MULTIQUIP DCA125USI3CAN Specifications

Operation and Parts Manual
®
MODEL DCA125USI3CAN
60 hz generator
(isuzu 4hk1x DIESEL ENGINE)
PARTS LIST NO. M3874400004
Revision #2 (09/24/13)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
fuel and chemical warnings
Diesel engine exhaust and some of
its constituents are know to cause
cancer, birth defects and other
reproductive harm.
page 2 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Reporting Safety Defects
If you believe that your vehicle has a defect that could cause a crash or could
cause injury or death, you should immediately inform the National Highway
Traffic Safety Administration (NHTSA) in addition to notifying Multiquip at
1-800-421-1244.
If NHTSA receives similar complaints, it may open an investigation, and if it
finds that a safety defect exists in a group of vehicles, it may order a recall and
remedy campaign. However, NHTSA cannot become involved in individual
problems between you, your dealer, or Multiquip.
To contact NHTSA, you may either call the Vehicle Safety Hotline toll-free at
1-888-327-4236 (TTY: 1-800-424-9153), go to http://www.nhtsa.dot.gov; or
write to:
Administrator
NHTSA
1200 New Jersey Avenue S.E.
Washington, DC 20590
You can also obtain information about motor vehicle safety from
http://www.safecar.gov.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 3
Table of Contents
DCA125USI3CAN Generator
Proposition 65 Warning............................................ 2
Reporting Safety Defects.......................................... 3
Table Of Contents..................................................... 4
Parts Ordering Procedures....................................... 5
Safety Information............................................... 6-11
Specifications......................................................... 12
Dimensions............................................................. 13
Installation.............................................................. 14
Installation.............................................................. 15
General Information................................................ 16
Major Components................................................. 17
Generator Control Panel......................................... 18
Engine Operating Panel.................................... 20-21
Output Terminal Panel Familiarization............... 22-24
Load Application..................................................... 25
Generator Outputs.................................................. 26
Generator Outputs/Gauge Reading........................ 27
Output Terminal Panel Connections.................. 28-29
Inspection/Setup................................................ 30-33
Generator Start-Up Procedure ......................... 34-35
Generator Shut-Down Procedures......................... 36
Maintenance...................................................... 37-40
Trailer Maintenance........................................... 41-44
Trailer Wiring Diagram............................................ 45
Generator Wiring Diagram...................................... 46
Engine Wiring Diagram........................................... 47
Controller Wiring Diagram...................................... 48
Troubleshooting (Generator)................................... 49
Troubleshooting (Diagnostic Lamp)........................ 50
Explanation Of Code In Remarks Column............. 52
Suggested Spare Parts.......................................... 53
Component Drawings
Generator Assembly.......................................... 54-55
Control Box Assembly....................................... 56-59
Engine and Radiator Assembly......................... 60-65
Output Terminal Assembly................................. 66-66
Battery Assembly.............................................. 68-69
Muffler Assembly............................................... 70-71
Fuel Tank Assembly .......................................... 72-73
Enclosure Part 1 Assembly............................... 74-77
Enclosure Part 2 Assembly............................... 78-81
Rubber Seals Assembly.................................... 82-83
Nameplate and Decals Assembly ..................... 84-87
Terms And Conditions Of Sale — Parts................. 88
page 4 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
www.multiquip.com
Parts Ordering Procedures
Ordering parts has never been easier!
Choose from three easy options:
Order via Internet (Dealers Only):
Best Deal!
Effective:
January 1st, 2006
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
❒ Specify Preferred Method of Shipment:
✓ UPS/Fed Ex
✓ DHL
■ Priority One
✓ Truck ■ Ground
■ Next Day
■ Second/Third Day
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 5
Safety Information
Do not operate or service the equipment before reading the
entire manual. Safety precautions should be followed at all
times when operating this equipment. Failure to read and
understand the safety messages and operating instructions
could result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
SaFetY meSSageS
The four safety messages shown below will inform you
about potential hazards that could injure you or others. The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER, WARNiNG, CAuTiON or NotICe.
SaFetY SYmBolS
DANGER
Indicates a hazardous situation which, if not avoided,
WIll result in DEATH or SerIoUS INJUrY.
WARNiNG
Indicates a hazardous situation which, if not avoided,
CoUlD result in DEATH or SerIoUS INJUrY.
CAuTiON
Indicates a hazardous situation which, if not avoided,
CoUlD result in mINor or moDerate INJUrY.
NOTICE
Addresses practices not related to personal injury.
page 6 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Safety Information
geNeral SaFetY
CAuTiON
„ Never operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
„ Never operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
„ Never operate this equipment under the influence of
drugs or alcohol.
„ Never use accessories or attachments that are not
recommended by MQ Power for this equipment. Damage
to the equipment and/or injury to user may result.
„ alWaYS know the location of the nearest
fire extinguisher.
„ alWaYS know the location of the nearest
first aid kit.
„ alWaYS know the location of the nearest
phone or keep a phone on the job site. Also, know the
phone numbers of the nearest ambulance, doctor and
fire department. This information will be invaluable in
the case of an emergency.
GENERATOR SAFETY
DANGER
„ alWaYS check the equipment for loosened threads or
bolts before starting.
„ DO NOT use the equipment for any purpose other than
its intended purposes or applications.
NOTICE
„ This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
„ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
„ Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
„ Never operate the equipment in an explosive
atmosphere or near combustible materials. An
explosion or fire could result causing severe
bodily harm or even death.
WARNiNG
„ Never disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death. Disconnection of any of these
devices will void all warranties.
CAuTiON
„ Never lubricate components or attempt service on a
running machine.
NOTICE
„ alWaYS ensure generator is on level ground before use.
„ alWaYS keep the machine in proper running condition.
„ Fix damage to machine and replace any broken parts
immediately.
„ alWaYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 7
Safety Information
ENGiNE SAFETY
DANGER
„ The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
cause death if inhaled.
„ The engine of this equipment
requires an adequate free
flow of cooling air. Never
operate this equipment in
any enclosed or narrow area
where free flow of the air is
restricted. If the air flow is
restricted it will cause injury to people and property and
serious damage to the equipment or engine.
WARNiNG
„ DO NOT place hands or fingers inside engine
compartment when engine is running.
„ Never operate the engine with heat shields or
guards removed.
„ Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
„ DO NOT remove the radiator cap while the
engine is hot. High pressure boiling water
will gush out of the radiator and severely
scald any persons in the general area of
the generator.
„ DO NOT remove the coolant drain plug while the engine
is hot. Hot coolant will gush out of the coolant tank and
severely scald any persons in the general area of the
generator.
„ DO NOT remove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
generator.
CAuTiON
„ Never touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to cool
before servicing equipment.
NOTICE
„ Never run engine without an air filter or with a dirty air
filter. Severe engine damage may occur. Service air filter
frequently to prevent engine malfunction.
„ Never tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
„ Wet stacking is a common problem with diesel engines
which are operated for extended periods with light or
no load applied. When a diesel engine operates without
sufficient load (less than 40% of the rated output), it will
not operate at its optimum temperature. This will allow
unburned fuel to accumulate in the exhaust system,
which can foul the fuel injectors, engine valves and
exhaust system, including turbochargers, and reduce
the operating performance.
In order for a diesel engine to operate at peak efficiency,
it must be able to provide fuel and air in the proper ratio
and at a high enough engine temperature for the engine
to completely burn all of the fuel.
Wet stacking does not usually cause any permanent
damage and can be alleviated if additional load is
applied to relieve the condition. It can reduce the system
performance and increase maintenance. Applying an
increasing load over a period of time until the excess
fuel is burned off and the system capacity is reached
usually can repair the condition. This can take several
hours to burn off the accumulated unburned fuel.
„ State Health Safety Codes and Public Resources
Codes specify that in certain locations, spark arresters
must be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed
to prevent accidental discharge of sparks or flames
from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this
purpose. In order to comply with local laws regarding
spark arresters, consult the engine distributor or the
local Health and Safety Administrator.
page 8 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Safety Information
FUel SaFetY
DANGER
„ DO NOT start the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
„ Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer “gross
vehicle weight rating.”
„ alWaYS inspect the hitch and coupling for wear. Never
tow a trailer with defective hitches, couplings, chains, etc.
„ alWaYS refuel in a well-ventilated area, away from
sparks and open flames.
„ Check the tire air pressure on both towing vehicle and
trailer. Trailer tires should be inflated to 50 psi cold.
Also check the tire tread wear on both vehicles.
„ alWaYS use extreme caution when working with
flammable liquids.
„ alWaYS make sure the trailer is equipped with a safety
chain.
„ DO NOT fill the fuel tank while the engine is running
or hot.
„ alWaYS properly attach trailer’s safety chains to towing
vehicle.
„ DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
„ alWaYS make sure the vehicle and trailer directional,
backup, brake and trailer lights are connected and
working properly.
„ Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
„ DOT Requirements include the following:
„ Never use fuel as a cleaning agent.
„ DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
TOWiNG SAFETY
CAuTiON
„ Check with your local county or state safety
towing regulations, in addition to meeting
Department of Transportation (DOT)
Safety Towing Regulations, before towing
your generator.
„ Refer to MQ Power trailer manual for additional safety
information.
„ In order to reduce the possibility of an accident while
transporting the generator on public roads, alWaYS
make sure the trailer that supports the generator and
the towing vehicle are mechanically sound and in good
operating condition.
„ alWaYS shutdown engine before transporting
•Connectandtestelectricbrakeoperation.
• Secure portable power cables in cable tray with tie
wraps.
„ The maximum speed for highway towing is 55 mph unless
posted otherwise. Recommended off-road towing is not to
exceed 15 mph or less depending on type of terrain.
„ Avoid sudden stops and starts. This can cause skidding,
or jack-knifing. Smooth, gradual starts and stops will
improve towing.
„ Avoid sharp turns to prevent rolling.
„ Trailer should be adjusted to a level position at all times
when towing.
„ Raise and lock trailer wheel stand in up position when
towing.
„ Place chock blocks underneath wheel to prevent rolling
while parked.
„ Place support blocks underneath the trailer’s bumper
to prevent tipping while parked.
„ Use the trailer’s swivel jack to adjust the trailer height to
a level position while parked.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 9
Safety Information
eleCtrICal SaFetY
DANGER
„ DO NOT touch output terminals during
operation. Contact with output terminals
during operation can cause electrocution,
electrical shock or burn.
„ The electrical voltage required to
operate the generator can cause severe
injury or even death through physical contact with live
circuits. Turn generator and all circuit breakers OFF
before performing maintenance on the generator or
making contact with output terminals.
„ Never insert any objects into the output
receptacles during operation. This is
extremely dangerous. The possibility exists
of electrical shock, electrocution or
death.
„ Backfeed to a utility system can cause
electrocution and/or property damage.
Never connect the generator to a
building’s electrical system without
a transfer switch or other approved
device. All installations should be
performed by a licensed electrician in accordance with
all applicable laws and electrical codes. Failure to do so
could result in electrical shock or burn, causing serious
injury or even death.
„ Make sure power cables are securely connected to the
generator’s output receptacles. Incorrect connections
may cause electrical shock and damage to the
generator.
NOTICE
„ alWaYS make certain that proper power or extension
cord has been selected for the job. See Cable Selection
Chart in this manual.
Grounding Safety
DANGER
„ alWaYS make sure that electrical circuits are properly
grounded to a suitable earth ground (ground rod) per
the National Electrical Code (NEC) and local codes
before operating generator. Severe injury or death by
electrocution can result from operating an ungrounded
generator.
„ Never use gas piping as an electrical ground.
power Cord/Cable Safety
DANGER
„ Never let power cords or cables lay in water.
„ Never stand in water while AC power from the
generator is being transferred to a load.
„ Never use damaged or worn cables or cords when
connecting equipment to generator. Inspect for cuts in
the insulation.
„ Never grab or touch a live power
cord or cable with wet hands. The
possibility exists of electrical shock,
electrocution or death.
page 10 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Safety Information
BatterY SaFetY
DANGER
„ DO NOT drop the battery. There is a possibility that the
battery will explode.
„ DO NOT expose the battery to open flames,
sparks, cigarettes, etc. The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
WARNiNG
eNvIroNmeNtal SaFetY
NOTICE
„ Dispose of hazardous waste properly.
Examples of potentially hazardous waste
are used motor oil, fuel and fuel filters.
„ DO NOT use food or plastic containers to
dispose of hazardous waste.
„ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
„ alWaYS wear safety glasses when handling
the battery to avoid eye irritation. The battery
contains acids that can cause injury to the
eyes and skin.
„ Use well-insulated gloves when picking up the battery.
„ alWaYS keep the battery charged. If the battery is not
charged, combustible gas will build up.
„ alWaYS recharge the battery in a well-ventilated
environment to avoid the risk of a dangerous concentration
of combustible gasses.
„ If the battery liquid (dilute sulfuric acid) comes into
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
„ If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
CAuTiON
„ alWaYS disconnect the NegatIve battery terminal
before performing service on the generator.
„ alWaYS keep battery cables in good working condition.
Repair or replace all worn cables.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 11
Specifications
Table 1. Generator Specifications
Model
DCA125USI3CAN
Revolving field, self ventilated,
Type
open protected type synchronous generator
Armature Connection
Star with Neutral
Zigzag
Phase
3
1
Standby Output
110 kW (137.5 kVA)
79 kW
Prime Output
100 kW (100 kVA)
72 kW
3Ø Voltage (L-L/L-N)
208Y/120, 220Y/127,
N/A
Voltage Selector Switch at 3Ø 240/139
240Y/139
3Ø Voltage (L-L/L-N)
416Y/240, 440Y/254,
N/A
Voltage Selector Switch at 3Ø 480/277
480Y/277
1Ø Voltage (L-L/L-N)
N/A
240/120
Voltage Selector Switch at 1Ø 240/120
Power Factor
0.8
1.0
Frequency
60 Hz
Speed
1800 rpm
Aux. AC Power
Single Phase, 60 Hz
Aux. Voltage/Output
120V/4.8 Kw (2.4 kW x 2)
Sound Level dB (A)
65
Full Load at 23 ft. (7.0 Meters)
Dry Weight
5,689 lbs. (2,580 kg)
Wet Weight
7,012 lbs. (3,180 kg)
Table 2. Engine Specifications
Model
ISUZU 4HK1XYGD-03 Tier 3
4 cycle, water-cooled, direct injection, turbocharged,
Type
air to air intercooled
No. of Cylinders
4 cylinders
Bore x Stroke
4.53 in. x 4.92 in. (115 mm x 125 mm)
Displacement
317 cu. in. (5193 cc)
Rated Output
152 HP/1800 RPM
Starting
Electric
Coolant Capacity
5.2 gal. (19.7 liters)
Lube Oil Capacity
6.1 gal. (23.4 liters)
Fuel Type
#2 Diesel Fuel
Fuel Leak Warning Capacity
42.3gal. (160 liters)
Fuel Tank Capacity
169 gal. (640 liters)
7.3 gal. (27.6 L)/hr at full
5.7 gal. (21.7 L)/hr at 3/4
load
load
Fuel Consumption
4.0 gal. (15.1 L)/hr at 1/2
2.4 gal. (9.1 L)/hr at 1/4
load
load
Battery
12V-128 Ah x 1
page 12 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Dimensions
Figure 1. Dimensions
Table 3. Dimensions
Reference
Letter
Dimension in. (mm)
Reference Letter
Dimension in. (mm)
A
38.20 in. (970 mm.)
F
120.10 in. (3,050 mm.)
B
37.00 in. (940 mm.)
G
73.00 in. (1,855 mm.)
C
36.20 in. (920 mm.)
H
48.80 in. (1,200 mm.)
D
37.00 in. (940 mm.)
E
3620 in. (920 mm.)
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 13
Installation
Figure 2. Typical Generator Grounding Application
page 14 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Installation
Outdoor Installation
Generator Grounding
Install the generator in a area that is free of debris,
bystanders, and overhead obstructions. Make sure the
generator is on secure level ground so that it cannot slide
or shift around. Also install the generator in a manner so
that the exhaust will not be discharged in the direction of
nearby homes.
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and
grounding.
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear to
engine and alternator parts.
CAUTION
Pay close attention to ventilation when operating the
generator inside tunnels and caves. The engine exhaust
contains noxious elements. Engine exhaust must be
routed to a ventilated area.
Indoor Installation
Exhaust gases from diesel engines are extremely
poisonous. Whenever an engine is installed indoors the
exhaust fumes must be vented to the outside. The engine
should be installed at least two feet from any outside wall.
Using an exhaust pipe which is too long or too small can
cause excessive back pressure which will cause the engine
to heat excessively and possibly burn the valves.
Article 250 (Grounding) of the National Electrical Code
(NEC) provides guide lines for proper grounding and
specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of
cable entry as practical.
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
1. Use one of the following wire types to connect the
generator to earth ground.
a. Copper - 10 AWG (5.3 mm2)
b. Aluminum - 8 AWG (8.4 mm2)
2. When grounding the generator (Figure 2) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully. Connect the
other end of the ground cable to earth ground.
3. NEC article 250-52(c) specifies that the earth ground rod
should be buried a minimum of 8 ft. into the ground.
NOTICE
When connecting the generator to any buildings
electrical system ALWAYS consult with a licensed
electrician.
Mounting
The generator must be mounted on a solid foundation (such
as concrete) and set firmly on the foundation to isolate
vibration of the generator when it is running. The generator
must set at least 6 inches above the floor or grade level (in
accordance to NFPA 110, Chapter 5-4.1). DO NOT remove
the metal skids on the bottom of the generator. They are
to resist damage to the bottom of the generator and to
maintain alignment.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 15
General Information
Generator
Open Delta Excitation System
This MQ Power Model generator (Figure 3) is a high quality
portable (requires a trailer for transport) power source for
telecom sites, lighting facilities, power tools, submersible
pumps and other industrial and construction machinery.
This generator is equipped with the state of the art “OpenDelta” excitation system. The open delta system consist
of an electrically independent winding wound among
stationary windings of the AC output section.
There are four connections of the open delta A, B, C and
D. During steady state loads, the power from the voltage
regulator is supplied from the parallel connections of A to
B, A to D, and C to D. These three phases of the voltage
input to the voltage regulator are then rectified and are the
excitation current for the exciter section.
When a heavy load, such as a motor starting or a short
circuit occurs, the automatic voltage regulator (AVR)
switches the configuration of the open delta to the series
connection of B to C. This has the effect of adding the
voltages of each phase to provide higher excitation to the
exciter section and thus better voltage response during the
application of heavy loads.
The connections of the AVR to the AC output windings are
for sensing only. No power is required from these windings.
The open-delta design provides virtually unlimited excitation
current, offering maximum motor starting capabilities. The
excitation does not have a “fixed ceiling” and responds
according the demands of the required load.
Engine Operating Panel
The “Engine Operating Panel” is provided with the following:
„„Tachometer
„„Water Temperature Gauge
„„Warning Lamp
„„Pre-Heat Lamp
„„Oil Pressure Gauge
„„Charging Ammeter Gauge
„„Fuel Level Gauge
„„Fuel Leak Detection Lamp
„„Panel Light/Panel Light Switch
„„ECU Controller
„„Engine Speed Switch
„„Warning Lamp (Diagnostic Lamp)
Generator Control Panel
The “Generator Control Panel” is provided with the following:
„„Frequency Meter (Hz)
„„AC Ammeter (Amps)
„„AC Voltmeter (Volts)
„„Ammeter Change-Over Switch
„„Voltmeter Change-Over Switch
„„Voltage Regulator
„„3-Pole, 350 amp Main Circuit Breaker
„„“Control Box” (located behind the Gen. Control Panel)
•Automatic Voltage Regulator
•Current Transformer
•Over-Current Relay
•Starter Relay
•Voltage Selector Switch
•Diagnostic Switch
Output Terminal Panel
The “Output Terminal Panel” is provided with the following:
„„Three 120/240V output receptacles (CS-6369), 50A
„„Three auxiliary circuit breakers, 50A
„„Two 120V output receptacles (GFCI), 20A
„„Two GFCI circuit breakers, 20A
„„Five output terminal lugs (3Ø power)
„„Battery Charger (Optional)
„„Jacket Water Heater (Optional)
„„Low Coolant Level Switch
Engine
The DCA125USI3CAN is powered by a 4 cylinder, water
cooled, direct injection, turbocharged ISUZU 4HK1X diesel
engine. This engine is designed to meet every performance
requirement for the generator. Reference Table 2 for engine
specifications.
In keeping with MQ Power’s policy of constantly improving
its products, the specifications quoted herein are subject
to change without prior notice.
Electric Governor System
The electric governor system controls the RPMs of the engine.
When the engine demand increases or decreases, the
governor system regulates the frequency variation to ±.25%.
Extension Cables
When electric power is to be provided to various tools or
loads at some distance from the generator, extension cords
are normally used. Cables should be sized to allow for
distance in length and amperage so that the voltage drop
between the generator and point of use (load) is held to
a minimum. Use the cable selection chart (Table 6) as a
guide for selecting proper extension cable size.
page 16 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Major Components
Table 4. Generator Major Components
ITEM NO.
DESCRIPTION
1
Muffler Assembly
2
Engine Assembly
3
Enclosure Assembly
4
Generator Assembly
5
Output Terminal Assembly
6
Fuel Tank Assembly
7
Battery Assembly
8
Engine Operating Panel Assembly
9
Generator Control Panel Assembly
Figure 3. Major Components
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 17
Generator Control Panel
Figure 4. Generator Control Panel
The definitions below describe the controls and functions
of the Generator Control Panel (Figure 4).
1. Main Circuit Breaker—This three-pole, 350A main
breaker is provided to protect the U,V, and W Output
Terminal Lugs from overload.
2. Voltage Regulator Control — Allows ±15% manual
adjustment of the generator’s output voltage.
Located behind the generator control panel is the Generator
Control Box. This box contains some of the necessary
electronic components required to make the generator
function.
The Control Box is equipped with the following major
components:
„„Over-Current Relay
3. Ammeter Change-Over Switch — This switch allows
the AC ammeter to indicate the current flowing to the
load connected to any phase of the output terminals,
or to be switched off. This switch does not effect the
generator output in any fashion, it is for current reading
only.
„„Automatic Voltage Regulator (AVR)
4. Voltmeter Change-Over Switch — This switch allows
the AC voltmeter to indicate phase to phase voltage
between any two phases of the output terminals or to
be switched off.
„„Main Circuit Breaker
5. Frequency Meter — Indicates the output frequency
in hertz (Hz). Normally 60 Hz.
6. AC Ammeter — Indicates the amount of current the
load is drawing from the generator per leg selected by
the ammeter phase-selector switch.
7. AC Voltmeter — Indicates the output voltage present
at the U,V, and W Output Terminal Lugs.
„„Starter Relay
„„Current Transformer
„„Voltage Selector Switch
NOTICE
Remember the overcurrent relay monitors the current
flowing from the U,V, and W Output Terminal Lugs
to the load.
In the event of a short circuit or over current condition,
it will automatically trip the 350 amp main breaker.
To restore power to the Output Terminal Panel, press
the reset button on the overcurrent relay and place the
main circuit breaker in the closed position (ON).
page 18 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Notes
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 19
ENGINE OPERATING PANEL
Figure 5. Engine Operating Panel
page 20 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
ENGINE OPERATING PANEL
and all major faults will shutdown the generator. During
cranking cycle, the ECU will attempt to crank the engine
for 10 seconds before disengaging.
The definitions below describe the controls and functions
of the Engine Operating Panel (Figure 5).
1. Panel Light — Normally used in dark areas or at night
time. When activated, panel lights will illuminate. When
the generator is not in use be sure to turn the panel
light switch to the OFF position.
If the engine does not engage (start) by the third
attempt, the engine will be shutdown by the engine
controller’s Over Crank Protection mode. If the engine
engages at a speed (RPM's) that is not safe, the
controller will shutdown the engine by initializing the
Over Speed Protection mode.
Also the engine controller will shut down the engine in
the event of low oil pressure, high coolant temperature,
low coolant level, and loss of magnetic pickup.
These conditions can be observed by monitoring the
LED status indicators on the front of the controller
module.
2. Panel Light Switch — When activated will turn on
control panel light.
3. Preheat Lamp — As the engine cranks, this lamp
will illuminate to indicate automatic preheating of
the engine glow plugs. When the lamp turns off, this
indicates that the preheat cycle is complete and the
engine will start automatically.
4. Warning Lamp (Diagnostic Lamp) — When lit
indicates a that a failure has occurred in the engine
control system.
5. Fuel Leak Detection Lamp — This lamp will illuminate
when a leak in the fuel tank containment enclosure is
detected.
6. Engine Speed Switch — This switch controls the
speed of the engine (low/high).
7. Oil Pressure Gauge — During normal operation this
gauge should read between 42 ~71 psi. (290~490 kPa).
When starting the generator the oil pressure may read
a little higher, but after the engine warms up the oil
pressure should return to the correct pressure range.
8. Water Temperature Gauge — During normal operation
this gauge be should read between 167°~203°F (75°
~95°C).
9. Charging Ammeter Gauge — Indicates the current
being supplied by the engine’s alternator which
provides current for generator’s control circuits and
battery charging system.
10. Fuel Gauge — Indicates amount of diesel fuel
available.
11. Tachometer — Indicates engine speed in RPM’s for
60 Hz operation. This meter should indicate 1800
RPM’s when the rated load is applied. In addition a
built in hour meter will record the number of operational
hours that the generator has been in use.
12. Auto START/STOP Engine
Controller (ECU) — This controller
has a vertical row of status LED's
(inset), that when lit, indicate
that an engine malfunction (fault)
has been detected. When a fault
has been detected the engine
controller will evaluate the fault
A. MPEC Control Switch — This switch controls the
running of the unit. If this switch is set to the OFF/
RESET position, the unit will not run. When this switch
is set to the manual position, the generator will start
immediately.
If the generator is to be connected to a building’s
AC power source via an automatic transfer switch
(isolation), place the switch in the AUTO position. In this
position, should an outage occur, the automatic transfer
switch (ATS) will start the generator automatically
via the generator’s auto-start contacts connected to
the ATS’s start contacts. Please refer to your ATS
installation manual for further instructions for the
correct installation of the auto-start contacts of the
generator to the ATS.
B. Low Oil Pressure — Indicates the engine pressure
has fallen below 15 psi (103 kPa). The oil pressure is
detected using variable resistive values from the oil
pressure sending unit. This is considered a major fault.
C. High Coolant Temperature — Indicates the engine
temperature has exceeded 230°F (110°C). The engine
temperature is detected using variable resistive values
from the temperature sending unit. This is considered
a major fault.
D. Overcrank Shutdown — Indicates the unit has
attempted to start a pre- programmed number of
times, and has failed to start. The number of cycles and
duration are programmable. It is pre-set at 3 cycles with
a 10 second duration. This is considered a major fault.
E. Overspeed Shutdown — Indicates the engine is
running at an unsafe speed. This is considered a
major fault.
F. Engine Running — Indicates that engine is running
at a safe operating speed.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 21
OUTPUT TERMINAL PANEL FAMILIARIZATION
Output Terminal Panel
Output Terminal Familiarization
The Output Terminal Panel (Figure 6) shown below is
located on the right-hand side (left from control panel) of
the generator. Lift up on the cover to gain access to
receptacles and terminal lugs.
The “Output Terminal Panel ” (Figure 6) is provided with
the following:
„„Three 120/240V output receptacles @ 50 amp
NOTICE
„„Three Circuit Breakers @ 50 amps
Terminal legs “O” and “Ground” are considered bonded
grounds.
„„Two 120V GFCI receptacles @ 20 amp
„„Two GFCI Circuit Breakers @ 20 amps
„„Five Output Terminal Lugs ( U, V, W, O, Ground)
Figure 6. Output Terminal Panel
page 22 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
OUTPUT TERMINAL PANEL FAMILIARIZATION
120 VAC GFCI Receptacles
There are two 120 VAC, 20 amp GFCI (Duplex Nema
5-20R) receptacles provided on the output terminal panel.
These receptacles can be accessed in any voltage
selector switch position. Each receptacle is protected by a
20 amp circuit breaker. These breakers are located directly
above the GFCI receptacles. Remember the load output
(current) of both GFCI receptacles is dependent on the load
requirements of the U, V, and W output terminal lugs.
Pressing the reset button resets the GFCI receptacle after
being tripped. Pressing the test button (Figure 7) in the
center of the receptacle will check the GFCI function. Both
receptacles should be tested at least once a month.
Each auxiliary receptacle is protected by a 50 amp circuit
breaker. These breakers are located directly above the
GFCI receptacles. Remember the load output (current) on
all three receptacles is dependent on the load requirements
of the output terminal lugs.
Turn the voltage regulator control knob (Figure 9) on the
control panel to obtain the desired voltage. Turning the knob
clockwise will increase the voltage, turning the knob
counter-clockwise will decrease the voltage.
Figure 9. Voltage Regulator Control Knob
Removing the Plastic Face Plate (Hard Wire Hookup
Panel)
The output terminal lugs are protected by a plastic face
plate cover (Figure 10). Unscrew the securing bolts and
lift the plastic terminal cover to gain access to the terminal
enclosure.
After the load wires have been securely attached to the
terminal lugs, reinstall the plastic face plate.
Figure 7. G.F.C.I. Receptacle
Twist Lock Dual Voltage 120/240 VAC Receptacles
There are three 120/240V, 50 amp auxiliary twist-lock (CS6369) receptacles (Figure 8) provided on the output
terminal panel. These receptacles can only be accessed
when the voltage selector switch is placed in the singlephase 240/120 position.
Figure 10. Plastic Face Plate
(Output Terminal Lugs)
Figure 8. 120/240V Twist-Lock
Auxiliary Receptacles
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 23
OUTPUT TERMINAL PANEL FAMILIARIZATION
Connecting Loads
Over Current Relay
Loads can be connected to the generator by the output
terminal lugs or the convenience receptacles (Figure 11).
Make sure to read the operation manual before attempting
to connect a load to the generator.
An over current relay (Figure 12) is connected to the main
circuit breaker. In the event of an overload, both the circuit
breaker and the over current relay may trip. If the circuit
breaker can not be reset, the reset button on the over
current relay must be pressed. The over current relay is
located in the control box.
To protect the output terminals from overload, a 3-pole, 350
amp main circuit breaker is provided. Make sure to switch
ALL circuit breakers to the OFF position prior to starting
the engine.
Figure 12. Over Current Relay
Figure 11. Connecting Loads
page 24 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Load Application
Single Phase Load
Three Phase Load
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage, frequency,
and voltage requirements are satisfactorily supplied by the
generator for operating the equipment.
When calculating the power requirements for 3-phase
power use the following equation:
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require
130—150% more wattage than the rating on the nameplate,
as the wattage is influenced by the efficiency, power factor
and starting system of the equipment.
NOTICE
If wattage is not given on the equipment’s name plate,
approximate wattage may be determined by multiplying
nameplate voltage by the nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
The power factor of this generator is 0.8. See Table 5 below
when connecting loads.
Table 5. Power Factor By Load
Type of Load
Power Factor
Single-phase induction motors
0.4-0.75
Electric heaters, incandescent lamps
Fluorescent lamps, mercury lamps
Electronic devices, communication
equipment
Common power tools
1.0
0.4-0.9
Load in Watts
At 100
Volts
2.5
5
0.8
Maximum Allowable Cable Length
At 200
Volts
#10 Wire
#12 Wire
#14 Wire
#16 Wire
300
600
1000 ft.
600 ft.
375 ft.
250 ft.
600
1200
500 ft.
300 ft.
200 ft.
125 ft.
7.5
900
1800
350 ft.
200 ft.
125 ft.
100 ft.
10
1200
2400
250 ft.
150 ft.
100 ft.
15
1800
3600
150 ft.
100 ft.
65 ft.
2400
4800
125 ft.
75 ft.
50 ft.
20
If 3Ø load (kVA) is not given on the equipment
nameplate, approximate 3Ø load may be determined
by multiplying voltage by amperage by 1.732.
NOTICE
Motors and motor-driven equipment draw much greater
current for starting than during operation.
An inadequate size connecting cable which cannot carry the
required load can cause a voltage drop which can burn out
the appliance or tool and overheat the cable. See Table 6.
„„When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up to
the generating set’s rated output (kW) can be used.
„„When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
„„When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
1.0
Table 6. Cable Selection (60 Hz, Single Phase Operation)
Current
in
Amperes
NOTICE
When connecting ordinary power tools, a capacity of up to
the generating set’s rated output (kW) multiplied by 0.8 can
be used.
DANGER
Before connecting this generator to any building’s
electrical system, a licensed electrician must install
an isolation (transfer) switch. Serious damage to
the building’s electrical system may occur without this
transfer switch.
CAUTION: Equipment damage can result from low voltage
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 25
GENERATOR OUTPUTS
Generator Output Voltages
Generator Amperage
A wide range of voltages are available to supply voltage for
many different applications. Voltages are selected by using
the voltage selector switch (Figure 13). To obtain some of
the voltages as listed in Table 7 (see below) will require a
fine adjustment using the voltage regulator (VR) control
knob located on the control panel.
Table 8 shows the maximum amps the generator can
provide. DO NOT exceed the maximum amps as listed..
Table 8. Generator Maximum Amps
Rated Voltage
Voltage Selector Switch
1Ø 120 Volt
The voltage selector switch (Figure 13) is located above
the output terminal panel’s Hard Wire Hook-up Panel. It
has been provided for ease of voltage selection.
1Ø 240 Volt
Maximum Amps
277.8 amps (4 wire)
301A x 2 (Zigzag)
138.9 amps (4 wire)
301A (Zigzag)
3Ø 240 Volt
301 amps
3Ø 480 Volt
150 amps
GFCI Receptacle Load Capability
The load capability of the GFCI receptacles is directly
related to the voltage being supplied at either the output
terminals or the 2 twist lock auxiliary receptacles.
Table 9 and Table 10 show what amount of current is
available at the GFCI receptacles when the output terminals
and twist lock receptacles are in use. Be careful that your
load does not to exceed the available current capability at
the receptacles.
Figure 13. Voltage Selector Switch
Voltage Selector Switch Locking Button
To lock the voltage selector switch, press and hold the
red button located at the bottom of the switch. While
holding the red button down, insert a pad lock into the hole
next to the button to retain it in the inward locked position.
When the lock is removed, the red button is spring loaded
and will return to its normal outward unlocked position.
CAUTION
NEVER change the position of the voltage selector
switch while the engine is running. ALWAYS place
circuit breaker in the OFF position before selecting
voltage.
Table 7. Voltages Available
UVWO Output
Terminal Lugs
Voltage Selector Switch
3-Phase 240/139V Position
Voltage Selector Switch
3-Phase 480/270V Position
3Ø Line-Line
208V
220V
240V
416V
440V
480V
1Ø Line-Neutral
120V
127V
139V
240V
254V
277V
Voltage Selector Switch Single-Phase 240/120V Position
1Ø Line-Neutral/
Line-Line
120V
Line-Neutral
N/A
N/A
240V
Line-Line
N/A
N/A
Table 9. 1Ø GFCI Receptacle Load Capacity
72.0
70.8
Available Load
Current (Amps)
GFCI Duplex
5-20R 120V
0 amps/receptacle
5 amps/receptacle
69.6
10 amps/receptacle
68.4
15 amps/receptacle
67.2
20 amps/receptacle
KW in Use
Twist Lock (C6369)
1Ø 240/120V
Table 10. 3Ø GFCI Receptacle Load Capacity
KVA in Use
(UVWO Terminals)
3Ø 240/480V
Available Load
Current (Amps)
GFCI Duplex
5-20R 120V
125
0 amps/receptacle
121
5 amps/receptacle
117
10 amps/receptacle
113
15 amps/receptacle
108
20 amps/receptacle
page 26 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
GENERATOR OUTPUTS/gauge reading
How to Read the ac ammeter and ac
voltage gauges
The AC ammeter and AC voltmeter gauges are controlled
by the AC ammeter and AC voltmeter change-over
switches.
Both of these switches are located on the control panel and
DO NOT effect the generator output. They are provided to
help observe how much power is being supplied, produced
at the UVWO terminals lugs.
Before taking a reading from either gauge, set the Voltage
Selector Switch (Figure 14) to the position which produces
the required voltage (For example, for 3Ø 240V, choose
the center 3Ø 240/139V position on the voltage selector
switch)
AC Ammeter Gauge Reading
Place the AC Ammeter Change-Over Switch (Figure 17)
in the U position and observe the current reading (load
drain) on the U terminal as indicated on the AC Ammeter
Gauge (Figure 18). This process can be repeated for
terminals V and W.
Figure 17. AC Ammeter
Change-Over Switch
Figure 18. AC Ammeter
(Amp Reading on U Lug)
NOTICE
The ammeter gauge will only show a reading when
the Output Terminal Lugs are connected to a load
and in use.
Figure 14. Voltage Selector Switch
240/139V 3Ø Position
NOTICE
For 3Ø 208V/1Ø,120V, place the Voltage Selector
Switch in the 3 Phase 240/139 position.
AC Voltmeter Gauge Reading
Place the AC Voltmeter Change-Over Switch (Figure 15)
in the W-U position and observe the phase to phase voltage
reading between the W and U terminals as indicated on
the AC Voltmeter Gauge (Figure 16)
Figure 15. AC Voltmeter
Change-Over Switch
Figure 16. AC Voltmeter
Gauge
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 27
OUTPUT TERMINAL PANEL CONNECTIONS
UVWO Terminal Output Voltages
Various output voltages can be obtained using the UVWO
output terminal lugs. The voltages at the terminals are
dependent on the position of the Voltage Selector Switch
and the adjustment of the Voltage Regulator Control
Knob.
Remember the voltage selector switch determines the
range of the output voltage. The voltage regulator (VR)
allows the user to increase or decrease the selected
voltage.
3Ø-240/139 UVWO Terminal Output Voltages
1. Place the voltage selector switch in the 3Ø 240/139
position as shown in Figure 19.
Figure 19. Voltage Selector Switch
3Ø-240/139V Position
2. Connect the load wires to the UVWO terminals as
shown in Figure 20.
3. Turn the voltage regulator knob (Figure 21) clockwise
to increase voltage output, turn counterclockwise to
decrease voltage output. Use voltage regulator
adjustment knob whenever fine tuning of the output
voltage is required.
Figure 21. Voltage Regulator Knob
3Ø-208V/1Ø-120V UVWO Terminal Output Voltages
1. Place the voltage selector switch in the 3Ø 240/139
position as shown in Figure 22.
Figure 22. Voltage Selector Switch
3Ø-240/139V Position
2. Connect the load wires to the UVWO terminals as
shown in Figure 23.
Figure 23. UVWO Terminal Lugs
3Ø-208/1Ø-120V Connections
NOTICE
Figure 20. UVWO Terminal Lugs
3Ø-240/139V Connections
To achieve a 3Ø 208V output the voltage selector switch
must be in the 3Ø-240/139 position and the voltage
regulator must be adjusted to 208V.
page 28 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
OUTPUT TERMINAL PANEL CONNECTIONS
3Ø-480/277V UVWO Terminal Output Voltages
1Ø-240/120V UVWO Terminal Output Voltages
1. Place the voltage selector switch in the 3Ø 480/277
position as shown in Figure 24.
1. Place the voltage selector switch in the 1Ø 240/120
position as shown in Figure 26.
Figure 24. Voltage Selector Switch
3Ø-480/277V Position
Figure 26. Voltage Selector Switch
1Ø-240/120V Position
2. Connect the load wires to the UVWO terminals as
shown in Figure 25.
2. Connect the load wires to the UVWO terminals as
shown in Figure 27.
Figure 25. UVWO Terminal Lugs
3Ø-480/277V Connections
Figure 27. UVWO Terminal Lugs
1Ø-240/120V Connections
3. Turn the voltage regulator knob (Figure 21) clockwise
to increase voltage output, turn counterclockwise
to decrease voltage output. Use voltage regulator
adjustment knob whenever fine tuning of the output
voltage is required.
3. Turn the voltage regulator knob (Figure 21) clockwise
to increase voltage output, turn counterclockwise to
decrease voltage output. Use voltage regulator
adjustment knob whenever fine tuning of the output
voltage is required.
NOTICE
ALWAYS make sure that the connections to the UVWO
terminals are secure and tight. The possibility of arcing
exists, that could cause a fire.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 29
inspection/SETUP
Circuit Breakers
To protect the generator from an overload, a 3-pole, 350
amp, main circuit breaker is provided to protect the U,V,
and W Output Terminals from overload. In addition two
single-pole, 20 amp GFCI circuit breakers are provided to
protect the GFCI receptacles from overload. Three 50 amp
load circuit breakers have also been provided to protect the
auxiliary receptacles from overload. Make sure to switch
ALL circuit breakers to the OFF position prior to starting
the engine.
Lubrication Oil
Fill the engine crankcase with lubricating oil through the
filler hole, but DO NOT overfill. Make sure the generator is
level and verify that the oil level is maintained between the
two notches (Figure 28) on the dipstick. See Table 11 for
proper selection of engine oil.
Fuel Check
DANGER
Fuel spillage on a hot engine can cause
a fire or explosion. If fuel spillage occurs,
wipe up the spilled fuel completely to
prevent fire hazards. NEVER smoke
around or near the generator.
Refilling the Fuel System
CAUTION
ONLY properly trained personnel who have read
and understand this section should refill the fuel tank
system.
This generator has an internal fuel tank (Figure 29) located
inside the enclosure base and may also be equipped with
an additional trailer mounted fuel tank (option). ALWAYS
fill the fuel tanks with clean fresh #2 diesel fuel. DO NOT
fill the fuel tanks beyond their capacities.
Figure 28. Engine Oil Dipstick
When checking the engine oil, be sure to check if the oil is
clean. If the oil is not clean, drain the oil by removing the
oil drain plug, and refill with the specified amount of oil as
outlined in the ISUZU Engine Owner’s Manual. Oil should
be warm before draining.
Other types of motor oils may be substituted if they meet
the following requirements:
„„ API Service Classification CC/SC
„„API Service Classification CC/SD
„„API Service Classification CC/SE
„„API Service Classification CC/SF
Pay attention to the fuel tank capacity when replenishing
fuel. The fuel tank cap must be closed tightly after filling.
Handle fuel in a safety container. If the container does not
have a spout, use a funnel. Wipe up any spilled fuel
immediately.
Table 11. Recommended Motor Oil
Figure 29. Internal Fuel Tank System
page 30 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
inspection/SETUP
Refueling Procedure:
WARNING
2. Remove fuel cap (internal fuel tank) and fill tank as
shown in (Figure 31).
Diesel fuel and its vapors are dangerous
to your health and the surrounding
environment. Avoid skin contact and/or
inhaling fumes.
1. Level Tanks — Make sure fuel cells are level with the
ground. Failure to do so will cause fuel to spill from the
tank before reaching full capacity (Figure 30).
CAUTION
ALWAYS place trailer on firm level ground before
refueling to prevent spilling and maximize the amount
of fuel that can be pumped into the tank.
Figure 31. Fueling the Generator
3. NEVER overfill fuel tank — It is important to read the
fuel gauge when filling trailer fuel tank. DO NOT wait
for fuel to rise in filler neck (Figure 32).
Figure 32. Full Fuel Tank
Figure 30. Only Fill on Level Ground
NOTICE
ONLY use #2 diesel fuel when refueling.
CAUTION
DO NOT OVERFILL fuel system. Leave room for fuel
expansion. Fuel expands when heated (Figure 33).
Figure 33. Fuel Expansion
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 31
inspection/SETUP
Coolant (Antifreeze/Summer Coolant/
Water)
ISUZU recommends ISUZU antifreeze/summer coolant for
use in their engines, which can be purchased in concentrate
(and mixed with 50% demineralized water) or pre-diluted. See
the ISUZU Engine Owner’s Manual for further details.
Cleaning the Radiator
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the
radiator fins with compressed air. Cleaning inside the
machine is dangerous, so clean only with the engine turned
off and the negative battery terminal disconnected.
Air Cleaner
WARNING
If adding coolant/antifreeze mix to the
radiator, DO NOT remove the radiator cap
until the unit has completely cooled. The
possibility of hot! coolant exists which can
cause severe burns.
Day-to-day addition of coolant is done from the recovery
tank. When adding coolant to the radiator, DO NOT remove
the radiator cap until the unit has completely cooled. See
Table 12 for engine, radiator, and recovery tank coolant
capacities. Make sure the coolant level in the recovery tank
is always between the “H” and the “L” markings.
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the ISUZU Engine Owner’s Manual.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear and adjust it in accordance with the
ISUZU Engine Owner’s Manual.
The fan belt tension is proper if the fan belt bends 10 to 15
mm (Figure 34) when depressed with the thumb as shown
below.
Table 12. Coolant Capacity
Engine and Radiator
5.2 gal (19.7 liters)
Reserve Tank
TBD
Operation in Freezing Weather
When operating in freezing weather, be certain the proper
amount of antifreeze (Table 13) has been added.
Table 13. Anti-Freeze
Operating Temperatures
Freezing Point
Vol %
Anti-Freeze
°C
°F
50
-37
-34
Figure 34. Fan Belt Tension
CAUTION
NEVER place hands near the belts or fan
while the generator set is running.
NOTICE
When the antifreeze is mixed with water, the antifreeze
mixing ratio must be less than 50%.
page 32 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
inspection/SETUP
Battery
When connecting battery do the following:
This unit is of negative ground DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level are
not properly maintained. Add only distilled water when
replenishment is necessary.
1. NEVER connect the battery cables to the battery
terminals when the MPEC Control Switch is in either
the MANUAL position. ALWAYS make sure that the
MPEC Control Switch is in the OFF/RESET position
when connecting the battery.
DO NOT over fill. Check to see whether the battery
cables are loose. Poor contact may result in poor starting
or malfunctions. Always keep the terminals firmly
tightened. Coating the terminals with an approved battery
terminal treatment compound. Replace battery with only
recommended type battery.
2. Place a small amount of battery terminal treatment
compound around both battery terminals. This will
ensure a good connection and will help prevent
corrosion around the battery terminals.
The battery is sufficiently charged if the specific gravity
of the battery fluid is 1.28 (at 68° F). If the specific gravity
should fall to 1.245 or lower, it indicates that the battery is
dead and needs to be recharged or replaced.
Before charging the battery with an external electric source,
be sure to disconnect the battery cables.
Battery Cable Installation
ALWAYS be sure the battery cables (Figure 35) are
properly connected to the battery terminals as shown below.
The red cable is connected to the positive terminal of the
battery, and the black cable is connected to the negative
terminal of the battery.
CAUTION
ALWAYS disconnect the negative terminal FIRST and
reconnect negative terminal LAST.
NOTICE
If the battery cable is connected incorrectly, electrical
damage to the generator will occur. Pay close attention to
the polarity of the battery when connecting the battery.
CAUTION
Inadequate battery connections may cause poor
starting of the generator, and create other malfunctions.
Alternator
The polarity of the alternator is negative grounding type.
When an inverted circuit connection takes place, the
circuit will be in short circuit instantaneously resulting the
alternator failure.
DO NOT put water directly on the alternator. Entry of water
into the alternator can cause corrosion and damage the
alternator.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
Piping and Hose Connection
Figure 35. Battery Connections
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness. Tighten all hose clamps and check
hoses for leaks.
If any hose (fuel or oil) lines are defective replace them
immediately.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 33
GENERATOR START-UP PROCEDURE
Before Starting
Starting
CAUTION
The engine’s exhaust contains harmful emissions.
ALWAYS have adequate ventilation when operating.
Direct exhaust away from nearby personnel.
1. Place the voltage selector switch in the desired
voltage position (Figure 38)..
WARNING
NEVER manually start the engine with the main, GFCI or
auxiliary circuit breakers in the ON (closed) position.
1. Place the main, G.F.C.I., and aux. circuit breakers
(Figure 36) in the OFF position prior to starting the
engine.
Figure 38. Voltage Selector Switch
Starting (Manual)
1. Place the engine speed switch (Figure 39) in the LOW
(down) position.
Figure 36. Main, Aux. and GFCI
Circuit Breakers (OFF)
2. Make sure the voltage change-over board has been
configured for the desired output voltage.
3. Connect the load to the receptacles or the output
terminal lugs as shown in Figure 10. These load
connection points can be found on the output terminal
panel and the output terminal panel’s hard wire hookup
panel.
4. Tighten terminal nuts securely to prevent load wires
from slipping out.
Figure 39. Engine Speed Switch (Low)
2. Located in the control box is the engine controller
diagnostic switch (Figure 40). Verify that this switch
has been placed in the OFF position (down).
Figure 40. Diagnostic Switch
3. Place the MPEC control switch in the MANUAL
position to start the engine (Figure 41).
5. Close all engine enclosure doors (Figure 37).
Figure 41. MPEC Control Switch
(Manual Position)
CORRECT
INCORRECT
Figure 37. Engine Enclosure Doors
page 34 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
GENERATOR START-UP PROCEDURE
4. Depending on the temperature of the coolant (cold
weather conditions), the pre-heat lamp (Figure 42) will
light (ON) and remain on until the pre-heating cycle has
been completed. After completion of the pre-heating
cycle, the light will go OFF and the engine will start up
automatically.
8. The generator’s AC-voltmeter (Figure 46) will display
the generator’s output in VOLTS.
Figure 46. Voltmeter
Figure 42. Pre-Heat Lamp
5. Once the engine starts, let the engine run for 1-2
minutes. Listen for any abnormal noises. If any
abnormalities exist, shut down the engine and correct
the problem. If the engine is running smoothly, place
the engine speed switch (Figure 43) in the HIGH (up)
position.
9. If the voltage is not within the specified tolerance, use
the voltage adjustment control knob (Figure 47) to
increase or decrease the desired voltage.
Figure 47. Voltage Adjust Control Knob
Figure 43. Engine Speed Switch (High)
6. Verify that the Engine Running status LED on the
MPEC unit (Figure 44) in ON (lit) after the engine has
been started
10. The ammeter (Figure 48) will indicate zero amps with
no load applied. When a load is applied, the ammeter
will indicate the amount of current that the load is
drawing from the generator.
Figure 48. Ammeter (No Load)
Figure 44. Engine Running LED (ON)
7. The generator’s frequency meter (Figure 45) should be
displaying the 60 cycle output frequency in HERTZ.
11. The engine oil pressure gauge (Figure 49) will indicate
the oil pressure of the engine. Under normal operating
conditions the oil pressure is approximately 42 to 71
psi. (290~490 kPa).
Figure 49. Oil Pressure Gauge
Figure 45. Frequency Meter
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 35
GENERATOR SHUT-DOWN PROCEDURES
12. The coolant temperature gauge (Figure 50) will
indicate the coolant temperature. Under normal
operating conditions the coolant temperature should
be between 167°~203°F (75°~95°C) (Green Zone).
WARNING
NEVER stop the engine suddenly except in an
emergency.
Normal Shutdown Procedure
To shutdown the generator, use the following procedure:
Figure 50. Coolant Temperature Gauge
1. Place both the MAIN, GFCI and LOAD circuit breakers
as shown in Figure 54 to the OFF position..
13. The tachometer gauge (Figure 51) will indicate the
speed of the engine when the generator is operating.
Under normal operating conditions this speed is
approximately 1800 RPM’s.
Figure 54. Main, GFCI and Load
Circuit Breakers Off
Figure 51. Engine Tachometer Gauge
2. Place the engine speed switch (Figure 55) in the “LOW”
(down) position..
14. Place the main, GFCI, and aux. circuit breakers in the
ON position (Figure 52).
Figure 55. Ignition Switch (Normal)
3. Let the engine cool by running it at low speed for 3-5
minutes with no load applied.
4. Place the MPEC Control Switch (Figure 56) to the
OFF/RESET position.
Figure 52. Main, Aux. and GFCI
Circuit Breakers (ON)
15. Observe the generator’s ammeter (Figure 53) and
verify it reads the anticipated amount of current with
respect to the load. The ammeter will only display a
current reading if a load is in use.
Figure 56. MPEC Control Switch (Off/Reset)
5. Verify that all status LEDs on the MPEC display are
OFF (not lit).
6. Remove all loads from the generator.
7. Inspect entire generator for any damage or loosening of
components that may have occurred during operation.
Figure 53. Ammeter (Load)
16. The generator will run until manually stopped or an
abnormal condition occurs.
Emergency Shutdown Procedure
1. Place the MPEC Control Switch (Figure 56) in the
OFF/RESET position.
page 36 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Maintenance
10 Hrs
DAILY
X
X
X
X
X
X
Table 14. Inspection/Maintenance
Engine
Generator
Check Engine Fluid Levels
Check Air Cleaner
Check Battery Acid Level
Check Fan Belt Condition
Check for Leaks
Check for Loosening of Parts
Replace Engine Oil and Filter * 1
Clean Air Filter
Check Fuel Filter/Water Separator Bowl
Clean Unit, Inside and Outside
Change Fuel Filter
Clean Radiator and Check Coolant Protection Level*2
Replace Air Filter Element * 3
Check all Hoses and Clamps * 4
Clean Inside of Fuel Tank
Measure Insulation Resistance Over 3M ohms
Check Rotor Rear Support Bearing
250 Hrs
500 Hrs
1000
Hrs
X
X
X
X
X
X
X
X
X
X
X
*1 Replace engine oil and filter at 100 hours, first time only.
*2 Add “Supplemental Coolant Additives (SCA’S)” to recharge the engine coolant.
*3 Replace primary air filter element when restriction indicator shows a vacuum of 625 mm (25 in. H20).
*4 If blowby hose needs to be replaced, ensure that the slope of the blowby hose is at least a 1/2 inch per foot,
with no sags or dips that could collect moisture and/or oil.
General Inspection
Prior to each use, the generator should be cleaned and
inspected for deficiencies. Check for loose, missing or
damaged nuts, bolts or other fasteners. Also check for
fuel, oil, and coolant leaks. Use Table 14 as a general
maintenance guideline. Engine Side, refer to the Engine
Instruction Manual.
Air Cleaner
Every 250 hours: Remove air cleaner element (Figure 57)
and clean the heavy duty paper element with light spray of
compressed air. Replace the air cleaner as needed.
Air Cleaner with Dust Indicator
This indicator (Figure 57) is attached to the air cleaner.
When the air cleaner element is clogged, air intake
restriction becomes greater and the dust indicator signal
shows RED meaning the element needs changing or
service. After changing the air element, press the dust
indicator button to reset the indicator.
Figure 57. Air Cleaner/Indicator
NOTICE
The air filter should not be changed until the indicator
reads “RED”. Dispose of old air filter. It may not be
cleaned or reused.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 37
Maintenance
If the engine is operating in very dusty or dry grass
conditions, a clogged air cleaner will result. This can lead to
a loss of power, excessive carbon buildup in the combustion
chamber and high fuel consumption. Change air cleaner
more frequently if these conditions exists.
Fuel Addition
Add diesel fuel (the grade may vary according to season
and locations).
Removing Water from the Fuel Tank
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally inspect the fuel
tank for water contamination and drain the contents if
required.
During cold weather, the more empty volume inside the
tank, the easier it is for water to condense. This can be
reduced by keeping the tank full with diesel fuel.
Cleaning Inside the Fuel Tank
If necessary, drain the fuel inside the fuel tank completely.
Using a spray washer (Figure 58) wash out any deposits
or debris that have accumulated inside the fuel tank.
Fuel Tank Inspection
In addition to cleaning the fuel tank, the following
components should be inspected for wear:
„„Rubber Suspension — look for signs of wear or
deformity due to contact with oil. Replace the rubber
suspension if necessary.
„„Fuel Hoses — inspect nylon and rubber hoses for signs
of wear, deterioration and hardening.
„„Fuel Tank Lining — inspect the fuel tank lining for signs
of excessive amounts of oil or other foreign matter.
Replacing Fuel Filter
„„Replace the fuel filter cartridge with new one every 500
hours or so.
„„Loosen the drain plug at the lower top of the fuel filter.
Drain the fuel in the fuel body together with the mixed
water. DO NOT spill the fuel during disassembly.
„„Vent any air
Air Removal
If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel,
or after disassembling the fuel system, bleed the system
according to the following procedure. See the ISUZU
Engine Manual for details.
To restart after running out of fuel, turn the switch to the
“ON” position for 15-30 seconds. Try again, if needed.
Figure 58. Fuel Tank Cleaning
page 38 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Maintenance
Check Oil Level
Radiator Cleaning
Check the crankcase oil level prior to each use, or when the
fuel tank is filled. Insufficient oil may cause severe damage
to the engine. Make sure the generator is level. The oil
level must be between the two notches on the dipstick as
shown in Figure 28.
The radiator (Figure 59) should be sprayed (cleaned) with
a high pressure washer when excessive amounts of dirt
and debris have accumulated on the cooling fins or tube.
When using a high pressure washer, stand at least 5 feet
(1.5 meters) away from the radiator to prevent damage to
the fins and tube.
Replacing Oil Filter
„„Remove the old oil filter.
„„Apply a film of oil to the gasket on the new oil filter.
„„Install the new oil filter.
„„After the oil cartridge has been replaced, the engine oil
will drop slightly. Run the engine for a while and check for
leaks before adding more oil if needed. Clean excessive
oil from engine.
Flushing Out Radiator and Replacing
Coolant
„„Open both cocks located at the crankcase side and at
the lower part of the radiator and drain coolant. Open
the radiator cap while draining. Remove the overflow
tank and drain.
„„Check hoses for softening and kinks. Check clamps for
signs of leakage.
Figure 59. Radiator Cleaning
Generator Storage
For long term storage of the generator the following is
recommended:
„„Tighten both cocks and replace the overflow tank.
„„Drain the fuel tank completely. Treat with a fuel stabilizer
if necessary.
„„Replace with coolant as recommended by the engine
manufacturer.
„„Completely drain the oil from the crankcase and refill if
necessary with fresh oil.
„„Close radiator cap tightly.
„„Clean the entire generator, internal and external.
„„Flush the radiator by running clean tap water through
radiator until signs of rust and dirt are removed. DO
NOT clean radiator core with any objects, such as a
screwdriver.
„„Cover the generating set and store in a clean, dry place.
WARNING
Allow engine to cool when flushing out
radiator. Flushing the radiator while hot
could cause serious burns from water or
steam.
„„Disconnect the battery.
„„Make sure engine coolant is at proper level.
„„If generator is mounted on a trailer, jack trailer up and
place on blocks so tires do not touch the ground or block
and completely remove the tires.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 39
Maintenance
Jacket Water Heater and Internal Battery
Charger 120 VAC Input Receptacles
(OPTIONAL)
This generator can be optionally equipped with two 120
VAC, 20 amp input receptacles located on the output
terminal panel.
The purpose of these receptacles is to provide power via
commercial power to the jacket water heater and internal
battery charger.
These receptacles will ONLY function when commercial
power has been supplied to them (Figure 60). To apply
commercial power to these receptacles, a power cord of
adequate size will be required (See Table 6).
When using the generator in hot climates there is no reason
to apply power to jacket water heater. However, if the
generator will be used in cold climates it is always a good
idea to apply power to the jacket water heater at all times. To
apply power to the jacket water heater simply apply power
to the jacket water heater receptacle via commercial power
using an power cord of adequate size.
If the generator will be used daily, the battery should
normally not require charging. If the generator will be idle
(not used) for long periods of time, apply power to the
battery charger receptacle via commercial power using an
power cord of adequate size.
NOTICE
To ensure adequate starting capability, always have
power applied to the generator's internal battery
charger..
Figure 60. Battery Charger & Jacket Water Heater Power Connections
page 40 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Trailer Maintenance
Trailer Maintenance
This section is intended to provide the user with generic
trailer service and maintenance information. The service
and maintenance guidelines referenced in this section refer
to a wide range of trailers.
Remember periodic inspection of the trailer will ensure safe
towing of the generator and will prevent personal injury and
damage to the equipment.
The definitions below describe some of the major
components of a typical trailer that would be used with
generator.
1. Fuel Cell — Provides an adequate amount of fuel for
the equipment in use. Fuel cells must be empty when
transporting equipment.
2. Braking System — System employed in stopping
the trailer. Typical braking systems are electric, surge,
hydraulic, hydraulic-surge and air.
3. GVWR — Gross Vehicle Weight Rating (GVWR) is
the maximum number of pounds the trailer can carry,
including the fuel cell (empty).
4. Frame Length — Measurement is from the ball hitch
to the rear bumper (reflector).
5. Frame Width — Measurement is from fender to
fender
6. Jack Stand — Trailer support device with maximum
pound requirement from the tongue of the trailer.
7. Coupler — Type of hitch used on the trailer for
towing.
8. Tire Size — Indicates the diameter of the tire in
inches (10,12,14, etc.), and the width in millimeters
(175,185,205, etc.). The tire diameter must match the
diameter of the tire rim.
9. Tire Ply — The tire ply (layers) number is rated in
letters; 2-ply, 4-ply, 6-ply, etc.
10. Wheel Hub — The wheel hub is connected to the
trailer’s axle.
11. Tire Rim — Tires mounted on a tire rim. The tire rim
must match the size of the tire.
12. Lug Nuts — Used to secure the wheel to the wheel
hub. Always use a torque wrench to tighten down
the lug nuts. See Table 18 and Figure 63 for lug nut
tightening and sequence.
13. Axle — Indicates the maximum weight the axle can
support in pounds, and the diameter of the axle
expressed in inches. Please note that some trailers
have a double axle. This will be shown as 2-6000 lbs.,
meaning two axles with a total weight capacity of 6000
pounds.
14. Suspension — Protects the trailer chassis from shocks
transmitted through the wheels. Types of suspension
used are leaf, Q-flex, and air ride.
15. Electrical — Electrical connectors (looms) are provided
with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.
16. Application — Indicates which units can be employed
on a particular trailer.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 41
Trailer Maintenance
Brakes
Hydraulic Surge Brakes
Trailer brakes should be inspected the first 200 miles of
operation. This will allow the brake shoes and drums to seat
properly. After the first 200 mile interval, inspect the brakes
every 3,000 miles. If driving over rough terrain, inspect the
brakes more frequently.
Figure 61 displays the major hydraulic surge brake
components that will require inspection and maintenance.
Please inspect these components as required using steps
1 through 8 and Table 15 as listed below:
Hydraulic surge brakes (Figure 61) should not require any
special attention with the exception of routine maintenance
such as shoe and lining replacement. Brake lines should
be periodically checked for cracks, kinks, or blockage.
Brake Adjustment
1. Place the trailer on jack stands. Make sure the jack
stands are placed on secure level ground.
2. Check the wheel and drum for free rotation.
3. Remove the adjusting hole cover from the adjusting
slot at the bottom brake backing plate.
4. With a screwdriver or standard adjusting tool, rotate
the star wheel of the adjuster assembly to expand the
brake shoes.
5. Adjust the brake shoes outward until the pressure of
the lining against the wheel drum makes the wheel
difficult to turn.
6. Adjust, rotate the star wheel in the opposite direction
until the wheel rotates freely with slight lining drag.
7. Replace the adjusting hole cover and lower the trailer
to the ground.
8. Repeat steps 1 through 7 on the remaining brakes.
Figure 61. Hydraulic Brake Components
Actuator
Hydraulic surge braking requires the installation of an
actuator at the tongue of the trailer. Remember the surge
or push of the trailer toward the tow vehicle automatically
synchronizes the trailer brakes with the tow vehicle brakes.
As the trailer pushes against the tow vehicle the actuator
telescopes together and applies force to the master
cylinder, supplying hydraulic pressure to the trailer brakes.
Periodically check and test the surge “actuator” to make sure
that it is functioning correctly. Never use an undersized actuator.
Table 15. Hydraulic Brake Troubleshooting
Symptom
Possible Cause
Solution
No Brakes
Brake line broken or kinked?
Repair or replace.
Brake lining glazed?
Reburnish or replace.
Weak Brakes or Brakes Pull to
One Side
Locking Brakes
Noisy Brakes
Dragging Brakes
Trailer overloaded?
Correct weight.
Brake drums scored or grooved?
Machine or replace.
Tire pressure correct?
Inflate all tires equally.
Tires unmatched on the same axle?
Match tires.
Brake components loose, bent or
broken?
Replace components.
Brake drums out-of-round?
Replace.
System lubricated?
Lubricate.
Brake components correct?
Replace and correct.
Brake lining thickness incorrect or
not adjusted correctly?
Install new shoes and
linings.
Enough brake fluid or correct fluid?
Replace rubber parts
fill with dot 4 fluid.
page 42 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Trailer Maintenance
Tires/Wheels/Lug Nuts
Suspension
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
The leaf suspension springs and associated components
(Figure 62) should be visually inspected every 6,000 miles
for signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts
(suspension) immediately. Torqued suspension components
as detailed in Table 17.
CAUTION
ALWAYS wear safety glasses when
removing or installing force fitted parts.
Failure to comply may result in serious
injury.
CAUTION
DO NOT attempt to repair or modify a
wheel. DO NOT install in inner tube to
correct a leak through the rim. If the rim
is cracked, the air pressure in the inner
tube may cause pieces of the rim to explode (break off)
with great force and cause serious eye or bodily injury.
Figure 62. Major Suspension Components
Tire Wear/Inflation
Tire inflation pressure is the most important factor in tire
life. Pressure should be checked cold before operation DO
NOT bleed air from tires when they are hot!. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 16 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
Table 16. Tire Wear Troubleshooting
Spring Eye Bolt
Wear Pattern
Cause
Item
Torque (Ft.-Lbs.)
3/8" U-Bolt
Min-30 Max-35
7/16" U-Bolt
Min-45 Max-60
1/2" U-Bolt
Min-45 Max-60
Shackle Bolt
Snug fit only. Parts must rotate freely.
Locking nuts or cotter pins are
provided to retain nut-bolt assembly.
Solution
Shoulder Type
Shackle Bolt
Center Wear
Over inflation.
Adjust pressure to particular
load per tire manufacturer.
Edge Wear
Under inflation.
Adjust pressure to particular
load per tire manufacturer.
Side Wear
Loss of camber
or overloading.
Make sure load does not
exceed axle rating.
Align wheels.
Toe Wear
Incorrect toe-in.
Align wheels.
Cupping
Out-of-balance.
Check bearing adjustment
and balance tires.
Wheel lockup and
tire skidding.
Avoid sudden stops when
possible and adjust brakes.
Flat Spots
Table 17. Suspension Torque Requirements
Min-30 Max-50
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 43
Trailer Maintenance
Lug Nut Torque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence (Figure 63). DO NOT
torque the wheel lug nuts all the way down. Tighten each
lug nut in 3 separate passes as defined by Table 18.
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 18. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
20-25
35-40
50-65
13"
20-25
35-40
50-65
14"
20-25
50-60
90-120
15"
20-25
50-60
90-120
16"
20-25
50-60
90-120
Figure 63. Wheel Lug Nuts
Tightening Sequence
NOTICE
NEVER use an pneumatic air gun to tighten wheel
lug nuts.
page 44 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Trailer Wiring Diagram
Figure 64. Trailer/Towing Vehicle Wiring Diagram
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 45
Generator Wiring Diagram
Figure 65. Generator Wiring Diagram
page 46 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Engine Wiring Diagram
Figure 66. Engine Wiring Diagram
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 47
controller Wiring Diagram
Figure 67. Controller Wiring Diagram
page 48 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Troubleshooting (Generator)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, use Table 19 shown below for diagnosis of the Generator. If the problem cannot be remedied, consult our
company’s business office or service plant.
Symptom
No Voltage Output
Low Voltage Output
High Voltage Output
Circuit Breaker Tripped
Table 19. Generator Troubleshooting
Possible Problem
Solution
AC Voltmeter defective?
Check output voltage using a voltmeter.
Is wiring connection loose?
Check wiring and repair.
Is AVR defective?
Replace if necessary.
Defective Rotating Rectifier? Check and replace.
Defective Exciter Field?
Check for approximately 17.3 ohms across J & K on CN1
Is engine speed correct?
Turn engine throttle lever to “High”.
Is wiring connections loose? Check wiring and repair.
Defective AVR?
Replace if necessary.
Is wiring connections loose? Check wiring and repair.
Defective AVR?
Replace if necessary.
Short Circuit in load?
Check load and repair.
Over current?
Confirm load requirements and reduce.
Defective circuit breaker?
Check and replace.
Over current Relay actuated? Confirm load requirement and replace.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 49
Troubleshooting (Diagnostic lamp)
The engine controller of this generator diagnoses problems
that arise from the engine control system and the engine
itself. Press the diagnostic button (Figure 68) on the
diagnostic panel to determine if an engine malfunction has
occurred.
Figure 68. Diagnostic Panel
Method of Operation
1. Normally, the diagnostic lamp will be dimly lit when
the MPEC Control Switch is placed in the MANUAL
position.
2. If engine trouble occurs, the diagnostic lamp will be
brightly lit as long as the control switch is left in the
manual position.
3. The diagnostic lamp will indicate that an engine
malfunction has occurred.
NOTICE
For a complete understanding of error codes and
troubleshooting procedures, refer to the enclosed
engine instruction manual.
NOTICE
If the engine is cranked while the diagnostic switch is in
the “ON” position, the engine will not be stopped even if
the starter switch is turned to the “OFF” position. In such
case, turn the diagnostic switch to the “OFF” position.
page 50 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Notes
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 51
Explanation of Code in Remarks Column
The following section explains the different symbols and
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice. Multiquip
does not guarantee the availability of the parts listed.
Sample partS liSt
NO.
1
2%
2%
3
4
part NO. part Name
QtY. remarKS
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
12347
WASHER, 3/8 IN....1 .....MQ-45T ONLY
12348
HOSE ..................A/R ...MAKE LOCALLY
12349
BEARING ..............1 .....S/N 2345B AND ABOVE
NO. Column
QtY. Column
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
remarKS Column
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
Unique Symbols — All items with same unique
symbol
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Duplicate item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
part NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“make/Obtain locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items. Examples include battery cables, shims,
and certain washers and nuts.
“Not Sold Separately” — Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
page 52 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Suggested Spare Parts
dca125USi3CAN WHISPERWATT GENERATOR with
ISUZU 4HK1X DIESEL engine
1 to 3 units
Qty.P/N
Description
5............1132402322...........CARTRIDGE, oil filter
3............0602046684...........ELEMENT, AIR (outer)
3............P777639................ELEMENT, AIR (inner)
1............8980627130...........BELT, FAN
3............m3310502603........radiator hose, upper
3............m3310502703........radiator hose, lower
3............8980714010...........fuel filter, feed pump
3............8981430410...........filter fuel, element main
3............8980742880...........filter fuel, element pre
1............0602122272...........UNIT, OIL PRESSURE
1............0602123260...........UNIT, WATER TEMPERATURE
1............9095720140...........PACKING, WATER TEMPERATURE
1............8121468300...........SEnsor, water temperature
1............8980274560...........SEnsor, OIL pressure
1............1096300850...........gasket, oil pressure sensor
1............8971256011...........SWITCH, OVERHEAT
1............0601870440...........circuit breaker, 1p, 20 amp
1............0601870441...........circuit breaker 2p, 50 amp
1............0601820602...........automatic Voltage Regulator
3............0601806671...........fuse, 15 amp
1............0601806644...........fuse, 30 amp
1............0601806640...........fuse, 65 amp
2............ly2DUS12VDC.....relay
NOTICE
Part number on this Suggested Spare Parts list may
supersede/replace the P/N shown in the text pages of
this book.
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 53
GENERATOR ASSY.
page 54 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
GENERATOR ASSY.
NO. PART NO.
1
C0110001002
1-1#
1-2#8131070013
1-3# 8131611014
1-4# 8131015003
1-5# 0012112035
1-6# 0042612000
1-7# 8101026013
1-8#0601821349
1-9# 0601822601
1-10# 8001020004
1-11# 8001020504
1-12# 012210020
1-13# 0040010000
1-14# 0601000209
1-15#0071906312
2
C0130000503
30845041804
4
8131315202
5
8101350013
6
0012110060
7
0042610000
8
031110160
9
0010112035
10 0040012000
11
031112230
128131310104
13
8131312204
14
8131331003
15
0105050616
16
8101333003
17 0010006030
18
0040006000
19
952404470
20
M3163400503
21
0010310075
22
030210250
23
012010030
24
M3163600003
25
012010030
26
012010030
27
8131332014
280600815000
29
0605000063
30
0030016000
30A 0040016000
PART NAME
QTY. REMARKS
ROTOR ASSY...............................1........INCLUDES ITEMS W/#
FIELD ASSY
1
FAN
1
COUPLING DISK
8
BALANCING PLATE......................1........PURCHASE ITEM 1-14 AS A SET
HEX HEAD BOLT
10
WASHER, LOCK
10
SET PLATE, RECTIFIER..............1........PURCHASE ITEM 1-14 AS A SET
RECTIFIER
2
SURGE ABSORBER
1
WASHER, INSULATOR
1
WASHER, INSULATOR
1
HEX HEAD BOLT
4
WASHER, LOCK
4
BALANCING WEIGHT KIT
1
BEARING
1
STARTER ASSY
1
GROMMET
2
END BRACKET
1
FIELD ASSY, EXCITER
1
HEX HEAD BOLT
4
WASHER, LOCK
4
WASHER, FLAT
4
HEX HEAD BOLT
6
WASHER, LOCK
6
WASHER, FLAT
6
COVER,BEARING
1
GASKET, BEARING
1
COVER, END BRACKET
1
HEX HEAD BOLT
10
COVER, END BRACKET
1
HEX HEAD BOLT
2
WASHER, LOCK
2
WASHER, FLAT
2
COUPLING RING
1
HEX HEAD BOLT
8
WASHER, LOCK
8
HEX HEAD BOLT
12
COUPLING ADAPTER
1
HEX HEAD BOLT
12
HEX HEAD BOLT
12
COVER, FAN
1
NUT
1
RUBBER SUSPENSION
2
HEX NUT
2
WASHER, LOCK
2
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 55
control box ASSY.
page 56 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
control box ASSY.
NO. PART NO.
PART NAME
QTY.
REMARKS
1
M3213001802
CONTROL BOX
1
1-10330000210
EDGING
2
1-20330000280
EDGING
1
1-30330000340
EDGING
2
2
0601808827
CIRCUIT BREAKER, 3P 350A
1
2-1
0342604120
HEX SOCKET HEAD CAP SCREW
6
3
0021006080
MACHINE SCREW
4
4
0601823863
RELAY UNIT
2
5
7538070
MACHINE SCREW......................................4.................REPLACES P/N 0027104016
6
0601820602
AUTOMATIC VOLTAGE REGULATOR
1
7
0027105016
MACHINE SCREW
4
8
0601801124
CURRENT TRANSFORMER
3
9
011206020
HEX HEAD BOLT 6X20................................6.................REPLACES P/N 0027106020
10
0601820847
OVER CURRENT RELAY
1
11
0601820848
OVER CURRENT RELAY
1
12
7538070
MACHINE SCREW......................................2.................REPLACES P/N 0027104016
12A OEMAA8
HEX NUT......................................................2.................REPLACES P/N 0207004000
13
0601802218
HOLDER, FUSE
1
13A 0601806671
FUSE, 15A
3
14
0027103016
MACHINE SCREW
2
150601815153
TERMINAL
1
16
0027104020
MACHINE SCREW
2
17
8121468300
SENSOR, INLET AIR TEMP.........................1.................REPLACES P/N 0603210240
18
M3260500503
SET PANEL, ELECTRIC PARTS
1
19
0016906016
HEX HEAD BOLT
4
208980710280
CONTROLLER.............................................1.................REPLACES P/N 0602202686
21M3260500604 BRACKET
1
22
0016906016
HEX HEAD BOLT
4
23
0601831205
PUSH BUTTON SWITCH
1
24
0601831330
DIAGNOSTIC SWITCH
1
25
0016906016
HEX HEAD BOLT
4
260601821370
RECTIFIER..................................................1.................REPLACES P/N 0601823240
27
0027104030
MACHINE SCREW
1
28
ly2DUS12VDCRELAY..........................................................2.................REPLACES P/N 0601827656
28APTF08A
BASE............................................................2.................REPLACES P/N 0601823109
28BPYCA1
CLIP.............................................................4.................REPLACES P/N 0601824400
29
0027104020
MACHINE SCREW
4
30
8972177780
SENSOR, BAROMETRIC PRESSURE.......1.................REPLACES P/N 0602130220
31
7538070
MACHINE SCREW......................................2.................REPLACES P/N 0027104016
32
5825530444
RELAY, STARTER........................................1.................REPLACES P/N 0602201402
33
0027106016
MACHINE SCREW
2
345825500290
RELAY..........................................................3.................REPLACES P/N 0602201400
35
0027105016
MACHINE SCREW
3
36
8970119490
RELAY, GLOW PLUG...................................1.................REPLACES P/N 0602202685
37
0027105016
MACHINE SCREW
2
38
M3213500704
CONTROL BOX COVER
1
39
0016906016
HEX HEAD BOLT
8
40
M3270100504
SELECTOR SWITCH 1
40A M3550002504
DECAL: SELECTOR SWITCH NUMBER 1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 57
control box ASSY. ( continued)
page 58 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
control box ASSY. (continued)
NO. PART NO.
40B M3550002604
41
M3213602704
42
M3213602804
43
0027104035
43A OEMAA8
44
7538070
44A OEMAA8
45
0016906016
46
M3213602604
46-1 0317700180
47
M3213602504
48
0016906016
49
011008020
49A 0040508000
50
M3223001203
51
0601807641
52
0601808988
53
0601801040
54
0601806859
55
0601801041
56
0601840073
570601840100
58
0602202641
59
0027104040
59A OEMAA8
6082608
61
0602103092
61A 0601810245
620602120095
63
0602122093
64
0602123092
65
0602121081
66
0602125090
67
9826800370
68
0601831330
69
0601831395
70M1223100004
71M3223100004
72
0027105010
73
0027105010
74
M9220100004
75
0080200007
76
0602122272
77M9200100004
788943998582
79
0602123267
809095720140
81
0602120465
82
0601806644
83
0601806640
PART NAME
QTY.
REMARKS
DECAL: SELECTOR SWITCH NUMBER 1
SWITCH BRACKET
1
SWITCH BRACKET
1
MACHINE SCREW
4
HEX NUT
4
MACHINE SCREW......................................4.................REPLACES P/N 0027104016
HEX NUT 4
HEX HEAD BOLT
4
SWITCH COVER
1
WEATHER STRIP
1
SWITCH COVER
1
HEX HEAD BOLT
10
HEX HEAD BOLT........................................10................REPLACES P/N 0019208020
TOOTHED WASHER
1
CONTROL PANEL
1
FREQUENCY METER, 45~65Hz 240V 1
AC AMMETER, 0~200A/400A:5A
1
CHANGE OVER SWITCH, AMMETER 1
AC VOLTMETER, 0~600V
1
CHANGE OVER SWITCH, VOLTMETER 1
RHEOSTAT (VR), 2W 1K OHM
1
KNOB...........................................................1.................REPLACES P/N 0601840121
CONTROLLER, ECU (CAN77)
1
MACHINE SCREW
2
HEX NUT
2
SWITCH.......................................................1.................REPLACES P/N 0601831340
ALARM LAMP
3
BULB, DC 18V
3
TACHOMETER
1
OIL PRESSURE GAUGE
1
WATER TEMPERATURE GAUGE
1
CHARGING AMMETER
1
FUEL GAUGE
1
PANEL LIGHT..............................................1.................REPLACES P/N 0601810141
SWITCH, PANEL LIGHT
1
SWITCH, ENGINE SPEED
1
STOPPER
1
STOPPER
1
MACHINE SCREW
4
MACHINE SCREW
4
SET SCREW
2
SNAP RING
2
UNIT, OIL PRESSURE
1
ADAPTER
1
ADAPTER....................................................1.................REPLACES P/N 0602020220
UNIT, WATER TEMPERATURE
1
PACKING......................................................1.................REPLACES P/N 0602021109
PICK UP, TACHOMETER
1
FUSE, 30A
1
FUSE, 65A
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 59
control box ASSY. ( continued)
page 60 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
control box ASSY. (continued)
NO.
84
85
86
87
PART NO.
0601830762
M3246703004
M3357202002
M3357201802
PART NAME
SWITCH, FUEL PUMP
WIRE HARNESS. GENERATOR
WIRE HARNESS, ENGINE
WIRE HARNESS, CONTROLLER
QTY.
1
1
1
1
REMARKS
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 61
ENGINE AND RADIATOR ASSY.
page 62 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
ENGINE AND RADIATOR ASSY.
NO. PART NO.
1
M3923200144
1A
8980627130
2
M3303200603
3
0105091025
4
0040010000
5
060500060
6
0030012000
7
0040012000
8M3923200114
8-10602011029
9M9200100904
100150000016
11
M3310202904
12
011008020
13
M3310202803
13A M3493114104
14
0016910025
15
0016910025
16
M3310202104
17
011008020
18
M3310502603
19
M3310502703
20
0605515148
21
M3310600303
22
0016906016
23
M3310600204
23A 0222100260
24
011206020
25
M3310203003
25A0601850239
26
0016910025
27
M1924200004
28
0016910025
29
0602046258
29A 0602046684
29B P777639
30
0602040650
31
M3373200204
32
011008020
33
0602040596
34
011008020
35
020108060
36
M3373101203
37
M3373101103
38
M3326100140
39
0605515146
PART NAME
QTY.
REMARKS
ENGINE, ISUZU 4HK1X
1
FAN BELT.....................................................1.................REPLACES P/N 0602015253
ENGINE FOOT
2
HEX HEAD BOLT.........................................8.................REPLACES P/N 0105091025
WASHER, LOCK
8
RUBBER SUSPENSION
2
HEX NUT
2
WASHER, LOCK
2
RADIATOR
1
CAP
1
PLUG
1
O-RING
1
RADIATOR BRACKET
2
HEX HEAD BOLT.........................................8.................REPLACES P/N 0019208020
RADIATOR BRACKET
1
ACOUSTIC SHEET
1
HEX HEAD BOLT
6
HEX HEAD BOLT
4
RADIATOR BRACKET
1
HEX HEAD BOLT.........................................2.................REPLACES P/N 0019208020
RADIATOR HOSE, UPPER
1
RADIATOR HOSE, LOWER
1
HOSE BAND
1
HOSE SUPPORT
1
HEX HEAD BOLT
4
HOSE BRACKET
2
RUBBER SEAL
2
HEX HEAD BOLT.........................................2.................REPLACES P/N 0016906020
FAN BRACKET
1
GROMMET
1
HEX HEAD BOLT
4
FAN MOTOR
2
HEX HEAD BOLT
8
AIR CLEANER
1
ELEMENT, AIR CLEANER, OUTER
1
ELEMENT, AIR CLEANER, INNER..............1.................REPLACES P/N 0602046685
INDICATOR, AIR CLEANER
1
BRACKET AIR CLEANER
1
HEX HEAD BOLT.........................................2.................REPLACES P/N 0019208020
BAND, AIR CLEANER
2
HEX HEAD BOLT.........................................4.................REPLACES P/N 0019208020
HEX NUT......................................................4.................REPLACES P/N 020108060
HOSE, AIR CLEANER
1
HOSE, AIR CLEANER
1
BLOW BY PIPE
1
HOSE BAND
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 63
ENGINE AND RADIATOR ASSY. (continued)
page 64 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
ENGINE AND RADIATOR ASSY. (continued)
NO. PART NO.
40
0605515197
41
M3373100903
42
0605515197
43
0191701050
44
0605515149
45
M9100000204
46
0602021731
47
7812014003B
480802011104
490150000018
50
011206020
51
0199102250
52
0605515170
530602022581
54
0602022561
550603306590
560603300285
570605511395
58
0603306395
590602021070
60
0269200800
61
M3323500004
62
0016910025
63
8973243861
63A 1132402322
64
0010110120
64A 0040010000
64B 031110160
65
0010110150
65A 0040010000
65B 031110160
660602022530
67
0602022930
680379001250
69
0605515198
70
0802081003C
71
0802010900
72
M3316100303
73
011008020
740199102100
750193600700
760193601000
77
0605515170
78M3923200124
78A M3490202004
79
0132004000
PART NAME
QTY.
REMARKS
HOSE BAND
3
AIR DUCT HOSE
1
HOSE BAND
1
BLOW BY HOSE
1
HOSE BAND
2
HOSE JOINT
1
SEAL WASHER
1
DRAIN JOINT...............................................1.................REPLACES P/N M2320300103
PLUG............................................................1.................REPLACES P/N M9200200004
O-RING
1
HEX HEAD BOLT.........................................2.................REPLACES P/N 0016906020
DRAIN HOSE
1
HOSE BAND................................................2.................REPLACES P/N 0605515106
ADAPTER
1
90 DEGREE ELBOW
1
CONNECTOR
1
LOCKNUT
1
VALVE
1
HOSE JOINT
1
CAP
1
DRAIN HOSE
1
BRACKET, OIL FILTER
1
HEX HEAD BOLT
2
OIL FILTER...................................................1.................REPLACES P/N 0602041007
CARTRIDGE, OIL FILTER...........................1.................REPLACES P/N 0602041221
HEX HEAD BOLT
2
WASHER, LOCK
2
WASHER, FLAT...........................................2.................REPLACES P/N 0041210000
HEX HEAD BOLT
2
WASHER, LOCK
2
WASHER, FLAT...........................................2.................REPLACES P/N 0041210000
ADAPTER
4
HOSE JOINT
4
HOSE
2
HOSE BAND
4
RESERVE TANK, 5L....................................1.................REPLACES P/N M9300000203
CAP, RESERVE TANK..................................1.................REPLACES P/N 0602010900
BRACKET, RESERVE TANK
1
HEX HEAD BOLT.........................................3.................REPLACES P/N 0019208020
HOSE
1
HOSE
1
HOSE
1
HOSE BAND................................................3.................REPLACES P/N 0605515106
INTERCOOLER
1
ACOUSTIC SHEET
1
PLUG, 3/8
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 65
ENGINE AND RADIATOR ASSY. (continued)
page 66 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
ENGINE AND RADIATOR ASSY. (continued)
NO.
80
80A
81
82
83
84
85
86
87
88
88A
89
90
91
92
93
94
95
96
97
98
100
101
102
103
PART NO.
M3310202603
M3493114504
012210020
0016906016
M3310502803
M3310502903
0605515208
0605515204
0605515207
M3310600404
0228900320
011206020
M3310303803
M3310303903
011206020
M3310304104
0016906016
M3310304003
011206020
M3326200204
011008020
8121468300
8980274560
1096300850
8971256011
PART NAME
QTY.
REMARKS
BRACKET, INTER COOLER
1
ACOUSTIC SHEET
2
HEX HEAD BOLT.........................................8.................REPLACES P/N 0017110020
HEX HEAD BOLT
12
COOLER HOSE
1
COOLER HOSE
1
HOSE BAND
2
HOSE BAND
1
HOSE BAND
1
HOSE BRACKET
1
RUBBER SEAL
1
HEX HEAD BOLT.........................................1.................REPLACES P/N 0016906020
FAN SHROUD
1
FAN SHROUD
1
HEX HEAD BOLT.........................................8.................REPLACES P/N 0016906020
BRACKET, FAN SHROUD
1
HEX HEAD BOLT
8
FAN GUARD
1
HEX HEAD BOLT.........................................6.................REPLACES P/N 0016906020
BLOWBY HOSE BRACKET
1
HEX HEAD BOLT.........................................1.................REPLACES P/N 0019208020
SENSOR, WATER TEMPERATURE
1
SENSOR, OIL PRESSURE
1
GASKET, SENSOR OIL PRESSURE
1
SWITCH, OVERHEAT
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 67
OUTPUT TERMINAL ASSY.
page 68 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
OUTPUT TERMINAL ASSY.
NO. PART NO.
1
M3230700003
2
M9220100304
3
0801830804
4
0039316000
5
0040016000
6
0401450160
7
0012108035
8
M3236100803
9
M3236100404
100605010040
11
0027103010
11A 0207003000
11B 58413
12
0027103010
12A 0207003000
13
M9220100804
13A 0040006000
13B 952404470
13C 0080200005
14
0016906016
15
M3236400004
16
M3236300004
17
011206020
18
0601815194
19
7538070
20
0603306775
21
7538070
22
0601870440
23
0601870441
24
M1260700504
24-1 0222100100
25
011206020
26
0601812597
27
0601811034
28
7538070
28A OEMAA8
29M3236400204
30
0016906016
31
M3236100213
32
012212045
33
031112230
34
0805009804
35
0030012000
36M4236100604
37M4236400304
38
0016906016
39
0019208020
39A 0040508000
PART NAME
QTY.
REMARKS
TERMINAL BOARD
1
OUTPUT TERMINAL BOLT
5
TIE BOLT......................................................5.................REPLACES P/N M9220100404
HEX NUT
10
WASHER, LOCK
15
WASHER, FLAT..........................................20................REPLACES P/N 0041416000
HEX HEAD BOLT.........................................5.................REPLACES P/N 0016908035
TERMINAL COVER
1
OUTPUT WINDOW
1
HINGE
2
MACHINE SCREW
4
HEX NUT......................................................4.................REPLACES P/N 0030003000
WASHER, FLAT
4
REPLACES P/N 0041203000
MACHINE SCREW
4
HEX NUT......................................................4.................REPLACES P/N 0030003000
SET SCREW
2
WASHER, LOCK
2
WASHER, FLAT...........................................2.................REPLACES P/N 0041206000
RETAINING RING
2
HEX HEAD BOLT
4
CABLE, OUTLET COVER
1
SUPPORTER, CABLE OUTLET COVER 1
HEX HEAD BOLT.........................................6.................REPLACES P/N 0016906020
TERMINAL BLOCK
1
MACHINE SCREW......................................2.................REPLACES P/N 0027104016
BLIND PLUG
2
MACHINE SCREW......................................4.................REPLACES P/N 0027104016
CIRCUIT BREAKER, 1P 20A
2
CIRCUIT BREAKER, 2P 50A
3
BREAKER, FITTING COVER
1
CUSHION RUBBER
2
HEX HEAD BOLT.........................................2.................REPLACES P/N 0016906020
RECEPTACLE, GF530EM 125V 20Ax2.......2.................REPLACES P/N 0601812598
RECEPTACLE, CS6369 250V 50A..............3.................REPLACES P/N 0601812538
MACHINE SCREW.....................................10................REPLACES P/N 0027104016
HEX NUT 10
COVER
1
HEX HEAD BOLT
8
TERMINAL COVER
1
HEX HEAD BOLT.........................................2.................REPLACES P/N 012212045
WASHER, FLAT
2
STAY RUBBER.............................................2.................REPLACES P/N M9310200004
HEX NUT
2
COVER
1
BRACKET
1
HEX HEAD BOLT
2
HEX HEAD BOLT
1
TOOTHED WASHER
2
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 69
BATTERY ASSY.
page 70 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
BATTERY ASSY.
NO. PART NO.
10602220198
2
M9310500404
3
M9103000504
4
0602220921
5
M3346901604
6
M3346901504
7
8
0016910025
8A
0040510000
9
0016910025
9A
0040508000
PART NAME
QTY.
REMARKS
BATTERY
1
BATTERY SHEET
1
BATTERY BAND
1
BATTERY BOLT SET
2
BATTERY CABLE
1
BATTERY CABLE
1
CABLE..........................................................1.................MAKE LOCALLY
HEX HEAD BOLT
1
TOOTHED WASHER
1
HEX HEAD BOLT
1
TOOTHED WASHER114
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 71
Muffler Assy.
page 72 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
Muffler Assy.
NO. PART NO.
1M3330101002
2
012212030
3
M3333001603
41141451840
5M3333200304
6
0039308000
7
0017110050
8M3330401104
9M3330401003
10
011008020
11
0602326061
PART NAME
QTY.
REMARKS
MUFFLER
1
HEX HEAD BOLT.........................................4.................REPLACES P/N 0017112030
EXHAUST PIPE
1
GASKET.......................................................1.................REPLACES P/N 0602320108
GASKET
1
HEX NUT
8
HEX HEAD BOLT
4
COVER
1
BRACKET
1
HEX HEAD BOLT.........................................4.................REPLACES P/N 0019208020
U-BOLT SET
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 73
FUEL TANK ASSY.
page 74 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
FUEL TANK ASSY.
NO. PART NO.
1
M3364000203
1-1
06055050702
1-2
0605501074
1-2A0605516090
3
M3364200003
4
0016910025
5
0016910030
6
M2367700003
7
0605515225
8
011008020
9
0207008000
10
0222101000
11
0191302200
12
0605515109
13
M3366700203
14
011008020
15
8980139861
15A 8981430410
16
8980758551
16A 8980742880
17
8973834270
18
1096750951
191096300860
20
0015310045
20A 004001000
20B 031110160
21
0010110080
21A 0040010000
21B 031110160
22
8980682750
22A 8980714010
23
011606025
24
0191301790
25
0191300800
26
0191300230
27
0191300850
28
0191300750
29
0605515109
30
0602022791
31
0602022778
32
M3364400004
33
M2484600003
33A M2494600004
340603306792
35
0343708008
35A 0605516091
PART NAME
QTY.
REMARKS
FUEL TANK
1
FUEL TANK CAP
1
FUEL SENDER UNIT
1
GASKET
1
FUEL TANK BRACKET
2
HEX HEAD BOLT
4
HEX HEAD BOLT 4
FUEL FILLER HOSE
1
HOSE BAND
2
HEX HEAD BOLT.........................................8.................REPLACES P/N 0019208020
HEX NUT
8
TANK SHEET
6
VENT HOSE
1
HOSE BAND
2
FUEL FILTER BRACKET
1
HEX HEAD BOLT.........................................4.................REPLACES P/N 0019208020
FUEL FILTER (MAIN)...................................1.................REPLACES P/N 0602042426
ELEMENT, FUEL FILTER.............................1.................REPLACES P/N 8980088400
FUEL FILTER (PRE.)...................................1.................REPLACES P/N 8980758550
ELEMENT, FUEL FILTER.............................1.................REPLACES P/N 8980758540
JOINT PIPE..................................................4.................REPLACES P/N 0602042661
JOINT BOLT.................................................4.................REPLACES P/N 0602042621
PACKING......................................................8.................REPLACES P/N 0602042641
HEX HEAD BOLT
4
SPRING WASHER
4
PLAIN WASHER
2
HEX HEAD BOLT
2
WASHER, LOCK
2
WASHER, FLAT...........................................2.................REPLACES P/N 0041210000
FUEL FEED PUMP......................................1.................REPLACES P/N 0602023240
FUEL FILTER...............................................1.................REPLACES P/N 0602042517
HEX HEAD BOLT.........................................2.................REPLACES P/N 0016906025
SUCTION HOSE
1
SUCTION HOSE
1
SUCTION HOSE
1
SUCTION HOSE
1
RETURN HOSE
1
HOSE BAND
10
HOSE JOINT
2
HOSE JOINT
2
PICKUP TUBE
2
FUEL FILLER BRACKET
1
ACOUSTIC SHEET
1
PLUG
1
HEX HEAD BOLT
5
SEALING WASHER
5
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 75
ENCLOSURE ASSY. PART 1.
page 76 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
ENCLOSURE ASSY. PART1.
NO. PART NO.
1M3413002502
2
M3363300303
3
0016910030
4
0603306797
5
M3423002802
5A
M3493114403
6
M3423002902
6A
M3493114403
70601851765
8
011008020
9
M3423003003
10
011008020
11
0016910025
12
M3310400403
13
011206020
14
M3310400304
15
011206020
16M3423500204
17
011008020
18
M3423200704
19
011206020
20
M3310302704
21
0016906016
22
M3423300304
22A M3493113704
23
011008020
24
M3423202603
24A M3493111803
25
M3423202403
26
0019206016
27
011008020
28
011008020
29
M3433001402
29A M3493201304
30
0010114040
30A 515455840
30B 030214350
30C 0041220000
31
0010120050
31A 0030020000
31B 030220510
31C 0041220000
32
M3463101503
32A M3493509204
PART NAME
QTY.
REMARKS
BASE
1
ENVIRONMENTAL TANK
1
HEX HEAD BOLT
12
PLUG, 1-1/2
1
FRONT FRAME
1
ACOUSTIC SHEET
1
FRONT FRAME
1
ACOUSTIC SHEET
1
GROMMET
1
HEX HEAD BOLT........................................27................REPLACES P/N 0019208020
FRONT FRAME
1
HEX HEAD BOLT.........................................8.................REPLACES P/N 0019208020
HEX HEAD BOLT
6
HOSE COVER
1
HEX HEAD BOLT.........................................7.................REPLACES P/N 0016906020
HOSE COVER
1
HEX HEAD BOLT.........................................8.................REPLACES P/N 0016906020
BRACKET
1
HEX HEAD BOLT.........................................2.................REPLACES P/N 0019208020
DUCT COVER
2
HEX HEAD BOLT........................................14................REPLACES P/N 0016906020
SHROUD BRACKET
1
HEX HEAD BOLT
6
DISCHARGE GUIDE
1
ACOUSTIC SHEET
1
HEX HEAD BOLT.........................................4.................REPLACES P/N 0019208020
COVER FRONT FRAME
1
ACOUSTIC SHEET
1
FRONT LOUVER
1
HEX HEAD BOLT
6
HEX HEAD BOLT.........................................4.................REPLACES P/N 0019208020
HEX HEAD BOLT.........................................4.................REPLACES P/N 0019208020
CENTER FRAME
1
ACOUSTIC SHEET
1
HEX HEAD BOLT
4
HEX NUT......................................................4.................REPLACES P/N 0030014000
WASHER, LOCK..........................................4.................REPLACES P/N 0040014000
WASHER, FLAT
8
HEX HEAD BOLT
4
HEX NUT
4
WASHER, LOCK..........................................4.................REPLACES P/N 0040020000
WASHER, FLAT
8
ROOF PANEL
1
ACOUSTIC SHEET
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 77
ENCLOSURE ASSY. PART 1 (continued)
page 78 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
ENCLOSURE ASSY. PART 1 (continued)
NO. PART NO.
33
M3463202202
33A M3493509303
34
M3463201104
35
0016906016
36M3463202303
36A M3493506004
37
011008020
38
M3423202704
38A M3493108004
39
011008020
40
0017110025
41
M3310600004
42
011008020
43
011008020
43A 0040508000
44
0605503062
45M1414800104
46
011008020
470603306793
PART NAME
QTY.
REMARKS
ROOF PANEL
1
ACOUSTIC SHEET
1
BACK PLATE
2
HEX HEAD BOLT
12
DUCT
1
ACOUSTIC SHEET
1
HEX HEAD BOLT.........................................8.................REPLACES P/N 0019208020
OVER COVER, FRONT FRAME
1
ACOUSTIC SHEET
1
HEX HEAD BOLT........................................51................REPLACES P/N 0019208020
HEX HEAD BOLT.........................................8.................REPLACES P/N 0019210025
COVER, RADIATOR CAP
1
HEX HEAD BOLT.........................................4.................REPLACES P/N 0019208020
HEX HEAD BOLT.........................................1.................REPLACES P/N 0019208020
TOOTHED WASHER
1
FUEL LEAK DETECTED SWITCH
1
BRACKET
1
HEX HEAD BOLT.........................................2.................REPLACES P/N 0019208020
PLUG
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 79
ENCLOSURE ASSY. PART 2.
page 80 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
ENCLOSURE ASSY. PART 2.
NO. PART NO.
1
M3443001902
1A
M3493308603
2M3443002004
3
011008020
4
M3443400103
4A
M3493308904
4-1
0314501550
4-20330000250
4-30330000325
5
011008020
6M3443002103
6A
M3493308804
7M3443002203
7A
M3443008804
8
011008020
9
011008020
10
0016910025
11
M3443301803
11A M3493308704
12
011008020
13
011008020
14
M3443200803
15
M3443600304
16
0207306000
16A 952404470
17
B9114000002
18
0021806016
18A 020106050
19M9110100204
20M9116100004
21
011008020
22
M3453201702
22A M3493426704
23
0019104065
23A 0042308000
23B 0042408000
24
0016910025
25
M3453005303
25A M3493426504
26
M3453005403
26A M3493426504
27
M3453002703
27A M3493417204
28
M3453005503
28A M3493426604
PART NAME
QTY.
REMARKS
REAR FRAME
1
ACOUSTIC SHEET
1
DUCT
2
HEX HEAD BOLT............................................6.................. REPLACES P/N 0019208020
PANEL, REAR FRAME
1
ACOUSTIC SHEET
1
RUBBER SEAL
1
EDGING
1
EDGING
1
HEX HEAD BOLT............................................6.................. REPLACES P/N 0019208020
DUCT
1
ACOUSTIC SHEET
1
DUCT
1
ACOUSTIC SHEET
1
HEX HEAD BOLT............................................6.................. REPLACES P/N 0019208020
HEX HEAD BOLT............................................6.................. REPLACES P/N 0019208020
HEX HEAD BOLT
4
COVER, REAR FRAME
1
ACOUSTIC SHEET
2
HEX HEAD BOLT............................................4.................. REPLACES P/N 0019208020
HEX HEAD BOLT............................................4.................. REPLACES P/N 0019208020
DOOR, REAR FRAME
1
WINDOW PLATE
1
HEX NUT
8
WASHER, FLAT
8
DOOR HANDLE ASSY...................................1.................. REPLACES P/N M9113000002
MACHINE SCREW
4
HEX NUT........................................................4.................. REPLACES P/N 0030006000
HINGE
2
WASHER
2
HEX HEAD BOLT............................................3.................. REPLACES P/N 0019208020
SPLASHER PANEL
1
ACOUSTIC SHEET
1
HEX HEAD BOLT
4
WASHER, LOCK
4
WASHER, FLAT
4
HEX HEAD BOLT
2
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 81
ENCLOSURE ASSY. PART 2 (continued)
page 82 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
ENCLOSURE ASSY. PART 2 (continued)
NO. PART NO.
29
B9114000002
29A C9312500004
30
0021806016
30A 020106050
310845046904
320845047004
33M9116100004
34
011008020
350601850097
36
0027208025
37M9310000004
38
0600800320
39
0021806016
40
M3454100003
40A M3494405904
41
0019108065
41A 0042308000
41B 031108160
42
0016910025
PART NAME
QTY.
REMARKS
DOOR HANDLE ASSY................................4.................REPLACES P/N M9113000002
SEAL RUBBER
4
MACHINE SCREW
16
HEX NUT.....................................................16................REPLACES P/N 0030006000
HINGE..........................................................6.................REPLACES P/N M9110100804
HINGE..........................................................5.................REPLACES P/N M9110100904
WASHER
11
HEX HEAD BOLT........................................26................REPLACES P/N 0019208020
STOPPER
8
MACHINE SCREW
8
CAP
13
MANUAL PACK
1
MACHINE SCREW
4
SIDE PANEL
1
ACOUSTIC SHEET
1
HEX HEAD BOLT
4
SPRING WASHER
4
PLAIN WASHER
4
HEX HEAD BOLT
2
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 83
RUBBER SEALS ASSY.
page 84 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
RUBBER SEALS ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
PART NO.
0229200870
0229201130
0229201240
0228901070
0314502700
0229200125
0228901165
0228900925
0228901105
0228900565
0228900945
0228900505
0229201090
0229201335
0228901335
0228900655
0229201090
0228100630
0229401080
0228800565
0228801080
0228800545
0228100370
0228100640
0228900700
0228900640
0229200295
0229200220
PART NAME
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
QTY.
1
1
3
1
1
4
3
4
3
1
4
1
1
2
1
1
1
2
1
1
1
1
2
2
1
1
2
2
REMArks
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 85
NAMEPLATE AND DECALS ASSY.
8 - 11A
3 - 6A
9-2
9-2A
9-6
9-6A
2 - 9A
9-6A
9-6
A
3-4A
10
1-3
9-2A
9-2
A
9-2A
4-6A
9-2
4-6
4-6
4-3A
8-1
4-1A
DECAL KIT
4-9
4-8A
11
4-4
TRAILER
4-7A
9-1
6-1A
3-7A
DECAL KIT
9-1A
3-4A
5-3A
9-3
1-1
1-1A
1-1A
2-8A
1-2A
8-9A
8-9
9-7 12
9-7A
9-3A
9-5A
9-5
8-12A
page 86 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
NAMEPLATE AND DECALS ASSY.
NO. PART NO.
1-1
M3550003003
1-1A EE57081
1-2
M9520100304
1-2A#
1-3
M9520100603
1-3A#
2-1
M3550003503
2-2
M3550003603
2-3
M9520000104
2-4
M9520000204
2-5
M9520000804
2-6
M9520000904
2-7
M9520001104
2-8
M9520100004
2-8A#
2-9
M9520100204
2-9A#
2-10 M9520200404
3-1
M9500000004
3-2
M9500100004
3-3
M9500100304
3-4
M9503000004
3-4A#
3-5
M9503000103
3-6
M9503100004
3-6A#
3-7
M9510100004
3-7A#
4-1
EE57066
4-1A EE57067
4-2
M1550002203
4-3
EE57082
4-3A EE57083
4-4
M9520000004
4-5
M9520000504
4-6
M9520100004
4-6A#
4-7
M9520100404
4-7A# 4-8
M9520100503
4-8A#
4-9
M9520200003
5-1
M9500300004
5-2
M9500300104
5-3
M9510100403
5-3A#
PART NAME
QTY.
REMARKS
DECAL : OPERATING PROCEDURES (ENGLISH) ................. 1............ M35000300A
DECAL : OPERATING PROCEDURES (FRENCH)
1
DECAL : SAFETY INSTRUCTIONS (ENGLISH)....................... 1............ M92010030
DECAL : SAFETY INSTRUCTIONS (FRENCH)........................1............B92110040CE
DECAL : CAUTION, START/STOP (ENGLISH)......................... 2............ M92010060
DECAL : CAUTION, START/STOP (FRENCH).......................... 1............ MQC92210000CE
DECAL : CONTROL PANEL...................................................... 1............ M35000350
DECAL : OPERATING PANEL................................................... 1............ M35000360
PLATE : AMMETER CHANGE- OVER SWITCH....................... 1............ M92000010
PLATE : VOLTMETER CHANGE- OVER SWITCH.................... 1............ M92000020
DECAL : AC............................................................................... 1............ M92000080
DECAL : DIAGNOSTIC SWITCH.............................................. 1............ M92000090
DECAL : DIAGNOSTIC BUTTON.............................................. 1............ M92000110
DECAL : WARNING, ELECTRIC SHOCK HAZ. (ENGLISH)..... 1............ M92010000
DECAL : WARNING, ELECTRICAL SHOCK HAZ.(FRENCH).. 1............ MQB9310050CE
DECAL : CAUTION, STOP ENGINE (ENGLISH).......................1............ M92010020A
DECAL : CAUTION, STOP ENGINE (FRENCH)....................... 1............M92010020CE
DECAL : OVER CURRENT RELAY........................................... 1............ M92020040
DECAL : OIL DRAIN PLUG....................................................... 1............ M90000000
DECAL : WATER........................................................................ 1............ M90010000
DECAL : INTER-COOLER DRAIN............................................. 1............ M90010030
DECAL : WARNING, MOVING PARTS (ENGLISH)................... 2............ M90300000
DECAL : WARNING, MOVING PARTS (FRENCH)....................2............M90300000CE
DECAL : WATER - OIL CHECK................................................ 1............ M90300010
DECAL : WARNING, HOT COOLANT (ENGLISH).................... 1............ M90310000
DECAL : WARNING, HOT COOLANT (FRENCH)..................... 1............ M9031000CE
DECAL : CAUTION, HOT PARTS (ENGLISH)........................... 1............ M91010000
DECAL : CAUTION, HOT PARTS (FRENCH)............................ 1............ MQB90400030CE
DECAL : NOTICE, 50 AMP RECEPTACLES (ENGLISH)
.1
DECAL : NOTICE, 50 AMP RECEPTACLES (FRENCH)
1
DECAL : RECEPTACLE & CIRCUIT BREAKER....................... 1............ M15000220
DECAL : NOTICE, LOAD SHARING (ENGLISH)...................... 1............ M35000000
DECAL : NOTICE, LOAD SHARING (FRENCH)
1
DECAL : GROUND.................................................................... 1............ M92000000
DECAL : START CONTACT....................................................... 1............ M92000050
DECAL : WARNING, ELECTRIC SHOCK HAZ. (ENGLISH)..... 1............ M92010000
DECAL : WARNING, ELECTRICAL SHOCK HAZ.(FRENCH).. 1............ MQB9310050CE
DECAL : DANGER, HIGH VOLTAGE (ENGLISH)...................... 1............ M92010040
DECAL : DANGER, HIGH VOLTAGE (FRENCH)....................... 1............ MQS-2731CE
DECAL : WARNING, ELECTRICAL (ENGLISH)........................1............ M92010050
DECAL : WARNING, ELECTRICAL (FRENCH)........................ 1............ M92010050CE
DECAL : OUTPUT TERMINAL.................................................. 1............ M92020000
DECAL : -
1
M90030000
DECAL : +.................................................................................. 1............ M90030010
DECAL : CAUTION, OFF/RESET SW (ENGLISH).....................1............ M91010040
DECAL : CAUTION, OFF/RESET SW (FRENCH)..................... 1............ MQC90530000CE
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 87
NAMEPLATE AND DECALS ASSY. (continued)
8 - 11A
3 - 6A
9-2
9-2A
9-6
9-6A
2 - 9A
9-6A
9-6
A
3-4A
10
1-3
9-2A
9-2
A
9-2A
4-6A
9-2
4-6
4-6
4-3A
8-1
4-1A
DECAL KIT
4-9
4-8A
11
4-4
TRAILER
4-7A
9-1
6-1A
3-7A
DECAL KIT
9-1A
3-4A
5-3A
9-3
1-1
1-1A
1-1A
2-8A
1-2A
8-9A
8-9
9-7 12
9-7A
9-3A
9-5A
9-5
8-12A
page 88 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
NAMEPLATE AND DECALS ASSY. (continued)
NO. PART NO.
PART NAME
QTY.
REMARKS
6-1
M9503200004
DECAL : WARNING, ENGINE EXHAUST (ENGLISH).............. 1............ M90320000
6-1A#
DECAL : WARNING, ENGINE EXHAUST (FRENCH)............... 1............ MQB90420000CE
7-1
M9500500004
DECAL : DIESEL FUEL............................................................. 1............ M90050000
7-2
M9510000004
DECAL : FUEL DRAIN PLUG.................................................... 1............ M91000000
8-1
M9512200004
DECAL : MQ.............................................................................. 1............ M91220000
8-2
M9510200304
DECAL : MQ POWER
2
8-3M3560102004 STRIPE
2
8-4
M3560102103
STRIPE : WHISPERWATT
2
8-5M3560102204 STRIPE
2
8-6
M3560102303
STRIPE : 125
1
8-7
M3560102403
STRIPE : 125
1
8-8M3560102504 STRIPE
2
8-9
EE57068
DECAL: NOTICE, ENVIRONMENTAL WARNING (ENGLISH).. 1
8-9A EE57069
DECAL: NOTICE, ENVIRONMENTAL WARNING (FRENCH) 1
8-10 0600500092
PLATE : MQ POWER
1
8-10A 0021106016
MACHINE SCREW
4
8-11 M3550002204
DECAL : CAUTION, BAIL MAX CAPACITY (ENGLISH)............ 1............ M35000220
8-11A# DECAL : CAUTION, BAIL MAX CAPACITY (FRENCH) 1
8-12 M9503200104
DECAL : DANGER, EXHAUST GAS (ENGLISH)...................... 1............ M90320010
8-12A#
DECAL : DANGER, EXHAUST GAS (FRENCH)....................... 1............ M90320010CE
8-13 M9510000104
DECAL : DOCUMENT BOX LOCATED..................................... 1............ M91000010
9-1
49002
DECAL: WARNING, TRAILER (ENGLISH)
1
9-1A#
DECAL: WARNING, TRAILER (FRENCH)................................ 1............ 490002CE
9-2$ EE57072
DECAL: NOTICE, BONDED TO FRAME (ENGLISH)
2
9-2A$ EE57073
DECAL: NOTICE, BONDED TO FRAME (FRENCH)
2
9-3$ EE57075
DECAL: NOTICE, CLASS F (ENGLISH)
1
9-3A$ EE57076
DECAL: NOTICE, CLASS F (FRENCH)
1
9-5$ EE57070
DECAL: NOTICE, OVERLOAD (ENGLISH)
1
9-5A$ EE57071
DECAL: NOTICE, OVERLOAD (FRENCH)
1
9-6$ EE57079
DECAL: NOTICE, SUPPLY WIRES (ENGLISH)
1
9-6A$ EE57080
DECAL: NOTICE, SUPPLY WIRES (FRENCH)
1
9-7
920214100
DECAL: WARNING, SPARKS (ENGLISH)
1
9-7A#
DECAL: WARNING, SPARKS (FRENCH)................................. 1............ M9042000CE
10
EE52657
DECAL KIT (FRENCH).............................................................. 1............ INCLUDES ITEMSW/ #
11
EE57074
DECAL KIT (ENGLISH & FRENCH).......................................... 1............ INCLUDES ITEMSW/ $
12
EE57090
NAME PLATE, EMISSION CONTROL (ENGLISH & FRENCH) 1
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 89
Terms and Conditions of Sale — Parts
paYmeNt termS
5.
Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
6.
The following items are not returnable:
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
a.
SpeCIal expeDItINg ServICe
Terms of payment for parts are net 30 days.
FreIght polICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
b.
mINImUm orDer
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
retUrNeD gooDS polICY
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
1.
A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
2.
Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
c.
Any line item with an extended
dealer net price of less than
$5.00.
d.
Special order items.
e.
Electrical components.
f.
Paint, chemicals, and lubricants.
g.
Decals and paper products.
h.
Items purchased in kits.
7.
The sender will be notified of any material
received that is not acceptable.
To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
8.
Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
a.
The parts numbers and descriptions
must match the current parts price
list.
9.
b.
The list must be typed or computer
generated.
Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
c.
The list must state the reason(s)
for the return.
d.
The list must reference the sales
order(s) or invoice (s) under
which the items were originally
purchased.
e.
The list must include the name
and phone number of the person
requesting the RMA.
3.
A copy of the Return Material Authorization
must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
lImItatIoNS oF Seller’S lIaBIlItY
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
lImItatIoN oF WarraNtIeS
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
Effective: February 22, 2006
11. Credit issued will be applied to future
purchases only.
prICINg aND reBateS
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
page 90 — DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13)
notes
DCA125USI3CAN 60 hz Generator • operation and parts manual — rev. #2 (09/24/13) — page 91
Operation and Parts Manual
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
United StateS
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
Contact: mq@multiquip.com
MQ Parts Department
Tel. (800) 421-1244
Fax (310) 537-3927
Service Department
800-421-1244
310-537-3700
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
Fax: 310-537-4259
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
Fax: 310-943-2238
mexico
United Kingdom
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Unit 2, Northpoint Industrial Estate,
Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: sales@multiquip.co.uk
Tel: 0161 339 2223
Fax: 0161 339 3226
Canada
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2013, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the MQ Power logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUsT accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is: