Mitsubishi F940GOT-LWD-E Specifications

…
This manual contains text, diagrams and explanations which will guide the reader in the correct
installation, safe use and operation of the F94*GOT-*WD-E and should be read and understood before
attempting to install or use the unit. Further information can be found in the associated manuals list below.
Specifications are subject to change without notice
a) Any engineer using the product associated with this manual, should be of a competent nature,
trained and qualified to the local and national standards. These engineers should be fully aware of
all aspects of safety with regards to automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and qualified to
the local and national standards.
c) All operators of the completed equipment should be trained to use that product in a safe and
co-ordinated manner in compliance to established safety practices.
Note: The term ‘completed equipment’ refers to a third party constructed device which contains or uses
the product associated with this manual.
Note’s on the Symbols Used in this Manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the users personal safety and protect the integrity of equipment.
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property
damage.
Refer to the manual of the connected programmable controller for details concerning that unit.
1. Introduction
Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage
that may arise as a result of the installation or use of this equipment.
•
All examples and diagrams shown in this manual are intended only as an aid to understanding the
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the
product based on these illustrative examples.
•
Manual Name
F940GOT Series
| (F94*GOT-*WD-E)
Installation Manual
Manual Number
JY997D94201
JY992D09101
(separate volume)
Describes the operation and use of the GOTF900 Series graphic operation terminals and
GT Designer2.
GOT-F900 Series
Operation Manual
GOT-F900 Series
~ Hardware Manual
(connection diagram)
GOT-F900
~ OPERATION MANUAL
(describes GT Designer2)
~
|
|
GT Designer2 Version1
Operating Manual
GT Designer2 Version1
Reference Manual
Software Name
GOT-F900 and GOT-A900 Series (for Windows) screen creation software.
GT Designer
SW…D5C-GOTR-PACKE
(… indicates version)
GOT-F900 and GOT-A900 Series (for Windows) screen creation software.
SW1-A edition of SW1D5C-GOTR-PACKE or later
FX-PCS-DU/WIN-E
GOT-F900 Series (for Windows) screen creation software.
SW0PC-FXDU/WIN-E version 2.00 or later
Production Name
F940GOT-LWD-E
FX-50DU-CAB0
Description
Graphic operation terminal main unit
SWD: 8 colors
LWD: White and black
FX-50DU-CAB0/EN
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
FX-50DU-CAB0-**M
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight.
** M is cable length. 1M: 1m (3' 3"), 10M: 10m (32' 9"), 20M: 20m (65' 7"),
30M: 30m (98' 5")
QC30R2
Communication cable (GOT ↔ CPU port in Q series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
FX-232CAB-1
Data exchange cable (GOT ↔ Personal computer <9-pin D-sub>)
PM-20BL
Battery for Alarm history, sampling and current time data retertion.
JY992D98601
This manual contains explanations for
installation and operating procedure of F9GT40FMB data transfer adapter.
1 0 (0 .3 9 ")
i)
h )
2 4 V D C
-
F9GT-40PSC
Transparent protection sheet for F940GOT (5 pieces)
F9GT-40LTS
Backlight for F940GOT
F9GT-40UMB
Data transfer adapter
F9GT-40FMB
Data transfer adapter (Flash memory built in)
Caution
During abnormal communication (including cable breakages) when monitor is executed within
the GOT, communication between the GOT and programmable controller CPU is interrupted.
It is then impossible to operate switches or devices in the PLC through the GOT.
Communication and normal operation resumes when the GOT system is correctly configured.
DO NOT configure emergency stop or safety features to operate through the GOT, and be
sure that there is no adverse consequences in the event of a GOT - PLC communications
malfunction.
+
6 .5 (0 .2 5 ")
6 .5 (0 .2 5 ")
2 3 (0 .9 1 ") 2 3 (0 .9 1 ")
1 5 2 (5 .9 8 ")
a) Display
c) Communication ports
5 (0 .2 0 ")
b) Mounting bracket hole
Port
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight.
Cable length is 3m (9' 10").
Describes wiring and installation of the GOTF900 Series graphic operation terminals.
FX-PCS-DU/WIN-E
|
SOFTWARE MANUAL
e )
g )
1.1 Product Lists
JY992D94801
(separate volume)
JY992D68301
Describes the operation of FX-PCS-DU/WIN(included with the screen
E screen creation software.
creation software)
d )
5 7 (2 .2 4 ")
f )
FX-40DU-CAB-**M
Describes the specifications and setting of
object functions in GT Designer2 (SW*D5CGTD2-E).
1 0 (0 .3 9 ")
Version
GT Designer2
SW…D5C-GTD2-E
(… indicates version)
JY992D94701
(separate volume)
(PDF files on CD-ROM
included with product)
5 (0 .2 0 ")
1 6 2 (6 .3 8 ")
3) Display screens are created using the following software.
Communication cable (GOT ↔ CPU port in FX, FX2C, A or QnA series PLC)
The connector on the GOT side is wired straight.
** M is cable length. 10M: 10m (32' 9"), 20M: 20m (65' 7"), 30M: 30m (98' 5")
Describes the operation of GT Designer
Included with the screen
(SW*D5C-GOTR-PACKE) and data transfer to
creation software
the GOT-900 Series. (Refer to the help file)
F9GT-40FMB
User’s Manual
G O T
Describes the operation and use of the GOTF900 Series graphic operation terminals, GT
Designer and FX-PCS-DU/WIN-E.
(PDF files on CD-ROM
included with product)
b )
P O W E R
Communication cable (GOT ↔ CPU port in FX, FX2C, A or QnA series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
Describes the operation of GT Designer2
(SW*D5C-GTD2-E) and data transfer to the
GOT-900 Series.
c )
P r o g r a m m in g
p o rt
FX-40DU-CAB
GT Designer
|
Operating Manual
…
a )
2) PLC user programs can be downloaded, uploaded and
monitored using programming software GX-Developer or FX-PCS/WIN-E on a personal computer via
the GOT. Further information can be found in the GOT-F900 Series Operation Manual.
Description
Describes the specifications, wiring, and
installation of F940GOT Series graphic
operation terminal. (hardware)
MASS (Weight): 1 kg (2.2 lbs)
Mounting brackets, Tightening bolt (M3, 6 bolts),
Packing seal for dust and water resistance
P L C
1) The GOT can connect to MELSEC FX, A, QnA and Q PLCs
as well as a host of third party manufactured units. Further
information can be found in GOT-F900 Series Hardware
Manual.
Owing to the very great variety in possible application of this equipment, you must satisfy yourself as
to its suitability for your specific application.
Associated Manuals
Dimensions: mm (inches)
Accessory:
The F940GOT-*WD-E (hereafter called “GOT” or “F940GOT”) is
to be mounted on the face of a control panel or operations panel,
and connected to the programming por t (CPU por t) or the
communication port (communication port) of a PLC.
Various devices can be monitored and PLC data changed via the
GOT screens. Several display screens are built-in to the GOT,
and additional personalized screens can be created by the user.
F940GOT-SWD-E
•
1.2 Dimensions and Each Part Name
R S 4 2 2
This manual has been written to be used by trained and competent personnel. The definition of such a
person or persons is as follows:
•
~ Indispensable manual
| Either manual is necessary.
… Refer if necessary, please.
Do not lay signal cables near high voltage power cables or allow them to share the same
trunking duct, otherwise, effects of noise or surge induction are likely to take please. Keep
a safe distance of more than 100 mm from these wires.
Operate touch switches on the display screen by hand.
DO NOT use excessive force, or attempt operate them with hard or pointed objects.
The tip of a screw driver, pen or similar object for example may break the screen.
R S 2 3 2 C
Guidelines for the Safety of the User and Protection of the
F94*GOT-*WD-E
•
JY992D74101
1 4 0 (5 .5 1 ")
1 3 0 (5 .1 2 ")
JY992D94201E
Note;
2 3 (0 .9 1 ")
Installation Manual
Description
This manual contains explanations for
installation and operating procedure of F9GT40UMB data transfer adapter.
4 8 .5 (1 .9 0 ")
F940GOT Series(F94*GOT-*WD-E)
F9GT-40UMB
Manual
Manual Number
1 2 0 (4 .7 2 ")
1 3 0 (5 .1 2 ")
Manual Name
Description
RS-422
RS-422 Port for connecting either a PLC (including1:N connection) or
communication (computer link) unit <9-pin D-sub>
RS232C
RS-232C port for connecting eirher a personal computer, printer, bar-code reader
or 1:N connection
<9-pin D-sub>
d) Mounting bracket and tightening bolt
f) Expansion interface
h) Communication cable
e) PM-20BL battery
g) DC power supply terminal (M3)
i) Packing seal
2. Specifications
2.1 General Specifications
Item
Operating Temperature
Specifications
0 ~ 50 °C (32 ~ 122 °F)
[With expansion module: 0 ~ 40 °C (32 ~ 104 °F)]
Storage Temperature
-20 ~ 60 °C (-4 ~ 140 °F)
Humidity
35 ~ 85% Relative Humidity, No condensation
Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive
amount of electroconductive dust particles and must be no direct
sunlight. (Same as for saving)
Vibration Resistance
- intermittent vibration
10 ~ 57 Hz: 0.075 mm Half Amplitude
57 ~ 150 Hz: 9.8 m/s2 Acceleration
Sweep Count for X, Y, Z: 10 times (80 min. in each direction)
Vibration Resistance
- Continuous vibration
10 ~ 57 Hz: 0.035 mm Half Amplitude
57 ~ 150 Hz: 4.9 m/s2 Acceleration
Sweep Count for X, Y, Z: 10 times (80 min in each direction)
Shock Resistance
147m/s2 Acceleration,
3 times in each direction X, Y, and Z
Noise Immunity
1000 Vp-p, 1micro second, 30 ~ 100 Hz, tested by noise simulator
Dielectric Withstand Voltage 500 V AC > 1 min, tested between power terminals and ground
Insulation Resistance
5 MΩ > at 500 V DC, tested between power terminals and ground
Ground
Grounding resistance of 100 Ω or less. (class D)
Protection
IP 65F
…
This manual contains text, diagrams and explanations which will guide the reader in the correct
installation, safe use and operation of the F94*GOT-*WD-E and should be read and understood before
attempting to install or use the unit. Further information can be found in the associated manuals list below.
Specifications are subject to change without notice
a) Any engineer using the product associated with this manual, should be of a competent nature,
trained and qualified to the local and national standards. These engineers should be fully aware of
all aspects of safety with regards to automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and qualified to
the local and national standards.
c) All operators of the completed equipment should be trained to use that product in a safe and
co-ordinated manner in compliance to established safety practices.
Note: The term ‘completed equipment’ refers to a third party constructed device which contains or uses
the product associated with this manual.
Note’s on the Symbols Used in this Manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the users personal safety and protect the integrity of equipment.
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property
damage.
Refer to the manual of the connected programmable controller for details concerning that unit.
1. Introduction
Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage
that may arise as a result of the installation or use of this equipment.
•
All examples and diagrams shown in this manual are intended only as an aid to understanding the
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the
product based on these illustrative examples.
•
Manual Name
F940GOT Series
| (F94*GOT-*WD-E)
Installation Manual
Manual Number
JY997D94201
JY992D09101
(separate volume)
Describes the operation and use of the GOTF900 Series graphic operation terminals and
GT Designer2.
GOT-F900 Series
Operation Manual
GOT-F900 Series
~ Hardware Manual
(connection diagram)
GOT-F900
~ OPERATION MANUAL
(describes GT Designer2)
~
|
|
GT Designer2 Version1
Operating Manual
GT Designer2 Version1
Reference Manual
Software Name
GOT-F900 and GOT-A900 Series (for Windows) screen creation software.
GT Designer
SW…D5C-GOTR-PACKE
(… indicates version)
GOT-F900 and GOT-A900 Series (for Windows) screen creation software.
SW1-A edition of SW1D5C-GOTR-PACKE or later
FX-PCS-DU/WIN-E
GOT-F900 Series (for Windows) screen creation software.
SW0PC-FXDU/WIN-E version 2.00 or later
Production Name
F940GOT-LWD-E
FX-50DU-CAB0
Description
Graphic operation terminal main unit
SWD: 8 colors
LWD: White and black
FX-50DU-CAB0/EN
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
FX-50DU-CAB0-**M
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight.
** M is cable length. 1M: 1m (3' 3"), 10M: 10m (32' 9"), 20M: 20m (65' 7"),
30M: 30m (98' 5")
QC30R2
Communication cable (GOT ↔ CPU port in Q series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
FX-232CAB-1
Data exchange cable (GOT ↔ Personal computer <9-pin D-sub>)
PM-20BL
Battery for Alarm history, sampling and current time data retertion.
JY992D98601
This manual contains explanations for
installation and operating procedure of F9GT40FMB data transfer adapter.
1 0 (0 .3 9 ")
i)
h )
2 4 V D C
-
F9GT-40PSC
Transparent protection sheet for F940GOT (5 pieces)
F9GT-40LTS
Backlight for F940GOT
F9GT-40UMB
Data transfer adapter
F9GT-40FMB
Data transfer adapter (Flash memory built in)
Caution
During abnormal communication (including cable breakages) when monitor is executed within
the GOT, communication between the GOT and programmable controller CPU is interrupted.
It is then impossible to operate switches or devices in the PLC through the GOT.
Communication and normal operation resumes when the GOT system is correctly configured.
DO NOT configure emergency stop or safety features to operate through the GOT, and be
sure that there is no adverse consequences in the event of a GOT - PLC communications
malfunction.
+
6 .5 (0 .2 5 ")
6 .5 (0 .2 5 ")
2 3 (0 .9 1 ") 2 3 (0 .9 1 ")
1 5 2 (5 .9 8 ")
a) Display
c) Communication ports
5 (0 .2 0 ")
b) Mounting bracket hole
Port
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight.
Cable length is 3m (9' 10").
Describes wiring and installation of the GOTF900 Series graphic operation terminals.
FX-PCS-DU/WIN-E
|
SOFTWARE MANUAL
e )
g )
1.1 Product Lists
JY992D94801
(separate volume)
JY992D68301
Describes the operation of FX-PCS-DU/WIN(included with the screen
E screen creation software.
creation software)
d )
5 7 (2 .2 4 ")
f )
FX-40DU-CAB-**M
Describes the specifications and setting of
object functions in GT Designer2 (SW*D5CGTD2-E).
1 0 (0 .3 9 ")
Version
GT Designer2
SW…D5C-GTD2-E
(… indicates version)
JY992D94701
(separate volume)
(PDF files on CD-ROM
included with product)
5 (0 .2 0 ")
1 6 2 (6 .3 8 ")
3) Display screens are created using the following software.
Communication cable (GOT ↔ CPU port in FX, FX2C, A or QnA series PLC)
The connector on the GOT side is wired straight.
** M is cable length. 10M: 10m (32' 9"), 20M: 20m (65' 7"), 30M: 30m (98' 5")
Describes the operation of GT Designer
Included with the screen
(SW*D5C-GOTR-PACKE) and data transfer to
creation software
the GOT-900 Series. (Refer to the help file)
F9GT-40FMB
User’s Manual
G O T
Describes the operation and use of the GOTF900 Series graphic operation terminals, GT
Designer and FX-PCS-DU/WIN-E.
(PDF files on CD-ROM
included with product)
b )
P O W E R
Communication cable (GOT ↔ CPU port in FX, FX2C, A or QnA series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
Describes the operation of GT Designer2
(SW*D5C-GTD2-E) and data transfer to the
GOT-900 Series.
c )
P r o g r a m m in g
p o rt
FX-40DU-CAB
GT Designer
|
Operating Manual
…
a )
2) PLC user programs can be downloaded, uploaded and
monitored using programming software GX-Developer or FX-PCS/WIN-E on a personal computer via
the GOT. Further information can be found in the GOT-F900 Series Operation Manual.
Description
Describes the specifications, wiring, and
installation of F940GOT Series graphic
operation terminal. (hardware)
MASS (Weight): 1 kg (2.2 lbs)
Mounting brackets, Tightening bolt (M3, 6 bolts),
Packing seal for dust and water resistance
P L C
1) The GOT can connect to MELSEC FX, A, QnA and Q PLCs
as well as a host of third party manufactured units. Further
information can be found in GOT-F900 Series Hardware
Manual.
Owing to the very great variety in possible application of this equipment, you must satisfy yourself as
to its suitability for your specific application.
Associated Manuals
Dimensions: mm (inches)
Accessory:
The F940GOT-*WD-E (hereafter called “GOT” or “F940GOT”) is
to be mounted on the face of a control panel or operations panel,
and connected to the programming por t (CPU por t) or the
communication port (communication port) of a PLC.
Various devices can be monitored and PLC data changed via the
GOT screens. Several display screens are built-in to the GOT,
and additional personalized screens can be created by the user.
F940GOT-SWD-E
•
1.2 Dimensions and Each Part Name
R S 4 2 2
This manual has been written to be used by trained and competent personnel. The definition of such a
person or persons is as follows:
•
~ Indispensable manual
| Either manual is necessary.
… Refer if necessary, please.
Do not lay signal cables near high voltage power cables or allow them to share the same
trunking duct, otherwise, effects of noise or surge induction are likely to take please. Keep
a safe distance of more than 100 mm from these wires.
Operate touch switches on the display screen by hand.
DO NOT use excessive force, or attempt operate them with hard or pointed objects.
The tip of a screw driver, pen or similar object for example may break the screen.
R S 2 3 2 C
Guidelines for the Safety of the User and Protection of the
F94*GOT-*WD-E
•
JY992D74101
1 4 0 (5 .5 1 ")
1 3 0 (5 .1 2 ")
JY992D94201E
Note;
2 3 (0 .9 1 ")
Installation Manual
Description
This manual contains explanations for
installation and operating procedure of F9GT40UMB data transfer adapter.
4 8 .5 (1 .9 0 ")
F940GOT Series(F94*GOT-*WD-E)
F9GT-40UMB
Manual
Manual Number
1 2 0 (4 .7 2 ")
1 3 0 (5 .1 2 ")
Manual Name
Description
RS-422
RS-422 Port for connecting either a PLC (including1:N connection) or
communication (computer link) unit <9-pin D-sub>
RS232C
RS-232C port for connecting eirher a personal computer, printer, bar-code reader
or 1:N connection
<9-pin D-sub>
d) Mounting bracket and tightening bolt
f) Expansion interface
h) Communication cable
e) PM-20BL battery
g) DC power supply terminal (M3)
i) Packing seal
2. Specifications
2.1 General Specifications
Item
Operating Temperature
Specifications
0 ~ 50 °C (32 ~ 122 °F)
[With expansion module: 0 ~ 40 °C (32 ~ 104 °F)]
Storage Temperature
-20 ~ 60 °C (-4 ~ 140 °F)
Humidity
35 ~ 85% Relative Humidity, No condensation
Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive
amount of electroconductive dust particles and must be no direct
sunlight. (Same as for saving)
Vibration Resistance
- intermittent vibration
10 ~ 57 Hz: 0.075 mm Half Amplitude
57 ~ 150 Hz: 9.8 m/s2 Acceleration
Sweep Count for X, Y, Z: 10 times (80 min. in each direction)
Vibration Resistance
- Continuous vibration
10 ~ 57 Hz: 0.035 mm Half Amplitude
57 ~ 150 Hz: 4.9 m/s2 Acceleration
Sweep Count for X, Y, Z: 10 times (80 min in each direction)
Shock Resistance
147m/s2 Acceleration,
3 times in each direction X, Y, and Z
Noise Immunity
1000 Vp-p, 1micro second, 30 ~ 100 Hz, tested by noise simulator
Dielectric Withstand Voltage 500 V AC > 1 min, tested between power terminals and ground
Insulation Resistance
5 MΩ > at 500 V DC, tested between power terminals and ground
Ground
Grounding resistance of 100 Ω or less. (class D)
Protection
IP 65F
…
This manual contains text, diagrams and explanations which will guide the reader in the correct
installation, safe use and operation of the F94*GOT-*WD-E and should be read and understood before
attempting to install or use the unit. Further information can be found in the associated manuals list below.
Specifications are subject to change without notice
a) Any engineer using the product associated with this manual, should be of a competent nature,
trained and qualified to the local and national standards. These engineers should be fully aware of
all aspects of safety with regards to automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and qualified to
the local and national standards.
c) All operators of the completed equipment should be trained to use that product in a safe and
co-ordinated manner in compliance to established safety practices.
Note: The term ‘completed equipment’ refers to a third party constructed device which contains or uses
the product associated with this manual.
Note’s on the Symbols Used in this Manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the users personal safety and protect the integrity of equipment.
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property
damage.
Refer to the manual of the connected programmable controller for details concerning that unit.
1. Introduction
Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage
that may arise as a result of the installation or use of this equipment.
•
All examples and diagrams shown in this manual are intended only as an aid to understanding the
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the
product based on these illustrative examples.
•
Manual Name
F940GOT Series
| (F94*GOT-*WD-E)
Installation Manual
Manual Number
JY997D94201
JY992D09101
(separate volume)
Describes the operation and use of the GOTF900 Series graphic operation terminals and
GT Designer2.
GOT-F900 Series
Operation Manual
GOT-F900 Series
~ Hardware Manual
(connection diagram)
GOT-F900
~ OPERATION MANUAL
(describes GT Designer2)
~
|
|
GT Designer2 Version1
Operating Manual
GT Designer2 Version1
Reference Manual
Software Name
GOT-F900 and GOT-A900 Series (for Windows) screen creation software.
GT Designer
SW…D5C-GOTR-PACKE
(… indicates version)
GOT-F900 and GOT-A900 Series (for Windows) screen creation software.
SW1-A edition of SW1D5C-GOTR-PACKE or later
FX-PCS-DU/WIN-E
GOT-F900 Series (for Windows) screen creation software.
SW0PC-FXDU/WIN-E version 2.00 or later
Production Name
F940GOT-LWD-E
FX-50DU-CAB0
Description
Graphic operation terminal main unit
SWD: 8 colors
LWD: White and black
FX-50DU-CAB0/EN
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
FX-50DU-CAB0-**M
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight.
** M is cable length. 1M: 1m (3' 3"), 10M: 10m (32' 9"), 20M: 20m (65' 7"),
30M: 30m (98' 5")
QC30R2
Communication cable (GOT ↔ CPU port in Q series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
FX-232CAB-1
Data exchange cable (GOT ↔ Personal computer <9-pin D-sub>)
PM-20BL
Battery for Alarm history, sampling and current time data retertion.
JY992D98601
This manual contains explanations for
installation and operating procedure of F9GT40FMB data transfer adapter.
1 0 (0 .3 9 ")
i)
h )
2 4 V D C
-
F9GT-40PSC
Transparent protection sheet for F940GOT (5 pieces)
F9GT-40LTS
Backlight for F940GOT
F9GT-40UMB
Data transfer adapter
F9GT-40FMB
Data transfer adapter (Flash memory built in)
Caution
During abnormal communication (including cable breakages) when monitor is executed within
the GOT, communication between the GOT and programmable controller CPU is interrupted.
It is then impossible to operate switches or devices in the PLC through the GOT.
Communication and normal operation resumes when the GOT system is correctly configured.
DO NOT configure emergency stop or safety features to operate through the GOT, and be
sure that there is no adverse consequences in the event of a GOT - PLC communications
malfunction.
+
6 .5 (0 .2 5 ")
6 .5 (0 .2 5 ")
2 3 (0 .9 1 ") 2 3 (0 .9 1 ")
1 5 2 (5 .9 8 ")
a) Display
c) Communication ports
5 (0 .2 0 ")
b) Mounting bracket hole
Port
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight.
Cable length is 3m (9' 10").
Describes wiring and installation of the GOTF900 Series graphic operation terminals.
FX-PCS-DU/WIN-E
|
SOFTWARE MANUAL
e )
g )
1.1 Product Lists
JY992D94801
(separate volume)
JY992D68301
Describes the operation of FX-PCS-DU/WIN(included with the screen
E screen creation software.
creation software)
d )
5 7 (2 .2 4 ")
f )
FX-40DU-CAB-**M
Describes the specifications and setting of
object functions in GT Designer2 (SW*D5CGTD2-E).
1 0 (0 .3 9 ")
Version
GT Designer2
SW…D5C-GTD2-E
(… indicates version)
JY992D94701
(separate volume)
(PDF files on CD-ROM
included with product)
5 (0 .2 0 ")
1 6 2 (6 .3 8 ")
3) Display screens are created using the following software.
Communication cable (GOT ↔ CPU port in FX, FX2C, A or QnA series PLC)
The connector on the GOT side is wired straight.
** M is cable length. 10M: 10m (32' 9"), 20M: 20m (65' 7"), 30M: 30m (98' 5")
Describes the operation of GT Designer
Included with the screen
(SW*D5C-GOTR-PACKE) and data transfer to
creation software
the GOT-900 Series. (Refer to the help file)
F9GT-40FMB
User’s Manual
G O T
Describes the operation and use of the GOTF900 Series graphic operation terminals, GT
Designer and FX-PCS-DU/WIN-E.
(PDF files on CD-ROM
included with product)
b )
P O W E R
Communication cable (GOT ↔ CPU port in FX, FX2C, A or QnA series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
Describes the operation of GT Designer2
(SW*D5C-GTD2-E) and data transfer to the
GOT-900 Series.
c )
P r o g r a m m in g
p o rt
FX-40DU-CAB
GT Designer
|
Operating Manual
…
a )
2) PLC user programs can be downloaded, uploaded and
monitored using programming software GX-Developer or FX-PCS/WIN-E on a personal computer via
the GOT. Further information can be found in the GOT-F900 Series Operation Manual.
Description
Describes the specifications, wiring, and
installation of F940GOT Series graphic
operation terminal. (hardware)
MASS (Weight): 1 kg (2.2 lbs)
Mounting brackets, Tightening bolt (M3, 6 bolts),
Packing seal for dust and water resistance
P L C
1) The GOT can connect to MELSEC FX, A, QnA and Q PLCs
as well as a host of third party manufactured units. Further
information can be found in GOT-F900 Series Hardware
Manual.
Owing to the very great variety in possible application of this equipment, you must satisfy yourself as
to its suitability for your specific application.
Associated Manuals
Dimensions: mm (inches)
Accessory:
The F940GOT-*WD-E (hereafter called “GOT” or “F940GOT”) is
to be mounted on the face of a control panel or operations panel,
and connected to the programming por t (CPU por t) or the
communication port (communication port) of a PLC.
Various devices can be monitored and PLC data changed via the
GOT screens. Several display screens are built-in to the GOT,
and additional personalized screens can be created by the user.
F940GOT-SWD-E
•
1.2 Dimensions and Each Part Name
R S 4 2 2
This manual has been written to be used by trained and competent personnel. The definition of such a
person or persons is as follows:
•
~ Indispensable manual
| Either manual is necessary.
… Refer if necessary, please.
Do not lay signal cables near high voltage power cables or allow them to share the same
trunking duct, otherwise, effects of noise or surge induction are likely to take please. Keep
a safe distance of more than 100 mm from these wires.
Operate touch switches on the display screen by hand.
DO NOT use excessive force, or attempt operate them with hard or pointed objects.
The tip of a screw driver, pen or similar object for example may break the screen.
R S 2 3 2 C
Guidelines for the Safety of the User and Protection of the
F94*GOT-*WD-E
•
JY992D74101
1 4 0 (5 .5 1 ")
1 3 0 (5 .1 2 ")
JY992D94201E
Note;
2 3 (0 .9 1 ")
Installation Manual
Description
This manual contains explanations for
installation and operating procedure of F9GT40UMB data transfer adapter.
4 8 .5 (1 .9 0 ")
F940GOT Series(F94*GOT-*WD-E)
F9GT-40UMB
Manual
Manual Number
1 2 0 (4 .7 2 ")
1 3 0 (5 .1 2 ")
Manual Name
Description
RS-422
RS-422 Port for connecting either a PLC (including1:N connection) or
communication (computer link) unit <9-pin D-sub>
RS232C
RS-232C port for connecting eirher a personal computer, printer, bar-code reader
or 1:N connection
<9-pin D-sub>
d) Mounting bracket and tightening bolt
f) Expansion interface
h) Communication cable
e) PM-20BL battery
g) DC power supply terminal (M3)
i) Packing seal
2. Specifications
2.1 General Specifications
Item
Operating Temperature
Specifications
0 ~ 50 °C (32 ~ 122 °F)
[With expansion module: 0 ~ 40 °C (32 ~ 104 °F)]
Storage Temperature
-20 ~ 60 °C (-4 ~ 140 °F)
Humidity
35 ~ 85% Relative Humidity, No condensation
Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive
amount of electroconductive dust particles and must be no direct
sunlight. (Same as for saving)
Vibration Resistance
- intermittent vibration
10 ~ 57 Hz: 0.075 mm Half Amplitude
57 ~ 150 Hz: 9.8 m/s2 Acceleration
Sweep Count for X, Y, Z: 10 times (80 min. in each direction)
Vibration Resistance
- Continuous vibration
10 ~ 57 Hz: 0.035 mm Half Amplitude
57 ~ 150 Hz: 4.9 m/s2 Acceleration
Sweep Count for X, Y, Z: 10 times (80 min in each direction)
Shock Resistance
147m/s2 Acceleration,
3 times in each direction X, Y, and Z
Noise Immunity
1000 Vp-p, 1micro second, 30 ~ 100 Hz, tested by noise simulator
Dielectric Withstand Voltage 500 V AC > 1 min, tested between power terminals and ground
Insulation Resistance
5 MΩ > at 500 V DC, tested between power terminals and ground
Ground
Grounding resistance of 100 Ω or less. (class D)
Protection
IP 65F
2.2 Power Supply Specifications
Items
F94*GOT-SWD-E
Power Supply Voltage
24V DC, +10% -15%
Power Supply Ripple
200 mV or less
F94*GOT-LWD-E
b) GOT
Ratings: 390 mA at 24V DC
Cautions:
Fuse built-in GOT (impossible to change)
Max. Allowable Momentary
Power Supply Failure period
5 ms; If less than 5 ms, the GOT will continue operation. If 5 ms or
more, the GOT will shut down.
Battery
Built-in, PM-20BL type lithium battery. (Approximately 5 years
battery life)
c)
2.3 Screen Hardware Specifications
F94*GOT-SWD-E
a) Clamping bolt
F94*GOT-LWD-E
STN colours liquid crystal
Resolution
320 × 240 (dot), 40 characters × 15 lines
Dot Pitch
0.36 mm (0.014") Horizontal × 0.36 mm (0.014") Vertical.
Effective Display Size
115 mm (4.53") × 86 mm (3.39"); 6 (5.7 inch) type
Number of Colours
8 colours
Life of liquid crystal
Approximately 50,000 hours
(Operating temperature: 25 °C / 77°F)
Backlight
Cold cathode tube
Life of Backlight
40,000 hours or more
(Operating temperature: 25 °C / 77°F)
Touch Keys
Maximum 50 touch keys / screen, 20 × 12 matrix
RS-422
RS-232C 1channel
1 7 2 (6 .7 7 ")
5 7 (2 .2 4 ")
b) Packing seal
When the same screen is displayed for a long time, an incidental color or partial discoloration is
generated on the screen due to heat damage, and it may not disappear.
•
Using the GOT Backlight OFF function can prolong the life of the backlight.
For details on the Backlight OFF function, refer to the following.
GOT-F900 Series OPERATION MANUAL/GOT-F900 Series OPERATION MANUAL [GT Designer2
Version]
3. Installation
+
5 ( 0 .2 0 " ) o r le s s
b )
Do not mount the GOT in an environment that contains dust, soot corrosive or conducive
dust, corrosive or flammable gas, or expose the unit to high temperatures, dew
condensation, direct sunlight, rain, wind or impact and vibration.
If the GOT is used in such a place, electrical shock, fire, malfunction, damages or
deterioration may occur.
Never drop cutting chips or electric wire chips into the ventilation window of the GOT
when drilling screw holes or performing wiring. Such chips may cause fire, failure or
malfunction.
Turn off the power before securely connecting any cables. Poor connection may cause
malfunction.
2) Remove the existing battery from the battery holder, and
disconnect.
1 5 3 ( 6 .0 2 " ) + 1 (+ 0 .0 4 ")
0
4) Insert the new battery into the battery holder, and attach the
cover.
Note:
•
Wire the power supply using electric wires of 0.75 mm2 or more so that voltage drop will
not occur. Use M3 size crimp style terminals. Securely tighten crimp-style terminals with a
torque of 0.5 ~ 0.8 N‚m so that errors can be avoided.
•
Insure correct termination of the DC power source, incorrect connection may result in unit
failure or serious damage to the GOT being burnt.
•
Attach a fuse of 2 A to the 24V DC power supply.
•
Perform Class D (100Ω or less) grounding with an electric wire of at least 1.25 mm2.
Never perform common grounding of the GOT and a strong power system.
6.2 Backlight Replacement
Replace the backlight F9GT-40LTS using the following procedure.
Note: Removing Rear Panel
If the rear panel is pulled using an excessive force, the cable connecting the rear panel and
the front panel may be disconnected or the PCB may be damaged. Be careful.
6.2.1 Replacement procedure
a )
Note
•
Use an external power supply to provide 24V DC.
(The service power supply of the programmable controller cannot be used.)
•
Even if instantaneous power interruption of less than 5 ms occurs, the GOT continues to
operate. When power interruption for considerable period of time or voltage drop occurs,
the GOT stops its operation. However, when the power supply is recovered, the GOT
automatically restar ts its operation. (The screen displayed just after recovery is
determined by the working environment originally set.)
Grounding resistance
100Ω or less (class D)
24V DC external
power supply
1 2 1 + 01
( 4 . 7 6 " + 00 . 0 4 " )
Fuse (2A)
24V DC
PLC
1)Make sure that the power of the GOT is turned OFF.
Remove the mounting screws (a) located at 4 corners, and
slowly remove the rear panel.
2)Disconnect the backlight connector (b).
3)Remove the backlight F9GT-40LTS (c) from the backlight
fixing holder (d).
It is recommended to insert a screwdriver into the holder.
Then, the backlight can be taken out easily.
d )
c )
b )
4)Attach a new backlight F9GT-40LTS (c). Put it into the GOT
by performing the steps 1) ~ 3) in the reverse order.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi;
opportunity loss or lost profits caused by faults in the Mitsubishi products; damage, secondary damage,
accident compensation caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For the detailed warranty, refer to the GOT-F900 Series HARDWARE MANUAL [CONNECTION].
GOT
Manual number : JY992D94201
5. Expansion Module
Note
Make sure that the thickness of the panel surface is no more than 5 mm (0.20").
3) Within 30 seconds, connect a new battery.
Cut OFF all external phases of power before installation or wiring to avoid electric shock or
serious damage to the product.
U n it: m m ( in c h e s )
S lo t to b e c u t o n p a n e l
1) Turn off the power to the GOT and remove the battery holder
cover.
Caution:
The GOT is designed to be mounted in a panel. Install it using the following procedure:
1) Preparing the panel surface.
On the panel surface, cut a rectangular mounting slot of the
dimensions shown on the right.
At this time, space of 10 mm is required at each of the top
and the bottom of the slot, inside the panel for metal fixtures
as shown in “4) Dimensions required inside the panel for
installation”.
6.1.1 Replacement Procedure
4. Power Supply Wiring
Note;
•
For approximately one month after the control device for battery voltage drop turns ON, the
battery will back up the alarm history, sampling and the current time. When the control device
(system information) turns ON, replace the battery (PM-20BL) as soon as possible.
The screen data is stored in the flash memory. Even if the battery is totally worn out, the screen
data will remaven after severe battery voltage loss.
PM-20BL
•
•
Never disassemble or modify the GOT. Disassembly or modification may cause failure,
malfunction or fire. For repair, please, contact a service representative.
Note:
a )
Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel. It is
impossible to completely avoid this symptom, as the liquid crystal display comprises of a great
number of display elements.
Flickers may be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not caused by product defect.
•
•
When the battery voltage drops, a control device (system information) set by the screen design software
turns ON. The control device interlocks with an auxiliary relay in the PLC. It is recommended to provide a
lamp while utilizing the output of the PLC so that voltage drop can be monitored outside the GOT.
For details of control devices, refer to the GOT-F900 Series Operation Manual.
2 4 V D C
Flash memory 512 KB (built-in)
Always power OFF and remove the GOT from the panel before starting replacement of
the backlight and battery. If this is not the case, the backlight may be dropped and cause
injury, or electrical shock sustained.
6.1 Battery Replacement
4) Dimensions required inside the panel for
installation.
When installing the GOT, make sure that
the inner dimensions shown on the right
are available.
-
User Memory
•
When repairing liquid crystal screen, please, contact a service representative.
1channel
User screen: 500 screens or less
System screen: Allocated screens No. 1001-1030.
Correctly connect the battery for memory backup. Never charge, disassemble, heat, burn
or short-circuit the battery. If the battery is handled in such a way, or fire may be caused.
Turn OFF the power, before connecting/disconnecting cables.
Connecting/disconnecting cables while the power is turned on will cause failure or
malfunction caused.
Make sure to tighten the clamping bolts with a torque of 0.3 ~ 0.5 N‚m.
a) PLC connection cable
Number of Screens
•
Note:
Note:
White and Black
RS-232C
a )
b )
b) Mounting bracket
Display Device
RS-422
3) Fixing the GOT
Put hooks of the mounting brackets (supplied) in to the
mounting holes of the GOT. Tighten mounting bolts (also
supplied) until the GOT is securely fixed.
Fix mounting bolts in all four positions, above and below the
GOT.
1 4 0 (5 .5 1 ")
Items
•
6. Maintenance
c) Mounting slot
180 mA at 24 V DC when backlight is turned OFF
Fuse
Interface
a)
b) F9GT-40FMB
F9GT-40FMB has a built-in flash memory and can transfer screen data when installed in the GOT.
(When installed in OS versions either than 6.40, screen display is not available while transferring data
from F9GT-40FMB to the GOT.)
For operating procedures and specifications, refer to the manual for F9GT-40FMB.
b)
a) Packing seal
Ratings: 410 mA at 24V DC
Current Consumption
2) Inserting the GOT into the panel surface
Attach the packing seal to the GOT, and insert the GOT
from the front face of the panel surface.
a) F9GT-40UMB
The data transfer adaptor F9GT-40UMB is used to store the user screen data in the EPROM for user
screen data FX-EPROM-4M to the flush memory in the GOT. (The user screen data can be written to
the EPROM using the screen design software.)
This adaptor is useful when the same screen data is transferred to two or more GOT units.
For the operating procedure of F9GT-40UMB, please see the manual of F9GT-40UMB.
Manual revision : E
Date
: Sep. 2008
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN
2.2 Power Supply Specifications
Items
F94*GOT-SWD-E
Power Supply Voltage
24V DC, +10% -15%
Power Supply Ripple
200 mV or less
F94*GOT-LWD-E
b) GOT
Ratings: 390 mA at 24V DC
Cautions:
Fuse built-in GOT (impossible to change)
Max. Allowable Momentary
Power Supply Failure period
5 ms; If less than 5 ms, the GOT will continue operation. If 5 ms or
more, the GOT will shut down.
Battery
Built-in, PM-20BL type lithium battery. (Approximately 5 years
battery life)
c)
2.3 Screen Hardware Specifications
F94*GOT-SWD-E
a) Clamping bolt
F94*GOT-LWD-E
STN colours liquid crystal
Resolution
320 × 240 (dot), 40 characters × 15 lines
Dot Pitch
0.36 mm (0.014") Horizontal × 0.36 mm (0.014") Vertical.
Effective Display Size
115 mm (4.53") × 86 mm (3.39"); 6 (5.7 inch) type
Number of Colours
8 colours
Life of liquid crystal
Approximately 50,000 hours
(Operating temperature: 25 °C / 77°F)
Backlight
Cold cathode tube
Life of Backlight
40,000 hours or more
(Operating temperature: 25 °C / 77°F)
Touch Keys
Maximum 50 touch keys / screen, 20 × 12 matrix
RS-422
RS-232C 1channel
1 7 2 (6 .7 7 ")
5 7 (2 .2 4 ")
b) Packing seal
When the same screen is displayed for a long time, an incidental color or partial discoloration is
generated on the screen due to heat damage, and it may not disappear.
•
Using the GOT Backlight OFF function can prolong the life of the backlight.
For details on the Backlight OFF function, refer to the following.
GOT-F900 Series OPERATION MANUAL/GOT-F900 Series OPERATION MANUAL [GT Designer2
Version]
3. Installation
+
5 ( 0 .2 0 " ) o r le s s
b )
Do not mount the GOT in an environment that contains dust, soot corrosive or conducive
dust, corrosive or flammable gas, or expose the unit to high temperatures, dew
condensation, direct sunlight, rain, wind or impact and vibration.
If the GOT is used in such a place, electrical shock, fire, malfunction, damages or
deterioration may occur.
Never drop cutting chips or electric wire chips into the ventilation window of the GOT
when drilling screw holes or performing wiring. Such chips may cause fire, failure or
malfunction.
Turn off the power before securely connecting any cables. Poor connection may cause
malfunction.
2) Remove the existing battery from the battery holder, and
disconnect.
1 5 3 ( 6 .0 2 " ) + 1 (+ 0 .0 4 ")
0
4) Insert the new battery into the battery holder, and attach the
cover.
Note:
•
Wire the power supply using electric wires of 0.75 mm2 or more so that voltage drop will
not occur. Use M3 size crimp style terminals. Securely tighten crimp-style terminals with a
torque of 0.5 ~ 0.8 N‚m so that errors can be avoided.
•
Insure correct termination of the DC power source, incorrect connection may result in unit
failure or serious damage to the GOT being burnt.
•
Attach a fuse of 2 A to the 24V DC power supply.
•
Perform Class D (100Ω or less) grounding with an electric wire of at least 1.25 mm2.
Never perform common grounding of the GOT and a strong power system.
6.2 Backlight Replacement
Replace the backlight F9GT-40LTS using the following procedure.
Note: Removing Rear Panel
If the rear panel is pulled using an excessive force, the cable connecting the rear panel and
the front panel may be disconnected or the PCB may be damaged. Be careful.
6.2.1 Replacement procedure
a )
Note
•
Use an external power supply to provide 24V DC.
(The service power supply of the programmable controller cannot be used.)
•
Even if instantaneous power interruption of less than 5 ms occurs, the GOT continues to
operate. When power interruption for considerable period of time or voltage drop occurs,
the GOT stops its operation. However, when the power supply is recovered, the GOT
automatically restar ts its operation. (The screen displayed just after recovery is
determined by the working environment originally set.)
Grounding resistance
100Ω or less (class D)
24V DC external
power supply
1 2 1 + 01
( 4 . 7 6 " + 00 . 0 4 " )
Fuse (2A)
24V DC
PLC
1)Make sure that the power of the GOT is turned OFF.
Remove the mounting screws (a) located at 4 corners, and
slowly remove the rear panel.
2)Disconnect the backlight connector (b).
3)Remove the backlight F9GT-40LTS (c) from the backlight
fixing holder (d).
It is recommended to insert a screwdriver into the holder.
Then, the backlight can be taken out easily.
d )
c )
b )
4)Attach a new backlight F9GT-40LTS (c). Put it into the GOT
by performing the steps 1) ~ 3) in the reverse order.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi;
opportunity loss or lost profits caused by faults in the Mitsubishi products; damage, secondary damage,
accident compensation caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For the detailed warranty, refer to the GOT-F900 Series HARDWARE MANUAL [CONNECTION].
GOT
Manual number : JY992D94201
5. Expansion Module
Note
Make sure that the thickness of the panel surface is no more than 5 mm (0.20").
3) Within 30 seconds, connect a new battery.
Cut OFF all external phases of power before installation or wiring to avoid electric shock or
serious damage to the product.
U n it: m m ( in c h e s )
S lo t to b e c u t o n p a n e l
1) Turn off the power to the GOT and remove the battery holder
cover.
Caution:
The GOT is designed to be mounted in a panel. Install it using the following procedure:
1) Preparing the panel surface.
On the panel surface, cut a rectangular mounting slot of the
dimensions shown on the right.
At this time, space of 10 mm is required at each of the top
and the bottom of the slot, inside the panel for metal fixtures
as shown in “4) Dimensions required inside the panel for
installation”.
6.1.1 Replacement Procedure
4. Power Supply Wiring
Note;
•
For approximately one month after the control device for battery voltage drop turns ON, the
battery will back up the alarm history, sampling and the current time. When the control device
(system information) turns ON, replace the battery (PM-20BL) as soon as possible.
The screen data is stored in the flash memory. Even if the battery is totally worn out, the screen
data will remaven after severe battery voltage loss.
PM-20BL
•
•
Never disassemble or modify the GOT. Disassembly or modification may cause failure,
malfunction or fire. For repair, please, contact a service representative.
Note:
a )
Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel. It is
impossible to completely avoid this symptom, as the liquid crystal display comprises of a great
number of display elements.
Flickers may be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not caused by product defect.
•
•
When the battery voltage drops, a control device (system information) set by the screen design software
turns ON. The control device interlocks with an auxiliary relay in the PLC. It is recommended to provide a
lamp while utilizing the output of the PLC so that voltage drop can be monitored outside the GOT.
For details of control devices, refer to the GOT-F900 Series Operation Manual.
2 4 V D C
Flash memory 512 KB (built-in)
Always power OFF and remove the GOT from the panel before starting replacement of
the backlight and battery. If this is not the case, the backlight may be dropped and cause
injury, or electrical shock sustained.
6.1 Battery Replacement
4) Dimensions required inside the panel for
installation.
When installing the GOT, make sure that
the inner dimensions shown on the right
are available.
-
User Memory
•
When repairing liquid crystal screen, please, contact a service representative.
1channel
User screen: 500 screens or less
System screen: Allocated screens No. 1001-1030.
Correctly connect the battery for memory backup. Never charge, disassemble, heat, burn
or short-circuit the battery. If the battery is handled in such a way, or fire may be caused.
Turn OFF the power, before connecting/disconnecting cables.
Connecting/disconnecting cables while the power is turned on will cause failure or
malfunction caused.
Make sure to tighten the clamping bolts with a torque of 0.3 ~ 0.5 N‚m.
a) PLC connection cable
Number of Screens
•
Note:
Note:
White and Black
RS-232C
a )
b )
b) Mounting bracket
Display Device
RS-422
3) Fixing the GOT
Put hooks of the mounting brackets (supplied) in to the
mounting holes of the GOT. Tighten mounting bolts (also
supplied) until the GOT is securely fixed.
Fix mounting bolts in all four positions, above and below the
GOT.
1 4 0 (5 .5 1 ")
Items
•
6. Maintenance
c) Mounting slot
180 mA at 24 V DC when backlight is turned OFF
Fuse
Interface
a)
b) F9GT-40FMB
F9GT-40FMB has a built-in flash memory and can transfer screen data when installed in the GOT.
(When installed in OS versions either than 6.40, screen display is not available while transferring data
from F9GT-40FMB to the GOT.)
For operating procedures and specifications, refer to the manual for F9GT-40FMB.
b)
a) Packing seal
Ratings: 410 mA at 24V DC
Current Consumption
2) Inserting the GOT into the panel surface
Attach the packing seal to the GOT, and insert the GOT
from the front face of the panel surface.
a) F9GT-40UMB
The data transfer adaptor F9GT-40UMB is used to store the user screen data in the EPROM for user
screen data FX-EPROM-4M to the flush memory in the GOT. (The user screen data can be written to
the EPROM using the screen design software.)
This adaptor is useful when the same screen data is transferred to two or more GOT units.
For the operating procedure of F9GT-40UMB, please see the manual of F9GT-40UMB.
Manual revision : E
Date
: Sep. 2008
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN
2.2 Power Supply Specifications
Items
F94*GOT-SWD-E
Power Supply Voltage
24V DC, +10% -15%
Power Supply Ripple
200 mV or less
F94*GOT-LWD-E
b) GOT
Ratings: 390 mA at 24V DC
Cautions:
Fuse built-in GOT (impossible to change)
Max. Allowable Momentary
Power Supply Failure period
5 ms; If less than 5 ms, the GOT will continue operation. If 5 ms or
more, the GOT will shut down.
Battery
Built-in, PM-20BL type lithium battery. (Approximately 5 years
battery life)
c)
2.3 Screen Hardware Specifications
F94*GOT-SWD-E
a) Clamping bolt
F94*GOT-LWD-E
STN colours liquid crystal
Resolution
320 × 240 (dot), 40 characters × 15 lines
Dot Pitch
0.36 mm (0.014") Horizontal × 0.36 mm (0.014") Vertical.
Effective Display Size
115 mm (4.53") × 86 mm (3.39"); 6 (5.7 inch) type
Number of Colours
8 colours
Life of liquid crystal
Approximately 50,000 hours
(Operating temperature: 25 °C / 77°F)
Backlight
Cold cathode tube
Life of Backlight
40,000 hours or more
(Operating temperature: 25 °C / 77°F)
Touch Keys
Maximum 50 touch keys / screen, 20 × 12 matrix
RS-422
RS-232C 1channel
1 7 2 (6 .7 7 ")
5 7 (2 .2 4 ")
b) Packing seal
When the same screen is displayed for a long time, an incidental color or partial discoloration is
generated on the screen due to heat damage, and it may not disappear.
•
Using the GOT Backlight OFF function can prolong the life of the backlight.
For details on the Backlight OFF function, refer to the following.
GOT-F900 Series OPERATION MANUAL/GOT-F900 Series OPERATION MANUAL [GT Designer2
Version]
3. Installation
+
5 ( 0 .2 0 " ) o r le s s
b )
Do not mount the GOT in an environment that contains dust, soot corrosive or conducive
dust, corrosive or flammable gas, or expose the unit to high temperatures, dew
condensation, direct sunlight, rain, wind or impact and vibration.
If the GOT is used in such a place, electrical shock, fire, malfunction, damages or
deterioration may occur.
Never drop cutting chips or electric wire chips into the ventilation window of the GOT
when drilling screw holes or performing wiring. Such chips may cause fire, failure or
malfunction.
Turn off the power before securely connecting any cables. Poor connection may cause
malfunction.
2) Remove the existing battery from the battery holder, and
disconnect.
1 5 3 ( 6 .0 2 " ) + 1 (+ 0 .0 4 ")
0
4) Insert the new battery into the battery holder, and attach the
cover.
Note:
•
Wire the power supply using electric wires of 0.75 mm2 or more so that voltage drop will
not occur. Use M3 size crimp style terminals. Securely tighten crimp-style terminals with a
torque of 0.5 ~ 0.8 N‚m so that errors can be avoided.
•
Insure correct termination of the DC power source, incorrect connection may result in unit
failure or serious damage to the GOT being burnt.
•
Attach a fuse of 2 A to the 24V DC power supply.
•
Perform Class D (100Ω or less) grounding with an electric wire of at least 1.25 mm2.
Never perform common grounding of the GOT and a strong power system.
6.2 Backlight Replacement
Replace the backlight F9GT-40LTS using the following procedure.
Note: Removing Rear Panel
If the rear panel is pulled using an excessive force, the cable connecting the rear panel and
the front panel may be disconnected or the PCB may be damaged. Be careful.
6.2.1 Replacement procedure
a )
Note
•
Use an external power supply to provide 24V DC.
(The service power supply of the programmable controller cannot be used.)
•
Even if instantaneous power interruption of less than 5 ms occurs, the GOT continues to
operate. When power interruption for considerable period of time or voltage drop occurs,
the GOT stops its operation. However, when the power supply is recovered, the GOT
automatically restar ts its operation. (The screen displayed just after recovery is
determined by the working environment originally set.)
Grounding resistance
100Ω or less (class D)
24V DC external
power supply
1 2 1 + 01
( 4 . 7 6 " + 00 . 0 4 " )
Fuse (2A)
24V DC
PLC
1)Make sure that the power of the GOT is turned OFF.
Remove the mounting screws (a) located at 4 corners, and
slowly remove the rear panel.
2)Disconnect the backlight connector (b).
3)Remove the backlight F9GT-40LTS (c) from the backlight
fixing holder (d).
It is recommended to insert a screwdriver into the holder.
Then, the backlight can be taken out easily.
d )
c )
b )
4)Attach a new backlight F9GT-40LTS (c). Put it into the GOT
by performing the steps 1) ~ 3) in the reverse order.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi;
opportunity loss or lost profits caused by faults in the Mitsubishi products; damage, secondary damage,
accident compensation caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For the detailed warranty, refer to the GOT-F900 Series HARDWARE MANUAL [CONNECTION].
GOT
Manual number : JY992D94201
5. Expansion Module
Note
Make sure that the thickness of the panel surface is no more than 5 mm (0.20").
3) Within 30 seconds, connect a new battery.
Cut OFF all external phases of power before installation or wiring to avoid electric shock or
serious damage to the product.
U n it: m m ( in c h e s )
S lo t to b e c u t o n p a n e l
1) Turn off the power to the GOT and remove the battery holder
cover.
Caution:
The GOT is designed to be mounted in a panel. Install it using the following procedure:
1) Preparing the panel surface.
On the panel surface, cut a rectangular mounting slot of the
dimensions shown on the right.
At this time, space of 10 mm is required at each of the top
and the bottom of the slot, inside the panel for metal fixtures
as shown in “4) Dimensions required inside the panel for
installation”.
6.1.1 Replacement Procedure
4. Power Supply Wiring
Note;
•
For approximately one month after the control device for battery voltage drop turns ON, the
battery will back up the alarm history, sampling and the current time. When the control device
(system information) turns ON, replace the battery (PM-20BL) as soon as possible.
The screen data is stored in the flash memory. Even if the battery is totally worn out, the screen
data will remaven after severe battery voltage loss.
PM-20BL
•
•
Never disassemble or modify the GOT. Disassembly or modification may cause failure,
malfunction or fire. For repair, please, contact a service representative.
Note:
a )
Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel. It is
impossible to completely avoid this symptom, as the liquid crystal display comprises of a great
number of display elements.
Flickers may be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not caused by product defect.
•
•
When the battery voltage drops, a control device (system information) set by the screen design software
turns ON. The control device interlocks with an auxiliary relay in the PLC. It is recommended to provide a
lamp while utilizing the output of the PLC so that voltage drop can be monitored outside the GOT.
For details of control devices, refer to the GOT-F900 Series Operation Manual.
2 4 V D C
Flash memory 512 KB (built-in)
Always power OFF and remove the GOT from the panel before starting replacement of
the backlight and battery. If this is not the case, the backlight may be dropped and cause
injury, or electrical shock sustained.
6.1 Battery Replacement
4) Dimensions required inside the panel for
installation.
When installing the GOT, make sure that
the inner dimensions shown on the right
are available.
-
User Memory
•
When repairing liquid crystal screen, please, contact a service representative.
1channel
User screen: 500 screens or less
System screen: Allocated screens No. 1001-1030.
Correctly connect the battery for memory backup. Never charge, disassemble, heat, burn
or short-circuit the battery. If the battery is handled in such a way, or fire may be caused.
Turn OFF the power, before connecting/disconnecting cables.
Connecting/disconnecting cables while the power is turned on will cause failure or
malfunction caused.
Make sure to tighten the clamping bolts with a torque of 0.3 ~ 0.5 N‚m.
a) PLC connection cable
Number of Screens
•
Note:
Note:
White and Black
RS-232C
a )
b )
b) Mounting bracket
Display Device
RS-422
3) Fixing the GOT
Put hooks of the mounting brackets (supplied) in to the
mounting holes of the GOT. Tighten mounting bolts (also
supplied) until the GOT is securely fixed.
Fix mounting bolts in all four positions, above and below the
GOT.
1 4 0 (5 .5 1 ")
Items
•
6. Maintenance
c) Mounting slot
180 mA at 24 V DC when backlight is turned OFF
Fuse
Interface
a)
b) F9GT-40FMB
F9GT-40FMB has a built-in flash memory and can transfer screen data when installed in the GOT.
(When installed in OS versions either than 6.40, screen display is not available while transferring data
from F9GT-40FMB to the GOT.)
For operating procedures and specifications, refer to the manual for F9GT-40FMB.
b)
a) Packing seal
Ratings: 410 mA at 24V DC
Current Consumption
2) Inserting the GOT into the panel surface
Attach the packing seal to the GOT, and insert the GOT
from the front face of the panel surface.
a) F9GT-40UMB
The data transfer adaptor F9GT-40UMB is used to store the user screen data in the EPROM for user
screen data FX-EPROM-4M to the flush memory in the GOT. (The user screen data can be written to
the EPROM using the screen design software.)
This adaptor is useful when the same screen data is transferred to two or more GOT units.
For the operating procedure of F9GT-40UMB, please see the manual of F9GT-40UMB.
Manual revision : E
Date
: Sep. 2008
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN
…
This manual contains text, diagrams and explanations which will guide the reader in the correct
installation, safe use and operation of the F94*GOT-*WD-E and should be read and understood before
attempting to install or use the unit. Further information can be found in the associated manuals list below.
Specifications are subject to change without notice
a) Any engineer using the product associated with this manual, should be of a competent nature,
trained and qualified to the local and national standards. These engineers should be fully aware of
all aspects of safety with regards to automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and qualified to
the local and national standards.
c) All operators of the completed equipment should be trained to use that product in a safe and
co-ordinated manner in compliance to established safety practices.
Note: The term ‘completed equipment’ refers to a third party constructed device which contains or uses
the product associated with this manual.
Note’s on the Symbols Used in this Manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the users personal safety and protect the integrity of equipment.
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property
damage.
Refer to the manual of the connected programmable controller for details concerning that unit.
1. Introduction
Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage
that may arise as a result of the installation or use of this equipment.
•
All examples and diagrams shown in this manual are intended only as an aid to understanding the
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the
product based on these illustrative examples.
•
Manual Name
F940GOT Series
| (F94*GOT-*WD-E)
Installation Manual
Manual Number
JY997D94201
JY992D09101
(separate volume)
Describes the operation and use of the GOTF900 Series graphic operation terminals and
GT Designer2.
GOT-F900 Series
Operation Manual
GOT-F900 Series
~ Hardware Manual
(connection diagram)
GOT-F900
~ OPERATION MANUAL
(describes GT Designer2)
~
|
|
GT Designer2 Version1
Operating Manual
GT Designer2 Version1
Reference Manual
Software Name
GOT-F900 and GOT-A900 Series (for Windows) screen creation software.
GT Designer
SW…D5C-GOTR-PACKE
(… indicates version)
GOT-F900 and GOT-A900 Series (for Windows) screen creation software.
SW1-A edition of SW1D5C-GOTR-PACKE or later
FX-PCS-DU/WIN-E
GOT-F900 Series (for Windows) screen creation software.
SW0PC-FXDU/WIN-E version 2.00 or later
Production Name
F940GOT-LWD-E
FX-50DU-CAB0
Description
Graphic operation terminal main unit
SWD: 8 colors
LWD: White and black
FX-50DU-CAB0/EN
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
FX-50DU-CAB0-**M
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight.
** M is cable length. 1M: 1m (3' 3"), 10M: 10m (32' 9"), 20M: 20m (65' 7"),
30M: 30m (98' 5")
QC30R2
Communication cable (GOT ↔ CPU port in Q series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
FX-232CAB-1
Data exchange cable (GOT ↔ Personal computer <9-pin D-sub>)
PM-20BL
Battery for Alarm history, sampling and current time data retertion.
JY992D98601
This manual contains explanations for
installation and operating procedure of F9GT40FMB data transfer adapter.
1 0 (0 .3 9 ")
i)
h )
2 4 V D C
-
F9GT-40PSC
Transparent protection sheet for F940GOT (5 pieces)
F9GT-40LTS
Backlight for F940GOT
F9GT-40UMB
Data transfer adapter
F9GT-40FMB
Data transfer adapter (Flash memory built in)
Caution
During abnormal communication (including cable breakages) when monitor is executed within
the GOT, communication between the GOT and programmable controller CPU is interrupted.
It is then impossible to operate switches or devices in the PLC through the GOT.
Communication and normal operation resumes when the GOT system is correctly configured.
DO NOT configure emergency stop or safety features to operate through the GOT, and be
sure that there is no adverse consequences in the event of a GOT - PLC communications
malfunction.
+
6 .5 (0 .2 5 ")
6 .5 (0 .2 5 ")
2 3 (0 .9 1 ") 2 3 (0 .9 1 ")
1 5 2 (5 .9 8 ")
a) Display
c) Communication ports
5 (0 .2 0 ")
b) Mounting bracket hole
Port
Communication cable (GOT ↔ CPU port in FX0, FX0S, FX1S, FX0N, FX1N, FX2N
or FX2NC series PLC)
The connector on the GOT side is wired straight.
Cable length is 3m (9' 10").
Describes wiring and installation of the GOTF900 Series graphic operation terminals.
FX-PCS-DU/WIN-E
|
SOFTWARE MANUAL
e )
g )
1.1 Product Lists
JY992D94801
(separate volume)
JY992D68301
Describes the operation of FX-PCS-DU/WIN(included with the screen
E screen creation software.
creation software)
d )
5 7 (2 .2 4 ")
f )
FX-40DU-CAB-**M
Describes the specifications and setting of
object functions in GT Designer2 (SW*D5CGTD2-E).
1 0 (0 .3 9 ")
Version
GT Designer2
SW…D5C-GTD2-E
(… indicates version)
JY992D94701
(separate volume)
(PDF files on CD-ROM
included with product)
5 (0 .2 0 ")
1 6 2 (6 .3 8 ")
3) Display screens are created using the following software.
Communication cable (GOT ↔ CPU port in FX, FX2C, A or QnA series PLC)
The connector on the GOT side is wired straight.
** M is cable length. 10M: 10m (32' 9"), 20M: 20m (65' 7"), 30M: 30m (98' 5")
Describes the operation of GT Designer
Included with the screen
(SW*D5C-GOTR-PACKE) and data transfer to
creation software
the GOT-900 Series. (Refer to the help file)
F9GT-40FMB
User’s Manual
G O T
Describes the operation and use of the GOTF900 Series graphic operation terminals, GT
Designer and FX-PCS-DU/WIN-E.
(PDF files on CD-ROM
included with product)
b )
P O W E R
Communication cable (GOT ↔ CPU port in FX, FX2C, A or QnA series PLC)
The connector on the GOT side is wired straight. Cable length is 3m (9' 10").
Describes the operation of GT Designer2
(SW*D5C-GTD2-E) and data transfer to the
GOT-900 Series.
c )
P r o g r a m m in g
p o rt
FX-40DU-CAB
GT Designer
|
Operating Manual
…
a )
2) PLC user programs can be downloaded, uploaded and
monitored using programming software GX-Developer or FX-PCS/WIN-E on a personal computer via
the GOT. Further information can be found in the GOT-F900 Series Operation Manual.
Description
Describes the specifications, wiring, and
installation of F940GOT Series graphic
operation terminal. (hardware)
MASS (Weight): 1 kg (2.2 lbs)
Mounting brackets, Tightening bolt (M3, 6 bolts),
Packing seal for dust and water resistance
P L C
1) The GOT can connect to MELSEC FX, A, QnA and Q PLCs
as well as a host of third party manufactured units. Further
information can be found in GOT-F900 Series Hardware
Manual.
Owing to the very great variety in possible application of this equipment, you must satisfy yourself as
to its suitability for your specific application.
Associated Manuals
Dimensions: mm (inches)
Accessory:
The F940GOT-*WD-E (hereafter called “GOT” or “F940GOT”) is
to be mounted on the face of a control panel or operations panel,
and connected to the programming por t (CPU por t) or the
communication port (communication port) of a PLC.
Various devices can be monitored and PLC data changed via the
GOT screens. Several display screens are built-in to the GOT,
and additional personalized screens can be created by the user.
F940GOT-SWD-E
•
1.2 Dimensions and Each Part Name
R S 4 2 2
This manual has been written to be used by trained and competent personnel. The definition of such a
person or persons is as follows:
•
~ Indispensable manual
| Either manual is necessary.
… Refer if necessary, please.
Do not lay signal cables near high voltage power cables or allow them to share the same
trunking duct, otherwise, effects of noise or surge induction are likely to take please. Keep
a safe distance of more than 100 mm from these wires.
Operate touch switches on the display screen by hand.
DO NOT use excessive force, or attempt operate them with hard or pointed objects.
The tip of a screw driver, pen or similar object for example may break the screen.
R S 2 3 2 C
Guidelines for the Safety of the User and Protection of the
F94*GOT-*WD-E
•
JY992D74101
1 4 0 (5 .5 1 ")
1 3 0 (5 .1 2 ")
JY992D94201E
Note;
2 3 (0 .9 1 ")
Installation Manual
Description
This manual contains explanations for
installation and operating procedure of F9GT40UMB data transfer adapter.
4 8 .5 (1 .9 0 ")
F940GOT Series(F94*GOT-*WD-E)
F9GT-40UMB
Manual
Manual Number
1 2 0 (4 .7 2 ")
1 3 0 (5 .1 2 ")
Manual Name
Description
RS-422
RS-422 Port for connecting either a PLC (including1:N connection) or
communication (computer link) unit <9-pin D-sub>
RS232C
RS-232C port for connecting eirher a personal computer, printer, bar-code reader
or 1:N connection
<9-pin D-sub>
d) Mounting bracket and tightening bolt
f) Expansion interface
h) Communication cable
e) PM-20BL battery
g) DC power supply terminal (M3)
i) Packing seal
2. Specifications
2.1 General Specifications
Item
Operating Temperature
Specifications
0 ~ 50 °C (32 ~ 122 °F)
[With expansion module: 0 ~ 40 °C (32 ~ 104 °F)]
Storage Temperature
-20 ~ 60 °C (-4 ~ 140 °F)
Humidity
35 ~ 85% Relative Humidity, No condensation
Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive
amount of electroconductive dust particles and must be no direct
sunlight. (Same as for saving)
Vibration Resistance
- intermittent vibration
10 ~ 57 Hz: 0.075 mm Half Amplitude
57 ~ 150 Hz: 9.8 m/s2 Acceleration
Sweep Count for X, Y, Z: 10 times (80 min. in each direction)
Vibration Resistance
- Continuous vibration
10 ~ 57 Hz: 0.035 mm Half Amplitude
57 ~ 150 Hz: 4.9 m/s2 Acceleration
Sweep Count for X, Y, Z: 10 times (80 min in each direction)
Shock Resistance
147m/s2 Acceleration,
3 times in each direction X, Y, and Z
Noise Immunity
1000 Vp-p, 1micro second, 30 ~ 100 Hz, tested by noise simulator
Dielectric Withstand Voltage 500 V AC > 1 min, tested between power terminals and ground
Insulation Resistance
5 MΩ > at 500 V DC, tested between power terminals and ground
Ground
Grounding resistance of 100 Ω or less. (class D)
Protection
IP 65F
2.2 Power Supply Specifications
Items
F94*GOT-SWD-E
Power Supply Voltage
24V DC, +10% -15%
Power Supply Ripple
200 mV or less
F94*GOT-LWD-E
b) GOT
Ratings: 390 mA at 24V DC
Cautions:
Fuse built-in GOT (impossible to change)
Max. Allowable Momentary
Power Supply Failure period
5 ms; If less than 5 ms, the GOT will continue operation. If 5 ms or
more, the GOT will shut down.
Battery
Built-in, PM-20BL type lithium battery. (Approximately 5 years
battery life)
c)
2.3 Screen Hardware Specifications
F94*GOT-SWD-E
a) Clamping bolt
F94*GOT-LWD-E
STN colours liquid crystal
Resolution
320 × 240 (dot), 40 characters × 15 lines
Dot Pitch
0.36 mm (0.014") Horizontal × 0.36 mm (0.014") Vertical.
Effective Display Size
115 mm (4.53") × 86 mm (3.39"); 6 (5.7 inch) type
Number of Colours
8 colours
Life of liquid crystal
Approximately 50,000 hours
(Operating temperature: 25 °C / 77°F)
Backlight
Cold cathode tube
Life of Backlight
40,000 hours or more
(Operating temperature: 25 °C / 77°F)
Touch Keys
Maximum 50 touch keys / screen, 20 × 12 matrix
RS-422
RS-232C 1channel
1 7 2 (6 .7 7 ")
5 7 (2 .2 4 ")
b) Packing seal
When the same screen is displayed for a long time, an incidental color or partial discoloration is
generated on the screen due to heat damage, and it may not disappear.
•
Using the GOT Backlight OFF function can prolong the life of the backlight.
For details on the Backlight OFF function, refer to the following.
GOT-F900 Series OPERATION MANUAL/GOT-F900 Series OPERATION MANUAL [GT Designer2
Version]
3. Installation
+
5 ( 0 .2 0 " ) o r le s s
b )
Do not mount the GOT in an environment that contains dust, soot corrosive or conducive
dust, corrosive or flammable gas, or expose the unit to high temperatures, dew
condensation, direct sunlight, rain, wind or impact and vibration.
If the GOT is used in such a place, electrical shock, fire, malfunction, damages or
deterioration may occur.
Never drop cutting chips or electric wire chips into the ventilation window of the GOT
when drilling screw holes or performing wiring. Such chips may cause fire, failure or
malfunction.
Turn off the power before securely connecting any cables. Poor connection may cause
malfunction.
2) Remove the existing battery from the battery holder, and
disconnect.
1 5 3 ( 6 .0 2 " ) + 1 (+ 0 .0 4 ")
0
4) Insert the new battery into the battery holder, and attach the
cover.
Note:
•
Wire the power supply using electric wires of 0.75 mm2 or more so that voltage drop will
not occur. Use M3 size crimp style terminals. Securely tighten crimp-style terminals with a
torque of 0.5 ~ 0.8 N‚m so that errors can be avoided.
•
Insure correct termination of the DC power source, incorrect connection may result in unit
failure or serious damage to the GOT being burnt.
•
Attach a fuse of 2 A to the 24V DC power supply.
•
Perform Class D (100Ω or less) grounding with an electric wire of at least 1.25 mm2.
Never perform common grounding of the GOT and a strong power system.
6.2 Backlight Replacement
Replace the backlight F9GT-40LTS using the following procedure.
Note: Removing Rear Panel
If the rear panel is pulled using an excessive force, the cable connecting the rear panel and
the front panel may be disconnected or the PCB may be damaged. Be careful.
6.2.1 Replacement procedure
a )
Note
•
Use an external power supply to provide 24V DC.
(The service power supply of the programmable controller cannot be used.)
•
Even if instantaneous power interruption of less than 5 ms occurs, the GOT continues to
operate. When power interruption for considerable period of time or voltage drop occurs,
the GOT stops its operation. However, when the power supply is recovered, the GOT
automatically restar ts its operation. (The screen displayed just after recovery is
determined by the working environment originally set.)
Grounding resistance
100Ω or less (class D)
24V DC external
power supply
1 2 1 + 01
( 4 . 7 6 " + 00 . 0 4 " )
Fuse (2A)
24V DC
PLC
1)Make sure that the power of the GOT is turned OFF.
Remove the mounting screws (a) located at 4 corners, and
slowly remove the rear panel.
2)Disconnect the backlight connector (b).
3)Remove the backlight F9GT-40LTS (c) from the backlight
fixing holder (d).
It is recommended to insert a screwdriver into the holder.
Then, the backlight can be taken out easily.
d )
c )
b )
4)Attach a new backlight F9GT-40LTS (c). Put it into the GOT
by performing the steps 1) ~ 3) in the reverse order.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi;
opportunity loss or lost profits caused by faults in the Mitsubishi products; damage, secondary damage,
accident compensation caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For the detailed warranty, refer to the GOT-F900 Series HARDWARE MANUAL [CONNECTION].
GOT
Manual number : JY992D94201
5. Expansion Module
Note
Make sure that the thickness of the panel surface is no more than 5 mm (0.20").
3) Within 30 seconds, connect a new battery.
Cut OFF all external phases of power before installation or wiring to avoid electric shock or
serious damage to the product.
U n it: m m ( in c h e s )
S lo t to b e c u t o n p a n e l
1) Turn off the power to the GOT and remove the battery holder
cover.
Caution:
The GOT is designed to be mounted in a panel. Install it using the following procedure:
1) Preparing the panel surface.
On the panel surface, cut a rectangular mounting slot of the
dimensions shown on the right.
At this time, space of 10 mm is required at each of the top
and the bottom of the slot, inside the panel for metal fixtures
as shown in “4) Dimensions required inside the panel for
installation”.
6.1.1 Replacement Procedure
4. Power Supply Wiring
Note;
•
For approximately one month after the control device for battery voltage drop turns ON, the
battery will back up the alarm history, sampling and the current time. When the control device
(system information) turns ON, replace the battery (PM-20BL) as soon as possible.
The screen data is stored in the flash memory. Even if the battery is totally worn out, the screen
data will remaven after severe battery voltage loss.
PM-20BL
•
•
Never disassemble or modify the GOT. Disassembly or modification may cause failure,
malfunction or fire. For repair, please, contact a service representative.
Note:
a )
Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel. It is
impossible to completely avoid this symptom, as the liquid crystal display comprises of a great
number of display elements.
Flickers may be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not caused by product defect.
•
•
When the battery voltage drops, a control device (system information) set by the screen design software
turns ON. The control device interlocks with an auxiliary relay in the PLC. It is recommended to provide a
lamp while utilizing the output of the PLC so that voltage drop can be monitored outside the GOT.
For details of control devices, refer to the GOT-F900 Series Operation Manual.
2 4 V D C
Flash memory 512 KB (built-in)
Always power OFF and remove the GOT from the panel before starting replacement of
the backlight and battery. If this is not the case, the backlight may be dropped and cause
injury, or electrical shock sustained.
6.1 Battery Replacement
4) Dimensions required inside the panel for
installation.
When installing the GOT, make sure that
the inner dimensions shown on the right
are available.
-
User Memory
•
When repairing liquid crystal screen, please, contact a service representative.
1channel
User screen: 500 screens or less
System screen: Allocated screens No. 1001-1030.
Correctly connect the battery for memory backup. Never charge, disassemble, heat, burn
or short-circuit the battery. If the battery is handled in such a way, or fire may be caused.
Turn OFF the power, before connecting/disconnecting cables.
Connecting/disconnecting cables while the power is turned on will cause failure or
malfunction caused.
Make sure to tighten the clamping bolts with a torque of 0.3 ~ 0.5 N‚m.
a) PLC connection cable
Number of Screens
•
Note:
Note:
White and Black
RS-232C
a )
b )
b) Mounting bracket
Display Device
RS-422
3) Fixing the GOT
Put hooks of the mounting brackets (supplied) in to the
mounting holes of the GOT. Tighten mounting bolts (also
supplied) until the GOT is securely fixed.
Fix mounting bolts in all four positions, above and below the
GOT.
1 4 0 (5 .5 1 ")
Items
•
6. Maintenance
c) Mounting slot
180 mA at 24 V DC when backlight is turned OFF
Fuse
Interface
a)
b) F9GT-40FMB
F9GT-40FMB has a built-in flash memory and can transfer screen data when installed in the GOT.
(When installed in OS versions either than 6.40, screen display is not available while transferring data
from F9GT-40FMB to the GOT.)
For operating procedures and specifications, refer to the manual for F9GT-40FMB.
b)
a) Packing seal
Ratings: 410 mA at 24V DC
Current Consumption
2) Inserting the GOT into the panel surface
Attach the packing seal to the GOT, and insert the GOT
from the front face of the panel surface.
a) F9GT-40UMB
The data transfer adaptor F9GT-40UMB is used to store the user screen data in the EPROM for user
screen data FX-EPROM-4M to the flush memory in the GOT. (The user screen data can be written to
the EPROM using the screen design software.)
This adaptor is useful when the same screen data is transferred to two or more GOT units.
For the operating procedure of F9GT-40UMB, please see the manual of F9GT-40UMB.
Manual revision : E
Date
: Sep. 2008
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN