Washing Machine
WAF 6150 A - WAF 6140 A
WAF 6120 A - WAF 6100 A
WAF 6080 A
User's Manual
Downloaded From WashingMachine-Manual.com Manuals
Contents
1- Technical Features of Your Washing Machine
3
2- Warning
5
3- Preparation
7
4- Program Selection and Starting Machine
11
5- Care and maintenance
15
6- Installation
17
7- Before calling service
19
Downloaded From WashingMachine-Manual.com Manuals
2
Depth (cm.)
Net Weight (kg.)
Electricity (V/Hz.)
Total Current (A)
Total Power (W)
Washing -rinsing cycle
(cyc/min)
Spinning cycle (max
cyc/min)
WA 6080 A
Width (cm.)
WA 6100 A
Height (cm.)
WA 6120 A
Maximum dry laundry
capacity (kg.)
WA 6140 A
Technical Features of Your Washing Machine
WA 6150 A
1
6
6
6
6
6
85
60
54
71
230/50
10
2350
85
60
54
71
230/50
10
2350
85
60
54
71
230/50
10
2350
85
60
54
71
230/50
10
2350
85
60
54
71
230/50
10
2350
52
52
52
52
52
1500
1400
1200
1000
800
There may be changes in the technical
features without prior notice in order to
enhance product quality.
The figures in the manual are schematic
and may not represent your actual machine one-to-one.
Labelling on your product and ones
declared in the documents accompanying product are the values obtained under
laboratory conditions with given standards. These values may vary according to
usage and environmental conditions.
Downloaded From WashingMachine-Manual.com Manuals
3
Your Washing Machine
1
2
3
4
5
1 Detergent dispenser
2 Front Panel
3 Front door
4 Kick Plate Cover
5 Height-adjustable feet
Downloaded From WashingMachine-Manual.com Manuals
4
2
Warning
• This product is designed for home
use.
of water and hygiene compound
used. If low quality and unfitting
cleaning material is used the
stains will be fixed. Before washing your laundry with stain keep
your attention on cleaning the
laundry as explained in following
pages.
• Your washing machine is adjusted
to 230V.
• If the fuse in your house is less
than 16A than have a certified
electrician deploy an 16A fuse.
• In case of transformer or nontransformer use, grounding installation must be performed with a licensed electrician. Any use before
grounding is not our responsibility.
• This is period of keeping spare
parts for your machine to operate.
Because of quality control procedures there might be little amount
of water in your machine. This
does not have any damage to your
machine.
• In order to make your machine
ready call Authorized Service,
prepare clean tap water and water
draining with licensed plumber.
• Your machine is programmed for
starting operation again when
electricity is off and on afterwards.
You can not press On / Off button
to cancel program. Machine will
go on program when electricity is
on. To CANCEL the program press
>Start/Pause/Cancel< button for
three seconds. (See. Cancelling a
program)
• Never place your machine over a
carpet covered floor. Otherwise
electrical parts of your machine
may overheat. This may cause
malfunction of your machine.
• Make sure hot and cold taps are
connected correctly. Otherwise
your laundry may come out hot
and torn .
• Please call certified service for a
failure of electric plug / cable.
• Be careful about your water hoses
are not old. Do not use old / torn
water hoses. This may cause stain
in your laundry .
•
• At first use, washing must be
performed at Cotton 90°C program
without loading with laundry for
getting your machine ready for
washing.
•
• Performance of your washing
machine depends on the quality
If “Door” led on program progress
display is blinking program selection knob is middle position. In this
case turn the knob and adjust it
again. If the warning continues call
authorized service.
After your machine starts operation, if Start/Pause/Cancel key
starts blinking than door is not
locked. Open and close the door
again begin washing program
again.
If the “washing” led on the program progress display is blinking
either there is no water or tap is
Downloaded From WashingMachine-Manual.com Manuals
5
•
•
off. Check your taps. Turn your
machine off and on. If the problem
persists unplug your machine, turn
off tap water and call authorized
service.
If program is started and program
selection can not be performed
your machine might be in protection mode due to infrastructure
problem (voltage, water pressure,
etc.) Press and hold the > Start/
Pause/Cancel < button for 3 seconds in order to switch machine to
factory settings.
Most of the warnings resulting in
calling an authorized service are
due to infrastructure problems. For
this reason applying to an Authorized Service is recommended.
Downloaded From WashingMachine-Manual.com Manuals
6
3
Preparation
Before starting your machine
please beware of below mentioned points:
Opening front door
Pull the handle to open the front door.
Your machine’s front door is designed
for opening during only machine
is not operating. If the led displays
“door” than door can open.
Did you plug the cable?
Did you connect draining hose correctly?
Did you close front door?
Did you open tap water?
Loading machine with laundry
Fill the machine by unfolding and
not squeezing laundry. Place handwoven garments inside-out to the
machine. Make sure there is no
laundry jammed between bellow and
front-door.
Close the loading door by pushing.
If loading door is not properly closed
machine will not start.
If you haven’t installed your machine please read to “Installation”
section.
Sorting the Laundry
Sort laundry according to type of
fabric, color, level of dirtiness and
allowed washing temperature. Do
not wash white laundry together with
colored ones. Remove hard parts like
belt, wrist button, curtain buttons, etc.
or place laundry in a cloth bag. Empty
pockets. Zip up and button up. Very
tiny laundry like baby clothes may get
into inside of drum, midst of bellow,
pump filter, hose, etc. in order to prevent this it is advised to place such
laundry in a special laundry string bag
or large laundry. See practical and
useful information section for soiled
laundry. Your machine can wash “Machine Wash” or “No-matting” labeled
woolen with special woolen program.
Delicate laundry with “Do not wash”
or “hand wash” label (silk, cashmere,
pure wool, etc.) can be washed in the
special hand-wash program.
Selection of detergent and
softener
Quantity of the detergent used
depends on hardness of water and
how soiled laundry is. Recommended
values are indicated on the package.
If your laundry is low soiled and/or
hardness of water is low use less detergent as indicated on the package.
Otherwise it may result in excessive
foam.
You should use detergent specially
designed for automatic washing
machines. Avoid using bleach product
containing sulfur or chlorine. Place
powder detergent and softener in
appropriate drawer compartment and
close detergent dispenser.
Downloaded From WashingMachine-Manual.com Manuals
7
a. Compartment I, powder detergent
drawer for pre-wash.
b. Compartment II, powder detergent
drawer for main wash.
c. Softener dispenser
d. Siphon
Fill the softener as indicated (usually <100ml; 1 tea bag) on package. Never fill more than “MAX”
level. Excess amount will drain to
suction cup and be wasted. You
might need to fill softener again.
If softener is thickened over time
add some water for thinning.
Softener may obstruct siphon and
block flow.
Downloaded From WashingMachine-Manual.com Manuals
8
Control Panel
1
2
6
3
5
1- Program selection knob
2- Time delay selection button
3- Auxiliary function buttons
4- On / Off button
5- Program progress display
6- Spin speed selection knob
Downloaded From WashingMachine-Manual.com Manuals
9
4
Auxiliary Functions
Quick-wash
Shortens washing time for lightly
soiled fabrics.
Rinse plus
By using this function your machine
will add another rinse process to the
three rinse processes that it has already done. This additional rinse will
reduce any affects on sensitive skin
by washing leftover detergent.
Anti-creasing
To avoid wrinkling of your clothes,
select this function. When Easy-iron
is chosen please load less cloth, this
way a special washing and spinning
profile will reduce the wrinkles and
your clothes will be easy to iron.
Spin speed selection knob
You can spin the laundry up to 1500
cycle / min.(depending on model)
with the models having cycle selection button. Your machine will spin not
more than 800 cycle / min. for synthetic programs and 600-400 cycle/
min. for woollen programs.
In addition if you do not want to spin
your laundry you may choose “No
Spin” position.
Downloaded From WashingMachine-Manual.com Manuals
10
4
Program Selection and Starting Machine
Plug you machine to outlet. Turn on
the machine by pressing “On / Off”
key. Open the door by pulling the
handle and load the machine without
exceeding loading capacity and close
the door. Specify the appropriate program by looking at program selection
table according to type of laundry,
degree of soiledness and washing
temperature. Position program selection key to desired washing programtemperature. Select convenient spin
speed related to selected program. If
1
4
you are using auxiliary function press
desired auxiliary function key.
Afterwards place appropriate detergent and softener to your machine’s
detergent drawer. Start your machine
by pressing Start/Pause/Cancel button. Start/Pause/Cancel key’s led will
be on. After your machine starts, you
can follow from the program progress
display at which step your machine is.
3
2
6
5
7
8
Downloaded From WashingMachine-Manual.com Manuals
11
9
Energy
Consumption
(kWh)
60
2.60
6
150
55
2.00
6
135
49
1.14
6
125
49
0.70
6
160
65
1.30
6
170
65
1.40
3
125
60
1.00
3
115
55
0.90
3
105
55
0.50
3
90
55
0.30
3.5
95
55
0.50
2
70
60
0.35
2
65
60
0.25
1.5
55
55
0.30
1.5
45
55
0.03
1
40
35
0.15
2.5
30
45
0.25
Rinse Program
6
23
13
0.04
Spin Program
6
13
_
0.03
Cotton 95 with
Prewash
Heavy soiled Durable fabrics
made of cotton and linen
Heavy soiled Durable fabrics
made of cotton and linen
Normal soiled cotton and linen
durable to heat
Less soiled cotton and linen
sensitive to heat
Heavy soiled Durable fabrics
made of cotton and linen
Normal oiled Durable fabrics
made of cotton and linen (baby
clothes etc.)
Normal soiled cotton/synthetic
blended durable to heat
Normal soiled cotton/synthetic
blended durable to heat
Less soiled cotton/synthetic
blended durable to heat
Very Less soiled or cotton/synthetic blended sensitive to heat
Very Less soiled or cotton/synthetic blended sensitive to heat
Delicate, sensitive synthetic, cotton blended
Delicate, sensitive synthetic, cotton blended
Woolen and delicate blended
with machine wash label
Woolen and delicate laundry with
machine wash sign
Special program for silk, cashmere or laundry with no machine
wash sign
Special program for silk, cashmere or laundry with no machine
wash sign
Cotton 95
Cotton 60 *
Cotton 40
Intensive 60
Hygiene 65
Synthetic 60
with prewash
Synthetic 60
Synthetic 40
Synthetic 30
Mix 40
Delicate 40
Delicate 30
Woolen 40
Woolen Cold
Handwash 30
Mini 30
Rinse
Spin
Pump
Pump Program
_
* Energy Labeling Program (EN 60456)
Downloaded From WashingMachine-Manual.com Manuals
12
2
_
_
•
• •
• •
• •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Anti-creasing
Water
Consumption
(lt)
160
Type of laundry
Rinse Plus
Program Duration (min.)
6
Program
Quick wash
Max Load (kg)
Program selection table
•
•
•
•
•
•
•
•
•
•
•
Pressing “On/Off”
By pressing “On/Off” button you can
make your machine ready for selecting program. When “On/Off” key is
pressed “door” led will light on meaning “door can open”. Press “On/Off”
key again for turning your machine
off.
Function Selection
Pressing “On/Off” does not mean
program started operation. You must
press “Start/Pause/Cancel” for starting the program.
Additional functions selectable according to selected program can be
selected by pressing related key. Led
of selected function will be on.
If not selected together some additional functions go off when it is not
selected with other one. For example;
when using cotton program, exspress
and rinse plus auxillary functions can
not be selected together. After selecting express program, if rinse plus key
is pressed fast program will be on
and express function led will go off.
Child-proof lock
Program Progress
During washing laundry in order to
maintain that program progress is not
affected by pressing keys by children
there is child-proof lock. To enable
child-proof lock, after washing begins,
press Express and Rinse Plus function buttons together simultaneously
for three seconds. Pre-wash additional function led will always blink.
After machine starts operation relevant program led on program progress display will be on. When a step
is completed that step’s led is off and
next step’s led is on. When “On/Off
button is pressed “door” led will be
on. After washing program is selected
when “Start/Pause/Cancel” key is
pressed “Washing” led on program
progress display will be on. At the
final step “Spin cycle” led is on. When
program is completed “Door” led
will be on again. During machine
operation you can press “Start/Pause/
Cancel” key for getting machine to
“Pause” position. In this case “Start/
Pause/Cancel” led will blink.
After program ends in order to start a
new program or alter the program you
have to disable child-proof lock. To
do this press same buttons for three
seconds and Child-proof lock led will
be off.
Downloaded From WashingMachine-Manual.com Manuals
13
Changing Program
can be started with delay. During
delay period door can be opened or
laundry can be added
After time delay is initiated by pressing “Start/Pause/Cancel” you can
switch machine to “Pause” mode and
change delay time.
You can use this feature for washing laundry in the same textile group
for washing at lower or higher temperatures. For example, instead of
Cotton60, Cotton40 can be used.
For selecting Cotton40 instead of
Cotton60 by pressing “Start/Pause/
Cancel” key machine is switched
to pause position. Program knob is
turned for selecting Cotton40 program.
Even when the program selection
button is changed during the program initially selected program will
be executed. For changing washing
program continuing program must be
cancelled. (See Cancelling a program)
For selecting auxillary functions
or spin speed necessary changes
can be performed after pressing
Start/Pause/Cancel button. Although
selected auxillary functions must be
compatible with washing program.
For example when your machine is
intensive program you can select
additional rinse plus function but you
can not select express.
Adding laundry
If you want to add laundry to your
machine after program begins press
Start/Pause key for switching machine to pause mode. If water level
in the machine is appropriate “door”
led on program progress display is
on and laundry can be added to the
machine. If “door” led is not on after
one minute than water level in the
machine is not appropriate and laundry can not be added. You can press
“Start/Pause/Cancel” key for continuing program.
Time delay for program start
Using time delay key you can delay
the starting of the selected program
for 3 hours, 6 hours or 9 hours.
When time delay key is pressed once
3hours delay is adjusted and led
will light on. If same key is pressed
once more delay is 6hours, and if it is
pressed once more 9 hours delay is
selected. If time delay key is pressed
again delay is cancelled. After the
selection of time delay when “Start/
Pause/Cancel” is pressed program
Canceling a Program
For canceling a program “Start/
Pause/Cancel” key is pressed for
three seconds. After this period “Start/
Pause/Cancel” and all other leds will
be off .You can select a new program
and start washing.
If cancel task is performed during
washing “Spin” led on display will
light on, machine will pump and when
“Spin” led is off “door” led will be on,
door can be opened and new pro-
Downloaded From WashingMachine-Manual.com Manuals
14
Emptying Laundry
gram can be selected.
Even program selection button is
changed during the program initially
selected program will be executed.
For changing washing program “Canceling a program” must be performed
afterwards new program can be
selected and started
After machine starts operation even if
spin speed or washing temperature is
changed, initial speed and temperature is valid. In order to change spin
speed or temperature after pressing
“Start/Pause/Cancel” new cycle or
temperature can be selected.
After program ends machine automatically stops. Turn off tap water.
Pull the handle and open loading
door. Turn off your machine by pressing “On/Off”. After taking laundry out
keep the loading door open and let
the drum ventilate. Check the bellow
and clean.
End of Program
When program ends “ door” led will
light on and door can be opened and
machine is ready for next washing.
Press “On/Off” for turning machine
off.
Downloaded From WashingMachine-Manual.com Manuals
15
5
Care and maintanence
Detergent Dispenser
Powder detergent residue may accumulate in drawer after a while. In
order to clean detergent drawer press
the marked point of the siphon on
softener compartment and push the
drawer towards yourself. Wash the
drawer with water
region, if your machine is placed in a
cold place remaining water in hoses
must be drained with pump filter
when machine is not used. Water
inlet hoses can be drained by taking it
out from tap.
Siphon
Do not neglect cleaning suction cup
when it becomes soiled. In order take
suction cup out first take detergent
drawer out. Clean it in order to eliminate blocking by softener residue.
After cleaning place suction cup to
its place and make sure it is placed
properly.
Cleaning Pump Filter
There is filter system maintaning long
lifetime of pump by blocking foreign
objects like button, cloth fiber enter
to the pump during drain of washing
water. It is useful to clean the filter
when it is soiled.
In order to do this:
Unplug your machine. Open the filter
at bottom right corner by pressing
marked space on the lid.
Water Entrance Filters
There is a filter at each flat end where
water inlet hose is connected to
tap and at each of water inlet valve
placed behind the machine. These
filters blocks entrance of foreign
objects and dirts to the machine.
Filters must be cleaned regularly to
avoid clogging. For doing this, turn off
tap water. Pull out water inlet hoses.
Clean the top of the water inlet valve
filter with a brush. If filters are extremely clogged you can pull it out
with a pincer. You can take out the flat
side of water inlet hoses with its seal
and clean with tap water. (2 filters in
Single water inlet machines, 4 filters
in double water inlet machines)
Hot water risk: There might be 15 lt.,
90°C hot water in the drum. Open the
filter carefully.
Before opening the filter drain the
water with drain hose. Pull out the
drain hose from its place. Prepare a
suitable container and open the tap
of hose. After water is drained place
the tap properly. Open the filter by
turning and drain the remaining water
(max30ml) to filter tap. Clean remaining foreign object in the filter. When
Hose
There is risk of freezing in cold
Downloaded From WashingMachine-Manual.com Manuals
16
finished turn in clockwise direction
and close. Close the filter tap by
pushing.
6
Caution!
If the filter and hose tap does not fit, it
leaks water.
Installation
2. Leveling the feet
If your system is not ready, let a certified plumber make it ready.
In order to operate your machine
without noise and vibration it must
be properly on balance. Four feet
of your machine can be adjusted.
First loosen the plastic counter bolt.
Tighten the counter bolt after adjusting the feet for leveling your machine.
1. Removing the transportation
safety bolts
Before the washing machine is operated, the transit bars must be removed! In order to do this:
1. Loosen “C” bolts by rotating them
counter clockwise with a suitable
spanner
2. Remove transportation safety bolts
by turning.
3. Place “P” plastic covers onto the
openings of transportation locks by
rotating in direction of arrow and
pushing.
3. Water Connections
a) Water Inlet Hose
Your machine is connected to water
supply by special hoses supplied by
the machine. Red hose or hose written red on it is hot water inlet, blue
hose or hose written blue on it is cold
water inlet.
Attention please! Keep the transit
bars for using when machine is to be
transported again. Always transport
your machine with transportation
locks.
There are plastic seals (4 for double
Downloaded From WashingMachine-Manual.com Manuals
17
water inlet models, 2 for single water
inlet models) on hose or plastic bag
for eliminating any leakage in connections points. These seals must be
used on each side of the connection.
Seals on machine side must be connected filter cannal.
40 and 100 cm. from the ground.
Water drain hose could be placed
directly to the drain water inlet.
4. Electrical connection
Connect the power cord to the appropirate electrical system which is
being supported by the maximum
voltage and current rating indicated
on the rating plate placed inside the
kick plate.
Look! Page 1, Steps before operating
Fullautomatic Washing Machine and
safety precautions.
Make sure that you have grounded
power outlet.
After connecting the hose, check
all connections for leaks In order to
eliminate any risk due to water leakage keep the taps off when machine
is not used.
Your machine will operate efficiently if
the water from tap is minimum 1 and
maximum 10 bars. Practically 1 bar
means 8 liters of water in one minute
when tap is fully on.
Connect hose to the machine.
Tighten bolts with hand power, do not
use spanner.
Double inlet models can be used with
blind cap as a single inlet machine.
Connect blind cap to hot water inlet.
Seal must be for stopping water leakage.
Attention! Before any operation of the
machine check the following.
• Did you close the front door?
• Is the tap open?
• Is water drain hose placed properly?
• Is power connected?
Do not connect single inlet machine
to hot water. If machine is connected
with Y part to a double inlet and over
40˚C for single inlet machines, machine may switch to protection mode.
b) Water drain hose
Water drain hose could be placed
either at the side of the bath tub, or
directly to the drain. The hose should
not be bent. Water drain hose should
be secured with the holder so that it
would not fall down on the ground.
The hose should be placed between
Downloaded From WashingMachine-Manual.com Manuals
18
7
Before calling service
You turned the machine on, but the
leds are off on the panel.
Check the grounding on the power
cable or a blown fuse. Check the front
door proper closure.
Water coming from beneath the
machine.
Check the water intake and drain
hoses. Tighten the connections. The
washers of the hoses may be worn
out. If non of the both, the pump filter
is not closed properly.
Machine does not take water.
Check the front door for proper closure. Either taps are closed or water
intake filters are clogged.
Foam coming out of the detergent
dispenser.
Check whether your detergent is
suitable for automatic machines. Next
time use less detergent.
Taken water is directly discharged.
Check if the discharge hose placed
as described in the users manual or
not.
Pump does not drain water.
Clean the pump filter. Check whether
the drain hose is bent or not. If there
is need to clean the pump filter, refer
to the pump filter cleaning section of
the manual.
Downloaded From WashingMachine-Manual.com Manuals
19
Downloaded From WashingMachine-Manual.com Manuals