Installation
Instructions
T050.210
50
6
0
TRIM KIT for CENTRAL THERMOSTAT
with VOLUME CONTROL
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
ASSE 1016
M968418
ROUGHING-IN DIMENSIONS
5"
8-3/16"
100
1-3/4"
to 2-1/2"
3-1/8"
FINISHED
WALL
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
CARE INSTRUCTIONS:
To keep your new faucet looking new, please follow
these simple care instructions:
DO:
Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
Failure to follow these care instructions may
damage the Faucet's finish.
1
TRIM INSTALLATION
3
Push CAPS (1) onto TEMPERATURE-CONTROL KNOB (2)
and VOLUME-CONTROL KNOB (3) until fully seated.
1
4
Push on ESCUTCHEON (4) and attach with SCREWS (5)
to valve body.
5
2
2
1
HANDLE INSTALLATION
8
Push TEMPERATURE-CONTROL KNOB (1) with the red stop onto KNOB
MOUNT (2). Push RING (3) onto TEMPERATURE-CONTROL KNOB (1) and
attach with SCREW (4).
6
3
7
Push VOLUME-CONTROL KNOB (6) onto HANDLE ADAPTER (8). Push RING (3)
onto VOLUME-CONTROL KNOB (6) and and attach with SCREW (7).
5
50
6
0
Press on KNOB CAPS (5).
2
1
5
3
3
4
TEMPERATURE CALIBRATION
1
ARROW
"B"
Check that arrow marking B points vertically upwards. If not, push the BLACK
CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3)
and reinstall KNOB MOUNT (3) with arrow "B" pointing upwards.
SET HOT LIMIT STOP
The maximum mixed water temperature is set at 109 F at the factory.
This setting can be changed if desired.
4
Remove the TEMPERATURE LIMIT STOP (4) (H shaped Black Plastic part).
Reinstall it at the desired notch as indicated in the diagram to limit the maximum
mixed water temperature to 104 F or 112 F.
For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout
temperature is 100 F. Check that arrow marking A on the KNOB MOUNT (3) still points
upward after adjusting the thermostat to 100 F. If not, pull out the RED LOCKING DEVICE (5).
Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow.
Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards.
ARROW
"A"
104
3
109
112
2
5
Reinstall RED LOCKING DEVICE (5).
4
OPERATING THE VALVE
1
0
0
1
If a temperature over 100 F is desired, pull the RED STOP BUTTON (1) away from the body
of the MIXER UNIT and turn the TEMPERATURE KNOB.
This will increase the mixed water temperature up to the maximum limit previously
selected in step 3.
M968418
TRIM KIT for CENTRAL
THERMOSTAT
WITH VOLUME CONTROL
MODEL NUMBER
T050.210
907093 -YYY0A
CAP
953154-YYY0A
ESCUTCHEON
954026-YYY0A
VOLUME CONTROL HANDLE BASE
909750-YYY0A
HANDLE RING
918428-0070A
VOLUME CONTROL SCREW
907065-YYY0A
HANDLE CAP
918434-YYY0A
ESCUTCHEON SCREWS
913959-0070A
50
051313-YYY0A
TEMPERATURE
CONTROL HANDLE BASE
VOLUME CONTROL
HANDLE
0
6
SEAL
953976-YYY0A
909750-YYY0A
HANDLE RING
918416-0070A
TEMPERATURE SCREW
060441-YYY0A
TEMPERATURE
CONTROL HANDLE
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
CHROME
POLISHED BRASS
SATIN
CHR/POL. BRASS (MIXAGE)
002
099
295
299
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
M968418
Installation
Instructions
R540
XAM
CENTRAL THERMOSTAT
with VOLUME CONTROL
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
Certified to comply with ANSI A112.18.1M
ASSE 1016
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
ROUGHING-IN DIMENSIONS
VERTICAL
M968257
HORIZONTAL
1-3/4"
to 2-1/2"
1-3/4"
to 2-1/2"
13/16"
mixed
out
FINISHED
WALL
FINISHED
WALL
hot in
6-1/2"
2"
cold in
3-1/8"
2-3/16"
mixed
out
mixed
out
hot in cold in
mixed
out
13/16"
3-1/8"
2-13/16"
NOTE: ALL PORTS ARE 3/4 NPT
FEMALE. FITTING MUST BE INSTALLED
WITH VOLUME CONTROL ON TOP.
THERMOSTATIC BATH/
SHOWER INSTALLATION
USING A TWIN ELL, DIVERTER
SPOUT AND FIXED SHOWER
THERMOSTATIC SHOWER INSTALLATION
USING A DIVERTER VALVE, FIXED
SHOWER HEAD AND ADJUSTABLE HAND
HELD SHOWER
THERMOSTATIC SHOWER INSTALLATION USING A
DIVERTER VALVE, FIXED SHOWER HEAD, ADJUSTABLE
HAND HELD SHOWER, ON/OFF VALVE AND THREE
BODY SPRAYS
DIVERTER
VALVE
C/L
DIVERTER
VALVE
80"-86"
18"
ON/OFF
VALVE
SHOWER
PORT
MUST BE
PLUGGED
4"
TWIN
ELL
TOP OF TUB RIM
BOTTOM OF TUB
THERMOSTATIC VALVE INSTALLED
IN THE VERTICAL POSITION
IMPORTANT: WHEN NOT USING A
DIVERTER SPOUT A SEPARATE
DIVERTER VALVE MUST BE USED.
HOT COLD
3/4"
3/4"
HOT COLD
3/4"
3/4"
TUB PORT MUST
BE PLUGGED
TUB PORT MUST
BE PLUGGED
THERMOSTATIC VALVE INSTALLED
IN THE HORIZONTAL POSITION
THERMOSTATIC VALVE INSTALLED
IN THE HORIZONTAL POSITION
1
CAUTION
ROUGHING-IN THE VALVE
Turn off hot and cold water supplies
before beginning.
HOT
INLET
Decide on desired configuration.
Prepare water supplies per ROUGHING-IN DIMENSIONS.
CROSS
BRACE
COLD
INLET
Install VALVE at indicated height and depth.
Connect HOT water supply to inlet marked with the RED DOT and
COLD water supply to inlet market with the BLUE DOT.
VALVE
BODY
MAX
Assemble the CONNECTING PIPE to one of the MIXED OUTLETS of the VALVE.
Note: The tub port is fitted with a plug at the factory.
Important! Install any required shut off or diverter valves into the piping system.
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL
DAMAGE THE TEMPERATURE CONTROL ELEMENT.
Secure VALVE body to cross brace of wall structure.
WARNING
PLASTER
GUARD
SCREWS
2
FLUSHING THE VALVE
CAUTION
MIXED
OUTLET
PLASTER
GUARD
Turn off hot and cold water supplies
before beginning.
Water should be flushed through the piping to prevent
clogging of the Thermal Element.
Remove PLASTER GUARD (1).
Turn ADAPTER (2) on volume control clockwise until
it reaches the stop.
8
Remove CLUTCH COVER SCREWS (3) and CLUTCH COVER (4).
1
9a
XAM
Pull off ADAPTER (2).
Pull out CLUTCH DRIVE SHAFT (5).
7a
Loosen the SCREWS (6) in the center of the GEARS (7). Remove
the GEARS (7) and BACK PLATE (8).
6a
5
Remove the COLD CARTRIDGE (9) using a 22mm socket wrench.
Turn on MAIN COLD WATER SUPPLY to flush line.
PLASTER
GUARD
SCREWS
4
Reassemble COLD CARTRIDGE (9) and repeat flushing steps for
HOT side (9a).
Replace BACK PLATE (8). Assemble both GEARS (7) with the flat side
facing BACK PLATE (8) and tighten SCREWS (6).
3
9
2
7
IMPORTANT:
Close both CARTRIDGES (9, 9a) by rotating GEARS (7) counterclockwise.
6
Replace CLUTCH DRIVE SHAFT (5) and CLUTCH COVER (4) with SCREWS (3).
Turn VOLUME CONTROL HANDLE 180 to synchronize the
HOT and COLD CARTRIDGES.
Turn on water supply and check for leaks.
3
TEMPERATURE CALIBRATION
ARROW
"B"
Check that arrow marking B points vertically upwards. If not, push the BLACK
CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3)
and reinstall KNOB MOUNT (3) with arrow "B" pointing vertically upwards.
SET HOT LIMIT STOP
The maximum mixed water temperature is set at 109 F at the factory.
This setting can be changed if desired.
4
Remove the TEMPERATURE LIMIT STOP (4) (H shaped Black Plastic part).
Reinstall it at the desired notch as indicated in the diagram to limit the maximum
mixed water temperature to 104 F or 112 F.
For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout
temperature is 100 F. Check that arrow marking A on the KNOB MOUNT (3) still points
upward after adjusting the thermostat to 100 F. If not, pull out the RED LOCKING DEVICE (5).
Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow.
Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards.
1
ARROW
"A"
104
109
3
112
2
5
Reinstall RED LOCKING DEVICE (5).
M968257
CENTRAL THERMOSTAT
WITH VOLUME CONTROL
MODEL NUMBER
R540
923143-0070A
GEAR BOX
BACK PLATE
952550-0070A
VALVE KIT (HOT & COLD)
953156-0070A
GEAR/CLUTCH
WHEELS
953155-0070A
DRIVE SHAFT
923142-0070A
CLUTCH COVER
918327-0070A
CLUTCH COVER SCREWS
911940-0070A
GEAR BOX
SEALING WASHER
923348-0070A
HANDLE ADAPTER
954040-0070A
THERMOSTATIC
CONTROL
CARTRIDGE
953963-0070A
TEMPERATURE
HANDLE EXTENSION
953957-0070A
TEMPERATURE
CALIBRATION
ADJUSTMENT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
M968257