Wolf ICBDD30 Installation guide

DOWNDRAFT VENTILATION
INSTALLATION GUIDE
DOWNDRAFT VENTILATION
Contents
2Downdraft
Ventilation
3Specifications
4Installation
6Troubleshooting
Important Note
Product Information
To ensure this product is installed and operated as safely
and efficiently as possible, take note of the following types
of highlighted information throughout this guide:
Important product information including the model and
serial number are listed on the product rating plate. The
rating plate is located next to the blower housing on the
front side of the downdraft, below the countertop. Refer to
the illustration below.
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
Features and specifications are subject to change at any
time without notice. Visit wolfappliance.com/specs for the
most up-to-date information.
damage may occur if instructions are not followed.
If service is necessary, contact Wolf factory certified service
with the model and serial number.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
RATING PLATE
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
Installation work and electrical wiring must be
a)
done by qualified person(s) in accordance with
all applicable codes and standards, including
fire-rated construction.
b)Sufficient air is needed for proper combustion and exhausting of gases through the flue
(chimney) of fuel burning equipment to prevent
back drafting. Follow the heating equipment
manufacturer's guideline and safety standards,
and the local code authorities.
c)
When cutting or drilling into wall or ceiling, do
not damage electrical wiring and other hidden
utilities.
Rating plate location.
2
|
English
d)Ducted fans must always be vented to the
outdoors.
SPECIFICATIONS
Installation Requirements
Electrical
Downdraft
For installation with a Wolf cooktop, a minimum 638 mm
deep flat countertop is required.
Installation must comply with all applicable electrical codes
and be properly grounded (earthed).
INSTALLATION WITH COOKTOP
For installation with a sealed burner rangetop, an accessory
trim kit is required. Contact your authorized Wolf dealer for
details.
Locate the electrical supply as shown in the illustrations on
pages 3–4. A separate circuit, servicing only this appliance
is required. A ground fault circuit interrupter (GFCI) is not
recommended and may cause interruption of operation.
The remote-mounted control module can be positioned
horizontally or vertically. It must be located within 3 m of the
downdraft assembly and a minimum 76 mm from the edge
of the cooktop or rangetop cut-out.
W
DOWNDRAFT
CUT-OUT WIDTH
68 mm
E
Certain installations may require that the electrical supply
be placed in an adjacent cabinet.
210 mm*
COOKTOP CUT-OUT
ELECTRICAL REQUIREMENTS
BLOWERS
CAUTION
For use with Wolf 1014 m3/hr internal blower and
remote blowers rated maximum 3 amps.
Internal and remote blower assemblies are available through
your authorized Wolf dealer.
Internal blowers include a 152 mm round discharge, can be
front or rear mounted and can be discharged in any direction by rotating the blower box. Remote blowers have a 254
mm round discharge and can be discharged from the front
or rear.
DOWNDRAFTS
Electrical Supply
Service
Receptacle
210
mm*
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
This appliance is equipped with a cord having a grounding
wire with a grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded.
Consult a qualified HVAC professional for specific installation and ducting applications.
Improper grounding can result in a risk of electric
shock. Consult a qualified electrician if the grounding
instructions are not completely understood, or if
doubt exists as to whether the appliance is properly
grounded.
The downdraft will operate most efficiently with the fewest
number of elbows and transitions and when ductwork does
not exceed 12 m.
Do not use an extension cord. If the power supply cord
is too short, have a qualified electrician install an outlet
near the appliance.
Wolf downdrafts must be vented outside.
540
mm
540 mm
594 mm
GROUNDING INSTRUCTIONS
WARNING
DUCTWORK
TOP VIEW
220-240 V AC, 50 Hz
220 V AC, 60 Hz
10 amp dedicated circuit
grounding-type (earthed)
E
SIDE VIEW
FRONT VIEW
*152 mm back from countertop cut-out when internal blower is rear mounted.
NOTE: Internal blower 152 mm round, side, rear or bottom discharge. Remote blower 254 mm round, rear discharge.
Centerline indicates center of downdraft cut-out.
CUT-OUT WIDTH
MODEL
ICBDD30
ICBDD36
ICBDD45
W
699 mm
851 mm
1003 mm
wolfappliance.com
|
3
SPECIFICATIONS
INSTALLATION
Downdraft
Installation
INSTALLATION WITH SEALED BURNER RANGETOP
W
DOWNDRAFT
CUT-OUT WIDTH
68 mm
E
210 mm*
DOWNDRAFT
TRANSITION
1Install
or internal blowers, remove the existing 254 mm round
F
transition. Refer to the illustration below.
2Install
For remote blowers being discharged from the front, leave
the 254 mm round transition in place.
the top mounting brackets using the #4 sheet
metal screws provided. Refer to the illustration below.
the lower mounting brackets using the #8 x 32
sheet metal screws provided, but do not tighten. The
brackets will need to be adjusted once the downdraft is
placed in the opening. Refer to the illustration below.
RANGETOP OPENING
For remote blowers being discharged from the rear, remove
the 254 mm round transition from the front and solid cover
from the rear of the downdraft, then reinstall the 254 mm
transition on the rear and solid cover on the front.
TOP VIEW
483 mm
PLATFORM DEPTH
210
mm*
540
mm
540 mm
594 mm
E
Top mounting bracket.
SIDE VIEW
FRONT VIEW
*152 mm back from countertop cut-out when internal blower is rear mounted.
NOTE: Internal blower 152 mm round, side, rear or bottom discharge. Remote blower 254 mm round, rear discharge.
Centerline indicates center of downdraft cut-out.
CUT-OUT WIDTH
MODEL
ICBDD30
4
|
English
W
699 mm
Bottom leveling bracket.
Remove transition.
INSTALLATION
Installation
INTERNAL BLOWER
o mount the internal blower on the front or rear of the
T
downdraft:
1Rotate
the blower box so the 152 mm round discharge
is properly located, then disconnect the cable from the
downdraft receptacle and connect it to the blower receptacle. Refer to the illustrations below.
2Once
the blower connection is made and the discharge
properly located, secure the blower to the downdraft
using the four screws provided.
To mount the internal blower on the front of the downdraft
but discharge from the rear:
1Remove
the blower from the blower box.
2Mount
the blower motor to the downdraft using the two
screws provided.
3Remove
the blower plug from the downdraft receptacle
and insert it into the blower receptacle. Refer to the illustration below.
REMOTE BLOWER
COUNTERTOP MOUNTING
1Insert
Place the downdraft in the opening, then secure the bottom
brackets to the cabinet base using the wood screws provided. Once the brackets are secure, tighten the existing
lower bracket screws. Refer to the illustration below.
the electrical supply from the remote blower
through the opening on the downdraft and secure using
an approved cord strain relief.
2Connect
hot to brown, neutral to blue and ground to
green. Refer to the illustration below.
4Once
the plug is installed and the blower secure, install
the blower box to the downdraft using the four screws
provided.
HOT
5Remove
DISCHARGE
DOWNDRAFT
RECEPTACLE
BLOWER
RECEPTACLE
the 152 mm collar from the blower box and
solid cover from the rear of the downdraft, then reinstall
the 152 mm collar on the rear and solid cover on the
blower box. Refer to the illustration below.
Left, right or bottom discharge.
COVER
Once the top is secure, install the undercounter brackets
using the screws provided then install the side covers. Refer
to the illustration below.
GROUND
POWER CORD
RECEPTACLE
WIRING
COVER
DOWNDRAFT
RECEPTACLE
NEUTRAL
Secure the top mounting brackets to the countertop using
the wood screws provided. For solid surface countertops,
silicone may be used but is not provided.
Wiring location.
BLUE
MOUNTING
SCREW
COVER
BROWN
Remote blower wiring.
Blower connection.
Countertop mounting.
Cover installation.
COLLAR
BLOWER
RECEPTACLE
Blower mounting.
Install cover.
wolfappliance.com
|
5
INSTALLATION
Installation
Troubleshooting
CONTROL MODULE
TOP COVER
1
Insert the downdraft plug into a grounded (earthed) receptacle, then check operation. Once operation is verified, raise
the chimney and install the top trim using the three nuts
provided. Verify the top trim is properly aligned with the side
covers. Refer to the illustration below.
se the template provided on page 7 to mark holes for
U
mounting screws. Drill one 40 mm in the center and two
10 mm holes for the mounting screws.
CAUTION
Verify the scale of the template if not using the installation guide shipped with the downdraft.
2Check
countertop thickness to make sure threaded
studs are long enough to allow thumbnuts to fully
engage. Thicker countertops may require the countertop
be countersunk from below.
3Place
the control module on the countertop then secure
using the two nuts provided. Once secure, install the
ground wire and nut.
FILTERS
IMPORTANT NOTE: If the downdraft ventilation system does
not operate properly, follow these troubleshooting steps:
•Verify electrical power is supplied to the downdraft.
•Verify proper electrical connections.
•If the downdraft does not operate properly, contact Wolf
factory certified service. Do not attempt to repair the
downdraft. Wolf is not responsible for service required to
correct a faulty installation.
Remove stickers and shipping brackets and install filters.
Refer to the illustration below.
TOP COVER
4Use
HIGH
OFF
CONTROL MODULE
RJ45
CONNECTOR
NUT
RJ45
CONNECTOR
Downdraft connection.
6
|
English
GROUND
COUNTERTOP
Control module connection.
Top cover installation.
Filter installation.
ON
E2
ZON
HIGH
GE
BRID
ON
OFF
2
CL
EA
R
ON
SIM
HIGH
SIM
WARNING
GROUND
ZONE
OF
F
ON
HIGH
O
OFF
SIM
OFF
MELT
Do not connect to telecommunication network.
HIGH
ON
3
OFF
SIM
ZO
NE
provided cable or cable designated by local codes.
Connect one end of the control cable to back side of
control module and other to electrical connection on
front of downdraft assembly. Ensure all connections are
tight.
CONTROL MODULE TEMPLATE
21 mm
21 mm
65 mm
65 mm
CL
CL
65 mm
65 mm
21 mm
21 mm
CL
0
CL
0
25 mm
SCALE
25 mm
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc. Sub-Zero, Sub-Zero &
Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service marks
of Sub-Zero, Inc. (collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
SCALE
wolfappliance.com
|
7
WOLF APPLIANCE, INC.
PO BOX 44848
MADISON, WI 53744 USA
WWW.WOLFAPPLIANCE.COM
824657 REV-A
10 / 2013