Multiple Display Control Protocol for PPM42M5S

SEC-VD-DSW Multiple Display Control - 0008
Multiple Display Control Protocol
for PPM42M5S
PPM42M5H
PPM50M5H
PPM63M5H Series
Copyright © 2004 2005 Samsung Electronics Co., Ltd
SEC-VD-DSW External Control - 0008
1.2. Connection Standards
1) Connection Standards
- Conducts bi-directional communication using RS232.
- Users three signal wires, of TxD (No.2), RxD (No.3), and GND (No.5), among the
RS232 standard wires. (See Fig.1)
- The distance between devices limited to 4m.
- Of the 9 pins of the RS232 port, Nos. 2,3 and 5 are used.
- ID can ge expressed as hexadecimal of given ID, but ID O should be presented only
as 0xFF.
- All
communications are cindeucted in the form of hexadecimal numbers, and the
checksum is the sum of all values except for the header. If, as shown in the example
below (11 + FF + 01 +01 =112), the sum is a three-digit interger, discard rhe first
digit and keep the lower two.
ex) Power On & ID=0
Header
Command
0xAA
0x11
→
ID
Header
Command
0xAA
0x11
Data Length
Data 1
1
Power
0xFF
Check
Sum
Data Length
Data 1
1
1
12
- If you wish to control all units connected with serial cable regardless of the IDs, set
the ID to "0xFE" and send commands.
Here, each wet functions according to the commands received but does not respond with
ACK.
Table 2-1 RS232 Communication Standards
Bits Rate
9600 bps
Data Bits
8 bits
Parity
None
Stop Bits
1 bit
Flow Control
None
Display S/W, VD Business Team, Samsung Electronics
3
SEC-VD-DSW External Control - 0008
Fig 2-1 RS-232 pin out DB-9 pin used for Asynchronous Data
Display S/W, VD Business Team, Samsung Electronics
4
SEC-VD-DSW External Control - 0008
2. Command
No
명령어 종류
Command
Value 값 범위
1
Status Control
0x00
-
2
Time Control
0x01
-
3
On Time Control
0x02
-
4
Off Time Control
0x03
-
5
Video Control
0x04
-
6
RGB Control
0x06
-
7
PIP Status Control
0x07
-
8
Maintenance Control
0x08
-
9
On, Off Timer Status Control
0x0A
-
10
Model Number Control
0x10
-
11
Power Control
0x11
0 ~ 1
12
Volume Control
0x12
0 ~ 100
13
Mute Control
0x13
0 ~ 1
14
Input Source Control
0x14
-
15
Image Size Control
0x15
-
16
Contrast Control
0x24
0 ~ 100
17
Brightness Control
0x25
0 ~ 100
18
Sharpness Control
0x26
0 ~ 100
19
Color Control
0x27
0 ~ 100
20
Tint Control
0x28
0 ~ 100
21
Red Gain Control
0x29
0 ~ 100
22
Green Gain Control
0x2A
0 ~ 100
23
Blue Gain Control
0x2B
0 ~ 100
24
Coarse Control
0x2F
0 ~ 1
25
Fine Control
0x30
0 ~ 1
26
H-Position Control
0x31
0 ~ 1
27
V-Position Control
0x32
0 ~ 1
28
Clear Menu Control
0x34
0
29
IR Lock Control
0x36
0 ~ 1
30
RGB Contrast Control
0x37
0 ~ 100
Display S/W, VD Business Team, Samsung Electronics
5
SEC-VD-DSW External Control - 0008
31
RGB Brightness Control
0x38
0 ~ 100
32
Zoom Control
0x39
0 ~ 1
33
H-Panning Control
0x3A
0 ~ 1
34
V-Panning Control
0x3B
0 ~ 1
35
PIP On/Off Control
0x3C
0 ~ 1
36
Auto Adjustment Control
0x3D
0
37
Color Tone Control
0x3E
0 ~ 4
38
PIP Source Control
0x40
-
39
Main-PIP Swap Control
0x41
0 ~ 1
40
PIP Size Control
0x42
-
41
PIP Locate Control
0x43
0 ~ 4
42
Sound Select Control
0x47
0 ~ 1
43
Pixel Shift Control
0x4C
-
44
Signal Pattern Control
0x4D
0 ~ 1
45
All White Control
0x4E
0 ~ 1
46
Video Wall Control
0x4F
-
47
SBP Timer Control
0x5B
-
48
Video Wall Mode Control
0x5C
0 ~ 1
Note : "-" indicates when the values to be set are multiple.
See "2.1. Detailed Description of Commands" for details.
Display S/W, VD Business Team, Samsung Electronics
6
SEC-VD-DSW External Control - 0008
2.1. Detailed Description of Commands
1) Status Control
●
Function
The Computer shows the current settings for the TV/Minitor.
●
●
Get Status
Header
Command
0xAA
0x00
Header
Command
0xAA
0xFF
Val 3
Val 4
Val 5
Mute
Input
Aspect
ID
Data Length
0
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
9
'A'
0x00
Power
Volume
Val 6
Val 7
Check
Sum
Check
Sum
Ack
ID
N Time NF F Time NF
Power : The Power Code for the TV/Monitor.
Volume : The Volume Value for the TV/Monitor. ( 0 ~ 100 )
Mute : The Mute Code for the TV/Monitor.
Input : The Input Source Code for the TV/Monitor.
Aspect : The Image size Code for the TV/Monitor.
N Time NF : On Time On/Off value for the TV/Monitor.
F Time NF : Off Time On/Off value for the TV/Monitor.
●
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x00
ERR
ERR : Error Code that shows the type of the error that occurred.
0
Check Sum Error
1
Others
Display S/W, VD Business Team, Samsung Electronics
7
SEC-VD-DSW External Control - 0008
2) Time Control
●
Function
The Computer controls the current time for the TV/Monitor.
●
●
Get Time Status
Header
Command
0xAA
0x01
ID
Data Length
0
Check
Sum
Data Length
Data 1
Data 2
Data 3
Data 4
6
0
H Time
M Time
0
Set Time
Header
Command
0xAA
0x01
Data 5
Data 6
0
0
ID
Check
Sum
H Time : The Hour Value for the TV/Monitor ( 0 ~ 23 )
M Time : The Minute Value for the TV/Monitor ( 0 ~ 59 )
●
Ack
Header
Command
0xAA
0xFF
Val 3
Val 4
M Time
0
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
8
'A'
0x01
0
H Time
Val 5
Val 6
0
0
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x01
ERR
Check
Sum
ID
H Time, M Time : Same as above
●
Nak
Header
Command
0xAA
0xFF
ID
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics
8
SEC-VD-DSW External Control - 0008
3) On Time Control
●
Function
The Computer controls when the TV/Monitor turns on.
●
●
Get On Time Status
Header
Command
0xAA
0x02
ID
Data Length
0
Check
Sum
Data Length
Data 1
6
0
Set On Time
Header
Command
0xAA
0x02
Data 5
Data 6
N Time NF N Time SC
ID
Data 2
Data 3
Data 4
N H Time N M Time N Time VR
Check
Sum
N H Time : The On Time Hour Value for the TV/Monitor ( 0 ~ 23 )
N M Time : The On Time Minute Value for the TV/Monitor ( 0 ~ 59 )
N Time VR : The On Time Volume Value for the TV/Monitor ( 0 ~ 100 )
N Time NF : The On Time ON/OFF value for the TV/MonitorTV / Monitor
1
On Time ON
0
On Time OFF
N Time SC : The source value for the On Time ON/OFF Control
(See 'Input Source Control')
●
Ack
Header
Command
0xAA
0xFF
Val 3
Val 4
ID
Val 5
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
8
'A'
0x02
0
N H Time
Val 6
Check
Sum
Check
Sum
N M Time N Time VR N Time NF N Time SC
N H Time, N M Time, N Time VR, N Time NF, N Time SC : 상동
●
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x02
ERR
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics
9
SEC-VD-DSW External Control - 0008
4) Off Time Control
●
Function
The Computer controls when the TV/Monitor turns off.
●
●
Get Off Time Status
Header
Command
0xAA
0x03
ID
Data Length
0
Check
Sum
Data Length
Data 1
6
0
Set Off Time
Header
Command
0xAA
0x03
Data 5
Data 6
F Time NF
0
ID
Data 2
Data 3
F H Time F M Time
Data 4
0
Check
Sum
F H Time
: The Off Time Hour Value for the TV/Monitor ( 0 ~ 23 )
F M Time
: The Off Time Minute Value for the TV/Monitor ( 0 ~ 59 )
F Time NF : The Off Time ON/OFF value for the TV/Monitor
●
1
Off Time ON
0
Off Time OFF
Ack
Header
Command
0xAA
0xFF
Val 3
Val 4
F M Time
0
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
8
'A'
0x03
0
F H Time
Val 5
Val 6
F Time NF
0
Check
Sum
Check
Sum
ID
F H Time, F M Time, F Time NF : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x03
ERR
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 10
SEC-VD-DSW External Control - 0008
5) Video Control (AV, S-Video, Component Only)
●
Function
The Computer shows the screen setting for the TV/Monitor.
●
●
Get Video Status
Header
Command
0xAA
0x04
Header
Command
0xAA
0xFF
Val 3
Val 4
Sharpness
Color
Data Length
0
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
0x0A
'A'
0x04
Contrast
Brightness
Val 5
Val 6
Val 7
Val 8
Tint
ColorTone
0
0
Check
Sum
ID
Ack
ID
Contrast, Brightness, Sharpness, Color, Tint, ColorTone : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x04
ERR
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 11
SEC-VD-DSW External Control - 0008
6) RGB Control (PC1, PC2 Only)
●
Function
The Computer controls the screen setting for the TV/Monitor.
●
●
Get RGB Status
Header
Command
0xAA
0x06
Header
Command
0xAA
0xFF
Val 3
Val 4
Val 5
0
0
0
ID
Data Length
0
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
0x0A
'A'
0x06
Contrast
Brightness
Ack
ID
Val 6
Val 7
Val 8
Red Gain Green Gain Blue Gain
Check
Sum
Contrast, Brightness, Red, Green, Blue : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x06
ERR
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 12
SEC-VD-DSW External Control - 0008
7) PIP Status Control
●
Function
The Computer shows the PIP setting for the TV/Monitor.
●
●
Get PIP Status
Header
Command
0xAA
0x07
Header
Command
0xAA
0xFF
Val 3
Val 4
0
0
ID
Data Length
0
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
6
'A'
0x07
P.Size
P.Source
Check
Sum
Ack
ID
Check
Sum
P.Size : The PIP size Value Code of the TV/Monitor.
0x00
PIP Off
0x06
Large
0x08
Small
0x04
Double 1
0x05
Double 2
P.Source : The PIP Source Value Code of the TV/Monitor.
●
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x07
ERR
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 13
SEC-VD-DSW External Control - 0008
8) Maintenance Control
●
Function
The Computer shows the Maintenance setting for the TV/Monitor.
●
●
Get Maintenance Status
Header
Command
0xAA
0x08
Header
Command
0xAA
0xFF
ID
Data Length
0
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
0x12
'A'
0x08
Power
P.Size
Ack
ID
Val 3
Val 4
Val 5
Val 6
Val 7
Val 8
P.Source
Shift
H.Dot
V.Line
S.Time
S.Pattern
Val 9
Val 10
Val 11
Val 12
Val 13
Val 14
A.White
0
Timer
T.Period
T.Time
V.Wall
Val 15
Val 16
V.WallMode
0
Check Sum
Power : The Power Code for the TV/Monitor.
P.Size : The value code for the PIP Size of the TV/Monitor.
P.Source : The value code for the PIP Source of the TV/Monitor.
Shift : The On/Off code for the Pixel Shift of the TV/Monitor.
H.Dot : The value code for the Horizontal Dot of the TV/Monitor. (0~4)
V.Line : The value code for the Vertical Line of the TV/Monitor. (0~4)
S.Time : The value code for the Shift Time of the TV/Monitor. (1~4)
S.Pattern : The On/Off code for the Signal Pattern of the TV/Monitor.
A.White : The On/Off code for the All White of the TV/Monitor.
Timer : The value code for the SBP Timer of the TV/Monitor
T.Period : The value code for the SBP Timer Period of the TV/Monitor. (1~24)
T.Time : The value code for the SBP Timer Time of the TV/Monitor. (1~30)
V.Wall : The value code for the Video Wall of the TV/Monitor.
V.WallMode : The value code for the Video Wall Mode of the TV/Monitor.
●
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x08
ERR
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 14
SEC-VD-DSW External Control - 0008
9) On, Off Timer Status Control
●
Function
The Computer shows the On, Off Timer setting for the TV/Monitor.
●
●
Get On, Off Timer Status
Header
Command
0xAA
0x0A
Header
Command
0xAA
0xFF
ID
Data Length
0
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
0x0F
'A'
0x0A
Power
Input
Ack
ID
Val 3
Val 4
Val 5
Val 6
Val 7
Val 8
0
N H Time
N M Time
N Time VR
N Time NF
N Time SC
Val 9
Val 10
Val 11
Val 12
Val 13
0
F H Time
F M Time
N Time NF
0
Check Sum
Power : The Power Code for the TV/Monitor.
N H Time : The On Time Hour Value for the TV/Monitor. ( 0 ~ 23 )
N M Time : The On Time Minutes Value for the TV/Monitor. ( 0 ~ 59 )
N Time VR : The On Time Volume Value for the TV/Monitor. ( 0 ~ 100 )
N Time NF : The On Time ON/OFF value for the TV/Monitor. ( 0 ~ 1 )
N Time SC : The source value for the On Time On/Off control.
(See 'Input Source Control')
F H Time : The Off Time Hour Value for the TV/Monitor.( 0 ~ 23 )
F M Time : The Off Time Minutes Value for the TV/Monitor. ( 0 ~ 59 )
F Time NF : The Off Time ON/OFF value for the TV/Monitor. ( 0 ~ 1 )
●
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x0A
ERR
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 15
SEC-VD-DSW External Control - 0008
10) Model Number Control
●
Function
The Computer identifies and displays the TV/Monitor's Model Number.
●
●
Get Model Number Status
Header
Command
0xAA
0x10
Data Length
ID
0
Check
Sum
Ack
Header
Command
0xAA
0xFF
Val 3
Check
Sum
0
ID
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
0x05
'A'
0x10
Species
Model
Check
Sum
Species : TV / Monitor of panel used for the TV/Monitor.
0x01
PDP
0x02
LCD
0x03
DLP
Model : TV / Monitor's model name.
●
0x01
PPM50H2
0x02
PPM42S2
0x03
PS-42P2ST
0x04
PS-50P2HT
0x05
SyncMaster 400T
0x06
SyncMaster 403T
0x07
PPM42S3, SPD-42P3SM
0x08
PPM50H3, SPD-50P3HM
0x09
PPM63H3, SPD-63P3HM
0x0A
PS-42P3ST
0x0B
SyncMaster 323T
0x0C
SyncMaster 403T - CT40CS(N)
0x0D
PPMxxM5x
Nak
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x10
ERR
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 16
SEC-VD-DSW External Control - 0008
11) Power Control
●
Function
The Computer turns the TV/Monitor ON/OFF.
●
●
Get Power ON/OFF Status
Header
Command
0xAA
0x11
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Power
Set Power ON/OFF
Header
Command
0xAA
0x11
ID
Check
Sum
Power : The Power Code for the TV/Monitor.
●
1
Power ON
0
Power OFF
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x11
Power
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x11
ERR
Check
Sum
Power : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 17
SEC-VD-DSW External Control - 0008
12) Volume Control
●
Function
The Computer changes the Volume level of the TV/Monitor.
●
●
Get Volume Status
Header
Command
0xAA
0x12
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Volume
Set Volume
Header
Command
0xAA
0x12
ID
Check
Sum
Volume : The Volume level Value Code of the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x12
Volume
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x12
ERR
Check
Sum
Volume : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 18
SEC-VD-DSW External Control - 0008
13) Mute Control
●
Function
The Computer turns the Mute of the TV/Monitor ON/OFF.
●
●
Get Mute ON/OFF Status
Header
Command
0xAA
0x13
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Mute
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x13
Mute
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x13
ERR
Set Mute ON/OFF
Header
Command
0xAA
0x13
ID
Mute : The Mute Code for the TV/Monitor.
●
1
Mute ON
0
Mute OFF
Ack
Header
Command
0xAA
0xFF
ID
Check
Sum
Mute : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 19
SEC-VD-DSW External Control - 0008
14) Input Source Control
●
Function
The Computer changes the Input Source of the TV/Monitor.
●
●
Get Input Source Status
Header
Command
0xAA
0x14
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Input
Set Input Source
Header
Command
0xAA
0x14
ID
Check
Sum
Input : The Input Source Code for the TV / Monitor
●
0x0C
AV
0x04
S-Video
0x08
Component
0x15
PC1
0x16
PC2
0x18
DVI
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x14
Input
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x14
ERR
Check
Sum
Input : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 20
SEC-VD-DSW External Control - 0008
15) Image Size Control
●
Function
The Computer adjusts the Image Size of the TV/Monitor.
It is not operated when the Video Wall is on.
●
●
Get Image Size Status
Header
Command
0xAA
0x15
Data Length
ID
0
Check
Sum
Data Length
Data 1
1
Aspect
Set Image Size
Header
Command
0xAA
0x15
ID
Check
Sum
Aspect : The Computer adjusts the Image Size of the TV/Monitor.
PC1, PC2, DVI
0x10
16 : 9
0x18
4 : 3
AV, S-VIdeo, Component
0x01
16 : 9
0x02
Panorama
0x05
Zoom 1
0x06
Zoom 2
0x03
14 : 9
0x0B
4 : 3
Note) The computer adjusts the Panorama settings of the TV/Monitor.
It is operated when the current signal sets to Component(480i and 576i).
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x15
Aspect
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x15
ERR
Check
Sum
Aspect : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 21
SEC-VD-DSW External Control - 0008
16) Contrast Control (AV, S-Video, Component Only)
●
Function
The Computer adjusts the Contrast of the TV/Monitor.
●
●
Get Contrast Status
Header
Command
0xAA
0x24
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Contrast
Set Contrast
Header
Command
0xAA
0x24
ID
Check
Sum
Contrast : The Contrast Value Code for the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x24
Contrast
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x24
ERR
Check
Sum
Contrast : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 22
SEC-VD-DSW External Control - 0008
17) Brightness Control (AV, S-Video, Component Only)
●
Function
The Computer adjusts the Brightness setting of the TV/Monitor.
●
●
Get Brightness Status
Header
Command
0xAA
0x25
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Brightness
Set Brightness
Header
Command
0xAA
0x25
ID
Check
Sum
Brightness : The Brightness Value Code for the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x25
Brightness
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x25
ERR
Check
Sum
Brightness : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 23
SEC-VD-DSW External Control - 0008
18) Sharpness Control (AV, S-Video, Component Only)
●
Function
The Computer adjusts the Sharpness of the TV/Monitor.
●
●
Get Sharpness Status
Header
Command
0xAA
0x26
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Sharpness
Set Sharpness
Header
Command
0xAA
0x26
ID
Check
Sum
Sharpness : The Sharpness Value Code for the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x26
Sharpness
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x26
ERR
Check
Sum
Sharpness : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 24
SEC-VD-DSW External Control - 0008
19) Color Control (AV, S-Video, Component Only)
●
Function
The Computer adjusts the Color setting of the TV/Monitor.
●
●
Get Color Status
Header
Command
0xAA
0x27
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Color
Set Color
Header
Command
0xAA
0x27
ID
Check
Sum
Color : The Color Value Code for the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x27
Color
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x27
ERR
Check
Sum
Color : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 25
SEC-VD-DSW External Control - 0008
20) Tint Control (AV, S-Video, Component Only)
●
Function
The Computer adjusts the Tint of the TV/Monitor when the video format is NTSC.
Note : It dose not work in PAL signal.
●
●
Get Tint Status
Header
Command
0xAA
0x28
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Tint
Set Tint
Header
Command
0xAA
0x28
ID
Check
Sum
Tint : The Tint Value Code for the TV/Monitor ( 0 ~ 100 )
●
R
Tint Value
G
(100 - Tint) Value
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x28
Tint
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x28
ERR
Check
Sum
Tint : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 26
SEC-VD-DSW External Control - 0008
21) Red Gain Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Red Gain of the TV/Monitor.
●
●
Get Red Gain Status
Header
Command
0xAA
0x29
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Red
Set Red Gain
Header
Command
0xAA
0x29
ID
Check
Sum
Red : The Red Gain level Value Code of the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x29
Red
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x29
ERR
Check
Sum
Red : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 27
SEC-VD-DSW External Control - 0008
22) Green Gain Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Green Gain of the TV/Monitor.
●
●
Get Green Gain Status
Header
Command
0xAA
0x2A
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Green
Set Green Gain
Header
Command
0xAA
0x2A
ID
Check
Sum
Green : The Green Gain level Value Code of the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x2A
Green
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x2A
ERR
Check
Sum
Green : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 28
SEC-VD-DSW External Control - 0008
23) Blue Gain Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Blue Gain of the TV/Monitor.
●
●
Get Blue Gain Status
Header
Command
0xAA
0x2B
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Blue
Set Blue Gain
Header
Command
0xAA
0x2B
ID
Check
Sum
Blue : The Blue Gain level Value Code of the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x2B
Blue
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x2B
ERR
Check
Sum
Blue : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 29
SEC-VD-DSW External Control - 0008
24) Coarse Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Coarse settings of the TV/Monitor.
It is operated when the current Signal sets to DTV(480p, 576p,720 p, 1080i).
●
Get Coarse Status
None
●
Set Coarse
Header
Command
0xAA
0x2F
ID
Data Length
Data 1
1
Coarse
Check
Sum
Coarse : The Frequency Increase/Decrease Code for the TV/Monitor.
●
1
Increase
0
Decrease
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x2F
Coarse
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x2F
ERR
Check
Sum
Coarse : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 30
SEC-VD-DSW External Control - 0008
25) Fine Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Fine settings of the TV/Monitor.
It is operarted when the current Signal sets to DTV(480p, 576p,720 p, 1080i).
●
Get Fine Status
None
●
Set Fine
Header
Command
0xAA
0x30
ID
Data Length
Data 1
1
Fine
Check
Sum
Fine : The Phase Increase/Decrease Code for the TV/Monitor.
●
1
Increase
0
Decrease
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x30
Fine
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x30
ERR
Check
Sum
Fine : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 31
SEC-VD-DSW External Control - 0008
26) H-Position Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Horizontal Position settings of the TV/Monitor.
It is operarted when the current Signal sets to DTV(480p, 576p,720 p, 1080i).
●
Get H-Position Status
None
●
Set H-Position
Header
Command
0xAA
0x31
ID
Data Length
Data 1
1
H-Pos
Check
Sum
H-Pos : The H-Position Increase/Decrease Code for the TV/Monitor.
●
1
Shift to the right
0
Shift to the left
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x31
H-Pos
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x31
ERR
Check
Sum
H-Pos : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 32
SEC-VD-DSW External Control - 0008
27) V-Position Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Vertical Position settings of the TV/Monitor.
It is operarted when the current Signal sets to DTV(480p, 576p,720 p, 1080i).
●
Get V-Position Status
None
●
Set V-Position
Header
Command
0xAA
0x32
ID
Data Length
Data 1
1
V-Pos
Check
Sum
V-Pos : The V-Position Increase/Decrease Code for the TV/Monitor.
●
1
Shifts downward
0
Shifts upward
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x32
V-Pos
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x32
ERR
Check
Sum
V-Pos : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 33
SEC-VD-DSW External Control - 0008
28) Clear Menu Control
●
Function
The computer exits the Menu OSD on the TV/Monitor screen.
●
Get Clear Menu Status
None
●
Set Clear Menu
Header
Command
0xAA
0x34
ID
Data Length
Data 1
1
Clear
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x34
Clear
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x34
ERR
Clear : 0x00 (Always)
●
●
Ack
Header
Command
0xAA
0xFF
Header
Command
0xAA
0xFF
ID
Check
Sum
Nak
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 34
SEC-VD-DSW External Control - 0008
29) IR Lock Control
●
Function
The computer controls Enable/Disable for the IR Lock of the TV/Monitor.
It is operated irrespective of power On/Off.
●
●
Get IR Lock Status
Header
Command
0xAA
0x36
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
RMC
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x36
RMC
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x36
ERR
Set IR Lock
Header
Command
0xAA
0x36
ID
RMC : The Power Code for the TV/Monitor.
●
1
Remocon Enable
0
Remocon Disable
Ack
Header
Command
0xAA
0xFF
ID
Check
Sum
RMC : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 35
SEC-VD-DSW External Control - 0008
30) RGB Contrast Control (PC1, PC2, DVI Only)
●
Function
The Computer adjusts the Contrast setting of the TV/Monitor when the Aspect is
RGB.
●
●
Get Contrast Status
Header
Command
0xAA
0x37
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Contrast
Set Contrast
Header
Command
0xAA
0x37
ID
Check
Sum
Contrast : The RGB Contrast Value Code for the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x37
Contrast
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x37
ERR
Check
Sum
Contrast : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 36
SEC-VD-DSW External Control - 0008
31) RGB Brightness Control (PC1, PC2, DVI Only)
●
Function
The Computer adjusts the Brightness setting of the TV/Monitor when the Aspect is
RGB.
●
●
Get Brightness Status
Header
Command
0xAA
0x38
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
Brightness
Set Brightness
Header
Command
0xAA
0x38
ID
Check
Sum
Brightness : The RGB Brightness Value Code for the TV/Monitor ( 0 ~ 100 )
●
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x38
Brightness
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x38
ERR
Check
Sum
Brightness : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 37
SEC-VD-DSW External Control - 0008
32) Zoom Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Aspect's Zoom of the TV/Monitor.
●
Get Zoom Status
None
●
Set Zoom
Header
Command
0xAA
0x39
ID
Data Length
Data 1
1
Zoom
Check
Sum
Zoom : The Zoom Increase/Decrease Code for the TV/Monitor.
●
1
Increase
0
Decrease
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x39
Zoom
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x39
ERR
Check
Sum
Zoom : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 38
SEC-VD-DSW External Control - 0008
33) H-Panning Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Horizontal Panning of the TV/Monitor.
Avalable only with TV/ Monitor in which the Zoom(0x39) is on.
●
Get H-Panning Status
None
●
Set H-Panning
Header
Command
0xAA
0x3A
ID
Data Length
Data 1
1
H-Pan
Check
Sum
H-Pan : The H-Panning Increase/Decrease Code for the TV/Monitor.
●
1
shift to the right
0
shift to the left
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x3A
H-Pan
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x3A
ERR
Check
Sum
H-Pan : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 39
SEC-VD-DSW External Control - 0008
34) V-Panning Control (PC1, PC2 Only)
●
Function
The Computer adjusts the Vertical Panning of the TV/Monitor.
Avalable only with TV/ Monitor in which the Zoom(0x39) is on.
●
Get V-Panning Status
None
●
Set V-Panning
Header
Command
0xAA
0x3B
ID
Data Length
Data 1
1
V-Pan
Check
Sum
V-Pan : The V-Panning Increase/Decrease Code for the TV/Monitor.
●
1
shifts downward
0
shifts upnward
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x3B
V-Pan
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x3B
ERR
Check
Sum
V-Pan : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 40
SEC-VD-DSW External Control - 0008
35) PIP On / Off Control
●
Function
The Computer turns the PIP function of the TV/Monitor ON/OFF.
It is not operated when the Video Wall is on.
●
●
Get PIP ON/OFF Status
Header
Command
0xAA
0x3C
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
PIP
Set PIP ON/OFF
Header
Command
0xAA
0x3C
ID
Check
Sum
PIP : The PIP On/Off Code for the TV/Monitor.
●
1
PIP ON
0
PIP OFF
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x3C
PIP
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x3C
ERR
Check
Sum
PIP : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 41
SEC-VD-DSW External Control - 0008
36) Auto Adjustment Control (PC1, PC2 Only)
●
Function
The Computer adjusts the RGB screen Setting Automatically.
It is not operated when the current Signal sets to DTV(480p, 576p, 720p, 1080i).
●
Get Auto Adjustment Status
None
●
Set Auto Adjustment
Header
Command
0xAA
0x3D
ID
Data Length
Data 1
1
Auto
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x3D
Auto
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x3D
ERR
Auto : 0x00 (Always)
●
●
Ack
Header
Command
0xAA
0xFF
Header
Command
0xAA
0xFF
ID
Check
Sum
Nak
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 42
SEC-VD-DSW External Control - 0008
37) Color Tone Control (AV, S-Video, Component Only)
●
Function
The Computer adjusts the Color Tone setting of the TV/Monitor.
●
●
Get Color Tone Status
Header
Command
0xAA
0x3E
ID
Data Length
0
Check
Sum
Set Color Tone
Header
Command
0xAA
0x3E
ID
Data Length
Data 1
1
Color Tone
Check
Sum
Color Tone : The Color Tone Value Code for the TV/Monitor. ( 0 ~ 4 )
●
0x00
Cool 2
0x01
Cool 1
0x02
Normal
0x03
Warm 1
0x04
Warm 2
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x3E
Color Tone
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x3E
ERR
Check
Sum
Brightness : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 43
SEC-VD-DSW External Control - 0008
38) PIP Source Control
●
Function
The Computer adjusts the PIP Source of the TV/Monitor.
Available only when the PIP function is on.
●
●
Get PIP Source Status
Header
Command
0xAA
0x40
Data Length
ID
0
Check
Sum
Data Length
Data 1
1
P.Source
Set PIP Source
Header
Command
0xAA
0x40
ID
Check
Sum
P.Source : The Input Source Value Code of the TV/Monitor.
Changing the PIP source may not be available depending on the main source.
See table below.
●
AV
S-Video
Component
PC1
PC2
DVI
AV
X
X
X
O
○
X
S-Video
X
X
X
O
○
X
Component
X
X
X
O
○
X
PC1
○
○
○
X
X
○
PC2
○
○
○
X
X
○
DVI
X
X
X
O
○
X
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x40
P.Source
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x40
ERR
Check
Sum
P.Source : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 44
SEC-VD-DSW External Control - 0008
39) Main-PIP Swap Control
●
Function
The Computer swaps the main screen with the PIP screen.
Available only when the PIP function is on.
●
Get Main-PIP Swap Status
None
●
Set Main-PIP Swap
Header
Command
0xAA
0x41
ID
Data Length
Data 1
1
Swap
Check
Sum
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x41
Swap
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x41
ERR
Swap : 0x00 (Always)
●
●
Ack
Header
Command
0xAA
0xFF
Header
Command
0xAA
0xFF
ID
Check
Sum
Nak
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 45
SEC-VD-DSW External Control - 0008
40) PIP Size Control
●
Function
The Computer changes the PIP size of the TV/Monitor.
When the PIP is off, it is to be on automatically.
●
●
Get PIP Size Status
Header
Command
0xAA
0x42
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
P.Size
Set PIP Size
Header
Command
0xAA
0x42
ID
Check
Sum
P.Size : The PIP size Value Code for the TV/Monitor
●
0x00
PIP Off
0x06
Large
0x08
Small
0x04
Double 1
0x05
Double 2
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x42
P.Size
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x42
ERR
Check
Sum
P.Size : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 46
SEC-VD-DSW External Control - 0008
41) PIP Locate Control
●
Function
The Computer adjusts the PIP position of the TV/Monitor.
Available only when the PIP function is on.
●
Get PIP Locate Status
None
●
Set PIP Locate
Header
Command
0xAA
0x43
ID
Data Length
Data 1
1
P.Locate
Check
Sum
P.Locate : The PIP Locate Increase/Decrease Code for the TV/Monitor.
●
0
PIP Off(Get Only)
1
Upper Left
2
Upper Right
3
Lower Right
4
Lower Left
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x43
P.Locate
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x43
ERR
Check
Sum
P.Locate : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 47
SEC-VD-DSW External Control - 0008
42) Sound Select Control
●
Function
The Computer adjusts the Sound Setting of the TV/Monotor when the PIP function is
ON.
Available only when the PIP function is on.
●
●
Get Sound Select
Header
Command
0xAA
0x47
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
S.Selct
Set Sound Select
Header
Command
0xAA
0x47
ID
Check
Sum
S.Select : The Sound Select code for the TV/Monitor
●
1
Main
0
Sub
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x47
S.Select
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x47
ERR
Check
Sum
S.Select : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 48
SEC-VD-DSW External Control - 0008
43) Pixel Shift Control
●
Function
The Computer adjusts the Pixel Shift function of the TV/Monitor.
●
●
Get Pixel Shift Status
Header
Command
0xAA
0x4C
ID
Data Length
0
Check
Sum
Data Length
Data 1
Data 2
Data 3
Data 4
0x04
Shift
H.Dot
V.Line
S.Time
Set Pixel Shift
Header
Command
0xAA
0x4C
ID
Check
Sum
Shift : The On/Off code for the Pixel Shift of the TV/Monitor.
Note : When the value of Shift os Off, the value of the H.Dot, V.Lines, S.Time may
not be included in the TV/Monitor.
1
ON
0
OFF
H.Dot : The value code for the Horizontal Dot of the TV/Monitor. (0 ~ 4)
V.Line : The value code for the Vertical Line of the TV/Monitor. (0 ~ 4)
S.Time : The value code for the Shift Time of the TV/Monitor. (1 ~ 4)
●
Ack
Header
Command
0xAA
0xFF
Val 3
Val 4
V.Line
S.Time
ID
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
0x06
'A'
0x4C
Shift
H.Dot
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x4C
ERR
Check
Sum
Check
Sum
Shift, H.Dot, V.Line, S.Time : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 49
SEC-VD-DSW External Control - 0008
44) Signal Pattern Control
●
Function
The Computer turns the Signal Pattorn function of the TV/Monitor ON/OFF.
●
●
Get Signal Pattern Status
Header
Command
0xAA
0x4D
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
S.Pattern
Set Signal Pattern
Header
Command
0xAA
0x4D
ID
Check
Sum
S.Pattern : The On/Off code for the Signal pattern of the TV/Monitor.
●
1
ON
0
OFF
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x4D
S.Pattern
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x4D
ERR
Check
Sum
S.Pattern : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 50
SEC-VD-DSW External Control - 0008
45) All White Control
●
Function
The Computer turns the All White function of the TV/Monitor ON/OFF.
●
●
Get All White Status
Header
Command
0xAA
0x4E
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
A.White
Set All White
Header
Command
0xAA
0x4E
ID
Check
Sum
A.White : The On/Off code for the All White of the TV/Monitor.
●
1
ON
0
OFF
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x4E
A.White
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x4E
ERR
Check
Sum
A.White : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 51
SEC-VD-DSW External Control - 0008
46) Video Wall Control
●
Function
The Computer turns the Video Wall function of the TV/Monitor ON/OFF.
●
●
Get Video Wall Status
Header
Command
0xAA
0x4F
Data Length
ID
0
Check
Sum
Data Length
Data 1
1
V.Wall
Set Video Wall
Header
Command
0xAA
0x4F
ID
Check
Sum
V.Wall : The value code for the Video Wall of the TV/Monitor.
●
Set
2 X 2
3 X 3
4 X 4
1 X 5
5 X 1
OFF
0x00
0x00
0x00
0x00
0x00
No. 1
0x11
0x21
0x31
0x41
0x51
No. 2
0x12
0x22
0x32
0x42
0x52
No. 3
0x13
0x23
0x33
0x43
0x53
No. 4
0x14
0x24
0x34
0x44
0x54
No. 5
0x25
0x35
0x45
0x55
...
...
...
No. 9
0x29
0x39
...
...
No. 16
0x40
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x4F
V.Wall
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x4F
ERR
Check
Sum
V.Wall : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 52
SEC-VD-DSW External Control - 0008
47) SBP Timer Control
●
Function
The Computer have the Screen Burn Protection Timer set of the TV/Monitor.
●
●
Get SBP Timer Status
Header
Command
0xAA
0x5B
ID
Data Length
0
Check
Sum
Data Length
Data 1
Data 2
Data 3
3
Timer
T.Period
T.Time
Set SBP Timer
Header
Command
0xAA
0x5B
ID
Check
Sum
Timer : The value code for the SBP Timer of the TV/Monitor.
0
OFF
1
Signal Pattern
2
All White
T.Period : The value code for the SBP Timer Period of the TV/Monitor. (1~24 Hr.)
T.Time : The value code for the SBP Timer Time of the TV/Monitor. (1~30 min.)
●
Ack
Header
Command
0xAA
0xFF
Val 3
Check
Sum
T.Time
ID
Data Length
Ack/Nak
r-CMD
Val 1
Val 2
5
'A'
0x5B
Timer
T.Period
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x5B
ERR
Check
Sum
Timer, T.Period, T.Time : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 53
SEC-VD-DSW External Control - 0008
48) Video Wall Mode Control
●
Function
The Computer changes the mode of the TV/Monitor when Video Wall function is ON.
Available only when the Video Wall function is on.
●
●
Get Video Wall Mode Status
Header
Command
0xAA
0x5C
ID
Data Length
0
Check
Sum
Data Length
Data 1
1
WallMode
Set Video Wall Mode
Header
Command
0xAA
0x5C
ID
Check
Sum
WallMode : The code for the Video Wall Mode of the TV/Monitor.
●
1
Natural
0
Full
Ack
Header
Command
0xAA
0xFF
ID
Data Length
Ack/Nak
r-CMD
Val 1
3
'A'
0x5C
WallMode
Data Length
Ack/Nak
r-CMD
Val 1
3
'N'
0x5C
ERR
Check
Sum
WallMode : Same as avobe
●
Nak
Header
Command
0xAA
0xFF
ID
Check
Sum
ERR : Error Code that shows the type of the error that occurred.
Display S/W, VD Business Team, Samsung Electronics 54