IMPORTANT SAFETY INSTRUCTIONS
Notice to Installers
The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so.
Quick Reference Guide
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be
grounded as close as practical to the point of entry of the cable
into the building. For products sold in the US and Canada, this
reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper
grounding of the coaxial cable shield.
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back). No user-serviceable parts
inside. Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol is intended to alert you that uninsulated voltage
within this product may have sufficient magnitude to cause
electric shock.Therefore, it is dangerous to make any kind of
contact with any inside part of this product.
Ce symbole a pour but d’alerter toute personne qu’un contact
avec une pièce interne de ce produit, sous tension et non isolée,
pourrait être suffisant pour provoquer un choc électrique. Il est
donc dangereux d’être en contact avec toute pièce interne de
ce produit.
Cisco Explorer 8640HD, 8642HD, 8650HD,
and 8652HD High-Definition DVR Set-Tops
This symbol is intended to alert you of the presence
of important operating and maintenance (servicing)
instructions in the literature accompanying this product.
Ce symbole a pour but de vous avertir qu’une
documentation importante sur le fonctionnement et
l’entretien accompagne ce produit.
Explorer 8652HD
20080814_Installer820
CH+
VOL-
VOL+
POWER
1) Read these instructions.
Outdoor Grounding System
Handling Disposable Batteries
2) Keep these instructions.
If this product connects to an outdoor antenna or cable system, be sure
the antenna or cable system is grounded (earthed). This provides some
protection against voltage surges and built-up static charges.
This product may contain disposable batteries. Heed the following warning
and follow the Safety and Disposal instructions below.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990,
provides the following information:
6) Clean only with dry cloth.
• Grounding of the mast and supporting structure
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
• Grounding the lead-in wire to an antenna discharge unit
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
• Location of the antenna-discharge unit
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
• Size of the grounding conductors
• Connection to grounding electrodes
• Requirements for the grounding electrodes (see the following antenna
grounding diagram as recommended by NEC ANSI/NFPA 70)
LIST
VIDEO IN
• Insert batteries correctly. There may be a risk of explosion if the batteries
are incorrectly inserted.
• Please follow instructions provided for charging ‘rechargeable’
batteries.
• Replace batteries with the same or equivalent type that we
recommend.
• Do not expose batteries to excessive heat (such as sunlight or fire).
• The batteries may contain substances that could be harmful to the
environment.
Disposal
• Recycle or dispose of batteries in accordance with the battery
manufacturer’s instructions and local/national disposal and recycling
regulations.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as a power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
WARNING: Avoid electric shock and fire hazard! Never
push objects through the openings in this product. Foreign objects
can cause electrical shorts that can result in electric shock or fire.
Service Warnings
Protect the Product from Lightning
Provide Ventilation and Select a Location
Protect the Product When Moving It
In addition to disconnecting the AC power from the wall outlet, disconnect
the signal inputs.
• Remove all packaging material before applying power to the product.
Always disconnect the power source when moving the apparatus or
connecting or disconnecting cables.
Verify the Power Source from the On/Off Power
Light
• Do not place this apparatus on an unstable surface.
When the on/off power light is not illuminated, the apparatus may still be
connected to the power source. The light may go out when the apparatus
is turned off, regardless of whether it is still plugged into an AC power
source.
WARNING: Avoid electric shock and fire hazard! Do not
overload AC mains, outlets, extension cords, or integral convenience
receptacles. For products that require battery power or other power
sources to operate them, refer to the operating instructions for
those products.
• Do not place this apparatus on a bed, sofa, rug, or similar surface.
• Do not install this apparatus in an enclosure, such as a bookcase or rack,
unless the installation provides proper ventilation.
• Do not place entertainment devices (such as VCRs or DVDs), lamps,
books, vases with liquids, or other objects on top of this product.
• Do not block ventilation openings.
Protect from Exposure to Moisture and Foreign
Objects
WARNING: Avoid electric shock and fire hazard! Do not
expose this product to dripping or splashing liquids, rain, or moisture.
Objects filled with liquids, such as vases, should not be placed on
this apparatus.
Upon completion of any service or repairs to this product, the service
technician must perform safety checks to determine that this product is in
proper operating condition.
Models: 8640HD, 8642HD, 8650HD, 8652HD
Manufactured by:
Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 770-236-1077
AVC VIDEO LICENSE
With respect to each AVC/H.264 product, we are obligated to provide the
following notice:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE
FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER TO (i)
ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”)
AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM.
Accordingly, please be advised that service providers, content providers, and
broadcasters are required to obtain a separate use license from MPEG LA
prior to any use of AVC/H.264 encoders and/or decoders.
Macrovision Copyright Notice
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Macrovision, and is
intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or disassembly is
prohibited.
20081112_Cable_Safety
United States FCC Compliance
This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against such interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy. If not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
Canada EMI Regulation
Disclaimer
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003
du Canada.
Cisco Systems, Inc. assumes no responsibility for errors or omissions that
may appear in this guide. We reserve the right to change this guide at any
time without notice.
20081121 FCC Standard
Service Provider Video Technology Group
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
678.277.1000
www.scientificatlanta.com
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
WARNING: Avoid electric shock and fire hazard! Unplug
this product before cleaning. Do not use a liquid cleaner or an
aerosol cleaner. Do not use a magnetic/static cleaning device (dust
remover) to clean this product.
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions: 1) the device may not cause harmful interference,
and 2) the device must accept any interference received, including
interference that may cause undesired operation.
Cisco Explorer 8640HD, 8642HD, 8650HD,
and 8652HD High-Definition DVR Set-Tops
Check Product Safety
T11518
The information shown in the FCC Declaration of Conformity paragraph
below is a requirement of the FCC and is intended to supply you with
information regarding the FCC approval of this device. The phone numbers
listed are for FCC-related questions only and not intended for questions
regarding the connection or operation for this device. Please contact your
service provider for any questions you may have regarding the operation or
installation of this device.
Declaration of Conformity
WARNING: Avoid electric shock! Do not open the cover
of this product. Opening or removing the cover may expose you to
dangerous voltages. If you open the cover, your warranty will be
void. This product contains no user-serviceable parts.
• The batteries may contain perchlorate, a known hazardous substance,
so special handling and disposal of this product might be necessary.
For more information about perchlorate and best management
practices for perchlorate-containing substance, see www.dtsc.ca.gov/
hazardouswaste/perchlorate
Eliminate AC Mains Overloads
WARNING: Avoid electric shock and fire hazard! If this product
connects to coaxial cable wiring, be sure the cable system is grounded
(earthed). Grounding provides some protection against voltage surges
and built-up static charges.
EXIT
• Do not attempt to recharge ‘disposable’ or ‘non-reusable’ batteries.
WARNING: Avoid electric shock and fire hazard! Do
not locate an outside antenna system in the vicinity of overhead
power lines or power circuits. Touching power lines or circuits
might be fatal.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid
injury from tip-over.
Ground the Product
INFO
Safety
12)
The AC inlet on the unit must remain accessible and operable at all times.
GUIDE
L AUDIO IN R
• Do not expose batteries to temperatures above 100°C (212°F).
A label on this product indicates the correct power source for this product.
Operate this product only from an electrical outlet with the voltage and
frequency indicated on the product label. If you are uncertain of the type of
power supply to your home or business, consult your service provider or
your local power company.
CH-
WARNING: There is danger of explosion if the battery is
mishandled or incorrectly replaced. Replace only with the same type
of battery. Do not disassemble it or attempt to recharge it outside
the system. Do not crush, puncture, dispose of in fire, short the
external contacts, or expose to water or other liquids. Dispose of
the battery in accordance with local regulations and instructions
from your service provider.
11) Only use attachments/accessories specified by the
manufacturer.
Power Source Warning
SELECT
• Consult the service provider or an experienced radio/television technician
for help.
Any changes or modifications not expressly approved by Cisco Systems,
Inc., could void the user’s authority to operate the equipment.
Cisco, Cisco Systems, the Cisco logo, the Cisco Systems logo, Scientific Atlanta, and Explorer are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates
in the United States and certain other countries.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Macrovision is a registered trademark of Macrovision Corp.
MoCA is a trademark of the Multimedia over Coax Alliance.
All other trademarks mentioned in this document are the property of their respective owners.
Product and service availability is subject to change without notice.
© 2009 Cisco Systems, Inc. All rights reserved.
January 2009
Printed in United States of America
Part Number 4026879 Rev B
Welcome
Front Panel
The Cisco® Explorer® HD High-Definition DVR Set-Tops (set-tops) receive
and deliver digital signals, and deliver high-definition programming in
exceptional picture and audio quality. Use the simple user interface
to access favorite channels and parental control services. Contact
your service provider for information about these and other available
services. Use the instructions in this guide to install the set-top and to
access your program services.
Connecting to an HDTV with HDMI Input
1. Unplug all electronic devices before connecting the set-top.
Explorer 8652HD
3. Connect the set-top to the coaxial cable coming in from the wall.
CH+
VOL-
4. Plug the TV into an AC power source.
VOL+
POWER
SELECT
5. Plug the set-top’s power cord into an AC power source.
CH-
GUIDE
The consumer support website provides news and information about
this product. For more information, please refer to:
INFO
EXIT
6. For the TV to receive the signal, press the appropriate button on the remote control to select the audio/video inputs to which you have
connected the set-top.
LIST
L AUDIO IN R
VIDEO IN
7. Press the POWER key on the remote control.
http://www.cisco.com/web/consumer/support/index.html
2
1
3
4
5
7 8 9 10 11
6
12
T13899
Safety First
Before using this set-top read the IMPORTANT SAFETY
INSTRUCTIONS section of this guide.
Avoid Screen Burn-In
Images such as letterbox bars or side bars, bright closed-captioning
backgrounds, station logos, or any other stationary images may cause the
TV screen to age unevenly and cause damage to your TV. Refer to the user
guide that came with your TV for more information about screen burn-in.
Automatic Software Updates
A message appears on the TV screen when the set-top is receiving
software updates. In addition, download information also appears on the
front panel of the set-top during these updates. Wait for the current time
to display on the front panel before continuing. When the time appears,
the update is complete.
2. Connect the set-top and TV to the HDMI input as shown in the diagram.
1 Power
2 VOL-, VOL+
3 USB 2.0
4
5
6
7
8
CH+, CHSelect
IR Sensor
Guide
Info
9 Exit
10 List
11 Display
12 Smart Card
Turns the set-top on and off
Safety and Performance Tip
Decreases and increases the volume
Connects to external USB equipment approved by your
Keep the top of the set-top free of all objects
service provider, software controlled
and electronic devices, including your TV.
Scrolls up and down through the channels
Accesses your on-screen selection
Receives the infrared signal from the remote control
Accesses on-screen services, such as the on-screen guide, video-on-demand, or pay-per-view
Displays a description of the selected program. This button is available from the on-screen menu
and while viewing a program
Exit menus, the on-screen menu, and program information
Displays the recorded list
Displays the selected channel number and time of day. The display shows the following:
• Power ( )
• MoCA™ Link ( )
• 480i / 480P
• 5.1
• Message (
)
• HDTV
• 720i / 720P
• Record (
)
• Auto
• 1080i / 1080P
Allows smart card access
8652HD
OUTPUT
STB SN: SABPQBQGD
VIDEO
Y
DIGITAL
AUDIO
CAUTION
OPTICAL
AUDIO
OUT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
eCM MAC: 001AC3F4F757
THIS DEVICE IS INTENDED TO BE ATTACHED
TO A RECEIVER THAT IS NOT USED TO
RECEIVE OVER-THE-AIR BROADCAST
SIGNALS. CONNECTION OF THIS DEVICE
IN ANY OTHER FASHION MAY CAUSE
HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS AND IS IN VIOLATION
OF THE FCC RULES, PART 15.
SCIENTIFIC-ATLANTA, INC.
IR
L
Pb
120 VAC
60Hz 4.2A
500W
L
STB RF MAC: 001AC3F$F756
CABLE OUT
R
Pr
R
USB 2.0
CABLE IN
WITH MoCA
eSATA
120V~
60Hz 80W
S-VIDEO
OUT
CATV CONVERTER
MADE IN MEXICO
1394
Cable
Input
AUDIO
CENTER
CHANNEL IN
Note: This illustration may vary from the actual product.
ON
Performance Tips
ETHERNET
LISTED 14H1
VIDEO PRODUCT
HDMI
OFF
AUDIO IN
DVI/HDCP
If the set-top does not perform as expected, the following tips may help.
S-VIDEO
Back Panel
R
L
No picture
ANT (75 )
• Verify that the power to your TV is turned on.
OUTPUT
STB SN: SABPQBQGD
VIDEO
Y
DIGITAL
AUDIO
MULTI-STREAM CABLE CARD
OPTICAL
AUDIO
OUT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
L/
MONO
AVIS: RISQUE DE CHOC ÉLECTRIQUE
eCM MAC: 001AC3F4F757
IR
THIS DEVICE IS INTENDED TO BE ATTACHED
TO A RECEIVER THAT IS NOT USED TO
RECEIVE OVER-THE-AIR BROADCAST
SIGNALS. CONNECTION OF THIS DEVICE
IN ANY OTHER FASHION MAY CAUSE
HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS AND IS IN VIOLATION
OF THE FCC RULES, PART 15.
• Verify that all cables are properly connected.
• The current channel may not be available in your service package.
Try selecting another channel to see if a picture appears.
SCIENTIFIC-ATLANTA, INC.
NE PAS OUVRIR
MCARD SN: PXCPRPSLV
L
Pb
MCARD MAC: 00 1BD73E17D9
L
VIDEO
Y
VIDEO
• If the set-top is plugged into a wall switch, verify the switch is in the
ON position. (Avoid plugging into an outlet that is controlled by a
wall switch.)
120 VAC
60Hz 4.2A
500W
STB RF MAC: 001AC3F$F756
AUDIO
PB
L
PR
AUDIO
Y
L/
MONO
PB
L
R
PR
AUDIO
ANT-1
OUT
CABLE OUT
R
Pr
R
R
USB 2.0
CABLE IN
eSATA
S-VIDEO
OUT
CATV CONVERTER
MADE IN MEXICO
R
120V~
60Hz 80W
1394
ETHERNET
R
HD 2
HD 2
LISTED 14H1
VIDEO PRODUCT
Back of HDTV
IN
IN
OUT
IN
ANT-2
T14046
No color
1
• Verify the current TV program is broadcast in color.
• Adjust the TV color controls.
• Verify the volume is turned up.
• Verify the mute function is not on.
7
• If your setup includes a VCR or stereo, verify that you have properly
connected them to the set-top.
3
4
5 6 7 8 9 10 11
12
13
14 15 16 17
T13900
Note: This illustration may vary from the actual product.
1
2
3
4
5
6
No sound
2
8
9
10
Cable In
Video Out
Audio Out
HDTV (YPbPr)
Audio Out
Digital Audio Out
Connects to a coaxial cable that delivers the signal from your service provider
Connects to the composite input on your TV
Connects to RCA cables that send analog audio signals (left and right) to the stereo inputs on a TV
Connects to the component input (YPbPr) on the HDTV
Connects to RCA cables that send analog audio signals (left and right) to the stereo inputs on a TV
Connects to an RCA cable that sends a digital audio signal to a surround-sound receiver or other digital audio
device input
S-Video Out
Connects to an S-Video cable that sends an S-Video signal to your TV or VCR. This signal is standard-definition,
but higher quality than other SDTV connections
IR Remote Input Available to be connected to an approved remote IR receiver (purchased separately)
Cable Out
Connects to a coaxial cable that sends analog audio and video signals to a TV or VCR
Optical Audio Out Connects to an optical cable that sends a digital audio signal to a surround-sound receiver or other digital audio
device input
11 HDMI
12 USB 2.0
13 eSATA
14
15
16
17
1394
Ethernet
AC Power Input
AC Outlet
Connects an HDMI™ cable to the HDMI input of an HDTV. HDMI supports both digital audio and video. May be
used to connect to a DVI interface using an HDMI-to-DVI adapter for video and separate audio connections. Any of
the following audio connections may be used: Audio Out (3 or 5); Digital Audio Out (6); or Optical Audio Out (10)
Connects to external USB equipment approved by your service provider, software controlled
Connects to an external Serial ATA (eSATA) hard disk drive for expanded drive space. A connected eSATA drive is
not an archival device. Ask your service provider for a list of approved hard drive models for use with the DVR
Connects to display devices that are equipped with a 1394 input
Connects to external Ethernet equipment approved by your service provider
Connects to the power cord to deliver power to the set-top
Connects to the AC power cord from another device, such as a TV
Note: This illustration may vary from the actual product.
WARNING: Electric shock hazard! Unplug
all electronic devices before connecting or
disconnecting any device cables to the set-top.
U.S. Patents
A patent notice is affixed to this product. In addition, the product may also be covered by one or more of the following patents:
4,498,169; 4,692,919; 4,748,667; 4,829,569; 4,866,770; 4,885,775; 4,888,799; 4,890,319; 4,922,456; 4,922,532; 4,924,498; 4,965,534; 4,991,011; 5,003,384; 5,012,510; 5,029,207; 5,045,816; 5,053,883; 5,054,071;
5,058,160; 5,142,575; 5,142,690; 5,146,526; 5,155,590; 5,214,390; 5,225,902; 5,225,925; 5,235,619; 5,237,610; 5,239,540; 5,241,610; 5,247,364; 5,255,086; 5,257,403; 5,267,071; 5,270,809; 5,271,041; 5,272,752;
5,282,028; 5,285,497; 5,287,351; 5,301,028; 5,309,514; 5,317,391; 5,319,709; 5,341,425; 5,347,388; 5,347,389; 5,357,276; 5,359,601; 5,361,156; 5,367,571; 5,379,141; 5,379,145; 5,381,481; 5,390,337; 5,400,401;
5,406,558; 5,418,782; 5,420,866; 5,420,923; 5,425,101; 5,428,404; 5,430,568; 5,434,610; 5,436,749; 5,438,370; 5,440,632; 5,442,472; 5,455,570; 5,457,701; 5,471,492; 5,477,199; 5,477,262; 5,477,282; 5,477,370;
5,481,389; 5,481,542; 5,485,221; 5,493,339; 5,497,187; 5,500,758; 5,502,499; 5,506,904; 5,519,780; 5,539,822; 5,550,825; 5,579,055; 5,579,057; 5,583,562; 5,592,551; 5,596,606; 5,600,378; 5,602,933; 5,640,388;
5,657,414; 5,675,575; 5,684,876; 5,715,515; 5,724,525; 5,734,822; 5,740,300; 5,742,677; 5,754,940; 5,757,416; 5,771,064; 5,774,859; 5,825,829; 5,826,167; 5,850,305; 5,854,703; 5,870,474; 5,892,607; 5,920,626;
5,923,755; 5,930,024; 5,930,515; 5,937,067; 5,963,352; 5,966,163; 5,982,424; 5,991,139; 5,999,207; 6,005,631; 6,005,938; 6,016,163; 6,028,941; 6,029,046; 6,052,384; 6,055,244; 6,072,532; 6,105,134; 6,148,039;
6,157,719; 6,188,729; 6,195,389; 6,212,278; 6,215,530; 6,219,358; 6,240,103; 6,243,145; 6,246,767; 6,252,964; 6,272,226; 6,292,081; 6,292,568; 6,320,131; 6,374,275; 6,405,239; 6,411,602; 6,417,949; 6,424,714;
6,424,717; 6,433,906; 6,438,139; 6,463,586; 6,467,091; 6,476,878; 6,493,876; 6,510,519; 6,516,002; 6,516,412; 6,526,508; 6,538,595; 6,546,013; 6,560,340; 6,567,118; 6,570,888; 6,622,308; 6,629,227; 6,664,984;
6,667,994; 6,671,879; 6,674,967; 6,678,891; 6,714,598; 6,721,352; 6,721,956; 6,725,459; 6,738,982; 6,744,892; 6,744,967; 6,751,271; 6,760,918; 6,795,972; 6,802,077; 6,804,708; 6,811,447; 6,817,028; 6,822,972;
6,823,385; 6,832,386; 6,845,106; 6,868,473; 6,874,075; 6,889,191; 6,909,471; 6,917,622; 6,917,628; 6,922,412; 6,927,806; 6,928,656; 6,931,058; 6,937,729; 6,969,279; 6,971,008; 6,971,121; 6,978,310; 6,986,156;
6,988,900; 6,996,838; 7,010,801; 7,053,960; 7,065,213; 7,069,578; 7,069572; D348065; D354959; D359737; D363932; D390217; D434753; D507240; D507535; D513407; D516518; RE36368; RE36988
20070417 Patents