Mitsubishi Electric PQHY-P400-500YSGM-A Installation manual

Air-Conditioners For Building Application
HEAT SOURCE UNIT
PQHY-P400·500YSGM-A
INSTALLATION
MANUAL
For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit.
I
E
F
D
GB
For use with R410A
MANUEL D’INSTALLATION
NL
INSTALLATIONSHANDBUCH
Zum sicheren und ordnungsgemäßen Gebrauch der Klimageräte das Installationshandbuch gründlich durchlesen.
MANUAL
DE INSTALACIÓN
Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de aire acondicionado.
P
Veuillez lire le manuel d’installation en entier avant d’installer ce climatiseur pour éviter tout accident et vous assurer d’une utilisation correcte.
MANUAL DE INSTALAÇÃO
Para segurança e utilização correctas, leia atentamente este manual de instalação antes de instalar a unidade de ar condicionado.
RU
INSTALLATIEHANDLEIDING
Voor een veilig en juist gebruik moet u deze installatiehandleiding grondig doorlezen voordat u de airconditioner installeert.
GR
MANUALE DI INSTALLAZIONE
Per un uso sicuro e corretto, leggere attentamente questo manuale di installazione prima di installare il condizionatore d’aria.
РУКОВОДСТВО ПО УСТАНОВКЕ
Для осторожного и правильного использования прибора необходимо тщательно ознакомиться с данным руководством по
установке до выполнения установки кондиционера.
MONTAJ ELK‹TABI
Emniyetli ve do¤ru biçimde nas›l kullan›laca¤›n› ö¤renmek için lütfen klima cihaz›n› monte etmeden önce bu elkitab›n› dikkatle okuyunuz.
TR
E°XEIPI¢IO O¢H°IøN E°KATA™TA™H™
°È· ·ÛÊ¿ÏÂÈ· Î·È ÛˆÛÙ‹ ¯Ú‹ÛË, ·Ú·Î·Ï›ÛÙ ‰È·‚¿ÛÂÙ ÚÔÛ¯ÙÈο ·˘Ùfi ÙÔ ÂÁ¯ÂÈÚ›‰ÈÔ ÂÁηٿÛÙ·Û˘ ÚÈÓ ·Ú¯›ÛÂÙ ÙËÓ
ÂÁηٿÛÙ·ÛË Ù˘ ÌÔÓ¿‰·˜ ÎÏÈÌ·ÙÈÛÌÔ‡.
5
6.2
[Fig. 5.0.1]
[Fig. 6.2.1]
<
= 40°
<A>
>8m
=
(10) *1
550
>8m
=
B
C
600
A
D
400
990
990
E
6
6.1
400
990
<B>
D
<A>
45 45
900
45
C
D
990
<B>
900
(1254)
602
D
602
550
45
45
602
570
550
900
990
16
C
D
<A> Side-by-side installation
<B> Back-to-back installation
Heat exchanger unit
B
Compressor unit
C
4-ø14 (Anchoring hole)
D
(Top view)
*1
Select an installation site that is level and free from vibrations so that the side
panels of the units do not rub against each other.
Select an installation site that allows the fixation of the units to the floor.
[Fig. 6.1.2]
2
A
Piping space (for side piping)
B
Heat exchanger unit
C
Compressor unit
D
Service space (front side)
E
(Top view)
F
Piping space
*2
F
400
<A> Side-by-side installation
<B> Back-to-back installation
*1
A
E
990
E
(1254)
(50) *2
570
400
B
A
C
45
A
B
C
16
45
570
B
F
16
A
550
(50) *2
C
550
990
900
550
990
1990
(10) *1
400
45
*2
600
[Fig. 6.1.1]
E
Anti-vibration pad etc.
F
Concrete base
Select an installation site that is level and free from vibrations so that the side
panels of the units do not rub against each other.
Select an installation site that allows the fixation of the units to the floor.
6.2
[Fig. 6.2.2]
<A>
<A> Side-by-side installation
<B> Sample back-to-back installation
400
G
Piping space (for top piping)
H
Piping space (for side piping)
I
Heat exchanger unit
J
Compressor unit
K
Field-installed pipes
Bypass pipe
ø9.52 (Flare + Brazed)
High press pipe ø19.05 (Flare + Brazed)
Low press pipe ø25.4 (Flange + Brazed)
Connecting wire between heat exchanger unit and compressor unit (External
heater adapter*)
Control signal wire (connector, on-site connection)
* If the space between the heat exchanger unit and compressor unit exceeds 1.5 m
(the length of the standard supplied external heater adapter), an optional external
heater adapter (available in 5m or10m) is necessary.
L
990
G
I
J
H
M
(Front view)
N
Service space (Heat exchanger unit side)
O
Service space (Compressor unit side)
P
Piping space
Q
Pipe/wire output port
R
(Side view)
*1
Select an installation site that is level and free from vibrations so that the side panels of
the units do not rub against each other.
Select an installation site that allows the fixation of the units to the floor.
BV5
BV3
BV4
K
<B>
L*
M
400
(1254)
990
400
*2
(10) *1
990
G
I
400
G
J
J
P
N
H
O
BV5
BV3
BV4
600
602
602
600
(50) *2
L
Q
R
7
M
7.1
7.4
[Fig. 7.1.1]
[Fig. 7.4.1]
Side piping
D
Top piping
E
B
A
G
A
E
D
C
C
B
F
TB8
F
G
4
J
I
63PW
3
A
B
J
I
H
H
H
H
A
Water circulation pipe
F
Y-type strainer
B
Close valve
G
Water inlet
C
Close valve
H
Drain pipe
D
Water outlet
I
Heat exchanger unit
E
Refrigerant piping
J
Compressor unit
A
Short-circuit wire (Connected before delivery
from manufacturer)
B
Pump interlock circuit connection
3
8
8.2
[Fig. 8.2.1]
A
A
E
E
A
A
B
B
a
C
b
C
C
1
2
e
D
c
C
3
B
d
C
a
4
C
b
C
C
1
2
5
A
c
d
e
C
C
C
3
4
5
D
A
Heat source unit
B
First branch
C
Indoor unit
D
Cap
(mm)
Å Heat source model
P400
P500
ı Liquid pipe
ø12.7
ø15.88
Ç Gas pipe
ø28.58
ø28.58
B, C, D
Ï Downstream unit model total
~ 200
201 ~ 400
401 ~ 650
Ó The 1st branch of P450 ~ P650
(mm)
Î Total capacity of indoor units
~ 140
141 ~ 200
201 ~ 300
301 ~ 400
401 ~ 650
ı Liquid pipe
ø9.52
ø9.52
ø9.52
ø12.7
ø15.88
Ç Gas pipe
ø15.88
ø19.05
ø22.2
ø28.58
ø28.58
a, b, c, d, e
Ì Branch kit model
CMY-Y102S-G
CMY-Y102L-G
CMY-Y202G
¬ 4-Branching header
(Downstream unit
model total <= 200)
CMY-Y104-G
Ô 8-Branching header
(Downstream unit
model total <= 400)
CMY-Y108-G
Ò High press pipe
ø19.05
˜ Low press pipe
ø28.58
10-Branching header
(Downstream unit
model total <= 650)
CMY-Y1010-G
(mm)
‰ Model number
20,25,32,40,50
63,71,80,100,125,140
200
250
ı Liquid pipe
ø6.35
ø9.52
ø9.52
ø9.52
Ç Gas pipe
ø12.7
ø15.88
ø19.05
ø22.2
9
ˆ Bypass pipe
ø9.52
9.2
[Fig. 9.2.1]
[Fig. 9.2.2]
<A> [Ball valve (Low press. side/flanged type)]
<B> [Ball valve (High press. side/flared type)]
<C> This figure shows the valve
in the fully open state.
A
3
E
E
K
I
J
1
B
D
A
Close-packed packing
B
Hollow packing
H
A
Valve stem
B
Stopper pin
C
Packing (Accessory)
D
Connecting pipe (Accessory)
E
Open (Operate slowly)
F
Cap
G
Service port
H
ø12.7 (PQHY-P400)
ø15.88 (PQHY-P500)
* Connecting pipes are not provided
with the P500 models.
I
ø28.58 (PQHY-P400)
ø28.58 (PQHY-P500)
J
Field piping
C
G
F
O
S
S
A
B
I
H
C
4
D
G FE
O
[Fig. 9.2.3]
A
A
Heat exchanger unit
B
Compressor unit
C
Gas pipe
D
Liquid pipe
E
Heat exchanger unit – Compressor unit connection pipe (ø28.58 Flange + Brazed)
F
Heat exchanger unit – Compressor unit connection pipe (ø19.05 Flare + Brazed)
G
Heat exchanger unit – Compressor unit connection pipe (ø9.52 Flare + Brazed)
H
Ball valve
I
External heater adapter (3-wire)
B
[Fig. 9.2.4]
9.3
[Fig. 9.3.1]
[Fig. 9.3.2]
D
N
F
B
B
F
L
LO
A
O
HI
E
I
H
<A>
HI
D
G
C
B
H
I
C
LO
A
C
K
G
E
<B>
J
M
K
J
L
A
Nitrogen gas
G
Liquid pipe
B
To indoor unit
H
Gas pipe
A
System analyzer
J
Valve
B
Lo knob
K
C
System analyzer
I
R410A cylinder
Heat source unit
C
Hi knob
L
D
Lo knob
Scale
J
Service port
D
Ball valve (Heat exchanger unit side)
M
E
Vacuum pump
Hi knob
K
Heat exchanger unit
E
Liquid pipe
N
F
To indoor unit
Ball valve
L
Compressor unit
F
Gas pipe
O
Heat source unit
G
Service port
H
Three-way joint
I
Valve
<A> Open
<B> Closed
[Fig. 9.3.3]
A
B
A : Syphon pipe
In case of the cylinder having no syphon pipe.
9.4
[Fig. 9.4.1]
B
[Fig. 9.4.2]
A
[Fig. 9.4.3]
B
A
C
C
D
E
E
E
D
A
B
E
D
A
Steel wire
B
Piping
A
Liquid pipe
D
Finishing tape
C
Asphaltic oily mastic or asphalt
B
Gas pipe
E
Insulator
D
Heat insulation material A
C
Electric wire
E
Outer covering B
[Fig. 9.4.4]
<A> Inner wall (concealed)
AB
<B> Outer wall
C
<C> Outer wall (exposed)
<D> Floor (waterproofing)
D
D
A B
EB
F
<E> Roof pipe shaft
<F> Penetrating portion on fire
limit and boundary wall
I
G
J
D
B
I
A
Sleeve
G
Sleeve with edge
B
Heat insulating material
H
Lagging material
C
Lagging
I
Mortar or other incombustible caulking
D
Caulking material
J
Incombustible heat insulation material
E
Band
F
Waterproofing laye
G
B
H
F
A
1m
1m
5
10
10.2
[Fig. 10.2.1]
L1 L2 L3 N
TB1
M1M2
TB3
A
C
M1M2 S
TB7
A
Power source
B
Transmission line
C
Earth screw
B
[Fig. 10.2.2]
C
E
D
<A>
D
<B>
A
<C>
B
CN102B
CN103B
CN102A
CN103A
CN102B
<D>
CN103B
<E>
CN101B <J>
<F>
CN101B
C
<G>
CN101A
<I>
A
Heat exchanger unit
B
Compressor unit
C
Cable clamp (power supply line)
D
Cable clamp (control line)
E
Control cable
F
Power supply cable
<A>
<B>
<C>
<D>
<E>
<F>
<G>
<H>
<I>
<J>
<K>
CN101A
Enlarged view of connector section
Heat exchanger unit side
Compressor unit side
CN102B (For power supply line)
CN103B (For control line)
CN101B (For power supply line)
CN102A (For power supply line)
CN103A (For control line)
CN101A (For power supply line)
CN104B (For control line)
CN104A (For control line)
<A>
A
B
<A> Compressor unit
A
Cable clamp for power supply cable
B
Cable clamp for control cable
<H>
CN104A
<K>
F
[Fig. 10.2.3]
6
CN104B
CN103A
CN102A
CN104A
10.3
L1
[Fig. 10.3.1]
A
OC
<A> Change the jumper connector from CN41 to CN40
B
C
IC
IC
IC
IC
(01)
(04)
(05)
(06)
CN40
(51)
TB3
M1M2
TB5
M1M2 S
TB5
M1M2 S
TB5
M1M2 S
r1
M1M2 S
TB7
r2
<B> SW2-1:ON
TB5
M1M2 S
r3
L2
D
<C> Keep the jumper connector
on CN41
A B
A B
(105)
(155)
RC
RC
RC
L3
OC
<B> SW2-1:ON
A B
(101)
E
L4
IC
CN40
IC
IC
(52)
(03)
(02)
(07)
TB5
M1M2 S
TB5
M1M2 S
TB3
M1M2
TB5
M1M2 S
L5
M1M2 S
TB7
L6
System
controller
r4
M1M2S
A B
(103)
RC
[Fig. 10.3.2]
L1
A
OC
<A> Change the jumper connector from CN41 to CN40
CN40
B
C
IC
IC
IC
(01)
(04)
(05)
IC
(51)
TB3
M1M2
TB5
M1M2 S
TB15
1 2
TB5
M1M2 S
TB5
M1M2 S
TB15
1 2
c2
D
L2
<C> Keep the jumper connector
on CN41
c2
c1
c1
M1M2 S
TB7
A B
MA
<B> SW2-1:ON
A : Group 1
TB15
1 2
c4
A B
A B
MA
MA
E
L3
OC
TB5
M1M2 S
c3
<B> SW2-1:ON
(06)
c2
L4
IC
IC
IC
(02)
(03)
(07)
TB5 TB 15
M1M2 S 1 2
TB5 TB15
1 2
M1M2 S
CN40
(52)
B : Group 3
C : Group 5
TB5
M1M2 S
TB3
M1M2
M1M2 S
TB7
TB15
1 2
D : Shielded wire
c1
System
controller
L6
E : Sub remote
controller
M1M2 S
( ) Address
A B
MA
[Fig. 10.3.3]
L1
L2
L3
L5
OC
Ground
IC
IC
TB5
M1M2 S
RP
IC
TB2
TB3
A B S
A B S
TB5
M1M2 S
TB5
M1M2 S
IC
TB5
M1M2 S
r1
r1
L7
L4
TB3
M1M2
L6
A B
A B
RC
RC
N1
N2
10.4
[Fig. 10.4.1]
A : Switch (breakers for wiring and current leakage)
B : Breakers for current leakage
3N~380–415V
L1, L2, L3, N, PE
B
A
C
C : Heat source unit
D
D : Pull box
E : Indoor unit
~220–240V
L, N, PE
B
A
E
E
E
E
7
Contents
1. Safety precautions ...................................................................................... 8
1.1. Before installation and electric work .......................................... 8
1.2. Precautions for devices that use R410A refrigerant .................. 8
1.3. Before getting installed .............................................................. 9
1.4. Before installation electrical work .............................................. 9
1.5. Before starting the test run ........................................................ 9
2. About the product ....................................................................................... 9
3. Specifications .............................................................................................. 9
4. Confirmation of parts attached ................................................................. 10
5. Lifting method ........................................................................................... 10
6. Installation of unit and service space ........................................................ 10
6.1. Installation ............................................................................... 10
6.2. Service space .......................................................................... 10
7. Water pipe installation ............................................................................... 11
7.1. Precautions during installation ................................................ 11
7.2. Insulation installation ............................................................... 11
7.3. Water processing and water quality control ............................. 11
7.4. Pump interlock ......................................................................... 11
8. Refrigerant piping installation ...................................................................
8.1. Caution ....................................................................................
8.2. Refrigerant piping system ........................................................
9. Additional refrigerant charge .....................................................................
9.1. Calculation of additional refrigerant charge .............................
9.2. Precautions concerning piping connection and
valve operation ........................................................................
9.3. Airtight test, evacuation, and refrigerant charging ...................
9.4. Thermal insulation of refrigerant piping ...................................
10. Wiring ........................................................................................................
10.1. Caution ....................................................................................
10.2. Control box and connecting position of wiring .........................
10.3. Wiring transmission cables ......................................................
10.4. Wiring of main power supply and equipment capacity ............
11. Test run .....................................................................................................
11.1. The following phenomena do not represent trouble
(emergency) ............................................................................
12. Information on rating plate ........................................................................
12
12
12
12
12
13
14
14
15
15
15
16
17
18
18
18
GB
1. Safety precautions
1.1. Before installation and electric work
D
s Before installing the unit, make sure you read all the “Safety
precautions”.
s The “Safety precautions” provide very important points regarding safety. Make sure you follow them.
•
•
F
Symbols used in the text
Warning:
•
Describes precautions that should be observed to prevent danger of injury
or death to the user.
E
Caution:
Describes precautions that should be observed to prevent damage to the
unit.
•
Symbols used in the illustrations
I
: Indicates an action that must be avoided.
•
: Indicates that important instructions must be followed.
: Indicates a part which must be grounded.
NL
: Beware of electric shock. (This symbol is displayed on the main unit label.)
<Color: yellow>
Warning:
P
Carefully read the labels affixed to the main unit.
GR
•
•
RU
•
•
Warning:
•
•
TR
•
•
•
•
•
•
Ask the dealer or an authorized technician to install the air conditioner.
- Improper installation by the user may result in water leakage, electric shock,
or fire.
Install the unit in a place that can withstand its weight.
- Inadequate strength may cause the unit to fall down, resulting in injuries.
Use the specified cables for wiring. Make the connections securely so
that the outside force of the cable is not applied to the terminals.
- Inadequate connection and fastening may generate heat and cause a fire.
Prepare for rain and other moisture and earthquakes and install the unit
at the specified place.
- Improper installation may cause the unit to topple over and result in injury.
Always use an filter and other accessories specified by Mitsubishi Electric.
- Ask an authorized technician to install the accessories. Improper installation
by the user may result in water leakage, electric shock, or fire.
Never repair the unit. If the air conditioner must be repaired, consult the
dealer.
- If the unit is repaired improperly, water leakage, electric shock, or fire may
result.
If refrigerant gas leaks during installation work, ventilate the room.
- If the refrigerant gas comes into contact with a flame, poisonous gases will
be released.
Install the air conditioner according to this Installation Manual.
- If the unit is installed improperly, water leakage, electric shock, or fire may
result.
Have all electric work done by a licensed electrician according to “Electric Facility Engineering Standard” and “Interior Wire Regulations”and
the instructions given in this manual and always use a special circuit.
8
•
- If the power source capacity is inadequate or electric work is performed improperly, electric shock and fire may result.
Securely install the heat source unit terminal cover (panel).
- If the terminal cover (panel) is not installed properly, dust or water may enter
the heat source unit and fire or electric shock may result.
When installing and moving the air conditioner to another site, do not
charge it with a refrigerant different from the refrigerant (R410A) specified on the unit.
- If a different refrigerant or air is mixed with the original refrigerant, the refrigerant cycle may malfunction and the unit may be damaged.
If the air conditioner is installed in a small room, measures must be taken
to prevent the refrigerant concentration from exceeding the safety limit
even if the refrigerant should leak.
- Consult the dealer regarding the appropriate measures to prevent the safety
limit from being exceeded. Should the refrigerant leak and cause the safety
limit to be exceeded, hazards due to lack of oxygen in the room could result.
When moving and reinstalling the air conditioner, consult the dealer or
an authorized technician.
- If the air conditioner is installed improperly, water leakage, electric shock, or
fire may result.
After completing installation work, make sure that refrigerant gas is not
leaking.
- If the refrigerant gas leaks and is exposed to a fan heater, stove, oven, or
other heat source, it may generate noxious gases.
Do not reconstruct or change the settings of the protection devices.
- If the pressure switch, thermal switch, or other protection device is shorted
and operated forcibly, or parts other than those specified by Mitsubishi Electric are used, fire or explosion may result.
To dispose of this product, consult your dealer.
The installer and system specialist shall secure safety against leakage
according to local regulation or standards.
- Following standards may be applicable if local regulation are not available.
Pay a special attention to the place, such as a basement, etc. where refrigeration gas can stay, since refrigeration is heavier than the air.
1.2. Precautions for devices that use R410A
refrigerant
Caution:
•
•
•
•
Do not use the existing refrigerant piping.
- The old refrigerant and refrigerator oil in the existing piping contains a large
amount of chlorine which may cause the refrigerator oil of the new unit to
deteriorate.
- R410A is a high-pressure refrigerant and can cause the existing piping to
burst.
Use refrigerant piping made of phosphorus deoxidized copper and copper alloy seamless pipes and tubes. In addition, be sure that the inner
and outer surfaces of the pipes are clean and free of hazardous sulphur,
oxides, dust/dirt, shaving particles, oils, moisture, or any other contaminant.
- Contaminants on the inside of the refrigerant piping may cause the refrigerant residual oil to deteriorate.
Store the piping to be used during installation indoors and keep both
ends of the piping sealed until just before brazing. (Store elbows and
other joints in a plastic bag.)
- If dust, dirt, or water enters the refrigerant cycle, deterioration of the oil and
compressor trouble may result.
Use ester oil, ether oil or alkylbenzene (small amount) as the refrigerator
oil to coat flares and flange connections.
- The refrigerator oil will degrade if it is mixed with a large amount of mineral
oil.
•
•
•
1.3. Before getting installed
Caution:
•
•
•
•
•
Do not install the unit where combustible gas may leak.
- If the gas leaks and accumulates around the unit, an explosion may result.
Do not use the air conditioner where food, pets, plants, precision instruments, or artwork are kept.
- The quality of the food, etc. may deteriorate.
Do not use the air conditioner in special environments.
- Oil, steam, sulfuric smoke, etc. can significantly reduce the performance of
the air conditioner or damage its parts.
When installing the unit in a hospital, communication station, or similar
place, provide sufficient protection against noise.
- The inverter equipment, private power generator, high-frequency medical
equipment, or radio communication equipment may cause the air conditioner
to operate erroneously, or fail to operate. On the other hand, the air conditioner may affect such equipment by creating noise that disturbs medical
treatment or image broadcasting.
Do not install the unit on a structure that may cause leakage.
- When the room humidity exceeds 80 % or when the drain pipe is clogged,
condensation may drip from the indoor unit. Perform collective drainage work
together with the heat source unit, as required.
1.4. Before installation electrical work
•
1.5. Before starting the test run
Caution:
•
•
•
Warning:
When installing or relocating the unit, make sure that no substance other
than the specified refrigerant (R410A) enters the refrigerant circuit. Any presence of foreign substance such as air can cause abnormal pressure rise or
explosion.
•
•
Caution:
Ground the unit.
- Do not connect the ground wire to gas or water pipes, lightning rods, or
telephone ground lines. Improper grounding may result in electric shock.
•
Turn on the power at least 12 hours before starting operation.
- Starting operation immediately after turning on the main power switch can
result in severe damage to internal parts. Keep the power switch turned on
during the operational season.
Do not touch the switches with wet fingers.
- Touching a switch with wet fingers can cause electric shock.
Do not touch the refrigerant pipes during and immediately after operation.
- During and immediately after operation, the refrigerant pipes are may be hot
and may be cold, depending on the condition of the refrigerant flowing through
the refrigerant piping, compressor, and other refrigerant cycle parts. Your
hands may suffer burns or frostbite if you touch the refrigerant pipes.
Do not operate the air conditioner with the panels and guards removed.
- Rotating, hot, or high-voltage parts can cause injuries.
Do not turn off the power immediately after stopping operation.
- Always wait at least five minutes before turning off the power. Otherwise,
water leakage and trouble may occur.
Do not touch the surface of the compressor during servicing.
- If unit is connected to the supply and not running, crank case heater at
compressor is operating.
GR
•
GB
•
D
•
F
•
•
E
•
•
I
•
•
The reverse phase of L lines (L1, L2, L3) can be detected (Error cord: 4103),
but the reverse phase of L lines and N line can be not be detected.
- The some electric parts should be damaged when power is supplied under
the miss wiring.
Install the power cable so that tension is not applied to the cable.
- Tension may cause the cable to break and generate heat and cause a fire.
Install a leak circuit breaker, as required.
- If a leak circuit breaker is not installed, electric shock may result.
Use power line cables of sufficient current carrying capacity and rating.
- Cables that are too small may leak, generate heat, and cause a fire.
Use only a circuit breaker and fuse of the specified capacity.
- A fuse or circuit breaker of a larger capacity or a steel or copper wire may
result in a general unit failure or fire.
Do not wash the air conditioner units.
- Washing them may cause an electric shock.
Be careful that the installation base is not damaged by long use.
- If the damage is left uncorrected, the unit may fall and cause personal injury
or property damage.
Install the drain piping according to this Installation Manual to ensure
proper drainage. Wrap thermal insulation around the pipes to prevent
condensation.
- Improper drain piping may cause water leakage and damage to furniture
and other possessions.
Be very careful about product transportation.
- Only one person should not carry the product if it weighs more than 20 kg.
- Some products use PP bands for packaging. Do not use any PP bands for a
means of transportation. It is dangerous.
- When transporting the heat source unit, support it at the specified positions
on the unit base. Also support the heat source unit at four points so that it
cannot slip side ways.
Safely dispose of the packing materials.
- Packing materials, such as nails and other metal or wooden parts, may cause
stabs or other injuries.
- Tear apart and throw away plastic packaging bags so that children will not
play with them. If children play with a plastic bag which was not torn apart,
they face the risk of suffocation.
NL
•
•
P
•
Use liquid refrigerant to fill the system.
- If gas refrigerant is used to seal the system, the composition of the refrigerant in the cylinder will change and performance may drop.
Do not use a refrigerant other than R410A.
- If another refrigerant (R22, etc.) is mixed with R410A, the chlorine in the
refrigerant may cause the refrigerator oil to deteriorate.
Use a vacuum pump with a reverse flow check valve.
- The vacuum pump oil may flow back into the refrigerant cycle and cause the
refrigerator oil to deteriorate.
Do not use the following tools that are used with conventional refrigerants.
(Gauge manifold, charge hose, gas leak detector, reverse flow check valve,
refrigerant charge base, refrigerant recovery equipment)
- If the conventional refrigerant and refrigerator oil are mixed in the R410A,
the refrigerant may deteriorated.
- If water is mixed in the R410A, the refrigerator oil may deteriorate.
- Since R410A does not contain any chlorine, gas leak detectors for conventional refrigerants will not react to it.
Do not use a charging cylinder.
- Using a charging cylinder may cause the refrigerant to deteriorate.
Be especially careful when managing the tools.
- If dust, dirt, or water gets in the refrigerant cycle, the refrigerant may deteriorate.
2. About the product
This unit uses R410A-type refrigerant
•
Piping for systems using R410A may be different from that for systems using
conventional refrigerant because the design pressure in systems using R410A
is higher. Refer to Data Book for more information.
•
•
Some of the tools and equipment used for installation with systems that use
other types of refrigerant cannot be used with the systems using R410A. Refer
to Data Book for more information.
Do not use the existing piping, as it contains chlorine, which is found in conventional refrigerating machine oil and refrigerant. This chlorine will deteriorate
the refrigerant machine oil in the new equipment. The existing piping must not
be used as the design pressure in systems using R410A is higher than that in
the systems using other types of refrigerant and the existing pipes may burst.
TR
•
RU
•
3. Specifications
PQHY-P400YSGM-A
50 dB <A>
Model
Noise level
Net weight
Compressor unit
Heat exchanger unit
Allowable pressure
Refrigerant (Compressor unit side only)
Total capacity
Indoor units
Model / Quantity
Operation temperature
PQHY-P500YSGM-A
53 dB <A>
PQY-P01YGM-A: 208 kg
PQHY-P400YGM-A: 244 kg
PQHY-P500YGM-A: 248 kg
HP: 4.15 MPa, LP: 2.21 MPa
R410A: 12.0 kg
50 ~ 130 %
P20 ~ P250 / 1 ~ 22
P20 ~ P250 / 1 ~ 24
Water temperature: 10˚C ~ 45˚C
9
4. Confirmation of parts attached
Model
Model
Model
PQY-P01YGM-A
PQHY-P400/P500YGM-A
PQY-P01YGM-A
PQHY-P400/P500YGM-A
1 Connecting pipe for heat
exchanger unit
(Low press side ø28.58)
–
1 pc. (*)
5 Connecting pipe
(Compressor unit - Heat
exchanger unit ø19.05)
1 pc.
1 pc.
2 Connecting pipe
(Compressor unit - Heat
exchanger unit ø28.58)
1 pc. (*)
1 pc.
3 Connecting pipe for heat
exchanger unit
(High press side ø22.2)
–
1 pc. (*)
4 Connecting pipe
(Compressor unit - Heat
exchanger unit ø9.52)
1 pc.
1 pc.
6 Packing
(inside ø23, outside ø35)
7 Bushing (ø27)
8 Bushing (ø38)
1 pc.
2 pcs.
1 pc.
–
1 pc.
–
9 External heater adapter
(3-wire)
0 External heater adapter
(1-wire)
1 pc.
–
–
1 pc.
PQY-P01YGM-A
PQHY-P400/P500YGM-A
* Fixed with the unit
GB
5. Lifting method
[Fig. 5.0.1] (P.2)
6. Installation of unit and service space
6.1. Installation
6.2. Service space
•
•
Using the anchoring holes shown below, firmly bolt the unit to the base.
[Fig. 6.1.1] (P.2)
E
F
D
Caution:
Be very careful when carrying the product.
- Do not have only one person to carry product if it is more than 20 kg.
- PP bands are used to pack some products. Do not use them as a mean for transportation because they are dangerous.
- Tear plastic packaging bag and scrap it so that children cannot play with it. Otherwise plastic packaging bag may suffocate children to death.
- When carrying the heat source unit, be sure to support it at four points. Carrying with 3-point support may make the heat source unit unstable, resulting in it falling.
<A> Side-by-side installation
Please allow for the following service spaces after installation.
(All servicing can be performed from the front of the unit)
[Fig. 6.2.1] (P.2)
<B> Back-to-back installation
<A> Side-by-side installation
Heat exchanger unit
B
Compressor unit
<B> Back-to-back installation
C
4-ø14 (Anchoring hole)
D
(Top view)
A
Piping space (for side piping)
*1
Select an installation site that is level and free from vibrations so that the side
panels of the units do not rub against each other.
B
Heat exchanger unit
C
Compressor unit
Select an installation site that allows the fixation of the units to the floor.
D
Service space (front side)
Bases and anti-vibration
E
(Top view)
•
Be sure to install unit in a place strong enough to withstand its weight. If the
base is unstable, reinforce with a concrete base.
F
Piping space
*1
•
The unit must be anchored on a level surface. Use a level to check after
installation.
Select an installation site that is level and free from vibrations so that the side
panels of the units do not rub against each other.
*2
Select an installation site that allows the fixation of the units to the floor.
I
A
P
NL
*2
•
Anti-vibration pads must be placed under the base of the unit.
•
If the unit is installed near a room where noise is a problem, using an antivibration stand on the base of the unit is recommended.
GR
RU
F
Concrete base
Warning:
•
•
•
TR
Anti-vibration pad etc.
•
Be sure to install unit in a place strong enough to withstand its weight.
Any lack of strength may cause unit to fall down, resulting in a personal
injury.
Have installation work in order to protect against earthquake.
Any installation deficiency may cause unit to fall down, resulting in a
personal injury.
In the case of a side-by-side installation of a compressor unit and a heat
exchanger unit, leave a space of at least 10 mm between them.
When they are installed too closely together, they may rub against each
other and generate noise.
In the case of a back-to-back installation of a compressor unit and a heat
exchanger unit, leave a space of at least 50 mm between them.
If they are installed to closely together, there may not be enough space
for using the tools to anchor the units to the base.
10
<A> Side-by-side installation
<B> Sample back-to-back installation
[Fig. 6.1.2] (P.2)
E
[Fig. 6.2.2] (P.3)
G
Piping space (for top piping)
H
Piping space (for side piping)
I
Heat exchanger unit
J
Compressor unit
K
Field-installed pipes
Bypass pipe
ø9.52 (Flare + Brazed)
High press pipe ø19.05 (Flare + Brazed)
Low press pipe ø25.4 (Flange + Brazed)
Connecting wire between heat exchanger unit and compressor unit (External
heater adapter*)
Control signal wire (connector, on-site connection)
* If the space between the heat exchanger unit and compressor unit exceeds
1.5 m (the length of the standard supplied external heater adapter), an optional external heater adapter (available in 5m or10m) is necessary.
L
M
(Front view)
N
Service space (Heat exchanger unit side)
O
Service space (Compressor unit side)
P
Piping space
Q
Pipe/wire output port
R
(Side view)
*1
Select an installation site that is level and free from vibrations so that the side
panels of the units do not rub against each other.
*2
Select an installation site that allows the fixation of the units to the floor.
7. Water pipe installation
City Multi WR2 Series pipes are similar to other air-conditioning pipes, however, please observe the following precautions during installation.
sealant particles, or rust, do not enter the pipes.
•
There is a water vent plug in the center of the heat exchanger water inlet head
at the middle of the unit. Use this for maintenance, etc.
In addition, do not allow any of the unit’s electrical parts (such as the solenoid
valve coil or compressor power supply) to become wet.
•
Install a back flow-prevention valve on the pump and a flexible joint to prevent
excess vibration.
•
Use a sleeve to protect the pipes where they go through a wall.
•
Use metal fittings to secure the pipes, and install them so that they have maximum protection against breakage and bending.
•
Do not confuse the water intake and outlet valves.
•
This unit doesn’t have any heater to prevent freezing within tubes. When the
water flow is stopped on low ambient, take out the water from tubes.
•
The unused knockout holes should be closed and the opening of refrigerant
pipes, water pipes, power source and transmission wires should be filled with
putty and so on to prevent from rain. (field construction)
Example of heat source unit installation (using left piping)
pH (25˚C)
Electric conductivity (mS/m) (25˚C)
(µ s/cm) (25˚C)
Chloride ion
(mg Cl-/r)
(mg SO42-/r)
Standard Sulfate ion
Acid consumption (pH4.8)
items
(mg CaCO3/r)
Total hardness
(mg CaCO3/r)
Calcium hardness (mg CaCO3/r)
Ionic silica
(mg SiO2/r)
Iron
(mg Fe/r)
Copper
(mg Cu/r)
Reference
items
[Fig. 7.1.1] (P.3)
A
Water circulation pipe
B
Close valve
C
Close valve
D
Water outlet
E
Refrigerant piping
F
Y-type strainer
G
Water inlet
H
Drain pipe
I
Heat exchanger unit
J
Compressor unit
7.2. Insulation installation
With City Multi WR2 Series piping, as long as the temperature range of the circulating water is kept to average temperatures year-round (30°C in the summer, 20°C
in the winter), there is no need to insulate or otherwise protect indoor piping from
exposure. You should use insulation in the following situations:
•
Any heat source piping.
•
Indoor piping in cold-weather regions where frozen pipes are a problem.
•
When air coming from the outside causes condensation to form on piping.
•
Any drainage piping.
7.3. Water processing and water quality control
To preserve water quality, use the closed type of cooling tower for WR2. When the
circulating water quality is poor, the water heat exchanger can develop scales,
leading to a reduction in heat-exchange power and possible corrosion of the heat
exchanger. Please pay careful attention to water processing and water quality control when installing the water circulation system.
•
Removal of foreign objects or impurities within the pipes.
During installation, be careful that foreign objects, such as welding fragments,
Sulfide ion
(mg S2-/r)
+
Ammonium ion
(mg NH4 /r)
Residual chlorine
(mg Cl/r)
Free carbon dioxide (mg CO2/r)
Ryzner stability index
50 or less
50 or less
70 or less
50 or less
30 or less
1.0 or less
1.0 or less
not to be
detected
0.3 or less
0.25 or less
0.4 or less
–
70 or less
50 or less
30 or less
0.3 or less
0.1 or less
not to be
detected
0.1 or less
0.3 or less
4.0 or less
–
GB
•
Items
Lower mid-range
Tendency
temperature water system
Recirculating
ScaleMake-up
water
Corrosive forming
water
[20<T=60˚C]
7.0 ~ 8.0
7.0 ~ 8.0
30 or less 30 or less
[300 or less] [300 or less]
50 or less 50 or less
50 or less 50 or less
D
Compressed water may form in the low-temperature sections of heat source
unit. Use a drainage pipe connected to the drain valve at the base of the unit to
drain the water.
F
•
2 Water quality standard
E
Install a suitable air vent on the water pipe. After sending water through the
pipe, be sure to vent the excess air.
Reference : Guideline of Water Quality for Refrigeration and Air Conditioning
Equipment. (JRA GL02E-1994)
3 Please consult with a water quality control specialist about water quality
control methods and water quality calculations before using anti-corrosive
solutions for water quality management.
4 When replacing a previously installed air conditioning device (even when
only the heat exchanger is being replaced), first conduct a water quality
analysis and check for possible corrosion.
Corrosion can occur in cold-water systems even if there has been no prior
signs of corrosion.
If the water quality level has dropped, please adjust water quality sufficiently before replacing the unit.
7.4. Pump interlock
I
•
NL
To insure easy maintenance, inspection, and replacement of the unit, use a
proper joint, valve, etc. on the water intake and outlet port. In addition, be sure
to install a strainer on the water intake pipe. (In order to maintain the heat
source unit, a strainer on the circulating water inlet is necessary.)
* An example of the heat source unit installation is shown in the diagram below.
P
Use the reverse-return method to insure proper pipe resistance to each unit.
•
The heat source unit may become damaged if it is operated with no water circulating through the pipes.
Be sure to interlock unit operation and the water-circuit pump. Use the terminal
blocks for interlocking (TB8-3, 4) that can be found on the unit.
In the case of a pump interlock circuit signal connection to the TB8-3, 4, remove
the short-circuit wire. Also, to prevent mistaken error detection, resulting from a
poor connection, in the pressure valve 63PW, use a low maintained current of 5mA
or less.
GR
•
Water Quality Processing
1 Depending on the quality of the cold-temperature water used in the airconditioner, the copper piping of the heat exchanger may become corroded. We recommend regular water quality processing.
Cold water circulation systems using open heat storage tanks are particularly prone to corrosion.
When using an open-type heat storage tank, install a water-to-water heat
exchanger, and use a closed-loop circuit on the air conditioner side. If a
water supply tank is installed, keep contact with air to a minimum, and
keep the level of dissolved oxygen in the water no higher than 1mg/r.
[Fig. 7.4.1] (P.3)
A
Short-circuit wire (Connected before delivery from manufacturer)
B
Pump interlock circuit connection
RU
7.1. Precautions during installation
TR
•
11
8. Refrigerant piping installation
City Multi WR2 Series is constituted by an end branching system in which the
refrigerant piping from heat source unit is branched at BC controller and connected
to each indoor unit.
The connection method adapted is brazing connection for high pressure pipe and
low pressure pipe between heat source unit and BC controller, and flare connection between BC controller and indoor unit. Brazing connection is employed for
joint pipe set and branch pipe set.
Warning:
Always use extreme care to prevent the refrigerant gas from leaking while
using fire or flame. If the refrigerant gas comes in contact with a flame from
any source, such as a gas stove, it breaks down and generates a poisonous
gas which can cause gas poisoning. Never weld in an unventilated room.
Always conduct an inspection for gas leakage after installation of the refrigerant piping has been completed.
A Residues in commercially available antioxidants may have adverse effects on
the equipment. Braze only with non-oxide brazing material. The use of other
brazing material may result in compressor damage.
(Refer to item 9.2. for detailed information on pipe connections and valve operations.)
B Never perform heat source unit piping connection work when it is raining.
Warning
When installing and moving the unit, do not charge it with refrigerant other
than the refrigerant specified on the unit.
- Mixing of a different refrigerant, air, etc. may cause the refrigerant cycle to malfunction and result in severe damage.
Caution:
•
8.1. Caution
D
GB
This unit uses refrigerant R410A. Follow the local regulations on materials and
pipe thickness when selecting pipes.
2 Commercially available piping often contains dust and other materials. Always
blow it clean with a dry inert gas.
4 Reduce the number of bending portions as much as possible, and make bending radius as big as possible.
5 Always observe the restrictions on the refrigerant piping (such as rated length,
the difference between high/low pressures, and piping diameter). Failure to do
so can result in equipment failure or a decline in heating/cooling performance.
6 Either a lack or an excess of refrigerant causes the unit to make an emergency
stop. Charge the system with an appropriate amount of refrigerant. At such a
time, always properly charge the unit. When servicing, always check the notes
concerning pipe length and amount of additional refrigerant at both locations,
the refrigerant volume calculation table on the back of the service panel and
the additional refrigerant section on the labels for the combined number of
indoor units.
I
E
F
3 Use care to prevent dust, water or other contaminants from entering the piping
during installation.
7 Use liquid refrigerant to fill the system.
RU
GR
P
NL
8 Never use refrigerant to perform an air purge. Always evacuate using a vacuum
pump.
TR
•
1 Use the following materials for refrigeration piping.
• Material: Use refrigerant piping made of phosphorus deoxidized copper.
In addition, be sure that the inner and outer surfaces of the pipes are clean
and free of hazardous sulphur, oxides, dust/dirt, shaving particles, oils,
moisture, or any other contaminant.
•
•
•
•
•
Use a vacuum pump with a reverse flow check valve.
- If the vacuum pump does not have a reverse flow check valve, the vacuum
pump oil may flow back into the refrigerant cycle and cause deterioration of
the refrigerator oil and other trouble.
Do not use the tools shown below used with conventional refrigerant.
(Gauge manifold, charge hose, gas leak detector, check valve, refrigerant
charge base, vacuum gauge, refrigerant recovery equipment)
- Mixing of conventional refrigerant and refrigerator oil may cause the refrigerator oil to deteriorate.
- Mixing of water will cause the refrigerator oil to deteriorate.
- R410A refrigerant does not contain any chlorine. Therefore, gas leak detectors for conventional refrigerants will not react to it.
Manage the tools more carefully than normal.
- If dust, dirt, or water gets in the refrigerant cycle, the refrigerator oil will deteriorate.
Never use existing refrigerant piping.
- The large amount of chlorine in conventional refrigerant and refrigerator oil
in the existing piping will cause the new refrigerant to deteriorate.
Store the piping to be used during installation indoors and keep both
ends of the piping sealed until just before brazing.
- If dust, dirt, or water gets into the refrigerant cycle, the oil will deteriorate and
the compressor may fail.
Do not use a charging cylinder.
- Using a charging cylinder may cause the refrigerant to deteriorate.
Do not use special detergents for washing piping.
8.2. Refrigerant piping system
Connection Example
[Fig. 8.2.1] (P.4)
Å
Heat source model
ı
Liquid pipe
Ç
Gas pipe
Î
Total capacity of indoor units
9 Always insulate the piping properly. Insufficient insulation will result in a decline in heating/cooling performance, water drops from condensation and other
such problems.
‰
Model number
Ï
Downstream unit model total
Ì
Branch kit model
Ó
The 1st branch of P450 ~ P650
¬
= 200)
4-Branching header (Downstream unit model total <
0 When connecting the refrigerant piping, make sure the ball valve of the heat
source unit is completely closed (the factory setting) and do not operate it until
the refrigerant piping for the heat source and indoor units has been connected,
a refrigerant leakage test has been performed and the evacuation process has
been completed.
Ô
= 400)
8-Branching header(Downstream unit model total <
= 650)
10-Branching header (Downstream unit model total <
Ò
High press pipe
ˆ
Bypass pipe
˜
Low press pipe
A
C
Heat source unit
B
First branch
Indoor unit
D
Cap
9. Additional refrigerant charge
At the time of shipping, the heat source unit is charged with the refrigerant. As this
charge does not include the amount needed for extended piping, additional charging for each refrigerant line will be required on site. In order that future servicing
may be properly provided, always keep a record of the size and length of each
refrigerant line and the amount of additional charge by writing it in the space provided on the heat source unit.
9.1. Calculation of additional refrigerant
charge
•
Calculate the amount of additional charge based on the length of the piping
extension and the size of the refrigerant line.
•
Use the table to the below as a guide to calculating the amount of additional
charging and charge the system accordingly.
•
If the calculation results in a fraction of less than 0.1 kg, round up to the next
0.1 kg. For example, if the result of the calculation was 19.58 kg, round the
result up to 19.6 kg.
12
<Additional Charge>
Additional
Liquid pipe size
Liquid pipe size
Liquid pipe size
refrigerant
Total length of
Total length of
Total length of
= ø15.88 × 0.20 + ø12.7 × 0.12
+ ø9.52 × 0.06
charge
(m) × 0.20 (kg/m)
(kg)
(m) × 0.12 (kg/m)
(m) × 0.06 (kg/m)
Liquid pipe size
Total length of
+ ø6.35 × 0.024 + α1 + α2
(m) × 0.024 (kg/m)
Outdoor: 500
Indoor No. 1:
No. 2:
No. 3:
No. 4:
No. 5:
100
100
40
32
250
A:
B:
C:
D:
E:
ø15.88
ø15.88
ø12.7
ø9.52
ø19.05
40 m
10 m
10 m
10 m
5m
a:
b:
c:
d:
e:
ø9.52
ø9.52
ø6.35
ø6.35
ø9.52
10 m
5m
10 m
10 m
10 m
At the
conditions
below:
The total length of each liquid line is as follows:
ø19.05: E = 5 m
ø15.88: A + B = 40 + 10 = 50 m
ø12.7: C = 10 m
ø9.52: D + a + b + e = 10 + 10 + 5 + 10 = 35 m
ø6.35: c + d = 10 + 10 = 20 m
flare nut size (mm)
outer diameter
size in inches
ø6.35
ø9.52
ø12.70
ø15.88
ø19.05
1/4"
3/8"
1/2"
5/8"
3/4"
B
Therefore,
<Calculation example>
Additional refrigerant charge
= 5 × 0.16 + 50 × 0.20 + 10 × 0.12 + 35 × 0.06 + 20 × 0.024 + 3.0 + 2.0 = 19.6 kg
dimension B
R410A
17.0
22.0
26.0
29.0
36.0
[Fig. 9.2.2] (P.4)
Value of α1
<A> [Ball valve (Low press. side/flanged type)]
α1
1.0 kg
1.5 kg
2.0 kg
2.5 kg
3.0 kg
4.0 kg
5.0 kg
<B> [Ball valve (High press. side/flared type)]
Stopper pin [Prevents the valve stem from turning 90° or more.]
C
Packing (Accessory)
[Manufacturer: Nichiasu corporation]
[Type: T/#1991-NF]
D
Connecting pipe (Accessory)
[Use packing and securely install this pipe to the valve flange so that gas leakage
will not occur. (Tightening torque:40 N·m) Coat both surfaces of the packing with
refrigerating machine oil. (Ester oil, ether oil or alkylbenzene [small amount])]
9.2. Precautions concerning piping connection and valve operation
E
Open (Operate slowly)
F
Cap, copper packing
[Remove the cap and operate the valve stem. Always reinstall the cap after operation is completed. (Valve stem cap tightening torque: 23 ~ 27 N·m)]
•
The compressor unit is charged with refrigerant at factory shipment, but the
heat exchanger unit is not. (The heat exchanger unit is charged with inert gas.)
G
•
Conduct piping connection and valve operation accurately.
•
Flange type side connecting pipe is assembled in factory before shipment.
Service port
[Use this port to evacuate the refrigerant piping and add an additional charge at
the site.
Open and close the port using a double-ended wrench.
Always reinstall the cap after operation is completed. (Service port cap tightening
torque: 12 ~ 15 N·m)]
H
ø12.7 (PQHY-P400)
ø15.88 (PQHY-P500)
I
ø28.58 (PQHY-P400)
ø28.58 (PQHY-P500)
J
Field piping
Value of α2
α2
0 kg
2.0 kg
1 For brazing to the connecting pipe with flange, remove the connecting pipe
with flange from the ball valve, and braze it outside of the unit.
2 During the time when removing the connecting pipe with flange, remove
the seal attached on the rear side of this sheet and paste it onto the flange
surface of the ball valve to prevent the entry of dust into the valve.
3 The refrigerant circuit is closed with a round, close-packed packing upon
shipment to prevent gas leak between flanges. As no operation can be
done under this state, be sure to replace the packing with the hollow packing attached at the piping connection.
[Fig. 9.2.3] (P.4)
Close-packed packing
B
Hollow packing
•
•
After evacuation and refrigerant charge, ensure that the handle is fully open. If
operating with the valve closed, abnormal pressure will be imparted to the
high- or low-pressure side of the refrigerant circuit, giving damage to the compressor, four-way valve, etc.
•
Determine the amount of additional refrigerant charge by using the formula,
and charge refrigerant additionally through the service port after completing
piping connection work.
•
After completing work, tighten the service port and cap securely not to generate gas leak.
•
Flare machining dimension for systems using R410A is larger than that for
systems using other types of refrigerant in order to increase the air tightness.
•
Refer to the table on the below for flare machining dimensions, and follow the
regulations set forth by the local authorities. Seal off the opening of the pipe
with a closure material (not supplied) to keep small animals from entering the
pipe if that is a concern.
A
flare machining dimension (mm)
outer diameter
size in inches
ø6.35
ø9.52
ø12.70
ø15.88
ø19.05
1/4"
3/8"
1/2"
5/8"
3/4"
dimension A
R410A
9.1
13.2
16.6
19.7
24.0
Liquid pipe
E
Heat exchanger unit – Compressor unit connection pipe (ø28.58 Flange + Brazed)
I
Gas pipe
D
F
Heat exchanger unit – Compressor unit connection pipe (ø19.05 Flare + Brazed)
G
Heat exchanger unit – Compressor unit connection pipe (ø9.52 Flare + Brazed)
H
Ball valve
I
External heater adapter (3-wire)
Connect the pipes on the compressor unit and heat exchanger unit on site.
Pipe sizes are shown below.
Perform piping work according to the instructions in section 9.4 Thermal insulation of refrigerant piping.
Appropriate tightening torque by torque wrench:
Copper pipe external dia. (mm)
ø6.35
ø9.52
ø12.7
ø15.88
ø19.05
Tightening torque (N·m)
14 to 18
35 to 42
50 to 57.5
75 to 80
100 to 140
RU
A
Compressor unit
C
NL
[Fig. 9.2.1] (P.4)
Heat exchanger unit
B
P
4 At the mounting of the hollow packing, wipe off dust attached on the flange
sheet surface and the packing. Coat refrigerating machine oil (Ester oil,
ether oil or alkylbenzene [small amount]) onto both surfaces of the packing.
A
Tightening angle standard:
Pipe diameter (mm)
ø6.35, ø9.52
ø12.7, ø15.88
ø19.05
Tightening angle (°)
60 to 90
30 to 60
20 to 35
TR
PQHY-P400YSGM-A
PQHY-P500YSGM-A
D
B
F
Valve stem
[Fully closed at the factory, when connecting the piping, when evacuating, and
when charging additional refrigerant. Open fully after the operations above are
completed.]
E
A
GB
<C> This figure shows the valve in the fully open state.
GR
Total capacity of connecting indoor units
to Model 80
Models 81 to 160
Models 161 to 330
Models 331 to 480
Models 481 to 630
Models 631 to 710
Models 711 to 890
[Fig. 9.2.4] (P.4)
13
Note:
If a torque wrench is not available, use the following method as a standard:
When you tighten the flare nut with a wrench, you will reach a point where
the tightening torque will abruptly increase. Turn the flare nut beyond this
point by the angle shown in the table above.
Caution:
•
•
•
•
Always remove the connecting pipe from the ball valve and braze it outside the unit.
- Brazing the connecting pipe while it is installed will heat the ball valve and
cause trouble or gas leakage. The piping, etc. inside the unit may also be
burned.
Use ester oil, ether oil or alkylbenzene (small amount) as the refrigerating machine oil to coat flares and flange connections.
- The refrigerating machine oil will degrade if it is mixed with a large amount of
mineral oil.
Keep the ball valve closed until refrigerant charging to the pipes to be
added on site has been completed. Opening the valve before charging
the refrigerant may result in unit damage.
Do not use a leak detection additive.
P
NL
I
E
F
D
GB
9.3. Airtight test, evacuation, and refrigerant
charging
1 Airtight test
Evacuate the connecting pipes and indoor units through the service port on
the ball valve of the heat exchanger unit with a vacuum pump with the ball
valve on the compressor unit closed and the ball valve on the heat exchanger
open as shown in the figure below. (Be sure to vacuum through the service
port on both the liquid and gas pipes.)
[Fig. 9.3.1] (P.5)
<A> Open
<B> Closed
A
Nitrogen gas
B
To indoor unit
C
System analyzer
D
Lo knob
E
Hi knob
F
Ball valve
G
Liquid pipe
H
Gas pipe
I
Heat source unit
J
Service port
K
Heat exchanger unit
L
Compressor unit
Observe the following restrictions when conducting an air tightness test to prevent
negative effects on the refrigerating machine oil. Also, with nonazeotropic refrigerant (R410A), gas leakage causes the composition to change and affects performance. Therefore, perform the airtightness test cautiously.
Caution:
Airtight test procedure
Restriction
1. Nitrogen gas pressurization
(1) After pressurizing to the design pressure (4.15 MPa) using nitrogen gas, allow it to stand for
about one day. If the pressure does not drop, airtightness is good.
However, if the pressure drops, since the leaking point is unknown, the following bubble test
may also be performed.
(2) After the pressurization described above, spray the flare connection parts, brazed parts, flanges,
and other parts that may leak with a bubbling agent (Kyuboflex, etc.) and visually check for
bubbles.
(3) After the airtight test, wipe off the bubbling agent.
• If a flammable gas or air (oxygen) is used as the pressurization
gas, it may catch fire or explode.
2. Pressurization using refrigerant gas and nitrogen gas
(1) Pressurizing to a gas pressure of approximately 0.2 MPa, pressurize to the design pressure
(4.15 MPa) using nitrogen gas.
However, do not pressurize at one time. Stop during pressurization and check that the pressure does not drop.
(2) Check for gas leaks by checking the flare connection parts, brazed parts, flanges, and other
parts which may leak using an R410A compatible electric leak detector.
(3) This test may be used together the with bubble type gas leak test.
• Do not use a refrigerant other than that indicated on the unit.
• Sealing with gas from a cylinder will cause the composition of
the refrigerant in the cylinder to change.
• Use a pressure gauge, charging hose, and other parts especially
for R410A.
• An electric leak detector for R22 cannot detect leaks of R410A.
• Do not use a haloid torch. (Leaks cannot be detected.)
Only use refrigerant R410A.
- The use of other refrigerant such as R22 or R407C, which contains chlorine, will
deteriorate the refrigerating machine oil or cause the compressor to malfunction.
2 Evacuation
Evacuate with the ball valve of the heat source unit closed and evacuate both
the connection piping and the indoor unit from the service port provided on the
ball valve of the heat source unit using a vacuum pump. (Always evacuate from
the service port of both the high press pipe and the low press pipe.) After the
vacuum reaches 650 Pa [abs], continue evacuation for at least one hour or
more.
* Never perform air purging using refrigerant.
3 Refrigerant Charging
Since the refrigerant used with the unit is nonazerotropic, it must be charged in
the liquid state. Consequently, when charging the unit with refrigerant from a
cylinder, if the cylinder does not have a syphon pipe, charge the liquid refrigerant by turning the cylinder upside-down as shown in Fig.9.3.3. If the cylinder
has a syphon pipe like that shown in the picture on the right, the liquid refrigerant can be charged with the cylinder standing upright. Therefore, give careful
attention to the cylinder specifications. If the unit should be charged with gas
refrigerant, replace all the refrigerant with new refrigerant. Do not use the refrigerant remaining in the cylinder.
[Fig. 9.3.3] (P.5)
A
Syphon pipe
B
In case of the cylinder having no syphon pipe.
TR
RU
GR
[Fig. 9.3.2] (P.5)
A
System analyzer
Lo knob
C
Hi knob
D
Ball valve (Heat exchanger unit side)
B
E
Liquid pipe
F
Gas pipe
G
Service port
H
Three-way joint
I
Valve
J
Valve
K
R410A cylinder
L
Scale
M
Vacuum pump
N
To indoor unit
O
Heat source unit
Note:
• Always add an appropriate amount of refrigerant. Also always seal the
system with liquid refrigerant. Too much or too little refrigerant will cause
trouble.
• Use a gauge manifold, charging hose, and other parts for the refrigerant
indicated on the unit.
• Use a graviometer. (One that can measure down to 0.1 kg.)
• Use a vacuum pump with a reverse flow check valve.
(Recommended vacuum gauge: ROBINAIR 14830A Thermistor Vacuum
Gauge)
Also use a vacuum gauge that reaches 65 Pa [abs] or below after operating for five minutes.
9.4. Thermal insulation of refrigerant piping
Be sure to give insulation work to refrigerant piping by covering high press. (liquid)
pipe and low press. (gas) pipe separately with enough thickness heat-resistant
polyethylene, so that no gap is observed in the joint between indoor unit and insulating material, and insulating materials themselves. When insulation work is insufficient, there is a possibility of condensation drip, etc. Pay special attention to insulation work to ceiling plenum.
[Fig. 9.4.1] (P.5)
A
Steel wire
B
Piping
C
Asphaltic oily mastic or asphalt
D
Heat insulation material A
E
Outer covering B
Heat
insulation
material A
Glass fiber + Steel wire
Adhesive + Heat - resistant polyethylene foam + Adhesive tape
Indoor
Vinyl tape
Outer
Floor exposed Water-proof hemp cloth + Bronze asphalt
covering B
Heat source
Water-proof hemp cloth + Zinc plate + Oily paint
Note:
• When using polyethylene cover as covering material, asphalt roofing shall
not be required.
• No heat insulation must be provided for electric wires.
14
[Fig. 9.4.2] (P.5)
A
Liquid pipe
B
Gas pipe
D
Finishing tape
E
Insulator
C
Electric wire
When filling a gap with mortar, cover the penetration part with steel plate so that
the insulation material will not be caved in. For this part, use incombustible materials for both insulation and covering. (Vinyl covering should not be used.)
•
[Fig. 9.4.3] (P.5)
Insulation materials for the pipes to be added on site must meet the following
specifications:
Penetrations
[Fig. 9.4.4] (P.5)
<A> Inner wall (concealed)
<B> Outer wall
<C> Outer wall (exposed)
<D> Floor (waterproofing)
<E> Roof pipe shaft
Thickness
Temperature Resistance
*
Installation of pipes in a high-temperature high-humidity environment, such as
the top floor of a building, may require the use of insulation materials thicker
than the ones specified in the chart above.
*
When certain specifications presented by the client must be met, ensure that
they also meet the specifications on the chart above.
<F> Penetrating portion on fire limit and boundary wall
A
Sleeve
B
Heat insulating material
C
Lagging
D
Caulking material
E
Band
F
Waterproofing laye
G
Sleeve with edge
H
Lagging material
I
Mortar or other incombustible caulking
J
Incombustible heat insulation material
Pipe size
ø6.35 ~ 25.4 mm
ø28.58 ~ 38.1 mm
10 mm min.
15 mm min.
100 °C min.
7 Only the transmission line specified should be connected to the terminal block
for heat source unit transmission.
(Transmission line to be connected with indoor unit : Terminal block TB3 for
transmission line, Other : Terminal block TB7 for centralized control)
Erroneous connection does not allow the system to operate.
8 In the case of connecting with an upper class controller or to conduct group
operation in different refrigerant systems, the control line for transmission is
required between the heat source units.
Connect this control line between the terminal blocks for centralized control.
(2-wire line with no polarity)
When conducting group operation in different refrigerant systems without connecting to the upper class controller, replace the insertion of the short circuit
connector from CN41 of one heat source unit to CN40.
9 Group is set by operating the remote controller.
10.2. Control box and connecting position of
wiring
<Wiring compressor unit, Indoor unit>
1. The controller box for the indoor unit wiring is on the compressor unit.
2. Connect the indoor unit transmission line to transmission terminal block (TB3),
or connect the wiring between heat source units or the wiring with the central
control system to the central control terminal block (TB7).
When using shielded wiring, connect shield ground of the indoor unit transmission line to the earth screw ( ) and connect shield ground of the line between
heat source units and the central control system transmission line to the shield
(S) terminal of the central control terminal block (TB7) shield (S) terminal. In
addition, in the case of heat source units whose power supply connector CN41
has been replaced by CN40, the shield terminal (S) of terminal block (TB7) of
the central control system should also be connected to the earth screw ( ).
Fix the wiring securely in place with the cable strap at the bottom of the terminal block so that the external force if not applied to the terminal block. External
force applied to the terminal block may damage the block and short-circuit,
ground fault, or fire may result.
Power source
C
Earth screw
B
Transmission line
D
F
2. The top service panel can be removed by removing the three screws at the
top, tilting the panel by pulling the top of it away from the unit body, and pulling
it up.
3. The bottom service panel can be removed by first removing the top service
panel, then removing the 3 screws at the top, tilting the panel by pulling the top
of it away from the unit body, and pulling it up.
4. Wire the units as shown in the figure below.
Run the power supply line [0.75 mm2] and control line [0.3 mm2] separately
and at least 5 cm away from each other.
Keep them out of contact with the pipes.
Connect the heat exchanger unit and the compressor unit via 3 of the 4 connectors on each unit.
[Fig. 10.2.2] (P.6)
A
Heat exchanger unit
B
Compressor unit
C
Cable clamp (power supply line)
D
Cable clamp (control line)
E
Control cable
F
Power supply cable
<A> Enlarged view of connector section
<B> Heat exchanger unit side
<C> Compressor unit side
<D> CN102B (For power supply line)
<E> CN103B (For control line)
<F> CN101B (For power supply line)
<G>CN102A (For power supply line)
<H> CN103A (For control line)
<I> CN101A (For power supply line)
<J> CN104B (For control line)
<K> CN104A (For control line)
5. The length of standard equipped wiring, not including the heat exchanger unit’s
and the compressor unit’s internal wiring, is approximately 1.5 m.
If longer wiring is required, use optional extension wire for water heat source
(Available in 5 m and 10 m, not including the unit’s internal wiring).
6. Clamp excess power supply line [0.75 mm2] and control line [0.3 mm2] separately with the cable clamps on the compressor unit’s side panel.
Choose the appropriate size cable clamps for the amount of excess wiring.
[Fig. 10.2.3] (P.6)
<A> Compressor unit
[Fig. 10.2.1] (P.6)
A
1. Connect the connectors on the compressor unit and the heat exchanger unit
using the wires installed on the compressor unit (External heater adapter).
E
6 Use 2-core shield cable for transmission line. If transmission lines of different
systems are wired with the same multiplecore cable, the resultant poor transmitting and receiving will cause erroneous operations.
<Heat exchanger unit – compressor unit connection>
I
5 Never connect the main power source to terminal block of transmission line. If
connected, electrical parts will be burnt out.
NL
4 Give some allowance to wiring for electrical part box of indoor and heat source
units, because the box is sometimes removed at the time of service work.
6. Use the terminal block for pump interlock (TB8) when interlocking the unit with
the pump in the water circuit.
In this case, be sure to remove the short circuit wire on the terminal block for
pump interlocking (TB8).
Run the cable to TB8 via the same route as the power supply line.
P
3 Be sure to provide designated grounding work to heat source unit.
5. Narrow the opening by using a conduit to keep small animals out.
GR
2 Wiring for control (hereinafter referred to as transmission line) shall be (5 cm or
more) apart from power source wiring so that it is not influenced by electric
noise from power source wiring. (Do not insert transmission line and power
source wire in the same conduit.)
4. Fix power source wiring to terminal box by using buffer bushing for tensile
force (PG connection or the like).
RU
1 Follow ordinance of your governmental organization for technical standard related to electrical equipment, wiring regulations and guidance of each electric
power company.
3. Conduit mounting plates (ø27) are being provided. Pass the power supply and
transmission wires through the appropriate knock-out holes, then remove the
knock-out piece from the bottom of the terminal box and connect the wires.
A
Cable clamp for power supply cable
B
Cable clamp for control cable
15
TR
10.1. Caution
GB
10. Wiring
2. Remote control cables
7. Heat exchanger unit – compressor unit connected cable.
Cable name
Kind of control cable
Cable diameter
Maximum wiring length
Remarks
•
Cable 1
Cable 2
Cable 3
Cable 4 *1
8 core cable 12 core cable 12 core cable 6 core cable
(unshielded) (unshielded) (unshielded) (unshielded)
VCT *2
VCT *2
VCTF *3
VCTF *3
0.75 mm2
0.75 mm2
0.3 mm2
10 m
0.3 mm2
Remarks
•
Put the cable that connects the heat source units
through a conduit tube. Connect both ends of the conduit tube to the unit’s casing. Do not put cable 1 and
cable 2 through the same conduit tube with cable 3
and cable 4.
•
GB
1. Wiring transmission cables
*1 A transmission booster (RP) may be required depending on the number of
connected indoor unit controllers.
Types of transmission cables: Shielding wire CVVS or CPEVS or MVVS
2
•
Cable diameter: More than 1.25 mm
•
Maximum wiring length: Within 200 m
•
Maximum length of transmission lines for centralized control and indoor/outdoor transmission lines (Maximum length via indoor units): 500 m MAX
Controller name, symbol and allowable number of controllers.
Symbol
Name
Allowable number of controllers
Heat source unit controller
OC
Transmission booster unit
RP
Zero or one unit for one OC (*1)
Two to twenty four controllers for one OC (*1)
Indoor Unit Controller
IC
Maximum of two per group
Remote Controller
RC
1 Types of control cables
D
MA Remote Controller
2 Wiring examples
10.3. Wiring transmission cables
F
Sheathed 2-core cable (unshielded)
0.3 to 1.25 mm2 (0.75 to 1.25 mm2)*
When 10 m is exceeded, use cable with the
same specifications as 1. Wiring transmission
cables.
Kind of remote control cable Sheathed 2-core cable (unshielded) CVV
0.3 to 1.25 mm2 (0.75 to 1.25 mm2)*
Cable diameter
Within 200 m
Remarks
* Connected with simple remote controller.
*1 : PQHY-P400, 500 type only
*2 : VCT cable is not be lighter than design 245 IEC57.
*3 : VCTF cable is not be lighter than design 245 IEC53.
•
M-NET Remote Controller
Kind of remote control cable
Cable diameter
The maximum length of the wiring between power supply unit for transmission
lines (on the transmission lines for centralized control) and each outdoor unit
and system controller is 200 m.
Example of a group operation system with multiple heat source units (Shielding wires and address setting are
necessary.)
<Examples of transmission cable wiring>
E
[Fig. 10.3.1] M-NET Remote Controller (P.7)
[Fig. 10.3.2] MA Remote Controller (P.7)
[Fig. 10.3.3] Transmission booster unit (P.7)
<A> Change the jumper connector from CN41 to CN40.
<B> SW2-1:ON
I
<C> Keep the jumper connector on CN41.
A
Group 1
B
Group 3
C Group 5
D
Shielded wire
E
Sub remote controller
( ): Address
NL
<Wiring Method and Address Settings>
a. Always use shielded wire when making connections between the heat source unit (OC) and the indoor unit (IC), as well for all OC-OC, and IC-IC wiring intervals.
P
b. Use feed wiring to connect terminals M1 and M2 and the earth terminal on the transmission cable terminal block (TB3) of each heat source unit (OC) to terminals M1,
M2 and terminal S on the transmission cable block of the indoor unit (IC).
c. Connect terminals 1 (M1) and 2 (M2) on the transmission cable terminal block of the indoor unit (IC) that has the most recent address within the same group to the
terminal block on the remote controller (RC).
d. Connect together terminals M1, M2 and terminal S on the terminal block for central control (TB7) for the heat source unit (OC).
e. On one heat source unit only, change the jumper connector on the control panel from CN41 to CN40.
GR
f.
Connect the terminal S on the terminal block for central control (TB7) for the heat source unit (OC) for the unit into which the jumper connector was inserted into CN40
in the electrical component box.
in Step above to the earth terminal
g. Set the address setting switch as follows.
* To set the outdoor unit address to 100, the outdoor address setting switch must be set to 50.
TR
RU
Unit
IC (Main)
Range
01 to 50
IC (Sub)
01 to 50
Heat source Unit
M-NET R/C (Main)
M-NET R/C (Sub)
MA R/C
51 to 100
101 to 150
151 to 200
–
Setting Method
Use the most recent address within the same group of indoor units.
Use an address, other than that of the IC (Main) from among the units within the same group of indoor units. This must be
in sequence with the IC (Main)
Use the most recent address of all the indoor units plus 50
Set at an IC (Main) address within the same group plus 100
Set at an IC (Main) address within the same group plus 150
Unnecessary address setting (Necessary main/sub setting)
h. The group setting operations among the multiple indoor units is done by the remote controller (RC) after the electrical power has been turned on.
16
<Permissible Lengths>
1 M-NET Remote controller
•
Max length via outdoor units: L1 + L2 + L3 + L4 and L1 + L2 + L3 + L5 and L1 + L2 + L6 = 500 m (1.25 mm2 or more)
•
Max transmission cable length: L1 and L3 + L4 and L3 + L5 and L6 and L2 + L6 = 200 m (1.25 mm2 or more)
•
Remote controller cable length: r1, r2, r3, r4 = 10 m (0.3 to 1.25 mm2)
If the length exceeds 10 m, use a 1.25 mm2 shielded wire. The length of this section (L8) should be included in the calculation of the
maximum length and overall length.
2 MA Remote controller
•
Max length via outdoor unit (M-NET cable): L1 + L2 + L3 + L4 and L1 + L2 + L6 = 500 m (1.25 mm2 or more)
•
Max transmission cable length (M-NET cable): L1 and L3 + L4 and L6 and L2 + L6 = 200 m (1.25 mm2 or more)
•
Remote controller cable length: c1 and c1 + c2 + c3 and c1 + c2 + c3 + c4 = 200 m (0.3 to 1.25 mm2)
3 Transmission booster
•
Max transmission cable length (M-NET cable): 1 L1 + L2 + L3 + L5 + L6 = 200 m (1.25 mm2)
2 L1 + L2 + L3 + L5 + L7 = 200 m (1.25 mm2)
3 L1 + L2 + L4 = 200 m (1.25 mm2)
•
Remote controller cable length: r1, r2 = 10 m (0.3 to 1.25 mm2)
If the length exceeds 10 m, use 1.25 mm2 shielded cable and calculate the length of that portion (L4 and L7) as within the total extended
length and the longest remote length.
GB
4 L6 + L5 + L3 + L4, L4 + L3 + L5 + L7 = 200 m (1.25 mm2)
10.4. Wiring of main power supply and equipment capacity
Schematic Drawing of Wiring (Example)
A
Switch (breakers for wiring and current leakage)
B
Breakers for current leakage
D
Pull box
E
Indoor unit
C
D
[Fig. 10.4.1] (P.7)
Heat source unit
1. Use a separate power supply for the heat source unit and indoor unit.
2. Bear in mind ambient conditions (ambient temperature,direct sunlight, rain water,etc.) when proceeding with the wiring and connections.
3. The wire size is the minimum value for metal conduit wiring. The power cord size should be 1 rank thicker consideration of voltage drops.
Make sure the power-supply voltage does not drop more than 10 %.
4. Specific wiring requirements should adhere to the wiring regulations of the region.
5. Power supply cords of parts of appliances for heat source use shall not be lighter than polychloroprene sheathed flexible cord (design 245 IEC57). For
example, use wiring such as YZW.
6. A switch with at least 3.5 mm contact separation in each pole shall be provided by the Air conditioner installation.
7. This device is intended for the connection to a power supply system with a maximum permissible system impedance shown in the above table at the
interface point (power service box) of the user's supply.
The user has to ensure that this device is connected only to a power supply system which fulfills the requirement above.
If necessary the user can the ash the public power supply company for the system impedance at the interface point.
Warning:
•
•
Be sure to use specified wires to connect so that no external force is imparted to terminal connections. If connections are not fixed firmly, it may cause
heating or fire.
Be sure to use the appropriate type of overcurrent protection switch. Note that generated overcurrent may include some amount of direct current.
Caution:
E
RU
A breaker for current leakage must be attached to the power supply. If no earth leakage breaker is installed, it may cause an electric shock.
Do not use anything other than breaker and fuse with correct capacity. Using fuse and wire or copper wire with too large capacity may cause a malfunction
of unit or fire.
TR
•
•
I
Max. Permissive
System Impedance
60 A 100 mA 0.1sec. or less
0.32 Ω
60 A 100 mA 0.1sec. or less
0.23 Ω
20 A 30 mA 0.1sec. or less (apply to EN61000-3-3)
30 A 30 mA 0.1sec. or less (apply to EN61000-3-3)
40 A 30 mA 0.1sec. or less (apply to EN61000-3-3)
Breaker for current leakage
NL
Breaker for
wiring (NFB)
60
60
20
30
40
P
Switch (A)
Capacity
Fuse
63
63
63
63
16
16
25
25
32
32
GR
Minimum wire thickness (mm2)
Main cable
Branch
Ground
P400
10.0
10.0
10.0
Heat source
P500
10.0
10.0
10.0
16 A or less
1.5
1.5
1.5
Total operating current
25 A or less
2.5
2.5
2.5
of the indoor unit
32 A or less
4.0
4.0
4.0
F
Thickness of wire for main power supply, On/Off capacities and system impedance
17
11. Test run
F
D
GB
11.1. The following phenomena do not represent trouble (emergency)
Phenomenon
Indoor unit and BC controller generate sound
at the cooling/heating change over sometime.
Indoor unit does not perform cooling (heating) operation.
Display of remote controller
Normal display
Cause
This is not a trouble as it is just a selecting sound.
“Cooling (heating)” flashes
The auto vane runs freely.
Normal display
Fan setting changes during heating.
Normal display
Fan stops during heating operation.
Fan does not stop while operation has been
stopped.
No setting of fan while start SW has been
turned on.
Defrost display
No lighting
When multiple indoor units (max. 3) are connected to the same branch of the BC
controller, the heating (cooling) operation cannot be performed while another
indoor unit is performing a cooling (heating) operation.
Because of the control operation of auto vane, it may change over to horizontal
blow automatically from the downward blow in cooling in case the downward
blow operation has been continued for 1 hour. At defrosting in heating, hot adjusting and thermostat OFF, it automatically changes over to horizontal blow.
Ultra-low speed operation is commenced at thermostat OFF.
Light air automatically changes over to set value by time or piping temperature at
thermostat ON.
The fan is to stop during defrosting.
Fan is to run for 1 minute after stopping to exhaust residual heat (only in heating).
Indoor unit remote controller shows “HO” or
“PLEASE WAIT” indicator for about five minutes when turning ON universal power supply.
Drain pump does not stop while unit has been
stopped.
Drain pump continues to operate while unit
has been stopped.
“HO” or “PLEASE WAIT” flashes
Heat ready
Light out
Ultra low-speed operation for 5 minutes after SW ON or until piping temperature
becomes 35°C, low speed operation for 2 minutes thereafter, and then set notch
is commenced. (Hot adjust control)
System is being driven.
Operate remote controller again after “HO” or “PLEASE WAIT” disappear.
After a stop of cooling operation, unit continues to operate drain pump for three
minutes and then stops it.
Unit continues to operate drain pump if drainage is generated, even during a
stop.
kg
PQHY-P400YGM-A
–
kg
244
Model
Refrigerant (R410A)
Allowable pressure (Ps)
Net weight
PQHY-P500YGM-A
–
HP: 4.15 MPa, LP: 2.21 MPa
248
MANUFACTURER: MITSUBISHI ELECTRIC CORPORATION AIR-CONDITIONING & REFRIGERATION SYSTEMS
WORKS 5-66, TEBIRA, 6-CHOME, WAKAYAMA CITY, JAPAN
TR
RU
GR
P
NL
I
E
12. Information on rating plate
18
PQY-P01YGM-A
12.0
208