Venmar VJ71130SS Installation manual

INSTALLATION INSTRUCTIONS
HB0124
VJ71130SS CHIMNEY RANGE HOOD
! INTENDED FOR DOMESTIC COOKING ONLY !
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 10 AND 11.
Venmar Ventilation Inc., 550 Lemire Blvd., Drummondville QC J2C 7W9
1-800-567-3855
REGISTER YOUR PRODUCT ONLINE AT: www.bnv.ca
For additional information - visit www.venmar.ca
20083 rev. 03
!
WARNING
!
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE
THE FOLLOWING*:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by
qualified personnel in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA) and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE) and the local code
authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with any solid-state speed control device.
8. To reduce the risk of fire, use only metal ductwork.
9. This unit must be grounded.
10. To provide protection against electric shock, connect to
properly grounded outlets only.
11. Never use the glass parts to lift or move the hood. Even after a
low intensity impact, tempered glass can be weakened without
breaking but can experience spontaneous breakage. In the
event of an impact, inspect glass thoroughly; do not handle if
there is any sign of defect. If broken, tempered glass falls out in
interlocking clumps. It can also, on occasion, break into large
shards rather than the classic tiny piece pattern. Tempered
glass surface may be hot.
12. When applicable local regulations comprise more
restrictive installation and/or certification requirements,
the aforementioned requirements prevail on those of this
document and the installer agrees to conform to these at his
own expenses.
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels —
This could cause a violent steam explosion.
4. Use an extinguisher ONLY if:
A. You own a Class ABC extinguisher and you know how to
operate it.
B. The fire is small and contained in the area where it started.
C. The fire department has been called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
4. Your hood motor has a thermal overload which will
automatically shut off the motor if it becomes overheated. The
motor will restart when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
5. The minimum hood distance above cooktop must not be less
than 26". For best capture of cooking impurities, the bottom
of the hood should be at a maximum of 30" above cooking
surface. For a gas range, the bottom of the hood MUST NOT
BE LESS than 30" above cooktop.
6. Two installers are recommended because of the large size and
weight of this unit.
7. To reduce the risk of fire and to properly exhaust air, be sure to
duct air outside — Do not exhaust air into spaces within walls
or ceiling or into attics, crawl space or garage.
8. Because of the high exhausting capacity of this unit, you
should make sure enough air is entering the house to replace
exhausted air by opening a window close to or in the kitchen.
9. Please read specification label on product for further
information and requirements.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan, filters or in exhaust ducts.
d) Use proper pan size. Always use cookware appropriate for the
size of the surface element.
2
TABLE OF CONTENTS
1.
2
3
4.
5.
6.
7.
8
9.
10.
11.
12.
13.
INSTALL DUCTWORK..............................................................................................................................................................4
MEASURE INSTALLATION ........................................................................................................................................................4
PREPARE INSTALLATION .........................................................................................................................................................5
WIRING INSTALLATION ...........................................................................................................................................................5
PREPARE HOOD LOCATION .....................................................................................................................................................6
INSTALL UPPER FLUE MOUNTING BRACKET .................................................................................................................................6
INSTALL ADAPTER/DAMPER .....................................................................................................................................................6
INSTALL HOOD .....................................................................................................................................................................7
GREASE FILTER ...................................................................................................................................................................8
LIGHT BULBS ...................................................................................................................................................................8-9
OPERATION ...................................................................................................................................................................... 10
CARE ........................................................................................................................................................................... 11
REPLACEMENT PARTS ......................................................................................................................................................... 12
WARRANTY
VENMAR JAZZ RANGE HOOD
1-YEAR LIMITED WARRANTY
Venmar Ventilation Inc. warrants to the original consumer purchaser of its products, that such products will be free from defects
in materials or workmanship for a period of one (1) year from date of original purchase. This warranty includes in-home service.
THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. VENMAR VENTILATION INC. WILL NOT BE HELD
RESPONSIBLE FOR ANY CLAIMS OVER THE ORIGINAL PURCHASE PRICE OF A VENMAR JAZZ RANGE HOOD, NOR HELD
RESPONSIBLE FOR SUBSEQUENT DAMAGE OR INCIDENT.
During this one-year period, Venmar Ventilation Inc. will, at its option, repair or replace, without charge, any product or part which is found
to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO BULBS, FUSE, FILTERS, DUCTS, ROOF
CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover a) normal maintenance and service
b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repairs made by other than
Venmar Ventilation Inc., or c) a faulty installation or installation contrary to recommended installation instructions.
Warranty service is to be completed by an authorized Service Center designated by Venmar Ventilation Inc. Where applicable, in-home
service will be made available only in areas where a contracted service provider offers service. If in-home service is not available, the
product will be repaired or replaced, at Venmar Ventilation Inc.’s discretion, by the nearest authorized service provider. The unit removal
and reinstallation works are under the customer responsibility, and Venmar Ventilation Inc. cannot be charged for them.
The duration of any implied warranty is limited to the 1-year period as specified for the express warranty. Some provinces do not allow
limitation on how long an implied warranty lasts, so the above limitation may not apply to you. VENMAR VENTILATION INC. OBLIGATION
TO REPAIR OR REPLACE AT VENMAR VENTILATION INC. OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE
REMEDY UNDER THIS WARRANTY. VENMAR VENTILATION INC. SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. SOME PROVINCES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights and you may also have other rights, which vary from one province to another. This warranty
supersedes all prior warranties. To contact Venmar Ventilation Inc. Warranty Service call 1-800-567-3855 (in Canada). In order to qualify
for a warranty claim, the owner of a Venmar Jazz range hood must have the model and serial number along with a proof of the original
purchase date. At the time of requesting service, describe the nature of any defect in the product or part.
Venmar Ventilation Inc., 550 Lemire Blvd., Drummondville, Quebec CANADA J2C 7W9
Tel.: 1-800-567-3855 Fax: 819-475-2660
www.venmar.ca
3
1. INSTALL DUCTWORK
!
WARNING
When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
ROOF CAP
6" ROUND DUCT
Plan where and how the ductwork will be installed.
A straight, short duct run will allow the hood to perform most efficiently. Long duct
runs, elbows and transitions will reduce the performance of the hood. Use as few
of them as possible. Larger ducting may be required for longer duct runs.
Install wall or roof cap. Connect round metal ductwork to cap and work back
towards the hood location. Use 2" metal foil duct tape to seal the joints.
DECORATIVE FLUE
6" ROUND ELBOW
WALL CAP
HOOD
26" MINIMUM ABOVE
COOKING SURFACE
(30" FOR GAS RANGE)
HH0193A
2. MEASURE INSTALLATION
HOOD
14½" TO
CENTER OF
MOUNTING
HOLES
The minimum hood distance above cooktop MUST NOT BE less than 26".
A maximum of 30" above cooktop is highly recommended for best capture
of cooking impurities.
For a gas range, the bottom of the hood MUST NOT BE LESS than 30"
above cooking surface.
CEILING HEIGHT
8 feet
9 feet
10 feet
MIN. HOOD DISTANCE ABOVE COOKTOP MAX. HOOD DISTANCE ABOVE COOKTOP
26"
30"
30"
30"
26" MINIMUM ABOVE
COOKING SURFACE
(30" FOR GAS RANGE)
Distances over 30" are at the installer and users discretion; providing that ceiling
height permit.
STANDARD 36" H.
COOKTOP
HH0194A
4
3. PREPARE INSTALLATION
NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the retailer.
Make sure that the following items are included:
-
Hood
Curved glass panels (installed on the hood)
Micromesh filter
Decorative flue assembly (lower and upper flues)
Lower flue mounting bracket
Upper flue mounting bracket
6" Round adapter/damper
Installation instructions
Parts bag: 4 x no. 8 x 1¼" mounting screws, 4 x no. 8 x 1½" mounting screws, 10 x no. 8 x 7/16" mounting screws, 8 drywall anchors.
NOTE: If need be, discard extra screws.
Parts sold separately:
- Ducts, elbows, wall and roof caps.
NOTE: During installation, protect countertop and/or cooktop.
4. WIRING INSTALLATION
!
WARNING
Electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards. This
range hood must be properly grounded. Turn off electrical power at service entrance before wiring.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an
escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must
be plugged into an outlet that is properly installed and grounded.
Set the electrical power supply within the space covered by the decorative flue.
!
WARNING
Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions
are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an
extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.
337∕16"
MAX.
Position the outlet offset so that the power cord will not
interfere with the round duct. Place the outlet at a maximum
distance of 337/16" from where the cord exits from the
hood (see illustration at right). Make sure this does not
interfere with a mounting bracket fastening area or with the
decorative flue (where the flue touches the wall).
HE0158
5
5. PREPARE HOOD LOCATION
!
WARNING
• When cutting or drilling into wall, do not damage electrical wiring and other hidden utilities.
• When building framework, always follow all applicable construction codes and standards.
WALL STUDS
FRAMING BEHIND
1. Construct wood wall framing that is flush with surface of wall studs.
DRYWALL
Ensure:
a) The framing is centered over installation location and is sturdy
enough to support the weight of the hood.
b) The height of the framing will allow the hood to be secured to the
framing within the required height above cooktop (26" to 30").
2. Finish wall surface.
HD0506A
39½" = BOTTOM OF HOOD 26" ABOVE COOKTOP
43½" = BOTTOM OF HOOD 30" ABOVE COOKTOP
6. INSTALL UPPER FLUE MOUNTING BRACKET
CEILING
CENTER OF INSTALLATION
Center the bracket over the hood location and place it flush with the
ceiling. Make sure that the slots of the upper flue bracket point down. Use
the upper flue mounting bracket as a template to mark the position of its
screws.
Drill both screw holes using a 5/16" drill bit. Insert the included drywall
anchors into the drilled holes (one per hole).
Secure the upper flue bracket to the wall using 2 no. 8 x 1½" mounting
screws. Make sure that the bracket is tight against the wall.
UPPER FLUE MOUNTING
HD0247
BRACKET SLOTS
7. INSTALL ADAPTER/DAMPER
Install 6" round adapter/damper on top of the hood using 4 no. 8 x 7/16" mounting screws.
HO0209
6
CL
MOUNTING BRACKET
FLUSH WITH CEILING
8. INSTALL HOOD
!
WARNING
Be careful when installing the decorative flue and hood, they may have sharp edges.
CAUTION
DO NOT REMOVE the protective plastic film covering the decorative flue (upper and lower) and the hood yet.
1. Place the hood at its location. Using a pen, mark the position of both keyholes narrow end as well as the position of both additional
holes (Fig. 1). Remove the hood and install 2 no. 8 x 1¼" mouting screws at keyholes locations, leaving a 1/8" gap. Place the hood
on the wall and slide it in position. Verify that the hood is centered and leveled. Secure the hood by tightening the screws completely.
Install 1 no. 8 x 1¼" mouting screw in each additional hole (2).
2. Remove protective plastic film covering the lower flue only.
3. If possible (when space is sufficent): Install the lower flue bracket to its flue using 2 no. 8 x 7/16" mounting screws, ensure that the slots
point up (Fig. 2).
4. Carefully place both flues on top of the hood.
NOTE: Slightly slide up the upper flue to avoid damaging it.
5. Slide a 6" steel round duct over the adapter/damper. Use metal foil duct tape to seal the joint.
6. Plug hood power cord into the outlet.
7. Slide up the upper flue until it is aligned with its mounting bracket. The bracket must be inside the flue. Secure the upper flue to its
bracket using 2 no. 8 x 7/16" mounting screws (Fig. 3 and 4).
8. Remove protective plastic film covering the upper flue and the hood.
Fig. 2
Fig. 1
LOWER FLUE MOUNTING BRACKET
BACK VIEW
KEYHOLES LOCATION (Ø 5/16" TYP.)
ADDITIONAL
HOLES LOCATION
(Ø 5/16" TYP.)
LOWER
FLUE
BACK OF THE HOOD
SLOTS UP
HD0504A
HO0114
UPPER FLUE MOUNTING BRACKET
FRONT VIEW
Fig. 4
Fig. 3
UPPER FLUE
MOUNTING BRACKET
UPPER
LOWER FLUE
FLUE
HO0104
HO0035
7
9. GREASE FILTER
To remove grease filter, open the hood front panel (A), then remove
the grease filter by pressing down on its metal latch tab and tilting filter
downward (B).
To reinstall grease filter, align filter tabs with slots in the hood. Press down
the metal latch tab, push filter into position and release. Make sure the
filter is securely engaged after installation. Close the hood front panel.
B
A
HD0503
10. LIGHT BULBS
!
WARNING
• Before servicing or cleaning unit, switch power off at service panel and lock service disconnecting means to
prevent power from being switched on accidentally.
• Never use the glass parts to lift or move the hood. Even after a low intensity impact, tempered glass can be
weakened without breaking but can experience spontaneous breakage. In the event of an impact, inspect glass
thoroughly; do not handle if there is any sign of defect. If broken, tempered glass falls out in interlocking
clumps. It can also, on occasion, break into large shards rather than the classic tiny piece pattern. Tempered
glass surface may be hot.
This range hood requires two 3 W LED bulbs
(included).
To replace light assembly:
1. Remove curved glass panel 4 retaining screws. Set
panel and screws aside.
HD0505
8
10. LIGHT BULBS (CONT’D)
C
2. Unplug bulb assembly harness (C).
HO0212
3. Squeeze both springs (D) and push light assembly down (E).
Remove light assembly from hood and discard.
D
E
HO0211
4. Install new light assembly by reversing steps 3 to 1.
CAUTION
• When reinstalling, the curved glass panel retaining screws must be hand tighten only to prevent glass breakage.
• Ensure not to pinch wires when reinstalling the curved glass panel.
9
11. OPERATION
Always turn your hood on before you begin cooking to establish an air flow in the kitchen.
Let the blower run for a few minutes to clear the air after you turn off the range. This will help
keep the whole kitchen cleaner and brighter.
1
NOTE: When pressed, the chosen push button beeps and its indicator lights up blue.
1. LIGHTING PUSH BUTTON:
Press the Lighting push button once to turn the lights on. Press once more to turn the
lights off.
2
2. LED PUSH BUTTON:
Press the LED push button to turn the LEDs ON to 1 of the 4 following preprogrammed
colors:
Press once for blue, twice for green, three times for red, four times for white. Press once
more to turn the LEDs off.
OR
3
Press and hold the LED push button for 3 seconds to activate the color transition mode.
NOTE: If desired, during the color transition mode, press the LED push button once to
stop the transition and therefore select a particular color. (The hood is not able to
memorize the chosen color for further use.)
4
Press the LED push button once more to resume the color transition mode.
Press and hold the LED push button for 3 seconds to turn the LEDs off.
HC0067
3. BLOWER ON/SPEED INCREASE PUSH BUTTON (DOUBLE FUNCTION PUSH BUTTON):
Press the Blower ON/Speed increase push button to activate the blower at low speed.
Press twice for medium speed and once more for high speed.
NOTE: When blower is turned on, 100% of power level is activated during 1 to 2 seconds
acting as a “kick-start”. It will then operate at the desired setting.
4. BLOWER OFF/SPEED DECREASE PUSH BUTTON (DOUBLE FUNCTION PUSH BUTTON):
Press the Blower OFF/Speed decrease push button to lower the blower speed. If need be,
press until the blower stops.
10
1) Lighting push button
2) LED push button
3) Blower ON/Speed increase push button
4) Blower OFF/Speed decrease push button
12. CARE
Grease Filter
Grease filter should be cleaned monthly. Remove grease filter by pressing down on its metal latch tab. This will disengage the filter from
the hood. Tilt the filter downward and remove. Use a warm detergent solution to clean the filter. Let it dry and reinstall it.
Grease filter is dishwasher safe. Clean all-metal filter in the dishwasher using a non-phosphate detergent. Discoloration of the filter may
occur if using phosphate detergent or as a result of local water conditions — but this will not affect filter performance. This discoloration is
not covered by the warranty.
Blower Cleaning
Open the hood front panel and remove the filter in order to access the blower. Vacuum blower to clean. Do not immerse in water.
Hood Cleaning
Stainless Steel Cleaning:
Do:
Don’t:
• Regularly wash with clean cloth or rag soaked with warm water
and mild soap or liquid dish detergent.
• Use any steel or stainless steel wool or any other scrapers to
remove stubborn dirt.
• Always clean in the direction of original polish lines.
• Use any harsh or abrasive cleansers.
• Always rinse well with clear water (2 or 3 times) after cleaning.
Wipe dry completely.
• Allow dirt to accumulate.
• You may also use a specialized household stainless steel
cleaner.
• Let plaster dust or any other construction residues reach the
hood. During construction/renovation, cover the hood to make
sure no dust sticks to stainless steel surface.
Curved glass panels:
Hot water with mild soap or glass cleaner is all that is usually needed.
When using mild soap, rinse with clear water. Wipe dry with a clean, soft cloth to avoid water marks.
Avoid when choosing a detergent:
- Any cleaners that contain bleach will attack stainless steel.
- Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.
- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be
used close to a range.
11
13. REPLACEMENT PARTS
1
10
2
3
REPLACEMENT PARTS AND REPAIRS
4
9
8
5
6
7
HL0202
KEY
NO.
1
2
3
4
5
6
7
8
9
10
*
20380
SV08487
20375
20386
07243
20368
20384
20371
20374
20379
20083
*
20377
PART NO.
In order to ensure your ventilation unit
remains in good working condition,
you must use Venmar Ventilation
Inc. genuine replacement parts only.
Venmar Ventilation Inc. genuine
replacement parts are specially
designed for each unit and are
manufactured to comply with all the
applicable certification standards and
maintain a high standard of safety.
Any third party replacement part
used may cause serious damage and
drastically reduce the performance
level of your unit, which will result in
premature failing. Venmar Ventilation
Inc. also recommends to contact a
Venmar certified service depot for all
replacement parts and repairs.
DESCRIPTION
BRACKET KIT (SET OF 2)
ADAPTER/DAMPER
MOOD LIGHTING KIT (SET OF 2)
CURVED GLASS PANEL (SET OF 2)
MOTOR/BLOWER ASSEMBLY
LED LIGHT ASSEMBLY (SET OF 2)
MICROMESH FILTER
CONTROL INTERFACE
PC BOARD
DECORATIVE UPPER AND LOWER FLUES
INSTALLATION MANUAL
PARTS BAG INCLUDING:
4 X NO. 8 X 1¼" MOUNTING SCREWS, 4 X NO. 8 X 1½" MOUNTING SCREWS,
10 X NO. 8 X 7/16" MOUNTING SCREWS, 8 DRYWALL ANCHORS
* NOT SHOWN.
12
QUANTITY
1
1
1
1
1
1
1
1
1
1
1
1