Installation and
Operation Manual
ID
O
V EN
Y
T K
N O
A R
R B
R L
A EA
W S
IF
GX2-PSAC10D-R
Power Supply
P
2-
0 pp
-0 r Su
01 we
-0 Po
C
41D-R
00
88C10
00
0
52 SA
30
X
G
0
66
P
A
06
E
ly
E9
C
00
X0
669
USE ONLY WITH 250V FUSES
M
IN O
50/ PU DE L
60 T: 11 :
Hz 5/2 G X
4.5 30V 2 -P
/2.3 ~
A OU SAC
TP 10
UT: D
1 -R
5.1 2V
V
P
1 RO
17.9 6.1A DUC
AM MA TO
AX X. 3 F PH
. M .7V ILIP
AX
. PO 1 PINE
WE 9.2A S
R:3 M
00W AX
.
D
BE ISCOCAU
FO N
U RE NE TIO
CHNIT FREMCT PO N
AS RO OV W
SIS M IN ER
G
86
24
9
-G X
2
R
E1
AIH
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Caution
These servicing instructions are for use by qualified personnel only. To reduce the risk of electrical shock, do not perform any servicing other
than that contained in the Installation and Troubleshooting Instructions unless you are qualified to do so. Refer all servicing to qualified service
personnel.
Special Symbols That Might Appear on the Equipment
This symbol indicates that dangerous voltage levels are present within the equipment. These voltages are not
insulated and may be of sufficient strength to cause serious bodily injury when touched. The symbol may also
appear on schematics.
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important
installation, servicing, and operating instructions in the documents accompanying the equipment.
For continued protection against fire, replace all fuses only with fuses having the same electrical ratings
marked at the location of the fuse.
This symbol indicates a hot surface. Use caution before touching a surface marked with this symbol.
This equipment operates over the marked Voltage and Frequency range without requiring manual setting of any
selector switches. Different types of line cord sets may be used for connections to the mains supply circuit and should
comply with the electrical code requirements of the country of use. This equipment requires a grounding conductor in
the line cord. The line cord provided with the equipment is acceptable for use with NEMA Style 5-15R ac receptacles
supplying nominal 120 Volts.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE APPARATUS
SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS SHALL BE PLACED ON THE
APPARATUS.
CAUTION: TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE RECOMMENDED POWER CABLES.
CAUTION: SURFACE MAY BE HOT. DISCONNECT POWER AND ALLOW SURFACE TO COOL BEFORE TOUCHING.
It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device is connected. This is to avoid damaging the
equipment by local lightning strikes and other electrical surges.
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Installation
Manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own expense.
Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Canadian Compliance
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respects toutes les exigences du Règlement sur le matériel brouilleur du Canada.
International Declaration of Conformity
We
Motorola, Inc.
101 Tournament Drive
Horsham, PA 19044, U.S.A.
declare under our sole responsibility that the
OmniStar®
Model GX2-PSAC10D-R
to which this declaration relates is in conformity with one or more of the following standards:
EMC Standards
EN55022
EN55024
EN55013
EN50083-2
CISPR-22
CISPR-24
CISPR-13
EN60825
EN50083-1
EN60950
IEC 60950 + A1: 1992 + A2: 1993 + A3: 1995 + A4: 1996
IEC60065
Safety Standards
EN60065
following the provisions of the Directive(s) of the Council of the European Union:
EMC Directive 89/336/EEC
Low Voltage Directive 73/23/EEC
WARNING
There is an energy hazard on this built-in power supply. During operation, the operator must not touch the
+12V output.
This unit contains a secondary output exceeding 240VA. When installing into the end system, care must be
taken not to touch the +12V output.
Copyright © 2007 by Motorola, Inc.
All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as
translation, transformation or adaptation) without written permission from Motorola, Inc.
Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola
to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed,
including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or
changes in the product(s) described in this manual at any time.
MOTOROLA, the Stylized M Logo, and OmniStar are registered in the US Patent & Trademark Office. All other product or service names are
the property of their respective owners. © Motorola, Inc. 2007
Contents
Section 1
Introduction
Using This Manual ........................................................................................................................................................................... 1-2
Related Documentation................................................................................................................................................................... 1-2
Document Conventions................................................................................................................................................................... 1-2
If You Need Help............................................................................................................................................................................... 1-3
Calling for Repairs ........................................................................................................................................................................... 1-4
Section 2
Overview
Redundancy...................................................................................................................................................................................... 2-3
Section 3
Installation and Operation
Unpacking......................................................................................................................................................................................... 3-1
Installation ........................................................................................................................................................................................ 3-1
Powering ........................................................................................................................................................................................... 3-2
Operation .......................................................................................................................................................................................... 3-2
Fault Reporting................................................................................................................................................................................. 3-3
Appendix A
Specifications
Input Power.......................................................................................................................................................................................A-1
Output Power....................................................................................................................................................................................A-1
Physical Properties..........................................................................................................................................................................A-1
Environmental ..................................................................................................................................................................................A-1
Appendix B
Menus
Module Status Menu ........................................................................................................................................................................B-1
Module Info Menu.............................................................................................................................................................................B-2
Alarms ...............................................................................................................................................................................................B-2
Abbreviations and Acronyms
GX2-PSAC10D-R Installation and Operation Manual
ii
Contents
Figures
Figure 1-1 GX2-PSAC10D-R............................................................................................................................................................1-1
Figure 2-1 GX2-HSG* fully populated .............................................................................................................................................2-1
Figure 2-2 GX2-PSAC10D-R front view..........................................................................................................................................2-2
Figure 2-3 GX2-PSAC10D-R top view ............................................................................................................................................2-2
Figure 2-4 GX2-PSAC10D-R rear view ...........................................................................................................................................2-3
Figure 3-1 GX2-PSAC10D-R............................................................................................................................................................3-1
Figure 3-2 AC input connector .......................................................................................................................................................3-2
Figure 3-3 GX2-PSAC10D-R block diagram ..................................................................................................................................3-2
Tables
Table 3-1 LED fault indication ........................................................................................................................................................3-3
Table B-1 GX2-PSAC10D-R menus ............................................................................................................................................... B-1
GX2-PSAC10D-R Installation and Operation Manual
Section 1
Introduction
The OmniStar® GX2 is a fiber optic broadband transmission platform for headend and hub locations
that supports advanced hybrid-fiber coax telecommunications systems. The GX2 series is a complete
line of headend fiber optic products designed to transport video and data signals in CATV systems
and related applications. The OmniStar GX2 system is flexible in its application and includes a series
of modules and options that you can select to accommodate system requirements.
The GX2 system offers a solution for the next generation of broadband network applications where
its requirements for smaller node sizes, deployment of point-to-point lasers, and return-path
applications optimize operating space. Its high module density enables network operators to install
more equipment in less space. The wide operational bandwidth of the platform enables you to offer
more revenue-generating services.
This manual describes the GX2-PSAC10D-R power supply that provides power for the equipment
shelf (GX2-HSG*) and all application modules.
The GX2-PSAC10D-R features include:
ƒ
Regulated +5.1, +12, and +3.7 VDC to the equipment shelf backplane
ƒ
Integrated fans for localized cooling
ƒ
Dual power supply option (AC or DC) for load sharing and/or redundancy
ƒ
Microprocessor control and monitoring of critical functions
ƒ
Tri-colored LED for module status indication
ƒ
Wide operating temperature range from –20°C to +60°C
ƒ
Downloadable firmware
ƒ
True Plug-n-Play operation
ƒ
Restriction of Hazardous Substances (RoHS) compliant
Figure 1-1 illustrates a rear view of the GX2-PSAC10D-R:
F igu re 1-1
GX2-PSAC10D-R
USE ONLY WITH 250V FUSES
GX2-PSAC10D-R Installation and Operation Manual
1-2
Introduction
Using This Manual
The following sections provide information and instructions to install the GX2-PSAC10D-R:
Section 1
Introduction provides a product description, related documentation, the technical
helpline, and repair/return information.
Section 2
Overview provides an overview of the GX2 system and a functional description of the
GX2-PSAC10D-R.
Section 3
Installation and Operation provides instructions on how to install the GX2-PSAC10D-R
and verify that it is operating properly.
Appendix A
Specifications provides general specifications for the GX2-PSAC10D-R.
Appendix B
Menus provides the GX2-PSAC10D-R menu structure and information on how to use
the optional SDU with display.
Abbreviations
and Acronyms
The Abbreviations and Acronyms list contains the full spelling of the short forms used
in this manual.
Related Documentation
The following documents provide information that is required for products that can be used with the
GX2-PSAC10D-R:
„
GX2-CM100B Control Module Installation and Operation Manual
„
GX2-PSDC10D-R DC Power Supply Installation and Operation Manual
„
GX2-HSG* Equipment Shelf Installation Manual
There are additional documents that provide information that may be of interest to you. These
documents are specific to each GX2 application module and are shipped with the product.
Document Conventions
Before you begin using the GX2-PSAC10D-R, familiarize yourself with the stylistic conventions
used in this manual:
SMALL CAPS
Denotes silk screening on the equipment, typically representing front- and rear-panel
controls, input/output (I/O) connections, and light emitting diodes (LEDs)
* (asterisk)
Indicates that several versions of the same model number exist and the information
applies to all models; when the information applies to a specific model, the complete
model number is given
Italic type
Denotes a displayed variable, a variable that you must type, or is used for emphasis
GX2-PSAC10D-R Installation and Operation Manual
Introduction
1-3
If You Need Help
If you need assistance while working with the GX2-PSAC10D-R, contact the Motorola Technical
Response Center (TRC):
ƒ
Toll-free: 1-888-944-HELP (1-888-944-4357) Outside the U.S.: 1-215-323-0044
ƒ
Direct: 1-847-725-4011
ƒ
Motorola Online: http://businessonline.motorola.com
The TRC is on call 24 hours a day, 7 days a week. In addition, Motorola Online offers a searchable
solutions database, technical documentation, and low-priority issue creation and tracking. For
specific toll-free numbers when calling from outside the United States, please refer to your product
manual or our Web page.
Technical Response Center
Telephone Menu Options
Connected Home Solutions
http://businessonline.motorola.com
888-944-HELP / 215-323-0044
Broadcaster,
Satellite IRD or
Encoder Products
PRESS 2
Video Products
PRESS 1
PRESS 1
Controllers
PRESS 1
Digital
PRESS 2
Headend
PRESS 2
Uplink
Encoder
PRESS 1
Commercial
IRD
PRESS 3
Set-tops
PRESS 2
Analog
Consumer
Products
PRESS 4
Data Networks/
Transmission Products
PRESS 3
PRESS 3
PRESS 2
PRESS 1
Cable Router Cable Modems Transmission
Products
VOIP
Products
Severity Level
1 - Critical Failure
2 - Serious Failure
3 - Lesser Failure
4 - Technical Assistance
PRESS 4
Network
Management
PRESS 5
Multiservice
Transport
Products
(MBT/MWT/MEA)
PRESS 1
Consumer
Satellite
C Band
PRESS 2
Broadband
Retail
Support
PRESS 2
PRESS 1
Network
Network
Licensing Management
Products
Issued: 04/2005
GX2-PSAC10D-R Installation and Operation Manual
1-4
Introduction
Calling for Repairs
If repair is necessary, call Motorola’s Repair Facility at 1-800-227-0450 for a Return for Service
Authorization (RSA) number before sending the unit. The RSA number must be prominently
displayed on all equipment cartons. The Repair Facility is open from 8:00 AM to 5:00 PM Central
Time, Monday through Friday..
When calling from outside the United States, use the appropriate international access code, and then
call 956-541-0600 to contact the Repair Facility.
When shipping equipment for repair, follow these steps:
1
Pack the unit securely.
2
Enclose a note describing the exact problem.
3
Enclose a copy of the invoice that verifies the warranty status.
4
Ship the unit PREPAID to the address indicated on the RSA form provided by Motorola.
GX2-PSAC10D-R Installation and Operation Manual
Section 2
Overview
The OmniStar GX2 platform provides increased rack density, reliability, ease of operation, and
computer-aided troubleshooting through the extensive use of status monitoring. Low time-to-repair
is facilitated because application modules are accessible and replaceable from the front of the
OmniStar GX2 equipment shelf. Fiber connections are also located in the front while RF and power
connections are located on the rear of the equipment shelf.
Basic components of the OmniStar GX2 system include:
ƒ
Equipment shelf model GX2-HSG*
ƒ
Control module GX2-CM100B
ƒ
Power supply module GX2-PSAC10D-R or GX2-PSDC10D-R
ƒ
A series of application modules to fit any system requirement
Figure 2-1 illustrates a front view of a fully populated GX2-HSG*:
Figure 2-1
GX2-HSG* fully populated
The GX2-PSAC10D-R provides +5.1, +12, and +3.7 VDC power to the GX2-HSG* and all
application modules. The auto-sensing input-voltage feature recognizes 115 VAC or 230 VAC
applications. Surge protection for the input plus overcurrent protection for the output provide the
necessary safeguards for the power supply and the application modules served by it. A large heatsink
and integrated fans dissipate the internally generated heat and keep the module temperature within
acceptable limits.
GX2-PSAC10D-R Installation and Operation Manual
2-2
Overview
Figure 2-2 illustrates a front view of the GX2-PSAC10D-R:
Figure 2-2
G X 2 - P S AC 1 0 D - R f r o n t vi ew
Figure 2-3 illustrates a top view of the GX2-PSAC10D-R:
Figure 2-3
G X 2 - P S AC 1 0 D - R t o p vi ew
CAUTION
Surface may be hot. Disconnect power and allow surface to cool before
touching.
GX2-PSAC10D-R Installation and Operation Manual
Overview
2-3
Figure 2-4 illustrates a rear view of the GX2-PSAC10D-R:
Figure 2-4
G X 2 - P S AC 1 0 D - R r e a r vi ew
IEC
LED
connector
Thumbscrews
Redundancy
The unused compartment on the bottom of the GX2-HSG* can be used for redundant powering with
the purchase of a second power supply. For redundancy, it is possible to use two GX2-PSAC10D-R's
(as shown in Figure 3-1), two GX2-PSDC10Cs, or any combination of GX2-PS*10* power supplies.
To provide load sharing in addition to redundancy, you must use two power supplies with model
numbers ending in the same letter suffix. The exception to this rule is that models ending in “D-R”
will load share with models ending in “C”. If one power supply fails, the other assumes the entire
load.
GX2-PSAC10D-R Installation and Operation Manual
Section 3
Installation and Operation
This section provides instructions to install the GX2-PSAC10D-R power supply in the GX2-HSG*
and verify its operation.
Unpacking
Unpack the GX2-PSAC10D-R and inspect it for damage. If damage is visible, set it aside in the
original packing material and contact the Motorola Customer Service Department for further
instructions.
Record the model number, serial number, and related information for future reference.
Installation
To operate, the GX2-HSG* must be equipped with a GX2-PSAC10D-R or GX2-PSDC10D-R power
supply. To install the GX2-PSAC10D-R power supply:
1
Rotate the power supply so that the cooling fans face you and the external power connection is
on the left.
2
Position the power supply into the left- or right-side power supply compartment on the rear of
the GX2-HSG* as illustrated in Figure 3-1:
Figure 3-1
G X 2 - P S AC 1 0 D - R
3
Insert the power supply completely into the chassis ensuring that connection is made with the
backplane connectors.
4
Secure the power supply by tightening the two captive thumbscrews into the GX2-HSG*.
5
Plug the IEC connector end of the ac power cord into the rear of the GX2-PSAC10D-R.
GX2-PSAC10D-R Installation and Operation Manual
3-2
Installation and Operation
Powering
After all connections, including fiber, have been established, apply power to the GX2-HSG*. Power
connections are in the rear of the equipment shelf as illustrated in Figure 3-1.
Using the supplied cable, provide power from a source voltage of 105 VAC to 264 VAC to the AC
input connector on the rear of the GX2-PSAC10D-R as illustrated in Figure 3-2:
Figure 3-2
AC i n p u t c o n n e c t o r
Before removing a power supply from the GX2-HSG*, disconnect the power input cable from the
rear of the GX2-PS*10*. If a GX2-PS*10* is removed before power is disrupted, you must wait
approximately five minutes before restoring power or the unit may not start properly.
In normal operation, it is not necessary to remove power from the equipment shelf when installing a
new module or replacing one. The shelf and all modules are designed to enable module replacement
with power applied.
Operation
The AC input voltage, which must be between 105 Vrms and 264 Vrms, is filtered and then applied
to a power-factor control circuit that converts the AC voltage to DC. The high voltage DC is applied
to three DC/DC converters. The converters, one for each of the three output voltages, supply
precisely regulated output voltages of +5.1, +12, and +3.7 VDC respectively. Short circuit protection
is provided by each of the DC/DC converters to limit the output current until the fault is cleared.
Figure 3-3 illustrates a block diagram of the GX2-PSAC10D-R:
Figure 3-3
G X 2 - P S AC 1 0 D - R b l o c k d i a g r a m
GX2-PSAC10D-R Installation and Operation Manual
Installation and Operation
3-3
Fault Reporting
Each output voltage and the internal voltage of the supplies is monitored. The temperature of the
incoming air, the heat sink, and fan operation are monitored as well. In the event of a fan failure, a
major alarm is sent to the GX2-CM100B control module and the local LED glows red. The
monitored signals are all compared to their appropriate internal specification. When a deviation
occurs, either a minor or major alarm is sent to the control module, and the appropriate LED color on
the GX2-PSAC10D-R illuminates.
Table 3-1 lists the possible LED colors and the probable fault indication:
Table 3-1
LED fault indication
LED color
Fault Indication
Green
Power is applied and all measured parameters are within tolerance.
Yellow
A minor alarm is detected, however, the GX2-PSAC10D-R is not rendered
inoperative.
Red
A major alarm is detected and immediate intervention is required.
Not lit
If the LED is not lit, verify that system power is available.
The GX2-PSAC10D-R also includes non-volatile memory to store module identity information that
includes model number, serial number, and manufacturing date code. To access this information, the
GX2-CM100B Control Module must be installed in the GX2-HSG*. Data from the
GX2-PSAC10D-R is reported to the GX2-CM100B and is accessible through the GX2-SDU or the
Ethernet port on the front panel. Using the GX2-SDU, or a network management system, you can
identify the cause of a fault in the GX2-PSAC10D-R. Refer to Appendix B, Menus, for information
regarding the SDU menu structure.
The GX2-CM100B front panel also contains two tri-colored LEDs identified as PS1 and PS2. These
LEDs give the same indication as identified in Table 3-1. If the PS1 or PS2 LED is not lit, then a
power supply is not installed or the installed power supply is not functional.
If one power supply fails in a redundant application, you can still access the failed power supply
through the SDU or EMS. This is possible as the microprocessor on each power supply is powered
from the backplane voltage rather than internally from the power supply.
GX2-PSAC10D-R Installation and Operation Manual
Ap pen dix A
Specifications
Specifications for the GX2-PSAC10D-R are valid over the given operating temperature range. Refer
to the current Motorola BCS product catalog for additional information not provided in this section.
Input Power
AC input voltage
105 Vrms to 264 Vrms
AC current
At 115 V
At 230 V
4.0 amps rms maximum with full load
2.0 amps rms maximum with full load
Power consumption
420 watts maximum with full load
Efficiency
68% at maximum load
Fusing
Two 10 amp slow blow at power input connector
Output Power
Output voltage
+5.1 VDC range
+12 VDC range
+3.7 VDC range
5.05 to 5.15 VDC nominal with maximum load at +25°C
11.88 to 12.12 VDC nominal with maximum load at +25°C
3.66 to 3.75 VDC nominal with maximum load at +25°C
Output current
+5.1 VDC range
+12 VDC range
+3.7 VDC range
17.9 amps maximum with maximum load at +25°C
16.1 amps maximum with maximum load at +25°C
19.2 amps maximum with maximum load at +25°C
Maximum total output
power
300 Watts
Physical Properties
Dimensions
2.2” H x 7.7” W x 11.7” D (5.6 cm x 19.6 cm x 29.7 cm)
Weight
8.0 lb (3.6 kg)
Mounting
GX2-HSG*
Environmental
Operating temperature
range
-20°C to +60°C (-4° to +140°F)
Storage temperature
range
-40°C to +85°C (-40° to +186°F)
GX2-PSAC10D-R Installation and Operation Manual
Ap pen dix B
Menus
This appendix provides information about:
ƒ
Using the optional SDU with display to access GX2-PSAC10D-R menus
ƒ
The menu structure
ƒ
Alarms
Table B-1 identifies the procedure for navigating through the GX2-PSAC10D-R menus using the
optional SDU with display:
Table B-1
G X 2 - P S AC 1 0 D - R m e n u s
To
Use
Scroll to the top-level
power supply menu
Press the up or down arrows to scroll to the PS1 or PS2 menu. If a power
supply is not installed, EMPTY is displayed after the PS1 or PS2.
Enter a level two
menu from the
top-level PS1 or PS2
menu
Press the right arrow. Then press the up and down arrows to scroll to the
MODULE STATUS MENU or the MODULE INFO MENU.
Change a parameter
value
Press the right arrow to enter edit mode.
Use the up and down arrows to change the value.
Press ENTER to save the new value or press the left arrow to exit edit
mode without changing the value.
If you press no key for 10 to 15 seconds, you exit edit mode with the value
unchanged.
Go up from level two
to level one
Press the left arrow.
The following subsections provide the menu structure:
Module Status Menu
The italicized x’s in this table indicate a displayed variable:
Parameter
Value
AMBIENT TEMPERATURE:
xx.x °C
HEATSINK TEMPERATURE:
xx.x °C
BACKPLANE
+12 V:
+5.1 V:
+3.7 V:
xx.x V
x.x V
x.x V
GX2-PSAC10D-R Installation and Operation Manual
B-2
Menus
Module Info Menu
ALIAS>
User selected (default GX2-POWER SUPPLY)
MODEL:
GX2-PSAC10D-R
S/N:
0123456789ABCDEF
DATE CODE:
mmddyyyy
FW REV:
XX
HW REV:
XX
Alarms
The second line on the SDU can display any of the following messages when an alarm condition
exists:
FAN CURRENT ALARM
+12V BACKPLANE ALARM
+5.1V BACKPLANE ALARM
+3.7V BACKPLANE ALARM
AMBIENT TEMPERATURE ALARM
HEATSINK TEMPERATURE ALARM
BANK 0 BOOT ALARM
BANK 1 BOOT ALARM
FLASH ALARM
FACTORY CRC ALARM
ALARM CRC ALARM
MODEL NAME ALARM
POWER SUPPLY FAIL
GX2-PSAC10D-R Installation and Operation Manual
Abbreviations and Acronyms
The abbreviations and acronyms list contains the full spelling of the short forms used in this manual:
CATV
Community Antenna Television
dB
decibels
dBm
decibels referenced to one milliwatt
dBc
decibels relative to carrier level
dBmV
decibels referenced to one millivolt
ESD
electrostatic discharge
LED
light-emitting diode
MHz
Megahertz
mW
milliwatts
RF
radio frequency
RSA
Return for Service Authorization
TRC
Technical Response Center
TTR
time-to-repair
GX2-PSAC10D-R Installation and Operation Manual
Visit our website at:
www.motorola.com
538445-001-a
5/07