Range Master Professional Deluxe 100 Dual Fuel User guide

Britain’s No.1 Range Cooker
USER GUIDE &
INSTALLATION INSTRUCTIONS
Professional Deluxe 90 Dual Fuel
RANGEMASTER COOKWARE
Our range cookers are well known for providing the
best possible cooking performance and years of
faithful service. However, a great cooker alone cannot
guarantee perfect results every time. The other vital
ingredients are of course enthusiasm and quality
cookware.
We offer cookware to work perfectly with all fuel types
manufactured by Rangemaster, including induction
hobs. You can be assured of functionality with style, as
well as the quality and meticulous attention to detail
you expect from the pioneers of range cooking.
Visit: www.rangemastercookshop.co.uk
FRUITY BAKED PUDDING
Serves 4–6
Ingredients
Method
•
•
•
•
•
•
1. Preheat the oven to 200 °C (for a conventional oven),
180 oC (for a fan oven) or gas mark 6.
•
•
•
•
•
•
•
Oil for greasing
100 g strawberries
100 g raspberries
100 g redcurrants
100 g blackberries
or a 400 g mixture of any soft
fruits
2 medium eggs
30 g caster sugar
80 ml skimmed milk
2 tsp vanilla extract
60 g plain flour (sifted)
1 tsp baking powder
Icing sugar to dust
2. Lightly grease a dish 26 cm wide x 4 cm deep.
3. Thickly slice any large strawberries and place them with the other fruits
into an ovenproof dish, deep enough so the berries are about 2 deep.
4. Whisk the eggs and caster sugar until pale and fluffy. Beat the milk and
vanilla extract into the mixture and then fold in the sifted flour and
baking powder.
5. Pour the cake mix over the fruit and bake on the centre shelf of the
oven for 15-20 minutes, or until the mixture is cooked through and
golden on the top.
6. Dust with icing sugar and serve immediately with cream or crème
fraiche.
ROAST LOIN OF PORK WITH PROSCIUTTO
& BAY LEAVES
Ingredients
Method
• 3 kg (6½ lb) skinned and
boned loin of pork
• 2 x 70 g packs prosciutto
• Grated zest of 2 lemons
• Bay leaves
• Salt and freshly ground
black pepper
1. Preheat the oven to 220 °C (for a conventional oven), 200 °C (for a fan
oven) or gas mark 7.
For the sauce:
• 1 tablespoons plain flour
• 4 tablespoons lemon
juice
• Chicken stock/water
2. Spread one of the packs of prosciutto over a chopping board; place
the pork on top with the outer (fat) part of the pork resting on the
prosciutto.
3. Sprinkle the lemon zest onto the inside of the meat and season well. Lay
the remaining prosciutto on top of the zest and roll up.
4. Secure the pork with string or silicone bands and thread bay leaves
under the string, covering the whole piece of pork. Put the meat on to
a trivet over a large roasting tin containing enough water to cover the
base.
5. Place into the oven and cook for 30 minutes. Reduce the heat to 180 °C
conventional oven/160 °C fan oven/gas 4 and continue roasting for a
further 25 minutes per 500 g. Should the prosciutto start becoming too
brown, cover with some foil.
6. When the pork is cooked, place onto a warm plate, cover with foil and
allow to rest for at least 20 minutes.
7. Spoon off most of the fat from the roasting tin and stir the flour into the
remaining. Gradually add the stock and lemon juice, adding more stock
until the desired consistency is reached and simmer for 5 minutes. Check
the seasoning, adding more pepper or lemon juice as necessary.
8. Remove the string or bands from the pork and carve into slices, serve
with the sauce.
Contents
1.
2.
3.
Before You Start...
1
6.
Troubleshooting
18
Important!
1
Installation and Maintenance
1
7.
Installation
20
Peculiar Smells
1
Dear Installer
20
If You Smell Gas
1
Safety Requirements and Regulations
20
Ventilation
1
Provision of Ventilation
20
Personal Safety
1
Location of Cooker
21
Cooker Care
2
Conversion
21
Cleaning
2
Positioning the Cooker
22
Moving the Cooker
22
Completing the Move
23
Cooker Overview
3
Hotplate Burners
3
Fitting the Stability Bracket or Chain
23
Wok Burner
4
The Wok Cradle
5
Repositioning the Cooker Following
Connection
24
The Griddle
5
Conversion to Another Gas
24
The Glide-out Grill
6
Levelling
24
The Ovens
6
Gas Connection
25
The Clock
9
Electrical Connection
26
Accessories
11
Final Checks
26
Main Oven Light
11
Final Fitting
27
Customer Care
27
Cooking Tips
12
Tips on Cooking with the Timer
12
General Oven Tips
12
4.
Cooking Table
13
5.
Cleaning Your Cooker
14
Essential Information
14
Hotplate Burners
14
The Griddle
15
Glide-out Grill
15
Control Panel and Doors
15
Ovens
16
The Tall Oven
16
Cleaning Table
17
Professional Deluxe 90 Dual Fuel
8.
9.
Conversion to LP Gas
Injectors
28
Tap Adjustment
28
Stick on Label
28
Pressure Testing
28
Circuit Diagram
29
10. Technical Data
i
28
30
U110153-03
ii
1. Before You Start...
If You Smell Gas
Your cooker should give you many years of trouble-free
cooking if installed and operated correctly. It is important
that you read this section before you start, particularly if you
have not used a dual fuel cooker before.
•
DO NOT turn electric switches on or off
•
DO NOT smoke
•
DO NOT use naked flames
•
DO turn off the gas at the meter or cylinder
•
DO open doors and windows to get rid of the gas
•
DO keep people away from the area affected
•
Call your gas supplier
If you are using natural gas in the UK, ring the National Grid
on: 0800 111 999.
Important!
This appliance is designed for domestic cooking
nn
only. Using it for any other purpose could invalidate
any warranty or liability claim. In particular, the
oven should NOT be used for heating the kitchen –
besides invalidating claims this wastes fuel and may
overheat the control knobs.
This appliance is for use in Great Britain and the
nn
Republic of Ireland. It is a Cat II2H3+ cooker and is
Ventilation
CAUTION: The use of a gas cooking appliance results
nn
in the production of heat and moisture in the room
set for G20 at 20 mbar. (A conversion kit for LPG is
available for the cooker.)
in which it is installed. Therefore, make sure that the
kitchen is well ventilated: keep natural ventilation
holes open or install a powered cookerhood that
vents outside. If you have several burners on, or use
the cooker for a long time, open a window or turn on
an extractor fan.
Installation and Maintenance
In the UK, the cooker must be installed by a Gas Safe
registered engineer. The electrical installation should be in
accordance with BS 7671. Otherwise, all installations must be
in accordance with the relevant instructions in this booklet,
with the relevant national and local regulations, and with the
local gas and electricity supply companies’ requirements.
Personal Safety
DO NOT modify this appliance.
nn
This appliance can be used by children aged from
nn
8 years and above and persons with reduced
Make sure that the gas supply is turned on and that the
cooker is wired in and switched on (the cooker needs
electricity).
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Set the clock to make sure that the oven is functional – see
the relevant section in this manual.
Only a qualified service engineer should service the cooker,
and only approved spare parts should be used.
Unless specified otherwise in this guide, always allow the
cooker to cool and then switch it off at the mains before
cleaning or carrying out any maintenance work.
WARNING: The appliance and its accessible parts
nn
become hot during use and will retain heat even
Peculiar Smells
after you have stopped cooking. Care should be
taken to avoid touching heating elements. Children
less than 8 years of age shall be kept away unless
continuously supervised.
When you first use your cooker it may give off an odour. This
should stop after use.
Before using for the first time, make sure that all packing
materials have been removed and then, to dispel
manufacturing odours, turn the ovens to 200 °C and run for at
least an hour.
CAUTION: A long term cooking process has to be
nn
supervised from time to time. A short term cooking
process has to be supervised continuously.
Danger of fire: DO NOT store items on the cooking
nn
surfaces.
Before using the grill for the first time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back, and the grill door open.
To avoid overheating, DO NOT install the cooker
nn
behind a decorative door.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
Accessible parts will become hot during use and will
nn
retain heat even after you have stopped cooking.
Keep babies and children away from the cooker and
never wear loose-fitting or hanging clothes when
using the appliance.
DO NOT use a steam cleaner on your cooker.
nn
1
Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or medium high
temperatures. Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
Always be certain that the controls are in the OFF position
when the oven is not in use, and before attempting to clean
the cooker.
When the oven is on, DO NOT leave the oven door
nn
open for longer than necessary, otherwise the
control knobs may become very hot.
Do not use the top of the flue (the slots along the back of
the cooker) for warming plates, dishes, drying tea towels or
softening butter.
When using the grill, make sure that the grill pan
nn
is in position and pushed fully in, otherwise the
control knobs may become very hot.
DO NOT use water on grease fires and never pick
nn
up a flaming pan. Turn the controls off and then
Note that this appliance has a cooling fan. When an
oven or the grill is in operation the fan will run to
cool the fascia and control knobs.
nn
smother a flaming pan on a surface unit by covering
the pan completely with a well fitting lid or baking
tray. If available, use a multi-purpose dry chemical
or foam-type fire extinguisher.
DO NOT use harsh abrasive cleaners or sharp metal
nn
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Cooking high moisture content foods
can create a ‘steam burst’ when the oven
door is opened. When opening the oven
stand well back and allow any steam to
disperse.
Always keep combustible materials, e.g. curtains, and
flammable liquids a safe distance away from your cooker.
DO NOT spray aerosols in the vicinity of the cooker
nn
while it is on.
Take care that no water seeps into the
appliance.
Use dry oven gloves when applicable – using damp gloves
might result in steam burns when you touch a hot surface.
Do not use a towel or other bulky cloth in place of a glove – it
might catch fire if brought into contact with a hot surface.
ArtNo.324-0001 Steam burst
This appliance is heavy so take care when moving it.
nn
The appliance is not intended to be operated by
nn
means of external timer or separated remote-control
NEVER operate the cooker with wet hands.
nn
DO NOT use aluminium foil to cover shelves, linings
nn
or the oven roof.
system.
Cooker Care
DO NOT use hotplate protectors, foil or hotplate
nn
covers of any description. These may affect the safe
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours.
use of your hotplate burners and are potentially
hazardous to health.
NEVER heat unopened food containers. Pressure
nn
build up may make the containers burst and cause
injury.
Cleaning
DO NOT use unstable saucepans. Always make sure
nn
that you position the handles away from the edge of
In the interests of hygiene and safety, the cooker should be
kept clean at all times as a build up in fats and other food
stuff could result in a fire.
the hotplate.
DO NOT use cooking vessels on the hotplate that
nn
overlap the edges.
Clean only the parts listed in this guide.
Clean with caution. If a wet sponge or cloth is used to wipe
spills on a hot surface, be careful to avoid steam burns. Some
cleaners can produce noxious fumes if applied to a hot
surface.
Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on fire. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.
WARNING!
nn
Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
NEVER leave a chip pan unattended. Always heat fat
nn
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
2
2. Cooker Overview
A
Fig.2-1
Professional
B
deluxe
C
E
D
The 90 dual fuel cooker (Fig.2-1) has the following features:
A.
B.
C.
D.
E.
Fig.2-2
5 hotplate burners including a wok burner
A control panel
A glide-out grill
Main multi-function oven
Tall fan oven
Hotplate Burners
The drawing by each of the control knobs indicates which
burner that knob controls.
Each burner has a Flame Supervision Device (FSD) that
prevents the flow of gas if the flame goes out.
When a hotplate control knob is pressed in, sparks will be
made at every burner – this is normal. Do not attempt to
disassemble or clean around any burner while another
burner is on, otherwise an electric shock could result.
To light a burner, push in and turn the associated control
knob to the high position as indicated by the large flame
symbol (), (Fig.2-2).
The igniter should spark and light the gas. Keep holding the
knob pressed in to let the gas through to the burner for about
ten seconds.
3
Fig.2-3
If, when you let go of the control knob, the burner goes out,
then the FSD has not been bypassed. Turn the control knob
to the OFF position and wait for one minute before you try
again, this time making sure to hold in the control knob for
slightly longer.
ArtNo.270-0003
Proplus control to low
Adjust the flame height to suit by turning the knob counterclockwise (Fig.2-3). On this cooker the low position is beyond
high, NOT between high and off.
If a burner flame goes out, turn off the control knob and
leave it for one minute before relighting it.
Make sure that the flames are under the pans. Using a lid will
help the contents boil more quickly (Fig.2-4).
Fig.2-4
Large pans should be spaced well apart.
Pans and kettles with concave bases or down-turned base
rims should not be used (Fig.2-5).
Simmering aids, such as asbestos or mesh mats, are
NOT recommended (Fig.2-6). They will reduce burner
performance and could damage the pan supports.
ArtNo.311-0001 Right pans gas
You should also avoid using unstable and misshapen pans
that may tilt easily, and pans with a very small base diameter,
e.g. milk pans, single egg poachers (Fig.2-7).
Fig.2-5
The minimum recommended pan diameter is 120 mm. The
maximum allowable pan base diameter is 260 mm.
ArtNo.311-0002 Pan with rim
DO NOT use cooking vessels on the hotplate that overlap the
edges.
Wok Burner
The wok burner is designed to provide even heat over a large
area. It is ideal for large pans and stir-frying (Fig.2-8).
Fig.2-6
For heating smaller pans, the aforementioned hotplate
burners may be more efficient.
You can remove the burner parts for cleaning; see ‘Cleaning
Your Cooker’.
Art No. 311-0003 Simmer aids
You should wipe the enamel top surface of the cooker around
the hotplate burners as soon as possible after spills occur. Try
to wipe them off while the enamel is still warm.
Fig.2-7
Note: The use of aluminium pans may cause metallic marking
of the pan supports. This does not affect the durability of the
enamel and may be cleaned off with an appropriate metal
cleaner.
ArtNo.311-0004 Tipping wok
Fig.2-8
4
The Wok Cradle
Fig.2-9
The wok cradle is designed to fit a 35 cm wok. If you use a
different wok, make sure that it fits the cradle. Woks vary very
widely in size and shape. It is important that the wok sits
down on the pan support – however, if the wok is too small,
the cradle will not support it properly (Fig.2-9).
The cradle should be used on the wok burner only. When you
fit the cradle, make sure that it is supported properly on a pan
support and the wok is sitting level in the cradle (Fig.2-10).
ArtNo.311-0006 Correct wok sizes
The cradle will get very hot in use – allow plenty of time for it
to cool before you pick it up.
Fig.2-10
The Griddle
The griddle fits a single pan support, front to back (Fig.2-11).
It is designed for cooking food on directly. DO NOT use pans
of any kind on it. The griddle surface is non-stick and metal
cooking utensils (e.g. spatulas) will damage the surface. Use
heat resistant plastic or wooden utensils.
ArtNo.311-0007 Wok stand close-up
DO NOT put it crossways – it will not fit properly and
nn
will be unstable (Fig.2-12).
DO NOT put it on any other burner – it is not
nn
designed to fit in any of the other pan supports.
Position the griddle over the hotplate burners resting on the
pan support. Check that it is securely located.
The griddle can be lightly brushed with cooking oil before
use (Fig.2-13). Light the hotplate burners. Adjust the flame
heights to suit.
Fig.2-11
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. Turn the
control knob towards the low position, marked with the small
flame symbol, to reduce the burner flames.
Always leave space around the griddle for the gases
nn
to escape.
NEVER fit two griddles side by side (Fig.2-14).
nn
After cooking, allow the griddle to cool before cleaning.
Fig.2-12
ArtNo.311-0009 Oil on griddle
Fig.2-13
Fig.2-14
ArtNo.311-0008 Griddle positioning
5
The Glide-out Grill
Fig.2-15
Open the door and pull the grill pan carriage forward using
the handle (Fig.2-15).
The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.
Adjust the heat to suit by turning the knob. To heat the whole
grill, turn the knob clockwise (Fig.2-16).
To heat the right-hand half, turn the knob counter-clockwise.
The neon indicator light by the grill control will come on.
ArtNo.331-0001Grill pan pulled forwards
Fig.2-16
For best results, slide the carriage back into the grill chamber
and preheat the appropriate part(s) of the grill for two
minutes. The grill trivet can be removed and the food placed
on it while you are waiting for the grill to preheat.
ArtNo.270-0004
Proplus grill control
0
1
DO NOT leave the grill on for more than a few
nn
moments without the grill pan underneath it,
otherwise the knobs may become hot.
2
2
1
Once the grill has preheated, slide the carriage out again.
With the trivet back in place with the food on it, slide the
carriage back into the grill chamber. Make sure that it is
pushed right in.
3
3
Accessible parts may be hot when the grill is in use.
nn
Young children should be kept away.
Fig.2-17
The grill pan trivet can be turned over to give two grilling
positions (Fig.2-17).
Do not leave the grill on for more than a few moments,
without the grill pan underneath it.
ArtNo.331-0002 Grill pan high/low position
Never close the grill door when the grill is on.
nn
The Ovens
Function
Use
Defrost
To thaw small items in the oven without
heat
Fan oven
A full cooking function, even heat
throughout, great for baking
Fanned grilling
Grilling meat and fish with the door
closed
Fan assisted
A full cooking function good for roasting
and baking
The clock must be set to the time of day before the ovens
will work. See the following section on ‘The Clock’ for
instructions on setting the time of day.
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.
The left-hand oven is a programmable multi-function oven,
while the right-hand tall oven is a fan oven.
The Multi-function Oven
A full cooking function for roasting and
Conventional oven
baking in the lower half of the oven
Browning element
To brown and crisp cheese topped
dishes
Base heat
To crisp up the bases of quiche, pizza or
pastry
As well as the oven fan and fan element, they are fitted
with two extra heating elements, one visible in the top of
the oven and the second under the oven base. Take care to
avoid touching the top element and element deflector when
placing or removing items from the ovens.
The multi-function oven has 3 main cooking functions, fan,
fan assisted and conventional cooking. These functions
should be used to complete most of your cooking.
Table 2-1
The browning element and base heat can be used in the
latter part of the cooking process to fine tune the results to
your particular requirements.
Use fanned grilling for all your grilling needs and defrost to
safely thaw small items of frozen food.
Table 2-1 gives a summary of the multi-function modes.
6
Fan Assisted Oven
The multi-function ovens have many varied uses. We suggest
you keep a careful eye on your cooking until you are familiar
with each function. Remember – not all functions will be
suitable for all food types.
This function operates the fan, circulating air heated
by the elements at the top and the base of the oven.
The combination of fan and conventional cooking
(top and base heat) makes this function ideal for cooking
large items that need thorough cooking, such as a large meat
roast.
Please remember that all cookers vary – temperatures in your
new ovens may differ to those in your previous cooker.
Multi-function Oven Functions
When using this function, it is also possible to bake on two
shelves at one time, although they will need to be swapped
over during the cooking time, as the heat at the top of the
oven is greater than at the base.
Rapid Response
The Rapid Response setting enables you to preheat
the oven faster than normal. It uses the fan oven
element with additional heat from one of the
elements in the top of the oven.
This is a fast intensive form of cooking; keep an eye on the
food cooking until you have become accustomed to this
function.
Fan ovens heat up quickly; but the Rapid Response feature
speeds this process up enabling you to start cooking sooner.
Conventional Oven (Top and Base Heat)
To use the Rapid Response feature, turn the function control
knob to R and set the temperature required. The light on the
control panel next to the function control will come on.
This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits.
When the required temperature is reached the top element
will switch off and the light will go out. The oven temperature
is then maintained by the fan oven element and fan.
Food cooked on the top shelf will brown and crisp faster than
on the lower shelf, because the heat is greater at the top of
the oven than at the base, as in ‘Fan Assisted Oven’ function.
Similar items being cooked will need to be swapped around
for even cooking. This means that foods requiring different
temperatures can be cooked together, using the cooler zone
in the lower half of the oven and hotter area to the top.
Should you choose to place food into the cold oven prior to
cooking while using the Rapid Response function, make sure
that cakes, etc. are not positioned too near the top of the
oven.
The exposed top element may cook some foods too quickly,
so we recommend that the food be positioned in the lower
half of the oven to cook. The oven temperature may also need
to be lowered.
Fan Oven
This function operates the fan and the heating
element around it. An even heat is produced
throughout the oven, allowing you to cook large
amounts quickly.
Browning Element
This function uses the element in the top of the oven
only. It is a useful function for the browning or
finishing of pasta dishes, vegetables in sauce,
shepherds pie and lasagne, the item to be browned being
already hot before switching to the top element.
Fan oven cooking is particularly suitable for baking on several
shelves at one time and is a good ‘all-round’ function. It may
be necessary to reduce the temperature by approximately
10 °C for recipes previously cooked in a conventional oven.
If you wish to preheat the oven, wait until the indicator light
has gone out before inserting the food.
Base Heat
This function uses the base element only. It will crisp
up your pizza or quiche base or finish off cooking the
base of a pastry case on a lower shelf. It is also a
gentle heat, good for slow cooking of casseroles in the
middle of the oven or for plate warming.
Fanned Grilling
This function operates the fan whilst the top element
is on. It produces a more even, less fierce heat than a
conventional grill. For best results, place the food to
be grilled, on a trivet over a roasting tin, which should be
smaller than a conventional grill pan. This allows greater air
circulation. Thick pieces of meat or fish are ideal for grilling in
this way, as the circulated air reduces the fierceness of the
heat from the grill.
The Browning and Base Heat functions are useful additions
to your oven, giving you flexibility to finish off items to
perfection.
Defrost
The oven door should be kept closed while grilling is in
progress, so saving energy.
This function operates the fan to circulate cold air
only. Make sure the temperature control is at 0°C and
that no heat is applied. This enables small items such
as desserts, cream cakes and pieces of meat, fish and poultry
to be defrosted.
You will also find that the food needs to be watched and
turned less than for normal grilling. Preheat this function
before cooking.
Defrosting in this way speeds up the process and protects
the food from flies. Pieces of meat, fish and poultry should
be placed on a rack, over a tray to catch any drips. Be sure to
For best results we recommend that the grill pan is not
located on the uppermost shelf.
7
wash the rack and tray after defrosting.
Fig.2-18
Defrost with the oven door closed.
Large items, such as whole chickens and joints should not be
defrosted in this way. We recommend this be carried out in a
refrigerator.
0
Defrosting should not be carried out in a warm oven or when
an adjoining oven is in use or still warm.
Make sure that dairy foods, meat and poultry are completely
defrosted before cooking.
The Fan Oven
Temperature control
Fig.2-19
Function control
The right-hand tall oven is a fan oven that circulates hot air
continuously, which means faster, more even cooking.
The recommended cooking temperatures for a fan oven are
generally lower than a conventional oven.
ArtNo.270-0005 Proplus
electric oven control
Note: Please remember that all cookers vary so temperatures
in your new ovens may differ to those in your previous
cooker.
0
Operating the Ovens
0
10
0
22
180
140
The multi-function oven has two controls: a function selector
and a temperature setting knob (Fig.2-18).
Turn the function selector control to a cooking function. Turn
the oven temperature knob to the temperature required
(Fig.2-19).
ArtNo.270-0006 Proplus
oven control light
140
The oven heating light will glow until the oven has reached
the temperature you selected. It will then cycle on and off
during cooking.
10
0
220
0
18
Operating the Fan Oven
Turn the oven knob to the desired temperature (Fig.2-19).
The oven indicator light will glow until the oven has reached
the temperature selected (Fig.2-20). It will then cycle on and
off during cooking.
0
Fig.2-20
Operating the Multi-function Oven
8
The Clock
ArtNo.300-0004 2-button clock annotated
You can use the clock to turn the left-hand oven on and off.
The clock must be set to the time of day before the oven
will work.
Fig.2-21
Note: When using the timer functions, first set the clock as
required before setting the oven temperature and selecting
the oven function.
Setting the Time of Day
A
The 2-button LCD clock is shown in (Fig.2-21). When the
clock is first connected, the display flashes ( 0.00 ) and (
)
alternately.

B
A – Timer knob, B – Adjusting knob
To set the time, turn and hold the Timer knob to the clock
symbol [] and at the same time turn the Adjusting knob left
or right until the clock shows the time of day. Remember this
is a 24-hour clock. Let go of the Timer knob and it will spring
back to the vertical, oven manual setting.
ArtNo.300-0005 2BC
minute minder setting
Fig.2-22
ArtNo.300-0006 2BC
minute minder setting 2
Fig.2-23
ArtNo.301-0007 2BC
Stopping the oven 1
Fig.2-24
ArtNo.301-0008 2BC
Stopping the oven 2
Fig.2-25
ArtNo.301-0009 2BC
Setting the cooking timer
Fig.2-26
ArtNo.301-0010 2BC
Setting the cooking time
Fig.2-27
IMPORTANT: The left-hand oven will not operate unless the
clock has been set.
Setting the Minute Minder
To activate the minute minder turn the Timer knob to the
right to the [] minute minder setting – it should click into
position (Fig.2-22).
Rotate the Adjusting knob to set the time required (Fig.2-23).
You can either turn the knob back to the vertical manual
setting [] to keep an eye on the time of day, or leave it in
the [] minute minder position as the time ticks down.
To stop the beeper when it sounds, turn the Adjusting knob
counter-clockwise.
•
•
The ‘cook period’, which is the length of time you
want the oven to cook for.
The ‘stop time’, which is the time of day you want the
oven to stop cooking.
To Stop the Oven at a Specific Time of Day
Turn the Timer knob to the [] position (Fig.2-24).
Use the Adjusting knob to set the ‘stop time’. You can set
the oven to turn on at any time over the following 24-hour
period. AUTO shows in the display (Fig.2-25).
Turn the Timer knob to the bottom ‘AUTO’ setting to return to
the clock display.
Once the ‘stop time’ is reached, the beeper sounds. Turn the
Timer knob to the vertical [] to return to manual cooking.
To Start and Then Stop the Oven Using the
Timer
You cannot set a start time directly – this is set
automatically by a combination of the ‘cook time’ and
‘stop time’.
Turn the Timer knob to the [] position (Fig.2-26).
Turn the Adjusting knob to set the ‘cooking time’ you need
(Fig.2-27).
9
Fig.2-28
Turn the Timer knob to the [] position. The display will
show the current time of day plus the ‘cook time’ you just set.
Use the Adjusting knob to set the ‘stop time’ required
(Fig.2-28).
ArtNo.301-0008 2BC
Stopping the oven 2
The ‘stop time’ is displayed, followed by ‘AUTO’. Set the oven
to the cooking temperature you need. Turn the Timer knob to
the ‘Auto’ setting.
Fig.2-29
When your cooking is finished, the beeper sounds. Turn the
Timer knob to the vertical [] to return to manual cooking.
Art No. 301-0011 2BC
Activating the key lock 1
If you are out, do not worry about the beeper going off – it
stops on its own after a while. When you return, turn the
Timer knob to the vertical [] to return to manual cooking.
AUTO is Showing, But You Want to Revert to
Manual Cooking
Fig.2-30
You can cancel any automatic settings by briefly turning the
Timer knob to the clock symbol [] and then releasing it.
ArtNo.301-0012 2BC
Activating the key lock 2
Key Lock
When the key lock is activated the left-hand oven is locked
and will not come on.
The right-hand oven can be operated as usual.
Fig.2-31
To activate the key lock
ArtNo.301-0013 2BC
Activating the key lock 3
Make sure that the clock is in manual mode and cancel
any active programs.
Turn and hold the Timer knob to the clock symbol [] for
about 8 seconds. ‘On’ appears on the display (Fig.2-29).
Fig.2-32
While still holding the Timer knob turned to the clock symbol
[], turn the Adjusting knob clockwise until the key symbol
[] and ‘OF’ shows on the display (Fig.2-30). Release the
knobs.
ArtNo.301-0014 2BC
Deactivating the key lock 1
The left-hand oven is now locked, as is confirmed by the
display showing the time of day alongside the key symbol []
(Fig.2-31).
To turn off the key lock
Fig.2-33
Turn and hold the Timer knob to the clock symbol [] for
about 8 seconds. ‘OF’ will appear on the display (Fig.2-32).
ArtNo.301-0015 2BC
Deactivating the key lock 2
While still holding the Timer knob turned to the clock symbol
[], turn the Adjusting knob clockwise until the key symbol
[] goes out on the display and ‘On’ shows (Fig.2-33). Let go
of the knobs.
After a few seconds, the display reverts to showing the time
of day.
The oven can now be used normally.
10
Accessories
Fig.2-34
Flat shelf
Oven Shelves – Left-hand (Main) Oven
In addition to the flat shelves, your cooker is supplied with a
drop shelf (Fig.2-34). The drop shelf increases the possibilities
for oven shelf spacing.
Shelf guard
Front
The oven shelves can be easily removed and refitted.
Pull the shelf forward until the back of the shelf is stopped by
the shelf stop bumps in the oven sides (Fig.2-35).
Shelf guard
Drop shelf
Lift up the front of the shelf so the back of the shelf will pass
under the shelf stop and then pull the shelf forward (Fig.2-36).
To refit the shelf, line up the shelf with a groove in the oven
side and push the shelf back until the ends hit the shelf stop.
Lift up the front so the shelf ends clear the shelf stops, and
then lower the front so that the shelf is level and push it fully
back (Fig.2-37).
Front
Fig.2-35
Fig.2-36
Oven Shelves – Right-hand (Tall) Oven
The tall oven is supplied with four flat cooking shelves
(Fig.2-38), and a plate-warming shelf (Fig.2-39).
ArtNo.320-0011 Removing the shelf 1
When using the tall oven, you can cook on all four shelves at
the same time, but make sure that they are well spaced out
allow the hot air to circulate.
Fig.2-37
ArtNo.320-0012 Removing the shelf 2
Fig.2-38
The Handyrack (Main Oven)
The Handyrack (Fig.2-40) fits to the left-hand oven door
only. Food cooking on it is easy to attend to, because it is
accessible when the door is open.
ArtNo.324-0002 Oven shelf
The maximum weight that can be held by the Handyrack
is 5.5 kg (12 lb). It should only be used with the supplied
roasting tin, which is designed to fit the Handyrack. Any other
vessel could be unstable.
ArtNo.320-0013 Removing the shelf 3
Fig.2-39
Fig.2-40
It can be fitted at two different heights. One of the oven
shelves must be removed and the other positioned to suit.
When the Handyrack is used in its highest position, other
dishes can be cooked on the bottom shelf position or base of
the oven.
ArtNo.324-0010 Plate warming shelf
ArtNo.320-0014 Handyrack on LH door
When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or base of
the oven.
Fig.2-41
Fig.2-42
To fit the Handyrack, locate one side of it on the door bracket
(Fig.2-41).
Then spring the other side out to clip it onto the other
bracket (Fig.2-42).
Main Oven Light
ArtNo.320-0015
Fitting the Handyack 1
ArtNo.320-0016
Fitting the handyrack 2
Press the button to turn the light on (Fig.2-43).
If the oven light fails, turn off the power supply before
changing the bulb. See the ‘Troubleshooting’ section for
details on how to change the bulb.
Fig.2-43
ArtNo.320-0017
Main oven light
11
3. Cooking Tips
Tips on Cooking with the Timer
General Oven Tips
If you want to cook more than one dish, choose dishes that
require approximately the same cooking time. However,
dishes can be ‘slowed down’ slightly by using small containers
and covering them with aluminium foil, or ‘speeded up’
slightly by cooking smaller quantities or placing them in
larger containers.
The wire shelves should always be pushed firmly to the back
of the oven.
Baking trays with food cooking on them should be placed
level with the front edge of the oven’s wire shelves. Other
containers should be placed centrally. Keep all trays and
containers away from the back of the oven, as overbrowning
of the food may occur.
Very perishable foods such as pork or fish should be avoided
if a long delay period is planned, especially in hot weather.
For even browning, the maximum recommended size of a
baking tray is 340 mm (13½”) by 340 mm (13½”) in the main
oven and 232 mm (91/8”) by 321 mm (125/8”) in the tall oven.
DO NOT place warm food in the oven to be timed.
nn
DO NOT use a timed oven that is already warm.
nn
DO NOT use the timed oven if the adjoining oven is
nn
already warm.
When the oven is on, do not leave the door open for
longer than necessary, otherwise the knobs may get very
hot.
Whole poultry must be thoroughly defrosted before being
placed in the oven. Check that meat and poultry are fully
cooked before serving.
•
•
•
•
•
•
12
Always leave a “finger’s width” between dishes on
the same shelf. This allows the heat to circulate freely
around them.
To reduce fat splashing when you add vegetables to hot
fat around a roast, dry them thoroughly or brush lightly
with cooking oil.
Where dishes may boil and spill over during cooking,
place them on a baking tray.
The ‘Cook & Clean’ oven liners (see ‘Cleaning Your
Cooker’) work better when fat splashes are avoided.
Cover meat when cooking with foil or use a roasting
bag.
Sufficient heat rises out of the oven while cooking to
warm plates in the grill compartment.
If you want to brown the base of a pastry dish, preheat
the baking tray for 15 minutes before placing the dish in
the centre of the tray.
4. Cooking Table
DocNo.031-0004 - Cooking table - electric & fan single cavity
The oven control settings and cooking times given in the table below are intended to be used
AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a
preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The
temperature in the fan oven does not vary with height in the oven so you can use any shelf.
Top (T)
Centre (C)
Base (B)
Oven Shelf Positions
Conventional Oven
Fan Oven
Temperature °C
Temperature
(Shelf Position)
°C
160 (C)
150
200 (C)
190
160 (C)
150
200 (C)
190
160 (C)
150
200 (C)
190
160 (C)
150
20-25 minutes per 500g +20-25 minutes.
200 (C)
190
15-20 minutes per 500g +15-20 minutes.
160 (C)
150
20 minutes per 500g +20 minutes.
200 (C)
190
15 minutes per 500g +15 minutes.
160 (C)
150
25-30 minutes per 500g.
200 (C)
190
20 minutes per 500g.
140-150 (C)
130-140
220 (C)
210
Large tins 30-35 minutes; individual 10-20 minutes.
140 (C/B)
130
45-50 minutes per 500g of mixture.
Fruit 180 mm tin
150 (C/B)
140
2-2½ hours.
Fruit 230 mm tin
150 (C/B)
140
Up to 3½ hours.
Madeira 180 mm
160 (C/B)
150
80-90 minutes.
Queen cakes
190 (C/B)
180
15-25 minutes.
Scones
220 (C/B)
210
10-15 minutes.
180 mm tin
180 (C/B)
170
20-30 minutes.
210 mm tin
180 (C/B)
170
30-40 minutes.
Shortcrust tarts
200 (C/B)
190
20-30 minutes on a preheated tray.
Fruit pies
200 (C/B)
190
35-45 minutes.
Tartlets
200 (C/B)
190
10-20 minutes according to size.
Puff pastry
210 (C/B)
200
20-40 minutes according to size.
Meringues
100 (C/B)
90
2-3 hours.
Food
Meat
ArtNo.050-0007
Oven shelf positions
T - Top; C - Centre; B - Base
Approximate Cooking Time
ArtNo.050-0001 Gas cooking table
Beef (no bone)
Lamb
Pork
Poultry
Chicken
Turkey
Duck
Casserole
Yorkshire Pudding
30-35 minutes per 500g +30-35 minutes. Thoroughly thaw frozen joints before
cooking. Meat may be roasted at
20-25 minutes per 500g +20-25 minutes.
220°C (210°C for fan oven) and the
30-35 minutes per 500g +30-35 minutes. cooking time adjusted accordingly.
25-30 minutes per 500g +25-30 minutes. For stuffed and rolled meats, add
approximately 10 minutes per 500g,
35-40 minutes per 500g +35-40 minutes. or cook at 200°C (190°C) for 20
25-30 minutes per 500g +25-30 minutes. minutes then 160°C (150°C) for the
remainder.
2-4 hours according to recipe.
For stuffed poultry, you could cook
at 200°C (190°C) for 20 minutes
then 160°C (150°C) for remainder.
Do not forget to include the weight
of the stuffing.
For fresh or frozen prepacked
poultry, follow instructions on the
pack. Thoroughly thaw frozen
poultry before cooking.
Cake
Very rich fruit - Christmas,
wedding, etc.
Using the conventional oven: when
two tier cooking leave at least one
runner space between shelves.
Position the baking tray with the
front edge along the front of the
oven shelf.
Victoria sandwich
Desserts
Baked egg custard
160 (C/B)
150
45-60 minutes.
Baked sponge pudding
180 (C/B)
170
40-45 minutes.
140-150 (C/B)
130-140
210 (C)
200
20-30 minutes.
Milk pudding
Bread
Fish
2 to 3 hours.
Fanned Grilling
Fillet
190 (C/B)
190 (C/B)
15-20 minutes.
Whole
190 (C/B)
190 (C/B)
15-20 minutes per 500g.
Steak
190 (C/B)
190 (C/B)
Steaks according to thickness.
13
Up to three tiers can be cooked in a
fan oven at the same time but make
sure to leave at least one runner
space between each shelf being
cooked on.
Using the conventional oven: for
even browning the maximum size of
baking tray recommended is 340 mm
x 340 mm. This ensures free heat
circulation.
If cooking a two tier load, the trays
should be interchanged
approximately halfway though the
cooking time.
5. Cleaning Your Cooker
Essential Information
Fig.5-1 A
Isolate the electricity supply before carrying out any
thorough cleaning. Allow the cooker to cool.
C
NEVER use paint solvents, washing soda, caustic
nn
cleaners, biological powders, bleach, chlorine based
B
bleach cleaners, coarse abrasives or salt.
DO NOT mix different cleaning products – they may
nn
react together with hazardous results.
E
D
All parts of the cooker can be cleaned with hot soapy water
– but take care that no surplus water seeps into the
appliance.
ArtNo.311-0032 Burner layout FSD
A – Cap, B – Head, C – Notch, D – Base, E – Electrode
Fig.5-2
Remember to switch on the electricity supply and reset the
clock before re-using the cooker.
A
Hotplate Burners
The burner heads and caps can be removed for cleaning.
B
DO NOT put the burner heads in a dishwasher.
nn
Make sure they are absolutely dry before replacing them.
C
The Single Ring Burners
When refitting the burner head, make sure that the notch
lines up with the electrode or hole in the base. Check that the
burner head is level and that the cap is fitted centrally on the
burner head (Fig.5-1).
D
ArtNo.311-0033 Wok burner details FSD
The Wok Burner
The wok burner can also be taken apart for cleaning.
E
When reassembling the wok burner (Fig.5-2), turn over the
large base ring and find the ‘D’ shaped area (Fig.5-3). Turn the
head until the ‘D’ matches the one on the burner base. Flip
the burner over once again and place it on the burner base.
A – Inner burner cap, B – Outer burner cap, C – Inner burner head,
D – Outer burner head, E – Wok burner base
To fit the small inner burner, find the larger electrode notch in
the burner rim. Line this up with the white ignition electrode
and place the inner burner on the large base ring (Fig.5-4).
Fig.5-3
Now fit the two burner caps, making sure that they are seated
properly.
Check the burner ports are not blocked. If a blockage occurs,
remove stubborn particles using a piece of fuse wire.
The Wok Cradle
Fig.5-4
Recommended cleaning materials are hot soapy water, a
moistened soap pad, cream cleaner or a nylon scourer.
B
A
ArtNo.311-0016 Fitting the burner inner head
A – Electrode notch, B – Ignition electrode
14
The Griddle
Fig.5-5
Always clean the griddle after use. Allow it to cool completely
before removing. Immerse the griddle plate in hot soapy
water. Use a soft cloth or, for stubborn stains, a nylon washing
up brush.
Note: If the griddle is washed in a dishwasher then some
dishwasher residue may appear on the back. This is normal
and will not affect the performance of your griddle.
Glide-out Grill
ArtNo.331-0001Grill pan pulled forwards
Before you remove any of the grill parts for cleaning.
nn
make sure that they are cool, or use oven gloves.
ArtNo.331-0003 Grill frame out, no pan
The grill pan and trivet should be washed in hot soapy water.
Alternatively, the grill pan can be washed in a dishwasher.
Fig.5-6
After grilling meats or any foods that soil, leave to soak for
a few minutes in the sink immediately after use. Stubborn
particles may be removed from the trivet by using a nylon
brush.
The grill pan can be easily removed for cleaning as follows:
Remove the grill pan support frame by pulling the grill pan
forward (Fig.5-5).
Lift the grill pan clear of the support frame. The support frame
is held to the side rails by two clips on each side (Fig.5-6).
Fig.5-7
For each side, support the side rail with one hand and with
the other hand lift the frame up and out of the side clips
(Fig.5-7).
For safety, push the side rails back into the grill chamber.
If you need to remove the side rails to allow cleaning of the
grill chamber, you can unhook them from the grill chamber
sides (Fig.5-8) and wipe the sides clean with a soft cloth and
mild detergent.
ArtNo.331-0004 Removing the grill frame
DO NOT put the side runners in a dishwasher.
Once you have finished, hook the side rails back onto the
sides of the chamber. To refit the frame, pull the side rails
forward and, for each side in turn, support the side rail and
press the frame down into the side rails.
Fig.5-8
Replace the grill pan. When refitting the grill pan, make sure
that the wide rim is at the front (Fig.5-9).
Control Panel and Doors
ArtNo.331-0005 Removing the grill rail
Avoid using any abrasive cleaners including cream cleaners.
For best results, use a liquid detergent.
The same cleaner can be used on the doors, or alternatively,
using a soft cloth wrung out in clean hot soapy water – but
take care that no surplus water seeps into the appliance.
Fig.5-9
After cleaning, polish with a dry cloth.
ArtNo.331-0006 Grill pan plan
15
Ovens
Fig.5-10
‘Cook & Clean’ Panels
The main oven has panels which have been coated with a
special enamel that partly cleans itself. This does not stop
all marks on the lining, but helps to reduce the amount of
manual cleaning needed.
The ‘Cook & Clean’ panels work better above 200 °C. If you do
most of your cooking below this temperature, occasionally
remove the panels and wipe with a lint free cloth and hot
soapy water. The panels should then be dried and replaced
and the oven heated at 200 °C for about one hour. This
will make sure that the ‘Cook & Clean’ panels are working
effectively.
Fig.5-11
DO NOT use steel wool, oven cleaning pads, or any other
materials that will scratch the surface.
Removing the Main Oven Linings
ArtNo.320-0022 Tall oven side support
Some of the lining panels can be removed for cleaning.
If you wish to clean the enamel interior of the oven, you
will need to remove the shelves before removing the ‘Cook
& Clean’ panels. You do not have to remove the support
brackets to remove the panels. Lift each panel upward and
slide forward off the support brackets (Fig.5-10).
Once the panels have been removed, the oven enamel
interior can be cleaned.
Refit in the reverse order.
The Tall Oven
To clean the oven sides, slide out the shelves, unhook the
supports from the oven sides, and lift out (Fig.5-11).
16
Cleaning Table
Cleaners listed (Table 5-1) are available from supermarkets or
electrical retailers as stated.
For enamelled surfaces use a cleaner that is approved for use
on vitreous enamel.
Regular cleaning is recommended. For easier cleaning, wipe
up any spillages immediately.
Hotplate
Part
Finish
Recommended Cleaning Method
Hob top (including burner heads and
Enamel or stainless steel
caps)
Hot soapy water, soft cloth. Any stubborn stains remove gently
with a nylon scourer.
Ceramic/Induction hob
Toughened glass
Hot soapy water; cream cleaner/scourer if necessary.
Griddle plate (some models only)
Non-stick surface
Allow to cool. Wash in hot soapy water. Do not use abrasive
cleaners/scourers. Dishwasher.
Warming zone (some models only) Toughened glass
Hot soapy water, cream cleaner/scourer if necessary.
Outside of Cooker
Part
Finish
Recommended Cleaning Method
Enamel or paint
Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.
Stainless steel
E-cloth (electrical retailers) or microfibre all-purpose cloth
(supermarket).
Sides and plinth
Painted surface
Hot soapy water, soft cloth.
Splashback/rear grille
Enamel or stainless steel
Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.
Control panel
Paint, enamel or stainless steel
Warm soapy water. Do not use abrasive cleaners on lettering.
Control knobs/handles & trims
Plastic/chrome, copper or
lacquered brass
Warm soapy water, soft cloth.
Brass
Brass polish.
Toughened glass
Hot soapy water, cream cleaner/scourer if necessary.
Finish
Recommended Cleaning Method
Door, door surround and storage
drawer exterior
Oven door glass/glass lid
Oven and Grill
Part
Sides, floor & roof of oven NOT
COOK & CLEAN OVEN PANELS (see Enamel
below)
Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW
MANUFACTURER’S INSTRUCTIONS.
Do not allow contact with the oven elements.
Cook & Clean oven panels (some
models only)
Special enamel that partly
cleans itself
This surface cleans itself at 200 °C and above, or the panels can be
removed and washed with hot soapy water and a nylon brush (see
‘The Ovens’ in ‘Cleaning your Cooker’).
Oven shelves, Handyrack, grill
trivet, Handygrill rack (some
models only)
Chrome
An oven interior cleaner that is suitable for chrome. Soap filled
pad. Dishwasher.
Grill pan/meat tin (some models
only)
Enamel
Hot soapy water. Soap filled pad. Dishwasher.
Table 5-1
17
6. Troubleshooting
Hotplate ignition or hotplate burners faulty
Is the power on? Is the clock illuminated?
If there is an installation problem and I don’t get my
original installer to come back to fix it who pays?
You do. Service organizations will charge for their call
outs if they are correcting work carried out by your
original installer. It is in your interest to track down your
original installer.
If not, there maybe something wrong with the power
supply.
Are the sparker (ignition electrode) or burner slots
blocked by debris?
Power failure
In the event of a failure in the electrical supply,
remember to reset the clock to make sure that the
timed oven continues to operate.
Are the burner trim and caps correctly located? See the
section on ‘Cleaning’?
Hotplate burners will not light
Make sure that the burner parts have been replaced
correctly after wiping or removing for cleaning.
Food is cooking too slowly, too quickly, or burning
Cooking times may differ from your previous oven.
Check that there is not a problem with your gas
supply. You can do this by making sure that other gas
appliances you may have are working.
Do the burners spark when you push the control?
Check that you are using the recommended
temperatures and shelf positions – see the oven
cooking guide. The oven control settings and cooking
times are intended to be used only as a guide.
If not, verify that the power is on by checking that the
clock is illuminated.
Individual tastes may require the temperature to be
altered either way, to get the results you want.
Steam is coming from the oven
When cooking foods with high water content (e.g. oven
fries) there may be some steam visible at the rear grille.
The oven is not cooking evenly
Do not use a baking tray with dimensions larger than
those specified in the section on ‘General Oven Tips’.
Take care when opening the oven door, as there may
be a momentary puff of steam when the oven door
is opened. Stand well back and allow any steam to
disperse.
If you are cooking a large item, be prepared to turn it
round during cooking.
If two shelves are used, check that space has been left
for the heat to circulate. When a baking tray is put into
the oven, make sure that it is placed centrally on the
shelf.
What cleaning materials are recommended for the
cooker?
See the ‘Cleaning’ section for recommended cleaning
materials.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held firmly
against the seal.
Never use caustic or abrasive cleaners as these will
nn
damage the surface.
A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered.) If the cooker is not level arrange for
your supplier to level it for you.
An oven fan is noisy
The note of the oven fan may change as the oven heats
up – this is perfectly normal.
The knobs get hot when I use the oven or the grill. Can I
avoid this?
Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Do not leave the oven door
open.
Oven not coming on
Is the power on? Is the clock illuminated? If not, there
may be something wrong with the power supply.
Is the cooker supply on at the isolator switch?
Has the time of day been set?
Make sure that the grill pan is pushed right back to the
‘back stop’ when grilling.
Is the key symbol [] showing in the display to signify
that the oven is locked? See the ‘Clock’ section of the
instructions for more information on the key lock
feature.
Always grill with the grill compartment door open.
The fascia gets hot when I use the oven or grill
The cooker is cooled by a fan. If the fascia becomes
excessively hot when the cooker is in use then the
cooling fan may have failed. Should this occur please
contact your installer, a qualified repair engineer or
Customer Service to arrange for its repair.
The timed oven is not coming on when automatic cooking
Has the oven knob been left in the OFF position by
mistake?
Is the oven locked (see above)?
18
Oven temperature getting hotter as the cooker gets older
If turning the temperature down using the oven control
knob has not worked, or has only worked for a short
time, then you may need a new thermostat. This should
be fitted by a service person.
Fig.6-1
ArtNo.324-0005 Oven light bulb
An oven light is not working
The bulb has probably burnt out. You can buy a
replacement bulb (which is not covered under the
warranty) from a good electrical shop. Ask for a 15 W –
230 V lamp, FOR OVENS. It must be a special bulb, heat
resistant to 300 °C (Fig.6-1).
Fig.6-2
Turn off the power at the circuit breaker.
Before removing the existing bulb, turn off the power
supply and make sure that the oven is cool. Open the
oven door and remove the oven shelves.
ArtNo.324-0007 Unscrewing the bulb cover
Unscrew the bulb cover by turning counter-clockwise. It
may be very stiff (Fig.6-2).
Taking care to protect your fingers with a glove in case
the bulb should shatter, unscrew the old bulb.
Screw in the new bulb; screw back the bulb cover. Turn
on the circuit breaker and check that the bulb now
lights.
Fig.6-3
The oven door is misaligned
The bottom hinge of either oven door can be adjusted
to alter the angle of the door (Fig.6-3). Loosen the
bottom hinge fixing screws and use the notch and a flat
bladed screwdriver to move the position of the hinge to
set the hinge position (Fig.6-4).
Effect of hinge adjustment – exaggerated for clarity
Retighten the hinge screws.
Centreline of hinge pin
ArtNo.320-0007 Oven door hinge adjustment 2
Oven door omitted for clarity
19
Fig.6-4
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
7. Installation
Dear Installer
In the UK the cooker must be installed in
accordance with:
Before you start your installation, please complete the details
below, so that, if your customer has a problem relating to
your installation, they will be able to contact you easily.
•
•
•
Installer’s Name
•
•
Installer’s Company
All relevant British Standards / Codes of Practice, in
particular BS 5440 Part 2.
For Natural Gas – BS 6172 and BS 6891.
For LP Gas – BS 5482-1 (when the installation is in a
permanent dwelling). This appliance should not be
installed in a boat or caravan.
The Gas Safety (Installation and Use) regulations.
The relevant Building / IEE regulations.
In the Republic of Ireland the cooker must be
installed in accordance with:
ArtNo.050-0011 - Installer information table
The installation must be carried out by a competent person
and installed in accordance with the current edition of IS 813
“Domestic Gas Installations”, the current Building Regulations
and reference should be made to the current ETCI rules for
electrical installation.
Installer’s Telephone Number
Appliance Serial Number
Provision of Ventilation
This appliance is not connected to a combustion products
evacuation device. Particular attention shall be given to the
relevant requirements regarding ventilation.
All rooms require a window that can be opened, or
equivalent, while some rooms require a permanent vent in
addition to the window.
Safety Requirements and Regulations
This cooker must be installed in accordance with
nn
the relevant instructions in this booklet, with the
relevant national and local regulations, and with
the local gas and electricity supply companies’
requirements.
In the UK:
The room containing the cooker should have an air supply
in accordance with BS 5440 Part 2. All rooms require an
openable window or equivalent, while some rooms require
a permanent vent in addition to the openable window. The
cooker should not be installed in a bedsitting room with
volume less than 20 m³. If it is installed in a room of volume
less than 5 m³ an air vent of effective area 100 cm² is required;
if it is installed in a room of volume between 5 m³ and 10 m³,
an air vent of effective area 50 cm² is required; while if the
volume exceeds 11 m³, no air vent is required.
Before installation, make sure that the cooker is
nn
suitable for your gas type and supply voltage. See
the data badge.
The appliance must be installed in accordance with
nn
the regulations in force and only in a well-ventilated
space.
Read the instructions before installing or using this
nn
appliance.
If there are other fuel burning appliances in the same room,
BS 5440 Part 2 should be consulted to determine the requisite
air vent requirements.
In your own interest and that of safety, it is law
that all gas appliances be installed by competent
persons. Failure to install the appliance correctly
could invalidate any warranty or liability claims and
lead to prosecution.
nn
In the Republic of Ireland:
Reference should be made to the current edition of IS 813,
which makes clear the conditions that must be met to
demonstrate that sufficient ventilation is available.
This appliance can be converted for use on another
gas.
nn
20
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Checking the Parts:
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner but
NOT in a room containing a bath or shower.
3 pan supports
Griddle
Wok cradle
Grill pan and trivet
This appliance is designed for domestic cooking only. Use
for any other purpose could invalidate any warranty or
liability claim.
Note: An appliance for use on LPG must not be installed
in a room or internal space below ground level, e.g. in a
basement.
Conversion
This appliance is supplied set for G20 20 mbar Cat II2H3+.
ArtNo.000-0009 Wok ring, cast
A conversion kit for another gas is available for the cooker.
ArtNo.330-0001 - Grill pan
If the appliance is to be converted to another gas we
recommend that this is carried out before installation.
1 flat shelf
1 drop shelf
Roasting tin
Handyrack
After converting the appliance, please attach the Gas
Conversion sticker over the appropriate area of the data
badge – this will identify the gas type for which the appliance
is now set.
You will need the following equipment to complete the
cooker installation satisfactorily:
•
•
•
•
Stability bracket: If the cooker is to be supplied with
gas through a flexible hose, a stability bracket or chain
MUST be fitted.
These are not supplied with the cooker but are
available at most builders’ merchants.
Gas pressure tester/manometer.
Flexible gas hose: Must be in accordance with the
relevant standards.
Multimeter: For electrical checks.
ArtNo.324-0003 Handyrack
ArtNo.324-0004 Roasting tin
Tall oven shelves and shelf
supports
You will also need the following tools:
1. Electric drill
2. Masonry drill bit (only required if fitting the cooker on a
stone or concrete floor)
3. Wall plugs (only required if fitting the cooker on a stone
or concrete floor)
4. Steel tape measure
5. Cross head screwdriver
6. Flat head screwdriver
7. Spirit level
8. Pencil
9. Adjustable spanner
10. Screws for fitting stability bracket
11. 4 mm & 3 mm Allen keys
12. 13 mm spanner or socket wrench
ArtNo.000-0010 Tall oven shelves
21
Plinth
ArtNo.350-0008 - 90 SC plinth
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Fig.7-1
Positioning the Cooker
ArtNo.090-0009 - 90 2BC cooker min spacings
75 mm
min
Fig.7-1 and Fig.7-2 show the minimum recommended
distance from the cooker to nearby surfaces.
75 mm
min
650 mm
min
The cooker should not be placed on a base.
Above hotplate surround should be level with, or above,
any adjacent work surface. A gap of 75 mm should be left
between each side of the cooker ABOVE the hotplate level
and any adjacent vertical surface.
For non-combustible surfaces (such as unpainted metal or
ceramic tiles), this can be reduced to 25 mm.
905 mm min
930 mm max
A minimum space of 650 mm is required between the top of
the hotplate and a horizontal combustible surface.
*Any cookerhood should be installed in accordance with the
hood manufacturer’s instructions.
Fig.7-2
**Any splashback must be fitted in accordance with the
manufacturers instructions. Allowance should be made for the
additional height of the flue trim, which is fitted to the cooker
hob.
900 mm min*
ArtNo.090-0017 - 90 6BC min positions above cooker
410 mm min
5 mm
Surfaces of furniture and walls at the sides and rear of the
appliance should be heat, splash and steam resistant. Certain
types of vinyl or laminate kitchen furniture are particularly
prone to heat damage and discolouration.
5 mm
**
ºC
ºC
We cannot accept responsibility for damage caused by
normal use of the cooker to any material that de-laminates
or discolours at temperatures less than 65 °C above room
temperature.
Fig.7-3
We recommend a gap of 910 mm between units to allow
for moving the cooker. Do not box the cooker in – it must
be possible to move the cooker in and out for cleaning and
servicing.
A clearance of 130 mm is required if the cooker is near a
corner of the kitchen to allow the oven doors to open
(Fig.7-3). The actual opening of the doors is slightly less but
this allows for some protection of your hand as you open the
door.
130 mm min
Moving the Cooker
On no account try and move the cooker while it is
nn
plugged into the electricity supply.
Fig.7-4
The cooker is very heavy, so take great care.
nn
We recommend that two people manoeuvre the cooker.
Make sure that the floor covering is firmly fixed, or removed,
to prevent it being disturbed when moving the cooker
around.
To help you, there are two levelling rollers at the back, and
two screw-down levelling feet at the front.
Remove the polystyrene base pack. From the front, tilt the
cooker forward and remove the front half of the polystyrene
base (Fig.7-4). Repeat from the back and remove the rear half
of the polystyrene base.
22
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Lowering the Two Rear Rollers
Fig.7-5
To adjust the height of the rear of the cooker, first fit a 13 mm
spanner or socket wrench onto the hexagonal adjusting
nut (Fig.7-5). Rotate the nut – clockwise to raise – counterclockwise to lower.
Make 10 complete (360°) turns clockwise.
Make sure you lower BOTH REAR ROLLERS.
Completing the Move
Unfold the rear edge of the cardboard base tray. Open the
grill door and right-hand oven door so that you can get a
good grip on the bottom of the fascia panel as you move the
oven (Fig.7-6).
Fig.7-6
Carefully push the cooker backwards off the cardboard base.
Remove the pack base tray.
Position the cooker close to its final position, leaving just
enough space to get behind it.
ArtNo.010-0004 Moving the cooker
DO NOT use the door handles or control knobs to
manoeuvre the cooker.
nn
Fitting the Stability Bracket or Chain
Fig.7-7
Unless otherwise stated, a cooker using a flexible gas
connector must be secured with a suitable stability device.
Stability chain
Suitable stability devices are shown in Fig.7-7, Fig.7-8 and
Fig.7-9.
If you are using a stability chain (Fig.7-7) then the chain
should be kept as short as is practicable and fixed firmly to
the rear of the cooker.
If you are using a stability bracket (Fig.7-8 and Fig.7-9), then
adjust the bracket to give the smallest practicable clearance
between the bracket and the engagement slot in the rear of
the cooker.
Fig.7-8
Stability bracket
Fit the bracket so that it engages as far as possible over the
chassis of the cooker.
Cooker
3 mm min
ArtNo.070-0014 - Stability bracket - WallFloor
fitting
Typical floor mounting
Fig.7-9
Outer stability
bracket
Cooker
3 mm min
Wall
Floor
Typical wall mounting
23
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Repositioning the Cooker Following
Connection
If you need to move the cooker once it has been connected
then you need to unplug it and, having gripped under the
fascia panel and lifted the front of the cooker slightly
(Fig.7-6), you need to check behind the cooker to make sure
that the gas hose is not caught.
As you progress, make sure that both the electricity cable and
gas hose always have sufficient slack to allow the cooker to
move.
With a stability chain fitted, release it as you ease the cooker out.
Do not forget to refit it when you replace the cooker.
When you replace the cooker, again check behind to make
sure that the electricity cable and gas hose are not caught or
trapped.
Conversion to Another Gas
If the appliance is to be converted to another gas do the
conversion at this point. See the conversion section of these
instructions and see the instructions in the conversion kit.
Levelling
You are recommended to use a spirit level on a shelf in one of
the ovens to check for level.
Place the cooker in its intended position taking care not to
twist it within the gap between the kitchen units as damage
may occur to the cooker or the units.
The front feet and rear rollers can be adjusted to level the
cooker.
To adjust the height of the rear of the cooker, use a 13 mm
spanner or socket wrench to turn the adjusting nuts at the
front bottom corners of the cooker.
To set the front turn the feet bases to raise or lower.
24
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Gas Connection
240
This must be in accordance with the relevant standards.
A
100
The flexible hose (not supplied with the cooker) must be
in accordance with the relevant standards. Hoses may be
purchased at most builders’ merchants.
100
300
We recommend that a Micropoint gas hose is used when
installing this appliance.
The gas supply needs to terminate with a side-facing elbow
with a down-facing bayonet.
Gas inlet
The connector is located just below the hotplate level at the
rear of the cooker. If in doubt contact your supplier.
The rear cover boxes limit the position of the supply point.
Because the height of the cooker can be adjusted and
each connection is different, it is difficult to give precise
dimensions.
ArtNo.090-0027 - 90 Elan gas connections
Although a 900 mm hose can be used, a 1100 mm hose
will allow slightly more flexibility in the positioning of the
bayonet and make moving the cooker easier.
All dimensions in millimetres
The hose should be fitted so that both inlet and outlet
connections are vertical so that the hose hangs downwards in
a ‘U’ shape.
Ideally the hose supply connection should be within the
shaded area ‘A’ (Fig.7-10).
For Natural Gas, the flexible hose must be in accordance with
BS 669. For LP Gas, it should be capable of 50 mbar pressure,
70 °C temperature rise, and carry a red stripe, band or label. If
in doubt contact, your supplier.
Screw connect the threaded end of the hose into the gas
inlet.
After completing the gas connection, make sure that the
cooker is gas sound with a pressure test.
Pressure Testing
The gas pressure can be measured at one of the hotplate
burner injectors (not the wok burner).
Lift off a burner head. Fit the pressure gauge to the injector.
Turn on and light one of the other hotplate burners.
Turn on the control knob for the burner with the pressure
gauge fitted to let gas through.
See the data badge for test pressures.
Turn off the burners. Make sure that you reassemble the
burner top in the correct way on the burner body.
25
Fig.7-10
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Electrical Connection
Fig.7-11
The cooker must be installed by a qualified electrician, in
accordance with all relevant British Standards/Codes of
Practice (in particular BS 7671), or with the relevant national
and local regulations.
L
N
Current Operated Earth Leakage Breakers
The combined use of your cooker and other domestic
appliances may cause nuisance tripping, so we
recommend that the cooker is protected on an individual
RCD (Residual Current Device) or RCBO (Residual Current
Breaker with Overload).
10 mm² max
ArtNo.130-0010 Electrical connections single-phase6 mm² max
230 V ac 50 Hz
IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED
ELECTRICIAN.
Fig.7-12
Note: The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double-pole
switch, having a contact separation of at least 3 mm in all
poles.
L1
N
L3
L2
6 mm² max
3N ac
230/400 V 50 Hz
The cooker MUST NOT be connected to an ordinary
nn
domestic power point.
6 mm² max
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect
the mains cable to the correct terminals for your electrical
supply type (Fig.7-11 and Fig.7-12). Check that the links are
correctly fitted and that the terminal screws are tight. Secure
the mains cable using the cable clamp.
10 mm² max
Final Checks
Hotplate Check
Check each burner in turn (refer to the ‘Hotplate Burners’
section at the front of the instructions).
Grill Check
Turn on the grill control and check that the grill heats up.
Oven Check
Set the clock as described earlier in the instructions, and then
turn on the ovens. Check that the oven fans start to turn and
that the ovens start to heat up.
Note: The oven light bulb is not included in the guarantee.
Turn off the oven.
26
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Final Fitting
Fig.7-13
Fitting the Plinth
Loosen the 3 screws along the front bottom edge of the
cooker. Hook the central keyhole over the central screw.
Twist and fit each end keyhole over their respective screws.
Tighten the fixing screws.
ArtNo.000-0006 - Securing the 110 plinth
Remove the 3 screws for the plinth mounts along the front
bottom edge of the cooker (Fig.7-13). Fasten the plinth using
these screws (alternative colour screws can be found in the
loose parts pack).
Customer Care
Installer: Please complete your details in this guide, inform
the user how to operate the cooker and hand over the
instructions.
Thank you.
27
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
8. Conversion to LP Gas
Check the ‘Technical Data’ section at the back of the book
that the hob is convertible to the gas you want to use.
A suitably competent person must perform the
conversion. After conversion the installation must
comply with the relevant regulations and also the
local electricity supply company requirements. Read
the instructions before converting this appliance.
Fig.8-1
nn
B
Failure to convert the appliance correctly could
nn
invalidate any warranty or liability claims and lead
A
ArtNo.311-0010 Injectors
to prosecution.
C
When servicing or replacing gas-carrying
nn
components disconnect from the gas supply before
A – Jet, B – Internal injector, C – External injector
starting operation. Check the appliance is gas sound
after completion.
Fig.8-2
DO NOT use reconditioned or unauthorised gas
nn
controls.
Disconnect from the electricity supply before
nn
servicing.
Before electrical reconnection, check that the
nn
appliance is electrically safe.
Injectors
Remove the burner caps and heads. Remove the old jets
(Fig.8-1). Fit the new jets (see ‘Technical Data’ for the correct
jets). Reassemble in the reverse order.
ArtNo.270-0032 - 90 Prof+ FX - Removing the control panel
Tap Adjustment
Removing the Control Panel
Remove the 3 fixing screws underneath the control panel
(Fig.8-2). The control panel will drop down slightly. It is held
at the top by three holes in the top edge that locate on the
tags on the inner panel (Fig.8-2). Lift the control panel clear of
the tags and pull forwards, taking care not to damage or strain
the wiring.
Fig.8-3
ArtNo.0102-0011 - Screwing
the control valve bypass screw
Bypass Screw Adjustment
Turn the bypass screw on each control clockwise until it stops
(Fig.8-3). Refit the control panel and control knobs.
Stick on Label
Stick the LP gas label over the natural gas part of the
appliance data label.
Pressure Testing
Connect the appliance to the gas supply.The gas pressure can
be measured at one of the hotplate burner jets (not the wok
burner). Lift off a burner head. Fit the pressure gauge to the
jet. Turn on and light one of the other burners with a match.
Turn on and press in the control knob for the burner with
the pressure gauge fitted. After checking the pressure, turn
off the taps and replace the burner head.Reassemble burner
top, making sure it is reassembled in the correct way on the
burner body. Check the appliance is gas sound. Check
operation of all the burners.
28
9. Circuit Diagram
bk
r
2
A1
1
v
r
P1
b
B1a
P2
bk
J
v
v
v
P095199
v
B1
r
b
J
br
bk
A2
bk
v
b
br
r
b
r
b
gr
or
H
A3
v
A4
H
b
P8
v
7
P7
r
P6
w
B3
r
6
B4
gr
5
b
B5
B6
b
b
8
b
b
B7
B2
P4
y
3
P3
2
P2
1
P1
or
bk
G2
b
w
b
w y
w
J
1
2
D1
bk
y
P038434
b
br
br
b
G1
4
or
L/1
N/2
b
w
P5
w
b
bk
N/2
br
y
J
br
r
r
w w
w
C
bk
v
bk
br
v
br
v
br
v
br
br
v
b
F1
r
K
b
v
2
y
or
1
r
P2
D2
P1
br
D3
v
or
D4
f
d
e
c
b
b
b
H
a
b
v
br
v
1
2
F2
br
br
br
w
b b b
w
P095199
b
b
b b b
L
E
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Description
A1
Grill front switch
A2
Grill energy regulator
A3
Code Description
C
Code Colour
Clock
b
Blue
D1
Right-hand fan oven thermostat
br
Brown
Grill element left-hand side
D2
Right-hand fan oven control switch
bk
Black
A4
Grill element right-hand side
D3
Right-hand fan oven element
or
Orange
B1
Left-hand multi-function oven thermostat
D4
Right-hand fan oven fan
r
Red
B1a
Left-hand multi-function oven thermostat
switch
F1
Ignition switch
v
Violet
B2
Left-hand multi-function oven switch
F2
Ignition generator
w
White
B3
Left-hand multi-function oven base element
G1
Oven light switch
y
Yellow
G2
Oven light
g/y
Green/yellow
B4
Left-hand multi-function oven top element
(outer pair)
H
Thermal cut-out
gr
Grey
B5
Left-hand multi-function oven browning
element (inner pair)
J
Neon
K
Cooling fan
B6
Left-hand multi-function oven fan element
B7
Left-hand multi-function oven fan
29
10. Technical Data
ArtNo.107-0005 - Technical data - 90DF - Classic DL
THE COOKER IS CATEGORY: CatII2H3+.
It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.
COUNTRY OF DESTINATION: GB, IE.
Connections
Gas (Rp ½ at rear right-hand side)
Natural gas
20 mbar
Butane
29 mbar
Propane
37 mbar
Electric
230/400 V 50 Hz
See the appliance badge for test pressures.
Dimensions
Overall height
minimum 905 mm
maximum 930 mm
Overall width
900 mm
Overall depth
650 mm (over handles), 600 mm (to fascia)
Minimum height above cooker
650 mm
Refer to 'Positioning the Cooker'.
Ratings
Hotplate
Bypass Screw*
Natural Gas 20 mb
LP Gas
Injector
internal 78
Injector
internal 53
Wok burner
57
3.5 kW
Large burner
40
3.0 kW
134
3.0 kW (210 g/h)
87
Medium burner
32
1.7 kW
109
1.7 kW (119 g/h)
68
Small burner
28
1.0 kW
75
1.0 kW (70 g/h)
51
external 126
3.5 kW (246 g/h)
external 82
* The valves in this cooker are fitted with adjustable bypass screws. The cooker is supplied with the bypass screws set for
Natural gas. For LPG conversion the bypass screws must be screwed all the way down.
Oven Efficiency
Ovens
Maximum output
Energy efficiency class on a scale of A (more efficient) to G (less efficient)
Energy consumption based on standard load
Oven usable volume (litres)
Size
Time to cook standard load
Surface area of the grid
Grill
Main Oven
Tall Oven
Multi-function
Forced Air Convection
3.7 kW
2.5 kW
A
A
0.95 kWh
0.99 kWh
69
66
Large
Large
41 minutes
49 minutes
1400 cm
790 cm2
2
2.3 kW
Maximum total electrical load at 230 V (approximate total including oven lights, oven fan, etc.): 8.6 kW.
30
For warranty compliance, the requirements are
that the appliance:
Name of Appliance & Colour*
•
Has been correctly installed in accordance with current
legislation, relevant British and European Standards and Codes
of Practice, by a suitably competent person registered with
Gas Safe or equivalent body and, where applicable, a qualified
electrician.
•
Has been used solely for domestic cooking purposes.
•
If in use in the UK*, has not been taken abroad as a personal
export. (In the Republic of Ireland conditions may vary, so
consult your retailer.)
•
Is not second-hand or a refurbished appliance. The
manufacturer’s warranty is not transferable.
•
Has not been subject to misuse, accidental damage or
modification, and has not deteriorated due to normal
domestic wear and tear, and the manufacturer’s
recommendations concerning cleaning materials have been
followed.
•
Has not been repaired by persons or organisations other than
those authorised to act on behalf of AGA Rangemaster.
Appliance Serial Number*
Natural Gas
LP Gas
Dual Fuel
Electric
Fuel Type*
Retailer’s Name & Address
Date of Purchase
Exceptions:
Installer’s Name & Address
Installer’s Telephone Number
•
Items not included under the free 1 year guarantee include
pan supports, griddles, wok rings, baking trays, grill pans,
trivets, filters, light bulbs and other consumable accessories.
•
Any damage caused other than through normal use.
•
Breakdowns associated with cooking spillage.
•
Cosmetic deterioration deemed to be normal wear and tear.
This warranty is in addition to your Statutory Rights.
* Only certain models can be adapted for use with Mains Gas
supplied in the Channel Islands and Isle of Man.
Date of Installation
OUT OF WARRANTY
Service work should only be carried out by technically competent
and suitably qualified personnel.
* This information is on the appliance data badge - look in the appliance
instructions to find out where the data badge is located.
CONSUMER SERVICE
If you have any product enquiries, or in the event of a problem
with your appliance once it has been installed, please
telephone 0870 789 5107.
CONSUMER SERVICE LINES OPEN:
For your own safety, always make sure that work is carried out by
a Gas Safe registered engineer for gas appliances or an approved
electrician for electrical models.
For a competitive quote and to arrange for a Rangemaster approved
engineer to attend, call Consumer Services on: 0870 7895107.
SPARE PARTS
Monday to Thursday 8am–6pm
Friday 8am–5pm
Saturday 9am–1pm
To maintain optimum and safe performance, we recommend that
only genuine Rangemaster spare parts are used. These are available
from most major spares stockists, including ourselves.
WARRANTY
Contact Consumer Services on 0870 7895107, who will be happy to
help.
Your manufacturer warranty covers goods of our own brand for
defective workmanship and materials for a period of 1 year from the
date of purchase. This warranty covers mechanical breakdown and
proven cosmetic and manufacturing defects.
STANDARDS
You will receive an additional FREE full 12 months guarantee by
registering your purchase using the FREEPOST form provided.
Alternatively, call free on 0800 587 5747, quoting reference
RMGX57A, or register online at www.rangemaster.co.uk.
Any damage, blemishes or chips identified upon receipt of the
product must be reported within 90 days – proof of purchase
may be required to establish validity. Scratches on the surface of
ceramic hobs must be reported within 14 days. Scratches caused
by usage are not covered. Accidental damage is not covered by the
manufacturer’s warranty.
Rangemaster cookers are designed and manufactured to a
recognised international quality standard, which meets the
requirements of BS EN ISO 9001, BS EN ISO 14001 and OHSAS 18001
for continually improving environmental procedures.
Rangemaster cookers comply with the essential requirements of the
appropriate European Directives, and carry the CE mark.
ALSO PART OF THE RANGEMASTER COLLECTION...
Refrigeration
Built-in Cooking
Dishwashing
Sinks & Taps
Clarence Street
Royal Leamington Spa
Warwickshire
CV31 2AD
England
Tel: +44 (0) 1926 457400
Fax: +44 (0)1926 450526
E-mail: consumers@rangemaster.co.uk
Consumer Services Tel: +44 (0) 870 7895107
www.rangemaster.co.uk
Britain’s No.1 Range Cooker
For ROI Enquiries Tel: 1850 302 502
Search Rangemaster UK
Registered in England and Wales. Registration No. 354715 Registered Office: Juno Drive, Leamington Spa, Warwickshire, CV31 3RG
Rangemaster continuously seeks improvements in specification, design and production of products and thus, alterations take place
periodically. Whilst every effort is made to produce up-to-date literature, this booklet should not be regarded as an infallible guide to
current specification, nor does it constitute an offer for the sale of any particular appliance.