Craftsman 315.111610 Owner`s manual

Owner's Manual
II:RRFTSMRNI
3/8 in. Two Speed / Reversible
CORDLESS DRILL
Model No.
315.111610
Save this manual for
future reference
_IL CAUTION;
Read and follow all
Safety Rules and Operating Instructions before first use of this
product.
Customer
• Operation
• Maintenance
Help Line: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Visit the Craftsman web page: www.sears.com/craftsman
972000-670
3-99
• Safety
• Features
USA
• PartsList
_®
NRTL
•
Warranty .........................................................................................................................................................
•
Introduction and Product Specifications .........................................................................................................
•
Rules For Safe Operation ...........................................................................................................................
•
A. Important Safety Rules For Battery Tools ..............................................................................................
B. Important Safety Instructions For Charger .............................................................................................
C. Important Information For Recharging Hot Batteries .............................................................................
Accessodes ....................................................................................................................................................
4
4
5
6
•
Features .........................................................................................................................................................
6
•
•
Operation .....................................................................................................................................................
Maintenance .................................................................................................................................................
•
Battery Pack Removal and Preparation For Recycling ................................................................................
12
•
Exploded View and Repair Parts List ...........................................................................................................
13
•
Parts Ordering/Service
14
...............................................................................................................................
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
318 in. CORDLESS
2
2
3-5
7-11
12
DRILL
If this £RRFTSNRN'3/8 in. Cordless Drill fails to give complete satisfaction within one year from the date of
purchase, RETURN IT TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will replace it,
free of charge.
If this I;RRFTSMRN'3/8 in. Cordless Drill is used for commerciar
90 days from the date of purchase.
or rental purposes, this warranty applies for onry
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck
and Co., Dept. 817WA, Hoffman
Estates,
Your drill has many features for making drilling
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
priority in the design of this drill making it easy to
maintain and operate.
_k
IL 60179
SPECIFICATIONS:
Chuck Capacity
Motor
Charger Rating
No Load Speed
Switch
CAUTION: Carefully read through this entire
owner's manual before using your new drill. Pay
close attentionto the Rules For Safe Operation,
Warnings and Cautions. If you use your drill
properly and onlyfor what it is intended, you will
enjoy years of safe, reliable service.
Charge Rate
Maximum Torque
2
3/8 in.
6.0 Volt DC
120 Volts, 60 Hz, AC Only
300 / 500 RPM
Two Speed / Reversible
3 Hours
45 in. Ibs.
The purpose of safety symbols Is to attract your attention to possible dangers, The safety symbols, and
the explanations with them, deserve your careful attention end understanding. The safety warnings do
not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL
MEANING
A
SAFETY ALERT SYMBOL:
A
WARNING: Failure to obey a safety warningcan result in serious injury to yourself or to others.
Always follow the safety precautionsto reduce the risk of fire, electricshock and personal injury.
A
CAUTION: Failure to obey a safety warningmay resultin propertydamage or personalinjuryto
yourselfor to others. Always followthe safety precautionsto reduce the risk of fire, electricshock
and personalinjury.
NOTE:
Advisesyou of informationor instructionsvital to the operationor maintenance of the equipment.
_k
Indicates warningor caution.May be used in conjunctionwith other symbolsor pictographs.
WARNING: Do not attempt to operate this
tool until you have read thoroughly and
understand completely all instructions,
safety rules, etc. contained in this manual.
Failure to comply can result in accidents
•
USE RIGHT TOOL. Don'tforce small toolor
attachment to do the job of a heavy duty tool.
Don't use tool for purpose not intended - for
example - A circular saw should never be used
for cuttingtree limbs or logs.
involving fire, electric shock, or serious
personal injury. Save owner's manual and
review frequently for continuing safe
operation, and instructing others who may
use this tool.
•
WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
movingparts and cause personal injury.Rubber
gloves and nonskidfootwear are recommended
when workingoutdoors.Wear protectivehair
coveringto contain long hair and keep it from
being drawn into nearby air vents.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read owner's
manual carefully.Learn its applicationsand
limitations as well as the specific potential
hazards related to this tool.
ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistantlenses;
they are NOT safety glasses.
PROTECT YOUR LUNGS. Wear a face mask or
dust mask if operation is dusty.
GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with groundedsurfaces.
For example: Pipes, radiators, ranges, refrigerator enclosures.
•
KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
•
AVOID DANGEROUS ENVIRONMENT,
use power tool in damp or wet locations
PROTECT YOUR HEARING. Wear hearing
protection during extended periods of operation.
SECURE WORK. Use clamps or a vise to hold
work. It's safer than using your hand and it frees
both hands to operate tool.
Don't
or
•
DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstablesupport.
•
MAINTAIN TOOLS WITH CARE. Keep tools
sharpat all times, and clean for best and safest
performance. Followinstructionsfor lubricating
and changing accessories.
expose to rain. Keep work area well lit.
•
KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area, Do not let visitors
contact tool or extension cord.
STORE IDLE TOOLS. When not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from
tool before turning it on.
DON'T FORCE TOOL. It willdo the job better
and safer at the rate for which it was designed.
3
RULES FOR SAFE OPERATION
(Continued)
l
NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparkingof the motor could
ignite flammable liquids,gases, or fumes.
DO NOT PLACE BATTERY TOOLS OR THEIR
BA'n'ERIES NEAR FIRE OR HEAT. They may
explode.
i
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
clothwhen cleaning. Never use brake fluids,
gasoline, petroleum-based productsor any
strong solvents to clean your tool.
DO NOT CHARGE BATTERY TOOL IN A
DAMP OR WET LOCATION.
i
STAY ALERT. Watch what you are doing and
use common sense. Do not operate tool when
you are tired. Do not rush.
i
CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefullychecked to determine that it
will operate propedyand perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting,and any other conditionsthat may
affect its operation.A guard or other part that is
damaged should be properly repaired or
replaced by an authorized service center unless
indicated elsewhere in this instruction manual.
Your battery tool should be charged in a location
where the temperature is more than 50°F but
less than IO0°F.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquidgets in your eyes, flush them
with clean water for at least 10 minutes, then
seek immediate medical attention.
If carrying your battery tool at your side, make
sure it is not running and your finger is not on the
switch. Avoid accidental starting.
SECURE WORK before applying power. NEVER
hold workpieca in your hand or across your legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
IMPORTANT
CHARGER
DRUGS, ALCOHOL_ MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger.
WARNING: To reduce risk of injury,charge only
nickel-cadmium type rechargeable batteries.
Other types of batteries may burstcausing
personal injuryand damage.
INSPECT FOR and remove all nails from lumber
before drilling.
IMPORTANT
TOOLS
FOR
SAVE THESE INSTRUCTIONS. This manual
contains importantsafety and operating
instructionsfor battery charger item number
9-11063.
DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BIT OR
CHUCK TO BECOME ELECTRICALLY LIVE.
Do not touch metal parts when drilling intoa wall;
grasp only the insulatedhandle(s) or plastic
housingwhen using this tool. Make sure hidden
electrical wiring, water pipes, and mechanical
hazards are not in the path of the bit when
drillinginto a wall.
•
SAFETY INSTRUCTIONS
Do not expose charger to rain or snow.
SAFETY RULES FOR BATTERY
Use of an attachment not recommended
or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to
persons.
Battery tools do not have to be plugged intoan
electrical outlet; therefore, they are always in
operating condition. Be aware of possible
hazards when not using your battery tool or
when changing accessories.
To reduce risk of damage to charger body and
cord, pull by charger body rather than cord when
disconnecting charger.
USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do not substitute any
other charger. Use of another charger could
cause batteriesto explode causing possible
serious injury.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwisesubjected
to damage or stress.
4
RULES FOR SAFE OPERATION
(Continued)
An extensioncord should not be used unless
absolutely necessary.Use of improper
extension cord could result in a risk of fire and
electric shock. If extension cord mustbe used,
make sure:
a.
That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b.
That extension cord is properly wired and in
good electrical condition; and
c.
That wire size is large enough for AC
ampere rating of charger as specified
below:
Cord Length (Feet) 25'
50' 100' 150'
Cord Size(AWG)
16
16
16
14
Note: AWG = American Wire Gage
DO NOT OPERATE CHARGER WITH A
DAMAGED CORD OR PLUG. If damaged,
_i,
Look for this symbol
safety is involved.
IMPORTANT
INFORMATION
to point out important
FOR
RECHARGING
have replaced immediately by a qualified
serviceman.
Do not operate charger if it has received a
sharp blow, been dropped, or otherwise
damaged in any way; take itto a qualified
serviceman.
•
Do not disassemble charger;take it to a
qualified serviceman when service or repair is
required. Incorrectreassembly may resultin a
risk of electric shock or fire.
•
To reduce risk of electric shock, unplugcharger
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
•
Do not use charger outdoors.
•
Disconnectcharger from powersupply when
not in use.
SAVE THESE INSTRUCTIONS. Refer to them
frequentlyand use them to instruct others who
may use this tool. If you loan someone this tool,
loan them these instructionsalso.
safety precautions.
It means attention!!!
Your
HOT BATTERIES
When using your drill continuously,the battedes in your battery pack will become hot. You shouldlet a hot
battery pack cool down for approximately 30 minutes before attempting to recharge.
Note: This situation only occurs when continuous use of your drill causes the batteries to become hot. It does
not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery
pack and charger to your nearest Sears repair center for electrical check.
_I,
WARNING:
The operation of any power tool can result in foreignobjects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
with side shields, available at Sears Retail Stores.
The following recommended accessoriesare currentlyavailable at Sears Retail Stores.
•
6°Pc, Extra Length Magnite Power Bit Set
•
Keyless Chuck (Item No.9.-20988)
•
30-Pc. Power Screwdriver/Nutdriver Set and Case
•
3/8 in. Chuck (Item No9_-2975)
•
17-Pc. Power Screwdriver/Nutdriver Set and Case
•
Chuck Key (Item No_-2053)
•
High Speed Bits (For Wood or Metal)...3/4 in. Max.
_kWARNING:
The use of attachments or accessories
not listed might be hazardous.
KNOW YOUR DRILL
See Figure 1.
WRIST STRAP
See Figure 1.
Beforeattempting to use any tool, familiarize yourself
with all operatingfeatures and safety requirements.
A wrist strap is provided to reduce the chances of
droppingyour drill. Place one hand through the wrist
,strap when carryingtool.
LEVEL
BATTERY
CHARGER
CHUCK
SWITCH
TRIGGER
CHUCKKEY
STORAGE
PACK
CHUCKKEY
WRISTSTRAP
INPUTJACK
,_
Fig. 1
WARNING: If any parts are missing,do not operatetool until the missingparts are replaced. Failureto do so
could result in possibleserious personal injury.
6
_k
_k
•
WARNING: Always wear safety goggles or
safety glasses with side shields when operating
tools, Failure to do so could result in objects
being thrown intoyour eyes, resultingin possible
serious injury.
DO not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
_k
WARNING: Do not allow familiaritywith your
drill to make you careless. Remember that a
careless fraction of a second is sufficientto inflict
severe injury.
CAUTION: Your drill'sbattery pack contains
special high temperature batteries to help
prevent battery damage when left on charge for
extended periodsof time. However, once the
batteries become fully charged, we recommend
that you unplug your charger from power supply
and disconnectit from the battery pack.
SWITCH
CHARGING
BATTERY PACK
See Figure 2.
The battery pack for this tool has been shipped in a
low charge conditionto prevent possible problems.
Therefore, you shouldcharge it at least 3 hours prior
to use.
To turn your drill ON, depress the switchtrigger.To
turn it OFF, release the switchtrigger.
SELECTOR
Note: Batteries willnot reach full charge the first time
they are charged. Allowseveral cycles (drilling
followed by recharging)for them to become fully
charged.
TO CHARGE
•
Charge battery pack only with the charger
provided.
•
Make sure power supply is normal house
voltage, 120 volts, 60 Hz, AC only,
Connect charger to battery pack by inserting
charger plug into inputjack. As shown in figure 1,
inputjack is located on the back side of battery
pack.
TWO SPEED
•
Note: Battery pack can remainon your drillor be
removedwhile charging.When battery pack is out
of the drill, be careful not to touchboth terminals
with a metal object.Touchingboth terminalswith a
metal objectwill short out the battery pack.
Yourdrill has a two speed feature in the switch.
Depress the switch trigger halfway for driving screws
at low speed. Depress the switchtrigger all the way
for normal drilling.Release the switchtrigger to trun
drilloff.
•
Connect charger to power supply.
•
The charge indicatorlight (LED), located on the
battery pack, will light up and glow when the
charger is properlyconnectedto power supply.
This lightindicatesthe charger is operating
properly.It will remain on untilcharger is
disconnectedfrom power supply.The light only
glowswhile your tool is charging,not during use.
The switch trigger can be locked in the OFF position.
This feature can be used to prevent the possibilityof
accidental startingwhen not in use. To lock switch
trigger, place the direction of rotation selector in
center position.
•
Afternormalusage,3 hoursofcharginglime isrequired
to be fully charged.
_,
•
"Fnebatterypackwillbecome slightlywarmto thetouch
whilecharging.Thisisnormalanddoesnotindicatea
problem.
•
Do not operate the tool while it is connected to the
charger.The driving abilitywill not increase.
•
CENTERPOSITION
(LOCK)
SWITCH
TRIGGER
Fig. 2
SWITCH LOCK
See Figure 2.
7
WARNING: Battery tools are always in
operating condition. Therefore, switch should
always be locked when not in use or carryingat
your side.
REVERSIBLE
TO INSTALL BATTERY PACK
See Figure 3.
•
This tool has the feature of being reversible. The
direction of rotation is controlled by a selector located
above the switch trigger. With the drill held in normal
operating position, the direction of rotation selector
should be positioned to the left of the switch for
drilling. The ddlling direction is reversed when the
selector is to the right of the switch. When the selector
is in center position, the switch trigger is locked.
_1
Lock switch triggeron your drillby placing the
direction of rotation selector in center position.
See Figure 3.
Place battery pack in your drill. Align raised db
inside drill with groove on battery pack. See
Figure 5.
•
CAUTION: To prevent gear damage, always
allow chuck to come to a completestop before
changing the direction of rotation.
To stop, release switch trigger and allow the chuck to
come to a complete stop.
SELECTOR
BATTERY
PACK
REVERSE
LATCHES
CENTERPOSITION
(LOCK)
FORWARD SWITCH
TRIGGER
DEPRESSLATCHES
Fig. 3
TO RELEASE
BATI'ERYPACK
CHUCK KEY
See Figure 4.
•
A chuck key has been provided for use when
installingor removing bits.
CHUCK KEY STORAGE
See Figure 4.
Fig. 5
Make sure the latches on each side of your
battery pack snap in place and battery pack is
secured in ddll before beginningoperation.
_b. CAUTION: When placing battery pack in your
drill, be sure raised rib inside drill aligns with
groove on battery pack and latches snap in place
properly. Improper assembly of battery pack can
cause damage to internalcomponents.
When not in use, the chuck key can be placed in the
storage area located on the front of the battery pack.
TO REMOVE BATTERY PACK
•
CHUCKKEY
•
•
PACK
TOREMOVECHUCKKEYFROMSTORAGE:
PULLOUTWARD(1), THENPULLDOWN(2) Fig. 4
8
Lock switch trigger on your drilr by placing the
direction of rotation selector in center position.
See Figure 3.
Locate latches on end of battery pack and
depress to release battery pack from your drill.
See Figure 5.
Remove battery pack from your drill.
INSTALLING
BITS
,_
See Figure 6.
•
Lookthe switch triggerby placingthe directionof
rotationselector in oenterposition. See Figure 3.
•
Open or close chuck jaws to a point where the
opening is slightlylarger than the bit size you
intend to use. Also, raise the front of your drill
slightlyto keep the bit from falling out of the chuck
jaws.
•
Insert drillbit into chuck the full length of the jaws
as shown in Figure 6.
DRILLBIT
WARNING: Do not insert drillbit intochuckjaws
and tightenas shownin figure 7. This couldcause
ddllbit to be thrownfrom drill resultingin possible
seriouspersonalinjuryor damage to the chuck.
CHUCK
REMOVING
BITS
See Figure6.
rotationselectorin center position,See Figure 3.
Lock the switchtriggerby placingthe directionof
Remove chuck key from storage. See Figure 4.
•
•
RIGHT
//
//
Fig. 6
•
Remove chuck key from storage. See Figure 4.
•
Using only the chuck key provided,tighten the
chuck jaws. Place chuck key in each of the three
holes and tighten in a clockwise direction.
•
Do not use a wrench to tighten or loosen the
chuck jaws.
•
Remove chuck key and return it to chuck key
storage.
Loosen the chuck jaws usingonly the chuck key
provided.
Do not use a wrenchto tighten or loosenthe
chuck jaws.
•
Remove drillbit from chuck jaws.
•
Remove chuck key and return it to chuck key
storage.
,_
WARNING: Always wear safety goggles or
safety glasses with side shields when operating
tools. Failure to do so could result in objects
being thrown intoyour eyes, resulting in possible
serious injury.
WARNING: Be prepared for binding or bit
breakthrough. When these situations occur,drill
has a tendency to grab and kick oppositeto the
direction of rotationand could cause loss of
controlwhen breakingthrough material. If not
prepared, this loss of controlcan result in
possibleserious injury.
DRILLING
See Figure 8.
When drilling metals, use a light oil on the drill bit to
keep it from overheating.The oil will prolongthe life of
the bit and increase the drillingaction.
If the bit jams in workpiece or if the drillstalls, release
switch triggerimmediately. Remove the bit from the
workpiece and determine the reason for jamming.
LEVEL DRILLING
See Figure 9.
A convenient feature provided with your ddll is a level.
It is recessed in the motorhousing on top of your drill.
It can be used to keep drill bits level during drilling
operations.
Fig. 8
When drilling hard smoothsurfaces use a center
punch to mark desired hole location.This willprevent
the drill bit from slipping off center as the hole is
started.
The material to be drilled shouldbe secured in a vise
or with clamps to keep it from turning as the drillbit
rotates.
Hold tool firmly and place the bit at the point to be
drilled. Depress the switch triggerto start tool.
Move the drillbit into the workpiece applying only
enough pressure to keep the bit cutting.Do not force
or apply side pressure to elongate a hole.
Fig. g
10
CHUCK REMOVAL
•
Insert alien wrench in chuck and tighten chuck
jaws securely. Tap sharply with a mallet in a
counterclockwise direction. This will loosen chuck
on the spindle, it can now be unscrewed by hand.
See Figure 12.
See Figures 10, 11, and 12.
The chuck must be removed in order to use some
accessories. To remove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position.
•
Insert a 5/16 inch or larger allen wrench(hex key
wrench)into the chuck of your drill and tighten the
chuck jaws securely.
•
Tap the alien wrench sharply with a mallet in a
clockwise direction. See Figure 10. This will
loosen the screw in the chuck for easy removal.
MALLET
CHUCK
CHUCKJAWS
Fig. 12
TO RETIGHTEN A LOOSE CHUCK
ALLEN
WRENCH
The chuck may become looseon spindle and develop
a wobble. Also, the chuck screw may become loose
causing the chuck jaws to bind and prevent them from
closing. To tighten, follow these steps:
Fig, 10
Open chuckjaws and remove allen wrench.
Remove the chuck screw by turning it in a clockwise direction. See Figure 11. Note: The screw
has left hand threads.
Fig. 11
11
•
Lock the switch trigger by placing the direction of
rotation serector in center position.
•
Insert allen wrench into chuck and tighten chuck
jaws securely. Tap allen wrench sharply with a
mallet in a clockwise direction. This will tighten
chuck on the spindle.
•
Open the chuck jaws and remove allen wrench.
•
Tighten the chuck screw. Note: The chuck screw
has left hand threads.
_IL WARNING:
Only the parts shown on parts list, page 13, are
intendedto be repaired or replaced by the customer.
All other parts should be replaced by a qualified
service technicianat an authorizedservice facility.
Avoid using solventswhen cleaning plastic parts.
Most plastics ere susceptibleto damage from various
types of commercial solventsand may be damaged
by their use. Use clean clothsto remove dirt, dust, oil,
grease, etc.
_lk
_k
Do not abuse power tools. Abusive practices can
damage tool as well as workpiece.
When servicing, use only identical
Craftsman replacement parts. Use of any other
part may create a hazard or cause product
damage.
WARNING: Do not at any time let brake fluids,
gasoline, petroleum-basedproducts, penetrating
oils, etc. come in contact with plastic parts. They
contain chemicals that can damage, weaken or
destroy plastic.
BA'I'rERIES
Your ddll's battery pack is equipped with 5 nickelcadmium rechargeable batteries. Length of service
from each charging will depend on the type of work
you are doing.
WARNING: Do not attempt to modifythis tool or
create accessories not recommendedfor use
with this tool. Any such alterationor modification
is misuse and could resultin a hazardous
conditionleadingto possibleserious personal
injury.
To obtain the longest possible battery life, we suggest
the following:
•
Store and charge your batteries in a cool area.
Temperatures above normal room temperature
will shorten battery life.
•
Never store batteries in e discharged condition.
Recharge them immediatelyafter they are
discharged.
•
All batteries gradually lose their charge. The
higher the temperature the quicker they lose their
charge. If you store your tool for long periods of
time without using it, recharge the batteries every
month or two. This practice will prolong battery
life.
The batteries in this tool have been designed to
provide maximum trouble free life. However, like all
batteries, they will eventually wear out. Do not
disassemble battery pack and attempt to replace the
batteries. Handling of these batteries, especially when
wearing rings and jewelry, could result in a serious
burn.
BATrERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
To preservenaturalresources,please
recycleor disposeof properly.
This productcontains nickelcadmium batteries. Local, state or
federal laws may prohibitdisposalof
nickel-cadmiumbatteries in ordinary
trash,
_IL WARNING: Upon removal, cover the battery
pack's terminals with heavy duty adhesive tape.
Do not attempt to destroy or disassemble battery
pack or remove any of its components. Nickelcadmium batteries must be recycled or disposed
of properly.Also, never touch both terminals with
metal objects and/or body parts as shortcircuit
may result. Keep away from children.Failure to
comply with these warnings could result in fire
and/or serious injury.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
12
CRAFTSMAN
I
318 INCH CORDLESS
DRILL - MODEL NO. 315.111610
number in all correspondenceregardingyour 3/8 in. CORDLESS DRILL or when ordering repair
The
modelnumberwiUbefoundon a plate attached tothe motorhousing.Always mentionthe model
parts.
SEE SACK PAGE FOR PARTS ORDERING
INSTRUCTIONS
3
2
5
4
PARTS LIST
Pad
Number
Description
1
616478-003
Screw (Special) ............................................. 1
2
3
973101-001
614984-001
Chuck (Item No. 9-2975) ............................... 1
Chuck Key (Item No, 9-2053) ........................ 1
4
973572-005
Battery Pack .................................................. 1
5
967215-001
Wrist Strap ..................................................... 1
972000-670
Battery Charger (Item No, 9-11081) ............. 1
Owner's Manual
Key
No.
6
* Can Be Purchased Thru RSOS (Retail Special Order System)
13
Quan.
}
For in-home major brand repair service:
Call 24 hours a day, 7 days a week
1-800-4-MY-HOME s" (%800-469-4663)
Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811
In Canada for all your service and parts needs call
Au Canada pour tout le service ou les pi_ces - 1-800-665-4455
For the repair or replacement parts you need:
Call 6 am - 11 pm (3ST, 7 days a week
PartsDirectsM
1-808-366-PART
(1-800-366-7278)
Para ordenar piezas con entrega a domicilio - 1-800-659-7084
For the location of a Sears Parts and Repair Center in your area:
Call 24 hours a day, 7 days a week
1-800-488-1222
For information on purchasing a Sears Maintenance Agreement
or to inquire about an existing Agreement:
Call 9 am - 5 pm, Monday - Saturday
1-800-827-6655
HomeCentral
The Service Side of Sears