Ordering Information
Specifications
All specifications apply when the unit is
calibrated at ambient temperature after a five
minute warm up. Typical values are given for
reference, and are not guaranteed.
Cable and Antenna Analyzer
Frequency Range: 25 MHz to 4.0 GHz
Frequency Accuracy: ≤ ±75 ppm @ +25˚C
Frequency Resolution: 100 kHz
Output Power: < 0 dBm (–10 dBm nominal)
Immunity to Interfering Signals:
on-channel
+17 dBm
on-frequency
–5 dBm
Measurement speed: ≤3.5 msec / data point (CW ON)
Number of data points: 130, 259, 517
Return Loss: Range: 0.00 to 60.00 dB
Resolution: 0.01 dB
VSWR: Range: 1.00 to 65.00
Resolution: 0.01
Cable Loss: Range: 0.00 to 30.00 dB
Resolution: 0.01 dB
Measurement Accuracy: >42 dB corrected directivity
after calibration
Distance-To-Fault
Vertical Range: Return Loss: 0.00 to 60.00 dB
VSWR: 1.00 to 65.00
Horizontal Range: Range: 0 to (# of data pts –1) x
Resolution to a maximum of 1197 m (3929 ft),
# of data pts = 130, 259, 517
Horizontal Resolution (Rectangular windowing):
Resolution (meter) = (1.5 x 10^8) x (Vp)/DF
Where Vp is the cable's relative propagation
velocity and where DF is the stop frequency minus
the start frequency (in Hz)
Spectrum Analyzer (S332D Models)
Frequency:
Frequency Range: 100 kHz to 3.0 GHz
Measurement Range: +20 dBm to –135 dBm
Frequency Reference (Internal Timebase):
Aging: ±1 ppm/yr
Accuracy: ±2 ppm
Frequency Span: 10 Hz to 2.99 GHz in 1, 2, 5
step selections in auto mode, plus zero span
Sweep Time: ≤1.1 sec full span;
≤ 50 µsec to 20 sec selectable in zero span
Resolution Bandwidth (–3 dB):
100 Hz to 1 MHz in 1-3 sequence ± 5% Accuracy
Video Bandwidth (–3 dB):
3 Hz to 1 MHz in 1-3 sequence ± 5% Accuracy
SSB Phase Noise (1 GHz) @ 30 kHz Offset:
≤–75 dBc/Hz
Spurious Responses: ≤–45 dBc
Spurious Residual Responses: ≤–90dBm, >10 MHz
≤–80 dBm, ≤10 MHz (10 kHz RBW, pre-amp on)
Amplitude:
Total Level Accuracy:
±1 dB typical (±1.5 dBm max), >2 GHz to 3 GHz
±0.5 dB typical (±1 dB max), ≥10 MHz to 2 GHz
±2 dB, ≥ 500 kHz to <10 MHz
±3 dB typical, <500 kHz
for input signal levels ≥ –60 dBm,
excludes input VSWR mismatch
Measurement Range: +20 dBm to –135 dBm
Input Attenuator Range: 0 to 51 dB,
selected manually or automatically coupled to
the reference level. Resolution in 1 dB steps.
Displayed Average Noise Level:
≤–135 dBm typical, ≥10 MHz (preamp on)
≤–115 dBm typical, <10 MHz (preamp on)
for input terminated , 0 dB attenuation,
RMS detection, 100 Hz RBW
Dynamic Range: >65 dB
Display Range: 1 to 15 dB/division, in 1 dB
steps, 10 divisions displayed
Scale Units: dBm, dBV, dBmV, dBuV, V, W
RF Input VSWR: 1.5:1 typical, (≥20 dB atten.,
(10 MHz to 2.4 GHz)
Power Meter (Option 29)
Frequency Range: 3 MHz to 3.0 GHz
Measurement Range: –80 dBm to +20 dBm
Display Range: –80 dBm to +80 dBm
Offset Range: 0 to +60 dB
Accuracy: ±1 dB typical (±1.5 dBm max), >2 GHz to 3 GHz
±0.5 dB typical (±1 dB max), ≥10 MHz to 2 GHz
±2 dB, 3 MHz to <10 MHz
VSWR: 1.5:1 typical (Pin> -30 dBm, 10 MHz to 2.4 GHz)
Maximum Power: +20 dBm (0.1W) without external
attenuator
T1 Analyzer (Option 50 on
S331D Models only)
Line Coding: AMI, B8ZS
Framing Modes: D4 (Superframe), ESF
(Extended Superframe)
Connection Configurations:
Terminate (100Ω)
Bridge (≥1000Ω)
Monitor (Connect via 20 dB pad in DSX)
Receiver Sensitivity: 0 to –36 dBdsx
Transmit Level: 0 dB, –7.5 dB, and -15 dB
Clock Sources: External
Internal: 1.544 MHz ± 30 ppm
Pulse Shapes: Conform to ANSI T1.403
Pattern Generation and Detection: PRBS: 2-9, 2-11,
2-15, 2-20, 2-23 Inverted and non-inverted,
QRSS, 1-in-8 (1-in-7), 2-in-8, 3-in-24, All ones,
All zeros, T1-Daly, User defined (≤ 32 bits)
Circuit Status Reports: Carrier present, Frame ID
and Sync., Pattern ID and Sync.
Alarm Detection: AIS (Blue Alarm), RAI
(Yellow Alarm)
Error Detection: Frame Bits, Bit, BER, BPV, CRC,
Error Sec
Error Insertion: Bit, BPV, Framing Bits, RAI, AIS
Loopback Modes: Self loop, CSU, NIU, User
defined, In-band or Data Link
Level Measurements: Vp-p (± 5%)
Data Log: Continuous, up to 48 hrs
E1 Analyzer (Option 50 on
S331D Models only)
Line Coding: AMI, HDB3
Framing Modes: PCM30, PCM30CRC, PCM31,
PCM31CRC
Connection Configurations:
Terminate (75, 120Ω)
Bridge (≥1000Ω)
Monitor (Connect via 20 dB pad in DSX)
Receiver Sensitivity: 0 to –43 dB
Clock Sources: External
Internal 2.048 MHz ±30 ppm
Pulse Shapes: Conform to ITU G.703
Pattern Generation and Detection:
PRBS: 2-9, 2-11, 2-15, 2-20, 2-23 Inverted and
non-inverted, QRSS, 1-in-8 (1-in-7), 2-in-8, 3-in-24,
All ones, All zeros, T1-Daly, User defined (≤32 bits)
Circuit Status Reports: Carrier present, Frame ID
and Sync., Pattern ID and Sync.
Alarm Detection: AIS, RAI, MMF
Error Detection: Frame Bits, Bit, BER, BPV, CRC, E-Bits,
Error Sec
Error Insertion: Bit, BPV, Framing Bits, RAI, AIS
Loopback Modes: Self loopback
Level Measurements: Vp-p (±5%)
Data Log: Continuous, up to 48 hrs
General
Language Support: Chinese, English, French, German,
Japanese, Spanish,
Internal Trace Memory: 200 traces
Setup Configuration: S332D - 20, S331D - 25
Display: VGA monochrome or VGA color LCD (Option 3)
with adjustable backlight
Inputs and Outputs Ports:
RF Out: Type N, female, 50Ω
Maximum Input without Damage: +23 dBm, ± 50 VDC
RF In: Type N, female, 50Ω
Maximum Input without Damage: +43 dBm (Peak), ± 50 VDC
Ext. Trig In: BNC, female (5 V TTL) (S332D Models only)
Ext. Freq Ref In (2 to 20 MHz): Shared BNC, female,
50Ω, (–15 dBm to +10 dBm) (S332D Models only)
T1/E1 (Receive & Transmit): Bantam Jack
(S331D Models with Option 50 only)
Serial Interface: RS-232 9 pin D-sub, three wire serial
Electromagnetic Compatibility: Meets European
Community requirements for CE marking
Safety: Conforms to EN 61010-1 for Class 1
portable equipment
Temperature:
Operating: –10°C to 55°C, humidity 85% or less
Non-operating: –51°C to +71°C (recommended
battery to store separately between 0°C to +40°C
for any prolonged non-operating storage period)
Environmental: MIL-PRF-28800F Class 2
Power Supply:
External DC Input: +12.5 to +15 volt dc, 1350 mA max
Internal: NiMH battery: 10.8 volts, 1800 mAH
Dimensions:
Size (w x h x d): 25.4 cm x 17.8 cm x 6.1 cm
(10.0 in x 7.0 in x 2.4 in)
Weight: <2.28 kg (<5 lbs) includes battery
Basic Models
S331D Cable and Antenna Analyzer (25 MHz to 4.0 GHz)
with built-in DTF
S332D Cable and Antenna Analyzer (25 MHz to 4.0 GHz),
with built-in DTF, Spectrum Analyzer (100 kHz to 3.0 GHz)
510-90
510-91
510-92
510-93
510-96
510-97
Adapter, 7/16 DIN(f)-N(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(f)-N(f), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-N(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-N(f), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-7/16 DIN(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(f)-7/16 DIN(f), DC to 7.5 GHz, 50Ω
Standard Accessories Include
User's Guide
Soft Carrying Case
AC-DC Adapter with Power Cord
Automotive Cigarette Lighter/12 Volt DC Adapter
One Year Warranty
Handheld Software Tools CDROM containing Fault Location (DTF)
and Smith Chart
Serial Interface Cable
Rechargeable Battery, NiMH
2000-1030
2000-1031
2000-1032
2000-1200
2000-1035
Portable Antenna, SMA (m), 1.71 to 1.88 GHz, 50Ω
Portable Antenna, SMA (m), 1.85 to 1.99 GHz, 50Ω
Portable Antenna, SMA (m), 2.4 to 2.5 GHz, 50Ω
Portable Antenna, SMA (m), 806-869 MHz, 50Ω
Portable Antenna, SMA (m), 896-941 MHz, 50Ω
1030-86
1030-87
1030-88
1030-89
Band Pass Filter, 806-869 MHz, 1.7 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 902-960 MHz, 1.7 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 1.85-1.99 GHz, 1.8 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 2.4-2.5 GHz, 1.4 dB loss, N(m) to SMA(f), 50Ω
Options
Option 3 Color LCD Display
Option 29 Power Meter (does not require external detector)
Option 50 T1/E1 Analyzer (S331D only)
806-16
806-116
806-117
Bantam Plug to Bantam Plug
Bantam Plug to BNC
Bantam "Y" Plug to RJ48
551-1691
USB to RS232 adapter cable
48258
760-229
633-27
2000-1029
40-163
806-62
800-441
2300-347
Soft Carrying Case
Transit Case
Rechargeable Battery, NiMH
Battery Charger, NiMH, w/ Universal Power Supply
AC/DC Adapter
Automotive Cigarette Lighter/12 Volts DC Adapter
Serial Interface Cable
Software Tools
10580-00079
10580-00100
10580-00101
10580-00102
Site Master S331D/S332D User's Guide
Site Master S331D/S332D Programming Manual
Site Master S331D Maintenance Manual
Site Master S332D Maintenance Manual
Optional Accessories
1N50C
Limiter, N(m) to N(f), 50Ω, 10 MHz to 18 GHz
42N50-20
Attenuator, 20 dB, 5 watt, DC to 18 GHz, N(m)-N(f)
42N50A-30
Attenuator, 30 dB, 50 watt, DC to 18 GHz, N(m)-N(f)
InstaCal™ Calibration Module, 2 MHz to 4.0 GHz, N(m), 50Ω
Open/Short, DC to 18 GHz, N(m), 50Ω
Open/Short, DC to 18 GHz, N(f), 50Ω
Precision Load, DC to 4 GHz, 42 dB, N(m), 50Ω
Precision Load, DC to 4 GHz, 42 dB, N(f), 50Ω
Precision Open/Short/Load, DC to 4 GHz, 42 dB, 50Ω, N(m)
Precision Open/Short/Load, DC to 4 GHz, 42 dB, 50Ω, N(f)
Precision Open/Short/Load, DC to 4 GHz, 7/16 DIN(m), 50Ω
Precision Open/Short/Load, DC to 4 GHz, 7/16 DIN(f), 50Ω
ICN50
22N50
22NF50
SM/PL
SM/PLNF
OSLN50LF
OSLNF50LF
2000-767
2000-768
15NN50-1.5C
15NN50-3.0C
15NN50-5.0C
15NNF50-1.5C
15NNF50-3.0C
15NNF50-5.0C
15ND50-1.5C
Test Port Cable Armored, 1.5 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 3.0 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 5.0 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 1.5 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 3.0 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 5.0 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 1.5 meters, N(m)-7/16 DIN(m),
6 GHz, 50Ω
15NDF50-1.5C Test Port Cable Armored, 1.5 meters, N(m)-7/16 DIN(f),
6 GHz, 50Ω
Printers
2000-1214
34NN50A
34NFNF50
Precision Adapter, N(m)-N(m), DC to 18 GHz, 50Ω
Precision Adapter, N(f)-N(f), DC to 18 GHz, 50Ω
1091-26
1091-27
1091-80
1091-81
1091-172
Adapter, N(m)-SMA(m), DC to 18 GHz, 50Ω
Adapter, N(m)-SMA(f), DC to 18 GHz, 50Ω
Adapter, N(f)-SMA(m), DC to 18 GHz, 50Ω
Adapter, N(f)-SMA(f), DC to 18 GHz, 50Ω
Adapter, N(m)-BNC(f), DC to 1.3 GHz, 50Ω
2000-753
1091-310
2000-1216
2000-663
2000-664
2000-667
2000-1217
2000-1218
SALES CENTERS:
United States (800) ANRITSU
Canada (800) ANRITSU
South America 55 (21) 2527-6922
Europe 44 (0) 1582-433433
Japan 81 (46) 223-1111
Asia-Pacific (65) 6282-2400
Site Master
™
S331D/S332D
Cable and Antenna Analyzer
25 MHz to 4000 MHz
HP DeskJet Printer, Model 450: Includes printer cable, 2000-1216
black print cartridge and U.S. power cord. Also includes 2000-753
serial-to-parallel Centronics converter cable and 1091-310
Centronics-to DB25 adapter. Rechargeable battery is optional and
is not included.
Null Modem Serial-to-Parallel Centronics Converter Cable
Adapter 36-pin Centronics female-to-DB25 female
Black Print Cartridge
Power Cable (Europe) for DeskJet Printer
Power Cable (Australia) for DeskJet Printer
Power Cable (S. Africa) for DeskJet Printer
Rechargeable Battery for DeskJet Printer, Model 450
Power Cable (U.K.) for DeskJet Printer
Microwave Measurements Division
490 Jarvis Drive, Morgan Hill, CA 95037-2809
http://www.us.anritsu.com
SiteMaster
S331D Site Master
SiteMaster
MS2712
SiteMaster
MS2711D Spectrum Master
MS2712
SpectrumMaster
SpectrumMaster
MT8212A Cell Master
MS2712
CellMaster
©Anritsu October 2003. All trademarks are registered trademarks of
their respective companies. Data is subject to change without notice.
Discover What’s Possible®
CellMaster
PN: 11410-00321, Rev. A
The World’s Leading Cable and Antenna System Analyzer
Site Master is the preferred cable and antenna analyzer of wireless providers, contractors and installers.
RS-232 Interface
Transfer stored data to and
from a personal computer (PC)
or download to a printer via a
serial cable for further analysis.
Use PC to automatically control
and collect data in the field.
Snap-in Field
replaceable battery
location
External DC
Power Port
Spectrum Analyzer
& Power Meter Port
Ext Trig & Ext Ref In
Cable & Antenna
Analyzer Port
T1/E1
Receive & Transmit Port
(S331D Models with Option 50)
Save & Recall Setup
Setups for fast
repeatable testing:
S332D Models - 20
S331D Models - 25
Rugged & Reliable
Chassis Design
Ruggedized, lightweight,
compact, high-impact housing
is designed to withstand
repeated drops and rough
handling. Weather resistant
seals and rubber membrane
keypad protect unit from dirt
and moisture.
Markers
6 markers for more
comprehensive
measurements.
Limits
Create simple pass/fail
measurements with a single
limit line, upper and/or lower
mask limit lines.
Multilingual User Interface
Multi-language user interface
features on-screen menus and
messages in 6 different
languages: Chinese, English,
French, German, Japanese,
Spanish.
Large High
Resolution Display
Standard VGA (640x480) or
optional color monitor STN
(640x480) display featuring
contrast and variable backlighting capability. Easy viewing
under a variety of conditions.
Function Keys
Four dedicated function keys simplify
measurement tasks.
Soft Keys
Intuitive soft key menu
and user interface.
Save & Recall Display
Up to 200 memory
locations. Alphanumeric
data labeling and
automatic time/date
stamp simplifies data
management.
Cable and Antenna Analyzer
Spectrum Analyzer (S332D Models)
The cable and antenna analyzer tool provides for return loss/SWR, cable loss, and distance-to-fault measurements.
This enables quick evaluations of the health and status of transmission lines and antenna systems, and speeds the
benchmarking of new cell site installations at the time of commissioning.
The spectrum analyzer enables field technicians to analyze and identify over-the-air interference and transmitter
characteristics easily, without having to lug a separate instrument.
Test / Capability
Benefits
Test / Capability
Benefits
25 MHz to 4000 MHz
Covers all cell site frequency ranges without
additional plug-ins or instruments
100 kHz to 3000 MHz
Covers all mobile system frequencies without
requiring additional plug-ins or instruments
Built-in worldwide signal standards
Common language for cell technicians that eliminates
the need to remember and manually input start and
stop frequencies
Built-in worldwide signal standards
and frequency channels
Common language to cell technicians and eliminates
the need to perform channel-to-frequency translation
Built-in calibration intelligence
Ensures accurate and proper calibration
≤ –135 dBm amplitude sensitivity
Ability to detect low level signals
FlexCal™
Allows troubleshooting cable and antenna systems
without multiple calibrations and calibration setups
Quicker, convenient measurements
Superior immunity to interference
Accurate and repeatable measurements in
RF-noisy environments
One-button measurements:
Field Strength, Occupied Bandwidth
Channel Power, Adjacent Channel
Power Ratio, Interference Analysis and
Carrier-to-Interference Ratio
130, 259, and 517 data points
Optimizes distance measurement
resolution and fault locations
Interference Analysis measurement
Analyzes a received signal and displays signal standard
and bandwidth to understand interference problems
< 500 msec per sweep
Enables easier identification of
intermittent, real-time problems
Carrier-to-Interference Ratio (C/I)
measurement
Ensures received signal quality in the
presence of interference
Built-in average cable loss
value computation
No more guess work or need to calculate a measured
cable loss value
Powerful PC based Data Management and Analysis Software
Power Meter (Option 29)
Cost Savings and Quality Improvement
Wireless market competition requires operators to reduce per site maintenance expense.
Site Master’s Frequency Domain Reflectometry (FDR) techniques break away from the
traditional fix-after-failure maintenance process by finding small, hard to identify
problems before major failures occur.
Sixty to eighty percent of a typical cell site’s problems are caused by problematic cables,
connectors and antennas. When cables/antennas are contaminated with moisture or are
damaged/mis-positioned during storms, Site Master identifies the problem quickly.
Antenna degradation reduces the cell coverage pattern and can cause dropped calls. Site
Master can pinpoint the antenna problem from ground level in a few seconds so climbing
to the antenna tower becomes unnecessary.
A poorly installed weather seal will corrode connectors and, if undetected, will eventually
damage an expensive coaxial cable. Site Master has the sensitivity to identify the connector
problem before the cable is damaged. Distance-To-Fault provides the clearest indication
of troubled areas.
Site Master
revolutionizes
Cable and
Antenna
Sweeping in
the Wireless
Industry.
The power meter tool performs accurate power measurements, reducing coverage holes and interference.
Test / Capability
Benefits
Requires no additional power sensors
No additional parts to carry to the field
A comprehensive data management and analysis software suite comes with every Site Master unit, providing users
with a simple and easy method of managing, archiving, and analyzing system performance, trends, and the general
health of monitored base stations. The Handheld Software Tools also provide a professional report generator, for
those times when recorded data must be communicated.
• The Handheld Software Tools are Windows 95/98/NT4/2000/ME/XP compatible,
and supports long alpha-numeric file names for descriptive data labeling
• Stores an unlimited number of data traces for comparison of historical performance
measurements, easing the task of trend analysis
• Transfer data traces between the Site Master and the PC with a single menu selection
T1 and E1 Analyzer (Option 50 on S331D Models only)
The Site Master performs full T1/E1 functional tests, simplifying the task of determining if the source of
problems is on the wireline or the wireless side.
Test / Capability
Benefits
Full function T1 and E1 tests
No need to purchase or carry separate
wireline testers
Histogram display
Provide continuous monitoring or overnight
monitoring of wireline health
• Has the ability to convert Return Loss measurements to Distance-To-Fault measurements
• Handheld Software Tools has DTF and Smith Chart analysis capabilities
Color LCD Display (Option 3)
640x480 color STN display for crisp display/trace representation in indoor lighting conditions.
Site Master is the preferred cable and antenna analyzer of wireless providers, contractors and installers.
RS-232 Interface
Transfer stored data to and
from a personal computer (PC)
or download to a printer via a
serial cable for further analysis.
Use PC to automatically control
and collect data in the field.
Snap-in Field
replaceable battery
location
External DC
Power Port
Spectrum Analyzer
& Power Meter Port
Ext Trig & Ext Ref In
Cable & Antenna
Analyzer Port
T1/E1
Receive & Transmit Port
(S331D Models with Option 50)
Save & Recall Setup
Setups for fast
repeatable testing:
S332D Models - 20
S331D Models - 25
Rugged & Reliable
Chassis Design
Ruggedized, lightweight,
compact, high-impact housing
is designed to withstand
repeated drops and rough
handling. Weather resistant
seals and rubber membrane
keypad protect unit from dirt
and moisture.
Markers
6 markers for more
comprehensive
measurements.
Limits
Create simple pass/fail
measurements with a single
limit line, upper and/or lower
mask limit lines.
Multilingual User Interface
Multi-language user interface
features on-screen menus and
messages in 6 different
languages: Chinese, English,
French, German, Japanese,
Spanish.
Large High
Resolution Display
Standard VGA (640x480) or
optional color monitor STN
(640x480) display featuring
contrast and variable backlighting capability. Easy viewing
under a variety of conditions.
Function Keys
Four dedicated function keys simplify
measurement tasks.
Soft Keys
Intuitive soft key menu
and user interface.
Save & Recall Display
Up to 200 memory
locations. Alphanumeric
data labeling and
automatic time/date
stamp simplifies data
management.
Cable and Antenna Analyzer
Spectrum Analyzer (S332D Models)
The cable and antenna analyzer tool provides for return loss/SWR, cable loss, and distance-to-fault measurements.
This enables quick evaluations of the health and status of transmission lines and antenna systems, and speeds the
benchmarking of new cell site installations at the time of commissioning.
The spectrum analyzer enables field technicians to analyze and identify over-the-air interference and transmitter
characteristics easily, without having to lug a separate instrument.
Test / Capability
Benefits
Test / Capability
Benefits
25 MHz to 4000 MHz
Covers all cell site frequency ranges without
additional plug-ins or instruments
100 kHz to 3000 MHz
Covers all mobile system frequencies without
requiring additional plug-ins or instruments
Built-in worldwide signal standards
Common language for cell technicians that eliminates
the need to remember and manually input start and
stop frequencies
Built-in worldwide signal standards
and frequency channels
Common language to cell technicians and eliminates
the need to perform channel-to-frequency translation
Built-in calibration intelligence
Ensures accurate and proper calibration
≤ –135 dBm amplitude sensitivity
Ability to detect low level signals
FlexCal™
Allows troubleshooting cable and antenna systems
without multiple calibrations and calibration setups
Quicker, convenient measurements
Superior immunity to interference
Accurate and repeatable measurements in
RF-noisy environments
One-button measurements:
Field Strength, Occupied Bandwidth
Channel Power, Adjacent Channel
Power Ratio, Interference Analysis and
Carrier-to-Interference Ratio
130, 259, and 517 data points
Optimizes distance measurement
resolution and fault locations
Interference Analysis measurement
Analyzes a received signal and displays signal standard
and bandwidth to understand interference problems
< 500 msec per sweep
Enables easier identification of
intermittent, real-time problems
Carrier-to-Interference Ratio (C/I)
measurement
Ensures received signal quality in the
presence of interference
Built-in average cable loss
value computation
No more guess work or need to calculate a measured
cable loss value
Powerful PC based Data Management and Analysis Software
Power Meter (Option 29)
Cost Savings and Quality Improvement
Wireless market competition requires operators to reduce per site maintenance expense.
Site Master’s Frequency Domain Reflectometry (FDR) techniques break away from the
traditional fix-after-failure maintenance process by finding small, hard to identify
problems before major failures occur.
Sixty to eighty percent of a typical cell site’s problems are caused by problematic cables,
connectors and antennas. When cables/antennas are contaminated with moisture or are
damaged/mis-positioned during storms, Site Master identifies the problem quickly.
Antenna degradation reduces the cell coverage pattern and can cause dropped calls. Site
Master can pinpoint the antenna problem from ground level in a few seconds so climbing
to the antenna tower becomes unnecessary.
A poorly installed weather seal will corrode connectors and, if undetected, will eventually
damage an expensive coaxial cable. Site Master has the sensitivity to identify the connector
problem before the cable is damaged. Distance-To-Fault provides the clearest indication
of troubled areas.
Site Master
revolutionizes
Cable and
Antenna
Sweeping in
the Wireless
Industry.
The power meter tool performs accurate power measurements, reducing coverage holes and interference.
Test / Capability
Benefits
Requires no additional power sensors
No additional parts to carry to the field
A comprehensive data management and analysis software suite comes with every Site Master unit, providing users
with a simple and easy method of managing, archiving, and analyzing system performance, trends, and the general
health of monitored base stations. The Handheld Software Tools also provide a professional report generator, for
those times when recorded data must be communicated.
• The Handheld Software Tools are Windows 95/98/NT4/2000/ME/XP compatible,
and supports long alpha-numeric file names for descriptive data labeling
• Stores an unlimited number of data traces for comparison of historical performance
measurements, easing the task of trend analysis
• Transfer data traces between the Site Master and the PC with a single menu selection
T1 and E1 Analyzer (Option 50 on S331D Models only)
The Site Master performs full T1/E1 functional tests, simplifying the task of determining if the source of
problems is on the wireline or the wireless side.
Test / Capability
Benefits
Full function T1 and E1 tests
No need to purchase or carry separate
wireline testers
Histogram display
Provide continuous monitoring or overnight
monitoring of wireline health
• Has the ability to convert Return Loss measurements to Distance-To-Fault measurements
• Handheld Software Tools has DTF and Smith Chart analysis capabilities
Color LCD Display (Option 3)
640x480 color STN display for crisp display/trace representation in indoor lighting conditions.
Site Master is the preferred cable and antenna analyzer of wireless providers, contractors and installers.
RS-232 Interface
Transfer stored data to and
from a personal computer (PC)
or download to a printer via a
serial cable for further analysis.
Use PC to automatically control
and collect data in the field.
Snap-in Field
replaceable battery
location
External DC
Power Port
Spectrum Analyzer
& Power Meter Port
Ext Trig & Ext Ref In
Cable & Antenna
Analyzer Port
T1/E1
Receive & Transmit Port
(S331D Models with Option 50)
Save & Recall Setup
Setups for fast
repeatable testing:
S332D Models - 20
S331D Models - 25
Rugged & Reliable
Chassis Design
Ruggedized, lightweight,
compact, high-impact housing
is designed to withstand
repeated drops and rough
handling. Weather resistant
seals and rubber membrane
keypad protect unit from dirt
and moisture.
Markers
6 markers for more
comprehensive
measurements.
Limits
Create simple pass/fail
measurements with a single
limit line, upper and/or lower
mask limit lines.
Multilingual User Interface
Multi-language user interface
features on-screen menus and
messages in 6 different
languages: Chinese, English,
French, German, Japanese,
Spanish.
Large High
Resolution Display
Standard VGA (640x480) or
optional color monitor STN
(640x480) display featuring
contrast and variable backlighting capability. Easy viewing
under a variety of conditions.
Function Keys
Four dedicated function keys simplify
measurement tasks.
Soft Keys
Intuitive soft key menu
and user interface.
Save & Recall Display
Up to 200 memory
locations. Alphanumeric
data labeling and
automatic time/date
stamp simplifies data
management.
Cable and Antenna Analyzer
Spectrum Analyzer (S332D Models)
The cable and antenna analyzer tool provides for return loss/SWR, cable loss, and distance-to-fault measurements.
This enables quick evaluations of the health and status of transmission lines and antenna systems, and speeds the
benchmarking of new cell site installations at the time of commissioning.
The spectrum analyzer enables field technicians to analyze and identify over-the-air interference and transmitter
characteristics easily, without having to lug a separate instrument.
Test / Capability
Benefits
Test / Capability
Benefits
25 MHz to 4000 MHz
Covers all cell site frequency ranges without
additional plug-ins or instruments
100 kHz to 3000 MHz
Covers all mobile system frequencies without
requiring additional plug-ins or instruments
Built-in worldwide signal standards
Common language for cell technicians that eliminates
the need to remember and manually input start and
stop frequencies
Built-in worldwide signal standards
and frequency channels
Common language to cell technicians and eliminates
the need to perform channel-to-frequency translation
Built-in calibration intelligence
Ensures accurate and proper calibration
≤ –135 dBm amplitude sensitivity
Ability to detect low level signals
FlexCal™
Allows troubleshooting cable and antenna systems
without multiple calibrations and calibration setups
Quicker, convenient measurements
Superior immunity to interference
Accurate and repeatable measurements in
RF-noisy environments
One-button measurements:
Field Strength, Occupied Bandwidth
Channel Power, Adjacent Channel
Power Ratio, Interference Analysis and
Carrier-to-Interference Ratio
130, 259, and 517 data points
Optimizes distance measurement
resolution and fault locations
Interference Analysis measurement
Analyzes a received signal and displays signal standard
and bandwidth to understand interference problems
< 500 msec per sweep
Enables easier identification of
intermittent, real-time problems
Carrier-to-Interference Ratio (C/I)
measurement
Ensures received signal quality in the
presence of interference
Built-in average cable loss
value computation
No more guess work or need to calculate a measured
cable loss value
Powerful PC based Data Management and Analysis Software
Power Meter (Option 29)
Cost Savings and Quality Improvement
Wireless market competition requires operators to reduce per site maintenance expense.
Site Master’s Frequency Domain Reflectometry (FDR) techniques break away from the
traditional fix-after-failure maintenance process by finding small, hard to identify
problems before major failures occur.
Sixty to eighty percent of a typical cell site’s problems are caused by problematic cables,
connectors and antennas. When cables/antennas are contaminated with moisture or are
damaged/mis-positioned during storms, Site Master identifies the problem quickly.
Antenna degradation reduces the cell coverage pattern and can cause dropped calls. Site
Master can pinpoint the antenna problem from ground level in a few seconds so climbing
to the antenna tower becomes unnecessary.
A poorly installed weather seal will corrode connectors and, if undetected, will eventually
damage an expensive coaxial cable. Site Master has the sensitivity to identify the connector
problem before the cable is damaged. Distance-To-Fault provides the clearest indication
of troubled areas.
Site Master
revolutionizes
Cable and
Antenna
Sweeping in
the Wireless
Industry.
The power meter tool performs accurate power measurements, reducing coverage holes and interference.
Test / Capability
Benefits
Requires no additional power sensors
No additional parts to carry to the field
A comprehensive data management and analysis software suite comes with every Site Master unit, providing users
with a simple and easy method of managing, archiving, and analyzing system performance, trends, and the general
health of monitored base stations. The Handheld Software Tools also provide a professional report generator, for
those times when recorded data must be communicated.
• The Handheld Software Tools are Windows 95/98/NT4/2000/ME/XP compatible,
and supports long alpha-numeric file names for descriptive data labeling
• Stores an unlimited number of data traces for comparison of historical performance
measurements, easing the task of trend analysis
• Transfer data traces between the Site Master and the PC with a single menu selection
T1 and E1 Analyzer (Option 50 on S331D Models only)
The Site Master performs full T1/E1 functional tests, simplifying the task of determining if the source of
problems is on the wireline or the wireless side.
Test / Capability
Benefits
Full function T1 and E1 tests
No need to purchase or carry separate
wireline testers
Histogram display
Provide continuous monitoring or overnight
monitoring of wireline health
• Has the ability to convert Return Loss measurements to Distance-To-Fault measurements
• Handheld Software Tools has DTF and Smith Chart analysis capabilities
Color LCD Display (Option 3)
640x480 color STN display for crisp display/trace representation in indoor lighting conditions.
Ordering Information
Specifications
All specifications apply when the unit is
calibrated at ambient temperature after a five
minute warm up. Typical values are given for
reference, and are not guaranteed.
Cable and Antenna Analyzer
Frequency Range: 25 MHz to 4.0 GHz
Frequency Accuracy: ≤ ±75 ppm @ +25˚C
Frequency Resolution: 100 kHz
Output Power: < 0 dBm (–10 dBm nominal)
Immunity to Interfering Signals:
on-channel
+17 dBm
on-frequency
–5 dBm
Measurement speed: ≤3.5 msec / data point (CW ON)
Number of data points: 130, 259, 517
Return Loss: Range: 0.00 to 60.00 dB
Resolution: 0.01 dB
VSWR: Range: 1.00 to 65.00
Resolution: 0.01
Cable Loss: Range: 0.00 to 30.00 dB
Resolution: 0.01 dB
Measurement Accuracy: >42 dB corrected directivity
after calibration
Distance-To-Fault
Vertical Range: Return Loss: 0.00 to 60.00 dB
VSWR: 1.00 to 65.00
Horizontal Range: Range: 0 to (# of data pts –1) x
Resolution to a maximum of 1197 m (3929 ft),
# of data pts = 130, 259, 517
Horizontal Resolution (Rectangular windowing):
Resolution (meter) = (1.5 x 10^8) x (Vp)/DF
Where Vp is the cable's relative propagation
velocity and where DF is the stop frequency minus
the start frequency (in Hz)
Spectrum Analyzer (S332D Models)
Frequency:
Frequency Range: 100 kHz to 3.0 GHz
Measurement Range: +20 dBm to –135 dBm
Frequency Reference (Internal Timebase):
Aging: ±1 ppm/yr
Accuracy: ±2 ppm
Frequency Span: 10 Hz to 2.99 GHz in 1, 2, 5
step selections in auto mode, plus zero span
Sweep Time: ≤1.1 sec full span;
≤ 50 µsec to 20 sec selectable in zero span
Resolution Bandwidth (–3 dB):
100 Hz to 1 MHz in 1-3 sequence ± 5% Accuracy
Video Bandwidth (–3 dB):
3 Hz to 1 MHz in 1-3 sequence ± 5% Accuracy
SSB Phase Noise (1 GHz) @ 30 kHz Offset:
≤–75 dBc/Hz
Spurious Responses: ≤–45 dBc
Spurious Residual Responses: ≤–90dBm, >10 MHz
≤–80 dBm, ≤10 MHz (10 kHz RBW, pre-amp on)
Amplitude:
Total Level Accuracy:
±1 dB typical (±1.5 dBm max), >2 GHz to 3 GHz
±0.5 dB typical (±1 dB max), ≥10 MHz to 2 GHz
±2 dB, ≥ 500 kHz to <10 MHz
±3 dB typical, <500 kHz
for input signal levels ≥ –60 dBm,
excludes input VSWR mismatch
Measurement Range: +20 dBm to –135 dBm
Input Attenuator Range: 0 to 51 dB,
selected manually or automatically coupled to
the reference level. Resolution in 1 dB steps.
Displayed Average Noise Level:
≤–135 dBm typical, ≥10 MHz (preamp on)
≤–115 dBm typical, <10 MHz (preamp on)
for input terminated , 0 dB attenuation,
RMS detection, 100 Hz RBW
Dynamic Range: >65 dB
Display Range: 1 to 15 dB/division, in 1 dB
steps, 10 divisions displayed
Scale Units: dBm, dBV, dBmV, dBuV, V, W
RF Input VSWR: 1.5:1 typical, (≥20 dB atten.,
(10 MHz to 2.4 GHz)
Power Meter (Option 29)
Frequency Range: 3 MHz to 3.0 GHz
Measurement Range: –80 dBm to +20 dBm
Display Range: –80 dBm to +80 dBm
Offset Range: 0 to +60 dB
Accuracy: ±1 dB typical (±1.5 dBm max), >2 GHz to 3 GHz
±0.5 dB typical (±1 dB max), ≥10 MHz to 2 GHz
±2 dB, 3 MHz to <10 MHz
VSWR: 1.5:1 typical (Pin> -30 dBm, 10 MHz to 2.4 GHz)
Maximum Power: +20 dBm (0.1W) without external
attenuator
T1 Analyzer (Option 50 on
S331D Models only)
Line Coding: AMI, B8ZS
Framing Modes: D4 (Superframe), ESF
(Extended Superframe)
Connection Configurations:
Terminate (100Ω)
Bridge (≥1000Ω)
Monitor (Connect via 20 dB pad in DSX)
Receiver Sensitivity: 0 to –36 dBdsx
Transmit Level: 0 dB, –7.5 dB, and -15 dB
Clock Sources: External
Internal: 1.544 MHz ± 30 ppm
Pulse Shapes: Conform to ANSI T1.403
Pattern Generation and Detection: PRBS: 2-9, 2-11,
2-15, 2-20, 2-23 Inverted and non-inverted,
QRSS, 1-in-8 (1-in-7), 2-in-8, 3-in-24, All ones,
All zeros, T1-Daly, User defined (≤ 32 bits)
Circuit Status Reports: Carrier present, Frame ID
and Sync., Pattern ID and Sync.
Alarm Detection: AIS (Blue Alarm), RAI
(Yellow Alarm)
Error Detection: Frame Bits, Bit, BER, BPV, CRC,
Error Sec
Error Insertion: Bit, BPV, Framing Bits, RAI, AIS
Loopback Modes: Self loop, CSU, NIU, User
defined, In-band or Data Link
Level Measurements: Vp-p (± 5%)
Data Log: Continuous, up to 48 hrs
E1 Analyzer (Option 50 on
S331D Models only)
Line Coding: AMI, HDB3
Framing Modes: PCM30, PCM30CRC, PCM31,
PCM31CRC
Connection Configurations:
Terminate (75, 120Ω)
Bridge (≥1000Ω)
Monitor (Connect via 20 dB pad in DSX)
Receiver Sensitivity: 0 to –43 dB
Clock Sources: External
Internal 2.048 MHz ±30 ppm
Pulse Shapes: Conform to ITU G.703
Pattern Generation and Detection:
PRBS: 2-9, 2-11, 2-15, 2-20, 2-23 Inverted and
non-inverted, QRSS, 1-in-8 (1-in-7), 2-in-8, 3-in-24,
All ones, All zeros, T1-Daly, User defined (≤32 bits)
Circuit Status Reports: Carrier present, Frame ID
and Sync., Pattern ID and Sync.
Alarm Detection: AIS, RAI, MMF
Error Detection: Frame Bits, Bit, BER, BPV, CRC, E-Bits,
Error Sec
Error Insertion: Bit, BPV, Framing Bits, RAI, AIS
Loopback Modes: Self loopback
Level Measurements: Vp-p (±5%)
Data Log: Continuous, up to 48 hrs
General
Language Support: Chinese, English, French, German,
Japanese, Spanish,
Internal Trace Memory: 200 traces
Setup Configuration: S332D - 20, S331D - 25
Display: VGA monochrome or VGA color LCD (Option 3)
with adjustable backlight
Inputs and Outputs Ports:
RF Out: Type N, female, 50Ω
Maximum Input without Damage: +23 dBm, ± 50 VDC
RF In: Type N, female, 50Ω
Maximum Input without Damage: +43 dBm (Peak), ± 50 VDC
Ext. Trig In: BNC, female (5 V TTL) (S332D Models only)
Ext. Freq Ref In (2 to 20 MHz): Shared BNC, female,
50Ω, (–15 dBm to +10 dBm) (S332D Models only)
T1/E1 (Receive & Transmit): Bantam Jack
(S331D Models with Option 50 only)
Serial Interface: RS-232 9 pin D-sub, three wire serial
Electromagnetic Compatibility: Meets European
Community requirements for CE marking
Safety: Conforms to EN 61010-1 for Class 1
portable equipment
Temperature:
Operating: –10°C to 55°C, humidity 85% or less
Non-operating: –51°C to +71°C (recommended
battery to store separately between 0°C to +40°C
for any prolonged non-operating storage period)
Environmental: MIL-PRF-28800F Class 2
Power Supply:
External DC Input: +12.5 to +15 volt dc, 1350 mA max
Internal: NiMH battery: 10.8 volts, 1800 mAH
Dimensions:
Size (w x h x d): 25.4 cm x 17.8 cm x 6.1 cm
(10.0 in x 7.0 in x 2.4 in)
Weight: <2.28 kg (<5 lbs) includes battery
Basic Models
S331D Cable and Antenna Analyzer (25 MHz to 4.0 GHz)
with built-in DTF
S332D Cable and Antenna Analyzer (25 MHz to 4.0 GHz),
with built-in DTF, Spectrum Analyzer (100 kHz to 3.0 GHz)
510-90
510-91
510-92
510-93
510-96
510-97
Adapter, 7/16 DIN(f)-N(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(f)-N(f), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-N(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-N(f), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-7/16 DIN(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(f)-7/16 DIN(f), DC to 7.5 GHz, 50Ω
Standard Accessories Include
User's Guide
Soft Carrying Case
AC-DC Adapter with Power Cord
Automotive Cigarette Lighter/12 Volt DC Adapter
One Year Warranty
Handheld Software Tools CDROM containing Fault Location (DTF)
and Smith Chart
Serial Interface Cable
Rechargeable Battery, NiMH
2000-1030
2000-1031
2000-1032
2000-1200
2000-1035
Portable Antenna, SMA (m), 1.71 to 1.88 GHz, 50Ω
Portable Antenna, SMA (m), 1.85 to 1.99 GHz, 50Ω
Portable Antenna, SMA (m), 2.4 to 2.5 GHz, 50Ω
Portable Antenna, SMA (m), 806-869 MHz, 50Ω
Portable Antenna, SMA (m), 896-941 MHz, 50Ω
1030-86
1030-87
1030-88
1030-89
Band Pass Filter, 806-869 MHz, 1.7 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 902-960 MHz, 1.7 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 1.85-1.99 GHz, 1.8 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 2.4-2.5 GHz, 1.4 dB loss, N(m) to SMA(f), 50Ω
Options
Option 3 Color LCD Display
Option 29 Power Meter (does not require external detector)
Option 50 T1/E1 Analyzer (S331D only)
806-16
806-116
806-117
Bantam Plug to Bantam Plug
Bantam Plug to BNC
Bantam "Y" Plug to RJ48
551-1691
USB to RS232 adapter cable
48258
760-229
633-27
2000-1029
40-163
806-62
800-441
2300-347
Soft Carrying Case
Transit Case
Rechargeable Battery, NiMH
Battery Charger, NiMH, w/ Universal Power Supply
AC/DC Adapter
Automotive Cigarette Lighter/12 Volts DC Adapter
Serial Interface Cable
Software Tools
10580-00079
10580-00100
10580-00101
10580-00102
Site Master S331D/S332D User's Guide
Site Master S331D/S332D Programming Manual
Site Master S331D Maintenance Manual
Site Master S332D Maintenance Manual
Optional Accessories
1N50C
Limiter, N(m) to N(f), 50Ω, 10 MHz to 18 GHz
42N50-20
Attenuator, 20 dB, 5 watt, DC to 18 GHz, N(m)-N(f)
42N50A-30
Attenuator, 30 dB, 50 watt, DC to 18 GHz, N(m)-N(f)
InstaCal™ Calibration Module, 2 MHz to 4.0 GHz, N(m), 50Ω
Open/Short, DC to 18 GHz, N(m), 50Ω
Open/Short, DC to 18 GHz, N(f), 50Ω
Precision Load, DC to 4 GHz, 42 dB, N(m), 50Ω
Precision Load, DC to 4 GHz, 42 dB, N(f), 50Ω
Precision Open/Short/Load, DC to 4 GHz, 42 dB, 50Ω, N(m)
Precision Open/Short/Load, DC to 4 GHz, 42 dB, 50Ω, N(f)
Precision Open/Short/Load, DC to 4 GHz, 7/16 DIN(m), 50Ω
Precision Open/Short/Load, DC to 4 GHz, 7/16 DIN(f), 50Ω
ICN50
22N50
22NF50
SM/PL
SM/PLNF
OSLN50LF
OSLNF50LF
2000-767
2000-768
15NN50-1.5C
15NN50-3.0C
15NN50-5.0C
15NNF50-1.5C
15NNF50-3.0C
15NNF50-5.0C
15ND50-1.5C
Test Port Cable Armored, 1.5 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 3.0 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 5.0 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 1.5 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 3.0 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 5.0 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 1.5 meters, N(m)-7/16 DIN(m),
6 GHz, 50Ω
15NDF50-1.5C Test Port Cable Armored, 1.5 meters, N(m)-7/16 DIN(f),
6 GHz, 50Ω
Printers
2000-1214
34NN50A
34NFNF50
Precision Adapter, N(m)-N(m), DC to 18 GHz, 50Ω
Precision Adapter, N(f)-N(f), DC to 18 GHz, 50Ω
1091-26
1091-27
1091-80
1091-81
1091-172
Adapter, N(m)-SMA(m), DC to 18 GHz, 50Ω
Adapter, N(m)-SMA(f), DC to 18 GHz, 50Ω
Adapter, N(f)-SMA(m), DC to 18 GHz, 50Ω
Adapter, N(f)-SMA(f), DC to 18 GHz, 50Ω
Adapter, N(m)-BNC(f), DC to 1.3 GHz, 50Ω
2000-753
1091-310
2000-1216
2000-663
2000-664
2000-667
2000-1217
2000-1218
SALES CENTERS:
United States (800) ANRITSU
Canada (800) ANRITSU
South America 55 (21) 2527-6922
Europe 44 (0) 1582-433433
Japan 81 (46) 223-1111
Asia-Pacific (65) 6282-2400
Site Master
™
S331D/S332D
Cable and Antenna Analyzer
25 MHz to 4000 MHz
HP DeskJet Printer, Model 450: Includes printer cable, 2000-1216
black print cartridge and U.S. power cord. Also includes 2000-753
serial-to-parallel Centronics converter cable and 1091-310
Centronics-to DB25 adapter. Rechargeable battery is optional and
is not included.
Null Modem Serial-to-Parallel Centronics Converter Cable
Adapter 36-pin Centronics female-to-DB25 female
Black Print Cartridge
Power Cable (Europe) for DeskJet Printer
Power Cable (Australia) for DeskJet Printer
Power Cable (S. Africa) for DeskJet Printer
Rechargeable Battery for DeskJet Printer, Model 450
Power Cable (U.K.) for DeskJet Printer
Microwave Measurements Division
490 Jarvis Drive, Morgan Hill, CA 95037-2809
http://www.us.anritsu.com
SiteMaster
S331D Site Master
SiteMaster
MS2712
SiteMaster
MS2711D Spectrum Master
MS2712
SpectrumMaster
SpectrumMaster
MT8212A Cell Master
MS2712
CellMaster
©Anritsu October 2003. All trademarks are registered trademarks of
their respective companies. Data is subject to change without notice.
Discover What’s Possible®
CellMaster
PN: 11410-00321, Rev. A
The World’s Leading Cable and Antenna System Analyzer
Ordering Information
Specifications
All specifications apply when the unit is
calibrated at ambient temperature after a five
minute warm up. Typical values are given for
reference, and are not guaranteed.
Cable and Antenna Analyzer
Frequency Range: 25 MHz to 4.0 GHz
Frequency Accuracy: ≤ ±75 ppm @ +25˚C
Frequency Resolution: 100 kHz
Output Power: < 0 dBm (–10 dBm nominal)
Immunity to Interfering Signals:
on-channel
+17 dBm
on-frequency
–5 dBm
Measurement speed: ≤3.5 msec / data point (CW ON)
Number of data points: 130, 259, 517
Return Loss: Range: 0.00 to 60.00 dB
Resolution: 0.01 dB
VSWR: Range: 1.00 to 65.00
Resolution: 0.01
Cable Loss: Range: 0.00 to 30.00 dB
Resolution: 0.01 dB
Measurement Accuracy: >42 dB corrected directivity
after calibration
Distance-To-Fault
Vertical Range: Return Loss: 0.00 to 60.00 dB
VSWR: 1.00 to 65.00
Horizontal Range: Range: 0 to (# of data pts –1) x
Resolution to a maximum of 1197 m (3929 ft),
# of data pts = 130, 259, 517
Horizontal Resolution (Rectangular windowing):
Resolution (meter) = (1.5 x 10^8) x (Vp)/DF
Where Vp is the cable's relative propagation
velocity and where DF is the stop frequency minus
the start frequency (in Hz)
Spectrum Analyzer (S332D Models)
Frequency:
Frequency Range: 100 kHz to 3.0 GHz
Measurement Range: +20 dBm to –135 dBm
Frequency Reference (Internal Timebase):
Aging: ±1 ppm/yr
Accuracy: ±2 ppm
Frequency Span: 10 Hz to 2.99 GHz in 1, 2, 5
step selections in auto mode, plus zero span
Sweep Time: ≤1.1 sec full span;
≤ 50 µsec to 20 sec selectable in zero span
Resolution Bandwidth (–3 dB):
100 Hz to 1 MHz in 1-3 sequence ± 5% Accuracy
Video Bandwidth (–3 dB):
3 Hz to 1 MHz in 1-3 sequence ± 5% Accuracy
SSB Phase Noise (1 GHz) @ 30 kHz Offset:
≤–75 dBc/Hz
Spurious Responses: ≤–45 dBc
Spurious Residual Responses: ≤–90dBm, >10 MHz
≤–80 dBm, ≤10 MHz (10 kHz RBW, pre-amp on)
Amplitude:
Total Level Accuracy:
±1 dB typical (±1.5 dBm max), >2 GHz to 3 GHz
±0.5 dB typical (±1 dB max), ≥10 MHz to 2 GHz
±2 dB, ≥ 500 kHz to <10 MHz
±3 dB typical, <500 kHz
for input signal levels ≥ –60 dBm,
excludes input VSWR mismatch
Measurement Range: +20 dBm to –135 dBm
Input Attenuator Range: 0 to 51 dB,
selected manually or automatically coupled to
the reference level. Resolution in 1 dB steps.
Displayed Average Noise Level:
≤–135 dBm typical, ≥10 MHz (preamp on)
≤–115 dBm typical, <10 MHz (preamp on)
for input terminated , 0 dB attenuation,
RMS detection, 100 Hz RBW
Dynamic Range: >65 dB
Display Range: 1 to 15 dB/division, in 1 dB
steps, 10 divisions displayed
Scale Units: dBm, dBV, dBmV, dBuV, V, W
RF Input VSWR: 1.5:1 typical, (≥20 dB atten.,
(10 MHz to 2.4 GHz)
Power Meter (Option 29)
Frequency Range: 3 MHz to 3.0 GHz
Measurement Range: –80 dBm to +20 dBm
Display Range: –80 dBm to +80 dBm
Offset Range: 0 to +60 dB
Accuracy: ±1 dB typical (±1.5 dBm max), >2 GHz to 3 GHz
±0.5 dB typical (±1 dB max), ≥10 MHz to 2 GHz
±2 dB, 3 MHz to <10 MHz
VSWR: 1.5:1 typical (Pin> -30 dBm, 10 MHz to 2.4 GHz)
Maximum Power: +20 dBm (0.1W) without external
attenuator
T1 Analyzer (Option 50 on
S331D Models only)
Line Coding: AMI, B8ZS
Framing Modes: D4 (Superframe), ESF
(Extended Superframe)
Connection Configurations:
Terminate (100Ω)
Bridge (≥1000Ω)
Monitor (Connect via 20 dB pad in DSX)
Receiver Sensitivity: 0 to –36 dBdsx
Transmit Level: 0 dB, –7.5 dB, and -15 dB
Clock Sources: External
Internal: 1.544 MHz ± 30 ppm
Pulse Shapes: Conform to ANSI T1.403
Pattern Generation and Detection: PRBS: 2-9, 2-11,
2-15, 2-20, 2-23 Inverted and non-inverted,
QRSS, 1-in-8 (1-in-7), 2-in-8, 3-in-24, All ones,
All zeros, T1-Daly, User defined (≤ 32 bits)
Circuit Status Reports: Carrier present, Frame ID
and Sync., Pattern ID and Sync.
Alarm Detection: AIS (Blue Alarm), RAI
(Yellow Alarm)
Error Detection: Frame Bits, Bit, BER, BPV, CRC,
Error Sec
Error Insertion: Bit, BPV, Framing Bits, RAI, AIS
Loopback Modes: Self loop, CSU, NIU, User
defined, In-band or Data Link
Level Measurements: Vp-p (± 5%)
Data Log: Continuous, up to 48 hrs
E1 Analyzer (Option 50 on
S331D Models only)
Line Coding: AMI, HDB3
Framing Modes: PCM30, PCM30CRC, PCM31,
PCM31CRC
Connection Configurations:
Terminate (75, 120Ω)
Bridge (≥1000Ω)
Monitor (Connect via 20 dB pad in DSX)
Receiver Sensitivity: 0 to –43 dB
Clock Sources: External
Internal 2.048 MHz ±30 ppm
Pulse Shapes: Conform to ITU G.703
Pattern Generation and Detection:
PRBS: 2-9, 2-11, 2-15, 2-20, 2-23 Inverted and
non-inverted, QRSS, 1-in-8 (1-in-7), 2-in-8, 3-in-24,
All ones, All zeros, T1-Daly, User defined (≤32 bits)
Circuit Status Reports: Carrier present, Frame ID
and Sync., Pattern ID and Sync.
Alarm Detection: AIS, RAI, MMF
Error Detection: Frame Bits, Bit, BER, BPV, CRC, E-Bits,
Error Sec
Error Insertion: Bit, BPV, Framing Bits, RAI, AIS
Loopback Modes: Self loopback
Level Measurements: Vp-p (±5%)
Data Log: Continuous, up to 48 hrs
General
Language Support: Chinese, English, French, German,
Japanese, Spanish,
Internal Trace Memory: 200 traces
Setup Configuration: S332D - 20, S331D - 25
Display: VGA monochrome or VGA color LCD (Option 3)
with adjustable backlight
Inputs and Outputs Ports:
RF Out: Type N, female, 50Ω
Maximum Input without Damage: +23 dBm, ± 50 VDC
RF In: Type N, female, 50Ω
Maximum Input without Damage: +43 dBm (Peak), ± 50 VDC
Ext. Trig In: BNC, female (5 V TTL) (S332D Models only)
Ext. Freq Ref In (2 to 20 MHz): Shared BNC, female,
50Ω, (–15 dBm to +10 dBm) (S332D Models only)
T1/E1 (Receive & Transmit): Bantam Jack
(S331D Models with Option 50 only)
Serial Interface: RS-232 9 pin D-sub, three wire serial
Electromagnetic Compatibility: Meets European
Community requirements for CE marking
Safety: Conforms to EN 61010-1 for Class 1
portable equipment
Temperature:
Operating: –10°C to 55°C, humidity 85% or less
Non-operating: –51°C to +71°C (recommended
battery to store separately between 0°C to +40°C
for any prolonged non-operating storage period)
Environmental: MIL-PRF-28800F Class 2
Power Supply:
External DC Input: +12.5 to +15 volt dc, 1350 mA max
Internal: NiMH battery: 10.8 volts, 1800 mAH
Dimensions:
Size (w x h x d): 25.4 cm x 17.8 cm x 6.1 cm
(10.0 in x 7.0 in x 2.4 in)
Weight: <2.28 kg (<5 lbs) includes battery
Basic Models
S331D Cable and Antenna Analyzer (25 MHz to 4.0 GHz)
with built-in DTF
S332D Cable and Antenna Analyzer (25 MHz to 4.0 GHz),
with built-in DTF, Spectrum Analyzer (100 kHz to 3.0 GHz)
510-90
510-91
510-92
510-93
510-96
510-97
Adapter, 7/16 DIN(f)-N(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(f)-N(f), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-N(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-N(f), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(m)-7/16 DIN(m), DC to 7.5 GHz, 50Ω
Adapter, 7/16 DIN(f)-7/16 DIN(f), DC to 7.5 GHz, 50Ω
Standard Accessories Include
User's Guide
Soft Carrying Case
AC-DC Adapter with Power Cord
Automotive Cigarette Lighter/12 Volt DC Adapter
One Year Warranty
Handheld Software Tools CDROM containing Fault Location (DTF)
and Smith Chart
Serial Interface Cable
Rechargeable Battery, NiMH
2000-1030
2000-1031
2000-1032
2000-1200
2000-1035
Portable Antenna, SMA (m), 1.71 to 1.88 GHz, 50Ω
Portable Antenna, SMA (m), 1.85 to 1.99 GHz, 50Ω
Portable Antenna, SMA (m), 2.4 to 2.5 GHz, 50Ω
Portable Antenna, SMA (m), 806-869 MHz, 50Ω
Portable Antenna, SMA (m), 896-941 MHz, 50Ω
1030-86
1030-87
1030-88
1030-89
Band Pass Filter, 806-869 MHz, 1.7 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 902-960 MHz, 1.7 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 1.85-1.99 GHz, 1.8 dB loss, N(m) to SMA(f), 50Ω
Band Pass Filter, 2.4-2.5 GHz, 1.4 dB loss, N(m) to SMA(f), 50Ω
Options
Option 3 Color LCD Display
Option 29 Power Meter (does not require external detector)
Option 50 T1/E1 Analyzer (S331D only)
806-16
806-116
806-117
Bantam Plug to Bantam Plug
Bantam Plug to BNC
Bantam "Y" Plug to RJ48
551-1691
USB to RS232 adapter cable
48258
760-229
633-27
2000-1029
40-163
806-62
800-441
2300-347
Soft Carrying Case
Transit Case
Rechargeable Battery, NiMH
Battery Charger, NiMH, w/ Universal Power Supply
AC/DC Adapter
Automotive Cigarette Lighter/12 Volts DC Adapter
Serial Interface Cable
Software Tools
10580-00079
10580-00100
10580-00101
10580-00102
Site Master S331D/S332D User's Guide
Site Master S331D/S332D Programming Manual
Site Master S331D Maintenance Manual
Site Master S332D Maintenance Manual
Optional Accessories
1N50C
Limiter, N(m) to N(f), 50Ω, 10 MHz to 18 GHz
42N50-20
Attenuator, 20 dB, 5 watt, DC to 18 GHz, N(m)-N(f)
42N50A-30
Attenuator, 30 dB, 50 watt, DC to 18 GHz, N(m)-N(f)
InstaCal™ Calibration Module, 2 MHz to 4.0 GHz, N(m), 50Ω
Open/Short, DC to 18 GHz, N(m), 50Ω
Open/Short, DC to 18 GHz, N(f), 50Ω
Precision Load, DC to 4 GHz, 42 dB, N(m), 50Ω
Precision Load, DC to 4 GHz, 42 dB, N(f), 50Ω
Precision Open/Short/Load, DC to 4 GHz, 42 dB, 50Ω, N(m)
Precision Open/Short/Load, DC to 4 GHz, 42 dB, 50Ω, N(f)
Precision Open/Short/Load, DC to 4 GHz, 7/16 DIN(m), 50Ω
Precision Open/Short/Load, DC to 4 GHz, 7/16 DIN(f), 50Ω
ICN50
22N50
22NF50
SM/PL
SM/PLNF
OSLN50LF
OSLNF50LF
2000-767
2000-768
15NN50-1.5C
15NN50-3.0C
15NN50-5.0C
15NNF50-1.5C
15NNF50-3.0C
15NNF50-5.0C
15ND50-1.5C
Test Port Cable Armored, 1.5 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 3.0 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 5.0 meters, N(m)-N(m), 6 GHz, 50Ω
Test Port Cable Armored, 1.5 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 3.0 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 5.0 meters, N(m)-N(f), 6 GHz, 50Ω
Test Port Cable Armored, 1.5 meters, N(m)-7/16 DIN(m),
6 GHz, 50Ω
15NDF50-1.5C Test Port Cable Armored, 1.5 meters, N(m)-7/16 DIN(f),
6 GHz, 50Ω
Printers
2000-1214
34NN50A
34NFNF50
Precision Adapter, N(m)-N(m), DC to 18 GHz, 50Ω
Precision Adapter, N(f)-N(f), DC to 18 GHz, 50Ω
1091-26
1091-27
1091-80
1091-81
1091-172
Adapter, N(m)-SMA(m), DC to 18 GHz, 50Ω
Adapter, N(m)-SMA(f), DC to 18 GHz, 50Ω
Adapter, N(f)-SMA(m), DC to 18 GHz, 50Ω
Adapter, N(f)-SMA(f), DC to 18 GHz, 50Ω
Adapter, N(m)-BNC(f), DC to 1.3 GHz, 50Ω
2000-753
1091-310
2000-1216
2000-663
2000-664
2000-667
2000-1217
2000-1218
SALES CENTERS:
United States (800) ANRITSU
Canada (800) ANRITSU
South America 55 (21) 2527-6922
Europe 44 (0) 1582-433433
Japan 81 (46) 223-1111
Asia-Pacific (65) 6282-2400
Site Master
™
S331D/S332D
Cable and Antenna Analyzer
25 MHz to 4000 MHz
HP DeskJet Printer, Model 450: Includes printer cable, 2000-1216
black print cartridge and U.S. power cord. Also includes 2000-753
serial-to-parallel Centronics converter cable and 1091-310
Centronics-to DB25 adapter. Rechargeable battery is optional and
is not included.
Null Modem Serial-to-Parallel Centronics Converter Cable
Adapter 36-pin Centronics female-to-DB25 female
Black Print Cartridge
Power Cable (Europe) for DeskJet Printer
Power Cable (Australia) for DeskJet Printer
Power Cable (S. Africa) for DeskJet Printer
Rechargeable Battery for DeskJet Printer, Model 450
Power Cable (U.K.) for DeskJet Printer
Microwave Measurements Division
490 Jarvis Drive, Morgan Hill, CA 95037-2809
http://www.us.anritsu.com
SiteMaster
S331D Site Master
SiteMaster
MS2712
SiteMaster
MS2711D Spectrum Master
MS2712
SpectrumMaster
SpectrumMaster
MT8212A Cell Master
MS2712
CellMaster
©Anritsu October 2003. All trademarks are registered trademarks of
their respective companies. Data is subject to change without notice.
Discover What’s Possible®
CellMaster
PN: 11410-00321, Rev. A
The World’s Leading Cable and Antenna System Analyzer