Dream Vision Inti+ User manual

Changes
Dreamvision provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not
limited to the implied warranties or merchantability and fitness for a particular purpose. Dreamvision may make
improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the
information in this publication; these changes are incorporated in new editions of this publication.
Copyright
All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Dreamvision.
Guarantee
Dreamvision provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults. Dreamvision must be informed immediately in writing of
any complaints.
If the purchaser or third party caries out modifications or repairs on goods delivered by Dreamvision, or if the goods
are handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of
risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will
be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or
special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance
are not subject to the guarantee provided by Dreamvision either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must
be complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of
their respective holders. All brands and product names mentioned in this manual serve as comments or examples
and are not to be understood as advertising for the products of their manufactures.
2
R699800 - Inti Series User Manual
TABLE OF CONTENTS
1.0
SAFETY INSTRUCTIONS ............................................................................................. 5
1.1
1.2
1.3
2.0
INSTALLATION GUIDELINES .................................................................................... 8
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
3.0
General View ................................................................................................................................... 18
Connecting the Power Cord ............................................................................................................. 19
Operating LEDs ............................................................................................................................... 20
Operating and Navigation Buttons .................................................................................................. 21
CONNECTIONS............................................................................................................. 22
5.1
5.2
5.3
6.0
General View ................................................................................................................................... 16
Loading and replacing batteries ....................................................................................................... 16
How to use the Remote Control Unit............................................................................................... 17
GETTING STARTED .................................................................................................... 18
4.1
4.2
4.3
4.4
5.0
About 3D Content and 3D Projection................................................................................................ 8
Comfort and Caution ......................................................................................................................... 9
3D-Synchro Emitter ........................................................................................................................... 9
Environment of Use ......................................................................................................................... 10
Air-Flow and Space Requirements .................................................................................................. 10
Ceiling Mounting the Unit ............................................................................................................... 11
Projection Distance .......................................................................................................................... 12
Setting the Lens Shift....................................................................................................................... 12
REMOTE CONTROL UNIT (RCU) ............................................................................ 16
3.1
3.2
3.3
4.0
Important Information........................................................................................................................ 5
Important Safeguards ......................................................................................................................... 5
REGIONAL SPECIFIC INFORMATION......................................................................................... 7
Connecting a Video Source to the Projector .................................................................................... 22
Connecting an Automation / Control device.................................................................................... 23
Caution when connecting a device to HDMI input ......................................................................... 24
MENU AND PICTURE SETTING............................................................................... 25
6.1
6.2
6.3
6.4
Menu Structure ................................................................................................................................ 25
Picture Adjust menu......................................................................................................................... 29
Picture Mode ..................................................................................................................... 29
Color Profiles (Inti 2 & Inti 3) .......................................................................................... 29
Color Temperature............................................................................................................. 29
Gamma .............................................................................................................................. 29
Film Tone (Inti 2 & Inti 3, Film Picture Profile)............................................................... 30
Dark / Bright Level ........................................................................................................... 30
Contrast ............................................................................................................................. 30
Brightness.......................................................................................................................... 30
Color.................................................................................................................................. 30
Tint .................................................................................................................................... 30
Advanced........................................................................................................................... 30
Reset.................................................................................................................................. 31
Input Signal menu ............................................................................................................................ 31
HDMI Inputs ..................................................................................................................... 31
Component ........................................................................................................................ 32
PC (Inti 2 & Inti 3) ............................................................................................................ 32
Picture Position ................................................................................................................. 32
Aspect Ratio ...................................................................................................................... 32
Mask.................................................................................................................................. 34
Progressive (only 480i, 576i, 1080i) ................................................................................. 34
Installation Menu ............................................................................................................................. 34
Lens Control...................................................................................................................... 34
Pixel Adjust ....................................................................................................................... 34
Installation Style................................................................................................................ 34
Keystone............................................................................................................................ 34
R699800 - Inti Series User Manual
3
6.5
6.6
6.7
6.8
7.0
ANAMORPHIC LENS .................................................................................................. 38
7.1
7.2
7.3
7.4
8.0
Clean Dirt on the Cabinet ................................................................................................................ 41
Dirt on the Lens ............................................................................................................................... 41
Replacing the Lamp ......................................................................................................................... 41
Cleaning and Replacing the Dust Filters ......................................................................................... 42
Troubleshooting ............................................................................................................................... 43
MISCELLANEOUS ....................................................................................................... 44
9.1
9.2
9.3
9.4
9.5
4
Optional 2.35 CineWide and 2.35 THEATRE System (for Inti) ..................................................... 38
Using the Remote Control Unit. ...................................................................................................... 38
2.35 CineWide ................................................................................................................................. 39
2.35 THEATRE System (for Inti) .................................................................................................... 39
MAINTENANCE............................................................................................................ 41
8.1
8.2
8.3
8.4
8.5
9.0
Anamorphic (not available with 3D sources).................................................................... 34
Screen Adjust .................................................................................................................... 35
Black Level ....................................................................................................................... 35
Display Setup Menu......................................................................................................................... 35
Back Color ........................................................................................................................ 35
Menu Position ................................................................................................................... 35
Menu Display .................................................................................................................... 35
Line Display ...................................................................................................................... 36
Source Display .................................................................................................................. 36
Logo .................................................................................................................................. 36
Language ........................................................................................................................... 36
Function Menu ................................................................................................................................. 36
Off-Timer .......................................................................................................................... 36
High Altitude Mode........................................................................................................... 36
Communication Terminal (Inti 2 & Inti 3)........................................................................ 36
Network (Inti 2 & Inti 3)................................................................................................... 36
Lamp Reset........................................................................................................................ 36
Information Menu ............................................................................................................................ 36
Input Source ...................................................................................................................... 36
Source................................................................................................................................ 36
Resolution ......................................................................................................................... 36
H. Frequency ..................................................................................................................... 36
V. Frequency ..................................................................................................................... 36
Deep Color ........................................................................................................................ 37
Lamp Time ........................................................................................................................ 37
Expert Calibration (Inti 2 & Inti 3) .................................................................................................. 37
RS-232 protocol ............................................................................................................................... 44
LAN protocole (Inti 2 & Inti 3) ....................................................................................................... 49
Infra Red, long hex-pronto compatible RCU................................................................................... 50
PC compatible signals...................................................................................................................... 51
Specifications................................................................................................................................... 52
R699800 - Inti Series User Manual
1.0 SAFETY INSTRUCTIONS
1.0 SAFETY INSTRUCTIONS
1.1
Important Information
Lead-free regulation
This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains
lead in some components.
Disposal of these materials may be regulated in your community due to environmental considerations. For disposal
or recycling information please contact your local authorities, or the Electronics Industries Alliance: http://
www.eiae.org.
Information for Users on Disposal of Old Equipment
This symbol indicates that the electrical and electronic equipment should not be disposed as general
household waste at its end of life. Instead, the product should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment for proper treatment, recovery
and recycling in accordance with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources and will help
prevent potential negative effects on the environment and human health which could otherwise be caused by
inappropriate waste handling of this product.
For more information about collection point and recycling of this product, please contact your local municipal office,
your household waste disposal service or the shop where you purchased the product. Penalties may be applicable
for incorrect disposal of this waste, in accordance with national legislation.
Other Countries outside the European Union:
If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules
in your country for the treatment of old electrical and electronic equipment.
About the installation place
Do not install the projector in a place that cannot support its weight securely.
If the installation place is not sturdy enough, the projector could fall or overturn, possibly causing personal injury.
CAUTION:
To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel. This
projector is equipped with a 3-blade grounding type plug to satisfy FCC rule. If you are unable to insert the plug
into the outlet, contact your electrician.
WARNING:
To prevent fire or shock hazards, do not expose this appliance to rain or moisture. This apparatus must be
earthed.
1.2
Important Safeguards
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure
your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for
its installation, use and service.
The power input is auto-ranging from 100 to 240 VAC.
Please read these Important Safeguards carefully before use.
•
All the safety and operating instructions should be read before the product is operated.
•
All warnings on the product and in the operating instructions should be adhered to.
•
All operating instructions should be followed.
•
Place the projector near a wall outlet where the plug can be easily unplugged.
•
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
•
Do not use attachments not recommended by the product manufacturer as they may be hazardous.
•
Do not use this product near water. Do not use immediately after moving from a low temperature to high
R699800 - Inti Series User Manual
5
1.0 SAFETY INSTRUCTIONS
opening or removing covers may expose you to
dangerous voltages and other hazards. Refer all
service to qualified service personnel.
temperature, as this causes condensation, which
may result in fire, electric shock, or other
hazards.
•
Do not place this product on an unstable cart,
stand, or table. The product may fall, causing
serious injury to a child or adult, and serious
damage to the product. The product should be
mounted according to the manufacturer’s
instructions, and should use a mount
recommended by the manufacturer.
•
When the product is used on a cart, care should
be taken to avoid quick stops, excessive force,
and uneven surfaces which may cause the
product and cart to overturn, damaging
equipment or causing possible injury to the
operator.
•
Slots and openings in the cabinet are provided
for ventilation. These ensure reliable operation of
the product and protect it from overheating.
These openings must not be blocked or covered.
(The openings should never be blocked by
placing the product on bed, sofa, rug, or similar
surface. It should not be placed in a built-in
installation such as a bookcase or rack unless
proper ventilation is provided and the
manufacturer’s instructions have been adhered
to). For proper ventilation, separate the product
from other equipment, which may prevent
ventilation and keep a distance of more than 5-9”
(150 mm).
•
•
•
•
This product is equipped with a three-wire plug.
This plug will fit only into a grounded power
outlet. If you are unable to insert the plug into the
outlet, contact your electrician to install the
proper outlet. Do not defeat the safety purpose of
the grounded plug.
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular
attention to cords at doors, plugs, receptacles,
and the point where they exit from the product.
For added protection of this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the cable system. This
will prevent damage to the product due to
lightning and power line surges.
•
Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as
this can result in a risk of fire or electric shock.
•
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
•
6
This product should be operated only with the
type of power source indicated on the label. If you
are not sure of the type of power supply to your
home, consult your product dealer or local power
company.
Do not attempt to service this product yourself as
•
Unplug this product from the wall outlet and refer
service to qualified service personnel under the
following conditions:
a) When the power supply cord or plug is
damaged.
b) If liquid has been spilled, or objects have fallen
on the product.
c) If the product has been exposed to rain or
water.
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the Operation
Manual, as an improper adjustment of controls may
result in damage and will often require extensive
work by a qualified technician to restore the product
to normal operation.
e) If the product has been dropped or damaged in
any way.
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
•
When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or with same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
•
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
•
The product should be placed more than one foot
away from heat sources such as radiators, heat
registers, stoves, and other products (including
amplifiers) that produce heat.
•
When connecting other products such as VCR’s,
and personal computers, you should turn off the
power of this product for protection against
electric shock.
•
Do not place combustible behind the cooling fan.
For example, cloth, paper, matches, aerosol cans
or gas lighters that present special hazards when
over heated.
•
Do not look into the projection lens while the
illumination lamp is turned on. Exposure of your
eyes to the strong light can result in impaired
eyesight.
•
Do not look into the inside of this unit through
vents (ventilation holes), etc. Do not look at the
illumination lamp directly by opening the cabinet
while the illumination lamp is turned on. The
illumination lamp also contains ultraviolet rays
and the light is so powerful that your eyesight can
be impaired.
•
Do not drop, hit, or damage the light-source lamp
(lamp unit) in any way. It may cause the lightsource lamp to break and lead to injuries. Do not
use a damaged light source lamp. If the lightsource lamp is broken, ask your dealer to repair
R699800 - Inti Series User Manual
1.0 SAFETY INSTRUCTIONS
it. Fragments from a broken light-source lamp may cause injuries.
•
The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the
light source lamp. If anything is unclear, please consult your dealer.
•
Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching fixture of the
projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal
injury.
•
Use only the accessory cord designed for this product to prevent shock.
•
The power supply voltage rating of this product is AC120 V, AC100 V – AC240 V, the power cord attached
conforms to the following power supply voltage. Use only the power cord designated by our dealer to ensure
Safety and EMC.
•
When it is used by other power supply voltage, power cable must be changed.
•
Ensure that the power cable used for the projector is the correct type for the AC outlet in your country. Consult
your product dealer.
•
Caution: Do not allow any unqualified person to install the unit. Be sure to ask your dealer to install the unit (e.g.
attaching it to the ceiling) since special technical knowledge and skills are required for installation. If installation
is performed by an unqualified person, it may cause personal injury or electrical shock.
1.3
REGIONAL SPECIFIC INFORMATION
FCC INFORMATION (USA ONLY)
Changes or modification not approved by Dreamvision could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encourage to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC
The Federal Communications Commission (FCC) is an independent United States government agency, created,
directed, and empowered by Congressional statute.
The FCC was established by the Communications Act of 1934 as the successor to the Federal Radio Commission
and is charged with regulating all non-Federal Government use of the radio spectrum, including radio and television
broadcasting, and all interstate telecommunications like wire, satellite and cable as well as all international
communications that originate or terminate in the United States. The FCC's jurisdiction covers the 50 states, the
District of Columbia, and U.S. possessions.
R699800 - Inti Series User Manual
7
2.0 INSTALLATION GUIDELINES
2.0 INSTALLATION GUIDELINES
2.1
About 3D Content and 3D Projection
This unit is compatible with 3D playback. The source can be connected using one of the two available HDMI 1.4a
inputs. The 3D effect is based on the binocular parallax which is the difference of the view on a single object when
seen from the left and right eyes, respectively.
L
R
Binocular parallax
3D movies use two sets of images: one set for the left eye, the other set for the right eye. These images can be
stored into three compatible formats: Frame packing, Top-&-Bottom or Side-by-Side.
The 3D scheme of this unit decodes the source and converts it into a frame sequential format for 3D projection,
alternating the images produced for the left and right eye.
Storing Formats
Frame packing
L
R
L
Top and Bottom
Projection Format
R
L
L
L
L
R
R
L
L
R
R
R
R
L
R
Side by Side
L
L
R
L
R
L
R
R
Compatible source formats and Projection format
This unit is compatible with the following 3D formats:
•
1080p @ 23.98/24Hz - Frame Packing (Blu-ray movies)
•
720p @ 50 or 59.94/60Hz - Frame Packing (gaming)
•
720p @ 50 or 59.94/60Hz - Top-Bottom
•
1080p @ 23.97/24hz - Top-Bottom
• 1080i@ 50 or 59.94/60Hz - Side-by-Side
The left and right images are produced alternatively. Therefore, the shutter glasses are used to separate the left eye
images which will be only visible to the left eye, and the right eye images only visible to the right eye. The human
brain then perceives stereo objects based on the visual differences between two images of the same object but
taken from different angles.
8
R699800 - Inti Series User Manual
2.0 INSTALLATION GUIDELINES
L
R
L
L
R
R
The shutter glasses are used to separate the left and right image, therefore producing a 3D effect.
2.2
Comfort and Caution
The closer one looks at stereoscopic images, the greater the binocular disparity, which means greater perception of
outward projection. At the same time, the spectator must focus on these outward objects on the screen. The
projecting image and the real focus distance cause a great contradiction. This causes visual fatigue and discomfort.
That means that the more 3D effect, the more outward effects, and the more your eyes will try to focus nearer than
where the objetcs are actually -really- located.This strain contributes to fatigue and discomfort.
CAUTION ABOUT HEADACHES AND EYE STRAINS
Please stop watching if you do not feel well and consult a physician if necessary. People who already have a kind of
photosensitivity, sufferers from heart disease, and people in poor physical condition should not watch 3D video
images of this device, which makes use of 3D glasses. It is recommended that you take a break periodically.
Prevent child under 5 years old to watch 3D
The comprehensive brain function to judge stereoscopic vision which includes the feeling for real distances,
develops while growing up by touching and seeing real objects, but in early childhood, it is still in an underdeveloped
state. Even though there are individual differences, children under 5 are still developing. Letting them frequently
watch virtual 3D video images can be an obstacle for the development of a comprehensive three-dimensional feel.
For younger children may suddenly become sick, because they continue watching without realizing symptoms like
3D sickness or deterioration of health until after watching 3D images. Please accompany your child while it watches
3D programs.
2.3
3D-Synchro Emitter
In order to match the timing of the displayed video images with the timing of the opening/closing 3D glasses
shutters for each eye, the projector in 3D mode sends the correct synchro data to the 3D synchro emitter.
3D GLASSES SYNCHRONIZATION
In regard to the Infrared 3D emitter model, if you experience synchro issues with Infra Red glasses in an installation
where the synchro signal is bouncing from the projection screen, please direct the 3D emitter in such a way towards
the seats that the infrared rays can directly reach the 3D glasses. In a few cases the synchronization may not work
correctly:
-If you are near infrared communication equipment or lighting equipment.
-If the 3D-glasses do not face directly to the 3D synchro emitter
Depending on the use of 3D emitters such as Radio Frequency synchro emitter, it may be possible that its operation
influences the operation of other devices using the same bandwidth.
R699800 - Inti Series User Manual
9
2.0 INSTALLATION GUIDELINES
2.4
Environment of Use
Do not use this unit in rooms with cigarette smoke or oily smoke. This may cause the unit to malfunction.
Mounting this unit to the ceiling
Check temperature around the unit. When a heater is in use, the ceiling may reach a temperature higher than
anticipated, hence leading to malfunction of the unit.
Precautions of Usage
This unit makes use of a light source lamp that may reach a high temperature during projection. Do not allow
projection under the following conditions. Doing so may cause fire or malfunction of the unit.
•
Projection with the unit laid on sides.
•
Projection with the unit installed in an unreasonable angle. Avoid using this unit at an angle of more than 15°
horizontally and 5° vertically. Doing so may cause unevenness in the color or shorten the lamp life.
•
Projection at a location that blocks the air inlets or exhaust vents.
•
Projection at a place exposed to air blasts from an air conditioner.
2.5
Air-Flow and Space Requirements
This unit can be installed in table, ceiling, rear table or rear ceiling position. Make sure that the unit is installed within
the space requirements described below.
A
B
B
A
B
A
A
•
A: Air inlets
•
B: Air outlet
Air flow
200 mm
200 mm
100 mm
200 mm
Space requirements
10
R699800 - Inti Series User Manual
2.0 INSTALLATION GUIDELINES
2.6
Ceiling Mounting the Unit
When mounting of this unit is required, make use of the 4 screw holes (M5x20 screws) at the bottom of this
unit indicated by the letter A. Allow sufficient space around the air inlets to avoid blocking them.
Precautions for Ceiling-mount
•
To ceiling-mount this unit, special expertise and techniques are
necessary. Be sure to ask your dealer or specialist to perform
mounting.
•
Do not mount at places that may be subjected to vibration and shock.
•
Depth of the screw holes (A) is 23 mm. Use at least 13mm long
screws but not longer than 23mm as you may damage inside the
projector.
•
Install at a safe place in case this unit or a part of it may drop. If the
light-source lamp is broken, small pieces of glass from the mesh of
the filter may appear outside the unit.
•
Regardless whether the unit is still under guarantee, Dreamvision is
not liable for any product damage caused by mounting the unit with
third party ceiling mount or when the environment is not suitable for
ceiling-mount.
R699800 - Inti Series User Manual
A
A
A
A
11
2.0 INSTALLATION GUIDELINES
2.7
Projection Distance
Projection Distance
Projection Screen Size
Diagonal size
(Aspect Ratio 16:9)
Projection Screen Size
Base size
(Aspect Ratio 16:9)
Projection Screen
Height
(Aspect Ratio 16:9)
Inti Series
50" (1270 mm)
43,6" (1107 mm)
24,5" (623 mm)
151 cm - 305 cm
60" (1524 mm)
52,3" (1328 mm)
29,4" (747 mm)
178 cm - 366 cm
70" (1778 mm)
61,0" (1550 mm)
34,3" (872 mm)
209 cm - 428 cm
83" (2108 mm)
72,3" (1837 mm)
40,7" (1034 mm)
251 cm - 507 cm
92" (2337 mm)
80,2" (2037 mm)
45,1" (1146 mm)
279 cm - 562 cm
100" (2540 mm)
87,2" (2214 mm)
49,0" (1245 mm)
301 cm - 613 cm
110" (2794 mm)
95,9" (2435 mm)
53,9" (1370 mm)
331 cm - 675 cm
138" (3505 mm)
120,3" (3055 mm)
67,7" (1718 mm)
418 cm - 843 cm
150" (3810 mm)
130,7" (3321 mm)
73,5" (1868 mm)
453 cm - 860 cm
180" (4572 mm)
156,9" (3985 mm)
88,2" (2241 mm)
545 cm - 1107 cm
200" (5080 mm)
174,3" (4428 mm)
98,1" (2491 mm)
6060 cm - 1230 cm
Projecting Distance
minimum - maximum
•
The projection screen sizes and projecting distances in the table above are provided only as a guide. Please use
them as reference during installation.
•
Use a projection image of 16:9 aspect ratio for setup adjustment.
Projection Distance for 3D
It is true that the perception of the 3D effect will vary according to your seat position but in a smaller scale than with
real 3D objects much more like holograms. You cannot go on the side of the screen and actually see the side of the
object because the subject of the picture is shot only within two angles.
When a movie is shot with a 3D camera, the director knows at witch distance the effect will be perceived and witch
depth he intends to gives to the objects. It is recommended to watch from a distance three times the height of the
screen to reduce the eye strains.
H = Screen Height
Distance = 3 x H
Recommended projection distance for 3D
2.8
Setting the Lens Shift
The optimum image can be obtained when the centre of this projector’s lens and the screen are placed
perpendicular to each other. Take note of the projection angle when placing them. You can also use up to +/- 15° up
12
R699800 - Inti Series User Manual
2.0 INSTALLATION GUIDELINES
and down position and configure trapezoidal correction.
Horizontal Shift +/- 34%
Vertical Shift
+/- 80%
Screen Height
(H)
Screen Base (B)
This unit comes with a vertical and horizontal shift to suit most installations. Make sure that your installation
does not exceed 80% vertical offset and 34% horizontal offset to avoid trapezoidal correction.
This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen position.
Adjust the picture to your screen.
•
The Vertical Shift level is between -80% and 80% of the Screen Height (0.80 x H).
•
The Horizontal Shift level is between -34% and 34% of the Screen Base (0.34 x B).
•
The shift level is set to 0% vertically and horizontally by default, that means that the optical lens is aligned with
the center of the screen.
•
If the projector is not installed vertically, use trapezoidal Correction to fulfill your screen.
•
If you plan to use both the vertical and horizontal shifts, make sure to not exceed the values contained in the tab
below:
Left - Right shift
max. Up - Down shift
2.8.0.1
0%
5% 10% 15% 20% 25% 30% 34%
80% 74% 66% 57% 47% 34% 18% 0%
Adjust the picture position
The Inti Series projector has motorized vertical and horizontal shifts. Browse into the Menu to the [Lens Control]
setting into the [Installation] menu, select the shift adjustment. Or use the direct access button on the Remote
Control Unit [Lens Control] to make the lens control adjustment.
You can use self-generated test pattern of the projector or an external pattern, from a calibration DVD by example,
R699800 - Inti Series User Manual
13
2.0 INSTALLATION GUIDELINES
by setting the Adjust pattern option to Off.
STAND BY
ON
INPUT
LENS
CONTROL
LIGHT
PICTURE MODE
STAND BY
ON
INPUT
LENS
CONTROL
LIGHT
PICTURE MODE
Select the [Shift] adjustment and move the picture with the navigation buttons.
Adjust the Picture Focus
Into the [Lens Control] menu, press the [Ok] button to access the [Focus] adjustment. Use the up and down buttons
to adjust the picture focus.
STAND BY
ON
INPUT
LENS
CONTROL
LIGHT
PICTURE MODE
Select the [Focus] adjustment and obtain a clear picture using [Up] and [Down] buttons.
Adjust the picture Zoom
Into the [Lens Control] menu, press the [Ok] button to access the [Zoom] adjustment. Use the up and down buttons
14
R699800 - Inti Series User Manual
2.0 INSTALLATION GUIDELINES
to adjust the picture size until the screen is completely filled.
STAND BY
ON
INPUT
LENS
CONTROL
HIDE
MENU
LIGHT
BACK
PICTURE MODE
Select the [Zoom] adjustment and resize the picture using [Up] and [Down] buttons.
R699800 - Inti Series User Manual
15
3.0 REMOTE CONTROL UNIT (RCU)
3.0 REMOTE CONTROL UNIT (RCU)
3.1
General View
STAND BY
ON
[Stand By] button
[Power On] button
INPUT
HDMI 1
HDMI 2
ASPECT
ANAMO
LENS
CONTROL
LENS AP.
COMP.
Select Active [Input]
C.M.D
Crystal Motion Drive
[Aspect] Ratio
[Anamo]rphic mode
[Lens control]
Shift, Focus and Zoom
[Hide] Display
Lens Aperture
HIDE
LIGHT
Backlight button
Confirm button
Navigation buttons
Display [Menu]
BACK
MENU
[Back] to previous menu
PICTURE MODE
Select Picture mode
Film, Cinema, Anime
Natural, Stage, 3D
User1, User2, User3
Gamma Adj.
FILM
CINEMA
ANIME
NATURAL
STAGE
3D
USER1
USER2
USER3
GAMMA
COLOR
TEMP
Color temp. Adj.
3.2
16
COLOR
P.FILE
PIC.
ADJ.
Basic Picture Adj.
Color Profile
Loading and replacing batteries
•
Push the cover tab with the fingernail a little backwards and pull upwards the cover top.
Slide the cover forward to remove.
•
Push the battery body towards the spring and lift up to remove.
Insert two AAA size batteries, making sure the polarities match the + and - marks inside the battery
compartment.
•
Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until
it is firmly closed.
R699800 - Inti Series User Manual
3.0 REMOTE CONTROL UNIT (RCU)
CAUTION WHEN USING BATTERIES
Do not mix new and old batteries.Do not mix different type of batteries as they are different in characteristics. Insert
batteries according to the + and - marks on the battery case. Do not put batteries into fire or recharge them if they
are not design to. Remove the batteries if the remote control is not to be used for a prolonged period. Use
manganese batteries wherever possible, Do not use rechargeable batteries.
NOTICE
If the remote control has to be brought closer to the projector to operate, it means that the batteries are wearing out.
When this happens, replace the batteries. Insert the batteries according to the + and - marks.
3.3
How to use the Remote Control Unit
The operable distance of the remote control unit is about 7m for direct reception and within 30 degree angle with
respect to the sensor.
Front InfraRed sensor
Back InfraRed sensor
The remote control unit can be used by having the transmission signal reflected off a screen, as the effect of
signals reflected from the RCU differ with the type of screen used, operable distance may decrease.
R699800 - Inti Series User Manual
17
4.0 GETTING STARTED
4.0 GETTING STARTED
4.1
General View
Front side
Optical Lens & Lens cover
Air Outlet
Operating LED
Front IR sensor
•
Optical Lens & Lens cover where the projection light beam is emitted.
•
Operating LEDs: see section 4.3, page 20 for more details.
•
Air Outlets: see “Air-Flow and Space Requirements”, page 10.
Rear side
Input Panel
Lamp trap
Operating buttons
Main Power
18
Air Inlet
•
Input Panel: connect your video source to the correct input.
•
Operating and Navigation buttons described in section 4.4, page 21.
•
Main Power: connect the power cord as shown below.
•
Lamp trap: see “Procedure for Lamp Replacement”, page 41 for more details about lamp replacement.
•
Air Inlets: see “Air-Flow and Space Requirements”, page 10.
R699800 - Inti Series User Manual
4.0 GETTING STARTED
4.2
Connecting the Power Cord
•
Before plugging in the Power Cord, ensure that all devices have been connected
to their respective inputs to this unit.
•
Connect the power cord to the power input terminal of the projector.
CAUTION AGAINST FIRE AND ELECTRIC SHOCK
Since the power consumption of this unit is high, insert the power plug directly into a wall outlet.
When not using devices, remove the power plug from the wall outlet.
Do not use power cords for connection other than specified.
Do not use a power voltage different from that which is indicated.
Do not cut, tear or modify the power cords. Also, do not place a heavy object on, heat or stretch the power cords as
this may cause damage to the cords.
Do not insert or pull plugs with a wet hand.
R699800 - Inti Series User Manual
19
4.0 GETTING STARTED
4.3
Operating LEDs
WARNING
(orange/red LED)
LAMP (orange LED)
STANDBY/ON
(green/red LED)
Operating LED
ID
Description
STANDBY/ON
(green or red)
LAMP
(orange)
WARNING
(orange/red)
Blinking
1
red
-
-
-
Unit is in standby mode
2
green
-
-
-
Unit is in operate mode (during projection)
3
blinking green
-
-
Yes
Unit is in operate mode, but HIDE is ON.
Press again the HIDE button to obtain a
picture.
4
blinking red
-
-
Yes
Unit is in cooldown mode. (switching off)
5/6
-
orange
-
-
Lamp time has reached 2900 hours,
prepare to replace the lamp before 3000
hours.
CAUTION
When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air inlets/exhaust vents by
standing the projector on its end or laying it on its side.
NB: When the projector is running for more than 1 minute, the Standby/ON LED will automatically switch
OFF.
20
R699800 - Inti Series User Manual
4.0 GETTING STARTED
4.4
Operating and Navigation Buttons
Power button
STANDBY/ON
Input source
INPUT
OK
OK
Up - down
Left - right
MENU
BACK
Menu
Back
Button
Description
Power button
To turn On or Off the projector.
Input source
To switch input source.
OK (Enter)
To select or to confirm action.
Up - down - left - right
To navigate into On Screen Display (OSD) Menu.
Menu
To display On Screen Display (OSD) Menu.
Back
To return to previous menu or cancel action.
R699800 - Inti Series User Manual
21
5.0 CONNECTIONS
5.0 CONNECTIONS
This unit can be connected to any compatible devices using the available connections listed below:
Inputs:
•
2x HDMI revision 1.4a with HDCP
•
1x Component (YPbPr / RGB synchro on G)
•
1x PC - VGA (sub D-15) (Inti 2 & Inti 3)
• 1x Optional Remote Terminal (Stereo mini jack)
Outputs and Automation:
•
1x 3D sync signal (3-PIN mini DIN 12V)
•
1x 12V Trigger (Stereo mini jack)
•
1x RS-232
• 1x LAN (Inti 2 & Inti 3)
The RS-232 and LAN ports can be used for automation. For audio output, connect your audio video source to an
amplifier.
5.1
Connecting a Video Source to the Projector
HDMI 1
YPbPr
or
RGB
HDMI 2
3D Syncro
Emitter
VGA
(Sub D-15)
Connection
Device
HDMI1, HDMI2
v1.4a with M3 lock hole
HDMI or DVI-D sources: Blu-Ray Disc player, DVD-player with HDMI, Game
Console, Computer with DVI-D output.
3D Synchro output
3d synchro emitter to control active shutter glasses. 3-PIN mini-DIN
interface, 12V.
YPbPr or RGB (3x RCA)
DVD-Player, HDTV Receiver, Game Console (SD or HD), DVB-T receiver,
Multimedia box, Analog Camera.
VGA (Sub D-15)
(Inti 2 & Inti 3)
For Inti 2 & Inti 3: Computer (VGA output), Multimedia box .
Make sure to use a certified HDMI cable, especially when the distance between the different devices are
longer than 5 meters. If it is the case, the use of a split system or optical fiber cable is highly recommended.
For input resolution and refresh rates, check the “PC compatible signals”, page 51.
22
R699800 - Inti Series User Manual
5.0 CONNECTIONS
5.2
Connecting an Automation / Control device
LAN (**) to Rooter
for Automation
Optional IR-reciever
RS-232 (*)
for Automation
12V Trigger
Connection
Device
RS-232 (*)
Automation Device, Control Device or Computer with RS-232 capability.
Optional IR-receiver
Can be used to connect an external IR receiver when this unit is used in a
dedicated box or in rear projection setup.
12V Trigger
DC power supply output 12V@140-300mA to control either a screen or an
anamorphic slider.
LAN (**)
(Inti 2 & Inti 3)
For Inti 2 & Inti 3: automation Device, Control Device or Computer with RJ45.
(*) USING RS-232 WITH A COMPUTER
The RS-232 Control and Automation may require specific software and tools. See “RS-232 protocol”, page 44 for
more details on RS-232 cabling and protocol.
(**) USING LAN WITH A COMPUTER (INTI 2 & INTI 3 ONLY)
When the LAN Control is selected, the RS-232 port cannot be used for automation. In addition, the control device
must send specific functions to this unit using the Local Network (this is not a web interface) See “LAN protocole
(Inti 2 & Inti 3)”, page 49 for more details on the network configuration and protocol.
CONNECTING AN AUTOMATION/CONTROL DEVICE
This unit can control or be controlled by using several input/output terminals. Each terminal is ruled by specific
protocols. Please refer to Appendix for more information.
R699800 - Inti Series User Manual
23
5.0 CONNECTIONS
5.3
Caution when connecting a device to HDMI input
CAUTION!
Prior to connecting any device to this unit, switch the projector in standby mode
Never connect a HDMI source to this unit when the projector is in operate mode. The HDMI termination is a selfpowered connection and can cause electric discharges.
24
R699800 - Inti Series User Manual
6.0 MENU AND PICTURE SETTING
6.0 MENU AND PICTURE SETTING
6.1
Menu Structure
MAIN MENU
SUBMENU
Picture Adjust
Picture Mode
Inti 2 & Inti 3 (Movies)
Film
(Digital Cinema)
Cinema
(SF movies or anims) Animation
(Video programs)
Natural
(Concerts)
Stage
3D
User1
User2
(Inti One only)
User3
(Inti 2 & Inti 3)
THX
(Inti 2 & Inti 3) Color Profiles
availabble Color Profiles list varies
upon current Picture Mode
(Xenon, Eastman Kodak) Film1
(Xenon, Fujifilm)
Film2
(Extended colors)
Standard
(DCI standard)
Cinema1
(HDTV standard)
Cinema2
(Hollywood anime)
Anime1
(Japanese anime)
Anime2
(TV, sports)
Video
(Games)
Vivid
(Computer/Adobe RGB) Adobe
(Live concerts)
Stage
(Adapted to 3D glasses)
3D
OFF
Color Temp.
AVAILABLE OPTIONS
Preset value:
5500K
6000K
6500K
7000K
7500K
8000K
8500K
9000K
9500K
High brighness(Inti One only)
Brightness
Xenon Modes (Inti 2 & Inti 3)
(Film projector)
(DCI projector)
Cooler temp than X2
Custom Modes:
Xenon1
Xenon2
Xenon3
Custom1
Custom2
Custom3
Custom Modes Gains/Offsets:
R699800 - Inti Series User Manual
25
6.0 MENU AND PICTURE SETTING
Picture Adjust
Gamma
If Picture mode is 3D:
Normal
3D, bright
A (3D)
3D, classic
B (3D)
If Picture mode is Film:
(Eastman)
Film1
(Fujifilm)
Film2
more tone than Film1
Film3
more contrast than Film2 Film4
If Picture mode is not 3D:
focus on tone
A
film S curve
B
more contrast than B
C
brighter
D
Custom1
Custom2
Custom3
Film Tone (Inti 2 & Inti 3)
Dark/Bright Level (Inti 2 & Inti 3)
available when Picture mode is Film:
White
-16 +16
Red
-16 +16
Green
-16 +16
Blue
-16 +16
Dark Level
Bright Level
-7 +7
-7 +7
Contrast
-50 +50
Brightness
-50 +50
Color
-50 +50
Tint (redish to greenish)
-50 +50
Advanced
Sharpness:
Sharpness
Detail Enhancement
Noise Reduction:
RNR
MNR (SD only)
BNR (SD only)
Color Space (Inti One only):
Custom Gamma:
-0 +50
-0 +50
0 - 16
0 - 16
On, Off
Standard
Wide1
Wide2
Custom1
Custom2
Custom3
Correction value
Gamma Adjustment
White
Red
Green
Blue
Color Management (Inti 2 & Inti 3)
Off
Custom1
Custom2
Custom3
Pause
On/Off
Color:
Axis Position
-30 +30
Hue
-30 +30
Saturation
-30 +30
Brightness
-30 +30
26
R699800 - Inti Series User Manual
6.0 MENU AND PICTURE SETTING
Picture Adjust
Advanced
Clear Motion Drive:
Off
Black insertion weak
Mode1
Black insertion strong
Mode2
(interpolation weak)
Mode3
(interpolation strong)
Mode4
(only for 60i or 60p) Film Motion
Clear Motion Drive Demo
Lens Aperture
-15 +0
Lamp Power (Inti 2 & Inti 3):
(160W) Normal
(220W) High
Reset Profile
Input Signal
Confirm
HDMI
Input levels
(16 - 235) Standard
(0 - 255) Enhance
(16 - 255) Super White
Check input levels
pattern
Color Space
Auto
YCbCr(4:4:4)
YCbCr(4:2:2)
RGB
Control with HDMI (CEC)
On, Off
3D Format
Auto
Frame Packing
Side by Side
Top & Bottom
2D
COMP.
Color Space
PC input (Inti 2 & Inti 3)
Picture position
Picture Position
Auto Alignment
Tracking
Phase
Hor., Vert.
Horizontal
Vertical
Aspect (Video only)
if 3D, only 16:9 is available
4:3
16:9
Zoom
Aspect (PC only)
Mask
YCbCr
RGB
Auto
1:1
Full
Off
2.5%
5%
Custom
Left 0% - 5%
Right 0% - 5%
Upper 0% - 5%
Down 0% - 5%
Progressive (480i, 576i, 1080i)
R699800 - Inti Series User Manual
Auto / Off
27
6.0 MENU AND PICTURE SETTING
Installation
Lens Control
Pixel Adjust
Focus
Zoom
Shift
Slide Cover
Adjust Pattern
Lock
horiz. Red
horiz.Green
horiz.Blue
vert. Red
vert. Green
vert. Blue
1-7
1-7
1-7
1-5
1-5
1-5
Installation Style
Horizontal
Vertical
Anamorphic (not available with 3D)
vert. stretch:
hor. sqeeze:
A
B
Off
00 - 99
0 +10
Back Color
Blue, Black
Menu Position
select position
Menu Display
15sec, On
5sec, Off
Source Display (active input)
On, Off
Logo
On, Off
Language
Trigger
Off Timer (in hours)
High Altitude Mode
Communication Terminal
(Inti 2 & Inti 3)
Network
Lamp Reset
Information
-30 +30
-40 +40
Black Level
Line Display (input setting)
Function
Front
Ceiling Mount (Front)
Rear
Ceiling Mount (Rear)
Keystone
Screen Adjust
Display Setup
Auto , Open
On, Off
On, Off
Select between 12 languages
Off
On (Power)
On (Anamorphic)
1H, 2H, 3H, 4H, Off
On, Off
RS-232C
LAN
Displayed if LAN is selected
DHCP Client
On, Off
IP Address
192.168.0.2
Subnet Mask
255.255.255.0
Default Gateway 192.168.0.254
Mac Address
Display MAC
Set
Display network settings
Confirm
Input Terminal
Input Source name
PC Resolution
PC H Freq.
PC V Freq.
Deep Color Depth
Lamp Time
28
R699800 - Inti Series User Manual
6.0 MENU AND PICTURE SETTING
6.2
Picture Adjust menu
Picture Mode
The preset picture modes are available and they can be applied to any input. A picture mode retains the picture
adjustments:
•
Film (Inti 2 & Inti 3) setting is well suited for general movie watching.
•
Cinema setting is optimized for Digital Cinema content and outputs a picture into HDTV color space. It can be
manually changed to use DCI color space instead.
•
Animation is best to be used with animation or vivid movies.
•
Natural setting for natural hues and tones. Best for dramas and video.
•
Stage setting for live concerts or stage performances.
• 3D setting is to be used dedicated settings for 3D content watched through active glasses compensation.
Additionally, you can define 2 user modes (3 user modes for Inti One only) to finely tune the projector to your video
source and the ambient light.
• User1, User2 and User3 (Inti One only)
The Inti 2 & Inti 3 also have the THX setting to obtain a non over-saturated colors in a dark environment. Optimized
for dark rooms.
Color Profiles (Inti 2 & Inti 3)
Inti 2 & Inti 3 have 12 Color Profile modes, depending on the picture mode, you may choose an available color
profile preset:
•
Standard will bring rich and saturated colors, available with almost any selected Picture Mode.
•
Film1 available with Film Picture Profile, uses the Xenon filter and adjusted to Eastman Kodak film tone
•
Film2 available with Film Picture Profile, uses the Xenon filter and adjusted to Fujifilm film tone.
•
Cinema1 available with Cinema Picture Profile and adjusted to DCI standards
•
Cinema2 available with Cinema Picture Profile and adjusted to HDTV standards.
•
Anime1 best suited to Hollywood animes.
•
Anime2 best suited to Japanese animes.
•
Video color profile is best suited to TV and Sport programs.
•
Vivid color profile is best suited to video games entertainment.
•
Adobe color profile adjusted to Adobe RGB standard.
•
Stage best suited to live concert.
•
3D best with 3D content.
•
Off switches off the color profiles.
Color Temperature
Color temperature stands for the spectral properties of a light source. Low color temperature implies warmer
ambiance (more yellow/red) while high color temperature implies a colder light (more blue). Depending on the
Picture Profile selected, this setting can be set to:
•
Preset: from 5500K / warm colors, up to 9500K / cold colors in steps of 500K.
•
Xenon1 uses the Xenon filter and color compensation to reproduce a film projector
•
Xenon2 uses the Xenon filter and color compensation to reproduce a digital projector
•
Xenon3 same as Xenon2, but within a cooler temperature.
•
High Bright (Inti One only) used for maximum brightness output available.
• Custom1, Custom2 and Custom3 can be used to adjust color temperature to specific environment.
A Custom setting allows a fine adjustment of a Color Temperature by selecting it in the Correction Value menu.
Adjust the Gain values (bright part) and Offset values (dark part) for each color Red, Green and Blue.
Accurate color temperature may require professional tools such as dedicated software and colormeter. Wait
at least 20 minutes after startup before modifying the picture settings.
Gamma
Gamma is the relationship between the color values of the data and the color values displayed. The Gamma
R699800 - Inti Series User Manual
29
6.0 MENU AND PICTURE SETTING
coefficient makes it possible to adjust the brightness of the midtones only without affecting the very bright and very
dark areas. If gamma is set too high, middle tones appear too dark. If it's set too low, middle tones appear too light.
Depending on the current active Picture mode, the Gamma setting can be set to:
•
Normal: Standard tones
•
A (3D): bright picture.
•
B (3D): classic.
•
Film1: Eastman gamma
•
Film2: Fujifilm gamma
•
Film3: more tone than Film1
•
Film4: more contrast than Film2
•
Gamma A: focus on tone
•
Gamma B: for film and movie projection (S curve).
•
Gamma C: for film and movie projection with more detailed blacks than setting B.
•
Gamma D: this setting is recommended for bright midtones and Computer like projection.
•
Custom1
•
Custom2
• Custom3
The Custom data can be set to:
•
Correction Value: a unique value that will act as a gamma coefficient between 1.8 and 2.6.
•
Gamma Adjustment: the gamma curve can be adjusted for each color Red, Green and Blue.
•
Copy: copy the adjusted values to temporal memory.
•
Paste: paste values stored in memory to current profile.
• Reset: reset to the default 2.2 gamma coefficient.
Gamma Adjustment can be copied from all modes. Paste can only be used for Custom modes.
Film Tone (Inti 2 & Inti 3, Film Picture Profile)
It allows 32 fine adjustment steps of the global picture brightness while maintaining the correct contrast level to keep
good black and bright levels. Available when Film Picture profile is selected:
•
White: sets the overall exposure from -16 (under-exposed, darker) up to +16 (over-exposed, brighter)
•
Red/Green/Blue: to set individually each color channel exposure.
Dark / Bright Level
This setting modifies the gamma curve locally in the dark and bright areas.
•
Dark Level from -7 to +7.
•
Bright Level from -7 to +7.
Contrast
The contrast function is used to adjust the contrast between the light and dark areas of the displayed image. A
correct contrast setting is important for good image reproduction. Adjust the Contrast value between -50 and 50.
Brightness
The brightness function is used to adjust the overall light output. Adjust the Brightness value between -50 and 50.
Color
The Color function (or Saturation) is used to adjust the color saturation levels. Adjust the Color value between -50
and 50.
Tint
The hue function is used to adjust the color tint to obtain true color reproduction. Adjust the Tint value between -50
(more red) and 50 (more green).
Advanced
6.2.0.1
Sharpness
Sharpness: this function is used to adjust the image sharpness of the picture. Adjust
the Sharpness value between 0 (soft) and 50 (sharper).
30
R699800 - Inti Series User Manual
6.0 MENU AND PICTURE SETTING
6.2.0.2
Detail Enhancement
Detail Enhancement function is used to improve the picture details to make them
stand out. between 0 (soft) and 50 (strong).
6.2.0.3
Noise Reduction (SD video only)
RNR: Random Noise Reduction. You can set it from 0 up to 16 to reduce the image
random noise.
MNR: Mosquito Noise Reduction function is used to reduce the Mosquito noise on
the picture, generally found in compressed digital video signals such as television
broadcast or encoded movies. Adjust the MNR value from 0 up to 16 to reduce the
typical broadcast picture mosquito noise
BNR: Block Noise Reduction uses a large portion of the picture to reduce the digital
noise, this ensures a higher quality filter. Adjust the BNR value to On or Off.
6.2.0.4
CTI (SD video only)
Color Transition Improvement. Set it to Off, Low, Middle or High to reduce the color
smear (color contour correction). Caution: this function may alter the original picture
chrominance.
6.2.0.5
Color Space (Inti One only)
Standard: Digital Cinema Initiatives (DCI) color space.
Wide1: wider color gamut than standard. Color space used for HDTV.
Wde2: same color space as DCI but within a wider color gamut
6.2.0.6
Color Management (TSL adjustments) (Inti 2 & Inti 3)
The Color Management gives the installer an unique calibration ease with the
integrated Color Adjustment menu: each primary, secondary colors and orange can
be independently calibrated to obtain a precise color balance in a snap.
Adjust the Red, Green, Blue, Yellow, Cyan, Magenta and Orange Tints, Saturations
and Luminances and store them into Custom1, Custom2 or Custom3 profiles.
6.2.0.7
Crystal Motion Drive (120Hz)
The Crystal Motion function uses a 120Hz video processing to render a smooth and
clear motion for movies shot at 24Hz or HD movies at 60Hz. Set the correct level
between:
Mode1: weak black frame insertion
Mode2: strong black frame insertion
Mode3: weak interpolation
Mode4: strong interpolation
Film Motion: inverse telecine interpolation
Additionally, you can set the Clear Motion Demo side-by-side or top-and-bottom.
6.2.0.8
Lens Aperture
The lens is equipped with a variable electronic aperture. This function is used to
optically adjust the light output depending on the viewing conditions and the light
ambiance. Adjust from the correct aperture from partially closed to fully opened.
6.2.0.9
Lamp Power (Inti 2 & Inti 3)
Set the lamp power used by the current Picture Profile:
Normal: lamp is set to 160W
High: lamp is set to 220W.
To avoid any damage to the lamp, you can’t changed the lamp power within 90
seconds from the projector startup or 60 seconds after lamp power change.
Reset
Reset the current Picture Profile to default settings.
6.3
Input Signal menu
HDMI Inputs
This menu is available if the selected active input is HDMI1 or HDMI2.
R699800 - Inti Series User Manual
31
6.0 MENU AND PICTURE SETTING
6.3.0.1
Input
Auto: The input dynamic range is automatically detected and configured.
Standard: Force dynamic range to 16-235.
Enhance: Force dynamic range to 0-255.
Super White: Force dynamic range to 16-255.
6.3.0.2
Check Input Levels
The following pattern is overlaid to current picture to confirm that the correct input
level has been selected.
Use the Input Levels pattern to confirm the correct HDMI dynamic range setting.
6.3.0.3
Color Space
Auto: The source color space is automatically detected and configured.
YCbCr(4:4:4): Set color space to YCbCr 4:4:4.
YCbCr(4:2:2): Set color space to YCbCr 4:2:2.
RGB: Set color space to RGB 4:4:4.
6.3.0.4
Control with HDMI (CEC)
Off: By default the CEC communications are disabled.
On: Enables CEC communications to be sent to the projector through HDMI cable.
CEC: Consumer Electronic Control
6.3.0.5
3D Format
By switching this parameter from the defaut [Auto] setting, this unit will decode any
source on HDMI inputs as a 3D input signal:
Auto: auto selection mode
Frame Packing: decode as frame packing method.
Side by Side: decode as side by side method.
Top & Bottom: decode as top and bottom method.
2D: disable 3D projection.
Component
This menu is available if the selected active input is Component.
•
Y Pb/Cb Pr/Cr: Select this option if the COMP. input is connected to a component video signal.
•
RGB: Select this option if the COMP. input is used with a RGB video source.
PC (Inti 2 & Inti 3)
This menu is available if the selected active input is PC (Sub-D15) input.
•
Auto Alignment: Automatically adjusts Tracking, Phase and Picture Position
•
Tracking: Adjust the horizontal size and display area of the picture.
•
Phase: Adjust flickering and blurred pictures.
•
Picture Position: Adjust the display position of the picture.
Picture Position
Depending on your source, you may find that the picture should be adjusted into the screen, adjust the horizontal
and vertical position of the picture into the screen.
Some signals may not be fully displayed, adjust this setting properly when necessary.
Aspect Ratio
When watching a movie or video program, you can manually set the desired aspect ratio to fill your screen. Select
the correct aspect ratio depending on your source:
6.3.0.1
32
For Video sources
R699800 - Inti Series User Manual
6.0 MENU AND PICTURE SETTING
•
4:3. The original source is considered as 4:3 format. Generally SDTV broadcasts and entertainments.
•
16:9. The picture size is 16:9, generally most recent DVDs, Blu-Ray discs and HDTV broadcasts.
•
Zoom. The zoom function is useful to zoom in the picture and eliminate black bars.
VIDEO SOURCE
ASPECT RATIO
SDTV 4:3
(full frame)
4:3
16:9
Zoom
SDTV 4:3
(with black bands)
4:3
16:9
Zoom
SDTV 4:3
(compatible 16:9)
4:3
16:9
Zoom
NA
4:3
HDTV
(format 16:9)
16:9
NA
4:3
HD signals
AR 2.37 or 2.40
16:9
Aspect Ratio applied to different source formats.
When watching 3D content, only 16:9 aspect ratio is available.
6.3.0.2
For PC sources
•
Auto. Zoom the picture to fill either the screen height or the screen base which ever happens first.
•
1:1 mode, pixel to pixel mapping, no scaling.
•
Full. Stretch the picture full screen.
Sub-D15 or HDMI
ASPECT RATIO
SOURCE
XGA (4:3)
Auto
1:1
Full
SXGA (4:3)
Auto
1:1
Full
1280x768
Full
Auto
1:1
Aspect Ratio applied to PC-signals.
R699800 - Inti Series User Manual
33
6.0 MENU AND PICTURE SETTING
Mask
Depending on your source, you may enable or disable this feature to hide the outer area of the picture. The Mask
function can hide the unexpected scaling artefacts found in broadcast program. You can set it to Off, 2.5% or 5%
globally or for each side of the screen.
Progressive (only 480i, 576i, 1080i)
Interlaced signals are converted to progressive signals using video images from the surrounding. This function is
only available for interlaced input signals: 480i, 576i and 1080i.
6.4
Installation Menu
Lens Control
This menu gives access to the control of the lens. Browse into this menu to adjust:
6.4.0.1
Focus
Adjust the lens focus to obtain a clear picture.
6.4.0.2
Zoom
Adjust the lens zoom to fill the screen with the picture.
6.4.0.3
Shift
Adjust lens shift to center the picture into the screen.
6.4.0.4
Image Pattern
If set to On, an internal pattern will be generated to adjust the current setting. If you
want to use an external generator, turn this option to Off.
6.4.0.5
Lock
Once the Lens is correctly set, you may lock this setting menu by turning the Lens
control Lock to On. Any attempt to access the Lens control menu will lead to the
display of a warning message.
Pixel Adjust
This menu allows a fine adjustment of the red, green and blue panels alignment. Horizontal adjustment moves the
selected color to the right, vertical adjustment moves it up.
•
Horizontal Red (1 to 7)
•
Horizontal Green (1 to 7)
•
Horizontal Blue (1 to 7)
•
Vertical Red (1 to 5)
•
Vertical Green (1 to 5)
•
Vertical Blue (1 to 5)
Installation Style
Flip the image to the left or right, up or down according to the projection state of the projector:
Front, Ceiling Mount (F), Rear or Rear Ceiling mount (R)
Keystone
Compensate for trapezoidal distortion caused by installation. Independently to the screen orientation, make sure
that the projector is not tilt more than 5% left/right and 15% up/down.
•
Vertical Keystone from -30 to +30.
•
Horizontal Keystone from -40 to +40.
Anamorphic (not available with 3D sources)
34
•
Off: No modification to original picture.
•
ModeA: The picture is vertically stretched to fit an installation with anamorphic lens. A cinemascope picture is
R699800 - Inti Series User Manual
6.0 MENU AND PICTURE SETTING
stretched to completely fill the 16:9 panels without black bands, using the optimum resolution and brightness.
ANAMORPHIC
2.35 SOURCE
SDTV (2.35)
HDTV (2.35)
OFF
Mode A
OFF
Mode A
Anamorphic Mode A.
•
ModeB: This setting squeezes horizontally the picture to fit a 16:9 image into cinemascope screen. This setting
is to be used with an anamorphic installation where the lens is permanently fixed in front of the unit and to watch
16:9 content in its original format.
16:9 SOURCE
ANAMORPHIC
SDTV (16:9)
HDTV (16:9)
OFF
Mode B
OFF
Mode B
Anamorphic Mode B.
Screen Adjust
This setting corrects the color balance derived from the reflective characteristics of the screen without altering the
global picture settings. You may select:
Inti One only:
•
Off: no modification.
•
Mode A: slightly reddish.
•
Mode B: slightly greenish.
• Mode C: slightly bluish.
Inti 2 & Inti 3:
•
0 to 95: select the best compensation profile depending on your screen and environment.
•
96 - 99: select a profile between 95 and 99 when watching 3D content with 3D shutter glasses. Profile 99 is
recommended when using Dreamvision’s glasses.
Black Level
Sets the black level when used indoors from 0 to 10.
6.5
Display Setup Menu
Back Color
Configures the screen color displayed when there is no active input. Set to Blue or Black.
Menu Position
Upper left, Upper right, Center, Lower right, Lower left.
Menu Display
15sec: Display menu for 15 seconds before fade out.
On: Always display menu.
R699800 - Inti Series User Manual
35
6.0 MENU AND PICTURE SETTING
Line Display
5sec: Display the input settings for 5 seconds after input selection.
Off: Don’t display.
Source Display
On: Display the source of the input signals after input selection.
Off: Don’t display.
Logo
On: Display logo during startup for 5 seconds.
Off: Don’t display.
Language
Choose the OSD language between: English, Japanese, German, Spanish, Italian, French, Portuguese, Dutch,
Swedish, Norvegian, Russian and Chinese.
6.6
Function Menu
Trigger
The 12V trigger output can be used to control any compatible devices such as motorized screens or anamorphic
kits: The 12V trigger output is 12Vcc, 100mA. Select the trigger output behavior:
•
Off: 12V trigger voltage state is always low.
•
On (Power):12V trigger state is high when the projector is powered ON.
•
On(Anamo): 12V trigger is high only when Anamorphic Mode A or Mode B is engaged. To be used with
anamorphic kits or motorized screens.
Off-Timer
You can configure this automatic power Off function that will switch off the projector when there is no operation or
after a determined timer. Choose the duration of the timer between: Off, 1 hour, 2 hours, 3 hours and 4 hours.
High Altitude Mode
Select this when the projector is in a location of low atmospheric pressure. On or Off.
Communication Terminal (Inti 2 & Inti 3)
Sets on which input is connected the control device. It is not possible to use it at the same time both RS-232C and
LAN inputs. Settings: RS-232C, LAN.
Network (Inti 2 & Inti 3)
When the Communication Terminal selected is LAN, this unit will be visible on the local Network and the following
parameters need to be configured. See “LAN protocole (Inti 2 & Inti 3)”, page 49 for more details.
Lamp Reset
Resets the lamp use time to "0" during the lamp replacement procedure. See “Replacing the Lamp”, page 41 for
more details.
6.7
Information Menu
Input Source
Displays the active video input.
Source
Displays the type of the current video input signal. If PC input is selected, this item cannot be displayed.
Resolution
If the active input is PC input., its resolution is displayed.
H. Frequency
In the case of PC signal, the horizontal frequency is displayed.
V. Frequency
In the case of PC signal, the vertical frequency is displayed.
36
R699800 - Inti Series User Manual
6.0 MENU AND PICTURE SETTING
Deep Color
Display the bit depth (color depth) of the video signals input from the HDMI terminals. Deep Color is not displayed
for YCbCr 4:2:2 signals.
Lamp Time
Displays the accumulated hours of usage of the lamp.
6.8
Expert Calibration (Inti 2 & Inti 3)
Expert Calibration is accessed only by using a programmable IR-RCU, RS-232C or LAN control. Two pairs of
Picture Mode can be activated. Each pair of profiles, similar to Custom1 and Custom2 Picture Modes have to be
calibrated. Once done, these profiles are stored and displayed in the picture mode menu list but will not be
modifiable. See “Available Operating commands”, page 45 for more details.
R699800 - Inti Series User Manual
37
7.0 ANAMORPHIC LENS
7.0 ANAMORPHIC LENS
7.1
Optional 2.35 CineWide and 2.35 THEATRE System (for Inti)
The Inti Series centralizes the controls and automation commands for both the 2.35 CineWide and the 2.35
THEATRE System (for Inti) for a unique, versatile and unexpectedly simple to operate 2.35:1 theatre experience
using an anamorphic Lens.
7.2
•
Integrated Constant Image Width (CIW) scaler for 2D content.
•
Dedicated commands to control the lens position or picture size on a 2.35:1 screen.
Using the Remote Control Unit.
STAND BY
ON
Select active [Input]
INPUT
HDMI 1
HDMI 2
ASPECT
ANAMO
LENS
CONTROL
LENS AP.
COMP.
C.M.D
HIDE
LIGHT
MENU
BACK
Select the correct
[Anamo]rphic Mode
PICTURE MODE
FILM
CINEMA
NATURAL
STAGE
USER1
USER2
GAMMA
COLOR
TEMP
COLOR
P.FILE
ANIME
PIC.
ADJ.
RCU and quick access to anamorphic features
[Anamo]rphic modes
OFF
Anamo Mode A
Anamo Mode B
When you press sequentially the [Anamo]rphic button, you change the mode from OFF, Mode A and Mode B.
38
R699800 - Inti Series User Manual
7.0 ANAMORPHIC LENS
7.3
2.35 CineWide
Video source is 16:9: set [Anamo]rphic to Mode B
When you select a 16:9 input with a permanent anamorphic lens, choose the anamorphic mode B to obtain a
geometrically correct picture in your screen.
•
Select Mode B for this input into the menu “Installation ⇒ Anamorphic ⇒ Mode B”.
Video source is Cinemascope: set [Anamo]rphic to Mode A
When selecting a widescreen input (2.35:1, 2.37:1 or 2.40:1), the original aspect ratio of the source is larger than
16:9, you can see black bars on the top and the bottom of the screen.
•
Select Mode A for this input into the menu “Installation ⇒ Anamorphic ⇒ Mode A”.
Quick [Anamo]rphic mode change on the same input
To obtain the correct aspect ratios, choose Mode A for widescreen movies (format 2.35:1) and Mode B for HDTV
(native format 16:9).
You can also use the Remote Control Unit by pressing the [Anamo] button to switch between these two modes.
Appearance
on 2.35 screen
Mode B
16:9 format
16:9 on 2.35 screen
2.35:1 format
2.35 on 2.35 screen
Mode A
When the source automatically switches format...
... press [Anamo] button to obtain the correct anamorphic mode.
7.4
2.35 THEATRE System (for Inti)
Plug the 12V Trigger output of the projector to the Anamorphic motorization
12V Trigger
to anamorphic
motorization
Connect the 2.35 THEATRE System (for Inti) to the 12V Trigger output
Configure into Function “Menu ⇒ Trigger ⇒ On (Anamo)”
R699800 - Inti Series User Manual
39
7.0 ANAMORPHIC LENS
The “Function ⇒ Trigger” menu determines the 12V Trigger output located in the panel input at the rear of this unit.
This is a global parameter (for all inputs):
•
Off: the 12V Trigger is always switched Off.
•
On (Power): the 12V Trigger is switched On when the projector is running, Off if the projector is in standby Mode.
•
On (Anamo): the Trigger is Off when the anamorphic lens is not needed. It switches to On when the picture is
vertically stretched and when the lens is needed.
Set 12V Trigger to: “Function ⇒ Trigger ⇒ On (Anamo)”.
Video source is 16:9: set [Anamo]rphic to Off
When you select a 16:9 input choose the anamorphic OFF to obtain move the anamorphic lens out. Menu
“Installation ⇒ Anamorphic ⇒ Off”
Video source is Cinemascope: set [Anamo]rphic to Mode A
When selecting a widescreen input (2.35:1, 2.37:1 or 2.40:1), the original aspect ratio of the source is larger than
16:9, you can see black bars on the top and the bottom of the screen.
• Select Anamorphic mode A for this input in the menu Input “Installation ⇒ Anamorphic ⇒ Mode A”.
The Anamorphic Lens is automatically placed in front of the projector to restore the correct picture aspect ratio.
Quick [Anamo]rphic mode change on the same input
If the Trigger setting is set to On (Anamo), the 2.35 THEATRE System (for Inti) is automatically operated when
selecting the correct anamorphic mode.
Appearance
on 2.35 screen
OFF
16:9 format
16:9 on 2.35 screen
2.35:1 format
2.35 on 2.35 screen
Mode A
When the source automatically switches format...
... press [Anamo] button to obtain the correct anamorphic mode.
40
R699800 - Inti Series User Manual
8.0 MAINTENANCE
8.0 MAINTENANCE
8.1
Clean Dirt on the Cabinet
Always use a soft cloth. In case of heavy soiling, soak a cloth in neutral detergent diluted with water, wring dry and
wipe, followed by wiping again using a dry cloth.
Caution
Pay attention to the following as the cabinet may deteriorate in condition, get damaged or paint may come
off.
•
Do not wipe with a stiff cloth.
•
Do not wipe with force.
•
Do not wipe with thinner or benzene.
•
Do not spray volatile chemicals like insecticide.
•
Do not allow prolonged contact with rubber or plastic products.
8.2
Dirt on the Lens
The lens shall be cleaned using commercial blowers or lens cleaning papers (for cleaning glasses and cameras).
Do not use fluid-type cleaning agents. This may lead to peeling of the surface coating film. The lens surface is
fragile. Avoid rubbing it hard or knocking.
8.3
Replacing the Lamp
Light-source Lamp and Lamp Usage Time
The life of light-source lamps used for this unit is about 3000 hours.
•
The lamp life of 3000 hours is merely the average life span of light-source lamps and we do not provide any
guarantee for this figure. The lamp life may not reach 3000 hours depending on the operating conditions.
Deterioration progresses rapidly when the remaining lamp usage time is short. Get ready or replace with a new
lamp when the accumulated usage time exceeds 2900 hours. Depending on the operating conditions, the lamp
may have to be exchanged earlier.
If the image is dark or color tone abnormal, replace the lamp as soon as possible.
• You can also check the accumulated hours of usage. Please refer to Lamp Time in the Information menu.
When the lamp usage time reaches 2900 hours
The Lamp replacement message will be displayed on the screen the next three projection starts.
•
Press the [BACK] button to clear the display.
ABOUT LAMP REPLACEMENT
If this unit is installed in a constricted place, attempting to replace the lamp in that place may cause injury. Move this
unit to a place large enough to perform work.
Use only genuine replacement parts for the lamp unit. Otherwise, malfunction may occur. Also, never attempt to reuse an old lamp unit. This may cause marked performance deterioration or lamp blowout, thus leading to unit
malfunction. Broken pieces of the lamp outside this unit may also cause injuries during lamp unit exchange.
Do not replace the lamp immediately after this unit has been used. The temperature of the lamp is still high and this
may cause a burn. Allow a cooling period of 1 hour or more before replacement.
Before replacing the lamp unit, pull out the power plug from the outlet and wait until the STANDBY/ON led is still light
red. Replacing a lamp with the plug connected to the outlet may cause injuries or electric shocks.
Procedure for Lamp Replacement
During the lamp replacement process, you may have access to sensitive parts of the projector.
R699800 - Inti Series User Manual
41
8.0 MAINTENANCE
•
Loosen the screw on the lamp trap at the rear of this unit.
•
Open the lamp Cover and loosen the 2 screws on the lamp unit to release it.
•
Pull out the lamp unit using the handle.
•
Insert the new lamp unit until it is firmly in place.
•
Tighten the screws of the lamp unit.
•
Attach the lamp cover and fasten the lamp trap screw.
Resetting Lamp Time
After installing a new lamp, reset the lamp time using the OSD menu.
a) Turn On the unit.
b) Browse into the menu Function => Reset Lamp Time.
c) Confirm time reset.
Alternative method in standby mode, using the remote control.
a) Plug this unit to Main power.
b) When the projector is in standby mode (red STANDBY/ON led), use the remote control and press sequentially
the [BACK] - [OK] - [HIDE] within 1 second interval then [DOWN] for at least 2 seconds.
c) The sequence is successful if the STANDBY/ON and LAMP leds blink alternately for 3 seconds.
CAUTION DURING RESET WORK
Reset the lamp time only when you have replaced the lamp.
Never reset it when the lamp is still in use. Otherwise, the approximate standard for gauging replacement time may
be inaccurate, lamp performance may deteriorate and lamp blowout may occur.
8.4
Cleaning and Replacing the Dust Filters
The filters must be cleaned regularly to allow an efficient air intake. Otherwise, dirt may enter the unit and
appear on the screen, preventing you from enjoying the video fully. If dirt has entered the unit or if you need
information about the filter, please consult your authorized dealer. A filter cleaning warning appears every
500 hours.
Cleaning procedure
Pull out the power plug from the outlet while the projector is in standby mode.
Push up and lift the claw of the filters, pull out the filters.
Clean the filters with water and dry them, avoiding direct sunlight. In extremely soiled cases, use of a neutral
detergent is recommended. Insert the filters in their original positions and make sure that the claws are firmly
inserted.
Dust Filters
42
R699800 - Inti Series User Manual
8.0 MAINTENANCE
Clean the Dust Filters every 500 hours.
8.5
Troubleshooting
Warning Messages Led
Operating LED
ID#
Description
STANDBY /
ON
LAMP
orange LED
WARNING
red LED
Blinking
1
red
-
-
-
Unit is in standby mode
2
green
-
-
-
Unit is in operate mode (during projection)
3
blinking
green
-
-
Yes
Unit is in operate mode, but HIDE is ON.
Press again on HIDE button to obtain a
picture.
4
blinking red
-
-
Yes
Unit is in cooldown mode. (switching off)
5/6
-
orange
-
-
Lamp time has reached 2900 hours and/or
prepare to replace the lamp before 3000
hours.
1 time
The lamp failed to ignite, restart the
projector after a complete cooldown cycle.
2 times
Lamp has shut down during projection,
restart the projector after a complete
cooldown cycle.
9
3 times
Lamp cover is open. Check that the lamp
cover is firmly closed and restart the
projector.
10
1 time
Power Supply failed.
11
2 times
Cooling fans stop.
3 times
Internal thermal sensor detects
overheating.
13
4 times
External thermal sensor detects
overheating.
14
1 time
Startup or drive circuits failed
2 times
Communication with drive circuit failed.
16
3 times
Scaler circuit failed
17
4 times
Electrical lens cover failure.
7
8
12
-
-
15
-
blinking
orange
-
blinking
orange
continuous
red
blinking
orange
blinking red
ABOUT WARNINGS AND COOL-DOWN MODE
After projection or when a warning occurred (cases 7-16), the unit will go through a 1 minute cool-down process
known as the Cool Down mode. This function is to prevent lamp breakage and shortened lamp life but also damage
to the internal components of the projector.
The Cool Down mode is indicated by the blinking red STANDBY/ON led. When in Cool Down mode, the projector
cannot be turned ON.
After the Cool Down process is completed, the unit will automatically switch to the Standby mode indicated by a red
STANDBY/ON led.
R699800 - Inti Series User Manual
43
9.0 MISCELLANEOUS
CAUTION
When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air inlets/exhaust vents by
standing the projector on its end or laying it on its side.
9.0 MISCELLANEOUS
9.1
RS-232 protocol
Serial communication specifications
Control of this unit is possible using a computer or automation device connected with a RS-232 cross cable (female
- female D-sub 9 pins cable) or LAN/ RJ-45 cable. Communication specifications for this unit are as follows:
Baud Rate
19200 bps
Data Format
Binary
Mode
Non-Synchronous
Character Length
8 bits
Parity
None
Start Bit
1 bit set to high
Stop Bit
1 bit set to low
X on/off
None
Flow Control
None
RS-232 pin assignation
Pin
Signal
Function
Signal Direction
2
3
5
1,4,6-9
RxD
TxD
GND
N/C
receive data
transmit data
ground
-
PC -> Projector
Projector-> PC
-
1
5
9
6
Command Format
When sending a command to this unit, use the following data format:
44
Header
Unit ID
Command
Data
EoD
1 byte
89h 01h
2 bytes
at least 1 byte
0Ah
Header
(21h): Operating command. PC -> Projector
(3Fh): Reference command. PC -> Projector
(40h): Response command. Projector -> PC
(06h): ACK. Projector -> PC
Unit ID
Fixed to (89 h 01h)
Command
2 bytes. See the list of the available commands below.
If Command code is “52h 43h”, the Data sent may also be sent to the
projector by a programmable RCU using NEC 5 protocole.
Data
1 byte. See the list of the available data for each command below.
EoD
Fixed to (0Ah)
R699800 - Inti Series User Manual
9.0 MISCELLANEOUS
Available Operating commands
Header (21h)
Connection RS-232
Power ON
Command
00h 00h
50h 57h
Data
none
31h
Power OFF
50h 57h
30h
Switch Input
49h 50h
Test Pattern
54h 53h
Gamma
47h 54h
Gamma Value
(Gamma set to
Custom1-3)
47h 50h
32h
33h
36h
37h
2Bh
2Dh
30h
31h
36h
37h
38h
39h
41h
30h
31h
32h
33h
34h
35h
36h
37h
30h
31h
32h
33h
34h
35h
36h
37h
38h
Description
Check the serial connection
If the projector is in stand-by mode, this command
switch the unit ON.
If the projector is powered ON, this command
switches this unit into Stand-by Mode.
Switch active input to Component
Switch active input to VGA
Switch active input to HDMI 1
Switch active input to HDMI 2
Switch to next input
Switch to previous input
Test Patterns Off
Colour bars
Stair Step (black & white)
Stair Step (red)
Stair Step (green)
Stair Step (blue)
Crosshatch (green)
Set Gamma to Normal
Set Gamma to A
Set Gamma to B
Set Gamma to C
Set Gamma to Custom1
Set Gamma to Custom2
Set Gamma to Custom3
Set Gamma to D
Set value to 1.8
Set value to 1.9
Set value to 2.0
Set value to 2.1
Set value to 2.2
Set value to 2.3
Set value to 2.4
Set value to 2.5
Set value to 2.6
RCU Commands and sending them through RS-232
Header (21h)
Power ON
Power OFF
Switch input
Keypad
Command
52h 43h
52h 43h
52h 43h
52h 43h
R699800 - Inti Series User Manual
Data
37h 33h 30h 35h
37h 33h 30h 36h
37h 33h 30h 38h
37h 33h 34h 36h
37h 33h 34h 44h
37h 33h 37h 30h
37h 33h 37h 31h
37h 33h 30h 31h
37h 33h 30h 32h
37h 33h 30h 33h
37h 33h 32h 45h
37h 33h 32h 46h
37h 33h 33h 34h
37h 33h 33h 36h
Description
Switch the unit ON
Switch this unit into Stand-by mode
Switch to next input
Switch active input to VGA
Switch active input to Component
Switch active input to HDMI 1
Switch active input to HDMI 2
UP
DOWN
BACK
MENU
OK
RIGHT
LEFT
45
9.0 MISCELLANEOUS
46
Hide Display
52h 43h
OSD Position
Test Pattern
Picture Mode
52h 43h
52h 43h
52h 43h
Picture Adjust
Gamma
52h 43h
52h 43h
Color Temperature
52h 43h
Color Management
52h 43h
Expert Calibration
(THX)
52h 43h
Expert Calibration
(ISF)
52h 43h
Contrast
52h 43h
Brightness
52h 43h
Color
52h 43h
37h 33h 31h 44h
37h 33h 44h 30h
37h 33h 44h 31h
37h 33h 34h 32h
37h 33h 35h 39h
37h 33h 36h 36h
37h 33h 36h 37h
37h 33h 36h 38h
37h 33h 36h 39h
37h 33h 36h 41h
37h 33h 36h 42h
37h 33h 38h 37h
37h 33h 36h 43h
37h 33h 36h 44h
37h 33h 36h 45h
37h 33h 36h 46h
37h 33h 37h 32h
37h 33h 37h 35h
37h 33h 33h 38h
37h 33h 33h 39h
37h 33h 33h 41h
37h 33h 33h 42h
37h 33h 33h 43h
37h 33h 33h 44h
37h 33h 33h 45h
37h 33h 33h 46h
37h 33h 37h 36h
37h 33h 34h 45h
37h 33h 34h 46h
37h 33h 35h 30h
37h 33h 35h 31h
37h 33h 35h 32h
37h 33h 35h 33h
37h 33h 35h 34h
37h 33h 35h 35h
37h 33h 36h 30h
37h 33h 36h 31h
37h 33h 36h 32h
37h 33h 36h 33h
37h 33h 43h 36h
37h 33h 43h 37h
37h 33h 43h 38h
37h 33h 38h 35h
37h 33h 38h 36h
37h 33h 35h 38h
37h 33h 35h 41h
37h 33h 35h 42h
37h 33h 36h 34h
37h 33h 36h 35h
37h 33h 37h 38h
37h 33h 37h 39h
37h 33h 37h 41h
37h 33h 37h 42h
37h 33h 37h 43h
37h 33h 37h 44h
Toggle Hide ON/OFF
Switch Hide to ON
Switch Hide to OFF
Toggle the OSD position.
Switch Test Patterns
Animation Mode
Stage
Cinema Mode
Film Mode
Natural
Dynamic
3D
User 1
User 2
User 3
THX
Toggle Picture Adj. menu
Toggle Gamma function menu
Set Gamma to Normal
Set Gamma to A
Set Gamma to B
Set Gamma to C
Set Gamma to Custom1
Set Gamma to Custom2
Set Gamma to Custom3
Set Gamma to D
Toggle Color temperature
Set Color Temperature to 5800K
Set Color Temperature to 6500K
Set Color Temperature to 7500K
Set Color Temperature to 9300K
Set Color Temperature to High Bright
Set Color Temperature to Custom1
Set Color Temperature to Custom2
Set Color Temperature to Custom3
Set Color Management to Off
Set Color Management to Custom1
Set Color Management to Custom2
Set Color Management to Custom3
Switch to Adjust mode
THX plus - Off
THX plus - On
Switch Picture Mode to THX - Bright
Switch Picture Mode to THX - Dark
Switch to Adjust Mode.
ISF - Off
ISF - On
Switch Picture Mode to ISF - Day
Switch Picture Mode to ISF - Night
Contrast +
Contrast Brightness +
Brightness Color +
Color -
R699800 - Inti Series User Manual
9.0 MISCELLANEOUS
Tint
52h 43h
Sharpness
52h 43h
Detail Enhancement
52h 43h
CTI
Color Transient Imp
52h 43h
Mosquito Noise
Reduc
52h 43h
Block Noise
Reduc
52h 43h
Random Noise
Reduc
52h 43h
Clear Motion Drive
52h 43h
HDMI CEC
52h 43h
HDMI 3D modes
52h 43h
Aspect Ratio
52h 43h
Anamorphic Modes
52h 43h
Lens Control
Header (21h)
Lens Menu
Lens Shift Up
Lens Shift Down
Lens Shift Right
Lens Shift Left
Lens Focus +
Lens Focus Lens Zoom T
Lens Zoom W
Command
52h 43h
52h 43h
52h 43h
52h 43h
52h 43h
52h 43h
52h 43h
52h 43h
52h 43h
R699800 - Inti Series User Manual
37h 33h 39h 38h
37h 33h 39h 39h
37h 33h 37h 45h
37h 33h 37h 46h
37h 33h 31h 31h
37h 33h 31h 32h
Tint +
Tint Sharpness +
Sharpness Detail +
Detail -
37h 33h 35h 43h
37h 33h 35h 44h
37h 33h 35h 45h
37h 33h 35h 46h
37h 33h 30h 44h
37h 33h 30h 45h
37h 33h 31h 30h
37h 33h 30h 46h
37h 33h 30h 42h
37h 33h 30h 43h
37h 33h 34h 37h
37h 33h 38h 41h
37h 33h 43h 45h
37h 33h 43h 46h
37h 33h 34h 38h
37h 33h 34h 39h
37h 33h 34h 41h
37h 33h 35h 36h
37h 33h 35h 37h
37h 33h 44h 31h
37h 33h 44h 32h
37h 33h 44h 33h
37h 33h 44h 34h
37h 33h 44h 30h
37h 33h 37h 37h
37h 33h 32h 35h
37h 33h 32h 36h
37h 33h 32h 37h
37h 33h 41h 45h
37h 33h 42h 30h
37h 33h 41h 46h
37h 33h 32h 34h
37h 33h 32h 33h
37h 33h 32h 42h
37h 33h 43h 35h
CTI - OFF
CTI- Low
CTI - Middle
CTI - High
MNR +
MNR BNR switch to OFF
BNR switch to ON
RNR +
RNR CMD switch to OFF
Toggle CMD Mode
CMD switch to Mode1
CMD switch to Mode2
CMD switch to Mode3
CMD switch to Mode4
CMD switch to Inverse Telecine
CEC switch to ON
CEC switch to OFF
3D mode set to Auto
3D mode set to frame packing
3D mode set to Side by Side
3D mode set to Top and Bottom
3D mode is disable (force 2D mode)
Toggle Aspect Ratio.
Set Aspect Ratio to 4:3
Set Aspect Ratio to 16:9
Set Aspect Ratio to Zoom.
(PC) Auto
(PC) Full
(PC) Just
Turn OFF the Anamorphic mode
Anamorphic set to Mode A
Anamorphic set to Mode B
Cycle Anamorphic Mode through OFF/A/B
Data
37h 33h 33h 30h
37h 33h 32h 31h
37h 33h 32h 32h
37h 33h 34h 33h
37h 33h 34h 34h
37h 33h 33h 31h
37h 33h 33h 32h
37h 33h 33h 35h
37h 33h 33h 37h
Description
Lens Menu: Toggle the Lens Menu
Shift the picture upward using lens shift
Shift the picture downard using lens shift
Shift the picture to the right using lens shift
Shift the picture to the left using the lens shift
Focus far
Focus near
Zoom Tele
Zoom Wide
47
9.0 MISCELLANEOUS
Lens Aperture
52h 43h
Lens Aperture +
Lens Aperture Lens Cover
52h 43h
52h 43h
52h 43h
Keystone
52h 43h
37h 33h 32h 30h
37h 33h 32h 38h
37h 33h 32h 39h
37h 33h 32h 40h
37h 33h 31h 45h
37h 33h 31h 46h
37h 33h 32h 44h
37h 33h 32h 43h
37h 33h 31h 41h
37h 33h 31h 39h
37h 33h 31h 42h
37h 33h 31h 43h
37h 33h 34h 30h
37h 33h 34h 31h
Toggle the Lens Aperture setting menu
Set Lens Aperture to setting “1”
Set Lens Aperture to settign “2”
Set Lens Aperture to setting “3”
Increase the Lens Aperture value
Decrease the Lens Aperture value
Unsynchronizses Lens Cover with HIDE function
Synchronises Lens Cover with HIDE function
Open Lens Cover
Close Lens Cover
Vertical Keystone +
Vertical Keystone Horizontal Keystone +
Horizontal Keystone -
Examples
You want to...
Command to send
send: 21h 89h 01h 00h 00h 0Ah
Check the connection
receive: 06h 89h 01h 00h 00h 0A
send: 21h 89h 01h 50h 57h 31h 0Ah
Switch the projector ON
receive: 06h 89h 01h 50h 57h 0Ah
send: 21h 89h 01h 50h 57h 30h 0Ah
Switch the projector OFF
receive: 06h 89h 01h 50h 57h 0Ah
Switch the projector OFF with send: 21h 89h 01h 52h 43h 37h 33h 30h 36h 0Ah
OSD confirmation
receive: 06h 89h 01h 52h 43h 0Ah
send: 21h 89h 01h 49h 50h 32h 0Ah
or
Change Active Input to Comp.
send: 21h 89h 01h 52h 43h 37h 33h 34h 44h 0Ah
send: 21h 89h 01h 52h 43h 37h 33h 32h 45h 0Ah
Display On Screen Menu
receive: 06h 89h 01h 52h 43h 0Ah
Available Reference and Response commands
A reference command ask the projector about its status. The projector send back an ACK command together with a
Response command.
Header
Command
Description
Response Data
Power status
50h 57h
Check the Power status.
30h: Standby
(header 3Fh)
31h: Power On
32h: Cool Down
34h: Warning
Active Input
49h 50h
Check which input is active.
30h: S-video
(header 3Fh)
31h: Video
32h: Component
33h: VGA
36h: HDMI 1
37h: HDMI 2
Gamma Table
47h 54h
Check the current Gamma table
30h: Normal
(header 3Fh)
31h: A
32h: B
33h: C
34h: Custom1
35h: Custom2
36h: Custom3
48
R699800 - Inti Series User Manual
9.0 MISCELLANEOUS
Gamma Value
(header 3Fh)
47h 50h
Check the current Gamma value
30h: 1.8
31h: 1.9
32h: 2.0
33h: 2.1
34h: 2.2
35h: 2.3
36h: 2.4
37h: 2.5
38h: 2.6
Examples
You want to...
Command to send
send: 3Fh 89h 01h 50h 57h 0Ah
Check if the projector is switched ON receive: 06h 89h 01h 50h 57h 0Ah (confirm cmd)
receive: 40h 89h 01h 50h 57h 31h 0Ah (projector is ON)
send: 3Fh 89h 01h 49h 50h 0Ah
receive: 06h 89h 01h 49h 50h 0Ah (confirm cmd)
Which input is active
receive: 40h 89h 01h 49h 50h 36h 0Ah (HDMI 1 is active)
9.2
LAN protocole (Inti 2 & Inti 3)
LAN / RJ-45 communication specification
To set the projector to LAN Control Mode, go to the Function menu, then set the Communication Terminal from RS232C (default) to LAN.
The network settings may have to be modified in the projector’s network menu to match your current LAN network.
•
DHCP Client: When set to ON, the projector’s IP address will be automatically set by the DHCP server. on the
LAN.
•
IP Address: Sets the IP (Internet Protocol) address of the projector. A valid address must be set for this unit.
•
Subnet Mask: Sets the Subnet Mask
•
Default Gateway: Sets the Default IP Gateway of the projector.
•
MAC Address: A 6 byte hex number that uniquely identifies the projector on the LAN. The value is unique to
each individual unit on the LAN network.
The first step to verify that the network configuration of this unit has been correctly set is to ping the projector from a
computer on the network using the command prompt.
R699800 - Inti Series User Manual
49
9.0 MISCELLANEOUS
Sending a LAN Control Command
In order to send a Remote Control compatible command to this unit, you must open a TCP connection on port
20554. and send a command immediately as the connection will be dropped within 5 sec of inactivity..
Control Device
Projector
1. Openning Connection
on port 20554
2. Projector Ready
(PJ_OK)
3. Command Type
(PJREQ)
4.Projector Acknoledge
(PJACK)
5. Command
6. Projector confirms
After 5sec, connection
is closed.
LAN communication protocol and timed out
Examples
You want to...
Switch the projector ON
Switch Anamorphic to mode A
9.3
Command to send
1. open TCP connection
2. receive PJ_OK : 50h 4Ah 5Fh 4Fh 4Bh
3. send PJREQ: 50h 4Ah 52h 45h 51h
4. receive PJACK: 50h 4Ah 41h 43h 4Bh
5. send Power On cmd: 21h 89h 01h 52h 43h 37h 33h 30h 35h 0Ah
6. receive confirmation: 06h 89h 01h 52h 43h 0Ah
after 5 sec, TCP connection is closed.
1. open TCP connection
2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh
3. send PJREQ: 50h 4Ah 52h 45h 51h
4. receive PJACK: 50h 4Ah 41h 43h 4Bh
5. send Anamorphic A: 21h 89h 01h 52h 43h 37h 33h 32h 33h 0Ah
6. receive confirmation: 06h 89h 01h 52h 43h 0Ah
after 5 sec, TCP connection is closed.
Infra Red, long hex-pronto compatible RCU
The infra red command must be sent using NEC 5 protocol in ASCII format.
In the following example, Power ON command is 37h 33h 30h 35h, this command has to be converted as ASCII, it
becomes 73 05.
To send this command using long hex Pronto compatible, convert the ASCII code as two hexadecimal numbers as
follow:
73h = 115
05h = 5
Then program the Pronto RCU using the Device number 115 and Function 5:
Device Code: 115 (0x73) Function: 5 (0x05):
0000 006D 0001 0011 0141 00A0 0014 003C 0014 003C 0014 0014 0014 0014 0014 003C 0014 003C 0014 003C
0014 0014 0014 003C 0014 0014 0014 003C 0014 0014 0014 0014 0014 0014 0014 0014 0014 0014 0014 0336
A complete device/function chart with their corresponding long hex commands is available, ask your dealer if
required.
50
R699800 - Inti Series User Manual
9.0 MISCELLANEOUS
9.4
PC compatible signals
On HDMI Inputs
Designation
VGA 60
VGA 59.94
SVGA 60
XGA 60
WXGA 60
WXGA+ 60
SXGA 60
WSXGA+ 60
WUXGA 60
Resolution
640 x 480
640 x 480
800 x 600
1024 x 768
1280 x 768
1440 x 900
1280 x 1024
1680 x 1050
1920 x 1200
fh (kHz)
31.500
31.469
37.879
48.363
47.760
55.919
63.981
65.222
74.038
fv (Hz)
60.000
59.940
60.317
60.004
60.000
59.999
60.020
60.002
59.950
Dot (MHz)
25.200
25.175
40.000
65.000
79.998
106.470
108.000
147.140
154.000
Polarity
H- VH- VH+ V+
H- VH- V+
H- V+
H+ V+
H- V+
H+ V-
Total dots x lines
800 x 525
800 x 525
1056 x 628
1344 x 806
1675 x 796
1904 x 932
1688 x 1066
2256 x 1087
2080 x 1235
fh (kHz)
31.500
37.900
37.500
43.300
37.900
48.100
46.900
53.700
48.400
56.500
60.023
68.700
47.760
55.919
63.981
64.740
65.222
67.500
35.000
49.107
60.241
fv (Hz)
60.000
72.000
75.000
85.000
60.000
72.000
75.000
85.000
60.000
70.000
75.029
85.000
60.000
59.999
60.020
59.950
60.002
60.000
66.667
75.087
74.927
Dot (MHz)
25.175
31.500
31.500
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
79.998
106.470
108.000
101.000
147.140
148.500
30.240
55.000
80.000
Polarity
H- VH- VH- VH- VH+ V+
H+ V+
H+ V+
H+ V+
H- VH- VH+ V+
H+ V+
H- V+
H- VH+ V+
H+ V+
H- VH+ V+
H- VH- VH- V-
Total dots x lines
800 x 525
832 x 520
840 x 500
832 x 509
1056 x 628
1040 x 666
1056 x 625
1048 x 631
1344 x 806
1328 x 806
1312 x 800
1376 x 808
1675 x 796
1904 x 932
1688 x 1066
1560 x 1080
2256 x 1087
2200 x 1125
864 x 525
1120 x 654
1328 x 804
On Sub-D15 (VGA) input
Designation
VGA 60
VGA 72
VGA 75
VGA 85
SVGA 60
SVGA 72
SVGA 75
SVGA 85
XGA 60
XGA 70
XGA 75
XGA 85
WXGA 60
WXGA+ 60
SXGA 60
SXGA+ 60
WSXGA+ 60
1920 x 1080 60
MAC 13”
MAC 16”
MAC 19”
Resolution
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 768
1440 x 900
1280 x 1024
1400 x 1050
1680 x 1050
1920 x 1080
640 x 480
832 x 624
1024 x 768
R699800 - Inti Series User Manual
51
9.0 MISCELLANEOUS
9.5
Specifications
Overview
The Inti Series uses the latest technology developed to provide the ultimate video-projection experience. LCoS
(Liquid Crystal on Silicon) technology based on a reflective principle features an extremely high-definition picture
and seamless color gradations.
Emission Method
Display Panel/Size
Native Resolution
Contrast Ratio
Projection Lens
Brightness
Screen Size
Distance range
Input Signals
Component Input
VGA (Sub-D15)
(not on Inti One
only)
HDMI 1 Input
HDMI 2 Input
Color Management
Video processing
Input Sync Frequency
Analog Inputs
Digital Inputs
Light-source Lamp
Power Requirements
Power Consumption
Dimensions
(Width x Height x Depth)
Net Weight
LCoS (Reflective Active Matrix Principle)
0.7" LCoS panel
3x 1920 x 1080 pixels
50,000:1 (Inti One only) with 3 screen modes
70,000:1 & 100,000:1 (Inti 2 & Inti 3) with 99 screen modes and dynamic lamp
power adjustment.
Throw Ratio 1.4:1 - 2.8:1 with 2.0x Zoom
Electronic zoom, focus et shift
Electronic aperture control (16-steps Aperture)
Automatic Lens Cover
1300 ANSI Lumens
60" to 250" (Aspect ratio 16:9)
from 1,50m to 12 m
(YPbPr) 480i/p, 576i/p, 720p50/60, 1080i50/60 (suppport R/G/B Sync on G)
VGA@60-85Hz, SVGA@56-85Hz, XGA@60-85Hz, SXGA@60Hz,
WSXGA@60Hz, 1920x1080@60Hz(H+V+)
480i/p, 576i/p, 720p50/60, 1080i50/60, 1080p24/50/60
VGA@60Hz, SVGA@60Hz, XGA@60Hz, WXGA@60Hz, SXGA@60Hz,
WSXGA@60Hz,WUXGA@60Hz
3D compatible with Blu-ray, side-by-side and top-and-bottom
480i/p, 576i/p, 720p50/60, 1080i50/60, 1080p24/50/60
VGA@60Hz, SVGA@60Hz, XGA@60Hz, WXGA@60Hz, SXGA@60Hz,
WSXGA@60Hz,WUXGA@60Hz
3D compatible with Blu-ray, side-by-side and top-and-bottom
Advanced color settings (7-axis: primaries, secondaries and orange)
Detail Enhancement, Sharpness, DNR, MNR, BNR
74.5 Mhz
150 Mhz
220 W Ultra-high pressure mercury lamp
AC 110 V - 240 V AC, 50 Hz/60 Hz
<350W, 3.5A (0.9W in standby mode)
(Excluding feet)
455 x 215 x 505 mm - 17.9" x 8.5" x 19.9"
approx. 15,2 Kg - 33.5 lbs
•
Design and specifications are subject to change without prior notice.
•
Please note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in
order to aid comprehension. Images may differ from the actual product.
3-CHIP LCOS SYSTEM
LCoS is the abbreviation of Liquid Crystal on Silicon. The 3-Chip LCoS systems feature dedicated panels for each
color channel and render seamless color graduations without any flickering or rainbow effect artifacts.
52
R699800 - Inti Series User Manual
9.0 MISCELLANEOUS
Dimensions
455 mm
505 mm
17.9’’
19.9’’
19.9’’
505 mm
215 mm
8.5’’
455 mm
17.9’’
Contact Information:
TEC - Dreamvision
7, rue La CAILLE, 75017 Paris - FRANCE
Web: www.dreamvision.net
R699800 - Inti Series User Manual
53
9.0 MISCELLANEOUS
54
R699800 - Inti Series User Manual