Juno Treadmill
※TABLE OF CONTENTS
1. PRECAUTIONS................................. P3
2. POWER REQUIRMENTS............................. P4
3. BEFORE YOU BEGIN..............................
P5
4. SUPPLIED COMPONENTS / SUPPLIED HARDWARE..............
P6~P7
5. PARTS LIST................................
P8~P11
6. ASSEMBLY INSTRUCTIONS......................... P12~P15
7. EXPLODED DIAGRAM............................ P16~P22
8. STABILIZER ADJUSTMENT.......................... .
P23
10. MAINTAINENCE.............................. P24~P25
11. IMPORTANT STEPS..............................
P26
12. MUSCLE CHART................................P27
13. STRETCHING ROUTINE............................ P28
14. TROUBLESHOOTING............................. P29
15. WARRANTY............................... P30~P31
16. COMPUTER OPERATION......................... P32~P37
Yowza Technical Support: 877-969-9240
Serial Number:
________________________
Original Sales Order # ________________________
Purchase Date:
______________
2
YOWZA JUNO TREADMILL
PRECAUTIONS
Precautions:
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and
information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are
adequately informed of all warnings and precautions.
Use the treadmill only as described in this manual.
Place on a level surface, with 6 feet (2 m) of clearance behind it. Do not place the treadmill on any surface that blocks air
openings. To protect the floor or carpet from damage, place a mat under the treadmill.
When choosing a location for the treadmill be sure that the location and position permit access to a plug.
Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near
water.
Do not operate the treadmill where aerosol products are used or where oxygen is being administered.
Keep children under the age of 12 and pets away from the treadmill at all times.
The treadmill should not be used by persons weighing more than 300LBS.
Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill.
Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both
men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in
sandals.
When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same
circuit.
Always straddle the belt and allow it to start moving before stepping onto the belt.
Always examine your treadmill before using to ensure all parts are in working order.
Allow the belt to fully stop before dismounting.
Never insert any object or body parts into any opening.
Follow the safety information in regards to plugging in your treadmill.
Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not
operate the treadmill with a damaged or frayed power cord.
Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an
authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these
instructions will void the treadmill warranty.
Never leave the treadmill unattended while it is running.
Use “safety key” when operating the treadmill and make sure the “safety key” is clipped to the users clothing.
The cell phone signal might interfere treadmill functions, keep the cell phone away from the motor hood.
Remove the “safety key” and store it in a safe place when the treadmill is not in use. Keep the “safety key” away from
children.
http://www.yowzafitness.com/
3
POWER REQUIREMENTS
Power Requirements:
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC
SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE
PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT
THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and
noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of
treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a
UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an
electrical rating 110VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric
current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding
conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing
below.
GFCI outlets and GFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI Circuit Breakers
may cause this equipment to function improperly.
4
YOWZA JUNO TREADMILL
BEFORE YOU BEGIN
Open the boxes:
Open the boxes of your new equipment. Inventory all parts included in the boxes, and compare them to the Supplied Components
and Supplied Hardware lists on assembling manual for a full count of the parts included. If you are missing any parts or have any
questions contact us directly.
Gather your tools:
Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit properly. Having
all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.
Clear your work area:
Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is free from
anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a comfortable amount of free
area around the unit for unobstructed operation.
Invite a friend:
Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another person when
assembling this product.
User Weight Limitation:
Please note that there is a weight limitation for this product. If you weigh more than 300LBS (Approx. 135 Kgs). It is not
recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown here. This product is
not intended to support users whose weight exceeds this limit.
Care and maintenance:
The safety level can be maintained only if it is examined for damage and wear.
Replace any defective components immediately and stop all use of the equipment until repaired.
Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails. Dismount from the
equipment only after all parts have stopped.
Always check the wear and tear components like pulley, belts, etc.…To prevent injury.
There is an emergency stop, in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill immediately by actuating the
emergency stop for emergency dismount.
http://www.yowzafitness.com/
5
SUPPLIED COMPONENTS
This list identifies the major components you will use to assemble this product.
No.
Description
A1
Console Assembly
1
A2
Main Frame Assembly
1
A3
Right Handlebar Assembly
1
A4
Left Handlebar Assembly
1
111
Safety Key
1
106
Water Bottle Holder
1
201
Upright Cover – LL
1
202
Upright Cover – LR
1
203
Upright Cover – RR
1
204
Upright Cover – RL
1
220
Side Cover
2
C
Power Cord
1
D
Lubricant
1
A1
Qty.
A2
A3
111
106
204
220
A4
201
202
C
203
D
6
YOWZA JUNO TREADMILL
SUPPLIED HARDWARE
This list identifies the hardware you will use to assemble the product. To help distinguish between the various types of
screws and bolts, use the scale below to measure them and compare them to the sizes listed.
No.
Description
Qty.
901
M8x40mm Allen Head Bolt
4
904
M10x62mm Bolt
4
905
3x12mm Screw – Cone Pivot
4
A
6mm Allen Key
1
B
5mm Allen Key
1
E
Screwdriver
1
901
A
MILLIMETERS
904
B
905
E
http://www.yowzafitness.com/
PARTS LIST
Item No.
JUNO-100
101
102
103
104
105
106
107
108
110
111
112
115
JUNO-200
201
202
203
204
205
214
215
216
218
219
220
221
222
223
224
225
226
JUNO-400
401
402
403
404
405
406
407
408
JUN0-500
501
502
503
504
505
506
Description
Qty.
Part No.
Overlay
Computer Insert
Safety Key Holder
Console Housing – Upper
MP3 Insert Cover
Water Bottle Holder
Hand Pulse Sensor Cover – Upper
Hand Pulse Sensor Cover – Lower
Safety Key Seat
Safety Key
Console Support Tube
Console Housing – Bottom
1
1
1
1
1
1
1
1
1
1
1
1
JUNO-101
JUNO-102
JUNO-103
JUNO-104
JUNO-105
JUNO-106
JUNO-107
JUNO-108
JUNO-110
JUNO-111
JUNO-112
JUNO-115
Upright Cover – LL
Upright Cover – LR
Upright Cover – RL
Upright Cover – RR
Right Handlebar
Handlebar Foam Grip
Left Handlebar
Handlebar End Cap
Left Upright
Right Upright
Side Cover
Upright Lower Cover – LL
Upright Pivot Bracket – Left
Upright Lower Cover – LR
Upright Lower Cover – RL
Upright Pivot Bracket – Right
Upright Lower Cover – RR
1
1
1
1
1
2
1
2
1
1
2
1
1
1
1
1
1
JUNO-201
JUNO-202
JUNO-203
JUNO-204
JUNO-205
JUNO-214
JUNO-215
JUNO-216
JUNO-218
JUNO-219
JUNO-220
JUNO-221
JUNO-222
JUNO-223
JUNO-224
JUNO-225
JUNO-226
Skidproof Cushion
Side Rail – Left
Side Rail – Right
Side Rail End Cap
Running Belt
Running Deck
Cushion Pad
Lower Side Rail
48
1
1
2
1
1
8
2
JUNO-401
JUNO-402
JUNO-403
JUNO-404
JUNO-405
JUNO-406
JUNO-407
JUNO-408
Vent Cover
Motor Front Hood
Motor Hood
Motor Hood Pad
Motor Side Hood – Left
Motor Side Hood – Right
1
1
1
1
1
1
JUNO-501
JUNO-502
JUNO-503
JUNO-504
JUNO-505
JUNO-506
7
8
YOWZA JUNO TREADMILL
PARTS LIST
Item No.
507
508
509
510
511
512
513
514
515
516
517
JUNO-600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
622
623
624
625
628
629
630
631
632
634
636
640
JUNO-700
701
702
703
Description
Qty.
Part No.
Elevation Gear Sleeve
Elevation Support Tube
Plastic Bushing
Wheel
Elevation Support Tube Set – Left
Elevation Support Tube Set – Right
Motor Holder
Driving Belt
Power Plate
Motor Bottom Cover #1
Linkage Cover
1
1
2
2
1
1
1
1
1
1
2
JUNO-507
JUNO-508
JUNO-509
JUNO-510
JUNO-511
JUNO-512
JUNO-513
JUNO-514
JUNO-515
JUNO-516
JUNO-517
Control Board
Elevation Control Board
Transformer
Driving Motor
Power Breaker
Power Switch
Elevation Motor
Computer PC Board
Control Board Connection Wire
MP3 Insert Wire
Elevation Control Board Fix Bolt
Power Insert
8pin Power Wire – Upper
8pin Power Wire – Middle
8pin Power Wire – Lower
3C Power Wire
MP3 Connection Wire
3P Power Connection Wire
1pin Power Connection Wire
Hand Pulse Sensor Wire
Receiver
5/16” Cable Tie
3/8” Cable Tie
Safety Key Wire – Upper
Safety Key Wire – Middle
Safety Key Wire – Lower
1P Ground Wire
Speaker
Amplifier PC Board
2pin Amplifier Power Connection Wire
Receiver Wire
1
1
1
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
1
2
1
2
2
1
1
1
1
2
1
1
1
JUNO-601
JUNO-602
JUNO-603
JUNO-604
JUNO-605
JUNO-606
JUNO-607
JUNO-608
JUNO-609
JUNO-610
JUNO-611
JUNO-612
JUNO-613
JUNO-614
JUNO-615
JUNO-616
JUNO-617
JUNO-618
JUNO-619
JUNO-622
JUNO-623
JUNO-624
JUNO-625
JUNO-628
JUNO-629
JUNO-630
JUNO-631
JUNO-632
JUNO-634
JUNO-636
JUNO-640
Front Roller Shaft
Front Roller Tube
Front Roller Pulley
1
1
1
JUNO-701
JUNO-702
JUNO-703
http://www.yowzafitness.com/
PARTS
Item No.
704
705
LIST 707
708
709
710
714
715
716
719
722
JUNO-800
801
802
803
806
807
808
809
820
822
823
824
831
833
835
841
861
863
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
883
Description
Qty.
Part No.
Bearing Bushing
Bearing 6202
Running Deck Support Tube
EVA foam
Rear Stabilizer
Deck Frame
Rear Roller Tube
Rear Roller Shaft
Motor Bottom Cover #2
Deck Frame Bottom Cover
Level Adjuster
4
4
1
1
2
1
1
1
1
1
2
JUNO-704
JUNO-705
JUNO-707
JUNO-708
JUNO-709
JUNO-710
JUNO-714
JUNO-715
JUNO-716
JUNO-719
JUNO-722
3x12mm Screw – Cone Point
4x15mm – Flat Point
4x8mm – Flat Point
4x12mm Screw – Flat Point
M12x25mm Allen Head Bolt
M6x12mm Allen Head CAP Bolt
4x15mm Screw
6.5x13x1.5mm Washer
Handlebar End Cap Holder
6x11x3mm Washer
M6x30mm Allen Head Bolt
25mm C Clip
Bushing 24.85x32-35x16mm
M10x62mm Bolt
4x12mm Plastic Screw
8x22x2mm Washer
M10x50mm Allen Head Bolt
M10 Nylon Nut
M8 Nylon Nut
M8x75mm Bolt
4x12mm Screw – Cone Point
M8x25mm Bolt
8x14x2mm Spring Washer
M8 Nut
M10x40mm Allen Head Bolt
M5x77mm Bolt
15x45-M14x15mm Bolt
Wheel Bushing
Compression Spring
M8x100mm Bolt
M10x142mm Bolt
M8x20mm Bolt
8x16x3mm Washer
Iron Plate Nut
11
16
4
6
2
4
4
7
2
2
2
2
4
1
6
6
2
5
1
8
31
8
14
8
1
2
2
4
1
1
1
2
2
6
JUNO-801
JUNO-802
JUNO-803
JUNO-806
JUNO-807
JUNO-808
JUNO-809
JUNO-820
JUNO-822
JUNO-823
JUNO-824
JUNO-831
JUNO-833
JUNO-835
JUNO-841
JUNO-861
JUNO-863
JUNO-865
JUNO-866
JUNO-867
JUNO-868
JUNO-869
JUNO-870
JUNO-871
JUNO-872
JUNO-873
JUNO-874
JUNO-875
JUNO-876
JUNO-877
JUNO-878
JUNO-879
JUNO-880
JUNO-881
9
10
YOWZA JUNO TREADMILL
COMPUTER OPERATION
Item No.
884
885
890
891
892
895
897
898
JUNO-900
901
904
905
Description
Qty.
Part No.
4.5x1.5nn Screw
Motor Hood Holder
M6x10mm Screw
15x22x1mm Washer
M6x70mm Allen Head CAP Bolt
M8x20mm Allen Head CAP Bolt
5x10mm Screw
3x8mm Screw – Cone Point
6
2
2
7
3
4
2
8
JUNO-884
JUNO-885
JUNO-890
JUNO-891
JUNO-892
JUNO-893
JUNO-897
JUNO-898
M8x40mm Allen Head Bolt
M10x62mm Bolt
3x12mm Screw – Cone Pivot
4
4
4
JUNO-901
JUNO-904
JUNO-905
http://www.yowzafitness.com/
STEP1 ASSEMBLY
STEP1-A
219
218
219
STEP1-B
220
219
904
A
904
904
STEP1-C
219
220
STEP1-A). Rotate the Uprights (118, 119) up to vertical position.
STEP1-B). Using the two M10x62mm Bolts (904) to secure the upright to frame.
STEP1-C). Attach the Side Cover (220) to the frame.
904 X4
220 X2
220
11
12
YOWZA JUNO TREADMILL
STEP2
ASSEMBLY
STEP2-A
901
613
614
901
112
628
629
219
218
A4
613
614
112
628
629
STEP2-B
218
219
112
A3
219
STEP2-C
901
A3
219
STEP2-A). Connect the 8pin Power Wire – Upper (613) to 8pin Power Wire – Middle
(614) and Safety Key Wire – Upper (628) to Safety Key Wire – Middle (629).
STEP2-B). Attach the Console Support Tube to the Upright and Attach the Handlebar
(A3, A4) to the Console Support Tube.
STEP2-C). Using the Allen Head Bolt (901) to secure the Handlebar and
Console Support Tube to the Upright.
901
X4
A3
http://www.yowzafitness.com/
STEP3
13
ASSEMBLY
201
201
202 905
215
202
905
203
204
218
205 219
E
218
STEP3). Attach the Upright Cover (201, 202) to the Left Upright tube, and secure using
the Cone Point Screw (905).
Repeat the above process for the Right side.
905
X4
14
YOWZA JUNO TREADMILL
STEP4
ASSEMBLY
106 104
STEP4). Attach the water bottle holder (106) to the left side console.
Your treadmill is now fully assembled.
106
X1
http://www.yowzafitness.com/
898
15
898
104
102
632
632
106 803
802
115
803
802
802
107
110
103
809
898
809
112
802
901
802
105
901
108
214
205
822
215
216
824
822
823
820
EXPLODED DIAGRAM
801
823
214
820
216
824
802
16
YOWZA JUNO TREADMILL
898
898
104
102
632
632
106 803
802
115
803
802
802
107
110
103
809
898
809
112
802
901
802
105
901
108
214
205
822
215
216
824
822
823
820
EXPLODED DIAGRAM
801
823
214
820
216
824
802
http://www.yowzafitness.com/
17
905
201
202
203
204
218
219
831
220 806
221 904
833 223
807 222
806 224
833
865C
865C
EXPLODED DIAGRAM
831
225 807
904
226 806
220
18
YOWZA JUNO TREADMILL
401
867
401
401
401
867
401
401
401
401
402
401
404
868
401
403
404
868
408
405
841
408
841
869
406
407
870
870
871
870
EXPLODED DIAGRAM
http://www.yowzafitness.com/
501
868
868
502
883
801
883
612
503
504 865
884
607 872
873 874
875
868
505 509
835
884
873
506
507 865
510
508
511
868
602
868
625
510
861C
870C
603
895
509
861C
870C
876
877
878
875 874
512
866
861
601 611
868
879
513
895
868 624
880
870
865
515
604
606
514
897
868
605
716
898
898
883
868
EXPLODED DIAGRAM
884 868
868
883 884
517
516
883 868
19
20
YOWZA JUNO TREADMILL
892
891
820
701
705
704
624
702
885
703
868
704
885
708 707
863 709
890
865 891
710
868 625
705
704
705
722
709 863
820
892
715 714 891 865
722
719
WIRE DIAGRAM
868
841
705
891
http://www.yowzafitness.com/
622
21
636
640
632
632
634
623
617
622
610
622
613
614
608
629
628
613
606
612
605
630
614
609
615
628
602 618 616 619
629
615
630
603
601
607
604
22
YOWZA JUNO TREADMILL
STABILIZER ADJUSTMENT
FOLLOW THESE INSTRUCTIONS TO LEVEL YOUR TREADMILL:
An uneven floor or improper stabilizer level can cause the treadmill to wobble during use as well as the incline adjustment to function
incorrectly. Please follow the procedure described below to make sure the treadmill stabilizer is adjusted correctly prior to use. You
may need the assistance of another person to perform this adjustment.
First locate the two adjustable stabilizers under the base frame. Then simply rotate them in or out to adjust the level of the
treadmill. When properly adjusted the treadmill should sit firmly on both stabilizers and all cushions.
Locate the two adjustable stabilizers under the base frame.
Treadmill should sit firmly on both stabilizers and all cushions.
http://www.yowzafitness.com/
23
MAINTENANCE
HOW TO MAINTAIN THE JUNO TREADMILL:
Proper maintenance is very important to ensure your treadmill is always in top working condition. Improper maintenance could
cause damage or shorten the life of your treadmill and exceed the LIMITED WARRANTY coverage.
Important: DO NOT use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids
away and keep it out of direct sunlight.
Inspect and tighten all parts of the treadmill regularly. Replace any damaged or worn parts immediately.
BELT ADJUSTMENT:
ALL BELT ADJUSTMENTS ARE CONSIDERED MAINTENANCE, AND ARE THE RESPONSIBILITY OF THE END USER.
Belt adjustment and tension performs two functions: adjustment for tension and centering. The running belt has been adjusted
properly at the factory. However transportation, uneven flooring or other unpredicted reasons could cause the belt to shift off center
resulting in the belt rubbing on the plastic side rail or end caps and possibly causing damage to the equipment. To adjust the belt
back to it’s proper position please follow the directions below:
Walking belt has shifted to the left: First unplug the power cord from the surge protector. Using the hex key provided,
turn the left rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center.
Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you
have completed this procedure if the belt feels like it is slipping while walking. Refer below to the "Walking belt slipping"
instructions.
Walking belt has shifted to the right: First unplug the power cord from the surge protector. Using the hex key provided,
turn the right rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center.
Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you
have completed this procedure if the belt feels like it is slipping while walking. Refer below to the "Walking belt slipping"
instructions.
Walking belt is slipping: First unplug the power cord from the surge protector. Using the hex key provided, turn both the
left and right rear roller adjustment bolts the equal amounts , 1/2 turn in the clockwise direction. Plug the power cord back
into the surge protector and run the treadmill at 2.5 mph. You should now walk on the belt to determine if the belt is still
slipping. Repeat the above procedure until the walking belt is not slipping. The tension should be just tight enough not to
slip. If proper tension cannot be achieved within four attempts please contact Yowza Fitness Technical Support. Belt
centering may be necessary once you have completed the tensioning procedure.
WARNING! Do not over tighten rollers! This will cause premature roller bearing failure!
Right and left tension bolts are located at the rear of the treadmill.
24
YOWZA JUNO TREADMILL
MAINTENANCE
CLEANING:
Routine cleaning of your treadmill will extend the product's life.
Warning: To prevent electrical shock, be sure the power to the treadmill is OFF and the power cord is unplugged from the
wall electrical outlet before attempting any cleaning or maintenance.
Important: DO NOT use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids
away and keep it out of direct sunlight.
After each workout: Wipe off the console and other treadmill surfaces with a clean, water dampened soft cloth to
remove excess perspiration.
Weekly: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and
eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.
DECK LUBRICATION:
The walking belt has been pre-lubricated at the factory. However, it is recommended that the running deck be checked periodically
for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be lubricated usually within the first 400
hours of use.
Every 2 months of operation lift the sides of the walking belt and feel the top surface of the running deck as far as you can reach. If
you feel signs of silicone, no further lubrication is required. If it feels dry to the touch, follow the instructions below.
To apply lubricant under the walking belt:
1.
Position the walking belt so that the seam is located on top and in center of the walking board.
2.
Insert the spray nozzle into the spray head of the lubricant can.
3.
While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board approximately 6"
from the front of the treadmill and as far to the center as possible. Apply the silicone spray to the walking board, moving
from the front of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 1/4 bottle
(supplied with treadmill) each time.
Allow the silicone to "set" for 1 minute before using the treadmill.
Spray lubricant from to back.
http://www.yowzafitness.com/
25
IMPORTANT STEPS
Warning:
Before using this product, please consult your personal physician for a complete physical examination. Frequent and strenuous
exercise should be approved by your doctor first. If any discomfort should result from your use of this product, stop exercising and
consult your doctor. Proper usage of this product is essential. Please read your manual carefully before exercising.
Please keep all children away from the equipment during use and when equipment is unattended.
Always wear appropriate clothing, including athletic shoes, when exercising. Do not wear loose clothing that could become caught
during exercising.
Make sure that all bolts and nuts are tightened when equipment is in use. Periodic maintenance is required on all exercise
equipment to keep it in good condition.
Before beginning:
How you begin your exercise program depends on your physical condition. If you have been inactive for several years, or are
severely overweight, you must start slowly and increase your time gradually, a few minutes per week.
Initially you may be able to exercise only for a few minutes in your target zone. However, your aerobic fitness will improve over the
next six to eight weeks. Don’t be discouraged if it takes longer. It’s important to work at your own pace. Ultimately, you’ll be able
to exercise continuously for 30 minutes. And the better your aerobic fitness, the harder you will have to work to stay in your target
zone. But remember these essentials:
Contact your physician before starting a workout or training program. Have your doctor review your training and diet
programs to advise you of a workout routine you should adopt.
Begin your training program slowly with realistic goals that have been set by you and your doctor.
Supplement your program with some type of aerobic exercise such as walking, jogging, swimming, dancing and/or
bicycling. Monitor your pulse frequently. If you do not have an electronic heart rate monitor, have your physician show
you the proper way to manually check your pulse by using your wrist or neck. Establish your target heart rate based on
your age and condition.
Drink plenty of fluids during the course of your routine. You must replace the water content lost from excessive exercising
to avoid dehydration. Avoid drinking large amounts of cold liquids. Fluids should be at room temperature when
consumed.
26
YOWZA JUNO TREADMILL
MUSCLE CHART
Targeted muscle groups:
The exercise routine that is performed on this product will develop primarily lower body muscle groups. These muscle groups are
shown in gray color on the chart below.
MUSCLE GROUPS
A
Shoulder muscles
B
Pectoral muscles
C
Bicep muscle
D
Abdominal muscles
E
Forearm muscles
F
Quadricep muscles
Calf muscles
G
Trapezius muscles
H
Tricep muscles
I
Back muscles
J
Gluteal muscles
K
Hamstring muscles
L
http://www.yowzafitness.com/
27
STRETCHING ROUTINE
Warm up and cool down:
A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down. Do the entire program at least two and
preferably three times a week, resting for a day between workouts. After several months, you can increase your workouts to four or
five times per week.
Warming up is an important part of your workout, and should begin every session. It prepares your body for more strenuous
exercise by heating up and stretching out your muscles, increasing your circulation and pulse rate, and delivering more oxygen to
your muscles. At the end of your workout, repeat these exercises to reduce sore muscle problems. We suggest the warm-up and
cool-down exercises on the following pages:
Toe Touch:
Slowly bend forward from
your waist, letting your back
and shoulders relax as you
stretch toward your toes.
Reach down as far as you
can and hold for 15 counts.
Shoulder Lift:
Lift your right shoulder up
toward your ear for one
count. Then lift your left
shoulder up for one count as
you lower your right
shoulder.
Inner Thigh Stretch:
Sit with the soles of your feet
together with your knees
pointing outward. Pull your
feet as close into your groin
as possible. Gently push
your knees towards the floor.
Hold for 15 counts.
Hamstring Stretch:
Sit with your right leg
extended. Rest the sole of
your left foot against your
right inner thigh. Stretch
toward your toe as far as
possible. Hold for 15 counts.
Relax and then repeat with
left leg extended.
Side Stretch:
Open your arms to the side
and continue lifting them until
they are over your head.
Reach your right arm as far
upward toward the ceiling as
you can for one count. Feel
the stretch up your right side.
Repeat this action with your
left arm.
Calf-Achilles Stretch:
Lean against a wall with your
left leg in front of the right
and your arms forward. Keep
your right leg straight and the
left foot on the floor; then
bend the left leg and lean
forward by moving your hips
toward the wall. Hold, and
then repeat on the other side
for 15 counts.
Head Roll:
Rotate your head to the right
for one count, feeling the
stretch up the left side of your
neck. Next, rotate your head
back for one count, stretching
your chin to the ceiling and
letting your mouth open.
Rotate your head to the left
for one count, and finally,
drop your head to your chest
for one count.
28
YOWZA JUNO TREADMILL
TROUBLESHOOTING
NOTE: Do not touch any internal electric wires without consulting the manufacturer.
Treadmill will not start:
Symptom
Treadmill will not power up
Resolution
Check the following:
 Make sure the power cord is plugged into a
surge protector, the surge protector is
plugged into a properly grounded outlet and
the surge protector is turned on (refer to the
Power Requirements section in this manual).
 Equipment circuit breaker is in the reset
position
 Equipment power switch is in the on position
 Safety key is properly inserted into the
computer console
 Wall outlet is properly functioning with correct
voltage (Have an electrician check for
inadequate voltage at the outlet refer to the
Power Requirements section in this manual)
 House circuit breaker is reset and is the
proper size. (refer to the Power
Requirements section in this manual)

Treadmill stops operation during use
Treadmill will not incline(Power fold models only)
Treadmill will not unfold
Treadmill running belt moves slower than speed
displayed on computer
Treadmill running belt moves slower than speed
displayed on computer
Running belt is not centered
Running belt is slipping or hesitating while in use
Treadmill running belt moves slower than speed
displayed on computer
Safety key is properly inserted into the
computer console
 Equipment circuit breaker is in the reset
position
 House circuit breaker is reset, meets proper
requirements and if worn replaced by an
electrician. (refer to the Power Requirements
section in this manual)
 Program time has expired
 Check for proper positioning of spring knob for
folding(See procedure in owners manual)
Power Fold only
 Check for proper positioning of spring knob
for folding(See procedure in owners manual)
Manual Fold only
 Folding locking lever is depressed
 Metric/English conversion (See owners manual
for Metric/English conversion process)
 Metric/English conversion (See owners manual
for Metric/English conversion process)
 Treadmill is properly leveled(See procedure
in owners manual)
 Center running belt (See Centering
procedure in owners manual)
 Tension running belt (See process in owners
manual)
 Metric/English conversion (See owners manual
for Metric/English conversion process)

Running belt is not centered
Running belt is slipping or hesitating while in use
Treadmill is properly leveled(See procedure
in owners manual)
 Center running belt (See Centering
procedure in owners manual)
 Tension running belt (See process in owners
manual)
http://www.yowzafitness.com/
WARRANTY
29
30
YOWZA JUNO TREADMILL
NOTE: Save this document for your records. This warranty include all YOWZA “JUNO” Products
TO OBTAIN SERVICE: CALL 877-969-9240 OR EMAIL SERVICE@YOWZAFITNESS.COM to report a service issue or
manufacturers defect. At the sole discretion of YOWZA FITNESS, Yowza will provide one of the following methods to resolve the
service claim: a) dispatching of an authorized independent service technician to repair the product in the home, b) reimburse the
customer at a rate of $75.00 per service issue. Service issue is defined as an approved service claim. Limit of one $75.00 payment
will be made on each service claim. All repairs must be authorized by YOWZA FITNESS prior to performance of work. Claims on
unauthorized repairs may be denied. Many oversights, which are not covered under this Agreement, can be due to simple
circumstances such as the Covered Product not being switched on, being unplugged, or a fuse blown at the junction box.
WHO IS COVERED: THIS LIMITED WARRANTY IS OFFERED ONLY TO BUYER(s) WHO PURCHASED THE PRODUCT FROM
YOWZA OR ONE OF OUR AUTHORIZED DEALER’S IN THAT AUTHORIZED TERRITORY. THIS LIMITED WARRANTY IS NOT
OFFERED TO BUYER(S) WHO PURCHASED THE PRODUCT FROM ANY OTHER SOURCE, The terms “you” and “your” are
used in this Limited Warranty to refer to the original buyer who purchased the product form YOWZA or one of our authorized
dealers in that dealer’s authorized territory, and any person receiving the product in an unused condition as a gift from such original
buyer. The terms “we“, “us” and “YOWZA” are used in this Limited Warranty to refer to YOWZA International, Inc.
WHAT IS COVERED: This Limited Warranty covers all products that are sold under the YOWZA “JUNO” name to buyers who
purchased the product from YOWZA or one of our authorized dealers in that dealer’s authorized territory and used in United States
and Canada. Except as otherwise stated in this Limited Warranty, we will repair or correct any product or part defect occurring
during the stated WARRANTY PERIOD which we determine is related to materials or workmanship and is not due to normal wear
and tear.
WHAT IS NOT COVERED: THIS LIMITED WARRANTY DOES NOT COVER PRODUCTS PURCHASED FROM ANY SOURCE
THAN YOWZA OR ONE OF OUR AUTHORIZED IN THAT DEALER’S AUTHORIZED TERRITORY. PRODUCTS SOLD, MOVED
OR USED OUTSIDE THE BORDERS OF THE CONTINENTAL UNITED STATES AND CANADA ARE SUBJECT TO THE TERMS
PROVIDED BY THE LOCAL DISTRIBUTOR AND ARE NOT COVERED BY THIS LIMITED WARRANTY. Product requires normal
maintenance including, but not limited to, regular inspection and wear component replacement. We do not warrant damage caused
by the lack of normal maintenance repairs such as those detailed within the Owner’s Manual. We do not warrant any causes
beyond our control. Corrosion, oxidation or deterioration caused by product location, exposure or environment, or conditions
caused by unsuitable finishes, cleaners, or lubricants are not covered. Loss from natural disasters such as hurricanes, floods,
tornados etc. are not covered. Damage or breakage caused by unauthorized service, installation, alteration, modification, assembly
or disassembly, negligence, or conditions of use which are unintended for the product are not warranted. This Limited Warranty
does not cover cosmetic or surface corrosion resulting from chips or scratches in the paint. Extra expenses including, but not
limited to, loss of machine use and inconvenience are not covered. Due to varying conditions under which the product is used, we
offer no warranties, express or implied, as to the length of service. We do not warrant products that have not been paid for, or in the
event that we have offered a payment plan, products purchased by buyers who are in arrears on a payment plan. THIS LIMITED
WARRANTY DOES NOT COVER UNINTENDED USE. See “INTENDED USE” below.
INTENDED USE: This Limited Warranty covers only defects that arise in the ordinary, intended use of the product. Products sold
under the YOWZA “KEEWADIN” name are intended for RESIDENTIAL USE ONLY. See further “Circumstances and use that will
void your warranty “below.
CIRCUMSTANCES AND USE THAT WILL VOID YOUR WARRANTY: Any use other than for residential purpose including but not
limited to: use in a commercial business, use in a member paid organization or association, use in an outside the home office or
location of any kind that is not the residence of the buyer, immediate household members or family. Willful disregard for the proper
maintenance, use and location of the equipment. Loss from natural disasters such as hurricanes, floods, tornados etc. are not
covered.
WARRANTY PERIOD: The warranty period begins on the date on the product was delivered to the original buyer. The warranty
period for lifetime frame and motor, and five years on all other parts. The labor portion of the warranty is two years from the date of
delivery.
WHO WILL PAY LABOR AND TRANSPORTATION COSES: If we determine, during the first year of the warranty period, that the
product or any covered part must be shipped to the manufacturing facility for repair or service, all warranty repairs, including
transportation costs and labor, will be made at NO CHARGE to you; thereafter, you will be responsible for all costs of repair and
service, including labor and transportation costs.
WHAT YOU MUST DO TO OBTAIN WARRANTY COVERAGE DO TO OBTAIN WARRANTY COVERAGE: Retain proof of
purchase. All warranty repairs and corrections require proof of purchase. To obtain coverage, please contact YOWZA Technical
Support (877-969-9240) within seven (7) days after discovery of the defect and follow the directions provided to you by your
YOWZA Service Representative.
MODIFICATIONS TO WARRANTY ARE NOT AUTHORIZED: No one is authorized to modify, change, transfer or extend in any
way the terms of this Limited Warranty.
http://www.yowzafitness.com/
31
WARRANTY
DISCLAIMER OF WARRANTIES AND LIMITATION OF REMEDIES: It is impossible to eliminate all risks inherently associated
with use of the product. Personal injury or other unintended consequences may result because of factors beyond our control. WE
MAKE NO OTHER WARRANTIES OF ANY KIND. EXPRESS OR IMPLIED, OTHER THAN THOSE EXPRESSLY SET FORTH
WITHIN THIS DOCUMENT. ALL WARRANTIES OTHER THAN THE WARRANTIES EXPRESSLY PROVIDED HEREIN ARE
SPECIFICALLY EXCLUDED. IN THE CASE OF NON-CONSUMER BUYERS, ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
IN THE CASE OF A CONSUMER BUYER, THE DURATION OF ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTIES PROVIDED
WITHIN THIS DOCUMENT.
WE WILL NOT BE LIABLE FOR ANY DIRECT OR INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES, LOSSES OR
EXPENSES, INCLUDING BUT NOT LIMITED TO COMMERCIAL LOSSES, BUSINESS INTERRUPTION, OR DAMAGE TO
PROPERTY OTHER THAN THE PRODUCT OR PRODUCTS TO WHICH THIS LIMITED WARRANTY APPLIES.
EFFECT OF STATE LAWS: Some States do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which
vary from State to State. If there is a section in there Bout disputes it should read that all disputes must be litigated in Collier county
Florida.
ALTERNATIVE DISPUTE RESOLUTION FOR NON-CONSUMER BUYERS: WE RESERVE THE RIGHT TO MANDATE
ALTERNATIVE DISPUTE RESOLUTION TO SETTLE ANY OR ALL CLAIMS RESULTING FROM THIS SALES TRANSACTION.
ALTERNATIVE DISPUTE RESOLUTION PROCEEDINGS WILL BE CONSUCTED IN THE STATE OF FLORIDA ACCORDING TO
THE COMMERCIAL RULES OF THE AMERICAN ARBITRATION ASSOCIATION.
32
YOWZA JUNO TREADMILL
COMPUTER OPERATION
A
I
H
G
B
C
D
E
F
LCD DISPLAY
A
B
INCLINE UP/DOWN BUTTON
STOP/ENTER BUTTON
C
D
EXPRESS INCLINE BUTTONS
SAFETY KEY INSERT
E
F
EXPRESS SPEED BUTTONS
START BUTTON
G
H
SPEED UP/DOWN BUTTON
MODE BUTTON
I
http://www.yowzafitness.com/
33
COMPUTER OPERATION
START
Press to start exercise initial speed 0.5 ml/0.8 km.
STOP / ENTER
1. Press to confirm program and preset function values under setting mode.
2. Press to quit preset program and function value after complete single program.
3. Setting procedure: returns to beginning of setting mode before pressing the START key.
4. Press to stop exercise during workout time.
SPEED UP / DOWN BUTTON
1. Press to increase/decrease exercise speed by 0.1ml /km.
2. Hold the button to increase/decrease rapid speed by 0.5ml/km per second and release the button to stop the function.
Press to select programs and preset related function value.
INCLINE UP/DOWN BUTTON
1. Press to increase/decrease incline level.
2. Hold the button to increase/decrease incline level per second and release the button to stop the function.
EXPRESS SPEED BUTTON
Press the quick speed button to select the target speed.
EXPRESS INCLINE BUTTON
Press the quick incline button to select the target incline.
MODE BUTTON
Please MODE button the exchange the display
IMPORTANT
· The console display will turn itself off automatically about five minutes after the bell has stopped moving.
· The pulse function is for reference only, and not to be used for medical purposes.
SAFETY KEY
The safety key must be inserted into the slot on the console in order to operate the treadmill. Always insert the safety key and attach
the clip to your clothing waist before beginning your workout.
If you should encounter problems and need to stop the motor quickly, simply pull on the cord the disengage the safety key from the
console. To continue operation simply turn the power switch to off, set the speed controller to stop and then reinsert the safety key
into the console.
34
YOWZA JUNO TREADMILL
COMPUTER OPERATION
COMPUTER OPERATION
Power on monitor full for 2 seconds. P1 will blink in the upper right window, press UP/DOWN keys for desired program. Press
STOP/ENTER to confirm selected program or press the START key directly to start exercise without a function value.
Please see instructions next for different program options.
QUICK START
Press the start button enter into the QUICK START MODE when the LCD display “P1”
-TIME: Accumulates and displays workout time from start of exercise.
-DISTANCE: Accumulates and displays workout distance from start of exercise.
-CALORIES: Accumulates and displays calories consume during workout time.
-SPEED: Displays current speed.
PROGRAM 1 –TIME
1. Press STOP/ENTER to confirm the program and press START button to start exercise.
2. Press STOP/ENTER before starting exercise to run presetting procedure, with P1 blinking.
-TIME: Press SPPED UP/DOWN button to run preset time target value and press START key.
-DISTANCE: Accumulates and displays workout distance from start of exercise.
-CALORIES: Accumulates and displays calories consume during workout time.
-SPEED: Displays current speed.
PROGRAM 2 –DISTANCE
1. Press STOP/ENTER to confirm the program.
2. Press STOP/ENTER before starting exercise to run presetting procedure, with P2 blinking.
-DISTANCE: Press SPEED UP/DOWN keys to preset the distance target values and press START
-TIME: Accumulates and displays workout time from start of exercise.
-CALORIES: Accumulates and displays calories consume during workout time.
-SPEED: Displays current speed.
PROGRAM 3 – CALORIES
1. Press STOP/ENTER to confirm the program and press START key to start exercise.
2. Press STOP/ENTER before starting exercise to run presetting procedure, with P3 blinking.
-CALORIES: Press SPEED UP/DOWN keys to run preset calories target value and press START key.
-TIME: Accumulates and displays workout time from start of exercise.
-DISTANCE: Accumulates and displays workout distance from start of exercise.
-SPEED: Displays current speed.
http://www.yowzafitness.com/
35
COMPUTER OPERATION
PROGRAM 4 – 15 MINUTES PRESET SPEED
1. Press STOP/ENTER to confirm the program.
2. Press START key to start the exercise, or press STOP/ENTER before starting exercise to run preset procedure with P4 blinking.
3. The LCD will display “L1” after press the STOP/ENTER button, and press SPEED UP/DOWN to select the level from 1 to 7, and then
press STOP/ENTER button to confirm.
-TIME: Accumulates and displays workout time from start of exercise.
-DISTANCE: Accumulates and displays workout distance from start of exercise.
-PULSE: Detects and displays current heart rate.
-CALORIES: Accumulates and displays calories consume during workout time.
-SPEED: Displays current speed.
LEVEL
1
2
3
4
5
6
7
Time
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
0 ~1
0.8/0.5
0.8/0.5
0.8/0.5
0.8/0.5
0.8/0.5
0.8/0.5
0.8/0.5
1~3
3.2/2.0
4.0/2.5
4.8/3.0
5.6/3.5
6.4/4.0
7.2/4.5
8.0/5.0
3~5
4.8/3.0
5.6/3.5
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
5~6
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
6~7
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
7~8
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
8~9
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
13.6/8.5
9~10
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
10~11
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
11~12
4.8/3.0
5.6/3.5
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
12~13
3.2/2.0
4.0/2.5
4.8/3.0
5.6/3.5
6.4/4.0
7.2/4.5
8.0/5.0
13~15
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
PROGRAM 5 – 30MINUTES PRESET SPEED
1. Press STOP/ENTER to confirm the program.
2. Press START key to start exercise or press STOP/ENTER before starting exercise to run preset procedure with P5 blinking.
3. The LCD will display “L1” after press the STOP/ENTER button, and press SPEED UP/DOWN to select the level from 1 to 7, and then
press STOP/ENTER button to confirm.
-TIME: Accumulates and displays workout time from start of exercise.
-DISTANCE: Accumulates and displays workout distance from start of exercise.
-PULSE: Detect and displays current heart rate.
-CALORIES: Accumulates and displays calories consume during workout time.
-SPEED: Displays current speed.
LEVEL
1
2
3
4
5
6
7
Time
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
0 ~1
0.8/0.5
0.8/0.5
0.8/0.5
0.8/0.5
0.8/0.5
0.8/0.5
0.8/0.5
1~3
3.2/2.0
4.0/2.5
4.8/3.0
5.6/3.5
6.4/4.0
7.2/4.5
8.0/5.0
3~7
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
7~11
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
11~18
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
13.6/8.5
18~25
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
25~29
4.8/3.0
5.6/3.5
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
29~30
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
PROGRAM 6 – 45 MINUTES PRESET SPEED
1. Press STOP/ENTER to confirm the program.
2. Press START key to start exercise or press STOP/ENTER before starting exercise to run preset procedure with P6 blinking.
3. The LCD will display “L1” after press the STOP/ENTER button, and press SPEED UP/DOWN to select the level from Level 1 to Level
7 , and then press STOP/ENTER button to confirm.
-TIME: Accumulates and displays workout time from start of exercise.
-DISTANCE: Accumulates and displays workout distance from start of exercise.
-CALORIES: Accumulates and displays calories consume during workout time.
-SPEED: Displays current speed.
LEVEL
1
2
3
4
5
6
7
Time
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
KM/ML
0~1
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1.6/1.0
1~3
3.2/2.0
4.0/2.5
4.8/3.0
5.6/3.5
6.4/4.0
7.2/4.5
8.0/5.0
3~7
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
7~10
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
13.6/8.5
10~14
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
14~16
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
16~17
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
13.6/8.5
17~21
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
21~22
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
22~24
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
13.6/8.5
24~28
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
28~29
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
29~31
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
13.6/8.5
31~35
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
35~36
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
36~38
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
13.6/8.5
38~42
6.4/4.0
7.2/4.5
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
42~43
8.0/5.0
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
43~44
8.8/5.5
9.6/6.0
10.4/6.5
11.2/7.0
12.0/7.5
12.8/8.0
13.6/8.5
44~45
3.2/2.0
3.2/2.0
3.2/2.0
3.2/2.0
3.2/2.0
3.2/2.0
3.2/2.0
36
YOWZA JUNO TREADMILL
COMPUTER OPERATION
PROGRAM 7-WEIGHT LOSS
1. Press STOP/ENTER to confirm the program.
2. Press START key to start exercise or press STOP/ENTER before starting exercise to run preset procedure with P7 blinking.
3. The LCD will display “L1” after press the STOP/ENTER button, and press Speed up /down to select the level from Level 1 to Level 7,
Then press the STOP/ENTER to confirm the setting. and the TIME LCD displays a blinking 32:00. Press the SPEED UP/DOWN to
adjust the total workout time and press the STOP/ENTER to confirm the setting.
Press the START button to start the workout. The SPEED and INCLINE follow the pre-set workout load chart. The TIME counts down
from the set up workout time. Distance and Calories count up from 0.
LEVEL
1
2
3
4
5
6
7
MIN. speed KM/ML MAX. speed KM/ML MIN. level
3.2/2.0
5.6/3.5
0
4.0/2.5
6.4/4.0
1
4.8/3.0
7.2/4.5
2
5.6/3.5
8.0/5.0
3
6.4/4.0
8.8/5.5
4
7.2/4.5
9.6/6.0
5
8.0/5.0
10.4/6.5
6
MAX. level
4
5
6
7
8
9
10
During the workout, users can override the speed by pressing the SPEED UP/DOWN buttons and override the incline level by pressing
the INCLINE UP/DOWN buttons.
SHIFT PROGRAMS AMONG PROGRAM 5, PROGRAM 6 AND PROGRAM 7
If you want to shift new program after you confirmed the program with STOP/ENTER key, press STOP key then original program e.g.
P5, P6 or P7 blinking, and press SPEED UP/DOWN key to choose desire program then press STOP/ENTER to confirm it, with START
key pressing, the treadmill works as you want.
PROGRAM 8 – HEART RATE CONTROL
If P8 is selected, the TIME LED window shows the factory setting value of “60:00” and is blinking. Press the SPEED UP/DOWN buttons
to adjust the workout time. Every adjustable section equals 3 minutes. Press the STOP/ENTER button to save the setting then the
TARGET HEART RATE displays in the PULSE LED window and is blinking. The factory TARGET HEART RATE setting is based on
85% of the maximum user heart rate. The maximum user heart rate is calculated using the formula: 220 minus the user age. As an
example, for age 35 the maximum user heart rate should be 185 and 85% of the maximum user heart rate will be 157. Press the
SPEED UP/DOWN buttons to adjust the TARGET HEART RATE according to your own physical condition or your doctor’s instruction
then press the STOP/ENTER buttons to save the setting.
Press the START button to start the three minute WARM UP program. Speed starts from 2.0 mph /3.2 km/h and the INCLINE LEVEL
starts from level 0. Keep your hand on the hand pulse grips all the time during this workout in order to monitor your pulse correctly.
During the program, if the heart rate monitor fails to sense the user’s pulse you will see “P” blinking in the PULSE LED window. If the
heart rate monitor senses the pulse properly the PULSE DOT LED blinks and the correct pulse readout shows on the PULSE LED
window. The computer will sense the user’s pulse every 30 seconds. During the warm up program you can press the STOP/ENTER
button to pause or stop the program or press the START button to re-start the program. Other buttons will not react during this warm up
process.
During the warm up program, if the heart rate monitor fails to sense the user’s pulse (the PULSE LED will display a blinking “P”) the
computer will not change the speed. If the heart rate monitor senses the user’s pulse properly but the actual user’s pulse does not
reach 65% of the max. heart rate (( 220-age) x 65%) then the speed will increase by 0.5 mph /0.8 km/h every 30 seconds. If the actual
pulse reaches 65% of the max. heart rate the speed will remain unchanged. If the actual pulse remains at 65% of the max. heart rate
for more than one minute the speed will be maintained until the warm up program is finished.
If the actual user’s pulse fails to reach 65% of the max. heart rate within the first 3 minutes of the warm up program, the computer will
continue a second 3 minute warm up program. All workout information continues to count up and the timer counts down from 3:00.
During the second 3 minute warm up the computer will change the incline level instead of the speed. If the heart rate monitor fails to
sense the user’s pulse (the PULSE LED will display a blinking “P”) the computer will not change the incline level. If heart rate monitor
senses the user’s pulse properly but the actual user’s pulse does not reach 65% of the max. heart rate (( 220-age) x 65%) then the
incline level will be increased by 1 level every 30 seconds. If the actual pulse reaches 65% of the max. heart rate the incline level will
remain unchanged. If the actual pulse remains at 65% of the max. heart rate for more than one minute the speed will be maintained
until the warm up program is finished.
http://www.yowzafitness.com/
37
COMPUTER OPERATION
If the actual user’s pulse fails to reach 65% of the max. heart rate within the second 3 minute warm up, the computer will continue a
third 3 minute warm up program. All workout information continues to count up and the timer counts down from 3:00. During the third 3
minute warm up both speed and incline remain unchanged regardless the actual pulse. If the time counts down to 0 and 65% of the
max. heart rate still cannot be achieved then the TIME LED will show “FAIL” and the program will stop and return to POWER ON status.
After the warm up program is completed, if the actual pulse reaches 65% of the max. heart rate, the computer will enter the HEART
RATE CONTROL program. TIME counts down from the previous setting. Distance and Calories continue to count up from the warm up
program. During the HEART RATE CONTROL program the heart rate monitor will sense the actual user’s pulse every 30 seconds. If
the actual user’s pulse does not reach 85% of the max. heart rate then the incline level will be increased by 1 level every 30 seconds. If
the actual user’s pulse reaches 85% of the max. heart rate then the treadmill performance will be remain unchanged. If the actual
user’s pulse is greater than 85% of the max. heart rate, the incline level will be reduced by 1 level. Speed will remain unchanged until
the incline level increases up to 15% or down to 0%. If the incline level is up to 15% and 85% of the max. heart rate still cannot be
reached then the speed will be increased by 0.5 mph /0.8 km/h every 30 seconds. If the incline level decreases down to 0% and the
actual user’s pulse is still greater than 85% of the max. heart rate then the speed will be decreased by 0.5 mph /0.8 km/h every 30
seconds.
38
YOWZA JUNO TREADMILL
http://www.yowzafitness.com/
39
40
YOWZA JUNO TREADMILL