KCM-8111
2M Indoor PTZ with D/N, Advanced WDR,
SLLS, 18x Zoom lens
(DC 12V / High PoE)
Ver. 2012/11/23
KCM-8111 Hardware User’s Manual
Table of Contents
0.
Precautions
3
1.
Introduction
4
Package Contents ........................................................................... 4
Features and Benefits ..................................................................... 5
Safety Instructions .......................................................................... 6
Physical description ........................................................................ 8
Product Specification .................................................................... 11
2.
Accessing Camera
13
If you have DHCP server / router in your network: ...................... 13
If you do NOT have DHCP server / router in your network: ......... 13
2
www.acti.com
KCM-8111 Hardware User’s Manual
0. Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to
follow the safety instruction given may directly endanger people, cause damage to the system
or to other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the users will be required to correct the
interference at their own expense.
3
www.acti.com
KCM-8111 Hardware User’s Manual
1. Introduction
Package Contents
KCM-8111
QIG
Terminal Blocks for Power and DI/O
Surface Mount Kit
Accessories
Warranty Card
4
www.acti.com
KCM-8111 Hardware User’s Manual
Features and Benefits
This is a cutting edge network video surveillance camera. It can capture, compress and
transmit real time video in excellent quality (15 FPS 2 Megapixel, 1920 x 1080). This camera is
your best choice to build an intelligent IP surveillance system.
Adaptive Profile
With the innovative embedded Image Signal Processor (ISP), this camera responds to
changing lighting condition with customized algorithm. This allows for clear image with very
little noise at night.
H.264/MPEG-4/MJPEG Triple Codec Dual Streaming
This device supports 3 compression formats, H.264, MPEG-4 and MJPEG. It brings superior
image quality at 15 frames per second in Full HD 1080p (1920 x 1080). In 720p (1280 x 720)
and VGA resolution (640 x 480) the device reaches 30 frames per second.
Advanced WDR
Advanced WDR technology is the most advanced approach of improving the dynamic range of
the camera. While many other WDR technologies enhance the dynamic range while producing
noise, blur edges of objects and untrue colors, Advanced WDR is designed to improve the
dynamic range while keeping the true colors, sharp edges of objects and free from noise.
Powerful Bundled Surveillance Software
To extend the capabilities of the IP PTZ Camera series, a powerful surveillance program is
included in the package for free. Users can easily use an existing PC as a digital video recorder.
Scheduled recording and manual recording keep every important video recorded in the local
hard disk. Reliable and accurate motion detection with instant warning enables immediate
response in every condition. Quick and simple search and playback function lets you easily find
the images and video you want.
Software Development Kit Support
This IP PTZ Camera can be integrated or controlled by applications from third party software
developers. Software developers can save considerable efforts by using our Streaming Library
or ActiveX control.
5
www.acti.com
KCM-8111 Hardware User’s Manual
Safety Instructions
Don’t use the power supply with other voltages
This device is likely to be damaged or damage other equipments / personnel, if you use a
power supply with different voltage than the one included with this device. All warranty of this
product will be voided in the situations above.
Don’t open the housing of the product
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device and the power supply in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to
qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in
6
www.acti.com
KCM-8111 Hardware User’s Manual
this manual. Adjust only those controls that are covered by the instruction manual, as an
improper adjustment of other controls may result in damage, and will often require
extensive work by a qualified technician to restore the video product to its normal
operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
7
www.acti.com
KCM-8111 Hardware User’s Manual
Physical description
1) Digital Input / Output
Used in applications like motion detection, event triggering, time lapse recording, alarm
notifications, etc., the I/O terminal connector provides the interface to:
-2 transistor output - For connecting external devices such as relays and LEDs. Connected
devices can be activated by Output buttons on the Live View page or through video
management software. Connect Pin 2 with 4 or 6 with 8.
-2 Digital Input - An alarm input for connecting devices that can toggle between an open and
closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. The device
will detect the change in digital input and transmit the signal to video surveillance servers.
Pin 1
GND
Ground. Connect with Pin 3 for DI control loop.
Pin 2
12V
Provides power to external devices with a
Voltage: 12V DC,
maximum current of 100mA.
Max: 1.2W
Connect to GND to activate, or leave floating
Must not be exposed
(or unconnected) to deactivate.
to voltages greater
Pin 3
Digital Input
than 30V DC.
Pin 4
Transistor
Connect to Pin 2 through external devices for
Max load = <100mA
Output
DO loop. If used with an external relay, a diode
Max voltage = 24V DC
must be connected in parallel with the load for
(to the transistor)
protection against transient voltages.
8
www.acti.com
KCM-8111 Hardware User’s Manual
(Pin 5 – 8 repeats Pin 1-4 for another set of DIO)
Connect input/output devices to the camera as follows:
1. Attach the cables for the device securely to the supplied green connector block.
2. Once cables are connected, push connector block into the terminal connector on camera.
2) Audio Input / Output
The IP device supports audio input and output via 3.5mm phone jack.
3) DC 12V Power Input
Connect DC power source to the terminal block. The wire with white dashed lines is the live
wire, which should connect to the 12V pin.
4) Ethernet Port
The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this
IP device can auto detect the speed of local network segment (10Base-T/100Base-TX
Ethernet).
5) Micro SD / Micro SDHC Card Slot
Insert your Micro SD card here for local recording on camera
9
www.acti.com
KCM-8111 Hardware User’s Manual
1) Power Button
Press the Power Button and then camera will reboot automatically.
2) Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.)
Step 3: Reconnect the power cable while continuing to hold the reset button. The red
Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for
another second and turn off again. By this time the reset to default operation is already
completed. This will take around 20 seconds from power up. You may then release the
reset button. This length of time fluctuates slightly with the environment. The Power LED light
will come back on and stay on after a few more seconds. The unit will start up with factory
default settings automatically.
Restore to Default
Complete
Power On
On (3s)
On
1s
Off (about 15s)
Off (10~15s)
Stay On
About 20 Seconds
10
www.acti.com
KCM-8111 Hardware User’s Manual
Product Specification
KCM-8111
• Device
Device Type
Image Sensor
Day / Night
Minimum Illumination
Color to B/W switch
Mechanical IR Cut Filter
IR Sensitivity Range
IR LED
Electronic Shutter
Indoor PTZ Camera
Progressive Scan CMOS
Yes
Color: 0.1 lux at F1.6 (30 IRE, 2400 °K); B/W: 0.05 lux at F1.6
ISP based switch, configurable
Yes
700 - 1100 mm
No
1/25 - 1/2000 sec (50Hz); 1/15 - 1/2000 sec (60Hz) (manual mode); 1- 1/2000 sec (auto mode)
• Lens
Focal Length
Iris
Focus
Horizontal Viewing Angle
Zoom, f4.7 - 84.6 mm / F1.6 - 2.8
DC Iris
Auto Focus
48.94° ~ 3.61°
• PTZ
Zoom Ratio
Zoom Speed
Manual Panning Speed
Manual Tilting Speed
Preset Panning Speed
Preset Tilting Speed
Panning Range
Tilting Range
Control
Preset Panning Accuracy
Preset Tilting Accuracy
Absolute Positon
Protocol
18x optical
2 sec (1x ~18x)
0.5° ~ 90°/S
0.5° ~ 90°/S
0.5° ~ 450°/S
0.5° ~ 450°/S
350° (360° pan via Auto-flip)
0°~180°
Remote manual control; 64 preset point; 10 preset tours
0.265°
0.265°
Yes
Sony VISCA, Pelco D
• Video
Compression
H.264, MPEG-4 SP, MJPEG
Maximum Frame Rate
15 fps at 1920 x 1080 (Full HD 1080p) ; 30 fps at 1280 x 720 (HD 720p) ; 30 fps at 640 x 480 (VGA)
vs. Resolution (H.264, MJPEG)
Maximum Frame Rate
vs. Resolution (MPEG-4 SP)
Multi-Streaming
Bit Rate
Bit Rate Mode
Image Enhancement
10 fps at 1920 x 1080 (Full HD 1080p); 24 fps at 1280 x 720 (HD 720p) ; 30 fps at 640 x 480 (VGA)
Simultaneous dual steams based on two configurations
28 Kbps - 6 Mbps (per stream)
Constant, Variable
Advanced WDR; White balance: automatic, hold and manual; Brightness; Saturation;
Contrast; Sharpness; Automatic gain control; 2D+3D Digital Noise Reduction; Flickerless; Defogging
Text Overlay
Image Orientation
• Audio
Audio
Compression
Audio-In
Audio-Out
• Network
Protocol & Service
Ethernet Port
Security
User defined text on video
Image flip and mirror
2-way
8 kHz, Mono, PCM, 16 bit encoding; G.711
3.5mm Phone Jack
3.5mm Phone Jack
TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, IPv6, DNS, DDNS, NTP, ICMP, ARP, IGMP,
SMTP, FTP, UPnP, Bonjour
1, Ethernet (10/100 Base-T), RJ-45 connector
IP address filtering; HTTPS encryption; Password protected user levels; IEEE 802.1X network access
control
11
www.acti.com
KCM-8111 Hardware User’s Manual
• Alarm
Alarm Trigger
Alarm Response
• Interface
Digital Input
Digital Output
Local Storage
• General
Power Source / Consumption
Weight
Dimensions (Φ x H)
Bundled Accessories
Environmental Casing
Mount Type
Operating Temperature
Operating Humidity
Approvals
• Integration
Unified Solution
ISV Integration
Firmware Access Browser
Video motion detection (3 regions); External device through digital input
Notify control center; Go to PTZ preset point or preset tour; Change camera settings; Command other
devices; E-mail notification with snapshots;
Save video or snapshot to local storage; Upload video, snapshot to FTP server; Activate external
device through digital output
2, terminal block
2, terminal block
MicroSDHC memory card slot (card not included)
High PoE (IEEE802.3at) / 19.2 W
DC 12V / 15W
126 mm x 163 mm (5" x 6.4")
126 mm x 163 mm (5" x 6.4")
Power Adapter
Transparent dome cover
Surface, Flush, Pendant, Wall, Corner, Pole
-10 °C ~ 50 °C ( -14 °F ~ 122 °F)
10% ~ 85% RH
Camera: CE, FCC
Adapter: CE, FCC, UL, PSE, EFFICIENCY LEVEL V
Fully compatible with ACTi software
Software Development Kit (SDK) available
Microsoft Internet Explorer 6.0 or newer
12
www.acti.com
KCM-8111 Hardware User’s Manual
2. Accessing Camera
If you have DHCP server / router in your network:
Many network server / routers are able to automatically provide IP addresses through DHCP. If
you are using such a network, just plug in your computer and IP PTZ Cam into the network and
your IP device will acquire network address by itself. Find and access the device with our IP
Utility program. You may download it at:
http://www.acti.com/product/detail/Software/ACTi_Utility_Suite
If you do NOT have DHCP server / router in your
network:
1. Configure your PC to use the same subnet by changing your PC’s IP address to the
subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254
except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.
2. The default IP used by this device is 192.168.0.100. Please make sure your PC is
NOT using this address and that no two equipments use the same IP address in
the network.
3. Change your IP address by going to Control Panel ->Manage Network Connections ->
Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.
Please set the settings as below.


IP address: 192.168. 0.xxx

Subnet mask: 255.255.255.
0
(NOTE: xxx should be a number
from 1 to 254 except 100, which is
used by the IP device. Please also
make sure that no two equipments
use the same IP address in the
same network..)
13
www.acti.com
KCM-8111 Hardware User’s Manual
4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:
192.168.0.100
5. When you see the login window, please input default user and password:
Default User: Admin
Password: 123456
6. After logging in, you will see the video from camera. To go to the main menu, click
the ”Setup” button on the top left.
14
www.acti.com
KCM-8111 Hardware User’s Manual
If you are using a single camera, this is enough to access the device.
If you are using multiple devices, you need to change the current device to another
unused IP address, so that when the next device is connected to the network, no two
devices use the same IP. Please perform the following steps.
7. Go to Network -> Connection Type
8. Change the IP mode to Static.
9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP
address or 192.168.0.100.). If this is not the first device you add to the network, please
also avoid other devices’ IPs.
10. Click “Apply”
11. Please go to Maintain -> Save & Reboot, and click ”Apply”. Internet Explorer will close
after a few seconds. This is normal.
12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example,
192.168.0.101). For the second device or more you add into the network, please type
the correct IP.
13. Adjust the default Video setting by going to Video & Audio ->Video
15
www.acti.com