Mitsubishi GT10 Specifications

JY997D25301F
Side
B
Side
Side
A
B
JAPANESE
ENGLISH
GT1030-LBD†, GT1030-LBD†2
GT10 General Description
Manual Number
JY997D25301F
Date
Sep 2008
This manual describes the specifications of the product. Before use, read this
manual and manuals of relevant products fully to acquire proficiency in handling
and operating the product. Make sure to learn all the product information, safety
information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are
the registered trademarks or trademarks of each company.
Effective Sep 2008
Specifications are subject to change without notice.
© 2008 Mitsubishi Electric Corporation
• Use the GOT in the environment that satisfies the general specifications
described in this manual. Not doing so can cause an electric shock, fire,
malfunction or product damage or deterioration.
• When mounting the GOT to the control panel, tighten the mounting screws in the
specified torque range. Undertightening can cause the GOT to drop, short circuit
or malfunction. Overtightening can cause a drop, short circuit or malfunction due
to the damage of the screws or the GOT.
WIRING PRECAUTIONS
• Be sure to shut off all phases of the external power supply used by the system
before wiring. Failure to do so may result in an electric shock, product damage or
malfunctions.
• Please make sure to ground FG terminal of the GOT power supply section by
applying 100 or less which is used exclusively for the GOT. Not doing so may
cause an electric shock or malfunction.
• Correctly wire the GOT power supply section after confirming the rated voltage
and terminal arrangement of the product. Not doing so can cause a fire or failure.
• Tighten the terminal screws of the GOT power supply section in the specified
torque range. Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the
screws or the GOT.
• Exercise care to avoid foreign matter such as chips and wire offcuts entering the
GOT. Not doing so can cause a fire, failure or malfunction.
Before using this product, please read this manual and the relevant manuals introduced
in this manual carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "DANGER" and "CAUTION".
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
• Before performing the test operations of the user creation monitor screen (such as
turning ON or OFF bit device, changing the word device current value, changing
the settings or current values of the timer or counter), read through the manual
carefully and make yourself familiar with the operation method.
During test operation, never change the data of the devices which are used to
perform significant operation for the system. False output or malfunction can
cause an accident.
• When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
• Connect the battery correctly.
Do not discharge, disassemble, heat, short, solder or throw the battery into the fire.
Incorrect handling may cause the battery to generate heat, burst or take fire,
resulting in injuries or fires.
• Before starting cleaning or terminal screw retightening, always switch off the
power externally in all phases. Not switching the power off in all phases can cause
a unit failure or malfunction. Undertightening can cause a short circuit or
malfunction. Overtightening can cause a short circuit or malfunction due to the
damage of the screws or unit.
• Be sure to shut off all phases of the external power supply used by the
system before mounting or removing the GOT to/from the panel.
Not doing so can cause the unit to fail or malfunction.
• When installing the battery wear an earth band etc. to avoid the static electricity.
The static electricity can cause the unit to fail or malfunction.
STARTUP/MAINTENANCE
PRECAUTIONS
• Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
• Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
• The cables connected to the unit must be run in ducts or clamped.
Not doing so can cause the unit or cable to be damaged due to the dangling,
motion or accidental pulling of the cables or can cause a malfunction due to a
cable connection fault.
• When unplugging the cable connected to the unit, do not hold and pull the cable
portion. Doing so can cause the unit or cable to be damaged or can cause a
malfunction due to a cable connection fault.
• Do not drop or apply any impact to the battery.
If any impact has been applied, discard the battery and never use it.
The battery may be damaged by the drop or impact.
• Before touching the unit, always touch grounded metal, etc. to discharge static
electricity from human body, etc.
Not doing so can cause the unit to fail malfunction.
DISPOSAL PRECAUTIONS
• When disposing of the product, handle it as industrial waste.
Specifications
Item
GT1030-LBD/LBD2/LBDW/LBDW2
0 to 50°C
Other than display section
Storage ambient temperature
0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)
-20 to 60°C
Operating ambient humidity
10 to 90% RH, non-condensing (The wet bulb temperature is 39°C or less.)
Storage ambient humidity
10 to 90% RH, non-condensing (The wet bulb temperature is 39°C or less.)
Frequency
Conforms to JIS
B3502 and
IEC61131-2
Vibration resistance
Shock resistance
Operating altitude
EN61131-2 : 2003
Programmable controllers- Equipment, requirement
and tests
Under intermittent
vibration
Under continuous
vibration
Acceleration
Half-amplitude
5 to 9Hz
--
3.5mm
9 to 150Hz
9.8m/s2
--
5 to 9Hz
--
1.75mm
9 to 150Hz
4.9m/s2
--
Sweep Count
EMS
Compliance with all relevant aspects of the standard.
(ESD,RF electromagnetic field, EFTB, Surge, RF conducted disturbances and Power frequency magnetic field)
Existing Cables
GT1030-LBD, GT1030-LBDW
GT10-C30R4-8P (For Melsec FX series PLC)
GT1030-LBD2, GT1030-LBDW2
GT10-C30R2-6P (For Melsec Q series PLC)
2) General notes on the use of the power cable
The GT1030-LBD/LBD2/LBDW/LBDW2 unit demand that the cable for the power supply is 10m or less.
Associated Manuals
Contents
Manual Number
(Model Code)
GT10 User's Manual
(sold separately)
Describes the GT10 hardware-relevant content such as part names, external dimensions,
mounting, power supply wiring, specifications, and introduction to option devices
JY997D24701
(09R819)
GOT1000 Series Connection Manual 1/3, 2/3, 3/3
(sold separately) *1
Describes system configurations of the connection method applicable to GOT1000 series
and cable creation method
SH-080532ENG
(1D7M26)
GT Designer2 Version2 Basic Operation/Data Transfer
Describes methods of the GT Designer2 installation operation, basic operation for drawing
Manual (For GOT1000 Series)
and transmitting data to GOT1000 series
(sold separately) *1
SH-080529ENG
(1D7M24)
GT Designer2 Version2 Screen Design Manual
(For GOT1000 Series) 1/3, 2/3, 3/3
(sold separately) *1
SH-080530ENG
SH-080531ENG
(1D7M25)
Describes specifications and settings of the object functions used in GT Designer2
*1 Stored in the GT Works 2/GT Designer2 in PDF format.
For details of a PLC to be connected, refer to the PLC user's manual respectively.
Bundled Items
Model Name
Explanation of the GOT model name
Remark
GT10 2 0 -
GT1030-LBD
GT1030-LBD2
GT1030-LBDW
GT1030-LBDW2
Maintenance Supplies
Quantity
PLC Communication Connector
1
Panel Mounting Bracket (with M4 × 20 screws)
4
Panel Mounting Packing
1
GT10 General Description (This manual)
1
2:RS-232
Interface type for
communication with PLC Blank:RS-422
Backlight type
W:white/red/pink
Blank:green/red/orange
Power type
D:24VDC
L:5VDC
B:Black
Panel color type
Display device type L:STN monochrome
0:Monochrome(black/white)
Display color type
Screen size type
3:4.5"
2:3.7"
GOT1000 series
GT10
*2 For the details of system information, refer to the following.
GT Designer2 Version† Screen Designer Manual
*3 ROM in which new data can be written without deleting the written data.
*4 Note that this does not guarantee all users' operation environment.
1.3 Communication Specifications
Specifications
Item
2000 m (6562 ft) max.
* * * * *
GOT main unit
(The maintenance supplies below are packed with the product.)
10 times each in X,
Y and Z directions
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electroconductive dust particles and
must be no direct sunlight. (Same as for saving)
*1
Compliance with all relevant aspects of the standard.
(Radiated Emissions)
1) General notes on the use of communication cables
Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise. Therefore, when installing any communication cables care
should always be taken with the routing and location of those cables. The GOT units identified on the previous chapter are compliant with the EMC requirement when the
following communication cables are used.
GT1030-LBD/LBDW
Communication standard
PLC communication
Conforms to JIS B3502, IEC 61131-2 (147m/s2, 11 ms, Sine half-wave pulse, 3 times each in the X, Y, and Z directions.)
Operating atmosphere
Remark
EMI
*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal
display panel. It is impossible to completely avoid this symptom, as the liquid
crystal display comprises of a great number of display elements. Flickers may
be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not
caused by product defect.
When the same screen is displayed for a long time, an incidental color or
partial discoloration is generated on the screen due to heat damage, and it
may not disappear.
To prevent heat damage, the screen saver function is effective.
For details of the screen saver function, refer to the following.
GT10 User's Manual
1.1 General Specifications
Display section
Standard
Manual name
1. Specifications
Operating ambient
temperature
The following products have shown compliance through direct testing (to the identified standards) and design analysis (forming a technical construction file) to the European
Directive for Electromagnetic Compatibility (89/336/EEC) when used as directed by the appropriate documentation.
Type :Programmable Controller (Open Type Equipment)
The following manuals are relevant to this product. When these loose manuals are required, please consult with our local distributor.
• Some failures of the GOT or cable may keep the outputs on or off.
An external monitoring circuit should be provided to check for output signals
which may lead to a serious accident.
Not doing so can cause an accident due to false output or malfunction.
• If a communication fault (including cable disconnection) occurs during
monitoring on the GOT, communication between the GOT and PLC CPU is
suspended and the GOT becomes inoperative.
A system where the GOT is used should be configured to perform any
significant operation to the system by using the switches of a device other
than the GOT on the assumption that a GOT communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
• Do not use the GOT as the warning device that may cause a serious accident.
An independent and redundant hardware or mechanical interlock is required to
configure the device that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect
output or malfunction.
• Incorrect operation of the touch switch(s) may lead to a serious accident if the
GOT backlight is gone out.
When the GOT backlight goes out, causes the monitor screen to appear
blank, while the input of the touch switch(s) remains active.
This may confuse an operator in thinking that the GOT is in "screensaver"
mode, who then tries to release the GOT from this mode by touching the
display section, which may cause a touch switch to operate.
MOUNTING
PRECAUTIONS
Requirement for Compliance with EMC directive
GOT Unit
TEST OPERATION
PRECAUTIONS
STARTUP/MAINTENANCE
PRECAUTIONS
• Do not bundle the control and communication cables with main-circuit, power
or other wiring.
Run the above cables separately from such wiring and keep them a minimum
of 100mm (3.94in.) apart.Not doing so noise can cause a malfunction.
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive for the entire mechanical module should be checked by
the user / manufacturer. For more details please contact the local Mitsubishi Electric
sales site.
Notes for compliance to EMC regulation
• Plug the communication cable into the connector of the connected unit and
tighten the mounting and terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction. Overtightening can
cause a short circuit or malfunction due to the damage of the screws or unit.
DESIGN PRECAUTIONS
DESIGN PRECAUTIONS
• Before transporting the GOT, turn the GOT power on and check that the battery
voltage status is normal on the Time setting & display screen (utilities screen). In
addition, confirm that the adequate battery life remains on the rating plate.
Transporting the GOT with the low battery voltage or the battery the reached
battery life may unstabilize the backup data unstable during transportation.
• Make sure to transport the GOT main unit and/or relevant unit(s) in the manner
they will not be exposed to the impact exceeding the impact resistance
described in the general specifications of this manual, as they are precision
devices. Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
For more details please contact the local Mitsubishi Electric sales site.
WIRING PRECAUTIONS
Safety Precaution (Read these precautions before using.)
Compliance with EC directive (CE Marking)
TRANSPORTATION
PRECAUTIONS
MOUNTING PRECAUTIONS
PC communication*1
GT1030-LBD2/LBDW2
RS-422 1ch
RS-232 1ch
Transmission speed
115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
Connector terminal block 9-pins
Communication standard
RS-232 1ch
Transmission speed
115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
MINI DIN 6-pins (Female)
Installation location
Inside control panel
Overvoltage category*2
II or less
Pollution degree*3
2 or less
1.4 Power Supply Specifications
Cooling method
Self-cooling
(For details on power supply wiring, such as the allowable cable size and tightening torque, refer to the additional manual, "GT10 User's Manual".)
*1 Project data upload/download, OS installation, Transparent function
*1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
*2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
1.2 Performance Specifications
Specifications
Item
Display
section*1
24VDC (+10% -15%), ripple voltage 200mV or less
Fuse (built-in, not exchangeable)
0.5A
Power consumption, (At backlight off)
2.2W (90mA/24VDC) or less, (1.7W (70mA/24VDC) or less)
Inrush current
18A or less (26.4VDC) 1ms
Permissible instantaneous power failure
Within 5ms
time*1
STN monochrome (white/black) liquid crystal
Noise immunity
Noise voltage: 1000Vp-p, Noise width: 1µs (by noise simulator of 30 to 100Hz noise frequency)
4.5"
Dielectric withstand voltage
500VAC for 1 minute (between the GOT’s power supply terminals and the GOT’s grounding terminal)
Resolution
288 × 96 dots (Horizontal format)
Insulation resistance
10MΩ or larger by insulation resistance tester (between the GOT’s power supply terminals and the GOT’s grounding terminal)
Display size
W109.42(4.3) × H35.98(1.41) [mm](inch) (Horizontal format)
Grounding
Class D grounding (100Ω or less). To be connected to the panel when grounding is not possible
Display character
16-dot standard font: 36 characters × 6 lines, 12-dot standard font: 48 characters × 8 lines (Horizontal format)
Display color
Monochrome (white/black)
Display angle
Left/Right: 30 degrees, Top: 20 degrees, Bottom: 30 degrees (Horizontal format)
Contrast adjustment
16-level adjustment
Intensity of LCD only
200 [cd/m2] (in green)
Intensity adjustment
8-level adjustment
300 [cd/m2] (in white)
Approx. 50,000h. (Time for display intensity to become 1/5 at operating ambient temperature of 25°C)
LED with 3 available colors (green, red, orange)
*1 The GOT continues to operate even upon 5ms or shorter instantaneous power failure.
The GOT stops operating if there is extended power failure or voltage drop, while it automatically resumes operation as soon as the power is restored.
2. Wiring of connection cable
The diagram below shows cable assignment for GOT port.
Cables: GT10-C†††R4-8P, GT10-C†††R4-2P, GT10-C†††R2-6P
GOT
PLC
LED with 3 available colors (white, red, pink)
PLC connection cable
This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Backlight status (colors, ON/BLINK/OFF) control, Adjustable screensaver activation time
Setting the system information enables*2 PLC to control the backlight status
Number of touch keys
Maximum 50 keys/screen (Matrix resistive film touch panel)
Key size
Minimum 16 × 16 dots (per key)
Simultaneous pressing of
two (or more) areas
Enable
(2-point press)
Life
1 million times or more (operating force 0.98N max.)
User memory*3
Flash memory ROM (Internal), for storing Project data (1.5M bytes or less), OS
Life
(Number of write times)
100,000 times
GT11-50BAT lithium battery
Battery
Input power supply voltage
Screen size
Life
Memory
GT1030-LBDW/LBDW2
GT1030-LBD/LBD2/LBDW/LBDW2
Type
Backlight
(no replacement required)
Touch
panel
GT1030-LBD/LBD2
Specifications
Item
Backup target
Clock data, alarm history and recipe data
Life
Approx. 5 years (Operating ambient temperature of 25 )
Buzzer output
(a buzzer that sounds when touch Single tone (LONG/ SHORT/ OFF adjustable)
keys are pressed)
Environmental protective structure*4
Equivalent to IP67 (JEM1030) (front section)
External dimensions
W145(5.7) × H76(2.99) × D29.5(1.16)[mm](inch) (Excluding mounting fixtures) (Horizontal format)
Panel cutting dimensions
W137 (5.39) × H66 (2.59) [mm] (inch) (Horizontal format)
Weight
0.3kg (Excluding mounting fixtures)
Compatible software package
GT Designer2 Version2.58L or later
GT10-C
R4-8P
GOT
(terminal
block)
SDA
SDB
RDA
RDB
SG
RSA
RSB
CSA
CSB
GT10-C
Untied
wire
color
GOT
(terminal
block)
Brown
Red
Orange
Yellow
Green
Black
White
SDA
SDB
RDA
RDB
SG
RSA
RSB
CSA
CSB
GT10-C
R4-25P
Untied
wire
color
R2-6P
GOT
(terminal
block)
Brown
Red
Orange
Yellow
Green
Blue
Purple
Black
White
SD
RD
ER
DR
SG
RS
CS
NC
NC
Untied
wire
color
Brown
Red
Blue
Yellow
Green
Purple
User-made cable is necessary, depending on the PLC.
For the detail, refer to GOT1000 Series Connection Manual.
Cable jacket to remove
7mm (0.27")
Tightening torque
0.22 to 0.25 N•m
Recommended Tool
(Screwdriver)
SZS 0.4 × 2.5
(Phoenix Contact Inc.)
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For safe use
• This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
• This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310,
JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN
JY997D25301F
Side
B
Side
Side
A
B
JAPANESE
ENGLISH
GT1030-LBD†, GT1030-LBD†2
GT10 General Description
Manual Number
JY997D25301F
Date
Sep 2008
This manual describes the specifications of the product. Before use, read this
manual and manuals of relevant products fully to acquire proficiency in handling
and operating the product. Make sure to learn all the product information, safety
information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are
the registered trademarks or trademarks of each company.
Effective Sep 2008
Specifications are subject to change without notice.
© 2008 Mitsubishi Electric Corporation
• Use the GOT in the environment that satisfies the general specifications
described in this manual. Not doing so can cause an electric shock, fire,
malfunction or product damage or deterioration.
• When mounting the GOT to the control panel, tighten the mounting screws in the
specified torque range. Undertightening can cause the GOT to drop, short circuit
or malfunction. Overtightening can cause a drop, short circuit or malfunction due
to the damage of the screws or the GOT.
WIRING PRECAUTIONS
• Be sure to shut off all phases of the external power supply used by the system
before wiring. Failure to do so may result in an electric shock, product damage or
malfunctions.
• Please make sure to ground FG terminal of the GOT power supply section by
applying 100 or less which is used exclusively for the GOT. Not doing so may
cause an electric shock or malfunction.
• Correctly wire the GOT power supply section after confirming the rated voltage
and terminal arrangement of the product. Not doing so can cause a fire or failure.
• Tighten the terminal screws of the GOT power supply section in the specified
torque range. Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the
screws or the GOT.
• Exercise care to avoid foreign matter such as chips and wire offcuts entering the
GOT. Not doing so can cause a fire, failure or malfunction.
Before using this product, please read this manual and the relevant manuals introduced
in this manual carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "DANGER" and "CAUTION".
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
• Before performing the test operations of the user creation monitor screen (such as
turning ON or OFF bit device, changing the word device current value, changing
the settings or current values of the timer or counter), read through the manual
carefully and make yourself familiar with the operation method.
During test operation, never change the data of the devices which are used to
perform significant operation for the system. False output or malfunction can
cause an accident.
• When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
• Connect the battery correctly.
Do not discharge, disassemble, heat, short, solder or throw the battery into the fire.
Incorrect handling may cause the battery to generate heat, burst or take fire,
resulting in injuries or fires.
• Before starting cleaning or terminal screw retightening, always switch off the
power externally in all phases. Not switching the power off in all phases can cause
a unit failure or malfunction. Undertightening can cause a short circuit or
malfunction. Overtightening can cause a short circuit or malfunction due to the
damage of the screws or unit.
• Be sure to shut off all phases of the external power supply used by the
system before mounting or removing the GOT to/from the panel.
Not doing so can cause the unit to fail or malfunction.
• When installing the battery wear an earth band etc. to avoid the static electricity.
The static electricity can cause the unit to fail or malfunction.
STARTUP/MAINTENANCE
PRECAUTIONS
• Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
• Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
• The cables connected to the unit must be run in ducts or clamped.
Not doing so can cause the unit or cable to be damaged due to the dangling,
motion or accidental pulling of the cables or can cause a malfunction due to a
cable connection fault.
• When unplugging the cable connected to the unit, do not hold and pull the cable
portion. Doing so can cause the unit or cable to be damaged or can cause a
malfunction due to a cable connection fault.
• Do not drop or apply any impact to the battery.
If any impact has been applied, discard the battery and never use it.
The battery may be damaged by the drop or impact.
• Before touching the unit, always touch grounded metal, etc. to discharge static
electricity from human body, etc.
Not doing so can cause the unit to fail malfunction.
DISPOSAL PRECAUTIONS
• When disposing of the product, handle it as industrial waste.
Specifications
Item
GT1030-LBD/LBD2/LBDW/LBDW2
0 to 50°C
Other than display section
Storage ambient temperature
0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)
-20 to 60°C
Operating ambient humidity
10 to 90% RH, non-condensing (The wet bulb temperature is 39°C or less.)
Storage ambient humidity
10 to 90% RH, non-condensing (The wet bulb temperature is 39°C or less.)
Frequency
Conforms to JIS
B3502 and
IEC61131-2
Vibration resistance
Shock resistance
Operating altitude
EN61131-2 : 2003
Programmable controllers- Equipment, requirement
and tests
Under intermittent
vibration
Under continuous
vibration
Acceleration
Half-amplitude
5 to 9Hz
--
3.5mm
9 to 150Hz
9.8m/s2
--
5 to 9Hz
--
1.75mm
9 to 150Hz
4.9m/s2
--
Sweep Count
EMS
Compliance with all relevant aspects of the standard.
(ESD,RF electromagnetic field, EFTB, Surge, RF conducted disturbances and Power frequency magnetic field)
Existing Cables
GT1030-LBD, GT1030-LBDW
GT10-C30R4-8P (For Melsec FX series PLC)
GT1030-LBD2, GT1030-LBDW2
GT10-C30R2-6P (For Melsec Q series PLC)
2) General notes on the use of the power cable
The GT1030-LBD/LBD2/LBDW/LBDW2 unit demand that the cable for the power supply is 10m or less.
Associated Manuals
Contents
Manual Number
(Model Code)
GT10 User's Manual
(sold separately)
Describes the GT10 hardware-relevant content such as part names, external dimensions,
mounting, power supply wiring, specifications, and introduction to option devices
JY997D24701
(09R819)
GOT1000 Series Connection Manual 1/3, 2/3, 3/3
(sold separately) *1
Describes system configurations of the connection method applicable to GOT1000 series
and cable creation method
SH-080532ENG
(1D7M26)
GT Designer2 Version2 Basic Operation/Data Transfer
Describes methods of the GT Designer2 installation operation, basic operation for drawing
Manual (For GOT1000 Series)
and transmitting data to GOT1000 series
(sold separately) *1
SH-080529ENG
(1D7M24)
GT Designer2 Version2 Screen Design Manual
(For GOT1000 Series) 1/3, 2/3, 3/3
(sold separately) *1
SH-080530ENG
SH-080531ENG
(1D7M25)
Describes specifications and settings of the object functions used in GT Designer2
*1 Stored in the GT Works 2/GT Designer2 in PDF format.
For details of a PLC to be connected, refer to the PLC user's manual respectively.
Bundled Items
Model Name
Explanation of the GOT model name
Remark
GT10 2 0 -
GT1030-LBD
GT1030-LBD2
GT1030-LBDW
GT1030-LBDW2
Maintenance Supplies
Quantity
PLC Communication Connector
1
Panel Mounting Bracket (with M4 × 20 screws)
4
Panel Mounting Packing
1
GT10 General Description (This manual)
1
2:RS-232
Interface type for
communication with PLC Blank:RS-422
Backlight type
W:white/red/pink
Blank:green/red/orange
Power type
D:24VDC
L:5VDC
B:Black
Panel color type
Display device type L:STN monochrome
0:Monochrome(black/white)
Display color type
Screen size type
3:4.5"
2:3.7"
GOT1000 series
GT10
*2 For the details of system information, refer to the following.
GT Designer2 Version† Screen Designer Manual
*3 ROM in which new data can be written without deleting the written data.
*4 Note that this does not guarantee all users' operation environment.
1.3 Communication Specifications
Specifications
Item
2000 m (6562 ft) max.
* * * * *
GOT main unit
(The maintenance supplies below are packed with the product.)
10 times each in X,
Y and Z directions
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electroconductive dust particles and
must be no direct sunlight. (Same as for saving)
*1
Compliance with all relevant aspects of the standard.
(Radiated Emissions)
1) General notes on the use of communication cables
Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise. Therefore, when installing any communication cables care
should always be taken with the routing and location of those cables. The GOT units identified on the previous chapter are compliant with the EMC requirement when the
following communication cables are used.
GT1030-LBD/LBDW
Communication standard
PLC communication
Conforms to JIS B3502, IEC 61131-2 (147m/s2, 11 ms, Sine half-wave pulse, 3 times each in the X, Y, and Z directions.)
Operating atmosphere
Remark
EMI
*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal
display panel. It is impossible to completely avoid this symptom, as the liquid
crystal display comprises of a great number of display elements. Flickers may
be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not
caused by product defect.
When the same screen is displayed for a long time, an incidental color or
partial discoloration is generated on the screen due to heat damage, and it
may not disappear.
To prevent heat damage, the screen saver function is effective.
For details of the screen saver function, refer to the following.
GT10 User's Manual
1.1 General Specifications
Display section
Standard
Manual name
1. Specifications
Operating ambient
temperature
The following products have shown compliance through direct testing (to the identified standards) and design analysis (forming a technical construction file) to the European
Directive for Electromagnetic Compatibility (89/336/EEC) when used as directed by the appropriate documentation.
Type :Programmable Controller (Open Type Equipment)
The following manuals are relevant to this product. When these loose manuals are required, please consult with our local distributor.
• Some failures of the GOT or cable may keep the outputs on or off.
An external monitoring circuit should be provided to check for output signals
which may lead to a serious accident.
Not doing so can cause an accident due to false output or malfunction.
• If a communication fault (including cable disconnection) occurs during
monitoring on the GOT, communication between the GOT and PLC CPU is
suspended and the GOT becomes inoperative.
A system where the GOT is used should be configured to perform any
significant operation to the system by using the switches of a device other
than the GOT on the assumption that a GOT communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
• Do not use the GOT as the warning device that may cause a serious accident.
An independent and redundant hardware or mechanical interlock is required to
configure the device that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect
output or malfunction.
• Incorrect operation of the touch switch(s) may lead to a serious accident if the
GOT backlight is gone out.
When the GOT backlight goes out, causes the monitor screen to appear
blank, while the input of the touch switch(s) remains active.
This may confuse an operator in thinking that the GOT is in "screensaver"
mode, who then tries to release the GOT from this mode by touching the
display section, which may cause a touch switch to operate.
MOUNTING
PRECAUTIONS
Requirement for Compliance with EMC directive
GOT Unit
TEST OPERATION
PRECAUTIONS
STARTUP/MAINTENANCE
PRECAUTIONS
• Do not bundle the control and communication cables with main-circuit, power
or other wiring.
Run the above cables separately from such wiring and keep them a minimum
of 100mm (3.94in.) apart.Not doing so noise can cause a malfunction.
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive for the entire mechanical module should be checked by
the user / manufacturer. For more details please contact the local Mitsubishi Electric
sales site.
Notes for compliance to EMC regulation
• Plug the communication cable into the connector of the connected unit and
tighten the mounting and terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction. Overtightening can
cause a short circuit or malfunction due to the damage of the screws or unit.
DESIGN PRECAUTIONS
DESIGN PRECAUTIONS
• Before transporting the GOT, turn the GOT power on and check that the battery
voltage status is normal on the Time setting & display screen (utilities screen). In
addition, confirm that the adequate battery life remains on the rating plate.
Transporting the GOT with the low battery voltage or the battery the reached
battery life may unstabilize the backup data unstable during transportation.
• Make sure to transport the GOT main unit and/or relevant unit(s) in the manner
they will not be exposed to the impact exceeding the impact resistance
described in the general specifications of this manual, as they are precision
devices. Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
For more details please contact the local Mitsubishi Electric sales site.
WIRING PRECAUTIONS
Safety Precaution (Read these precautions before using.)
Compliance with EC directive (CE Marking)
TRANSPORTATION
PRECAUTIONS
MOUNTING PRECAUTIONS
PC communication*1
GT1030-LBD2/LBDW2
RS-422 1ch
RS-232 1ch
Transmission speed
115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
Connector terminal block 9-pins
Communication standard
RS-232 1ch
Transmission speed
115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
MINI DIN 6-pins (Female)
Installation location
Inside control panel
Overvoltage category*2
II or less
Pollution degree*3
2 or less
1.4 Power Supply Specifications
Cooling method
Self-cooling
(For details on power supply wiring, such as the allowable cable size and tightening torque, refer to the additional manual, "GT10 User's Manual".)
*1 Project data upload/download, OS installation, Transparent function
*1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
*2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
1.2 Performance Specifications
Specifications
Item
Display
section*1
24VDC (+10% -15%), ripple voltage 200mV or less
Fuse (built-in, not exchangeable)
0.5A
Power consumption, (At backlight off)
2.2W (90mA/24VDC) or less, (1.7W (70mA/24VDC) or less)
Inrush current
18A or less (26.4VDC) 1ms
Permissible instantaneous power failure
Within 5ms
time*1
STN monochrome (white/black) liquid crystal
Noise immunity
Noise voltage: 1000Vp-p, Noise width: 1µs (by noise simulator of 30 to 100Hz noise frequency)
4.5"
Dielectric withstand voltage
500VAC for 1 minute (between the GOT’s power supply terminals and the GOT’s grounding terminal)
Resolution
288 × 96 dots (Horizontal format)
Insulation resistance
10MΩ or larger by insulation resistance tester (between the GOT’s power supply terminals and the GOT’s grounding terminal)
Display size
W109.42(4.3) × H35.98(1.41) [mm](inch) (Horizontal format)
Grounding
Class D grounding (100Ω or less). To be connected to the panel when grounding is not possible
Display character
16-dot standard font: 36 characters × 6 lines, 12-dot standard font: 48 characters × 8 lines (Horizontal format)
Display color
Monochrome (white/black)
Display angle
Left/Right: 30 degrees, Top: 20 degrees, Bottom: 30 degrees (Horizontal format)
Contrast adjustment
16-level adjustment
Intensity of LCD only
200 [cd/m2] (in green)
Intensity adjustment
8-level adjustment
300 [cd/m2] (in white)
Approx. 50,000h. (Time for display intensity to become 1/5 at operating ambient temperature of 25°C)
LED with 3 available colors (green, red, orange)
*1 The GOT continues to operate even upon 5ms or shorter instantaneous power failure.
The GOT stops operating if there is extended power failure or voltage drop, while it automatically resumes operation as soon as the power is restored.
2. Wiring of connection cable
The diagram below shows cable assignment for GOT port.
Cables: GT10-C†††R4-8P, GT10-C†††R4-2P, GT10-C†††R2-6P
GOT
PLC
LED with 3 available colors (white, red, pink)
PLC connection cable
This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Backlight status (colors, ON/BLINK/OFF) control, Adjustable screensaver activation time
Setting the system information enables*2 PLC to control the backlight status
Number of touch keys
Maximum 50 keys/screen (Matrix resistive film touch panel)
Key size
Minimum 16 × 16 dots (per key)
Simultaneous pressing of
two (or more) areas
Enable
(2-point press)
Life
1 million times or more (operating force 0.98N max.)
User memory*3
Flash memory ROM (Internal), for storing Project data (1.5M bytes or less), OS
Life
(Number of write times)
100,000 times
GT11-50BAT lithium battery
Battery
Input power supply voltage
Screen size
Life
Memory
GT1030-LBDW/LBDW2
GT1030-LBD/LBD2/LBDW/LBDW2
Type
Backlight
(no replacement required)
Touch
panel
GT1030-LBD/LBD2
Specifications
Item
Backup target
Clock data, alarm history and recipe data
Life
Approx. 5 years (Operating ambient temperature of 25 )
Buzzer output
(a buzzer that sounds when touch Single tone (LONG/ SHORT/ OFF adjustable)
keys are pressed)
Environmental protective structure*4
Equivalent to IP67 (JEM1030) (front section)
External dimensions
W145(5.7) × H76(2.99) × D29.5(1.16)[mm](inch) (Excluding mounting fixtures) (Horizontal format)
Panel cutting dimensions
W137 (5.39) × H66 (2.59) [mm] (inch) (Horizontal format)
Weight
0.3kg (Excluding mounting fixtures)
Compatible software package
GT Designer2 Version2.58L or later
GT10-C
R4-8P
GOT
(terminal
block)
SDA
SDB
RDA
RDB
SG
RSA
RSB
CSA
CSB
GT10-C
Untied
wire
color
GOT
(terminal
block)
Brown
Red
Orange
Yellow
Green
Black
White
SDA
SDB
RDA
RDB
SG
RSA
RSB
CSA
CSB
GT10-C
R4-25P
Untied
wire
color
R2-6P
GOT
(terminal
block)
Brown
Red
Orange
Yellow
Green
Blue
Purple
Black
White
SD
RD
ER
DR
SG
RS
CS
NC
NC
Untied
wire
color
Brown
Red
Blue
Yellow
Green
Purple
User-made cable is necessary, depending on the PLC.
For the detail, refer to GOT1000 Series Connection Manual.
Cable jacket to remove
7mm (0.27")
Tightening torque
0.22 to 0.25 N•m
Recommended Tool
(Screwdriver)
SZS 0.4 × 2.5
(Phoenix Contact Inc.)
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For safe use
• This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
• This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310,
JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN
JY997D25301F
Side
B
Side
Side
A
B
JAPANESE
ENGLISH
GT1030-LBD†, GT1030-LBD†2
GT10 General Description
Manual Number
JY997D25301F
Date
Sep 2008
This manual describes the specifications of the product. Before use, read this
manual and manuals of relevant products fully to acquire proficiency in handling
and operating the product. Make sure to learn all the product information, safety
information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are
the registered trademarks or trademarks of each company.
Effective Sep 2008
Specifications are subject to change without notice.
© 2008 Mitsubishi Electric Corporation
• Use the GOT in the environment that satisfies the general specifications
described in this manual. Not doing so can cause an electric shock, fire,
malfunction or product damage or deterioration.
• When mounting the GOT to the control panel, tighten the mounting screws in the
specified torque range. Undertightening can cause the GOT to drop, short circuit
or malfunction. Overtightening can cause a drop, short circuit or malfunction due
to the damage of the screws or the GOT.
WIRING PRECAUTIONS
• Be sure to shut off all phases of the external power supply used by the system
before wiring. Failure to do so may result in an electric shock, product damage or
malfunctions.
• Please make sure to ground FG terminal of the GOT power supply section by
applying 100 or less which is used exclusively for the GOT. Not doing so may
cause an electric shock or malfunction.
• Correctly wire the GOT power supply section after confirming the rated voltage
and terminal arrangement of the product. Not doing so can cause a fire or failure.
• Tighten the terminal screws of the GOT power supply section in the specified
torque range. Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the
screws or the GOT.
• Exercise care to avoid foreign matter such as chips and wire offcuts entering the
GOT. Not doing so can cause a fire, failure or malfunction.
Before using this product, please read this manual and the relevant manuals introduced
in this manual carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "DANGER" and "CAUTION".
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
• Before performing the test operations of the user creation monitor screen (such as
turning ON or OFF bit device, changing the word device current value, changing
the settings or current values of the timer or counter), read through the manual
carefully and make yourself familiar with the operation method.
During test operation, never change the data of the devices which are used to
perform significant operation for the system. False output or malfunction can
cause an accident.
• When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
• Connect the battery correctly.
Do not discharge, disassemble, heat, short, solder or throw the battery into the fire.
Incorrect handling may cause the battery to generate heat, burst or take fire,
resulting in injuries or fires.
• Before starting cleaning or terminal screw retightening, always switch off the
power externally in all phases. Not switching the power off in all phases can cause
a unit failure or malfunction. Undertightening can cause a short circuit or
malfunction. Overtightening can cause a short circuit or malfunction due to the
damage of the screws or unit.
• Be sure to shut off all phases of the external power supply used by the
system before mounting or removing the GOT to/from the panel.
Not doing so can cause the unit to fail or malfunction.
• When installing the battery wear an earth band etc. to avoid the static electricity.
The static electricity can cause the unit to fail or malfunction.
STARTUP/MAINTENANCE
PRECAUTIONS
• Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
• Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
• The cables connected to the unit must be run in ducts or clamped.
Not doing so can cause the unit or cable to be damaged due to the dangling,
motion or accidental pulling of the cables or can cause a malfunction due to a
cable connection fault.
• When unplugging the cable connected to the unit, do not hold and pull the cable
portion. Doing so can cause the unit or cable to be damaged or can cause a
malfunction due to a cable connection fault.
• Do not drop or apply any impact to the battery.
If any impact has been applied, discard the battery and never use it.
The battery may be damaged by the drop or impact.
• Before touching the unit, always touch grounded metal, etc. to discharge static
electricity from human body, etc.
Not doing so can cause the unit to fail malfunction.
DISPOSAL PRECAUTIONS
• When disposing of the product, handle it as industrial waste.
Specifications
Item
GT1030-LBD/LBD2/LBDW/LBDW2
0 to 50°C
Other than display section
Storage ambient temperature
0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)
-20 to 60°C
Operating ambient humidity
10 to 90% RH, non-condensing (The wet bulb temperature is 39°C or less.)
Storage ambient humidity
10 to 90% RH, non-condensing (The wet bulb temperature is 39°C or less.)
Frequency
Conforms to JIS
B3502 and
IEC61131-2
Vibration resistance
Shock resistance
Operating altitude
EN61131-2 : 2003
Programmable controllers- Equipment, requirement
and tests
Under intermittent
vibration
Under continuous
vibration
Acceleration
Half-amplitude
5 to 9Hz
--
3.5mm
9 to 150Hz
9.8m/s2
--
5 to 9Hz
--
1.75mm
9 to 150Hz
4.9m/s2
--
Sweep Count
EMS
Compliance with all relevant aspects of the standard.
(ESD,RF electromagnetic field, EFTB, Surge, RF conducted disturbances and Power frequency magnetic field)
Existing Cables
GT1030-LBD, GT1030-LBDW
GT10-C30R4-8P (For Melsec FX series PLC)
GT1030-LBD2, GT1030-LBDW2
GT10-C30R2-6P (For Melsec Q series PLC)
2) General notes on the use of the power cable
The GT1030-LBD/LBD2/LBDW/LBDW2 unit demand that the cable for the power supply is 10m or less.
Associated Manuals
Contents
Manual Number
(Model Code)
GT10 User's Manual
(sold separately)
Describes the GT10 hardware-relevant content such as part names, external dimensions,
mounting, power supply wiring, specifications, and introduction to option devices
JY997D24701
(09R819)
GOT1000 Series Connection Manual 1/3, 2/3, 3/3
(sold separately) *1
Describes system configurations of the connection method applicable to GOT1000 series
and cable creation method
SH-080532ENG
(1D7M26)
GT Designer2 Version2 Basic Operation/Data Transfer
Describes methods of the GT Designer2 installation operation, basic operation for drawing
Manual (For GOT1000 Series)
and transmitting data to GOT1000 series
(sold separately) *1
SH-080529ENG
(1D7M24)
GT Designer2 Version2 Screen Design Manual
(For GOT1000 Series) 1/3, 2/3, 3/3
(sold separately) *1
SH-080530ENG
SH-080531ENG
(1D7M25)
Describes specifications and settings of the object functions used in GT Designer2
*1 Stored in the GT Works 2/GT Designer2 in PDF format.
For details of a PLC to be connected, refer to the PLC user's manual respectively.
Bundled Items
Model Name
Explanation of the GOT model name
Remark
GT10 2 0 -
GT1030-LBD
GT1030-LBD2
GT1030-LBDW
GT1030-LBDW2
Maintenance Supplies
Quantity
PLC Communication Connector
1
Panel Mounting Bracket (with M4 × 20 screws)
4
Panel Mounting Packing
1
GT10 General Description (This manual)
1
2:RS-232
Interface type for
communication with PLC Blank:RS-422
Backlight type
W:white/red/pink
Blank:green/red/orange
Power type
D:24VDC
L:5VDC
B:Black
Panel color type
Display device type L:STN monochrome
0:Monochrome(black/white)
Display color type
Screen size type
3:4.5"
2:3.7"
GOT1000 series
GT10
*2 For the details of system information, refer to the following.
GT Designer2 Version† Screen Designer Manual
*3 ROM in which new data can be written without deleting the written data.
*4 Note that this does not guarantee all users' operation environment.
1.3 Communication Specifications
Specifications
Item
2000 m (6562 ft) max.
* * * * *
GOT main unit
(The maintenance supplies below are packed with the product.)
10 times each in X,
Y and Z directions
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electroconductive dust particles and
must be no direct sunlight. (Same as for saving)
*1
Compliance with all relevant aspects of the standard.
(Radiated Emissions)
1) General notes on the use of communication cables
Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise. Therefore, when installing any communication cables care
should always be taken with the routing and location of those cables. The GOT units identified on the previous chapter are compliant with the EMC requirement when the
following communication cables are used.
GT1030-LBD/LBDW
Communication standard
PLC communication
Conforms to JIS B3502, IEC 61131-2 (147m/s2, 11 ms, Sine half-wave pulse, 3 times each in the X, Y, and Z directions.)
Operating atmosphere
Remark
EMI
*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal
display panel. It is impossible to completely avoid this symptom, as the liquid
crystal display comprises of a great number of display elements. Flickers may
be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not
caused by product defect.
When the same screen is displayed for a long time, an incidental color or
partial discoloration is generated on the screen due to heat damage, and it
may not disappear.
To prevent heat damage, the screen saver function is effective.
For details of the screen saver function, refer to the following.
GT10 User's Manual
1.1 General Specifications
Display section
Standard
Manual name
1. Specifications
Operating ambient
temperature
The following products have shown compliance through direct testing (to the identified standards) and design analysis (forming a technical construction file) to the European
Directive for Electromagnetic Compatibility (89/336/EEC) when used as directed by the appropriate documentation.
Type :Programmable Controller (Open Type Equipment)
The following manuals are relevant to this product. When these loose manuals are required, please consult with our local distributor.
• Some failures of the GOT or cable may keep the outputs on or off.
An external monitoring circuit should be provided to check for output signals
which may lead to a serious accident.
Not doing so can cause an accident due to false output or malfunction.
• If a communication fault (including cable disconnection) occurs during
monitoring on the GOT, communication between the GOT and PLC CPU is
suspended and the GOT becomes inoperative.
A system where the GOT is used should be configured to perform any
significant operation to the system by using the switches of a device other
than the GOT on the assumption that a GOT communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
• Do not use the GOT as the warning device that may cause a serious accident.
An independent and redundant hardware or mechanical interlock is required to
configure the device that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect
output or malfunction.
• Incorrect operation of the touch switch(s) may lead to a serious accident if the
GOT backlight is gone out.
When the GOT backlight goes out, causes the monitor screen to appear
blank, while the input of the touch switch(s) remains active.
This may confuse an operator in thinking that the GOT is in "screensaver"
mode, who then tries to release the GOT from this mode by touching the
display section, which may cause a touch switch to operate.
MOUNTING
PRECAUTIONS
Requirement for Compliance with EMC directive
GOT Unit
TEST OPERATION
PRECAUTIONS
STARTUP/MAINTENANCE
PRECAUTIONS
• Do not bundle the control and communication cables with main-circuit, power
or other wiring.
Run the above cables separately from such wiring and keep them a minimum
of 100mm (3.94in.) apart.Not doing so noise can cause a malfunction.
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive for the entire mechanical module should be checked by
the user / manufacturer. For more details please contact the local Mitsubishi Electric
sales site.
Notes for compliance to EMC regulation
• Plug the communication cable into the connector of the connected unit and
tighten the mounting and terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction. Overtightening can
cause a short circuit or malfunction due to the damage of the screws or unit.
DESIGN PRECAUTIONS
DESIGN PRECAUTIONS
• Before transporting the GOT, turn the GOT power on and check that the battery
voltage status is normal on the Time setting & display screen (utilities screen). In
addition, confirm that the adequate battery life remains on the rating plate.
Transporting the GOT with the low battery voltage or the battery the reached
battery life may unstabilize the backup data unstable during transportation.
• Make sure to transport the GOT main unit and/or relevant unit(s) in the manner
they will not be exposed to the impact exceeding the impact resistance
described in the general specifications of this manual, as they are precision
devices. Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
For more details please contact the local Mitsubishi Electric sales site.
WIRING PRECAUTIONS
Safety Precaution (Read these precautions before using.)
Compliance with EC directive (CE Marking)
TRANSPORTATION
PRECAUTIONS
MOUNTING PRECAUTIONS
PC communication*1
GT1030-LBD2/LBDW2
RS-422 1ch
RS-232 1ch
Transmission speed
115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
Connector terminal block 9-pins
Communication standard
RS-232 1ch
Transmission speed
115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
MINI DIN 6-pins (Female)
Installation location
Inside control panel
Overvoltage category*2
II or less
Pollution degree*3
2 or less
1.4 Power Supply Specifications
Cooling method
Self-cooling
(For details on power supply wiring, such as the allowable cable size and tightening torque, refer to the additional manual, "GT10 User's Manual".)
*1 Project data upload/download, OS installation, Transparent function
*1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
*2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
1.2 Performance Specifications
Specifications
Item
Display
section*1
24VDC (+10% -15%), ripple voltage 200mV or less
Fuse (built-in, not exchangeable)
0.5A
Power consumption, (At backlight off)
2.2W (90mA/24VDC) or less, (1.7W (70mA/24VDC) or less)
Inrush current
18A or less (26.4VDC) 1ms
Permissible instantaneous power failure
Within 5ms
time*1
STN monochrome (white/black) liquid crystal
Noise immunity
Noise voltage: 1000Vp-p, Noise width: 1µs (by noise simulator of 30 to 100Hz noise frequency)
4.5"
Dielectric withstand voltage
500VAC for 1 minute (between the GOT’s power supply terminals and the GOT’s grounding terminal)
Resolution
288 × 96 dots (Horizontal format)
Insulation resistance
10MΩ or larger by insulation resistance tester (between the GOT’s power supply terminals and the GOT’s grounding terminal)
Display size
W109.42(4.3) × H35.98(1.41) [mm](inch) (Horizontal format)
Grounding
Class D grounding (100Ω or less). To be connected to the panel when grounding is not possible
Display character
16-dot standard font: 36 characters × 6 lines, 12-dot standard font: 48 characters × 8 lines (Horizontal format)
Display color
Monochrome (white/black)
Display angle
Left/Right: 30 degrees, Top: 20 degrees, Bottom: 30 degrees (Horizontal format)
Contrast adjustment
16-level adjustment
Intensity of LCD only
200 [cd/m2] (in green)
Intensity adjustment
8-level adjustment
300 [cd/m2] (in white)
Approx. 50,000h. (Time for display intensity to become 1/5 at operating ambient temperature of 25°C)
LED with 3 available colors (green, red, orange)
*1 The GOT continues to operate even upon 5ms or shorter instantaneous power failure.
The GOT stops operating if there is extended power failure or voltage drop, while it automatically resumes operation as soon as the power is restored.
2. Wiring of connection cable
The diagram below shows cable assignment for GOT port.
Cables: GT10-C†††R4-8P, GT10-C†††R4-2P, GT10-C†††R2-6P
GOT
PLC
LED with 3 available colors (white, red, pink)
PLC connection cable
This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Backlight status (colors, ON/BLINK/OFF) control, Adjustable screensaver activation time
Setting the system information enables*2 PLC to control the backlight status
Number of touch keys
Maximum 50 keys/screen (Matrix resistive film touch panel)
Key size
Minimum 16 × 16 dots (per key)
Simultaneous pressing of
two (or more) areas
Enable
(2-point press)
Life
1 million times or more (operating force 0.98N max.)
User memory*3
Flash memory ROM (Internal), for storing Project data (1.5M bytes or less), OS
Life
(Number of write times)
100,000 times
GT11-50BAT lithium battery
Battery
Input power supply voltage
Screen size
Life
Memory
GT1030-LBDW/LBDW2
GT1030-LBD/LBD2/LBDW/LBDW2
Type
Backlight
(no replacement required)
Touch
panel
GT1030-LBD/LBD2
Specifications
Item
Backup target
Clock data, alarm history and recipe data
Life
Approx. 5 years (Operating ambient temperature of 25 )
Buzzer output
(a buzzer that sounds when touch Single tone (LONG/ SHORT/ OFF adjustable)
keys are pressed)
Environmental protective structure*4
Equivalent to IP67 (JEM1030) (front section)
External dimensions
W145(5.7) × H76(2.99) × D29.5(1.16)[mm](inch) (Excluding mounting fixtures) (Horizontal format)
Panel cutting dimensions
W137 (5.39) × H66 (2.59) [mm] (inch) (Horizontal format)
Weight
0.3kg (Excluding mounting fixtures)
Compatible software package
GT Designer2 Version2.58L or later
GT10-C
R4-8P
GOT
(terminal
block)
SDA
SDB
RDA
RDB
SG
RSA
RSB
CSA
CSB
GT10-C
Untied
wire
color
GOT
(terminal
block)
Brown
Red
Orange
Yellow
Green
Black
White
SDA
SDB
RDA
RDB
SG
RSA
RSB
CSA
CSB
GT10-C
R4-25P
Untied
wire
color
R2-6P
GOT
(terminal
block)
Brown
Red
Orange
Yellow
Green
Blue
Purple
Black
White
SD
RD
ER
DR
SG
RS
CS
NC
NC
Untied
wire
color
Brown
Red
Blue
Yellow
Green
Purple
User-made cable is necessary, depending on the PLC.
For the detail, refer to GOT1000 Series Connection Manual.
Cable jacket to remove
7mm (0.27")
Tightening torque
0.22 to 0.25 N•m
Recommended Tool
(Screwdriver)
SZS 0.4 × 2.5
(Phoenix Contact Inc.)
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For safe use
• This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
• This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310,
JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN