS. (Camera performance limitation)
Audio stutter with G.711. (Camera firmware issue)
MJPEG bitrate setting is tied to FPS setting and will change base on any FPS changes.
(Camera performance limitation) iv. 2nd stream and 3rd stream are unable to achieve 500/100 kbps. (Camera performance limitation)
3. Dahua: a. HCVR5104H
18 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 i. ii. iii. iv. v.
The bitrate list of camera isn’t synchronized with the one on camera’s web. (NUUO server limitation)
The auto detection and UPnP search are not supported. (Camera firmware issue)
The audio-in function is only supported in channel 1. (Camera firmware issue)
The PCM audio format is not supported. (Camera firmware issue)
The talk function is not supported. (Camera firmware issue) vi. The move and auto-pan functions of PTZ are not supported. (Camera firmware issue) vii. After focus- near or focus-far, camera automatically switches to autofocus immediately.
(Camera firmware issue) viii. The auto-focus is not supported. (Camera firmware issue) ix. x.
The motion detection is not supported. (Camera firmware issue)
The parameters of the camera are not configurable with low FPS. (Camera firmware issue)
4. DLink: a. DCS-6513 i. ii.
DCS-6513 PTZ supports zoom and focus. (Camera performance limitation)
First time connection may take about 30 seconds due to the need for camera
5. EverFocus: configuration. (Camera performance limitation). a. EDN2260: i. The quality list of H.264 isn’t synchronized with the one on camera’s web. (Camera firmware issue)
6. Fine: a. TCP-HDVB800-H i. ii.
Camera is unable to achieve maximum FPS.(Camera performance limitation)
Audible noise. (Camera firmware issue)
7. Forenix: a. ISPDII-3018WD i. 2 nd stream is unable to achieve 500/100 kbps, when main stream resolution is 3M, ii.
SXGA or D1. (Camera performance limitation)
Camera with quality over 8192 is unable to achieve maximum FPS. (Camera firmware issue) b. ISPDII-1312WD i. 2 nd stream is unable to achieve 500/100 kbps, when main stream resolution is 3M, ii.
SXGA or D1. (Camera performance limitation)
Camera with quality over 8192 is unable to achieve maximum FPS (Camera performance limitation)
19 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 iii. Camera will automatically pan or tilt, every 30 seconds or 2 minutes indefinitely. 1 minute after this motion occurred, the camera cannot tilt during this 1 minute period.
8. Histream:
(Camera firmware issue) a. HH9803C-L16 i. Due to Onvif restriction, some frame rate and bit rate cannot be set. (Camera iii. ii. performance limitation)
MPEG4 is not supported. (Camera firmware issue)
The MJPEG quality selection list on a camera is not synchronized with the one on the camera's web settings page. (Camera firmware limitation)
9. Jetstor: a. JV-B1201R i. ii.
Due to Onvif restriction, some frame rate and bit rates cannot be set. (Camera performance limitation)
Camera 2 nd and 3 rd stream is unable to change resolution. (Camera firmware limitation)
10. LG: a. LNP3020 i. Snapshot is not supported. (Camera performance limitation) b. LNV7210R i. Video parameter (brightness…etc) setting is not supported. (Camera performance limitation)
11. Mobotix: a. T25M-Secure i. Camera movements became imprecise under panoramic mode.(NUUO Server limitation) b. Q25M-Secure ii. Camera movements became imprecise under panoramic mode.(NUUO Server limitation)
12. Qihan: a. QH-NV431 i. ii.
Due to Onvif restriction, some bit rates cannot be set. (Camera performance limitation)
When main stream Liveview is on highest bitrate, the 2 nd or 3 rd stream disconnects.
(Camera performance limitation)
13. TriCorp: a. TCS-33B002-IRFH
20 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 i. ii.
System response is slow when switching to MPRG-4 encoding format (Camera performance limitation)
System response is slow to receive camera stream when connecting for the first time.
(Camera performance limitation) iii. iv.
Camera with MJPEG format will have mosaic effect. (Camera firmware limitation)
Camera is unable to achieve maximum FPS (Camera performance limitation) b. TCS-36B002 i. Need very long time to switch MPEG4 codec. (Camera performance limitation) ii. Need very long time to receive stream when first time used. (Camera performance limitation) iii. iv. v.
14. Tyco:
Camera with MJPEG format will have mosaic effect. (Camera firmware limitation)
Motion detection is not supported. (Camera firmware limitation)
Camera is unable to achieve maximum FPS (Camera performance limitation) a. ADVEIPSD37AH i. Due to Onvif restriction, some frame rate and bit rates cannot be set. (Camera iv. performance limitation)
The MJPEG quality selection list on a camera is not configurable. (Camera firmware issue) The MJPEG quality selection list on a camera
15. Vista: a. VK21080VFD3V9F i.
16. Vivotek:
VK21080VFD3V9F PTZ supports zoom and focus. (Camera performance limitation) a. SD8363E ii. The video parameter setting will get false value. (Camera performance limitation) b. MD8531H iii. The video parameter setting will get false value. (Camera performance limitation)
17. WAPA: a. BL-C7HA1080IL-T18 iv. Due to Onvif restriction, some bit rates cannot be set. (Camera performance limitation) i. The frame rate of the camera is not configurable. (Camera firmware limitation)
21 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Bug Fixed the bug thated:
Mainconsole:
1. [DLink] ii. Fixed the bug thated the issue that DCS-6513 cannot stop auto pan. iii. Fixed the bug thated the issue that enable/disable audio out will change camera volume.
2. [Mobotix] iv. Fixed the bug thated the issue that motion detection may not trigger when adding new “Image Analysis Events” profile.
3. [Forenix] v. Fixed the bug thated the issue that the FPS setting of IPB-1080BM, IPB-1080BL,
IPV-1080CD, IPD-1080CD and IPX-1080DN isn’t synchronized with the one on camera’s web.
4. [Axis] vi. Audio function on Liveview now supports Axis P3346 camera. vii. Fixed the bug thated the issue that P7214 audio-in isn’t synchronized with the one on camera’s web.
5. [ACTi] viii. Fixed the bug thated compatibility issues with adding ACTi KCM5611.
6. [Hikvision] ix. Fixed the bug thated the issue that DS-6601HF is disconnected. x. Corrected possible issues caused by multi-stream connection with Hikvision generic.
7. [Vivotek] xi. Trigger motion no longer fails when setting more than 1 motion area detection triggers on the camera web setting page.
NVRmini 2:
1. [Axis] i. Fixed the bug thated the issue that P7214 audio-in isn’t synchronized with the one on camera’s web.
2. [Forenix] i. Fixed the bug thated the issue that the FPS setting of IPB-1080BM, IPB-1080BL,
IPV-1080CD, IPD-1080CD and IPX-1080DN isn’t synchronized with the one on camera’s web.
3. [Vivotek] i. Trigger motion no longer fails when setting more than 1 motion area detection triggers on the camera web setting page.
22 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
4. [Vista] i. Fixed the bug thated Vista VK2-600PTZ random disconnection issue.
NVRsolo
1. [Axis] i. Fixed the bug thated the issue that P7214 audio-in isn’t synchronized with the one on camera’s web.
2. [Forenix] i. Fixed the bug thated the issue that the FPS setting of IPB-1080BM, IPB-1080BL,
IPV-1080CD, IPD-1080CD and IPX-1080DN isn’t synchronized with the one on camera’s web.
3. [Vivotek] i. Trigger motion no longer fails when setting more than 1 motion area detection triggers on the camera web setting page.
4. [Vista] i. Fixed the bug thated Vista VK2-600PTZ random disconnection issue.
Titan NVR:
1. [Axis] i. Fixed the bug thated the issue that P7214 audio-in isn’t synchronized with the one on camera’s web.
2. [Forenix] i. Fixed the bug thated the issue that the FPS setting of IPB-1080BM, IPB-1080BL,
IPV-1080CD, IPD-1080CD and IPX-1080DN isn’t synchronized with the one on camera’s web.
3. [Vivotek] i. Trigger motion no longer fails when setting more than 1 motion area detection triggers on the camera web setting page.
4. [Vista] i. Fixed the bug thated Vista VK2-600PTZ random disconnection issue.
23 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v3.3.0 (2014/5/5)
Modules:
Device Pack v 3.3.0
Supported Systems:
Mainconsole v 4.1.12 and above*
NVRmini 2 v 1.7.1 and above**
NVRsolo
Titan NVR
NUUO Crystal™ v 1.6.2 and above v 2.0.3 and above
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
**For NVRmini 2 and NVRsolo multi stream setting function, please upgrade to NVRmini 2/NVRsolo v2.0.0 and above first.
New Camera Supported:
Arecont AV12366DN
Bosch
Dahua
NBN-733, NBN-832, NDN-733, NDN-832, NIN-733 and NIN-832
SD6366E-HN
Dlink
Fine
Forenix
HDPRO
QVS
Santec
DCS-6112B1, DCS-930LB1 and DCS-932LB1
CDB-720VIR-H, TCP-2700AM, TCP-BF1080 and TCP-HVB3100D
FBU-301LWD
HD-IC221STH211P
Generic
SNC-3303, SNC-4323IR, SNC-5323IRH, SNC-6303 and SNC-6323IRH
24 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Sony
Vivotek
SNC-HM662 (fisheye camera) and SNC-VM601B
FD8171, IP8355EH and IP8365EH
FW upgrade:
Arecont
Everfocus
Forenix
AV5115 (65225)
EZN3260 (1.2.4)
FBU-200LWD, FBU-201LWD, FBX-200CL, FBX-200LWD,
FDM-200LWD, FVD-200LWD
(cramfsImage_AgWT8200122N06_1401213F) , FBU-300LWD ,
FBX-300LWD, FDM-300LWD and FVD-300LWD
(cramfsImage_AgWT8300036N06_1401214F)
Multiple Stream Setting:
1. Support multiple stream setting function on Santec SNC-3303, SNC-4323IR, SNC-5323IRH,
SNC-6303, SNC-6323IRH and Mobotix D15D-Sec, D15D-Sec-Dnight, D15D-Sec-Night-Pano,
D15D-Sec-Pano, M15D-Sec, M15D-Sec-Dnight, M15M-Sec, S15D-Sec, S15M-Sec and
S15M-Sec-Night
New Feature:
1. Sony G6 series on DP v3.3.0 support multiple stream settings with Mainconsole v5.0.0 and
NVRmini 2/NVRsolo v2.0.0 and above.
2. Axis PQM series and Vivotek 8000 series on DP v3.3.0 support CBR/VBR settings with NVRmini
2/NVRsolo v2.0.0, Titan v1.6.2 and NUUO Crystal™ v2.0.4 and above.
3. Brickcom 50xA and 30xN on DP v3.3.0 support resolution dynamically changes based on the camera's maximum resolution.
Notice:
1. Bosch: i. ii. iii. vi. NIN-733
Camera only supports IP mode of GOP structure under H.264 format.
Camera only supports G.711 audio codec.
The multi-stream setting of the camera is not configurable due to the limitations of inter-streaming dependency.(Mainconsole only) vii. NDN-832 i. ii.
Camera only supports IP mode of GOP structure under H.264 format.
Camera only supports G.711 audio codec.
25 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 iii. iv.
2. Brickcom a. OB-200Ap(50xA) i. The frame rate list with camera stream mode -- Wide and Ultra-Wide isn’t synchronized with the one on camera’s web. (camera firmware issue) ii.
With camera stream mode -- H.264 MP SD user can change resolution from 1920x1080 or 1280x720 to lower resolution.
The multi-stream setting of the camera is not configurable due to the limitations of inter-streaming dependency.(Mainconsole only) iii.
Under the protocol HTTP, the RTSP stream will disconnect within 5 minutes. (camera performance limitation)
There is a display mosaic issue when the format is MJPEG and resolution is 2592x1944 or 2304x1728. iv. v.
The zoom and focus function have no response via camera web or CGI command.
(camera firmware issue)
It will show error message when setup camera parameter to higher resolution. (NUUO
Crystal™ only) vi. The image of OB-200Ap sometimes cannot be updated under the protocol of TCP.
(NUUO Crystal™ only) b. OB-200Np(30xN) i. Under the protocol HTTP, the RTSP stream will disconnect within 5 minutes. (camera ii. performance limitation)
The zoom and focus function have no response via camera web or CGI command.
(camera firmware issue)
Motion detection may trigger when frame rate is 1. (camera firmware issue) iii. iv. It will show error message when setup camera parameter to higher resolution. (NUUO
Crystal™ only)
3. Dahua a. SD6366E-HN i. The list of camera bitrate isn’t synchronized with the one on camera’s web. User should apply a value in the valid range from the web page of the camera so that the setting can ii.
4. DLink be applied successfully.
Autofocus is not supported. (camera firmware issue) a. DCS-6112B1 i. The camera with highest quality and MJPEG format is unable to achieve 30 fps.(camera ii. firmware issue)
Audio out is not supported. (camera firmware issue)
26 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 b. DCS-930LB1 i. Auto detection is not supported. (camera firmware issue)
5. EverFocus a. EZN3260 i. ii.
The camera resolution of the third stream is unable to achieve 160x128. (NVRmini
2/NVRsolo/Titan NVR/NUUO Crystal™)
The information of camera 2 nd stream and 3 rd stream are not synchronizes with the one on camera’s web when disable and enable the 2 nd and 3 rd stream on camera’s web. iii.
(camera firmware issue)
The list of camera quality isn’t synchronized with the one on camera’s web with CBR.
(NUUO server limitation)
6. Fine a. TCP-BF1080, CDB-720VIR-H i. ii.
The camera frame rate is unable to achieve 20/30 fps. (camera firmware issue)
The stream profile information does not display correctly. (Mainconsole only)
7. Forenix a. FBU-200LWD i. ii. iii.
Camera DI is not supported. (camera firmware issue)
Camera snapshot function is not supported. (camera firmware issue)
The camera 2 nd and 3 rd stream with D1 and SXGA resolution is unable to achieve
500bps/100bps. (camera firmware issue) b. FVD-300LWD i. ii. iii.
Camera DI is not supported. (camera firmware issue)
Camera snapshot function is not supported. (camera firmware issue) iv.
The camera with TCP connection is unable to achieve its frame rate setting. (camera firmware issue)
The camera 2 nd and 3 rd stream with D1 and SXGA resolution is unable to achieve
500bps/100bps. (camera firmware issue)
8. HDPRO a. HD-IC221STH211P i. ii.
The multi-stream will depend on stream setting on camera web.
Audio only support G.711 codec.
9. Mobotix a. M15D-Sec, S15D-sec, D15d-Sec i. The camera with higher quality and resolution is unable to achieve the fps which users set for all streams.(camera firmware issue)
27 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 ii. The 2 nd and 3 rd stream resolution will depends on 1 st stream resolution setting. For example, if users set the resolution of 1st stream to 2048*1536(the ratio of height and width is 4:3) and 2nd stream resolution is 1920*1080, the 2nd stream resolution will become 1440*1080(4:3) instead of 1920*1080(16:9). (camera performance limitation)
10. Santec a. SNC-3303, SNC-6323IRH i. Audio has noise with the camera format MJPEG, resolution 1920x1080, frame rate
25fps, quality 70 and TCP protocol. ii. iii.
When disable MJPEG stream, camera snapshot function is not supported
Camera with MJPEG format and 1920x1080 resolution is unable to achieve 20 fps
11. Sony a. SNC-HM662 i. ii. iii. iv.
With JPEG format and resolution 2560x1920 does not support audio.
Only all streams with default RTSP path are supported.
Camera is unable to achieve the maximum FPS.
Sometimes, stream setting may be failed. b. SNC-EB630 i. Sometimes, the 3 rd stream setting is not configurable.
Bug Fixed the bug thated:
Mainconsole:
8. [VisionHitech] Fixed the bug thated the issue that camera Vision-SMi stream is disconnected.
NVRmini 2:
5. [Samsung] Fixed the bug thated the issue that SNF-7010 2 nd stream is disconnected.
6. [Centrix] Fixed the bug thated compatibility issues with using generic model.
NVRsolo
1. [Samsung] Fixed the bug thated the issue that SNF-7010 2 nd stream is disconnected.
2. [Centrix] Fixed the bug thated compatibility issues with using generic model.
Titan NVR:
1. [Samsung] Fixed the bug thated the issue that SNF-7010 2 nd stream is disconnected.
2. [Centrix] Fixed the bug thated compatibility issues with using generic model.
28 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
NUUO Crystal™:
1. [Samsung] Fixed the bug thated the issue that SNF-7010 2 nd stream is disconnected.
2. [Centrix] Fixed the bug thated compatibility issues with using generic model.
Release Version v3.2.1 (2014/4/23)
Modules:
Device Pack v 3.2.1
Supported Systems:
Mainconsole v 4.1.12 and above*
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
Bug Fixed the bug thated:
Mainconsole:
9. [Axis] Fixed the bug thated compatibility issues with using multi stream function.
10. [Vivotek] Fixed the bug thated compatibility issues with using multi stream function.
29 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v3.2.0 (2014/4/7)
Modules:
Device Pack v 3.2.0
Supported Systems:
Mainconsole v 4.1.12 and above*
NVRmini 2 v 1.7.1 and above**
NVRsolo
Titan NVR
NUUO Crystal™ v 1.6.2 and above v 2.0.3 and above
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
**For NVRmini 2 and NVRsolo multi stream setting function, please upgrade to NVRmini 2/NVRsolo v2.0.0 and above first.
New Camera Supported:
ACTi I51(fisheye camera) and I71(fisheye camera)
AMTK
Arecont
AH2816T (Fisheye camera)
AV3455 and AV10225
Dlink
Fine
Guardeon
Levelone
Samsung
Sony
Vitek
DCS-7000L
TCP-HFB720-H
GND-D2300V, GND-D3200, GND-F2300 and GND-H2300IR
FCS-5042
SND-6011R and SNV-7080R
SNC-WR600, SNC-WR602, SNC-XM632, SNC-XM636 and SNC-XM637
VTC-IR401/210NP
30 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Vivotek
Wavekrom
FD8355EHV and FD8365EHV
WK-SD6000HD
FW upgrade:
Arecont
CNB
Dlink
Fine
AV10115 and AV10255 (65225)
IDC4050VF (XNET.M1-3.00.13.1125), INS2000
(FW XNET.A1-2.01.13.0902) and
IVC5055VR(XNET.M1-3.00.13.1125)
DCS-3714 (FW: V1.00.00) and DCS-6115 (FW: V0.09.00)
ACM-V3103 (FW: 2.03.14A) and TCP-HVB3105D (FW: v2.03.14A)
FCS-3062 (FW: 1.0.0.6build4), FCS-4041 (FW: Le20140113NSA),
FCS-4042 (FW: Le20140113NSA) and FCS-5052(FW: 1.0.0.6build4)
Levelone
Samsung
Sunell
Vision Hitech
Zavio
SNO-7080R(FW 2.00_121004)
SN-IPR54/31UDN (FW: v1.7.1001.3.0.13)
Vision SM3Ti (VISION_M3Ti_2014.02.27_v.1.1.5.13.dat)
D7320 (FW: M3.1.5.21)
Multi Stream Setting:
2. Support multi stream setting function on Santec SNC-3302, SNC-3305, SNC-3322, SNC-4302,
SNC-5312IR, SNC-5315IR, SNC-6202, SNC-6212IR, SNC-6302, SNC-6312IRH, SNC-6315IRH,
SNC-8322I/HO, Samsung SND-6011R, SNV-7080R, SNO-7080R and all Sunell models.
New Feature:
4. Support multi stream setting function with NVRmini 2/NVRsolo v2.0.0 and above on Axis PQM series from DP v3.2.0.
5. Support Snapshot function* with NVRmini 2/NVRsolo v2.0.0 and above on Axis PQM series,
Arecont camera, Sony G6 series, Vivotek 8000 series, Honeywell HDZ20HD HDZ20HDE,
HDZ20HDEX, HDZ20HDX and Hikvision DS-2CD2012-I, DS-2CD2112-I, DS-2CD2212-I3,
DS-2CD2212-I5, DS-2CD2312-I, DS-2CD2612F-I, DS-2CD2612F-IS, DS-2CD2632F-IS,
DS-2CD2712F-I, DS-2CD2712F-IS, DS-2CD2732F-IS, DS-2CD7253F-EIZ, DS-2CD8253F-EI,
DS-2CD8264FWD-EIS, DS-2CD864FWD-E, DS-2DF1-572, DS-6601HFHI, Generic from DP v3.2.0.
*One of the cameras in the system must support I/O functions in order to enable the snapshot feature. This is a known issue and we are looking to Fixed the bug that it with the next product version update.
6. Support PTZ function on ACTi Generic.
31 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
7. Support Santec four motion areas detection on Santec SNC-3302, SNC-3305, SNC-3322,
SNC-4302, SNC-5312IR, SNC-5315IR, SNC-6202, SNC-6212IR, SNC-6302, SNC-6312IRH,
SNC-6315IRH, SNC-8322I/HO.
8. Support Vivotek smart stream function on Mainconsole.
Notice:
1. Acti: a. I71 i. The camera resolution N640x360 should be N640x480.
2. CNB: a. CNB-IDC4050VF i. Cameras with VGA resolution will be unable to change bitrates. (camera firmware issue) b. CNB-INS2000 i. Camera is unable to achieve maximum FPS. (camera firmware issue) ii. ii.
Audio stutter with G.711. (camera firmware issue)
The FPS setting for 2 nd stream will get false value (25 or 30) (camera firmware
3. Dlink: iii. issue)
Camera is unable to change bitrate. (camera firmware issue) a. DCS-3714 i. The camera with highest quality and resolution is unable to achieve 30 fps.
(camera firmware issue) b. DCS-6115 i. The camera with highest quality and MJPEG format is unable to achieve 30 fps and audio will stutter. (camera firmware issue) c. DCS-7000L ii. The camera with highest quality/resolution and MJPEG format is unable to achieve iii.
30 fps. (camera firmware issue)
The parameters of the camera are not configurable with H.264 format. (camera iv. v. firmware issue)
The format of the camera is not configurable from MJPEG to H.264. (camera firmware issue)
The list of camera format MPEG4 isn’t synchronized with the one on camera’s web. vi.
If user sets camera format to MPEG4, camera will crash. (camera firmware issue)
Motion detection may not trigger continuously. (camera firmware issue)
4. Fine: a. ACM-V3103, TCP-HVB3105D
32 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 i. ii.
Camera will be disconnected when disabling camera MJPEG format on camera’s web.
Camera with resolution 1920x1080 is unable to achieve 20 fps. (camera firmware issue) iii. Video and audio stream malfunction within a period of time. (camera firmware issue).
5. Guardeon: a. GDN-H2300IR i. Camera will reboot (duration 60 seconds) after parameter configuration. (camera firmware issue)
Talk function not supported. audio in with 16 KHz sampling rate not supported. camera UPnP search not supported. (camera firmware issue) vii.
6. LevelOne: a. FCS-4042 i. After quality setting change, the camera is unable to achieve 30 fps. ii. iii.
The special symbol usage ex:# for camera preset point name will fail.
It will take 50~60 seconds in MJPEG format and maximum resolution setting
7. Sunell: a. All Sunell models has MJPEG codec removed. (Mainconsole) b. SN-IPR54/31UDN i. Due to Onvif restriction, some frame rate and bit rates cannot be set.
8. VisionHitech: a. M3Ti i. ii.
NUUO use dual mode as default connection mode.
Camera with format MJPEG and resolution VGA is unable to achieve the camera setting fps.
9. Vitek: a. VTC-IR401 i. Camera fps is unable to achieve the camera setting fps. (camera performance issue)
10. Zavio: ii. UPnP search may not work. (camera performance issue) a. D7320 i. Camera fps is unable to achieve the desired fps.
Bug Fixed the bug thated:
33 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Mainconsole:
11. [LG] Fixed the bug thated compatibility issues with adding cameras LG LVS201.
12. [Onvif/Onvif] Fixed the bug thated the issue that causes Mainconsole to restart when selecting onvif/onvif settings on a camera
13. [Arecont] Fixed the bug thated the display mosaic issue on Arecont AV10115 when switching to D/N mode in live view.
14. [Zavio] Corrected PTZ speed range and auto pan speed setting on Zavio P6210 and 812x cameras.
15. [Messoa] Messoa PRO series cameras are now correctly labeled as "Messoa Pro" cameras.
16. [Messoa] Messoa NCB858 is now correctly labeled. (previously labeled as NCR858)
NVRmini 2:
3. [Axis] Dewarp function now supports Axis M3007 camera.
4. [Arecont] Fixed the bug thated the display mosaic issue on Arecont AV10115 when switching to D/N mode in live view.
5. [D-Link] Corrected possible issues caused by dual stream connection with D-link DCS-2210 camera.
6. [Messoa] Messoa PRO series cameras are now correctly labeled as "Messoa Pro" cameras.
7. [Messoa] Messoa NCB858 is now correctly labeled. (previously labeled as NCR858)
8. [Sunell] Fixed the bug thated the issue that causes frame rate to double when enabling audio functions.
NVRsolo:
9. [Axis] Dewarp function now supports Axis M3007 camera.
10. [Arecont] Fixed the bug thated the display mosaic issue on Arecont AV10115 when switching to D/N mode in live view.
11. [D-Link] Corrected possible issues caused by dual stream connection with D-link DCS-2210 camera.
12. [Messoa] Messoa PRO series cameras are now correctly labeled as "Messoa Pro" cameras.
13. [Messoa] Messoa NCB858 is now correctly labeled. (previously labeled as NCR858)
14. [Sunell] Fixed the bug thated the issue that causes frame rate to double when enabling audio functions.
Titan NVR:
1. [Axis] Dewarp function now supports Axis M3007 camera.
2. [Arecont] Fixed the bug thated the display mosaic issue on Arecont AV10115 when switching to D/N mode in live view.
3. [D-Link] Corrected possible issues caused by dual stream connection with D-link DCS-2210 camera.
4. [Messoa] Messoa PRO series cameras are now correctly labeled as "Messoa Pro" cameras.
34 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
5. [Messoa] Messoa NCB858 is now correctly labeled. (previously labeled as NCR858)
6. [Sunell] Fixed the bug thated the issue that causes frame rate to double when enabling audio functions.
NUUO Crystal™:
3. [Axis] Dewarp function now supports Axis M3007 camera.
4. [Arecont] Fixed the bug thated the display mosaic issue on Arecont AV10115 when switching to D/N mode in live view.
5. [D-Link] Corrected possible issues caused by dual stream connection with D-link DCS-2210 camera.
6. [Messoa] Messoa PRO series cameras are now correctly labeled as "Messoa Pro" cameras.
7. [Messoa] Messoa NCB858 is now correctly labeled. (previously labeled as NCR858)
8. [Sunell] Fixed the bug thated the issue that causes frame rate to double when enabling audio functions.
Release Version v3.1.0 (2014/3/5)
Modules:
Device Pack v 3.1.0
Supported Systems:
Mainconsole v 4.1.12 and above*
NVRmini 2 v 1.7.1 and above**
NVRsolo
Titan NVR
NUUO Crystal™ v 1.6.2 and above v 2.0.3 and above
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
**For NVRmini 2 and NVRsolo multi stream setting function, please upgrade to NVRmini 2/NVRsolo v2.0.0 and above first.
New Camera Supported:
ACTi E96 (fisheye camera) and Generic model
Alarm.com
Arecont
ADC-V520, ADC-V620PT and ADC-VS420
AV1455, AV2146, AV2225, AV2226, AV2245, AV2246, AV3225, AV3226,
AV3245 and AV3246
35 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Axis
Dahua
DlinkCN
Fine
GE
Levelone
Messoa
Samsung
Sony
Vision Hitech
Vista
Vivotek
Zavio
FW upgrade:
Arecont
Dlink
Panasonic
Samsung
P1353-E, P1355-E, P1357, Q1931-E and Q6042
IPC-HD2100 and IPC-HFW3200C
DCS-H70-22D
ACM-V3103, TCP-HVB3105D and TCP-MZ602
TVC-M1245E-2M-P
FCS-3062 and FCS-4042
NCR870 and NDF820
SND-6084R, SNO-6084R, SNV-6012M and SNV-6084R
SNC-EM632R, SNC-VB635, SNC-WR630 and SNC-WR632
M2TiA, MTi, VD102i, VD10M2, VN10M2 and VN200i
VK2-1080VRDIR3V9F
FD8371EV, FE8174, FE8174V and VS8100
F3215 and P6210
AV1115, AV1125, AV1145, AV1255, AV1305 , AV2115, AV2805,
AV3105 and AV3115 (65225)
DCS-2132LB1 (FW v2.00.05) and DCS-3112 (FW v1.11.01)
WV-SW174W (FW: 1.81)
SNB-6004, SND-6084 (1.00_130316)
New Feature:
NVRmini 2/NVRsolo:
1. Support multi stream setting function with NVRmini 2/NVRsolo v2.0.0 and above on
Arecont camera and Vivotek 8000 series from DP v3.1.0.
2. Support multi stream setting function with requested cameras. (please refer to http://www.nuuo.com/SupportCamera.php?node_id=4#4 )
3. Support audio out function with NVRmini 2/NVRsolo v2.0.0 and above on Axis PQM series,
Sony 6 th generation and Vivotek 8000 series.
Notice:
1. Fine: b. ACM-V3103, TCP-HVB3105D i. The camera is unable to achieve 20 fps with a resolution of 2046x1536. (camera ii. firmware issue)
The video stream with MJPEG format will be disconnected when disable the MJPEG option on camera’s web.
36 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 iii.
2. Arecont:
Support zoom and focus. a. AV1115 i. DI and DO cannot work. b. AV3115 i. DO cannot work.
3. Alarm.com: a. ADC-V520 i. The resolution list is not synchronized with the one on camera’s web. (camera firmware issue). ii. The camera with high resolution and quality/ bitrate is unable achieve to 30fps with
MJPEG format and TCP protocol. iii. The video stream will be disconnected with a setting of MPEG4 and 20kbps bitrate. b. ADC-V620PT i. The resolution list is not synchronized with the one on camera’s web. (camera firmware issue). ii. Main stream cannot achieve high fps when use high resolution (1280x720 or higher) and high quality/ bitrate.
4. DlinkCN a. DCS-H70-22D i. The resolution list is not synchronized with the one on camera’s web. (camera firmware issue). ii. The camera is unable to achieve 15fps or above with some resolutions. (camera firmware issue)
5. Dlink a. DCS-2132LB1 i. Motion detection may not trigger continuously within short period of time. (camera firmware issue) b. DCS-3112 i. With MPEG4 format, the resolution list is not synchronized with the one on ii. camera’s web. (camera firmware issue).
Under multi stream function, low and min stream cannot reach 500 kbps and 100 kbps.
6. Panasonic: a. WV-SW174W i. MJPEG frame rate will be impacted by H.264 stream. If enable H.264 stream on main or low stream, MJPEG stream can only support up to 5 fps.
37 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
7. Zavio: a. F3215 i. ii.
Not support MPEG4 format. (camera firmware issue)
Audio out will stutter.
8. Dahua: a. IPC-HFW3200C i. The list of bit rate and frame rate is not synchronized with the one on camera’s web.
This may cause stream parameter setting fail. (camera firmware issue) ii. iii. iv. v.
Enable motion detection under MJPEG mode may cause liveview image to freeze.
The audio will stutter under PCM format.
The audio will stutter under G.711Mu and G.711A format.
With UPnP search the camera will search incorrect MAC address. (NVRMini vi.
2/NVRsolo/Titan NVR/NUUO Crystal™)
The bit rate of the cameras is not configurable on NVRSolo/NVRMini2 v2.0.0 web client with DP v3.1.0, but can be setup with NVRsolo local site. b. IPC-HD2100 i. The list of bit rate and frame rate is not synchronized with the one on camera’s web.
This may cause stream parameter setting fail. (camera firmware issue) ii. iii.
Enable motion detection under MJPEG mode may cause liveview image to freeze.
With UPnP search the camera will get incorrect MAC address. (NVRMini
2/NVRsolo/Titan NVR/NUUO Crystal™)
The bit rate of the cameras is not configurable on NVRsolo/NVRMini2 v2.0.0 web iv.
9. VisionHitech client with DP v3.1.0, but can be setup with NVRsolo local site. i. Main stream support H.264 format, low/min stream support H.264 and MJPEG.
(NVRMini 2/NVRsolo/Titan NVR/NUUO Crystal™) ii. iii. iv. v.
M2TiA series under H.264 format cannot setup D1resolution. (camera firmware issue)
It is invalid setting on brightness. (Mainconsole)
NUUO use dual mode as default connection mode.
It does not support the resolution setting for MJPEG. (Mainconsole)(camera firmware issue)
10. IP Power i. With NVRsolo v2.0.0 and above with DP v3.1.0 can select camera model on local site.
Bug Fixed the bug thated:
38 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Mainconsole:
10. [Hikvision] Fixed the bug thated the issue that camera will become manual focus mode when reconnecting the camera or restarting Mainconsole.
11. [Dlink] Fixed the bug thated the issue on DCS-5615 that the default brightness setting is not synchronized with the camera’s web.
12. [Dlink] Fixed the bug thated the issue on DCS-942L that the stream format and frame rate is not synchronized with Mainconsole settings.
13. [Vivotek] Fixed the bug thated the issue on VS8401 / VS8801 that only the first channel of the camera is connectable.
NVRmini 2:
1. [Onvif] Fixed the bug thated the issue that Onvif/Onvif will use first profile for default connecting profile.
2. [Vitek] Fixed the bug thated UPnP search fail issue.
3. [Hikvision] Fixed the bug thated the issue that the camera parameters are not changed by generic model.
4. [Axis] Fixed the bug thated the issue that the camera will disconnected when changing grid layout.
5. [CNB] Fixed the bug thated the issue that the multi stream is disconnected.
6. [Centrix] Fixed the bug thated the issue that the multi stream information is incorrect displayed for generic model.
NVRsolo:
1. [Onvif] Fixed the bug thated the issue that Onvif/Onvif will use first profile for default connecting profile.
2. [Vitek] Fixed the bug thated UPnP search fail issue.
3. [Hikvision] Fixed the bug thated the issue that the camera parameters are not changed by generic model.
4. [Axis] Fixed the bug thated the issue that the camera will disconnected when changing grid layout.
5. [CNB] Fixed the bug thated the issue that the multi stream is disconnected.
6. [Centrix] Fixed the bug thated the issue that the multi stream information is incorrect displayed for generic model.
Titan NVR:
1. [Onvif] Fixed the bug thated the issue that Onvif/Onvif will use first profile for default connecting profile.
39 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
2. [Vitek] Fixed the bug thated UPnP search fail issue.
3. [Hikvision] Fixed the bug thated the issue that the camera parameters are not changed by generic model.
4. [Axis] Fixed the bug thated the issue that the camera will disconnected when changing grid layout.
5. [CNB] Fixed the bug thated the issue that the multi stream is disconnected.
6. [Centrix] Fixed the bug thated the issue that the multi stream information is incorrect displayed for generic model.
NUUO Crystal™:
1. [Onvif] Fixed the bug thated the issue that Onvif/Onvif will use first profile for default connecting profile.
2. [Vitek] Fixed the bug thated UPnP search fail issue.
3. [Hikvision] Fixed the bug thated the issue that the camera parameters are not changed by generic model.
4. [Axis] Fixed the bug thated the issue that the camera will disconnected when changing grid layout.
5. [CNB] Fixed the bug thated the issue that the multi stream is disconnected.
6. [Centrix] Fixed the bug thated the issue that the multi stream information is incorrect displayed for generic model.
Release Version v3.0.1 (2014/02/14)
Modules:
Device Pack v 3.0.1
Supported Systems:
NVRmini 2 v 1.7.1 and above
Bug Fixed the bug thated:
40 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
NVRmini 2:
1. Fixed the bug thated the issue that cannot login web client.
Release Version v3.0.0 (2014/2/5)
Modules:
Device Pack v 3.0.0
Supported Systems:
Mainconsole v 4.1.12 and above*
NVRmini 2 v 1.7.1 and above
NVRsolo
Titan NVR
NUUO Crystal™ v 1.6.2 and above v 2.0.3 and above
Copyright © 2014 NUUO Inc. All rights reserved.
41 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
*For Mainconsole multi stream and setting function, please upgrade to Mainconsole v5.0.0 and above first.
New Camera Supported:
Arecont AV3145 , AV5245 and Generic model
Axis
Dlink
M3025, M3026 and P5415
DCS-6045L
Dynacolor
Eneo
Fine
Samsung
Sony
Sunell
Truen
Vivotek
Zavio
NH720-20N8 and NH820-20N8
PXB-2180Z03, PXC-2080CS and PXC-2080Z03
CDB-HFD720, CDB-MV720F-H, CDV-MD602, CDV-P360-5 (fisheye camera),
TCP-BF128, TCP-HDVB720-H and TCP-MB602
SNB-5003, SNB-5004, SND-5083, SND-5084 and SNV-5084
SNC-EB600, SNC-EB600B, SNC-EB630B, SNC-EM601, SNC-EM602R,
SNC-EM630, SNC-EM631, SNC-EM632R, SNC-VB635, SNC-VM601,
SNC-VM602R, SNC-VM631 and SNC-VM632R
SN-IPR54/31UDN
TN-B200CE, TN-B202CEIR, TN-D1202CE, TN-P1220CS, TN-P1222CGPLX,
TN-P1230CS, TN-P3220CS, TN-P3220CSIR and TN-P3220CTIR
FD8137H, FD8137HV and IP8364
B7510 and D4210
FW upgrade:
Axis
Centrix
Dlink
Eneo
Sony
New Feature:
Mainconsole:
P7210 (FW 5.50.2)
Generic model (FW cx20131107NSA)
DCS-3010, DCS-3714 and DCS-5222LB1(FW : v1.11.00)
PXB-1080Z03, PXB-2080MIR, PXB-2080Z03, PXD-2080MIR and
PXD-2080Z03
(FW 4.23.49-ds)
SNC-EM600, SNC-VB630 and SNC-VM630
42 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
1. Support multi stream setting function with Mainconsole v5.0.0 and above on Axis PQM series,
Arecont all series, Vivotek 8000 series and Samsung SNB-5003, SNB-5004, SND-5083,
SND-5084 and SNV-5084 from DP v3.0.0.
2. Support multi stream function with requested cameras. (please refer to http://www.nuuo.com/SupportCamera.php?node_id=4#4 )
Enhancement:
1. Adjust Samsung camera SNP-3120V, SNP-3430H, SNZ-5200, SPE-100 PTZ speed to 3 or 1.
2. D-Link China camera DCS-V70M-21H, DCS-V70M-21H2 multi-stream: i. ii. iii.
Adjust fps range from 15 to 20.
Adjust 2 nd stream resolution to 640x480.
Adjust 2 nd stream bitrate to 1000kbps.
Notice:
11. Samsung: a. SNB-5003, SNB-5004, SND-5083, SND-5084 and SNV-5084 : i. Support 64 preset points. ii. iii.
Default value of Talk will setup to 5.
When change audio setting on camera web, the previous connection will be interrupted and re-connect. (camera firmware issue)
12. Dynacolor a. NH820-20N8, NH720-20N8 i. ii.
When using MJPEG format, camera reply is slow. (camera firmware issue)
It would not support motion detection when camera resolution is 1920x1080 (Low iii.
Latency). (camera firmware issue)
Camera does not support MJPEG format with 1280x720 (Low Latency). (camera firmware issue)
13. Sunell a. SN-IPR54/31UDN i. Due to Onvif limitation, some framerate and bitrate cannot setup.
14. Fine a. CDV-MD602 i. Motion detection may fail when select 30 fps mode. (camera firmware issue)
15. D-Link a. DCS-3010 i. ii.
Motion detection may fail after setting camera parameter. (camera firmware issue)
Camera may not work when setup bitrate to 8000kbps. (camera firmware issue)
43 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 iii. iv.
Not support dual stream.
The live view may delay when setup high resolution. (camera firmware issue) b. DCS-5222LB1 i. Not support talk. (camera firmware issue) ii. iii.
Not support preset. (camera firmware issue)
Direction of PTZ is opposite. (camera firmware issue) iv. The live view may delay when setup high resolution. (camera firmware issue) c. DCS-3714 i. Not support 8M bitrate. (camera firmware issue) d. DCS-6045L i.
16. Arecont
It may need to reboot again after a period of time. (camera firmware issue) a. Due to camera performance, camera fps may not reach to the frame rate configuration. b. Audio function may not work after connect/disconnect, and need to reboot camera.
17. Eneo a. Only support RTSP port 554 (camera firmware issue) b. Only integrate NTSC mode. c. Audio will be discontinuous under fps 1. d. Camera fps may not reach to camera setting under high resolution, frame rate and quality. e. Not support brightness, contrast, saturation on Mainconsole (camera firmware issue) f. Audio out is not supported with Mainconsole (camera firmware issue)
Bug Fixed the bug thated:
Mainconsole:
14. [Onvif] Fixed the bug thated the issue that causes Mainconsole error when adding cameras
NVRmini 2:
1. [IPPower] Fixed the bug thated the issue that causes live view delay and incorrect camera fps display.
2. [Vivotek] Fixed the bug thated the issue that causes FD8136 dual stream do not display correctly.
3. [RTSP] Fixed the bug thated the issue that CPU loading will increase after audio function turn off.
44 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
NVRsolo:
1. [IPPower] Fixed the bug thated the issue that causes live view delay and incorrect camera fps display.
2. [RTSP] Fixed the bug thated the issue that CPU loading will increase after audio function turn off.
Titan NVR:
1. [IPPower] Fixed the bug thated the issue that causes live view delay and incorrect camera fps display.
2. [Sony] Fixed the bug thated the issue that causes Sony camera to disconnect.
3. [RTSP] Fixed the bug thated the issue that CPU loading will increase after audio function turn off.
NUUO Crystal™:
1. [Sony] Fixed the bug thated the issue that causes Sony camera PTZ speed delay.
2. [IPPower] Fixed the bug thated the issue that causes live view delay and incorrect camera fps display.
3. [RTSP] Fixed the bug thated the issue that CPU loading will increase after audio function turn off.
Release Version v2.20.0 (2013/12/26)
Modules:
45 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Device Pack v 2.20.0
Dynacolor
Fine
Forenix
Hikvision
Messoa
Pelco
Sony
Vivotek
FW upgrade:
Dlink
MegaIP
Santec
Sony
Supported Systems:
Mainconsole v 4.1.12 and above
NVRmini 2 v 1.7.1 and above
NVRsolo
Titan NVR
NUUO Crystal™
New Camera Supported: v 1.6.2 and above
V 2.0.0 and above
Arecont
Aver
Axis
Dlink
DlinkCN
AV2256 and AV2456
FB2027-1, FB2027-2, FB2027-3, FB2028, FB2028-T1, FB2028-T2, FB2028-TM,
FB3027, FB3028-RT1, FB3028-RT2, FB3028-RTM, FD2020, FD3020, FD3020-M
FV2006, FV2028, FV3028, FV3028-RT, FV3028-RTM, FX2000, FX3000-R,
SF2121H-BHR-30, SF2121H-BHR-50 and SF2121H-R
M3024-L, P5414, Q1765-LE, Q6044 and Q6045
DCS-5222LB1
DCS-H41-11D/I and DCS-H41-12D/I
NA083 (fisheye camera)
MD-D3622Q-H, SP-HP2330Q-IP, TCP-336AM, TCP-IRH5080-50 and
TCP-IRH5080-70
IPB-1080BL, IPB-1080BM, IPD-1080CD, IPV-1080CD and IPX-1080DN
DS-2CD7253F-EIZ
NCR858, NCR878, NDF821, NDF821PRO, NDF831, NDF831PRO and
NDR891PRO
D5220, IL10 and IM10
SNC-EB630, SNC-EM600, SNC-VM600 and SNC-VM630
FD8135H, FD8164, FD8164V, SD83x4, SD83x6
DCS-2310L, DCS-2332L and DCS-6010L (FW V1.02.00)
NCD-2003PR and NMX-2003P (FW mega-web-51110.2.1262.100.bin )
SNC-3302, SNC-3322, SNC-4302, SNC-6202, SNC-6302,
SNC-6315IRH and SNC-8322I/HO (firmware_1.0.3.447)
SNC-VB600 (FW 1.9.2)
46 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Enhancement:
3. Add Brickcom FD-301Af and VD-301Af to 50xA model
Notice:
18. IP Power: a. Generic: i.
19. Hikvision:
Focus function does not test with NUUO product. a. DS-2CD7253F-EIZ i. Only supports zoom in/out in the PTZ-control. ii. When resolution is 1600x1200 and 1600x912, the range of framerate does not synchronize with web. iii. iv.
2nd stream format must be the same with main stream except MJPEG.
UPnP search cannot get a valid mac address. (NVRmini 2/NVR Solo/Titan
NVR/NUUO Crystal™)
20. Aver a. MJPEG could not reach to the framerate which user setups. (camera performance issue) b. UPNP search failure when change web port from 80 to others.
21. Sony a. In certain scenarios i.e. under high frame rate or resolution, camera might have limitation. For further information, please visit Sony A&E Portal: https://www.security.sony.biz/ssp/ae/homeDisplay.do
(SNC-EB630, SNC-EM600,
SNC-VB600, SNC-VM600 and SNC-VM630) b. Audio (G726 40kbps, 32kbps, 16kbps) is non-smooth or muted with Titan NVR
(SNC-VB600, SNC-VM600 and SNC-VM630)
22. Messoa a. It takes 10 sec or more to setup parameter setting. b. It will get wrong parameter setting after setup. c. Not support talk. (Mainconsole) d. Not support auto detection. (NVRmini 2/NVR Solo/Titan NVR/NUUO Crystal™)
23. D-Link a. DCS-6010L: i. When finish resolution parameter setting, fisheye setting will random set back to default setting (Mount type: Desktop; Display Mode: 4R). (Mainconsole) b. DCS-2332L, DCS-2310L i. Bitrate List will not change by select different resolution.
47 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
24. Vivotek a. FD8164 i. Brightness and Contrast range from -5 to 5 instead of 0 to 100 in web. (camera firmware issue) b. SD8316E i. Brightness and Contrast range from -5 to 5 instead of 0 to 100 in web. (camera firmware issue) c. FD8135H i. ii.
Resolution list does not synchronize with the list on web. (camera firmware issue)
When format is setup to MPEG4, resolution is 1280 x 800 and quality is best, the maximum FPS can only reach 20. (NVRmini 2/NVR Solo/Titan NVR/NUUO Crystal
™ ) (camera firmware issue)
25. Fine a. MD-D3622Q-H: i. When use Pan speed bar to control Pan speed, Tilt speed will be the same.
(Mainconsole) b. TCP-336AM: i. When format is MPEG4, resolution is 1920 x 1080 and quality is excellent, the maximum FPS can only reach 20.
26. Pelco a. D5220 i. Preset point name cannot change, and will not synchronize with camera web.
(Mainconsole) ii. iii.
Video parameter (brightness, contrast, saturation) will not synchronize with camera web. (Mainconsole)
When resolution or quality is high, framerate would not reach its setting.
(Mainconsole) iv. It may cause Mainconsole unstable when change protocol. (UDP->HTTP,
HTTP->UDP) b. IM10 and D5220 i. It will need to disable second profile on web first and parameter setting can be changed.
27. MegaIP a. Getting bitrate value would not synchronize with camera web. (Camera onvif issue) b. Setting quality value would not synchronize with camera web. (Camera onvif issue) c. After setting parameter on camera, camera would restart. After it completed, then can get parameter setting.
48 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 d. Only when http port is 80, motion detection and DI/DO can work.
Bug Fixed the bug thated:
Mainconsole:
1. [D-Link] Fixed the bug thated VBR setting issue.
NVRmini 2:
1. [Fine] Fixed the bug thated the issue that TCP-HFB1080D does not support UPnP.
2. [Samsung] Adjusted SNP-5300 PTZ default speed to 3.
3. [Sony] Fixed the bug thated the issue that all Sony cameras might disconnect.
NVRsolo:
1. [Fine] Fixed the bug thated the issue that TCP-HFB1080D does not support UPnP.
2. [Samsung] Adjusted SNP-5300 PTZ default speed to 3
3. [Sony] Fixed the bug thated the issue that all Sony cameras might disconnect.
Titan NVR:
1. [Fine] Fixed the bug thated the issue that TCP-HFB1080D does not support UPnP.
2. [Sony] Fixed the bug thated the issue that all Sony cameras might disconnect.
3. [Samsung] Adjusted SNP-5300 PTZ default speed to 3
NUUO Crystal™:
1. [Sony] Fixed the bug thated the issue that all Sony cameras might disconnect.
Release Version v2.19.0 (2013/11/26)
Modules:
49 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Device Pack v 2.19.0
Supported Systems:
Mainconsole v 4.1.12 and above
NVRmini 2 v 1.7.1 and above
NVRsolo
Titan NVR v 1.6.2 and above
New Camera Supported:
3Svision N1011, N1012, N1031, N1032, N3011, N3012, N3031, N3032, N6011,
N6012 ,N6013, N6014, N6015, N6016, N6031, N6032, N6033, N6034, N6035,
Arecont
Axis
DigitalWatchdog
Dlink
Fine
Hikvision
N6036, N6037, N6038, N8011, N8012, N8031, N8032, N9012, N9032, N9033 and N9034
AV5455DN-F, AV3456DN-F
M2014
DWC-MD421 and DWC-MV421
DCS-2330L, DCS-2132LB1, DCS-3714, DCS-5615 and DCS-7110B1
TCP-HFB1080D
DS-2CD2612F-IS, DS-2CD2632F-IS, DS-2CD2712F-IS and DS-2CD2732F-IS i-Mege
IP Power
Mobotix
Neovista
RIVA
Sunell
Vivotek
Zavio
FW upgrade:
G1102E
Generic
D15D-Sec, D15D-Sec-DNight, D15D-Sec-Night-Pano, D15D-Sec-Pano,
Generic, M15D-Sec, M15D-Sec-DNight, M15M-Sec, S14D-Sec,
S14D-Sec-Night, S14M-Sec, S15D-Sec, S15M-Sec and S15M-Sec-Night
NV-CB1-36, NV-DP1RP-3312-15, NV-CB1R-36-6, NV-CB1RW-36-6,
NV-CB3PL-28, NV-CB3WL-28, NV-DM1P-28, NV-BT3RP-3105-30 and
NV-PT13RP-4-15
RC1100, RC1100M, RC1202HD, RC2100M, RC2102HD, RC302HD, RC3100,
RC3102HD, RC3203HD, RC3302, RC3500, RC3500M, RC3502HD,
RC3502HDIR, RC3702, RC4100, RC5500, RC5510, RC6500, RC6602HD,
RC6700, RC6802HD, RCC100HD, RE1000 and RE4000
SN-VSR54/04
IP8173H, IP8337H and IP8336W
V1100
50 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ATV
Santec
Hikvision
IPFD2MT (FW HSNCT3-v2.1.71)
SNC-3305, SNC-5312IR, SNC-5315IR, SNC-6212IR, SNC-6312IRH,
SNC-6315IRH (firmware_1.0.2.386)
DS-2CD7153-E
Enhancement:
1. Add Brickcom OB-300-NP-AD with zoom and focus to 30xN model
2. Add Brickcom OSD-200 to 20xP model
Notice:
1. IP Power: a. Generic: i. Focus function is not test on NUUO product. ii. iii.
The maximum resolution is depends on camera.
Some framerate and bitrate cannot setup due to Onvif restriction.
2. i-Mege: a. G1102E : i. ii. iii.
3. Mobotix:
No support on-edge motion when video format is MJPEG.
Support UPnP Search after Mainconsole v4.1.18.
Camera connection is not stable. (firmware issue) a. D15D-Sec, D15D-Sec-DNight, D15D-Sec-Night-Pano, D15D-Sec-Pano, M15D-Sec,
M15D-Sec-DNight, M15M-Sec, S14D-Sec, S14D-Sec-Night, S14M-Sec, S15D-Sec, i.
S15M-Sec and S15M-Sec-Night
Please setup on Mobotix web setting page first for display mode, ExtIO and ii.
4. Hikvision: on-edge motion.
Not support audio when video format is MJPEG. a. DS-2CD2732F i. When resolution is 2048x1536, the range of framerate does not synchronize with web. b. DS-2CD7153-E i. When resolution is 1600x1200, the range of framerate does not synchronize with web.
Except MJPEG, 2nd stream format will be the same as main stream format. ii.
5. Santec:
51 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 a. SNC-3305, SNC-5312IR, SNC-5315IR, SNC-6212IR, SNC-6312IRH, SNC-6315IRH i. When resolution is 2048x1536 and PAL mode, the range of framerate does not ii. iii. synchronize with web.
With high resolution there is noise with audio.
The bitrate of 2nd stream, minimum mode, is 200Kbps. (firmware issue)
6. Sunell: a. Audio only available on channel 1 and channel 2. b. DI2 cannot work correctly.
7. Fine: a. The response of camera setting is slow. b. Not support UPnP search on NVRmini 2, NVRsolo and Titan NVR.
8. Zavio: a. Audio in/out does not support AMR.
9. D-Link: a. DCS-2132LB1 and DCS-2330L do not support TCP/UDP. (firmware issue) b. DCS-2330L does not support talk. (firmware issue)
Bug Fixed the bug thated:
Mainconsole:
1. [Onvif/Onvif] Fixed the bug thated the issue that Mainconsole will dump when connecting.
2. [Santec] Fixed the bug thated the issue that SNC-4302, SNC-8322I/HO, SNC-3322 will dump when connecting.
3. [Fine] Fixed the bug thated the issue that TCP-MH859 does not support MJPEG with resolution 2048x1536 and 2592x1944.
4. [Vivotek] Fixed the bug thated multicast stream issue.
5. [Axis] Fixed the bug thated the issue that P8221 output cannot work.
NVRmini 2:
1. [Fine] Fixed the bug thated the issue that TCP-MH859 does not support MJPEG with resolution 2048x1536 and 2592x1944.
2. [Vivotek] Fixed the bug thated multicast stream issue.
3. [Axis] Fixed the bug thated M3007 unable to connect issue.
4. [Axis] Fixed the bug thated the issue that P8221 output cannot work.
NVRsolo:
1. [Fine] Fixed the bug thated the issue that TCP-MH859 does not support MJPEG with resolution 2048x1536 and 2592x1944.
52 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
2. [Vivotek] Fixed the bug thated multicast stream issue.
3. [Axis] Fixed the bug thated M3007 unable to connect issue.
4. [Axis] Fixed the bug thated the issue that P8221 output cannot work.
Titan NVR:
1. [DynaColor] Fixed the bug thated the issue that Live View shows “No Data” on the iViewer issue.
2. [Hikvision] Fixed the bug thated the issue that Generic model motion does not work issue.
3. [Fine] Fixed the bug thated the issue that TCP-MH859 does not support MJPEG with resolution 2048x1536 and 2592x1944.
4. [Vivotek] Fixed the bug thated multicast stream issue.
5. [Axis] Fixed the bug thated M3007 unable to connect issue.
6. [Axis] Fixed the bug thated the issue that P8221 output cannot work.
Release Version v2.18.0 (2013/10/28)
Modules:
Device Pack v 2.18.0
53 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Supported Systems:
Mainconsole v 4.1.12 and above
NVRmini 2 v 1.7.1 and above
NVRsolo
Titan NVR v 1.6.2 and above
New Camera Supported:
Arecont
ATV
AV2455DN-F
HDG-M120 and IPFD2MT
Brickcom
Dlink
DlinkCN
Eneo
Etrovision
Fine
Forenix
Hikvision
Honeywell
Levelone
Panasonic
Samsung
Vivotek
MD-300Np-360 and MD-500Ap-360 (fisheye camera)
DCS-940L
DCS-V70M-21H2
PXB-2080MIR, PXD-2080MIR and PXD-2080Z03
EV8582U-BL, N51A-ML, N50U-ML, N51U-ML and N71U-ML
TCP-MH859
FBX-200CL, FBU-201LWD and FDM-200LWD
DS-2CD2212-I3, DS-2CD2612F-I, DS-2CD2712F-I
H3D1F and H3D2F
WCS-0050
DG-SC385
SNF-7010 (fisheye camera) and SND-3082
IP8371E
FW upgrade:
Forenix
Hikvision
Sony
DlinkCN
Everfocus
Zavio
FBU-200LWD, FBX-200LWD and FVD-200LWD
DS-2CD2112-(I), DS-2CD2212-I5 and DS-2CD2312-I (FW 5.0.2)
SNC-CH120 (FW 1.80)
DCS-N40M-22H3, DCS-V40M-12H, DCS-N70M-21H3,
DCS-N31M-21H3 DCS-V40M-32H2, DCS-V70M-11H and
DCS-V70M-21H2 (VB1.0.29)
EDN1220 and EDN1320 (FW 1.0.8)
B7320 (FW M3.1.5.17)
54 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Notice:
1. EverFocus: a. EDN1220, EDN1320: Not support Mpeg4 (Firmware issue) b. EDN1320: Not support 160x128 in profile3 (Firmware issue)
2. Fine: a. TCP-MH859: Not support M-Jpeg with resolution 2048x1536 and 2592x1944.
3. ATV: a. HDG-M120: Does not implement Audio-out (Talk) b. HDG-M120: UPNP search failure if changed web port 80 to others c. HDG-M120: Not support UDP connection d. HDG-M120: Camera reply slowly if set maximum video parameters e. HDG-M120: The bitrate of stream 3 setup will fail at 100 kbps, but work at 200 kbps. f. IPFD2MT: Not support UPNP search g. IPFD2MT: MJPEG could not setup 1280x1024 and 1280x720 resolution at web, but camera still reply OK.
4. Hikvision: a. DS-2CD2012-I: Sub stream resolution must be smaller than Main stream resolution.
5. Sony: a. SNC-CH120: Not support SolidPTZ mode
6. Brickcom: a. 30xN: It does not support talk, IO on MD-300Np-360. b. 30xN: It does not support MD when format is MJPEG and MPEG4 on MD-300Np-360. c. 50xA: It does not support talk on MD-500Ap-360 d. 50xA: It does not support MD when format is MJPEG and MPEG4 on MD-500Ap-360.
7. Forenix: a. It does not support UPnP and auto detection. b. Camera will crash if open camera web under win XP. c. The setting of brightness was wrong via CGI command. It will sync setting of grayscale. d. The sound is weak with audio under format G.726.
8. Etrovision: a. N71U-ML, N50U-ML, N51U-ML and N50A-ML i. Only support focus and zoom. ii. iii. iv. v.
It is noise with audio.
Only support motion under H.264.
Not support talk.
Dual stream will disconnect if main stream sets MPEG4, 1080P and FPS over 20. b. EV8582U-BL
55 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 i. Only support motion under H.264.
9. Zavio: a. Not support audio in.
10. Arecont: a. AV2455DN (fw65220) would reboot after connecting DO port. b. AV2455DN (fw65220) cannot reach 30fps due to camera performance issue.
11. Honeywell: a. H3D2F: Only support Zoom and Focus, not support Pan and Tile. (Mainconsole) b. H3D2F: Only support Zoom, not support Pan and Tile. (NVRmini 2, NVRsolo, Titan NVR)
Bug Fixed the bug thated:
Mainconsole:
1. [Onvif/Onvif] Fixed the bug that the issue that it will cause Mainconsole crash when get incorrect preset name.
2. [DLinkCN] Fixed the bug that the issue that it will not work on Pan, tilt with DCS-H90-31D2.
3. [D-Link] Fixed the bug that DI/DO fail issue with DCS-6915.
4. [Hikvision] Fixed the bug that the issue that it will cause crash when get incorrect RTSP video packet.
NVRmini 2:
1. [D-Link] Fixed the bug that dual stream disconnect issue on DCS-5010L.
2. [Samsung] Fixed the bug that the issue that the motion detection does not work on
SNO-7082.
3. [Vivovtek] Fixed the bug that VS8801 dual stream incorrect channel display issue.
4. [Axis] Fixed the bug that P5532-E dual stream disconnect issue.
5. [Hikvision] Fixed the bug that the issue that it will cause crash when get incorrect RTSP video packet issue.
NVRsolo:
1. [Samsung] Fixed the bug that the issue that the motion detection does not work on
SNO-7082.
2. [Vivovtek] Fixed the bug that VS8801 dual stream incorrect channel display issue.
3. [Axis] Fixed the bug that P5532-E dual stream disconnect issue.
4. [Hikvision] Fixed the bug that the issue that it will cause crash when get incorrect RTSP video packet issue.
56 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Titan NVR:
1. [Fine] Fixed the bug that dual stream disconnect on WB-H814 issue.
2. [Samsung] Fixed the bug that the issue that the motion detection does not work on
SNO-7082.
3. [Vivovtek] Fixed the bug that VS8801 dual stream incorrect channel display issue.
4. [Axis] Fixed the bug that P5532-E dual stream disconnect issue.
5. [Hikvision] Fixed the bug that the issue that it will cause crash when get incorrect RTSP video packet issue.
57 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.17.1 (2013/09/30)
Modules:
Device Pack v 2.17.1
Supported Systems:
NVRmini 2 v 1.7.1 and above
Titan NVR
Bug Fixed the bug thated:
NVRmini 2: v 1.6.2 and above
2. Fixed the bug that that ACTi camera dump issue.
NVRSolo:
1. Fixed the bug that that ACTi camera dump issue.
Titan NVR:
1. Fixed the bug that that ACTi camera dump issue.
Copyright © 2014 NUUO Inc. All rights reserved.
58 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.17.0 (2013/09/26)
Modules:
Device Pack v 2.17.0
Supported Systems:
Mainconsole v 4.1.12 and above
NVRmini 2 v 1.7.1 and above
NVRsolo
Titan NVR v 1.6.2 and above
New Camera Supported:
Axis
Dlink
M7010, P1214, P3353 and Q7411
DCS-7413 B1
DlinkCN
InscapeData
Levelone
Panasonic
DCS-N20M-10H2, DCS-N30M-51H2, DCS-N40M-53H2, DCS-N70M-20H2,
DCS-N40M-32H2, DCS-V30M-50H, DCS-V30M-51H, DCS-V40M-32H,
DCS-V40M-33H, DCS-V70M-20H, DCS-V70M-21H, DCS-V70M-50H and
DCS-N70M-50H2
NVC3033H-DN and NVC360H-DN-IR
FCS-5061, FCS-3101 and FCS-4101
BB-ST162, BB-SW172, BL-VT104W, BL-VP164W, DG-SF132, DG-SP102 and
WV-SF438 (fisheye camera)
SNP-5300, SNP-6200RH
SNC-CX600W, SNC-VB600B, SNC-VM600B and Generic
IP8130, IP8130W, IP8131, IP8131W and SD8363E
Samsung
Sony
Vivotek
FW upgrade:
Arecont
Dlink
Panasonic
AV1115, AV1125, AV1145, AV1255, AV2115, AV3115, , AV3125,
AV5125, AV10115, AV10255 (FW 65218), AV3116 (FW 65219),
AV5155 (FW 65152), AV8365, AV20185 and AV20365 (FW 65183)
DCS-2310L (FW v1.01.10)
WV-SF132, WV-SP102 (1 Application: 1.81, 2 Image date:1.03),
WV-ST162, WV-SW172 (1 Application: 1.81, 2 Image data: 1.04)
59 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Sony
Vision Hitech
SNC-VB630 (FW 1.7.0)
Vision M3i (FW 1.1.2.46), Vision SM3Ti (FW1.1.4.1 20130816) and
Vision Mi(FW 1.1.2.46)
Notice:
1. Feature added: a. Support Samsung camera search tool.
Testing model:
1. SNB-3002 / SND-3082/F / SNV-3082
2. SNB-7002 / SND-7082/F / SNV-7082 / SNO-7082R
3. SNV5080R
4. SNO5080R
5. SNB-5000A / SND5080F / SNV5080
6. SNP-5300
7. SNP-6200RH b. Dual Stream default format change to H.264 for Arecont camera and Vivotek camera. c. For Mini2/Solo/Titan, Arecont cameras do not use TFTP to get stream. Always use RTSP or HTTP method to get stream. d. Samsung dual stream structure changed. When main stream format is H264, dual stream format will be MJPEG. When main stream format is MJPEG, dual stream format will be H264.
2. Known issue: a. It cannot use G726 16kbps on Panasonic talk function. b. VisionHitech
1. VISION M3Ti i. ii.
It can not use Autofocus function. (camera firmware issue)
It will not support audio setup. (camera firmware issue)
2. VISION M3i i. It can not support Quality with MJPEG. (camera firmware issue) ii. The real FPS could not reach original value on Web when setup maximum setting of camera parameters, for example setting is H.264 within 1920x1080, 30 fps, and 7 quality but can get 15 fps only; setting is MJPEG within 1280x720, 30fps but can get 5~6 fps only.
3. VISION Mi i. It will not support audio setup. (camera firmware issue) ii. It can not support Quality with MJPEG. (camera firmware issue)
60 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 iii. The real FPS could not reach original value on Web when setup maximum setting of camera parameters, for example setting is H.264 within 1920x1080, 30 fps, and 7 quality but can get 15 fps only; setting is MJPEG within 1280x720, 30fps but can get 5~6 fps only. c. Levelone
1. FCS-3101 and FCS-4101 i. i.
Not support video parameter. (camera firmware issue)
Not support bitrate 20Kbps.
2. FCS-5061 i. It will have talk audio with noise under win XP system issue. ii. With the maximum value of video settings (fps, bitrate) change protocol will cause MainConsole crash. d. Arecont
1. When use firmware 65218 Arecont camera needs to be used in close-network.
2. Arecont camera might not meet the frame setting due to camera performance.
3. Arecont camera’s dual stream bitrate might be larger than 500kbps due to high resolution.
Bug Fixed the bug thated:
Mainconsole:
1. Fixed the bug that that RTSP timeout causes Samsung camera disconnect issue.
2. Fixed the bug that that Panasonic BL-VT164 cannot use PTZ issue.
3. Fixed the bug that that DynaColor V6 disconnect issue.
4. Fixed the bug that that Zavio P5111, P5116, P5210 PTZ speed range is not synchronize between camera setting and web.
NVRmini 2:
1. Fixed the bug that that RTSP timeout causes Samsung camera disconnect issue.
Titan NVR:
1. Fixed the bug that that Samsung SNP-3302/H cannot use PTZ issue.
2. Fixed the bug that that Hikvision Generic cannot use focus function issue.
3. Fixed the bug that the issue that original stream will disconnect when switch between original and low/minimized stream.
61 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.16.0 (2013/08/26)
Modules:
Device Pack v 2.16.0
Supported Systems:
Mainconsole v 4.1.12 and above
NVRmini 2 v 1.7.1 and above
NVRsolo
Titan NVR v 1.6.2 and above
New Camera Supported:
3S
Arecont
N5012
AV2255AM and AV5255AM
Bosch
Dlink
DlinkCN
Eneo
Grundig
Milesight
NBC-225-P, NDC-225-PI, NBC-255-P, NDC-255-P, NTC-255-PI, NBC-265-P,
NDC-265-P, NDN-265-PIO, NBC-274-P, NBC-274-PT and NBC-274-PM
DCS-6004L, DCS-6005L
DCS-H70-21D/M
PXB-2080Z03 and PXD-2080Z03
GCI-H2505B, GCI-K0589T(H), GCI-K0779P, GCI-K1523VS, GCI-K1526VS,
GCI-K1585V, GCI-K1586V and GCI-K2505B
MS-C2351, MS-C2361, MS-C2362, MS-C2372, MS-C2451, MS-C2471,
Panasonic
Samsung
Sunell
Vivotek
MS-C2651, MS-C2661, MS-C2662, MS-C2671, MS-C2672, MS-C2681,
MS-C2682, MS-C2951, MS-C3351, MS-C3356, MS-C3361, MS-C3362,
MS-C3366, MS-C3372, MS-C3376, MS-C3651, MS-C3656, MS-C3658,
MS-C3661, MS-C3662, MS-C3666, MS-C3671, MS-C3672, MS-C3673,
MS-C3676, MS-C3678, MS-C3681 and MS-C3682
BL-VP101, BL-VP104 and BL-VT164
SNO-6084 and SNV-6084
Generic model
AF5127, AF5127V, SF8172, SF8172V, FE8172V (the above models are fisheye camera . SF8172 and SF8172V support PPTZ), AB5353H
62 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
FW upgrade:
Arecont
CNB
Dlink
Everfocus
Samsung
Sunell
AV1255 (FW 65218), AV3255 (FW 65218), AV5115DN (FW 65218),
AV8185DN (FW 65183) and AV8365DN (FW 65183)
IDC 4000T(FW T1-1.0.13.0424) and INS 2000 (FW
XNET.A1-2.01.13.0204)
DCS-2103 (FW 1.20), DCS-2130 (FW 1.20), DCS-2210 (FW 1.20) and
DCS-2230 (FW 1.20)
EVS-410 (Firmware upgrade to v1.0.21)
SND-3082, SND-3082/F and SNB-3002
(snb3002_Series_2.10_130416), SNV-5080R (FW snv5080r_3.10_130416), SNO-5080R (FW snb5000_Series_3.10_130416) and SND-5080F, SNB-5000A and
SNV-5080 (FW snb5000_Series_3.10_130416) and SNB-7002,
SNV-7082, SND7082/F and SNO-7082R (FW snb7002_series_1.06_130402), SNB-6003, SNB-6004, and SND-6083
(FW snb6004_Series_1.00_130412)
IPS54-70DN-ZR18, SN-IPC54-40EDN and SN-IPD54-12VDN
Enhancement:
1. Samsung: For SNP-5200 and SNP-6200 change the default speed to 3 or 4.
Notice:
1. Feature added: a. Dual Stream default format change to H.264 for Axis MPQ series camera, Vivotek Generic model and new supported camera above (except support by design camera).
2. Known issue: e. For Samsung SNB-7002, SNV-7082, SND7082/F and SNO-7082R, it will have no image issue via RTSP when Frame rate sets to 1. f. For Samsung SND-3082, SND-3082/F and SNB-3002, it cannot setup video parameter: brightness.
63 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 g. For Samsung SNB-7002, SNV-7082, SND7082/F and SNO-7082R, the resolution will be
800*448 & 320*176 when sets to 800*450 & 320*180. h. For Samsung all cameras: Video GOP appear as 1 ~15, but the value actually will be 1 ~149 in web. i. For Everfocus EVS410
1. It can setup MJPEG high resolution only up to 10 fps.
2. Not support RS-485 PTZ. j. For Sunell Generic
1. Focus, Talk function are not test with NUUO product.
2. The maximum resolution is depending on camera.
3. It cannot set some framerate and bitrate due to Onvif limitation.
4. Camera firmwave must be v1.6_build044014_148 or above then can use generic model. k. For Grundig GCI-K1586V, GCI-K0779P, GCI-K2505B
1. It will have audio noise issue when camera resolution is 1920x1080 or Q factor is 70.
2. It will fail when Get camera parameter resolution is 1920x1080 or Q factor is 70.
3. GCI-K2505B framerate setting will fail when select TV system Autoir option WDR 25fps, autoir25fps and WDR 30fps. l. For CNB INS2000
1. Not support Digital input(DI). (camera firmware issue)
2. Dual stream format could be MJPEG, MPEG4 or H.264. It will be same as main stream format
For CNB IDC4000T
1. It will show incorrect bitrate "1M" when sets Video MPEG with CBR in 4000 bitrate on camera web.
2. It will trigger DO simultaneously when trigger DI.
3. Dual stream default format is MPEG4. m. For D-Link DCS-2103
1. It will not support Talk function on camera web and MainConsole. (camera firmware issue) n. For Milesight MS-C2351, MS-C2361, MS-C2362, MS-C2372, MS-C2451, MS-C2471,
MS-C2651, MS-C2661, MS-C2662, MS-C2671, MS-C2672, MS-C2681, MS-C2682,
MS-C2951, MS-C3351, MS-C3356, MS-C3361, MS-C3362, MS-C3366, MS-C3372,
64 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
MS-C3376, MS-C3651, MS-C3656, MS-C3658, MS-C3661, MS-C3662, MS-C3666,
MS-C3671, MS-C3672, MS-C3673, MS-C3676, MS-C3678, MS-C3681 and MS-C3682 FW issue:
1. It cannot use RateControl.
2. It cannot trigger Motion and DI in the same time.
3. It will have no response when send cgi commend.
4. It will not support UPnP.
5. There is one level of difference between video parameter and camera web on
Mainconsole. o. For Milesight MS-C3651
1. It will not support Digital input(DI). (camera firmware issue) p. For Milesight MS-C3658
1. It will show wrong frame rate value on Mainconsole when change resolution from
2560x1920 to other resolution. q. For 3SVision N5012
1. It will always show HTTP port 80 when use UPnP search. r. For Arecont models
1. AV5155, AV5255, AV2255 need to be connected in close-network. It will operate abnormally in open-network.
2. AV5255, AV2255 not support audio function due to camera firmware issue.
3. AV5255, AV2255 will have broken image when use H264 (TCP/UDP) with high bitrate setting (>16384).
4. AV8185DN and AV8365DN
Four channels need to use the same protocol and format.
The image will flash when the main stream is MJPEG and use dual stream. s. For Vivotek SF8172 and SF8172V
1. Due to camera CPU decode performance issue, the first 1080p stream can reach up to
30 fps, but the second 1080p stream cannot.
Bug Fixed the bug thated:
Mainconsole:
65 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
5. Onvif: Fixed the bug that the issue that enable auto reboot, sometimes it does not start the recording schedule.
NVRmini 2:
1. Vivotek: Fixed the bug that FE8172V auto detect issue.
Titan NVR:
4. Fixed the bug that the issue that Generic RTSP model will disconnect in NuClient live view but it is still recording.
5. Fixed the bug that the issue when reboot Titan NVR, the IP cameras will disconnect and do not record.
66 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.15.0 (2013/07/29)
Modules:
Device Pack v 2.15.0
Supported Systems:
Mainconsole v 4.1.12 and above
NVRmini 2 v 1.7.0 and above
NVRsolo
Titan NVR v 1.6.1 and above
New Camera Supported:
Dlink DCS-3511, DCS-3530, DCS-5010L, DCS-5020L, DCS-5211L, DCS-5222L, and
DCS-6314
DlinkCN
Eneo
Forenix
LG
Sony
DCS-H70-21D/M
PXB-1080Z03, PXB-2080Z03IR and PXB-3080Z20
C2002, C2002-W, D2000-FD3, D2000-VD3, D2000-VP2, FBU-200LWD,
FBU-300LWD, FDM-300LWD, FVD-200LWD, FVD-200LWD, FVD-300LWD,
T2000-FB1, T2000-FB2, T2000-VB3, VQ2100, VQ2200, VQ2210C, VQ2300 and
VQ2310
LND7300, LNP2810T, LNU5100R, LNV5100R and LNV7300
SNC-ER585
Vitek VT-20VN-M, VTC-IR401, VTC-IR402, VTD-134FNIB, VTD-134FNIBP,
VTD-134FNIWP, VTD-13FN, VTD-13V210NIB, VTD-13V210NIBP,
VTD-13V210NIW, VTD-13V210NIWP, VTD-20V210NIB, VTD-20V210NIBP,
VTD-20V210NIW, VTD-MV13V210NBP, VTD-MV13V210NP,
VTD-MV13VR210NBP, VTD-MV13VR210NP, VTD-MV20V210NBP,
VTD-MV20V210NP, VTD-MV20VR210NBP, VTD-MV20VR210NP, VT-PTZ220 and VT-PTZ220NP
67 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Vivotek
Zavio
3M
FW upgrade:
ACTi
Arecont
Dynacolor
Everfocus
Fine
Grandstream
Vivotek
Zavio
FD8133V, FD8166 and FE8173 (fisheye camera)
D7510
ANPR
ACD2000Q (FW v3.04.06-AC), KCM-3911 and KCM-7911 (FW 5.10.02)
AV2115DN (FW 65218) and AV3116DN (FW 65219)
Nv223 (add motorize zoom function detect) (FW z120130417NSA)
EHN3260 (v1.2.2)
CDV-2M360(VB1.0.32_F, fisheye camera),
CDV-5VM501(HD_VC1.0.18_F) and TCP-HDVB800(VC1.0.18)
GXV-3501 (add preset function on Mainconsole)
VS8401 (add dual stream) (0201b)
P5111 and P5116 (M2.1.6.02)
Notice:
3. Feature added: b. Add preset function on Grandstream GXV3501/GXV3504.
4. Known issue: t. Fine
1. CDV-5VM501 i. It will have Image broken issue with MJPEG in 2592x1944 and 2048x2048 via ii.
RTSP
Unstable stream with H.264 via RTSP u. Sony SNC-ER585
It will have image broken issue with MPEG4 texture during resolution switch. (Titan NVR) v. ACTi ACD2000Q
1. Not support framerate 8 due to camera firmware issue. w. Eneo PXD-2080Z03IR
1. Only support RTSP port 554 due to camera firmware issue.
2. Only integrate NTSC mode due to camera firmware issue.
3. It will have discontinuous issue on audio when fps under 1.
68 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
4. Camera framerate may not enough under high resolution, framerate and quality settings.
5. Not support brightness, contrast and saturation due to camera firmware issue.(IP+) x. Vitek
1. VTC-IR401, VTC-IR402 i. Only support RTSP port 554 due to camera firmware issue. ii. iii. iv.
Only integrate NTSC mode due to camera firmware issue.
It will have discontinuous issue on audio when fps under 1.
Camera framerate may not enough under high resolution, framerate and quality settings. v. vi.
Not support UPnP due to camera firmware issue.
Not support brightness, contrast and saturation due to camera firmware issue.(IP+)
2. VTD-13FN, VT-20VN-M, VTD-134FNIB, VTD-134FNIBP, VTD-134FNIWP, VTD-13FN,
VTD-13V210NIB, VTD-13V210NIBP, VTD-13V210NIW, VTD-13V210NIWP,
VTD-20V210NIB, VTD-20V210NIBP, VTD-20V210NIW, VTD-MV13V210NBP,
VTD-MV13V210NP, VTD-MV13VR210NBP, VTD-MV13VR210NP, VTD-MV20V210NBP,
VTD-MV20V210NP, VTD-MV20VR210NBP and VTD-MV20VR210NP i. ii. iii.
Only support RTSP port 554 due to camera firmware issue.
Only integrate NTSC mode due to camera firmware issue.
Camera framerate may not enough under high resolution, framerate and quality settings. iv. v.
Not support UPnP due to camera firmware issue.
Not support brightness, contrast, saturation due to camera firmware issue.(IP+)
3. VT-PTZ220NP and VT-PTZ220 i. Only support RTSP port 554 due to camera firmware issue. ii. iii.
Only integrate NTSC mode due to camera firmware issue.
Camera framerate may not enough under high resolution, framerate and quality settings.
It will have discontinuous issue on audio when fps under 1. iv. v. vi.
Not support UPnP due to camera firmware issue
Preset, preset name and PTZ speed cannot synchronize to camera web due to camera firmware issue.
Not support brightness, contrast and saturation due to camera firmware vii. issue.(IP+) y. 3M
1. ANPR only integrate MJPEG 1 st stream video.
69 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 z. Zavio
1. D7510 i. It will only support framerate 1~15. ii. It will cause delayed image and broken voice when connect stream via RTSP over
HTTP in high video quality.
2. P5116 and P5111 i. It will only support pan and tilt when use PTZ. ii. iii.
It will not support audio when use AMR 7.95 format.
The max framerate of MPEG4 and MJPEG is up to 20 FPS in 1280x800.
Bug Fixed the bug thated:
Mainconsole:
1. Fixed the bug that UDP NVC 1000 will disconnect randomly and show “connecting” all the time.
2. Fixed the bug that when click PTZ focus panel cause terminate abnormal issue.
3. Fixed the bug that terminate abnormal issue when use Onvif null-pointer.
NVRmini 2:
2. Fixed the bug that terminate abnormal when use Onvif null-pointer.
3. Fixed the bug that no video display by setting MJPEG and MPEG4 format with Vivotek
FD8135H.
NVRsolo:
1. Fixed the bug that cannot connect to Eneo PXD-1020F02 issue.
2. Fixed the bug that when connect Santec SNC-3302, SNC-5312, SNC-5315, SNC-6202,
SNC-6212IR and SNC-6312IRH will cause solo crash issue.
3. Fixed the bug that terminate abnormal when use Onvif null-pointer.
4. Fixed the bug that no video display by setting MJPEG and MPEG4 format with Vivotek
FD8135H.
Titan NVR:
6. It will cause system terminate abnormal when connect with Bosch NTC 265PI/NDN-265PIO.
7. Fixed the bug that cannot connect Honeywell HDEZ20HDEX (firmware H20120808NSA) issue.
8. Fixed the bug that terminate abnormal when use Onvif null-pointer.
9. Fixed the bug that no video display by setting MJPEG and MPEG4 format with Vivotek
FD8135H.
70 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.14.0 (2013/06/26)
Modules:
Device Pack v 2.14.0
Supported Systems:
Mainconsole v 4.1.0 and above
NVRmini 2 v 1.5.0 and above
NVRsolo
Titan NVR v 1.3.0 and above
New Camera Supported:
ACTi
Arecont
D61, E25, E66 and KCM8211
AV12186
Brickcom
DigitalWatchdog
Dlink
Everfocus
20xp and 300N series
DWC-MPA20M
DCS-6115, DCS-6315, Super Model
EMN 2320 and ETN 2110
Fine
Samsung
Vivotek
Zavio
C3000/C3000-W, CDV-3VM800, CDB-5VM551, CDB-MV1080F
TCP-HP1080 and TCP-VM359
SNB-6003, SNB-6004, SND-6083 and SND-6084
FD8363, FD8163 and Generic
B7320 and F3210
FW upgrade:
71 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi
Vivotek
D11, D12, D21, D22, D31, D32, D41, D42, D51, D52, D54, D55, D62,
D64, D65, D71, D72, D81, D82, E11, E12, E13, E21, E22, E23, E24,
E26, E31, E32, E33, E34, E41, E42, E43, E44, E45, E46, E51, E52, E53,
E54, E55, E56, E61, E62, E63, E64, E65, E67, E71, E72 ,E73, E74, E81,
E82, E83, E84, E85, E86, E87, E91 ,E92 (FW 6.03.17) and
KCM8111(FW 5.10.02)
FD8161 (FW 0105b)
Notice:
5. Known issue: c. ACTi
For D and E series camera
Fixed the bug that the Fragment IP assembly timer handler panic to reboot.
E13 and the certificate
It will disconnect with NUUO product abnormally.
E84 and the certificate
If select resolution 640x360, it will have incorrect value on parameter setting. d. Samsung SND-6083
The talk from the speaker is weak. e. Fine
CDB-5VM551
Not support MJPEG with resolution 2592x1944.
CDV-3VM800
It will cause image broken, and drop frame when use MJPEG with highest fps, resolution and quality through TCP connection.
It will cause CPU heavy loading when use MJPEG with highest fps, resolution and quality through RTSP.
TCP-HP1080
Received only half of fps with web setting f. Digital watchdog
Not support dual stream when select single stream for ONVIF setting at webpage.
There is a valid resolution 320x0 in profile1 at MJPEG.
72 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
The quality value does not synchronize with webpage quality value.
It is invalid with frame rate 0.
There are two port settings on camera web, web port and service port. When NUUO product and camera are located in the same network, you can use this web port as configuring port on NUUO product. If NUUO product and camera are located in different network, you must choose service port. "Go to web" function on NUUO product setting page might direct to the wrong url. g. D-Link
Super Model (Tested by DCS-2332L)
It is incorrect with Resolution List and Bitrate List information.
Quality mode switch does not support (CBR/Fixed the bug that quality) h. Arecont
AV12186
DI cannot work. i. EverFocus
For EMN2320, no support MPEG4.
For EMN2320, cannot switch CBR/VBR and only support VBR.
For EMN2320, no support 720x480, 704x480 and 640x480 resolution.
For ETN2110, motion detection is not compatible with MPEG4 codec because of camera firmware issue. j. Zavio
For F3210, Video resolution cannot change when only setup resolution.
For F3210, the AMR mode of talk function cannot work.
Bug Fixed the bug thated:
Mainconsole:
4. Sometimes click liveview will cause Maincosole crash when using Onvif model.
5. It will fail when Arecont AV-8365DN change format from MJPEG to H264.
NVRmini 2:
1. Samsung 3082:
(1) The resolution is not listed correctly under camera parameters.
(2) The selected frame rate is not being achieved.
(3) Latency in live view
73 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.13.0 (2013/05/27)
Modules:
Device Pack v 2.13.0
Supported Systems:
Mainconsole v 4.1.0 and above
NVRmini 2 v 1.5.0 and above
NVRsolo
Titan NVR v 1.3.0 and above
New Camera Supported:
ACTi D22, D62, E13, E22, E23, E24, E26, E33, E34, E43, E44, E45, E46, E54, E63,
E64, E65, E67, E73, E74, E83, E84, E85, E86 and E87
Arecont
Centrix
CNB
DigitalWatchdog
AV3146 and AV3256
Generic
ISMC1063P
MD421TIR
Dlink
Dynacolor
Everfocus
Fine
Guardeon
Network Camera
DCS-942L
Generic
EDN 1220, EDN 1320, EMN 2220, EPN 4220
ACM-B3000 and ACM-R3006, CDV-5VM501 and TCP-VM559
GDN-D3200IR, GDN-D3200V, GDN-F1300V, GDN-H1300IR and GDN- H3200IR
C3000 and C3000-W
74 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
JVC
Techson
UDP
Vivotek
Zavio
FW upgrade:
Eneo
VN-T16, VN-T216, VN-H657U and VN-H657WPU
TC-IP213WS
IPN100HD, IPN1202HD, IPN2102HD, IPN302HD, IPN3102HD, IPN3202HD,
IPN3502HD, IPN3502HD, IPN3502HDIR, IPN6602HD, IPN6802HD,
IPX3302HD, IPX3702HD, IPX4202HD and IPX4602HD
IP8152
D7320
GXC-1710M (upgrade to FW 2.11)
Notice:
6. Known issue: k. ACTi For D and E series camera:
NUUO recommend customers use CLOSE network environment as ACTi may shut down and restart automatically in some complex network environment.
ACTi will continue to figure out the reason and help to solve this issue.
The audio stream of E13 unstable sometimes, even though in VLC and web. l. Centrix Generic model:
The bitrate of dual stream cannot come to 500kbps when main stream setting is MJPEG and CIF.
Parameter setting will fail when enable multi-stream and resolution higher than 1080p.
Camera firmware must be cx20130506NSA or above then can use generic model. m. DynaColor Generic model:
Parameter setting will fail when enable multi-stream and resolution higher than 1080p.
Camera firmware must be z120130417NSA or above then can use generic model. n. Fine CDV-5VM501 not support UPnP search by camera firmware issue. o. NetworkCamera C3000 and C3000-W not support UPnP search by camera firmware issue. p. TC-IP213WS:
75 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Can not trigger motion alarm under H.264 1fps.
Can not search camera by UPnP when change http port except 80.
H.264 fps may not enough under TCP connection in high quality and frame rate settings. q. Digital Watchdog MD421TIR
Not support Zoom, Focus, Talk and VideoParamSetting(MainConsole only)
Not support dual stream when select single stream for ONVIF setting at webpage.
Setting frame rate to 0 did not work.
MJPEG with resolution 320x240 is invalid.
Quality value is not synchronized with webpage.
There are two port settings on camera web, web port and service port. When NUUO product and camera are located in the same network, you can use this web port as configuring port on NUUO product. If NUUO product and camera are located in different network, you must choose service port. Or "go to web" function on NUUO product setting page might direct to the wrong URL. r. CNB ISMC1063P
Not support audio codec G.726 when using TCP connection. s. Arecont AV3146DN-3310-D and AV3256PM
The streaming has low FPS under high quality. t. JVC VN-H657U
Firmware Issue: MJPEG video stream is unstable over high resolutions such as 1920X1080,
1280x720. u. JVC VN-T16U
Firmware Issue: MJPEG video stream is unstable over high resolutions such as 1920X1080,
1280x720.
Firmware Issue: The Encoder parameters may not sync camera web. v. JVC VN-H57
Firmware Issue: MJPEG video stream is unstable over high resolutions. w. JVC VN-H137
Firmware Issue: H264 video stream is unstable over low frame rate.
76 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 x. Zavio D7320
Talk function cannot work due to firmware issue.
When change the HTTP port from 80 into 8080, camera send IP address which including parentheses, such as [192.168.1.66].
When setting highest video setting with H.264, the fps could not reach up to 20. y. UDP
When used UPnP search, if changes the HTTP port from default 80 into 8080 and reboot the camera, it does not carry any port information with reply message.
IPN3502HD i. When setting highest video setting in main stream, the second stream will unstable and cannot work both in H.264 and MJPEG.
IPX4202HD i. cgi load failure: #402 ii. iii. iv.
Audio with choppy in higher video setting
Motion detection cannot disable once it trigger
Unstable stream with highest video setting, sometimes does not work. z. EverFocus EDN1220, EDN1320, EMN2220 and EPN4220
Not support MPEG4.
Can not switch CBR/VBR and only support VBR.
EDN1320 no support 720x480, 704x480 and 640x480 resolution. aa. Vivotek IP8152
CGI returns a wrong PTZ capability.
Bug Fixed the bug thated:
Mainconsole:
6. Hikvision 8254: support third stream, preset function can not synchronize with
Mainconsole.
7. Hikvision DS-6716HWI: Can not connect the camera except channel 1(Generic).
8. Grandstream GXV3501: Remove “Clean All” Button from Add Preset Point.
NVRmini 2:
2. Hikvision 8254: Preset function can not synchronize with NVRmini2.
3. Hikvision DS-6716HWI: Can not connect the camera except channel 1(Generic).
77 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Titan NVR:
1. Hikvision 8254: Preset function can’t synchronize with Titan NVR.
2. Hikvision DS-6716HWI: Can not connect the camera except channel 1(Generic).
NVRSolo:
1. Yodor YUC-H626: Can not auto detect this model.
Release Version v2.12.0 (2013/04/29)
Modules:
Device Pack v 2.12.0
Supported Systems:
Mainconsole v 4.1.0 and above
NVRmini 2 v 1.5.0 and above
NVRsolo
Titan NVR v 1.3.0 and above
New Camera Supported:
ACTi D11, D12, D21, D31, D32, D41, D42, D51, D52, D54, D55, D64, D65,
D71, D72, D81, D82, E11, E12, E21, E31, E32, E41, E42, E51, E52, E53,
Axis
CNB
E55, E56, E61, E62, E71, E72, E81, E82, E91 and E92
M3007 (fisheye camera)
IBP5030CR, IDC4050F, IDC4050IR, IDC4050VF, IDC4050VR, IDP4030VR,
IDP5035VR, IGC2050F, IGP1030, IGP2035F, ISS4032Z28W, IVC5055VR,
Dahua
Dlink
Etrovision
Fine
Hikvision i-Mege
IVP4030VR, IVP5035VR, IXC2050IR, IXP3035VR, NGE2055F
NXE3055MR, NDE5055MF, NVE5055VR, NVE5055MF and NDE5055VR
IPC-HDBW3101, IPC-HDB3101 and IPC-HFW3101C
DCS-2332L, DCS-3715, DCS-3716, DCS-6010L (fisheye camera), DCS-6616,
DCS-6817B1 , DCS-6915 and DCS-7513
, NXE3055VR,
EV8180A, EV8580A, EV8581A, EV8780A, EV8781A and EV8782A
ACM-V3002
DS-2CD2012-I, DS-2CD2112-(I), DS-2CD2212-I5 and DS-2CD2312-I
B3210E, G2212E, G2213E, G2214H, G3211E, N3211E and V2211E
78 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Network Camera
On Electronics
Planet
Saerim
Sunell
Vivotek
Zavio
FW upgrade:
Bosch
Levelone
Santec
3MP_BOX, 3MP_FD, 3MP_IR and 3MP_VD
CFB-10MP (IP+ only), CFB-13MP, CFB-20MP, CFB-30MP, CFV-20MP/LIR35
(IP+ only) ,CFV-13MP/LIR35, MDV-10MP (IP+ only), MDV-20MP,
MDV-20MP-AV (IP+ only), MDV-30MP, MDV-30MP-AV (IP+ only),
MDV-13MP/LIR20 (NAS only)
ICA-H652-PA-220
SR-IDC4050IR, SR-IDC4050VR, SR-IDC4050F, SR-IGC2050F, SR-IVC5055VR,
SR-IDC4050VF, SR-IXC2050IR, SR-IGP2035F, SR-IDP4030VR,
SR-IXP3035VR, SR-ISS4032Z28W, SR-IVP4030VR, SR-NGE2055F,
SR-NXE3055VR, SR-NXE3055MR, SR-NDE5055VR, SR-NDE5055MF,
SR-NVE5055VR, SR-NVE5055MF
SN-IPV54/31UDN, SN-IPC54/31EDN, SN-IPR54/31AKDN, SN-IPR54/31APDN
SN-IPD54/31VDN, SN-IPD54/31VDR, SN-IPV54/31ZDR, SN-IPV54/31UDR,
SN-IPC54/14EDN, SN-IPR54/14AKDN, SN-IPR54/14APDN, SN-IPD54/14VDN,
SN-IPD54/14VDR, SN-IPV54/14ZDR and SN-IPV54/14UDR
PD8136
D5210 and D7210
Samsung
NTC-265-PI and NDN-265-PIO (upgrade to FW 5.70.0311)
WCS-6020 (upgrade to FW 1.1.4.1) and WCS-6050 (upgrade to FW
1.0.4.2)
SNC-3302, SNC-3305, SNC-5312IR, SNC-5315IR, SNC-6202,
SNC-6212IR, SNC-6302, SNC-6312IRH and SNC-6315IRH (upgrade to FW 1.0.2.332)
SND-5010, SNB-5001, SND-5011, SND-5061, SNB-7001, SNB-7002,
SND-7011, SND-7061, SND-7082 and SNV-7082 add bitrate option on
H.264 3072/5120/6144/7168/9216/11264/12288/13312/14336
Notice:
7. Known issue: bb. ACTi For D and E series camera:
NUUO recommend customers use CLOSE network environment as ACTi may shut down and restart automatically in some complex network environment.
79 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi will continue to figure out the reason and help to solve this issue.. cc. iMege G2212E : If http port does not 80, UPnP search will fail. dd. LevelOne WCS-6020, WCS-6050
When select high resolution, camera’s frame rate will less than 30fps.
PTZ Home will stop when disable the home button at titan.
Image broken at high resolution.
Not support AAC codec. ee. D-Link
DCS-3715 i. Sometimes video setting can’t get the correct parameters2. Camera web setting is ii. very unstable and got slowly respond, especially in higher video parameter
When 1920x1080, 25 fps, and 8M bitrate, will get incorrect parameter or long respond iii. time cgi respond slowly.
DCS-6817B1 i. PTZ Autopan does not work ii. When enable mic only, the camera does not send any audio package.
DCS-6915 i. Not support talk
DCS-2332L i. In H.264 format, setting 1 fps and under 512kbps with max resolution cause unstable ff. Dahua connection.
IPC-HDBW3101, IPC-HDB3101 and IPC-HFW3101C i. FW issue, bit rate range is different between camera web and response to cgi. gg. Hikvision
DS-2CD2012-I i. DS-2CD2012-I FW issue: not support PTZ function but web setting can enable this hh. Planet option.
ICA-H652-PA-220 i. Camera response slow. ii. iii.
IO triggle time will delay about 3 secs.
Audio has some noise in web site. ii. Santec
SNC-6302, SNC-3305, SNC-63115IRH i. M-JPEG on high resolution and quality may not get parameter.
80 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 ii. Audio has some noise in high resolution. jj. Sunell SN-IPV54/31UDN:
FW issue: Camera will reboot when MJPEG 2048x1536, 1920x1080 and quality 9. kk. Bosch NDN-265-PIO:
It can't set resolution below 1280x720 when stream2 property set to "Copy Stream 1".
When H.264 quality is set to “0”, the camera will Auto-adjust the quality setting. For minimum quality, the value should be “100”.
Audio AAC can't work due to NUUO platform issues. ll. Etrovision EV8180A, EV8580A, EV8581A, EV8780A, EV8781A and EV8782A
Not support Talk.
With four profiles mode only support resolution 640x480. (camera limitation)
Not support MPEG4 in NVRmini 2/NVRsolo/TitanNVR.
Motion Detection only works on H.264.
It needs to reboot after changing HTTP port. mm. Fine ACM-B3000, ACM-V3001, ACM-V3002, ACM-R3002
MJPEG only support when MPEG4/H264’s resolution is lower than 1280x720 in
Mainconsole. nn. CNB
IGC2050F, IDC4050F, IDC4050IR, IDC4050VF, IDC4050VR, IVC5055VR and IXC2050IR i. FW issue: cannot set bitrate 128kbps when the resolution is D1 or VGA. ii. When selects MJPEG, 1fps, the actually received fps is 6.
IGP1030, IBP5030CR, IVP4030VR and IDP4030VR i. In the MJPEG format, the fps is not enough when resolution is XGA or SXGA.
IGP2035F, IDP5035VR, ISS4032Z28W, IVP5035VR, IXP3035VR i. Cannot set bitrate 128kbps when the resolution is D1 or VGA. It is firmware issue.
NGE2055F, NDE5055MF, NDE5055VR, NVE5055MF, NVE5055VR NXE3055MR, and
NXE3055VR i. ii.
Not support UDP connection.
Video connection cannot establish when the setting of bitrate is 9M or 10M. oo. Saerim
SR-IGC2050F, SR-IDC4050F, SR-IDC4050IR, SR-IDC4050VF, SR-IDC4050VR,
SR-IVC5055VR and SR-IXC2050IR i. ii.
Cannot set bitrate 128kbps when the resolution is D1 or VGA. It is firmware issue.
When it selects MJPEG, 1fps, the actually received fps is 6.
SR-IGP2035F, SR-IDP4030VR, SR-ISS4032Z28W, SR-IVP4030VR, and SR-IXP3035VR i. Cannot set bitrate 128kbps when the resolution is D1 or VGA. It is firmware issue.
81 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
SR-NGE2055F, SR-NDE5055MF, SR-NDE5055VR, SR-NVE5055MF, SR-NVE5055VR,
SR-NXE3055MR, and SR-NXE3055VR i. ii.
Not support UDP connection.
Video connection cannot establish when the setting of bitrate is 9M or 10M. pp. Zavio D5210 and D7210
The audio function of AMR7.95 cannot work.
The talk function with AMR codec cannot work.
The max frame rate of MPEG4 is up to 20 FPS in 1280x800. It is the limitation of hardware.
Bug Fixed the bug thated:
Mainconsole:
9. Forenix_ACDV-3VM501: can’t not choose h264 video format, cause by auto detect incorrect vendor and model name in DP 2.7 and behind, solve by add model name in corresponding function.
10. Samsung SPE-100: Incorrect maximum fps support.
NVRmini 2:
4. VisionHitech Mi series can’t connect.
Titan NVR:
3. Hikvision_DS-6101HFI-IP: LiveView do not have image.
4. Hikvision_DS-2CD752MF-FB: LiveView do not have image when change stream profile from original to low or min.
5. VisionHitech Mi series can’t connect.
82 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.11.0 (2013/03/26)
Modules:
Device Pack v 2.11.0
Supported Systems:
Mainconsole v 4.1.0 and above
NVRmini 2 v 1.5.0 and above
NVRsolo
Titan NVR v 1.3.0 and above
New Camera Supported:
ACTi
ADT
KCM8111
ADT-VSDVS-4C, ADT-VSDVZ5MP-VF3090IRI and ADT-VSDVZ5MP-VF3090IRO
American Dynamics
Bosch
CNB
ADCi600-D131
NDC-225, NWC-455, NWC-495, NWD-455, NWD-495 and VIP-X1XF-E
IDC4050VR, IDP5035VR, IVC5055VR, IVP5035VR, IXC2050IR, IXP3035VR,
NDE5055VR, NVE5055VR and NXE3055VR
Dlink
Dlink CN
Etrovision
Fine
Hikvision
LevelOne
Saerim
Sunell
DCS-2136L, DCS-3010, DCS-5010L
DCS-N70M-21H3, DCS-V70M-21H2, DCS-V70M-11H, DCS-N40M-22H3,
DCS-V40M-12H, DCS-V40M-32H2, DCS-N31M-21H3, DCS-V30M-51H2,
DCS-N62-40H2, DCS-N40M-81H3
EV8180Q-XD and EV8782Q-BD
ACM-R2001, CDB-MV720F, CDV-P360 (Fisheye camera, support on
Mainconsole only), TCP-HFB720
Generic model support second stream
FCS-1132, FCS-3052, FCS-5052 and FCS-5062
SR-IDC4050F, SR-IDC4050VR, SR-IDP4030VR, SR-IGC2050F, SR-IGP2035F,
SR-NDE5055VR, SR-NGE2055F, SR-NVE5055VR ,SR-IXP3035VR and
SR-NXE3055VR
SN-IPC54/40EDN, SN-IPD54/40VDN, SN-IPR54/40AKDN, SN-IPR54/40APDN,
83 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Techson
Zavio
FW upgrade:
Sony
SN-IPV54/40UDN and SN-IPV54/40UDR
TCIP-Typ213MDN22x
F3102, F3107, F3115
SNC-CH210 (FW v1.78) , SNC-CH260 (FW v1.78), SNC-DH120 (FW v1.78) and SNC-ER550 (FW v1.78)
Notice:
8. Known issue: qq. American Dynamics ADCi600-D131
Not support UPnP search.
Not support motion detection at MJPEG mode. rr. Fine CDB-MV720F
Frame rate cannot reach 30fps. ss. Fine ACM-R2001
Frame rate may not enough about 2~8 fps because of camera design. tt. Sunell SN-IPC54/40EDN
MJPEG 2592x1920 will image broken due to camera FW issue.
Camera will reboot when MJPEG 2048x1536 and quality 9 due to camera FW issue. uu. Sunell VSR54/01
MJPEG 2592x1920 will image broken due to camera FW issue.
DI can't work correctly due to camera FW issue. vv. Etrovision EV8180Q-XD, EV8782Q-BD
Not support Talk.
Under four profile mode only support resolution 640x480. (camera limitation)
Not support MPEG4 in NVRmini 2/NVRsolo/TitanNVR.
Motion Detection only works on H.264.
It needs to reboot after changing HTTP port. ww. LevelOne FCS-1132, FCS-3052, FCS-5052, FCS-5062
The Motion Detection of MPEG4 is error.
In Night mode, the Saturation cannot set. It is FW issue. (FCS-5062) xx. Sony SNC-CH210, SNC-CH260, SNC-DH120, SNC-ER550
84 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Dual stream cannot enable when H.264, 30fps, 1280x720(SNC-CH210, SNC-DH120,
SNC-ER550) or H.264, 30fps, 1920x1080(SNC-CH260) is selected for Image1.
The number of connection is 1 for JPEG and 2 for H264 and MPEG4 at the same time.
The PTZ function only support zoom in/out, focus near/far and auto focus function.
(SNC-CH260, SNC-DH120)
The connection cannot established with high probability when selected JPEG, high resolution and high quality.
(SNC-DH120, SNC-ER550) yy. Zavio F3102, F3107, F3115
Under AMR 7.95 mode cannot use talk and audio function.
The max frame rate of MPEG4 is up to 20 FPS in 1280x800. It's camera limitation. zz. D-Link
DCS-2136L: i. Constant bit rate cannot set bigger than 4M ii. In camera web video setting and NUUO camera setting page, when mode is MJPEG, set the Fixed the bug thated quality to "Excellent" and save, then change the Mode to
H.264, the “Fixed the bug thated quality” should also be "Excellent", but the "Good" option is show up due to camera FW issue. iii. ii.
When select resolution "176x144", it will display incorrect image
DCS-3010: i. Firmware Issue: Not support Talk
Firmware Issue: Bitrate setting
(more than 2Mkbps will cause broken-image and image delay) aaa. ii.
D-Link China:
DCS-N62-40H2 i. Firmware Issue: Not support Motion Detection
Firmware Issue: Bitrate List on web shows 3Mkbps
(the truly Bitrate value of camera could be 3Mkbps or 2.5Mkbps) iii. Speed setting only support pan speed(synchronized with Tilt speed)
DCS-N40M-81H3 i. Not support TCP/UDP bbb. Hikvision Generic model:
The camera setting will be failed, when sub stream resolution bigger than main stream resolution in Rapter platform. ccc. ADT-VSDVS-4C
Talk can't be use after setup audio codec.
Tilt up and down can’t be use.
Name of preset point only support a-z A-Z @-_!
85 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 ddd. ADT-VSDVZ5MP-VF3090IRI and ADT-VSDVZ5MP-VF3090IRO
Audio codec is wrong under AMR.
Camera may not connect under highest resolution, highest bit rate and lower frame rate.
Tilt up and down cannot use. eee. TCIP-Typ213MDN22x
Not support auto detection.
Not support DI/DO and audio.
Not support setup PTZ speed.
Video stream will have low frame rate with high quality under MJPEG.
Not support UPnP search.(Mainconsole)
The frame rate does not synchronize with web under MJPEG. fff. Bosch NWD-495, NWC-495, NWD-455, NWC-455
Auto detect model unsupported
H.264 supports up to a maximum of 2CIF as this utilizes the Baseline Profile.
When H.264 quality is set to '0', the camera will auto-adjust the quality setting. For minimum quality, the value should be '100'.
When MJPEG quality is set to '0', the camera will auto-adjust the quality setting. For minimum quality, the value should be '1'.
MJPEG frame rate depends on camera load. Value in settings dialog is not representative of actual frame rate ggg. Bosch NDC-225
When H.264 quality is set to '0', the camera will auto-adjust the quality setting. For minimum quality, the value should be '1'.
MJPEG quality depends on camera load. Value in settings dialog is not representative of actual quality.
Audio Codec support g711, not support L1, AAC. hhh. Bosch VIP X1 XF E
When H.264 quality is set to '0', the camera will auto-adjust the quality setting. For minimum quality, the value should be '1'.
MJPEG quality depends on camera load. Value in settings dialog is not representative of actual quality.
Audio Codec support g711, not support L1, AAC.
The resolution of profile-2(Mjpeg) will be limited to CIF, if the resolutions of profile-0(h264) and profile-1(h264) set by CIF.
H.264 video stream supports maximum resolution of 704x576 (PAL) and 704 x 480 (NTSC) only. Full D1 (720 x 576) is not supported. iii. Histream HH9801B-MPC-TD(HIHD_T_IR)
86 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
(MainConsole)Firmware Issue: Not support Motion Detection, DI, DO, video setting(Brightness/Contrast/Saturation)
(Mini2/Titan/Solo) Only support main stream video, camera setting(1920x1080,
1280x960, 1280x720). The other resolution not mentioned above are not supported.
Bug Fixed the bug thated:
Mainconsole:
1. Zavio V111T: The zoom in/out cannot stop.
2. Sunell: DI can’t work. (except VSR54/01 fw issue can not Fixed the bug that)
3. Bolide: DI can’t work.
4. Brickcom VS-01Ap: Cannot PTZ via joystick.
5. JVC VN-H*: Connect by http will cause CPU loading high, disable it.
NVRmini 2:
1. Grundig_GCI-K0523T, Grundig_GCI-H0503B: After selected H.264 video format in
NVRmini2, the video format will back to MJPEG.
2. Vivotek VS8801: There is no image for dual stream.
3. Sunell: DI can’t work. (except VSR54/01 fw issue can not Fixed the bug that)
4. Bolide: DI can’t work.
5. CNB IXC2050IR and IDC4050VR: disconnect after several hours.
6. JVC VN-H*: Connect by HTTP will cause CPU loading high (camera FW issue). NUUO suggest not connect via HTTP.
Titan NVR:
6. Vivotek VS8801: There is no image for dual stream.
7. Sunell: DI can’t work. (except VSR54/01 FW issue cannot Fixed the bug that)
8. Bolide: DI can’t work.
9. CNB IXC2050IR and IDC4050VR: disconnect after several hours.
10. JVC VN-H*: Connect by HTTP will cause CPU loading high (camera FW issue). NUUO suggest not connect via HTTP.
87 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.10.0 (2013/02/26)
Modules:
Device Pack v 2.10.0
Supported Systems:
Mainconsole v 3.5.0 and above
NVRmini 2 v 1.5.0 and above
NVRsolo
Titan NVR v 1.3.0 and above
New Camera Supported:
ADT
Beward
ADT-VSDVZ3MP-VF3010IRO
N100, N120, N300, N320, N600 and N630
CNB
Dynacolor
Dlink
Eneo
IDP5035VR, IGC2050F, IGP2035F, IVP5035VR, IXP3035VR and NGE2055F
NA083(IP+ only)
DCS-2210, DCS-5020L
PXD-1010F02 and PXD-1020F02
Honeywell
Vivotek
Zavio
FW upgrade:
Levelone
Panasonic
HDZ20HD, HDZ20HDE, HDZ20HDEX and HDZ20HDX
CC8130, FD8151V and IP8372
B5010, B5111, B5210, D3100, D3200, D5112, F7210 and F3110
Sunell
D-Link
Onvif support:
FCS-4041, WCS-6020 and WCS-6050
WV-SC385 and WV-SP105
SN-IPD54/12VDN
DCS-7413, DCS-6511
88 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
1. For ONVIF partner, NUUO only guarantee camera video connection (1st stream) with ONVIF test report.
2. Onvif Product line support: Titan(Profile S v12.06), Mini2(Profile S v12.06), Mini (Onvif v1.01)
Solo (Profile S v12.06) and Mainconsole(Profile S v12.06)
Notice:
9. Known issue: jjj. Sunell SN-IPD54/12VDN Can't test DI due to HW broken. kkk. CNB IGP2035F/IXP3035VR/IDP5035VR/IVP5035VR, Failed to set bitrate to
128k over VGA/D1. lll. ADT ADT-VSDVZ3MP-VF3010IRO
1. Audio codec is wrong under AMR.
2. Camera may not connect under highest resolution, highest bitrate and lower framerate. mmm. D-Link
1. DCS-6511: camera framerate is lower than user setting.
2. DCS-7413: When framerate is 1, camera connection isn't stable.
Not support MPEG4, TCP, UDP
3. DCS-5020L: (Titan/Mini2) Not support Audio
4. DCS-2210: Camera web and MainConsole can’t be set simultaneously. nnn. than 60
DynaColor NA083 Parameter setting will fail when Mjpeg quality bigger ooo. Eneo PXD-1010F02,PXD-1020F02 Parameter setting will fail when Mjpeg quality bigger than 60 ppp. Honeywell HDZ20HD,HDZ20HDE,HDZ20HDEX,HDZ20HDX Parameter setting will fail when Mjpeg quality bigger than 60 aa. OEM N73200, the AMR mode of audio doesn’t work correctly and the frame rate of MPEG4 is up to 20 due to the limitation of hardware. bb. Zavio
1. For F7210, due to audio and PTZ malfunction, the two functions can’t be verified unless new camera sample is provided. Thus, audio and PTZ function for F7210 is not guaranteed.
2. For D3100, there is no audio and the UPnP doesn’t include port settings. The two are known as FW issue.
3. For D3200 and F3110, the AMR mode of audio doesn’t work correctly and the frame rate of MPEG4 is up to 20 due to the limitation of hardware.
4. For B5210, the frame rate is not enough when using TCP and HTTP connection.
89 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 cc. Beward
1. For N300/320, only camera link is received for camera intergration. Thus, NUUO only guarantee video function.
2. For N100/120, audio will be disappeared after switch settings for a few times. (FW issue) qqq. LeveOne
For FCS-4041, High video parameter causes slow CGI command response.
Bug Fixed the bug thated:
Mainconsole:
- Fixed the bug that Zavio F210A motion detection cannot be triggered.
NVRmini 2:
- None
Titan NVR:
- Fixed the bug that Titan can’t login after connecting Samsung SNB-1001 several hours.
90 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.9.5 (2013/02/01)
Modules:
Device Pack v 2.9.5
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 and above v 1.5.0 and above v 1.3.0 and above
New Camera Supported: none
Bug Fixed the bug thated:
Mainconsole:
- Mainconsole would probably occur unexpected crash when first launch.
Copyright © 2014 NUUO Inc. All rights reserved.
91 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.9.0 (2013/01/21)
Modules:
Device Pack v 2.9.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 and above v 1.5.0 and above v 1.3.0 and above
New Camera Supported:
3Svision
Arecont
S4071
AV1145-04-W, AV1145-3310-D, AV1145-3310-W, AV1255, AV2145-04-D,
AXIS
Beward
Bullwark
Dlink
Everfocus
Fine
Forenix
Hikvision
Levelone
AV2145-04-W, AV2145-3310-D, AV2145-3310-W, AV3255 and AV10255
M1013, M1144, M3006, P1204, P1354 and Q7424
N100, N120, N300, N320, N600 and N630 (Mainconsole support only)
BLW-510MP-BS
DCS-5605, DCS-5635, DSC-932L, DCS-6210, DCS-7110, DCS-2230, DCS-6513 and DSC-6915
EDN2210 and EPN4220
3MP_BOX, 3MP_FD, 3MP_IR,3MP_PT, 3MP_VD and CDB-HD280
C2200, C2200-W, FBX-200, FBX-300WD, FDM-200, FDM-300WD, FVD-200,
FVD-300WD, M0202-BH01, M0202-BH02, M0202-BH03, M7202-DB03,
M4202-DB03 and M4202-DB02
DS-2DF1-572
WCS-6020 and WCS-6050
92 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
MegaIP
Messoa
NTIC
OEM
Probe
Samsung
Santec
Sunell
NCD-2003PR and NMX-2003P
NCB855, NCC800 and NIC950
HVS-D1-V3
N73110
PID-H1300
SND-5010
SNC-3305, SNC-5315IR, SNC-6202 and SNC-6315
IPS54/71DN/Z18 and IPS54/80DR
TP-LINK
VisionHitech
Vivotek
Yudor
Zavio
FW upgrade:
Arecont
Messoa
Probe
TL-SC3130v2 and TL-SC3130Gv2
Vision SM3Ti
IP8172
YUC-H626, YUC-H7926 and YUC-Hi26
B5010, B5210, D3100, and F7210
AV8185 and AV8365
NIC950
PIC-H2010, PIN-H1310 and PMI-H2000
Onvif support:
3. For ONVIF partner, NUUO only guarantee camera video connection (1st stream) with ONVIF test report.
4. Onvif Product line support: Titan(Profile S v12.06), Mini2(Profile S v12.06), Mini (Onvif v1.01) and Mainconsole(Profile S v12.06)
Notice:
10. Known issue: rrr. Yudor YUC-H626, YUC-Hi26, YUC-H7926:
In website, when bitrate mode is “CBR” and change stream mode from “Advanced mode” to
“Basic mode”. Quality will not synchronized to web. sss. Santec SNC-6315:
M-JPEG on high resolution and quality may not get parameter. ttt. VisionHitech Vision SM3Ti,
1. Sometimes can't get camera parameter normally due too camera response too slow, but there is chance to recover after reboot.
93 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
2. Audio may discontinuously under high resolution, framerate and bitrate settings. uuu. LevelOne WCS-6020, WCS-6050
WCS-6050 not support MJPEG 1280x1024
Not support preset
Camera’s framerate is less than 30fps at high resolution.
PTZ Home is stopped when the button is released at titan.
Broken textures at high quality.
Not support AAC codec. Users have to set AMR codec via camera web. vvv. Everfocus EDN2210 :
Sometimes can't get camera’s parameter at high resolution. www. Beward
1. For N300/320, only camera link is received for camera intergration. Thus, NUUO only guarantee video function.
2. For N100/120, audio will be disappeared after switch settings for a few times. (FW issue) xxx. 3SVision S4071
1. The quality setting of M-JPEG is unavailable.
2. When the server attaches two or more channels, the maximal framerate is unstable. yyy. Zavio
1. For F7210, due to audio and PTZ malfunction, the two functions can’t be verified unless new camera sample is provided. Thus, audio and PTZ function for F7210 is not guaranteed.
2. For D3100, there is no audio and the UPnP doesn’t include port settings. The two are known as FW issue. zzz. TP-LINK TL-SC3130v2 and TL-SC3130Gv2
Not support audio with AMR 7.95. aaaa. Messoa NCC800, NCB855
1. Set parameter will take 10 sec or more to setup.
2. Get parameter may wrong after set parameter.
3. Broken textures on connected in 1~4sec at MPEG4.
94 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
4. Not support auto detection.
5. For NCB855, setup bit rate of MPEG4 will response wrong parameter. bbbb. Messoa NIC950
1. Not support UPnP.
2. Not support auto detection.
3. Not support motion detection on MJPEG.
4. Not support DI and DO. cccc. Probe PID-H1300
Auto detection fail. (FW issue) dddd. D-Link
1. DCS-7110: not support Preset and HTTP protocol
2. DCS-6915: not support Preset, Audio 40kbits mode, Talk, Motion Detection and Flip.
3. DCS-2230: Quality setting fail in MJPEG
4. DCS-6210: Flip/Mirror acts contrary
5. DCS-6513: Preset issue(1st point position will be covered by 2 nd point position), Talk voice abnormal
6. DCS-5635: Not support autopan speed setting and MPEG4 format in HTTP
7. DCS-5605: Not support MPEG4 format in HTTP eeee. Bullwark
BLW-510MP-BS: Get parameter will fail when Mjpeg quality bigger than 60. ffff. Axis
P1354: Not support AAC in MJPEG. Not support AAC in H264 in Titan and Mini2 v1.6, but support in Mini2 v1.5.
Bug Fixed the bug thated:
Mainconsole:
- Hikvision Generic:
1. If device not support PTZ function, PTZ push-button will not be disable.
2. Autodetect function can’t find generic model.
3. MD delay
4. There are broken texture when use high resolution and low frame rate.
- Messoa:
1. The default values of video parameter are different from camera web on MainConsole.
95 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
NVRmini 2:
- Hikvision Generic:
1.If device not support PTZ function, PTZ push-button will not be disable.
2.Autodetect function can’t find generic model.
- CNB IDC4000T:
1.the device can not connect and can not set up on camera web page after a period of time.
Titan NVR:
- Hikvision Generic:
1.If device not support PTZ function, PTZ push-button will not be disable.
2.Autodetect function can’t find generic model.
- CNB IDC4000T:
1.the device can not connect and can not set up on camera web page after a period of time.
96 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.8.0 (2012/12/19)
Modules:
Device Pack v 2.8.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 and above v 1.5.0 and above v 1.3.0 and above
New Camera Supported:
ACTi
Arecont
KCM5511
AV8185DN, AV8365DN, AV20185DN and AV20365DN
AXIS
Bolide
Bosch
Corum
Dlink
Eneo
Everfocus
Hikvision
M3005
BN1009/PTZ3GIP, BN1009/PTZWDRIP, BN1009M/PTZ-18, BN2002IP,
BN2002WDRIP, BN2009AVAIRIP,BN2009IRIP, BN2009WDRVAIRIP, BN2035IRIP,
BN2035WDIRIP, BN5002M-A, BN5009M-A and BN5035M-A
NTC-265-PI and NDN-265-PIO
CS-150-IO, CS-195-IO, CS-310-IO, CS-320-IO, CS-390-IO, CS-410-IO and
CS-425-IO
DCS-2310L, DCS-3112, DCS-6314, DCS-6915(Mainconsole support), DCS-7413 and DCS-7513
GXB-1720M-IR, GXC-1605M, GXC-1606M-IR, GXC-1720M, GXD-1610M-IR, and
GXD-1720M-IR
EPN4220
DS-2CD8253F-EI, DS-2CD8264FWD-(EIS), DS-2CD864FWD-E, DS-2DF1-572
97 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ITX
LevelOne
LG
Rover
Samsung
Sony
Tiandy
Vivotek
Yudor
FW upgrade:
Panasonic
(Mainconsole support) and Generic
NCD-2003PR(Mainconsole support), NMX-2003P(Mainconsole support)
WCS-6020(Mainconsole support), WCS-6050 (Mainconsole support)
LDW2010, LSW900, LSW901, LSW2010, LVS201, LVS301, LVS311, LVW700,
LVW701, LVW900, LVW901, LW352, LW355, LW9226, LW9226I, LW9228,
LW9228I
RV19BMVP and RV19BMVIR
SNB-5001, SND-5011 and SND-5061
SNC-VB600 and SNC-VB630
TC-NS324S2-V2.1
IP8172(Mainconsole support)
YUC-H696, YUC-766R-30, YUC-H796R, YWS-H01DP and YWS-H04S
DG-SW155, WV-SP135E and WV-SW155
Notice:
Known issue:
I. ACTi KCM5511
Pitch of G.711 audio is not correct.
Not support motion detection in M-JPEG.
II. CORUM
Under particular operation, the quality or resolution of video parameter can't be set. It needs set quality on camera web again.
The particular operations sequence is as follows:
In Advanced Mode -> use VBR -> Apply -> use CBR -> Apply -> change to Basic Mode ->
Apply
CS-425-IO and CS-195-IO: Not support 2 nd stream in maximum frame rate of 1080p.
CS-230-IO: Cannot setup saturation. (IP+)
CS-390-IO: Not support UPnP.
CS-150-IO, CS-195-IO, CS-320-IO, CS-390-IO, CS-410-IO and CS-425-IO: When input under N.C status, needs trigger input more than 10 sec if you want to cancel event of input.
98 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
III. Sony SNC-VB600,SNC-VB630
Not support Motion Detection.
Not support Audio.
Alarm Input doesn’t work.
IV. VIVOTEK IP8172
Not support CBR mode (MainConsole).
MJPEG not support audio.
Not support AAC audio.
I. LevelOne WCS-6020, WCS-6050
Camera does not stable at bad network environment. For example, UPNP search failed, no video…etc.
Not support preset
WCS-6050 not support MJPEG 1280x1024
II. Hikvision
DS-2CD8264FWD-(EIS): Not support PTZ
DS-2CD864FWD-E: Not support DI, G726 talk, zoom in/out
DS-2CD8253F-EI: Not support audio but the clickbox is opened(cgi issue).
III. D-Link
DCS-6915: Not support talk, Motion Detection, DI, DO
DCS-3112: Not support Preset
IV. Bolide
All Bolide models changing MJPEG resolution may get Fail message due to camera FW issue.
(MainConsole/Mini2/Titan)
All Bolide models AutoDetect model may fail due to incorrect model name response.
(IP+/Mini2/Titan)
BN2002WDRIP, BN5002M-A: AlarmIn message is unstable.
V. Bosch NTC-265-PI:
MJPEG Quality always get 70 (Camera Firmware Issue). (MainConsole)
H264, MJPEG set Quality 0 but get 24 (Camera Firmware Issue). (MainConsole /Mini2/Titan)
MJPEG lag (Camera Firmware Issue). (MainConsole)
99 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Audio Codec supports g711, not support L1, AAC. (MainConsole /Mini2/Titan)
VI. Tiandy TC-NS324S2-V2.1
Audio at titan is bad.
Only support streaming
VII. ITX NCD-2003PR:
When set Anti-Flicker Mode to 50Hz, Mainconsole would get wrong Max of FPS(30).
(Firmware issue)
VIII. LG LW9226:
Audio out sound level is too small (with high impedance).
IX. LG LVS201:
Video image has some noise in the bottom line when video resolution at QCIF.
Bug Fixed the bug thated:
Mainconsole:
- Samsung SND-3082 video will disconnect after continuous control PTZ several minutes.
- Panasonic DG-SF334 force setting bitrate value when codec is H264.
NVRmini 2:
- AMTK AM2221D, AM2231D preset name can't contain blanks.
Titan NVR:
- AMTK AM2221D, AM2231D preset name can't contain blanks.
- Sony SNC-EP580 PTZ speed is too slow.
100 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.7.2 (2012/11/28)
Modules:
Device Pack v 2.7.2
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
New Camera Supported:
AXIS M3005 (For Mini2 and Titan only)
Copyright © 2014 NUUO Inc. All rights reserved.
101 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.7.0 (2012/11/19)
Modules:
Device Pack v 2.7.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
New Camera Supported:
Airlive
AMTK
OD-325HD
AM2030D, AM2110D, AM2120D, AM2221D, AM2231D, AM2530D, AM2570D,
Asoni
AXIS
Bosch
Camtron
Corum
Forenix
Hikvision
Histream
Lilin
AM2590D, AM2630D and AM2730D
CAM613M, CAM614, CAM615, CAM616M, CAM619M, CAM620, CAM624M,
CAM625M, CAM627M, CAM628M, CAM630, CAM632, CAM633, CAM634M,
CAM637M, CAM638, CAM639(Mini2/Titan only), CAM640, CAM641(Mini2/Titan only), CAM642M, CAM647, CAM656D, SVR610, SVR611, SVR640
P5544
NDC-274-P and NDC-274-PT
HLC-81AD/P, HLC-83V, HLC-83V/W,HLC-84V and HLC-84V/W
CS-270-IO
NPB-720, NPB-720A, NPB-720U, NPD-720K and NPD-720R
DS-6601HFHI (Mainconsole only)
HIHD_64
IPD2220ES, IPG1022ESX, IPG1022ES, IPR320ESX, IPR434ESX, IPR7424ESX
102 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Messoa
Samsung
Tiandy
JVC
(Mini2/Titan support)
NCR-875PRO,NDR-891, NIC-990
SNB-7001, SNB-7002, SND-7011, SND-7061, SND-7082 and SNV-7082
TC-NH9106S2-MP
VN-H37U, VN-H57U, VN-H137U, VN-H157WPU, VN-H237U, VN-H257U,
VN-H257VPU, VN-V685U, VN-V686BU, VN-V686WPBU (Min2/Titan support,
Mainconsole have supported on DP v2.5)
Notice:
11. Known issue: dd. Bosch NDC-274-P
- MJPEG Quality always get 70 (Camera Firmware Issue).
- MJPEG set Quality 0 but get 24 (Camera Firmware Issue).
- MJPEG lag (Camera Firmware Issue). ee. Airlive OD-325HD and AMTK AM2030D, AM2110D, AM2120D, AM2221D, AM2231D,
AM2530D, AM2570D, AM2590D, AM2630D and AM2730D Always can use http port 80 to connect after changing http port by FW issue. ff. Airlive OD-325HD and AMTK AM2590D, AM2030D, AM2570D, AM2530D, AM2630D,
AM2730D Initail output status will not synchronize to real output voltage by HW issue. gg. AMTK AM2221D, AM2231D preset name can't contain blanks. hh. Histream HIHD_64 camera response very slow, when change video parameter, there is high opportunity to disconnect. Just wait for a while, or reboot camera, and then be able to reconnect. ii. Hikvision DS-6601HFHI
- UPnP search can’t find the camera.
- Can't change port on camera web site.
- Talk sound is not fluent jj. Messoa NDR891 and NCR875PRO
- Set parameter will take 10 sec or more to setup(Camera Firmware Issue).
- Get parameter may wrong after set parameter(Camera Firmware Issue).
- Broken textures on connected in 1~4sec at MPEG4(Camera Firmware Issue).
- Not support auto detection.
- Setup bit rate of MPEG4 will response wrong parameter on Mini2/Titan(Camera Firmware
Issue).
- Not support talk on MainConsole.
- The default values of video parameter are different from camera web on MainConsole. kk. Messoa NIC990
103 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
- Can't set frame rate(Camera Firmware Issue).
- Only support H.264.
- Not support dual stream on 1080P(Camera Firmware Issue). ll. Camtron HLC-81AD/P doesn’t support autodetect & search mm. LILIN IPD2220ES, IPG1022ESX, IPG1022ES, IPR320ESX, IPR434ESX,
IPR7424ESX Video parameter does not synchronize to ONVIF option. nn. LILIN IPR434ESX does not support dualstream at 2048x1536 oo. Tiandy TC-NH9106S2-MP
1. Not support ONVIF event (MD, I/O).
2. Not support minor stream.
3. Not support dual stream.
Bug Fixed the bug thated:
Mainconsole:
- Fine SP-HP2020Q-IP patrol cause IP+ dump.
- Levelone FCS-3091 can’t use talk function.
NVRmini 2:
- CNB IDP4000VD open dualstream failed.
- Vivotek SD8XXX series preset issue.
- Panasonic WV-SW395, WV-SW396 preset issue.
Titan NVR:
- CNB IDP4000VD open dualstream failed.
- Vivotek SD8XXX series preset issue.
- Panasonic WV-SW395, WV-SW396 preset issue.
104 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Release Version v2.6.0 (2012/10/19)
Modules:
Device Pack v 2.6.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
New Camera Supported:
Axis M1014 , M1143-L, M3004, M7014, P7224 and Q7406
DCS-2130 (Titan/Mini2 support and Mainconsole already support on v2.5) and
D-Link
Everfocus
Forenix
Jetstor
DCS-3716
EDN3160, EDN3260, EDN3340, EHN3160, EHN3260, EHN3340 and EPN4122
ACD-3VM501 and NPB-720BM
JS-C1100, JS-C2100, JS-WGP-100-CB, JS-B0100, JS-B0100-W, JS-B0131,
JS-BB1100-R30, JS-B1100, JB-B1204-R25, JS-D0100, JS-D1100, JS-D1130,
JS-D1204, JS-ISD0200x18 and JS-OSD0200x20
Levelone
Samsung
Shany
FCS-3071-V2
SNP-6200, SNP-6200H, SNP-6200HP, SNP-6200P
SNC-21XX ( SNC-WD2112MDN, SNC-WD2122DN, SNC-WDL2132DN,
SNC-WDL2142DN)
SNC-22XX ( SNC-2212MDN, SNC-2222DN, SNC-L2232DN)
SNC-23XX (SNC-WD2312MDN, SNC-WD2322DN, SNC-WDL2132DN,
SNC-WDL2332DN)
105 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Sunell
Techson
Zavio
IPS54/70DN/Z18, IPS54/70DN/ZR18, IPS54/70DR/Z18, IPS54/70DR/ZR18,
SN-IPC54/11FDN, SN-IPC54/11DN, SN-IPC54/11EDN, SN-IPV54/11DN,
SN-IPV54/11DR, SN-IPD54/11VDN, SN-IPD54/11VDR, SN-IPV54/11UDN,
SN-IPV54/11UDR, SN-IPR54/11DN, SN-IPR54/11ANDN, SN-IPV54/11ZDR,
SN-IPR54/11ALDN, SN-IPR54/11AKDN, SN-IPD54/12VDN, SN-IPC54/12DN,
SN-IPC54/12EDN, SN-IPC54/12FDN, SN-IPV54/12DN, SN-IPV54/12DR,
SN-IPD54/12VDR, SN-IPV54/12UDN, SN-IPV54/12UDR, SN-IPR54/12DN,
SN-IPR54/12ANDN, SN-IPV54/12ZDR, SN-IPR54/12ALDN, SN-IPR54/12AKDN and VSR54/01
TCIP-220MDN, TCIP-230WDRMDN, TCIP-213WDRMDN, TCIP-D213WDRDN
TCIP-D220DN, TCIP-D230WDRDN, TCIP-LD213WDRMDN, TCIP-LD220MDN,
TCIP-LD230WDRMDN and TCIP-LPro213WDRMDN (Mini2 and Titan support,
Mainconsole already support on DP v2.5)
D5113, D7111, F1100 and F1105
Notice:
12. Known issue: pp. Sunell SN-IPD54/12VDN, VSR54/01 autodetect fail due to camera FW issue.
IPS54/70DN/ZR18 VSR54/01 changing MJPEG resolution may get Fail message due to camera FW issue. Can’t support G711 A-law(Onvif issue) qq. Axis P7224 can’t use second audio in (All). Support G.711 only (mini2/Titan). rr. Forenix NPB-720BM doesn’t support On-edge motion under TCP or UDP protocol. ss. Digital WatchDog DWC-MPA20M does not support On-edge motion detection. tt. Digital WatchDog DWC-MPA20M, if switching between profiles constantly(about 5~10 times), sometimes the camera is just disconnected and no longer connected again until rebooting it uu. 2.5 and 12.5 framerate can’t be show at EPN4122.
Bug Fixed the bug thated:
Mainconsole:
- Can’t connect over 3 Pelco IP110 devices.
- Icantek icanview240 can’t use PTZ.
- Probe connection failed after several minute.
- EverFocus ONVIF camera responses LAN address in NAT environment.
NVRmini 2:
- Panasonic WV-SW395 PTZ speed moving angle too much.
106 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
- Probe connection failed after several minute.
- Vivotek some PTZ models can’t control PTZ when PTZ speed is 0 in the camera web interface.
- EverFocus ONVIF camera responses LAN address in NAT environment.
Titan NVR:
- Panasonic WV-SW395 PTZ speed moving angle too much.
- Probe connection failed after several minute.
- Vivotek some PTZ models can’t control PTZ when PTZ speed is 0 in the camera web interface.
- EverFocus ONVIF camera responses LAN address in NAT environment.
Release Version v2.5.0 (2012/09/18)
Modules:
Device Pack v 2.5.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
New Camera Supported:
107 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi
Axis
Dahua
D-Link
Ernitec
Guardeon
Honeywell
JVC
LG
Vivotek
KCM5611 and KCM7911
Q1604 and Axis (for IP camera and video servers’ Video only)
SD65XX-HN and SD69XX-HN
DCS-2130 (Mainconsole only)
Mercury SX 302, Mercury SX 302IR, Mercury SX 302M, Orion SX 802IH, Orion SX
802OPH, SX 605, Vega SX 102 and Vega SX 102IH
GDN-V1300D, GDN-DV1300IR and GDN-D1300IR
HCD5MIH, HD3MDIH and HD4MDIH
VN-H257U, VN-H257VPU, VN-H37U, VN-V685U, VN-V686BU and
VN-V686WPBU(Mainconsole only)
LNB3100, LNB5100, LND3100, LND5100, LNP2800, LNP2800I, LNP3700, LNP3700T,
LNV5100, LNV5110, LW130W, LW332, LW335, LW342, LW345, LW6324, LW6354,
LW6424, LW6454 and LW9422
FE8171V (Mainconsole only and Titan/Mini2 already support on v1.13) and FE8172V
Notice:
13. Known issue: a. ACTi KCM5611 does not support RS-485 (not support Pan/Tilt). b. Dahua SD65XX-HN, SD69XX-HN does not support motion detection at MJPEG.
MJPEG bitrate can’t set over 8192 kbps. c. Axis Generic support video only. d. Axis Q1604 does not support AAC at MJPEG and not support H264 CBR mode. e. Guardeon does not support audio in with 16KHz sampling rate.
f. LG series can’t support dual-stream when video parameter is H264, 1920x1080(or above), over 20fps.
g. LG Speed Dome models (LW9422, LNP3700T) PTZ will stop automatically when press bottom
108 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 over 10 sec. Focus near/far needs to setup the focus mode in camera’s OSD. Adjust zoom speed is useless. i. Vivotek FE8172V, not support CBR mode. Not support audio at MJPEG. Not support AAC audio.When resolution is 1360x786, video stream would have a white line at the left-bottom of the frame. If set to Full HD mode, the low profile video stream would have a color line at the bottom of frame.
Bug Fixed the bug thated:
Mainconsole:
- Fixed the bug that Santec SNC-8322 PTZ “down-left “
- Fixed the bug that Dynacolor NV053, NV223 autofocus
- Probe PIC-H2010 with wrong MAX framerate support.
- Zavio B7210, F7210 with wrong resolution support.
NVRmini 2:
- Panasonic WV-SC385 can’t get preset point.
- Sunell SN-IPS54/60DN/Z18/WI Motion Detection failed after 60sec.
Titan NVR:
- Panasonic WV-SC385 can’t get preset point.
- Sunell SN-IPS54/60DN/Z18/WI Motion Detection failed after 60sec.
Release Version v2.4.0 (2012/08/20)
Modules:
Device Pack v 2.4.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
New Camera Supported:
109 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi
Alphatech
Brickcom
Grundig
Probe
Sunell
Techson
Videosec
Vivotek
3Svision
TCM1111, TCM3111, TCM4511, TCM5111 and TCM6630
AT-IMF5736 and AT-IMV5756
30xN
GCI-K1526V and GCI-K1812W
PIC-2010T and PIN-H1310
SN-IPS54/60DN/Z18/WI
TCIP-213WDRMDN, TCIP-220MDN, TCIP-230WDRMDN, TCIP-D213WDRDN,
TCIP-D220DN, TCIP-D230WDRDN, TCIP-LD213WDRMDN, TCIP-LD220MDN,
TCIP-LD230WDRMDN and TCIP-LPro213WDRMDN (Mainconsole only)
ICS-20W, ID-20, IRD-20 and IRW-20W
BB5116, BB5315, BD5115 and FD8131
N3071, N6072, N6073, N6074, N6075, N6076, N6077 and N9071
Notice:
14. Known issue: a. ACTi TCM6630, DI/DO useless, FW issue. b. AlphaTech models, 2nd profile's framerate will be limited to 15fps when 1st profile set resolution to 1600x1200. Framerate only support 3~25fps. c. Brickcom 30xN, Cover FB-300Np, WFB-300Np, MD-300Np. MD-300Np is no support DI/DO and one way audio only. d. Grundig models, camera become slow response (or not response) when set resolution, compression and framerate near the maximum value, audio will not smooth at the same time. Suggest modify GOV length to small value when video framerate lower than 5. e. Probe series, will access failed when add more than 1 channel to the same camera.
110 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
f. Sunnell SN-IPS54/60DN/Z18/WI, dual-stream will connect failed when camera is too busy.
15. Bug Fixed the bug thated:
Mainconsole:
- Brickcom VS-04A, can’t be selected in the camera support list.
NVRmini 2:
- ACTi CAM6610, adjust PTZ speed to adequate speed.
- Grundig C3075, increase the PTZ control latency.
- Sunnell camera can’t disconnect automatically when press disconnect button.
Titan NVR:
- ACTi CAM6610, adjust PTZ speed to adequate speed.
- Grundig C3075, increase the PTZ control latency.
- Sunnell camera can’t disconnect automatically when press disconnect button.
Release Version v2.3.0 (2012/07/18)
Modules:
Device Pack v 2.3.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
New Camera Supported:
111 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Alphatech
Basler
Dynacolor
Mobotix
Santec
Telview
Vivotek
AT-IMF5739 and AT-IMF5750
BIP2-D1920c-DN na063
M24M-Sec
SNC-3322 and SNC-8322I/HO
IPB612P-ICR, IPB630P-ICR, IPD612-VP-VF-IR, IPD630-VP-VF-IR, IPE600, IPW612,
IPW630, IPW630P, IPZ611, VIS611, VIS614 and VIT621
FD8335H, FD8372 and IP8361
Notice:
16. Known issue: a.Alphatech AT-IMF5739, AT-IMF5750
2nd profile's framerate will be limited to 15fps when 1st profile set resolution to 1600x1200.
Framerate only support 3~25fps.
b.Basler BIP2-D1920c-DN
Not support Audio & Talk
c.Dynacolor na063
Video parameter can't sync with camera web interface, need to refresh the browser.
Talk quality is not clear.
Camera efficiency will done when set high resolution & quality stream.
112 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
d.Mobotix M24-Sec
Audio only support on MxPEG.
Motion event works abnormal until first time trigger.
Resolution of dual-stream can't bigger then main-stream.
e.Vivotek FD8372
Mpeg4 support first 2 maximum resolutions are 1920x1920 & 1920x1536.
17. Bug Fixed the bug thated:
Mainconsole:
- Etrovision EV8180U black video when set resolution to 1920x1080.
NVRmini 2:
- CNB IDC4050IR, IDC4050F dualstream doesn’t work.
Titan NVR:
- CNB IDC4050IR, IDC4050F dualstream doesn’t work.
Release Version v2.2.1 (2012/07/05)
Modules:
Device Pack v 2.2.1
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
Notice:
Copyright © 2014 NUUO Inc. All rights reserved.
113 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
1. Bug Fixed the bug thated:
For Eneo GCD1710M-IR, please remove DP v2.2.0 first then install DP v2.2.1 and reset
Mainconsole: a. Eneo camera model correct to GXD-1710M-IR b. Axis P7210 can not view the correct video channels with Codec H264.
NVRmini 2: a. Eneo camera model correct to GXD-1710M-IR
Titan NVR: a. Eneo camera model correct to GXD-1710M-IR
Release Version v2.2.0 (2012/06/19)
Modules:
Device Pack v 2.2.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
New Camera Supported:
114 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi
Arecont
Axis
Brickcom
Eneo
Hikvision
Mobotix
Samsung
Vivotek
KCM-3311 and KCM-7311
AV2116 and AV3116
M7014, P3354, Q1604, Q7414 (NVRmini 2, Titan NVR only)
P3364
OB-100Ap, VS01A, PZ-040D and PZ040E
GXB-1710M-IR, GXC-1710M and GCD-1710M-IR
DS-2CD7153-E
D-14D Sec
SNB-1001, SND-1011, SND-1080, SNO-1080R, SNV-1080 and SNV-1080R
FD8372, FD8136, IP8133, PT8133, SD8362
Notice:
1. Known issue: a. Hikvision DS-2CD7513-E this camera can not set framerate 15~22 when resolution is 1600x1200,1600x912. sometimes camera can't set resolution 1600*1200、1600*912、1280*960.
2. Bug Fixed the bug thated:
Mainconsole: b. ACTi KCM-5211 PTZ function will be useless after 1 week. (Need upgrade FW V5.05.07 & ISP
V1.02.02) c. Samsung SND-3080 can not get the parameter of the video stream.
NVRmini 2:
115 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
None
Titan NVR: a. Axis Q7406 can not support PTZ control. b. Axis P7210 can not view the correct video channels with Codec H264. c. UDP IPE3500M disconnect automatically after 24hours. d. Vivotek SD83x2, SD83x3 can not adjust the PTZ speed. e. Zavio B7201 video broken in LiveView.
Release Version v2.1.0 (2012/05/21)
Modules:
Device Pack v 2.1.0
Supported Systems:
Mainconsole
NVRmini 2
Titan NVR v 3.5.0 above v 1.5.0 above v 1.3.0 above
New Camera Supported:
Copyright © 2014 NUUO Inc. All rights reserved.
116 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
Axis
Brickcom
CNB
COP
Guardliner
Hikvision
Panasonic
Samsung
Santec
Vision Hi-Tech
Vivotek
3SVision
P3367, P7210, P7214, P8513, P8514, Q1602, Q1602-E, Q1922 and Q1922
130N series and 50xA series
IDC4000T
15-WS01D-E
SPmicro-412
DS-2CD853F-E
WV-SC386, WV-SP508, WV-SP509, WV-ST162. WV-ST165, WV-SW172,
WV-SW174W, WV-SW175, WV-SW314, WV-SW316/L, WV-SW558 and WV-SW559
SNP-3302/H
SNC-3342 and SNC-6332
I series, Mi series, M3i series and NVS102
FD8134-SS, IP7160-SS, IP7161-SS, IP8151-SS, IP8161-SS, IP8162P-SS,
IP8332-SS, SD8121-SS, SD8362E, SD8362-SS, SD8323E-SS
N3072, N5071 and N8072
Notice:
3. Known issue: a. Brickcom 130N series need waiting 15s to finish adjust the zoom/focus. b. Brickcom 50xA series need waiting a period of time to reconnect stream success when switch the video resolution higher than 1920x1080. c. Hikvision DS-2CD853F-E can't set framerate 15~22 in Max resolution.
4. Bug Fixed the bug thated:
Mainconsole:
Fixed the bug thated Sony SNT-V704 can’t connect failed.
Fixed the bug thated UDP camera image gray out or break randomly when config different
117 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 resolutions.
NVRmini 2:
Fixed the bug thated Axis M7001 can’t use daulstream.
Titan NVR:
None
Release Version v2.0.0 (2012/04/18)
Modules:
Device Pack v 2.0.0
Supported Systems:
Mainconsole v 3.5.0 above
NVRmini 2 v 1.5.0 above
Titan NVR v 1.3.0 above
Copyright © 2014 NUUO Inc. All rights reserved.
118 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
ACTi
Arecont
KCM-3211, KCM-3911
AV20185CO, AV20365CO, D4F series
Axis
Bullwark
Centrix
M3113-R, M3113-VE, Q6032
BLW-230MP-BS, BLW-230MP-DS, BLW-IN220X-S, BLW-IR230MP-DSM,
BLW-IR230MP-SM and BLW-OUT220X-S
B13H, C10, C10-W, D13HD, W13H
Dynacolor
Forenix
GE
Hikvision
IQinvision
Levelone
Panasonic
Rover
Samsung
Vivotek
Zavio
NH720-20N1, NH820-20N1, nv103, nv223, nv053 and nv063
B0202
TVC-MP2B-S
DS-2CD754F-EI, DS-2CD8254F-EIS, DS-2CD752MF-E, DS-2CD754F-E
DS-2CD854F-E and DS-2CD883F-E
IQeye863N, IQeye865N, IQM30N, IQM31N, IQM32N and IQD32S
FCS-0071, FCS-1122, FCS-5061 and WCS-0050(Mainconsole only)
WV-SC384, WV-SC385, WV-SF332, WV-SF335E, WV-SW355(above add I/O),
WV-SW396
RV1WAD, RV01AD, RV01AT, RV04AD, RV1WAG, RV79AD, RV7RAD, RV7RAG,
RV81AD, RV81AG, RV84AD, RV84AM, RV84AV and RV87ZA
SNB-3002, SNO-7080RP, SNP-3371, SNP-3371TH, SPE-400
SND-3082 (F) and SNV-3082
FD8135H, FD8335H, IP8335H, PT8133 and PT8133W
B7210, D7110, F1100(Mainconsole only), F1105(Mainconsole only), F3101, F3106,
F3201, F3206 and F531E
Notice:
5. From DP v2.0, Mainconsole/NVRmini 2 (from v1.5)/Titan NVR (from v1.3) share same device pack.
6. Known issue: a. ACTi : KCM3211's PTZ only support Zoom and Focus. b. Arecont: AV20185 include AV20185DN, AV20185CO, AV20365 include AV20365DN,
AV20365CO c. Bullwark: BLW-IR230MP-SM 1920x1080 MJPEG Bit rate too high will affect camera parameter can not sync to camera information d. Forenix: not support search and auto detected (camera FW issue) e. Hikvision: 1.DS-2CD8254F-EIS、DS-2CD854F-E、DS-2CD883F-E can't set framerate 15~22
119 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 in Max resolution, DS-2CD8254F-EIS、DS-2CD854F-E、DS-2CD883F-E image broken when resolution over 1600x1200 f. IQinvision: IQM3xN series not support audio in M-JPEG g. Panasonic: WV-SC385 and WV-396 support continuous PTZ h. Samsung: SNP-3301, SNP-3370: H264 can't support QCIF resolution
7. Bug Fixed the bug thated:
Mainconsole: a. Fixed the bug that Vivotek IP7361 motion detection works failed when set motion area more than 2. b. Santec: SNC-4302
1080P and 800x600 don’t support flip and rotate, Model I/O revise and Quality setting fail issue
NVRmini 2: a. Fixed the bug that AV8185DN can't get correct video framerate, quality & compression after setting video parameter when adding the same model with a server over two times.
Titan NVR: a. Fixed the bug that Panasonic WV-SC385. The speed of PTZ is very slow in the Titan NVR.
Release Version v1.19.0 (2012/02/29)
Modules:
Device Pack v 1.19.0
Supported Systems:
MainConsole v 3.3.0 above
New Camera Supported:
120 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Dynacolor: iCANTEK:
Messoa:
Micronet:
Pelco:
Santec:
Truen:
V2 series iCanView322MP, iCanView340MP
NIC990PRO-HP
SP5523W, SP5563HTM, SP5581HDC, SP5582HTM, SP-5584HTM, SP5591HTM
SP5923,
IP110, SpectraIV-IP
SNC-3302, SNC-4302, SNC-5312IR, SNC-6302, SNC-6312IRH, SVS-3001
TCAM-5x10, TCS-2000
Notice: c. Firmware Upgrade
iCANTEK: iCanView332MP, iCanView362MP
Truen: TCAM-570 d. Known issue: i. Messoa: NIC990PRO-HP
Only support video and PTZ. Other parameters setting, audio and DI/DO are not available due to firmware issue. j. Pelco : IP110, SpectraIV-IP
Only support MPEG4 image, not support parameter setting. SpectraIV-IP only support
704x240. IP110 only support 704x480. k. Micronet: SP5923
1080P and 800x600 don’t support flip and rotate. l. Micronet: SP5581HDC
Not support talk. m. Santec: SNC-4302
1080P and 800x600 don’t support flip and rotate. n. Truen: TCAM-570
MJPEG not support audio. o. Truen: TCAM-2000
Not support below resolutions:
Composite NTSC 352x240, 720x240
HDMI 1080i60 352x240, 720x240, 640x360
Echo would occur after stop talk function e. Bug Fixed the bug thated: a. ACTi: KCM-5211 Auto-Focus behavior did not sync with camera web.
121 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 b. Vivotek: VS8401 would connect with incorrect channels. c. CNB: ISS2965x can’t Zoom In/Out by joystick. d. Corumcctv: MainConsole would hang and stop after disconnecting the video stream.
Release Version v1.18.0 (2012/01/03)
Modules:
Device Pack v 1.18.0
Supported Systems:
MainConsole v 3.3.0 above
New Camera Supported:
122 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Hikvision:
Lilin:
Sony:
Vision Hi-Tech:
Vivotek:
Notice:
DS-2CD783F-E, DS-2CD783F-EI, DS-2DF1-5702, DS-2DF1-570A,
DS-2DF1-5732, DS-2DF1-573A, DS-2DF1-57A
IPD2220ES, IPG1022ES, IPR320ESX, IPR722S, IPR7424/8ESX
SNC-EP521, SNC-EP550, SNC-EP580, SNC-ER550
VISION i series, VISION M3i series, VISION NVS102
IP8335H f. Bug Fixed the bug thated p. PELCO: D5118 cannot operate PTZ feature by joystick. q. PELCO’s cameras: The video format does not sync with web’s setting. r. Fine: TCP-690 cannot be connected. s. AXIS: P5534-E cannot set PTZ preset positions. t. iCANTEK: iCanView362MP, iCanView332MP :
The audio stream would cause IP+ crash. g. Known issue:
Lilin: IPG1022ES, IPD2022ES and IPR7424/8ESX
The audio inputs only support HTTP protocol.
Hikvision: DS-2DF1-57xx series
The H.264 stream displays not smoothly.
Release Version v1.17.0 (2011/12/01)
Modules:
Device Pack v 1.17.0
Supported Systems:
MainConsole v 3.3.0 above
New Camera Supported:
123 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi:
AMTK:
Etrovision:
Hikvision:
Panasonic:
UDP:
Vision Hi-Tech:
Vivotek:
Zavio:
KCM-5211E, KCM-5311E
AM2110D, AM2231D, AM2590D
EV8281U, EV8285Q, EV8286Q
DS-2CD753F-E, DS-2CD753F-EI, DS-2CD754F-E, DS-2CD754F-EI,
DS-2CD754FWD-E, DS-2CD754FWD-EI, DS-2DF1-572
WV-SF132, WV-SF135, WV-SW152/M, WV-SW155/M
IPE1100M, IPE3100, IPE3500, IPE4100, IPE5500, IPE6500, IPE7500
Vision Mi series
MD7560X
F3201, F7210
Notice: h. Bug Fixed the bug thated u. Mainconsole breakdown when closing and restarting Mainconsole after Onvif models operate
Start patrol. v. SAE-E588HDE18C can’t control Zoom In/Out by joystick. w. PELCO-D5118 doesn’t store the relative parameter of ptz speed after change it and restart
Mainconsole. i. Known issue:
Hikvision DS-2CD753-E, DS-2CD753-EI, DS-2CD754-E, DS-2CD754-EI,
DS-2CD754FWD-E, DS-2CD754FWD-EI do not support PTZ preset using RS-485. j. Firmware Upgrade:
Arecont: AV3135
Samsung: SNB-5000, SND-5080/F, SNP-5200H, SNV-5010, SNZ-5200
UDP: NVC1000
Release Version v1.16.0 (2011/11/04)
Modules:
Device Pack v 1.16.0
Supported Systems:
MainConsole v 3.3.0 above
New Camera Supported:
124 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Brickcom:
CNB:
Dahua:
Etrovision:
MD-100AP
IDC4050F, IDC4050IR, IDC4050VF, IDC4050VR, IGC2050F, ISMC1063x,
IS1765x, ISS2965x, ISSM2063x, IVC5055VF, IVC5055VR, IXC2050IR,
HDB3300N, HDB3300P, HDBW3300N, HDBW3300P, HF3110N, HF3110P,
HF3211P, HF3300N, HF3300N-W, HF3300P, HF3300P-W
EV3150A, EV3151, EV3151A, EV6150A-BI, EV6150A-CI, EV6151A, EV6153A,
EV6156A, EV6250A-EI/EO, EV6251A-FI/FO, EV6252A-GI/GO, EV6252A-GI/GO,
EV6353A-DO, EV6353A-EO, EV6353A-FO, EV6355A/AP-BO, EV6355A/AP-CO,
EV6551A/AP-BI, EV6551A/AP-CI, EV6551A/AP-DI, EV6552A/AP, EV6552R/RP,
EV6580A/AP-B/C, EV6581A/AP, EV6750, EV8150A, EV8180A, EV8180A-D,
EV8180F, EV8180Q, EV8180Q-D, EV8180U, EV8180U-D, EV8280U, EV8285U,
EV8383F, EV8580A-B, EV8580A-C, EV8580A-DB, EV8580A-DC, EV8580F,
EV8580Q-C, EV8580Q-DB, EV8580Q-DC, EV8580U-B, EV8580U-C, EV8580U-DB,
EV8580U-DC, EV8580U-DM, EV8580U-M, EV8581A-C, EV8581A-DB, EV8581A-DC,
EV8581Q-C, EV8581Q-DB, EV8581Q-DC, EV8581U-B, EV8581U-C, EV8581U-DB,
EV8581U-DC, EV8582A-D, EV8780A, EV8780U, EV8781A-C, EV8781A-DC,
Shany:
USAG:
Vivotek:
Samsung:
EV8781F, EV8781Q-C, EV8781Q-DC, EV8781U-C, EV8781U-DC, EV8781U-DM,
EV8781U-M, EV8782A, EV8782A-DB, EV8782Q, EV8782Q-DB, EV8782U,
EV8782U-DB
SNC-10XX, SNC-20XX, SNC-81XX, SNC-91XX, SNC-D1XX
US-AVC4-2-600NR-I2
IP8133W, IP8331, MD8562
SNV-7080, SNV-7080R
Notice:
1. Bug Fixed the bug thated:
AXIS P1346 : Support all of AAC audio codec setting.
Arecont AV2125: Fixed the bug that the image would turn to green when using UDP connection
Shany: Fixed the bug that 1080P resolution name.
Zavio D611E: Fixed the bug that connection issue
2. Known issue:
CNB: 2M pixel models do not support UDP connection.
Dahua: All models only support Pan & Tilt feature using RS-485 to control the external device.
Etrovision: xx8x/xx5x series do not support talk function, 8150A and related models do not
125 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0 support VGA resolution.
USAG: Does not support PTZ feature using RS-485.
Samsung: 3120x, 3430H, 5xxx and 7xxx series only support TCP connection.
3. Firmware Upgrade:
Samsung: SND-7080, SNO-5080R, SNP-3120, SNP-3120V, SNP-3430H, SNV-3120,
SNV-5080R
Release Version v1.15.0 (2011/10/03)
Modules:
Device Pack v 1.15.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0 & 3.5.10 & v 3.5.18
126 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
Arecont:
Probe:
AV20185DN, AV20365DN
PIC-500, PIC-501, PIC-H1310T, PIC-H2010T, PID-500, PID-501, PID-H1000,
PID-H2010T, PIK-H2010T, PIN-H1310T, PIN-H2010T, PIP-H1000, PIS-400,
PK-H1310T, PMI-400, PMI-403, PMI-410, PMI-H2000, PTI-400, PTI-401, PTI-402,
Shany:
Vivotek:
Zavio:
PTI-403, PTI-500, PTI-501, PTI-502, PTI-503, PTI-H1302, PTI-H2100
SNC-21X0, SNC-21XX, SNC-22XX, SNC-23XX, SNC-HD2XX, SNC-HD81X2,
SNC-HD91X2, SNC-HD91XX, SNC-RX01N
SD83x1E, SD83x2E, SD83x3E, VS8401
F3106, F7110
Notice:
4. New feature:
Onvif 1.02 PTZ feature is supported.
5. Bug Fixed the bug thated:
LevelOne FCS-5041: login in with wrong password will cause system crash.
6. Known issue:
7. Probe series don’t support IO feature/audio in.
8. Shany series will show B/W image when set camera parameter very low quality in MJPEG codec.
Release Version v1.14.0 (2011/09/02)
Modules:
Device Pack v 1.14.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0
New Camera Supported:
127 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi:
Arecont:
AXIS:
CORUM:
Forenix:
Messoa:
SONY:
UDP:
Vivotek:
KCM5211, KCM5311, KCM7211
AV1115, AV1125, AV2115, AV2125, AV3115, AV3125, AV5115, AV5125,
AV10115
M3114-VE, Q6035, Q6035-E
CS-190-IO, CS-190-IP, CS-190-IW, CS-265-IO, CS-265-IP, CS-265-IW,
CS-285-IP, CS-325-IO, CS-325-IP, CS-385-IO, CS-385-IP, CS-390-IO,
CS-390-IP, CS-410-IP, CS-410-IW, CS-415-IP, CS-415-IW
ACDV-3VM501, AEP-Q2018H-IP, AEP-Q2018HW-IP, AEP-Q2026H-IP,
AEP-Q2026HW-IP, AEP-Q2036H-IP, AEP-Q2036HW-IP, ASP-PTIR737-IP,
ASP-PTIR737-LA-IP, ATCP-IRH5030C, ATCP-IRH5040C, ATCP-MH802,
ATCP-MH802DN, ATCP-MH802DN/WI, ATCP-MH802WI, ATCP-VM501,
B0100, B1100, C1100, C1100-W, D0100, D1100, D2100
NIC910HPRO, NIC930HPRO, NIC950HPRO
SNC-EP520, SNC-ER520, SNC-ER521, SNC-ER580
IPE3500M, NVC4000, NVC4000-R12, NVC4000-R40
IP8352, PZ81x1, PZ81x1W
Notice:
9. New feature:
Onvif 1.02 support is officially released on Device Pack 1.14.0 but non-support PTZ feature.
ACTi
TCD2500 supports PTZ feature.
Grandstream
GXV series supports talk and PTZ features
10. Bug Fixed the bug thated:
PANASONIC WV-NM100 has probabilities cause system crash.
ACTi ACM1431 Audio disabled issue.
Release Version v1.13.0 (2011/08/02)
Modules:
Device Pack v 1.13.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0
New Camera Supported:
128 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi:
AXIS:
Brickcom:
Everfocus:
Grandstream:
Panasonic:
Pelco:
Samsung:
Vivotek:
KCM7111
M5013, M5014, P5512, P5512-E, P5522, P5522-E
VS-04A
EQN2200, EQN2201
GXV-3501, GXV-3504, GXV-3601, GXV-3601HD, GXV-3601LL, GXV-3611HD,
GXV-3611LL, GXV-3615, GXV-3651, GXV-3662HD
WV-SW352, WV-SW355
D-5118
SNP-3301, SNB-7000
FE8171V
Notice:
11. New feature:
AXIS
P1346, P5534 support AAC codec
Vivotek
VS8102 supports continuous PTZ
12. Bug Fixed the bug thated:
Truen
Adjust TCAM-570 PTZ moving distance sync with web client.
SAE
DR-E588-HD18 can’t control PTZ by joystick.
AXIS
Supported Q7401 to 64 preset point.
Fine
MainConsole will hang out when single TCP-VM501 setup four connections at the same time.
Release Version v1.12.0 (2011/07/01)
Modules:
Device Pack v 1.12.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0
New Camera Supported:
129 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Everfocus:
Samsung:
VIVOTEK:
EAN3200, EHN3200, EDN3240, EZN3240
SNB-1000, SND-7080, SNO-5080R, SNP-3120V, SNP-3370, SNP-3430H,
SNP-5200, SNP-5200H, SNV-5010, SNV-5080R, SNZ-5200
FD8162, FD8361L, FD8362, FD8362E, SD8362E
Notice:
13. Bug Fixed the bug thated:
Fixed the bug that Sony preset name length issue.
Fixed the bug that Panasonic WV-SP105 auto detect failure.
Release Version v1.11.0 (2011/05/31)
Modules:
Device Pack v 1.11.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0
New Camera Supported:
130 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi:
AXIS:
CTCunion:
Panasonic:
Samsung:
Santec:
Sony:
Videosec:
VIVOTEK:
UDP:
KCM5111, TCM4001
P3346, P3346-V, P3346-VE
DVS-8501E, DVS-8504E
DG-SF334, WV-SF342, WV-SF346
SNB-5000, SND-5080/F, SNV-3120, SNV-5080
SNC-3903M, SNC-5321MIR, SNC-6163ID, SNC-6223MIR, SNC-6303M,
SNC-P3603M
SNC-DH110/B, SNC-DH110/W, SNC-DH110T/B, SNC-DH110T/W
ICS-13, ICS-20F, ID-20
IP8362, MD7530, VS8801
NVC1000
Notice:
1. Bug Fixed the bug thated:
Fixed the bug that Dallmeier preset function dump
ONVIF check startcode if using RTSP for H264 codec
Fixed the bug that Vivotek IP 7133 can’t use AAC codec issue
Release Version v1.10.0 (2011/04/15)
Modules:
Device Pack v 1.10.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1
131 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
Arecont:
AXIS:
AV1325, AV2825, AV8185DN, AV8365DN
P1347, P1347-E, P5532, P5532-E, P5534-E, Q1921, Q1921-E
D-link:
Fine:
IQinvision:
DCS-6511, DCS-7410
EDH-02H, SP-PTIR737-LA-IP, TCP-IR590-WD30, TCP-IR590-WD50,
TCP-IRH5030C, TCP-IRH5040C
IQ732N
Panasonic:
Sony: vForge:
VIVOTEK:
WV-SC384, WV-SC385, WV-SW395
SNC-DH210/B, SNC-DH210/W, SNC-DH220, SNC-DH220T
VFA1
FD8133V, FD8134V, IP8151P, IP8162, IP8162P, MD7560
Notice:
1. Bug Fixed the bug thated:
ACTi CAM7301: auto detection failure issue.
Arecont Camera: auto detection failure issue.
Axis Q7401 sync preset point issue.
Dynacolor NH061: broken image issue (H.264/1280x720).
2. Bosch speed dome V4G series supported by Axis video server (test by model Q7404).
Release Version v1.9.0 (2011/02/28)
Modules:
Device Pack v 1.9.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1
132 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
Arecont:
AXIS:
AV1315, AV2815
212 PTZ-V, 215 PTZ-E, 240Q Blade, 241Q Blade, 241S Blade, 243Q Blade, P1343-E,
Lilin:
Panasonic:
Sony:
P1344-E, P1346-E, Q1755-E, Q6034-E
IPS025, IPS030, IPS035, IPS125, IPS130, IPS135, IPS203, IPS212
WV-SP102, WV-SP105
SNC-CH260, SNC-CH280, SNC-DH210T/B, SNC-DH210T/W, SNC-DH260,
SNC-DH280
Notice:
1. Dallmeier DDZ40SM-HD: Add TCP connection, DI/DO and two-way audio.
2. Bug Fixed the bug thated: Panasonic WV-NS202A auto detection failure .
Release Version v1.8.0 (2010/12/31)
Modules:
Device Pack v 1.8.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4
133 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
ACTi:
Hikvision:
TCM7811,
DS-2CD7133-E, DS-2CD7153-E
Levelone:
Lilin:
Sony:
FCS-0040, FCS-3081, FCS-5051, FCS-5041, WCS-0040
IPD112ESX, IPD552EX, IPR414ESX, IPR418ESX, IPR454, IPR458
SNC-CH110/B, SNC-CH110/S, SNC-CH220
Notice:
1. Bug Fixed the bug thated: Users can adjust Arecont camera’s resolution by setting four video coordinate values. (Not support Arecont 8000 series cameras.)
Release Version v1.7.0 (2010/11/12)
Modules:
Device Pack v 1.7.0
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4
134 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
ACTi: ACM5811, ACM7511, TCD2100, TCM3001, TCM3011, TCM3401, TCM3411,
TCM4201, TCM5001, TCM7011
ARM:
Camtron:
CryptoTelecom:
Dallmeier:
MP13DDNWD, MP13VPDN
IPH3611N, NVE1000A, NVE2000A, NVE4000A
S-152
DDZ40SM-HD
Panasonic:
Samsung:
Sony:
Truen:
VIVOTEK:
BL-C210, BL-C230, WJ-GXE500, WV-SF332, WV-SF335, WV-SF336, WV-SP302,
WV-SP305, WV-SP306
SNS-100
SNC-CH120, SNC-CH160, SNC-CH210/B, SNC-CH210/S, SNC-DH120,
SNC-DH120T, SNC-DH140T, SNC-DH160, SNC-DH240T
TCAM-570
FD8133, FD8134, IP8132, IP8151, IP8330, IP8332, PZ7132, SD81X1
Notice:
1. Bug Fixed the bug thated: Panasonic WV-NP502 won't show error message when switching video codec to H.264.
Release Version v1.6.0 (2010/10/7)
Modules:
Device Pack
Supported Systems:
MainConsole v 1.6.0 v 3.3.0 & v 3.3.2 & v 3.3.12
135 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
Arecont:
Camtron:
AV2805
CMNC-130, CMNC-200, CTNC-5358D, HLC-81A D/P, HLC-83V, HLC-83V/W
HLC-84V, HLC-84V/W
Honeywell: ACUIX, HCD554IP, HD3MDIP, HD4DIP, HD4MDIP, HNVE1
PELCO:
Pixord:
IX10
P600, P606, PB630, PD634, PL621, PV6901
SAE: ANNA 200M, E588HDE18C, E688HDE10
Notice:
1. Bug Fixed the bug thated: Fine WB-8211SDU can use PTZ function.
Release Version v1.5.0 (2010/8/31)
Modules: v 1.5.0 Device Pack
Supported Systems:
MainConsole
New Camera Supported: v 3.3.0 & v 3.3.2 & v3.3.11
136 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
Brickcom:
Fine:
CB-100A, CB-100Ae, FB-100A, FB-100Ae, FD-100Ae, WCB-100Ae,
WFB-100Ae
CDV-3VM301, CDV-3VM501, CDV-3VWD960, CDV-3VWD960H, EP-601HW,
EP-908HW, EP-936HW, EP-HTQ935, EP-Q2018H-IP, EP-Q2018HW-IP,
EP-Q2026H-IP, EP-Q2026HW-IP, EP-Q2036H-IP, EP-Q2036HW-IP,
MD-D1612, SP-PTIR737-IP, TCMA-99, TCMP-99, TCP-IPWD690,
TCP-IPWD700DN, TCP-IRV540, TCP-IRV560/50M, TCP-MH802, TCP-VM201,
TCP-VM501, WB-H811, WB-H814
DS-2CD702NF-E, DS-2CD702PF-E, DS-2CD712NF-E, DS-2CD712PF-E, Hikvision:
DS-2CD732F-E, DS-2CD792NF-E, DS-2CD792PF-E, DS-2CD802N-IR1,
DS-2CD802N-IR3, DS-2CD802N-IR5, DS-2CD802P-IR1, DS-2CD802P-IR3,
DS-2CD802P-IR5, DS-2CD832F, DS-2CD832F-E, DS-2DF1-401H,
DS-2DF1-402H, DS-2DF1-601H, DS-2DF1-602H, DS-2DF1-603H,
DS-2DF1-604H, DS-2DF1-605H, DS-2DF1-606H, DS-2DF1-607H,
DS-2DF1-611H, DS-2DF1-612H, DS-2DF1-613H, DS-2DF1-614H,
DS-2DF1-615H, DS-2DF1-616H, DS-2DF1-617H, DS-2DM1-602H,
DS-2DM1-603H, DS-2DM1-604H, DS-2DM1-612H, DS-2DM1-613H,
DS-2DM1-614H, DS-6101HFI-SATA, DS-6104HCI, DS-6104HCI-SATA
NetworkCamera: GE-100-CB, GP-100-CB, WGE-100-CB, WGP-100-CB
PELCO: ID10, ID30, IDE20, IDS0, IE10, IE30, IEE10, IEE20, IES0, IMS0, IX30,
IXE20, IXS0
Sony: SNC-RS44N, SNC-RS44P, SNC-RS46N, SNC-RS84N, SNC-RS84P,
SNC-RS86N, SNC-RS86P, SNT-EP104, SNT-EX101
IBF-211, ID-209, IDA-210, IP-206M, IS-240 Videosec:
Notice:
1. Bug Fixed the bug thated: SANYO-HD5600P can change resolution.
2. Onvif supported: AXIS_P3301, Bosch_NWC-0455
Release Version v1.4.0 (2010/8/9)
Modules: v 1.4.0 Device Pack
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2 & v 3.3.11
137 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
iCanTek: iCanView362MP, iCanView332MP, iCanView350MP, iCanServer612
SANTEC: SNC-3901MDN, SNC-P3601M
Release Version v1.3.0 (2010/7/21)
Modules: v 1.3.0 Device Pack
Supported Systems:
MainConsole
New Camera Supported: v 3.3.0 & v 3.3.2
Copyright © 2014 NUUO Inc. All rights reserved.
138 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
ACTi:
Arecont:
TCM-1511
AV10005
AXIS: M1103, M1113, M1054, Q6034
Panasonic: BB-HCM547A, BB-HCM701
SANTEC:
Sony:
SNC-6201M, SNC-5211MIR
SNT-EX154, SNT-EX101E, SNT-EP154, SNC-CH140, SNC-DH140, SNC-CH180,
SNC-CH240, SNC-DH240, SNC-RH164, SNC-RS46P
Notice:
1. Sony SNC-CH240, SNC-DH240 do not support resolution over 1920x1080
Release Version v1.2.0 (2010/6/8)
Modules: v 1.2.0 Device Pack
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2
139 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Features
1. Support Arecont I/O function
New Camera Supported:
ACTi: ACM-3601, ACM-3603, ACM-3701, ACM-3703, ACM-4001
TCD-2500, TCM-4101, TCM-5312, TCM-1231, TCM-1232
Arecont:
AXIS:
TCM-5601, TCM-5611, TCM-3511, TCM-7411
AV3135, AV1310, AV2110, AV3110, AV5110
P1346, P5534, Q1910, Q1910-E, M1104, M1114
M3203, M3203-V, M3204, M3204-V, P3304, M7001
CNB:
IQeye:
IDC4000T, IVC4000T
IQ040S, IQ041S, IQ042S, IQD30S, IQD31S
IQD40S, IQD41S, IQD42S, IQ540S, IQ541S, IQ542S
Panasonic: BB-HCM100, BB-HCM110, BB-HCM580, BL-C140A
Samsung: SNB-2000, SNB-3000, SND-3080, SNV-3080
Sanyo: VCC-HD2500, VCC-HD2500P
Sony:
StarDot:
SNT-EX104, SNC-DH180, SNC-RH124
SDH500BN, SDH500B, SDH300B, SDH130BN, SDH130B
SDH500VN, SDH500V, SDH300V, SDH130VN, SDH130V
Notice:
1. Bug Fixed the bug thated: Fixed the bug thated MainConsole unexpected crash issue with
Mobotix Q24M-sec camera.
Release Version v1.1.1 (2010/5/12)
Modules: v 1.1.1 Device Pack
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2
140 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
CNB: IBE3815NVR, IBE3815PVR, IBE5810NCR, IBE5810PCR
IDP4000VD, IDP4000VR, IDP4030VR, IGP1000, IGP1030
IJB2000, INS2000, IPM3063N, IPM3063P, ISMC1063N, ISMC1063P
ISS2765NW, ISS2765PW, IVP4000VR, IVP4030VR
LevelOne: FCS-7111
Release Version v1.1.0 (2010/5/4)
Modules: v 1.1.0 Device Pack
Supported Systems:
MainConsole v 3.3.0 & v 3.3.2
Copyright © 2014 NUUO Inc. All rights reserved.
141 / 142
NVR Device Pack Release Note
NUUO version 3.7.0
New Camera Supported:
ACTi: AMU-9401, AMU-9711, TMU-9811, TMU-9911
Bosch: NW-455
Brickcom: WCB-100A, WFB-100A, FD-100A
CISCO: WVC210
Dynacolor: nNH221, nNH061, V1, V6
Everfocus: EAN-850A, EZN-850, EDN-800, EDN-850H, EAN900, EAN800AW, EAN800A
EVS200A, EVS200AW, EPN2700, EPN3100, EPN3600
LevelOne: FCS-3031, FCS-3051, FCS-1131, FCS-1141, FCS-3071, FCS-0030, WCS-0030
FCS-1121, FCS-3061, FCS-4020, FCS-1040 v3.0, WCS-2040 v3.0, FCS-1151
MOBOTIX: D24M-Basic, D24M-IT, D24M-Sec
Panasonic: BB-HCM705A, BB-HCM715A, BB-HCM735A
Samsung: SNP-3300A
SanTec: SNC-390DN/W, SNC-521IR/W, SNC-565IR/W, SNC-620/W, SNC-670ID/W
Sanyo: VCC-HD3500, VDC-HD3500, VDC-HD3500p, VCC-HD2100, VCC-HD2100P
VCC-HD2300, VCC-HD2300P, VDC-HD3100, VDC-HD3100P
VCC-HD3300, VDC-HD3300, VDC-HD3300P, VCC-HD4600, VCC-HD4600P
VCC-HD5400, VCC-HD5400P, VCC-HD5600, VCC-HD5600P
StarDot: SD-130, SD-300, SD-500, SDEXP4, SDEXP2
VIVOTEK: IP8161, VS8102, FD8161, FD8361
Notice:
1. Only compatible with NUUO MainConsole v3.3.0 above
2. Must install Main Console software before install device pack v1.1.0
142 / 142
Copyright © 2014 NUUO Inc. All rights reserved.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
advertisement