SEM 1201P Specifications

Security Engineered Machinery Co., Inc.
OPERATIONAL & MAINTENANCE MANUAL
SEM Model 1201P
Shredder
As of April 1, 2009
Security Engineered Machinery Co., Inc.
NATIONWIDE SERVICE
Phone Toll Free: 1(800) 225-9293
Email: Service@SEMSHRED.com
Fax: 1(508)366-6814
Website: WWW.SEMSHRED.com
FORWORD
This manual provides the operation procedures for the paper shredder Model 1201P.
Please read this manual thoroughly before starting up the shredder. Keep this manual
handy so that you can refer to it at any time.
The signal words “Warning” and “Caution” found in this manual and on warning labels
affixed to the shredder correspond to the degree of injury that may result.
! Warning
Indicates a potentially hazardous situation, if not
avoided, could result in serious injury.
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate
injury. It is also used to alert against property
damage.
In addition to the signal words mentioned above, the following two symbols are used to
indicate the prohibited actions and to highlight the important actions.
<Example>
Indicates prohibited actions. Example means “do not
dismantle the product”.
Indicates mandatory actions or restricted actions. Example
means “pull out the power plug”.
DO NOT USE SHREDDER FOR ANY OTHER PURPOSE
THAN DESCRIBED IN THIS MANUAL.
For NATIONWIDE SERVICE call 1(800)225-9293
2
TABLE OF CONTENTS
Intended Use and Safety Precautions...……………………………………………………4
Specifications……………………………………………………………………….……..7
Parts Identification………………………………………………………………………...8
Safety Functions…………………………………………………………………….……10
Installations…………………………………………………………………………..…..12
Operating Procedures……………………………………………………………….........13
Troubleshooting………………………………………………………………………….17
Daily Maintenance…………………………………………………………………….....19
Parts List……………………………………………………………………………...20-36
For NATIONWIDE SERVICE call 1(800)225-9293
3
Intended Use
This paper shredder is exclusively designed for destroying paper documents only.
SAFETY PRECAUTIONS
!
WARNING
Keep out of reach of children, sharp cutters inside may cause injury.
Do not allow children to use the shredder and do not use it within
children’s reach. If they touch the shredder, injury, burn and/or electric
shock may result.
Do not use the shredder with any other voltage than specified in this
manual. Do not overload the receptacles by plugging too many leads into a
single socket. It may cause a fire or electric shock.
Do not remove the covers, cases or cabinets. Sharp cutters inside may
cause injury.
Do not damage, break or deform the power cord. Do not place heavy
objects on it, pull it or bend it forcedly. Damage power cord may cause a
fire or electric shock.
Do not modify the shredder; it may cause a fire or electric shock.
Stop using the shredder immediately when smoke is emitted, unusual
smell comes out and /or abnormal heat is generated. Turn off the power
switch and pull out the power plug. Then contact us at 800-225-9293. Do
not use it continuously a fire or electric shock may result.
If shredder comes in contact with any foreign material such as a metal,
For NATIONWIDE SERVICE call 1(800)225-9293
4
water or any liquid, immediately turn off power switch and pull out the
power plug. Then contact us at 800-225-9293
SAFETY PRECAUTIONS Cont….
Do not plug in or unplug the power cord with wet hands, electric shock
may result.
Do not carry out any maintenance or services other than the ones
mentioned in this manual. Opening or removal of covers will expose you
to dangerous moving parts, therefore may cause serious injury.
CAUTION
Do not insert hands or other objects into the throat opening, sharp cutters
inside may cause serious injury.
Do not hold paper near the feed opening with your hands and do not push
paper into it. The pulling force of the motor is very strong and hands may
get pulled in and seriously injured.
Keep all loose articles of clothing, long hair, ties, scarves, necklaces,
bracelets etc away from the feed opening. Injury may result if such items
are drawn in press the “STOP” button immediately.
Do not insert any article other than paper. Do not shred carbon paper, wet
paper, glue backed paper, stickers, self-adhesive envelopes, DHL/FEDEX
labels, security tape, adhesive tape, OHP films, magnet sheets, plastic bags
and clothes attention.
For NATIONWIDE SERVICE call 1(800)225-9293
5
tilted
Do not, place shredder, on an unstable area such as an uneven floor or
stand injury may result if it falls.
SAFETY PRECAUTIONS Cont….
Do not install the shredder in humid or dusty place. Keep water away from
the shredder if water splashes on it fire or electrical shock may result.
Always pull out the plug before moving the shredder. If the power cord is
damaged a fire or electric shock may result.
Turn off the breaker after using the shredder. If it is not used for a long
period of time pull out the power plug. If it is plugged for a long time it
may cause a fire.
Do not pull the power cord when pulling out the plug. I the cord is
damaged a fire may result.
Do not place any heavy object on the shredder if it falls injury may result.
For NATIONWIDE SERVICE call 1(800)225-9293
6
SPECIFICATIONS
MODEL
Feed opening/loading width
Shred Size
Cutting Type
Rated Sheet Capacity
Cutting Speed
Input Voltage
Rated Power Consumption
Stand-by Power Consumption
Dimensions
Weight
Other
1201P
12.40” (315 mm)
Approximately 0.24” x 0.56”
Cross Confetti Cut
Letter size copy paper (20lb)
Approximately 22 sheets Maximum 45
sheets
Approximately 2.2 – 10.45 yard / min
120V AC / 8.0A (Max. 14A) / 60 Hz
720 W
0 W (5 min. after operation)
20” x 20” x 34”
Approximately 191.4 lbs
Super potential power unit (variable speed
control)
No power consumption during stand-by
Paper jam prevention mechanism
LCD display with backlight
Automatic start/stop, Automatic power cutoff
Overflow stop, Auto reverse, Auto cut
Cabinet door switch
Circuit breaker (used as power switch)
Safety beep, Error message, Caster
For NATIONWIDE SERVICE call 1(800)225-9293
7
PARTS IDENTIFICATION
NAME
(1) Throat Opening
(2) Operation keys and display
(3) Breaker used as Main switch
(4) Cabinet Door
(5) Waste Basket
(6) Casters
FUNCTION
Paper to be shredded is fed through here
See Page 8
Used as the main ON/OFF switch. It works
in case of circuit failure or motor lock in
order to protect the motor from burnout.
Opened to take out/put in the waste basket
Shredded particles are stored here
Used to move the shredder, Front casters
have stoppers which should be locked at
the installation place.
For NATIONWIDE SERVICE call 1(800)225-9293
8
OPERATION KEYS AND DISPLAY
NAME
(1) Liquid Crystal Display
(2) STOP key
(3) START key (shredder)
(4) REVERSE key
FUNCTION
Current status is displayed
Stops shredding and paper feeding
Pressing the upper side of this key after
turning on the breaker or during power
saving mode makes shredder ready for
operation
Cutting block runs in reverse while this key
is pressed
For NATIONWIDE SERVICE call 1(800)225-9293
9
SAFETY FUNCTIONS
Safety Devices
(1) Auto-cut (Motor overheating protection)
When motor is locked or overloaded for a certain period of
time the motor overheat protection is activated to cut off
the motor power. When activated a beep sounds and the
machine will stop. When motor is cooled the machine will
reset automatically and the alarm beeps again.
(2) Cabinet Door Switch
Prevents the shredder from operating while cabinet door is open.
(3) Overflow Stop
When the waste basket becomes full the shredder
automatically stops after leveling shredded material.
(4) Auto Reverse
When exceeding the maximum sheet capacity the
shredder may get jammed the shredder will stop and then
reverses automatically so that the jammed paper can be
removed. Pressing the REVERSE key also activates the
reverse operation.
(5) Circuit Breaker
To protect against circuit failure the motor is locked for a certain period of time, this
feature will protect the motor wiring from burnout and overload.
(6) Feed Opening Switch
The feed opening switch prevents the shredder from operating while the jammed
paper is being removed through its enlarged feed opening this operation uses the auto
reverse function.
For NATIONWIDE SERVICE call 1(800)225-9293
10
SAFETY FUNCTIONS Cont…
Alarm and Beep
(1) Acceptance Beep
It sounds on acceptance of key entry and when the machine status changes
(2) Alarm
Shred Runs by Start Key Press
The beep sounds intermittently every 5 seconds when paper or foreign articles are
detected near the feed opening while the shredder stops and the screen shown above is
displayed.
Note: If this status lasts for more than 3 minutes, the machine locks up
temporarily and Error 1 is displayed.
(3) Status Information Beep
In the following occasions, the information beep sounds to notify the status
change.
When the shredder starts evening out the waste chips
After detecting that the waste basket is full.
When the auto-cut function is activated and when the
machine restores itself.
When an error is generated;
Note: for details of errors refer to pages 22-23
For NATIONWIDE SERVICE call 1(800)225-9293
11
INSTALLATIONS
™ Place the shredder near the power outlet in such a way that the power plug is
easily accessible.
Note1: Do not install the shredder near heat sources such as radiator, flammable
liquids or gases.
Note 2: Do not install the shredder on uneven or unstable floor.
™ Lock the front two casters.
Note: Before moving the shredder, make sure that the locks of front two casters
are released.
™ Insert the plug into the outlet which means the specifications on the nameplates
(i.e. 120V ac, 15 Amps).
Make sure that no other equipment uses the same outlet.
™ Attach a plastic bag firmly to the waste basket so that you can change the bag
without scattering paper chips.
Note: Make sure to remove the air between the plastic bag and the basket. If not it
may cause a malfunction of the sensor detecting waste volume level.
For NATIONWIDE SERVICE call 1(800)225-9293
12
OPERATING PROCEDURES
Automatic Operation
Procedure
Turn on the breaker and press
the upper part of START key of
the shredder. The SHRED
READY screen appears.
Note: If idle for more than 5
minutes it goes into the power
save mode and all power goes
off. Press the upper part of the
START key again to restore.
Feed the paper straight forward
into the throat opening by
aligning the center part to the
AUTO START mark. When paper is
drawing into the shredder,
remove your hands
immediately.
Display
Shredding volume is displayed
in 4 levels as shown in the right.
● It is recommended to
shred the paper
with the volume of (a) to
(c) levels.
● If the paper to be shredded
exceeds the level (d), autoreverse function may work.
Note: Shred levels vary depending
on the paper
quality and/or voltage
fluctuation, so take
these levels as a reference.
After using the shredder, turn
OFF the main breaker and pull
out the plug from the outlet.
For NATIONWIDE SERVICE call 1(800)225-9293
13
MANUAL OPERATION
Procedure
Turn on the breaker and press the upper
part of START key. The SHRED READY
screen appears.
Note: If idle for more than 5 minutes it
goes into the power save mode and all
power goes off. Press the upper part of the
START key again to restore.
Press the START key the cutters start
running and the screen changes as shown in
right.
Display
Feed the paper straight forward into the
feed opening by aligning the center part to
the AUTO START MARK. When paper is drawing
into the shredder, remove your hands
immediately.
Shredding volume is displayed in 4 levels
as shown in the right.
● It is recommended to shred the paper
with the volume of (a) to (c) levels.
● If the paper to be shredded exceeds the
level (d), auto-reverse function may
work.
Note: Shred levels vary depending on the
paper quality and/or voltage fluctuation so
take these levels as a reference.
For NATIONWIDE SERVICE call 1(800)225-9293
14
MANUAL OPERATION Cont….
Procedure
The cutters stop automatically
approximately 10 seconds after the paper
disappears from the feed opening and the
screen changes to SHRED READY.
For continuous shredding, feed the next
paper within 10seconds
To stop the shredding during operation,
press the STOP key. The cutters will stop if
the paper has disappeared from the feed
opening when the STOP key is pressed the
screen (a) is displayed. If it remains the
screen (b) is displayed. In this status the
alarm beeps continuously.
After using the shredder turn OFF the main
breaker and pull out the plug from the
outlet.
Display
Reverse Operation
Procedure
Reverse operation is possible while one of
the following 3 screens displays.
● SHRED READY
● SHRED RUNS BY START KEY
PRESS, OR
● OVERLOADING: REMOVE PAPER
Display
Press the REVERSE key. While you are
pressing the key, the cutter rotates in
reverse direction.
For NATIONWIDE SERVICE call 1(800)225-9293
15
MANUAL OPERATION Cont….
Discarding Waste
Procedure
When the waste basket is full, the status
information beep sounds and the shredder
evens out the particle automatically for
about 10 seconds.
Display
Do not open the cabinet door during this
operation.
After 10 seconds, the display changes as
shown on the right. Open the cabinet door
and shake the basket lightly by hand to
level off the particles.
Not: When the cabinet door opens, all
power goes off for safety.
If the particles reach the height of the
basket handles, take the basket out and
discard the shreds.
For NATIONWIDE SERVICE call 1(800)225-9293
16
TROUBLESHOOTING
Error Messages
Error No.
Error 1
Error 2
Error 3
Error 4
Error 8
Cause
If paper or any foreign article is fed
at the feed opening and left there
without shredding for about 3
minutes, the machine locks up
temporarily and Error 1 is displayed.
After the auto-reverse function is
activated, and if the paper still
remains at feed opening for about 2
minutes, the machine locks up
temporarily and Error 2 is displayed.
If the shredder is operated
continuously for more than 30
minutes, the machine locks up
temporarily and Error 3 is displayed
If the waste leveling motor is
locked, the machine locks up
temporarily to protect the motor
from burning and Error 4 is
displayed.
If overheating prevention of
controller works, Error 9 is
displayed.
Error 6
Error 7
If any malfunction of controller
occurs, Error 6 or 7 is displayed.
Error 9
If LCD has any problem, Error 9 is
displayed.
Corrective Action
1) Turn OFF the breaker and
pull out the plug.
2) Remove the paper or foreign
article at the feed opening.
3) Turn ON the breaker again.
1) turn OFF the breaker and pull out
the plug.
2) Remove the paper at the feed
opening.
3) Turn ON the breaker again.
1) Turn OFF the breaker.
2) Turn ON the breaker again.
1) Turn OFF breaker.
2) Check the waste basket, if it is
full empty the basket.
3) Turn ON the breaker.
1) Turn OFF the breaker and wait
for a certain period of time.
2) Turn ON the breaker.
3) If the error still occurs, contact
SEM’s Customer Service at
1(800)225-9293
1) Reset the breaker.
2) If the error still occurs, contact
SEM’s Customer Service at
1(800)225-9293
1) Reset the breaker.
20 If the error still occurs, contact
SEM’s Customer Service at
1(800)225-9293
If any error occurs after taking the corrective actions mentioned above, check the error
number and contact SEM’s Customer service at 1 (800)225-9293. Do not attempt to
conduct any actions other than the ones mentioned above.
For NATIONWIDE SERVICE call 1(800)225-9293
17
TROUBLESHOOTING Cont…
Common Troubleshooting
Symptom
Shredder does not start
shredding even when paper
is fed manually
Shredder does not stop
Shredder moves back when
paper is fed.
Paper is not shredded
smoothly
Corrective Action
Confirm power source is
OK
Check to see that the plug
is inserted into the outlet.
Confirm that the breaker is
ON.
Check to see if the auto-cut
is not activated.
Check to see if the overflow
stop is not activated.
Check to see if the sensor at
the feed opening is not
activated.
Check the machine to see if
it is in the power save
mode.
Check to see if the cabinet
cover is closed.
Check for any error
message displayed on the
screen.
Check to see if paper is
stuck in the feed opening. If
yes,
1) Press the STOP key
2) Pull out the plug
3) Remove the paper
Check for too many sheets
being fed
Check the quality of the
paper.
Do not cut cardboard or wet
paper
Refer to
____
____
____
Page 9
Page 9
Page 9
Page 12
Page 9
Page 16
____
____
Page 5 & 12
For NATIONWIDE SERVICE call 1(800)225-9293
18
DAILY MAINTENANCE
Warning
Do not dismantle or repair the product. Sharp cutters inside
may cause injury. Opening or removal of covers allows you
to access dangerous moving parts and live parts inside and
accessing such parts may cause injury.
Caution
Always pull out the plug before cleaning or
Performing any type of maintenance to avoid
Electric shock.
Do not use oils or sprays on the shredder.
It may cause a fire or explosion.
Do not use water for cleaning the shredder.
It may cause electric shock.
Do not use polishing powder, thinner,
petroleum-based products or aerosols of any
kinds on or near the shredder at anytime. It may
cause damage, deformation, discoloration or flaw.
Procedure
Pull out the plug before cleaning or performing any type of maintenance.
Clean the shredder cabinet with dry and soft cloth. If there is heavy stain on a cabinet,
soak a soft cloth into a neutral detergent, squeeze it and wipe the stain out with it. Then
wipe the cabinet with dry soft cloth.
Note: For your safety, maintenance and cleaning should be limited to the exterior of
shredder.
For NATIONWIDE SERVICE call 1(800)225-9293
19
Parts List
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Description
Part No.
Quantity
Instruction Manual
SMSZ48335A11
1
Rating Name Plate
Machine Number Plate
Machine Name Plate
Label for Disassemble Prohibition
MS43 Packing Complete Set
Waste Bag M
Waste Box
Cover
Upper Cover
Plate for Protection Against
Vibration *Large
Plate for Protection Against
Vibration *Middle
Plate for Protection Against
Vibration *Small
Instruction Plate
Upper Cover Rubber (rear)
Positioning Plate
Spacer
STOP Button Reinforcement Plate
Spacer
Operation Plate
Display Window
Reverse Button
Stop Button
Start Button
Switch PC Button
S/W Relay Wire
Board Cover 2
Spacer
Spacer
Fireproofing Film Grommet
Shooting Plate Assembly
Loading Slot Plate
Loading Slot Cusion
Loading Slot Shaft
Stretch Spring
Loading Slot SW Assembly
Warning Plate
Auto Start
Waste Light Sensor Packing
Loading Slot Relay Wire
Ground Wire
Main Body Housing
Magnet Catch
SMSZ48329A11
SMSZ48078A11
SMSZ48332A11
SMSZ47966B11
SMSZ47345A01
SMSZ46537A01
SMSZ6470B11
SMSZ8312A11
SMSZ1587D01
1
1
1
1
1
1
1
1
1
SMSZ45729B11
1
SMSZ45730A12
4
SMSZ45731B11
1
SMSZ31068B11
SMSZ8193A12
SMSZ30304F11
SMCP-403
SMSZ48065B11
SMASP-422
SMSZ31067A12
SMSZ47095C11
SMSZ47909A11
SMSZ47908A11
SMSZ47907A11
SMSZ31124B01
SMSZ45702A01
SMSZ47999B11
SMBSP-408E
SMASP-418
SMC-30-SG-22A-UL
SMSZ30957E01
SMSZ30308A12
SMSZ46326B11
SMSZ45996E11
SMSZ46057A11
SMSZ47055C01
SMSZ31069B11
SMGP2A20
SMSZ44217B11
SMSZ45697A01
SMSZ48026A02
SMSZ1500N01
SMTL-185
1
6
1
3
1
2
1
1
1
1
1
1
1
1
1
3
1
1
1
2
1
1
1
1
1
3
1
1
1
1
For NATIONWIDE SERVICE call 1(800)225-9293
20
Parts List Cotn…..
No.
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Description
Handle (main body)
Breaker Cord Assembly (UL)
One Touch Bush
Cord Fitting Plate
Cord Bush
Waste Box Rail
Waste Sensor Case
Photo Sensor
Plate for Sensor
Waste Sensor Harness
Caster (with brake)
Caster (without brake)
Cord Exit Plate (UL)
Earthing Plate
Pivot (upper)
Pivot Metal Washer
Pivot (lower)
Door
Adhension Plate
Door Rubber
Rubber Cusion
Handle (door)
Front Plate
Micro Switch (door)
Terminal Protection Cover
Label for Handling Waste (UL)
Label for Waste Box (UL)
Circuit Breaker 10A
Breaker Relay Cord-Front Plate
Breaker Relay Harness
Ground Wire
Frame (left)
Frame (right)
Free Bush
Rubber for Protection Against Vibration
Stay
Front Cover
One Touch Bush
Fan Sensor Case
Swivel Sensor Harness
Diselectrification Brush Metal Fitting
Diselectrification Brush
Rear Cover
Control Circuit
Harness Assembly
Harness Assembly
Part No.
SMSZ47171B11
SMSZ48122A01
SMSB562-7
SMSZ8731B12
SMSB8R-1
SMSZ3059AC11
SMSZ30593D11
SMGP2A22
SMSZ44760A11
SMSZ46215A01
SMP60GS
SMP-60G
SMSZ48030B11
SMSZ8584A11
SMSZ7408B011
SMSZ8505A11
SMSZ44759A01
SMSZ2928A01
SMSZ8323A12
SMSZ44279A11
SMSZ46992B11
SMSZ30717B11
SMSZ31070C01
SMA-20GV-B
SMAP-B
SMSZ47964B11
SMSZ47965B11
SM3130-Q110-10A
SMSZ48032B01
SMSZ48088A01
SMSZ48026A01
SMSZ2691C01
SMSZ2747E01
SMU-BUSH-KG-32
SMSZ4684C11
SMSZ4664A11
SMSZ30803C11
SMTB-1520
SMSZ30801C11
SMSZ47063E01
SMSZ47352B11
SMSZ47353A11
SMSZ6958H11
SMSZMS-4XINV(UL)
SMSK1-40301
SMSK1-40305
Quantity
2
1
1
1
1
2
1
2
2
1
2
2
1
3
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
2
1
1
1
1
1
1
1
1
1
1
For NATIONWIDE SERVICE call 1(800)225-9293
21
Parts List Cont….
No.
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
Description
Harness Assembly
Harness Assembly
Caution Name Plate for High Temperature
Chip Cover
IVS-4 Motor
Spur Gear Z48
Parallel Key
Housing Stay
Bearing Frame (right)
Bearing Frame (left)
Main Cutter
Subsidiary Cutter
Paralle Key
Ball Bearing
Fixture Bar for Cutter Diaphragm
Cutter Diaphragm
Washer
Washer
Spur Gear Z71
Spur Gear SZ52
Reverse Gear Z=29
Bearing Reinforcing Plate
Spiral Cutter
Labyrinth Seal for 400W
Cone Roller Bearing
Spiral Cutter Frame
Shred Stopper Metal
Cutter Frame Supporting Plate (right)
Housing (right)
Adjusting Ring
Wave Washer
Cutter Frame Supporting Plate (left)
Housing (left)
Ring (3)
Spur Gear Z26
F Cutter
Lenear Diagram for Shreds Leveling Motor
Condenser for Motor Operation
Motor Fixture Plate
Circle Bearing
Parallel Bearing
Harness Cover for Fan Motor
Circle Assy
Part No.
SMSK1-4011
SMSK-301894
SMSZ48123A11
SMSZ44723C11
SMMS-4(1U)
SMSZ46074A11
SM7x7x14
SMSZ6967E11
SMSZ685F11
SMSZ686G11
SMSZ1403C11
SMSZ1404C11
SM7X7X16
SM6005ZZNR
SMSZ45460B11
SMSZ30076B11
SMSZ4951B11
SMSZ4951A12
SMSZ46075A11
SMSZ45434C11
SMSZ45432C11
SMSZ45681D11
SMSZ2650B11
SMSZ46169B11
SMHR30205J
SMSZ2697B11
SMSZ45846A11
SMSZ30097E11
SMSZ3884C11
SMSZ4708B11
SMSZ4958A11
SMSZ30097E12
SMSZ3885B11
SMSZ4660C11
SMSZ45449C01
SMSZ30177A11
SMSZ48028A01
SMUP45B604U2849A
SMSZ30592D11
SMSZ46799B11
SMSZ46984A11
SMSZ48040A11
SMSZ30072A02
Quantity
1
1
2
1
1
1
1
1
1
1
1
1
4
4
4
56
9
3
1
1
2
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
For NATIONWIDE SERVICE call 1(800)225-9293
22
For NATIONWIDE SERVICE call 1(800)225-9293
23
For NATIONWIDE SERVICE call 1(800)225-9293
24
For NATIONWIDE SERVICE call 1(800)225-9293
25
For NATIONWIDE SERVICE call 1(800)225-9293
26
For NATIONWIDE SERVICE call 1(800)225-9293
27
For NATIONWIDE SERVICE call 1(800)225-9293
28
For NATIONWIDE SERVICE call 1(800)225-9293
29
For NATIONWIDE SERVICE call 1(800)225-9293
30
For NATIONWIDE SERVICE call 1(800)225-9293
31
For NATIONWIDE SERVICE call 1(800)225-9293
32
For NATIONWIDE SERVICE call 1(800)225-9293
33
For NATIONWIDE SERVICE call 1(800)225-9293
34
For NATIONWIDE SERVICE call 1(800)225-9293
35
For NATIONWIDE SERVICE call 1(800)225-9293
36