Digiop BLK-IPS102M User manual

2.0 Megapixel
H.264 Network IP Camera
User Manual
Product: BLK-IPS102M
Please read this manual before using your camera, and always follow the instructions for
safety and proper use. Save this manual for future reference.
BLK-IPS102M_CM
5/27/11
WARNING
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
To reduce the risk of electric shock, do not
remove cover (or back). No user serviceable
parts inside. Refer servicing to qualified
service personnel.

CAUTION
Operate this camera only in environments where the temperature or humidity is within the recommended range.
Operation in extreme temperatures or humidity levels may cause electric shock and shorten the life of the product.
LEGAL NOTICE
DIGIOP® products are designed to meet safety and performance standards with the use of specific DIGIOP
authorized accessories. DIGIOP disclaims liability associated with the use of non-DIGIOP authorized accessories.
The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly
prohibited by law.
DIGIOP makes no representations concerning the legality of certain product applications such as the making,
transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We
encourage you to check and comply with all applicable local, state, and federal laws and regulations before
engaging in any form of surveillance or any transmission of radio frequencies.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. DIGIOP, Inc. disclaims any proprietary interest in trademarks and trade names other
than its own.
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
No part of this document may be reproduced or distributed in any form or by any means without the express written
permission of DIGIOP, Inc.
© 2011 by DIGIOP, Inc. All Rights Reserved.
3850 Priority Way South Drive, Suite 200, Indianapolis, IN 46240
Sales/Support: 1.877.972.2522
ii
www.digiop.com
Table of Contents
SECTION 1
SECTION 2
SECTION 3
APPENDIX A
APPENDIX B
APPENDIX C
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation and Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Tools you need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Mount the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4.1 Audio in/out connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4.2 Sensor in (DI) connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4.3 Alarm out (DO) connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4.4 RS-485 device connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.4.5 LAN and power connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.5 Install IPAdmin Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.6 Configure the camera network settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6.1 Configuring cameras on networks with DHCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6.2 Configuring cameras on networks without DHCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.7 Setup the camera Basic Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.8 Aim, focus, and image quality adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.9 Speaker/microphone setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.10 Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
A.1 Reboot camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
A.2 Set camera to factory default network settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
A.3 Checking your Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
A.4 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Power over Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
B.1 PoE compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
B.2 Power classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.0 Megapixel H.264 Network IP Camera User Manual
1
SECTION 1: FEATURES
SECTION 1
Features
The DIGIOP Black BLK-IPS102M is a professional, premium-grade 2 megapixel, CS-mount box camera designed for indoor use. Lens
and mounting bracket are optional. It features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Aptina™ 1/3.2” (4:3) CMOS 2.0 megapixel sensor
Dual streaming mode
De-interlacing on DSP
Unicast/multicast support
Megapixel compression: H.264/MPEG-4, up to 1600 x 1200 pixels
Video compression: H.264/MPEG-4/MJPEG (dual stream @ D1)
Audio compression: G.711 (µLaw, aLaw)/PCM
Video motion detection support
2-way mono audio support
RTSP/HTTP protocol support
10/100 Base-T Ethernet support
RS485 support
USB 2.0 support (external storage, wireless LAN)
Micro SD card support
PoE support
Built-in video Content Analysis presence, surveillance
OSD support
BLK-IPS102M camera body
2
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
Reset
USB connector
DC jack
adapter
cable
connector
9-pin
terminal
block
LAN
connector
Micro SD
card slot
Back connectors
Reset – For restarting the camera, or resetting the camera to its factory default network settings. Refer to Appendix A,
Troubleshooting, for more information.
USB mini-B connector – For a USB storage device or Wi-Fi networking device
9-pin terminal block – For DI, DO, audio, and serial communication
Power adaptor connector (DC 12V) – For use with the DC jack adapter and the DC12V power adapter (provided).
Micro SD card slot – SD memory card slot for external storage. SD memory card is not included.
LAN connector (Ethernet) – For an RJ-45 LAN cable with 10/100Base-T Ethernet
2.0 Megapixel H.264 Network IP Camera User Manual
3
SECTION 2: INSTALLATION AND SETUP
SECTION 2
Installation and Setup
2.1 What’s in the box
Your camera includes the following:
•
•
•
•
•
•
•
•
•
BLK-IPS102M camera
Cap for protecting the sensor
DC power adapter with power plugs for different powering sources
DC jack adapter cable
Adapter for mounting the camera
9-pin terminal block
Hex wrench
Quick installation guide
CD mini disk with application software, software manual, and camera manual (this document)
2.2 Tools you need
To install the camera, you will need:
•
•
•
•
Phillips #1 or #0 screwdriver
Mounting bracket
Compatible lens
PC with Microsoft® Windows® XP SP3 or newer
NOTE
DIGIOP recommends that a manual iris megapixel lens is used with this camera to support its full resolution.
2.3 Mount the camera
1.
Determine where the camera will be mounted and record the Media Access Control (MAC) address of the camera. The MAC
address can be found on the label on the bottom of the camera. Record the information in the following table.
Location:
MAC address:
4
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
2.
Install the camera mounting bracket using the instructions provided with the bracket.
3.
Attach the adapter for mounting the camera to the side with the label or to the opposite side with the screws provided.
Mounting
adapter
4.
Remove the protective cap covering the camera CCD.
5.
Attach the lens assembly to the camera by screwing it clockwise onto the camera until it is fully seated. The lens may require
a mounting ring adapter to fit onto the camera. Loosen the set screw if necessary.
Mounting ring
2.0 Megapixel H.264 Network IP Camera User Manual
5
SECTION 2: INSTALLATION AND SETUP
6.
Tighten the lens set screw with the hex wrench provided.
7.
Attach the camera to the mounting bracket. Use the instructions provided with the bracket.
2.4 Connections
Connections to the camera for audio in and out (microphone and speaker), DI sensor, DO alarm, and RS‑485 control are made
through the 9-pin terminal block.
9-pin terminal block
Terminal block pin assignments
If the 9-pin terminal block is detached from the camera, plug it into the mating connector on the back of the camera.
2.4.1 Audio in/out connections
The camera includes an interface for a mono audio input (from a microphone) and a mono audio output (to a speaker). The audio
output is a low level signal that requires an amplified speaker (see Specifications). The configuration of the audio wiring (Aout, Ain)
is shown in the following diagram.
6
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
Audio in/out wiring schematic
To connect a speaker and/or microphone to the camera:
1.
Strip 1/4” of insulation from the microphone and speaker wires and insert them into the terminal block in the pin locations
shown in the terminal block figure above. Note that the common (ground) leads of the microphone and speaker share the
same terminal block pin.

CAUTION
Do not attach a headphone or earphone directly to the camera.
2.4.2 Sensor in (DI) connection
The camera provides one channel for sensor input that can be connected to either a voltage type or relay type sensor. For
voltage type sensors, the camera allows an input voltage range of 0 ~ 24 V DC, with a 1 V DC threshold (see Specifications). The
configuration of the sensor input wiring is illustrated in the following schematics.

CAUTION
Do not exceed the maximum input voltage or the relay switching rate. Refer to the specifications in this
manual for more information.
2.0 Megapixel H.264 Network IP Camera User Manual
7
SECTION 2: INSTALLATION AND SETUP
Voltage type sensor wiring schematic
Relay type sensor wiring schematic
To connect a sensor to the camera, strip 1/4” of insulation from the sensor wires and insert them into the terminal block in the DI 1
and C pin locations shown above. The pin marked C in the terminal block is the common (COM) pin.
2.4.3 Alarm out (DO) connection
The camera supports one alarm out connection to relay type device. It provides up to 24 VAC @ 500 mA or 12 V DC @ 1 A. The
configuration of the relay type alarm wiring is illustrated in the diagram below.

CAUTION
8
Do not exceed the maximum relay rating. Refer to the specifications in this manual for more information.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
Relay type alarm wiring schematic
To connect an alarm reporting device to the camera, strip 1/4” of insulation from the alarm wires and insert them into the terminal
block in the DO 1 and C pin locations shown above. The pin marked C on the terminal block is the common (COM) pin.
2.4.4 RS-485 device connection
The camera provides one RS-485 interface connection. The wiring signal polarity to the connector block is shown in the schematic
below.
RS-485 device wiring schematic
To connect an RS-485 device wiring to the camera, strip 1/4” of insulation from the wires and insert them into the terminal block in
the RS-485 pin locations shown above. Observe the signal polarity shown in the schematic.
2.4.5 LAN and power connection
Your camera can be powered locally with a 12 V DC adapter, or across the LAN (PoE, see Appendix B). If using PoE powering, you do
not need to attach a power adapter to the camera.
2.0 Megapixel H.264 Network IP Camera User Manual
9
SECTION 2: INSTALLATION AND SETUP
1.
Attach a LAN cable to the Ethernet connector on the back of the camera. If the camera is powered through the LAN cable,
DO NOT apply power to the camera at this time.
2.
Attach the DC jack adapter cable to the DC 12V power adapter terminals on the back of the camera. Connect the red wire of
the adapter cable to the + terminal, and the black (or white) wire to the - terminal.
DC jack
adapter
cable
3.
Attach the DC jack Adapter to the DC power adapter provided. DO NOT apply power to the camera at this time.
2.5 Install IPAdmin Tool
The IPAdmin Tool, included on the CD mini disk, is a utility that will discover cameras installed on your network and enable you
to perform the initial network setup for each camera. After a camera is setup on the network, the Microsoft Internet Explorer ®
web browser can be used to see video from the camera, set the camera’s password, date and time, finalize camera hardware
adjustments, and configure the camera for functional requirements.
The IPAdminTool can be loaded on a Microsoft Windows XP, Vista or Windows 7 operating system (32- or 64-bit). To use this utility
for the initial setup of your camera, your computer must be connected to the same network subnet as your camera.
At a computer on the same LAN (subnet) where your cameras will be installed, do the following:
1.
Insert the CD mini disk provided with your camera into your computer’s CD ROM drive and open the CD in a Windows
Explorer window.
2.
Find the IPAdminTool directory on the CD.
10
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
3.
Copy the IPAdminTool directory with its contents to your computer hard drive.
2.6 Configure the camera network settings
Devices attached to a Local Area Network (LAN) are each assigned a unique address (IP address) that they use when sending
messages with each other. No two devices on a single Ethernet network can have the same IP address. Otherwise, addressing
conflicts will occur.
When your IP camera is attached to a network and initially powered on, it attempts acquire compatible network settings from
a DHCP server. If it cannot find a DHCP server, it configures itself with the following static IP address, subnet mask, and gateway
setting, which may or may not be compatible with other devices on the network.
IP address:
Subnet mask:
Gateway:
192.168.0.100
255.255.255.0
192.168.0.1
Whether it acquires a dynamic (changeable) IP address and other network settings from a DHCP server, or uses the default static
(fixed, unchanging) settings, your camera must be configured with static network settings that are compatible with the network
configuration. Additionally, if DHCP is not used on your network, DIGIOP Black cameras must be installed on the network and
configured with new network settings one at a time to avoid addressing conflicts.
Use the following procedure to setup and apply compatible, static, network settings for your camera. If connecting your camera to a
large enterprise network, consult with your network administrator for network settings before attaching the camera to the LAN to
ensure that your camera won’t conflict with other devices. Your network administrator should also setup WAN (Internet) access to
the camera, if that is needed.
If you encounter a problem and need to contact Technical Support, first complete the chart in Table 1 about your computer (PC) and
camera network settings, if possible. Support will need this information to provide assistance.
2.6.1 Configuring cameras on networks with DHCP
In networks with a DHCP server, the IP camera will acquire dynamic (changeable) network settings when it is initially powered on.
These dynamic settings can easily be converted to static settings, or changed to other static settings that are also compatible with
your network.
1.
Connect your camera to the LAN, then power on the camera.
2.
Open the IPAdminTool directory on your computer, then double click the file IPAdminTool.exe to start the application.
When the IPAdmin Tool starts, it will discover all the IP devices it supports that exist on the network. The discovery process
may take a few minutes.
2.0 Megapixel H.264 Network IP Camera User Manual
11
SECTION 2: INSTALLATION AND SETUP
Check the list of IP devices found by IPAdmin Tool. You can identify your camera by the MAC address. If the camera was not
found, click the Refresh button every minute until your camera appears in the list.
3.
In the IPAdmin Tool device list, use the camera’s MAC Address to find the camera you are installing. After finding the camera,
right click the entry, then select IP Address from the drop-down list. An IP Setup window will open.
4.
In the IP Setup window, click the Static option bullet to select this option.
Static
Option
12
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
If you have other compatible, network settings you want to apply to the device, enter them in the appropriate locations. Click
Setup to save settings.
5.
In the Login window, enter the ID and PW (password) for your camera and click Login. The default administrator values for
the ID and PW are root and pass. After entering ID and PW, the IP Setup window closes.
6.
In the IPAdmin Tool window, click Refresh and verify that the entry representing the camera now shows the new IP address.
7.
Continue with procedure 2.7 Setup camera Basic Configuration.
2.6.2 Configuring cameras on networks without DHCP
Cameras installed on a network without a DHCP server will initially use the factory default static network settings:
IP address:
Subnet mask:
Gateway:
192.168.0.100
255.255.255.0
192.168.0.1
In networks without a DHCP server, cameras must be powered on and reconfigured one at a time to avoid addressing conflicts
between other cameras, or possibly with another device on the network. Configuring the network settings of your cameras includes
these steps:
——
——
——
——
Determine the network settings of your computer.
Check the network for compatibility with the default static network settings of your camera.
Find network settings (IP addresses) that are not in use and can be assigned to your camera.
Attach your camera to the network, power it on, and configuring it with new network settings.
Determine the network settings of your computer
1.
At a PC attached to the same LAN that will be shared with your camera, determine the IP address, subnet mask, and default
gateway of your PC and record it in Table 1. To find this information, do the following at the Windows desktop:
a.
Hold down the Windows key and press r to open the Run dialog box.
2.0 Megapixel H.264 Network IP Camera User Manual
13
SECTION 2: INSTALLATION AND SETUP
b.
Type cmd in the entry field, then click OK to open the DOS command window.
c.
At the command prompt, enter ipconfig. The response will show the your PC’s network settings.
Example: Typical use of ipconfig in Windows XP
d.
Enter the IP Address, Subnet Mask, and Default Gateway for your PC’s Ethernet adapter into Table 1.
NOTE
The Ethernet adapter data you see by using ipconfig will probably be different from that shown in the example
above. If you are using Windows Vista or Windows 7, the IP address is identified as the “IPv4 Address.”
Table 1. PC/Camera network settings
Computer (PC)
Camera
IP Address
Subnet Mask
Default Gateway

CAUTION
14
If connecting your camera to an enterprise network, consult with your network administrator for the
camera IP address, subnet mask, and default gateway.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
Find network settings (IP addresses) that are not in use
1.
At your PC, find an IP address on your network that is not in use:
a.
Write down the EXACT IP address of your PC up to the third/last period. Using the example shown above, this
expression is: 192.168.1.
b.
After the third period, include any number between 1 and 254 that is different from the one in your PC’s IP address,
168. As a first try, let’s choose 200, which will form the IP address 192.168.1.200.
c.
Next, use the ping command in the DOS window to see if this IP address is in use on your network. The format of the
ping command is:
ping <IP address>
To test this IP address, enter ping 192.168.1.200. Any reply received from the ping indicates that a device on the
network is already using this IP address and you can connect to it.
In the example shown above, the message “Reply from 192.168.1.200: ..” indicates that your PC can reach the
device with that IP address, and that address is in use (i.e., you cannot use it for your camera).
d.
Since the ping test of the IP address we tried showed the address was in use, try another number between 1 and 254.
For example, let’s ping 192.168.1.201. At the DOS prompt, enter: ping 192.168.1.201
2.0 Megapixel H.264 Network IP Camera User Manual
15
SECTION 2: INSTALLATION AND SETUP
e.
In this test, the message “Request timed out” indicates that your PC cannot reach the device with that IP address, and
that address is probably not in use. Enter this number into Table 1. If this test indicated that this IP address is in use, try
other IP addresses using the steps above until an unused address is found.
Check LAN for default IP address compatibility
Because all DIGIOP Black cameras and encoders are factory configured with the static IP address 192.168.0.100, check the LAN
before connecting your camera to ensure that network conflicts won’t occur.
At a Microsoft Windows computer attached to the LAN subnet where the camera will be connected, open a Command Prompt
window and enter:
ping 192.168.0.100
The “Request timed out” response indicates that the IP address is not in use and the camera can be connected without causing
errors.
Attach your camera to the network and power it on
Apply power to the camera. When the camera powers on, it performs an internal initialization, then establishes a connection to the
LAN. Wait until the initialization process completes before continuing. It may take up to 3 minutes for your camera to initialize.
Configure the camera IP address
1.
16
Open the IPAdminTool directory on your computer, then double click the file IPAdminTool.exe to start the application.
When the IPAdmin Tool starts, it will discover all the IP devices it supports that exist on the network. The discovery process
may take a few minutes.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
2.
In the Product list, find the entry with the same MAC address as the camera you installed. If the camera is not shown, click
Refresh once a minute to update the list.
3.
Right click on the entry for your camera and select IP Address.
IP Setup window
4.
5.
In the IP Setup window:
a.
Select the Static option if it is not selected. This option is required if video from the camera will be recorded by a
network DVR, or if you want to view video from the camera across a WAN (Internet).
b.
Enter the IP address for your camera from Table 1 into the IP Address field.
c.
Enter the subnet mask for your computer from Table 1 into the Subnet Mask field.
d.
Click SETUP. A Login window will open.
In the Login window, enter the ID and PW (password) for your camera, then click Login. The default administrator ID and
PW are root and pass. After entering the ID and PW, the IP Setup window closes.
2.0 Megapixel H.264 Network IP Camera User Manual
17
SECTION 2: INSTALLATION AND SETUP
6.
In the IPAdmin Tool window, click Refresh and verify that the entry representing the camera now shows the new IP address.
7.
In the IPAdmin Tool window, click Refresh and verify that the entry for your camera now shows the new IP address.
2.7 Setup the camera Basic Configuration
In this procedure, Microsoft Internet Explorer (IE) browser is used to setup the camera administrator and user passwords, date, and
time.
1.
Open the IE browser.
2.
In the URL field (Internet address), enter the IP address for your camera in the format:
http://<IP address>/
where <IP address> is the IP address of your camera. Following the example earlier in this guide, the entry would be:
http://192.168.1.201
3.
If prompted to install an ActiveX control such as AxNVC.cab, follow screen prompts to install the software.
IE prompt to install ActiveX control
NOTE
18
To load these ActiveX controls, you may need to adjust the security settings of your browser to accept add-ins from
unknown publishers.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
Typical initial camera view
NOTE
If, after logging into your camera, you cannot see live video and the message:
“Can not Create XMLDOMDocument Install MSXML4.0” appears, download and install the MS XML 4.0 library. This library can
be found at:
http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B-B4F2-46DA-B4B6-C5D7485F2B42&displaylang=en
4.
In the camera window, click the SETUP link in the upper right corner of the window. Enter the User name and Password for
the camera, and click OK. The default administrator values are root and pass. The Basic Configuration window will open.
5.
Under the Basic Configuration menu, click Date & Time. In the Date & Time Setting options:
a.
Select the Time Zone you prefer.
2.0 Megapixel H.264 Network IP Camera User Manual
19
SECTION 2: INSTALLATION AND SETUP
b.
Select the synchronization method, or Set Manually bullet and enter the appropriate information.
c.
Select the Sync Source and Interval you prefer.
d.
Click Apply.
6.
In the Basic Configuration menu, click Users.
7.
In the User List, click root, and then click Modify and follow the prompts. Setup the root user with a new password and
click OK.
20
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
8.
In the Users menu, click Apply, then click OK to restart the webserver (if you wish to do so at this time).
9.
Click Add to include other administrators, operators or viewers to the user list. Follow the screen prompts to complete the
entries.
10. Click VIEW in the upper right corner of the window to return to the camera live view.
2.8 Aim, focus, and image quality adjustments
Use the documentation provided with your camera mounting bracket and lens to aim the camera at your security target and,
depending on the attached lens, set focus and zoom, while observing the video image from the camera.
Adjustments to the image brightness, contrast, hue, saturation, and sharpness are performed through the web browser:
1.
From the View window, click: SETUP > Video & Audio > Video-In
2.0 Megapixel H.264 Network IP Camera User Manual
21
SECTION 2: INSTALLATION AND SETUP
2.
Scroll to the bottom of the screen and click the PREVIEW button. Follow the screen instructions to open the camera view in
another IE window.
3.
While observing the video in the PREVIEW window, adjust the values for brightness, contrast, hue, saturation, sharpness,
and/or other parameters on screen. Click Apply to see the effect of the change. Make any necessary adjustments to produce
the best video image.
4.
Close the PREVIEW window and click VIEW to return to the normal viewing window.
2.9 Speaker/microphone setup
Verify the functionality of the speaker and microphone setup at the camera, and adjust volume levels.
1.
22
On the VIEW screen, click SETUP > Video & Audio > Audio to open the Bi-directional Audio Settings menu.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
2.
In the Bi-directional Audio Settings menu, click the checkboxes to select “Listen to the audio from server with setting
below” and “Talk to the speakers of server”.
3.
Click Apply, and then click VIEW to return to the camera view screen.
4.
On the VIEW screen, check the SPK and MIC options to enable the speaker at the camera and the microphone on your
computer.
5.
At your computer, listen for sounds from the microphone at the camera. If necessary, adjust the volume from the camera.
Click: SETUP > Video & Audio > Audio
to re-open the Bi-directional Audio Settings menu. In the Listen frame, adjust the volume to the preferred level. Click Apply.
6.
Use a microphone at your PC to send audio to the camera speakers. Verify that your microphone audio is heard at the speaker.
To adjust the speaker volume go to the Bi-directional Audio Settings menu. In the Talk to frame, adjust the volume to the
preferred level. Click Apply.
2.0 Megapixel H.264 Network IP Camera User Manual
23
SECTION 2: INSTALLATION AND SETUP
2.10 Cleaning
Clean the camera housing with an approved glass cleaning solution and a lint free cloth.
•
•
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub the surface with a soft
cloth moistened with a mild detergent solution, then rinse and dry it with a soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing. These may cause damage
to the surface over time.

CAUTION
24
Do not use benzene, thinner or other chemical products on the camera assembly; these may dissolve the paint and
promote damage of the surfaces. Before using any chemical product, read the accompanying instructions carefully.
www.digiop.com
SECTION 3: SPECIFICATIONS
SECTION 3
Specifications
Table 2.Specifications
Camera Module
Image Sensor
Aptina (Micron®) 1/3.2” (4:3) CMOS 2M
Effective Pixels
1600 x 1200 (UXGA, 2M)
Scanning system
Progressive scan
Dynamic Range
71 dB
SNR
Max 42.3 dB
Minimum Illumination
0.5 Lux (50 IRE), 0.1 Lux (DSS x5 ON)
Lens (Optional)
CS mount
Day & Night
S/W
Video
Megapixel Compression
H.264 and MJPEG
Compression Format
H.264, MPEG-4, and MJPEG
Number of Streams
Dual Stream, Configurable
Resolution
See Resolutions table below
Compression FPS (If VCA
or Burnt-in Annotation is
on, fps could be less.)
H.264
5 fps @ UXGA (1600 x 1200), 8 fps @ SXGA (1280 x 1024),
12 fps @ HD720 (1280 x 720), 15 fps @ XGA (1024 x 768), D1 (720 x 480)
MJPEG
15 fps @ UXGA (1600 x 1200)
MPEG4
15 fps @ D1 (720 x 480)
Motion detection
Support (DSP)
Burnt-in text
Support (DSP)
Video output
Not available
Audio
Input/output
1/1 channel
Compression format
G.711
Function
Digital input
1 channel (dry and wet contact selectable)
Digital output
1 channel (dry contact)
RS-485
Support
RS-232
Not available
Network
10/100Base-T
2.0 Megapixel H.264 Network IP Camera User Manual
25
SECTION 3: SPECIFICATIONS
Protocol
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP, SNTP, mDNS, UPnP, SMTP, SOCK, IGMP, DHCP, FTP, DDNS, SSL
v2/v3, IEEE 802.1X, SSH
USB 2.0
Support (Mini-B plug)
SD slot
Supported (microSD type, not included)
Electrical Characteristics
Audio input
Line-in, 1.43 Vp-p (min 1.35 Vp-p, max 1.49 Vp-p), 39 KΩ
Audio output
Line-out, 46 mW Power, 16 Ω
Sensor (D/I)
TTL level 4.5 V threshold, max 50 mA
Alarm (D/O)
Max 500 mA @ 24 V AC or 1A @ 12 V DC
Power source (approx.)
12 V DC (screw terminal)
Power over Ethernet (PoE)
300 mA @ +12 V
Power consumption (approx.)
300 mA @ +12 V
Mechanical characteristics
Material
Aluminum (die-casting)
Color
White pearl
Dimensions
2.17” (W) x 2.17” (H) x 3.60” (L)
Weight
0.57 lbs (approx.)
Environmental Conditions
Operating Temperature
(32˚F ~ 122˚F (0˚C ~ 50˚C)
Operating Humidity
Up to 85% RH (Non-condensing)
Table 3.Resolutions per codec frame rate
Resolution
MPEG4
H.264
UXGA (1600 x 1200)
Not available
5 fps
SXGA (1280 x 1024)
Not available
8 fps
HD720 (1280 x 720)
Not available
12 fps
XGA (1024 x 768)
Not available
D1 (720 x 480)
15 fps
4CIF (704 x 576)
VGA (640 x 480)
CIF (352 x 288)
15 fps
QVGA (320 x 240)
QCIF (176 x 144)
26
MJPEG
www.digiop.com
15 fps
SECTION 3: SPECIFICATIONS
Table 4.Video Content Analysis (optional)*
VCA Presence
High Performance
Advanced tracking algorithm, low false alarm rate
Easy to Use
Intuitive web browser interface
Detection Zones
Multi-segment polygons and lines
On-screen Display
Real-time display of tracking data and events
Burnt-in Annotation
Stream
Image Stabilization
Electronic Stabilization
Removes camera sway
* Other VCA options are available. Call for details.
2.0 Megapixel H.264 Network IP Camera User Manual
27
APPENDIX A: TROUBLESHOOTING
APPENDIX A
Troubleshooting
A.1 Reboot camera
NOTE
The reboot process lasts about 2 minutes, during which time the camera will not respond to the IPAdmin Tool or transmit video to
a web browser
The camera can be rebooted in two ways:
•
•
Using the IPAdmin Tool:
a.
Start the IPAdmin Tool.
b.
Find the entry for the camera you want to reboot and click it to select (highlight) it.
c.
Click the Reboot button and enter the administrator ID and PW.
d.
Click Refresh to re-discover the camera.
Using the reset button on the camera:
a.
Press and hold the reset button on the camera for 5 seconds.
b.
Click Refresh to re-discover the camera.
A.2 Set camera to factory default network settings
The camera network settings can be forced to the factory default values:
Network settings acquired through DHCP on networks with DHCP
- OR Network settings forced to the following on networks were a DHCP server cannot be found:
——
——
——
——
——
28
IP address – reset to 192.168.0.100
Subnet mask – reset to 255.255.0.0
Gateway – reset to 192.168.0.1
User ID – reset to root
Password – reset to pass
www.digiop.com
APPENDIX A: TROUBLESHOOTING
To force the camera to the factory network settings:
1.
Disconnect the power (adapter) from the camera.
2.
While pressing and holding down the reset button, power on the camera.
3.
Release the Reset button 5 seconds after applying power.
4.
Wait for the camera to reboot.
A.3 Checking your Firmware
Firmware is software embedded in the camera that determines many of its features and functionality. The current firmware version
number in your camera can be found by viewing video from the camera in IE, and then clicking SETUP > About > Version.
Contact DIGIOP Support for up to date firmware.
A.4 Support
If you cannot resolve an issue, please contact DIGIOP Support at 1.877.972.2522 for assistance. When you contact support, please
provide the server reports, log file and a brief description of the problem, if possible.
•
To generate server reports, enter the following into the IE address field:
https://<IP ADDRESS>/nvc-cgi/admin/param.cgi?action=list
- and https://<IP ADDRESS>/nvc-cgi/admin/vca.cgi?action=list
where <IP ADDRESS> is the IP address of your camera. The server report contains important information about the device,
as well as a list of the current parameters.
•
To generate a log report, use IE to log into the unit. In the View screen, click the following items, entering security
information when required:
SETUP > Maintenance > System Log > LOG LIST
Click the name of the Log List of interest to open it.
2.0 Megapixel H.264 Network IP Camera User Manual
29
APPENDIX B: POWER OVER ETHERNET
APPENDIX B
Power over Ethernet
The BLK-IPS101 camera supports Power over Ethernet (PoE) in conformance with the IEEE 802.3af standard. IEEE 802.3af allows for
two power options for Category 5 cables.
The PoE module signature and control circuit provides the PoE compatibility signature and power classification required by
the Power Sourcing Equipment (PSE) before applying up to 15 W power to the port.
The high efficiency AC/DC converter operates over a wide input voltage range and provides a regulated low ripple and low
noise output. The AC/DC converter also has built-in overload and short-circuit output protection.
•
•
B.1 PoE compatibility
With non Power Sourcing Equipment (PSE)
When it is connected with non PSE, use the power adaptor to provide power to the camera.
With power adaptor
Connecting both PSE and power adaptor does not do any harm to the products. Disconnecting power adaptor while it is operating
does not stop operation. The product continues to work without rebooting.
B.2 Power classification
The PoE Power Class supported by the IP device is Class 0.
Class
Usage
Minimum Power Levels Output at the PSE
Maximum Power Levels at the Powered Device
0
Default
15.4 W
0.44 to 12.95 W
30
www.digiop.com
APPENDIX C: DIMENSIONS
APPENDIX C
Dimensions
2.0 Megapixel H.264 Network IP Camera User Manual
31