www.senabluetooth.com
User's Guide
SMH10
Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH5™, SMH5-FM™, SPH10™,
SPH10H™, SPH10H-FM™, SMH10R™, SPH10S™, SPH10H™, SR10™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries.
These trademarks may not be used without the express permission of Sena.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. iPhone, iPod
touch are the registered trademark of Apple Inc. Zumo™ is a trademark of Garmin Ltd. or its subsidiaries. TomTom™ is the trademark or
registered trademark owned by TomTom International B.V. Other trademarks and tradenames are those of their respective owners.
English
© 1998-2013 Sena Technologies, Inc. All rights reserved.
Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice.
SMH10
CONTENTS
1.INTRODUCTION......................................................................................................................... 3
2. PACKAGE CONTENTS.............................................................................................................. 4
3. INSTALLING THE SMH10 ON YOUR HELMET......................................................................... 5
4. POWERING ON/OFF AND CHARGING..................................................................................... 8
4.1 Powering On...................................................................................................................... 8
4.2 Powering Off....................................................................................................................... 8
4.3Charging............................................................................................................................ 8
4.4 Low Battery Warning.......................................................................................................... 8
4.5 Checking the Battery Level................................................................................................ 8
5. VOLUME ADJUSTMENT............................................................................................................ 9
6. PAIRING THE SMH10 WITH BLUETOOTH DEVICES.............................................................. 9
6.1 Mobile Phone Pairing......................................................................................................... 9
6.2 Multipoint Pairing............................................................................................................. 10
6.3 Bluetooth Stereo Device Pairing...................................................................................... 10
6.4 Bluetooth GPS Navigation Pairing................................................................................... 11
6.5Pairing with the Sena SR10, Bluetooth Two-way Radio Adapter.................................... 13
7. PAIRING WITH SELECTIVE PROFILE: A2DP STEREO OR HANDSFREE........................... 14
7.1 A2DP Stereo Music Only.................................................................................................. 14
7.2 HFP for Phone Call Only.................................................................................................. 15
8. INTERCOM PAIRING............................................................................................................... 15
8.1 Pairing with Other SMH10 Headsets for Intercom Conversation..................................... 15
8.2 Pairing with Other Sena Headset Models for Intercom Conversation.............................. 16
9. SMH10 CONFIGURATION SETTING...................................................................................... 17
9.1 Enabling/Disabling Voice Activated Phone Answering ................................................... 17
9.2 Enabling/Disabling Voice Activated Intercom ................................................................. 18
9.3 Enabling/Disabling Voice Prompts................................................................................... 18
9.4 Delete all Bluetooth Pairing Information .......................................................................... 18
9.5 Exit Voice Configuration Menu ........................................................................................ 19
10.FUNCTION PRIORITY.............................................................................................................. 19
11.STEREO MUSIC....................................................................................................................... 20
11.1 By Stereo Audio Cable..................................................................................................... 20
11.2 By Bluetooth Wireless Stereo .......................................................................................... 20
12.MOBILE PHONE CALL MAKING AND ANSWERING.............................................................. 21
13.TWO-WAY INTERCOM............................................................................................................ 22
13.1 Start and End Two-way Intercom..................................................................................... 22
13.2 Intercom and Mobile Phone Call...................................................................................... 23
13.3 Intercom and GPS ........................................................................................................... 23
13.4 Intercom and Two-way Radio........................................................................................... 24
14.THREE-WAY CONFERENCE INTERCOM.............................................................................. 25
14.1 Start Three-way Intercom................................................................................................. 25
14.2 End Three-way Intercom................................................................................................... 26
15.FOUR-WAY CONFERENCE INTERCOM................................................................................ 27
15.1 Start Four-way Intercom................................................................................................... 27
15.2 End Four-way Intercom.................................................................................................... 27
16.THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT................... 28
17.INTERCOM FAILURE............................................................................................................... 28
18.INTERCOM RECONNECTION................................................................................................. 28
19.RESET TO FACTORY DEFAULT SETTINGS.......................................................................... 29
20.FAULT RESET.......................................................................................................................... 29
21.FIRMWARE UPGRADE............................................................................................................ 29
22.CASE STUDY........................................................................................................................... 30
BATTERY INFORMATION............................................................................................................. 33
MAINTENANCE AND CARE.......................................................................................................... 33
DISPOSAL...................................................................................................................................... 34
CERTIFICATION AND SAFETY APPROVALS.............................................................................. 34
• FCC RF Exposure Statement................................................................................................. 35
• FCC Caution.......................................................................................................................... 35
• CE Declaration of Conformity................................................................................................ 35
• Industry Canada Statement................................................................................................... 35
• Bluetooth License.................................................................................................................. 35
WAIVER AND GENERAL RELEASE............................................................................................. 36
• Two-Year Limited Warranty.................................................................................................... 37
• Limitation of Liability.............................................................................................................. 38
• Return for Full Refund............................................................................................................ 38
WARNING...................................................................................................................................... 39
SMH10
Thank you for choosing the Sena SMH10, Bluetooth Stereo Headset
and Intercom for Motorcycles. With the SMH10, you can call
handsfree on your Bluetooth mobile phone, listen to stereo music or
voice instructions of GPS navigations by Bluetooth wirelessly, and
have intercom conversations in full duplex with a passenger or other
motorcycle riders.
The SMH10 is compliant with the Bluetooth 3.0 supporting the following
profiles: Headset Profile, Hands-Free Profile (HFP), Advanced Audio
Distribution Profile (A2DP), and Audio Video Remote Control Profile
(AVRCP). Please check with the manufacturers of other devices to
determine their compatibility with this headset.
Please read this user’s guide carefully before using the headset. Also
check www.senabluetooth.com/support for the latest version of
the user’s guide and additional information related to Sena Bluetooth
products.
The SMH10 features:
•Bluetooth handsfree for Bluetooth mobile phones
•Bluetooth stereo headset for Bluetooth audio devices such as MP3
players
•Bluetooth stereo headset for Bluetooth GPS navigations
•Bluetooth intercom up to 900 meters (980 yards)*
•Four-way conference intercom
•Three-way conference phone call with intercom participant
•Multipoint Bluetooth pairing with GPS navigation or Sena SR10
two-way radio adapter
•Multipoint Bluetooth pairing for 2 mobile phones
•Stereo music by 3.5mm audio cable
•Firmware upgradeable
English
1.INTRODUCTION
Key Specifications:
•Bluetooth 3.0
•
Supporting profiles: Headset Profile, Hands-Free Profile (HFP),
Advanced Audio Distribution Profile (A2DP), Audio Video Remote
Control Profile (AVRCP)
* in open terrain
3
SMH10
2.PACKAGE CONTENTS
• Clamp Unit
- Speaker-Microphone Clamp Unit - Basic Kit
• Headset Main Unit
DC Power Charging & Firmware Upgrade Port
Speakers
Phone Button
• Answer and end a mobile phone call
• Redial last number
Microphone
MP3 Jack
• Call transfer between mobile phone and headset
• Enter into mobile phone pairing mode
• Enter into Bluetooth stereo device paring mode
• Enter into factory reset mode
Jog Dial
• Answer and end a mobile phone call
• Reject an incoming mobile phone call
• Start and end intercom conversation
• Volume adjustment by rotating
• Play and pause Bluetooth stereo device
• Track-forward and track-back by rotating while pressing the
button
• Enter into intercom pairing mode
• Enter into voice configuration setting
• Navigate through configuration menu
4
- Speaker-Microphone Clamp Unit with Universal Microphone Kit
• Clamp and Speakers
• Boom Microphone
• Wired Microphone
SMH10
• Cigarette Charger
• 3.5mm Stereo Audio Jack Cable
• Glued Surface Mounting Adapter
• Microphone Sponges
• Speaker Pads
3.INSTALLING THE SMH10 ON YOUR HELMET
English
• USB Power & Data Cable
To securely install the SMH10 on the helmet, please follow the
procedure.
1.Loosen the two screws on the back plate of the speakermicrophone clamp unit using the enclosed Allen Wrench. Insert
the back plate of the clamp unit between the internal padding and
external shell of the helmet, and tighten the two screws. Please
make sure that the microphone is located properly close to your
mouth when you wear the helmet.
Insert
• Velcro Pads for Speakers
• Allen Wrench
5
SMH10
2.Please adjust the direction of the microphone so that the fin side
of the microphone is facing outward; away from your lips. You can
easily recognize it by touching the fin with your fingers.
fin
When installing the boom microphone included in the “Universal
Microphone Kit”, place the velcro end of the boom microphone
between the internal helmet cheek pad and the internal wall of the
helmet shell. The boom microphone should be mounted so it is
facing close to your mouth when you wear the helmet. You can use
the enclosed velcro pad and holder for the boom microphone to
ensure secure placement.
6
In the case of the wired microphone also included in the “Universal
Microphone Kit”, attach the enclosed velcro pad for wired
microphone to the inside of the chin guard for full-face helmets.
Place the wired microphone on the velcro pad and connect it to the
connector of the clamp unit.
3.Place the helmet speakers along with the velcro pads, centered to
your ear, in the ear pockets of the helmet. If the helmet has deep
ear pockets, you can use the speaker pads to place the speakers
closer to your ears.
SMH10
Attach
any responsibility for use of it. Users may have to use the glued
adapter at their own risk and responsibility.
5.Attach the headset main unit to the speaker-microphone clamp
unit. Insert the bottom part of the main unit completely into the
lower slot of the clamp unit first. Then push the upper part of the
main unit until it clicks into the upper holder of the clamp unit.
English
4.If you have any problem to clamp the speaker-microphone unit
on the helmet for any reason, you may use the glued surface
mounting adapter to attach the speaker-microphone clamp unit
on the external surface of the helmet.
•Remove the back plate of the speaker-microphone clamp unit by
loosening the two screws with the enclosed Allen Wrench.
•Attach the glued external adapter to the speaker-microphone
clamp unit by tightening the two screws instead of the removed
back plate.
•Locate a proper surface on the helmet to attach the unit, clean
the helmet surface location with a moistened towel, and allow to
dry thoroughly.
•Peel off the cover of the adhesive tape of the adapter and attach
the unit on the proper surface of your helmet.
6.To remove the main headset from the speaker-microphone clamp
unit, hold the lower part of the speaker-microphone clamp unit
with your thumb and gently press down the hook on the upper part
of the headset main unit with your index finger until it clicks out.
You may have to do this to charge up or to carry the headset main
unit.
Sena recommends the clamp unit over the glued surface
mounting adapter. Even though the glued surface mounting
adapter is provided for convenience, Sena does not assume
7
SMH10
4.POWERING ON/OFF AND CHARGING
To power on and off the headset, you don’t need to press and hold
any button for several seconds. Just short press the Jog Dial and
the Phone Button simultaneously, and you will get quick on-and-off
convenience.
4.1 Powering On
Press the Jog Dial and the Phone Button at the same time for about
1 second to power on. The blue LED turns on and you will hear
ascending beeps.
4.2 Powering Off
Just short press the Jog Dial and the Phone Button simultaneously,
you don’t need to press and hold for a few seconds. The red LED
turns on for a while until it turns off completely and you will hear
descending beeps.
4.3Charging
The LED turns on red while charging, and turns to blue when the
headset is fully charged. It takes about 2.5 hours to be completely
charged.
8
4.4 Low Battery Warning
When the battery is low, the blinking blue LED in stand-by mode turns
to red and you will hear mid-tone triple beeps and a voice prompt
saying “Low battery”.
4.5 Checking the Battery Level
You can check the battery level in two different ways when the
headset is powering on.
4.5.1 LED Indicator
When the headset is powering on, the red LED flashes rapidly
indicating the battery level.
4 flashes = High, 70~100%
3 flashes = Medium, 30~70%
2 flashes = Low, 0~30%
4.5.2 Voice Prompt Indicator
When you power on the headset, keep pressing the Jog Dial and
Phone Button simultaneously for about 3 seconds until you hear
high tone triple beeps. Then you will hear voice prompt indicating
the battery level. However, if you release the buttons as soon as the
headset turns on, you will not hear the voice prompt of battery level
indication.
SMH10
You can easily adjust the volume by rotating the Jog Dial. You will
hear a beep when the volume reaches maximum or minimum level.
The volume is set and maintained independently at different levels
for each audio source even when you turn off and on the headset.
For example, once you set the volume for mobile phone handsfree,
it will not change even if you adjust the volume when you hear
Bluetooth MP3 music. So you can always maintain the preferred
optimum volume level for each audio source.
6. PAIRING THE SMH10 WITH BLUETOOTH DEVICES
English
5.VOLUME ADJUSTMENT
Before using the SMH10 Bluetooth headset with any of Bluetooth
devices for the first time, you need to do the pairing operation. It can
be paired with Bluetooth mobile phones, Bluetooth stereo devices
such as MP3, or motorcycle specific Bluetooth GPS, and with other
Sena Bluetooth headsets. This pairing operation is only required
once for each Bluetooth device. The headset will remain paired with
the devices and automatically connects to the paired devices again
when they are within range. You will hear a high tone single beep
and a voice prompt when the headset connects to the paired device
automatically: “Phone connected” to a mobile phone, “Media
connected” to a Bluetooth stereo device.
6.1 Mobile Phone Pairing
1. Turn on the SMH10 and press the Phone Button for 5 seconds until
the LED flashes red and blue alternately and you hear multiple
beeps. You will hear a voice prompt saying “Phone pairing”.
2.Search for Bluetooth devices on your mobile phone. Select the
Sena SMH10 in the list of the devices detected on the mobile
phone.
9
SMH10
3.Enter 0000 for the PIN. Some mobile phones may not ask for
PIN.
4.The mobile phone confirms that pairing has completed and
SMH10 is ready to use. You will hear a voice prompt from
SMH10 saying “Your headset is paired”.
5.If the pairing process is not completed within three minutes,
SMH10 will return to stand-by mode.
the
the
the
the
6.2 Multipoint Pairing
Typical Bluetooth headsets can connect with only one HFP (HandsFree Profile) device, but multipoint pairing allows the headset to
connect with two HFP devices at the same time. So, when you already
have a mobile phone connected with the SMH10, you can also pair
and connect a second mobile phone or other HFP devices such as
GPS or Sena SR10, Bluetooth adapter.
1.To pair the second mobile phone, press the Jog Dial for 5 seconds
again until the red LED is rapidly flashing and you hear multiple
beeps.
2.Within 2 seconds, tap the Phone Button again, then the LED turns
to blue flashing and the beeps turn to high tone double beeps. You
will hear a voice prompt saying “Multipoint pairing”.
3.Search for Bluetooth devices on your mobile phone. Select the
Sena SMH10 in the list of the devices detected on the mobile
phone.
10
4.Enter 0000 for the PIN. Some mobile phones may not ask for the
PIN.
5.The mobile phone confirms that pairing has completed and the
SMH10 is ready to use. You will hear a voice prompt from the
SMH10 saying “Your headset is paired”.
6.If you want to pair a GPS by multipoint pairing, search for the
Bluetooth device on the GPS screen, and select the Sena SMH10
at step 3. Please refer to the section “6.4.1 Multipoint GPS Pairing”
for more details.
7.If you want to pair the Sena SR10, Bluetooth adapter, please refer
to the section “6.5 Pairing with the Sena SR10, Bluetooth Two-way
Radio Adapter”.
6.3 Bluetooth Stereo Device Pairing
1.If the Bluetooth stereo device is integrated with the mobile phone
such as smartphones, you don’t need to pair the SMH10 with it
separately. When the SMH10 is paired with the mobile phone, it is
also paired as a stereo music device.
2. If you have a stand alone Bluetooth stereo device, follow the paring
procedure separately. The procedure is the same as the procedure
in “6.1 Mobile Phone Pairing”.
SMH10
1. If
Bluetooth connection between the headset and a mobile phone
is disconnected, tap the Phone Button to recover the Bluetooth
connection immediately.
2. If Bluetooth connection between the headset and a media player is
disconnected, press the Jog Dial for 1 second to recover the Bluetooth
connection and play.
6.4 Bluetooth GPS Navigation Pairing
You can listen to voice instruction from Bluetooth GPS navigation.
Some GPS systems use mobile phone profile (HFP, Hands-Free
Profile) and others use stereo music profile (A2DP, Advanced
Audio Distribution Profile). Most motorcycle specific GPS systems
use mobile phone profile for turn-by-turn voice instruction. You can
simultaneously use a mobile phone and a GPS which uses mobile
phone profile by one of the following procedures.
1.Turn on the headset and press the Jog Dial for 5 seconds until the
red LED is rapidly flashing and you hear multiple beeps.
2.Within 2 seconds, tap the Phone Button again, then the LED turns
to blue flashing and the beeps turn to high tone double beeps.
You will hear a voice prompt saying “Multipoint pairing”.
3.Search for Bluetooth devices on the GPS navigation screen.
Select the Sena SMH10 in the list of the devices detected on the
GPS.
4.Enter 0000 for the PIN.
5.The GPS confirms that pairing has completed and the SMH10 is
ready to use. You will hear a voice prompt from the SMH10 saying
“Your headset is paired”.
6.If the pairing process is not completed within three minutes, the
SMH10 will return to stand-by mode.
English
Note:
6.4.1 Multipoint GPS Pairing
If you use GPS only for turn-by-turn voice instructions, not for Bluetooth
stereo music streaming, multipoint pairing is recommended for the
GPS connection. Multipoint Bluetooth pairing allows the SMH10
to connect two HFP devices at the same time: mobile phone and
GPS navigation. Follow the steps below to pair the GPS using the
multipoint pairing.
11
SMH10
The pairing diagram for multipoint GPS pairing is shown in the figure
below.
phone bridging over Bluetooth, you can pair the mobile phone to the
GPS to use your mobile phone. Please refer to the user’s guide of your
GPS for details.
HFP
Smart Phone
GPS
HFP
+ Mobile Phone
Pairing
A2DP
Mobile Phone
HFP
+ Mobile Phone
Pairing
(A2DP)
HFP
SMH10
Multipoint
Pairing
GPS
SMH10
GPS Pairing as Mobile Phone
Multipoint GPS Pairing
6.4.2 GPS Pairing as Mobile Phone
If GPS is not only used for turn-by-turn voice instructions but also
is your preferred Bluetooth stereo music source, you can pair the
GPS to the SMH10 by following the simple procedures in “6.1 Mobile
Phone Pairing”. When you do this, the SMH10 thinks the GPS is a
mobile phone so you can no longer pair your mobile phone to the
SMH10 directly. However, since some GPS systems support mobile
12
Note:
You have to use a motorcycle specific GPS which transmits turn-byturn voice instruction to the headset by Bluetooth. Most automotive GPS
systems don’t have this feature.
SMH10
The Sena SR10 is a Bluetooth two-way radio adapter for group
communication, and uses HFP as do most motorcycle specific GPS
navigation systems. If you pair the SMH10 with a SR10 by multipoint
pairing, the SMH10 is able to have two HFP devices at the same
time: mobile phone and Sena SR10.
1.Turn on the headset and press the Jog Dial for 5 seconds until the
red LED is rapidly flashing and you hear multiple beeps.
2.Within 2 seconds, tap the Phone Button again, then the LED turns
to blue flashing and the beeps turn to high tone double beeps.
You will hear a voice prompt saying “Multipoint pairing”.
3.Turn on the SR10 and follow the SR10’s “Bluetooth Headset
Pairing” procedure to complete the process. Please refer to the
SR10 user's guide for details.
4.When the pairing is completed, you will hear a voice prompt
saying “Your headset is paired”.
5.If the pairing process is not completed within three minutes, the
SMH10 will return to stand-by mode.
The incoming audio from the two-way radio via SR10 is heard in
the background while having an intercom conversation or a mobile
phone call. You can listen to music, answer a mobile call, have an
intercom conversation and use a two-way radio via SR10 for group
communication as shown in the figure below. A GPS navigation or
a radar detector could be connected to the SR10 by wire. The GPS
voice instruction or the radar detector alarm is also heard in the
background via SR10 while having an intercom conversation or a
phone call. Please refer to the SR10 user's guide for details.
English
6.5Pairing with the Sena SR10, Bluetooth Two-way
Radio Adapter
13
SMH10
7.PAIRING WITH SELECTIVE PROFILE:
A2DP STEREO OR HANDSFREE
Smart Phone
HFP
+ Mobile Phone
Pairing
A2DP
Wired
Connection
HFP
SMH10
If you have a MP3 stereo music phone such as a smartphone,
sometimes you may need to selectively use the SMH10 for
A2DP stereo music only or for mobile phone handsfree only. This
instruction is for advanced users who want to pair the SMH10 to their
smartphones only with one selective profile: A2DP stereo for music or
HFP for phone call.
Two-way radio
Multipoint
Pairing
Wired
Connection
Sena SR10
GPS
Wired
Connection
Radar Detector
Parallel Connection of SR10 and Mobile Phone by
Bluetooth Multipoint Pairing
14
If you have previously paired a mobile phone to the SMH10, you
must clear the previous paring list on both devices; the mobile phone
and SMH10. To clear the pairing list on SMH10, please do a factory
reset or follow the pairing list clearing procedure described in this
manual. To clear the pairing list on the mobile phone, please refer to
the mobile phone manual. For most smartphones, delete the Sena
SMH10 from the list of Bluetooth devices in setting menu.
7.1 A2DP Stereo Music Only
1.Turn on the headset and press the Phone Button for 5 seconds
until the LED flashes red and blue alternately and you hear multiple
beeps.
SMH10
7.2 HFP for Phone Call Only
1.Turn on the headset and press the Phone Button for 5 seconds
until the LED flashes red and blue alternately and you hear
multiple beeps.
2.Within 2 seconds, tap the Phone Button again, then the LED turns
to blue flashing and the beeps turn to multiple mid-tone beeps.
You will hear a voice prompt saying “Phone selective pairing”.
3.Search for Bluetooth devices on your smartphone. Select the
Sena SMH10 in the list of devices detected on your phone.
4.Enter 0000 for the PIN. Some smart phones may not ask for PIN.
8.INTERCOM PAIRING
English
2.Within 2 seconds, tap the Jog Dial again, then the LED turns to
red flashing and the beeps turn to double mid-tone beeps. You
will hear a voice prompt saying “Media selective pairing”.
3.Search for Bluetooth devices on your smartphone. Select the
Sena SMH10 in the list of devices detected on your phone.
4.Enter 0000 for the PIN. Some smartphones may not ask for PIN.
8.1 Pairing with Other SMH10 Headsets for Intercom
Conversation
The SMH10 can be paired with up to three other headsets for
Bluetooth intercom conversation.
1.Turn on the two SMH10 headsets (A and B) that you would like to
pair with each other.
2.Press and hold the Jog Dial of the headset A and B for 5 seconds
until red LEDs of the both units start to flash rapidly. You will hear
a voice prompt saying “Intercom pairing”.
3.Simply tap the Jog Dial of any one of the two headsets A or B
(It doesn’t matter that you choose A or B.) and wait until the
LEDs of both headsets turn to blue and intercom connection is
automatically established. The two SMH10 headsets A and B are
paired with each other for intercom conversation. If the pairing
process is not completed within one minute, the SMH10 will return
to stand-by mode.
15
SMH10
5.The intercom pairing queue is ‘Last-Come, First-Served’. If a
headset has multiple paired headsets for intercom conversations,
the last paired headset is set as first intercom friend. The
previous intercom friend becomes second intercom friend, and
third intercom friend.
A
D
B
Note:
C
For example, after the pairing procedures listed above, headset D is the
first intercom friend of headset A. Headset C is the second intercom
friend of headset A, and headset B is the third intercom friend of headset
Pairing A & B
A.
4.You can make other pairings between the headset A and C, and
between the headset A and D by following the same procedure as
above.
A
C
Pairing A & C
16
The SMH10 can be paired with all other Sena headset models such
as the SMH5 and the SPH10 for intercom conversation. Please follow
the same procedure as above to pair with these headset models.
A
D
B
D
B
C
Pairing A & D
8.2 Pairing with Other Sena Headset Models for Intercom
Conversation
Note:
The SMH5 cannot participate in three-way or four-way conference intercom
with the SMH10 or the SPH10. The SMH5 has a limited capability of having
two-way intercom with each other or with other Sena headsets such as the
SMH10 and the SPH10.
SMH10
You can set the configuration of the SMH10 by the voice menu
instruction as below.
1.To enter into voice configuration menu, press and hold the Jog
Dial for 12 seconds until the LED shows solid blue and you hear
high tone double beeps. You will also hear a voice prompt saying
“Configuration menu”.
2.Rotate the Jog Dial clockwise or counter-clockwise to navigate
between the menus. You will hear voice prompts for each menu
items as below.
3.You can enable the feature or execute the command by tapping
the Phone Button, or disable the feature by tapping the Jog Dial.
4.If any button is not pressed within 10 seconds, the SMH10 will exit
the configuration and goes back to stand-by.
5.If you want to exit the configuration immediately, rotate the Jog
Dial until you hear a voice prompt, “Exit configuration”, and tap
the Phone Button.
The voice prompt for each menu item is as below:
(1) VOX phone
(4) Delete all pairings
(2) VOX intercom
(5) Exit configuration
English
9.SMH10 CONFIGURATION SETTING
(3) Voice prompt
VOX phone
Exit configuration
VOX intercom
Delete all pairings
Voice prompt
9.1 Enabling/Disabling Voice Activated Phone Answering
Voice Prompt
“VOX phone”
Factory Default
Enable
Enable
Tap the Phone Button
Disable
Tap the Jog Dial
If this feature is enabled, you can answer incoming calls by simply
saying a word loudly enough. For example, when you hear a series
of beeps for an incoming call, you can answer the phone by saying
17
SMH10
“Hello” or any other word loudly. This is enabled from the factory but
you can disable this. If this mode is disabled, you have to tap the Jog
Dial or the Phone Button to answer an incoming call.
9.2 Enabling/Disabling Voice Activated Intercom
9.3 Enabling/Disabling Voice Prompts
Voice Prompt
“VOX intercom”
Factory Default
Disable
Voice Prompt
Enable
Tap the Phone Button
Factory Default
Enable
Tap the Jog Dial
Enable
Tap the Phone Button
Disable
Tap the Jog Dial
Disable
If this feature is enabled, you can initiate an intercom conversation
with the last connected intercom friend by speaking any word loudly
enough.The most effortless way to trigger intercom VOX is to blow
into the microphone as if blowing dust off the microphone. If you
start an intercom conversation by VOX, the intercom terminates
automatically when you and your intercom friend remain silent for 20
seconds. However, if you manually start an intercom conversation by
tapping the Jog Dial, you have to terminate the intercom conversation
manually.
However, even when this feature is enabled, if you terminate intercom
conversation manually with the Jog Dial, you are not able to start
intercom by voice temporarily. In this case, you have to tap the Jog
Dial to restart the intercom. This is to prevent repeated unintentional
18
intercom connections by strong wind noise. If you tap the Jog Dial to
start an intercom conversation, it is not terminated by 20 seconds of
silence. After turning SMH10 off and on, you can start intercom by
voice again.
“Voice prompt”
You can disable voice prompts by configuration setting, but the
following voice prompts are always on.
- Voice prompts for configuration setting menu
- Voice prompts for battery level Indicator
- Voice prompts for factory reset
9.4 Delete all Bluetooth Pairing Information
Voice Prompt
“Delete all pairings”
Factory Default
N/A
Execute
Tap the Phone Button
SMH10
9.5 Exit Voice Configuration Menu
Voice Prompt
“Exit configuration”
Factory Default
N/A
Enable
Tap the Phone Button
To exit voice configuration menu and get back to stand-by
mode, rotate the Jog Dial until you hear a voice prompt, “Exit
configuration”, and tap the Phone Button to confirm. Tapping the
Jog Dial is not available for this setting.
Rotate Jog Dial
Tap Phone Button
Tap Jog Dial
VOX Phone
Enable
Disable
VOX Intercom
Enable
Disable
Voice Prompt
Enable
Disable
Delete All Pairings
Execute
N/A
Exit Configuration
Execute
N/A
10.FUNCTION PRIORITY
English
To delete all Bluetooth pairing information of the SMH10, rotate the
Jog Dial until you hear a voice prompt, “Delete all pairings”, and
tap the Phone Button to confirm. Taping the Jog Dial is not available
for this setting.
The SMH10 operates in the following order of priority: (highest) Mobile phone,
Intercom,
Stereo music by audio cable
(lowest) Bluetooth stereo music
A lower priority function is always interrupted by a higher priority
function. For example, stereo music is interrupted by intercom call,
and intercom conversation is interrupted by incoming mobile phone
call.
Voice Configuration Menu & Button Operations
19
SMH10
11.STEREO MUSIC
You can listen to stereo music in two ways: with the enclosed stereo
audio cable or by Bluetooth wireless stereo.
AVRCP, you can use the SMH10 to remotely control music playback.
You not only can adjust the volume but also use the functions such as
play, pause, next track and previous track.
1.To adjust the volume, rotate the Jog Dial.
11.1 By Stereo Audio Cable
Plug your stereo MP3 player directly to the SMH10 by using the
enclosed 3.5mm stereo audio jack cable. To adjust the volume, rotate
the Jog Dial on the headset. You may adjust the volume on the MP3
player also.
MP3 Jack
11.2 By Bluetooth Wireless Stereo
The Bluetooth audio device must be paired with the SMH10 by following
the “Bluetooth Stereo Device Pairing” procedures described in the
6.2 chapter. The SMH10 supports the Audio/Video Remote Control
Profile (AVRCP), so if your Bluetooth audio device also supports the
20
2.To play or pause music, press and hold the Jog Dial for 1 second
until you hear a double beep.
SMH10
Note:
Bluetooth music is available only when the MP3 jack port remains open.
Please make sure the audio cable is unplugged from the clamp unit to play
music by Bluetooth.
12. MOBILE PHONE CALL MAKING AND ANSWERING
English
3.To track forward or track back, rotate while pressing the Jog Dial
clockwise or counter clockwise.
1.When you have an incoming call, simply tap the Phone Button or
the Jog Dial to answer the call.
2.You can also answer the incoming call by loudly speaking any word
of your choice if Voice Activated Phone Answering is enabled.
3.To end a call, tap the Phone Button or press the Jog Dial for 2
seconds until you hear a beep, or wait for the called person to end
the call.
4.To reject a call, press the Jog Dial for 2 seconds until you hear a
beep while the phone is ringing.
5.To transfer a call between the mobile phone and the headset
during the phone conversation, press the Phone Button for 2
seconds until you hear a beep.
6.There are several ways to make a phone call:
-Enter numbers on your mobile phone keypad and make a call.
Then the call is automatically transferred to the headset.
-For some older mobile phones which do not automatically
transfer calls to the headset, press the Phone Button after
entering phone numbers on the mobile phone keypad.
-Tap the Phone Button in stand-by mode to activate the voice
dialing of your mobile phone. For this, the voice dialing feature
21
SMH10
must be available on the mobile phone. Refer to your mobile
phone manual for further instruction.
-To redial the last number, double tap the Phone Button in standby mode. You will hear a voice prompt saying “Last number
redial”.
Tap Phone Button or Tap Jog Dial or Say “Hello”
Answer
End
Tap Phone Button or Press Jog Dial for 2”
Reject
Press Jog Dial for 2”
Transfer
Press Phone Button for 2”
Call
Use phone keypad
Redial
Double tap Phone Button
Voice Command
Tap Phone Button
13.TWO-WAY INTERCOM
13.1 Start and End Two-way Intercom
1.You can start an intercom conversation with one of any intercom
friends by tapping the Jog Dial: single tapping to intercom with
the first intercom friend, double tapping with the second intercom
friend, and triple tapping with the third intercom friend.
1st Intercom
Friend
2nd Intercom
Friend
Mobile Phone Call Button Operations
Note:
1. If you are using multipoint mobile phone connection and you have an
incoming call from the second phone during the call of the first phone,
then you may still receive the call from second phone. In this case, the
call from the first phone is on waiting mode. If you end a call, then it will
automatically guide you to the first phone call.
2. If you are using multipoint connection of mobile phone and GPS, you may
not be able to listen to the GPS voice instruction during the phone call.
22
3rd Intercom
Friend
Start Two-way Intercom Conversation
SMH10
Terminate
End Two-way Intercom Conversation
Start intercom
End intercom
1st intercom friend
2nd intercom friend
3rd intercom friend
Single tap
Double tap
Triple tap
Single tap
13.2 Intercom and Mobile Phone Call
1.When you have an incoming mobile phone call during an intercom
conversation, you will hear a ring tone. You can choose whether
to 1) answer the mobile phone call and stop the intercom
conversation, or 2) reject the phone call and stay on the intercom
conversation.
a.To answer the phone call and stop the intercom conversation,
tap the Jog Dial or the Phone Button. When you hang up the
phone call, the intercom will automatically be recovered.
b.To reject the phone call and stay on the intercom conversation,
press the J og Dial for 2 seconds until you hear a beep.
Unlike other motorcycle Bluetooth headsets, this prevents a
user from being dropped out of an intercom conversation by an
incoming mobile call.
2.When you have an incoming intercom call during a mobile phone
call, you will hear 4 high tone beeps, alerting you that there is an
incoming intercom call. You will also hear a voice prompt saying
“Intercom requested”. In this case, the intercom call does not
override the mobile phone call because intercom has lower
priority than mobile call. You have to hang up the mobile phone
call to make or receive an intercom call.
English
2. To terminate an intercom conversation, single tap the Jog Dial. Any
intercom connection with any intercom friend will be terminated
by a single tapping. A double or triple tapping will do nothing in
this case.
13.3 Intercom and GPS
If you pair a Bluetooth GPS to the SMH10 as described in 6.3 of
this user's guide, you can hear the turn-by-turn voice instruction
of the GPS while having an intercom conversation. The GPS voice
instruction interrupts intercom conversation, but it is automatically
reestablished after the GPS voice instruction ends.
23
SMH10
GPS
Voice Multipoint
Instruction Pairing
HFP
Smart Phone
Mobile Phone
Pairing
Smart Phone
HFP
+ Mobile Phone
Pairing
A2DP
Intercom
SMH10
Intercom
Pairing
Wired
Connection
Intercom Friend
Intercom and GPS voice instruction
13.4 Intercom and Two-way Radio
As described in 6.4 of this user's guide, you can use a two-way radio
and SMH10 Bluetooth intercom simultaneously by using the Sena
SR10, a Bluetooth Two-way Radio Adapter, along with the SMH10.
Incoming audio from the two-way radio is not interrupting an intercom
conversation but is heard in background. This is useful when you
have an intercom conversation with a passenger on the back seat and
use a two-way radio for group communication with other motorcycle
riders.
24
Two-way radio
Audio from
Two-way Radio
SMH10
Multipoint
Pairing
Intercom Intercom
Pairing
Intercom Friend
Wired
Connection
Sena SR10
Wired
Connection
Radar Detector
Intercom and Two-way Radio
GPS
SMH10
g
rin
Pa
i
First Friend
(B)
g
(A)
rin
You (A) can have a three-way conference intercom with two other
SMH10 friends (B & C) by establishing two intercom connections
at the same time. While a three-way conference intercom is in
progress, mobile phone connection of all three participants would be
temporarily disconnected, but as soon as the conference intercom
terminates or one of the participants leaves the intercom, all mobile
phones would be automatically reconnected. During the conference
intercom, if you have an incoming mobile phone call, terminate the
conference intercom to automatically reconnect the mobile phone
and receive the call.
i
Pa
14.1 Start Three-way Intercom
1. You (A) need to be paired with two other friends (B & C) for threeway conference intercom.
English
14.THREE-WAY CONFERENCE INTERCOM
Second Friend
(C)
2.Start an intercom conversation with one of the two friends in
your intercom group. For example, you (A) may start an intercom
conversation with the intercom friend (B). Or intercom friend (B)
may start an intercom call with you (A).
(A)
First Friend
(B)
Second Friend
(C)
25
SMH10
3. The second intercom friend (C) may join the intercom by making an
intercom call to you (A).
(A)
First Friend
(B)
Second Friend
(C)
4.Now you (A) and two SMH10 intercom friends (B & C) are having a
three-way conference intercom.
14.2 End Three-way Intercom
When you are a member of an active three-way conference intercom,
you can completely terminate the conference intercom or just
disconnect an intercom connection with one of your active intercom
friends.
1.Press the Jog Dial for 1 second until you hear a beep to terminate
three-way conference intercom completely. It terminates both
intercom connections with (B) and (C).
2.Tap or double tap the Jog Dial to disconnect intercom connection
with one of the two intercom friends accordingly. For example, by
single tapping the Jog Dial, you can just terminate the intercom
connection with the first intercom friend (B). However, you still have
the intercom connection with your second intercom friend (C).
Jog Dial Operation
(A)
Press for 1”
First Friend
(B)
Second Friend
(C)
Result
Disconnect (B) & (C)
Single tap
Disconnect (B)
Double tap
Disconnect (C)
End Three-way Intercom
26
SMH10
15.1 Start Four-way Intercom
You can have four-way conference intercom with three other SMH10
users by adding one more intercom participant to the three-way
intercom. While you are having three-way intercom as above in
section 14.1, a new participant (D), who is an intercom friend of your
intercom friend (C), may join the conference intercom by making
an intercom call to your intercom friend (C). Please note that in this
case, the new participant (D) is an intercom friend of (C), not of you
(A).
You
(A)
New Participant
(D)
= Intercom Friend of (C)
First Friend
(B)
Second Friend
(C)
15.2 End Four-way Intercom
English
15.FOUR-WAY CONFERENCE INTERCOM
As same in the case of three-way intercom, you can completely get
out of the four-way conference intercom or just disconnect a single
intercom connection.
1. Press the Jog Dial for 1 second until you hear a beep to
terminate four-way conference intercom. It terminates the intercom
connections between you (A), and your intercom friends (B) and
(C).
2.Tap or double tap the Jog Dial to disconnect the intercom
connection with one of the two intercom friends accordingly.
However, when you disconnect the second friend (C) by double
tapping the Jog Dial, you will be disconnected with the third
participant (D) as well. This is because the third participant (D) is
connected with you via the second friend (C).
Jog Dial Operation
Press for 1”
Single tap
Double tap
Result
Disconnect (B), (C) & (D)
Disconnect (B)
Disconnect (C) & (D)
End Four-way Intercom
27
SMH10
16.THREE-WAY CONFERENCE PHONE CALL
WITH INTERCOM PARTICIPANT
You can have a three-way conference phone call by adding an
intercom friend to the mobile phone conversation. While having
a mobile phone call, make an intercom call to one of the intercom
friends by tapping the Jog Dial to form a three-way conference call
with the person on the mobile phone line. To disconnect the intercom
first and go back to your private mobile phone call, terminate the
intercom by tapping the Jog Dial. To end the mobile phone call first
and maintain the intercom conversation, press the Jog Dial for 2
seconds, or tap the phone button, or wait for the person on the mobile
phone line to end the call.
Start
Tap Jog Dial while having a mobile phone call
End intercom first
End phone call first
Tap Jog Dial
Press Jog Dial for 2”
or
Tap Phone Button
or
Wait for the called person to end the call
Start & End Three-way Conference Phone Call
28
17.INTERCOM FAILURE
When you try to start an intercom conversation with an intercom friend
who is already having a conference intercom with other riders or a
mobile phone call, you will hear a low tone double beep signifying an
intercom busy signal. In this case, you have to try again later.
18.INTERCOM RECONNECTION
If your intercom friend goes out of range while having an intercom
conversation, you may hear static noise and eventually the intercom
will be disconnected. In this case, the SMH10 automatically tries to
reconnect the intercom every 8 seconds and you will hear high tone
double beeps until the intercom is reestablished. If you don’t want to
make a reconnection, tap the Jog Dial to stop the attempt.
SMH10
1.To restore the SMH10 to factory default settings, press and hold
the Phone Button for 12 seconds until the LED shows solid red
and you hear double beeps. You will hear a voice prompt saying
“Factory reset”.
2. Within 5 seconds, press the Jog Dial to confirm reset. The headset
will be restored to factory setting and switched off automatically.
You will hear a voice prompt saying “Headset reset, good-bye”.
3.If you don’t press the Jog Dial within 5 seconds, the reset attempt
is canceled and the headset returns to stand-by mode. You will
hear a voice prompt saying, “Canceled”.
20.FAULT RESET
English
19.RESET TO FACTORY DEFAULT SETTINGS
When the SMH10 is not working properly or is in faulty status for any
reason, you may reset by pushing the pin-hole reset button at the
back of the headset main unit. Insert a paper clip into the reset pinhole and press the reset button for a second with light pressure. The
SMH10 will be switched off, and you have to turn the system back
on and try again. However, this will not restore the headset to factory
default settings.
21.FIRMWARE UPGRADE
The SMH10 supports firmware upgrade function. Please visit Sena
Bluetooth web site at www.senabluetooth.com to check the latest
software downloads.
29
SMH10
Case 2
22.CASE STUDY
•iPhone for mobile phone call and stereo music streaming
•ZumoTM 660/665 for GPS voice instruction
•SMH10 for two-way intercom
Case 1
•iPhone for mobile phone call and stereo music streaming
•ZumoTM 550 or ZumoTM 220 for GPS voice instruction
•SMH10 for two-way intercom
iPhone
Mobile Call Pairing: 6.1
Music
iPhone
Intercom
Conversation
Mobile Call Pairing: 6.1
Music
SMH10
Intercom
Conversation
SMH10
30
Pairing: 8.1
GPS
Voice
SMH10
Pairing: 6.3.1 ZumoTM 550 or
ZumoTM 220
Pairing: 8.1
GPS
Voice
SMH10
Pairing: 6.3.1 ZumoTM 660/665
SMH10
Case 3
Case 4
•Feature phone for mobile phone call
•iPod Touch for stereo music streaming
•Two other SMH10s for three-way conference intercom
ZumoTM 660/665
Feature Phone
Mobile Call
Music
GPS Voice
SMH10
Mobile Pairing: 6.1
Call
Multipoint
Mobile Call
Intercom
Conversation
SMH10
English
•iPhone for mobile phone call via ZumoTM 660/665
•ZumoTM 660/665 for GPS voice instruction and stereo music
streaming
•SMH10 for two-way intercom
Intercom
Conversation
Mobile Phone
SMH10
Pairing: 8.1
Music
SMH10
Pairing: 6.2
iPod
Touch
Intercom
Conversation Pairing: 8.1
SMH10
31
SMH10
Case 5
Case 6
•iPhone for mobile phone call
•iPod Touch for stereo music streaming
•TomTom® Rider2 for GPS voice instruction
•SMH10 for two-way intercom
•iPhone for mobile phone call and stereo music streaming
•Sena SR10 for two-way radio, GPS voice instruction, and radar
detector alarm
•SMH10 for two-way intercom
iPhone
iPhone
Mobile Pairing: 7.2
Call
Intercom
Conversation
SMH10
Pairing: 8.1
SMH10
Pairing: 6.2
Pairing: 6.3.1
TomTom® Rider 2
Pairing: 6.1
Wired
Connection
Tow-way radio
GPS Voice
Alarm
Music
GPS
Voice
32
Mobile Call
Music
Two-way radio
iPod
Touch
SMH10
Pairing: 6.4
Intercom
Conversation Pairing: 8.1
SMH10
Wired
Connection
Sena SR10*
Wired
Connection
Radar Detector
GPS with headphone
jack/audio line-out
SMH10
MAINTENANCE AND CARE
The product has an internal, non-removable, rechargeable battery.
Do not attempt to remove the battery from the device as you may
damage the device. The battery can be charged and discharged
hundreds of times, but it will eventually wear out. Recharge the
battery only with Sena approved chargers designated for this device.
Use of an unapproved charger may present a risk of fire, explosion,
leakage, or other hazard.
The SMH10 should be treated with care and the following suggestions
will help you protect your warranty coverage.
1.Do not use or store the device in dusty, dirty areas. Its moving
parts and electronic components can be damaged.
2.Do not store the device in hot areas. High temperatures can
shorten the life of electronic devices, damage batteries, and wrap
or melt certain plastics.
3.Do not store the device in cold areas. When the device returns to
its normal temperature, moisture can form inside the device and
damage electronic circuit boards.
4.Do not attempt to open the product.
5.Do not drop or knock the device. Rough handling can break
internal circuit boards and fine mechanics.
6.Do not use harsh chemicals, cleaning solvents, or strong
detergents to clean the device.
7.Do not paint the device. Paint can clog the moving parts and
prevent proper operation.
Always try to keep the battery between 15℃ and 25℃ (59℉ and
77℉). Extreme temperatures reduce the capacity and lifetime of the
battery. A device with a hot or cold battery may not work temporarily.
Battery performance is particularly limited in temperatures well
below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries
may also explode if damaged. Never use any charger that is
damaged. Operating times are estimates only and depend on the
devices used together, features used, battery age and condition,
temperatures to which battery is exposed, and many other factors.
English
BATTERY INFORMATION
These suggestions apply equally to the headset main unit, speakermicrophone clamp unit, or power charger.
33
SMH10
DISPOSAL
CERTIFICATION AND SAFETY APPROVALS
The crossed-out wheel bin symbol on the product,
literature, or packaging reminds you that all electrical
and electronic products, batteries, and accumulators
must be taken to separate collection at the end of their
working life. This requirement applies to the European
Union and other locations where separate collection
systems are available. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please do not
dispose of these products as unsorted municipal waste, but hand it
in at an official collection point for recycling.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
•This device may not cause harmful interference.
•This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
34
SMH10
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. The
antenna used for this transmitter must not transmit simultaneously
with any other antenna or transmitter, except in accordance with
FCC multi-transmitter product procedures.
FCC Caution
Any changes or modifications to the equipment not expressly
approved by the party responsible for compliance could void user’s
authority to operate the equipment.
CE Declaration of Conformity
This product is CE marked according to the provisions of the R&TTE
Directive (99/5/EC). Hereby, Sena declares that this product is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. For further information please
consult www.senabluetooth.com.
Please note that this product uses radio frequency bands not
harmonized within EU. Within the EU this product is intended to
be used in Austria, Belgium, Denmark, Finland, France, Germany,
Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal,
Spain, Sweden, United Kingdom and within EFTA in Iceland, Norway
and Switzerland.
English
•Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Statement
This device complies with Industry Canada license-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Bluetooth License
The Bluetooth® word mark and logos are owned by the Bluetooth
SIG, Inc. and any use of such marks by Sena is under license. Other
trademarks and trade names are those of their respective owners
The SMH10 is compliant with and adopts the Bluetooth® Specification
3.0 and has successfully passed all interoperability tests that are
specified in the Bluetooth® specification. However, interoperability
between the device and other Bluetooth®-enabled products is not
guaranteed.
35
SMH10
WAIVER AND GENERAL RELEASE
By using the product you waive all substantial legal rights including
the right to sue. Please read the following carefully before using the
device. If you do not accept all terms of this agreement, you should
immediately return the product for a full refund. By using the headset
you agree to be bound to this agreement and forfeit the right to sue.
Using a communication device while riding a motorcycle, scooter,
moped, ATV, quad-bike or any other vehicle or equipment, whether
on land, water or air (jointly referred to as “Vehicle”) requires your
complete and undivided attention. Sena Technologies, Inc., including
its Officers, Directors, Affiliates, Parent Company, Representatives,
Agents, Contractors, Sponsors, Employees, Suppliers and Resellers
(jointly referred to as the “Company” or “Sena”) strongly advise you to
take all necessary precautions and remain alert to the traffic, weather
and road conditions if you choose to use the product headset,
including all derivative models irrespective of its commercial name
or branding (the “Device”), and stop your Vehicle on the roadside
prior to initiating or receiving calls. Any publications, advertisements,
announcements or similar notes that refer to using the Device
while riding a Vehicle are solely intended to address its technical
capabilities and should not be misconstrued as if encouraging users
to operate the Device while actively involved in traffic.
36
By way of purchasing this Device and not returning it for a full
refund (see below), you are irrevocably releasing, indemnifying
from any liability, loss, claim and expense (including attorney’s fees)
and holding Sena harmless for any bodily injuries, harm or death
as well as losses or damages in goods, to any Vehicles including
your own, or to any property or asset that belong to you or to third
parties, any of which may result from using the Device under any
circumstances or conditions and irrespective of jurisdiction. Sena will
not be responsible for any physical damages, irrespective of reasons,
conditions or circumstances, including malfunctioning of the Device,
and all risks associated with operating it rest solely and entirely with
the user of this Device, irrespective of whether the Device is used by
the original purchaser or any third party.
Sena hereby notifies you that using this Device may also be in
contravention to local, federal, state or national laws or regulations,
and that any use of the Device is entirely at your sole risk and
responsibility.
1.You, your heirs, legal representatives, successors or assigns,
hereby voluntarily and forever release, discharge, indemnify and
hold harmless Sena from any and all litigation, claims, debts,
demands, actions and liability which may arise, directly or
indirectly, from using the Device for any distress, pain, suffering,
discomfort, loss, injury, death, damages to or in respect to any
SMH10
any losses and/or damages, whether caused in whole or in part by
the negligence or other conduct of others, including the Company.
5.You confirm that you have read this release of liability and fully
understand its terms and that you have given up substantial rights
by not returning the Device for a full refund (see refund option
below).
English
person or property however caused, WHETHER ARISING FROM
THE NEGLIGENCE OR OTHERWISE, and which may hereafter
accrue to you on some future date as a result of said use, to the
fullest extent permitted by law.
2.You fully understand and assume the risks in using the Device,
including risk of negligent acts or omissions by others.
3.You confirm that you are physically capable to use the Device and
that you have no medical conditions or needs that may infringe
upon your abilities to do so in a safe manner. You confirm that you
are at least eighteen (18) years of age and that you have been
advised of the risks associated with the use of the Device. You
further confirm that you will not consume any alcohol that may
affect your alertness or any mind-altering substance, and will not
carry, use or consume these substances before or during the use
of the Device.
4.You fully acknowledge our warnings and understand that: (a) risks
and dangers exist in using the Device while in traffic, including
but not limited to injury or illness, strains, fractures, partial and/or
total paralysis, death or other ailments that could cause serious
disability; (b) these risks and dangers may be caused by the
negligence of the manufacturers or its agents or any third party
involved in designing or manufacturing the Device; (c) these risks
and dangers may arise from foreseeable or unforeseeable causes.
You hereby assume all risks and dangers and all responsibility for
Two-Year Limited Warranty
Sena Technologies, Inc. (“Sena”) warrants that this product
(“Product”) shall conform to and perform in accordance with
published technical specifications and the accompanying written
materials, and shall be free of defects in materials and workmanship,
for a period of two (2) year from the date of purchase by the first
consumer purchaser of the Product. The limited warranty extends
only to the original consumer purchaser of the Product and is not
assignable or transferable to any subsequent purchaser/end-user.
This warranty is limited to the repair and/or replacement, at Sena’s
discretion, of defective or non-conforming Product, and Sena shall
not be responsible for the failure of the Product to perform specified
functions, or any other non- conformance caused by or attributable
to: (a) any misapplication or misuse of the Product; (b) failure of
Customer to adhere to any of Sena’s specifications or instructions;
(c) neglect of, abuse of, or accident to, the Product; or (d) any
37
SMH10
associated or complementary equipment or software not furnished
by Sena.
Limited warranty service may be obtained by delivering the Product
to Sena or to the international distributor it was purchased through
and providing proof of purchase or receipt date. Customer agrees to
insure the Product or assume the risk of loss or damage in transit, to
prepay shipping charges to Sena, and to use the original shipping
container or equivalent.
Limitation of Liability
EXCEPT AS EXPRESSLY PROVIDED HEREIN, SENA MAKES NO
WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED, WITH RESPECT
TO ANY EQUIPMENT, PARTS OR SERVICES PROVIDED PURSUANT
TO THIS AGREEMENT, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NEITHER SENA NOR ITS DEALER SHALL BE
LIABLE FOR ANY OTHER DAMAGES, INCLUDING BUT NOT LIMITED
TO DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, WHETHER IN AN ACTION IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE AND STRICT LIABILITY), SUCH AS, BUT
NOT LIMITED TO, LOSS OF ANTICIPATED PROFITS OR BENEFITS
RESULTING FROM, OR ARISING OUT OF, OR IN CONNECTION WITH
THE USE OF FURNISHING OF EQUIPMENT, PARTS OR SERVICES
38
HEREUNDER OR THE PERFORMANCE, USE OR INABILITY TO USE
THE SAME, EVEN IF SENA OR ITS DEALER HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL SENA
OR ITS DEALERS TOTAL LIABILITY EXCEED THE PRICE PAID FOR
THE PRODUCT.
Return for Full Refund
IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE
CONDITIONS, YOU MAY RETURN THIS DEVICE TO SENA FOR A
FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 14
BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE
AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING
SO, PLEASE REFER TO THIS SECTION. BY NOT RETURNING THE
DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE
EXPLICITLY IN AGREEMENT WITH THE ABOVE AND RENOUNCE
ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST SENA
AS DEFINED ABOVE.
SMH10
English
WARNING
Sena informs that using this device in public traffic may not be
authorized by the law. Please check your local law and use this
device only out of public traffic such as private properties or closed
circuits. If the simultaneous use of both ear speakers while riding a
motorcycle is prohibited by your local law, please use only a single
ear speaker while riding. Sena denies any liability should you choose
not to respect this warning.
Using the headset with loud volume may be harmful to your eardrums
and cause hearing loss. Please maintain proper volume level to
protect your ears.
39
3.1.0
www.senabluetooth.com
User's Guide for Firmware v4.2