Delfield 4400 series Specifications

Installation &
Operation Manual
4400 Series
Compact Refrigerators
4500 Series
Compact Freezers
Please read this manual
completely before
attempting to install or
operate this equipment!
Notify carrier of damage.
Inspect all components
immediately.
Delfield 980 S. Isabella Rd., Mt. Pleasant, MI 48858
(989) 773-7891 or (800) 733-8829 • Fax (989) 773-3210
www.delfield.com
September 2010
Delfield
Contents
INTRODUCTION..............................................................................2
RECEIVING AND INSPECTING THE EQUIPMENT............................2
SPECIFICATIONS.........................................................................3-8
INSTALLATION...........................................................................9-10
Location..................................................................................9
Inside Cabinet.........................................................................9
Outside Cabinet.......................................................................9
Leveling..................................................................................9
Stabilizing...............................................................................9
Plumbing................................................................................9
Electrical Connection..........................................................9-10
REFRIGERATION Temperature Control................................11
Freezer temperature control............................................12
MAINTENANCE.............................................................................13
Care and Cleaning.................................................................13
BASIC MAINTENANCE..................................................................14
Gasket...................................................................................14
Doors/Hinges........................................................................14
Drain.....................................................................................14
Refrigeration Cycle................................................................14
Drawer Maintenance.............................................................14
Wiring Diagram................................................................15-16
Introduction
All cabinets have stainless steel exteriors and ABS interiors.
Door gaskets are magnetic and mount to the door, snapping
in place and are removable without tools.
Serial Number Location
The serial tag is located either on the left upper sidewall
inside the cabinet or under the top nosing directly above
the door when the door is in the closed position (right hand
door when there are two doors).
Always have the serial number of your cabinet available
when calling for parts or service. A complete list of
authorized Delfield parts depots is available on our website
at www.delfield.com.
This manual covers standard cabinets only. If you have a
custom cabinet, consult the customer service department
at (800) 733-8829.
©2010 The Delfield Company. All rights reserved. Reproduction without written
permission is prohibited. “Delfield” is a registered trademark of The Delfield Company.
STANDARD LABOR GUIDELINES..................................................17
LIMITED LIFETIME WARRANTY...................................................18
STANDARD ONE YEAR WARRANTY.............................................19
Figure 1. Serial Number Location
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should be
taken during unloading so the equipment is not damaged while
being moved into the building.
6.
7.
1.
2.
3.
4.
5.
Visually inspect the exterior of the package an skid or
container. Any damage should be noted and reported to the
delivering carrier immediately.
If damaged, open and inspect the contents with the carrier.
In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment notify
the carrier. Notification should be made verbally as well as
in written form.
Request an inspection of the concealed equipment.
This should be done within 10 days from receipt of the
equipment.
Check the lower portion of the unit to be sure legs or casters
are not bent.
8.
9.
Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines are
secure and base is still intact.
Freight carriers can supply the necessary forms upon
request.
Retain all crating material until an inspection has been made
or waived.
Do not use forklift or pallet jack to move this equipment
once it is removed from the pallet. Doing so may cause
equipment damage and void warranty.
Uncrating the Equipment
First cut and remove the banding from around the crate. Remove
the front of the crate material, use of some tools will be required.
If the unit is on legs remove the top of the crate as well and lift
the unit off the skid. If the unit is on casters it can be "rolled" off
the skid.
Compact Refrigerators
SPECIFICATIONS
Undercounter Refrigerators
Model
Description
L
Overall
H
D
Volume
Shelves
1/6 Pan
FT3
FT2
Capacity
H.P.
Refg. Charge
Amp
(oz)
NEMA
Ship Weight
Plug
(lbs)
UC4427N
one door
27”
31.5”
34.25”
8.20
3.20
—
1/5
7.0
3.9
5-15P
220
UCD4427N
two drawer
27”
31.5”
34.25”
8.20
—
—
1/5
7.0
3.9
5-15P
265
UC4432N
one door
32”
31.5”
34.25”
10.10
3.88
—
1/5
7.0
3.9
5-15P
280
UCD4432N
two drawer
32”
31.5”
34.25”
10.10
—
—
1/5
7.0
3.9
5-15P
315
UC4448N
two door
48”
31.5”
34.25”
16.00
5.48
—
1/5
7.0
3.9
5-15P
335
UCD4448N
four drawer
48”
31.5”
34.25”
16.00
—
—
1/5
7.0
3.9
5-15P
370
UC4460N
two door
60”
31.5”
34.25”
20.20
7.19
—
1/5
7.0
3.9
5-15P
460
UCD4460N
four drawer
60”
31.5”
34.25”
20.20
—
—
1/5
7.0
3.9
5-15P
519
UC4464N
two door
64”
31.5”
34.25”
21.60
7.76
—
1/5
7.0
3.9
5-15P
395
UCD4464N
four drawer
64”
31.5”
34.25”
21.60
—
—
1/5
7.0
3.9
5-15P
440
UC4472N
three door
72”
31.5”
34.25”
24.80
8.22
—
1/5
7.0
3.9
5-15P
485
UCD4472N
six drawer
72”
31.5”
34.25”
24.80
—
—
1/5
7.0
3.9
5-15P
545
Volume
Shelves
1/6 Pan
H.P.
FT3
FT2
Capacity
3.20
—
1/5
7.0
Flat Top & Work Top Refrigerator Bases
Model
Description
L
Overall D
H
Refg.
Amp
NEMA
Ship Weight
Plug
(lbs)
3.9
5-15P
220
Charge (oz)
4427N
one door
27”
31.5”
36”
8.20
D4427N
two drawer
27”
31.5”
36”
8.20
—
—
1/5
7.0
3.9
5-15P
265
ST4427N
one door
27”
31.5”
36”
8.20
3.20
—
1/5
7.0
3.9
5-15P
220
STD4427N
two drawer
27”
31.5”
36”
8.20
—
—
1/5
7.0
3.9
5-15P
265
4432N
one door
32”
31.5”
36”
10.10
3.88
—
1/5
7.0
3.9
5-15P
280
D4432N
two drawer
32”
31.5”
36”
10.10
—
—
1/5
7.0
3.9
5-15P
315
ST4432N
one door
32”
31.5”
36”
10.10
3.88
—
1/5
7.0
3.9
5-15P
280
STD4432N
two drawer
32”
31.5”
36”
10.10
—
—
1/5
7.0
3.9
5-15P
315
4448N
two door
48”
31.5”
36”
16.00
5.48
—
1/5
7.0
3.9
5-15P
335
D4448N
four drawer
48”
31.5”
36”
16.00
—
—
1/5
7.0
3.9
5-15P
370
ST4448N
two door
48”
31.5”
36”
16.00
5.48
—
1/5
7.0
3.9
5-15P
335
STD4448N
four drawer
48”
31.5”
36”
16.00
—
—
1/5
7.0
3.9
5-15P
370
4460N
two door
60”
31.5”
36”
20.20
7.19
—
1/5
7.0
3.9
5-15P
460
D4460N
four drawer
60”
31.5”
36”
20.20
—
—
1/5
7.0
3.9
5-15P
519
ST4460N
two door
60”
31.5”
36”
20.20
7.19
—
1/5
7.0
3.9
5-15P
460
STD4460N
four drawer
60”
31.5”
36”
20.20
—
—
1/5
7.0
3.9
5-15P
519
4464N
two door
64”
31.5”
36”
21.60
7.76
—
1/5
7.0
3.9
5-15P
395
D4464N
four drawer
64”
31.5”
36”
21.60
—
—
1/5
7.0
3.9
5-15P
440
ST4464N
two door
64”
31.5”
36”
21.60
7.76
—
1/5
7.0
3.9
5-15P
395
STD4464N
four drawer
64”
31.5”
36”
21.60
—
—
1/5
7.0
3.9
5-15P
440
4472N
three door
72”
31.5”
36”
24.80
8.22
—
1/5
7.0
3.9
5-15P
485
D4472N
six drawer
72”
31.5”
36”
24.80
—
—
1/5
7.0
3.9
5-15P
545
ST4472N
three door
72”
31.5”
40”
24.80
8.22
—
1/5
7.0
3.9
5-15P
485
STD4472N
six drawer
72”
31.5”
40”
24.80
—
—
1/5
7.0
3.9
5-15P
545
ST prefix models have a 4" stainless steel backsplash.
Delfield
Salad Top Refrigerator Bases
Model
Description
L
Overall
H
Volume FT3 Shelves
D
1/6 Pan
FT2
Capacity
3.24
6
H.P.
Refg. Charge
Amp
(oz)
NEMA
Ship Weight
Plug
(lbs)
5-15P
240
4427N-6
one door
D4427N-6
two drawer
27”
31.5”
36”
8.20
—
6
1/5
9
7.2
5-15P
290
4448N-8
two door
48”
31.5”
36”
16.00
5.48
8
1/5
9
7.2
5-15P
320
D4448N-8
four drawer
48”
31.5”
36”
16.00
—
8
1/5
9
7.2
5-15P
395
4448N-12
two door
48”
31.5”
36”
16.00
5.48
12
1/5
9
7.2
5-15P
320
D4448N-12
four drawers
48”
31.5”
36”
16.00
—
12
1/5
9
7.2
5-15P
395
ST4448N-8
two door
48”
31.5”
36”
16.00
5.48
8
1/5
9
7.2
5-15P
320
STD4448N-8
four drawers
48”
31.5”
36”
16.00
—
8
1/5
9
7.2
5-15P
395
4460N-8
two door
60”
31.5”
36”
20.20
7.19
8
1/2
12
12
5-15P
345
D4460N-8
four drawer
60”
31.5”
36”
20.20
—
8
1/2
12
12
5-15P
450
4460N-12
two door
60”
31.5”
36”
20.20
7.19
12
1/2
12
12
5-15P
345
D4460N-12
four drawer
60”
31.5”
36”
20.20
—
12
1/2
12
12
5-15P
450
ST4460N-8
two door
60”
31.5”
36”
20.20
7.19
8
1/2
12
12
5-15P
345
STD4460N-8
four drawer
60”
31.5”
36”
20.20
—
8
1/2
12
12
5-15P
450
4464N-8
two door
64”
31.5”
36”
21.60
7.76
8
1/2
12
12
5-15P
446
D4464N-8
four drawer
64”
31.5”
36”
21.60
—
8
1/2
12
12
5-15P
456
4464N-12
two door
64”
31.5”
36”
21.60
7.76
12
1/2
12
12
5-15P
446
D4464N-12
four drawer
64”
31.5”
36”
21.60
—
12
1/2
12
12
5-15P
456
446
27”
31.5”
36”
8.20
1/5
9
7.2
4464N-16
two door
64”
31.5”
36”
21.60
7.76
16
1/2
12
12
5-15P
D4464N-16
four drawer
64”
31.5”
36”
21.60
—
16
1/2
12
12
5-15P
456
ST4464N-8
two door
64”
31.5”
36”
21.60
7.76
8
1/2
12
12
5-15P
446
STD4464N-8
four drawer
64”
31.5”
36”
21.60
—
8
1/2
12
12
5-15P
456
ST4464N-12
two door
64”
31.5”
36”
21.60
7.76
12
1/2
12
12
5-15P
446
456
STD4464N-12
four drawer
64”
31.5”
36”
21.60
—
12
1/2
12
12
5-15P
4472N-12
three door
72”
31.5”
36”
24.80
8.22
12
1/2
12
12
5-15P
485
D4472N-12
six drawer
72”
31.5”
36”
24.80
—
12
1/2
12
12
5-15P
545
4472N-18
three door
72”
31.5”
36”
24.80
8.22
18
1/2
12
12
5-15P
485
D4472N-18
six drawer
72”
31.5”
36”
24.80
—
18
1/2
12
12
5-15P
545
ST4472N-12
three door
72”
31.5”
36”
24.80
8.22
12
1/2
12
12
5-15P
485
STD4472N-12
six drawer
72”
31.5”
36”
24.80
—
12
1/2
12
12
5-15P
545
ST prefix models have a 4" stainless steel backsplash.
Compact Refrigerators
Mega Top Refrigerated Front Breathers
Model
Description
L
Overall
H
D
Volume
Shelves
1/6 Pan
FT3
FT2
Capacity
H.P.
Refg. Charge
Amp
(oz)
NEMA
Ship Weight
Plug
(lbs)
4427N-9M
one door
27”
31.5”
36”
8.20
3.24
9
1/5
9
7.2
5-15P
290
D4427N-9M
two drawer
27”
31.5”
36”
8.20
—
9
1/5
9
7.2
5-15P
325
4427N-12M
one door
27”
31.5”
36”
8.20
3.24
12
1/5
9
7.2
5-15P
290
D4427N-12M
two drawer
27”
31.5”
36”
8.20
—
12
1/5
9
7.2
5-15P
325
4432N-12M
one door
32”
31.5”
36”
10.10
3.88
12
1/5
9
7.2
5-15P
315
D4432N-12M
two drawer
32”
31.5”
36”
10.10
—
12
1/5
9
7.2
5-15P
350
4448N-18M
two door
48”
31.5”
36”
16.00
5.48
18
1/5
9
7.2
5-15P
360
D4448N-18M
four drawer
48”
31.5”
36”
16.00
—
18
1/5
9
7.2
5-15P
395
4460N-12M
two door
60”
31.5”
36”
20.20
7.19
12
1/2
12
12
5-15P
430
D4460N-12M
four drawer
60”
31.5”
36”
20.20
—
12
1/2
12
12
5-15P
465
4460N-18M
two door
60”
31.5”
36”
20.20
7.19
18
1/2
12
12
5-15P
430
D4460N-18M
four drawer
60”
31.5”
36”
20.20
—
18
1/2
12
12
5-15P
465
4460N-24M
two door
60”
31.5”
36”
20.20
7.19
24
1/2
12
12
5-15P
430
D4460N-24M
four drawer
60”
31.5”
36”
20.20
—
24
1/2
12
12
5-15P
465
ST4460N-12M
two door
60”
31.5”
36”
20.20
7.19
12
1/2
12
12
5-15P
430
STD4460N-12M
four drawer
60”
31.5”
36”
20.20
—
12
1/2
12
12
5-15P
465
ST4460N-18M
two door
60”
31.5”
36”
20.20
7.19
18
1/2
12
12
5-15P
430
STD4460N-18M
four drawer
60”
31.5”
36”
20.20
—
18
1/2
12
12
5-15P
465
4464N-12M
two door
64”
31.5”
36”
21.60
7.76
12
1/2
12
12
5-15P
435
D4464N-12M
four drawer
64”
31.5”
36”
21.60
—
12
1/2
12
12
5-15P
470
4464N-18M
two door
64”
31.5”
36”
21.60
7.76
18
1/2
12
12
5-15P
435
D4464N-18M
four drawer
64”
31.5”
36”
21.60
—
18
1/2
12
12
5-15P
470
4464N-24M
two door
64”
31.5”
36”
21.60
7.76
24
1/2
12
12
5-15P
435
D4464N-24M
four drawer
64”
31.5”
36”
21.60
—
24
1/2
12
12
5-15P
470
ST4464N-12M
two door
64”
31.5”
36”
21.60
7.76
12
1/2
12
12
5-15P
435
STD4464N-12M
four drawer
64”
31.5”
36”
21.60
—
12
1/2
12
12
5-15P
470
ST4464N-18M
two door
64”
31.5”
36”
21.60
7.76
18
1/2
12
12
5-15P
435
STD4464N-18M
four drawer
64”
31.5”
36”
21.60
—
18
1/2
12
12
5-15P
470
4472N-18M
three door
72”
31.5”
36”
24.80
8.22
18
1/2
12
12
5-15P
485
D4472N-18M
six drawer
72”
31.5”
36”
24.80
—
18
1/2
12
12
5-15P
545
4472N-24M
three door
72”
31.5”
36”
24.80
8.22
24
1/2
12
12
5-15P
485
D4472N-24M
six drawer
72”
31.5”
36”
24.80
—
24
1/2
12
12
5-15P
545
4472N-30M
three door
72”
31.5”
36”
24.80
8.22
30
1/2
12
12
5-15P
485
D4472N-30M
six drawer
72”
31.5”
36”
24.80
—
30
1/2
12
12
5-15P
545
ST4472N-18M
three door
72”
31.5”
36”
24.80
8.22
18
1/2
12
12
5-15P
485
STD4472N-18M
six drawer
72”
31.5”
36”
24.80
—
18
1/2
12
12
5-15P
545
ST4472N-24M
three door
72”
31.5”
36”
24.80
8.22
24
1/2
12
12
5-15P
485
STD4472N-24M
six drawer
72”
31.5”
36”
24.80
—
24
1/2
12
12
5-15P
545
ST prefix models have a 4" stainless steel backsplash.
Delfield
Reduced Work Height Salad Top Refrigerated Front Breathers
Model
Description
L
Overall
H
D
Volume
Shelves
1/6 Pan
FT3
FT2
Capacity
H.P.
Refg. Charge
Amp
(oz)
NEMA
Ship Weight
Plug
(lbs)
UC4427N-6
one door
27”
31.5”
34.25”
8.20
3.24
6
1/5
9
7.2
5-15P
240
UCD4427N-6
two drawer
27”
31.5”
34.25”
8.20
—
6
1/5
9
7.2
5-15P
290
UC4448N-8
two door
48”
31.5”
34.25”
16.00
5.48
8
1/5
9
7.2
5-15P
320
UCD4448N-8
four drawer
48”
31.5”
34.25”
16.00
—
8
1/5
9
7.2
5-15P
395
UC4448N-12
two door
48”
31.5”
34.25”
16.00
5.48
12
1/5
9
7.2
5-15P
320
UCD4448N-12
four drawer
48”
31.5”
34.25”
16.00
—
12
1/5
9
7.2
5-15P
395
UC4460N-8
two door
60”
31.5”
34.25”
20.20
7.19
8
1/2
12
12
5-15P
345
UCD4460N-8
four drawer
60”
31.5”
34.25”
20.20
—
8
1/2
12
12
5-15P
450
UC4460N-12
two door
60”
31.5”
34.25”
20.20
7.19
12
1/2
12
12
5-15P
345
UCD4460N-12
four drawer
60”
31.5”
34.25”
20.20
—
12
1/2
12
12
5-15P
450
UC4464N-8
two door
64”
31.5”
34.25”
21.60
7.76
8
1/2
12
12
5-15P
446
UCD4464N-8
four drawer
64”
31.5”
34.25”
21.60
—
8
1/2
12
12
5-15P
456
UC4464N-12
two door
64”
31.5”
34.25”
21.60
7.76
12
1/2
12
12
5-15P
446
UCD4464N-12
four drawer
64”
31.5”
34.25”
21.60
—
12
1/2
12
12
5-15P
456
UC4464N-16
two door
64”
31.5”
34.25”
21.60
7.76
16
1/2
12
12
5-15P
446
UCD4464N-16
four drawer
64”
31.5”
34.25”
21.60
—
16
1/2
12
12
5-15P
456
UC4472N-12
three door
72”
31.5”
34.25”
24.80
8.22
12
1/2
12
12
5-15P
485
UCD4472N-12
six drawer
72”
31.5”
34.25”
24.80
—
12
1/2
12
12
5-15P
545
UC4472N-18
three door
72”
31.5”
34.25”
24.80
8.22
18
1/2
12
12
5-15P
485
UCD4472N-18
six drawer
72”
31.5”
34.25”
24.80
—
18
1/2
12
12
5-15P
545
Compact Refrigerators
Reduced Work Height Mega Top Refrigerated Front Breathers
Model
Description
L
Overall
H
D
Volume
Shelves
1/6 Pan
FT3
FT2
Capacity
H.P.
Refg. Charge
3.24
9
1/5
9
Amp
NEMA
Ship Weight
Plug
(lbs)
7.2
5-15P
290
(oz)
UC4427N-9M
one door
27”
31.5”
34.25”
8.20
UCD4427N-9M
two drawer
27”
31.5”
34.25”
8.20
—
9
1/5
9
7.2
5-15P
325
UC4427N-12M
one door
27”
31.5”
34.25”
8.20
3.24
12
1/5
9
7.2
5-15P
290
UCD4427N-12M
two drawer
27”
31.5”
34.25”
8.20
—
12
1/5
9
7.2
5-15P
325
UC4432N-12M
one door
32”
31.5”
34.25”
10.10
3.88
12
1/5
9
7.2
5-15P
315
UCD4432N-12M
two drawer
32”
31.5”
34.25”
10.10
—
12
1/5
9
7.2
5-15P
350
UC4448N-18M
one door
48”
31.5”
34.25”
16.00
5.48
18
1/5
9
7.2
5-15P
360
UCD4448N-18M
two drawer
48”
31.5”
34.25”
16.00
—
18
1/5
9
7.2
5-15P
395
UC4460N-12M
two door
60”
31.5”
34.25”
20.20
7.19
12
1/2
12
12
5-15P
430
UCD4460N-12M
four drawer
60”
31.5”
34.25”
20.20
—
12
1/2
12
12
5-15P
465
UC4460N-18M
two door
60”
31.5”
34.25”
20.20
7.19
18
1/2
12
12
5-15P
430
UCD4460N-18M
four drawer
60”
31.5”
34.25”
20.20
—
18
1/2
12
12
5-15P
465
UC4460N-24M
two door
60”
31.5”
34.25”
20.20
7.19
24
1/2
12
12
5-15P
430
UCD4460N-24M
four drawer
60”
31.5”
34.25”
20.20
—
24
1/2
12
12
5-15P
465
UC4464N-12M
two door
64”
31.5”
34.25”
21.60
7.76
12
1/2
12
12
5-15P
435
UCD4464N-12M
four drawer
64”
31.5”
34.25”
21.60
—
12
1/2
12
12
5-15P
470
UC4464N-18M
two door
64”
31.5”
34.25”
21.60
7.76
18
1/2
12
12
5-15P
435
UCD4464N-18M
four drawer
64”
31.5”
34.25”
21.60
—
18
1/2
12
12
5-15P
470
UC4464N-24M
two door
64”
31.5”
34.25”
21.60
7.76
24
1/2
12
12
5-15P
435
UCD4464N-24M
four drawer
64”
31.5”
34.25”
21.60
—
24
1/2
12
12
5-15P
470
UC4472N-18M
three door
72”
31.5”
34.25”
24.80
8.22
18
1/2
12
12
5-15P
485
UCD4472N-18M
six drawer
72”
31.5”
34.25”
24.80
—
18
1/2
12
12
5-15P
545
UC4472N-24M
three door
72”
31.5”
34.25”
24.80
8.22
24
1/2
12
12
5-15P
485
UCD4472N-24M
six drawer
72”
31.5”
34.25”
24.80
—
24
1/2
12
12
5-15P
545
UC4472N-30M
three door
72”
31.5”
34.25”
24.80
8.22
30
1/2
12
12
5-15P
485
UCD4472N-30M
six drawer
72”
31.5”
34.25”
24.80
—
30
1/2
12
12
5-15P
545
Delfield
FREEZER SPECIFICATIONS
Flat top freezer bases
Model
Description
L
D
H
Volume
Ft.3
Shelves
Ft.2
H.P.
Refg. Charge
(oz)
Amp
NEMA
Plug
Ship
Weight
(lbs)
4532N
one door
32”
(81.3cm)
31.5”
(80.0cm)
36”
(91.4cm)
8.80
3.88
1/5
9.0
9.5
5-15P
280lbs
(127kg)
D4532N
two drawer
32”
(81.3cm)
31.5”
(80.0cm)
36”
(91.4cm)
8.80
—
1/3
9.5
9.5
5-15P
315lbs
(143kg)
ST4532N
one door
32”
(81.3cm)
31.5”
(80.0cm)
36”
(91.4cm)
8.80
3.88
1/5
9.0
9.5
5-15P
280lbs
(127kg)
STD4532N
two drawer
32”
(81.3cm)
31.5”
(80.0cm)
36”
(91.4cm)
8.80
—
1/3
9.5
9.5
5-15P
315lbs
(143kg)
4560N
two door
60”
(152.4cm)
31.5”
(80.0cm)
36”
(91.4cm)
16.90
7.19
1/3
14.0
12.0
5-15P
474lbs
(215kg)
ST4560N
two door
60”
(152.4cm)
31.5”
(80.0cm)
36”
(91.4cm)
16.90
7.19
1/3
14.0
12.0
5-15P
479lbs
(217kg)
L
D
H
Volume
Ft.3
Shelves
Ft.2
H.P.
Refg. Charge
Amp
NEMA
Plug
Ship
Weight
ST prefix models have a 4" stainless steel backsplash.
Undercounter freezers
Model
Description
UC4532N
one door
32”
(81.3cm)
31.5”
(80.0cm)
34.25”
(87.0cm)
8.80
3.88
1/5
9.0
9.5
5-15P
280lbs
(127kg)
UCD4532N
two drawer
32”
(81.3cm)
31.5”
(80.0cm)
34.25”
(87.0cm)
8.80
—
1/3
9.5
9.5
5-15P
315lbs
(143kg)
UC4560N
two door
60”
(152.4cm)
31.5”
(80.0cm)
34.25”
(87.0cm)
16.90
7.19
1/3
14.0
12.0
5-15P
474lbs
(215kg)
Compact Refrigerators
INSTALLATION
Stabilizing
Location
All models are supplied standard on casters for your
convenience, for ease of cleaning underneath and for
mobility.
Cabinets represented in this manual are intended for
indoor use only. Be sure the location chosen has a floor
strong enough to support the total weight of the cabinet
and contents. Reinforce the floor as necessary to provide
for maximum loading.
The location should be selected so that power cords can
be connected without any extensions.
For the most efficient operation, be sure to provide good
air circulation inside and outside the cabinet. Avoid hot
corners and locations near stoves and ovens.
Inside Cabinet
Do not pack refrigerator so full that air cannot
circulate.
Outside Cabinet
4400 Series equipment door and drawer models
These cabinets have Delfield’s “front-breathing” design.
They may be installed flush against a wall or built into a
counter as required.
The louver at the floor level must be kept completely clear
of any obstructions. Proper operation of these models
is dependent on air being able to flow freely through
the front louver. The louver at the back of the cabinet
is not necessary for proper operation, but any air flow
through it is beneficial.
CAUTION
Any restriction of the proper air flow outlined above,
total or partial, will void the warranty on the cabinet.
Leveling
A level cabinet will perform better because the drain
pan will drain properly, the drawers or doors will line
up with the frames and the cabinet will not be subject
to undue strain.
CAUTION
Never stand on the unit or its drawers! Doing so may
result in bodily injury. They are not designed to hold
the weight of a person and will collapse if misused in
this manner.
CAUTION
The cabinet must be installed in a stable condition
with the front wheels locked. Locking the front
casters after installation is the owner’s and operator’s
responsibility.
Plumbing
Self-contained models are standard with a condensate
evaporator. If, for some reason, a cabinet does not have
a condensate evaporator, or the evaporator fails, the
cabinets drain must have an outlet to an appropriate
drainage area or container.
CAUTION
Moisture collecting from improper drainage can create a
slippery surface on the floor and a hazard to employees.
It is the owner’s and operator’s responsibility to provide
a container or outlet for drainage.
Electrical Connection
CAUTION
A 7’ (2.1 m) long grounded supply cord and threepronged plug are provided with standard cabinets.
Simply plug into a three-pronged wall outlet for proper
grounding of the cabinet to begin operation. Do not
use an adapter to connect to a two-pronged outlet. The
three-pronged outlet provides a ground connection
which must be used to prevent a shock hazard.
CAUTION
The wall outlet must be checked by a qualified electrician
to be sure a proper ground is present and that the outlet
provides the correct voltage and required amperage to
match the rating plate.
Any power cord that is frayed or damaged should be
replaced. When disconnecting the cabinet from the power
source, do not pull on the cord. Firmly grip the plug and
remove from outlet.
Delfield
The 15-P plug shown in Figure 2 is used on the various
4400 Series models.
Figure 2. 5-15P Connector
Refer to the amperage data list in SPECIFICATIONS, the
serial tag, your local code or the National Electrical Code
to be sure the cabinet is connected to the proper power
source. A protected circuit of the correct voltage and
amperage must be run for connection of the line cord,
or permanent connection to the cabinet.
CAUTION
The thermostat must be turned to OFF and the cabinet
disconnected from the power source whenever
performing service, maintenance functions or cleaning
the refrigerated area.
10
Compact Refrigerators
OPERATION
Refrigerated Cabinets
After the cabinet is connected to the power source it will
automatically begin operating. With the covers and doors
closed, the temperature of the cabinet should reach 36°F
to 40°F (2°C to 4°C) in about one hour. Temperature on
salad top will maintain 33°F to 41°F (1°C to 4°C) with pans
recessed 2.5” (6.5cm) at 86°F ambient room temperature
for a period of four hours, meeting NSF-7 requirements.
The temperature control on a flat top unit is located on
the back panel inside the refrigerator and can be adjusted
to meet the current conditions. The temperature control
on a salad top unit is located in the rear of the unit, 14"
to 16" above floor in access hole.
Units
A thermostat located in rear of cabinet controls the
temperature inside the box (see Figure 5). The factory
setting for the control is 5 and maintains about
34°F(1°C) to 36°F (2°C) inside the box. Set toward
1 for higher temperatures and toward 9 for lower
temperatures.
CAUTION
Refrigerated cabinets with two evaporators have counterrotating fans to ensure even airflow throughout the
cabinet. The left evaporator has a CCW motor and a clear
fan blade and right evaporator has a CW motor and a
black fan blade.
Temperature Control Instruction for Flat Top Units
A thermostat located in the evaporator housing on the
interior rear of the cabinet controls the temperature
inside the box (see Figure 4). The factory setting for the
control is “4” and maintains about 38°F (3°C) inside the
box. Set toward “1” for higher temperatures and toward
“7” for lower temperatures.
Temperature Control Instruction for Salad Top
Figure 5. Thermostat Location - Salad Top
Cabinets with pans should be operated with pans in
place. Operating the cabinet without all pans in place
will lessen efficiency and may damage the cabinet.
Continuous opening and closing of the door will hamper
the cabinet’s ability to maintain optimum refrigeration
temperature.
Top section is not intended for overnight storage. Product
should be removed from pans. Pans can remain in cabinet
while empty.
Defrosting
Refrigerators defrost automatically with every cycle of
the compressor. The water generated is routed to a pan
on the rear of the cabinet and is evaporated by the heat
given off by the compressor.
Figure 4. Thermostat Location - Flat Top
11
Delfield
OPERATION
freEZeR Cabinets
The electronic temperature control constantly monitors box
temperature as well as evaporator coil temperature to maintain
consistent product temperatures.
At initial start-up or anytime power is disconnected, then
reconnected to the unit, the control will delay all operations for
a short time (up to 10 minutes.) While in this delay period, the
control initializes the control parameters and confirms that the
temperature sensors and circuits are operational.
amount of frost accumulated on the evaporator coil.
After the defrost cycle is complete, the control returns to a normal
refrigeration cycle, however the evaporator fan motor will not
switch on for 2 minutes AFTER the compressor and condenser
fan motor have begun operating.
Freezer Manual Defrost
If a manual defrost is desired, simply unplug the unit for several
seconds, then plug unit back in. This will cause the control to
re-initialize and then enter a defrost cycle.
REGARDING FREEZERS: After initializing, the
control will immediately enter a DEFROST mode.
The compressor and condenser fan as well as the
evaporator fan will remain off until initialization
defrost is complete. This initial defrost cycle may
take up to 15 minutes to complete, at which time
the freezing cycle will begin.
The control is located in the rear of the cabinet (See Figure 6.).
Freezers are factory set at mid-range to maintain about -3ºF
(-19ºC) box temperature. To adjust for colder temperatures,
turn the knob clockwise. For warmer temperatures, turn the
knob counter-clockwise. Turn the knob fully counter-clockwise
to turn the refrigeration system off. Never turn the knob more
than 1 dial number and always allow 8 hours for temperature
stabilization before making any additional adjustments.
Freezer cabinets with two evaporators have counter-rotating fans
to ensure even airflow throughout the cabinet. The left evaporator
has a CCW motor and a clear fan blade and the right evaporator
has a CW motor and a black fan blade.
The evaporator fan(s) and condenser fan will cycle off and on
with the compressor to conserve energy.
Freezer:
Whenever the freezer is plugged in, and the control has completed
initializing including the initial defrost cycle. The temperature
control will cycle the compressor and condenser fan motor
and evaporator fan motor to maintain box temperature at the
control setting.
Freezer Automatic Defrost
The control also monitors compressor total running time and
will enter a defrost cycle after total compressor running time is
greater than 4-hours since the last defrost cycle OR if evaporator
coil temperature drops below -34ºF (-37ºC) (indicating excessive
frost on the coil.)
When the control enters the defrost mode, it switches off the
evaporator fan motor, compressor and condenser fan motor, and
switches on the defrost heater to warm the evaporator coil. Thereby
melting all frost accumulated during the previous refrigeration
cycle. The control will continue the defrost cycle for a MINIMUM
of 8 minutes and a MAXIMUM of 30 minutes depending on the
12
Figure 6. Thermostat Location - Freezer
Compact Refrigerators
MAINTENANCE
CAUTION
CAUTION
The thermostat must be turned to OFF and the cabinet
disconnected from the power source whenever
performing service, maintenance functions or cleaning
the refrigerated area.
STAINLESS STEEL CARE AND
CLEANING
To prevent discoloration or rust on stainless steel several
important steps need to be taken. First, the properties
of stainless steel need to be understood. Stainless steel
contains 70-80% iron which will rust. It also contains
12-30% chromium which forms an invisible passive film
over the steels surface which acts as a shield against
corrosion. As long as the protective layer is intact, the
metal will not corrode and is still stainless. If the film is
broken or contaminated, outside elements can begin
to breakdown the steel and begin to form rust or other
discoloration.
CAUTION
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Do not use an abrasive cleaner because it will scratch
the stainless steel and plastic and can damage gaskets.
Proper cleaning of stainless steel requires soft cloths or
plastic scouring pads.
Cleaning solutions need to be alkaline based or nonchloride cleaners. Any cleaner containing chlorides
will damage the protective film of the stainless steel.
Chlorides are also commonly found in hard water,
salts and household and industrial cleaners. If cleaners
containing chlorides are used, be sure to rinse repeatedly
and dry thoroughly upon completion.
Routine cleaning of the interior and exterior can be done
with soap and warm water. Extreme stains or grease
should be cleaned with a non-abrasive cleaner and
plastic scrub pad. When cleaning the exterior, always rub
with the grain of the stainless steel to avoid marring the
finish. There are also stainless steel cleaners available
which can restore and preserve the finish of the steels
protective layer.
Early signs of stainless steel breakdown can consist of
small pits and cracks. If this has begun, clean thoroughly
and start to apply stainless steel cleaners in an attempt
to restore the passivity of the steel.
Never use an acid based cleaning solution! Many food
products have an acidic content which can deteriorate
the finish. Be sure to clean ALL food products from
any stainless steel surface. Common items include,
tomatoes, peppers and other vegetables.
CLEANING THE CONDENSER COIL
The condenser coil requires regular cleaning every 90
days (recommended). In some instances you may find a
large amount of debris and dust or grease accumulated
prior to the 90 day time frame. In these cases the
condenser coil should be cleaned every 30 days.
If the build up on the coil consists of only light dust and
debris the condenser coil can be cleaned with a simple
brush. Heavier dust build up may require a vacuum or
even compressed air to blow through the condenser
coil.
If heavy grease is present there are de-greasing agents
available for refrigeration use, and specifically for the
condenser coils. The condenser coil may require using
a de-greasing agent and then being blown through
with compressed air. Follow the de-greasing agent
manufacturer’s instructions.
Failure to maintain a clean condenser coil can initially
cause high temperatures and excessive run times.
Continuous operation with dirty or clogged condenser
coils can result in compressor failure. Neglecting the
condenser coil cleaning procedures will void any
warranties associated with the compressor or cost to
replace the compressor.
CAUTION
Never use a high pressure water wash for this cleaning
procedure as water can damage the electrical
components located near or at the condenser coil.
In order to maintain proper refrigeration performance,
the condenser fins must be cleaned of dust, dirt and
grease regularly. It is recommended that this be done
every three months. If conditions are such that the
condenser is totally blocked in three months, the
frequency of cleaning should be increased. Clean the
condenser with a vacuum cleaner or stiff brush. If
extremely dirty, a commercially available condenser
cleaner may be required.
If your freezer seems to vibrate excessively when the
compressor is running, loosen (but do not remove) the
bolts on the compressor. Semi-hermetic models should
13
Delfield
be loosened before operating.
BASIC MAINTENANCE
Gasket Maintenance
Gaskets require regular cleaning to prevent mold and
mildew build up and also to maintain the elasticity of
the gasket. Gasket cleaning can be done with the use of
warm soapy water. Avoid full strength cleaning products
on gaskets as this can cause them to become brittle and
prevent proper seals. Also, never use sharp tools or knives
to scrape or clean the gasket which could possibly tear
the gasket and rip the bellows.
or bumping the drain. If you notice excessive water
accumulation on the inside of the cabinet, be sure the
drain tube is connected from the evaporator housing
to the condensate evaporator drain pan. If water has
collected underneath the cabinet, check the condensate
evaporator drain tube to be sure it is still located inside
the drain pan. Leveling the cabinet is important as it is
designed to drain properly when on a level surface. If
your floor is not level this can also cause drain problems.
Be sure all drain lines are free of obstructions. Typically,
food product is found blocking drain lines causing water
to back up and overflow the drain pans.
Drawer Maintenance
Gaskets can easily be replaced and do not require the
use of tools or authorized service persons. The gaskets
are “Dart” style and can be pulled out of the groove in
the door and new gaskets can be “pressed” back into
place.
Drawer Assembly Cleaning
The drawer assembly is designed to be cleaned easily. Both
drawer and tracks are removable without tools. The drawer
tracks are dishwasher safe or can be cleaned in a sink with
detergents and a soft bristle brush. Drawers and tracks should
be cleaned on a weekly basis.
Doors/Hinges
Remove Drawers
Over time and with heavy use the door hinges may
become loose. If it is noticed that the door is beginning
to sag, it may be necessary to tighten the screws that
mount the hinge brackets to the frame of the cabinet,
Pull the drawer box out until it stops. Lift up on the drawer
front and pull the drawer box completely out. Using a soft
bristle brush, clean the track on the bottom of the drawer
box. When finished, it should be wiped clean of all food and
debris.
Tracks
Figure 6. Door Hinge
Figure 6. If the doors are loose or sagging, this can cause
the hinge to pull out of the frame which may damage
both the doors and the door hinges. In some cases
this may require repair by a qualified service agent or
maintenance personnel.
Drain Maintenance
Each cabinet has a drain located inside which removes the
condensation from the evaporator coil and evaporates
it at an external condensate evaporator pan. Each
drain can become loose or disconnected from moving
14
The drawer box
assembly must be
removed. Pull the
drawer tracks out
until they hit a stop.
tab on top of
blue safety clip Locate blue safety clips
towards the back of
each drawer track. Blue safety clips have a tab on the top.
Push the tab back until it clicks. Lift up and pull the drawer
tracks all the way out of the drawer cage. The drawer tracks are
dishwasher safe or can be cleaned in a sink with detergents
and a soft bristle brush. Drawers and tracks should be cleaned
on a weekly basis. Using a soft bristle brush, wash the track
making sure each roller is thoroughly cleaned. The drawer
cage should be cleaned with a soft bristle brush, removing
any food and debris gathered on the bottom ledge. Once it’s
cleaned thoroughly with a soft bristle brush, wipe remaining
debris clean with a soft towel.
Reassembly
Push the drawer tracks into the drawer cage. The blue safety
clip must remain pushed towards the back. Lift up and slide
the drawer track all the way into the drawer cage. The blue
safety clip will lock in place automatically. Once all tracks are
replaced, insert the drawer box. Rest the drawer box bottom
track on the front track roller. Then push the drawer back
in place SLOWLY. When the drawer box is about half way in
Compact Refrigerators
Wiring Diagrams
Flat Top
Refrigerator Units
L1
G
NEMA 5-15P
Supply Cord and
Plug furnished
N
BLACK
WHITE
EVAPORATOR FAN
HPS
TEMPERATURE
CONTROL
CONDENSING
UNIT
Salad Top
Refrigerator Units
NEMA 5-15P
Supply Cord and
Plug furnished
Temperature Control
Knob Access
EVAPORATOR FANS
L1
N
TEMPERATURE
CONTROL
1 3
5
HPS
CONDENSING
UNIT
15
Delfield
Freezer Units' Wiring Diagram
DUAL EVAPORATOR
UNITS ONLY
MULLION
HEATER
16
Compact Refrigerators
STANDARD LABOR GUIDELINES TO REPAIR OR
REPLACE PARTS ON DELFIELD EQUIPMENT
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
A maximum of 1-hour is allowed to diagnose a defective
component.
A maximum of 1-hour is allowed for retrieval of parts not in
stock.
will be reimbursed.
Overtime, installation/start-up, normal control adjustments,
general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed
under warranty unless pre-approved with a Service Work Authorization from Delfield. You must submit the number with
the service claim.
A maximum travel distance of 100 miles round trip and 2-hours
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
• Thermostat
• Evaporator/Condenser Fan Motor and Blade
• Hi-limit/Thermal Protector Switch
• Door Hinges, Locks, and Gaskets
• Compressor Start Components and Overload Protector
LABOR OF 2 HOURS IS ALLOWED TO REPLACE:
• Drawer Tracks/Cartridges
• Locate/Repair a Leak
• Defrost Heater
LABOR OF 3 HOURS IS ALLOWED TO REPLACE:
• Condenser or Evaporator Coil
• Hot gas condensate evaporator
LABOR OF 4 HOURS IS ALLOWED TO REPLACE
Compressor
This includes recovery of refrigerant and leak check.
$55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen, or similar fees.)
REFRIGERANTS
R404A A maximum of $15.00/lb. or $1.00/oz. will be reimbursed.
17
Delfield
Manufacturers Limited Lifetime Warranty
Delfield warrants to the original purchaser-user, subject to the
limitations and exclusions set forth below, that the ABS interior of
the Delfield models identified above will be free of manufactured
defects for as long as the equipment is owned by the original
purchaser-user and is in operation.
What is covered
For purposes of this Warranty, interior liner is defined as the
portion of the interior liner which is made of ABS material. This
Warranty applies only to products sold and installed after March
1, 2000 in the United States, Canada, Puerto Rico, and Mexico.
For purposes of this Warranty, lifetime is defined as the expected
usable life for the equipment of 12 years.
Delfield’s Obligation
Limited strictly to shipping OEM replacement parts or repair kits
for any ABS covered interior. A Delfield authorized service dealer
and Delfield’s Service Department must confirm the liner defect
has occurred under normal conditions and is not due to misuse
as defined below. All decisions regarding the ABS interior shall
be made by Delfield’s Service Department and shall be binding
upon the parties. No labor or service charges or allowances are
covered by this warranty. Warranty service must be performed
by a Delfield approved authorized service agent.
User Responsibility
The product must be installed, cleaned and maintained as
described in the Installation & Operation manual which is furnished with the product. Only approved replacement parts may
be used. Failure to adhere to the requirements of this paragraph
may void warranty coverage.
Procedures
All claims for replacement parts or repair kits must be made
through a Delfield Parts Depot or an authorized Delfield dealer.
The defective part invoice must be returned to Delfield within
15 days after the date of service to be eligible for warranty
coverage. All claims must include the model, serial number,
an original date of installation and customer identification. Use
18
of parts other than original Delfield replacement parts will not
be covered.
Exclusions
This warranty does not cover labor, service, charges for travel
time, mileage, or premium charges. This warranty also does
not include defects resulting from:
Operation of the product beyond the specification set forth in
the Service and Installation Manual.
Failure to clean and maintain the product as described in the
Service and Installation Manual.
Installation of the product in a manner other than as set forth
in the Service and Installation.
Use or installation of replacement parts not approved by Delfield:
or The introduction of hot items directly onto the ABS liner.
This warranty is in lieu of all other warranties or guarantees of any kind, express or implied, except Delfield’s One
Year Parts and 90-Day Warranty 4400 Series. ANY IMPLIED
WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND
EXCLUDED. IN NO EVENT SHALL DELFIELD BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND
OR NATURE, OR FOR ANY DEFECT RESULTING IN WHOLE OR
IN PART FROM MISUSE, ALTERATION, IMPROPER INSTALLATION OR INADEQUATE MAINTENANCE OF THE PRODUCT
OR ANY PART THEREOF.
No part or assembly which has been subject to accident, alteration or misuse, or which has not been installed or serviced in
accordance with the Installation & Operation Manual furnished
with the product, or which is from equipment on which the
serial number has been altered or removed, shall be covered
by this warranty.
Compact Refrigerators
STANDARD ONE YEAR WARRANTY (One year parts, 90 days labor)
The Delfield Company (“Delfield”) warrants to the Original Purchaser of
the Delfield product (herein called the “Unit”) that such Unit, and all parts
thereof, will be free from defects in material and workmanship under normal
use and service for a period of one (1) year from the date of shipment of
the Unit to the Original Purchaser or, if the Original Purchaser returns
the warranty card completely filled out including the date of installation
within thirty (30) days of receipt of the Unit, one (1) year from the date
of installation. During this one year warranty period, Delfield will repair
or replace any defective part or portion there of returned to Delfield by the
Original Purchaser which Delfield determines was defective due to faulty
material or workmanship. The Original purchaser will pay all labor, crating,
freight and related costs incurred in the removal of the Unit of defective
component and shipment to Delfield, except that during a period of either
ninety (90) days from the date of shipment of the Unit to the Original
Purchaser or, if the Original Purchaser returns the warranty card completely
filled out including the date of installation within thirty (30) days of receipt
of the Unit, ninety (90) days from the date of installation Delfield will pay
all related labor costs. Delfield will pay the return costs if the Unit or part
thereof was defective.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
This warranty does not apply to any Unit or part thereof that has been
subjected to misuse, neglect, alteration, or accident, such as accidental
damage to the exterior finish, operated contrary to the recommendations
specified by Delfield; or repaired or altered by anyone other than Delfield in
any way so as to, in Delfield’s sole judgement, affect its quality or efficiency.
This warranty does not apply to any Unit that has been moved from the
location where it was originally installed. This warranty also does not cover
the refrigerator drier or the light bulbs used in the Unit. The warranty is
subject to the user’s normal maintenance and care responsibility as
set forth in the Service and Installation Manual, such as cleaning the
condenser coil, and is in lieu of all other obligations of Delfield. Delfield
neither assumes, nor authorizes any other person to assume for Delfield,
any other liability in connection with Delfield’s products.
Removal or defacement of the original Serial Number or Model Number from
any Unit shall be deemed to release Delfield from all obligations hereunder
or any other obligations, express or implied.
Parts furnished by suppliers to Delfield are guaranteed by Delfield only to
the extent of the original manufacturer’s express warranty to Delfield. Failure
of the Original Purchaser to receive such manufacturers warranty shall in
no way create any warranty, expressed or implied, or any other obligation
or liability on Delfield’s part in respect thereof.
IF THE CUSTOMER IS USING A PART THAT RESULTS IN A VOIDED
WARRANTY AND A DELFIELD AUTHORIZED REPRESENTATIVE TRAVELS
TO THE INSTALLATION ADDRESS TO PERFORM WARRANTY SERVICE, THE
SERVICE REPRESENTATIVE WILL ADVISE CUSTOMER THE WARRANTY
IS VOID. SUCH SERVICE CALLS WILL BE BILLED TO CUSTOMER AT
THE AUTHORIZED SERVICE CENTER’S THEN APPLICABLE TIME AND
MATERIALS RATES. CONSIDER: CUSTOMER MAY INITIATE A SERVICE
AGREEMENT WITHOUT PARTS COVERAGE.
The installation contractor shall be responsible for building access, entrance
and field conditions to insure sufficient clearance to allow any hood(s),
vent(s), or Unit(s) if necessary, to be brought into the building. Delfield
will not be responsible for structural changes or damages incurred during
installation of the Unit or any exhaust system.
Delfield shall not be liable in any manner for any default or delay in performance
hereunder caused by or resulting from any contingency beyond Delfield’s
control, including, but not limited to, war, governmental restrictions or
restraints, strike, lockouts, injunctions, fire, flood, acts of nature, short
or reduced supply of raw materials, or discontinuance of the parts by the
original part manufacturer.
Except as provided in any Additional Four Year Protection Plan, if
applicable, and the Service Labor Contract, if applicable, the foregoing
is exclusive and in lieu of all other warranties, whether written or oral,
express or implied. This warranty supersedes and excludes any prior oral
or written representations or warranties. Delfield expressly disclaims any
implied warranties of merchantability, fitness for a particular purpose of
compliance with any law, treaty, rule or regulation relating to the discharge
of substances into the environment. The sole and exclusive remedies of
any person relating to the Unit, and the full liability of Delfield for any
breach of this warranty, will be as provided in this warranty.
Other than this Delfield Standard One Year Limited Warranty, any applicable
Delfield Additional Four Year Protection Plan or applicable Delfield Service
Labor Contract, the Original Purchaser agrees and acknowledges that no
other warranties are offered or provided in connection with or for the unit
or any other part thereof.
In no event will Delfield be liable for special, incidental or consequential
damages, or for damages in the nature of penalties.
IF DURING THE WARRANTY PERIOD, CUSTOMER USES A PART FOR
THIS DELFIELD EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR
RECYCLED PART PURCHASED DIRECTLY FROM DELFIELD OR ANY OF
ITS AUTHORIZED SERVICE CENTERS AND/OR THE PART BEING USED IS
MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL
BE VOID. FURTHER, DELFIELD AND ITS AFFILIATES WILL NOT BE LIABLE
FOR ANY CLAIMS DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER
WHICH ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE
TO THE INSTALLATION OF ANY MODIFIED PART AND/OR PART RECEIVED
FROM AN UNAUTHORIZED SERVICE CENTER. If the warranty becomes void,
Customer may purchase from Delfield, if available, a Service Agreement
or service at the then current time and materials rate.
For more information on Delfield warranty’s log on and check out the service
section of our web site at www.delfield.com.
If shipment of a replacement part is requested prior to the arrival in the
Delfield factory of the part claimed to be defective, the Original Purchaser
must accept delivery of the replacement part of a C.O.D. basis, with credit
being issued after the part has been received and inspected at Delfield’s
plant and determined by Delfield to be within this warranty.
Under no condition does this warranty give the Original Purchaser the right
to replace the defective Unit with a complete Unit of the same manufacturer
or of another make. Unless authorized by Delfield in writing, this warranty
does not permit the replacement of any part, including the motor-compressor,
to be made with the part of another make or manufacturer.
No claims can be made under this warranty for spoilage of any products
for any reason, including system failure.
19
Delfield
™
Mt. Pleasant, MI
®
Covington, TN
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous customer
service reps by having your model number and serial number available at the time
of your call (800) 733-8829.
Model:________________________ S/N: _ ______________________
Installation Date:_ _______________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com.
Delfield
™
®
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2010 The Delfield Company. All rights reserved. Printed in the U.S.A.
DM44_4500 09/10
9294098