Saniclean Excellence User manual

EXCELLENCE
USER MANUAL
INSTRUCTION
SAFETY PRECAUTIONS
NAME OF PARTS
OPERATING INSTRUCTIONS
INSTALLATION INSTRUCTION
DAILY MAINTENANCE
FAULT RECOGNITION
TECHNICAL SPECIFICATIONS
WARRANTY CERTIFICATE
SAFETY PRECAUTIONS
Please pay attention to these informations and only use SANICLEAN® as recommended
in the precaution for use.
Please respect all recommendations for your own safety and the safety of other users.
THE NON RESPECT OF ONE OF THESE RECOMMENDATIONS COULD OCCUR SERIOUS
INJURY FOR USER OR IMPORTANT DAMMAGE ON THE PRODUCT
N°1
Never splash water or liquid on
SANICLEAN®’s control panel.
N°3
N°2
Check the electricity voltage of
the circuit is 220-240V~. The
connecting circuit and the outlet
have to be conform to the CE
norms. Only use the SANICLEAN®
on 220-240V~ circuit.
If your outlet is not conform to CE
recommendation, please immediately contact a qualified and
authorised
electrician
to
replaced the outlet.
If the connection cable seems to
be damaged, do not plug the
cable and immediately contact
our after sales service in order
they can replaced it.
N°4
N°5
N°6
Never plus or unplug
the product with wet hands.
Remove any foreign elements
from the connection cable and
from the outlet in order to avoid
fire risk.
Never plug the product on a loosing electric outlet.
Please respect all these recommendations to use the
SANICLEAN®.
N°1 If your SANICLEAN® is not use for a long period, please
unplug the connection cable and drain the water from the tank.
N°2 Never install your SANICLEAN® where there is direct ray of
light. It may results a change of the product’s color.
N°3 Veiller à ne pas uriner sur les buses de lavage ou sur le
séchoir.
N°4 Never urinate directly on the nozzle or on the drying outlet.
N°5 Never lean against the coverlid when you sit on the
SANICLEAN®.
N°6 We recommend you to unplug the SANICLEAN® when there
is lightening and thunder.
N°7 Never connect your SANICLEAN® in a room where the
temperature can be negative in order to avoid the water in the
tank froze.
N°8 Always pay attention to soft use your SANICLEAN® and to
avoid using excessive force to close the lid or the seat.
N°9 Never use or leave your SANICLEAN® in a room exposed to
excessive moisture.
N°10 Never stand or put heavy object on the seat coverlid in
order to avoid breaking it.
N°11 Never use your SANICLEAN® in a wet room. Only use it on a
toilet that is conform to CE norm.
N°7
N°8
N°9
Never connect other product on
the SANICLEAN®’s outlet to avoid
sharing outlet.
Never splash water or any liquid
on the connection cable and
main unit.
Never connect the product to an
industrial water supply line. Only
connect to your home potable
water network.
N°10
N°11
N°12
Always unplug the SANICLEAN®
prior to clean.
Never try to disassemble, repair or
remodel the SANICLEAN® yourself.
Please always contact our after
sales service. If you do not respect
this point, the Warranty will be
stopped and cancelled.
Never keep any flammable materials on and close to the
SANICLEAN® (cigarettes,…).
N°14
N°13
If an invalid person not able to
adjust the temperature by itself,
could use the SANICLEAN®,
please always check that the
temperature of water, air and seat
are always at the level 2 not more.
This will prevent any trouble du
to high temperatures.
Never insert or put anything that
could obstruct the dryer outlet.
N°15
N°16
N°17
Never lift or close the seat and
the lid using excessive force in
order to avoid breaking the soft
closing system.
Never apply excessive force on
the operation panel and never
put heavy object on it. This will
avoid breaking the control panel.
Never strain or bend the water
supply connection hose in order
to avoid water leakage.
-- 2 --
NAME OF PARTS
Infrared receiver
Trim
Remote control
Lamp
Valve
Filter
Bidet
Mp3 interface
(No function for w660)
Seat cover pad
Seat cover
Warning labels within
Leakage protection plug
Operation panel
Infrared receiver
Stainless nozzle
Seat
Seat cushion
Tip : please do not cover
the infrared receiver,
otherwise the function
will be destroyed.
OPERATION INSTRUCTION
1 INSTRUCTION OF OPERATION PANEL
When seated, press «dry/flush» button to start water flush function.
After 6 seconds, it will start dry function.
> After 3 mins, dry function will stop automatically. Press «dry/flush» button again to
continue using. Press «stop» button to stop using.
> When nobody seated, press «dru/flush» button to start water flush function.
> When power outage, «dry/flush» button can start flush function.
WOMAN
/ MOVE
WASH
/ MOVE
When seated, press «woman/move» button, feminine cleaning nozzle is extended to
start reciprocating self-cleaning. Press «woman/move» button again, nozzle stops
moving reciprocatly and starts self-cleaning in the fixed position.
> while cleaning, press «stop» button to stop feminine cleaning function. If the «stop»
button is not pressed, the feminine cleaning will stop automatically after 60 seconds.
When seated, press «wash/move» button, posterior cleaning nozzle is extended to start
reciprocating self-cleaning. Press «wash/move» button again, nozzle stops moving
reciprocatly and starts self-cleaning in the fixed position.
> while cleaning, press «stop» button to stop posterior cleaning function. If the «stop»
button is not pressed, the posterior cleaning will stop automatically after 60 seconds.
Press «stop» button and stop the following functions : posterior, feminine, dry, nozzle
cleaning.
While the function of posterior, feminine, dry, nozzle cleaning is working, if the «stop» button
is not pressed, the dry function will stop automatically after 3 mins, other functions will stop
after 60 seconds.
2 REMOTE CONTROL FUNCTIONS
Water temperature
Battery display
Seat temperature
Posterior cleaning
Room temperature
Feminine cleaning
Dry
Transmit signal
Water temperature gear
Seat temperature gear
Cleaning strength display
Wide cleaning
Press “stop” button to stop all function.
If the “stop” button is not pressed, the dry function will stop automatically after 3 mins,
other functions will stop after 60 seconds..
WASH
/ MOVE
WOMAN
/ MOVE
When seated, press “wash/move” button, posterior cleaning nozzle is extended to the right position to
start the reciprocating self-cleaning. Press “wash/move” button again, nozzle stops moving reciprocatly
and starts self-cleaning in the fixed position.
While cleaning, press “stop” button to stop cleaning function. If the “stop” button is not pressed, posterior
function will stop automatically after 60 seconds.
When seated, press “woman/move” button, feminine cleaning nozzle is extended to the right position to
start the reciprocating self-cleaning. Press “woman/move” button again, nozzle stops moving reciprocatly
and starts self-cleaning in the fixed position.
While cleaning, press “stop” button to stop feminine function. If the “stop” button is not pressed, feminine
function will stop automatically after 60 seconds.
When seated, press “wide cleaning” button, cleaning nozzle is extended to start the reciprocating
wide-cleaning. Press “wide cleaning” button again, nozzle stops moving reciprocatly and starts
wide-cleaning in the fixed position.
While cleaning, press “stop” button to stop cleaning function. If the “stop” button is not pressed, posterior
function will stop automatically after 60 seconds.
When seated, press “dry” button to dry cleaning position. Dry function starts working.
After 3 mins, it will stop automatically.
If you want to continue using, press “dry” button again. Press the “stop” button to stop dry function while
it is working..
Adjust gear : when using functions of posterior, feminine, wide-cleaning, press “adjust” button to adjust
“high, middle, low” gear, set the gear and save it at the same time. While using dry function, press “adjust”
button tu adjust “air temperature” as “high, middle, low” gear, set the gear and save it at the same time.
Press “light” button, shimmer light makes more convinient to go to toilet in the night.
Press “light” button again to extinguish the shimmer light.
Press the “nozzle cleaning” button, the nozzle starts self-cleaning automatically. It will stop after 60
seconds. Press the “nozzle cleaning” button twice, nozzle is extended to do manual cleaning.
If you want to stop nozzle cleaning, press the “stop” button to stop.
(Tip : when start dry function, nozzle cleaning can’t work.)
Moving : while using the functions of posterior, feminine, wide-cleaning, press the “front” and “back”
button, can adjust the cleaning position of front and back.
Press “seat temp” button and adjust seat temperature.
s LIGHT OFF NORMAL TEMPERATURE
s GREEN LIGHT LOW TEMPERATURE ­#
s ORANGE LIGHT MIDDLE TEMPERATURE ­#
s RED LIGHT HIGHT TEMPERATURE ­#
Press “water temp” button and adjust water temperature.
s LIGHT OFF NORMAL TEMPERATURE
s GREEN LIGHT LOW TEMPERATURE ­#
s ORANGE LIGHT MIDDLE TEMPERATURE ­#
s RED LIGHT HIGHT TEMPERATURE ­#
While using the functions of posterior, feminine, auto wash, press “massage” button to start massage,
press “massage” button again, to stop massage. At the same time, the flow of water restores normal
cleaning mode. Massage flow of water based on “high-low-high” mode starts cycle changes.
Press “auto flush” button to flush toilet.
3 QUICK INSTRUCTION
Quick instruction 1 :
Cleaning position
Quick instruction 2 :
Massage cleaning
Quick instruction 3 :
Fixed position
cleaning
Choose the button to use
1
2 Press
button, nozzle is extended.
3 Press
button, nozzle is moving back.
1
2 Press
button, start massage-cleaning function.
3 Press
button again, stop massage-cleaning function.
Choose the button to use
1
2 Press (the function used in 1) button, nozzle stops reciprocating.
3 Press (the function used in 1) button again, nozzle starts reciprocating.
TIP : when seated, stick to back side of bidet, in order to sit a right position, and reduce to waste cleaning water.
INSTALLATION INSTRUCTION
1 INSTALL UPPER AND LOWER BODY
Inlet water interface
Inlet water valve
1) Connect inlet water interface to
inlet water valve and screw-up
through the other side of inlet water
valve in the inlet water mounting hole.
Inlet water mounting hole
Bait
2) Using two hooks to install
upper and lower body.
2 REMOTE CONTROL INSTALLATION
1) Use electric drill to drill two holes in the wall.
Remote control
2) Use anchoring to fix remote control pylon
in the wall.
Remote control pylon
3) Install remote control to pylon.
Anchoring
3 BIDET INSTALLING
a Flange ring installing
b Evacuation pipe installation
Main unit
Evacuation
Pipe
Main unit
Flange ring
Flange ring
The seal must be perfect to operate the flush.
Without perfect seal flushing of the device
will not work correctly
Main unit
Flange ring
The seal must be perfect when installing the pipe
because of the syphonic flushing system
that can only operates with 100% Airproof.
3) Stick the main unit
on the ground with an adapted
stick or cement.
Bidet
Floor
4) Tighten the screw into the ground.
Toilet
evacuation
185 mm
BE CAREFUL: The pressure of your existing water
network should be at least 20 l/mn in order the
Shower toilet can operate for washing and flushing.
Sluice valve installing
and flow adjusting
Inlet water valve
Use screwdriver to rotate right
2) If water pression is high, use screwdriver to
rotate right to reduce water pressure.
1) Connect inlet water valve to sluice valve and tighten.
3) Open your network water and the water
valve to supply water to the main unit.
4 TURN ON THE POWER OF BIDET
1) Thrust protective leakage valve to socket of 220V/50HZ,
and make sure grounding-type receptacle.
2) Try to test if every functions are normal.
3) Clean foreign matter when finish installing.
DAILY MAINTENANCE
1 TEST POWER LINE
Please have to check power plug. (Once or twice one month)
Press power button (on), and confirm if the lamp is shining.
Press power plug, and restart button again to confirm if the lamp turns off.
2 CLEANING STRAINER
Please have to check strainer. (Once or twice one month)
2) Revolve strainer the right side.
1) Use screw-driver turn off sluice valve
stop water comes in
3) Clean sewage of strainer.
4) Install strainer again and screw up..
5) Use screw-driver open valve,
and make sure if the strainer is leakage.
3 #,%!. $%/$/2):!4)/. 342!).%2
1) Pull the strainer out.
2) Use toothbrush to clean strainer.
3) Install the strainer to original place.
./::,% #,%!.).'
1) Press “nozzle cleaning” button in remote control to start nozzle
cleaning.
Tip : the bidet has automatically flush function : before and after
posterior and feminine function.
2) Press the “nozzle cleaning” button twice, nozzle is
extended, can clean by hands.
Use toothbrush to clean nozzle.
3) Press “stop” button to take back nozzle.
5 BIDET CLEANING
WARNING !
Before cleaning the main unit, turn off the OFF button and unplug the toilet.
1) Use a soft sweet sponge to clean the main unit.
2) Never use aggressive product or any detergent to clean the main unit.
3) When you clean the floor around the main unit,
avoid splashing water on the main unit to protect it.
4) Check that the Remote control receiver
on the main unit is always clean to avoid connection
problem between the main unit and the remote control.
FAULT RECOGNITION
Please confirm following items before entrust to repair.
ERROR PHENOMENON
Function error
Water does not come
out from nozzle
Flow of water
is not strong
Temperature of cleaning water
is not enought
Seat is not heated
Dry air temperature is low
Dry function does not work
Wash function does not work
Remote control
does not work
Bidet can not flush
automatically
CONFIRM REASON
TROUBLE SHOOTING
If electric alimentation is plug-in ?
Plug-off and plug-in alimentation.
If the water is cut off ?
Wait to restore supply water.
If sluice valve is open ?
Open sluice valve.
If there are foreign matter
in the strainer ?
Clean strainer.
> read page 9
If inlet water valve is flexed
or blocked up ?
Remove inlet water valve to flex.
If the flow of water sets as low gear ?
According to instruction
to adjust flow water
> read page 5
If there are foreign matter
in the strainer ?
Clean strainer.
> read page 9
If the nozzle is blocked up
by foreign matter ?
Clean nozzle
> read page 10
If inlet water valve is flexed
or blocked up ?
Remove inlet water valve to flex.
If water temperature is setted
as low gear or normal gear ?
According to instruction to adjust
water temperature.
> read page 5
If seat temperature is setted
as low gear or normal gear ?
According to instruction to adjust
seat temperature.
> read page 5
If dry function is setted as low gear ?
According to instruction to adjust
air temperature.
> read page 5
If human body touches seat sensor ?
Please make sure the position
of seat sensor.
If human body touches seat sensor ?
Please make sure the position
of seat sensor.
If the battery is not enought ?
Change battery.
If infrared receiver is covered
by foreign matter ?
Clean foreign matter.
If the remote control is used right ?
Adjust control angle
of remote control.
Whether stops water supply or not ?
Wait to water supply.
Whether close sluice valve ?
Open sluice valve.
TECHNICAL
SPECIFICATIONS
These specifications are liable to change and evolve
for quality improvement without prior notice.
Name of the product :
Name of the model :
Power rating :
Power :
Certifications :
SANICLEAN
EXCELLENCE
220-240V~, 50/60Hz
1650W
CE - RoHs
Dimensions :
Weight :
Connection cable length :
82 x 44 x 58 cm
13 kg
1,5 m
Water inlet :
Needed water pressure :
Direct inlet flow type – Water home supply
mini 0,4 bars – maxi 7 bars
Quantity water / minute :
Wash :
Woman :
Water tank capacity :
Washing temperature :
Heated seat :
Drying :
Deodorisation :
User detection sensor :
Water proof grade :
6 litres
Up to 40°C (level 4)
Up to 40°C (level 4)
Up to 60°C (level 4)
catalyst deodorising system
Digital sensor
IPX4.
Safety devices :
thermal fuses, float switch, thermal sensor,
overheat protection device (bimetal).
20 mA within 0.3 second.
Short circuit protector :
-- 13 --
Max 0,7 litre / min
Max 0,7 litre / min
WARRANTY CERTIFICATE
Please fill in the blanks with the needed information of your warranty certificates immediately after installation.
In case of question to our after sales services they will be asked to you.
NAME OF THE PRODUCT :
NAME OF THE MODEL :
PRODUCT SERIAL
SANICLEAN
EXCELLENCE
(At the backside of the main unit) :
PURCHASING DATE :
WARRANTY :
MANUFACTURER or EXTENDED
The manufacturing warranty is provided within 1 year from the purchasing
date (on the invoice).
The warranty includes services and all needed spare parts.
The warranty is only valid if all needed elements are given with a copy of the
original invoice.
The warranty is valid for all defected parts resulting from manufacturing.
The warranty is not valid for parts damaged by the user or by installation non
conform to SANICLEAN SAS recommendations, for instance:
- If the product as been disassemble or repair by non official technician from
SANICLEAN SAS.
- The installation is not conforming to SANICLEAN recommendation.
- The use is not conforming to SANICLEAN precaution of use.
- The connection has been done on a non conforming plug.
- Or all other damages caused by a use or an installation that is not indicated in
the SANICLEAN User Manual.
The warranty includes freight cost (go and back) to SANICLEAN's after sales
service warehouse.
After SANICLEAN’s agreement, please send your product back to the following
address : (Except other instruction of our after sales service) :
SANICLEAN SAS
SERVICE APRES VENTE
55, rue Camille Pelletan
33150 CENON - FRANCE
Tél. : 05 56 81 56 72
THIS PRODUCT SHOULD NOT BE DISPOSED WITH OTHER HOUSEHOLD
WASTES AT THIS END OF ITS WORKING LIFE.
IN ORDER TO BE RECYCLE, PLEASE BRING YOUR PRODUCT IN A CERTIFIED
DECHETTERY.
YOU CAN CONTACT ANY SANICLEAN DEALER TO STUDY THE WAY TO ELIMINATE YOUR OLD SANICLEAN.
www.saniclean.fr
www.saniclean.fr