DeWalt 36-485 Instruction manual

with 30" Unifence®
(Model 36-477)
with 30" Biesemeyer®
(Model 36-485)
REVISED 6-15-00
PART NO. 422-19-651-0045
Copyright © 2000 Delta Machinery
INSTRUCTION MANUAL
Platinum Edition
10" Contractor’s Saw
SAFETY RULES
Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain
hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result.
Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection can reduce
your potential for injury. But even the best guard won’t make up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop. If a procedure feels dangerous, don’t try it. Figure out an alternative procedure
that feels safer. REMEMBER: Your personal safety is your responsibility.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not be modified
and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product.
Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 505 Southgate Drive, Guelph, Ontario N1H 6M7)
WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL
INJURY
ance at all times.
16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools
sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
17. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters, etc.
18. USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by Delta
may cause hazards or risk of injury to persons.
19. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in “OFF” position before plugging in power cord.
20. NEVER STAND ON TOOL. Serious injury could occur
if the tool is tipped or if the cutting tool is accidentally contacted.
21. CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate properly
and perform its intended function – check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged
should be properly repaired or replaced.
22. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter
only.
23. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.
24. DRUGS, ALCOHOL, MEDICATION. Do not operate
tool while under the influence of drugs, alcohol or any
medication.
25. MAKE SURE TOOL IS DISCONNECTED FROM
POWER SUPPLY while motor is being mounted, connected or re-connected.
26. WARNING: The dust generated by certain woods
and wood products can be injurious to your health.
Always operate machinery in well ventilated areas and
provide for proper dust removal. Use wood dust collection systems whenever possible.
27. WHEN THE UNIT IS NOT IN USE the switch should
be locked in the “OFF” position to prevent unauthorized
use.
1. FOR YOUR OWN SAFETY, READ INSTRUCTION
MANUAL BEFORE OPERATING THE TOOL. Learn the
tool’s application and limitations as well as the specific
hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION.
4. GROUND ALL TOOLS. If tool is equipped with threeprong plug, it should be plugged into a three-hole electrical receptacle. If an adapter is used to accommodate a
two-prong receptacle, the adapter plug must be attached
to a known ground. Never remove the third prong.
5. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it “on.”
6. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
7. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations, or
expose them to rain. Keep work area well-lighted.
8. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from
work area.
9. MAKE WORKSHOP CHILDPROOF – with padlocks,
master switches, or by removing starter keys.
10. DON’T FORCE TOOL. It will do the job better and be
safer at the rate for which it was designed.
11. USE RIGHT TOOL. Don’t force tool or attachment to
do a job for which it was not designed.
12. WEAR PROPER APPAREL. No loose clothing,
gloves, neckties, rings, bracelets, or other jewelry to get
caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.
13. ALWAYS USE SAFETY GLASSES. Wear
safety
glasses. Everyday eyeglasses only have impact resistant
lenses; they are not safety glasses. Also use face or dust
mask if cutting operation is dusty. These safety glasses
must conform to ANSI Z87.1 requirements. Note:
Approved glasses have Z87 printed or stamped on them.
14. SECURE WORK. Use clamps or a vise to hold work
when practical. It’s safer than using your hand and frees
both hands to operate tool.
15. DON’T OVERREACH. Keep proper footing and bal2
28. WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well-ventilated area, and work with approved safety equipment such as those dust masks
that are specially designed to filter out microscopic particles.
SAVE THESE INSTRUCTIONS
ADDITIONAL SAFETY RULES FOR CIRCULAR SAWS
1. ALWAYS use blade guard and splitter with antikickback for every operation for which it can be used,
including “thru-sawing” operations. Thru-sawing operations are those when the blade cuts completely through the
workpiece as in ripping or cross-cutting.
2. ALWAYS hold the work firmly against the miter gage
or fence.
3. ALWAYS use a push stick for ripping narrow stock.
Refer to ripping applications in instruction manual where
the push stick is covered in detail. See push stick pattern
included in this instruction manual.
4. NEVER perform any operation “free-hand” which
means using your hands to support or guide the workpiece. Always use either the fence or miter gage to position and guide the work.
5. NEVER stand or have any part of your body in line
with the path of the saw blade. KEEP your hands out of
the line of the saw blade.
6. NEVER reach behind or over the cutting tool with
either hand for any reason.
7. MOVE the rip fence out of the way when crosscutting.
8. NEVER use the fence as a cut-off gage when crosscutting.
9. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction or rotation of the blade or
cutter only.
10. WHEN cutting moulding, NEVER run the stock between the fence and the moulding cutterhead.
11. NEVER attempt to free a stalled saw blade without
first turning the saw OFF. Turn off switch immediately to
prevent motor damage.
12. THE USE of attachments and accessories not
recommended by Delta may result in risk of injuries.
13. PROVIDE adequate support to the rear and sides of
the saw table for wide or long workpieces.
14. AVOID kickbacks (work thrown back toward you) by:
A. Keeping blade sharp.
B. Keeping rip fence parallel to the saw blade.
C. Keeping splitter and anti-kickback fingers and
guard in place and operating.
D. Not releasing the work before it is pushed all the
way past the saw blade.
E. Not ripping work that is twisted or warped or
does not have a straight edge to guide along
the fence.
15. AVOID awkward operations and hand positions
where a sudden slip could cause your hand to move into
the cutting tool.
16. NEVER use solvents to clean plastic parts. Solvents
could possibly dissolve or otherwise damage the material.
Only a soft, damp cloth should be used to clean plastic
parts.
17. PERMANENTLY mount the saw to a supporting surface before performing any cutting operations.
18. NEVER cut metals or material which may make
hazardous dust.
19. ALWAYS. use in a well-ventilated area. Remove sawdust frequently. Clean out sawdust from the interior of the
saw to prevent a potential fire hazard.
20. DO NOT expose your saw to rain or use in a damp
location.
21. ADDITIONAL INFORMATION regarding the safe
and proper operation of this product is available from the
National Safety Council, 1121 Spring Lake Drive, Itasca,
IL 60143-3201, in the Accident Prevention Manual for
Industrial Operations and also in the Safety Data Sheets
provided by the NSC. Please also refer to the American
National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations.
22. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others.
FOREWORD
Delta 10 Contractor’s Saws are designed to give high quality performance with maximum depth of cut capacity up to
3-1/8 at 90° and 2-1/8 at 45° for clean cutting of standard stock sizes. Delta Model 36-477 includes a 30 Unifence
T-Slot rail fence system and Model 36-485 includes a 30 Biesemeyer T-Square home shop fence system. These Delta
Models come equiped with; basic machine, sturdy steel stand, integral dust chute, patented Auto-Set T-Slot miter
gage, heavy duty motor, large on/off paddle switch, cast extension wing and table, convenient up-front blade raising
and tilting controls and 10 carbide blade.
3
UNPACKING AND CLEANING
Carefully unpack the table saw and all loose items from the shipping containers. Remove the protective coating
from the machined surfaces of the saw. This coating may be removed with a soft cloth moistened with kerosene
(do not use acetone, gasoline or lacquer thinner for this purpose). Fig. 2, illustrates the components of the table
saw. Fig. 3, illustrates the components of the saw stand. Fig. 4, illustrates the components of the Unifence® Fig. 5,
6 and 7 illustrates the components of the Biesemeyer Fence.
1
2
3
4
16
21
20
5
19
17
18
15
13
14
9
6
11
12
7
10
8
Fig. 2
1. Contractor’s Saw
12. 5/16-18 x 5/8 Carriage Head Screw
2. Blade Tilting Handwheel
13. 5/16 Flat Washer
3. Handwheel Lock Knob
14. 5/16-18 Hex Nut
4. Blade Guard and Splitter Assembly
15. Arbor Wrenches (2)
5. Table Insert
16. Cast Iron Extension Table
6. Miter Gage
17. 7/16-20 x 1-3/4 Hex Head Screws
for assembling extension table (3)
7. Miter Gage Handle
18. Flat Washers for assembling
extension wing (3)
8. Miter Gage Handle Cap
9. Splitter Mounting Bracket
19. 1/4-20 x 3/4 Flat head Screw
10. 1/4-20 x 3/4 Hex Head Screws (2)
20. Flat Washer
11. 1/4 Flat Washers (2)
21. Hex Nut
4
3
1
2
4
5
7
23
8
6
22
9
11
10
13
12
15
14
16
18
21
17
19
20
Fig. 3
UNIFENCE T-SLOT RAIL FENCE SYSTEM
7
3
6
5
4
8 9
10
15
11
12
14
2
19
13
16
21
18
20
1
Fig. 4
5
17
1. Combination Dust Chute/
Support Panel
2. Motor Pulley
3. Motor
4. Pulley Guard
5. Drive Belt
6. Spring
7. Pins (2) for Mounting Motor
8. Motor Mounting Plate
9. Lockwashers (4)
10. Flat Washers (4)
11. 5/16-18 x 3/4 Carriage
Head Screws (4)
12. Hex Nuts (4)
13. 5/16 Hex Nuts (8)
14. 5/16 Lockwashers (8)
15. 5/16 Flat Washers
16. 5/16-18 x 5/8 Hex Head
Screws (8)
17. Rubber Feet (4)
18. #10-32 x 12 Screws (8)
19. #10 Keps Nuts (8)
20. #10-1/2 Sheet Metal
Screws (3)
21. Grommet
22. Front Leg Panel
23. Rear Leg Panel
1. Unifence Body
2. Fence
3. Shelf Support Bracket
4. Front Table Support
5. Table Board
6. Table Legs (2)
7. Front T-Slot Guide Rail
8. Leg Adapter (2)
9. Nuts and Flat Washers (2)
10. Leveling Screws (2)
11. Z-Brackets (3)
12. 7/16-20 x 3/4 Hex Head
Screws, Lockwashers,
and Flat Washers (3 ea.)
13. U-Bolts (2)
14. Angle Brackets (3)
15. 1/4-20 x 3/4 Carriage Head
Screws, Flat Washers, and
1/4-20 Hex Nuts (3 ea.)
16. Flat Washers and 1/4-20
Hex Nuts for U-Bolts (4 ea.)
17. #8 x 13/16 Hex Washer
Head Screws (14)
18. 3/8-24 x 1 Hex Head Bolts
Flat Washers, and Hex Nuts
(2 ea.)
19. 1/4-20 Hex Head Bolt, Flat
Washer and Hex Nut (1 ea.)
20. Guide Rail End Caps (2 ea.)
21. Unifence Flip Stop
BIESEMEYER T-SQUARE FENCE SYSTEM
The T-Square® Commercial Fence System includes the fence assembly, front rail, rear rail, front
guide tube and right extension table Model 78-927 for 30 capacity.
IMPORTANT: The T-Square® Fence System is designed to be used ONLY with a supporting
extension table.
UNPACKING
Carefully unpack the T-Square® fence system from the shipping carton(s). Figure 5, 6 & 7
illustrates all the items supplied with the 78-904 fence system.
1 - Rear Rail
for fastening front and rear rails
to right extension table
2 - Front Rail
16 - 1-1/2 long flat head Phillips screws (8)
3 - Guide Tube
17 - 1-1/4 O.D. Flat Washers (6)
4 - T-Square® Fence Assembly
18 - 1/4-20 hex nuts (8)
5 - Template for aligning front rail to saw table
19 - Extension Table
for fastening guide tube to front rail
for fastening extension table legs
6 - 1/4-20 x 1/2 long hex head screws (7)
20 - Legs (2)
7 - Lock washers (7)
21 - 5/8 long wood screws #8 (8)
22 - 1/4-20 x 1-1/2 long flat head
Phillips screws (4)
for fastening rear rail to saw table and sheet metal
extension wing if applicable
23 - 1/4 flat washers (4)
8 - 3/8-24 x 1-1/4 long hex head cap screws (2)
24 - 1/4-20 hex nuts (4)
9 - 7/8 O.D. flat washers (2)
10 - Lock washers (2)
NOTE: A common hardware package is used
for several different models, therefore you may
have leftover hardware.
11 - 3/8-24 hex nuts (2)
for fastening front rail to saw table
12 - 3/8-16 x 1-1/4 long flat head screws (2)
13 - 7/8 O.D. flat washers (2)
14 - Lock washers (2)
15 - 3/8-16 hex nuts (2)
6
8
9
10
11
12
13
14
15
1
4
6
2
7
5
Fig. 5
19
16
17
18
Fig. 6
7
3
20
22
23
24
21
Fig. 7
8
ASSEMBLY INSTRUCTIONS
B
C
E
ASSEMBLING SAW STAND
1. Assemble the dust chute and support panel (A)
Fig. 8, to the inside of the front stand panel (B) with three
#10 x 1/2 sheet metal screws (C), four #10-32 x 1/2
screws (D), and four hex nuts (E). Fig. 9 illustrates the
dust chute and support panel (A) assembled to the front
of stand (B). NOTE: The front stand panel will have the
saw identity labels facing you. Do not completely tighten the stand hardware at this time. Also, make certain
the dust chute/support panel (A) Fig. 9, is located under
the lip of front stand panel (B).
D
A
Fig. 8
B
A
Fig. 9
2. Assemble the other end of dust chute and support
panel (A) Fig. 10, to rear stand panel (F) as shown with
four #10-32 x 1/2 screws and hex nuts, three of which
are shown at (D). NOTE: Do not completely tighten stand
hardware at this time.
F
D
D
Fig. 10
9
A
ASSEMBLING
SAW TO STAND
F
1. Fig. 11, illustrates the stand (B) completely assembled.
2. Assemble rubber foot (A) Fig. 11, onto the end of
each stand leg (B). Insert grommet (C) into hole (D) in
stand leg.
D
B
E
3. Carefully place saw (E) Fig. 12, onto saw stand (B).
Align eight holes in the top of stand (B) with mounting
holes in the bottom of saw (E) and fasten with eight
screws, flat washers, lockwashers, and hex nuts (F) Fig.
11.
A
C
Fig. 11
4. Fig. 12, illustrates the saw (E) assembled to the saw
stand (B). Carefully push down on the top of the saw
until the stand legs are positioned firmly on the floor surface and securely tighten all saw and stand mounting
hardware. Notice that panel (G) is not only a support for
a stand, but also serves as a dust chute.
E
B
G
Fig. 12
A
D
C
B
ASSEMBLING BLADE
TILTING HANDWHEEL
1. Assemble blade tilting handwheel (A) Fig. 13, to
shaft (B). Make certain slot (C) in handwheel is engaged
with roll pin (D) on the shaft.
Fig. 13
2. Thread locking lever (E) Fig. 14, onto shaft.
A
3. Fig. 14, illustrates the blade tilting handwheel (A)
and locking lever (E) assembled to the saw.
E
10
Fig. 14
MOTOR
The motor shipped with your saw is a 1-1/2 H.P., Ball Bearing, Capacitor Start/Capacitor Run, 115/230
Volt motor.
This motor has been specially selected to best supply power to your machine and the relative safety
of the machine is enhanced by its use. We, therefore, strongly suggest that only this motor be used,
as the use of other motors may be detrimental to the performance and safety of the saw.
ASSEMBLING MOTOR TO
MOTOR MOUNTING PLATE
WARNING: WHEN ASSEMBLING THE MOTOR TO
THE MOTOR MOUNTING PLATE, MAKE CERTAIN THE
S AW I S D I S C O N N E C T E D F R O M T H E P O W E R
SOURCE.
C
1. Assemble the motor (A) to the motor mounting plate
(B) as shown in Fig. 15, using four carriage bolts, flat
washers, star washers, and hex nuts (C).
B
NOTE: Do not completely tighten the hex nuts at this
time.
A
Fig. 15
ASSEMBLING MOTOR
AND MOTOR MOUNTING
PLATE TO SAW
A
WARNING: WHEN ASSEMBLING THE MOTOR AND
MOTOR MOUNTING PLATE TO THE SAW, MAKE
CER-TAIN THE SAW IS DISCONNECTED FROM THE
POWER SOURCE.
X
Y
B
1. Insert two pins (X) Fig. 16, into holes (D) in each side
of bracket (B). Assemble spring (Y) onto ends of pins as
shown.
X
D
2. Position motor and motor mounting plate (A) Fig. 17,
below bracket (B) to allow bracket arm to slide through
large opening in motor mounting plate (A).
Fig. 16
3. Depress plungers (C) Fig. 17, on both sides of
brack-et (B) and rotate motor mounting plate (A) until
plungers (C) are engaged in holes (D) Fig. 16, of motor
mounting plate (A).
4. Fig. 18, illustrates the motor and motor mounting
plate assembled to the rear of the saw.
C
B
C
A
Fig. 17
11
Fig. 18
ASSEMBLING MOTOR
PULLEY, BELT AND
PULLEY GUARD, AND
DRIVE BELT
B
WARNING: WHEN ASSEMBLING MOTOR PULLEY,
BELT AND PULLEY GUARD, AND DRIVE BELT, MAKE
CERTAIN THE MOTOR IS DISCONNECTED FROM
THE POWER SOURCE.
A
C
1. Remove the motor shaft key that is taped to the
motor.
Fig. 19
2. Insert the key (A) Fig. 19, in the keyway on the motor
shaft. Assemble the motor pulley (B) on the motor shaft
as shown, with the hub of the pulley facing out. Tighten
set screw (C) against key (A) in motor shaft.
E
3. Remove wing nut and external tooth lockwasher (D)
Fig. 20, and outer cover (E) from belt and pulley guard (G).
G
D
Fig. 20
4. Slide the belt and pulley guard bracket (G) Fig. 21,
between the motor plate (M) and motor mounting plate
(L), as shown.
G
L
Fig. 21
5. Position belt and pulley guard bracket (G) Fig. 22, so
the motor pulley (B) is centered and through the hole in
the belt and pulley guard bracket, as shown. Tighten the
four hex nuts that fasten the motor to the motor mounting plate.
6. Using a straight edge, align the motor pulley with the
arbor pulley. If necessary, adjust the motor pulley (B)
Fig. 22, in or out on the motor shaft.
B
G
12
Fig. 22
M
7. Lift the motor and assemble the drive belt (H) Fig.
23, to the arbor pulley and motor pulley (B). The weight
of the motor will provide the correct belt tension.
H
B
Fig. 23
8. WARNING: IMMEDIATELY AFTER ASSEMBLING
THE BELT, RAISE THE SAW BLADE TO ITS MAXIMUM
HEIGHT AND TILT THE SAW BLADE TO 45 DEGREES.
CHECK TO SEE IF THE MOTOR (J) FIG. 24, IS BELOW
THE TOP OF THE TABLE SURFACE (K). IF THE
MOTOR (J) IS ABOVE THE TOP OF THE TABLE SURFACE, THE MOTOR MUST BE MOVED TO THE LEFT
UNTIL YOU ARE CERTAIN THE END BELL (J) OF THE
MOTOR IS BELOW THE TOP OF THE TABLE SURFACE. THEN RE-ALIGN THE MOTOR PULLEY TO THE
ARBOR PULLEY.
J
K
Fig. 24
9. Assemble the outer cover (E) Fig. 25, of the belt and
pulley guard assembly, which was removed in STEP 3,
and fasten with external tooth lockwasher and wing nut
(D). IMPORTANT: Make certain the outer cover does not
interfere with the drive belt and the motor pulley.
D
E
Fig. 25
CONNECTING MOTOR CORD
TO SWITCH ASSEMBLY
C
WARNING: BEFORE CONNECTING MOTOR CORD TO
THE SWITCH ASSEMBLY, MAKE CERTAIN THE SAW
IS DISCONNECTED FROM THE POWER SOURCE.
B
1. Insert the pronged motor plug (A) Fig. 26, into the
female receptacle (B) of switch-to-motor cord (C).
A
13
Fig. 26
2. Fig. 27, illustrates the motor cord connected to the
switch assembly.
Fig. 27
ASSEMBLING
BLADE GUARD AND
SPLITTER ASSEMBLY
A
B
WARNING: MAKE CERTAIN THE SAW IS DISCONNECTED FROM THE POWER SOURCE.
1. Fasten the rear splitter mounting bracket (A) Fig. 28,
to the rear trunnion using the two 3/4 hex head screws
(B) and flat washers. Do not completely tighten the two
screws (B) at this time.
2. With wrenches supplied, remove the saw blade from
the saw. Refer to section “CHANGING THE SAW BLADE”
of this manual. Raise saw arbor to its highest position.
Fig. 28
3. Remove screw and large washer (C) Fig. 29, from
the inside splitter mounting bracket.
C
Fig. 29
4. Using a straight edge, check to see if the top and
bottom of the inside splitter bracket (D) Fig. 30, is
aligned with the inner arbor flange (E), as shown.
D
E
Fig. 30
14
5. If an alignment is necessary, loosen the two screws
(F) Fig. 31, align bracket (D) with the arbor flange (E) and
tighten screws (F).
D
6. Loosely assemble large washer and screw (C) Fig. 31,
to the inside splitter bracket. This screw and washer was
removed in STEP 3.
F
C
E
Fig. 31
7. Assemble the blade guard and splitter assembly (G)
Fig. 32, between the large washer (C) and the splitter
bracket and tighten screw (H) with wrench supplied.
G
H
C
Fig. 32
G
8. Fasten the rear of the blade guard and splitter bracket
assembly (G) Fig. 33, to the rear splitter mounting
bracket using 5/8 carriage bolt (J), flat washer, and hex
nut. IMPORTANT: The splitter (G) Fig. 33, has a notch (L)
cut in the top edge as shown. This feature will enable the
blade guard to stay in the raised position to make blade
changing a little easier. Simply raise the front of blade
guard (M) Fig. 34, until the rear edge of the blade guard
slips into notch (L) of splitter (G); the blade guard will
stay in this position.
L
J
Fig. 33
M
L
G
Fig. 34
15
9. With the blade guard (L) Fig. 35, in the raised position, assemble the saw blade (K) on the saw arbor with
two arbor wrenches supplied.
L
K
Fig. 35
G
10. Using a straight edge, check to see if the saw blade
is aligned with the rear of the splitter (G), as shown in
Figs. 36 and 37. If alignment is necessary, loosen the
screws (A) Fig. 37, align splitter (G) with the saw blade,
and tighten two screws (A).
Fig. 36
G
A
Fig. 37
11. Lower saw blade and install table insert (P) Fig. 38,
in the saw table as shown. IMPORTANT: When installing
the table insert, always make certain to hold on to the
blade guard (L). The insert will automatically release the
holding action on the splitter and lower the blade guard
when it is installed in the table opening.
L
P
16
Fig. 38
ASSEMBLING
EXTENSION WING
1. Assemble extension wing (A) Fig. 39, to the saw
table using three 7/16-20 x 1-1/4 screws (B) and lockwashers (C) as shown in Fig. 39.
C
B
D
A
Fig. 39
2. With a straight edge (D) Fig. 39, make certain the
extension wing (A) is level with the saw table before
tightening three screws (B) Fig. 40.
B
Fig. 40
ASSEMBLING SWITCH
TO EXTENSION WING
C
B
1. Assemble switch (A) Fig. 41, behind the lip of extension wing (B) with 1/4-20 x 3/4 flat head screw (C), flat
washer, and locknut.
A
Fig. 41
2. Fig. 42, illustrates the switch assembled to the
extension wing.
17
Fig. 42
ASSEMBLING TABLE
MOUNTING BRACKETS
TO SAW TABLE
1. Assemble Z-brackets (A) Fig. 43, to the three tapped
holes at the inside edge on the right side of saw table
(B), using three 7/16-20 x 3/4 hex head screws (C) with
flat washers and lockwashers.
C
B
A
Fig. 43
2. Using a square (D) Fig. 44, make certain the
Z-brackets (A) are perpendicular to the saw table as
shown. Also, lift upward on Z-brackets (A) while tightening screws (C) to eliminate any play.
D
A
A
Fig. 44
3. Fig. 45, illustrates the Z-brackets assembled to the
saw table.
4. Assemble angle bracket (E) Fig. 46, onto Z-bracket
(A) using 1/4-20 x 3/4 carriage bolt (F) with flat washer
and hex nut. IMPORTANT: The longer leg of angle
bracket (E) must be secured to Z-bracket (A). Assemble
the remaining two angle brackets to the edge of the
table in the same manner.
5. Using a square (G) Fig. 47, set the angle brackets so
they are approximately 3/4 from the top of the saw
table. Final adjustments to angle brackets will be made
later.
Fig. 45
G
F
A
E
E
F
E
Fig. 46
18
Fig. 47
UNIFENCE ASSEMBLY INSTRUCTIONS
ASSEMBLING TABLE LEGS AND FRONT TABLE SUPPORT
Fig. 48
1. The table board supplied will require thirteen locations to be marked on the bottom of the table board at
the locations illustrated in Fig. 48. NOTE: The table
board should be positioned so that the edge with no
veneer is on the side that will be attached to the extension wing. Turn the table board upside-down with the
raw edge to the left for leg hardware mounting.
A
B
2. Assemble table leg (A) Fig. 49, to table board (B) using
four #8 x 7/8 long wood screws (C) as shown. Assemble
remaining table leg to the table in the same manner.
CAUTION: DO NOT OVER-TIGHTEN LEG MOUNTING
SCREWS. Over-tightening screws in particle board may
cause them to strip.
C
Fig. 49
E
3. Fasten front table support (D) Fig. 50, to the bottom
of table using two 7/8 long wood screws (E) as shown.
CAUTION: DO NOT OVER-TIGHTEN SCREWS (E).
Over-tightening screws in particle board may cause them
to strip. Do not completely tighten the two screws (E) at
this time, as adjustment is necessary.
D
E
19
Fig. 50
4. Insert foot adapter (T) Fig. 51, into the bottom of each leg (A). Assemble the 3/8 jam nut (V)
Fig. 51, approximately 3/4 of the way onto leveling screw (W) and place a flat washer (X) on the leveling screw. Thread the leveling screw (W) Fig. 51, into foot adapter. Fig. 52, illustrates the foot leveling
assembly on the table leg. Assemble the remaining foot assembly to the other table leg in the same
manner. NOTE: Height adjustments can be made later.
Fig. 51
Fig. 52
5. Assemble shelf support bracket (M) Fig. 53, to the
table legs (A) using two U-clamps (N), flat washers, and
hex nuts (P). NOTE: Height adjustments to the bracket
can be made later.
N
M
N
P
Fig. 53
20
ASSEMBLING UNIFENCE
TABLE TO SAW
B
A
1. Position table board (A) Fig. 54, onto angle brackets
(B).
B
Fig. 54
2. While holding table board firmly against the saw
table, fasten table to three angle brackets (B) Fig. 55,
using three #8 x 7/8 long wood screws (C). CAUTION:
DO
NOT OVER-TIGHTEN
TABLE MOUNTING
SCREWS. Over-tightening screws in particle board may
cause them to strip.
C
C
B
A
B
Fig. 55
D
F
A
3. Using a straight edge (D) Fig. 56, make certain the
surface of the Unifence table (A) is level with the saw
table (F) by adjusting the height of the two leveling
screws (E) Fig. 57, at the base of the table legs and
adjusting the height of angle brackets (B) Fig. 58 and
tighten hex nuts (G). Position hex nuts (H) Fig. 57,
against the bottom of the table legs to hold the leveling
screws in position and tighten. Make sure the Unifence
table is level with the saw table.
Fig. 56
B
B
H
G
G
E
Fig. 57
21
Fig. 58
ASSEMBLING
UNIFENCE GUIDE RAIL
B
1. Locate the T-Slot Guide Rail and mounting hardware
Fig. 59, from the packing material of the Unifence.
Remove the end caps (A) Fig. 59, prior to assembly, by
inserting a flat headed screwdriver (B) into the channel
and tap gently as shown. NOTE: Take care not to damage either the cap or the rail.
A
A
Fig. 59
2. Insert two 3/8-24 x 1 hex head bolts, flat washers
and hex nuts (C) Fig. 60, into the two holes (F) Fig. 60 in
the front of saw table (G). Screw bolts into nuts slightly
leaving bolt head extended approximately 1/2 . Note:
Make sure to use only the two holes shown at (F).
E
D
F
3. Insert one 1/4-20 x 3/4 hex head bolt, flat washer and
hex nut (D) Fig. 60, into the front support of the extension
table (E) Fig. 60. Screw bolt into nut slightly leaving bolt
head extended approximately 1/4 .
C
G
4. From either end, slide the T-Slot guide rail (A) Fig.
61, onto the hex head of the bolts partially inserted in
step 2 and 3 above. Note: The bolt heads on the saw
table slide into the upper t-slot (B) Fig. 61 and the bolt
head on the extension table slide into the lower t-slot (C)
Fig. 61.
Fig. 60
B
A
5. Slide the guide rail along until the “0” on the unifence
scale is aligned with the right edge of the saw table.
snugg the hex nuts on the saw and extension table but
do not tighten at this time.
C
Fig. 61
6. Adjust the guide rail (C) Fig. 62, parallel with the saw
table surface by placing a square (H) on the saw table at
both the left front ends of the saw table (A) and the right
front end of the extension table (B), with the rule of the
square against the flat surface on top of the guide rail.
The guide rail (C) Fig. 62, can be adjusted up or down
slightly at either end. After you are certain the guide rail
is parallel with the table surface, firmly tighten the two
hex nuts that fasten the guide rail to the table. Note:
Make sure “0” (D) on the unifence scale is aligned with
the right edge of the saw table (E).
E
H
D
A
“0”
C
Fig. 62
22
B
7. Move the square (H) Fig. 62, to the end of the
Unifence table and check to make certain the same distance is kept from the top surface of the extension table
(K) to the top surface of the guide rail (C). Move the front
table support (L) Fig. 63, against the guide rail (C), and
fasten with 1/4-20 nut and flat washer (M). Tighten two
wood screws, one of which is shown at (N) Fig. 63, that
fasten the Unifence table to the guide rail.
N
ASSEMBLING
RAIL STOP
1. The Unifence Flip Stop Fig. 64 can be easily assembled by inserting flip stop (A) into fence slide stop (B)
which is held in place by inserting (C) 1/4-20 x 2 hex
head bolt (C), fiber washers (D) and tightening hex nut
(E). Make sure fiber washers are placed on both sides of
flip stop (A) when assembled. Do not over tighten hex
nut (E) as the flip stop must move freely.
M
L
C
Fig. 63
E
F
B
D
2. The Rail Stop Assembly Fig. 65 can then be attached
to the guide rail by inserting head of 5/16-18 (F) hex
head bolt into T-Slot (G) positioning the stop assembly to
the rail and tightening knob (H) finger tight.
3. Using a rubber mallet (P) Fig. 66, or a hammer and a
block of wood, gently tap end cap (R) into both ends of
the guide rail (C). NOTE: To avoid damage to the guide
rail, DO NOT use a metal hammer directly against the
guide rail.
A
H
C
Fig. 64
P
G
C
F
R
H
Fig. 65
Fig. 66
ADJUSTING T-SLOT
RAIL STOP
A
1. The Rail Stop Assembly Fig. 67 (A) can adjusted to
any number of positions along the guide rail providing a
quick stop setting for the Unifence body by loosening
knob (B) and sliding the stop along the rail to the desired
position (
) and re-tighten.
2. Any number of stops Catalog No. 36-899 can be
purchased and installed to provide time saving quick
stop adjustment for the Unifence body.
B
23
Fig. 67
E
B
A
C
F
C
B
A
D
Fig. 70
Fig. 68
A
B
B
Fig. 69
G
Fig. 71
ASSEMBLING CURSOR
TO UNIFENCE BODY
1. Remove two screws and flat washers (A) Fig. 68, and
assemble the cursor (B) to the Unifence body (C).
Replace the two screws and flat washers (A).
2. Fig. 69, illustrates the cursor (B) assembled to the
Unifence body. Final adjustment to the cursor (B) will be
made later.
B
ASSEMBLING UNIFENCE
BODY TO GUIDE RAIL
G
1. Turn fence body (A) Fig. 70, upside down and lay it on
a table or bench. Push handle (B) in against fence body.
Make certain the surface (C) of clamp bracket is parallel
to the face (D) of the fence body, and that the inside edge
(E) of the clamp bracket is parallel to surface (F) of the
fence body. Turn handle (B) Fig. 70, if necessary.
2. Place fence body (A) Fig. 71, onto the guide rail as
shown, making sure clamp bracket is inserted into channel (G) on rail. Notice that the clamp handle (B) is turned
to the left indent position.
3. Turn handle (B) Fig. 72, to the right indent position as
shown. This will prevent fence clamp from sliding out of
the channel (G).
4. Lock fence body (A) to the guide rail by pushing
down on handle (B) as shown in Fig. 73.
Fig. 72
B
24
Fig. 73
A
C
C
A
A
B
B
Fig. 74
Fig. 75
ASSEMBLING UNIFENCE
TO UNIFENCE BODY
C
1. The fence (A) can be assembled to clamp plate (B)
in either the horizontal position as shown in Fig. 74, or
the vertical position as shown in Fig. 75. Make certain
the two lock knobs (C), are loose and slide fence (A) onto
clamp plate (B) as shown. Then tighten the two lock
knobs (C).
2. For most cutting operations, the bottom of the fence
should be positioned slightly above the table surface.
Loosen two lock knobs (C) Fig. 76, and place a thin
object such as a ruler (D) between the table and fence,
as shown. Then tighten two lock knobs (C).
D
Fig. 76
BIESEMEYER T-SQUARE FENCE SYSTEM
ASSEMBLY INSTRUCTIONS
1. DISCONNECT THE SAW FROM THE POWER SOURCE.
2. Assemble the front rail (A) Fig. 77, to front of saw table using the two 3/8-16 x 1-1/4 long flat head Phillips screws
(B), 7/8 flat washers, lock washers and 3/8-16 hex nuts supplied. Screws (B) are inserted through the two holes in the
front rail, as shown and through the two through holes in the front of the saw table and fastened to the table with the
flat washers, lockwashers and hex nuts. IMPORTANT: Do not completely tighten front rail mounting hardware at
this time.
D
A
B
B
Fig. 78
Fig. 77
25
D
E
B
F
A
Fig. 80
Fig. 79
3. Using the template (D) Figures 78 and 79, check and adjust front rail at both ends of the saw table as shown, to
make sure rail (A) is level with table surface and tighten rail mounting hardware (B). IMPORTANT: Template (D) must
be on saw table when checking, not on extension wing.
4. Assemble rear rail (E) Fig. 80, to rear of saw table using the two 3/8-24 x 1-1/4 long hex head screws (F), 7/8 flat
washers and lockwashers as shown.
5 Make certain top edge of rail (E) Fig. 80 is below table surface and that top edge of cut-outs (G) are below miter
gage slots before tightening screws (F).
Fig. 81
6. If you did not purchase the accessory right extension table for use with your
T-Square® fence, construct an extension table by following the dimensions
shown in Fig. 81.
26
5- 3/8² (M)
H
2- 3/8² (L)
I
1- 3/4² (K)
J
P
P
Fig. 83
Fig. 82
7. Mark the position of the four leg mounting holes from
each end of the table as shown in Fig. 82. Using a 1/4
drill bit, drill four through holes through the end piece (J)
of the table at the dimensions shown at (K) (L) and (M).
L
8. Position the two legs (H) as shown in Fig. 83.
Assemble the four 1/4-20 x 1-1/2 long leg mounting
screws, washers and hex nuts (I) into holes drilled in step
7 and tighten. Mark the eight holes (P) to attach the legs
to the table top. Remove the screws and two legs (H).
Using a 1/16 drill bit, drill the eight holes 1/2 deep.
I
J
N
IMPORTANT NOTE: If your saw and fence system will
be used with a mobile base underneath the saw base
and table legs, the position of the legs may have to
be changed to fit onto the mobile base.
Fig. 84
9. Fasten the leg bracket (L) Fig. 84, to the underside of table top using the eight 3/4 long wood screws (N). Assemble
the four 1-1/2 long flat head Phillips screws, flat washers and hex nuts (I) to the end piece (J) of the table and retighten. Fasten the remaining leg to the extension table in the same manner.
10. Place table assembly (N) Fig. 85, in position between the two rails, as shown. Make sure end of table (O) is flush
against saw table (P) and using a bar clamp (Q) snug up end of rails to hold table in position. Using a straight edge
make sure table (O) is in the same plane and level with saw table (P). Lightly tap table up or down and adjust leveling
screws (R) Fig. 86, in bottom of legs to accomplish this. When you are certain table (O) Fig. 85, is level and in the same
plane with saw table (P), tighten bar clamp (Q) to hold everything in position. Then drill 1/4 through holes through the
front and rear of the extension table using the holes (S) provided in rails as template.
P
O
N
R
Q
S
Fig. 86
Fig. 85
27
V
U
T
X
Fig. 87
11. After the holes have been drilled in the edge of the front and rear extension
table board, fasten both front and rear rail to table using the 1-1/2 flat head
Phillips screws (T) Fig. 87, 1-1/4 O.D. flat washers (U) and hex nuts (V). NOTE:
The 1-1/4 flat washer cannot be used on the end holes (X).
12. Lay the guide tube (B) Fig. 88, on the saw table as
shown, and line up the threaded holes (C) on bottom of
guide tube (B) with the through holes (D) on the front rail
(A) in seven places.
B
C
A
D
Fig. 88
13. Position the guide tube (B) Figs. 89 on the front rail
and fasten the guide tube to the rail using the 1/2 long
hex screws (G) and lockwashers in seven places.
B
G
Fig. 89
28
CONNECTING SAW TO POWER SOURCE
POWER CONNECTIONS
A separate electrical circuit should be used for your tools. This circuit should not be less than #12
wire and should be protected with a 20 Amp fuse. Have a certified electrician replace or repair a
worn cord immediately. Before connecting the motor to a power line, make sure the switch is in
the “OFF” position and be sure that the electric current is of the same characteristics as stamped
on the motor nameplate. Running on low voltage will damage the motor.
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug
and a 3-hole receptacle which will accept the tool’s
plug. When using an extension cord, be sure to use
one heavy enough to carry the current of the saw. An
undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. Fig. 90
shows the correct size to use depending on cord
length. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
TOTAL LENGTH OF
CORD IN FEET
120 VOLT
25
50
GAGE OF EXTENSION
CORD TO USE
240 VOLT
50
100
14 AWG
12 AWG
NOTE: EXTENSION CORDS LONGER THAN 100 FEET
ARE NOT RECOMMENDED.
Fig. 90
GROUNDING INSTRUCTIONS
CAUTION: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR
FROM ELECTRIC SHOCK.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. The motor is equipped with an electric cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with
insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is necessary, do not connect the equipment grounding conductor to
a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or
if in doubt as to whether the tool is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding type plugs and 3-hole receptacles that accept the tool’s
plug as shown in Fig. 91.
Repair or replace damaged or worn cord immediately.
29
115 VOLT, SINGLE PHASE OPERATION
1. This tool must be grounded while in use to protect the
operator from electric shock. The motor recommended
for use with your saw is shipped wired for 115 volts and
is intended for use on a circuit that has an outlet which
looks like the one illustrated in Fig. 91. The tool is supplied with a three-prong grounding type plug which is
also illustrated in Fig. 91.
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
2. If a properly grounded outlet is not available, a temporary adapter, shown in Fig. 92, may be used for connecting the 3-prong grounding type plug to a 2prong
receptacle. The temporary adapter should be used only
until a properly grounded outlet can be installed by a
qualified electrician. The green colored rigid ear, lug, or
the like extending from the adapter must be connected
to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be
held in place with a metal screw.
GROUNDING BLADE
IS LONGEST OF THE THREE BLADES
Fig. 91
GROUNDED OUTLET BOX
NOTE: In Canada, the use of a temporary
adapter is not permitted by the Canadian
Electric Code.
GROUNDING MEANS
ADAPTER
Fig. 92
230 VOLT, SINGLE PHASE OPERATION
The motor supplied with your saw is a dual voltage,
115/230 volt motor. If it is desired to operate your saw at
230 volts, single phase, it is necessary to reconnect the
motor leads in the motor junction box by following the
instructions given on the motor nameplate. WARNING:
MAKE SURE MOTOR IS DISCONNECTED FROM
POWER SOURCE BEFORE RECONNECTING MOTOR
LEADS. It is also necessary to replace the 115 volt plug,
supplied with the motor, with a UL/CSA Listed plug suitable for 230 volts and the rated current of the saw as
illustrated in Fig. 93. Contact your local Authorized Delta
Service Center or qualified electrician for proper procedures to install the plug. The saw must comply with all
local and national electrical codes after the 230 volt plug
is installed.
CURRENT CARRYING PRONGS
230
VOLT
GROUND PRONG
Fig. 93
The saw with a 230 volt plug should only be connected to an outlet having the same configuration as the plug illustrated in Fig. 93. No adapter is available or should, be used with the 230 volt plug. CAUTION: IN ALL CASES MAKE
CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A CERTIFIED ELECTRICIAN CHECK THE RECEPTACLE.
30
FASTENING STAND TO SUPPORTING SURFACE
IF DURING OPERATION THERE IS ANY TENDENCY FOR THE SAW TO TIP OVER, SLIDE OR WALK ON
THE SUPPORTING SURFACE, THE SAW STAND CAN BE SECURED TO THE FLOOR SURFACE. THE
RUBBER FEET OF THE STAND FEATURE HOLES WHICH ALLOW EASY MOUNTING WITHOUT REMOVING THE SAW FROM THE STAND.
OPERATING CONTROLS AND ADJUSTMENTS
STARTING AND STOPPING SAW
1. The on/off switch is located underneath the switch shield (A) Fig. 94. To turn the saw “ON,” move
switch trigger (B) to the up position.
2. To turn the saw “OFF,” simply push down on switch shield (A) Fig. 95.
A
A
B
Fig. 94
Fig. 95
LOCKING SWITCH IN
THE “OFF” POSITION
IMPORTANT: When the unit is not in use, the switch
(B) should be locked in the “OFF” position using a
padlock (C) Fig. 96, (with 3/16² diameter shackle)
through the two holes in the switch plate, as shown
in Fig. 96. NOTE: Padlock shown is available as
accessory Catalog No. 50-325.
C
B
Fig. 96
OVERLOAD PROTECTION
The motor recommended for use with your saw is
equipped with a reset overload relay button (A) Fig. 97. If
the motor shuts off or fails to start due to overloading
(cutting stock too fast, using a dull blade, using the saw
beyond its capacity, etc.), or low voltage, turn the switch
to the “OFF” position, let the motor cool three to five
minutes and push the reset button (A), which will reset
the overload device.The motor can then be turned on
again in the usual manner.
A
Fig. 97
31
RAISING AND LOWERING
THE BLADE
To raise the saw blade, loosen lock knob (A) Fig. 98, and
turn the blade raising handwheel (B) clockwise. When
the blade is at the desired height, tighten lock knob (A).
To lower the blade, loosen lock knob (A) Fig. 98, and turn
the handwheel (B) counterclockwise. NOTE: One full
turn of the handwheel will change blade height approximately 1/4 .
B
D
A
C
E
TILTING THE BLADE
Fig. 98
To tilt the saw blade for bevel cutting, loosen lock knob
(C) Fig. 98, and turn the tilting handwheel (D). When the
desired blade angle shown on scale and pointer (E) is
obtained, tighten lock knob (C).
ADJUSTING 90 DEGREE AND
45 DEGREE POSITIVE STOPS
Your saw is equipped with positive stops that will quickly and accurately position the saw blade at 90 degrees
and 45 degrees to the table. To check and adjust the
positive stops, proceed as follows:
1. WARNING: When adjusting the positive stops,
make certain the machine is disconnected from the
power source.
2. Raise the saw blade to its highest position.
3. Set the blade at 90 degrees to the table by turning
the blade tilting handwheel counterclockwise as far as it
will go.
4. Using a combination square (A) Fig. 99, check to see
if the blade is at 90 degrees to the table surface as
shown.
5. If the blade is not at 90 degrees to the table, loosen
set screw (B) Fig. 99 with supplied wrench (C), and turn
the blade tilting handwheel until you are certain the blade
is at 90 degrees to the table. Turn set screw (B) clockwise until it bottoms.
6. Adjust the pointer (D) Fig. 100, to point to the zero
degree mark on the scale by loosening screw (E), adjusting pointer (D), and tightening screw (E).
7. Turn the blade tilting handwheel clockwise as far as
it will go and using a combination square, check to see if
the blade is at 45 degrees to the table.
8. If the blade is not at 45 degrees to the table, loosen
set screw (F) Fig. 99, and turn blade tilting handwheel
until you are certain the blade is 45 degrees to the table.
Turn set screw (F) clockwise until it bottoms.
C
A
B
F
Fig. 99
E
D
Fig. 100
32
BACKLASH ADJUSTMENTS FOR BLADE RAISING
AND BLADE TILTING MECHANISMS
After a period of extended use, if any play is detected in
the blade raising or blade tilting mechanisms, the following adjustments should be made.
C
1. Make certain the machine is disconnected from
the power source.
D
2. NOTE: The machine has been turned upside down
and the blade removed for clarity and safety.
3. Adjusting blade raising mechanism - Loosen locknut (A) Fig. 101, and turn eccentric sleeve (B) until all play
is removed in mechanism and tighten locknut (A).
A
B
4. Adjusting blade tilting mechanism - Loosen locknut (C) Fig. 101, and turn eccentric (D) until all play is
removed in mechanism and tighten locknut (C).
Fig. 101
CHECKING BLADE ALIGNMENT
1. Disconnect the saw from power source.
H
2. Raise blade guard and adjust blade to its highest
position. Mark one side of one saw blade tooth (F) with a
dark colored marker Fig. 101A. Rotate the blade toward
the front of the saw by hand until the marked tooth is at
the top of the table.
F
3. Insert the miter gage into miter gage slot and position near the front edge of the blade. With a combination
square (G), place the straight edge along the face of the
miter gage. Position the end of the straight edge (H) to
lightly contact the side of the marked tooth.
4. Firmly hold the straight edge in place while rotating
blade marked tooth to the rear side of the table. Firmly
holding the straight edge in place, re-position the miter
gage to the rear side of the saw table Fig. 101B . Rotate
the blade with marked tooth (F) to end of straight edge to
check blade alignment gap. The marked tooth (F) should
be about the same distance from the end of the straight
edge in front and rear positions.
G
Fig. 101A
5. Repeat this procedure moving from front to rear until
you have visual confirmation of the blade alignment.
NOTE: All saw blades have some run-out, therefore, you
may need to check the alignment each time a blade is
changed.
F
6. If the blade alignment is off by .010 or the approximate thickness of a standard business card, follow
(ADJUSTING BLADE ALIGNMENT) procedure.
7. Lower blade guard and saw blade before reconnecting power source.
Fig. 101B
33
ADJUSTING BLADE ALIGNMENT
WARNING: Blade Alignment is Factory Set and should
not need adjustment. Adjusting Blade Alignment, in the
field, is a difficult and time-consuming procedure. All
Saw Blades have some run-out, therefore re-adjusting
blade alignment should only be attempted if it becomes
necessary. (See step 6 in CHECKING BLADE ALIGNMENT.)
1. Disconnect the saw from power source.
2. Lower blade; remove blade guard and table insert.
With a 1/2 wrench, loosen the 4 front and rear trunnion
E
mounting bolts (E) Fig. 101C. NOTE: Only the 2 rear trunnion mounting bolts are shown.
3. Move the trunnion assembly in the desired direction.
Tap gently with rubber mallet if necessary.
Fig. 101C
4. To check blade alignment, follow (CHECKING BLADE
ALIGNMENT) procedure until proper alignment is achieved.
Tighten 4 trunnion bolts (E).
5. Check blade alignment again after tightening bolts to confirm alignment. If alignment is off, loosen the 4 trunnion
bolts (E) and repeat the above steps until proper alignment is achieved with bolts fully tightened.
6. Install table insert, blade guard and lower blade before reconnecting power source.
MITER GAGE OPERATION AND ADJUSTMENT
1. Insert the miter gage bar into the miter gage slot and
assemble the washer and lock handle (A) Fig. 102, to the
miter gage bar as shown. Insert cap (K) into top of handle (A).
2. The miter gage is equipped with adjustable index stops
at 90 degrees and 45 degrees right and left. Adjustment to
the index stops can be made by tightening or loosening the
three adjusting screws (B) Fig. 103.
3. To rotate the miter gage, loosen lock knob (A) Fig. 103,
and move the body of the miter gage (C) to the desired
angle.
4. The miter gage body will stop at 90 degrees and 45
degrees both right and left. To rotate the miter gage body
past these points, the stop link (D) Fig. 103, must be
moved up and out of the way.
5. The head of the miter gage pivots on a special tapered
screw (G) that fastens the head to the miter gage bar. If the
miter gage head does not pivot freely, or pivots too freely,
it can be adjusted by loosening set screw (H) Fig. 104, and
turning the screw (G), in or out. Be certain to tighten screw
(H) after adjustment is made.
K
A
Fig. 102
H
C
A
E
F
B
B
G
D
Fig. 103
Fig. 104
34
ADJUSTING TABLE INSERT
B
MAKE CERTAIN THE MACHINE IS DISCONNECTED
FROM THE POWER SOURCE.
Place a straight edge across the table at both ends of the
table insert as shown in Fig. 105. The table insert (A)
should always be level with the table. If an adjustment is
necessary, turn the adjusting screws (B), as needed.
Four adjusting screws (B) are supplied in the table insert.
The table insert is equipped with a convenient finger hole
(C) for easy removal.
A
C
B
Fig. 105
CHANGING THE SAW BLADE
1. MAKE CERTAIN THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE.
2. NOTE: Two 7/8 wrenches are supplied with the saw for changing the saw blade: a box end
wrench (A) Fig. 107, and open end wrench (B). Use only 10 saw blades with 5/8 arbor holes
and rated for 3000 RPM or higher.
3. Remove table insert (C) Fig. 106, and raise saw blade to its maximum height.
4. Place the open end wrench (B) Fig. 106, on the flats of the saw arbor to keep the arbor from
turning, and using wrench (A), turn the arbor nut toward the front of the saw. Remove arbor nut,
blade flange, and saw blade.
5. Assemble the new blade, making certain the teeth point down at the front of the saw table,
and assemble outside blade flange and arbor nut. With wrench (B) Fig. 106, on the flats of the
arbor to keep it from turning, tighten arbor nut by turning wrench (A) counterclockwise.
6. Replace table insert.
B
C
B
A
A
Fig. 107
Fig. 106
35
STORING THE MITER GAGE,
RIP FENCE, AND ARBOR
WRENCHES
1. When not in use, the miter gage (A) Fig. 108, can be
stored through the hole located at the front side of the
stand as shown.
B
2. The rip fence (B) Fig. 108, can be conveniently
stored out-of-the-way on the stamped ledges on the
right side of the saw stand.
A
3. Arbor wrenches (C) Fig. 109, can be stored on one
of the two notched legs.
Fig. 108
DUST CHUTE
The saw stand support panel (D) Fig. 109, also serves as
a natural built-in dust chute. This dust chute (D) allows
the sawdust to conveniently escape out the rear of the
saw stand and away from the work area.
D
UNIFENCE OPERATION
C
Fig. 109
1. Before operating fence, make sure the fence is
adjusted parallel to miter gage slot, as explained later on
in this manual.
2. For most normal ripping operations of standard size
lumber, the fence is used in the vertical position, as
shown in (A) Fig. 110.
A
Fig. 110
3. When ripping thin stock, it is sometimes more convenient to use the fence in the horizontal position, as
shown in (B) Fig. 111.
B
36
Fig. 111
4. To move the fence along the guide rail, simply lift up
clamp lever (A), as shown in Fig. 112, slide fence to
desired position on the rail, and push down on clamp
lever (A) to lock fence in place.
A
Fig. 112
5. The distance the fence is positioned away from the
blade is indicated by the two witness lines (B) and (C) Fig.
113, located on the cursor (D). The witness lines (B) and
(C) easily indicate the distance the fence is positioned
away from the saw blade. Witness line (B) indicates the
distance the fence is away from the blade when the fence
is in the horizontal position Fig. 111, and witness line (C)
indicates the distance the fence is away from the blade
when the fence is in the vertical position Fig. 110. If it is
necessary to adjust cursor (D), make a test cut with the
fence in either the vertical or horizontal position, measure
the distance of the finished cut and move the cursor (D)
by loosening the two screws (E) Fig. 113. After adjustment is completed tighten the two screws (E).
B
E
C
D
E
Fig. 113
6. To remove the fence and fence body assembly (F)
Fig. 114, from the guide rail, lift up on fence clamping
lever (A) and turn lever (A) to the left indent position. The
fence assembly (F) can then be pulled straight off the
guide rail and removed, as shown in Fig. 114.
ADJUSTING FENCE
PARALLEL TO
MITER GAGE SLOTS
A
Fig. 114
The fence (A) Fig. 115, should be adjusted so it is parallel to miter gage slots (B). To check and adjust, move the
fence (A) until the bottom front edge of the fence is in line
with the edge of the miter gage slot as shown, and push
down on fence clamping lever (C). Check to see if the
fence is parallel to the miter gage slot the entire length of
the table. If the rear of the fence must be moved, slightly
tighten or loosen one of the adjustment plugs (D) or (E)
Fig. 115, using the arbor wrench or 7/8 wrench, until the
fence is parallel with the miter gage slot. IMPORTANT:
DO NOT OVERTIGHTEN ADJUSTMENT PLUGS (D)
AND (E) FIG. 115. VERY LITTLE MOVEMENT OF THESE
ADJUSTMENT PLUGS IS NECESSARY WHEN
ADJUSTING THE FENCE PARALLEL WITH THE
MITER GAGE SLOT.
A
E
B
D
C
37
Fig. 115
ADJUSTING FENCE
90 DEGREES TO TABLE
B
A
The fence must be adjusted so that the face of fence (A)
Fig. 116, is 90 degrees to the table. To check if the fence
is 90 degrees to the table, place a square (B) on the table
with one end of the square against the fence, as shown.
If an adjustment is necessary, tighten or loosen one of
two screws (C) or (D) using the wrench supplied, until the
fence is 90 degrees to the table. IMPORTANT: VERY
LITTLE MOVEMENT OF THESE SCREWS (C) AND (D)
IS NECESSARY TO MAKE THIS ADJUSTMENT.
D
C
Fig. 116
ADJUSTING CLAMPING
ACTION OF FENCE
LOCKING HANDLE
When the fence locking handle (A) is pushed to the
down position, as shown in Fig. 117, the fence body (B)
should be completely clamped to the guide rail. If the
fence body (B) is not completey clamped to the guide
rail when the handle (A) is in the position shown in Fig.
117, lift up on locking handle (A) Fig. 118, and slightly
tighten two adjustment plugs (C) using arbor wrench or
7/8 wrench. Adjustment plugs (C) should be tightened
an equal amount. Check to see if the fence body (B) is
completely fastened to the rail by pushing down on locking lever (A). Adjust further if necessary.
A
B
Fig. 117
IMPORTANT: AFTER ADJUSTING THE CLAMPING
ACTION OF THE FENCE LOCKING HANDLE, CHECK
TO SEE IF THE FENCE IS PARALLEL TO THE MITER
GAGE SLOT AND ADJUST IF NECESSARY.
C
B
C
Fig. 118
REPOSITIONING MOTOR
FOR STORAGE
When the saw is not in use, the motor can be repositioned so it hangs straight down at the rear, enabling you
to move the saw against a wall. This can be accomplished by removing the belt and repositioning the motor
and motor mounting plate, as shown in Fig. 119.
38
Fig. 119
A
OPERATIONS
Common sawing operations include ripping and cross-cutting plus a few other standard operations of a fundamental
nature. As with all power tools, there is a certain amount of hazard involved with the operation and use of the tool. Using
the tool with the respect and caution demanded as far as safety precautions are concerned, will considerably lessen
the possibility of personal injury. However, if normal safety precautions are overlooked or completely ignored, personal injury to the operator can result. The following information describes the safe and proper method for performing the
most common sawing operations.
NOTE: THE USE OF ATTACHMENTS AND ACCESSORIES NOT RECOMMENDED BY DELTA MAY RESULT IN
THE RISK OF INJURY TO PERSONS.
CROSS-CUTTING
Cross-cutting requires the use of the miter gage to position and guide the work. Place the work against the miter gage
and advance both the gage and work toward the saw blade, as shown in Fig. 120. The miter gage may be used in either
table slot. When bevel cutting (blade tilted), use the left miter gage slot so that the blade tilts away from the miter gage
and your hands.
Start the cut slowly and hold the work firmly against the miter gage and the table. One of the rules in running a saw is
that you never hang onto or touch a free piece of work. Hold the supported piece, not the free piece that is cut off. The
feed in cross-cutting continues until the work is cut in two, and the miter gage and work are pulled back to the starting point. Before pulling the work back, it is good practice to give the work a little sideways shift to move the work
slightly away from the saw blade. Never pick up any short length of free work from the table while the saw is running.
A smart operator never touches a cut-off piece unless it is at least a foot long.
Fig. 120
For added safety and convenience the miter gage can
be fitted with an auxiliary wood-facing (C), as shown in
Fig. 121, that should be at least 1 inch higher than the
maximum depth of cut, and should extend out 12 inches or more to one side or the other depending on which
miter gage slot is being used. This auxiliary wood-facing
(C) can be fastened to the front of the miter gage by
using two wood screws (A) through the holes provided in
the miter gage body and into the wood-facing.
A
A
C
Fig. 121
39
USING THE FENCE AS A CUT-OFF GAGE
The fence can be used as a cut-off gage when cross
cutting a number of pieces to the same length. IMPORTANT: WHEN USING THE FENCE AS A CUT-OFF
GAGE, IT IS VERY IMPORTANT THAT THE REAR END
OF THE FENCE BE POSITIONED IN FRONT OF THE
SAW BLADE.
When using the fence as a cut-off gage, simply position
the fence (A) to the front as shown in Fig. 122, or purchase the accessory 34-878, 12 long fence (B), as
shown in Fig. 123. Fig. 124, illustrates a typical operation
using the accessory 34-878 12 long fence (B) as a cutoff gage.
A
Fig. 122
B
B
Fig. 123
Fig. 124
RIPPING WITH THE UNIFENCE
Ripping is the operation of making a lengthwise cut through a board, as shown in Fig. 125, and
the rip fence (A) is used to position and guide the work. One edge of the work rides against the
rip fence while the flat side of the board rests on the table. Since the work is pushed along the
fence, it must have a straight edge and make solid contact with the table. The saw blade guard
must be used. On Delta saws, the guard has anti-kickback fingers to prevent kickback and a
splitter to prevent the wood kerf from closing and binding the blade.
Never stand in the line of the saw cut when ripping. Hold
the work with both hands and push it along the fence
and into the saw blade as shown in Fig. 125. The work
can then be fed through the saw blade with one or two
hands. After the work is beyond the saw blade and antikickback fingers, the hand is removed from the work.
When this is done the work will either stay on the table,
tilt up slightly and be caught by the end of the rear guard
or slide off the table to the floor. Alternately, the feed can
continue to the end of the table, after which the work is
lifted and brought along the outside edge of the fence.
The cut-off stock remains on the table and is not
touched with the hands until the saw blade is stopped,
unless it is a large piece allowing safe removal. When
ripping boards longer than three feet, it is recommended that a work support be used at the rear of the saw to
keep the workpiece from falling off the saw table.
A
Fig. 125
40
B
A
Fig. 126
Fig. 127
If the ripped work is less than 4 inches wide, a push stick
should always be used to complete the feed, as shown
in Fig. 126. The push stick can easily be made from
scrap material as explained in the section “CONSTRUCTING PUSH STICK.” When ripping stock 2 inches or narrower, assemble an auxiliary wood facing to the
fence, as explained in the section “USING AUXILIARY
WOOD FACING ON THE UNIFENCE” and use a push
stick.
B
When ripping material with a veneer facing that extends
over the material, the fence (A) should be in the horizontal position with the veneer (B) extending over the lip of
the fence, as shown in Fig. 127.
Fig. 128
C
When ripping material with a veneer facing and the
material is not thick enough for the veneer to extend
over the lip of the fence or if the veneer facing (B) is on
both sides of the material, as shown in Fig. 128, the
fence can be positioned slightly above the surface of the
table. The veneer can be placed between the fence and
the table or the veneer can straddle the fence with the
material solidly against the fence, as shown.
B
A
Fig. 129
RIPPING ON LEFT
SIDE OF SAW BLADE
C
In some cases it may be desirable to use the fence on
the left side of the saw blade. This is easily accomplished by repositioning the fence (A) Figs. 129 and 130,
fence clamp bar (B), and lock knobs (C) so that the fence
(A) will be attached to the right side of the fence body, as
shown in Fig. 130. The complete fence assembly (D)
Fig. 130, can easily be moved to the left side of the saw
table.
A
D
41
Fig. 130
USING ACCESSORY
MOULDING CUTTERHEAD
Moulding is cutting a shape on the edge or face of the
work. Cutting mouldings with a moulding cutterhead in
the circular saw is a fast, safe and clean operation.The
many different knife shapes available make it possible for
the operator to produce almost any kind of mouldings,
such as various styles of corner moulds, picture frames,
table edges, etc.
The moulding head consists of a cutterhead in which can
be mounted various shapes of steel knives, as shown in
Fig. 131. Each of the three knives in a set is fitted into a
groove in the cutterhead and securely clamped with a
screw. The knife grooves should be kept free of sawdust
which would prevent the cutter from seating properly.
Fig. 131
H
IMPORTANT: For certain cutting operations such as
dadoing and moulding where you are not cutting
completely through the workpiece, the blade guard
and splitter assembly cannot be used. Simply loosen
screws (G) and (H) Fig. 132. Lift up and swing blade
guard and splitter assembly (W) Fig. 133, to the rear
of the saw as shown. CAUTION: Always return and
fasten the blade guard and splitter assembly to its
proper operating position for normal thru-sawing
operations as shown in Fig. 32 and 33 on page 15.
G
Fig. 132
W
Fig. 133
The moulding cutterhead (A) Fig. 134, is assembled to
the saw arbor as shown. Also, the accessory moulding
cutterhead table insert (B), must be used in place of the
standard table insert.
Fig. 134
42
It is necessary when using the moulding cutterhead to
add wood-facing (C) to the face of the rip fence, as
shown in Fig. 135. The wood-facing is attached to the
fence with wood screws through holes which must be
drilled in the fence. 3/4 inch stock is suitable for most
work although an occasional job may require 1 inch facing.
C
Position the wood-facing over the cutterhead with the
cutterhead below the surface of the table. Turn the saw
on and raise the cutterhead. The cutterhead will cut its
own groove in the wood-facing. Fig. 135, shows a typical moulding operation. See accessories page 48 for
molding cutterhead set. NEVER USE MOULDING CUTTERHEAD IN A BEVEL POSITION.
Fig. 135
IMPORTANT: NEVER RUN THE STOCK BETWEEN THE
FENCE AND THE MOULDING CUTTERHEAD AS
IRREGULAR SHAPED WOOD WILL CAUSE KICKBACK.
IMPORTANT: Special attention should be given the grain direction. Make all cuts in the same
direction as the grain whenever possible.
ALWAYS INSTALL BLADE GUARD AFTER OPERATION IS COMPETE.
USING ACCESSORY DADO HEAD
IMPORTANT: THE BLADE GUARD AND SPLITTER ASSEMBLY CANNOT BE USED WHEN DADOING OR MOULDING AND MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW AS
DESCRIBED ON PAGE 15, FIG. 32 AND 33 OF THIS MANUAL.
Dadoing is cutting a rabbet or wide groove into the work.
Most dado head sets are made up of two outside saws
and four or five inside cutters, as shown in Fig. 136.
Various combinations of saws and cutters are used to
cut grooves from 1/8 to 13/16 for use in shelving, making joints, tenoning, grooving, etc. The cutters are heavily swaged and must be arranged so that this heavy portion falls in the gullets of the outside saws, as shown in
Fig. 137. The saw and cutter overlap is shown in Fig. 138,
(A) being the outside saw, (B) an inside cutter, and (C) a
paper washer or washers which can be used as needed
to control the exact width of groove. A 1/4 groove is cut
by using the two outside saws. The teeth of the saws
should be positioned so that the raker on one saw is
beside the cutting teeth on the other saw.
Fig. 136
B
A
C
Fig. 137
43
Fig. 138
The dado head set (D) Fig. 139, is assembled to the saw
arbor as shown. IMPORTANT: The blade guard and
splitter assembly cannot be used when dadoing and
must be removed or swung to the rear of the saw as
explained previously in this manual. Auxiliary jigs,
fixtures, push sticks and feather boards should also be
used. Also, the accessory dado head table insert (E)
Fig. 139, must be used in place of the standard table
insert. See accessories page 48 for dado head set.
Fig. 139
Fig. 140, shows a typical dado operation using the miter
gage as a guide.
WARNING: NEVER USE THE DADO HEAD IN A BEVEL
POSITION.
IMPORTANT: ALWAYS INSTALL BLADE GUARD AFTER
OPERATION IS COMPLETED.
Fig. 140
USING AUXILIARY WOOD FACING ON RIP FENCE
It is necessary when performing special operations such
as when using the moulding cutterhead to add wood
facing (A) Fig. 141, to one side of the rip fence as shown.
The wood facing is attached to the fence with wood
screws through holes drilled in the fence. 3/4-inch stock
is suitable for most work, although an occasional job
may require one-inch facing.
A
Fig. 141
44
BIESEMEYER T-SQUARE FENCE SYSTEM
FENCE OPERATION
IMPORTANT: Before operating fence, make sure the fence is adjusted parallel to
the miter gage slot, as explained later on in this manual.
A
E
A
Fig. 142
Fig. 143
1. To move the fence along the guide rail, simply lift up
clamp lever (A) as shown in Fig. 142, slide fence to
desired position on rail, and push down on clamp lever
(A) as shown in Fig. 143, to lock fence in position. NOTE:
A magnet (E) Fig. 143, is provided to hold clamp handle
(A) Figs. 142 and 143, in the up position when moving
the fence.
D
2. The distance the fence is positioned away from the
blade is indicated by the witness line (B) Fig. 144, located on the cursor (C). If it is necessary to adjust the cursor (C), make a test cut with the fence locked in position.
Measure the width of the finished cut and adjust the
cursor (C) by loosening the two screws (D), adjusting the
cursor (C) until the witness line (B) is aligned with the
same marking on the scale as the finished cut. Then
tighten the two screws (D).
C
B
Fig. 144
ADJUSTING FENCE PARALLEL TO MITER GAGE SLOTS
The fence (A) Fig. 145, must be adjusted so it is parallel
to the miter gage slots (B). To check and adjust, move
fence (A) until the bottom edge of the fence is in line with
the edge of one of the miter gage slots as shown, and
push down on the fence clamping lever (C). Check to
see if the fence (A) is parallel to the miter gage slot the
entire length of the table. If an adjustment must be
made, lift up fence locking lever (C) and raise fence up
off the guide tube, as shown in Fig. 146. Slightly tighten
or loosen one of the two adjusting screws (D) or (E) Fig.
146, using a 3/16 allen wrench (F), not supplied.
Replace the fence on the guide tube and check again to
see if the edge of the fence is parallel with the miter gage
slot the entire length of the slot. Repeat this adjustment
until you are sure the fence is parallel with the miter gage
slot.
IMPORTANT: VERY LITTLE MOVEMENT OF
SCREWS (D) AND (E) IS NECESSARY TO ADJUST
THE FENCE PARALLEL WITH THE MITER GAGE
SLOT.
A
B
C
Fig. 145
45
E
D
F
Fig. 146
ADJUSTING CLAMPING ACTION OF FENCE
LOCKING HANDLE
When the fence locking handle (A) is pushed to the down position, as shown in Fig. 147, the fence assembly (B) should
be completely clamped to the guide tube (C). If the fence assembly (B) is not completely clamped to the guide tube (C)
when the handle (A) is pushed down, as shown in Fig. 147, lift up handle (A) and raise fence assembly (B) up off the
guide tube (C). Slightly tighten the two adjusting screws (D) and (E) Fig. 148, using the 3/16 allen wrench (F) not supplied. Adjusting screws (D) and (E) Fig. 148, should be tightened an equal amount. Replace fence onto the guide
tube and re-check to see if the fence assembly (B) Fig. 147, is completely tightened to the guide tube (C) with the locking handle (A) pushed down. Adjust further if necessary. IMPORTANT: AFTER ADJUSTING THE CLAMPING ACTION
OF THE FENCE LOCKING HANDLE, CHECK TO SEE IF THE FENCE IS PARALLEL TO THE MITER GAGE SLOT
AND ADJUST IF NECESSARY.
E
D
B
A
F
C
Fig. 147
Fig. 148
LUBRICATION
1. Apply paste wax to fence and guide tube sliding surfaces weekly. Also, saw table and extension table surface
should be waxed often.
2. Apply grease to cam lock (A) Fig. 149, and cam foot
(B) occasionally to prevent wear.
46
Fig. 149
CONSTRUCTING A PUSH STICK
47
Fig. 150
1/2 SQUARES
CUT OFF HERE TO
PUSH 1/2 WOOD
CUT OFF HERE TO
PUSH 1/4 WOOD
NOTCH TO HELP
PREVENT HAND
FROM SLIPPING
MAKE FROM 1/2 OR 3/4
WOOD OR THICKNESS
LESS THAN WIDTH OF
MAT’L. TO BE CUT
PUSH STICK
When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be
made from scrap material by following the pattern shown in Fig.150.
ACCESSORIES
The testing of this unit has been accomplished with the following accessories.
For safest operation, it is recommended
that only these accessories be used with
this unit.
WARNING: Since accessories other
than those listed have not been tested
with this unit, use of such accessories
could be hazardous.
36-899
50-325
34-813
34-334
34-878
35-032
Unifence Flip Stop
Padlock
Moulding Cutterhead
with Knife Set
Dado Head Set
Cut-off Fence
10² Carbide Blade
48
49
50
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced
by a network of Porter-Cable/Delta Factory Service Centers and Delta Authorized Service
Stations. To obtain additional information regarding your Delta quality product or to obtain parts,
service, warranty assistance, or the location of the nearest service outlet, please call 1-888-8485175.
51
Delta Building Trades and Home Shop Machinery
Two Year Limited Warranty
Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or
machine accessory which in normal use has proven to be defective in workmanship or material,
provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta
with reasonable opportunity to verify the alleged defect by inspection. Delta may require that electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and
repair or replacement. Delta will not be responsible for any asserted defect which has resulted
from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone
other than an authorized Delta Service facility or representative. Under no circumstances will
Delta be liable for incidental or consequential damages resulting from defective products. This
warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect to
defective products; all other warranties, express or implied, whether of merchantability, fitness for
purpose, or otherwise, are expressly disclaimed by Delta.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable•Delta Power Tools are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable•Delta)
ARIZONA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
CALIFORNIA
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
COLORADO
Denver 80216
5855 Stapleton Drive North
Suite A-140
Phone: (303) 370-6909
Fax: (303) 370-6969
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
ILLINOIS
Addison 60101 (Chicago)
311 Laura Drive
Phone: (630) 628-6100
Fax: (630) 628-0023
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
MICHIGAN
Troy 48083 (Detroit)
1355 Combermere
Phone: (248) 597-5000
Fax: (248) 597-5004
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
MINNESOTA
Minneapolis 55429
4315 68th Avenue North
Phone: (612) 561-9080
Fax: (612) 561-0653
MISSOURI
North Kansas City 64116
1141 Swift Avenue
P.O. Box 12393
Phone: (816) 221-2070
Fax: (816) 221-2897
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
St. Louis 63119
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
NORTH CAROLINA
Charlotte 28209
4303-B South Boulevard
Phone: (704) 525-4410
Fax: (704) 525-0618
OHIO
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
TENNESSEE
Nashville 37214
2262 Lebanon Pike
Phone: (615) 882-0320
Fax: (615) 882-0051
TEXAS
Dallas 75220
10720 N. Stemmons Freeway
Phone: (214) 353-2996
Fax: (214) 350-3943
Houston 77055
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
WASHINGTON
Renton 98055 (Seattle)
268 Southwest 43rd Street
Phone: (425) 251-6680
Fax: (425) 251-9337
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 901-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable •Delta products should be obtained by contacting any Porter-Cable•Delta Distributor, Authorized
Service Center, or Porter-Cable•Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will
be directed to the nearest Porter-Cable•Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-487-8665 ó al 901-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable•Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable•Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable•Delta. Si no tiene acceso a ninguna de estas opciones, llame al
888-848-5175 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable•Delta más cercano.
PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
MANITOBA
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 836-2840
Fax: (519) 767-4131
QUÉBEC
1515 ave.
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
1447, Begin
St-Laurent, (Montréal),
Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE•DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE S.A.):
BAMMER®, INNOVATION THAT WORKS®, JETSTREAM®, LASERLOC®, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®,
PORTER-CABLE®, QUICKSAND®, SANDTRAP®, SAW BOSS®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR-EASE®, THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, WHISPER SERIES®, DURATRONIC™,
FLEX™, FRAME SAW™, MICRO-SET™, MORTEN™, NETWORK™, RIPTIDE™, TRU-MATCH™, WOODWORKER’S CHOICE™.
Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también
pueden estar registradas en otros países.
Printed in U.S.A.