Audiovox PPC 5050 User`s manual

PPC-5050A
15” TFT Panel PC Ver 1.0
Manual Revision 1.0
October 7,2002
Copyright Notice
©Copyright 2002 by ICP Electronics Inc. All Rights Reserved.
Revision: 1.0. Oct., 7 2002.
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the
part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
Trademarks
PPC-5050A is a registered trademark of ICP Electronics Inc. IBM PC is a registered
trademark of International Business Machines Corporation. Intel is a registered
trademark of Intel Corporation. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks of
their respective companies. If you have any questions or need other information,
please visit to our web site.
http://www.iei.com.tw
1
Revision History
Revision
1.00
Revision Note
Initial release of the PPC-5050A user’s manual
Date
Oct. 7 20002
Note:
The author assumes no responsibility for any errors or omissions that may appear this
manual nor does the author make a commitment to update the information contained
herein.
2
Table of Contents
1. INTRODUCTION....................................................................................................4
1.1 CHECKLIST ............................................................................................................4
1.2 FEATURES ..............................................................................................................4
1.3 SPECIFICATIONS.....................................................................................................5
1.4 MECHANICAL DIMENSION .................................................................................9
2. SYSTEM SETUP ...................................................................................................10
2.1 THE REVERSE SIDE OF PPC-5050A..................................................................10
2.2 THE REVERSE SIDE OF THE REAR CABINET ...................................................... 11
2.3 THE SIDE VIEW OF PPC-5050A........................................................................12
2.4 POS-566/370 CPU BOARD INSTALLATION .......................................................13
2.5 POWER SUPPLY INSTALLATION ..........................................................................14
2.6 DRIVE DISK I NSTALLATION ...............................................................................15
2.6.1 FDD Installation......................................................................................15
2.6.2 HDD Installation .....................................................................................16
2.6.3
CD-ROM Installation...........................................................................17
2.7 PANEL MOUNTING ............................................................................................18
2.8 WALL MOUNTING .............................................................................................19
2.9 ARM MOUNTING ...............................................................................................20
2.10 RACK MOUNTING ...........................................................................................21
APPENDIX A EXPLODED DIAGRAM ..............................................................22
APPENDIX B
USER MODE OSD FEATURE DESCRIPTION .......................23
APPENDIX C
DISPLAY INTERFACE................................................................26
APPENDIX D
TOUCH PANEL CONTROLLER ...............................................27
3
1. Introduction
The PPC-5050A, 15" LCD TFT Panel PC, takes advantages of modern flat-panel
display, POS-566/370 CPU board, drive spaces and power supply for minimum size.
It is an IBM PC/AT compatible computer specially designed to meet the applications
for industrial environment.
1.1 Checklist
Item
1
2
3
4
5
6
7
8
9
10
11
12
12
13
14
15
16
17
18
19
Description
Y Cable
Power Cable
Wall Mounting kit
BOLT M4*8
Mounting Clip
Round Head Screw M5*50
Round Head Screw M3*6
Flat Head Screw M3*6
Screw Accessories (19600-000103)
Screw Accessories (19600-000104)
Screw Accessories (19600-000105)
Screw Accessories (19600-000063)
A49
SLIM-05
JUMPER Pitch:2.0
POS-566/370 User’s Manual
PPC-5050 User’s Manual
CD-ROM Driver
Touch Panel Pen (Option)
Touch Panel Driver (Option)
Qty.
1
1
1
4
10
10
10
5
1
1
1
1
1
1
10
1
1
1
1
1
1.2 Features
CPU Board
PPC-5050A is designed for POS-566/370 CPU board. The POS-566/370 board is a
LPX specification board, which equipped with high performance socket 370 Celeron
Pentium III® CPU, LCD/CRT and 10/100Mbps Ethernet, designed for the system
manufacturers, integrators, or VARs to provide all the performance, reliability, and
quality.
LCD Display
4
The PPC-5050A is equipped with a 15" TFT LCD.
Power Supply
The standard industrial power supply of PPC-5050A is equipped with ACE-916AP.
Touch Screen (option)
Dynapro resistive touch screen.
HDD, FDD & CD-ROM
It is suggested to be equipped with one 2.5” internal HDD, one slim FDD, and one
slim CD-ROM.
1.3 Specifications
z
z
z
z
Disk Drive Bay: Support one 2.5" HDD, one slim FDD, and one slim CD-ROM.
Best solution for Panel mount man machine interface.
Dimensions : Front Panel: 410mm x 309mm x 9mm (WxHxD)
Cabinet: 383.6mm x 282.6mm x 97.6mm (WxHxD)
LCD Display: TTL LCD connector interface to support screen reverse function.
Display Model
CHI MEI
Display Type
LCD model
Resolution
Display colors
Brightness
LCD MTBF
Backlight MTBF
Supply Voltage
15” TFT color
M150X2-T05
1024x768
262,144 color
250 cd/m2
50,000 hrs
50,000 hrs
3.3V
z
Dynapro Touch Screen (option)
Type: Analog Resistive
Resolution: Continuous
Light transmission: Typical value 75%
Surface Hardness: 4H (Test condition: ASTM D3363-92A)
8-wire touch screen
Support driver: Supports Linux,MS-DOS,Windows 3.1/95/
98/CE,ME/2000/NT,OS/2,MAC,etc.
z
Environmental specifications
5
Operating Temperature : 0 ~ 50℃
Relative Humidity: 5~85% @40℃ , non-condensing
Vibration: 5 to 17 Hz, 0.1"double-amplitude displacement,
17 to 500 Hz, 1.5 G peak to peak.
z
Industrial Power Supply: ACE-916AP series Power Supply
High reliability triple outputs switching Power Supply with height 40.6mm only
Standard Power Supply: ACE-916AP
Optional Power Supply: ACE-916A, ACE-816A/ AP and ACE-815T
Operating temperature: -0°C to 50°C
Vibration: 10-55Hz at 2G 3 min. period, 30 min. along X, Y, and Z axis
Shock: 10G for 20ms once on each X, Y, and Z axis
Safety: meet UL1950/TUV: EN60950
EMI: meet FCC class B /CISPR:EN 55022 class B/CE: Harmonic EN61000-3-2
Warning: Whenever you need to take off a part for either maintenance or
upgrading purpose, you should switch off the power supply and unplug the
power cord first.
z
Specifications of POS-566 CPU Board:
The POS-566/566L 450MHz K6-3 / Pentium Processor Multimedia POS
Control SBC provides the following specifications:
•
®
®
®
®
®
CPU: Pentium MMX up to 233Mhz, AMD K6 /K6 -2/K6 -3 up to
450MHz, IDT C6, Cyrix 6x86MX, etc. Processor
•
RAM: 3x DIMM sockets up to 768MB SDRAM
•
Cache memory: 512KB Pipelined Burst SRAM on board
•
Bus: PCISA bus expansion to support ISA and PCI bus signal
•
Chipset: Ali 5, support 100MHz CPU clock
•
LCD/CRT Controller: CHIPS 65555 2MB EDO RAM on board
•
Support 3.3V or 5V flat panel.
•
Support Mono, Color STN, TFT, EL,.. wide range flat panel.
•
Optional One Channel or Two Channels LVDS module.
•
10/100Mbps Ethernet Controller: Realtek RTL8139 IEEE 802.u 100
BASE-TX standard Dual Auto-sensing interface to 10MBps or 100MBps
networks
6
RJ45 connector for 10BASE-T and 100BASE-TX
Full duplex capability, full software driver support.
•
Creative Sound Blaster 16 compatible and Roland MPU401 UART
Mode compatible
•
Four high speed Serial ports : three RS-232C, one RS-232C, or
RS-422/485 Port
•
Parallel Ports : Two SPP/EPP/ECP Parallel Ports
•
Enhanced IDE Interface :
One 44-pin Header for 2.5” HDD
One 40-pin Header for 3.5” HDD
•
PCISA
•
Isolated Digital I/O: 4 Digital Inputs and 4 Digital Output channels
•
IrDA port: Support Serial Infrared (SIR) and Amplitude Shift Keyed
IR (ASKIR) interface.
•
Two USB ports: Support dual USB ports for future expansion.
•
Watchdog timer: Can be set by 1, 2, 10, 20, 110 or 220 seconds period.
Reset or NMI is generated when CPU does not periodically trigger the timer.
•
TM
Bus Expansion to support ISA and PCI bus signal
2
TM
Function: A special designed 1Kbit EEPROM (non volatile
E Key
memory) provided to accept read/ write data by customer’s program. It is
useful to store system ID, Password, Critical Data on the board.
•
Keyboard connector
•
Mouse: PS/2 Mouse Port on-board.
•
Power Consumption: +5V/5.5A (AMD K6-2 350MHz, 384MB SDRAM)
+12V: 170mA , -12V : 60mA
z
•
Support ATX and AT power supply
•
Operating Temperature: 0 ° ~ 60° C ( CPU needs Cooler)
•
Operating Humidity: 5-95% non-condensing
Specifications of POS-370 CPU Board:
The POS-370 socket 370 Celeron Pentium III Processor Multimedia POS
Control SBC provides the following specifications:
•
®
CPU: Celeron & Pentium III Processor
•
RAM: 2x DIMM sockets up to 1GB SDRAM.
7
•
Bus: PCI bus expansion to support .
•
Chipset: SIS630, support 133MHz CPU clock
•
LCD/CRT Controller: On chip SIS300
•
Support 3.3V or 5V flat panel.
•
Support Mono, TFT, EL... wide one channel that panel.
•
Optional One Channel or One Channel LVDS module.
•
10/100Mbps Ethernet Controller: On chip SIS900 LAN BASE-TX
standard Dual Auto-sensing interface to 10MBps or 100MBps networks
RJ45 connector for 10BASE-T and 100BASE-TX
Full duplex capability, full software driver support.
•
On CHIP AC97 SIS 7018
•
Four high speed Serial ports : three RS-232C, one RS-232C, or
RS-422/485 Port
•
Parallel Ports : Two SPP/EPP/ECP Parallel Ports
•
Enhanced IDE Interface : (DMA 66)
Two 40-pin Header for 3.5” HDD
•
PCI Bus Expansion to support PCI bus signal
•
Isolated Digital I/O: 4 Digital Inputs and 4 Digital Output channels
•
IrDA port: Support Serial Infrared (SIR) and Amplitude Shift Keyed
IR (ASKIR) interface.
•
Five USB ports: Support dual USB ports for future expansion.
•
Watchdog timer: Can be set by 1 min.(min.) period.
•
Keyboard connector
•
Mouse: PS/2 Mouse Port on-board.
•
Power Consumption: +5V/6.5A (see POS-370 manual))
•
Support ATX and AT power supply
•
Operating Temperature: 0 ° ~ 60° C ( CPU needs Cooler)
•
Operating Humidity: 5-95% non-condensing
8
1.4 Mechanical Dimension
Front Panel: 410mm x 309mm x 9mm (WxHxD)
Cabinet: 383.6mm x 282.6mm x 97.6mm (WxHxD)
9
2. System Setup
The PPC-5050A, 15" LCD TFT Panel PC, is provided complete kit for your operation.
The following sections of this chapter will help your installation and maintenance.
2.1 The Reverse Side of PPC-5050A
The below diagram shows the reverse side of PPC-5050A. For maintenance,
installation or upgrade, you have to remove the back cover first by unfastening 9
screws as the diagram shown.
Warning: Before any installation/un-installation, please notice any
effects of static electricity.
10
2.2 The Reverse Side of the Rear Cabinet
The below figure indicates the reverse side of the rear cabinet.
OSD
COM 4
COM 3/RS422/RS485
PRINTER 2
PCI add-on card
MIC
SPEAKER
LINE-IN
ACP POWER
INPUT
110V/230V
SWITCH
VGA
COMPACT FLASH
PRINTER 1
COM 2
COM 1
POWER SW
KEYBOARD
USB PORT
LAN
11
2.3 The Side View of PPC-5050A
One FDD and CD-ROM are accessible for your operation on the driver frame.
FDD
CD ROM
12
2.4
POS-566/370 CPU Board Installation
To install the POS-566/370 CPU Board, you have to place the board into the cabinet
and then fasten it by four screws.
13
2.5
Power Supply Installation
The standard Power Supply for PPC-5050A is ACE-916AP, which has to be fastened
to the power bracket by 2 screws , and to be installed in the cabinet by fastening 3
screws as below diagram shown.
Output Spec. at 50°C
Model
ACE-916AP
ER
W
O
P
BR
KE
AC
T
Input Voltage
Max Output
+5V +12V –12V
16A
6A 0.3A
90V to 264VAC
AC
E-
91
6A
P
14
2.6
Drive Disk Installation
Following sections will introduce you how to install HDD, FDD and CD-ROM.
For the HDD, FDD and CD-ROM are installed in the cabinet, thus you have to open
the back cover first if you want to install , upgrade or replace them.
2.6.1 FDD Installation
It’s very easy to install the FDD. First, fasten the FDD to the Floppy Chassis by 4
screws, then fasten it with the Floppy Adapter to the drives shelf by 2 screws.
FLOPPY ADAPTOR
FD
D
FDD BRACKET
15
2.6.2 HDD Installation
To install the HDD, you have to assemble the HDD to the HDD bracket first.
fasten the HDD bracket to the drives shelf by 4 screws.
HDD BRACKET TOP
HDD
MOUNT STRIPS
HDD BRACKET BOTTOM
16
Then,
2.6.3 CD-ROM Installation
To install CD-ROM. You have to assemble the CD-ROM into the bracket, then
fasten the CD-ROM Adaptor to the CD-ROM. Finally you have to fasten this unit to
the drives shelf.
2-M2*6
M3*6
2-M2*2
CD-ROM Adaptor
CD
-R
O
SPACER
M
2-M2*3
17
2.7
Panel Mounting
PPC-5050A is designed for panel mounting. Before mounting the PPC-5050A into
panel, you have to check the cut out dimension first. Then mount it into panel by
four supporters. Please refer to diagrams below.
286.0
387.0
UNIT:mm
THE DIMENSION IS FOR PANEL MOUNTING
(The flat panel thickness is 6mm or
18
less than 6mm)
2.8
Wall Mounting
PPC-5050A is suitable for Wall mount.
TO
E
TH
LL
WA
TO
TO
LL
WA
E
TH
L
AL
W
E
TH
TO
E
TH
LL
WA
19
2.9 Arm Mounting
PPC-5050A is not only suitable for panel mounting but also for 75/100mm interface
pads for arm mounting; and the specification conform to the proposed VESA
standard.
100
75
75
100
88
20
2.10
Rack Mounting
DM/SRM/PPC serial product provide option rackmount kit for industrial Rack. The
following diagram shows how to mount DM/SRM serial product onto the 19" Rack.
STEP 2
STEP 1
Rackmount-Kit
21
Appendix A
Exploded Diagram
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DESCRIPTION
BACK COVER
HDD BRACKET (TOP)
HDD BRACKET (BOTTOM)
FDD BRACKET
CDROM BRACKET
DRIVES SHELF
REAR BRACKET
REAR BRACKET
REAR CARD FRAME
VGA BRACKET
FRONT BRACKET
15” TFT LCD
TOUCH PANEL HOLDER
TOUCH PANEL
FRONT PANEL
22
Q’TY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Appendix B
User Mode OSD Feature
Description
z
Auto-Adjustment
This feature will automatically adjust the H/V position, frequency, phase, and
black level.
z
Auto Phase
This feature will automatically adjust the sampling.
z
Brightness
This option is used to adjust the brightness of screen. This function will adjust the
offset value of ADC. Setting this value too high or too low will decrease the
quality of image.
z
Contrast
This option is used to adjust the contrast level on the screen, and will adjust the
gain value of ADC. Adjusting this value too high or too low will decrease the quality
of image.
23
z
DOS/GFX
This option is used to select VGA input signal in either text or graphic mode.
(This option is only available on resolution of 720/640x400 or 720/640x350). 400 and
350 standard IBM modes have the same Hsync. and Vsync. values, and AV-9261
MPU can not differentiate between them automatically, so the user should adjust them
manually to match the proper VGA mode .
z H. Position
This option is used to adjust horizontal display position of image.
z V. Position
This option is used to adjust vertical display position of image.
z
Language
This option is used to select the language used on the OSD display. AV-9261 can
support 2 languages on the OSD display. English is the default language.
24
z Revert
This option is used to reset the original parameters to the factory’s OSD data area of
the system EEPROM 24c16 device in order to re-initialize the AV-9261 system. When
a user over-adjusts the OSD data and sees no improvement in the quality, then the user
can select this feature and MPU will reload default BIOS setting and re-initialize the
system.
z Save
This option is used to save the parameters into the EEPROM 24c16 system’s user
OSD adjustment data area and close the OSD. Whenever the user adjusts any
parameters, this option will save the changed data on to the EEPROM so that the
MPU will use the stored data to initialize the AV-9261 system on future re-boots.
z
Main Menu
Each level of the OSD has an item named Main Menu, which allows the user to
exit the current level and return to the main menu.
z
Exit
Press the EXIT key to exit the OSD menu when you are finished.
25
Appendix C
Display Interface
For POS-370/566
D
LC
I NV
ER
TE
61
-92
V
A
R
OS
D
6
0/ 5
37
S
PO
26
6
Appendix D
Touch Panel Controller
The optional touch screen provides RS232 interface and the controller of
eGalax are as the below figure shown.
T
To
c
ou
e
an
hP
l
E
RC
U
O
RS
T
O
oP
WE
V
+5
To
RS
2
-2 3
Pi
ea
nH
r
de
27
Touch Panel
Control Board