Seagate ST9250317AS - Momentus 5400 FDE 250 GB Hard Drive Product manual

Product Manual
Momentus 5400 FDE
®
ST9120826A
ST9100826A
ST980821A
ST960814A
ST940811A
100377037
Rev. C
August 2007
©2004-2007, Seagate Technology LLC All rights reserved.
Publication number: 100377037, Rev. C
August 2007
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate
Technology LLC in the United States and/or other countries. Momentus, SeagateSeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/
or other countries. All other trademarks or registered trademarks are the property of their
respective owners.
One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion
bytes when referring to hard drive capacity. Accessible capacity may vary depending on
operating environment and formatting. Quantitative usage examples for various applications
are for illustrative purposes. Actual quantities will vary based on various factors, including file
size, file format, features and application software. Seagate reserves the right to change,
without notice, product offerings or specifications.
Contents
1.0
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1
System requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
About Momentus 5400 FDE disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.1
Drive state upon shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.0
Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1
Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2
Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3
Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4
Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5
Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.7
Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.8
Time to ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.9
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.9.1
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.9.2
Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.9.3
Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.9.4
Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.10
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.10.1
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.10.2
Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.10.3
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.10.4
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.10.5
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.10.6
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.11
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.12
Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.13
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.14
Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.14.1
Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.14.2
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.14.3
FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.15
Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.16
Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.0
Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
Master/slave configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2
Cable-select option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Drive integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.1
Drive installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.2
Consumer usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5
Security Erase--ATA security commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.1
Security Thaw command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.2
Security Erase procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.3
Drive State after security erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Momentus 5400 FDE Product Manual, Rev. C
1
1
2
2
19
19
20
20
20
20
22
23
23
23
23
23
24
i
4.0
ATA interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
ATA interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.1
ATA interface specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.2
ATA Security policy exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.3
Additional technical notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.4
Drive Trust Mode supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.5
Full Disc Encryption support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.6
Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.7
Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.8
Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
26
27
28
29
30
31
35
38
5.0
Compatibility summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1
Installation considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
BIOS versions tested . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3
Operating system versions tested . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4
Compatibility test configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5
Software utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5.1
Third party software support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
39
40
41
41
41
42
6.0
Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
ii
Momentus 5400 FDE Product Manual, Rev. C
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Momentus 5400 FDE drive label example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Momentus 5400 FDE Product Manual, Rev. C
11
20
21
22
iii
iv
Momentus 5400 FDE Product Manual, Rev. C
1.0
Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate®
Momentus®5400 FDE drives:
• ST9120826A
• ST9100826A
• ST980821A
• ST960814A
• ST940811A
These drives provide the following key features:
• Trusted Drive technology including:
• Hardware Full Disc Encryption (FDE)
• Drive Trust security interface and ATA security interface
• Pre-boot authentication and initialization using the drive’s secure partition and Drive Trust API
• Encryption key escrow. Consult with your ISV.
• 5,400-RPM spindle speed and 8-Mbyte buffer combine for superior performance.
• Quiet operation. Fluid Dynamic Bearing (FDB) motor.
• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.
• Tunneling Magnetoresistive (TMR) recording heads.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Full-track multiple-sector transfer capability without local processor intervention.
• 800 Gs nonoperating shock and 250 Gs operating shock.
• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• The 3D Defense System™, which includes Drive Defense, Data Defense, and Diagnostic Defense, offers the
industry’s most comprehensive protection for disc drives.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Support for Read Multiple and Write Multiple commands.
• Support for autodetection of master/slave drives that use cable select (CSEL).
1.1
System requirements
The following hardware and software is required to use these drives.
Host system requirements:
• Windows XP with Service Pack 2 (or later) when utilizing the Windows Drive Trust API.
• System/BIOS that supports ATA Security commands.
Momentus 5400 FDE Product Manual, Rev. C
1
1.2
About Momentus 5400 FDE disc drives
The Momentus 5400 FDE contains drive trust technology providing Full-Disc Encryption (FDE) using proven
Triple DES (TDES) data encryption and decryption.
Feature list
• Automatically encrypts (and decrypts) all data on the drive
• Operations are performed with no measured performance loss
• All user data is encrypted on write operations and decrypted on read operations
Benefits
• Drive-level protection of data
• Drives that are stolen, taken out of service, or re-purposed remain fully protected
• Near instantaneous disposal and re-purposing of the drive (ensures that data from previous user is not
accessible by the new drive owner)
• Able to be deployed within a trusted computing environment
The drive encrypts every write operation and decrypts every read operation without user intervention. The
encryption and decryption is done on the drive itself, so there is a near-zero performance impact when the
drive writes and reads data. The performance-optimized encryption and decryption engine performs at the ATA
interface speed.
The purpose of full-disc encryption is to protect the data stored on the drive in the event that the host system is
lost or stolen. This assures the system owner that if their system is lost or stolen, their data will not be accessible without the correct credentials.
Having the encryption/decryption on the drive also provides the highest level of security for data because all
data, including the boot sector bytes, operating system, temp and even the swap files are encrypted at the
drive level.
The Momentus 5400 FDE contains two security interfaces:
1. The ATA Security Interface
This interface is provided for compatibility with the existing ATA Security Command Set. The ATA Security
Interface is active upon shipment and ready for use.
2. The Drive Trust Security Interface
This interface is provided to enable a robust enterprise-level security and management policy. Use of the
Drive Trust Security Interface requires additional software to manage the Drive Trust interface. Please contact your system or software provider for more details.
1.2.1
Drive state upon shipment
Upon shipment from the Seagate factory, the ATA Security Interface is enabled and functioning. The following
is the detailed state of the drive upon shipment.
• Full Disc Encryption (FDE) is active and functioning. All user data is encrypted on write and decrypted on
read.
• The user interface to the drive is active and all read and write commands are allowed.
• The ATA user password is null (no value).
• The ATA master password is set to the Security ID (SID).
• ATA Security is set to the unlocked state. No password is required to access the drive.
2
Momentus 5400 FDE Product Manual, Rev. C
The Momentus 5400 FDE drive may be integrated into the computer system in the same way you would integrate a non-FDE Momentus drive.
The encryption key is enabled and operational when the drive leaves the Seagate factory. No user id is
required to access the drive, so the data on the drive is accessible to anyone possessing the drive. The drive
will encrypt data without a user id.
Momentus 5400 FDE Product Manual, Rev. C
3
4
Momentus 5400 FDE Product Manual, Rev. C
2.0
Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate
ST9120826A, ST9100826A, ST980821A, ST960814A, and ST940811A model drives.
2.1
Specification summary
The specifications listed in this table are for quick reference. For details on specification measurement or
definition, see the appropriate section of this manual.
Table 1:
Specifications
Drive specification
ST9120826A
ST9100826A
ST980821A
ST960814A
ST940811A
Formatted Gbytes (512 bytes/sector)*
120
100
80
60
40
Guaranteed sectors
234,441,648
195,371,568
156,301,488
117,210,240
78,140,160
Bytes per sector
512
Physical read/write heads
4
4
3
2
2
Discs
2
2
2
1
1
Cache (Mbytes)
8
Recording density,
BPI (bits/inch typical)
778,000
Track density.
TPI (tracks/inch typical)
126,000
Areal density (Gbits/inch2 max)
98.2
Spindle speed (RPM)
5,400
Internal data transfer rate OD
(Mbytes/sec max)
42
I/O data-transfer rate
(Mbytes/sec max)
100
ATA data-transfer
modes supported
PIO modes 0–4
Ultra DMA modes 0–5
Height
9.5 +/-0.2 mm (0.374 +/-.008 inches)
Width
69.85 +/-0.25 mm (2.750 +/-0.010 inches)
Length
100.2 +/-0.25 mm (3.945 +/-0.010 inches)
Weight (typical)
100 grams (0.22 lb)
Average latency (msec)
5.6
Power-on to ready (sec typical)
3.5
Standby to ready (sec typical)
3.0
Startup current 5V (typical)
1.0 amps
Track-to-track seek time
(msec typical)
1.0 (read), 1.5 (write)
Average seek time (msec typical)
12.5
Average seek, read (msec typical)
12.5
Momentus 5400 FDE Product Manual, Rev. C
5
Table 1:
Specifications
Drive specification
ST9120826A
ST9100826A
ST980821A
Average seek, write (msec typical)
14.5
Full-stroke seek (msec)
22 (typical); 24 (max)
Seek power (typical)
2.0 watts
Read/write power (typical)
Read: 2.50 watts; Write: 2.50 watts
Idle mode (typical, low power)
1.40 watts
Standby mode
0.96 watts (typical)***
Sleep mode
0.96 watts (typical)***
Voltage tolerance (including noise)
5V ± 5%
Ambient temperature
5° to 55°C (operating), –40° to 70°C (nonoperating)
Temperature gradient
(°C per hour max, noncondensing)
20°C (operating)
30°C (nonoperating)
Relative humidity
(noncondensing)
5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max
Wet bulb temperature (°C max)
30°C (operating)
40°C (nonoperating)
Altitude, operating
–304.8 m to 3,048 m (–1000 ft to 10,000 ft)
Altitude, nonoperating
(below mean sea level, max)
–304.8 m to 12,192 m (–1,000 ft to 40,000 ft)
Shock, operating
(Gs max at 2 msec)
250
Shock, nonoperating
(Gs max at 2 msec)
800
Shock, nonoperating
(Gs max at 1 msec)
900
Shock, nonoperating
(Gs max at 0.5 msec)
400
Vibration, operating
(max displacement may
apply below 10 hz)
1.0 Gs (0 to peak, 5–500 Hz)
Vibration, nonoperating
(max displacement may apply
below 22 hz)
5.0 Gs (0 to peak, 10–500 Hz)
ST960814A
ST940811A
Drive acoustics, sound power (bels), 2
disc
Idle**
2.4 (typical)
2.6 (max)
Performance seek
2.9 (typical)
3.1 (max)
Nonrecoverable read errors
1 per 1014 bits read
Annualized Failure Rate (AFR)
0.73%
Load/Unload (U/UL) cycles
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
6
Momentus 5400 FDE Product Manual, Rev. C
Table 1:
Specifications
Drive specification
ST9120826A
ST9100826A
ST980821A
ST960814A
ST940811A
Warranty
5 years on distribution units.
To determine the warranty for a specific drive, use a web browser to access the following web
page:
www.seagate.com/support/service/
From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive
serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur, according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby
modes will not contribute to battery power consumption.
2.2
Formatted capacity
Model
Formatted capacity*
Guaranteed sectors
Bytes per sector
ST9120826A
120 Gbytes
234,441,648
512
ST9100826A
100 Gbytes
195,371,568
512
ST980821A
80 Gbytes
156,301,488
512
ST960814A
60 Gbytes
117,210,240
512
ST940811A
40 Gbytes
78,140,160
512
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
2.3
Default logical geometry
Cylinders
Read/write heads
Sectors per track
16,383
16
63
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
2.4
Physical organization
Model
Read/write heads
Number of discs
ST9120826A
4
2
ST9100826A
3
2
ST980821A
3
2
ST960814A
2
1
ST940811A
2
1
Momentus 5400 FDE Product Manual, Rev. C
7
2.5
Recording and interface technology
Technology
Specification
Interface
Parallel ATA
Recording method
RLL 0,11
Recording density BPI (bits/inch typical)
778,000
Track density TPI (tracks/inch typical)
126,000
Areal density (Gbits/inch2 max)
98.2
Spindle speed (RPM) (± 0.2%)
5,400
Internal data-transfer rate OD (Mbytes/sec max)
42
I/O data-transfer rate (Mbytes/sec max)
100 (Ultra DMA mode 5)
Interleave
1:1
Cache buffer
8 Mbytes (8,192 kbytes)
2.6
8
Physical characteristics
Height
(mm)
(inches)
9.5 +/–0.2
0.374 +/–0.008
Width
(mm)
(inches)
69.85 +/–0.25
2.750 +/–0.010
Length
(mm)
(inches)
100.2 +/–0.25
3.945 +/–0.010
Typical weight
(grams)
(pounds)
100
0.22
Momentus 5400 FDE Product Manual, Rev. C
2.7
Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using
drive diagnostics. The specifications below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between
random tracks, less overhead.
Typical seek times (msec)*
Read
Write
Track-to-track
1.0
1.5
Average
12.5
14.5
Full-stroke
22.0
24.0
Average latency
5.56
5.56
*Measured in performance mode
Note.
2.8
These drives are designed to consistently meet the seek times represented in this manual. Physical seeks,
regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values.
However, due to the manner in which these drives are formatted, benchmark tests that include command
overhead or measure logical seeks may produce results that vary from these specifications.
Time to ready
Time to ready
Typical
Max @ 25°C
Power-on to Ready (sec)
3.5
8.0
Standby to Ready (sec)
3.0
8.0
Momentus 5400 FDE Product Manual, Rev. C
9
2.9
Power specifications
The drive receives DC power (+5V) through the interface connector.
2.9.1
Power consumption
Power requirements for the drives are listed in the table on page 10. Typical power measurements are based
on an average of drives tested, under nominal conditions, at 25°C ambient temperature.
• Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Seek mode
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does
not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on
three random seek operations every 100 msecs. This mode is not typical.
• Read/write power and current
Read/write power is measured with the heads on track, based on three 63 sector read or write operations
every 100 msecs.
• Idle mode power*
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in
a random track location.
• Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/
write electronics are in power-down model
Table 2:
DC power
Power dissipation
+5V average (25° C)
Spinup (typical)
1.0 amps
Seek
2.00 watts
Read
2.50 watts
Write
2.50 watts
Idle, performance mode*
1.90 watts
Idle, active*
1.70 watts
Idle, low power mode*
1.40 watts
Standby
0.96 watts
Sleep
0.96 watts
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
10
Momentus 5400 FDE Product Manual, Rev. C
2.9.1.1
Typical current profile
Figure 5. Typical 5V startup and operation current profile
2.9.2
Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on
the +5 volt line.
Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave
injected noise at up to 10 MHz.
Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.
2.9.3
Voltage tolerance
Voltage tolerance (including noise):
5V ± 5%
Momentus 5400 FDE Product Manual, Rev. C
11
2.9.4
Power-management modes
The drive provides programmable power management to provide greater energy efficiency. In most systems,
you can control power management through the system setup program. The drive features the following
power-management modes:
Table 3:
Power management modes
Power modes
Heads
Spindle
Buffer
Active (operating)
Tracking
Rotating
Full power
Idle, performance
Tracking
Rotating
Self refresh—low power
Idle, active
Floating
Rotating
Self refresh—low power
Idle, low power
Parked
Rotating
Self refresh—low power
Standby
Parked
Stopped
Self refresh—low power
Sleep
Parked
Stopped
Self refresh—low power
• Active mode
The drive is in Active mode during the read/write and seek operations.
• Idle mode
The buffer remains enabled in performance mode, and the drive accepts all commands and returns to Active
mode any time disc access is necessary.
• Standby mode
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the
standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a
specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby
mode, the drive buffer is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest.
The drive accepts all commands and returns to Active mode any time disc access is necessary.
• Sleep mode
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer
is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest. The drive leaves Sleep
mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep
mode and enters Standby mode with all current translation parameters intact.
• Idle and Standby timers
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and
begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive
activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive
accepts all commands and returns to Active mode when disc access is necessary.
12
Momentus 5400 FDE Product Manual, Rev. C
2.10
Environmental specifications
2.10.1
Ambient temperature
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions.
Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.
Operating
Nonoperating
2.10.2
5° to 55°C (41° to 131°F)
–40° to 70°C (–40° to 158°F)
Temperature gradient
Operating
20°C per hour (68°F per hour max), without condensation
Nonoperating
30°C per hour (86°F per hour max), without condensation
2.10.3
Humidity
2.10.3.1
Relative humidity
Operating 5% to 90% noncondensing (30% per hour max)
Nonoperating 5% to 95% noncondensing (30% per hour max)
2.10.3.2
Wet bulb temperature
Operating 30°C (86°F max)
Nonoperating 40°C (104°F max)
2.10.4
Altitude
Operating
Nonoperating
2.10.5
–304.8 m to 3,048 m (–1,000 ft to 10,000 ft)
–304.8 m to 12,192 m (–1,000 ft to 40,000 ft)
Shock
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive
mounting screws. Shock may be applied in the X, Y or Z axis.
2.10.5.1
Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum
operating shock of 250 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more
than two times per second.
Momentus 5400 FDE Product Manual, Rev. C
13
2.10.5.2
Nonoperating shock
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse
of 2 msec duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 900 Gs based on a nonrepetitive half-sine shock pulse
of 1 msec duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 400 Gs based on a nonrepetitive half-sine shock pulse
of 0.5 msec duration.
2.10.6
Vibration
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the
drive mounting screws. Vibration may be applied in the X, Y or Z axis.
2.10.6.1
Operating vibration
The following table lists the maximum vibration levels that the drive may experience while meeting the performance standards specified in this document.
5–500 Hz
2.10.6.2
1.0 Gs (0 to peak). Max displacement may apply below 10 Hz.
Nonoperating vibration
The following table lists the maximum nonoperating vibration that the drive may experience without incurring
physical damage or degradation in performance when subsequently put into operation.
5–500 Hz
2.11
5.0 Gs (0 to peak). Max displacement may apply below 22 Hz.
Acoustics
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially
free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.
Note.
For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is
defined by the following equation:
(Number of seeks per second = 0.4 / (average latency + average access time)
Table 4:
Drive level acoustics
Idle*
Performance Seek
2.4 bels (typ)
2.6 bels (max)
2.9 bels (typ)
3.1 bels (max)
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
14
Momentus 5400 FDE Product Manual, Rev. C
2.12
Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in
performance when subjected to the radio frequency (RF) environments defined in the following table:
Table 5:
Electromagnetic immunity
Test
Description
Performance
level
Reference
standard
Electrostatic discharge
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV
B
EN 61000-4-2: 95
Radiated RF immunity
80 to 2,000 MHz, 10 V/m,
A
80% AM with 1 kHz sine
900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz
EN 61000-4-3: 96
Electrical fast transient
± 1 kV on AC mains, ± 0.5 kV on external I/O
B
EN 61000-4-4: 95
Surge immunity
± 1 kV differential, ± 2 kV common, AC mains
B
EN 61000-4-5: 95
Conducted RF immunity
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz
sine
A
EN 61000-4-6: 97
Power Frequency H-field
immunity
1 A/m, 50Hz/60Hz, 3 axes
A
EN 61000-4-8: 97
Voltage dips, interrupts
30% Reduction for 25 cycles
>95% Reduction for 250 cycles
>95%, 0.5 cycles
C
C
B
EN 61000-4-11: 94
ENV 50204: 95
A - 1) No upset or degradation in performance beyond manufacturer’s specified limits.
2) No data loss.
B - 1) Unit self recovers without user intervention.
2) No data loss.
C - 1) Upset OK provided that unit will function after user intervention.
Momentus 5400 FDE Product Manual, Rev. C
15
2.13
Reliability
Measurement type
Specification
Nonrecoverable read errors
1 per 1014 bits read, max.
Annualized Failure Rate (AFR)
0.73%
Load/Unload (U/UL)
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Warranty
5 years on distribution units.
Important: When returning a drive for warranty support, if possible, you should
provide the valid ATA Master password, or return the drive in the Security Erased
state with the User Data Area accessible.
If these recommendations are not followed, Seagate cannot access the drive to
perform failure analysis to verify your warranty claim.
To determine the warranty for a specific drive, use a web browser to access the
following web page:
www.seagate.com/support/service/
From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
2.14
Agency certification
2.14.1
Safety certification
The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections
of IEC950 and EN 60950 as tested by TUV North America.
2.14.2
Electromagnetic compatibility
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product
standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and
the immunity levels are defined by EN 55024.
Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous
paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply
with the directives when used in the test systems, we cannot guarantee that all systems will comply with the
directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O
cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators
should confirm EMC compliance and provide CE marking for their products.
16
Momentus 5400 FDE Product Manual, Rev. C
Korean RRL
If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic
Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information
and Communication Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab.
• Family name: Momentus 5400.2
• Certificate numbers: E-D011-05-2395 (B)
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).
2.14.3
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached
as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification
of the device is required.
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total
assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is
likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio
and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television, which can be determined by turning the equipment on and off,
you are encouraged to try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission:
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.
Momentus 5400 FDE Product Manual, Rev. C
17
2.15
Environmental protection
Seagate designs its products to meet environmental protection requirements worldwide, including regulations
restricting certain chemical substances.
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical
substances, including Lead (Pb), in electronic products effective July 2006.
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the representations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our
supplier contracts require compliance with our chemical substance restrictions, and our suppliers document
their compliance with our requirements by providing material content declarations for all parts and materials for
the disc drives documented in this publication. Current supplier declarations include disclosure of the inclusion
of any RoHS-regulated substance in such parts or materials.
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws
and regulations which restrict chemical content in electronic products. These systems include standard operating procedures that ensure that restricted substances are not utilized in our manufacturing operations, laboratory analytical validation testing, and an internal auditing process to ensure that all standard operating
procedures are complied with.
2.16
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment. Users
should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive
chemicals as electronic drive component reliability can be affected by the installation environment. The silver,
copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
18
Momentus 5400 FDE Product Manual, Rev. C
3.0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
Momentus®5400 FDE drives can be connected to a computer system using a standard IDE interface cable and
power connector. The host system must support the ATA pass-through facility to successfully use these drives.
Additionally, in the Windows environment, users not having administrator rights on their user account will be
required to load a Seagate-supplied driver.
The following operating systems support the required pass-through facilities:
• Windows XP, Service Pack 2 (and later)
• Windows 2003 Server, Service Pack 1 (and later). This OS has not been tested by Seagate.
Momentus®5400 FDE drives may be used as boot drives when used with these operating systems.
3.1
Handling and static discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:
Caution:
• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s
exposure to ESD.
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire
installation procedure.
• Handle the drive only by its edges or frame.
• The drive is fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are
used to seal out dirt and contamination.
The sole exception to this statement is for the Momentus®5400 FDE perforated label which you should remove
and attach to the exterior of the computer system.
Momentus 5400 FDE Product Manual, Rev. C
19
3.2
Jumper settings
3.2.1
Master/slave configuration
Use the options jumper block shown in Figure 6 to configure the drive for operation. This jumper block is the
4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable
select option, see Section 3.2.2.
The “Master or single drive” option is the factory default setting.
Drive is master (or single drive)
Drive is slave
Cable select
Figure 6. Jumper settings
3.2.2
Cable-select option
Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28,
CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To
enable cable select, set a jumper as shown in Figure 6. Refer to your computer manual to determine whether
your computer supports this option.
3.3
Drive mounting
You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting
holes. See Figure 7 for drive mounting dimensions (dimensions in inches with mm in parentheses). Follow
these important mounting precautions when mounting the drive:
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.
• Use only M3 x 0.5 mounting screws.
• Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb).
• Four (4) threads (0.080 inches) minimum screw engagement recommended.
20
Momentus 5400 FDE Product Manual, Rev. C
3.945 +/-0.010
(100.2 +/-.25)
.157
(3.9878)
.399
(10.135)
0.490 +/- .010
(12.446 +/- .254)
0.673 +/- .010
(17.09 +/- .254)
Breather Hole
Do not cover
or seal.
2.750 +/- .010
(69.85 +/- .25)
Recommended case temp.
measurement location
3.567
(90.60)
.551
(13.99)
.374 +/- .008
(9.5 +/- .2)
2X M3 X 0.5-6H
Mounting holes
Both sides
.12 min. full thread
2X .118 (3.00)
Both sides
inches
(mm)
3.567
(90.60)
.551
(13.99)
4X M3 X 0.5-6H
Mounting holes
.10 min. full thread
2.430
(61.72)
.399
(10.135)
Detail A
Detail A
Figure 7.
.160
(4.06)
Mounting dimensions—top, side and end view
Momentus 5400 FDE Product Manual, Rev. C
21
3.4
Drive integration
The Momentus 5400 FDE may be installed in the target computer system in exactly the same way as a nonFDE Momentus drive with one optional exception regarding the label.
Momentus 5400 FDE
DO NOT COVER
BREATHER HOLE
X X X GB
This drive is manufactured by Seagate for OEM
distribution. For product information or technical
support, please contact your system OEM.
Product of Singapore
MIC
X-XXXX-XX-XXXX (B)
®
N176
D33027
excessive shock; do not push on
CAUTION: Avoid
top cover or remove any seal or label.
SN: XXXXXXXX
Model: ST9XXXXXA
+5V TBD A
PN: XXXXXX-XXX
JUMPERS
MASTER
FW: X.XX
SLAVE
Date: XXXXX
Site: XXX
CABLE SEL
SID: XXXX XXXX XXXX XXXX XXXX
SID: XXXX XXXX XXXX XXXX XXXX
SN: XXXXXXXX
Momentus 5400 FDE
Figure 8.
Momentus 5400 FDE drive label example
To install the drive in the system:
1. Remove the drive from the packaging material.
2. Remove the perforated sticker portion of the drive label (optional).
3. Remove the backing from the sticker (optional).
4. Apply the sticker to the outside of the computer for future reference (optional)
5. Install the drive in the computer system.
6. Load any desired images and operating system to the drive.
7. Install other components and options.
8. Set the original Master Password to a new value (see Section 1.2.1 for information about setting the SID)
utilizing System/BIOS or third party software (optional).
No password is required to change the Master password when the drive is in the unlocked state.
The drive remains in the unlocked state until a User password is set.
After the installation procedure is complete, the computer is ready to be shipped to the customer.
Note.
22
The manufacturer of the computer system (system integrator) does not have to enter any password.
Except for the label, the installation procedure for the Momentus 5400 FDE is exactly the same as the
Momentus 5400.2.
Momentus 5400 FDE Product Manual, Rev. C
3.4.1
Drive installation
Upon receipt by the consumer, the drive’s user interface is identical to a Momentus 5400.2 drive. The normal
ATA security commands are functioning and available for initialization of the password as follows:
Per normal ATA Security Commands specifications, the drive is unlocked and all ATA security commands and
all normal ATA commands may be issued.
1. Consumer accesses the computer manufacturer’s BIOS set-up screen.
2. Consumer selects option to set User Password.
After setting the User password, the drive is now under access control (locked) and will require a password
for future accesses.
3. Optional: Consumer selects the option to set the Master password from the BIOS choices.
4. Consumer exits the BIOS settings menu and continues with the boot process.
5. The BIOS enters the Security Freeze Command (F5) prior to exiting the boot sequence.
3.4.2
Consumer usage
After initialization, the consumer will just need to enter their User password each time the computer is booted
according to the following description:
1.
The computer system is turned on or the hardware is reset.
2. The drive reports to the BIOS that it is in the locked state per standard ATA Security Command reporting.
3. The BIOS queries the user for the password.
4. The BIOS supplies the password to the drive using the Security Unlock Command (F2).
5. The drive is unlocked and the BIOS may continue the booting process.
6. The BIOS enters the Security Freeze Lock Command (F5) prior to exiting the boot sequence.
3.5
Security Erase--ATA security commands
The Momentus 5400 FDE provides powerful features for cryptographically erasing the drive for disposal or
repurposing. The drive uses the ATA Security Erase Prepare (F3) and ATA Security Erase (F4) commands to
perform the cryptographic erase.
3.5.1
Security Thaw command
Most current laptop/notebook computer BIOS’s issue a Freeze Lock command to the drive during the boot process. This prevents issuing the ATA Security commands. To allow for secure erase, the Momentus 5400 FDE
has a new command named Security Thaw (F7). Issuing the Security Thaw command with either User or Master password supplied will remove the Freeze Lock from the drive.
3.5.2
Security Erase procedure
Using the Security Thaw command and the Security Erase commands, the drive may be cryptographically
erased according to the following procedure:
1. Consumer boots up the computer normally according to the Consumer Usage section above.
2. Consumer invokes software or BIOS option for Erase.
3. The software or BIOS queries the user for either the User or Master password.
4. The software or BIOS issues the Security Thaw command (F7) to the drive supplying the given password.
5. The drive removes the Freeze Lock--Security commands may now be issued.
Momentus 5400 FDE Product Manual, Rev. C
23
6. The software or BIOS issues the Security Erase Prepare (F3) command.
7. The software or BIOS issues the Security Erase Unit (F4) command.
Select the Enhanced erase for cryptographic erase that completes in less than one second.
3.5.3
Drive State after security erase
Upon completion of the erase sequence, all data is cryptographically erase and the drive has been returned to
the manufactured state as follows:
• The old encryption key is deleted.
• A new random encryption key has been created on the drive.
• Encryption function is active and functioning.
All user data is encrypted on write and decrypted on read, with the new key
• The user interface to the drive is active and all read and write commands are allowed.
• The ATA User password is reset to null (no value).
• The ATA Master password is not modified
The ATA Master password is the same value as it was before the erase.
• The ATA Security is set to the Unlocked state.
No password is required to access the drive.
The drive may now be disposed of safely, or the drive may be returned to service for another consumer following the initialization procedure defined above. Drives returned to Seagate for warranty purposes have special
requirements. See the warranty information in Section 2.13 for additional details.
24
Momentus 5400 FDE Product Manual, Rev. C
4.0
ATA interface
These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports
ATA programmed input/output (PIO) modes 0–4 and Ultra DMA modes 0–5. The drive also supports the use of
the IORDY signal to provide reliable high-speed data transfers.
For detailed information about the ATA interface, refer to the draft of AT Attachment with Packet Interface
Extension (ATA/ATAPI-7), NCITS T13, subsequently referred to as the Draft ATA-7 Standard.
4.1
ATA interface signals and connector pins
The following table summarizes the signals on the 44-pin ATA interface connector. For a detailed description of
these signals, refer to the Draft ATA-7 Standard.
Table 6:
Connector signals
Signal Name
Connector
Contact
Cable
Conductor
Cable
Conductor
Connector
Contact
Signal Name
RESET-
1
1
2
2
Ground
DD7
3
3
4
4
DD8
DD6
5
5
6
6
DD9
DD5
7
7
8
8
DD10
DD4
9
9
10
10
DD11
DD3
11
11
12
12
DD12
DD2
13
13
14
14
DD13
DD1
15
15
16
16
DD14
DD0
17
17
18
18
DD15
Ground
19
19
20
20
(keypin)
DMARQ
21
21
22
22
Ground
DIOW-
23
23
24
24
Ground
DIOR-
25
25
26
26
Ground
IORDY
27
27
28
28
PSYNC:CSEL
DMACK-
29
29
30
30
Ground
INTRQ
31
31
32
32
IOCS16-
DA1
33
33
34
34
PDIAG-
DA0
35
35
36
36
DA2
CS1FX-
37
37
38
38
CS3FX-
DASP-
39
39
40
40
Ground
+5 V (Logic)
41
41
42
42
+5V (Motor)
Ground (Return)
43
43
44
44
No connection
Momentus 5400 FDE Product Manual, Rev. C
25
4.1.1
ATA interface specifications
The Momentus 5400 FDE is consistent with the ATA Interface implementation of the Momentus 5400.2 products with the known exceptions listed within this section (Section 4.1.1 subordinate sections).
4.1.1.1
Legacy mode -- Multi-word DMA not supported
If multi-word DMA model is selected, the drive response is indeterminate, and the ATA bus will hang. Due to
this limitation, the drive will violate the DCO Set requirement in the ATA specification.
4.1.1.2
Legacy mode -- Interrupts disabled mode (polling) supports limited functionality
Interrupts disabled mode is entered upon setting of the nIEN bit to 1, in the Device Control Register as shown
in the ATA Specification.
Table 7:
Interrupts Disabled mode nIEN bit
7
6
5
4
3
2
1
0
HOB
r
r
r
r
SRST
nIEN
0
Upon entry of this mode the drive will behave normally in the absence of issuance of the following user data
access commands, to the drive:
• READ/WRITE BUFFER
• READ/WRITE SECTOR
• READ/WRITE SECTOR EXT
• READ/WRITE MULTIPLE
• READ/WRITE MULTIPLE EXT
• READ/WRITE DMA
• READ/WRITE DMA EXT
If any of the identified data access commands are issued to the drive, the drive will tri-state the data bus and
the retrieved data will be indeterminate. Additionally, the drive will return indeterminate values in the status register.
Upon entry into the described state, the drive will remain in this state until you power cycle the drive.
If the nIEN bit is set to 1 and none of the identified data access commands are issued, the nIEN bit may be
returned to 0 and the drive will continue with normal operation in the Interrupts Enabled mode.
4.1.1.3
PIO Read -- Interrupts Enabled mode
In the Interrupts Enabled mode, the drive has limited support for the host to check the status register of the
drive while waiting for the data transfer interrupt.
If the host polls the status register, while waiting for interrupts and the drive has not yet posted the interrupt, the
drive will tri-state the data bus. This limitation is only an issue for any host that might choose to transfer the
data prior to the DRQ bit being set. For instance, any host that reads a status of 0x20 may, based on the drive
Busy bit and Error bit being cleared, choose to transfer the data, even though the DRQ bit is not set. This is not
recommended host behavior, and, if implemented, would result in undesirable results.
This limitation is not an issue for hosts that simply wait for the interrupt to be posted.
This is not believed to be an issue for hosts that check status but wait for the DRQ bit to be set.
26
Momentus 5400 FDE Product Manual, Rev. C
4.1.1.4
Device 0 only configurations
Per the ATA-ATAPI-7, Rev. 4B specification, Clause 5.16.1 (see italicized excerpt below), the specification
expects Device 0 to return the Task File Register when Device 1 is selected as follows:
In a single device configuration where Device 0 is the only device and the host selects Device 1, Device 0
shall respond as follows:
...
If the device does not implement the PACKET Command feature set, a read of the Control Block or Command
Block registers, other than the Status or Alternate Status registers, shall complete as if Device 0 was selected.
A read of the Status or Alternate status register shall return the value 00h.
Under the described conditions, and the host selecting Device 1 in a Device 0 only configuration, the Momentus 5400 FDE will not respond for the request to Slave (Device 1) and the returned value will be indeterminate.
4.1.1.5
48-bit (Extended mode) Sector Count register must be written twice
Per the ATA-ATAPI-7, Rev. 4B specification, Clause 4.14:
In a device implementing the 48-bit Address feature set, the Feature register, the Sector Count register, the
LBA Low register, the LBA Mid register, and the LBA High register are each a two-byte deep FIFO. Each time
one of these registers is written, the new content written is placed into the “most recently written” location and
the previous content of the register is moved to “previous content” location.
When using the 48-bit Address feature set, the Momentus 5400 FDE assumes that the host will always write
the sector count register twice, even though the address may only require one write. Failure to write the sector
count register twice will result in the subsequent read likely hanging due to a mismatch in the sector count.
All registers identified above should always be written twice in when using the 48-bit Address Feature set.
4.1.2
ATA Security policy exceptions
In the ATA Security Interface mode, the drive conforms to the ATA Security Policy, except the following desirable exceptions to implement the desired Momentus 5400 FDE behavior:
Upon execution of the Secure Erase Sequence, the drive will have the following behavior:
• All modes of Secure Erase will instantaneously delete the encryption key rendering all user data unintelligible.
• A new encryption key will be generated inside the drive replacing the previous encryption key.
• The new encryption/decryption key will be applied to the data for all subsequent writes/reads prior to the
next Secure Erate sequence.
• The User password will be cleared to a null value.
• The Master password will retain the current value per the ATA specification.
Note.
On completion of this sequence, the user is assured that all sectors on the drive are unintelligible, and
the drive is returned to the default factory state. It is then immediately ready for disposal or re-purposing.
The ATA Security Erase Unit Command provides for normal and enhanced erase modes as follows:
Momentus 5400 FDE Product Manual, Rev. C
27
Table 8:
ATA Security Erase Unit bits
Word
Content
0
Control word
Bit 0
Identifier
0 = Compare User password
1 = Compare Master password
Bit 1
Erase mode
0 = Normal Erase
1 = Enhanced Erase
Bit (15:2)
1 - 16
Password (32 bytes)
17 - 255
Reserved
Reserved
Choosing the Enhanced Erase mode will simply perform the Cryptographic Erase described above, and return
status almost immediately. This is the recommended option.
To maintain consistency with the ATA Security specification, Momentus 5400 FDE drives provide an option to
perform the Normal Erase mode.
Note.
4.1.3
Choosing normal erase will result in the drive overwriting the entire drive, with data encrypted with the
newly generated encryption key, in addition to the Cryptographic Erase.
Additional technical notes
Additional notes are available on the following web site:
http://www.seagate.com/support/fde
This site shows technical notes about additional new commands for FDE drives and other FDE-related information.
28
Momentus 5400 FDE Product Manual, Rev. C
4.1.4
Drive Trust Mode supported
Identify Page - Word 150 decimal (0x96h)- Bit 12 Identifies Drive Trust Support.
Value = 1 = Drive Trust is supported (this is a trusted drive)
Table 9:
Drive Trust Identify Page
Ident Value
5
0
9
8
BIT set
Bit
Description
0
15
Vendor specific
1
14
Vendor specific
0
13
Vendor specific
1
12
Drive Trust Enabled
0
11
Vendor specific
0
10
Vendor specific
0
9
Vendor specific
0
8
Vendor specific
1
7
Vendor specific
0
6
Vendor specific
0
5
Vendor specific
1
4
Drive Trust Supported
1
3
Vendor specific
0
2
Vendor specific
0
1
Vendor specific
0
0
Vendor specific
Momentus 5400 FDE Product Manual, Rev. C
29
4.1.5
Full Disc Encryption support
Identify Page--Word 243 decimal (0xF3h)--bit 14 indicates Full Disc Encryption capability.
1 = Full Disc Encryption supported.
Table 10:
Full-disc Encryption Identify Page
Ident Value
4
0
0
0
30
BIT set
Bit
Description
0
15
Vendor specific
1
14
Full-disc Encryption
0
13
Vendor specific
0
12
Vendor specific
0
11
Vendor specific
0
10
Vendor specific
0
9
Vendor specific
0
8
Vendor specific
0
7
Vendor specific
0
6
Vendor specific
0
5
Vendor specific
0
4
Vendor specific
0
3
Vendor specific
0
2
Vendor specific
0
1
Vendor specific
0
0
Vendor specific
Momentus 5400 FDE Product Manual, Rev. C
4.1.6
Supported ATA commands
The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA
commands, refer to the Draft ATA-7 Standard.
Table 11:
Supported commands
ATA Security API
Op
Code
Command
Locked
Unlocked
Drive Trust Security API
Frozen
Secure
State
Authenticated
State
Special Commands
5C
TRUSTED RECEIVE (PIO)
Executable
Executable
Executable
Executable
Executable
5E
TRUSTED SEND (PIO)
Executable
Executable
Executable
Executable
Executable
Normal Commands
E5
CHECK POWER MODE
Executable
Executable
Executable
Executable
Executable
98
CHECK POWER MODE
Executable
Executable
Executable
Executable
Executable
51
CONFIGURE STREAM
Aborted
Executable
Executable
Aborted
Executable
B1
DEVICE CONFIGURATION
Aborted
Executable
Executable
Aborted
Executable
08
DEVICE RESET
Executable
Executable
Executable
Executable
Executable
92
DOWNLOAD MICROCODE
Aborted
Aborted
Aborted
Aborted
Aborted
90
EXECUTE DEVICE
DIAGNOSTIC
Executable
Executable
Executable
Executable
Executable
E7
FLUSH CACHE
Aborted
Executable
Executable
Aborted
Executable
EA
FLUSH CACHE EXT
Aborted
Executable
Executable
Aborted
Executable
EC
IDENTIFY DEVICE
Executable
Executable
Executable
Executable
Executable
A1
IDENTIFY PACKET
DEVICE
Executable
Executable
Executable
Executable
Executable
E3
IDLE
Executable
Executable
Executable
Executable
Executable
97
IDLE
Executable
Executable
Executable
Executable
Executable
E1
IDLE IMMEDIATE
Executable
Executable
Executable
Executable
Executable
95
IDLE IMMEDIATE
Executable
Executable
Executable
Executable
Executable
00
NOP
Executable
Executable
Executable
Executable
Executable
E4
READ BUFFER
Aborted
Executable
Executable
Aborted
Executable
C8
READ DMA
Aborted
Executable
Executable
Aborted
Executable
C9
READ DMA
Aborted
Executable
Executable
Aborted
Executable
25
READ DMA EXT
Aborted
Executable
Executable
Aborted
Executable
2F
READ LOG EXT
Aborted
Executable
Executable
Aborted
Executable
C4
READ MULTIPLE
Aborted
Executable
Executable
Aborted
Executable
Momentus 5400 FDE Product Manual, Rev. C
31
Table 11:
Supported commands
ATA Security API
Op
Code
Command
Locked
Drive Trust Security API
Unlocked
Frozen
Secure
State
Authenticated
State
29
READ MULTIPLE EXT
Aborted
Executable
Executable
Aborted
Executable
F8
READ NATIVE MAX
ADDRESS
Executable
Executable
Executable
Executable
Executable
27
READ NATIVE MAX
ADDRESS EXT
Executable
Executable
Executable
Executable
Executable
20
READ SECTOR(S)
Aborted
Executable
Executable
Aborted
Executable
21
READ SECTOR(S)
Aborted
Executable
Executable
Aborted
Executable
24
READ SECTOR(S) EXT
Aborted
Executable
Executable
Aborted
Executable
2A
READ STREAM DMA EXT
Aborted
Executable
Executable
Aborted
Executable
2B
READ STREAM EXT
Aborted
Executable
Executable
Aborted
Executable
40
READ VERIFY SECTOR(S)
Aborted
Executable
Executable
Aborted
Executable
41
READ VERIFY SECTOR(S)
Aborted
Executable
Executable
Aborted
Executable
42
READ VERIFY SECTOR(S)
EXT
Aborted
Executable
Executable
Aborted
Executable
10
RECALIBRATE
Executable
Executable
Executable
Executable
Executable
F6
SECURITY DISABLE
PASSWORD
Aborted
Executable
Aborted
Aborted
Aborted
F3
SECURITY ERASE
PREPARE
Executable
Executable
Aborted
Aborted
Aborted
F4
SECURITY ERASE UNIT
Executable
Executable
Aborted
Aborted
Aborted
F5
SECURITY FREEZE LOCK
Aborted
Executable
Executable
Aborted
Aborted
F1
SECURITY SET PASSWORD
Aborted
Executable
Aborted
Aborted
Aborted
F2
SECURITY UNLOCK
Executable
Executable
Aborted
Aborted
Aborted
70
SEEK
Executable
Executable
Executable
Executable
Executable
91
SET DRIVE PARAMETERS
Executable
Executable
Executable
Executable
Executable
EF
SET FEATURES
Executable
Executable
Executable
Executable
Executable
F9H
SET MAX ADDRESS
Aborted
Executable
Executable
Aborted
Executable
F9H / 00H
SET MAX ADDRESS EXT
Aborted
Executable
Executable
Aborted
Executable
F9H / 01H
SET MAX SET
PASSWORD
Aborted
Executable
Executable
Aborted
Executable
F9H / 02H
SET MAX LOCK
Aborted
Executable
Executable
Aborted
Executable
F9H / 04H
SET MAX FREEZE LOCK
Aborted
Executable
Executable
Aborted
Executable
32
Momentus 5400 FDE Product Manual, Rev. C
Table 11:
Supported commands
ATA Security API
Op
Code
Command
Locked
Drive Trust Security API
Unlocked
Frozen
Secure
State
Authenticated
State
F9H / 03H
SET MAX UNLOCK
Aborted
Executable
Executable
Aborted
Executable
C6
SET MULTIPLE MODE
Executable
Executable
Executable
Executable
Executable
E6
SLEEP
Executable
Executable
Executable
Executable
Executable
99
SLEEP
Executable
Executable
Executable
Executable
Executable
B0H / D9H
SMART DISABLE
OPERATIONS
Executable
Executable
Executable
Executable
Executable
B0H / D2H
SMART ENABLE/DISABLE
AUTOSAVE
Executable
Executable
Executable
Executable
Executable
B0H / D8H
SMART ENABLE
OPERATIONS
Executable
Executable
Executable
Executable
Executable
B0H / D4H
SMART EXECUTE
OFF-LINE
IMMEDIATE
Executable
Executable
Executable
Executable
Executable
B0H / 08H
SMART READ DATA
Executable
Executable
Executable
Executable
Executable
B0H / D5H
SMART READ LOG
Executable
Executable
Executable
Executable
Executable
B0H / DAH
SMART RETURN STATUS
Executable
Executable
Executable
Executable
Executable
B0H / D6H
SMART WRITE LOG
Executable
Executable
Executable
Executable
Executable
E2
STANDBY
Executable
Executable
Executable
Executable
Executable
96
STANDBY
Executable
Executable
Executable
Executable
Executable
E0
STANDBY IMMEDIATE
Executable
Executable
Executable
Executable
Executable
94
STANDBY IMMEDIATE
Executable
Executable
Executable
Executable
Executable
E8
WRITE BUFFER
Aborted
Executable
Executable
Aborted
Executable
CA
WRITE DMA
Aborted
Executable
Executable
Aborted
Executable
CB
WRITE DMA
Aborted
Executable
Executable
Aborted
Executable
35
WRITE DMA EXT
Aborted
Executable
Executable
Aborted
Executable
3D
WRITE DMA FUA EXT
Aborted
Executable
Executable
Aborted
Executable
3F
WRITE LOG EXT
Aborted
Executable
Executable
Aborted
Executable
C5
WRITE MULTIPLE
Aborted
Executable
Executable
Aborted
Executable
39
WRITE MULTIPLE EXT
Aborted
Executable
Executable
Aborted
Executable
30
WRITE SECTOR(S)
Aborted
Executable
Executable
Aborted
Executable
31
WRITE SECTOR(S)
Aborted
Executable
Executable
Aborted
Executable
34
WRITE SECTOR(S) EXT
Aborted
Executable
Executable
Aborted
Executable
Momentus 5400 FDE Product Manual, Rev. C
33
Table 11:
Supported commands
ATA Security API
Op
Code
Command
Locked
Drive Trust Security API
Unlocked
Frozen
Secure
State
Authenticated
State
3A
WRITE STREAM DMA EXT
Aborted
Executable
Executable
Aborted
Executable
3B
WRITE STREAM EXT
Aborted
Executable
Executable
Aborted
Executable
34
Momentus 5400 FDE Product Manual, Rev. C
4.1.7
Identify Device command
The Identify Device command (command code ECH) transfers information about the drive to the host following
power up. The data is organized as a single 512-byte block of data. All reserved bits or words should be set to
zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 2.0 on
page 5 for default parameter settings.
The following commands contain drive-specific features that may not be included in the Draft ATA-7 Standard.
Word
Description
Value
0
Configuration information:
• Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
0C5AH
1
Number of logical cylinders
16,383
2
ATA-reserved
0000H
3
Number of logical heads
16
4
Retired
0000H
5
Retired
0000H
6
Number of logical sectors per logical track: 63
003FH
7–9
Retired
0000H
10–19
Serial number: (20 ASCII characters, 0000H = none)
ASCII
20
Retired
0000H
21
Retired
0400H
22
Obsolete
0000H
23–26
Firmware revision
(8 ASCII character string, padded with blanks to end of string)
x.xx
27–46
Drive model number (40 ASCII characters, padded with blanks
to end of string)
ST9120826A
ST9100826A
ST980821A
ST960814A
ST940811A
47
(Bits 7–0) Maximum sectors per interrupt on Read multiple and
Write multiple (16)
8001H
48
Reserved
0000H
49
Standard Standby timer, IORDY supported and may be disabled
2F00H
50
ATA-reserved
4000H
51
PIO data-transfer cycle timing mode
0200H
52
Retired
0200H
53
Words 54–58, 64–70 and 88 are valid
0007H
54
Number of current logical cylinders
xxxxH
55
Number of current logical heads
xxxxH
56
Number of current logical sectors per logical track
xxxxH
57–58
Current capacity in sectors
xxxxH
Momentus 5400 FDE Product Manual, Rev. C
35
Word
Description
Value
59
Number of sectors transferred during a Read Multiple or Write
Multiple command
xxxxH
60–61
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
ST9120826A = 234,441,648
ST9100826A = 195,371,568
ST980821A = 156,301,488
ST960814A = 117,210,240
ST940811A = 78,140,160
62
Retired
0000H
63
Multiword DMA active and modes supported (see note following
this table)
xx00H
64
Advanced PIO modes supported (modes 3 and 4 supported)
0003H
65
Minimum multiword DMA transfer cycle time per word (120
nsec)
0078H
66
Recommended multiword DMA transfer cycle time per word
(120 nsec)
0078H
67
Minimum PIO cycle time without IORDY flow control (240 nsec)
00F0H
68
Minimum PIO cycle time with IORDY flow control (120 nsec)
0078H
69–74
ATA-reserved
0000H
75
Queue depth
0000H
76–79
ATA-reserved
0000H
80
Major version number
007EH
81
Minor version number
001BH
82
Command sets supported
346BH
83
Command sets supported
7D09H
84
Command sets support extension
4003H
85
Command sets enabled
34xxH
86
Command sets enabled
3xxxH
87
Command sets enable extension
4003H
88
Ultra DMA support and current mode
(see note following this table)
xx3FH
89
Security erase time
0000H
90
Enhanced security erase time
0000H
91
Advanced power management value
8080H
92
Master password revision code
FFFEH
93
Hardware reset value (see description following this table)
xxxxH
94
Auto acoustic management setting
xxxxH
95–127
ATA-reserved
0000H
128
Security status
0001H
129–149
Seagate-reserved
xxxxH
36
Momentus 5400 FDE Product Manual, Rev. C
Word
Description
Value
150
Drive Trust Identify
5098H
151–159
Seagate-reserved
xxxxH
160–242
ATA-reserved
0000H
243
Disk Encryption Supported
4000H
244–254
ATA-reserved
0000H
255
Integrity word
xxA5H
Note.
See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data.
Description (if bit is set to 1)
Bit
Word 63
Bit
Word 88
0
Ultra DMA mode 0 is supported.
1
Ultra DMA mode 1 is supported.
2
Ultra DMA mode 2 is supported.
3
Ultra DMA mode 3 is supported.
4
Ultra DMA mode 4 is supported.
8
Ultra DMA mode 0 is currently active.
9
Ultra DMA mode 1 is currently active.
10
Ultra DMA mode 2 is currently active.
11
Ultra DMA mode 3 is currently active.
12
Ultra DMA mode 4 is currently active.
13
Ultra DMA mode 5 is currently active.
Bit
Word 93
13
1 = 80-conductor cable detected, CBLID above VIH
0 = 40-conductor cable detected, CBLID below VIL
Momentus 5400 FDE Product Manual, Rev. C
37
4.1.8
Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the
Features register are defined as follows:
Table 12:
Features register values
02H
Enable write cache (default).
03H
Set transfer mode (based on value in Sector Count register).
Sector Count register values:
00H
Set PIO mode to default (PIO mode 2).
01H
Set PIO mode to default and disable IORDY (PIO mode 2).
08H
PIO mode 0
09H
PIO mode 1
0AH
PIO mode 2
0BH
PIO mode 3
0CH
PIO mode 4 (default)
20H
Abort, note supported
21H
Abort, note supported
22H
Abort, note supported
40H
Ultra DMA mode 0
41H
Ultra DMA mode 1
42H
Ultra DMA mode 2
43H
Ultra DMA mode 3
44H
Ultra DMA mode 4
45H
Ultra DMA mode 5
05H
Enable advanced power management
55H
Disable read look-ahead (read cache) feature.
82H
Disable write cache.
AAH
Enable read look-ahead (read cache) feature (default).
F1H
Report full capacity available
Note.
38
At power-on or after a hardware or software reset the default values of the features are as indicated
above.
Momentus 5400 FDE Product Manual, Rev. C
5.0
Compatibility summary
5.1
Installation considerations
Many of today’s mobile computers have been designed to make it possible for the end user to replace the hard
drive. Refer to your system’s user manual for the location of the hard drive compartment and the specific
instructions regarding replacement. Refer to your system manufacturer’s support website for the most up-todate information. Read and follow all instructions regarding the proper steps to be taken when replacing the
system hard drive. Some mobile systems are sealed and require specialized tools to gain access to the hard
drive. Special training or tools may be needed to service some mobile computers. In some cases, opening the
case may void your warranty. Consult your system documentation. Seagate recommends taking your system
to an authorized service technician to replace your hard drive.
Momentus 5400 FDE Product Manual, Rev. C
39
System Compatibility
Seagate Product Assurance has tested Momentus drives in the systems listed in Table 13. Testing included
multiple BIOS versions and operating systems. This testing was done to demonstrate compatibility with various
hardware and software configurations. Hardware and software combinations, other than those tested, may
also be compatible with this drive.
Table 13:
Tested systems
Acer Aspire 2000
Client Pro 345E
Compaq NX9500
Compaq D315
Compaq E -6000
Dimension GX400
Dimension 4100
Dimension 4100 XPSZ
Dimension 4400
Dimension 4500S
Dimension 4600
Dimension 8100
Dimension 8200
Dimension 8250
Dimension 8300
Dimension XPS
Gigabyte GA-8SIML
Gigabyte GA-8SR533
HP/Compaq NX7000
HP D330
HP D330 MT
HP D330 UT
HP D530
HP D530 CMT
HP D530 SFF
HP D530 USDT
5.2
IBM R50
IBM R50P
IBM XNote
Imedia 7150(Discovery)
Inspiron 8100
Inspiron 1150
Inspiron 2650
Inspiron 300M
Inspiron 5100
Inspiron 5150
Inspiron 600M
Inspiron 8600
Inspiron 9100
Inspiron XPS
Intel 845GBV
Intel SPRINGDALE-G
JIA HE H150
Latitude 100L
Latitude 8600
Latitude D400
Latitude D505
Latitude D600
Latitude D800
Latitude X300
Lavie LJ700/7E
Micron T2100
Micron T2200
Microstar MSI-6561
Microstar MSI-6566E
Netvista
Optiplex GX150
Optiplex GX260
Optiplex GX400
Pavilion 774Y
Pavilion ZD7000
Pavilion ZT3000
Pavilion ZV5000
Pavilion ZX5000
Performance
Performance 1400
Performance 1500
Sony PCV-RZ60
Vaio PCG-V505/B
Vaio PCG-ZIR/P
Vaio PCV RX770
Vaio PCV7753
Vaio PCV-7753
BIOS versions tested
The following list indicates the types of BIOS Seagate tested during the compatibility testing process. The list
highlights the major BIOS manufacturers. Individual systems contain variations of these BIOS versions and
were tested with regard to their implementation in the individual systems.
Table 14:
Vendor
Tested BIOS versions
Release
ACER
Revision
1.01
Award
Various
Various
Compaq
68xxx
Various
Compaq
78xxx
Various
Compaq
8602
v1.08
Compaq
F.07
Dell
Various
A03
HP
Various
Various
IBM
Various
Various
40
Momentus 5400 FDE Product Manual, Rev. C
Table 14:
Tested BIOS versions
Vendor
Release
Revision
Intel
786B2
v1.11
NEC
Various
Various
Phoenix
Various
Various
5.3
Operating system versions tested
This list indicates the types of Operating Systems Seagate tested during the compatibility testing process and
highlights the major OS manufacturers. Several variations of the major operating systems have been tested.
Table 15:
Operating systems tested
Manufacturer
Version/Release
Microsoft
Windows Server 2003 (Compatibility evaluated, but not tested)
Microsoft
Windows XP, XP Pro, XP Home (Service Pack 2) (multiple languages)
5.4
Compatibility test configurations
The Momentus drives have been tested to demonstrate compliance in both the master drive and slave drive
positions, including master and slave selection via the cable select feature. These tests are performed to
ensure functionality to the ATA/ATAPI-7 specification. Seagate design and testing are constantly evolving to
match the evolution of the ATA/ATAPI specifications. Momentus drives should be expected to be largely compliant to the emerging ATA/ATAPI-8 specification.
Notes exceptions to the specifications for the Momentus 5400 FDE are listed in the ATA Interface Section
above.
5.5
Software utilities
The following is a brief overview of a some of the Seagate utilities used during the Seagate competitive analysis process.
The Seagate SeaTools application is an exclusive disc drive diagnostic software designed to troubleshoot most
hard drive issues. Desktop edition works with most ATA, SATA, or SCSI drives in desktop systems and has a
98 percent accuracy rate.
The Seagate DiscWizard™ application simplifies the installation of disc drives. This software also overcomes
many system BIOS and operating system limitations that can complicate the installation of higher-capacity ATA
(IDE) interface drives.
This is a list of some of the third party utilities used in the testing process.
Vendor
Application
Intel
PCI-EXE
Microsoft
Winbench99
Symantec
Norton Utilities
Momentus 5400 FDE Product Manual, Rev. C
41
5.5.1
Third party software support
Seagate does not supply password management software. Third party software support for security features is
available. For the latest list of available software, please refer to the following web site:
http://www.seagate.com/support/fde
42
Momentus 5400 FDE Product Manual, Rev. C
6.0
Seagate Technology support services
Internet
For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is
available 24 hours daily by email for your questions.
Presales Support:
Presales@Seagate.com
Technical Support:
DiscSupport@Seagate.com
Warranty Support:
http://www.seagate.com/support/service/index.html
mySeagate
my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides
self-service access to critical applications, personalized content and the tools that allow our partners to
manage their Seagate account functions. Submit pricing requests, orders and returns through a single,
password-protected Web interface-anytime, anywhere in the world.
spp.seagate.com
spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You
may register for customized communications that are not available on the web. These communications contain
product launch, EOL, pricing, promotions and other channel-related information. To learn more about the
benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.
Seagate Service Centers
Presales Support
Our Presales Support staff can help you determine which Seagate products are best suited for your specific
application or computer system, as well as product availability and compatibility.
Technical Support
Seagate technical support is available to assist you online at support.seagate.com or through one of our call
centers. Have your system configuration information and your “ST” model number available.
SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or
comments 24 hours daily and exchange messages with a technical support specialist during normal business
hours for the call center in your region.
Momentus 5400 FDE Product Manual, Rev. C
43
Customer Service Operations
Warranty Service
Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct
customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate
warranty service for assistance. Have your serial number and model or part number available.
Data Recovery Services
Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery
services labs are currently located throughout the world. . Additional information, including an online request
form and data loss prevention resources, is available at http://services.seagate.com/index.aspx
Authorized Service Centers
Seagate Service Centers are available on a global basis for the return of defective products. Contact your
customer support representative for the location nearest you.
USA/Canada/Latin America support services
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/
Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.
Global Customer Support
Presales, Technical, and Warranty Support
Call Center
Toll-free
USA, Canada,
and Mexico
1-800-SEAGATE
Data Recovery Services
Call Center
USA, Canada,
and Mexico
Toll-free
1-800-475-01435
Direct dial
+1-405-324-4700
Direct dial
+1-905-474-2162
FAX
1-800-475-0158
+1-905-474-2459
Europe, the Middle East and Africa Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the
Middle East and Africa, go to the "Contact Us" page on www.seagate.com.
Asia/Pacific Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,
go to the "Contact Us" page on www.seagate.com.
44
Momentus 5400 FDE Product Manual, Rev. C
Index
Numerics
3D Defense System 1
A
acoustics 14
Active mode 12
AFR 16
agency certification (regulatory) 16
altitude 13
ambient conditions 5
ambient temperature 9, 13
Annualized Failure Rate 16
areal density 8
ATA interface 25
ATA-standard commands 31
Australian C-Tick 17
autodetection 1
average seek time 9
B
BIOS manufacturers 40
BPI 8
buffer 1, 8
burst 1
C
cable select 1
cable-select option 20
cache 1, 8
case temperature 13
CE mark 16
certification 16
chemical substances 18
commands 31
compatibility 40
compatibility summary 39
compatibility test configurations 41
compliance 16
conducted noise 11
conducted RF immunity 15
configuring the drive 19
connector pins 25
Corrosive environment 18
CSA C22.2 (950) 16
CSEL 20
C-Tick 17
current profile 11
cycles 16
Momentus 5400 FDE Product Manual, Rev. C
D
Data Defense 1
data-transfer rates 1
DC power 10
demonstrate compliance 41
density 8
Diagnostic Defense 1
diagnostic software 1
discs 7
dissipation 10
Drive Defense 1
drive diagnostics 9
drive monitoring 1
drive self-test 1
E
electrical fast transient 15
electromagnetic compatibility 16
Electromagnetic Compatibility Directive 16
electromagnetic immunity 15
electrostatic discharge 15
EMC compliance 16
EN 60950 16
enclosures 17
Environmental protection 18
environmental specifications 13
error-correction algorithms 1
errors 16
European Union 16
European Union Restriction of Hazardous Substances 18
F
FCC verification 17
Features register 38
formatted capacity 7
frequency 15
G
guaranteed sectors 7
H
handling 19
heads 1, 7
height 8
humidity 13
I
I/O data-transfer rate 8
Identify Device command 35
Idle 10
Idle and Standby timers 12
45
Idle mode 12
Idle mode power 10
IEC950 16
Information Technology Equipment 16
interface 8, 25
interface signals 25
interference 17
interleave 8
internal data-transfer rate OD 8
ISO document 7779 14
power frequency h-field immunity 15
power management 12
power on/off cycles 16
power specifications 10
power-management modes 12
Power-on to Ready 9
precautions 20
programmable power management 12
J
radiated RF immunity 15
radio and television interference 17
radio frequency (RF) 15
random track location 10
read errors 16
Read Multiple 1
read/write heads 7
read/write power and current 10
recording and interface technology 8
recording density 8
recording heads 1
recording method 8
register 38
relative humidity 13
reliability 16
resistance 11
RF 15
RoHS 18
jumper settings 20
K
Korean RRL 17
L
LBA mode 7
length 8
Load/Unload 16
logical geometry 7
M
master/slave 1
Master/slave configuration 20
maximum temperature 13
modes 25
monitoring 1
mounting the drive 19, 20
N
nIEN bit 26
noise 11
nominal power 5
nonoperating shock 14
nonoperating vibration 14
nonrecoverable read errors 16
O
operating shock 13
operating system 40
operating vibration 14
OS manufacturers 41
P
physical characteristics 8
physical organization 7
pins 25
PIO 25
power consumption 10
power dissipation 10
46
R
S
S.M.A.R.T. drive monitoring 1
safety certification 16
screws 20
SeaTools 1
sectors 7
seek mode 10
seek time 9
Seeking 10
Self refresh, low power 12
servo electronics 10
Set Features command 38
shock 13
signals 25
single-track seeks 9
Sleep 10
Sleep mode 12
software utilities 41
sound 14
specifications 5
spindle speed 8
Spinup 10
spinup power 10
Standby 10
Standby mode 10, 12
Momentus 5400 FDE Product Manual, Rev. C
Standby to Ready 9
static-discharge precautions 19
subassembly 17
support services 43
surge immunity 15
T
technical support services 43
temperature 13
temperature gradient 13
third party utilities 41
time to ready 9
timers 12
TMR 1
track density 8
track-to-track seek time 9
TUV North America 16
U
UL 1950 16
V
vibration 14
voltage 11
voltage dips, interrupts 15
voltage tolerance 11
W
Warranty 16
weight 8
wet bulb temperature 13
width 8
Write Multiple 1
Momentus 5400 FDE Product Manual, Rev. C
47
48
Momentus 5400 FDE Product Manual, Rev. C
Seagate Technology LLC
920 Disc Drive, Scotts Valley, California 95066-4544, USA
Publication Number: 100377037, Rev. C, Printed in U.S.A.