4CH / 8CH H.264
Digital Video Recorder
USER MANUAL
2013 FEB V1.0
TYPE2 optional
WARNING







Do not expose the DVR under the sunlight, heat or
wet environment while installation. As it could
decrease the performance of DVR and damage the
machine.
Do not touch the power plug or case with wet hands
as this could result electric shock.
Do not forcedly bend or put heavy object on power
cable as this could result in injury to personal or
equipment.
Do not operate with damaged power cord or loose
electrical outlet as this could result in electric shock or
accident.
Please use individual power instead of share electrical
outlets with other electrical equipment as this could
result in damage or accident.
Do not attempt to service this DVR by yourself as it
may expose you to dangerous voltage or other
hazards. Please refer all service to the qualified
servicing distributor.
Do not open the covers or insert any object into DVR.
CAUTION


Do not place the machine on an uneven surface or it would
decrease the DVR efficiency or malfunction.
Avoid any shock or bumping of the DVR while recording.
Improper handling could damage the system.
CAUTION
Make sure the voltage selector switch is set
to appropriate setting before plug in!
ii
CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
Specification ............................................................................................. 1
Front Panel ............................................................................................... 2
Installation ................................................................................................ 3
DVR Installation ........................................................................................ 3
System Operation ..................................................................................... 4
Display Setup ........................................................................................... 6
Search ...................................................................................................... 7
Main Menu ................................................................................................ 9
8.1 Camera Setup .................................................................................. 9
8.2 Record Setup ................................................................................. 10
8.3 Motion Detection ............................................................................ 13
8.4 Network Setup (TYPE 2) ................................................................ 14
8.5 Log Search ..................................................................................... 16
8.6 Backup ........................................................................................... 17
8.7 System ........................................................................................... 18
8.7.1 Time Setting ......................................................................... 18
8.7.2 HDD Setup ........................................................................... 19
8.7.3 Display Setting ..................................................................... 20
8.7.4 System Information .............................................................. 21
8.7.5 User Password ..................................................................... 21
8.7.6 System Language ................................................................ 22
8.7.7 Audio Setting ........................................................................ 22
8.7.8 System Maintenance ............................................................ 23
9. H264 Player Operation ........................................................................... 24
10. Cell Phone Monitoring Operation (TYPE 2) ............................................ 27
11. Web Operation (TYPE 2) ........................................................................ 48
12. Default Setting ........................................................................................ 56
iii
1. Specification
Video Format
NTSC
PAL
Video Input
4 CH Input / BNC
Audio Input
2 CH Input / RCA
Video Output
1CH Output / BNC
Audio Output
1CH Output / RCA
XGA Output
800x600, 1024x768, 1280x1024, 1440x900
Display Mode
Full Screen, 4CH Split Screen, Auto Switch, Picture in Picture
Display Resolution
720 x 480
720 x 576
Highest
720 x 480
720 x 576
High
720 x 240
720 x 288
Normal
360 x 240
360 x 288
Max. 120 FPS
Max. 100 FPS
Recording
Resolution
Recording Frame
Compression Algorithm
H.264
Operating System
Embedded Linux
Pentaplex
Live / Record / Playback
Recording Mode
Manual, Schedule, Event
Schedule Recording
Full Recording, Motion, Manual Recording
Status Indicator
Power Indicator, HDD Indicator
Motion Trigger, Video Loss
Event Mode
Recording Duration: 10~60 sec.
Normal Speed: x1
Fast Forward: x2 / x4 / x8 / x16 /x32multiple speed
Playback Mode
Slow Forward: 1/2, 1/4, 1/8 multiple speed
Fast Rewind: x2 / x4 / x8 / x16 /x32
Frame by Frame Playback: Forward
Search Function: Time / Event
HDD Type
SATA 3.5”HDD x 1 (No HDD Included)
Recommend use 1TB capacity for HDD or below
HDD Management
Automatic Format System
Backup Device
USB 2.0 Flash Memory Stick
Firmware Update
Host USB
Multi-Language
Control Mode
Network (TYPE 2)
English / Chinese / Others
Front Panel / Remote Control / USB Mouse
Network Protocol
TCP/IP / PPPoE / DHCP / SMTP / DDNS
Network Control
IE Browser
Network Function
Live Display / Playback / System Setup
Power Supply
DC 12V / 2A (AC100V~240V 50/60HZ)
Unit Dimension
224mm (W)x 208mm (D) x 52 (H) mm
Unit Weight 1.5kg
Weight
Operating Temperature
0℃ ~ 46℃
1
2. Front Panel
Power Indicator
HDD Indicator
The LED lights on when power on.
The LED lights on when the HDD is written.
Up
To move up of the selection setting in the menu.
Channel 1
Under the live viewing mode, channel 1 display.
Channel select
Left
Channel 2
Fast Rewind
Down
Channel 3
Slow Forward
Right
Channel 4
Fast Forward
Enter
MENU
Quad
Pause
Step
Manual Record
STOP
Play
Single channel (1~4ch) and quad display in playback mode.
To move left of the selection setting in menu.
Under the live viewing mode, channel 2 display.
Rewind speed: x2 / x4 / x8 /x16 /x32.
To move down of the selection setting in the menu.
Under the live viewing mode, channel 3 display.
Slow Forward speed: 1/2, 1/4, 1/8.
To move right of the selection setting in menu.
Under the live viewing mode, channel 4 display.
Forward speed: x2 / x4 / x8 / x16 /x32.
Press the Enter button to confirm the setup or go into sub-menu.
Under the live viewing mode, press MENU to enter the main menu.
Under the menu mode, press MENU to go to the upper menu.
Under the live viewing mode, quad screen display.
Under the playback mode, press the button to pause the playback.
Under the playback mode, press Step button to enter Play Frame by
Frame mode.
Press this button to start recording in live mode.
Under the playback mode, press the button to stop the operation or
go to upper menu.
Under the live viewing mode, press the Play button to enter the
playback mode.
2
3. Installation
TYPE 2: Network
1
VGA
PC Monitor Output
2
Video In
3
Video Out
1CH Video Output (BNC)
4
Audio Out
1CH Audio Output (RCA)
5
Audio In
6
USB 2.0 Port
7
DC12V
8
LAN
4CH Video Input (BNC)
2CH Audio Input
USB Mouse / USB backup or firmware update.
Power Input
RJ-45 Network Connection (for TYPE 2)
4. DVR Installation


Connect the camera video output to the DVR video input port with BNC
connectors.
The camera install coaxial cable is suggested cat 6 or above.
Power Installation
Please use the provided power cable and adaptor to connect the DVR
(AC100V~AC240V). Please refer to Installation for connecting position. The
DVR system will enter into live viewing mode when power is connected.
3

Please refer to Display Setup - Live Viewing Mode for more information.
DVR Network installation (for TYPE 2)
Please connect DVR to HUB or router by using RJ-45 network cable and
make sure the DVR network indicator LED is on.
(Please refer to Network Setup for further network setting information of
using static IP, PPPoE or DHCP.
5. System Operation
There are 3 kinds of DVR control method: front panel, remote control and USB
mouse.
 USB Mouse Operation
1. Quick Menu: Right click the mouse button under the live viewing mode to
go for enter into Quick Menu.
2. Left click the mouse button under the main menu to go to the sub-select
menu.
3. Left click the mouse button under the select menu to go to the sub-menu.
Use the mouse to change the setting.
 Remote Control Operation
Remote Control and front panel operation are the same; please refer to Front
Panel and the reference table of the button as below.
CH2 display
CH1 display
Record
CH3 display
CH4 display
Mute
Quad display
Menu
Navigator
Enter
Fast Rewind
Fast Forward
Play
Stop/ Remote ID Setup
Step/Pause
 On live mode, click “Fast Forward” to switch on the GUI display.

Virtual Keyboard Operation
The text input of the virtual keyboard is as below:
4
Front Panel & Remote
Menu Operation
Mouse Operation
Control Operation
Select character from virtual keyboard
[Up/Down/Left/Right]
[Move Cursor]
Keyin the select character
[Enter]
[Left Click]
Exit the virtual keyboard
[MENU]
[Left Click]out of selection area
Key Description of Virtual Keyboard
Delete the previous character
Switch to text input
Enter key. Save and exit the virtual keyboard
Other Keys

Character Keyin
Main Menu Operation
Main menu

Setup Operation
Front Panel & Remote Control
USB Mouse
Select
[Up/Down/Left/Right]
[Moving Cursor]
Enter Select Menu
[Enter]
[Left Click]
Setup Operation
Setup
Setup Operation
Front Panel & Remote Control
USB Mouse
Select
[Up/Down/Left/Right]
[Moving Cursor]
Confirm Select Setting
[Enter]
[Left Click]
Change the Select Setting
[Left/Right]
[Left Click]
5
6. Display Setup
There are 2 kinds of screen display mode: Live, Auto Switching .
 Live Viewing Mode
The DVR will go to the live viewing mode after boot up. There are 5 different
status icon:
●: Record
M: Motion Triggered
L: Video Loss
: Sound on/off Setup Operation
Front Panel&Remote Control
Channel 1~4 Single Channel
Display
[CH1~4]
4 Channel Split Display
[4 CH Split]
Quick Menu
[MENU]
[Right]
Playback Mode
[Play]
[Right] QuickMenu
Start/Stop the Manual Record
[Record]
[Right] QuickMenu
Start/Stop the Auto Switching
-
[Right] QuickMenu
Start/Stop Mute
Remote Control
[Mute]

USB Mouse
Select one of channel
[Double click left button]
Under single channel
[Double click left button]
[Left] Left Click
Quick Menu
Main Menu
Remote Lock
PIP
Search
Info
Back Up
Auto Switching
Manual REC
Setup Operation
Front Panel & Remote Control
USB Mouse
Select Item
[Left/Right]
[Moving Cursor]
Enter the Select Item
[Up/Down]
[Moving Cursor]
Confirm the Select Item
[Enter]
[Left Click]
Exit
[MENU]
[Left Click] out of selection area
6

Playback Operation
Setup Operation
Front Panel & Remote
Control
Fast Rewind
[Fast Rewind]
Fast Forward
[Fast Forward]
Step Forward
[StepForward]
Step/Pause
[Step/Pause]
Play 1x
[Play]
Stop
[Stop]
Digital Zoon
None
Drag by Left Click
Derived Image
None
[Left click]
1~4 Single Channel Display
[1~4 Channel]
Select Channel [Double left click]
4 split Display
[4 split]
Under single channel
[Double left click]

USB Mouse
Auto Switching
1. Auto switch starts from order CH1~CH4, 4 split channel.
2. Press the button again to stop the function.
7. Search
In Live mode, use Play button in the front panel/remote controller or right clicking
the mouse to switch to the Search function.
7
Setup Operation



Front Panel & Remote
USB Mouse
Controller
Search
[Enter]
[Left Click]
Select Channel
[Up/Down]
[Moving Cursor]
Select Dates
[Up/Down/Left/Right]
[Moving Cursor]
Playback
[Enter]
[Left Click]
Return to Upper Menu
[MENU]
[Right click] or [Left click
]
No data: no color, data of alarm trigger: red color, normal record data: green
color.
Select the first half of hour frame under the date, the playback will start from
00 mins: 00 sec. Select the second half of hour frame under the date, the
playback will start from 30mins:00sec. If there is no data on the date, please
try to search from record list.
Select any of 4 channels to playback.

Record List
Enter Select Item
Front & Remote
Controller
[Enter]
Select Item
[Up/Down/Left/Right]
Return to Upper Menu
[MENU]
Setup Operation
USB Mouse
[Left Click]
[Moving Cursor]
[Right click] or [Left click
]
First Page
Previous Page
Next Page
8
Last Page
Mark all the events in this page
BackUp

List all of recording data and click on one of record data to
playback.

Backup
Please click “BACKUP” to backup the selecting file to USB memory
stick.
8. Main Menu
Camera
Record
Motion
Network
Log Search
Back Up
System
※ Network for TYPE 2
8.1



Setup Operation
Front Panel & Remote
Controller
USB Mouse
Select Item
[Up/Down/Left/Right]
[Moving Cursor]
Enter Select Item
[Enter]
[Left Click]
Exit Main Menu
[MENU]
[Right click] or [Left click
]
Camera Setup
Channel
Select one channel to set. Use CopyButton to copy present settings to other
channels.
Camera Title
Set the title of camera. Key in by using virtual keyboard.
Title Position
Set the title position. Set: Top Left, Top Right, Bottom Left, Bottom Right and
Off.
9


Display
Display the channel, set: On/Off
Camera Color Setup






8.2
Hue: 0~50
Brightness: 0~50
Contrast: 0~50
Saturation: 0~50
Buzzer Duration
The buzzer ON duration when video loss.
Time Display
Display the time in LIVE mode. Values: ON/OFF.
Record Setup

Record Enable Setup
On/Off the channel.
Watermark: Insert the words of watermark.

Resolution Setup
NTSC Recording Resolution: 720x480 / 720x240 / 360x240.
PAL Recording Resolution: 720x576 / 720x288 / 360x288.
10

Frame Rate Setup
Setting of Frame Rate: NTSC: 0-30 frames/sec; PAL: 0-25 frames/sec.

Quality Setup
Setting of recording quality: Values 1-5. The bigger value, the better quality.

Pre Record setting
Pre Recording time when motion alarm. Values: 0-10 seconds.
11



Audio
On/Off the sound effects.
Encode Mode
Encoding of channel. Values: VBR or CBR.
Record schedule setup
Always and Schedule Record.
 Record Schedule
Schedule
Setup Operation
Front Panel & Remote Controller
USB Mouse
Enter Select Item
[Enter]
[Left Click]
Select Channel
[Up/Down]
[Moving mouse wheel]
Select Time&Date
[Up/Down/Left/Right]
[Click/Drag-draw]
Return to Upper Menu
[MENU]
[Right Click] or [Left Click
]
 Copy
(1) Select source (2) Select target (3) Press COPY icon to copy.
12
8.3




Motion Detection
Channel
Select the channel to set. COPY icon can copy the present setting to other
channels.
Enable
Enable/disable motion detection for each camera. Set: On/Off
Sensitivity
Sensitivity level of motion detection. Set: 1~10. Higher value equal more
sensitive.
Motion Area Setup
Setup by each small square.
Setup Operation
Front Panel & Remote Controller
USB Mouse
Area Selection
[Up/Down/Left/Right]
[Moving Cursor]
(1)Move to the area
(2)Press Enter to set the area
[Drag by Left Click]
(1)Move to the area
(2)Press Enter to set the area
[Drag by Left Click]
[MENU]
[Right Click]
Set Detection Area: must set
on none detection
area(Transparent Area)
Clear Detection Area: clear the
set detection area: must set on
detection area(Green Area)
Return to Upper Menu



Record Duration
The duration of the recording after triggered: 10, 20… 60 sec. or off.
Buzzer Duration
The duration of the buzzer beeping after being triggered: 1, 5, 10, 15, 20, 30
sec.
Event Popup
The Duration of single channel display after being triggered: 1, 5, 10, 15, 20
sec or off.
13
8.4










Network Setup (TYPE 2)
Mode
Set the connection method. Set: Static IP, DHCP, PPPoE.
Media Port
Port used for stream media. Default is port 9000.
WEB Port
Port used for web access. Default is port 80.
Command Port
Port used for settings. Default is port 8000.
Mobile Port
Mobile phone port (factory default): 15961.
IP Address
Assigned IP address.
Netmask
Assigned net mask
Gateway
Assigned gateway
HOST Name
Set the HOST Name of DVR.
PPPOE
Need account and password for PPPoE.
14

DDNS setting
HOST NAME
DVR NAME
DNS1 First Domain Name Server, Default : 168.95.1.1
DNS2 Second Domain Name Server, Default :168.95.192.1
DDNS
Enable/disable Dynamic Domain Name server. Values: On, Off.
 DDNS Server
DDNS Server, Values: 3322, dyndns, cctvdvr.
When using DDNS server, HOST name, server name and
account/password are required.
E-Mail Setting












E-MAIL
Forward E-mail after alarm triggered. Enable: On/Off
SSL
Enable the SSL encryption. Recommend to set on if it is using
gmail.
Port
SMTP port number key in. For example, gmail port 465.
Server
SMTP server key in. For example, gmail: smtp.gmail.com
Password
Sender E-mail account password
From
Sender E-mail address key in. For example,
gmail: mail1@gmail.com
To
Receiver E-mail address key in. For example,
gmail: mail2@gmail.com
Interval
When alarm keeps going, the time span to send E-mail. Values: 10,
15
30, 60 seconds.
8.5


Log Search
Log type
Set conditions for searching: type and time range. Log type can be ALL,
Operation, Motion Detection, and Video Loss.
Start/End time
Set the search range (Year/Month/Day). Press [SEARCH] to search.
Setup Operation
Front & Remote Controller
USB Mouse
Enter Select Item
[Enter]
[Left Click]
Select Item
[Up/Down/Left/Right]
[Moving Cursor]
Return to Upper Menu
[MENU]
[Right click] or [Left click
]
First Page
Previous Page
Next Page
Last Page
Backup to USB disk
★ When Trigger Recording is marked, click to playback.
16
8.6



Backup
Channel
Backup all channels or single channel 1-4.
Record Type
Select all, normal or alarm.
Start/End time
Select the backup range of time. Press Search to start searching. The record
list will be shown if available and follow [Record list] to backup.
Storage Device Choose
17
8.7
System
Time Setup
HDD
Display
System Information
Password
Language
Audio
System Maintenance
8.7.1
Time Setting
TYPE 1: no Network





TYPE 2: Network
Date/Time
Select by using virtual keyboard.
Date Format Setup
Set: YY/MM/DD, MM/DD/YY.
Time Format Setup
Set: 24Hours, 12Hours.
Time Zone Setup
Time Zone setting of DVR.
NTP Setting(Network Time Protocol)
NTP: On or Off
Schedule Time: Using virtual keyboard
NTP server: Using virtual keyboard
18
8.7.2

HDD Setup
Format
Format the selected HDD
Format HDD




Overwrite
Enable/Disable Overwrite, Values: On/Off.
If Overwrite is enabled, the period can be set as 6, 12, 24, 36, 48,
72 hours and 7, 15, 30, 60 days.
Pack Time
Set the required packing time frame to allow the system to pack
each saving file under continue recording mode. Pack time setting:
5 min, 10min, 15min, 20min, 30min, and 60min.
HDD Error Buzzer Enable
When the hard drive does not have enough space or something
wrong, set the buzzer on. Values: On/Off.
USB Disk Info
19
Format USB Memory Stick
8.7.3





Display Setting
GUI Display
GUI display mode can be VIDEO or VGA.
Video Switching Time
Set the switching time when switching channels in video mode.
Values: 1-99 seconds. (0 sec is Off)
VGA Switching Time
Set the switching time when switching channels in VGA mode.
Values: 1-99 seconds. (0 sec is Off)
Switching Sequence
Set the switching sequence of channels.
Video Margin
Set the display margins of the screen. They are Left, Right, Top and
Bottom with range between 0 - 36.
20

XGA Resolution
XGA Resolution: 800x600, 1024x768, 1280x1024, 1440x900.
8.7.4 System Information
Provide the firmware version, MAC address, HDD status….
8.7.5
User Password
TYPE 1: no Network




TYPE 2: Network
Password Setup
Enable/Disable password checking. Values: On/Off (Default)
Administrator account/password can not be blank. And at least 4
characters for the password.
Administrator account/password
Administrator account allows user to access all of functions.
User account/password
Access rights can be assigned by setting.
Remote ID setup
Can adjust remote control ID to control multiple DVR.
21
8.7.6


8.7.7

System Language
Language
Values: Traditional Chinese and English. Auto rebooting after
change.
Function Tip
Show function tips below the menu items.
Value: On/Off (Default).
Audio Setting
Audio Volume
Set the volume of audio In/Out. Values: 1-10. (Default: 5)
22
8.7.8


System Maintenance
Auto maintenance: Set time for auto rebooting. Value: On/Off.
Auto rebooting setting
F/W update
Please plug the USB memory stick into the USB port on the DVR
rear panel after download the new firmware to the USB memory
stick.
Note: the firmware only can be upgraded by using the USB port. Please don’t
operate the system, remove the USB memory stick or remove the power while it
is in upgrade progressing in order to prevent any serious system error. The
system will automatic reboot after upgrade.

Load Setup Default
Load factory default. Refer to [Default Setting].
TYPE 1: no Network
TYPE 2: Network
Backup: For copying the saved setting from one specific DVR to
other DVR use.
Restore: For restoring the saved setting in one specific DVR from
other DVR use.
Remark: For backup or restore, please plug the USB flash memory drive into the
USB socket of DVR. Please also do not change the saved setting file name to
avoid the serious system error. After Finishing backup and restore, please restart
DVR. 

Reboot the DVR
Reboot the DVR.
ShutDown
System will close the recording file. Please remove the power line
manually.
23
9.
H264 Player Operation



Preface
H264 Player software allows to playback the backup saving file from the
DVR.
System Requirement
Operating System: Windows 2000, XP, Vista, Windows 7.
Program obtainment and installation
While user start to backup the file from DVR, the system will automatically
copy the H264Player.exe file and recorded data to the backup device for
example, an USB flash memory stick.
 Execute the installation file
Step 1: Ask for the Installation
Step 2: Select the Install Location
24
Step 3: Select Additional Tasks
Step4: Install Confirmation
Step 5: Installation Complete
25

User Interface
Open File
Click
Pause
Click
Stop
Click
Play 1x
Click
Fast Forward
Click
Slow Forward
Click
Capture the image (snap
shot) to the host computer
Click
Volume Control
Drag
Rewind
Click
Step Forward
Click
Mark start time
Click
Mark end time
Click
Backup
Click
Right click the mouse to open the
Pop-up Menu
pop-up menu including Setting,
Language, About H264Player, Exit
26
10. Cell Phone Monitoring Operation (TYPE 2)
 JAVA Script surveillance:
1. The mobile Phone must support JAVA Script.
2. To download the JAVA software: open Internet Browser on the mobile phone,
and enter the IP address of the DVR and add /viewer.jar at the end. Example:
http://xx.xxx.xxx/viewer.jar.
3. Execute the application.
4. Click on “Add” on the drop down
menu to add an IP address.
5. Enter the IP address, user name
and the password of the DVR and
click on “Save”.
6. Enter the correct IP address and
click on “Open”.
7. Click on “Connect” to connect to the 8. Connecting.
DVR.
9. Connected.
Menu
10. If fail to connect, please repeat
steps 7 to 9.
Capture
Channel[1~4]
27
■ Android Software install/setup procedure
Before the installation, please check the ”Allow Non-market application” or “unknown
source” checkbox in your mobile phone< PIC 1~2>.
<PIC 1>
< PIC 2>
First method
1. First, please make sure the PC synchronize software had installed and activated in
your Android mobile phone. And connect your android phone to PC via USB.
2. Install “Castillo player” software player to the Android phone through your
synchronize software. You may see the example below in the case of HTC.
<PIC 3>
28
<PIC 4>
Method two
You may copy the APK installation package to your mobile phone or memory card,
and then install it through other software.
1. Copy the “Castillo player” software package to your mobile phone through USB or
directly to SD memory card.
2. Download the free APK installation software from Market, for example
APKinstallerc or AppInstaller, here we use AppInstaller for example<PIC 5~6>.
<PIC 5>
<PIC 6>
29
3. Run the AppInstaller program, install the APK software package from your SD
memory card<PIC 7~8>.
<PIC 7>
<PIC 8>
4. After the installation, you may find the “Castillo Player” in your program list, click it
to run the program<PIC 9>.
<PIC 9>
30
5. Press the “Setup” button to setup the connection setting <PIC 10>. Enter your
individual configuration<PIC 11>.
<PIC 10>
<PIC 11>
6. After setting complete, enter a name you prefer then click the “Add to my favorite”
checkbox to save the setting<PIC 12~13>.
<PIC 12>
<PIC 13>
31
7. Press “Connect” button<PIC 14>, it’ll connect to the DVR according to your setup,
and you may see the DVR picture after the connection established<PIC 15>.
<PIC 14>
<PIC 15>
8. <PIC 16>Operate instruction below:
Connect/Disconnect
Set up
Channel
Display screen
PTZ Zoom/aperture/focal
Snap shot
PTZ direction control
Full screen <PIC 16>
32
■ iPhone software install/setup procedure
1. Download the “Castillo player” in AppStore then install it to your IPhone.
<PIC 1~6>
<PIC 1>
<PIC 2>
<PIC 3>
<PIC 4>
<PIC 5>
<PIC 6>
33
2. Run the “Castillo Player” after installation<PIC 7>. Press “setup” button to setup
the connection setting<PIC 8>. Enter your individual configuration then press
“back” button to go back to the main screen<PIC 9>.
<PIC 7>
<PIC 8>
<PIC 9>
3. Press “Play” button, then you may see the DVR live view picture after the
connection established <PIC 10~11>.
<PIC 10>
<PIC 11>
34
4. <PIC 12> Operate instruction below:
Display screen
Zoom/aperture/focal distance PTZ direction control
Channel Connect/Disconnect
Set up
Snap shot
Next page Full screen <PIC 12> 35
■ Symbian Software install/setup procedure
1. Copy the Symbian player to your mobile phone or memory card; you may see the
example below in the case of NOKIA. <PIC 1~5>
<PIC 1>
<PIC 2>
<PIC 3>
<PIC 4>
<PIC 5>
2. Connect the mobile phone to PC via USB, copy the live view software to the
memory card of your mobile phone <PIC 6>.
36
<PIC 6> 3. Before the installation, please make sure you had cancel the “Only Signed
Application”, also cancel the “Connection credentials check” <PIC 7~11>.
<PIC 7>
<PIC 8>
<PIC 9>
37
<PIC 10>
<PIC 11> 4. Enter the folder which you’d saved the live view software “fuho_20110221.sisx”,
double click to install, follow the instruction to proceed <PIC 12~22>. <PIC 12>
<PIC 13>
<PIC 15>
<PIC 14> <PIC 16>
<PIC 17> 38
<PIC 18>
<PIC 19>
<PIC 20> <PIC 21>
<PIC 22> 5. After the installation, enter the “Installed Application” and you may see the “Castillo
Player” inside <PIC 23~25>. <PIC 23>
<PIC 24>
<PIC 25> 39
6. Click and run the Castillo Player program <PIC 26~27>. <PIC 26>
<PIC 27>
7. Press the “Setup” button to setup the connection setting. After setting complete,
click the “Add to my favorite” button to save the setting. Press “Connect” button, it’ll
connect to the DVR according to your setup <PIC 28~32>.
<PIC 28>
<PIC 29>
<PIC 30> 40
<PIC 31>
<PIC 32>
8. <PIC 33>Operate instruction below:
Display Screen
PTZ direction control Zoom/ Aperture/
Focal distance
Channel
Connect / Disconnect
Exit
Full screen
Snapshot
Add to
Set up
Next page
<PIC 33>
41
■ Windows Mobile Software install/setup procedure
1. Please install “Microsoft ActiveSync” into the PC before installing CAB software.
2. Execute the Microsoft ActiveSync program in your PC first, and connect the
Windows Mobile SmartPhone to PC via USB, then it’ll synchronize the
SmartPhone and PC.
3. In ActiveSync program, Click “Browse” button to open the mobile device
folder <PIC 1>.
<PIC 1>
4. Copy the .CAB file of Castillo Player to your mobile device folder, or any
other folder according to your individual needs <PIC 2>.
<PIC 2>
42
5. Please disconnect the SmartPhone from your PC, and begin the
installation below:
6. Execute the Castillo Player CAB install package from the File browser, you
may find it in your mobile device folder <PIC 3~5>.
<PIC 3>
<PIC 4>
<PIC 5>
7. Double click and it’ll begin the installation, follow the instruction for
setting up. After the installation, you may find the “Castillo Player” in
your program <PIC 6~10>.
<PIC 6>
<PIC 7>
<PIC 8>
43
<PIC 9>
<PIC 10>
8. Run the Castillo Player program, press the “Setup” button to setup the connection
setting. After setting complete, enter a name you prefer then click the “Add to my
favorite” checkbox to save the setting. Press OK and Leave to go back to the main
screen <PIC 11~14>.
<PIC 11>
<PIC 12>
<PIC 13>
44
<PIC 14>
9. Press “Connect” button, it’ll connect to the DVR according to your setup, and you
may see the DVR picture after the connection established <PIC 15~16>.
<PIC 15>
<PIC 16>
45
10. <PIC 17>Operate instruction below:
Channel
Connect/Disconnect
Display screen
PTZ direction Control
snapshot
Zoom/aperture/focal distance
<PIC 17>
46

1.
Blackberry Software Connect Procedure
Blackberry RTSP Connect procedure:
Verify Authentication, website address input format as below
rtsp://(website address)/ch(channel number)?user=(user ID)&pwd=(user
password)
e.g. rtsp://f16.cctvdvr.com.tw:554/ch2?user=2222&pwd=2222
2.
Mobile Webpage:
Please enter the ID & password again after you login, or you’ll get black screen of
permission denied as below:
47

Operation System For Mobile Phone Application
O/S
Version
Android
2.1、2.2、2.3
iPhone
3.x、4.x
Castillo player
WinMobile
6.5.x
CastilloPlayer_5.0.3.CAB
Symbian
S60 v3 above
CastilloPlayer_5.1.713.sisx
BlackBerry
Mobile Phone Software
CastilloPlayer(Android_1.5~2.1).apk
CastilloPlayer(Android_2.2~2.3).apk
Support RTSP
None
Protocol
11. Web Operation (TYPE 2)



Preface
The Web Application Manager allows the user to remotely monitoring,
playback, backup through the DVR.
System Requirement
Operating System: Windows 2000, XP, Vista, Windows 7
Web Browser: Internet Explorer
Add-on Installation
Please use the IE browser to login the IP address of DVR setting. If the user
is the first time to login the page, the system will ask the user to download
and install the add-on as you can see the page below. Please click the
request to install the ActiveX add-on.
48

User Interface
 Login Page
Please login user name and
password from the setting of DVR
end. 
Live mode
Start/Stop the Live Monitoring
Click
Record the Footage to
Click
Computer
path: Setup/Information)
Snapshot the Image
Enable/Disable Audio
Click
Start recording or
Stop recording (saving
to snap shot the image (saving path:
Setup/Information)
Click
under the live viewing mode to enable the audio,
and click
to disable
Volume Control
Click
Switch Channel Display
Double click the channel to enter single channel display,
double click again to return.
Single/4 Display
Click
49

Playback
(1) Select Date
Event Search
or
(2)Click
(3)Click
Playback
Click on pop up file list
Fast Forward
Click “Fast Forward” (Speed: 2X, 4X, 8X, 16X)
Rewind
Click “ Rewind” (Speed: 1/2, 1/ 4X, 1/ 8X, 1/ 16X)
Step Forward
Click “Previous”or “Step”
Snapshot
Click
Mark start time
Click
Mark end time
Click
Backup
Click
Backup
to capture.
Click “Backup”, backup path: Setup System Setting
Backup Location
50

DVR Setting
Cameras
Please refer “Camera Setup” for more information
Record
Please refer “Record Setup” for more information.
MotionDetection
Please refer “Motion Detection” for more information.
51
Network setting
E-MAIL
Log search
52

System Setting
Date/Time Setting
HDD Management
Display
53
System Information
Account / password
Audio Setting
54
System Maintenance

Host setting
55
12. Default Setting
Item
Default Setting
Channel
On
Resolution
Normal
Record
Frame Rate
Real-time
Setup
Quality
Highest
Audio
Disable
Schedule
Always
Channel 1
CH1
Setup
Pack Time
60 Mins
Date Format
YY/MM/DD
Time Format
24 Hours
Time Zone
GMT+08:00
Daylight Saving
Off
XGA Resolution
800 X 600
Output Volume
5
Input Volume
5
CH3
Channel 4
CH4
Title Position
Top Left
Mode
Static IP
Display
On
Media Port
09000
Display Time
On
Web Port
00080
Setup
System
Maintenance
Maintenance
Schedule Setup
1 sec.
Network
IP Address
Setup
NetMask
Hue
25
Brightness
25
Gateway
Contrast
25
DNS
Saturation
25
Channel
Motion
XGA/Audio
Yes
Channel 3
Time
Color
Time Setup
Overwrite
CH2
Switching
Camera
HDD Setup
Default Setting
Channel 2
Camera
Setup
Item
Status
(TYPE 2)
DDNS Setup
(TYPE 2)
192.168.000.10
0
255.255.255.0
192.168.000.00
1
168.095.001.00
1
DDNS
Off
E-MAIL
Off
E-MAIL
Off
Setup
(TYPE 2)
Detection
Sensitivity
Off
5
56
57