Acecad DigiMemo 692 User guide

Digitally capture & store everything
you write with ink on ordinary paper.
User Guide
Federal Communications Commission (FCC) Radio
Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
z
Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
z
Consult the dealer or an experienced radio/TV technician for help.
The user should not modify or change this device without written approval from ACE
CAD Enterprise Co., Ltd. Modification could void authority to use this equipment.
Trademark Information
ACECAD and ACECAT are registered trademarks of ACE CAD Enterprise Co., Ltd.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
SanDisk is a registered trademark of SanDisk Corporation.
Pentium is a registered trademark of Intel Corporation.
Internet is a trademark of Digital Equipment Corporation.
Adobe and Acrobat are registered trademarks of Adobe Systems Inc.
All other trademarks are the property of their respective owners.
Copyright Notice
©2006 ACE CAD Enterprise Co., Ltd. All rights reserved. No part of this publication may
be reproduced, stored in a retrieval system, or transmitted, in any form or by any means
(electronic, mechanical, photocopying, recording, or otherwise), without the prior written
permission of the publisher.
i
GETTING STARTED....................................................................................................1
EQUIPMENT CHECKLIST ...............................................................................................1
THE PARTS OF THE DIGITAL PAD ..................................................................................2
INSTALLING THE BATTERIES INTO THE DIGITAL PAD ....................................................3
INSTALLING THE BATTERY INTO THE DIGITAL INKING PEN ...........................................3
PUTTING A NOTEPAD OR PAPER ON THE DIGITAL PAD...................................................4
THE WRITING AREA AND THICKNESS ...........................................................................4
STORAGE DEVICE IN THE DIGITAL PAD ........................................................................5
WRITING AND RECORDING YOUR HANDWRITTEN NOTES .........................6
TURNING ON THE DIGITAL PAD ....................................................................................6
CHANGING THE CURRENT DIGITAL PAGE .....................................................................7
THE PEN ICON ..............................................................................................................7
WRITING YOUR NOTES ON A NEW PAGE ......................................................................7
WRITING YOUR NOTES ON A PAGE ALREADY WITH CONTENTS ....................................8
ERASING A DIGITAL PAGE ON THE DIGITAL PAD ...........................................................8
TURNING OFF THE DIGITAL PAD ...................................................................................9
SETTING THE DATE AND TIME ......................................................................................9
LOW BATTERY INDICATION ON THE DIGITAL PAD .......................................................10
NOTES ON REPLACEMENT OF BATTERIES IN THE PAD .................................................10
NOTES ON USE OF THE SD MEMORY CARD ................................................................10
FULL MEMORY INDICATION .......................................................................................10
ORGANIZING YOUR NOTES IN WINDOWS .......................................................11
INSTALLING THE DIGIMEMO MANAGER SOFTWARE ...................................................11
CONNECTING THE DIGITAL PAD TO YOUR COMPUTER................................................13
CREATING YOUR E-BOOK FILE ..................................................................................13
Toolbars................................................................................................................13
Importing Your Digital Pages...............................................................................14
Saving an e-Book File ..........................................................................................16
Saving a Copy of an e-Book File ..........................................................................16
Opening an e-Book File........................................................................................16
Creating a New e-Book File .................................................................................16
Printing an e-Book file .........................................................................................17
EDITING YOUR E-BOOK FILE .....................................................................................17
Zooming in and Zooming out ...............................................................................17
Inserting a Text Box..............................................................................................17
Editing an Existing Text Box.................................................................................17
Drawing a Freeform Line and Writing .................................................................18
Drawing a Straight Line .......................................................................................18
Drawing a Highlighting and Freeform Line.........................................................18
Drawing a Highlighting and Straight Line...........................................................18
Erasing Objects ....................................................................................................18
Undoing the Last Action.......................................................................................18
ii
Selecting Objects.................................................................................................. 19
Resizing Objects................................................................................................... 19
Moving Objects .................................................................................................... 19
Deleting Objects .................................................................................................. 19
Copying or Moving Objects ................................................................................. 20
Changing the Color and Width of Objects ........................................................... 20
Adding a New Page.............................................................................................. 21
Setting the Default New Page Size....................................................................... 21
Moving the Current Page..................................................................................... 21
Removing the Current Page ................................................................................. 21
Showing the Background of Pages....................................................................... 22
Switching the Current Page by Keyboard Shortcuts ............................................ 22
Saving the Current Page as an Image File .......................................................... 22
Sample of an Edited e-Book File.......................................................................... 23
ON-LINE WRITING YOUR NOTES ............................................................................... 23
Causes of the On-line Writing Function Disabled or Closed............................... 25
SENDING YOUR E-BOOK FILE IN E-MAIL ................................................................... 25
CONVERTING YOUR HANDWRITTEN NOTES IN YOUR E-BOOK FILE .......................... 27
USING ANOTHER OPTIONAL CARD READER .............................................................. 27
EASILY MANAGING DIGITAL PAGE FILES ................................................................... 27
Deleting the Digital Pages in the DigiMemo Manager ....................................... 28
TABLET DEVICE IN WINDOWS............................................................................ 30
APPENDIXES ............................................................................................................. 31
REPLACING THE CARTRIDGE OF THE DIGITAL PEN..................................................... 31
Purchasing New Replacement Ink Cartridges ..................................................... 31
REPLACING THE BATTERY IN THE DIGITAL PEN ......................................................... 32
REMOVING THE DIGIMEMO MANAGER SOFTWARE IN WINDOWS .............................. 32
CARING FOR THE DIGIMEMO ..................................................................................... 32
ERROR CODES ON THE DISPLAY OF THE DIGITAL PAD ................................................ 33
The Malfunction of the Built-in 32 MB Storage Device — the Error Code E04 .. 33
The File System Incompatibility of an Optional SD Memory Card — the Error
Code E02 ............................................................................................................. 34
The Damage or Incompatibility of an Optional SD Memory Card — the Error
Code E01 ............................................................................................................. 34
The Full Root Directory — the Error Code E06 .................................................. 34
The Damage of the Digital Pad — the Error Code E03 or E05 .......................... 35
TROUBLESHOOTING ................................................................................................... 35
General Problems ................................................................................................ 35
Problems in the DigiMemo Manager Software.................................................... 37
Problems When Connecting the Digital Pad to your Computer .......................... 38
SPECIFICATIONS ......................................................................................................... 39
Digital Pad Specifications of DigiMemo L2 Model ............................................. 39
Digital Pad Specifications of DigiMemo A402 Model......................................... 39
iii
General Digital Pad Specifications......................................................................39
Digital Pen Specifications ....................................................................................40
File Formats.........................................................................................................40
System Requirements ............................................................................................40
Environment .........................................................................................................40
iv
Getting Started
The DigiMemo is a stand-alone device with storage capability that digitally
captures and stores everything you write or draw with ink on ordinary paper,
without the use of computer and special paper. Then you can easily view, edit,
organize and share your handwritten notes in Windows.
When connected to a PC, the DigiMemo offers an on-line writing function which
can instantly synchronize your writing on the paper with the digital page in its
software in Windows. It also is a USB tablet device in Windows.
Equipment Checklist
The following items are included in your DigiMemo package:
z
z
Digital Inking Pen
(DigiPen P100)
Portable Digital Pad
z
Notepad (already held on the digital pad)
z
Two Replacement Ink Cartridges (already stored in the digital pad)
z
One Plastic Pen Tip (already stored in the digital pad)
z
USB Cable
z
Four Batteries (1.5 volt, size AAA)
z
One 1.55V Button Cell Battery
z
User Guide
z
DigiMemo Manager Software CD
1
The Parts of the Digital Pad
USB Connector
Display
Pen Holder
SD Card
Insertion Slot
Power Button
Notepad Clip
Four Function
Buttons
Notepad Holder
LED
Battery Compartment
Cover
Battery Compartment
Cartridge
Compartment
Two Replacement
Ink Cartridges and
One Plastic Pen Tip
2
Cartridge
Compartment Cover
Installing the Batteries into the Digital Pad
Open the battery compartment cover of
the digital pad. Insert four batteries (1.5
volt, size AAA) into the battery
compartment in accordance with the
indication in the battery compartment.
Close the battery compartment cover.
Note!
Incorrect battery installation may
damage the digital pad.
Note!
Do not mix new and used batteries.
Note!
With continuous use of the digital pad, four AAA alkaline batteries will
last approximately 80 hours.
Installing the Battery into the Digital Inking Pen
Unscrew the barrel cover counterclockwise from the
barrel of the pen. Take out the button cell battery
(SR626SW, 377 or IEC-SR66) that is included in the
package of the DigiMemo. Insert the battery into the
battery compartment with the negative (-) cap facing the
battery compartment. Screw the barrel cover clockwise
onto the barrel until tight.
Pen Clip
Pen Cap
Front Section
Ink Cartridge
(+) Can
(-) Cap
Battery
Compartment
Barrel
Barrel Cover
Rear Section
Note!
Incorrect battery installation will result in the malfunction of the digital
inking pen.
Note!
The battery of the digital inking pen will last approximately 14 months.
Note!
The front or rear section of the pen can hold the pen cap.
Note!
You can attach some cord or accessory to the pen
through the two holes on the pen end.
Pen End
3
Note!
You can clip the pen to the pad by using the pen clip to clip to the right
or left pen holder on the notepad clip.
Two Holes
Note!
You can attach some cord or accessory such as the pen to the pad
through the two holes on the upper-right corner of the pad.
Putting a Notepad or Paper on the Digital Pad
You can use the notepad clip to hold a notepad in the notepad holder on the
pad. You also can directly put a few sheets of paper on the writing area of the
pad for your writing.
The Writing Area and Thickness
The writing area is the area on the
digital pad where the digital pad can
digitally capture and store everything
you write with the digital inking pen as
digital ink. The writing area is shown as
the white area in the illustration. The
carving lines on the pad are the margin
indicators which indicate the upper
boundary of the writing area.
Note!
Writing
Area
Your handwriting on paper
outside the writing area can not
be digitally captured and stored
by the digital pad.
The writing thickness is the maximum thickness above the writing area where
the digital pad can digitally capture and store everything you write with the
digital inking pen as digital ink. The writing thickness is 14 mm (0.55") about
140 sheets of paper.
4
Storage Device in the Digital Pad
The digital pad is equipped with a built-in 32 MB storage device to store your
handwritten notes. You also can load an optional Secure Digital (SD) memory
card into the pad to expand the storage capacity of the pad.
To load an optional Secure Digital (SD) memory card, insert the memory card
all the way into insertion slot until it clicks by holding the memory card with the
terminal side facing upward.
SD Card
Insertion Slot
Terminal Side
Clipped Edge
Note!
The optional memory card must be Secure Digital (SD) memory card
with the file system FAT.
Note!
To remove the Secure Digital (SD) memory card, push the memory
card to pop it out.
Note!
Some brands of memory cards may not be compatible with this digital
pad. Before purchasing a memory card, consult its manufacturer or
dealer. Along with the digital pad, we recommend you to use Secure
Digital (SD) memory cards (32 MB to 2 GB) of the brand SanDisk.
5
Writing and Recording Your Handwritten
Notes
Using the digital inking pen on the digital pad produces both familiar ink notes
on ordinary paper and digital pages in the storage device of the pad.
Note!
The DigiMemo is a stand-alone device. You do not need to connect the
digital pad to your computer for this function.
Turning on the Digital Pad
Press and hold the Power button on the digital pad until the
icon appears on the display. Release the Power button to
turn on the pad. The display will be on and show the Digital Page
Number, Page icon, Storage Device icon, Time display and Battery
icon.
Note!
z
The digital pad can not be turned on when connected to a
PC.
Storage Device Icon
Without loading an optional SD memory card, the Storage Device icon
is displayed and the built-in 32 MB storage device is the current storage
device. Your handwritten notes will be stored in the built-in 32 MB storage
device.
With loading an optional SD memory card, the Storage Device icon
is
displayed and the optional SD memory card is the current storage device.
Your handwritten notes will be stored in the optional SD memory card.
z
Digital Page Number
The Digital Page Number indicates the current digital page in
the current storage device. Your handwriting will be captured
and stored in the current digital page in the current storage
device (the built-in 32 MB storage device or the optional SD memory card).
The digital pad can manage up to 999 digital pages for each storage device
(the built-in 32 MB storage device or the optional SD memory card).
z
Page Icon
The Blank Page icon indicates that the current digital page contains
no digital ink.
The Page with Contents icon indicates that the current digital page
contains digital ink.
6
z
Battery Icon
The Battery icon indicates the battery strength in the digital pad.
Changing the Current Digital Page
You can use the following function buttons on the pad to change the current
digital page in the current storage device.
z
Page Backward Button
to move to the previous digital page.
Press the Page Backward button
By pressing and holding the Page Backward button , the Digital Page
Number moves fast and backward. Once release the button , it stops
moving.
z
Page Forward Button
to move to the next digital page. By
Press the Page Forward button
, the Digital Page
pressing and holding the Page Forward button
Number moves fast and forward. Once release the button , it stops
moving.
z
Next Blank Page Button
Press the Next Blank Page button
page.
to move to the next blank digital
The Pen Icon
When you are writing or drawing on paper by using the digital pen on the
digital pad, the Pen icon appears on the display. The Pen icon indicates
that the digital pad is capturing and storing your handwriting as digital
ink.
Note!
If you do not see the Pen icon while writing, try to alter the pressure you
apply on the pen tip.
Writing Your Notes on a New Page
By using the ,
or
function button, select any blank digital page in which
you want to store a new page of your handwritten notes on paper. We
recommend you to put down the same page number on this new page of paper
as the Digital Page Number. It helps you to synchronize your paper notes and
digital pages.
Under the current Digital Page Number displayed, everything you write will be
7
immediately captured and stored in the current digital page file of the current
storage device. The file name of this digital page is PGLT_XXX.DHW for the
model DigiMemo L2, or PGA4_XXX.DHW for the model DigiMemo A402 (the
XXX is the Digital Page Number such as 001).
is displayed, the digital page file is stored
While the Storage Device icon
in the DMEMO-M folder in the built-in 32 MB storage device.
is displayed, the digital page file is stored
While the Storage Device icon
in the DMEMO-S folder in the optional SD memory card.
Note!
To avoid creating a superimposed digital page, make sure that you
select a blank digital page each time you change a page on paper.
Note!
As you will see later, it is quite important to keep your written page
number and the Digital Page Number aligned. For example, you can
know the contents in the digital page from the page number that you
wrote on paper.
Note!
If you frequently alternate the built-in 32 MB storage device and an
optional SD memory card, we recommend you to write the page
number like “Page M24”, “P M24”, “Page SD24”, “P SD24” … etc. It is
more convenient for you to know which storage device the digital page
is stored in.
Note!
The more you write on a digital page, the bigger size of the digital page
file will be.
Writing Your Notes on a Page Already with Contents
Anytime you can switch to the paper page already with the contents and
or
function button to
continue to write your notes. Moreover, use the
move the Digital Page Number to the one same as you wrote on the paper
page. Now, start to write! Through this way, your new handwriting will be
captured and stored in the right digital page.
Erasing a Digital Page on the Digital Pad
Erasing a digital page is similar to tearing off a paper page. By using the
or
function button to move the Digital Page Number to the one which you want
on the pad. The display will show
to erase. Then press the Erase button
message. Press the Erase button
again to erase all contents
stored in the digital page.
Here is a brief recommendation: you may want to tear off the paper page or
simply cross out the page number you wrote on the paper page.
8
Note!
When
message appears, the erase procedure will be
or
to execute other
cancelled if you write or press any button ,
functions. All contents remain intact in the digital page.
Note!
Once a digital page is erased, its original contents can not be
recovered.
Turning off the Digital Pad
Press the Power button to turn off the digital pad. The display will be blank.
If you have not written or pressed any function button within the previous 30
minutes, the digital pad sounds a beep and automatically shuts down. The
display will be blank.
Note!
Since the pad has the automatic shutdown capability, please make sure
that the display is on if you want to write again after a long period of
time.
As you turn on the digital pad, the display will show the last Digital Page
Number at the time it was turned off.
Setting the Date and Time
The dates created and modified for the digital page file are recorded according
to the clock in the digital pad.
1. Turn off the digital pad.
button on the digital pad. Then press the Power
2. Press and hold the
button until the year digits flash on the display.
3. Repeatedly press or hold down the
4. Press the
or
button to set the year.
button. Then the month digits flash.
5. Repeat Step 3 and 4 to set the month, day, hour, minute, second and year
cyclically.
Note!
Only 24-hour format is available.
6. Press the
button during the setting. The date and time adjustment will
be stored. Then the digital pad will be turned on and the current time
appears on the display.
Note!
If you turn off the digital pad during the setting, the date and time
adjustment will be not stored. The clock automatically returns to the
previous setting.
9
Low Battery Indication on the Digital Pad
When the batteries remain too low power and are in need of
replacement, the Low Battery icon will appear on the display. Please
replace the batteries in the pad.
When the batteries are exhausted, the pad sounds 3 beeps. Then the pad is
turned off immediately.
Notes on Replacement of Batteries in the Pad
When you replace the batteries in the pad, if the batteries are not in the battery
compartment over about one minute, the adjusted date and time will be erased.
Please reset the date and time.
Notes on use of the SD Memory Card
z
Before you remove the SD memory card from the pad, please turn off the
pad first. Or some data in the last digital page file may be lost.
z
When a SD memory card with the write-protect switch set to LOCK is
inserted into insertion slot, the pad sounds 2 beeps and the Storage
flashes on the display. If you use the digital inking pen to
Device icon
write on the pad, the pad will beep. You can not use the digital pad under
this situation. Please remove the SD memory card with the write-protect
switch set to LOCK.
Full Memory Indication
The 90% icon will appear to indicate that 90% capacity of the
or
) is used.
current storage device (
The Full icon will be shown if the memory is full in the current
or
). If that is the case, the digital pad can
storage device (
not store your new handwriting. Also, if you still keep writing, the pad sounds 2
beeps.
Note!
Under such circumstances, you need to erase unwanted digital pages if
you want to continue to write.
Note!
In the following chapter, you will find that it is very easy to import, copy,
move and delete the digital pages when connecting the pad to your PC
through USB cable.
10
Organizing Your Notes in Windows
With its DigiMemo Manager software, you can easily view, edit, organize and
share your digital pages in Windows. You can save any digital pages you
arbitrarily select as a book file (e-Book).
Installing the DigiMemo Manager software
1. Turn on your computer and start Windows.
2. Insert the DigiMemo Manager software CD into the CD-ROM drive. The
software installer will automatically launch. If the CD auto-run feature is not
enabled, double-click the Setup icon on the DigiMemo Manager software
CD. Select the Install DigiMemo Manager option in the dialog box.
3. Click Next in the dialog box.
11
4. Click Next in the dialog box.
5. In the dialog box, click Next to start the installation.
6. The DigiMemo Manager software has been successfully installed. Click
Close in the dialog box. Please restart your Windows.
12
Connecting the Digital Pad to Your Computer
Turn on your computer. Take out the USB cable
included in the package. Plug the wide connector
of the cable into an available USB port on your
computer. Connect the other end of the cable to
the USB connector of the digital pad.
USB
Connector
will appear on the
The Connection icon
display of the pad. The LED on the pad will light.
indicates the
The Connection icon
connection between the digital pad and your
computer. When connecting the pad to the computer, please notice the
following:
z
Your Windows will automatically detect the built-in 32 MB storage device
and the optional SD memory card in the pad as removable storage devices.
z
The pad is powered by the computer.
z
The digital pad can not be turned on. At this moment, your handwriting can
not be stored into the digital page file in the storage device of the pad.
z
The pad is a USB tablet device in Windows. Please refer to the chapter —
Tablet Device in Windows.
z
You can store any computer files such as Word files to the built-in 32 MB
storage device and the optional SD memory card.
z
By using the DigiMemo Manager software, you
can easily import and organize your digital pages
as a book file (e-Book). Moreover, if you doubleclick a digital page file, the DigiMemo Manager
software will be opened and it will import the
digital page to a new book file (e-Book).
Digital Page
File Icon
e-Book File
Icon
Creating Your e-Book File
On the Windows desktop, double-click the ACECAD
DigiMemo Manager icon to open the software.
Toolbars
ACECAD
DigiMemo
Manager
Icon
The following toolbars are on the software window:
z
Standard Toolbar
13
z
Tools Toolbar
z
Color Toolbar
z
Width Toolbar
To move a toolbar to the new location, drag the move handle on a docked
toolbar or the title bar on a floating toolbar.
Move
Handle
Move
Handle
Docked Toolbar
Title Bar
Docked
Toolbar
Floating Toolbar
Importing Your Digital Pages
1. Click the Digital Page button
on the Standard toolbar. The
Digital Page dialog box will appear.
2. Select the Import digital pages option button. Click Browse to select a
folder from which you want to import your digital pages. Such folder could
possibly be the DMEMO-M, the DMEMO-S, the DMEMO-C or any folder
14
that contains digital pages.
3. Click OK. The Import Digital Pages dialog box will appear.
4. To select nonadjacent digital pages, click one digital page, and then hold
down the CTRL key and click each additional digital page.
To select adjacent digital pages, click the first digital page in the sequence,
and then hold down the SHIFT key and click the last digital page.
To preview a digital page, select the digital page and click Preview.
5. Click OK. The digital pages you select will be imported to this book file.
Current Page
Current Page
Indicator
Page
Thumbnails
Current Page
Number and Size
Note!
You can click any page thumbnail to quickly switch the current
15
page.
Note!
You can import and insert any digital pages after the current page.
Note!
The current page number indicates the current page of this book file
(e-Book).
Note!
As importing, the original digital page remains intact.
Saving an e-Book File
Click the Save button
on the Standard toolbar.
Note!
If you are saving the e-Book file for the first time, you will be asked to
give it a name.
Note!
The icon of a book file (e-Book) is
. The
extension of a book file (e-Book) is DND.
e-Book File
Icon
Saving a Copy of an e-Book File
On the File menu, click Save As. In the dialog box, enter a new name for the eBook file. Click Save.
Opening an e-Book File
You can use the following methods to open your e-Book file.
z
In the folder of the e-book file, double-click the e-Book file to open
the file in a new software window.
Note!
z
By this way, you can open various e-Book files in different
software windows.
In the software window, click the Open button
on the Standard
toolbar. In the dialog box, select the folder and then the e-Book file.
Click Open.
Note!
If the previous e-Book file is not saved in its software window, you
will be asked to save that e-Book file.
Creating a New e-Book File
You can use the following methods to create a new e-Book file.
z
On the Windows desktop, double-click the ACECAD DigiMemo
Manager icon to create a new and blank e-Book file with a new
page in a new software window.
Note!
16
By this way, you can open various e-Book files in different software
windows.
z
In the folder of a digital page file, double-click the digital page file.
The digital page will be imported to a new e-Book file in a new
software window.
Note!
z
By this way, you can open various e-Book files in different software
windows.
on the Standard
In the software window, click the New button
toolbar. A new and blank e-Book file with a new page will be created
in the software window.
Note!
If the previous e-Book file is not saved in its software window, you
will be asked to save that e-Book file.
Printing an e-Book file
Click the Print button
e-Book file.
on the Standard toolbar. Click Ok to print the
Editing Your e-Book File
Zooming in and Zooming out
You can click the Zoom in button
current page or the Zoom out button
reduced size.
to get a close-up view of the
to see more of the page at a
Inserting a Text Box
1. Click the Text Box button
on the Tools toolbar.
2. Click and drag in the current page where you want to insert the text
box.
3. Type and edit your text in the text box.
Note!
You can click a color button to change the color of the text or
click the Font button
to change the font of text.
Editing an Existing Text Box
1. Click the Select button
on the Tools toolbar.
2. Click anywhere inside the existing text box. Then edit your text.
Note!
You can click a color button to change the color of the text or
to change the font of text.
click the Font button
17
Drawing a Freeform Line and Writing
1. Click the Pen button
on the Tools toolbar.
2. You can switch the color by clicking a color button on the Color
toolbar. You can change the width by clicking a width button on the
Width toolbar.
3. Drag to draw a freeform line or write.
Drawing a Straight Line
1. Click the Line button
on the Tools toolbar.
2. You can switch the color by clicking a color button on the Color
toolbar. You can change the width by clicking a width button on the
Width toolbar.
3. Click and drag to draw a straight line.
Drawing a Highlighting and Freeform Line
1. Click the Highlighter button
on the Tools toolbar.
2. You can switch the color by clicking a color button on the Color
toolbar. You can change the width by clicking a width button on the
Width toolbar.
3. Click and drag to draw a highlighting and freeform line.
Drawing a Highlighting and Straight Line
1. Click the Highlighting Line button
on the Tools toolbar.
2. You can switch the color by clicking a color button on the Color
toolbar. You can change the width by clicking a width button on the
Width toolbar.
3. Click and drag to draw a highlighting and straight line.
Erasing Objects
1. Click the Eraser button
on the Tools toolbar.
2. To erase, drag the pointer over the digital ink strokes or lines.
Undoing the Last Action
Click the Undo button
action you took.
18
on the Standard toolbar to undo the very last
Selecting Objects
You can use the following methods to select objects:
z
To select only one object, click the Select button
and then one
digital ink stroke or line. A Selection box will appear around the
selected object.
z
To select one or several digital ink strokes, lines or text boxes, click
. Then click and drag a box around the whole of
the Select button
them. A Selection box will appear around the selected objects.
z
Click the Select All button
to select all objects in the current
page. A Selection box will appear around the selected objects.
Note!
By clicking the Select button
and then one text box, you can edit
the text in the text box. However you can not select the text box by this
way.
Note!
To select one text box, click the Select button
. Then you must click
and drag a box around the text box. A Selection box will appear around
the selected text box. However you can not edit the text in the text box
by this way.
Resizing Objects
1. Select one or several digital ink strokes, lines or text boxes.
2. Rest the pointer on any corner of the Selection box until the pointer
becomes a double-headed arrow.
3. Drag the corner of the Selection box to change the size of the selected
objects.
Moving Objects
1. Select one or several digital ink strokes, lines or text boxes.
2. Move the pointer into the Selection box. The pointer will then become a
move pointer.
3. Drag the selected objects in the Selection box to a new location.
Deleting Objects
1. Select one or several digital ink strokes, lines or text boxes.
2. Click the Delete button
selected objects.
or press the DELETE key to delete the
19
Copying or Moving Objects
1. Select one or several digital ink strokes, lines or text boxes.
2. Do one of the following:
z
To move the selected objects, click the Cut button
Standard toolbar.
on the
z
To copy the selected objects, click the Copy button
Standard toolbar.
on the
3. Do one of the following:
z
If you want to copy or move the selected objects to another page
in this or another e-Book file, switch to the page. Click the Paste
button
on the Standard toolbar. The Selection box will be
around the pasted objects. You can move the pasted objects to a new
location.
z
If you want to copy or move the selected objects to the same
page, click the Paste button
on the Standard toolbar. The
Selection box will be around the pasted objects. You can move
the pasted objects to a new location.
z
If you want to copy or move the selected objects to another file for other
programs such as Outlook e-mail message, Word file or Excel file,
switch to the file. Click the Paste command in the program.
Changing the Color and Width of Objects
1. Select one or several digital ink strokes or lines.
2. Click a color button on the Color toolbar to switch the color of the selected
objects. Click a width button on the Width toolbar to change the width of
the selected objects.
Note!
20
By selecting a text box, you can not change the color of text in the
text box. By editing a text box, you can click a color button
to change the color of the selected text or click the Font
to change the font of the selected text.
button
Adding a New Page
Click the Add Page button
on the Standard toolbar. A new page
will appear at the end of this book file.
Setting the Default New Page Size
The Default New Page Size is for the new page which you add in the e-Book
file. It does not matter with the page size of the digital page which you import to
the e-Book file.
To set it, click Page Setup on the File menu. The Default New Page Size
dialog box will appear. We recommend that you select the option button in
accordance with your DigiMemo model.
Moving the Current Page
1. On the Page menu, click Move to. The Move to dialog box will appear.
2. In the dialog box, type the page number (such as 5) which you want to
move the current page to.
3. Click OK. The current page will then be moved to the page you designated
previously.
Removing the Current Page
. A dialog box will appear. Click Yes.
Click the Remove Page button
The current page and all its contents will be removed.
21
Showing the Background of Pages
1. On the Edit menu, click Option. A dialog box will appear.
2. Choose or clear the following check boxes to show the background on:
z
Current page
z
Page thumbnails
3. If necessary, select the following one option button:
z
Default background (Lines)
z
Import image as background
Click the Browse button to find the image file such as BMP, JPG, GIF
or PNG file which you want to be the background.
4. Choose or clear the Print background when printing check box.
5. Click OK.
Switching the Current Page by Keyboard Shortcuts
First Page
CTRL+HOME
Last Page
CTRL+END
Previous Page
PAGE UP
Next Page
PAGE DOWN
Saving the Current Page as an Image File
You can save the current page as an image file whose file types can be BMP,
JPG, GIF or PNG.
22
1. Click the Save as Image button
on the Standard toolbar.
2. In the dialog box, select a file type and enter a file name. Click Save.
Sample of an Edited e-Book File
On-line Writing Your Notes
When the digital pad is connected to your computer through a USB port, you
can use the On-line Writing function in the DigiMemo Manager software. By
using the digital pen on the pad, the On-line Writing function can instantly
synchronize your writing on the paper with the current page in the software
window. For example, your writing on the paper in the lower-left corner of the
pad instantly appears in the lower-left corner of the current page in the software
window.
Note!
Before you write or draw by using the On-line Writing function, we
recommend that you already switch to the right paper page on the pad
and switch the right current page in the software window.
23
To use the On-line Writing function, execute the following steps:
1. Make sure that the digital pad is connected to your computer through a
appears on the display of the pad.
USB port. The Connection icon
2. On the Tools toolbar in the software window, click the On-line
to activate the function.
Writing button
Note!
When you activate the On-line Writing function, the tablet
device function in Windows of the pad will be closed. You can not
use the digital pen on the pad to move the mouse pointer on the
screen. When you move the digital pen on the pad, the On-line
Writing cursor moves only inside the current page in the software
window.
Note!
The zoom setting for the current page will be automatically changed
to 100%. You can not change the zoom setting.
Note!
By using your mouse, you still can use the other functions such as
Eraser in the software window.
3. You can switch the color by clicking a color button on the Color toolbar by
using your mouse. You can change the width by clicking a width button on
the Width toolbar by using your mouse.
4. By using the digital pen on the pad, your writing or drawing on the paper
instantly appears on the corresponding position of the current page in the
software window. For example, your writing on the paper in the lower-left
corner of the pad instantly appears in the lower-left corner of the current
page in the software window.
Note!
When you write or draw, the software automatically adjust the
current page position in the active software window so that your
writing or drawing can be instantly visible in the active software
window.
Note!
You can switch both the paper page on the pad and the current
page in the software window.
Note!
Even though the software window is not active, the activated Online Writing function still is available.
Note!
If you close or minimize the software window in which the On-line
Writing function is activated, the On-line Writing function will be
closed.
Note!
Your writing or drawing will not be stored in any digital page file in
the storage device of the pad.
5. To close the On-line Writing function, click the On-line Writing
button
on the Tools toolbar in the software window.
24
Note!
When the On-line Writing function is closed, the tablet device
function in Windows of the pad will be activated. You can use the
digital pen on the horizontal pad to move the mouse pointer on the
screen. Please refer to the chapter — Tablet Device in Windows.
Causes of the On-line Writing Function Disabled or Closed
To use the On-line Writing function, please verify the followings, or the On-line
Writing function will be disabled or closed:
z
The page size of the current page in the software window must be in
accordance with your DigiMemo model.
z
The page size in accordance with the DigiMemo Model is shown below.
DigiMemo Model
DigiMemo L2
DigiMemo A402
Page Size
Letter
A4
Note!
The page size of the current page is shown in the lower-right corner
of the software window.
Note!
The page size of a digital page which you import is in accordance
with the DigiMemo model which created it.
Note!
The page size of a new page which you add in the e-Book file is
according to the Default New Page Size setting. If it is necessary to
change the setting, please refer to the section — Setting the
Default New Page Size.
z
If the On-line Writing function already be activated in one software
window, it will be disabled in other software windows.
z
Make sure that the digital pad is connected to your computer through a
appears on the display of the pad.
USB port. The Connection icon
z
The DigiMemo L2 or A402 supports and can use the On-line Writing
function. Some DigiMemo models such as 692, A501 or A502 do not
support and can not use the On-line Writing function.
Sending Your e-Book File in E-mail
You can use one of the following methods to send your e-Book file in e-mail:
z
In the software window of DigiMemo Manager, you can copy or move
several pages or just part of a page in your e-Book file to your Outlook email message.
25
Note!
z
You can not use this copy or move technique in an Outlook
Express e-mail message.
In an e-mail message, insert your e-Book file as an attachment.
Note!
To view and edit your e-Book file, the recipient must have the
DigiMemo Manager software. If he or she does not have this
software, please download it on the ACECAD website.
http://www.acecad.com.tw/digimemo/download.html
z
Open your e-Book file in the DigiMemo Manager software. Click the
on the Standard toolbar. In the dialog box, select
E-mail button
the Attach your e-Book file option. Click OK. Your e-Book file will
be attached to a new e-mail message.
z
Open your e-Book file in the DigiMemo Manager software. Click the
on the Standard toolbar. In the dialog box, select
E-mail button
the Attach images option. Click OK. Every page of your e-Book file will be
saved as a JPG image file and be attached to a new e-mail message.
26
Converting Your Handwritten Notes in Your e-Book
File
1. If you have installed the optional DigiMemo Handwriting Recognition
software, click the Conversion button
on the Standard toolbar
in the software window of DigiMemo Manager.
2. In the dialog box, select the following one option button:
z
Current Page
In this option, you can choose the Selected area only check box.
z
All Pages
z
Select Pages
You can select several pages by using CTRL or SHIFT key with mouse
click.
3. Click OK. The selected pages or area will be imported into the DigiMemo
Handwriting Recognition software.
Using Another Optional Card Reader
If you have another optional card reader for SD memory card, you can organize
your digital page or other computer files in the optional SD memory card
through this card reader.
Easily Managing Digital Page Files
When connecting the digital pad to your computer, the removable storage
device, such as the built-in 32 MB storage device or the optional memory card
27
of the pad, is accessed to your computer. The following procedures can be
easily executed in your Windows.
z
Delete the digital page files in the built-in 32 MB storage device or the
optional memory card of the digital pad.
Here is a brief recommendation: you may want to tear off the paper page or
simply cross out the page number you wrote on the paper page.
z
Note!
Once a digital page file is deleted in a removable storage device
(the built-in 32 MB storage device or the optional memory card), it
can not be recovered.
Note!
You can not delete files in memory card when the write-protect
switch of the memory card is set to LOCK.
You can copy or move the digital page files in the built-in 32 MB storage
device or the optional memory card to your hard disk drive. You also can
rename the digital page files in your hard disk drive.
Note!
Do not rename the digital page files in the folder DMEMO-M of the
built-in 32 MB storage device or the folder DMEMO-S of the optional
memory card. Otherwise the digital pad can not manage the
renamed digital pages.
Deleting the Digital Pages in the DigiMemo Manager
1. In the software window of DigiMemo Manager, click the Digital
Page button
on the Standard toolbar. The Digital Page dialog
box will appear.
2. Select the Delete digital pages option button. Click Browse to select a
folder in which you want to delete your digital pages. Such folder could
possibly be the DMEMO-M, the DMEMO-S, the DMEMO-C or any folder
that contains digital pages.
3. Click OK. The Delete Digital Pages dialog box will appear.
28
4. To select nonadjacent digital pages, click one digital page, and then hold
down the CTRL key and click each additional digital page.
To select adjacent digital pages, click the first digital page in the sequence,
and then hold down the SHIFT key and click the last digital page.
To preview a digital page, select the digital page and click Preview.
5. Click OK. The digital pages you select will be deleted.
29
Tablet Device in Windows
When the digital pad is connected to your computer through a USB port, the
will appear on the display of the pad and the LED on the
Connection icon
pad will light. The digital pad is a tablet device in Windows and for all Windows
applications. You can use the digital pen on the horizontal writing area of the
pad to move the mouse pointer on the screen. The pen tip of the digital pen is
the primary button of the mouse.
The horizontal writing area of the pad corresponds directly to the whole screen.
For example, if you move the pen to the lower-left corner of the horizontal
writing area, the mouse pointer will move to the lower-left corner of the screen.
Horizontal
W
Note!
If you put a notepad or paper on the pad for use with a drawing program
such as Painter, we recommend that you use the ink cartridge in the
digital pen. If you move the digital pen directly on the plastic surface of
the writing area, we recommend that you use the plastic pen tip in the
digital pen. Please refer to the section in the Appendixes — Replacing
the Cartridge of the Digital Pen.
Note!
When you activate the On-line Writing function in the DigiMemo
Manager software, the tablet device function in Windows of the pad will
be closed. You can not use the digital pen on the pad to move the
mouse pointer on the screen. When you move the digital pen on the
pad, the On-line Writing cursor moves only inside the current page in
the software window.
30
Appendixes
Replacing the Cartridge of the Digital Pen
Open the cartridge compartment cover on the back of the digital pad. Two
replacement ink cartridges and one plastic pen tip are stored in the cartridge
compartment of the digital pad.
Clip Hole
To replace the cartridge of the pen, you may use a small clip to gently pull the
old one out. Then insert a new one and press the cartridge tip firmly against a
hard surface until it snaps into place.
You can also use the clip hole in the cartridge
compartment to replace the cartridge.
1. Hold the digital pen upright and insert the cartridge tip
into the wider side of the clip hole.
2. Gently push the pen horizontally towards the narrow
side of the clip hole to as far as it can reach.
3
1
3. Gently pull out the cartridge from the pen.
4. Insert a new one. Then press the cartridge tip firmly
against a hard surface until it snaps into place.
2
Purchasing New Replacement Ink Cartridges
The specification of ink cartridge used for the digital pen is 2.3 mm/0.09"
(Diameter) x 67 mm/2.64" (Length).
Note!
The material of some ink cartridges may affect the performance of the
digital pen. Some ink cartridge with the different outside dimensions
may damage the digital pen.
Note!
The following ink cartridges have been tested and approved for use with
31
the digital pen:
Brand
Model
ACECAD
Ink Cartridge Series
Cross
8518-1
Zebra
BR-8A-4C
Lamy
M21
Sterling (Target)
01800T
SPALDING
RFR80A
STAEDTLER
930-ASBK3V
Replacing the Battery in the Digital Pen
Even though the battery of the digital pen can last approximately 14 months,
the battery in the pen may be exhausted if any of the following situations
occurs. If so, please replace the battery.
z
Severe missing digital ink strokes
z
Serious lengthened or shortened digital ink strokes
z
Significant twisted digital ink strokes
z
Decreasing of the writing thickness
Removing the DigiMemo Manager Software in
Windows
Open Add or Remove Programs icon in the Control Panel window. Remove
the ACECAD DigiMemo Manager software.
Caring for the DigiMemo
To assure proper functioning of the digital pen and pad, please observe the
following precautions:
z
Remove the batteries from the digital pad if it is not expected to be used for
long periods. This will eliminate the possibility of battery liquid leaking from
the batteries and corroding the digital pad.
z
Remove the button-cell battery from the digital inking pen if it is not
expected to be used for long periods. This will eliminate the possibility of
32
battery liquid leaking from the batteries and corroding the digital pen.
z
Avoid placing diskettes or other magnetic media on the pad surface.
z
Avoid placing hot or heavy items on the pad.
z
Clean the pen and pad with a soft cloth lightly dampened with water or a
neutral detergent.
z
Never drop the pen or pad. The pen or pad may malfunction if subjected to
strong shocks or vibration.
z
Avoid cutting or scratching the pad surface.
z
Never immerse the pen and pad in liquid.
z
Avoid operating or storing the pen and pad in extremely hot or cold
temperatures, or where the relative humidity is high.
z
Never take the pad or pen apart.
z
Do not use or store the product in the vicinity of equipment that generates
strong electromagnetic radiation or magnetic fields.
Error Codes on the Display of the Digital Pad
The Malfunction of the Built-in 32 MB Storage Device — the
Error Code E04
If any of the following situations occurs, you need to reset the built-in 32 MB
storage device in the digital pad.
z
The malfunction of the built-in 32 MB storage device occurs.
z
The error code E04 appears on the display of the pad. It indicates that the
file system of the built-in 32 MB storage device is incompatible with the pad.
Note!
Resetting the built-in 32 MB storage device permanently deletes all data
and files it contains.
To reset the built-in 32 MB storage device, execute the following steps:
Note!
If a SD memory card is loaded in the digital pad, we recommend that
you remove the SD memory card from the pad.
1. While the digital pad is turned off, press and hold the Erase button
the pad.
on
2. Meanwhile, press and hold the Power button on the pad until the
icon appears on the display.
3. Release the Power button while continuing holding down the Erase button
.
33
4. Then release the Erase button
.
5. When the reset is finished, the digital pad will be turned on.
Note!
Note!
The display will show the current digital page 001 with no digital ink
in the built-in 32 MB storage device if no SD memory card is loaded
in the pad.
Do not format the built-in 32 MB storage device through the format
function in Windows. Or it will cause the incompatibility problem with the
pad.
The File System Incompatibility of an Optional SD Memory
Card — the Error Code E02
If the error code E02 appears on the display of the digital pad, it indicates that
the file system of the optional SD memory card is incompatible with the digital
pad. If you want the digital pad to capture and store your handwriting in this
optional SD memory card, please format this memory card before use.
Note!
Formatting an optional memory card permanently deletes all data and
files it contains. Before formatting, be sure to transfer to a computer any
files you would like to keep.
To format an optional SD memory card, execute the following steps:
1. Load the memory card into the digital pad.
2. Turn on your computer and start Windows.
3. Connect the digital pad to your computer.
4. Format the memory card with the file system FAT in Windows.
Note!
The digital pad only supports an optional SD memory card with the file
system FAT. The digital pad does not support an optional SD memory
card with other file system.
The Damage or Incompatibility of an Optional SD Memory
Card — the Error Code E01
If the error code E01 appears on the display of the digital pad, it indicates that
the optional memory card may be damaged or the memory in the memory card
is incompatible with the digital pad. You can not use it with the pad.
The Full Root Directory — the Error Code E06
If the error code E06 appears on the display of the digital pad, it indicates that
too many files or folders in the root directory in the built-in 32 MB storage
device or the optional SD memory card. Move or delete some files or folders in
34
the root directory.
The Damage of the Digital Pad — the Error Code E03 or E05
If the error code E03 or E05 appears on the display of the digital pad, it
indicates that the digital pad may be damaged. It needs to be repaired. Please
contact the ACECAD distributor.
Troubleshooting
General Problems
Problem: A superimposed digital page is created.
Solution: Make sure to select a blank digital page each time you change a
page on paper.
Problem: Minor lengthened or shortened digital ink strokes occur
Solution: Write a little bit slowly or harder.
Problem: Significant missing, twisted, lengthened or shortened digital ink
strokes occur.
Solution: Please check the following situations for the digital pen:
z
The battery is correctly installed in the pen.
z
The battery must be inserted into the battery compartment with
the negative (-) cap facing the battery compartment.
z
The cushion (copper color) of
the battery is still located inside
the barrel cover. In fact, such
cushion will remain at its original
position unless it is improperly
removed.
Barrel Cover
z
The barrel cover is screwed tightly onto the barrel of the pen.
z
Once the battery inside the digital pen has been used for a long
time, it should be replaced with a new one.
z
If you just replace an ink cartridge of the pen, please press the
new cartridge tip firmly against a hard surface until it snaps into
place.
Please verify that the thickness of paper is under the writing
35
thickness of the digital pad.
Solution: Do not try to trace or write through any conductive material (for
example: steel ruler).
Problem: When you are writing or drawing on paper by using the digital pen on
the digital pad, the Pen icon does not appear on the display.
Solution: Try to alter the pressure you apply on the pen tip.
Problem: After replacing the ink cartridge with the new one, the performance
level of the digital pen is lowered.
Solution: Please purchase and use an ink cartridge which we recommend.
Problem: The digital pad can not be turned on.
Solution: Please verify that the digital pad is not connected to your computer.
Problem: After using for a period of time, you can not turn on the digital pad.
Solution: The batteries in the pad may be exhausted. Please replace the
batteries.
Problem: After replacing the batteries of the digital pad, the date and time in
the pad are incorrect.
Solution: When you replace the batteries in the pad, no battery in the battery
compartment may be over one minute. The adjusted time and date
are erased. Please reset the date and time.
Problem: After you load an optional SD memory card into the digital pad and
then turn on the pad, the Storage Device icon
is not shown on
.
the display. The display still shows the Storage Device icon
Solution: Make sure that you insert the memory card correctly into the SD card
insertion slot of the pad.
Problem: The Storage Device icon
flashes on the display.
Solution: When a SD memory card with the write-protect switch set to LOCK is
inserted into insertion slot, the pad sounds 2 beeps and the Storage
Device icon
flashes on the display. Please remove the SD
memory card with the write-protect switch set to LOCK.
36
Problem: Even though the stored digital pages have not reached 999, the
memory (either in the built-in 32 MB storage device or in an optional
memory card) is full.
Solution: Although the digital pad has the ability to manage up to 999 digital
pages (either for the built-in 32 MB storage device or for an optional
memory card), such ability is unrelated to the maximum storage
capacity.
The full memory means that the used space for the digital page files
and the other computer files reaches the maximum capacity of the
built-in 32 MB storage device or an optional memory card.
Problem: When pressing the Next Blank Page button , the current digital
page does not move to the next blank digital page and the pad
sounds 2 beeps.
Solution: In the DMEMO-M or DMEMO-S folder in the current storage device
(the built-in 32 MB storage device or the optional memory card),
there are already 999 digital page files containing digital ink. Move or
delete some digital page files in the folder.
Problems in the DigiMemo Manager Software
Problem: When you switch to a new current page in the software window, the
activated On-line Writing function is closed.
Solution: The page size of the new current page should be not in accordance
with your DigiMemo model. Please refer to the section — Causes of
the On-line Writing Function Disabled or Closed.
Problem: In the software window of DigiMemo Manager, the selected objects in
an e-Book file can not be copied or moved to a file for some
programs such as Notepad.
Solution: You can copy or move the selected objects to another file for other
programs such as Outlook e-mail message, Word file or Excel file.
However, this function is not suitable for all Windows programs.
Problem: Problems occur on the printing results.
Solution: We recommend you to use the Letter, A4 or A5 paper size.
37
Problems When Connecting the Digital Pad to your Computer
Problem: When connecting the digital pad to your computer through a USB
port, your Windows can not recognize the built-in 32 MB storage
device and an optional memory card in the pad as removable storage
devices.
Solution: Please verify the followings:
z
The USB port is available.
z
Make sure that a power adapter provides enough power to the
USB hub while connecting the digital pad via an USB hub.
z
We recommend you connect the digital pad directly to an USB
port on the computer.
z
Occasionally, if your Windows can not recognize them, please
restart your Windows.
Problem: Before disconnecting the digital pad from your computer, what should
be noticed?
Solution: The following stated notice is applied for all removable storage
devices. Close any associated windows for the built-in 32 MB storage
device or an optional CF memory card before attempting to
disconnect the digital pad from your computer.
38
Specifications
Digital Pad Specifications of DigiMemo L2 Model
Size
9.88" (width) x 13.22" (length)
251 mm (width) x 336 mm (length)
Thickness
0.47" (12 mm)
Weight
Approx. 1.4 lbs (635 g) without batteries
Approx. 1.5 lbs (680 g) with batteries
Writing Area
8.5" x 11" (216 mm x 279 mm)
Writing Thickness
0.55" (14 mm); approx. 140 sheets of paper
Notepad Holder
Holder for Letter size notepad;
8.5" x 11.9" (216 mm x 302 mm)
Digital Page Size
Letter size (8.5" x 11" / 216 mm x 279 mm)
Digital Pad Specifications of DigiMemo A402 Model
Size
245 mm (width) x 336 mm (length)
9.63" (width) x 13.22" (length)
Thickness
12 mm (0.47")
Weight
Approx. 615 g (1.35 lbs) without batteries
Approx. 660 g (1.45 lbs) with batteries
Writing Area
210 mm x279 mm (8.27" x 11")
Writing Thickness
14 mm (0.55"); approx. 140 sheets of paper
Notepad Holder
Holder for A4 size notepad;
210 mm x 300 mm (8.27" x 11.81")
Digital Page Size
A4 size (210 mm x 297mm / 8.27" x 11.7")
General Digital Pad Specifications
Storage Medium
Built-in 32 MB storage device
Optional Storage
Medium
Secure Digital (SD) memory card
(FAT file system)
Power Source
Four (4) batteries (1.5volt, size AAA)
Power Voltage: 3V
Power Current: Approx. 25 mA
Power Consumption: Approx. 75 mW
Battery Life
Approx. 80 hours
39
Power Source
Supplied from USB port when connecting the digital
pad to PC.
Interface to PC
USB port
Digital Pen Specifications
Size
134 mm (length) x 11.3 mm (diameter)
5.28" (length) x 0.45" (diameter)
Weight
13.8 g (0.03 lbs) with battery
Power Source
One (1) 1.55V button cell battery
(SR626SW, 377 or IEC-SR66)
Battery Life
Approx. 14 months
Ink Cartridge
2.3 mm (diameter) x 67 mm (length)
0.09" (diameter) x 2.64" (length)
File Formats
Digital Page
ACECAD digital page file format (DHW)
e-Book File
ACECAD e-Book file format (DND)
System Requirements
Operating System
Windows 2000 or XP
CPU
500 MHz Pentium III or better
RAM
128 MB or more recommended
Equipment
Available USB port
CD-ROM drive
Hard Disk Space
32 MB
Environment
Operating Temperature
0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity
Less than 85% (no condensation)
Storage Temperature
-20 °C to 60 °C (-4 °F to 140 °F)
Note!
40
These specifications are subject to change without notice.
www.acecad.com.tw
Part Number: 91100-40590
English Version v1.0
Printed in China 2006.09