Dimplex Langbrook LBK5 Operating instructions

Langbrook 5kW (LBK5)
Please hand these instructions to the stove user when installation is complete.
Leave the system ready for operation and instruct the user in the correct use of the
appliance and operation of controls.
Installation should only be carried out by a suitably qualified installer that is registered
with HETAS (UK) or with the Irish Nationwide Fireplace Organisation (INFO).
Installation must comply with Building Regulations.
08/51568/0 - Issue 2
The product complies with the European Safety Standards EN13240 for Room heaters fired by solid fuel.
1
B
F
C
K (Dia)
H
G
D
A
J
E
Table 1 - Dimensions
A
B
C
D
E
F
G
H
J
K
Langbrook 5kw
600
500
30
250
105
368
23
110
472
127
Note: All Dimensions in mm. Dimensions stated may be subject to a slight ± variation. ( 25.4mm = 1”)
Table 2 - Technical Specification
Nominal heat output
Efficiency
CO Emission (@13% O2)
Flue Gas Temp
Flue Gas Mass Flow
Langbrook 5kw
Wood
kW
Solid Fuel (Ancit)
kW
5.3
Wood
%
77.0
Solid Fuel (Ancit)
%
82.5
Wood
%
0.32
Solid Fuel (Ancit)
%
0.38
Wood
°C
306
Solid Fuel (Ancit)
°C
249
Wood
g/s
4.0
Solid Fuel (Ancit)
g/s
3.3
hr
1
Refuel Period
Safe Distance to Combustibles
Sides
mm
Rear
mm
Flue Outlet Size
mm / inch
Product Weight
kg
Additional Room Ventillation Required
cm²
5.0
500
650
127 / 5
98.7
see table 4
2
x4
A
!
3
4
Solid, non-combustible
material e.g. masonary
or concrete
H
T
See Table 3
T
MIN m
m
150
X
mm
0
30
X
MIN
150mm
MIN
125mm
Table 3 - Position of Hearth & Appliance from adjacent walls
Hearth distance ‘X’ from wall
Appliance distance from walls
Min Wall Thickness ‘T’
Min Wall height ‘H’
0 - 50mm
200mm
Height of appliance +300mm
or 1200mm from hearth
(whichever is greater)
0mm
0mm
51 - 150mm
75mm
0 - 150mm
150 - 300mm
75mm
+150mm
+300mm
No Minimum Requirement
5
6
Seal with fire
proof lagging
150
150
150 Max
150
MIN 840mm
300
FREESTANDING ON
NON COMBUSTIBLE HEARTH
MIN 12mm THICK
MIN 840mm
45°
Max
7
8
Seal gap with
fire-proof lagging
SEAL
150 max
150 max
9
10
B
C
D
A
CLOSURE
PLATE
Langbrook 5kW (LBK5)
-1-
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
Please read these instructions carefully before installing
or using this appliance. Failure to do so may result in
damage to persons and property.
Installation of this appliance must be carried out by a
suitably qualified competent person in accordance with
all Building Regulations, including those referring to Local
Authority Bye-Laws, National and European Standards
and Codes of Practice.
Do not install this appliance on a shared flue.
This appliance operates at very high temperatures and
retains its heat for a period after use. Do not touch any
surfaces while in use. All persons including children and
the infirm should be warned of this and not allowed to
touch any surfaces while in use. Please use a suitable
fireguard to prevent contact when in use.
Do not place any photographs, paintings, TV’s or other
combustible items near the appliance as exposure to
hot surfaces will cause damage. Maintain safe distances
from combustibles in all cases in accordance with these
instructions – please refer to installation.
The operator must use the tools provided. The mitten
provided is a tool.
Do not fit an extractor fan in the same room as this
appliance.
Ensure that there is adequate ventilation in the room in
accordance with building standards. Do not obstruct any
of the air inlets or outlets on the appliance.
A flue damper should not be fitted when burning solid
fuels other than wood.
This appliance is for domestic heating use only in
accordance with these operating instructions. Do not
make any unauthorised changes to the appliance.
Only use recommended fuels. Do not burn petroleum coke
fuels, household waste or plastic in this appliance.
Burn only fuels with a low moisture content - burning soft
or wet fuels such as unseasoned timber or peat will only
result in a build up of tar in the stove and the chimney
and will cause staining of the glass.
Do not use flammable liquids to ignite the fire.
Avoid the use of aerosols in the vicinity of the stove when
it is in operation.
Clean your chimney at least twice a year and clean the
flue way weekly to ensure there are no blockages. Do not
allow a build up of ash to occur in the ash pan as this will
cause the grate to burn out prematurely.
Regular maintenance should be carried out by a
Competent Engineer.
Health and Safety Precautions
Handling: Adequate facilities must be available for the unloading
and handling of this appliance. This product is heavy and should
be handled with care. When handling or servicing this stove care
should be taken to avoid the possibility of personal injury. Use
protective clothing.
Fire Cement/Glue: Some types of fire cement/glue are caustic
and should not be allowed to come into contact with the skin. Use
suitable protective gloves when handling. In case of contact, wash
immediately with plenty of water.
Asbestos: This appliance contains no asbestos. If there is a
possibility of disturbing asbestos as a result of installation then
specialist guidance must be sought prior to installing.
Installation Instructions
General
These instructions give a guide for the installation of the stove but
in no way absolves the installer from responsibilities to conform
to all relevant standards relating to the installation of solid fuel
appliances.
We recommend that for UK installations a HETAS registered
installer should be used, who will be able to give a Certificate of
Compliance that installation complies with Building Regulations.
In Ireland a registered installer from the Irish Nationwide Fireplace
Organisation should be used.
Please note that to the best of our abilities these instructions are
correct at time of printing, however we cannot be held responsible
for any differences in legislation which may occur in the future.
Assembly of the stove
To make the product easier for handling on installation, remove
the baffle plate, side bricks, back brick and ashpan. Place these
in a secure place to avoid damage. These must be refitted after
installation. The legs and other fixings are packed in the ashpan
for safe keeping in transport. Fix the legs to the underside of the
product using the bolts provided (Fig 2).
The stove is supplied ready for rear flue connection. For Top
flue connection (Fig 3) remove the flue cap from the top plate by
removing the screws on underside of top plate inside the stove.
Reposition the flue cap on the rear flue outlet and tighten all fixing
screws to ensure it is air tight.
Chimney
Before installing, check the chimney is in good condition; dry and
free from cracks and obstructions. The diameter of the chimney
flue should not be less than 150mm and not more than 230mm.
If any of these requirements are not met, the chimney should be
lined by a suitable method by a qualified person.
The chimney height and the position of the chimney terminal should
conform to Building Regulations. If you have any doubts about the
suitability if your chimney, consult your local dealer or stockist. The
chimney must be swept before connection to the stove and swept
every six months thereafter.
If there is no existing chimney then either a prefabricated block
chimney or a twin walled insulated stainless steel flue to BS4543
can be used. These chimneys must be fitted in accordance with
the manufacturers instructions and in compliance with Building
Regulations.
This product must not be installed on a shared flue.
-2-
Flue Deposits
If the chimney was previously used as an open fire, it is possible
that the higher flue gas temperatures generated by the stove
may loosen deposits that were previously adhered to the inner
surface of the flue pipe which could cause blockage of the flue
pipe. We recommend that in this situation a second sweeping of
the chimney should be carried out within one month of initial stove
use after installation.
Flue Draught
The chimney should be checked before the stove is installed to
ensure that there is adequate flue pull. The draught can be checked
initially by using a smoke match close to the flue opening. If the
chimney doesn’t pull the smoke it may suggest that the chimney
needs further attention. Any remedial work to the chimney flue
should be carried out by a suitably Qualified Engineer.
A flue draught of minimum 12 Pascal to maximum 25 Pascal is
required for satisfactory appliance performance. The flue draught
should be checked under fire at high output and if it exceeds the
recommended maximum a flue draught stabiliser (or flue damper
as it is also known) must be fitted so the rate of burning can be
controlled and prevent overfiring.
Room Ventilation
For safe operation this stove must be provided with combustion
air supply in addition to normal room ventilation, in accordance
with Building Regulations. Minimum ventilation requirements vary
depending on whether the dwelling is considered to be of standard
construction or of airtight construction, or if a flue draught stabiliser
has been fitted. The required open air vent sizes are as follows:
Table 4 - Additional Room Ventilation Required
Standard build dwellings {air permeability >5.0m³ /(h.m²)}
No Flue Stabiliser
2 cm²
With Flue Stabiliser
18 cm²
Airtight build dwellings {air permeability ≤5.0m³ /(h.m²)}
No Flue Stabiliser
29 cm²
With Flue Stabiliser
45 cm²
An extractor fan must not be used in the same room as this
appliance.
Floor Protection & Installation Clearances
In all instances the stove should be positioned on a noncombustible hearth. The construction of the hearth must conform
to Building Regulations, must be firm, non-combustible and capable
of supporting the stove. Care should be taken to ensure the stove
is level and the hearth is secure.
The stove can be installed in suitably sized recess, either purpose
built or an existing fireplace. In this instance a solid constructional
hearth of minimum 125mm must be used, including the thickness
of the floor and any decorative top surface (e.g. tiling). We
recommend a permanent free air gap of at least 150mm should
be left around the sides where possible and 300mm around the
top to obtain maximum heat output and for access to the rear of
the stove. Place the product in the desired location on fireproof
hearth taking note of installation clearances from adjacent walls
(Fig 4). Adjust the screws on the bottom of the feet to ensure the
stove is level and steady (see ‘A’ Fig 2).
The stove can also be installed freestanding in the room. In this
instance a reduced thickness hearth may be used, which must
be made from non-combustible board, sheet or tiles of minimum
thickness12mm. (Fig 5) shows the minimum distances required
from the hearth edge to the sides of the stove.
In all cases allow an apron of at least 300mm at the front of the
stove in case of spills when de-ashing.
Table 5 shows the minimum safe distances to combustable
materials which must be observed. Any surrounding combustible
material should not exceed 80°C.
Table 5
Sides
Rear
Langbrook 5kW
500mm
650mm
Flue Pipes
The flue pipe used to connect to the stove should be made of cast
iron, 316 grade stainless steel or vitreous enamelled steel, nominal
thickness 1.2mm. The diameter of the flue pipe should be 125mm
(5”) for the Langbrook 5kW model.
Connect the flue pipe to the stove making sure that it fits snugly
into the base of the flue collar . Seal the collar and flue connection
with fire cement or with other suitable high temperature sealant.
Add flue sections as required; note that all flue sockets must face
upwards. Ensure that the flue pipe end is no closer than 76mm
to the side or rear of the chimney walls. It is essential that all
connections between the stove and the chimney flue are sealed
and made airtight.
Avoid using bends greater than 45° to the vertical (Fig 6). All flue
pipes should be as close to vertical where possible. For rear flue
connection the length of the horizontal run of the flue pipe should
not exceed 150mm (Fig 7). Both chimney and flue pipe must be
accessible for cleaning and if ALL parts of the chimney cannot be
reached, a soot door must be fitted to enable this to be done.
This product should not be installed on a shared flue.
Existing Fireplace
An existing fireplace opening can be bricked up or sealed with a
register plate, 2.5mm sheet steel or concrete. A short length of
flue pipe may then be used to connect the stove to the chimney.
Ideally the old fireplace should be filled in so that there is a smooth
streamlined entry into the flueway. (Fig 7)
Typical installation for Inglenook Fireplaces
Inglenook fireplaces can have very large bore chimneys (Fig 8).
Check with your installer – you may need a stainless steel flexible
flue liner for solid fuel fitting.
Flue Damper (Not Supplied)
When burning wood, a flue damper may be fitted to reduce the
draught through the stove if the draught is too high. When the
damper is set in the open position the chimney draws at full
draught, increasing the volume of air flow through the stove and
flue. Shutting the damper restricts the flow, slowing the rate of
burning. The damper should be fitted to the stove flue and should
be the same size as the flue pipe. As a rule it should be fitted no
closer than 700mm from the flue outlet of the appliance.
A flue damper should not be fitted when burning solid fuels
other than wood.
Commissioning
Upon completion of installation, the stove and flue system should
be tested by a suitably qualified person to make sure it is safe for
normal use. A smoke draw test should be completed to check for
soundness of joints and seals and also that all smoke and fumes
are taken from the appliance up the chimney and emitted safely.
First warm the flue with a blowlamp or similar for about 10 minutes.
Place a lit smoke pellet on the centre of the grate with the air
-3-
controls open. Close the door – the smoke should be drawn up the
flue and be seen to exit from the flue terminal. Complete the test
with all windows and doors shut in the room where the appliance
is fitted.
If a ceiling fan is present it must be operated on max for the duration
of the test. If there are any extraction fans in adjacent rooms these
too must be operated on maximum setting during the test with the
interconnecting doors open. If any spillage occurs, recheck the
suitability of the flue system making sure there is adequate air
supply to the room (as per Building Regulations).
Light the appliance and slowly increase the temperature to
operating levels. Open the main fire door when the appliance
reaches normal operating condition and carry out a spillage test
using a smoke match or pellet around the door opening. If any
spillage occurs, open all windows, allow the fire to go out and
recheck the flue system and ventilation.
Operating Instructions
Warning: The door and operating handles become hot when
the stove is in use. For your safety use the glove provided.
Initial Firing of Stove
We recommend that you have two to three small fires before you
operate your stove to maximum heat output. This is to allow the
paint to cure and the castings to relax and consolidate location.
We recommend this ‘running in’ procedure after long idle periods
to preserve the life of the stove. During this you may notice an
unpleasant smell. It is not toxic but for your own sake we would
suggest that during this period you leave all doors and windows
open.
Air Controls
Primary air is controlled via the sliding vents (A - Fig 9) in the bottom
of the door; this provides a conventional air draught to the bed of
the fire. (+) indicates more air, (-) indicates less air, (+) and (-) are
marked on the primary and secondary air controls.
Secondary air is controlled via the sliding vent (B - Fig 9) above
the door. It is this ‘Airwash’ that keeps a clean and uninterrupted
view of the fire, also aiding in good secondary combustion of fuel
and reducing emissions into the chimney and environment.
Lighting the Stove
Place fire lighters or paper and kindling on the grate. Light the
fire at base leaving all air controls open. Allow the fuel to reach a
steady glow across the grate and build the fire up gradually. Once
you have a good fire established across the grate bed, further fuel
can be added as required.
Running the Stove
When your fuel is well alight you can start to restrict the primary
air intake. If you are only burning wood the primary air control can
be fully closed. If you are burning solid fuel you will require more
primary air. Your stove is burning with maximum efficiency when
a bright fire is achieved using minimum air inlet.
The stove can be banked up for long periods. When burning solid
fuel empty the ash pan. Open air controls and let the fire burn
brightly for a short period. Refuel and close air controls; the exact
setting required will depend on the fuel used and the chimney draw
so some practice may be necessary. To revive the fire, open air
controls until the fire is burning brightly, de-ash if necessary and
refuel. Set air controls as required. The stove is not suitable for
overnight burning.
Notes on Wood Burning
Wood burns best on a bed of ash and it is therefore only necessary
to remove surplus ash from the grate occasionally. Burn only
dry, well seasoned wood, which should have been cut, split and
stacked for 12 months with free air movement around all sides
of the stack to enable it to dry out. Burning wet or unseasoned
wood will create tar deposits in the stove and chimney and will not
produce a satisfactory heat output. When loading wood, make sure
that the end grain of the wood in the stove is pointing away from
the glass otherwise the moisture and gases coming from the end
grain of the wood will dirty the glass.
Table 5 - Maximum log lengths
Langbrook 5kW
350mm (14”)
Notes on Solid Fuel burning (Other than Wood)
Always de-ash the grate before refuelling and do not let the ash
build up to the underside of the grate bars. Solid fuel produces
ash, which if allowed to build up will stifle the air flow through the
grate and will eventually cause the fire to die. It is important it is
to empty the ash pan after each firing of the stove. Air passing
through the firebed cools the grate. Distortion or burning out of the
grate bars is nearly always caused by ash being allowed to build
up on the underside of the grate. With some solid fuels a residue
of burnt fuel or clinker will accumulate on the grate. Allow the fire
to go out periodically to remove this.
We recommend the majority of approved manufactured
smokeless fuels. Note that different types of fuel will give different
performances. Use as an incinerator for household waste is not
recommended as fumes from plastic, etc will cause pollution to
the atmosphere and will cause damage to the stove. Should any
difficulties arise over fuel quality or suitability, consult your local
supplier or contact the Solid Fuel Advisory Service.
Petroleum coke fuels or household waste should not be
burned on this appliance.
De-Ashing
To de-ash the grate draw the riddle lever forwards and backwards
with a slow positive action (D - Fig 9).
The ash pan should be emptied each time after operating the stove
so not to let build up of ash occur. Where possible, it is best to
wait until the stove and ash has cooled before removing the ash
pan. To remove, open the stove door by lifting the handle upward
(C - Fig 9) then using the hand tool lift the ash pan out of the fire
(Fig 10). For efficient burning of your appliance, make sure the
grate is clear of burnt debris; e.g. nails, etc.
Shut down Periods
If shutting down the stove for long periods (e.g. for summer months)
make sure that all ash is removed from the stove and that the
chimney flue ways and baffle plate are brushed clean. When the
stove is cold a vacuum cleaner may be used to remove any residual
ash or soot. Close the door and leave all air inlets open fully. This
action will ensure air circulation through the appliance and will help
to avoid corrosion and condensation within the appliance during
this shut down period.
Safety Notes for Your Guidance
FIRES CAN BE DANGEROUS.
Always use a fire guard in the presence of children, the elderly
or the infirm. Inform all persons the dangers of high temperatures
during operation of the appliance including the stove pipe.
Use operating tools provided.
-4-
DO NOT OVER FIRE.
It is possible to fire the stove beyond its design capacity. This could
damage the stove, so watch for signs of over firing. If any part of
the stove starts to glow red, the stove is in an over fire situation
and the controls should be adjusted accordingly to reduce air
intake. Never leave the stove unattended for long periods without
adjusting the controls to a safe setting. Careful air supply control
should be exercised at all times.
Warning - Fume Emissions
Properly installed and operated, this appliance will not emit fumes.
Occasional fumes from de-ashing and refuelling may occur.
Persistent fume emission must not be tolerated. If fume emission
does persist, then the following immediate action must be taken:
1. Open doors and windows to ventilate the room.
2. Let the fire out, or eject and safely dispose of fuel from the
appliance.
3. When the stove has cooled, check for chimney flue blockage
and clean if required.
Do not attempt to relight the fire until the cause has been
identified. If necessary seek professional advice.
General Maintenance
Baffle Plate: This should be removed at least once a month to
prevent any build up of soot or ash, which could lead to blocked flue
ways and dangerous fume emission. If the baffle plate is removed
the chimney/flueway can be swept through the appliance.
Stove Body: The stove is finished with a heat resistant paint and
this can be cleaned with a soft brush. Do not clean while the stove
is hot, wait until it has cooled down. The finish can be renovated
with a suitable brand of stove paint.
Glass Panels: Clean the glass panels when cool with a proprietary
glass cleaner. Highly abrasive substances should be avoided as
these can scratch the glass and make subsequent cleaning more
difficult. Wet logs on heated glass, a badly aimed poker or heavy
slamming of the doors could crack the glass panel. The glass will
not fracture from heat.
Chimney: Check your chimney each year before starting to use
your stove for the winter. Birds may have nested in the chimney or
masonry may have cracked. Both chimney and flue pipe must be
swept at least once a year by a Qualified Chimney Sweep.
To avoid a build up of soot on the baffle plate (the plate inside the
stove above the grate) it must be removed and cleaned periodically.
This plate locates the back and side firebricks so note its position
before removal. To remove, lift the baffle plate and remove the side
bricks; this will allow the plate to drop and aid removal. To replace,
position baffle plate on back plate, lift plate and replace the side
bricks, making sure it has located in position. This must be done
when the stove is cold.
Troubleshooting
1. Poor heat output
a. Stove too small for room: Seek advice from a Qualified Heating
Engineer as to (kW) output required for the room size. As a
guideline the volume of the room in cubic feet divided by 500;
e.g. room 15’x15’x8’ would require 3.6kW approx.
b. Chimney and/or flue pipe restricted, room ventilation restricted:
On installation these should have been checked but regular
maintenance is necessary as conditions can change; e.g. soot
build up, birds nesting, masonry fall, dust build up or furniture
blocking vents.
c. Poor quality fuel: Only burn dry seasoned timber, soft woods
have a lower heat output than hard woods per hour. Solid
fuels vary in heat value; check with your coal merchant as to
suitability.
2. Dirty Glass Panel
a. Generally caused by poor fuel quality, see (1c)
b. Use secondary air slide (Airwash) for glass panel
c. Fire burning too low, open air vents on stove to create hot fire;
this may ‘burn’ glass clean.
d. If glass requires cleaning use glass cleaner recommended by
your supplier; only use glass cleaner on cold glass. DO NOT
USE any abrasives or scrapers as these will scratch glass and
increase future tar build up making it harder to clean.
3. Unburnt Fuel in Firebox
Insufficient air reaching fuel. Open primary air slide, this will supply
combustion air to burn fuel fully (unless it has reached a ‘point of
return’). Check if the ash pan is full and empty if required. De-ash
with the riddler to make sure the grate is not blocked and check
for jammed clinker or nails when the fire is out and the stove has
cooled.
4. Smoke and Fumes Entering Room
These are very dangerous and must NOT be tolerated. Open
window and allow fire to burn out. Seek expert advice immediately.
DO NOT USE stove until the problem is solved.
5. Chimney Fire
Identified by loud roaring sounds, dense smoke and sparks emitting
from chimney. Shut down the air supply by closing air vents,
close stove door fully and call fire brigade immediately. Regular
chimney maintenance will prevent chimney fires. Seek advice from
a Qualified Chimney Sweep. Chimneys must be checked annually
and more often when bitumas coal and poor quality smokey fuels
are used.
After Sales Service
Your Dimplex Stove is guaranteed against defects arising from
faulty manufacture for 1 year subject to the following conditions.
Failure to comply with these conditions will invalidate the
gaurantee:
• The receipt must be kept as proof of purchase.
• Your Dimplex stove must be installed by suitably qualified
individual (HETAS Engineer or equivalent) and upon
installation a Certificate of Compliance must be presented.
• The guarantee is 1 year from date of purchase.
• The guarantee does not cover parts that are deemed to be
replacable through normal usage of the stove. These include:
glass panels, rope seals, bottom grate or firebars, ashpan,
firebricks, cast iron liners, riddling lever, baffle plate, log
guard.
• Only genuine Dimplex spare parts should be used. Parts that
may need occasional replacement are: firebricks, ashpan, fire
grate, log guard.
Should you require after sales service or should you need to
purchase any spares, please contact the retailer from whom the
appliance was purchased. Please do not return a faulty product
to us in the first instance as this may result in loss or damage and
delay in providing you with a satisfactory service. Please retain
your receipt as proof of purchase.
Langbrook 5kW (LBK5)
28
16
27
9
10
21
20
15
3
7
2
12
13
14
1
6
4
5
19
18
29
22
30
17
11
8
23
25
24
26
LANGBROOK 5KW STOVE (LBK5) - SPARE PARTS
Item
Description
Part Number
Item
Description
Part Number
1
DOOR
3011102
16
BAFFLE PLATE
3011117
2
DOOR HINGE
3011103
17
ASHPAN
3011118
3
HINGE MOUNT
3011104
18
PRIMARY AIR SLIDE
3011119
4
DOOR HANDLE
3011105
19
PRIMARY AIR HANDLE
3011120
5
HANDLE PIN
3011106
20
AIRWASH
3011121
6
DOOR GLASS
3011107
21
AIRWASH SLIDE
3011122
7
GLASS FIXING BKT
3011108
22
DOOR CATCH
3011123
8
GRATE OUTER
3011109
23
FOOT 2 - FRONT RH
3011124
9
GRATE INNER LH
3011110
24
FOOT 1 - FRONT LH
3011125
10
GRATE INNER RH
3011111
25
FOOT 3 - REAR RH
3011126
11
GRATE BAR
3011112
26
FOOT 4 - REAR LH
3011127
12
CONNECTING ROD
3011113
27
BRICK ACCESSORY
(RH, LH & Rear Brick)"
13
RIDDLE BAR
3011114
28
FLUE CAP
3011129
14
RIDDLE LEVER
3011115
29
HAND TOOL
MF09007
15
LOG BAR
3011116
30
PROTECTIVE MITTEN
MF09036
P A C K 3011128
DIMPLEX
MILLBROOK HOUSE
GRANGE DRIVE
HEDGE END
SOUTHAMPTON
SO30 2DF
TEL: 0845 600 5111
FAX: 01489 773050
WEBSITE: www.dimplex.co.uk
Republic of Ireland Tel: 01 842 4833
[c]A Division of GDC Group Ltd.
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of
GDC Group Ltd.